All MIBs › REPEATER-REV4-MIB
Category: Legacy Hubs and Repeaters
Description: Defines revision 4 IEEE 802.3 repeater MIB objects for Ethernet hub monitoring and control.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is REPEATER-REV4-MIB?
REPEATER-REV4-MIB is a vendor-neutral IETF standards MIB (RFC 1516, revision 4 of the IEEE 802.3 repeater MIB) defining management objects for Ethernet repeater hubs — multiport devices that regenerate and broadcast Ethernet signals across all connected ports. It exposes repeater-level management objects (port count, which ports are enabled/on/operating) alongside per-port packet statistics such as packet counts, byte counts, collisions, and errors. Its monitoring purpose is entirely about hardware port health and traffic statistics on legacy shared-Ethernet hubs: tracking enabled versus on/operating port state to spot ports that should be active but aren't, and collision/error counts to detect a port with cabling or NIC problems. As a foundational 802.3-era standard, it predates and is largely superseded by switch-oriented MIBs (BRIDGE-MIB, IF-MIB) but remains relevant only where legacy repeater hardware is still in service. It is deployed on legacy Ethernet repeater/hub hardware, now mostly found in older industrial, lab, or legacy network installations rather than modern datacenters. Engineers can download the REPEATER-REV4-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in REPEATER-REV4-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- vendor-neutral, standards-based MIB (RFC 1516/IEEE 802.3), not tied to a specific manufacturer
- Ethernet repeater hubs (legacy shared-media hub hardware)
Monitoring Examples
An admin would poll rptrMgmtPortCount and rptrMgmtPortsEnable/rptrMgmtPortsOn/rptrMgmtPortsOper to confirm which repeater ports are configured, powered, and actually operating, then check rptrPktStatsColls and rptrPktStatsErrors per port — a port with a collision or error count climbing much faster than its peers typically points to a bad cable, duplex mismatch, or failing NIC on that segment. rptrMgmtResetCounters would be used to clear stats after remediating the fault to confirm the problem is resolved.
What Can Be Monitored
- port enabled/on/operational status
- port packet and byte counts
- port collision count
- port error count
This MIB depends on
Related MIBs
Imported Objects
From CTRON-MIB-NAMES
| repeaterRev4 | OBJECT-IDENTITY |
From RFC-1212
| OBJECT-TYPE |
From RFC1155-SMI
| Counter | |
| NetworkAddress |
From RFC1213-MIB
| DisplayString |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| repeaterrev4 | 1.3.6.1.4.1.52.4.1.1.1.4 | |||
| rptr | 1.3.6.1.4.1.52.4.1.1.1.4.1 | |||
| rptrMgmt | 1.3.6.1.4.1.52.4.1.1.1.4.1.1 | |||
| STR rptrMgmtName | 1.3.6.1.4.1.52.4.1.1.1.4.1.1.1 | DisplayString | read-write | The ASCII name assigned to this network. |
| INT rptrMgmtPortCount | 1.3.6.1.4.1.52.4.1.1.1.4.1.1.2 | INTEGER | read-only | Total number of ports residing on this lan segment. |
| INT rptrMgmtPortsEnable | 1.3.6.1.4.1.52.4.1.1.1.4.1.1.3 | INTEGER | read-write | Setting this object to Enable will cause all the ports residing in this network segment to be enabled. Setting this object to noEnable will have no effect. When read this object will always return noEnable. |
| INT rptrMgmtPortsOn | 1.3.6.1.4.1.52.4.1.1.1.4.1.1.4 | INTEGER | read-only | Get the total number of ON ports in this network. |
| INT rptrMgmtPortsOper | 1.3.6.1.4.1.52.4.1.1.1.4.1.1.5 | INTEGER | read-only | Get the number of operational ports in this network. |
| INT rptrMgmtBoardMap | 1.3.6.1.4.1.52.4.1.1.1.4.1.1.6 | INTEGER | read-only | Get a map of the chassis slots occupied by the boards in this network. |
| INT rptrMgmtInterfaceNum | 1.3.6.1.4.1.52.4.1.1.1.4.1.1.7 | INTEGER | read-only | Get the MIBII interface number of this network. A return of zero will mean this network is not associated with a MIBII interface. |
| INT rptrMgmtResetCounters | 1.3.6.1.4.1.52.4.1.1.1.4.1.1.8 | INTEGER | read-write | Setting this OID to 2 will reset the 'rptrPktStats', 'rptrProtocols' and 'rptrFrameSizes' RREV-4 branch static counters. Reading this OID will always return a 1. |
| rptrStats | 1.3.6.1.4.1.52.4.1.1.1.4.1.2 | |||
| rptrPktStats | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.1 | |||
| CTR rptrPktStatsPackets | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.1.1 | Counter | read-only | Get this repeater's total received packets. |
| CTR rptrPktStatsBytes | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.1.2 | Counter | read-only | Get this repeater's total received bytes. |
| CTR rptrPktStatsColls | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.1.3 | Counter | read-only | Get this repeater's total collisions. |
| CTR rptrPktStatsErrors | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.1.4 | Counter | read-only | Get this repeater's total errors. |
| CTR rptrPktStatsAlign | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.1.5 | Counter | read-only | Get this repeater's total frame alignment errors. |
| CTR rptrPktStatsCRC | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.1.6 | Counter | read-only | Get this repeater's total CRC errors. |
| CTR rptrPktStatsOOW | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.1.7 | Counter | read-only | Get this repeater's total out-of-window collisions. |
| CTR rptrPktStatsNoRsc | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.1.8 | Counter | read-only | This counter is the number of packets on this network that the hardware has processed that the management has either not seen yet, in the case of an active network, or has missed missed all together, in the case of a once active network. |
| CTR rptrPktStatsBroadcasts | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.1.9 | Counter | read-only | This counter is the number of broadcast packets on this network that the hardware has processed. |
| CTR rptrPktStatsMulticasts | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.1.10 | Counter | read-only | This counter is the number of multicast packets on this network that the hardware has processed. |
| rptrProtocols | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.2 | |||
| CTR rptrProtocolsOSI | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.2.1 | Counter | read-only | Get this repeater's total received OSI packets. |
| CTR rptrProtocolsNovell | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.2.2 | Counter | read-only | Get this repeater's total received Novell packets. |
| CTR rptrProtocolsBanyan | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.2.3 | Counter | read-only | Get this repeater's total received Banyan packets. |
| CTR rptrProtocolsDECNet | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.2.4 | Counter | read-only | Get this repeater's total received DECNet packets. |
| CTR rptrProtocolsXNS | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.2.5 | Counter | read-only | Get this repeater's total received XNS packets. |
| CTR rptrProtocolsIP | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.2.6 | Counter | read-only | Get this repeater's total received TCP/IP packets. |
| CTR rptrProtocolsCtron | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.2.7 | Counter | read-only | Get this repeater's total received CTRON Management packets. |
| CTR rptrProtocolsAppletalk | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.2.8 | Counter | read-only | Get this repeater's total received Appletalk packets. |
| CTR rptrProtocolsOther | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.2.9 | Counter | read-only | Get this repeater's total received unknown protocol packets. |
| rptrFrameSizes | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.3 | |||
| CTR rptrFrameSzRunt | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.3.1 | Counter | read-only | Get this repeater's total received packets of size less than 64 bytes. |
| CTR rptrFrameSz64To127 | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.3.2 | Counter | read-only | Get this repeater's total received packets of size between 64 and 127 bytes. |
| CTR rptrFrameSz128To255 | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.3.3 | Counter | read-only | Get this repeater's total received packets of size between 128 and 255 bytes. |
