CMM3-MIB

All MIBs › CMM3-MIB

Organization: Motorola

Last Updated: 2003-05-15

Category: DOCSIS and Cable

Description: Provides management objects for CMM3 cable modem hardware monitoring and configuration.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is CMM3-MIB?

CMM3-MIB provides management objects for a CMM3 cable headend hardware module used in DOCSIS cable networks, covering configuration, operational status, GPS timing reference, and switch/redundancy state. It exposes distinct object groups for status (cmmStatus), configuration (cmmConfig), redundancy switching (cmmSwitch), GPS reference (cmmGps), and a historical event log (cmmEventLog), giving it broad coverage of both configuration and operational health data. This MIB is squarely a hardware-status monitoring MIB: the status and event-log objects surface operational faults and state changes, while the GPS objects are critical because loss of GPS lock can affect the timing synchronization the cable network depends on for DOCSIS operation. It is a self-contained vendor MIB for this specific hardware module rather than an extension of a broader IETF standard. It is deployed in cable operator headends where CMM3 modules provide timing and redundancy management for the surrounding cable plant equipment. Engineers can download the CMM3-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in CMM3-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

cable headend CMM3 hardware module

Monitoring Examples

An operator polls cmmStatus to check the CMM3 unit's overall operational health and cmmGps to confirm the GPS receiver still has a valid lock, since loss of GPS sync can degrade DOCSIS timing across the plant. The cmmSwitch objects reveal whether the unit has failed over to a redundant path, and cmmEventLog provides a history of state-change and fault events an operator would review after an alarm to determine root cause.

What Can Be Monitored

overall unit operational status
GPS receiver lock/sync status
redundancy switch state
configuration parameters
historical event/alarm log entries

Imported Objects

From SNMPv2-CONF

OBJECT-GROUP

From SNMPv2-SMI

Counter32
Counter64
Gauge32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE

From SNMPv2-TC

DisplayString

From WHISP-GLOBAL-REG-MIB

whispBox	OBJECT-IDENTITY
whispCMM	OBJECT-IDENTITY
whispModules	OBJECT-IDENTITY

From WHISP-TC-MIB

EventString
WhispLUID
WhispMACAddress

How to Use in IPNetwork Monitor

Example using txDropPkts OID:

