All MIBs › CISCO-VISM-DSX0-MIB › ds0CasFlashMinMakeTime
ds0CasFlashMinMakeTime
Module: CISCO-VISM-DSX0-MIB
OID (symbolic): CISCO-VISM-DSX0-MIB::ds0CasFlashMinMakeTime
OID (numeric): 1.3.6.1.4.1.351.110.4.7.1.1.27
Node type: OBJECT-TYPE
Type: Integer32
Access: read-write
Description: Flash is a CAS signal generated by users to request special services. The interpretation of the flash depends on the protocol in use. The signal itself is an on-hook followed by an off-hook. This object specifies the minimum duration for the signal to be recognized as a flash by VISM. This duration, expressed in milliseconds, is defined as the elapsed time between the off-to-on-hook transition followed by the on-to-off-hook transition. If the on-hook duration is shorter than the value of this object, the signal will be ignored.
This object cannot be configured if the signaling type for the line to which this ds0 belongs is non-CAS. For a CAS line, this object can only be configured after associating this ds0 with an endpoint. If no endpoint was added for this Ds0, any configuration attempt will be rejected.
This object will be applicable if ds0CasParameterSource has a value of mibvalue (2).
The allowed range for this object is 50..1550.
What is ds0CasFlashMinMakeTime?
This Integer32 (in milliseconds) sets the minimum duration of an on-hook-then-off-hook transition sequence required for VISM to recognize it as a flash signal on this DS0. Flash is used by end users to request special services like call transfer or hold, so this threshold determines how deliberate a hook-flash gesture must be before the gateway acts on it. For example, if users report that flash-hook features like call transfer aren't triggering, an admin might check whether their flash gesture duration falls below ds0CasFlashMinMakeTime.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.351.110.4.7.1.1.27 snmpwalk -v2c -c public <target> CISCO-VISM-DSX0-MIB::ds0CasFlashMinMakeTime
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.351.110.4.7.1.1.27.1 snmpget -v2c -c public <target> CISCO-VISM-DSX0-MIB::ds0CasFlashMinMakeTime.1
Set instance 1 (SNMPv2c):
snmpset -v2c -c private <target> 1.3.6.1.4.1.351.110.4.7.1.1.27.1 i <value>
Start monitoring Cisco VISM (Voice Interworking Service Module) card, MGX platform (legacy) with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the CISCO-VISM-DSX0-MIB::ds0CasFlashMinMakeTime OID value, configure state conditions and alerts, and monitor any Cisco VISM (Voice Interworking Service Module) card, MGX platform (legacy) from a single console.
OID Breakdown
Upper-level ancestors (10 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.351 | stratacom | CISCOWAN-SMI |
| 1.3.6.1.4.1.351.110 | basis | BASIS-MIB |
| 1.3.6.1.4.1.351.110.4 | basisLines | BASIS-MIB |
| 1.3.6.1.4.1.351.110.4.7 | dsx0Vism | BASIS-MIB |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.351.110.4.7.1 | dsx0VismCnfTable | CISCO-VISM-DSX0-MIB |
| 1.3.6.1.4.1.351.110.4.7.1.1 | dsx0VismCnfEntry | CISCO-VISM-DSX0-MIB |
| 1.3.6.1.4.1.351.110.4.7.1.1.27 | ds0CasFlashMinMakeTime | CISCO-VISM-DSX0-MIB |