| CTR rptrFrameSz256To511 | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.3.4 | Counter | read-only | Get this repeater's total received packets of size between 256 and 511 bytes. |
| CTR rptrFrameSz512To1023 | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.3.5 | Counter | read-only | Get this repeater's total received packets of size between 512 and 1023 bytes. |
| CTR rptrFrameSz1024To1518 | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.3.6 | Counter | read-only | Get this repeater's total received packets of size between 1024 and 1518 bytes. |
| CTR rptrFrameSzGiant | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.3.7 | Counter | read-only | Get this repeater's total received packets of size greater than 1518 bytes. |
| rptrAlarms | 1.3.6.1.4.1.52.4.1.1.1.4.1.3 | |||
| INT rptrAlarmsTrafEnable | 1.3.6.1.4.1.52.4.1.1.1.4.1.3.1 | INTEGER | read-write | Get returns whether traffic alarms are enabled/disabled. Set allows for enabling/disabling of traffic alarms. |
| INT rptrAlarmsTrafThreshold | 1.3.6.1.4.1.52.4.1.1.1.4.1.3.2 | INTEGER | read-write | The maximum number of packets that will be allowed before an alarm is generated. |
| INT rptrAlarmsCollEnable | 1.3.6.1.4.1.52.4.1.1.1.4.1.3.3 | INTEGER | read-write | Get returns whether collision alarms are enabled/disabled. Set allows for enabling/disabling of collision alarms. |
| INT rptrAlarmsCollThreshold | 1.3.6.1.4.1.52.4.1.1.1.4.1.3.4 | INTEGER | read-write | The collision threshold is the maximum number of collisions within the time base that will be allowed before an alarm is generated. |
| INT rptrAlarmsErrEnable | 1.3.6.1.4.1.52.4.1.1.1.4.1.3.5 | INTEGER | read-write | Get returns whether error alarms are enabled/disabled. Set allows for enabling/disabling of error alarms. |
| INT rptrAlarmsErrThreshold | 1.3.6.1.4.1.52.4.1.1.1.4.1.3.6 | INTEGER | read-write | The percentage of errors per good packet within the timebase that will cause an alarm. The units of this value is in seconds. |
| INT rptrAlarmsErrSource | 1.3.6.1.4.1.52.4.1.1.1.4.1.3.7 | INTEGER | read-write | Get/Set a bit encoded map of which errors to include in the error sum, as follows: CRC_errors - Bit 0 - Least Significant Bit runts - Bit 1 OOW_colls - Bit 2 align_errs - Bit 3 undefined - Bit 4 Giants - Bit 5 |
| INT rptrAlarmsAlarmTimebase | 1.3.6.1.4.1.52.4.1.1.1.4.1.3.8 | INTEGER | read-write | The alarm timebase, in seconds. |
| INT rptrAlarmsBroadEnable | 1.3.6.1.4.1.52.4.1.1.1.4.1.3.9 | INTEGER | read-write | Get returns whether broadcast alarms are enabled/disabled. Set allows for enabling/disabling of broadcast alarms. |
| INT rptrAlarmsBroadThreshold | 1.3.6.1.4.1.52.4.1.1.1.4.1.3.10 | INTEGER | read-write | The broadcase threshold represents the maximum number of broadcasts that are allowed during the time base before an alarm is generated. |
| rptrRedundancy | 1.3.6.1.4.1.52.4.1.1.1.4.1.4 | |||
| rptrRedund | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.1 | |||
| INT rptrRedundReset | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.1.1 | INTEGER | read-write | If this object is set to Reset it will cause a reset of the redundancy object to occur. Setting this object to NoReset will do nothing. This object will always be read as NoReset. |
| INT rptrRedundPollInterval | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.1.2 | INTEGER | read-write | Get/Set the number of seconds between polls for redundancy. |
| STR rptrRedundTestTOD | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.1.3 | DisplayString | read-write | Get/Set the time of day at which the redundant circuits will be tested. The format of the time string is hh:mm:ss. |
| INT rptrRedundPerformTest | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.1.4 | INTEGER | read-write | If this object is set to Test it will cause a test of the redundant circuits to be performed. Setting this object to NoTest will have no effect. When read this object will always return NoTest. |
| INT rptrRedundMaxCrcts | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.1.5 | INTEGER | read-only | Returns the maximum number of circuits which may exist on this network. |
| rptrRedundCrctTable | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.2 | not-accessible | A list of redundant circuit objects for this repeater. | |
| rptrRedundCrctEntry | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.2.1 | not-accessible | A list of objects for a particular redundant circuit. | |
| INT rptrRedundCrctId | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.2.1.1 | INTEGER | read-only | Returns the index for a member circuit in the table of redundant circuits. |
| OCT rptrRedundCrctName | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.2.1.2 | OCTET STRING | read-write | Get/Set the name of the indicated circuit. |
| INT rptrRedundCrctRetrys | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.2.1.3 | INTEGER | read-write | Get/Set the the number of unanswered polls allowed for the circuit. |
| INT rptrRedundCrctNumBPs | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.2.1.4 | INTEGER | read-only | Get the number of board/port combinations associated with the circuit. |
| INT rptrRedundCrctNumAddr | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.2.1.5 | INTEGER | read-only | Get the number of IP Addresses associated with the circuit. |
| IP rptrRedundCrctAddAddr | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.2.1.6 | IpAddress | read-write | Add an IP Address to the polling list for the indicated circuit. |
| IP rptrRedundCrctDelAddr | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.2.1.7 | IpAddress | read-write | Delete an IP Address from the polling list of the indicated circuit. |
| INT rptrRedundCrctEnable | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.2.1.8 | INTEGER | read-write | If this object is set to Enable, the circuit is enabled. If this object is set to Disable, the circuit is disbabled. When read, this object returns the state of the object based on the last request made. |
| INT rptrRedundCrctReset | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.2.1.9 | INTEGER | read-write | If this object is set to Reset, the circuit is reset. All of the circuit's associated boards and ports are returned to NOT_USED, any associated IP Addresses are purged from the circuit's address list, the name is cleared, and the retry count is reset to a default value. Setting this object to NoReset has no effect. When read, NoReset is always returned. |
| rptrRedundPortTable | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.3 | not-accessible | A list of redundant port objects for this repeater. | |
| rptrRedundPortEntry | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.3.1 | not-accessible | A redundant port entry containing objects pertaining to a particular redundant port. | |
| INT rptrRedundPortId | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.3.1.1 | INTEGER | read-only | A unique value identifying an element in a sequence of member ports which belong to a circuit in the table of redundant circuits. This value is not a port number; rather it is a value which goes from 1 to the maximum number of ports which may be included in a redundant circuit. |
| INT rptrRedundPortCrctId | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.3.1.2 | INTEGER | read-only | A unique value identifying a member circuit in the table of redundant circuits. This value is similar to rptrRedundCrctId. |
| INT rptrRedundPortNum | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.3.1.3 | INTEGER | read-only | Returns the port number of a member port belonging to a redundant circuit. |
| INT rptrRedundPortBoardNum | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.3.1.4 | INTEGER | read-only | Returns the board number of a member port belonging to a redundant circuit. |
| INT rptrRedundPortType | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.3.1.5 | INTEGER | read-only | Return the state of a port associated with the indicated circuit. |
| rptrRedundAddrTable | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.4 | not-accessible | A list of redundant IP Address objects which belong to a circuit for this repeater. | |
