All MIBs › CISCO-VISM-DSX0-MIB
Organization: Cisco Systems, Inc.
Last Updated: 2004-03-11
Category: Cisco Devices, Telephony and VoIP
Description: Manages DS0 channel configuration, signaling, and status for individual time slots on Cisco VISM T1/E1 interfaces.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is CISCO-VISM-DSX0-MIB?
This Cisco private MIB manages DS0 (individual voice timeslot) configuration, signaling, and status on VISM (Voice Interworking Service Module) cards, which carry voice traffic over ATM within Cisco MGX 8250/8850 and related MGX chassis. It exposes per-timeslot signaling configuration (robbed-bit signaling, idle/seized/received codes, CAS variant and cadence) as well as bundle/interface-type mapping and card-level statistics. Its monitoring emphasis is on hardware and software status together: card statistics reflect the health of the VISM hardware module itself, while the per-DS0 signaling codes reveal whether individual voice channels are behaving correctly, so an admin can catch a failing timeslot or a misconfigured CAS variant before it disrupts calls. It builds on the conventions of the standard DS1/T1-E1 interface MIBs, since each DS0 timeslot is a subdivision of a DS1 line. It is deployed within Cisco MGX 8250/8850 voice gateway chassis carrying voice-over-ATM trunks in carrier and enterprise voice networks. Engineers can download the CISCO-VISM-DSX0-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in CISCO-VISM-DSX0-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Cisco VISM (Voice Interworking Service Module)
- Cisco MGX 8850/8250 chassis
Monitoring Examples
An admin would poll dsx0VismCnfTable/dsx0VismCnfEntry, indexed by ds0IfIndex, to check ds0RobbedBitSignalling, ds0IdleCode, ds0SeizedCode, and ds0ReceivedCode for a given timeslot, along with ds0CasVariantName and ds0CasCadenceOnTime for its channel-associated signaling setup. ds0BundleMapped and ds0IfType show whether and how that timeslot is bundled into a voice channel, while vismDs0CardStats gives card-level statistics for the VISM module as a whole. A timeslot reporting an unexpected received code alongside degraded vismDs0CardStats would reveal a failing voice trunk or a misconfigured CAS variant on that card.
What Can Be Monitored
- DS0 timeslot signaling configuration
- channel-associated signaling (CAS) codes
- DS0 bundle/interface type mapping
- VISM card statistics
This MIB depends on
Related MIBs
Imported Objects
From BASIS-MIB
| cardSpecific | OBJECT-IDENTITY |
| dsx0Vism | OBJECT-IDENTITY |
From CISCOWAN-SMI
| ciscoWan | OBJECT-IDENTITY |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Integer32 | |
| MODULE-IDENTITY | |
| OBJECT-TYPE |
From SNMPv2-TC
| DisplayString | |
| TruthValue |
How to Use in IPNetwork Monitor
Example using vismActiveDs0Count OID:
Select a Cisco VISM (Voice Interworking Service Module) card, MGX platform (legacy) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type vismActiveDs0Count into the Find box to locate it in the OID tree, then select it and click OK. This is the number of active ds0s on the card. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is an Integer32-type OID, Value bounds is the most useful condition here — trigger an alert if the count changes from its expected baseline, since that would indicate the underlying set of items changed unexpectedly. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| ciscoVismCardStatsGroup | 1.3.6.1.4.1.351.150.81.2.1.1 | The collection of objects used for DS0 Statistics applicable to VISM Module. | ||
| ciscoVismDsx0ChanMapGroup | 1.3.6.1.4.1.351.150.81.2.1.5 | The collection of objects used for mapping DS0 to ifIndex. | ||
| ciscoVismDsx0Compliance | 1.3.6.1.4.1.351.150.81.2.2.1 | The compliance statement for objects related to DS0 mib objects. | ||
| ciscoVismDsx0Compliance2 | 1.3.6.1.4.1.351.150.81.2.2.2 | The compliance statement for objects related to DS0 mib objects. | ||
| ciscoVismDsx0ConfDeprecatedGroup | 1.3.6.1.4.1.351.150.81.2.1.6 | The collection of objects that were supported earlier but deprecated now. | ||
| ciscoVismDsx0ConfGroup | 1.3.6.1.4.1.351.150.81.2.1.4 | The collection of objects used for DS0 configuration in VISM module. | ||
| ciscoVismDsx0ConfGroup2 | 1.3.6.1.4.1.351.150.81.2.1.7 | The collection of objects used for DS0 configuration in VISM module. | ||
| ciscoVismDsx0LineStatsGroup | 1.3.6.1.4.1.351.150.81.2.1.2 | The collection of objects used for DS0 Line statistics. | ||
| ciscoVismDsx0MIB | 1.3.6.1.4.1.351.150.81 | This MIB module contains ds0 configuration, Status and DS0 related information on a DS1 interface supported in VISM module. VISM is a Voice Interworking Service Module supported in MGX8250 and MGX8850 and other MGX products. Terminologies used: line : Same as the Physical Interface. DS1 line signifies DS1 interface. | ||
| ciscoVismDsx0MIBCompliances | 1.3.6.1.4.1.351.150.81.2.2 | |||
| ciscoVismDsx0MIBConformance | 1.3.6.1.4.1.351.150.81.2 | |||
| ciscoVismDsx0MIBGroups | 1.3.6.1.4.1.351.150.81.2.1 | |||
