All MIBs › REPEATER-MIB
Category: Legacy Hubs and Repeaters
Description: Manages IEEE 802.3 Ethernet repeater (hub) port statistics and configuration per IETF standards.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is REPEATER-MIB?
REPEATER-MIB is grounded in the IETF standard for managing IEEE 802.3 Ethernet repeaters (hubs), though this instance shows Cabletron-specific OID branch usage alongside the standard objects. It exposes per-port and per-board configuration and status (port enable, on/off, and operational state, board mapping) plus packet-level statistics such as total packets, bytes, collisions, and alignment/other errors. For hardware status monitoring, it lets an administrator confirm whether repeater ports are enabled and operationally up, and track rising error/collision counts that signal a failing port, bad cable, or faulty NIC. It predates and complements the modern interfaces MIB (IF-MIB), sharing similar operational-status concepts for shared-media hub hardware. It's typically deployed on legacy Ethernet hub/repeater hardware, including Cabletron repeater products, in older LAN wiring closets. Engineers can download the REPEATER-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in REPEATER-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Ethernet repeater/hub
- Cabletron repeater hardware
Monitoring Examples
Comparing rptrMgmtPortsEnable against rptrMgmtPortsOn for a given board reveals whether a configured port has failed to come up. rptrPktStatsColls and rptrPktStatsErrors climbing quickly relative to rptrPktStatsPackets on one port point to a duplex mismatch or bad cable causing excessive collisions on that segment. rptrMgmtBoardMap and rptrMgmtInterfaceNum let an operator map the physical repeater board/port numbering to the logical interface used elsewhere in management tools.
What Can Be Monitored
- port enable/operational state
- packet counts
- byte counts
- collision counts
- error/alignment counts
- board-to-port mapping
This MIB depends on
Related MIBs
Imported Objects
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| cabletron | 1.3.6.1.4.1.52 | |||
| mibs | 1.3.6.1.4.1.52.4 | |||
| ctron | 1.3.6.1.4.1.52.4.1 | |||
| ctphysical | 1.3.6.1.4.1.52.4.1.1 | |||
| repeater | 1.3.6.1.4.1.52.4.1.1.1 | |||
| repeaterRev4 | 1.3.6.1.4.1.52.4.1.1.1.4 | |||
| rptr | 1.3.6.1.4.1.52.4.1.1.1.4.1 | |||
| rptrMgmt | 1.3.6.1.4.1.52.4.1.1.1.4.1.1 | |||
| STR rptrMgmtName | 1.3.6.1.4.1.52.4.1.1.1.4.1.1.1 | DisplayString | read-write | The ASCII name assigned to this network. |
| INT rptrMgmtPortCount | 1.3.6.1.4.1.52.4.1.1.1.4.1.1.2 | INTEGER | read-only | Total number of ports residing on this lan segment. |
| INT rptrMgmtPortsEnable | 1.3.6.1.4.1.52.4.1.1.1.4.1.1.3 | INTEGER | read-write | Setting this object to Enable will cause all the ports residing in this network segment to be enabled. Setting this object to noEnable will have no effect. When read this object will always return noEnable. |
| INT rptrMgmtPortsOn | 1.3.6.1.4.1.52.4.1.1.1.4.1.1.4 | INTEGER | read-only | Get the total number of ON ports in this network. |
| INT rptrMgmtPortsOper | 1.3.6.1.4.1.52.4.1.1.1.4.1.1.5 | INTEGER | read-only | Get the number of operational ports in this network. |
| INT rptrMgmtBoardMap | 1.3.6.1.4.1.52.4.1.1.1.4.1.1.6 | INTEGER | read-only | Get a map of the chassis slots occupied by the boards in this network. |
| INT rptrMgmtInterfaceNum | 1.3.6.1.4.1.52.4.1.1.1.4.1.1.7 | INTEGER | read-only | Get the MIBII interface number of this network. A return of zero will mean this network is not associated with a MIBII interface. |
| rptrStats | 1.3.6.1.4.1.52.4.1.1.1.4.1.2 | |||
| rptrPktStats | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.1 | |||
| CTR rptrPktStatsPackets | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.1.1 | Counter | read-only | Get this repeater's total received packets. |
| CTR rptrPktStatsBytes | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.1.2 | Counter | read-only | Get this repeater's total received bytes. |
| CTR rptrPktStatsColls | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.1.3 | Counter | read-only | Get this repeater's total collisions. |
| CTR rptrPktStatsErrors | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.1.4 | Counter | read-only | Get this repeater's total errors. |
| CTR rptrPktStatsAlign | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.1.5 | Counter | read-only | Get this repeater's total frame alignment errors. |
| CTR rptrPktStatsCRC | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.1.6 | Counter | read-only | Get this repeater's total CRC errors. |
| CTR rptrPktStatsOOW | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.1.7 | Counter | read-only | Get this repeater's total out-of-window collisions. |
| CTR rptrPktStatsNoRsc | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.1.8 | Counter | read-only | This counter is the number of packets on this network that the hardware has processed that the management has either not seen yet, in the case of an active network, or has missed missed all together, in the case of a once active network. |