Select a cable headend hardware module as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type txDropPkts into the Find box to locate it in the OID tree, then select it and click OK. This counter is incremented every time a transmit packet is dropped due to lack of resources (e.g., transmit FIFO underflow), or an internal MAC sublayer transmit error not counted by in either the TxLateCollision or the TxExcessiveCollision counters. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases between polls, since a rising count of errors, failures, or discards often points to a real underlying problem. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
cmmIIIMibModule	1.3.6.1.4.1.161.19.1.1.15			This module contains CMM3 MIB definitions.
cmmGroups	1.3.6.1.4.1.161.19.3.4.1
cmmSwitchGroup	1.3.6.1.4.1.161.19.3.4.1.1			CMMIII switch group.
cmmConfigGroup	1.3.6.1.4.1.161.19.3.4.1.2			CMMIII configuration group.
cmmStatusGroup	1.3.6.1.4.1.161.19.3.4.1.3			CMMIII configuration group.
cmmGPSGroup	1.3.6.1.4.1.161.19.3.4.1.4			CMMIII GPS status group.
cmmSwitch	1.3.6.1.4.1.161.19.3.4.2
cmmSwitchTable	1.3.6.1.4.1.161.19.3.4.2.1		not-accessible	Table of CMM MIB counters
cmmSwitchEntry	1.3.6.1.4.1.161.19.3.4.2.1.1		not-accessible	CMM MIB counters
INT portNumber	1.3.6.1.4.1.161.19.3.4.2.1.1.1	INTEGER	read-only	A unique value for each CMM port. Its value starts from 1.
C32 rxDropPkts	1.3.6.1.4.1.161.19.3.4.2.1.1.2	Counter32	read-only	The number of good packets received by a port that were dropped due to lack of resources(e.g., lack of input buffers)or were dropped due to lack of resources before a determination of the validity of the packet was able to be made (e.g., receive FIFO overflow). The counter is only incremented if the receive error was not counted by either the RxExcessSizeDisc, the RxAlignmentErrors or the RxRCSErrors counters.
C64 rxOctets	1.3.6.1.4.1.161.19.3.4.2.1.1.3	Counter64	read-only	The number of bytes of data received by a port (excluding preamble but including FCS), including bad packets.
C32 rxBroadcastPkts	1.3.6.1.4.1.161.19.3.4.2.1.1.4	Counter32	read-only	The number of good packets received by a port that are directed to the broadcast address. This counter does not include error broadcast packets or valid multicast packets.
C32 rxMulticastPkts	1.3.6.1.4.1.161.19.3.4.2.1.1.5	Counter32	read-only	The number of good packets received by a port that are directed to the multicast address. This counter does not include error multicast packets or valid broadcast packets.
C32 rxSAChanges	1.3.6.1.4.1.161.19.3.4.2.1.1.6	Counter32	read-only	The number of times the SA of good receive packets has changed from the previous value. A count greater than 1 generally indicates the port if connected to a repeater based network.
C32 rxUndersizePkts	1.3.6.1.4.1.161.19.3.4.2.1.1.7	Counter32	read-only	The number of good packets received by a port that are less than 64 bytes long (excluding framing bits but including the FCS).
C32 rxOversizePkts	1.3.6.1.4.1.161.19.3.4.2.1.1.8	Counter32	read-only	The number of good packets received by a port that are greater than 1522 bytes inclusive (excluding framing bits but including the FCS). Note that this counter alone will be incremented for packets in the range 1523-1536 bytes inclusive, whereas both this counter and the RxExcessSizeDisc counter will be incremented for packets of 1537 bytes and higher.