| ciscoVismDsx0StatusGroup | 1.3.6.1.4.1.351.150.81.2.1.3 | The collection of objects used for DS0 status. | ||
| I32 ds0BundleMapped | 1.3.6.1.4.1.351.110.4.7.1.1.7 | Integer32 | read-only | This object indicates endpoint number as specified by mgEndpointNumber of endpoint table. If it is not associated with any endpoint, then it is set to -1. It should be noted that the endpoint is associated with bearer DS0s only. For signaling channel or DS0 as in the case of CCS channel, there is no endpoint number associated with it and the value is set to -1. |
| I32 ds0CasCadenceOffTime | 1.3.6.1.4.1.351.110.4.7.1.1.11 | Integer32 | read-write | This attribute corresponds to the silence between the digit tones. This object is applicable only for CAS backhaul applications. For trunking application it is not applicable. The value is expresssed in units of milliseconds. From vism2.0.3 release onwards this object can configured in any application, but will be applicable only in non-trunking applications and will be ignored in other applications. |
| I32 ds0CasCadenceOnTime | 1.3.6.1.4.1.351.110.4.7.1.1.10 | Integer32 | read-write | This attribute describes the duration during which the digit tone is generated. This object is applicable only for CAS backhaul applications. For trunking application it is not applicable. The value is expresssed in units of milliseconds. From vism2.0.3 release onwards this object can configured in any application, but will be applicable only in non-trunking applications and will be ignored in other applications. |
| I32 ds0CasDelayImmedStart | 1.3.6.1.4.1.351.110.4.7.1.1.23 | Integer32 | read-write | This timer indicates the time that VISM should wait before outpulsing digits to the PBX after sending an off hook event. This applies only to immediate start protocol. This object cannot be configured if the signaling type for the line to which this ds0 belongs is non cas. For a cas line this object CAN only be configured only after associating this ds0 with an endpoint. This object will be applicable if ds0CasParameterSource has a value of mibValue (2). The allowed range for this object is 10..1000. |
| INT ds0CasDirectionality | 1.3.6.1.4.1.351.110.4.7.1.1.29 | INTEGER | read-write | This object specifies the direction in which CAS calls will be accepted on this endpoint. If this object is set to bidirectional(1): VISM can send and receive calls on this endpoint incoming(2) : calls from the connected PBX will be accepted by VISM on this endpoint. outgoing(3) : VISM will send calls towards the connected PBX and not accept calls from the PBX. The main difference between bidirectional and one-way trunks is the occurrence of glare. On bidirectional trunks, since both VISM and the connected PBX can seize the endpoint at approximately the same time, glare (dual seizure) is likely to occur. The protocol assigned to a bidirectional endpoint should be capable of detecting and resolving glare. Wink-start and delay-dial are examples of protocols capable of glare handling and immediate-start, ground-start and loop-start, of those that cannot. This object cannot be configured if the signaling type for the DS1 line to which this ds0 belongs is non-CAS. For a CAS line, this object can only be configured after associating this ds0 with an endpoint. This means that if no endpoint was added for this Ds0, any configuration set attempt will be rejected, but any get will be allowed. |
| I32 ds0CasFlashMaxMakeTime | 1.3.6.1.4.1.351.110.4.7.1.1.28 | Integer32 | read-write | Flash is a CAS signal generated by users to request special services. The interpretation of the flash depends on the protocol in use. The signal itself is an on-hook followed by an off-hook. This object specifies the maximum duration for the signal to be recognized as a flash by VISM. This duration, expressed in milliseconds, is defined as the elapsed time between the off-to-on-hook transition followed by the on-to-off-hook transition. If the on-hook duration is longer than the value of this object, the signal will be ignored. This object cannot be configured if the signaling type for the line to which this ds0 belongs is non-CAS. For a CAS line, this object can only be configured after associating this ds0 with an endpoint. This means that if no endpoint was added for this Ds0, any configuration set attempt will be rejected, but any get will be allowed. This object will be applicable if ds0CasParameterSource has a value of 'mibvalue'(2). The allowed range for this object is 50..1550. The value of this object should be greater than or equal to ds0CasFlashMinMakeTime. |