| rptrProtocols | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.2 | |||
| CTR rptrProtocolsOSI | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.2.1 | Counter | read-only | Get this repeater's total received OSI packets. |
| CTR rptrProtocolsNovell | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.2.2 | Counter | read-only | Get this repeater's total received Novell packets. |
| CTR rptrProtocolsBanyan | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.2.3 | Counter | read-only | Get this repeater's total received Banyan packets. |
| CTR rptrProtocolsDECNet | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.2.4 | Counter | read-only | Get this repeater's total received DECNet packets. |
| CTR rptrProtocolsXNS | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.2.5 | Counter | read-only | Get this repeater's total received XNS packets. |
| CTR rptrProtocolsIP | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.2.6 | Counter | read-only | Get this repeater's total received TCP/IP packets. |
| CTR rptrProtocolsCtron | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.2.7 | Counter | read-only | Get this repeater's total received CTRON Management packets. |
| CTR rptrProtocolsAppletalk | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.2.8 | Counter | read-only | Get this repeater's total received Appletalk packets. |
| CTR rptrProtocolsOther | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.2.9 | Counter | read-only | Get this repeater's total received unknown protocol packets. |
| rptrFrameSizes | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.3 | |||
| CTR rptrFrameSzRunt | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.3.1 | Counter | read-only | Get this repeater's total received packets of size less than 64 bytes. |
| CTR rptrFrameSz64To127 | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.3.2 | Counter | read-only | Get this repeater's total received packets of size between 64 and 127 bytes. |
| CTR rptrFrameSz128To255 | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.3.3 | Counter | read-only | Get this repeater's total received packets of size between 128 and 255 bytes. |
| CTR rptrFrameSz256To511 | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.3.4 | Counter | read-only | Get this repeater's total received packets of size between 256 and 511 bytes. |
| CTR rptrFrameSz512To1023 | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.3.5 | Counter | read-only | Get this repeater's total received packets of size between 512 and 1023 bytes. |
| CTR rptrFrameSz1024To1518 | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.3.6 | Counter | read-only | Get this repeater's total received packets of size between 1024 and 1518 bytes. |
| CTR rptrFrameSzGiant | 1.3.6.1.4.1.52.4.1.1.1.4.1.2.3.7 | Counter | read-only | Get this repeater's total received packets of size greater than 1518 bytes. |
| rptrAlarms | 1.3.6.1.4.1.52.4.1.1.1.4.1.3 | |||
| INT rptrAlarmsTrafEnable | 1.3.6.1.4.1.52.4.1.1.1.4.1.3.1 | INTEGER | read-write | Get returns whether traffic alarms are enabled/disabled. Set allows for enabling/disabling of traffic alarms. |
| INT rptrAlarmsTrafThreshold | 1.3.6.1.4.1.52.4.1.1.1.4.1.3.2 | INTEGER | read-write | Get/Set packet threshold within the timebase that will cause an alarm. |
| INT rptrAlarmsCollEnable | 1.3.6.1.4.1.52.4.1.1.1.4.1.3.3 | INTEGER | read-write | Get returns whether collision alarms are enabled/disabled. Set allows for enabling/disabling of collision alarms. |
| INT rptrAlarmsCollThreshold | 1.3.6.1.4.1.52.4.1.1.1.4.1.3.4 | INTEGER | read-write | Get/Set the number of collisions per good packet within the timebase that will cause an alarm. |
| INT rptrAlarmsErrEnable | 1.3.6.1.4.1.52.4.1.1.1.4.1.3.5 | INTEGER | read-write | Get returns whether error alarms are enabled/disabled. Set allows for enabling/disabling of error alarms. |
| INT rptrAlarmsErrThreshold | 1.3.6.1.4.1.52.4.1.1.1.4.1.3.6 | INTEGER | read-write | Get/Set the percentage of errors per good packet within the timebase that will cause an alarm. |
| INT rptrAlarmsErrSource | 1.3.6.1.4.1.52.4.1.1.1.4.1.3.7 | INTEGER | read-write | Get/Set a bit encoded map of which errors to include in the error sum, as follows: CRC_errors - Bit 0 - Least Significant Bit runts - Bit 1 OOW_colls - Bit 2 align_errs - Bit 3 No_resource - Bit 4 Giants - Bit 5 |
| INT rptrAlarmsAlarmTimebase | 1.3.6.1.4.1.52.4.1.1.1.4.1.3.8 | INTEGER | read-write | Get/Set alarm timebase. |
| rptrRedundancy | 1.3.6.1.4.1.52.4.1.1.1.4.1.4 | |||
| rptrRedund | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.1 | |||
| INT rptrRedundReset | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.1.1 | INTEGER | read-write | If this object is set to Reset it will cause a reset of the redundancy object to occur. Setting this object to NoReset will do nothing. This object will always be read as NoReset. |
| INT rptrRedundPollInterval | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.1.2 | INTEGER | read-write | Get/Set the number of seconds between polls for redundancy. |