C32 rxFragments	1.3.6.1.4.1.161.19.3.4.2.1.1.9	Counter32	read-only	The number of packets received by a port that are less than 64 bytes(excluding framing bits) and have either an FCS error or an alignment error.
C32 rxJabbers	1.3.6.1.4.1.161.19.3.4.2.1.1.10	Counter32	read-only	The number of packets received by a port that are longer than 1522 bytes and have either an FCS error or an alignment error.
C32 rxUnicastPkts	1.3.6.1.4.1.161.19.3.4.2.1.1.11	Counter32	read-only	The number of good packets received by a port that are addressed to a unicast address.
C32 rxAlignmentErrors	1.3.6.1.4.1.161.19.3.4.2.1.1.12	Counter32	read-only	The number of packets received by a port that have a length (excluding framing bits but including FCS) between 64 and 1522 bytes, inclusive, and have a bad FCS with a non-integral number of bytes.
C32 rxFCSErrors	1.3.6.1.4.1.161.19.3.4.2.1.1.13	Counter32	read-only	The number of packets received by a port that have a length (excluding framing bits but including FCS) between 64 and 152 bytes, and have a bad FCS with an integral number of bytes.
C64 rxGoodOctets	1.3.6.1.4.1.161.19.3.4.2.1.1.14	Counter64	read-only	The total number of bytes in all good packets received by a port (excluding framing bits but including FCS).
C32 rxExcessSizeDisc	1.3.6.1.4.1.161.19.3.4.2.1.1.15	Counter32	read-only	The number of good packets received by a port that are greater than 1536 bytes (excluding framing bits but including FCS) and were discarded due to excessive length. Note that the RxOversizePkts counter alone is incremented for packets in the range of 1523-1536 bytes inclusive, whereas both this counter and the RxOversizePkts are incremented for packets of 1537 bytes and higher.
C32 rxPausePkts	1.3.6.1.4.1.161.19.3.4.2.1.1.16	Counter32	read-only	The number of PAUSE frame received by a port. The PAUSE frame must have a valid MAC Control Frame EtherType field (88-08h), have a destination MAC address of either the MAC Control frame reserved multicast address(01-80-c2-00-00-011) or the unique MAC address associated with the specific port, a valid PAUSE Opcode (00-01), be a minimum of 64 bytes in length (excluding preamble but including FCS), and have a valid CRC. Although an 802.3 compliant MAC is only permitted to transmit PAUSE frames when in full duplex mode, with flow control enabled, and with the transfer of PAUSE frames determined by the result of auto-negotiation, an 802.3 MAC receiver is required to count all received PAUSE frames, regardless of its half/full-duplex status. An indication that a MAC is in half-duplex with the RxPausePkts incrementing indicates a non-compliant transmitting device on the network.
C32 rxSymbolErrors	1.3.6.1.4.1.161.19.3.4.2.1.1.17	Counter32	read-only	The total number of times a valid length packet was received at a port and at least one invalid data symbol was detected. Counter only increment once per carrier event and does not increment on detection of collision during the carrier event.
C32 txDropPktsEx	1.3.6.1.4.1.161.19.3.4.2.1.1.18	Counter32	read-only	This counter is incremented every time a transmit packet is dropped due to lack of resources (e.g., transmit FIFO underflow), or an internal MAC sublayer transmit error not counted by in either the TxLateCollision or the TxExcessiveCollision counters.