| I32 ds0CasFlashMinMakeTime | 1.3.6.1.4.1.351.110.4.7.1.1.27 | Integer32 | read-write | Flash is a CAS signal generated by users to request special services. The interpretation of the flash depends on the protocol in use. The signal itself is an on-hook followed by an off-hook. This object specifies the minimum duration for the signal to be recognized as a flash by VISM. This duration, expressed in milliseconds, is defined as the elapsed time between the off-to-on-hook transition followed by the on-to-off-hook transition. If the on-hook duration is shorter than the value of this object, the signal will be ignored. This object cannot be configured if the signaling type for the line to which this ds0 belongs is non-CAS. For a CAS line, this object can only be configured after associating this ds0 with an endpoint. If no endpoint was added for this Ds0, any configuration attempt will be rejected. This object will be applicable if ds0CasParameterSource has a value of mibvalue (2). The allowed range for this object is 50..1550. |
| I32 ds0CasGaurdTime | 1.3.6.1.4.1.351.110.4.7.1.1.22 | Integer32 | read-write | The gaurd time is the duration between the end of one call and the start of next call. This object specifies what should be such a duration. All state changes from the PBX are ignored for this duration. After receiving DLCX, this timer will be started for a period as configured in this object, and will not honor any off-hook events before the expiration of this timer. This object cannot be configured if the signaling type for the line to which this ds0 belongs is non cas. For a cas line this object CAN only be configured only after associating this ds0 with an endpoint This object will be applicable if ds0CasParameterSource has a value of mibValue (2). The allowed range for this object is 10..1000. |
| INT ds0CasGlarePolicy | 1.3.6.1.4.1.351.110.4.7.1.1.30 | INTEGER | read-write | This object specifies how a bidirectional endpoint should resolve glare. This object will be used only if dsx0VismDirectionality of the endpoint is 'bidirectional'. When glare is detected, if this object is set to controlling, VISM will wait for the connected PBX to assert on-hook. When the connected PBX goes on-hook, VISM proceeds to dial the numbers out waits for answer. If this object is set to releasing(2), VISM indicates the glare situation to the Call Agent (as specified by the control protocol), prepares to collect digits from the PBX and asserts on hook. The incoming call should go through. If the CAS protocol assigned to the endpoint cannot detect glare or if it cannot resolve glare according to the policy provisioned via this object, this object will not be used. This object cannot be configured if the signaling type for the DS1 line to which this ds0 belongs is non-CAS. For a CAS line, this object can only be configured after associating this ds0 with an endpoint. This means that if no endpoint was added for this Ds0, any configuration set attempt will be rejected, but any get will be allowed. |
| I32 ds0CasGlareTime | 1.3.6.1.4.1.351.110.4.7.1.1.21 | Integer32 | read-write | When the terminating gateway receives off Hook event from the Call Agent it starts the timer specified in this object to see if the terminating side is also trying to originate a call. If this is true, we have a 'glare' condition. The way glare is resolved is thru this user programmable timer, we will not honor any off hook events from the originating PBX during this time. This object cannot be configured if the signaling type for the line to which this ds0 belongs is non CAS. For a CAS line this object can only be configured only after associating this ds0 with an endpoint This object will be applicable if ds0CasParameterSource has a value of mibValue (2). The allowed range for this object is 10..10000. |
| STR ds0CasIncomingMgcpPackage | 1.3.6.1.4.1.351.110.4.7.1.1.31 | DisplayString | read-write | This object, in conjunction with the card level persistentXgcpEventsTable, controls how persistent CAS events (like seize, disconnect, etc) related to an incoming call observed on this DS0 are notified to the Media Gateway Controller (MGC). At the card level, the persistentXgcpEventsTable allows MGCP package-event combinations to be configured as persistent. For example, when L/hd is added to the persistentXgcpEventsTable, the hook-down event in line package will be notified to the MGC every time it is observed without the MGC requesting for that event. Since the same CAS event can map to different MGCP events under different packages (eg. the CAS event 'seize' can be 'sup' in 'MS' package and 'hd' in 'BL' package) and different lines could be running different packages at a given time, there needs to be a per-DS0 object indicating what package should be used while notifying CAS events observed on that DS0. This object, ds0CasIncomingMgcpPackage specifies the package that will be used while notifying CAS events observed on an incoming call on this DS0. This object can be set to a package name from xgcpCapabilityPackageTable whose xgcpCapabilityPackageEnable is true or the string 'basic' indicating that one of the basic packages in that table (G, T, L, H, R, D or M) to which the observed event belongs can be used. This object is used only if the protocol is MGCP. If the notification is in response to an RQNT, VISM uses the package (and event name) that the MGC used to request the event regardless what this object is set to. In the absence of an RQNT, the observed CAS event is encoded according to the package that this object specifies. A 'seize' observed on the CAS signaling channel on this DS0, for example is encoded as 'ms/sup' if this object is set to 'ms', 'bl/hd' if this object is set to 'bl' or as 'L/hd' if this object is set to 'basic'. If this package/event is present in persistentXgcpEventsTable, a notification is generated, otherwise this event is discarded. An attempt to set this object to a package name whose xgcpCapabilityPackageEnable is false in xgcpCapabilityPackageTable will fail. This object is used only if the ds0CasDirectionality is set to 'bidirectional' or 'incoming'. |