| rptrRedundAddrEntry | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.4.1 | not-accessible | A entry containing objects pertaining to a particular redundant IP Address which belongs to a circuit. | |
| INT rptrRedundAddrId | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.4.1.1 | INTEGER | read-only | A unique value identifying an element in a sequence of member IP Addresses which belong to a circuit in the table of redundant circuits. This value goes from 1 to the maximum number of IP Addresses which may be included in a redundant circuit. |
| INT rptrRedundAddrCrctId | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.4.1.2 | INTEGER | read-only | A unique value identifying a member circuit in the table of redundant circuits. This value is similar to rptrRedundCrctId. |
| IP rptrRedundAddrIPAddr | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.4.1.3 | IpAddress | read-only | Returns an IP Address associated with the indicated circuit. |
| rptrSourceAddress | 1.3.6.1.4.1.52.4.1.1.1.4.1.5 | |||
| rptrSrcAddrListTable | 1.3.6.1.4.1.52.4.1.1.1.4.1.5.1 | not-accessible | This table defines the source address list that is defined at the repeater level. | |
| rptrSrcAddrListEntry | 1.3.6.1.4.1.52.4.1.1.1.4.1.5.1.1 | not-accessible | Defines a specific source address object. | |
| INT rptrSrcAddrListId | 1.3.6.1.4.1.52.4.1.1.1.4.1.5.1.1.1 | INTEGER | read-only | Returns an index into a table of source address seen by this repeater. |
| OCT rptrSrcAddrAddressList | 1.3.6.1.4.1.52.4.1.1.1.4.1.5.1.1.2 | OCTET STRING | read-only | Returns a source address seen by this repeater. |
| rptrSrcAddrSrcTable | 1.3.6.1.4.1.52.4.1.1.1.4.1.5.2 | not-accessible | This table defines the list of all source addresses that have been seen. | |
| rptrSrcAddrSrcTableEntry | 1.3.6.1.4.1.52.4.1.1.1.4.1.5.2.1 | not-accessible | Describes a particular source address source entry. | |
| OCT rptrSrcAddrSrcTableEntryId | 1.3.6.1.4.1.52.4.1.1.1.4.1.5.2.1.1 | OCTET STRING | read-only | Returns the source address to which this table's information pertains. |
| INT rptrSrcAddrSrcTableEntryPort | 1.3.6.1.4.1.52.4.1.1.1.4.1.5.2.1.2 | INTEGER | read-only | Returns the port# of the port that sourced the source address. |
| INT rptrSrcAddrSrcTableEntryPortGroup | 1.3.6.1.4.1.52.4.1.1.1.4.1.5.2.1.3 | INTEGER | read-only | Returns the port group# of the port that sourced the source address. |
| rptrSrcAddrMgmt | 1.3.6.1.4.1.52.4.1.1.1.4.1.5.3 | |||
| INT rptrSrcAddrMgmtSrcAgeInterval | 1.3.6.1.4.1.52.4.1.1.1.4.1.5.3.1 | INTEGER | read-write | Get/Set source addressing ageing interval. |
| INT rptrSrcAddrMgmtPortLock | 1.3.6.1.4.1.52.4.1.1.1.4.1.5.3.2 | INTEGER | read-write | Setting this object to Lock will activate the network port security lock. Setting a value of portMisMatch(3) is invalid. A value of portMisMatch(3) reflects that not all ports are at the same value. |
| INT rptrSrcAddrMgmtActiveUsers | 1.3.6.1.4.1.52.4.1.1.1.4.1.5.3.3 | INTEGER | read-only | Get the number of active users on this network. |
| INT rptrSrcAddrMgmtHashType | 1.3.6.1.4.1.52.4.1.1.1.4.1.5.3.4 | INTEGER | read-write | Defines the type of hashing that will be used for source address management. In a DEC-NET environment or a combination fo DEC-NET and non DEC-NET users where source address hash access is a concern a value of decHash(2) may yield better results. For non DEC-NET users a value of noDecHash(1) is preferred. |
| rptrTrap | 1.3.6.1.4.1.52.4.1.1.1.4.1.6 | |||
| rptrHwTrapSet | 1.3.6.1.4.1.52.4.1.1.1.4.1.6.1 | |||
| INT rptrHwTrapSetLink | 1.3.6.1.4.1.52.4.1.1.1.4.1.6.1.1 | INTEGER | read-write | Enables and disables link traps for this network. Setting a value of disable(1) is equivalent to setting all instances of rptrPortHwTrapSetLink to a value of disable(1). Setting a value of enable(2) is equivalent to setting all instances of rptrPortHwTrapSetLink to a value of disable(2). Setting a value of other(3) is not allowed. This object will read with the value of disable(1) if all instances of rptrPortHwTrapSetLink for this network are currently set to a value of disable(1). This object will read with the value of enable(2) if all instances of rptrPortHwTrapSetLink for this network are currently set to a value of enable(2). This object will read with the value of other(3) if all instances of rptrPortHwTrapSetLink for this network are not currently set to a value the same value. |
| INT rptrHwTrapSetSeg | 1.3.6.1.4.1.52.4.1.1.1.4.1.6.1.2 | INTEGER | read-write | Enables and disables segmentation traps for this network. Setting a value of disable(1) is equivalent to setting all instances of rptrPortHwTrapSetSeg to a value of disable(1). Setting a value of enable(2) is equivalent to setting all instances of rptrPortHwTrapSetSeg to a value of disable(2). Setting a value of other(3) is not allowed. This object will read with the value of disable(1) if all instances of rptrPortHwTrapSetSeg for this network are currently set to a value of disable(1). This object will read with the value of enable(2) if all instances of rptrPortHwTrapSetSeg for this network are currently set to a value of enable(2). This object will read with the value of other(3) if all instances of rptrPortHwTrapSetSeg for this network are not currently set to a value the same value. |
| rptrSaTrapSet | 1.3.6.1.4.1.52.4.1.1.1.4.1.6.2 | |||
| INT rptrSaTrapSetSrcaddr | 1.3.6.1.4.1.52.4.1.1.1.4.1.6.2.1 | INTEGER | read-write | Enables and disables source address traps for this network. Setting a value of disable(1) is equivalent to setting all instances of rptrPortSaTrapSetSrcaddr to a value of disable(1). Setting a value of enable(2) is equivalent to setting all instances of rptrPortSaTrapSetSrcaddr to a value of disable(2). Setting a value of other(3) is not allowed. This object will read with the value of disable(1) if all instances of rptrPortSaTrapSetSrcaddr for this network are currently set to a value of disable(1). This object will read with the value of enable(2) if all instances of rptrPortSaTrapSetSrcaddr for this network are currently set to a value of enable(2). This object will read with the value of other(3) if all instances of rptrPortSaTrapSetSrcaddr for this network are not currently set to a value the same value. |
| rptrSaSecurity | 1.3.6.1.4.1.52.4.1.1.1.4.1.7 | |||
| INT rptrSecurityLockState | 1.3.6.1.4.1.52.4.1.1.1.4.1.7.1 | INTEGER | read-write | Setting this object to Lock will activate the network port security lock. Setting a value of portMisMatch(3) is invalid. A value of portMisMatch(3) reflects that not all ports are at the same value. |
| INT rptrSecuritySecureState | 1.3.6.1.4.1.52.4.1.1.1.4.1.7.2 | INTEGER | read-only | The status of source address security of the network. Ports on the network that are secure(1), can be locked in order to enable security. nonSecure(2) ports cannot be locked. Setting a value of portMisMatch(3) is invalid. A value of portMisMatch(3) reflects that not all ports are at the same value. |
| INT rptrSecurityLearnState | 1.3.6.1.4.1.52.4.1.1.1.4.1.7.3 | INTEGER | read-write | The learn state of the network. This object will only be applied to ports that are unlocked. If set to learn(1), all addresses are deleted on the ports and learning begins once again. If it is set to noLearn(2), learning stops on the port. Setting a value of portMisMatch(3) is invalid. A value of portMisMatch(3) reflects that not all ports are at the same value. |
| INT rptrSecurityLearnMode | 1.3.6.1.4.1.52.4.1.1.1.4.1.7.4 | INTEGER | read-write | Get/Set the learn mode of the network. If set to onetime learn mode oneTime(1), each port is capable of learning two addresses and securing on both destination and source addresses once they are locked. If set to continuous learn continuous(2), all addresses are initially deleted and each port continuously replaces the existing secure source address with the latest source address it sees. Setting a value of portMisMatch(3) is invalid. A value of portMisMatch(3) reflects that not all ports are at the same value. |
| rptrPortGroup | 1.3.6.1.4.1.52.4.1.1.1.4.2 | |||
| rptrPortGrpMgmtTable | 1.3.6.1.4.1.52.4.1.1.1.4.2.1 | not-accessible | A list of port management objects for this repeater node. | |
| rptrPortGrpMgmtEntry | 1.3.6.1.4.1.52.4.1.1.1.4.2.1.1 | not-accessible | An entry containing objects pertaining to port management for a port group. | |