| STR rptrRedundTestTOD | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.1.3 | DisplayString | read-write | Get/Set the time of day at which the redundant circuits will be tested. The format of the time string is hh:mm:ss. |
| INT rptrRedundPerformTest | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.1.4 | INTEGER | read-write | If this object is set to Test it will cause a test of the redundant circuits to be performed. Setting this object to NoTest will have no effect. When read this object will always return NoTest. |
| INT rptrRedundMaxCrcts | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.1.5 | INTEGER | read-only | Returns the maximum number of circuits which may exist on this network. |
| rptrRedundCrctTable | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.2 | not-accessible | A list of redundant circuit objects for this repeater. | |
| rptrRedundCrctEntry | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.2.1 | not-accessible | A list of objects for a particular redundant circuit. | |
| INT rptrRedundCrctId | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.2.1.1 | INTEGER | read-only | Returns the index for a member circuit in the table of redundant circuits. |
| OCT rptrRedundCrctName | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.2.1.2 | OCTET STRING | read-write | Get/Set the name of the indicated circuit. |
| INT rptrRedundCrctRetrys | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.2.1.3 | INTEGER | read-write | Get/Set the the number of unanswered polls allowed for the circuit. |
| INT rptrRedundCrctNumBPs | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.2.1.4 | INTEGER | read-only | Get the number of board/port combinations associated with the circuit. |
| INT rptrRedundCrctNumAddr | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.2.1.5 | INTEGER | read-only | Get the number of IP Addresses associated with the circuit. |
| IP rptrRedundCrctAddAddr | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.2.1.6 | IpAddress | read-write | Add an IP Address to the polling list for the indicated circuit. |
| IP rptrRedundCrctDelAddr | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.2.1.7 | IpAddress | read-write | Delete an IP Address from the polling list of the indicated circuit. |
| INT rptrRedundCrctEnable | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.2.1.8 | INTEGER | read-write | If this object is set to Enable, the circuit is enabled. If this object is set to Disable, the circuit is disbabled. When read, this object returns the state of the object based on the last request made. |
| INT rptrRedundCrctReset | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.2.1.9 | INTEGER | read-write | If this object is set to Reset, the circuit is reset. All of the circuit's associated boards and ports are returned to NOT_USED, any associated IP Addresses are purged from the circuit's address list, the name is cleared, and the retry count is reset to a default value. Setting this object to NoReset has no effect. When read, NoReset is always returned. |
| rptrRedundPortTable | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.3 | not-accessible | A list of redundant port objects for this repeater. | |
| rptrRedundPortEntry | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.3.1 | not-accessible | A redundant port entry containing objects pertaining to a particular redundant port. | |
| INT rptrRedundPortId | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.3.1.1 | INTEGER | read-only | A unique value identifying an element in a sequence of member ports which belong to a circuit in the table of redundant circuits. This value is not a port number; rather it is a value which goes from 1 to the maximum number of ports which may be included in a redundant circuit. |
| INT rptrRedundPortCrctId | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.3.1.2 | INTEGER | read-only | A unique value identifying a member circuit in the table of redundant circuits. This value is similar to rptrRedundCrctId. |
| INT rptrRedundPortNum | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.3.1.3 | INTEGER | read-only | Returns the port number of a member port belonging to a redundant circuit. |
| INT rptrRedundPortBoardNum | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.3.1.4 | INTEGER | read-only | Returns the board number of a member port belonging to a redundant circuit. |
| INT rptrRedundPortType | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.3.1.5 | INTEGER | read-only | Return the state of a port associated with the indicated circuit. |
| rptrRedundAddrTable | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.4 | not-accessible | ||
| rptrRedundAddrEntry | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.4.1 | not-accessible | ||
| INT rptrRedundAddrId | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.4.1.1 | INTEGER | read-only | A unique value identifying an element in a sequence of member IP Addresses which belong to a circuit in the table of redundant circuits. This value goes from 1 to the maximum number of IP Addresses which may be included in a redundant circuit. |