| I32 ds0CasMinDelayDialTime | 1.3.6.1.4.1.351.110.4.7.1.1.25 | Integer32 | read-write | This is an object for an E & M signaling protocol like wink-start for this ds0. The difference is that the address-control signal is different from wink. The originating VISM, on receiving a seize (AB=11) from the PBX, responds by sending the delay-dial (AB=11) signal back to the PBX. When the originating VISM is ready to collect the digits, it sends a start-dial (AB=00) signal. This operation is symmetric. So the terminating VISM, on seizing a trunk, should receive AB=11 (as an ack that the trunk is operational). Subsequently, when it receives the start signal (AB=00) from the connected PBX, it should outpulse the digits. The rest of the operation is similiar to wink-start. The allowed range for this object is 100..1000 with units in milliseconds. In delay-dial operation, the outgoing interface (this interface), after sending a seize signal (AB = 11), waits for the delay-dial signal (AB = 11). The delay-dial signal, apart from acknowledging the seize signal, tells this interface that the connected equipment is not ready for the digits yet. This object specifies the time in milliseconds, after which incoming AB=11 will be interpreted by this interface as the delay-dial signal. |
| I32 ds0CasMinStartDialTime | 1.3.6.1.4.1.351.110.4.7.1.1.26 | Integer32 | read-write | This is an object for an E & M signaling protocol like wink-start for this ds0. The difference is that the address-control signal is different from wink. The originating VISM, on receiving a seize (AB=11) from the PBX, responds by sending the delay-dial (AB=11) signal back to the PBX. When the originating VISM is ready to collect the digits, it sends a start-dial (AB=00) signal. This operation is symmetric. So the terminating VISM, on seizing a trunk, should receive AB=11 (as an ack that the trunk is operational). Subsequently, when it receives the start signal (AB=00) from the connected PBX, it should outpulse the digits. The rest of the operation is similiar to wink-start. The allowed range for this object is 70..1000. In delay-dial operation, the outgoing interface (this interface), after receiving a delay-dial signal (AB=11) from the connected equipment, waits for the start-dial signal (AB = 00) before sending the digits to the connected equipment. The start-dial signal tells this interface that the connected equipment is ready for the digits. This object specifies the time in milliseconds, after which incoming AB=00 will be interpreted by this interface as the start dial signal. |
| I32 ds0CasOffHookMinMakeTime | 1.3.6.1.4.1.351.110.4.7.1.1.17 | Integer32 | read-write | This indicates the minimum time in msecs for which the off hook pattern should be present in order for it to be recognised else the signal will be considered to be a spurious signal and will be ignored. This object cannot be configured if the signaling type for the line to which this ds0 belongs is non cas. For a cas line this object CAN only be configured only after associating this ds0 with an endpoint This object will be applicable if ds0CasParameterSource has a value of mibValue (2). The allowed range for this object is 10..1000 |
| I32 ds0CasOnHookMinMakeTime | 1.3.6.1.4.1.351.110.4.7.1.1.16 | Integer32 | read-write | This indicates the the minimum time in msecs for which the on hook pattern should be present in order for it to be recognised else the signal will be considered to be a spurious signal and will be ignored. This object cannot be configured if the signaling type for the line to which this ds0 belongs is non cas. For a cas line this object CAN only be configured only after associating this ds0 with an endpoint. This object will be applicable if ds0CasParameterSource has a value of mibValue (2). The allowed range for this object is 10..1000 |