| INT rptrPortGrpMgmtGrpId | 1.3.6.1.4.1.52.4.1.1.1.4.2.1.1.1 | INTEGER | read-only | Returns an index to a port group for which the information in this table pertains. |
| STR rptrPortGrpMgmtName | 1.3.6.1.4.1.52.4.1.1.1.4.2.1.1.2 | DisplayString | read-write | Gets/Sets a name for the specified port group. |
| INT rptrPortGrpMgmtPortCount | 1.3.6.1.4.1.52.4.1.1.1.4.2.1.1.3 | INTEGER | read-only | Get total number of ports contained on the board. Notice that this is the physical port count. |
| INT rptrPortGrpMgmtPortsEnable | 1.3.6.1.4.1.52.4.1.1.1.4.2.1.1.4 | INTEGER | read-write | Setting this object to Enable will cause all the ports residing in this network segment to be enabled. Setting this object to noEnable will have no effect. When read this object will always return noEnable. |
| INT rptrPortGrpMgmtPortsOn | 1.3.6.1.4.1.52.4.1.1.1.4.2.1.1.5 | INTEGER | read-only | Get total number of ON ports in this port group. |
| INT rptrPortGrpMgmtPortsOper | 1.3.6.1.4.1.52.4.1.1.1.4.2.1.1.6 | INTEGER | read-only | Get total number of operational ports in the port group. |
| INT rptrPortGrpMgmtLogPortCount | 1.3.6.1.4.1.52.4.1.1.1.4.2.1.1.7 | INTEGER | read-only | Get total number of ports contained in this port group. |
| rptrPortGrpStats | 1.3.6.1.4.1.52.4.1.1.1.4.2.2 | |||
| rptrPortGrpPktStatsTbl | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.1 | not-accessible | This table provides packet statistics for port group. | |
| rptrPortGrpPktStatsEntry | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.1.1 | not-accessible | Defines a specific packet statistics entry. | |
| INT rptrPortGrpPktStatsId | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.1.1.1 | INTEGER | read-only | Returns an index to a port group for which the information in this table pertains. |
| CTR rptrPortGrpPktStatsPkts | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.1.1.2 | Counter | read-only | Return this port group's total received packets. |
| CTR rptrPortGrpPktStatsBytes | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.1.1.3 | Counter | read-only | Return this port group's total received bytes. |
| CTR rptrPortGrpPktStatsColls | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.1.1.4 | Counter | read-only | Return this port group's total collisions. |
| CTR rptrPortGrpPktStatsErrors | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.1.1.5 | Counter | read-only | Return this port group's total errors. |
| CTR rptrPortGrpPktStatsAlign | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.1.1.6 | Counter | read-only | Return this port group's total frame alignment errors. |
| CTR rptrPortGrpPktStatsCRC | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.1.1.7 | Counter | read-only | Return this port group's total CRC errors. |
| CTR rptrPortGrpPktStatsOOW | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.1.1.8 | Counter | read-only | Return this port group's total out-of-window collisions. |
| CTR rptrPortGrpPktStatsBroadcasts | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.1.1.9 | Counter | read-only | Return this port group's total received broadcast packets. |
| CTR rptrPortGrpPktStatsMulticasts | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.1.1.10 | Counter | read-only | Return this port group's total received multicast packets. |
| rptrPortGrpProtocolTbl | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.2 | not-accessible | Provides port group protocol statistics. | |
| rptrPortGrpProtocolEntry | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.2.1 | not-accessible | Defines a specific port group protocol statistics entry. | |
| INT rptrPortGrpProtocolId | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.2.1.1 | INTEGER | read-only | Returns an index to a port group for which the information in this table pertains. |
| CTR rptrPortGrpProtocolOSI | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.2.1.2 | Counter | read-only | Return this port group's total received OSI packets. |
| CTR rptrPortGrpProtocolNovell | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.2.1.3 | Counter | read-only | Return this port group's total received Novell packets. |
| CTR rptrPortGrpProtocolBanyan | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.2.1.4 | Counter | read-only | Return this port group's total received Banyan packets. |
| CTR rptrPortGrpProtocolDECNet | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.2.1.5 | Counter | read-only | Return this port group's total received DECNet packets. |
| CTR rptrPortGrpProtocolXNS | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.2.1.6 | Counter | read-only | Return this port group's total received XNS packets. |
| CTR rptrPortGrpProtocolIP | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.2.1.7 | Counter | read-only | Return this port group's total received TCP/IP packets. |
| CTR rptrPortGrpProtocolCtron | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.2.1.8 | Counter | read-only | Return this port group's total received CTRON Management packets. |
| CTR rptrPortGrpProtocolAppletalk | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.2.1.9 | Counter | read-only | Return this port group's total received Appletalk packets. |
| CTR rptrPortGrpProtocolOther | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.2.1.10 | Counter | read-only | Return this port group's total received unknown protocol packets. |
| rptrPortGrpFrameSzTbl | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.3 | not-accessible | Defines frame sizes as seen by this port group. | |
| rptrPortGrpFrameSzEntry | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.3.1 | not-accessible | Defines a particular frame size entry. | |
| INT rptrPortGrpFrameSzId | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.3.1.1 | INTEGER | read-only | Returns an index to a port group for which the information in this table pertains. |
| CTR rptrPortGrpFrameSzRunt | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.3.1.2 | Counter | read-only | Return this port group's total received packets of size less than 64 bytes. |
| CTR rptrPortGrpFrameSz64To127 | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.3.1.3 | Counter | read-only | Return this port group's total received packets of size between 64 and 127 bytes. |
| CTR rptrPortGrpFrameSz128To255 | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.3.1.4 | Counter | read-only | Return this port group's total received packets of size between 128 and 255 bytes. |
| CTR rptrPortGrpFrameSz256To511 | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.3.1.5 | Counter | read-only | Return this port group's total received packets of size between 256 and 511 bytes. |
| CTR rptrPortGrpFrameSz512To1023 | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.3.1.6 | Counter | read-only | Return this port group's total received packets of size between 512 and 1023 bytes. |
| CTR rptrPortGrpFrameSz1024To1518 | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.3.1.7 | Counter | read-only | Return this port group's total received packets of size between 1024 and 1518 bytes. |
| CTR rptrPortGrpFrameSzGiant | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.3.1.8 | Counter | read-only | Return this port group's total received packets of size greater than 1518 bytes. |
| rptrPortGrpAlarmTable | 1.3.6.1.4.1.52.4.1.1.1.4.2.3 | not-accessible | A list of port group alarm objects for this repeater node. | |
| rptrPortGrpAlarmEntry | 1.3.6.1.4.1.52.4.1.1.1.4.2.3.1 | not-accessible | An entry containing objects pertaining to port group alarms for a port group. | |
| INT rptrPortGrpAlarmId | 1.3.6.1.4.1.52.4.1.1.1.4.2.3.1.1 | INTEGER | read-only | Returns an index to a port group for which the information in this table pertains. |
| INT rptrPortGrpAlarmTrafEnable | 1.3.6.1.4.1.52.4.1.1.1.4.2.3.1.2 | INTEGER | read-write | Get returns whether traffic alarms are enabled/disabled. Set allows for enabling/disabling of traffic alarms. |
| INT rptrPortGrpAlarmTrafThreshold | 1.3.6.1.4.1.52.4.1.1.1.4.2.3.1.3 | INTEGER | read-write | The maximum number of packets that will be allowed before an alarm is generated. |
| INT rptrPortGrpAlarmTrafGrpDisable | 1.3.6.1.4.1.52.4.1.1.1.4.2.3.1.4 | INTEGER | read-write | Set will permit a port group to be disabled on a traffic alarm condition. Get will show whether the port group disabling is allowed or not. |
