Nortel-Magellan-Passport-FrameRelayDteMIB

All MIBs › Nortel-Magellan-Passport-FrameRelayDteMIB

Category: Frame Relay

Description: Manages Nortel Magellan Passport Frame Relay DTE interface configuration and DLCI management.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Nortel-Magellan-Passport-FrameRelayDteMIB?

This MIB manages the Frame Relay DTE (user/access-side) interface and DLCI configuration on Nortel Magellan Passport multiservice switches. It exposes frDteIfEntryTable, which ties a Frame Relay DTE port to a standard interface index, and frDteCidDataTable holding customer identifier assignments per circuit. Monitoring focuses on interface and framer status at the customer-facing Frame Relay access edge - detecting physical line faults or misconfigured DLCIs before they cause a customer outage. It depends on conventions from the standard IETF interfaces model (ifIndex) as well as the shared Passport component/RowStatus framework. It is deployed at customer-facing Frame Relay access ports on Magellan Passport edge switches. Engineers can download the Nortel-Magellan-Passport-FrameRelayDteMIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in Nortel-Magellan-Passport-FrameRelayDteMIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Nortel Magellan Passport multiservice switch
Frame Relay access/edge port

Monitoring Examples

An operator polls frDteIfEntryTable/frDteIfEntryEntry, which correlates a Frame Relay DTE port to its interface index, alongside frDteCidDataTable/frDteCidDataEntry to see the frDteCustomerIdentifier assigned to that access circuit. The frDteFramer objects report the physical-layer/framer status underneath the DTE interface. A framer alarm, or a mismatch between the interface and DLCI state, indicates a physical line fault or misconfigured customer circuit at the frame relay access edge.

What Can Be Monitored

Frame Relay DTE interface state
customer identifier per circuit
framer/physical layer status
component row status

Imported Objects

From Nortel-Magellan-Passport-StandardTextualConventionsMIB

Counter32
DisplayString
Gauge32
Integer32
InterfaceIndex
PassportCounter64
RowStatus
StorageType
Unsigned32

