All MIBs › CISCO-VISM-DSX0-MIB › ds0CasDelayImmedStart
ds0CasDelayImmedStart
Module: CISCO-VISM-DSX0-MIB
OID (symbolic): CISCO-VISM-DSX0-MIB::ds0CasDelayImmedStart
OID (numeric): 1.3.6.1.4.1.351.110.4.7.1.1.23
Node type: OBJECT-TYPE
Type: Integer32
Access: read-write
Description: This timer indicates the time that VISM should wait before outpulsing digits to the PBX after sending an off hook event. This applies only to immediate start protocol.
This object cannot be configured if the signaling type for the line to which this ds0 belongs is non cas. For a cas line this object CAN only be configured only after associating this ds0 with an endpoint.
This object will be applicable if ds0CasParameterSource has a value of mibValue (2).
The allowed range for this object is 10..1000.
What is ds0CasDelayImmedStart?
This Integer32 (0..65535), in milliseconds, is the time VISM waits after sending an off-hook event before outpulsing digits to the PBX, applicable only to the immediate-start signaling protocol. This delay gives the PBX time to prepare to receive digits before the gateway starts dialing, so setting it too short can cause the PBX to miss the first digits of an outpulsed number. For example, if a PBX consistently drops the first dialed digit under immediate-start signaling, an admin would increase ds0CasDelayImmedStart to give it more setup time.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.351.110.4.7.1.1.23 snmpwalk -v2c -c public <target> CISCO-VISM-DSX0-MIB::ds0CasDelayImmedStart
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.351.110.4.7.1.1.23.1 snmpget -v2c -c public <target> CISCO-VISM-DSX0-MIB::ds0CasDelayImmedStart.1
Set instance 1 (SNMPv2c):
snmpset -v2c -c private <target> 1.3.6.1.4.1.351.110.4.7.1.1.23.1 i <value>
Start monitoring Cisco VISM (Voice Interworking Service Module) card, MGX platform (legacy) with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the CISCO-VISM-DSX0-MIB::ds0CasDelayImmedStart OID value, configure state conditions and alerts, and monitor any Cisco VISM (Voice Interworking Service Module) card, MGX platform (legacy) from a single console.
OID Breakdown
Upper-level ancestors (10 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.351 | stratacom | CISCOWAN-SMI |
| 1.3.6.1.4.1.351.110 | basis | BASIS-MIB |
| 1.3.6.1.4.1.351.110.4 | basisLines | BASIS-MIB |
| 1.3.6.1.4.1.351.110.4.7 | dsx0Vism | BASIS-MIB |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.351.110.4.7.1 | dsx0VismCnfTable | CISCO-VISM-DSX0-MIB |
| 1.3.6.1.4.1.351.110.4.7.1.1 | dsx0VismCnfEntry | CISCO-VISM-DSX0-MIB |
| 1.3.6.1.4.1.351.110.4.7.1.1.23 | ds0CasDelayImmedStart | CISCO-VISM-DSX0-MIB |