| INT rptrPortGrpAlarmCollEnable | 1.3.6.1.4.1.52.4.1.1.1.4.2.3.1.5 | INTEGER | read-write | Get returns whether collision alarms are enabled/disabled. Set allows for enabling/disabling of collision alarms. |
| INT rptrPortGrpAlarmCollThreshold | 1.3.6.1.4.1.52.4.1.1.1.4.2.3.1.6 | INTEGER | read-write | The collision threshold is the maximum number of collisions within the time base that will be allowed before an alaram is generated. |
| INT rptrPortGrpAlarmCollBdDisable | 1.3.6.1.4.1.52.4.1.1.1.4.2.3.1.7 | INTEGER | read-write | Set will permit a port group to be disabled on a collision alarm condition. Get will show whether the port group disabling is allowed or not. |
| INT rptrPortGrpAlarmErrEnable | 1.3.6.1.4.1.52.4.1.1.1.4.2.3.1.8 | INTEGER | read-write | Get returns whether error alarms are enabled/disabled. Set allows for enabling/disabling of error alarms. |
| INT rptrPortGrpAlarmErrThreshold | 1.3.6.1.4.1.52.4.1.1.1.4.2.3.1.9 | INTEGER | read-write | Get/Set the percentage of errors per good packet within the timebase that will cause an alarm. |
| INT rptrPortGrpAlarmErrSource | 1.3.6.1.4.1.52.4.1.1.1.4.2.3.1.10 | INTEGER | read-write | Get/Set a bit encoded map of which errors to include in the error sum, as follows: CRC_errors - Bit 0 - Least Significant Bit runts - Bit 1 OOW_colls - Bit 2 align_errs - Bit 3 undefined - Bit 4 Giants - Bit 5 |
| INT rptrPortGrpAlarmErrGrpDisable | 1.3.6.1.4.1.52.4.1.1.1.4.2.3.1.11 | INTEGER | read-write | Set will permit a port group to be disabled on an error alarm condition. Get will show whether the port group disabling is allowed or not. |
| INT rptrPortGrpAlarmBroadEnable | 1.3.6.1.4.1.52.4.1.1.1.4.2.3.1.12 | INTEGER | read-write | Get returns whether broadcast alarms are enabled/disabled. Set allows for enabling/disabling of broadcast alarms. |
| INT rptrPortGrpAlarmBroadThreshold | 1.3.6.1.4.1.52.4.1.1.1.4.2.3.1.13 | INTEGER | read-write | The broadcase threshold represents the maximum number of broadcasts that are allowed during the time base before an alarm is generated. |
| INT rptrPortGrpAlarmBroadGrpDisable | 1.3.6.1.4.1.52.4.1.1.1.4.2.3.1.14 | INTEGER | read-write | Set will permit a port group to be disabled on a broadcast alarm condition. Get will show whether the port group disabling is allowed or not. |
| rptrPortGrpSrcAddrTable | 1.3.6.1.4.1.52.4.1.1.1.4.2.4 | not-accessible | This table provides a list of the number of active users that have been seen by port group. | |
| rptrPortGrpSrcAddrEntry | 1.3.6.1.4.1.52.4.1.1.1.4.2.4.1 | not-accessible | Defines a specific active user entry. | |
| INT rptrPortGrpSrcAddrId | 1.3.6.1.4.1.52.4.1.1.1.4.2.4.1.1 | INTEGER | read-only | Returns an index to a port group for which the information in this table pertains. |
| INT rptrPortGrpSrcAddrActiveUsers | 1.3.6.1.4.1.52.4.1.1.1.4.2.4.1.2 | INTEGER | read-only | Returns the total number of active users seen by this port group. |
| rptrPortGrpTrap | 1.3.6.1.4.1.52.4.1.1.1.4.2.5 | |||
| rptrPortGrpHwTrapSet | 1.3.6.1.4.1.52.4.1.1.1.4.2.5.1 | |||
| rptrPortGrpHwTrapTable | 1.3.6.1.4.1.52.4.1.1.1.4.2.5.1.1 | not-accessible | A list of trap enable/disable at the port group level. Disable here is equivalent to disable for each port in the port group. | |
| rptrPortGrpHwTrapEntry | 1.3.6.1.4.1.52.4.1.1.1.4.2.5.1.1.1 | not-accessible | Individual trap entries for port group enable/disable. | |
| INT rptrPortGrpHwTrapSetGrpId | 1.3.6.1.4.1.52.4.1.1.1.4.2.5.1.1.1.1 | INTEGER | read-only | Returns an index to a port group for which the information in this table pertains. |
| INT rptrPortGrpHwTrapSetLink | 1.3.6.1.4.1.52.4.1.1.1.4.2.5.1.1.1.2 | INTEGER | read-write | Enables and disables link traps for the specified port group. Setting a value of disable(1) is equivalent to setting all instances of rptrPortHwTrapSetLink to a value of disable(1). Setting a value of enable(2) is equivalent to setting all instances of rptrPortHwTrapSetLink to a value of disable(2). Setting a value of other(3) is not allowed. This object will read with the value of disable(1) if all instances of rptrPortHwTrapSetLink for this port group are currently set to a value of disable(1). This object will read with the value of enable(2) if all instances of rptrPortHwTrapSetLink for this port group are currently set to a value of enable(2). This object will read with the value of other(3) if all instances of rptrPortHwTrapSetLink for this port group are not currently set to a value the same value. |
| INT rptrPortGrpHwTrapSetSeg | 1.3.6.1.4.1.52.4.1.1.1.4.2.5.1.1.1.3 | INTEGER | read-write | Enables and disables segmentation traps for the specified port group. Setting a value of disable(1) is equivalent to setting all instances of rptrPortHwTrapSetSeg to a value of disable(1). Setting a value of enable(2) is equivalent to setting all instances of rptrPortHwTrapSetSeg to a value of disable(2). Setting a value of other(3) is not allowed. This object will read with the value of disable(1) if all instances of rptrPortHwTrapSetSeg for this port group are currently set to a value of disable(1). This object will read with the value of enable(2) if all instances of rptrPortHwTrapSetSeg for this port group are currently set to a value of enable(2). This object will read with the value of other(3) if all instances of rptrPortHwTrapSetSeg for this port group are not currently set to a value the same value. |
| rptrPortGrpSaTrapSet | 1.3.6.1.4.1.52.4.1.1.1.4.2.5.2 | |||
| rptrPortGrpSaTrapTable | 1.3.6.1.4.1.52.4.1.1.1.4.2.5.2.1 | not-accessible | A list of trap enable/disable at the port group level. Disable here is equivalent to disable for each port in the port group. | |
| rptrPortGrpSaTrapEntry | 1.3.6.1.4.1.52.4.1.1.1.4.2.5.2.1.1 | not-accessible | Individual trap entries for port group enable/disable. | |
| INT rptrPortGrpSaTrapSetGrpId | 1.3.6.1.4.1.52.4.1.1.1.4.2.5.2.1.1.1 | INTEGER | read-only | Returns an index to a port group for which the information in this table pertains. |
| INT rptrPortGrpSaTrapSetSrcaddr | 1.3.6.1.4.1.52.4.1.1.1.4.2.5.2.1.1.2 | INTEGER | read-write | Enables and disables source address traps for the specified port group. Setting a value of disable(1) is equivalent to setting all instances of rtprPortSaTrapSetSrcaddr to a value of disable(1). Setting a value of enable(2) is equivalent to setting all instances of rtprPortSaTrapSetSrcaddr to a value of disable(2). Setting a value of other(3) is not allowed. This object will read with the value of disable(1) if all instances of rptrPortSaTrapSetSrcaddr for this port group are currently set to a value of disable(1). This object will read with the value of enable(2) if all instances of rptrPortSaTrapSetSrcaddr for this port group are currently set to a value of enable(2). This object will read with the value of other(3) if all instances of rptrPortSaTrapSetSrcaddr for this port group are not currently set to a value the same value. |
| rptrPortGrpSrcAddrLockTable | 1.3.6.1.4.1.52.4.1.1.1.4.2.6 | not-accessible | This table defines the status of the port group source address security locks. | |
| rptrPortGrpSrcAddrLockEntry | 1.3.6.1.4.1.52.4.1.1.1.4.2.6.1 | not-accessible | DeDefines a status of a particular port group security lock. | |
| INT rptrPortGrpSrcAddrLockGrpId | 1.3.6.1.4.1.52.4.1.1.1.4.2.6.1.1 | INTEGER | read-only | Defines a particular port group for which this source address security lock information pertains. |
| INT rptrPortGrpSrcAddrLock | 1.3.6.1.4.1.52.4.1.1.1.4.2.6.1.2 | INTEGER | read-write | Allows setting of the security lock status for this port group. unlock(1) - Unlocks the source address lock this group, lock(2) - Locks the source address for this group, Setting a value of portMisMatch(3) is invalid. A value of portMisMatch(3) reflects that not all ports are at the same value. |
| INT rptrPortGrpSASecuritySecureState | 1.3.6.1.4.1.52.4.1.1.1.4.2.6.1.3 | INTEGER | read-only | The state of the source addressing security for this port group. Ports on the port group that are secure(1), can be locked in order to enable security. When a value of nonSecure(2) is returned ports cannot be locked. Setting a value of portMisMatch(3) is invalid. A value of portMisMatch(3) reflects that not all ports are at the same value. |