From Nortel-Magellan-Passport-TextualConventionsMIB

DashedHexString
EnterpriseDateAndTime
HexString
Link
NonReplicated

From Nortel-Magellan-Passport-UsefulDefinitionsMIB

components	OBJECT-IDENTITY
passportMIBs	OBJECT-IDENTITY

From RFC-1212

OBJECT-TYPE

OIDs

OID symbolic	OID numeric	Type	Access	Description
frDte	1.3.6.1.4.1.562.2.4.1.101
frDteRowStatusTable	1.3.6.1.4.1.562.2.4.1.101.1		not-accessible	This entry controls the addition and deletion of frDte components.
frDteRowStatusEntry	1.3.6.1.4.1.562.2.4.1.101.1.1		not-accessible	A single entry in the table represents a single frDte component.
ROW frDteRowStatus	1.3.6.1.4.1.562.2.4.1.101.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of frDte components. These components can be added and deleted.
STR frDteComponentName	1.3.6.1.4.1.562.2.4.1.101.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO frDteStorageType	1.3.6.1.4.1.562.2.4.1.101.1.1.4	StorageType	read-only	This variable represents the storage type value for the frDte tables.
I32 frDteIndex	1.3.6.1.4.1.562.2.4.1.101.1.1.10	Integer32	not-accessible	This variable represents the index for the frDte tables.
frDteFramer	1.3.6.1.4.1.562.2.4.1.101.2
frDteFramerRowStatusTable	1.3.6.1.4.1.562.2.4.1.101.2.1		not-accessible	This entry controls the addition and deletion of frDteFramer components.
frDteFramerRowStatusEntry	1.3.6.1.4.1.562.2.4.1.101.2.1.1		not-accessible	A single entry in the table represents a single frDteFramer component.
ROW frDteFramerRowStatus	1.3.6.1.4.1.562.2.4.1.101.2.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of frDteFramer components. These components can be added and deleted.
STR frDteFramerComponentName	1.3.6.1.4.1.562.2.4.1.101.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO frDteFramerStorageType	1.3.6.1.4.1.562.2.4.1.101.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the frDteFramer tables.
NON frDteFramerIndex	1.3.6.1.4.1.562.2.4.1.101.2.1.1.10	NonReplicated	not-accessible	This variable represents the index for the frDteFramer tables.
frDteFramerProvTable	1.3.6.1.4.1.562.2.4.1.101.2.10		not-accessible	This group contains the base provisioning data for the Framer component. Application or hardware interface specific provisioning data is contained in other provisional Framer groups.
frDteFramerProvEntry	1.3.6.1.4.1.562.2.4.1.101.2.10.1		not-accessible	An entry in the frDteFramerProvTable.
LIN frDteFramerInterfaceName	1.3.6.1.4.1.562.2.4.1.101.2.10.1.1	Link	read-write	This attribute contains a hardware component name. The attribute associates the application with a specific link. This defines the module processor on which Framer's parent component (as well as Framer itself) will run.
frDteFramerStateTable	1.3.6.1.4.1.562.2.4.1.101.2.12		not-accessible	This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
frDteFramerStateEntry	1.3.6.1.4.1.562.2.4.1.101.2.12.1		not-accessible	An entry in the frDteFramerStateTable.
INT frDteFramerAdminState	1.3.6.1.4.1.562.2.4.1.101.2.12.1.1	INTEGER	read-only	This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
INT frDteFramerOperationalState	1.3.6.1.4.1.562.2.4.1.101.2.12.1.2	INTEGER	read-only	This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
INT frDteFramerUsageState	1.3.6.1.4.1.562.2.4.1.101.2.12.1.3	INTEGER	read-only	This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
frDteFramerStatsTable	1.3.6.1.4.1.562.2.4.1.101.2.13		not-accessible	This group contains the operational statistics data for a Framer component.
frDteFramerStatsEntry	1.3.6.1.4.1.562.2.4.1.101.2.13.1		not-accessible	An entry in the frDteFramerStatsTable.
C32 frDteFramerFrmToIf	1.3.6.1.4.1.562.2.4.1.101.2.13.1.1	Counter32	read-only	This attribute counts the number of frames transmitted to the link interface by Framer. Note: This does not include the number of frames transmitted directly to the hardware queue, thus bypassing the Framer component.
C32 frDteFramerFrmFromIf	1.3.6.1.4.1.562.2.4.1.101.2.13.1.2	Counter32	read-only	This attribute counts the number of frames received from the link interface by Framer.
C32 frDteFramerAborts	1.3.6.1.4.1.562.2.4.1.101.2.13.1.3	Counter32	read-only	This attribute counts the total number of aborts received.
C32 frDteFramerCrcErrors	1.3.6.1.4.1.562.2.4.1.101.2.13.1.4	Counter32	read-only	This attribute counts the total number of frames with CRC errors.
C32 frDteFramerLrcErrors	1.3.6.1.4.1.562.2.4.1.101.2.13.1.5	Counter32	read-only	This attribute counts the total number of frames with LRC errors.
C32 frDteFramerNonOctetErrors	1.3.6.1.4.1.562.2.4.1.101.2.13.1.6	Counter32	read-only	This attribute counts the total number of frames that were non octet aligned.
C32 frDteFramerOverruns	1.3.6.1.4.1.562.2.4.1.101.2.13.1.7	Counter32	read-only	This attribute counts the total number of frames received from the link for which overruns occurred.
C32 frDteFramerUnderruns	1.3.6.1.4.1.562.2.4.1.101.2.13.1.8	Counter32	read-only	This attribute counts the total number of frames transmitted to the link for which underruns occurred.
C32 frDteFramerLargeFrmErrors	1.3.6.1.4.1.562.2.4.1.101.2.13.1.9	Counter32	read-only	This attribute counts the total number of frames received which were too large. The frame exceeded the maximumFrameLengthLimit provisioned attribute or it contained more than the 255 block hardware limit.
frDteFramerUtilTable	1.3.6.1.4.1.562.2.4.1.101.2.14		not-accessible	This group contains the link utilization operational data for a Framer component.
frDteFramerUtilEntry	1.3.6.1.4.1.562.2.4.1.101.2.14.1		not-accessible	An entry in the frDteFramerUtilTable.
G32 frDteFramerNormPrioLinkUtilToIf	1.3.6.1.4.1.562.2.4.1.101.2.14.1.1	Gauge32	read-only	This attribute is the utilization of the normal priority data sent to the link as a percentage of the available bandwidth on the link. The utilization is the average for the last minute.
G32 frDteFramerNormPrioLinkUtilFromIf	1.3.6.1.4.1.562.2.4.1.101.2.14.1.3	Gauge32	read-only	This attribute is the utilization of the normal priority data received from the link as a percentage of the available bandwidth on the link. The utilization is the average for the last minute.
frDteLmi	1.3.6.1.4.1.562.2.4.1.101.3
frDteLmiRowStatusTable	1.3.6.1.4.1.562.2.4.1.101.3.1		not-accessible	This entry controls the addition and deletion of frDteLmi components.
frDteLmiRowStatusEntry	1.3.6.1.4.1.562.2.4.1.101.3.1.1		not-accessible	A single entry in the table represents a single frDteLmi component.
ROW frDteLmiRowStatus	1.3.6.1.4.1.562.2.4.1.101.3.1.1.1	RowStatus	read-only	This variable is used as the basis for SNMP naming of frDteLmi components. These components cannot be added nor deleted.
STR frDteLmiComponentName	1.3.6.1.4.1.562.2.4.1.101.3.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO frDteLmiStorageType	1.3.6.1.4.1.562.2.4.1.101.3.1.1.4	StorageType	read-only	This variable represents the storage type value for the frDteLmi tables.
NON frDteLmiIndex	1.3.6.1.4.1.562.2.4.1.101.3.1.1.10	NonReplicated	not-accessible	This variable represents the index for the frDteLmi tables.
frDteLmiProvTable	1.3.6.1.4.1.562.2.4.1.101.3.10		not-accessible	This group contains the provisioned attributes for the Lmi component.
frDteLmiProvEntry	1.3.6.1.4.1.562.2.4.1.101.3.10.1		not-accessible	An entry in the frDteLmiProvTable.
INT frDteLmiProcedures	1.3.6.1.4.1.562.2.4.1.101.3.10.1.1	INTEGER	read-write	This attribute selects the Local Management Interface (LMI) protocol to be used on the interface. This attribute is equivalent to the SNMP variable frDlcmiState. The vendorForum LMI protocol automatically implies that the DLCI used by the protocol is 1023. The ansi (T1.617 Annex D) and itu (ITU-T Recommendation Q.933 Annex A) LMI protocols use DLCI 0. If none is selected, no LMI procedures will run on the interface. Note that the ITU-T Recommendation Q.933 was previously a CCITT recommendation.
U32 frDteLmiPollingInterval	1.3.6.1.4.1.562.2.4.1.101.3.10.1.4	Unsigned32	read-write	This is the number of seconds between successive status enquiry messages. This field corresponds to the parameter T391 described in the ANSI T1.617-1991 Annex D.
U32 frDteLmiFullEnquiryInterval	1.3.6.1.4.1.562.2.4.1.101.3.10.1.5	Unsigned32	read-write	The count of status polls before a full status enquiry message is issued. Every nth poll will request a full status. This field corresponds to the parameter N391 described in the ANSI T1.617-1991 Annex D.
U32 frDteLmiErrorThreshold	1.3.6.1.4.1.562.2.4.1.101.3.10.1.6	Unsigned32	read-write	The number of errors detected within the monitored events window before declaring the link non-functional. This field corresponds to the parameter N392 described in the ANSI T1.617-1991 Annex D.
U32 frDteLmiMonitoredEvents	1.3.6.1.4.1.562.2.4.1.101.3.10.1.7	Unsigned32	read-write	The number of status polling intervals over which the errorthreshold is counted This is used to determine if the errorThreshold is exceeded. This field corresponds to the parameter N393 described in the ANSI T1.617-1991 Annex D.
frDteLmiOperTable	1.3.6.1.4.1.562.2.4.1.101.3.11		not-accessible	This group contains the operational attributes for the Lmi component.
frDteLmiOperEntry	1.3.6.1.4.1.562.2.4.1.101.3.11.1		not-accessible	An entry in the frDteLmiOperTable.