| STR ds0CasOutgoingMgcpPackage | 1.3.6.1.4.1.351.110.4.7.1.1.32 | DisplayString | read-write | This object, in conjunction with the card level persistentXgcpEventsTable, controls how persistent CAS events (like answer, disconnect, etc) related to an outgoing call observed on this DS0 are notified to the Media Gateway Controller (MGC). At the card level, the persistentXgcpEventsTable allows MGCP package-event combinations to be configured as persistent. For example, when L/hd is added to the persistentXgcpEventsTable, the hook-down event in line package will be notified to the MGC every time it is observed without the MGC requesting for that event. Since the same CAS event can map to different MGCP events under different packages (eg. the CAS event 'answer' can be 'ans' in 'MS' package and 'hd' in 'BL' package) and different lines could be running different packages at a given time, there needs to be a per-DS0 object indicating what package should be used while notifying CAS events observed on that DS0. This object, ds0CasOutgoingMgcpPackage specifies the package that will be used while notifying CAS events observed on an outgoing call on this DS0. This object can be set to a package name from xgcpCapabilityPackageTable whose xgcpCapabilityPackageEnable is true or the string 'basic' indicating that one of the basic packages in that table (G, T, L, H, R, D or M) to which the observed event belongs can be used. This object is used only if the protocol is MGCP. If the notification is in response to an RQNT, VISM uses the package (and event name) that the MGC used to request the event regardless what this object is set to. In the absence of an RQNT, the observed CAS event is encoded according to the package that this object specifies. An answer observed on the CAS signaling channel on this DS0, for example is encoded as 'ms/ans' if this object is set to 'ms', 'bl/hd' if this object is set to 'bl' or as 'L/hd' if this object is set to 'basic'. If this package/event is present in persistentXgcpEventsTable, a notification is generated, otherwise this event is discarded. An attempt to set this object to a package name whose xgcpCapabilityPackageEnable is false in xgcpCapabilityPackageTable will fail. This object is used only if the ds0CasDirectionality is set to 'bidirectional' or 'outgoing'. |
| INT ds0CasParameterSource | 1.3.6.1.4.1.351.110.4.7.1.1.15 | INTEGER | read-write | This object indicates VISM whether to read the cas related timer parameters from the casAppl file downloaded for that endpoint or to read from this mib. This gives the flexibility of configuring different cas related timer values for different endpoints associated with the same cas variant. This object cannot be configured if the signaling type for the line to which this ds0 belongs is non cas. For a cas line this object CAN only be configured only after associating this ds0 with an endpoint. |
| STR ds0CasVariantName | 1.3.6.1.4.1.351.110.4.7.1.1.9 | DisplayString | read-write | This object indicates the index to the CAS variant table. This parameter can be configured after configuring this ds0 as an endpoint. This object cannot be modified while connections exist on this endpoint. The CAS variant table is used for configuring the system parameters associated with various types of CAS signaling methods supported. |
| I32 ds0CasWinkBreakTime | 1.3.6.1.4.1.351.110.4.7.1.1.20 | Integer32 | read-write | The wink consists of off-hook A-B bit pattern, followed by on-hook A-B bit pattern in timed sequence. This object indicates the minimum duration for which the on-hook part of wink signal should persist. This object cannot be configured if the signaling type for the line to which this ds0 belongs is non cas. For a cas line this object CAN only be configured only after associating this ds0 with an endpoint This object will be applicable if ds0CasParameterSource has a value of mibValue (2). The allowed range for this object is 10..1000. |
| I32 ds0CasWinkMaxMakeTime | 1.3.6.1.4.1.351.110.4.7.1.1.19 | Integer32 | read-write | The wink consists of off-hook A-B bit pattern, followed by on-hook A-B bit pattern in timed sequence. This object indicates the maximum duration for which the off-hook part of the wink signal should persist, if it exceeds this time limit the signal will be considered to be spurious and will be ignored. This object cannot be configured if the signaling type for the line to which this ds0 belongs is non cas. For a cas line this object CAN only be configured only after associating this ds0 with an endpoint This object will be applicable if ds0CasParameterSource has a value of mibValue (2). The allowed range for this object is 10..3000. The value for this object should be greater than or equal to ds0CasWinkMinMakeTime |
| I32 ds0CasWinkMinMakeTime | 1.3.6.1.4.1.351.110.4.7.1.1.18 | Integer32 | read-write | The wink consists of off-hook A-B bit pattern, followed by on-hook A-B bit pattern in timed sequence. This object indicates the minimum duration for which the off-hook part of wink signal should persist. This object cannot be configured if the signaling type for the line to which this ds0 belongs is non cas. For a cas line this object CAN only be configured only after associating this ds0 with an endpoint This object will be applicable if ds0CasParameterSource has a value of mibValue (2). The allowed range for this object is 10..1000. |
| I32 ds0ChanMapIfIndex | 1.3.6.1.4.1.351.110.4.7.2.1.3 | Integer32 | read-only | This object describes the ifIndex derived based on the line number and the channel number within the line according to the formula: IfIndex = 31 * (Ds1# - 1) + ds0# where : Ds1# - The T1/E1 line number in the range 1 - 8. ds0# - The ds0 channel number ranging from 1 to 24 for T1 and 1 to 31 for E1. |