| INT rptrRedundAddrCrctId | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.4.1.2 | INTEGER | read-only | A unique value identifying a member circuit in the table of redundant circuits. This value is similar to rptrRedundCrctId. |
| IP rptrRedundAddrIPAddr | 1.3.6.1.4.1.52.4.1.1.1.4.1.4.4.1.3 | IpAddress | read-only | Returns an IP Address associated with the indicated circuit. |
| rptrSourceAddress | 1.3.6.1.4.1.52.4.1.1.1.4.1.5 | |||
| rptrSrcAddrListTable | 1.3.6.1.4.1.52.4.1.1.1.4.1.5.1 | not-accessible | ||
| rptrSrcAddrListEntry | 1.3.6.1.4.1.52.4.1.1.1.4.1.5.1.1 | not-accessible | ||
| INT rptrSrcAddrListId | 1.3.6.1.4.1.52.4.1.1.1.4.1.5.1.1.1 | INTEGER | read-only | Returns an index into a table of source address seen by this repeater. |
| OCT rptrSrcAddrAddressList | 1.3.6.1.4.1.52.4.1.1.1.4.1.5.1.1.2 | OCTET STRING | read-only | Returns a source address seen by this repeater. |
| rptrSrcAddrSrcTable | 1.3.6.1.4.1.52.4.1.1.1.4.1.5.2 | not-accessible | ||
| rptrSrcAddrSrcTableEntry | 1.3.6.1.4.1.52.4.1.1.1.4.1.5.2.1 | not-accessible | ||
| OCT rptrSrcAddrSrcTableEntryId | 1.3.6.1.4.1.52.4.1.1.1.4.1.5.2.1.1 | OCTET STRING | read-only | Returns the source address to which this table's information pertains. |
| INT rptrSrcAddrSrcTableEntryPort | 1.3.6.1.4.1.52.4.1.1.1.4.1.5.2.1.2 | INTEGER | read-only | Returns the port# of the port that sourced the source address. |
| INT rptrSrcAddrSrcTableEntryPortGroup | 1.3.6.1.4.1.52.4.1.1.1.4.1.5.2.1.3 | INTEGER | read-only | Returns the port group# of the port that sourced the source address. |
| rptrSrcAddrMgmt | 1.3.6.1.4.1.52.4.1.1.1.4.1.5.3 | |||
| INT rptrSrcAddrMgmtSrcAgeInterval | 1.3.6.1.4.1.52.4.1.1.1.4.1.5.3.1 | INTEGER | read-write | Get/Set source addressing ageing interval. |
| INT rptrSrcAddrMgmtPortLock | 1.3.6.1.4.1.52.4.1.1.1.4.1.5.3.2 | INTEGER | read-write | Setting this object to Lock will activate the network port security lock. |
| INT rptrSrcAddrMgmtActiveUsers | 1.3.6.1.4.1.52.4.1.1.1.4.1.5.3.3 | INTEGER | read-only | Get the number of active users on this network. |
| rptrPortGroup | 1.3.6.1.4.1.52.4.1.1.1.4.2 | |||
| rptrPortGrpMgmtTable | 1.3.6.1.4.1.52.4.1.1.1.4.2.1 | not-accessible | ||
| rptrPortGrpMgmtEntry | 1.3.6.1.4.1.52.4.1.1.1.4.2.1.1 | not-accessible | ||
| INT rptrPortGrpMgmtGrpId | 1.3.6.1.4.1.52.4.1.1.1.4.2.1.1.1 | INTEGER | read-only | Returns an index to a port group for which the information in this table pertains. |
| STR rptrPortGrpMgmtName | 1.3.6.1.4.1.52.4.1.1.1.4.2.1.1.2 | DisplayString | read-write | Gets/Sets a name for the specified port group. |
| INT rptrPortGrpMgmtPortCount | 1.3.6.1.4.1.52.4.1.1.1.4.2.1.1.3 | INTEGER | read-only | Get total number of ports contained on the board. |
| INT rptrPortGrpMgmtPortsEnable | 1.3.6.1.4.1.52.4.1.1.1.4.2.1.1.4 | INTEGER | read-write | Setting this object to Enable will cause all the ports residing in this network segment to be enabled. Setting this object to noEnable will have no effect. When read this object will always return noEnable. |
| INT rptrPortGrpMgmtPortsOn | 1.3.6.1.4.1.52.4.1.1.1.4.2.1.1.5 | INTEGER | read-only | Get total number of ON ports on the board. |
| INT rptrPortGrpMgmtPortsOper | 1.3.6.1.4.1.52.4.1.1.1.4.2.1.1.6 | INTEGER | read-only | Get total number of operational ports on the board. |
| rptrPortGrpStats | 1.3.6.1.4.1.52.4.1.1.1.4.2.2 | |||
| rptrPortGrpPktStatsTbl | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.1 | not-accessible | ||
| rptrPortGrpPktStatsEntry | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.1.1 | not-accessible | ||
| INT rptrPortGrpPktStatsId | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.1.1.1 | INTEGER | read-only | Returns an index to a port group for which the information in this table pertains. |
| CTR rptrPortGrpPktStatsPkts | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.1.1.2 | Counter | read-only | Return this port group's total received packets. |
| CTR rptrPortGrpPktStatsBytes | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.1.1.3 | Counter | read-only | Return this port group's total received bytes. |
| CTR rptrPortGrpPktStatsColls | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.1.1.4 | Counter | read-only | Return this port group's total collisions. |
| CTR rptrPortGrpPktStatsErrors | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.1.1.5 | Counter | read-only | Return this port group's total errors. |
| CTR rptrPortGrpPktStatsAlign | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.1.1.6 | Counter | read-only | Return this port group's total frame alignment errors. |
| CTR rptrPortGrpPktStatsCRC | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.1.1.7 | Counter | read-only | Return this port group's total CRC errors. |
| CTR rptrPortGrpPktStatsOOW | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.1.1.8 | Counter | read-only | Return this port group's total out-of-window collisions. |
| rptrPortGrpProtocolTbl | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.2 | not-accessible | ||
| rptrPortGrpProtocolEntry | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.2.1 | not-accessible | ||