C64 txOctets	1.3.6.1.4.1.161.19.3.4.2.1.1.19	Counter64	read-only	The total number of good bytes of data transmitted by a port (excluding preamble but including FCS).
C32 txBroadcastPkts	1.3.6.1.4.1.161.19.3.4.2.1.1.20	Counter32	read-only	The number of good packets transmitted by a port that are directed to a broadcast address. This counter does not include errored broadcast packets or valid multicast packets.
C32 txMulticastPkts	1.3.6.1.4.1.161.19.3.4.2.1.1.21	Counter32	read-only	The number of good packets transmitted by a port that are directed to a multicast address. This counter does not include errored multicast packets or valid broadcast packets.
C32 txCollisions	1.3.6.1.4.1.161.19.3.4.2.1.1.22	Counter32	read-only	The number of collision experienced by a port during packet transmissions.
C32 txUnicastPkts	1.3.6.1.4.1.161.19.3.4.2.1.1.23	Counter32	read-only	The number of good packets transmitted by a port that are addressed to a unicast address.
C32 txSingleCollision	1.3.6.1.4.1.161.19.3.4.2.1.1.24	Counter32	read-only	The number packets successfully transmitted by a port that experienced exactly one collision.
C32 txMultipleCollision	1.3.6.1.4.1.161.19.3.4.2.1.1.25	Counter32	read-only	The number packets successfully transmitted by a port that experienced more than one collision.
C32 txDeferredTransmit	1.3.6.1.4.1.161.19.3.4.2.1.1.26	Counter32	read-only	The number packets successfully transmitted by a port for which the first transmission attempt is delayed because medium is busy.
C32 txLateCollision	1.3.6.1.4.1.161.19.3.4.2.1.1.27	Counter32	read-only	The number of times that a collision is detected later than 512 bit-times into the transmission of a packet.
C32 txExcessiveCollision	1.3.6.1.4.1.161.19.3.4.2.1.1.28	Counter32	read-only	The number of packets that are not transmitted from a port because the packet experienced 16 transmission attempts.
C32 txPausePkts	1.3.6.1.4.1.161.19.3.4.2.1.1.29	Counter32	read-only	The number of PAUSE frame transmitted by a port. The MAC resolve to full duplex mode, with 803.3x flow control PAUSE frame exchange enabled at the completion of auto-negotiation.
C32 txFrameInDisc	1.3.6.1.4.1.161.19.3.4.2.1.1.30	Counter32	read-only	The number of valid packets received which are discarded by the forwarding process due to lack of space on an output queue. Note: not maintained or reported in the MIB counters. Located in Congestion registers. This attribute only increments if a network device is not acting in compliance with a flow control request, or the BCM5327M internal flow control/buffering scheme has been misconfigured.
C32 pkts64Octets	1.3.6.1.4.1.161.19.3.4.2.1.1.31	Counter32	read-only	The number of packets (including error packets) that are 64 bytes long.
C32 pkts65to127Octets	1.3.6.1.4.1.161.19.3.4.2.1.1.32	Counter32	read-only	The number of packets (including error packets) that are between 65 and 127 bytes long.
C32 pkts128to255Octets	1.3.6.1.4.1.161.19.3.4.2.1.1.33	Counter32	read-only	The number of packets (including error packets) that are between 128 and 255 bytes long.
C32 pkts256to511Octets	1.3.6.1.4.1.161.19.3.4.2.1.1.34	Counter32	read-only	The number of packets (including error packets) that are between 256 and 511 bytes long.
C32 pkts512to1023Octets	1.3.6.1.4.1.161.19.3.4.2.1.1.35	Counter32	read-only	The number of packets (including error packets) that are between 512 and 1023 bytes long.