| I32 ds0ChanNum | 1.3.6.1.4.1.351.110.4.7.2.1.2 | Integer32 | read-only | This object describes the ds0 number or channel number within a T1 or E1 line. The valid channel numbers are 1 to 24 for T1 line and 1 - 31 for E1 line. |
| INT ds0Companding | 1.3.6.1.4.1.351.110.4.7.1.1.38 | INTEGER | read-write | This object indicates whether input from / output to the TDM side of DS0 is u-law or a-law stream. The setting of this object will not take effect unless the corresponding DSP channel is closed and re-opened. |
| T/F ds0ExecDiag | 1.3.6.1.4.1.351.110.4.7.1.1.37 | TruthValue | read-write | This object indicates the status of DSP channel level RAS on the VISM. When it is enable VISM will configure the DSP through HOST-DSP message on the individual channel. |
| I32 ds0IdleCode | 1.3.6.1.4.1.351.110.4.7.1.1.3 | Integer32 | read-write | This object contains the code transmitted in the ABCD bits when the ds0 is not connected and ds0TransmitCodesEnable is enabled. The object is a bitmap and the various bit positions are: Bit 0 (value 1) D bit Bit 1 (value 2) C bit Bit 2 (value 4) B bit Bit 3 (value 8) A bit This object is useful for ds0 conditioning to be done if an alarm condition is detected from the network side. DS0 conditioning is implemented in the trunking application only. This object is not applicable in the CAS backhaul application. From vism 2.0.3 release onwards this object can be configured in any mode, but will be applicable only in trunking application and will be ignored in other applications. |
| I32 ds0IfIndex | 1.3.6.1.4.1.351.110.4.7.1.1.1 | Integer32 | read-only | This attribute defines the index for this table. This is derived from the following formula: index = 31 * (Ds1# - 1) + ds0# where : Ds1# - The T1/E1 line number in the range 1 - 8. ds0# - The ds0 channel number ranging from 1 to 24 for T1 and 1 to 31 for E1. |
| INT ds0IfType | 1.3.6.1.4.1.351.110.4.7.1.1.8 | INTEGER | read-only | This object indicates the interface type associated with the ds0. bearer(81) : ds0 ifType is considered as bearer if the DS0 is used for carrying voice traffic. ccs-signaling(63): ds0 ifType is considered as ccs-signaling, if the DS0 is configured as the D-channel. |
| I32 ds0InputGain | 1.3.6.1.4.1.351.110.4.7.1.1.33 | Integer32 | read-write | This object indicates the amount of gain inserted at the receiver side of a ds0 channel, in dB (decibel) units. The default value of this object is 0 dB. The input gain settings only define a gain/loss relative to the 0 dB setting. The absolute loss at the 0 dB setting could be implementation dependent based on the desired network loss plan. This object can be set when there are active call going on, and in this case the new gain will take effective immediately. It can also be set at both unbound endpoints and bound but non-active endpoints. |
| T/F ds0InsertLocalCas | 1.3.6.1.4.1.351.110.4.7.1.1.12 | TruthValue | read-write | This object tells the framer whether to force the cas bits to a value defined by ds0LocalCasPattern or not. If this is enabled the framer will force the cas (ABCD) bits to a value defined in ds0LocalCasPattern by ignorning the cas bits sent by DSP. Else the framer will transmit the cas bits sent by DSP. Setting of this object is not allowed when the signaling type of this line is cas. Also setting of this object is not allowed when the ds0LoopbackCommand is set to RemoteLoop, because in this situation we are suppose to loopback whatever comes from the TDM side and not force the cas bits to something else. This object can be set only if the line type is T1. |
| I32 ds0LineNum | 1.3.6.1.4.1.351.110.4.7.3.1.1 | Integer32 | read-only | This object is the identifier of a DS1/E1 Interface on a managed device. The number of entries is 8 in a VISM and VISM-PR card. |
| I32 ds0LineNumber | 1.3.6.1.4.1.351.110.4.7.4.1.1 | Integer32 | read-only | This object is the identifier of a DS1/E1 Interface on a managed device. The number of entries is 8 in a VISM and VISM-PR card. |
| I32 ds0LocalCasPattern | 1.3.6.1.4.1.351.110.4.7.1.1.13 | Integer32 | read-write | This object contains the pattern that the cas (ABCD) bits will have when ds0InsertLocalCas is enabled. |
| INT ds0LoopbackCommand | 1.3.6.1.4.1.351.110.4.7.1.1.14 | INTEGER | read-write | This object represents the loopback type at the ds0 level.The ds0 configuration overrides the line level configuration. NoLoop There is no loopback on this ds0. LocalLoop The data received from the ATM side is loopedback to the ATM side. RemoteLoop The data from the TDM side is looped back to the TDM side. Setting of this object to RemoteLoop will not be allowed when insert local cas for this ds0 (ds0InsertLocalCas object) is enabled as we are suppose to force the cas bits to the pattern configured in ds0LocalCasPattern, and not do loopback on the TDM side. |