| INT rptrPortGrpSASecurityLearnState | 1.3.6.1.4.1.52.4.1.1.1.4.2.6.1.4 | INTEGER | read-write | The learn state of source addressing security for this port group. This object will only be applied to ports that are unlocked. If set to learn(1), all addresses are deleted on the port and learning begins once again. If it is set to noLearn(2), learning stops on the port. Setting a value of portMisMatch(3) is invalid. A value of portMisMatch(3) reflects that not all ports are at the same value. |
| INT rptrPortGrpSASecurityLearnMode | 1.3.6.1.4.1.52.4.1.1.1.4.2.6.1.5 | INTEGER | read-write | The learn mode of source addressing security port group. If set to oneTime(1), each port is capable of learning two addresses and securing on both destination and source addresses once they are locked. If set to continuous(2), all addresses are initially deleted and each port continuously replaces the existing secure source address with latest source address it sees. Setting a value of portMisMatch(3) is invalid. A value of portMisMatch(3) reflects that not all ports are at the same value. |
| rptrPort | 1.3.6.1.4.1.52.4.1.1.1.4.3 | |||
| rptrPortMgmtTable | 1.3.6.1.4.1.52.4.1.1.1.4.3.1 | not-accessible | A list of port management objects for this repeater node. | |
| rptrPortMgmtEntry | 1.3.6.1.4.1.52.4.1.1.1.4.3.1.1 | not-accessible | An entry containing objects pertaining to port management for a port. | |
| INT rptrPortMgmtPortId | 1.3.6.1.4.1.52.4.1.1.1.4.3.1.1.1 | INTEGER | read-only | Returns an index to a port for which the information in this table pertains. |
| INT rptrPortMgmtPortGrpId | 1.3.6.1.4.1.52.4.1.1.1.4.3.1.1.2 | INTEGER | read-only | Returns an index to a port group for which the information in this table pertains. |
| STR rptrPortMgmtName | 1.3.6.1.4.1.52.4.1.1.1.4.3.1.1.3 | DisplayString | read-write | Sets/Gets an ASCII name assigned to this port. |
| INT rptrPortMgmtAdminState | 1.3.6.1.4.1.52.4.1.1.1.4.3.1.1.4 | INTEGER | read-write | Setting this object to Enable will cause port to be enabled. Setting this object to Disable will cause the port to be disabled. When read this object will return the state of the object per the last request. |
| INT rptrPortMgmtOperState | 1.3.6.1.4.1.52.4.1.1.1.4.3.1.1.5 | INTEGER | read-only | Get port operational status. |
| OID rptrPortMgmtPortType | 1.3.6.1.4.1.52.4.1.1.1.4.3.1.1.6 | OBJECT IDENTIFIER | read-only | Uniquely defines the repeater port type. A authoritative identification for a port type. By convention, this value is allocated within the SMI enterprises subtree (1.3.6.1.4.1), and provides an easy and unambiguous means to determine the type of repeater port. |
| rptrPortStats | 1.3.6.1.4.1.52.4.1.1.1.4.3.2 | |||
| rptrPortPktStatsTbl | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.1 | not-accessible | Provides repeater port packet statistics. | |
| rptrPortPktStatsEntry | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.1.1 | not-accessible | Provides basic statistics for a specific port. | |
| INT rptrPortPktStatsPortId | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.1.1.1 | INTEGER | read-only | Returns an index to a port for which the information in this table pertains. |
| INT rptrPortPktStatsPortGrpId | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.1.1.2 | INTEGER | read-only | Returns an index to a port group for which the information in this table pertains. |
| CTR rptrPortPktStatsPackets | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.1.1.3 | Counter | read-only | Get this port's total received packets. |
| CTR rptrPortPktStatsBytes | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.1.1.4 | Counter | read-only | Get this port's total received bytes. |
| CTR rptrPortPktStatsColls | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.1.1.5 | Counter | read-only | Get this port's total collisions. |
| CTR rptrPortPktStatsErrors | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.1.1.6 | Counter | read-only | Get this port's total errors. |
| CTR rptrPortPktStatsAlign | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.1.1.7 | Counter | read-only | Get this port's total frame alignment errors. |
| CTR rptrPortPktStatsCRC | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.1.1.8 | Counter | read-only | Get this port's total CRC errors. |
| CTR rptrPortPktStatsOOW | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.1.1.9 | Counter | read-only | Get this port's total out-of-window collisions. |
| CTR rptrPortPktStatsBroadcasts | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.1.1.10 | Counter | read-only | Get this port's total received broadcast packets. |
| CTR rptrPortPktStatsMulticasts | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.1.1.11 | Counter | read-only | Get this port's total received multicast packets. |
| rptrPortProtocolTbl | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.2 | not-accessible | Provides statistics about the protocols seen by the different ports. | |
| rptrPortProtocolEntry | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.2.1 | not-accessible | An entry containing objects pertaining to statistics about protocols seen by different ports. | |
| INT rptrPortProtocolPortId | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.2.1.1 | INTEGER | read-only | Returns an index to a port for which the information in this table pertains. |
| INT rptrPortProtocolPortGrpId | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.2.1.2 | INTEGER | read-only | Returns an index to a port group for which the information in this table pertains. |
| CTR rptrPortProtocolOSI | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.2.1.3 | Counter | read-only | Get this port's total received OSI protocol packets. |
| CTR rptrPortProtocolNovell | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.2.1.4 | Counter | read-only | Get this port's total received Novell protocol packets. |
| CTR rptrPortProtocolBanyan | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.2.1.5 | Counter | read-only | Get this port's total received Banyan protocol packets. |
| CTR rptrPortProtocolDECNet | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.2.1.6 | Counter | read-only | Get this port's total received DECNet protocol packets. |
| CTR rptrPortProtocolXNS | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.2.1.7 | Counter | read-only | Get this port's total received XNS protocol packets. |
| CTR rptrPortProtocolIP | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.2.1.8 | Counter | read-only | Get this port's total received TCP/IP protocol packets. |
| CTR rptrPortProtocolCtron | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.2.1.9 | Counter | read-only | Get this port's total received CTRON Management protocol packets. |
| CTR rptrPortProtocolAppletalk | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.2.1.10 | Counter | read-only | Get this port's total received Appletalk protocol packets. |
| CTR rptrPortProtocolOther | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.2.1.11 | Counter | read-only | Get this port's total received unknown protocol packets. |
| rptrPortFrameSzTbl | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.3 | not-accessible | Provides repeater port frame size statistics. | |
| rptrPortFrameSzEntry | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.3.1 | not-accessible | Describes a set of frame size statistics for a specific port. | |
| INT rptrPortFrameSzPortId | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.3.1.1 | INTEGER | read-only | Returns an index to a port for which the information in this table pertains. |
| INT rptrPortFrameSzPortGrpId | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.3.1.2 | INTEGER | read-only | Returns an index to a port group for which the information in this table pertains. |
| CTR rptrPortFrameSzRunt | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.3.1.3 | Counter | read-only | Get this port's total received packets of size less than 64 bytes. |
| CTR rptrPortFrameSz64To127 | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.3.1.4 | Counter | read-only | Get this port's total received packets of size between 64 and 127 bytes. |