INT frDteLmiLmiStatus	1.3.6.1.4.1.562.2.4.1.101.3.11.1.2	INTEGER	read-only	This indicates the status of the Frame Relay interface as determined by the performance of the link management interface (LMI). If no LMI is running, lmiStatus will stay in the running state indefinitely.
frDteRg	1.3.6.1.4.1.562.2.4.1.101.4
frDteRgRowStatusTable	1.3.6.1.4.1.562.2.4.1.101.4.1		not-accessible	This entry controls the addition and deletion of frDteRg components.
frDteRgRowStatusEntry	1.3.6.1.4.1.562.2.4.1.101.4.1.1		not-accessible	A single entry in the table represents a single frDteRg component.
ROW frDteRgRowStatus	1.3.6.1.4.1.562.2.4.1.101.4.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of frDteRg components. These components can be added and deleted.
STR frDteRgComponentName	1.3.6.1.4.1.562.2.4.1.101.4.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO frDteRgStorageType	1.3.6.1.4.1.562.2.4.1.101.4.1.1.4	StorageType	read-only	This variable represents the storage type value for the frDteRg tables.
I32 frDteRgIndex	1.3.6.1.4.1.562.2.4.1.101.4.1.1.10	Integer32	not-accessible	This variable represents the index for the frDteRg tables.
frDteRgIfEntryTable	1.3.6.1.4.1.562.2.4.1.101.4.10		not-accessible	This group contains the provisionable attributes for the ifEntry.
frDteRgIfEntryEntry	1.3.6.1.4.1.562.2.4.1.101.4.10.1		not-accessible	An entry in the frDteRgIfEntryTable.
INT frDteRgIfAdminStatus	1.3.6.1.4.1.562.2.4.1.101.4.10.1.1	INTEGER	read-write	The desired state of the interface. The up state indicates the interface is operational. The down state indicates the interface is not operational. The testing state indicates that no operational packets can be passed.
NUM frDteRgIfIndex	1.3.6.1.4.1.562.2.4.1.101.4.10.1.2	InterfaceIndex	read-only	This is the index for the IfEntry. Its value is automatically initialized during the provisioning process.
frDteRgProvTable	1.3.6.1.4.1.562.2.4.1.101.4.11		not-accessible	This group contains the provisioned attributes for the Remote Group component.
frDteRgProvEntry	1.3.6.1.4.1.562.2.4.1.101.4.11.1		not-accessible	An entry in the frDteRgProvTable.
U32 frDteRgMaxTransmissionUnit	1.3.6.1.4.1.562.2.4.1.101.4.11.1.1	Unsigned32	read-write	The Maximum Transmission Unit size of the largest datagram (including Frame Relay header) which can be sent on the interface.
frDteRgMpTable	1.3.6.1.4.1.562.2.4.1.101.4.12		not-accessible	This group contains the base provisioning data for the Media Application component.
frDteRgMpEntry	1.3.6.1.4.1.562.2.4.1.101.4.12.1		not-accessible	An entry in the frDteRgMpTable.
LIN frDteRgLinkToProtocolPort	1.3.6.1.4.1.562.2.4.1.101.4.12.1.1	Link	read-write	This attribute contains a protocol port component name. The attribute associates the application with a protocol port.
frDteRgStateTable	1.3.6.1.4.1.562.2.4.1.101.4.13		not-accessible	This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
frDteRgStateEntry	1.3.6.1.4.1.562.2.4.1.101.4.13.1		not-accessible	An entry in the frDteRgStateTable.
INT frDteRgAdminState	1.3.6.1.4.1.562.2.4.1.101.4.13.1.1	INTEGER	read-only	This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
INT frDteRgOperationalState	1.3.6.1.4.1.562.2.4.1.101.4.13.1.2	INTEGER	read-only	This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
INT frDteRgUsageState	1.3.6.1.4.1.562.2.4.1.101.4.13.1.3	INTEGER	read-only	This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
frDteRgOperStatusTable	1.3.6.1.4.1.562.2.4.1.101.4.14		not-accessible	This group includes the Operational Status attribute. This attribute defines the current operational state of this component.
frDteRgOperStatusEntry	1.3.6.1.4.1.562.2.4.1.101.4.14.1		not-accessible	An entry in the frDteRgOperStatusTable.
INT frDteRgSnmpOperStatus	1.3.6.1.4.1.562.2.4.1.101.4.14.1.1	INTEGER	read-only	The current state of the interface. The up state indicates the interface is operational and capable of forwarding packets. The down state indicates the interface is not operational, thus unable to forward packets. testing state indicates that no operational packets can be passed.
frDteRgBfr	1.3.6.1.4.1.562.2.4.1.101.4.15
frDteRgBfrRowStatusTable	1.3.6.1.4.1.562.2.4.1.101.4.15.1		not-accessible	This entry controls the addition and deletion of frDteRgBfr components.
frDteRgBfrRowStatusEntry	1.3.6.1.4.1.562.2.4.1.101.4.15.1.1		not-accessible	A single entry in the table represents a single frDteRgBfr component.
ROW frDteRgBfrRowStatus	1.3.6.1.4.1.562.2.4.1.101.4.15.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of frDteRgBfr components. These components can be added and deleted.
STR frDteRgBfrComponentName	1.3.6.1.4.1.562.2.4.1.101.4.15.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO frDteRgBfrStorageType	1.3.6.1.4.1.562.2.4.1.101.4.15.1.1.4	StorageType	read-only	This variable represents the storage type value for the frDteRgBfr tables.
NON frDteRgBfrIndex	1.3.6.1.4.1.562.2.4.1.101.4.15.1.1.10	NonReplicated	not-accessible	This variable represents the index for the frDteRgBfr tables.
frDteRgBfrProvTable	1.3.6.1.4.1.562.2.4.1.101.4.15.10		not-accessible	This group contains the provisioning attributes for the Bfr component.
frDteRgBfrProvEntry	1.3.6.1.4.1.562.2.4.1.101.4.15.10.1		not-accessible	An entry in the frDteRgBfrProvTable.
INT frDteRgBfrMacType	1.3.6.1.4.1.562.2.4.1.101.4.15.10.1.1	INTEGER	read-write	This attribute specifies the MAC address type of the Bfr component. The value must be chosen based on the media of the traffic source. For traffic originated from FDDI, use fddi; for ethernet, use enet; for token ring, use tokenRing
INT frDteRgBfrBfrIndex	1.3.6.1.4.1.562.2.4.1.101.4.15.10.1.2	INTEGER	read-write	This attribute specifies the value which is used to derive a unique MAC address for the Bfr. The bfrIndex must be unique across all Bfrs on the same Lp.
frDteRgBfrOprTable	1.3.6.1.4.1.562.2.4.1.101.4.15.11		not-accessible	This group contains the operational attributes for the Bfr component..
frDteRgBfrOprEntry	1.3.6.1.4.1.562.2.4.1.101.4.15.11.1		not-accessible	An entry in the frDteRgBfrOprTable.
STR frDteRgBfrMacAddr	1.3.6.1.4.1.562.2.4.1.101.4.15.11.1.1	DashedHexString	read-only	This attribute indicates the unique MAC address of the Bfr component. This value is derived by the value of the attribute bfrIndex. The value is displayed as cannonical format.
frDteRgLtDlciTable	1.3.6.1.4.1.562.2.4.1.101.4.219		not-accessible	This attribute associates a Rg component with zero or more StDlci components. The Rg and StDlci components must be under the same FrDte component.
frDteRgLtDlciEntry	1.3.6.1.4.1.562.2.4.1.101.4.219.1		not-accessible	An entry in the frDteRgLtDlciTable.
LIN frDteRgLtDlciValue	1.3.6.1.4.1.562.2.4.1.101.4.219.1.1	Link	read-write	This variable represents both the value and the index for the frDteRgLtDlciTable.
ROW frDteRgLtDlciRowStatus	1.3.6.1.4.1.562.2.4.1.101.4.219.1.2	RowStatus	write-only	This variable is used to control the addition and deletion of individual values of the frDteRgLtDlciTable.
frDteDynDlciDefs	1.3.6.1.4.1.562.2.4.1.101.5
frDteDynDlciDefsRowStatusTable	1.3.6.1.4.1.562.2.4.1.101.5.1		not-accessible	This entry controls the addition and deletion of frDteDynDlciDefs components.
frDteDynDlciDefsRowStatusEntry	1.3.6.1.4.1.562.2.4.1.101.5.1.1		not-accessible	A single entry in the table represents a single frDteDynDlciDefs component.
ROW frDteDynDlciDefsRowStatus	1.3.6.1.4.1.562.2.4.1.101.5.1.1.1	RowStatus	read-only	This variable is used as the basis for SNMP naming of frDteDynDlciDefs components. These components cannot be added nor deleted.
STR frDteDynDlciDefsComponentName	1.3.6.1.4.1.562.2.4.1.101.5.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO frDteDynDlciDefsStorageType	1.3.6.1.4.1.562.2.4.1.101.5.1.1.4	StorageType	read-only	This variable represents the storage type value for the frDteDynDlciDefs tables.
NON frDteDynDlciDefsIndex	1.3.6.1.4.1.562.2.4.1.101.5.1.1.10	NonReplicated	not-accessible	This variable represents the index for the frDteDynDlciDefs tables.
frDteDynDlciDefsProvTable	1.3.6.1.4.1.562.2.4.1.101.5.10		not-accessible	This group contains the provisioned attributes for a virtual circuit. These attributes represent the default settings for the resulting Dlci components and can be operationally changed using the corresponding attributes under the Dlci component.
frDteDynDlciDefsProvEntry	1.3.6.1.4.1.562.2.4.1.101.5.10.1		not-accessible	An entry in the frDteDynDlciDefsProvTable.
INT frDteDynDlciDefsStdRowStatus	1.3.6.1.4.1.562.2.4.1.101.5.10.1.1	INTEGER	read-write	This attribute is used to manage the status of a StDlci component. Set to active to enable the StDlci component. Set to notInService to disable the StDlci component. Set to createAndGo (SNMP only) to create a new StDlci component. Set to destroy (SNMP only) to delete an existing StDlci component.
INT frDteDynDlciDefsRateEnforcement	1.3.6.1.4.1.562.2.4.1.101.5.10.1.2	INTEGER	read-write	This attribute specifies whether the CIR attributes committedInformationRate, committedBurst, and excessBurst are used to define rate enforcement on this user DLCI. If rateEnforcement is enabled, and the combined Committed and Excess burst thresholds are exceeded, the frame in violation will be discarded immediately if a HibernationQueue subcomponent is not provisioned under the StDlci component. If a HibernationQueue is provisioned, the frame will be placed on the HibernationQueue at time of violation and transmission will be attempted later after the point at which the burst thresholds will no longer be exceeded. Setting all the CIR attributes to zero has the same affect as setting this attribute to disabled.