| INT rptrPortGrpProtocolId | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.2.1.1 | INTEGER | read-only | Returns an index to a port group for which the information in this table pertains. |
| CTR rptrPortGrpProtocolOSI | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.2.1.2 | Counter | read-only | Return this port group's total received OSI packets. |
| CTR rptrPortGrpProtocolNovell | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.2.1.3 | Counter | read-only | Return this port group's total received Novell packets. |
| CTR rptrPortGrpProtocolBanyan | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.2.1.4 | Counter | read-only | Return this port group's total received Banyan packets. |
| CTR rptrPortGrpProtocolDECNet | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.2.1.5 | Counter | read-only | Return this port group's total received DECNet packets. |
| CTR rptrPortGrpProtocolXNS | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.2.1.6 | Counter | read-only | Return this port group's total received XNS packets. |
| CTR rptrPortGrpProtocolIP | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.2.1.7 | Counter | read-only | Return this port group's total received TCP/IP packets. |
| CTR rptrPortGrpProtocolCtron | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.2.1.8 | Counter | read-only | Return this port group's total received CTRON Management packets. |
| CTR rptrPortGrpProtocolAppletalk | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.2.1.9 | Counter | read-only | Return this port group's total received Appletalk packets. |
| CTR rptrPortGrpProtocolOther | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.2.1.10 | Counter | read-only | Return this port group's total received unknown protocol packets. |
| rptrPortGrpFrameSzTbl | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.3 | not-accessible | ||
| rptrPortGrpFrameSzEntry | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.3.1 | not-accessible | ||
| INT rptrPortGrpFrameSzId | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.3.1.1 | INTEGER | read-only | Returns an index to a port group for which the information in this table pertains. |
| CTR rptrPortGrpFrameSzRunt | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.3.1.2 | Counter | read-only | Return this port group's total received packets of size less than 64 bytes. |
| CTR rptrPortGrpFrameSz64To127 | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.3.1.3 | Counter | read-only | Return this port group's total received packets of size between 64 and 127 bytes. |
| CTR rptrPortGrpFrameSz128To255 | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.3.1.4 | Counter | read-only | Return this port group's total received packets of size between 128 and 255 bytes. |
| CTR rptrPortGrpFrameSz256To511 | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.3.1.5 | Counter | read-only | Return this port group's total received packets of size between 256 and 511 bytes. |
| CTR rptrPortGrpFrameSz512To1023 | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.3.1.6 | Counter | read-only | Return this port group's total received packets of size between 512 and 1023 bytes. |
| CTR rptrPortGrpFrameSz1024To1518 | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.3.1.7 | Counter | read-only | Return this port group's total received packets of size between 1024 and 1518 bytes. |
| CTR rptrPortGrpFrameSzGiant | 1.3.6.1.4.1.52.4.1.1.1.4.2.2.3.1.8 | Counter | read-only | Return this port group's total received packets of size greater than 1518 bytes. |
| rptrPortGrpAlarmTable | 1.3.6.1.4.1.52.4.1.1.1.4.2.3 | not-accessible | ||
| rptrPortGrpAlarmEntry | 1.3.6.1.4.1.52.4.1.1.1.4.2.3.1 | not-accessible | ||
| INT rptrPortGrpAlarmId | 1.3.6.1.4.1.52.4.1.1.1.4.2.3.1.1 | INTEGER | read-only | Returns an index to a port group for which the information in this table pertains. |
| INT rptrPortGrpAlarmTrafEnable | 1.3.6.1.4.1.52.4.1.1.1.4.2.3.1.2 | INTEGER | read-write | Get returns whether traffic alarms are enabled/disabled. Set allows for enabling/disabling of traffic alarms. |
| INT rptrPortGrpAlarmTrafThreshold | 1.3.6.1.4.1.52.4.1.1.1.4.2.3.1.3 | INTEGER | read-write | Get/Set packet threshold within the timebase that will cause an alarm. |
| INT rptrPortGrpAlarmTrafGrpDisable | 1.3.6.1.4.1.52.4.1.1.1.4.2.3.1.4 | INTEGER | read-write | Set will permit a port group to be disabled on a traffic alarm condition. Get will show whether the port group disabling is allowed or not. |
| INT rptrPortGrpAlarmCollEnable | 1.3.6.1.4.1.52.4.1.1.1.4.2.3.1.5 | INTEGER | read-write | Get returns whether collision alarms are enabled/disabled. Set allows for enabling/disabling of collision alarms |
| INT rptrPortGrpAlarmCollThreshold | 1.3.6.1.4.1.52.4.1.1.1.4.2.3.1.6 | INTEGER | read-write | Get/Set the number of collisions per good packet within the timebase that will cause an alarm. |
| INT rptrPortGrpAlarmCollBdDisable | 1.3.6.1.4.1.52.4.1.1.1.4.2.3.1.7 | INTEGER | read-write | Set will permit a board to be disabled on a collision alarm condition. Get will show whether the board disabling is allowed or not. |