C32 pkts1024to1522Octets	1.3.6.1.4.1.161.19.3.4.2.1.1.36	Counter32	read-only	The number of packets (including error packets) that are between 1024 and 1522 bytes long.
cmmConfig	1.3.6.1.4.1.161.19.3.4.3
INT gpsTimingPulse	1.3.6.1.4.1.161.19.3.4.3.1	INTEGER	read-write	(1) -- Master. (0) -- Slave.
IP lan1Ip	1.3.6.1.4.1.161.19.3.4.3.2	IpAddress	read-write	LAN 1 IP.
IP lan1SubnetMask	1.3.6.1.4.1.161.19.3.4.3.3	IpAddress	read-write	LAN 1 subnet mask.
IP defaultGateWay	1.3.6.1.4.1.161.19.3.4.3.4	IpAddress	read-write	Default gateway
INT port1PowerCtr	1.3.6.1.4.1.161.19.3.4.3.5	INTEGER	read-write	Power control for port 1. (1) -- Power on. (0) -- Power off.
INT port2PowerCtr	1.3.6.1.4.1.161.19.3.4.3.6	INTEGER	read-write	Power control for port 2. (1) -- Power on. (0) -- Power off.
INT port3PowerCtr	1.3.6.1.4.1.161.19.3.4.3.7	INTEGER	read-write	Power control for port 3. (1) -- Power on. (0) -- Power off.
INT port4PowerCtr	1.3.6.1.4.1.161.19.3.4.3.8	INTEGER	read-write	Power control for port 4. (1) -- Power on. (0) -- Power off.
INT port5PowerCtr	1.3.6.1.4.1.161.19.3.4.3.9	INTEGER	read-write	Power control for port 5. (1) -- Power on. (0) -- Power off.
INT port6PowerCtr	1.3.6.1.4.1.161.19.3.4.3.10	INTEGER	read-write	Power control for port 6. (1) -- Power on. (0) -- Power off.
INT port7PowerCtr	1.3.6.1.4.1.161.19.3.4.3.11	INTEGER	read-write	Power control for port 7. (1) -- Power on. (0) -- Power off.
INT port8PowerCtr	1.3.6.1.4.1.161.19.3.4.3.12	INTEGER	read-write	Power control for port 8. (1) -- Power on. (0) -- Power off.
STR displayOnlyAccess	1.3.6.1.4.1.161.19.3.4.3.13	DisplayString	read-write	Display only access to web interface and telnet.
STR fullAccess	1.3.6.1.4.1.161.19.3.4.3.14	DisplayString	read-write	Full access password to web interface and telnet.
STR displayOnlyStatus	1.3.6.1.4.1.161.19.3.4.3.15	DisplayString	read-only	Display only password status.
STR fullAccessStatus	1.3.6.1.4.1.161.19.3.4.3.16	DisplayString	read-only	Full access password status.
INT webAutoUpdate	1.3.6.1.4.1.161.19.3.4.3.17	INTEGER	read-write	Web page auto update in seconds. 0 means disabled.
INT port1Config	1.3.6.1.4.1.161.19.3.4.3.18	INTEGER	read-write	Link speed configuration on port 1.
INT port2Config	1.3.6.1.4.1.161.19.3.4.3.19	INTEGER	read-write	Link speed configuration on port 2.
INT port3Config	1.3.6.1.4.1.161.19.3.4.3.20	INTEGER	read-write	Link speed configuration on port 3.
INT port4Config	1.3.6.1.4.1.161.19.3.4.3.21	INTEGER	read-write	Link speed configuration on port 4.
INT port5Config	1.3.6.1.4.1.161.19.3.4.3.22	INTEGER	read-write	Link speed configuration on port 5.
INT port6Config	1.3.6.1.4.1.161.19.3.4.3.23	INTEGER	read-write	Link speed configuration on port 6.
INT port7Config	1.3.6.1.4.1.161.19.3.4.3.24	INTEGER	read-write	Link speed configuration on port 7.
INT port8Config	1.3.6.1.4.1.161.19.3.4.3.25	INTEGER	read-write	Link speed configuration on port 8.
STR port1Description	1.3.6.1.4.1.161.19.3.4.3.26	DisplayString	read-write	Port 1 text description.
STR port2Description	1.3.6.1.4.1.161.19.3.4.3.27	DisplayString	read-write	Port 2 text description.
STR port3Description	1.3.6.1.4.1.161.19.3.4.3.28	DisplayString	read-write	Port 3 text description.
STR port4Description	1.3.6.1.4.1.161.19.3.4.3.29	DisplayString	read-write	Port 4 text description.
STR port5Description	1.3.6.1.4.1.161.19.3.4.3.30	DisplayString	read-write	Port 5 text description.