U32 frDteDynDlciDefsCommittedInformationRate	1.3.6.1.4.1.562.2.4.1.101.5.10.1.3	Unsigned32	read-write	The average number of bits to be transferred per second over the DLCI to the DCE. When this attribute is set to zero, the link speed will be used instead.
U32 frDteDynDlciDefsCommittedBurst	1.3.6.1.4.1.562.2.4.1.101.5.10.1.4	Unsigned32	read-write	The committed burst size (in bits) to which the DLCI wants to subscribe.
U32 frDteDynDlciDefsExcessBurst	1.3.6.1.4.1.562.2.4.1.101.5.10.1.5	Unsigned32	read-write	The excess burst size (in bits) to which the DLCI wants to subscribe.
INT frDteDynDlciDefsExcessBurstAction	1.3.6.1.4.1.562.2.4.1.101.5.10.1.6	INTEGER	read-write	This attribute specifies the action taken when the committedBurst size has been exceeded on the DLCI but the excessBurst size has not. If the attribute is set to setDeBit, the Discard Eligibility bit in the Frame Relay header will be turned on. If the attribute is set to none, no action will be taken.
U32 frDteDynDlciDefsIpCos	1.3.6.1.4.1.562.2.4.1.101.5.10.1.7	Unsigned32	read-write	This attribute specifies the initial Class of Service (CoS) given to each packet received on the on the virtual circuit identified by the dlci. The CoS value n is used to select Vr/ QosP/n. which determines the QualityofService-Profile to be used when the packet is forwarded. The intial CoS given to a packet by the assignedQoS attribute may be overriden when the cosPolicyAssignment attribute is defined on the IpPort or Ip components. When a packet is to be transmitted on a frDte protocol port where multiple virtual circuits are available for the packet's next hop, the packet is forwarded using the dlci where the ipCos value matches the CoS of the packet. When the packets's CoS does not match the ipCos value of any of the available virtual circuits, the packet will be forwarded using next lowest CoS; failing this, the packet will be forwarded using the next highest CoS.
frDteStDlci	1.3.6.1.4.1.562.2.4.1.101.6
frDteStDlciRowStatusTable	1.3.6.1.4.1.562.2.4.1.101.6.1		not-accessible	This entry controls the addition and deletion of frDteStDlci components.
frDteStDlciRowStatusEntry	1.3.6.1.4.1.562.2.4.1.101.6.1.1		not-accessible	A single entry in the table represents a single frDteStDlci component.
ROW frDteStDlciRowStatus	1.3.6.1.4.1.562.2.4.1.101.6.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of frDteStDlci components. These components can be added and deleted.
STR frDteStDlciComponentName	1.3.6.1.4.1.562.2.4.1.101.6.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO frDteStDlciStorageType	1.3.6.1.4.1.562.2.4.1.101.6.1.1.4	StorageType	read-only	This variable represents the storage type value for the frDteStDlci tables.
I32 frDteStDlciIndex	1.3.6.1.4.1.562.2.4.1.101.6.1.1.10	Integer32	not-accessible	This variable represents the index for the frDteStDlci tables.
frDteStDlciHq	1.3.6.1.4.1.562.2.4.1.101.6.2
frDteStDlciHqRowStatusTable	1.3.6.1.4.1.562.2.4.1.101.6.2.1		not-accessible	This entry controls the addition and deletion of frDteStDlciHq components.
frDteStDlciHqRowStatusEntry	1.3.6.1.4.1.562.2.4.1.101.6.2.1.1		not-accessible	A single entry in the table represents a single frDteStDlciHq component.
ROW frDteStDlciHqRowStatus	1.3.6.1.4.1.562.2.4.1.101.6.2.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of frDteStDlciHq components. These components can be added and deleted.
STR frDteStDlciHqComponentName	1.3.6.1.4.1.562.2.4.1.101.6.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO frDteStDlciHqStorageType	1.3.6.1.4.1.562.2.4.1.101.6.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the frDteStDlciHq tables.
NON frDteStDlciHqIndex	1.3.6.1.4.1.562.2.4.1.101.6.2.1.1.10	NonReplicated	not-accessible	This variable represents the index for the frDteStDlciHq tables.
frDteStDlciHqProvTable	1.3.6.1.4.1.562.2.4.1.101.6.2.10		not-accessible	This group contains the Link Emission Queue provisioned attributes.
frDteStDlciHqProvEntry	1.3.6.1.4.1.562.2.4.1.101.6.2.10.1		not-accessible	An entry in the frDteStDlciHqProvTable.
U32 frDteStDlciHqMaxPackets	1.3.6.1.4.1.562.2.4.1.101.6.2.10.1.1	Unsigned32	read-write	This attribute specifies the maximum number of packets allowed in the Leq before being discarded. If this attribute is set to zero then the maximum number of packets is calculated from the transmit data rate. This calculated value is placed in queuePktThreshold.
U32 frDteStDlciHqMaxMsecData	1.3.6.1.4.1.562.2.4.1.101.6.2.10.1.2	Unsigned32	read-write	This attribute specifies the maximum number of 'Milliseconds worth of data' allowed in the Leq before packets are discarded. The queueByteThreshold will be calculated from this attribute, based on the transmit data rate.
U32 frDteStDlciHqMaxPercentMulticast	1.3.6.1.4.1.562.2.4.1.101.6.2.10.1.3	Unsigned32	read-write	This attribute specifies the maximum percentage of multicast packets allowed in the Leq, based on queuePktThreshold, before being discarded. The calculated value will be placed in queueMulticastThreshold.
U32 frDteStDlciHqTimeToLive	1.3.6.1.4.1.562.2.4.1.101.6.2.10.1.4	Unsigned32	read-write	This attribute specifies the 'Milliseconds Time To Live' of packets in the Leq. If the timeToLive of a packet expires, it will be discarded.
frDteStDlciHqStatsTable	1.3.6.1.4.1.562.2.4.1.101.6.2.11		not-accessible	This group contains HibernationQueue general statistics.
frDteStDlciHqStatsEntry	1.3.6.1.4.1.562.2.4.1.101.6.2.11.1		not-accessible	An entry in the frDteStDlciHqStatsTable.
C32 frDteStDlciHqTimedOutPkt	1.3.6.1.4.1.562.2.4.1.101.6.2.11.1.1	Counter32	read-only	This attribute counts the number of packets that have been discarded due to exceeding the timeToLive. This counter will wrap around to 0 when it exceeds its maximum count.
C32 frDteStDlciHqQueuePurgeDiscards	1.3.6.1.4.1.562.2.4.1.101.6.2.11.1.2	Counter32	read-only	This attribute counts the total number of packets discarded by a queue purge which occurs when the Dlci goes down. This counter will wrap around to 0 when it exceeds its maximum count.
frDteStDlciHqTStatsTable	1.3.6.1.4.1.562.2.4.1.101.6.2.12		not-accessible	This group contains Link Emission Queue total statistics.
frDteStDlciHqTStatsEntry	1.3.6.1.4.1.562.2.4.1.101.6.2.12.1		not-accessible	An entry in the frDteStDlciHqTStatsTable.
C32 frDteStDlciHqTotalPktHandled	1.3.6.1.4.1.562.2.4.1.101.6.2.12.1.1	Counter32	read-only	This attribute counts the total number of packets handled by the Leq. This counter will wrap around to 0 when it exceeds its maximum count.
C32 frDteStDlciHqTotalPktForwarded	1.3.6.1.4.1.562.2.4.1.101.6.2.12.1.2	Counter32	read-only	This attribute counts the total number of packets forwarded by the Leq. This counter will wrap around to 0 when it exceeds its maximum count.
C32 frDteStDlciHqTotalPktQueued	1.3.6.1.4.1.562.2.4.1.101.6.2.12.1.3	Counter32	read-only	This attribute counts the total number of packets that required queuing by the Leq due to transmit congestion. This counter will wrap around to 0 when it exceeds its maximum count.
C32 frDteStDlciHqTotalMulticastPkt	1.3.6.1.4.1.562.2.4.1.101.6.2.12.1.4	Counter32	read-only	This attribute counts the total number of multicast packets handled by this instance of FrDte. This counter will wrap around to 0 when it exceeds its maximum count.
C32 frDteStDlciHqTotalPktDiscards	1.3.6.1.4.1.562.2.4.1.101.6.2.12.1.5	Counter32	read-only	This attribute counts the total number of packets that were discarded for this instance of FrDte. This is the sum of timedOutPkt, forcedPktDiscards, queuePurgeDiscards, pktThresholdExceeded, byteThresholdExceeded, mulThresholdExceeded and memThresholdExceeded. This counter will wrap around to 0 when it exceeds its maximum count.
frDteStDlciHqCStatsTable	1.3.6.1.4.1.562.2.4.1.101.6.2.13		not-accessible	This group contains Link Emission Queue current statistics.
frDteStDlciHqCStatsEntry	1.3.6.1.4.1.562.2.4.1.101.6.2.13.1		not-accessible	An entry in the frDteStDlciHqCStatsTable.
G32 frDteStDlciHqCurrentPktQueued	1.3.6.1.4.1.562.2.4.1.101.6.2.13.1.1	Gauge32	read-only	This attribute contains the current number of packets queued.
G32 frDteStDlciHqCurrentBytesQueued	1.3.6.1.4.1.562.2.4.1.101.6.2.13.1.2	Gauge32	read-only	This attribute contains the current number of bytes queued.
G32 frDteStDlciHqCurrentMulticastQueued	1.3.6.1.4.1.562.2.4.1.101.6.2.13.1.3	Gauge32	read-only	This attribute counts the current number of multicast packets in the queue.
frDteStDlciHqThrStatsTable	1.3.6.1.4.1.562.2.4.1.101.6.2.14		not-accessible	This group contains Link Emission Queue threshold statistics.
frDteStDlciHqThrStatsEntry	1.3.6.1.4.1.562.2.4.1.101.6.2.14.1		not-accessible	An entry in the frDteStDlciHqThrStatsTable.
U32 frDteStDlciHqQueuePktThreshold	1.3.6.1.4.1.562.2.4.1.101.6.2.14.1.1	Unsigned32	read-only	This attribute is the maximum number of packets that can be contained in the queue before being discarded. If maxPackets was set to 0 then this attribute will contain the value that has been calculated based on the transmit data rate. If maxPackets was set to one or more than this attribute will contain that number.