| INT rptrPortGrpAlarmErrEnable | 1.3.6.1.4.1.52.4.1.1.1.4.2.3.1.8 | INTEGER | read-write | Get returns whether error alarms are enabled/disabled. Set allows for enabling/disabling of error alarms |
| INT rptrPortGrpAlarmErrThreshold | 1.3.6.1.4.1.52.4.1.1.1.4.2.3.1.9 | INTEGER | read-write | Get/Set the percentage of errors per good packet within the timebase that will cause an alarm. |
| INT rptrPortGrpAlarmErrSource | 1.3.6.1.4.1.52.4.1.1.1.4.2.3.1.10 | INTEGER | read-write | Get/Set a bit encoded map of which errors to include in the error sum, as follows: CRC_errors - Bit 0 - Least Significant Bit runts - Bit 1 OOW_colls - Bit 2 align_errs - Bit 3 undefined - Bit 4 Giants - Bit 5 |
| INT rptrPortGrpAlarmErrGrpDisable | 1.3.6.1.4.1.52.4.1.1.1.4.2.3.1.11 | INTEGER | read-write | Set will permit a port group to be disabled on an error alarm condition. Get will show whether the port group disabling is allowed or not. |
| rptrPortGrpSrcAddrTable | 1.3.6.1.4.1.52.4.1.1.1.4.2.4 | not-accessible | ||
| rptrPortGrpSrcAddrEntry | 1.3.6.1.4.1.52.4.1.1.1.4.2.4.1 | not-accessible | ||
| INT rptrPortGrpSrcAddrId | 1.3.6.1.4.1.52.4.1.1.1.4.2.4.1.1 | INTEGER | read-only | Returns an index to a port group for which the information in this table pertains. |
| INT rptrPortGrpSrcAddrActiveUsers | 1.3.6.1.4.1.52.4.1.1.1.4.2.4.1.2 | INTEGER | read-only | Returns the total number of active users seen by this port group. |
| rptrPort | 1.3.6.1.4.1.52.4.1.1.1.4.3 | |||
| rptrPortMgmtTable | 1.3.6.1.4.1.52.4.1.1.1.4.3.1 | not-accessible | ||
| rptrPortMgmtEntry | 1.3.6.1.4.1.52.4.1.1.1.4.3.1.1 | not-accessible | ||
| INT rptrPortMgmtPortId | 1.3.6.1.4.1.52.4.1.1.1.4.3.1.1.1 | INTEGER | read-only | Returns an index to a port for which the information in this table pertains. |
| INT rptrPortMgmtPortGrpId | 1.3.6.1.4.1.52.4.1.1.1.4.3.1.1.2 | INTEGER | read-only | Returns an index to a port group for which the information in this table pertains. |
| STR rptrPortMgmtName | 1.3.6.1.4.1.52.4.1.1.1.4.3.1.1.3 | DisplayString | read-write | Sets/Gets an ASCII name assigned to this port. |
| INT rptrPortMgmtAdminState | 1.3.6.1.4.1.52.4.1.1.1.4.3.1.1.4 | INTEGER | read-write | Setting this object to Enable will cause port to be enabled. Setting this object to Disable will cause the port to be disabled. When read this object will return the state of the object per the last request. |
| INT rptrPortMgmtOperState | 1.3.6.1.4.1.52.4.1.1.1.4.3.1.1.5 | INTEGER | read-only | Get port operational status. |
| OID prtrPortMgmtPortType | 1.3.6.1.4.1.52.4.1.1.1.4.3.1.1.6 | OBJECT IDENTIFIER | read-only | Uniquely defines the repeater port type. A authoritative identification for a port type. By convention, this value is alocated within the SMI enterprises subtree (1.3.6.1.4.1), and provides an easy and unambiguous means to determine the type of repeater port. |
| rptrPortStats | 1.3.6.1.4.1.52.4.1.1.1.4.3.2 | |||
| rptrPortPktStatsTbl | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.1 | not-accessible | ||
| rptrPortPktStatsEntry | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.1.1 | not-accessible | ||
| INT rptrPortPktStatsPortId | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.1.1.1 | INTEGER | read-only | Returns an index to a port for which the information in this table pertains. |
| INT rptrPortPktStatsPortGrpId | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.1.1.2 | INTEGER | read-only | Returns an index to a port group for which the information in this table pertains. |
| CTR rptrPortPktStatsPackets | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.1.1.3 | Counter | read-only | Get this port's total received packets. |
| CTR rptrPortPktStatsBytes | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.1.1.4 | Counter | read-only | Get this port's total received bytes. |
| CTR rptrPortPktStatsColls | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.1.1.5 | Counter | read-only | Get this port's total collisions. |
| CTR rptrPortPktStatsErrors | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.1.1.6 | Counter | read-only | Get this port's total errors. |
| CTR rptrPortPktStatsAlign | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.1.1.7 | Counter | read-only | Get this port's total frame alignment errors. |
| CTR rptrPortPktStatsCRC | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.1.1.8 | Counter | read-only | Get this port's total CRC errors. |
| CTR rptrPortPktStatsOOW | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.1.1.9 | Counter | read-only | Get this port's total out-of-window collisions. |
| rptrPortProtocolTbl | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.2 | not-accessible | ||
| rptrPortProtocolEntry | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.2.1 | not-accessible | ||
| INT rptrPortProtocolPortId | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.2.1.1 | INTEGER | read-only | Returns an index to a port for which the information in this table pertains. |
