All MIBs › CISCO-VISM-DSX0-MIB › ds0CasFlashMaxMakeTime
ds0CasFlashMaxMakeTime
Module: CISCO-VISM-DSX0-MIB
OID (symbolic): CISCO-VISM-DSX0-MIB::ds0CasFlashMaxMakeTime
OID (numeric): 1.3.6.1.4.1.351.110.4.7.1.1.28
Node type: OBJECT-TYPE
Type: Integer32
Access: read-write
Description: Flash is a CAS signal generated by users to request special services. The interpretation of the flash depends on the protocol in use. The signal itself is an on-hook followed by an off-hook. This object specifies the maximum duration for the signal to be recognized as a flash by VISM. This duration, expressed in milliseconds, is defined as the elapsed time between the off-to-on-hook transition followed by the on-to-off-hook transition. If the on-hook duration is longer than the value of this object, the signal will be ignored.
This object cannot be configured if the signaling type for the line to which this ds0 belongs is non-CAS.
For a CAS line, this object can only be configured after associating this ds0 with an endpoint. This means that if no endpoint was added for this Ds0, any configuration set attempt will be rejected, but any get will be allowed.
This object will be applicable if ds0CasParameterSource has a value of 'mibvalue'(2).
The allowed range for this object is 50..1550. The value of this object should be greater than or equal to ds0CasFlashMinMakeTime.
What is ds0CasFlashMaxMakeTime?
This Integer32 (in milliseconds) sets the maximum duration of the on-hook/off-hook flash sequence that VISM will still recognize as a flash rather than a full hangup on this DS0. This upper bound prevents a genuine slow hangup-and-redial from being misinterpreted as a flash-hook request for a special service. For instance, an admin might lower ds0CasFlashMaxMakeTime if users are experiencing accidental flash-triggered transfers when they briefly hang up and pick back up.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.351.110.4.7.1.1.28 snmpwalk -v2c -c public <target> CISCO-VISM-DSX0-MIB::ds0CasFlashMaxMakeTime
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.351.110.4.7.1.1.28.1 snmpget -v2c -c public <target> CISCO-VISM-DSX0-MIB::ds0CasFlashMaxMakeTime.1
Set instance 1 (SNMPv2c):
snmpset -v2c -c private <target> 1.3.6.1.4.1.351.110.4.7.1.1.28.1 i <value>
Start monitoring Cisco VISM (Voice Interworking Service Module) card, MGX platform (legacy) with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the CISCO-VISM-DSX0-MIB::ds0CasFlashMaxMakeTime OID value, configure state conditions and alerts, and monitor any Cisco VISM (Voice Interworking Service Module) card, MGX platform (legacy) from a single console.
OID Breakdown
Upper-level ancestors (10 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.351 | stratacom | CISCOWAN-SMI |
| 1.3.6.1.4.1.351.110 | basis | BASIS-MIB |
| 1.3.6.1.4.1.351.110.4 | basisLines | BASIS-MIB |
| 1.3.6.1.4.1.351.110.4.7 | dsx0Vism | BASIS-MIB |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.351.110.4.7.1 | dsx0VismCnfTable | CISCO-VISM-DSX0-MIB |
| 1.3.6.1.4.1.351.110.4.7.1.1 | dsx0VismCnfEntry | CISCO-VISM-DSX0-MIB |
| 1.3.6.1.4.1.351.110.4.7.1.1.28 | ds0CasFlashMaxMakeTime | CISCO-VISM-DSX0-MIB |