C32 frDteStDlciHqPktThresholdExceeded	1.3.6.1.4.1.562.2.4.1.101.6.2.14.1.2	Counter32	read-only	This attribute counts the number of packets discarded due to the queuePktThreshold being exceeded. This counter will wrap around to 0 when it exceeds its maximum count.
U32 frDteStDlciHqQueueByteThreshold	1.3.6.1.4.1.562.2.4.1.101.6.2.14.1.3	Unsigned32	read-only	This attribute is the maximum number of bytes allowed in the queue based on maxMsecData and the transmit data rate.
C32 frDteStDlciHqByteThresholdExceeded	1.3.6.1.4.1.562.2.4.1.101.6.2.14.1.4	Counter32	read-only	This attribute counts the number of packets discarded due to the queueByteThreshold being exceeded. This counter will wrap around to 0 when it exceeds its maximum count.
U32 frDteStDlciHqQueueMulticastThreshold	1.3.6.1.4.1.562.2.4.1.101.6.2.14.1.5	Unsigned32	read-only	This attribute is the number of multicast packets allowed in the queue based on maxPercentMulticast and maxPackets.
C32 frDteStDlciHqMulThresholdExceeded	1.3.6.1.4.1.562.2.4.1.101.6.2.14.1.6	Counter32	read-only	This attribute counts the number of packets discarded due to the queueMulticastThreshold being exceeded. This counter will wrap around to 0 when it exceeds its maximum count.
C32 frDteStDlciHqMemThresholdExceeded	1.3.6.1.4.1.562.2.4.1.101.6.2.14.1.7	Counter32	read-only	This attribute counts the number of packets discarded due to exceeding the memory usage threshold for Leq. The memory usage threshold is determined by the Leq software, guaranteeing that the Leq does not consume all of the memory. This counter will wrap around to 0 when it exceeds its maximum count.
frDteStDlciProvTable	1.3.6.1.4.1.562.2.4.1.101.6.10		not-accessible	This group contains the provisioned attributes for a virtual circuit. These attributes represent the default settings for the resulting Dlci components and can be operationally changed using the corresponding attributes under the Dlci component.
frDteStDlciProvEntry	1.3.6.1.4.1.562.2.4.1.101.6.10.1		not-accessible	An entry in the frDteStDlciProvTable.
INT frDteStDlciStdRowStatus	1.3.6.1.4.1.562.2.4.1.101.6.10.1.1	INTEGER	read-write	This attribute is used to manage the status of a StDlci component. Set to active to enable the StDlci component. Set to notInService to disable the StDlci component. Set to createAndGo (SNMP only) to create a new StDlci component. Set to destroy (SNMP only) to delete an existing StDlci component.
INT frDteStDlciRateEnforcement	1.3.6.1.4.1.562.2.4.1.101.6.10.1.2	INTEGER	read-write	This attribute specifies whether the CIR attributes committedInformationRate, committedBurst, and excessBurst are used to define rate enforcement on this user DLCI. If rateEnforcement is enabled, and the combined Committed and Excess burst thresholds are exceeded, the frame in violation will be discarded immediately if a HibernationQueue subcomponent is not provisioned under the StDlci component. If a HibernationQueue is provisioned, the frame will be placed on the HibernationQueue at time of violation and transmission will be attempted later after the point at which the burst thresholds will no longer be exceeded. Setting all the CIR attributes to zero has the same affect as setting this attribute to disabled.
U32 frDteStDlciCommittedInformationRate	1.3.6.1.4.1.562.2.4.1.101.6.10.1.3	Unsigned32	read-write	The average number of bits to be transferred per second over the DLCI to the DCE. When this attribute is set to zero, the link speed will be used instead.
U32 frDteStDlciCommittedBurst	1.3.6.1.4.1.562.2.4.1.101.6.10.1.4	Unsigned32	read-write	The committed burst size (in bits) to which the DLCI wants to subscribe.
U32 frDteStDlciExcessBurst	1.3.6.1.4.1.562.2.4.1.101.6.10.1.5	Unsigned32	read-write	The excess burst size (in bits) to which the DLCI wants to subscribe.
INT frDteStDlciExcessBurstAction	1.3.6.1.4.1.562.2.4.1.101.6.10.1.6	INTEGER	read-write	This attribute specifies the action taken when the committedBurst size has been exceeded on the DLCI but the excessBurst size has not. If the attribute is set to setDeBit, the Discard Eligibility bit in the Frame Relay header will be turned on. If the attribute is set to none, no action will be taken.
U32 frDteStDlciIpCos	1.3.6.1.4.1.562.2.4.1.101.6.10.1.7	Unsigned32	read-write	This attribute specifies the initial Class of Service (CoS) given to each packet received on the on the virtual circuit identified by the dlci. The CoS value n is used to select Vr/ QosP/n. which determines the QualityofService-Profile to be used when the packet is forwarded. The intial CoS given to a packet by the assignedQoS attribute may be overriden when the cosPolicyAssignment attribute is defined on the IpPort or Ip components. When a packet is to be transmitted on a frDte protocol port where multiple virtual circuits are available for the packet's next hop, the packet is forwarded using the dlci where the ipCos value matches the CoS of the packet. When the packets's CoS does not match the ipCos value of any of the available virtual circuits, the packet will be forwarded using next lowest CoS; failing this, the packet will be forwarded using the next highest CoS.
frDteStDlciRgLinkTable	1.3.6.1.4.1.562.2.4.1.101.6.11		not-accessible	This group provides the link between a Dlci and a remoteGroup.
frDteStDlciRgLinkEntry	1.3.6.1.4.1.562.2.4.1.101.6.11.1		not-accessible	An entry in the frDteStDlciRgLinkTable.
LIN frDteStDlciLinkToRemoteGroup	1.3.6.1.4.1.562.2.4.1.101.6.11.1.1	Link	read-write	This attribute associates a StDlci component with a Rg component. Provisioned StDlci components must be linked to a Rg component which is under the same FrDte component.
frDteLeq	1.3.6.1.4.1.562.2.4.1.101.7
frDteLeqRowStatusTable	1.3.6.1.4.1.562.2.4.1.101.7.1		not-accessible	This entry controls the addition and deletion of frDteLeq components.
frDteLeqRowStatusEntry	1.3.6.1.4.1.562.2.4.1.101.7.1.1		not-accessible	A single entry in the table represents a single frDteLeq component.
ROW frDteLeqRowStatus	1.3.6.1.4.1.562.2.4.1.101.7.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of frDteLeq components. These components can be added and deleted.
STR frDteLeqComponentName	1.3.6.1.4.1.562.2.4.1.101.7.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO frDteLeqStorageType	1.3.6.1.4.1.562.2.4.1.101.7.1.1.4	StorageType	read-only	This variable represents the storage type value for the frDteLeq tables.
NON frDteLeqIndex	1.3.6.1.4.1.562.2.4.1.101.7.1.1.10	NonReplicated	not-accessible	This variable represents the index for the frDteLeq tables.
frDteLeqProvTable	1.3.6.1.4.1.562.2.4.1.101.7.10		not-accessible	This group contains the Link Emission Queue provisioned attributes.
frDteLeqProvEntry	1.3.6.1.4.1.562.2.4.1.101.7.10.1		not-accessible	An entry in the frDteLeqProvTable.
U32 frDteLeqMaxPackets	1.3.6.1.4.1.562.2.4.1.101.7.10.1.1	Unsigned32	read-write	This attribute specifies the maximum number of packets allowed in the Leq before being discarded. If this attribute is set to zero then the maximum number of packets is calculated from the transmit data rate. This calculated value is placed in queuePktThreshold.
U32 frDteLeqMaxMsecData	1.3.6.1.4.1.562.2.4.1.101.7.10.1.2	Unsigned32	read-write	This attribute specifies the maximum number of 'Milliseconds worth of data' allowed in the Leq before packets are discarded. The queueByteThreshold will be calculated from this attribute, based on the transmit data rate.
U32 frDteLeqMaxPercentMulticast	1.3.6.1.4.1.562.2.4.1.101.7.10.1.3	Unsigned32	read-write	This attribute specifies the maximum percentage of multicast packets allowed in the Leq, based on queuePktThreshold, before being discarded. The calculated value will be placed in queueMulticastThreshold.
U32 frDteLeqTimeToLive	1.3.6.1.4.1.562.2.4.1.101.7.10.1.4	Unsigned32	read-write	This attribute specifies the 'Milliseconds Time To Live' of packets in the Leq. If the timeToLive of a packet expires, it will be discarded.
frDteLeqStatsTable	1.3.6.1.4.1.562.2.4.1.101.7.11		not-accessible	This group contains Link Emission Queue general statistics.
frDteLeqStatsEntry	1.3.6.1.4.1.562.2.4.1.101.7.11.1		not-accessible	An entry in the frDteLeqStatsTable.
C32 frDteLeqTimedOutPkt	1.3.6.1.4.1.562.2.4.1.101.7.11.1.1	Counter32	read-only	This attribute counts the number of packets that have been discarded due to exceeding the timeToLive. This counter will wrap around to 0 when it exceeds its maximum count.
C32 frDteLeqHardwareForcedPkt	1.3.6.1.4.1.562.2.4.1.101.7.11.1.2	Counter32	read-only	This attribute counts the number of hardware forced packets on this instance of FrDte. This counter will wrap around to 0 when it exceeds its maximum count.
C32 frDteLeqForcedPktDiscards	1.3.6.1.4.1.562.2.4.1.101.7.11.1.3	Counter32	read-only	This attribute counts the total number of hardware forced packets that had to be discarded due to link failure. This counter will wrap around to 0 when it exceeds its maximum count.
C32 frDteLeqQueuePurgeDiscards	1.3.6.1.4.1.562.2.4.1.101.7.11.1.4	Counter32	read-only	This attribute counts the total number of packets discarded by a queue purge (i.e. a discarding of all packets on the queue). This counter will wrap around to 0 when it exceeds its maximum count.
frDteLeqTStatsTable	1.3.6.1.4.1.562.2.4.1.101.7.12		not-accessible	This group contains Link Emission Queue total statistics.