| INT rptrPortProtocolPortGrpId | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.2.1.2 | INTEGER | read-only | Returns an index to a port group for which the information in this table pertains. |
| CTR rptrPortProtocolOSI | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.2.1.3 | Counter | read-only | Get this port's total received OSI protocol packets. |
| CTR rptrPortProtocolNovell | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.2.1.4 | Counter | read-only | Get this port's total received Novell protocol packets. |
| CTR rptrPortProtocolBanyan | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.2.1.5 | Counter | read-only | Get this port's total received Banyan protocol packets. |
| CTR rptrPortProtocolDECNet | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.2.1.6 | Counter | read-only | Get this port's total received DECNet protocol packets. |
| CTR rptrPortProtocolXNS | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.2.1.7 | Counter | read-only | Get this port's total received XNS protocol packets. |
| CTR rptrPortProtocolIP | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.2.1.8 | Counter | read-only | Get this port's total received TCP/IP protocol packets. |
| CTR rptrPortProtocolCtron | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.2.1.9 | Counter | read-only | Get this port's total received CTRON Management protocol packets. |
| CTR rptrPortProtocolAppletalk | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.2.1.10 | Counter | read-only | Get this port's total received Appletalk protocol packets. |
| CTR rptrPortProtocolOther | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.2.1.11 | Counter | read-only | Get this port's total received unknown protocol packets. |
| rptrPortFrameSzTbl | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.3 | not-accessible | Description goes here. | |
| rptrPortFrameSzEntry | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.3.1 | not-accessible | Description goes here. | |
| INT rptrPortFrameSzPortId | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.3.1.1 | INTEGER | read-only | Returns an index to a port for which the information in this table pertains. |
| INT rptrPortFrameSzPortGrpId | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.3.1.2 | INTEGER | read-only | Returns an index to a port group for which the information in this table pertains. |
| CTR rptrPortFrameSzRunt | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.3.1.3 | Counter | read-only | Get this port's total received packets of size less than 64 bytes. |
| CTR rptrPortFrameSz64To127 | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.3.1.4 | Counter | read-only | Get this port's total received packets of size between 64 and 127 bytes. |
| CTR rptrPortFrameSz128To255 | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.3.1.5 | Counter | read-only | Get this port's total received packets of size between 128 and 255 bytes. |
| CTR rptrPortFrameSz256To511 | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.3.1.6 | Counter | read-only | Get this port's total received packets of size between 256 and 511 bytes. |
| CTR rptrPortFrameSz512To1023 | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.3.1.7 | Counter | read-only | Get this port's total received packets of size between 512 and 1023 bytes. |
| CTR rptrPortFrameSz1024To1518 | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.3.1.8 | Counter | read-only | Get this port's total received packets of size between 1024 and 1518 bytes. |
| CTR rptrPortFrameSzGiant | 1.3.6.1.4.1.52.4.1.1.1.4.3.2.3.1.9 | Counter | read-only | Get this port's total received packets of size greater than 1518 bytes. |
| rptrPortAlarmTable | 1.3.6.1.4.1.52.4.1.1.1.4.3.3 | not-accessible | ||
| rptrPortAlarmEntry | 1.3.6.1.4.1.52.4.1.1.1.4.3.3.1 | not-accessible | ||
| INT rptrPortAlarmPortId | 1.3.6.1.4.1.52.4.1.1.1.4.3.3.1.1 | INTEGER | read-only | Returns an index to a port for which the information in this table pertains. |
| INT rptrPortAlarmPortGrpId | 1.3.6.1.4.1.52.4.1.1.1.4.3.3.1.2 | INTEGER | read-only | Returns an index to a port group for which the information in this table pertains. |
| INT rptrPortAlarmTrafEnable | 1.3.6.1.4.1.52.4.1.1.1.4.3.3.1.3 | INTEGER | read-write | Get returns whether traffic alarms are enabled/disabled. Set allows for enabling/disabling of traffic alarms. |
| INT rptrPortAlarmTrafThreshold | 1.3.6.1.4.1.52.4.1.1.1.4.3.3.1.4 | INTEGER | read-write | Get/Set packet threshold within the timebase that will cause an alarm. |
| INT rptrPortAlarmTrafPortDisable | 1.3.6.1.4.1.52.4.1.1.1.4.3.3.1.5 | INTEGER | read-write | Set will permit a port to be disabled on a traffic alarm condition. Get will show whether the port disabling is allowed or not. |
| INT rptrPortAlarmCollEnable | 1.3.6.1.4.1.52.4.1.1.1.4.3.3.1.6 | INTEGER | read-write | Get returns whether collision alarms are enabled/disabled. Set allows for enabling/disabling of collision alarms. |
| INT rptrPortAlarmCollThreshold | 1.3.6.1.4.1.52.4.1.1.1.4.3.3.1.7 | INTEGER | read-write | Get/Set the number of collisions per good packet within the timebase that will cause an alarm. |