STR port6Description	1.3.6.1.4.1.161.19.3.4.3.31	DisplayString	read-write	Port 6 text description.
STR port7Description	1.3.6.1.4.1.161.19.3.4.3.32	DisplayString	read-write	Port 7 text description.
STR port8Description	1.3.6.1.4.1.161.19.3.4.3.33	DisplayString	read-write	Port 8 text description.
IP snmpTrap1	1.3.6.1.4.1.161.19.3.4.3.34	IpAddress	read-write	SNMP Trap Address 1.
IP snmpTrap2	1.3.6.1.4.1.161.19.3.4.3.35	IpAddress	read-write	SNMP Trap Address 2.
IP snmpTrap3	1.3.6.1.4.1.161.19.3.4.3.36	IpAddress	read-write	SNMP Trap Address 3.
IP snmpTrap4	1.3.6.1.4.1.161.19.3.4.3.37	IpAddress	read-write	SNMP Trap Address 4.
IP snmpTrap5	1.3.6.1.4.1.161.19.3.4.3.38	IpAddress	read-write	SNMP Trap Address 5.
IP snmpTrap6	1.3.6.1.4.1.161.19.3.4.3.39	IpAddress	read-write	SNMP Trap Address 6.
IP snmpTrap7	1.3.6.1.4.1.161.19.3.4.3.40	IpAddress	read-write	SNMP Trap Address 7.
IP snmpTrap8	1.3.6.1.4.1.161.19.3.4.3.41	IpAddress	read-write	SNMP Trap Address 8.
IP snmpTrap9	1.3.6.1.4.1.161.19.3.4.3.42	IpAddress	read-write	SNMP Trap Address 9.
IP snmpTrap10	1.3.6.1.4.1.161.19.3.4.3.43	IpAddress	read-write	SNMP Trap Address 10.
INT vlanTagEnable	1.3.6.1.4.1.161.19.3.4.3.44	INTEGER	read-write	Enable/Disable 802.1Q VLAN tagging.P (1) -- Enable Tagging. (0) -- Disable Tagging.
INT vlanTagId	1.3.6.1.4.1.161.19.3.4.3.45	INTEGER	read-write	802.1q VLAN Tag ID, 1-4095.
INT port1Uplink	1.3.6.1.4.1.161.19.3.4.3.46	INTEGER	read-write	Configure Port 1 as Uplink Port. (1) -- Port 1 is an uplink port. (0) -- Port 1 is not an uplink port.
INT port2Uplink	1.3.6.1.4.1.161.19.3.4.3.47	INTEGER	read-write	Configure Port 2 as Uplink Port. (1) -- Port 2 is an uplink port. (0) -- Port 2 is not an uplink port.
INT port3Uplink	1.3.6.1.4.1.161.19.3.4.3.48	INTEGER	read-write	Configure Port 3 as Uplink Port. (1) -- Port 3 is an uplink port. (0) -- Port 3 is not an uplink port.
INT port4Uplink	1.3.6.1.4.1.161.19.3.4.3.49	INTEGER	read-write	Configure Port 4 as Uplink Port. (1) -- Port 4 is an uplink port. (0) -- Port 4 is not an uplink port.
INT port5Uplink	1.3.6.1.4.1.161.19.3.4.3.50	INTEGER	read-write	Configure Port 5 as Uplink Port. (1) -- Port 5 is an uplink port. (0) -- Port 5 is not an uplink port.
INT port6Uplink	1.3.6.1.4.1.161.19.3.4.3.51	INTEGER	read-write	Configure Port 6 as Uplink Port. (1) -- Port 6 is an uplink port. (0) -- Port 6 is not an uplink port.
INT port7Uplink	1.3.6.1.4.1.161.19.3.4.3.52	INTEGER	read-write	Configure Port 7 as Uplink Port. (1) -- Port 7 is an uplink port. (0) -- Port 7 is not an uplink port.
INT port8Uplink	1.3.6.1.4.1.161.19.3.4.3.53	INTEGER	read-write	Configure Port 8 as Uplink Port. (1) -- Port 8 is an uplink port. (0) -- Port 8 is not an uplink port.
INT rebootIfRequired	1.3.6.1.4.1.161.19.3.4.3.54	INTEGER	read-write	Reboot CMM if required. (1) -- Check if CMM reboot is required and do so. (0) -- Do not check for reboot.
INT port1VlanConf	1.3.6.1.4.1.161.19.3.4.3.55	INTEGER	read-write	Port 1 VLAN Port Configuration. Bitmap determines which Port(s) Port 1 will egress data. 0 means no ports, 2 means port 2, 6 means ports 2 and 3, etc.
INT port2VlanConf	1.3.6.1.4.1.161.19.3.4.3.56	INTEGER	read-write	Port 2 VLAN Port Configuration. Bitmap determines which Port(s) Port 2 will egress data. 0 means no ports, 1 means port 1, 3 means ports 1 and 2, etc.
INT port3VlanConf	1.3.6.1.4.1.161.19.3.4.3.57	INTEGER	read-write	Port 3 VLAN Port Configuration. Bitmap determines which Port(s) Port 3 will egress data. 0 means no ports, 1 means port 1, 3 means ports 1 and 2, etc.