frDteLeqTStatsEntry	1.3.6.1.4.1.562.2.4.1.101.7.12.1		not-accessible	An entry in the frDteLeqTStatsTable.
C32 frDteLeqTotalPktHandled	1.3.6.1.4.1.562.2.4.1.101.7.12.1.1	Counter32	read-only	This attribute counts the total number of packets handled by the Leq. This counter will wrap around to 0 when it exceeds its maximum count.
C32 frDteLeqTotalPktForwarded	1.3.6.1.4.1.562.2.4.1.101.7.12.1.2	Counter32	read-only	This attribute counts the total number of packets forwarded by the Leq. This counter will wrap around to 0 when it exceeds its maximum count.
C32 frDteLeqTotalPktQueued	1.3.6.1.4.1.562.2.4.1.101.7.12.1.3	Counter32	read-only	This attribute counts the total number of packets that required queuing by the Leq due to transmit congestion. This counter will wrap around to 0 when it exceeds its maximum count.
C32 frDteLeqTotalMulticastPkt	1.3.6.1.4.1.562.2.4.1.101.7.12.1.4	Counter32	read-only	This attribute counts the total number of multicast packets handled by this instance of FrDte. This counter will wrap around to 0 when it exceeds its maximum count.
C32 frDteLeqTotalPktDiscards	1.3.6.1.4.1.562.2.4.1.101.7.12.1.5	Counter32	read-only	This attribute counts the total number of packets that were discarded for this instance of FrDte. This is the sum of timedOutPkt, forcedPktDiscards, queuePurgeDiscards, pktThresholdExceeded, byteThresholdExceeded, mulThresholdExceeded and memThresholdExceeded. This counter will wrap around to 0 when it exceeds its maximum count.
frDteLeqCStatsTable	1.3.6.1.4.1.562.2.4.1.101.7.13		not-accessible	This group contains Link Emission Queue current statistics.
frDteLeqCStatsEntry	1.3.6.1.4.1.562.2.4.1.101.7.13.1		not-accessible	An entry in the frDteLeqCStatsTable.
G32 frDteLeqCurrentPktQueued	1.3.6.1.4.1.562.2.4.1.101.7.13.1.1	Gauge32	read-only	This attribute contains the current number of packets queued.
G32 frDteLeqCurrentBytesQueued	1.3.6.1.4.1.562.2.4.1.101.7.13.1.2	Gauge32	read-only	This attribute contains the current number of bytes queued.
G32 frDteLeqCurrentMulticastQueued	1.3.6.1.4.1.562.2.4.1.101.7.13.1.3	Gauge32	read-only	This attribute counts the current number of multicast packets in the queue.
frDteLeqThrStatsTable	1.3.6.1.4.1.562.2.4.1.101.7.14		not-accessible	This group contains Link Emission Queue threshold statistics.
frDteLeqThrStatsEntry	1.3.6.1.4.1.562.2.4.1.101.7.14.1		not-accessible	An entry in the frDteLeqThrStatsTable.
U32 frDteLeqQueuePktThreshold	1.3.6.1.4.1.562.2.4.1.101.7.14.1.1	Unsigned32	read-only	This attribute is the maximum number of packets that can be contained in the queue before being discarded. If maxPackets was set to 0 then this attribute will contain the value that has been calculated based on the transmit data rate. If maxPackets was set to one or more than this attribute will contain that number.
C32 frDteLeqPktThresholdExceeded	1.3.6.1.4.1.562.2.4.1.101.7.14.1.2	Counter32	read-only	This attribute counts the number of packets discarded due to the queuePktThreshold being exceeded. This counter will wrap around to 0 when it exceeds its maximum count.
U32 frDteLeqQueueByteThreshold	1.3.6.1.4.1.562.2.4.1.101.7.14.1.3	Unsigned32	read-only	This attribute is the maximum number of bytes allowed in the queue based on maxMsecData and the transmit data rate.
C32 frDteLeqByteThresholdExceeded	1.3.6.1.4.1.562.2.4.1.101.7.14.1.4	Counter32	read-only	This attribute counts the number of packets discarded due to the queueByteThreshold being exceeded. This counter will wrap around to 0 when it exceeds its maximum count.
U32 frDteLeqQueueMulticastThreshold	1.3.6.1.4.1.562.2.4.1.101.7.14.1.5	Unsigned32	read-only	This attribute is the number of multicast packets allowed in the queue based on maxPercentMulticast and maxPackets.
C32 frDteLeqMulThresholdExceeded	1.3.6.1.4.1.562.2.4.1.101.7.14.1.6	Counter32	read-only	This attribute counts the number of packets discarded due to the queueMulticastThreshold being exceeded. This counter will wrap around to 0 when it exceeds its maximum count.
C32 frDteLeqMemThresholdExceeded	1.3.6.1.4.1.562.2.4.1.101.7.14.1.7	Counter32	read-only	This attribute counts the number of packets discarded due to exceeding the memory usage threshold for Leq. The memory usage threshold is determined by the Leq software, guaranteeing that the Leq does not consume all of the memory. This counter will wrap around to 0 when it exceeds its maximum count.
frDteDlci	1.3.6.1.4.1.562.2.4.1.101.8
frDteDlciRowStatusTable	1.3.6.1.4.1.562.2.4.1.101.8.1		not-accessible	* THIS TABLE CURRENTLY NOT IMPLEMENTED * This entry controls the addition and deletion of frDteDlci components.
frDteDlciRowStatusEntry	1.3.6.1.4.1.562.2.4.1.101.8.1.1		not-accessible	A single entry in the table represents a single frDteDlci component.
ROW frDteDlciRowStatus	1.3.6.1.4.1.562.2.4.1.101.8.1.1.1	RowStatus	read-only	This variable is used as the basis for SNMP naming of frDteDlci components. These components cannot be added nor deleted.
STR frDteDlciComponentName	1.3.6.1.4.1.562.2.4.1.101.8.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO frDteDlciStorageType	1.3.6.1.4.1.562.2.4.1.101.8.1.1.4	StorageType	read-only	This variable represents the storage type value for the frDteDlci tables.
I32 frDteDlciIndex	1.3.6.1.4.1.562.2.4.1.101.8.1.1.10	Integer32	not-accessible	This variable represents the index for the frDteDlci tables.
frDteDlciStateTable	1.3.6.1.4.1.562.2.4.1.101.8.10		not-accessible	* THIS TABLE CURRENTLY NOT IMPLEMENTED * This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
frDteDlciStateEntry	1.3.6.1.4.1.562.2.4.1.101.8.10.1		not-accessible	An entry in the frDteDlciStateTable.
INT frDteDlciAdminState	1.3.6.1.4.1.562.2.4.1.101.8.10.1.1	INTEGER	read-only	This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
INT frDteDlciOperationalState	1.3.6.1.4.1.562.2.4.1.101.8.10.1.2	INTEGER	read-only	This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
INT frDteDlciUsageState	1.3.6.1.4.1.562.2.4.1.101.8.10.1.3	INTEGER	read-only	This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
frDteDlciOperTable	1.3.6.1.4.1.562.2.4.1.101.8.11		not-accessible	* THIS TABLE CURRENTLY NOT IMPLEMENTED * This group contains the operational attributes for the Dlci component.
frDteDlciOperEntry	1.3.6.1.4.1.562.2.4.1.101.8.11.1		not-accessible	An entry in the frDteDlciOperTable.
INT frDteDlciDlciState	1.3.6.1.4.1.562.2.4.1.101.8.11.1.4	INTEGER	read-only	This attribute reflects the current operational circuit state of the Dlci. The state active indicates that the circuit is up and inactive that the circuit is down. The state invalid means the circuit has been deleted by the DCE (via Lmi).
ENT frDteDlciLastTimeChange	1.3.6.1.4.1.562.2.4.1.101.8.11.1.5	EnterpriseDateAndTime	read-only	The last time dlciState changed state.
C32 frDteDlciSentFrames	1.3.6.1.4.1.562.2.4.1.101.8.11.1.7	Counter32	read-only	Number of frames transmitted across the interface. This counter will wrap around to 0 when it exceeds its maximum count.
C32 frDteDlciSentOctets	1.3.6.1.4.1.562.2.4.1.101.8.11.1.8	Counter32	read-only	The number of octets sent from this virtual circuit since it was created. This counter will wrap around to 0 when it exceeds its maximum count.
C32 frDteDlciReceivedFrames	1.3.6.1.4.1.562.2.4.1.101.8.11.1.9	Counter32	read-only	Number of frames received across the interface. This counter will wrap around to 0 when it exceeds its maximum count.
C32 frDteDlciReceivedOctets	1.3.6.1.4.1.562.2.4.1.101.8.11.1.10	Counter32	read-only	The number of octets sent from this virtual circuit since it was created. This counter will wrap around to 0 when it exceeds its maximum count.
C32 frDteDlciReceivedFECNs	1.3.6.1.4.1.562.2.4.1.101.8.11.1.11	Counter32	read-only	Number of frames with the FECN bit set received from the network. This counter will wrap around to 0 when it exceeds its maximum count.
C32 frDteDlciReceivedBECNs	1.3.6.1.4.1.562.2.4.1.101.8.11.1.12	Counter32	read-only	Number of frames with the BECN bit set received from the network. This counter will wrap around to 0 when it exceeds its maximum count.
C32 frDteDlciDiscardedFrames	1.3.6.1.4.1.562.2.4.1.101.8.11.1.13	Counter32	read-only	The number of inbound frames dropped because of format errors, or because the VC was inactive. This counter will wrap around to 0 when it exceeds its maximum count.
INT frDteDlciCreationType	1.3.6.1.4.1.562.2.4.1.101.8.11.1.14	INTEGER	read-only	This indicates whether the virtual circuit was manually created (static), or dynamically created (dynamic) via the data link control management interface.
ENT frDteDlciCreationTime	1.3.6.1.4.1.562.2.4.1.101.8.11.1.15	EnterpriseDateAndTime	read-only	The time when the circuit was created, whether by the Data Link Connection Management Interface or by an SNMP set request.
INT frDteDlciRateEnforcement	1.3.6.1.4.1.562.2.4.1.101.8.11.1.17	INTEGER	read-write	This attribute specifies whether the CIR attributes committedInformationRate, committedBurst, and excessBurst are used to define rate enforcement on this user DLCI. If rateEnforcement is enabled, and the combined Committed and Excess burst thresholds are exceeded, the frame in violation will be discarded immediately if a HibernationQueue subcomponent is not provisioned under the StDlci component (static entries only). If a HibernationQueue is provisioned, the frame will be placed on the HibernationQueue at time of violation and transmission will be attempted later after the point at which the burst thresholds will no longer be exceeded. Setting all the CIR attributes to zero has the same affect as setting this attribute to disabled. Setting this attribute will operationally override the corresponding provisional value on static entries.