| I32 ds0MusicThreshold | 1.3.6.1.4.1.351.110.4.7.1.1.35 | Integer32 | read-write | The indicates Music On Hold Threshold in dBm. Based on this value, VISM DSP will interprete the incoming signal from TDM side as either silence or voice, and consequently turn on or off VAD. This object can be set when there is active call going on at the ds0 channel, and at both unbound endpoints and bound non-active endpoints. |
| I32 ds0Number | 1.3.6.1.4.1.351.110.4.7.4.1.2 | Integer32 | read-only | This object identifies the ds0 number on a DS1 interface. |
| I32 ds0OutputAttenuation | 1.3.6.1.4.1.351.110.4.7.1.1.34 | Integer32 | read-write | This object contains the amount of attenuation inserted at the transmit side of a ds0 channel, in dB (decibel) units. The output attenuation settings only define a loss relative to 0 dB setting. The absolute loss at the 0 dB setting could be implementation dependent based on the desired network loss plan. This object can be set when there are active call going on, and in this case the new gain will take effective immediately. It can also be set at both unbound endpoints and bound but non-active endpoints. |
| I32 ds0ReceivedCode | 1.3.6.1.4.1.351.110.4.7.1.1.5 | Integer32 | read-only | This object contains the code being received in the ABCD bits. The object is a bitmap and the various bit positions are: Bit 0 (value 1) D bit Bit 1 (value 2) C bit Bit 2 (value 4) B bit Bit 3 (value 8) A bit |
| T/F ds0RobbedBitSignalling | 1.3.6.1.4.1.351.110.4.7.1.1.2 | TruthValue | read-write | This object indicates if Robbed Bit Signalling is turned on or off for a given ds0. This only applies to DS0s on a DS1 link. For E1 links the value is always off (false). For T1 links, the default value is true if the line is configured for CAS signaling, the default value is false if the line is configured for CCS signaling or no signaling. |
| STR ds0RxCasTransTblName | 1.3.6.1.4.1.351.110.4.7.1.1.39 | DisplayString | read-write | This object identifies the template name 'cvcmCasTemplateName' in the CISCO-VOICE-CAS-MODULE-MIB associated with the receive signaling channel on a DS0. |
| I32 ds0SeizedCode | 1.3.6.1.4.1.351.110.4.7.1.1.4 | Integer32 | read-write | This object contains the code transmitted in the ABCD bits when the ds0 is connected and ds0TransmitCodesEnable is enabled. The object is a bitmap and the various bit positions are: Bit 0 (value 1) D bit Bit 1 (value 2) C bit Bit 2 (value 4) B bit Bit 3 (value 8) A bit This object is useful for ds0 conditioning to be done if an alarm condition is detected from the network side. DS0 conditioning is implemented in the trunking application only. This object is not applicable in the CAS backhaul application. From vism 2.0.3 release onwards this object can be configured in any mode, but will be applicable only in trunking application and will be ignored in other applications. |
| T/F ds0SidPacket | 1.3.6.1.4.1.351.110.4.7.1.1.36 | TruthValue | read-write | This object specifies whether the Silence Indication Detection (SID) packet should be generated when silence suppression is in active mode. The SID packet indicates the noise level during silence, which is used as a reference to generate comfort noise on the other side of the gateway. This object is used for VoIP only. |
| INT ds0SignalingType | 1.3.6.1.4.1.351.110.4.7.1.1.24 | INTEGER | read-only | This attribute indicates the type of signaling on the line to which this ds0 belongs. CAS - Channel Associated Signaling CCS - Common Channel Signaling none - no signaling used. This object will be implicitly set to line signaling type every time it changes. |
| INT ds0Status | 1.3.6.1.4.1.351.110.4.7.4.1.3 | INTEGER | read-only | This object is the status of the ds0. idle - This ds0 is in idle state. busy - This ds0 is in busy state. Ds0 enters this state when it is in the process of being setup for a call. fault - This ds0 is in fault(alarm) state. block - This ds0 is in block state. Ds0 can enter this state when the line or gateway is commissioned out of service. |
| INT ds0StatusClrButton | 1.3.6.1.4.1.351.110.4.7.4.1.4 | INTEGER | read-write | This variable is used to clear the vism Ds0 status. 1 = No action, 2 = Clear alarm |
| T/F ds0TransmitCodesEnable | 1.3.6.1.4.1.351.110.4.7.1.1.6 | TruthValue | read-only | This object determines if the idle and seized codes are transmitted. If the value of this object is true then the codes are transmitted. This object is not applicable in the CAS backhaul application. |
| STR ds0TxCasTransTblName | 1.3.6.1.4.1.351.110.4.7.1.1.40 | DisplayString | read-write | This object identifies the template name 'cvcmCasTemplateName' in the CISCO-VOICE-CAS-MODULE-MIB associated with the transmit signaling channel on a DS0. |
| INT ds0TxRxCasConfig | 1.3.6.1.4.1.351.110.4.7.1.1.41 | INTEGER | read-write | This object indicates configuration on a DS0. 'transmit'- Configure transmit signaling channel on the DSP with user defined CAS pattern to translate incoming ABCD CAS bits from the TDM 'receive'- Configure receive signaling channel on the DSP with user defined CAS pattern to translate the outgoing ABCD CAS bits on the TDM 'bidirectional'- Configure transmit and receive signaling channel on the DSP with user defined CAS pattern to translate incoming and outgoing ABCD CAS bits on the TDM 'none'- Signaling channel is using default ABCD CAS pattern specified by the DSP. |