| CTR rptrPortFrameSz128To255 | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.3.1.5 | Counter | read-only | Get this port's total received packets of size between 128 and 255 bytes. |
| CTR rptrPortFrameSz256To511 | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.3.1.6 | Counter | read-only | Get this port's total received packets of size between 256 and 511 bytes. |
| CTR rptrPortFrameSz512To1023 | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.3.1.7 | Counter | read-only | Get this port's total received packets of size between 512 and 1023 bytes. |
| CTR rptrPortFrameSz1024To1518 | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.3.1.8 | Counter | read-only | Get this port's total received packets of size between 1024 and 1518 bytes. |
| CTR rptrPortFrameSzGiant | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.3.1.9 | Counter | read-only | Get this port's total received packets of size greater than 1518 bytes. |
| rptrPortAlarmTable | 1.3.6.1.4.1.52.4.1.1.1.4.3.3 | not-accessible | A list of port alarm objects for this repeater node. | |
| rptrPortAlarmEntry | 1.3.6.1.4.1.52.4.1.1.1.4.3.3.1 | not-accessible | An entry containing objects pertaining to port alarm objects for a port group. | |
| INT rptrPortAlarmPortId | 1.3.6.1.4.1.52.4.1.1.1.4.3.3.1.1 | INTEGER | read-only | Returns an index to a port for which the information in this table pertains. |
| INT rptrPortAlarmPortGrpId | 1.3.6.1.4.1.52.4.1.1.1.4.3.3.1.2 | INTEGER | read-only | Returns an index to a port group for which the information in this table pertains. |
| INT rptrPortAlarmTrafEnable | 1.3.6.1.4.1.52.4.1.1.1.4.3.3.1.3 | INTEGER | read-write | Get returns whether traffic alarms are enabled/disabled. Set allows for enabling/disabling of traffic alarms. |
| INT rptrPortAlarmTrafThreshold | 1.3.6.1.4.1.52.4.1.1.1.4.3.3.1.4 | INTEGER | read-write | The maximum number of packets that will be allowed before an alarm is generated. |
| INT rptrPortAlarmTrafPortDisable | 1.3.6.1.4.1.52.4.1.1.1.4.3.3.1.5 | INTEGER | read-write | Set will permit a port to be disabled on a traffic alarm condition. Get will show whether the port disabling is allowed or not. |
| INT rptrPortAlarmCollEnable | 1.3.6.1.4.1.52.4.1.1.1.4.3.3.1.6 | INTEGER | read-write | Get returns whether collision alarms are enabled/disabled. Set allows for enabling/disabling of collision alarms. |
| INT rptrPortAlarmCollThreshold | 1.3.6.1.4.1.52.4.1.1.1.4.3.3.1.7 | INTEGER | read-write | The collision threshold is the maximum number of collisions within the time base that will be allowed before an alaram is generated. |
| INT rptrPortAlarmCollPortDisable | 1.3.6.1.4.1.52.4.1.1.1.4.3.3.1.8 | INTEGER | read-write | Set will permit a port to be disabled on a collision alarm condition. Get will show whether the port disabling is allowed or not. |
| INT rptrPortAlarmErrEnable | 1.3.6.1.4.1.52.4.1.1.1.4.3.3.1.9 | INTEGER | read-write | Get returns whether error alarms are enabled/disabled. Set allows for enabling/disabling of error alarms. |
| INT rptrPortAlarmErrThreshold | 1.3.6.1.4.1.52.4.1.1.1.4.3.3.1.10 | INTEGER | read-write | Get/Set the percentage of errors per good packet within the timebase that will cause an alarm. |
| INT rptrPortAlarmErrSource | 1.3.6.1.4.1.52.4.1.1.1.4.3.3.1.11 | INTEGER | read-write | Get/Set a bit encoded map of which errors to include in the error sum, as follows: CRC_errors - Bit 0 - Least Significant Bit runts - Bit 1 OOW_colls - Bit 2 align_errs - Bit 3 undefined - Bit 4 Giants - Bit 5 |
| INT rptrPortAlarmErrPortDisable | 1.3.6.1.4.1.52.4.1.1.1.4.3.3.1.12 | INTEGER | read-write | Set will permit a port to be disabled on an error alarm condition. Get will show whether the port disabling is allowed or not. |
| INT rptrPortAlarmBroadEnable | 1.3.6.1.4.1.52.4.1.1.1.4.3.3.1.13 | INTEGER | read-write | Get returns whether broadcast alarms are enabled/disabled. Set allows for enabling/disabling of broadcast alarms. |
| INT rptrPortAlarmBroadThreshold | 1.3.6.1.4.1.52.4.1.1.1.4.3.3.1.14 | INTEGER | read-write | The broadcase threshold represents the maximum number of broadcasts that are allowed during the time base before an alarm is generated. |
| INT rptrPortAlarmBroadPortDisable | 1.3.6.1.4.1.52.4.1.1.1.4.3.3.1.15 | INTEGER | read-write | Set will permit a port to be disabled on a broadcast alarm condition. Get will show whether the port disabling is allowed or not. |
| rptrPortRedundTable | 1.3.6.1.4.1.52.4.1.1.1.4.3.4 | not-accessible | A list of port redundancy objects for this repeater node. | |
| rptrPortRedundEntry | 1.3.6.1.4.1.52.4.1.1.1.4.3.4.1 | not-accessible | An entry containing objects pertaining to port redundancy for a port group. | |
| INT rptrPortRedundPortId | 1.3.6.1.4.1.52.4.1.1.1.4.3.4.1.1 | INTEGER | read-only | Returns an index to a port for which the information in this table pertains. |
| INT rptrPortRedundPortGrpId | 1.3.6.1.4.1.52.4.1.1.1.4.3.4.1.2 | INTEGER | read-only | Returns an index to a port group for which the information in this table pertains. |
| INT rptrPortRedundCrctNum | 1.3.6.1.4.1.52.4.1.1.1.4.3.4.1.3 | INTEGER | read-write | Get/Set redundant circuit number of redundant circuit that port is or is to be associated with. |
| INT rptrPortRedundType | 1.3.6.1.4.1.52.4.1.1.1.4.3.4.1.4 | INTEGER | read-write | Get/Set redundant port type. |
| INT rptrPortRedundStatus | 1.3.6.1.4.1.52.4.1.1.1.4.3.4.1.5 | INTEGER | read-write | Get/Set redundant port status. |
| rptrPortSrcAddrTable | 1.3.6.1.4.1.52.4.1.1.1.4.3.5 | not-accessible | A list of port source address objects for this repeater node. | |
| rptrPortSrcAddrEntry | 1.3.6.1.4.1.52.4.1.1.1.4.3.5.1 | not-accessible | An entry containing objects pertaining to port source address objects for a port group. | |
| INT rptrPortSrcAddrPortId | 1.3.6.1.4.1.52.4.1.1.1.4.3.5.1.1 | INTEGER | read-only | Returns an index to a port for which the information in this table pertains. |
| INT rptrPortSrcAddrPortGrpId | 1.3.6.1.4.1.52.4.1.1.1.4.3.5.1.2 | INTEGER | read-only | Returns an index to a port group for which the information in this table pertains. |
| INT rptrPortSrcAddrTopoState | 1.3.6.1.4.1.52.4.1.1.1.4.3.5.1.3 | INTEGER | read-only | Returns the topological state of the port. |
| INT rptrPortSrcAddrForceTrunk | 1.3.6.1.4.1.52.4.1.1.1.4.3.5.1.4 | INTEGER | read-write | When this object is set to Force it causes the port to be placed into a Trunk topological state whether the network traffic would warrant such a state or not. When this object is set to NoForce it allows the port to assume the topological state it would naturally assume based on the network activity across it. When read this object reports the current setting. |
| INT rptrPortSrcAddrActiveUsers | 1.3.6.1.4.1.52.4.1.1.1.4.3.5.1.5 | INTEGER | read-only | Returns the total number of active users seen by this port. |
| rptrPortSrcAddrListTable | 1.3.6.1.4.1.52.4.1.1.1.4.3.6 | not-accessible | This table provides information about the source addresses that have been seen by the differnt ports. | |
| rptrPortSrcAddrListEntry | 1.3.6.1.4.1.52.4.1.1.1.4.3.6.1 | not-accessible | A specific source address that has been seen | |
| INT rptrPortSrcAddrListId | 1.3.6.1.4.1.52.4.1.1.1.4.3.6.1.1 | INTEGER | read-only | Returns an index associated with the number of address to be returned. |
| INT rptrPortSrcAddrListPortId | 1.3.6.1.4.1.52.4.1.1.1.4.3.6.1.2 | INTEGER | read-only | Returns an index to a port for which the information in this table pertains. |
| INT rptrPortSrcAddrListPortGrpId | 1.3.6.1.4.1.52.4.1.1.1.4.3.6.1.3 | INTEGER | read-only | Returns an index to a port group for which the information in this table pertains. |
| OCT rptrPortSrcAddrAddressList | 1.3.6.1.4.1.52.4.1.1.1.4.3.6.1.4 | OCTET STRING | read-only | Returns a source address seen on this port. |
| rptrPortHardwareTable | 1.3.6.1.4.1.52.4.1.1.1.4.3.7 | not-accessible | A list of port hardware objects for this repeater port. | |
| rptrPortHardwareEntry | 1.3.6.1.4.1.52.4.1.1.1.4.3.7.1 | not-accessible | An entry containing objects pertaining to port hardware for a hardware port group. | |
| INT rptrPortHardwarePortId | 1.3.6.1.4.1.52.4.1.1.1.4.3.7.1.1 | INTEGER | read-only | Returns an index to a port for which the information in this table pertains. |