G32 frDteDlciCommittedInformationRate	1.3.6.1.4.1.562.2.4.1.101.8.11.1.18	Gauge32	read-write	The average number of bits to be transferred per second over the DLCI to the DCE. When this attribute is set to zero, the link speed will be used instead. Setting this attribute will operationally override the corresponding provisional value on static entries.
U32 frDteDlciCommittedBurst	1.3.6.1.4.1.562.2.4.1.101.8.11.1.19	Unsigned32	read-write	The committed burst size (in bits) to which the DLCI wants to subscribe. Setting this attribute will operationally override the corresponding provisional value on static entries.
U32 frDteDlciExcessBurst	1.3.6.1.4.1.562.2.4.1.101.8.11.1.20	Unsigned32	read-write	The excess burst size (in bits) to which the DLCI wants to subscribe. Setting this attribute will operationally override the corresponding provisional value on static entries.
INT frDteDlciExcessBurstAction	1.3.6.1.4.1.562.2.4.1.101.8.11.1.21	INTEGER	read-write	This attribute specifies the action taken when the committedBurst size has been exceeded on the Dlci but the excessBurst size has not. If the attribute is set to setDeBit, the Discard Eligibility bit in the Frame Relay header will be turned on. If the attribute is set to none, no action will be taken. Setting this attribute will operationally override the corresponding provisional value on static entries.
frDteVFramer	1.3.6.1.4.1.562.2.4.1.101.9
frDteVFramerRowStatusTable	1.3.6.1.4.1.562.2.4.1.101.9.1		not-accessible	This entry controls the addition and deletion of frDteVFramer components.
frDteVFramerRowStatusEntry	1.3.6.1.4.1.562.2.4.1.101.9.1.1		not-accessible	A single entry in the table represents a single frDteVFramer component.
ROW frDteVFramerRowStatus	1.3.6.1.4.1.562.2.4.1.101.9.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of frDteVFramer components. These components can be added and deleted.
STR frDteVFramerComponentName	1.3.6.1.4.1.562.2.4.1.101.9.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO frDteVFramerStorageType	1.3.6.1.4.1.562.2.4.1.101.9.1.1.4	StorageType	read-only	This variable represents the storage type value for the frDteVFramer tables.
NON frDteVFramerIndex	1.3.6.1.4.1.562.2.4.1.101.9.1.1.10	NonReplicated	not-accessible	This variable represents the index for the frDteVFramer tables.
frDteVFramerProvTable	1.3.6.1.4.1.562.2.4.1.101.9.10		not-accessible	This group contains provisionable attributes for the VirtualFramer component.
frDteVFramerProvEntry	1.3.6.1.4.1.562.2.4.1.101.9.10.1		not-accessible	An entry in the frDteVFramerProvTable.
LIN frDteVFramerOtherVirtualFramer	1.3.6.1.4.1.562.2.4.1.101.9.10.1.1	Link	read-write	This attribute specifies the other VirtualFramer to which the service is linked, for example, FrUni/n VirtualFramer, FrDte/n VirtualFramer.
LIN frDteVFramerLogicalProcessor	1.3.6.1.4.1.562.2.4.1.101.9.10.1.2	Link	read-write	This attribute specifies the logical processor on which the service component will reside.
frDteVFramerStateTable	1.3.6.1.4.1.562.2.4.1.101.9.11		not-accessible	This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
frDteVFramerStateEntry	1.3.6.1.4.1.562.2.4.1.101.9.11.1		not-accessible	An entry in the frDteVFramerStateTable.
INT frDteVFramerAdminState	1.3.6.1.4.1.562.2.4.1.101.9.11.1.1	INTEGER	read-only	This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
INT frDteVFramerOperationalState	1.3.6.1.4.1.562.2.4.1.101.9.11.1.2	INTEGER	read-only	This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
INT frDteVFramerUsageState	1.3.6.1.4.1.562.2.4.1.101.9.11.1.3	INTEGER	read-only	This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
frDteVFramerStatsTable	1.3.6.1.4.1.562.2.4.1.101.9.12		not-accessible	This group contains the operational statistics data for a VirtualFramer component.
frDteVFramerStatsEntry	1.3.6.1.4.1.562.2.4.1.101.9.12.1		not-accessible	An entry in the frDteVFramerStatsTable.
NUM frDteVFramerFrmToOtherVFramer	1.3.6.1.4.1.562.2.4.1.101.9.12.1.2	PassportCounter64	read-only	This attribute counts the frames transmitted to the otherVirtualFramer.
NUM frDteVFramerFrmFromOtherVFramer	1.3.6.1.4.1.562.2.4.1.101.9.12.1.3	PassportCounter64	read-only	This attribute counts the frames received from the otherVirtualFramer.
NUM frDteVFramerOctetFromOtherVFramer	1.3.6.1.4.1.562.2.4.1.101.9.12.1.5	PassportCounter64	read-only	This attribute counts the octets received from the otherVirtualFramer.
frDteCidDataTable	1.3.6.1.4.1.562.2.4.1.101.20		not-accessible	This group contains the attribute for a component's Customer Identifier (CID). Refer to the attribute description for a detailed explanation of CIDs.
frDteCidDataEntry	1.3.6.1.4.1.562.2.4.1.101.20.1		not-accessible	An entry in the frDteCidDataTable.
U32 frDteCustomerIdentifier	1.3.6.1.4.1.562.2.4.1.101.20.1.1	Unsigned32	read-write	This attribute holds the Customer Identifier (CID). Every component has a CID. If a component has a cid attribute, the component's CID is the provisioned value of that attribute; otherwise the component inherits the CID of its parent. The top- level component has a CID of 0. Every operator session also has a CID, which is the CID provisioned for the operator's user ID. An operator will see only the stream data for components having a matching CID. Also, the operator will be allowed to issue commands for only those components which have a matching CID. An operator CID of 0 is used to identify the Network Manager (referred to as 'NetMan' in DPN). This CID matches the CID of any component. Values 1 to 8191 inclusive (equivalent to 'basic CIDs' in DPN) may be assigned to specific customers.
frDteIfEntryTable	1.3.6.1.4.1.562.2.4.1.101.21		not-accessible	This group contains the provisionable attributes for the ifEntry.
frDteIfEntryEntry	1.3.6.1.4.1.562.2.4.1.101.21.1		not-accessible	An entry in the frDteIfEntryTable.
INT frDteIfAdminStatus	1.3.6.1.4.1.562.2.4.1.101.21.1.1	INTEGER	read-write	The desired state of the interface. The up state indicates the interface is operational. The down state indicates the interface is not operational. The testing state indicates that no operational packets can be passed.
NUM frDteIfIndex	1.3.6.1.4.1.562.2.4.1.101.21.1.2	InterfaceIndex	read-only	This is the index for the IfEntry. Its value is automatically initialized during the provisioning process.
frDteProvTable	1.3.6.1.4.1.562.2.4.1.101.22		not-accessible	This group contains the provisioned attributes for the FrDte component.
frDteProvEntry	1.3.6.1.4.1.562.2.4.1.101.22.1		not-accessible	An entry in the frDteProvTable.
INT frDteAcceptUndefinedDlci	1.3.6.1.4.1.562.2.4.1.101.22.1.1	INTEGER	read-write	This parameter allows previously undefined Data Link Connection Identifiers (DLCIs) to be dynamically accepted in the default remote group. If set to enabled, undefined DLCIs will be accepted, if disabled, they will not.
frDteStateTable	1.3.6.1.4.1.562.2.4.1.101.23		not-accessible	This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
frDteStateEntry	1.3.6.1.4.1.562.2.4.1.101.23.1		not-accessible	An entry in the frDteStateTable.
INT frDteAdminState	1.3.6.1.4.1.562.2.4.1.101.23.1.1	INTEGER	read-only	This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
INT frDteOperationalState	1.3.6.1.4.1.562.2.4.1.101.23.1.2	INTEGER	read-only	This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
INT frDteUsageState	1.3.6.1.4.1.562.2.4.1.101.23.1.3	INTEGER	read-only	This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
frDteOperStatusTable	1.3.6.1.4.1.562.2.4.1.101.24		not-accessible	This group includes the Operational Status attribute. This attribute defines the current operational state of this component.
frDteOperStatusEntry	1.3.6.1.4.1.562.2.4.1.101.24.1		not-accessible	An entry in the frDteOperStatusTable.
INT frDteSnmpOperStatus	1.3.6.1.4.1.562.2.4.1.101.24.1.1	INTEGER	read-only	The current state of the interface. The up state indicates the interface is operational and capable of forwarding packets. The down state indicates the interface is not operational, thus unable to forward packets. testing state indicates that no operational packets can be passed.
frDteOperTable	1.3.6.1.4.1.562.2.4.1.101.25		not-accessible	This group contains the operational attributes for the FrDte component.
frDteOperEntry	1.3.6.1.4.1.562.2.4.1.101.25.1		not-accessible	An entry in the frDteOperTable.
INT frDteLinkOperState	1.3.6.1.4.1.562.2.4.1.101.25.1.1	INTEGER	read-only	This attribute describes the operational state of the Link Control protocol. If the interface to the physical link hardware is inactive, the linkOperState is in the down state. The polling state only occurs when the Local Management Interface (LMI) is enabled and the physical link is active. The polling state indicates LMI is polling for its peer. Once communication is established the linkOperState will transition to the active state. If the procedure attribute of the Lmi component is set to none, linkOperState will transition to the active state once the physical link becomes active.