INT port4VlanConf	1.3.6.1.4.1.161.19.3.4.3.58	INTEGER	read-write	Port 4 VLAN Port Configuration. Bitmap determines which Port(s) Port 4 will egress data. 0 means no ports, 1 means port 1, 3 means ports 1 and 2, etc.
INT port5VlanConf	1.3.6.1.4.1.161.19.3.4.3.59	INTEGER	read-write	Port 5 VLAN Port Configuration. Bitmap determines which Port(s) Port 5 will egress data. 0 means no ports, 1 means port 1, 3 means ports 1 and 2, etc.
INT port6VlanConf	1.3.6.1.4.1.161.19.3.4.3.60	INTEGER	read-write	Port 6 VLAN Port Configuration. Bitmap determines which Port(s) Port 6 will egress data. 0 means no ports, 1 means port 1, 3 means ports 1 and 2, etc.
INT port7VlanConf	1.3.6.1.4.1.161.19.3.4.3.61	INTEGER	read-write	Port 7 VLAN Port Configuration. Bitmap determines which Port(s) Port 7 will egress data. 0 means no ports, 1 means port 1, 3 means ports 1 and 2, etc.
INT port8VlanConf	1.3.6.1.4.1.161.19.3.4.3.62	INTEGER	read-write	Port 8 VLAN Port Configuration. Bitmap determines which Port(s) Port 8 will egress data. 0 means no ports, 1 means port 1, 3 means ports 1 and 2, etc.
INT port1PwrReset	1.3.6.1.4.1.161.19.3.4.3.63	INTEGER	read-write	If Port 1 is Powered, attched device will be reset when set to 1. If Port 1 is Not Powered, nothing will happen.
INT port2PwrReset	1.3.6.1.4.1.161.19.3.4.3.64	INTEGER	read-write	If Port 2 is Powered, attched device will be reset when set to 1. If Port 2 is Not Powered, nothing will happen.
INT port3PwrReset	1.3.6.1.4.1.161.19.3.4.3.65	INTEGER	read-write	If Port 3 is Powered, attched device will be reset when set to 1. If Port 3 is Not Powered, nothing will happen.
INT port4PwrReset	1.3.6.1.4.1.161.19.3.4.3.66	INTEGER	read-write	If Port 4 is Powered, attched device will be reset when set to 1. If Port 4 is Not Powered, nothing will happen.
INT port5PwrReset	1.3.6.1.4.1.161.19.3.4.3.67	INTEGER	read-write	If Port 5 is Powered, attched device will be reset when set to 1. If Port 5 is Not Powered, nothing will happen.
INT port6PwrReset	1.3.6.1.4.1.161.19.3.4.3.68	INTEGER	read-write	If Port 6 is Powered, attched device will be reset when set to 1. If Port 6 is Not Powered, nothing will happen.
INT port7PwrReset	1.3.6.1.4.1.161.19.3.4.3.69	INTEGER	read-write	If Port 7 is Powered, attched device will be reset when set to 1. If Port 7 is Not Powered, nothing will happen.
INT port8PwrReset	1.3.6.1.4.1.161.19.3.4.3.70	INTEGER	read-write	If Port 8 is Powered, attched device will be reset when set to 1. If Port 8 is Not Powered, nothing will happen.
cmmStatus	1.3.6.1.4.1.161.19.3.4.4
cmmPortTable	1.3.6.1.4.1.161.19.3.4.4.1		not-accessible	A list of CMM III port entries.
cmmPortEntry	1.3.6.1.4.1.161.19.3.4.4.1.1		not-accessible	A CMM port entry containing objects with port status.
INT portIndex	1.3.6.1.4.1.161.19.3.4.4.1.1.1	INTEGER	read-only	A unique value for each CMM port.
INT linkStatus	1.3.6.1.4.1.161.19.3.4.4.1.1.2	INTEGER	read-only	The current operational state of the port.
INT linkSpeed	1.3.6.1.4.1.161.19.3.4.4.1.1.3	INTEGER	read-only	Network connectivity, 100BaseT or 10BaseT.
INT duplexStatus	1.3.6.1.4.1.161.19.3.4.4.1.1.4	INTEGER	read-only	Half-duplex data transmission or Full-duplex data transmission.
INT powerStatus	1.3.6.1.4.1.161.19.3.4.4.1.1.5	INTEGER	read-only	Port power status indicates power on or power off.