| dsx0VismChanMapEntry | 1.3.6.1.4.1.351.110.4.7.2.1 | not-accessible | Each entry represents the mapping from dsx1Line number to ds0 channel Number and provides the ifIndex mapping. | |
| dsx0VismChanMapTable | 1.3.6.1.4.1.351.110.4.7.2 | not-accessible | This table is created implicitly at the time of creating and deleting the endpoints. This table provides the mapping information from a line and channel to obtain an index for that channel. | |
| dsx0VismCnfEntry | 1.3.6.1.4.1.351.110.4.7.1.1 | not-accessible | This ds0 table contains both cas related and non cas related parameters. The non cas related parameters are applicable accross all line signaling types, while the following cas related parameters are applicable only if the signaling type of the line(DS1/E1 Interface) to which this ds0 belongs is cas. ds0IdleCode ds0SeizedCode ds0ReceivedCode ds0CasVariantName ds0CasCadenceOnTime ds0CasCadenceOffTime ds0InsertLocalCas ds0LocalCasPattern ds0CasParameterSource ds0CasOnHookMinMakeTime ds0CasOffHookMinMakeTime ds0CasWinkMinMakeTime ds0CasWinkMaxMakeTime ds0CasWinkBreakTime ds0CasGlareTime ds0CasGaurdTime ds0CasDelayImmedStart ds0CasMinDelayDialTime ds0CasMinStartDialTime ds0CasFlashMinMakeTime ds0CasFlashMaxMakeTime ds0CasDirectionality ds0CasGlarePolicy ds0CasIncomingMgcpPackage ds0CasOutgoingMgcpPackage When the line signaling type changes from cas to non-cas and vice versa, then the user will be forced to delete endpoint/ccs channels associated with any ds0 on that line When an endpoint is deleted the ds0CasVariantName associated with that endpoint will also be implicitly deleted. Other than that none of the above cas related parameters are modified across line signaling type changes. | |
| dsx0VismCnfTable | 1.3.6.1.4.1.351.110.4.7.1 | not-accessible | The entries in this table are created and deleted implicitly at the time of adding and deleting the line. For every DS0 on a line, one row will be created. | |
| I32 dsx1LineNum | 1.3.6.1.4.1.351.110.4.7.2.1.1 | Integer32 | read-only | This object describes the physical line number on VISM card. |
| I32 lineActiveDs0Count | 1.3.6.1.4.1.351.110.4.7.3.1.4 | Integer32 | read-only | This is the number of active ds0s on this line. |
| I32 lineActiveHighWaterMark | 1.3.6.1.4.1.351.110.4.7.3.1.6 | Integer32 | read-only | This is the high water mark number of ds0s that were active simultaneously on the line. |
| I32 lineBlockDs0Count | 1.3.6.1.4.1.351.110.4.7.3.1.5 | Integer32 | read-only | This is the number of blocked ds0s on this line. |
| I32 lineFreeDs0Count | 1.3.6.1.4.1.351.110.4.7.3.1.3 | Integer32 | read-only | This is the total number of free ds0s on this DS1 line. |
| INT lineStatsClrButton | 1.3.6.1.4.1.351.110.4.7.3.1.7 | INTEGER | read-write | This variable is used to clear the vism Ds0 line status entry. 1 = No action, 2 = Clear alarm. |
| I32 lineTotalDs0Count | 1.3.6.1.4.1.351.110.4.7.3.1.2 | Integer32 | read-only | This is the total number of ds0s configured on this DS1 line. |
| I32 vismActiveDs0CountEx | 1.3.6.1.4.1.351.110.3.24.3 | Integer32 | read-only | This is the number of active ds0s on the card. |
| I32 vismActiveHighWaterMark | 1.3.6.1.4.1.351.110.3.24.5 | Integer32 | read-only | This is the high water mark number of ds0s that were active simultaneously on the card. |
| I32 vismBlockDs0Count | 1.3.6.1.4.1.351.110.3.24.4 | Integer32 | read-only | This is the number of blocked ds0s on the card. |
| vismDs0CardStats | 1.3.6.1.4.1.351.110.3.24 | |||
| INT vismDs0CardStatsClrButton | 1.3.6.1.4.1.351.110.3.24.6 | INTEGER | read-write | This variable is used to clear all the vism Ds0 card stats. 1 = No action, 2 = Clear alarm |
| vismDs0LineStatsEntry | 1.3.6.1.4.1.351.110.4.7.3.1 | not-accessible | An entry in the vismDs0LineStatsTable. Each entry contains following information applicable for each DS1 interface: Total DS0s Free DS0s Active DS0s Blocked DS0s. | |
| vismDs0LineStatsTable | 1.3.6.1.4.1.351.110.4.7.3 | not-accessible | This table contains information on DS0s configured on DS1 interface. | |
| vismDs0StatusEntry | 1.3.6.1.4.1.351.110.4.7.4.1 | not-accessible | An entry in the Ds0 Status Table. | |
| vismDs0StatusTable | 1.3.6.1.4.1.351.110.4.7.4 | not-accessible | This table contains ds0 status information on a DS1 interface. | |
| I32 vismFreeDs0Count | 1.3.6.1.4.1.351.110.3.24.2 | Integer32 | read-only | This is the number of free ds0s on the card. |
| I32 vismTotalDs0Count | 1.3.6.1.4.1.351.110.3.24.1 | Integer32 | read-only | This is the total number of ds0s configured the card. |
RFC description
Manages DS0 interface configuration and alarms for voice interworking in Cisco MGX voice interface modules.
Start monitoring Cisco VISM (Voice Interworking Service Module) card, MGX platform (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.