frDteErrTable	1.3.6.1.4.1.562.2.4.1.101.26		not-accessible	This group contains the SNMP frErrEntry attributes for the FrDte component.
frDteErrEntry	1.3.6.1.4.1.562.2.4.1.101.26.1		not-accessible	An entry in the frDteErrTable.
INT frDteErrType	1.3.6.1.4.1.562.2.4.1.101.26.1.2	INTEGER	read-only	The type of error that was last seen on this interface. The error types are as follows: receiveShort: This error indicates a received frame was discarded because it was less than four octets long or it was missing the Organizationally Unique Identifier (OUI) for a SNAP header. receiveLong: This error indicates a received frame was discarded because it was longer than expected. This error is currently not used on this interface. illegalDlci: This error indicates that a received frame was discarded because it's Q.922 address was not two octets in length. This error could also indicate that a frame was discarded because it was received on a DLCI reserved for LMI which had not been provisioned active. dlcmiProtoErr: This error indicates an LMI frame was received with contents formatted incorrectly. dlcmiUnknownIe: This error indicates that an LMI frame was received which contained an unsupported Information Element (IE) type dlcmiSequenceErr: This error indicates that an LMI frame was received whose Keep Alive Sequence was incorrect. dlcmiUnknownRpt: This error indicates that an LMI frame was received which contained a Report-type Information Element with an invalid type of report. noErrorSinceReset: This error type indicates that there has not been an error since the interface has been reset. unknownError: This error type contains the cumulation of receive frame errors that did not fit one of the MIB error descriptions above. These errors include those counted by the following attributes: ulpUnknownProtocol - A received frame was discarded because the Upper Level Protocol (ULP) encapsulation used was unsupported. badFc - A received frame was discarded because the frame control character was incorrect. defragSequenceErrors - A fragment was received which was discarded due to an out of sequence error detection.
STR frDteErrData	1.3.6.1.4.1.562.2.4.1.101.26.1.3	HexString	read-only	An octet string containing the first part of the frame in which an error was last detected.
ENT frDteErrTime	1.3.6.1.4.1.562.2.4.1.101.26.1.4	EnterpriseDateAndTime	read-only	The time at which the last error was detected and recorded in errType.
C32 frDteErrDiscards	1.3.6.1.4.1.562.2.4.1.101.26.1.6	Counter32	read-only	Number of inbound frames dropped because of format errors or because the virtual circuit was not known. Format errors, in this case, are any errors which would prevent the system from recognizing the DLCI and placing the error in the discard category. This counter will wrap around to 0 when it exceeds its maximum count.
C32 frDteErrFaults	1.3.6.1.4.1.562.2.4.1.101.26.1.7	Counter32	read-only	This attribute counts the number of times LMI has taken down the interface. When the procedure attribute of the Lmi component is set to none, this counter will not be incremented. This counter will wrap around to 0 when it exceeds its maximum count.
ENT frDteErrFaultTime	1.3.6.1.4.1.562.2.4.1.101.26.1.8	EnterpriseDateAndTime	read-only	The last time the errFaults counter was incremented.
frDteErrStatsTable	1.3.6.1.4.1.562.2.4.1.101.27		not-accessible	This group contains error counters for the FrDte.
frDteErrStatsEntry	1.3.6.1.4.1.562.2.4.1.101.27.1		not-accessible	An entry in the frDteErrStatsTable.
C32 frDteXmitDiscardPvcDown	1.3.6.1.4.1.562.2.4.1.101.27.1.1	Counter32	read-only	Count of transmitted frames discarded because the Dlci or a component positioned in a hierarchically fashion above it (e.g. it's remote group or the FrDte component) was administratively disabled. This counter will wrap around to 0 when it exceeds its maximum count.
C32 frDteXmitDiscardLmiInactive	1.3.6.1.4.1.562.2.4.1.101.27.1.2	Counter32	read-only	Count of transmitted frames discarded because the Local Management Interface (LMI) was not yet active (i.e. LMI was still in the polling state). This counter will wrap around to 0 when it exceeds its maximum count.
C32 frDteXmitDiscardFramerDown	1.3.6.1.4.1.562.2.4.1.101.27.1.3	Counter32	read-only	Count of transmitted frames discarded because the framer component was down. This counter will wrap around to 0 when it exceeds its maximum count.
C32 frDteXmitDiscardPvcInactive	1.3.6.1.4.1.562.2.4.1.101.27.1.4	Counter32	read-only	Count of transmitted frames discarded because the Local Management Interface (LMI) had inactivated or invalidated the Dlci. This counter will wrap around to 0 when it exceeds its maximum count.
C32 frDteXmitDiscardCirExceeded	1.3.6.1.4.1.562.2.4.1.101.27.1.5	Counter32	read-only	Count of transmitted frames discarded because CIR was enabled on a Dlci without a HibernationQueue subcomponent and the traffic exceeded the combined Committed and Excess Burst thresholds. This counter will wrap around to 0 when it exceeds its maximum count.
C32 frDteRecvDiscardPvcDown	1.3.6.1.4.1.562.2.4.1.101.27.1.6	Counter32	read-only	Count of received frames discarded because the Dlci or a component positioned in a hierarchically fashion above it (e.g. it's remote group or the FrDte component) was administratively disabled. This counter will wrap around to 0 when it exceeds its maximum count.
C32 frDteRecvDiscardLmiInactive	1.3.6.1.4.1.562.2.4.1.101.27.1.7	Counter32	read-only	Count of received frames discarded because the Local Management Interface (LMI) was not yet active (i.e. LMI was still in the polling state). This counter will wrap around to 0 when it exceeds its maximum count.
C32 frDteRecvDiscardPvcInactive	1.3.6.1.4.1.562.2.4.1.101.27.1.8	Counter32	read-only	Count of received frames discarded because the Local Management Interface (LMI) had inactivated or invalidated the Dlci. This counter will wrap around to 0 when it exceeds its maximum count.
C32 frDteBadFc	1.3.6.1.4.1.562.2.4.1.101.27.1.9	Counter32	read-only	Count of received frames discarded because the frame control character was incorrect. This may indicate that the other side of the link is configured for a different link level protocol. This counter will wrap around to 0 when it exceeds its maximum count.
C32 frDteUlpUnknownProtocol	1.3.6.1.4.1.562.2.4.1.101.27.1.10	Counter32	read-only	Count of received frames discarded because the Upper Level Protocol (ULP) encapsulation used was unsupported. This counter will wrap around to 0 when it exceeds its maximum count.
C32 frDteDefragSequenceErrors	1.3.6.1.4.1.562.2.4.1.101.27.1.11	Counter32	read-only	Count of fragments received which were discarded due to out of sequence error detection. This counter will wrap around to 0 when it exceeds its maximum count.
C32 frDteReceiveShort	1.3.6.1.4.1.562.2.4.1.101.27.1.12	Counter32	read-only	Count of received frames (including LMI frames) discarded because they were less than four octets long or they were missing the Organizationally Unique Identifier (OUI) for a SNAP header. This counter will wrap around to 0 when it exceeds its maximum count.
C32 frDteIllegalDlci	1.3.6.1.4.1.562.2.4.1.101.27.1.13	Counter32	read-only	Count of received frames discarded because their Q.922 address was not two octets in length. This count also includes frames discarded because they were received on a Dlci reserved for LMI which had not been provisioned active. This counter will wrap around to 0 when it exceeds its maximum count.
C32 frDteDlcmiProtoErr	1.3.6.1.4.1.562.2.4.1.101.27.1.14	Counter32	read-only	Count of received LMI frames whose contents were formatted incorrectly. This counter will wrap around to 0 when it exceeds its maximum count.
C32 frDteDlcmiUnknownIe	1.3.6.1.4.1.562.2.4.1.101.27.1.15	Counter32	read-only	Count of received LMI frames which contained an unsupported Information Element (IE) type. This counter will wrap around to 0 when it exceeds its maximum count.
C32 frDteDlcmiSequenceErr	1.3.6.1.4.1.562.2.4.1.101.27.1.16	Counter32	read-only	Count of received LMI frames whose Keep Alive Sequence was incorrect. This counter will wrap around to 0 when it exceeds its maximum count.
C32 frDteDlcmiUnknownRpt	1.3.6.1.4.1.562.2.4.1.101.27.1.17	Counter32	read-only	Count of received LMI frames which contained a Report-type Information Element with an invalid type of report. This counter will wrap around to 0 when it exceeds its maximum count.
frameRelayDteMIB	1.3.6.1.4.1.562.2.4.2.32
frameRelayDteGroup	1.3.6.1.4.1.562.2.4.2.32.1
frameRelayDteGroupBE	1.3.6.1.4.1.562.2.4.2.32.1.5
frameRelayDteGroupBE00	1.3.6.1.4.1.562.2.4.2.32.1.5.1
frameRelayDteGroupBE00A	1.3.6.1.4.1.562.2.4.2.32.1.5.1.2
frameRelayDteCapabilities	1.3.6.1.4.1.562.2.4.2.32.3
frameRelayDteCapabilitiesBE	1.3.6.1.4.1.562.2.4.2.32.3.5
frameRelayDteCapabilitiesBE00	1.3.6.1.4.1.562.2.4.2.32.3.5.1
frameRelayDteCapabilitiesBE00A	1.3.6.1.4.1.562.2.4.2.32.3.5.1.2

RFC description

Manages Frame Relay DTE interface configuration for Nortel Magellan Passport telecommunications equipment.

Start monitoring Nortel Magellan Passport multiservice switch (Frame Relay DTE/DLCI access) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Nortel-Magellan-Passport-FrameRelayDteMIB

What Is Nortel-Magellan-Passport-FrameRelayDteMIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description