| INT rptrPortHardwarePortGrpId | 1.3.6.1.4.1.52.4.1.1.1.4.3.7.1.2 | INTEGER | read-only | Returns an index to a port group for which the information in this table pertains. |
| INT rptrPortHardwareSegStatus | 1.3.6.1.4.1.52.4.1.1.1.4.3.7.1.3 | INTEGER | read-only | Returns port segmentation status. |
| INT rptrPortHardwareLinkStatus | 1.3.6.1.4.1.52.4.1.1.1.4.3.7.1.4 | INTEGER | read-only | Returns port link status. |
| rptrPortTrap | 1.3.6.1.4.1.52.4.1.1.1.4.3.8 | |||
| rptrPortHwTrapSet | 1.3.6.1.4.1.52.4.1.1.1.4.3.8.1 | |||
| rptrPortHwTrapTable | 1.3.6.1.4.1.52.4.1.1.1.4.3.8.1.1 | not-accessible | A list of trap enable/disable at the port level. | |
| rptrPortHwTrapEntry | 1.3.6.1.4.1.52.4.1.1.1.4.3.8.1.1.1 | not-accessible | Individual trap entries for port group enable/disable. | |
| INT rptrPortHwTrapSetPortId | 1.3.6.1.4.1.52.4.1.1.1.4.3.8.1.1.1.1 | INTEGER | read-only | Returns an index to a port for which the information in this table pertains. |
| INT rptrPortHwTrapSetPortGrpId | 1.3.6.1.4.1.52.4.1.1.1.4.3.8.1.1.1.2 | INTEGER | read-only | Returns an index to a port group for which the information in this table pertains. |
| INT rptrPortHwTrapSetLink | 1.3.6.1.4.1.52.4.1.1.1.4.3.8.1.1.1.3 | INTEGER | read-write | Enables and disables link traps for this port. |
| INT rptrPortHwTrapSetSeg | 1.3.6.1.4.1.52.4.1.1.1.4.3.8.1.1.1.4 | INTEGER | read-write | Enables and disables segmentation traps for this port. |
| rptrPortSaTrapSet | 1.3.6.1.4.1.52.4.1.1.1.4.3.8.2 | |||
| rptrPortSaTrapTable | 1.3.6.1.4.1.52.4.1.1.1.4.3.8.2.1 | not-accessible | A list of trap enable/disable at the port level | |
| rptrPortSaTrapEntry | 1.3.6.1.4.1.52.4.1.1.1.4.3.8.2.1.1 | not-accessible | Individual trap entries for port group enable/disable. | |
| INT rptrPortSaTrapSetPortId | 1.3.6.1.4.1.52.4.1.1.1.4.3.8.2.1.1.1 | INTEGER | read-only | Returns an index to a port for which the information in this table pertains. |
| INT rptrPortSaTrapSetPortGrpId | 1.3.6.1.4.1.52.4.1.1.1.4.3.8.2.1.1.2 | INTEGER | read-only | Returns an index to a port group for which the information in this table pertains. |
| INT rptrPortSaTrapSetSrcaddr | 1.3.6.1.4.1.52.4.1.1.1.4.3.8.2.1.1.3 | INTEGER | read-write | Enables and disables source address traps for this port. |
| rptrPortSecurity | 1.3.6.1.4.1.52.4.1.1.1.4.3.9 | |||
| rptrPortSecurityTable | 1.3.6.1.4.1.52.4.1.1.1.4.3.9.1 | not-accessible | This table defines status of the source lock security. | |
| rptrPortSecurityEntry | 1.3.6.1.4.1.52.4.1.1.1.4.3.9.1.1 | not-accessible | Defines lock status for this particular entry. | |
| INT rptrPortSecurityPortGrpId | 1.3.6.1.4.1.52.4.1.1.1.4.3.9.1.1.1 | INTEGER | read-only | The port Group ID for which this source address lock entry pertains. |
| INT rptrPortSecurityPortId | 1.3.6.1.4.1.52.4.1.1.1.4.3.9.1.1.2 | INTEGER | read-only | The port ID for which this source address lock entry pertains. |
| INT rptrPortSecurityLockStatus | 1.3.6.1.4.1.52.4.1.1.1.4.3.9.1.1.3 | INTEGER | read-write | Defines the lock status for this particular port entry. |
| OCT rptrPortSecurityLockAddAddress | 1.3.6.1.4.1.52.4.1.1.1.4.3.9.1.1.4 | OCTET STRING | read-write | Setting a value to this object will cause a new entry to be added to the rptrPortSecurityListTable. When read this object will display an OCTET STRING of SIZE 6 with each octet containing a 0. In general it is possible to add addresses at anytime. However there are several instances where the firmware and or hardware can not support the operation. In these instances an error will be returned if a addition is attempted. |
| OCT rptrPortSecurityLockDelAddress | 1.3.6.1.4.1.52.4.1.1.1.4.3.9.1.1.5 | OCTET STRING | read-write | Setting a value to this object will cause corresponding entry in the rptrPortSecurityListTable to be deleted. When read this object returns an OCTET STRING of length 6 with each octet having the value '0'. In general it is possible to delete locked addresses at any time. however there are instances where it is not supported in which case an error will be returned. |
| INT rptrPortSecurityDisableOnViolation | 1.3.6.1.4.1.52.4.1.1.1.4.3.9.1.1.6 | INTEGER | read-write | Designates whether port is disabled if its source address is violated. A source address violation occurs when a address is detected which is not in the source address list for this port. If the port is disabled due to the source address violation it can be enabled by setting rptrPortMgmtAdminState. |
| INT rptrPortSecurityFullSecEnabled | 1.3.6.1.4.1.52.4.1.1.1.4.3.9.1.1.7 | INTEGER | read-write | A port that is set to full security and is locked will scramble ALL packets, which are not contained in the expected address list, including broadcasts and multicasts. A port that is set to partial security will allow broadcasts and multicasts to repeat unscrambled. |
| INT rptrPortSecuritySecureState | 1.3.6.1.4.1.52.4.1.1.1.4.3.9.1.1.8 | INTEGER | read-only | The secure state of the port. If the port is secure(1), it can be locked in order to enable security. A nonSecure(2) port cannot be locked. |
| INT rptrPortSecurityForceNonSecure | 1.3.6.1.4.1.52.4.1.1.1.4.3.9.1.1.9 | INTEGER | read-write | The force non-secure state of port. If the port is Forced, Non-Secure via a value of forceNonSecure(2), it is put into a Non-Secure state, in which case it cannot be locked. If a port is not forced noForce(1), then it will take on its natural state, according to the traffic flow on the port. |
| INT rptrPortSecurityLearnState | 1.3.6.1.4.1.52.4.1.1.1.4.3.9.1.1.10 | INTEGER | read-write | The learn state of the port. This object will only be applied to a port that is unlocked. If set to learn(1), all addresses are deleted on the port and learning begins once again. If it is set to noLearn(2), learning stops on the port. |
| INT rptrPortSecurityLearnMode | 1.3.6.1.4.1.52.4.1.1.1.4.3.9.1.1.11 | INTEGER | read-write | The learn mode of the port. If set to oneTime(1), the port is capable of learning two addresses and securing on both destination and source addresses (upon locking port). If set to continuous(2), all addresses are initially deleted and the port continuously replaces the existing secure source address with the latest source address it sees. |
| rptrPortSecurityListTable | 1.3.6.1.4.1.52.4.1.1.1.4.3.9.2 | not-accessible | This table defines a list of all source address locks maintained for the specified port. | |
| rptrPortSecurityListEntry | 1.3.6.1.4.1.52.4.1.1.1.4.3.9.2.1 | not-accessible | An entry containing objects pertaining to source address locks for a port group. | |
| INT rptrPortSecurityListPortGrpId | 1.3.6.1.4.1.52.4.1.1.1.4.3.9.2.1.1 | INTEGER | read-only | The port group for which this security list entry pertains. |
| INT rptrPortSecurityListPortId | 1.3.6.1.4.1.52.4.1.1.1.4.3.9.2.1.2 | INTEGER | read-only | The port ID for which this source address lock list pertains. |
| INT rptrPortSecurityListIndex | 1.3.6.1.4.1.52.4.1.1.1.4.3.9.2.1.3 | INTEGER | read-only | A unique index for the source address entries. |
| OCT rptrPortSecurityListAddress | 1.3.6.1.4.1.52.4.1.1.1.4.3.9.2.1.4 | OCTET STRING | read-only | Defines the particular source address that has been locked. |
| rptrPortAssoc | 1.3.6.1.4.1.52.4.1.1.1.4.4 | |||
| rptrPortAssocTable | 1.3.6.1.4.1.52.4.1.1.1.4.4.1 | not-accessible | This table defines the port association for those switching MIMs that support this functionality. | |
| rptrPortAssocEntry | 1.3.6.1.4.1.52.4.1.1.1.4.4.1.1 | not-accessible | Describes a particular port association entry. | |
| INT rptrPortAssocBoard | 1.3.6.1.4.1.52.4.1.1.1.4.4.1.1.1 | INTEGER | read-only | The board number for which this port association information pertains. |
| INT rptrPortAssocStatus | 1.3.6.1.4.1.52.4.1.1.1.4.4.1.1.2 | INTEGER | read-write | This object describes the status of the user selectable port. On a TPXMIM34 this is port 13 which may either be an EPIM or default configuration. A value of defaultPort(1) restores the default configuration. A value of otherPort(2) may imply the use of the EPIM connection. |
RFC description
Cabletron enterprise repeater management providing network hub status, configuration, and performance monitoring.
Start monitoring vendor-neutral, standards-based MIB (RFC 1516/IEEE 802.3), Ethernet repeater hubs (port status/collision statistics) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.