INT uplinkStatus	1.3.6.1.4.1.161.19.3.4.4.1.1.6	INTEGER	read-only	Port Uplink status indicates whether port is configred as an Uplink Port.
STR deviceType	1.3.6.1.4.1.161.19.3.4.4.2	DisplayString	read-only	A textual string containing information about device type.
STR pldVersion	1.3.6.1.4.1.161.19.3.4.4.3	DisplayString	read-only	Version of PLD code.
STR softwareVersion	1.3.6.1.4.1.161.19.3.4.4.4	DisplayString	read-only	CMM-III software version. It includes the operation system and software build time.
STR systemTime	1.3.6.1.4.1.161.19.3.4.4.5	DisplayString	read-only	The current time.
STR upTime	1.3.6.1.4.1.161.19.3.4.4.6	DisplayString	read-only	Time since last system reboot.
STR satellitesVisible	1.3.6.1.4.1.161.19.3.4.4.7	DisplayString	read-only	Number of satellites the GPS should see.
STR satellitesTracked	1.3.6.1.4.1.161.19.3.4.4.8	DisplayString	read-only	Current number of satellites that GPS actually tracks.
STR latitude	1.3.6.1.4.1.161.19.3.4.4.9	DisplayString	read-only	CMM-III latitude.
STR longitude	1.3.6.1.4.1.161.19.3.4.4.10	DisplayString	read-only	CMM-III longitude.
STR height	1.3.6.1.4.1.161.19.3.4.4.11	DisplayString	read-only	The height of CMM-III unit.
STR trackingMode	1.3.6.1.4.1.161.19.3.4.4.12	DisplayString	read-only	CMM-III GPS tracking mode.
STR syncStatus	1.3.6.1.4.1.161.19.3.4.4.13	DisplayString	read-only	CMM-III GPS sync pulse status.
STR macAddress	1.3.6.1.4.1.161.19.3.4.4.14	DisplayString	read-only	MAC address of the unit.
cmmGps	1.3.6.1.4.1.161.19.3.4.5
STR gpsTrackingMode	1.3.6.1.4.1.161.19.3.4.5.1	DisplayString	read-only	CMM-III GPS tracking mode.
STR gpsTime	1.3.6.1.4.1.161.19.3.4.5.2	DisplayString	read-only	CMM-III GPS time.
STR gpsDate	1.3.6.1.4.1.161.19.3.4.5.3	DisplayString	read-only	CMM-III GPS date.
STR gpsSatellitesVisible	1.3.6.1.4.1.161.19.3.4.5.4	DisplayString	read-only	Number of satellites the GPS is supposed to see.
STR gpsSatellitesTracked	1.3.6.1.4.1.161.19.3.4.5.5	DisplayString	read-only	Current number of satellites GPS tracked.
STR gpsHeight	1.3.6.1.4.1.161.19.3.4.5.6	DisplayString	read-only	CMM height.
STR gpsAntennaConnection	1.3.6.1.4.1.161.19.3.4.5.7	DisplayString	read-only	Antenna Connection status.
STR gpsLatitude	1.3.6.1.4.1.161.19.3.4.5.8	DisplayString	read-only	CMM Latitude.
STR gpsLongitude	1.3.6.1.4.1.161.19.3.4.5.9	DisplayString	read-only	CMM longitude.
STR gpsInvalidMsg	1.3.6.1.4.1.161.19.3.4.5.10	DisplayString	read-only	Number of invalid messages.
INT gpsRestartCount	1.3.6.1.4.1.161.19.3.4.5.11	INTEGER	read-only	Number of unit restart.
STR gpsReceiverInfo	1.3.6.1.4.1.161.19.3.4.5.12	DisplayString	read-only	A textual string contains information on GPS receiver.
cmmEventLog	1.3.6.1.4.1.161.19.3.4.6
STR eventLog	1.3.6.1.4.1.161.19.3.4.6.1	EventString	read-only	CMM Event log.
cmmControls	1.3.6.1.4.1.161.19.3.4.7
INT reboot	1.3.6.1.4.1.161.19.3.4.7.1	INTEGER	read-write	Setting the variable to 1 will reboot the unit. When the unit finishs rebooting, it will be in finishedReboot state.
INT clearEventLog	1.3.6.1.4.1.161.19.3.4.7.2	INTEGER	read-write	Setting the variable to 1 will clear the event log.

RFC description

Compaq/HP Compaq Modular Management (CMM3) baseboard management controller MIB for hardware health and blade management.

Start monitoring cable headend hardware modules with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CMM3-MIB