| INT rptrPortAlarmCollPortDisable | 1.3.6.1.4.1.52.4.1.1.1.4.3.3.1.8 | INTEGER | read-write | Set will permit a port to be disabled on a collision alarm condition. Get will show whether the port disabling is allowed or not. |
| INT rptrPortAlarmErrEnable | 1.3.6.1.4.1.52.4.1.1.1.4.3.3.1.9 | INTEGER | read-write | Get returns whether error alarms are enabled/disabled. Set allows for enabling/disabling of error alarms |
| INT rptrPortAlarmErrThreshold | 1.3.6.1.4.1.52.4.1.1.1.4.3.3.1.10 | INTEGER | read-write | Get/Set the percentage of errors per good packet within the timebase that will cause an alarm. |
| INT rptrPortAlarmErrSource | 1.3.6.1.4.1.52.4.1.1.1.4.3.3.1.11 | INTEGER | read-write | Get/Set a bit encoded map of which errors to include in the error sum, as follows: CRC_errors - Bit 0 - Least Significant Bit runts - Bit 1 OOW_colls - Bit 2 align_errs - Bit 3 undefined - Bit 4 Giants - Bit 5 |
| INT rptrPortAlarmErrPortDisable | 1.3.6.1.4.1.52.4.1.1.1.4.3.3.1.12 | INTEGER | read-write | Set will permit a port to be disabled on an error alarm condition. Get will show whether the port disabling is allowed or not. |
| rptrPortRedundTable | 1.3.6.1.4.1.52.4.1.1.1.4.3.4 | not-accessible | ||
| rptrPortRedundEntry | 1.3.6.1.4.1.52.4.1.1.1.4.3.4.1 | not-accessible | ||
| INT rptrPortRedundPortId | 1.3.6.1.4.1.52.4.1.1.1.4.3.4.1.1 | INTEGER | read-only | Returns an index to a port for which the information in this table pertains. |
| INT rptrPortRedundPortGrpId | 1.3.6.1.4.1.52.4.1.1.1.4.3.4.1.2 | INTEGER | read-only | Returns an index to a port group for which the information in this table pertains. |
| INT rptrPortRedundCrctNum | 1.3.6.1.4.1.52.4.1.1.1.4.3.4.1.3 | INTEGER | read-write | Get/Set redundant circuit number of redundant circuit that port is or is to be associated with. |
| INT rptrPortRedundType | 1.3.6.1.4.1.52.4.1.1.1.4.3.4.1.4 | INTEGER | read-write | Get/Set redundant port type. |
| INT rptrPortRedundStatus | 1.3.6.1.4.1.52.4.1.1.1.4.3.4.1.5 | INTEGER | read-write | Get/Set redundant port status. |
| rptrPortSrcAddrTable | 1.3.6.1.4.1.52.4.1.1.1.4.3.5 | not-accessible | ||
| rptrPortSrcAddrEntry | 1.3.6.1.4.1.52.4.1.1.1.4.3.5.1 | not-accessible | ||
| INT rptrPortSrcAddrPortId | 1.3.6.1.4.1.52.4.1.1.1.4.3.5.1.1 | INTEGER | read-only | Returns an index to a port for which the information in this table pertains. |
| INT rptrPortSrcAddrPortGrpId | 1.3.6.1.4.1.52.4.1.1.1.4.3.5.1.2 | INTEGER | read-only | Returns an index to a port group for which the information in this table pertains. |
| INT rptrPortSrcAddrTopoState | 1.3.6.1.4.1.52.4.1.1.1.4.3.5.1.3 | INTEGER | read-only | Returns the topological state of the port. |
| INT rptrPortSrcAddrForceTrunk | 1.3.6.1.4.1.52.4.1.1.1.4.3.5.1.4 | INTEGER | read-write | When this object is set to Force it causes the port to be placed into a Trunk topological state whether the network traffic would warrant such a state or not. When this object is set to NoForce it allows the port to assume the topological state it would naturally assume based on the network activity acrossed it. When read this object reports the current setting. |
| INT rptrPortSrcAddrActiveUsers | 1.3.6.1.4.1.52.4.1.1.1.4.3.5.1.5 | INTEGER | read-only | Returns the total number of active users seen by this port. |
| rptrPortSrcAddrListTable | 1.3.6.1.4.1.52.4.1.1.1.4.3.6 | not-accessible | ||
| rptrPortSrcAddrListEntry | 1.3.6.1.4.1.52.4.1.1.1.4.3.6.1 | not-accessible | ||
| INT rptrPortSrcAddrListId | 1.3.6.1.4.1.52.4.1.1.1.4.3.6.1.1 | INTEGER | read-only | Returns an index associated with the number of address to be returned. |
| INT rptrPortSrcAddrListPortId | 1.3.6.1.4.1.52.4.1.1.1.4.3.6.1.2 | INTEGER | read-only | Returns an index to a port for which the information in this table pertains. |
| INT rptrPortSrcAddrListPortGrpId | 1.3.6.1.4.1.52.4.1.1.1.4.3.6.1.3 | INTEGER | read-only | Returns an index to a port group for which the information in this table pertains. |
| OCT rptrPortSrcAddrAddressList | 1.3.6.1.4.1.52.4.1.1.1.4.3.6.1.4 | OCTET STRING | read-only | Returns a source address seen on this port. |
| rptrPortHardwareTable | 1.3.6.1.4.1.52.4.1.1.1.4.3.7 | not-accessible | ||
| rptrPortHardwareEntry | 1.3.6.1.4.1.52.4.1.1.1.4.3.7.1 | not-accessible | ||
| INT rptrPortHardwarePortId | 1.3.6.1.4.1.52.4.1.1.1.4.3.7.1.1 | INTEGER | read-only | Returns an index to a port for which the information in this table pertains. |
| INT rptrPortHardwarePortGrpId | 1.3.6.1.4.1.52.4.1.1.1.4.3.7.1.2 | INTEGER | read-only | Returns an index to a port group for which the information in this table pertains. |
| INT rptrPortHardwareSegStatus | 1.3.6.1.4.1.52.4.1.1.1.4.3.7.1.3 | INTEGER | read-only | Returns port segmentation status. |
| INT rptrPortHardwareLinkStatus | 1.3.6.1.4.1.52.4.1.1.1.4.3.7.1.4 | INTEGER | read-only | Returns port link status. |
RFC description
Defined in RFC 2108, manages repeater devices (IEEE 802.3 physical layer hubs) including port status, segment information, and diagnostics.
Start monitoring Ethernet repeater/hub, Cabletron repeater hardware (per-port status/collision statistics) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.