All MIBs › HPN-ICF-DOT11-RRM-MIB
Last Updated: 2010-09-25
Category: Technology: Wireless, Vendor: H3C/HH3C, Vendor: HP/HPE, Wireless and WLAN
Description: HP Networking ICF SNMP MIB for 802.11 Radio Resource Management (RRM) including channel and power auto-tuning on HP WLAN devices.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is HPN-ICF-DOT11-RRM-MIB?
HPN-ICF-DOT11-RRM-MIB is an HPE/H3C Comware ICF private MIB for 802.11 Radio Resource Management, which automatically tunes wireless channel and power settings on access points to optimize RF performance and reduce interference. It exposes configuration objects for auto channel/power tuning (hpnicfDot11RRM11aPwrConstrt, 11aSpectrumManag, AutoChlAvoid11h), scan parameters (ScanChl, ScanRptIntvel), per-radio-standard rate/MCS limits (11nMadtMaxMcs, 11nSuptMaxMcs, 11acMadtMaxNss), and interference thresholds (hpnicfDot11APInterfNumThreshhd, StaInterfNumThreshhd). Its monitoring value lies in RF/software health: tracking whether automatic channel and power adjustments are converging and whether interference thresholds are exceeded, which explains degraded wireless client throughput. It is tied to the IEEE 802.11a/g/n/ac PHY standards referenced in its object names and to the vendor's broader WLAN MIB family. It is deployed on HPE/H3C Comware WLAN Access Controllers managing enterprise Wi-Fi. Engineers can download the HPN-ICF-DOT11-RRM-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in HPN-ICF-DOT11-RRM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- HPE/H3C Comware WLAN Access Controllers
- HPE/H3C access points (Fit AP)
Monitoring Examples
An administrator checks hpnicfDot11RRMScanChl and ScanRptIntvel to confirm how often APs scan RF conditions, and reviews hpnicfDot11APInterfNumThreshhd/StaInterfNumThreshhd to see the interference levels that trigger automatic remediation. Comparing hpnicfDot11RRM11nMadtMaxMcs against 11nSuptMaxMcs helps confirm whether RRM is capping negotiated data rates below what clients support, explaining unexpectedly low throughput. Persistent breaches of the interference thresholds point to a noisy RF environment needing channel replanning.
What Can Be Monitored
- auto channel/power tuning configuration
- RF scan interval and channel list
- interference thresholds for AP/station
- maximum negotiated MCS/data rate per radio standard
This MIB depends on
Related MIBs
Imported Objects
| HpnicfDot11ChannelScopeType | |
| HpnicfDot11ObjectIDType | |
| HpnicfDot11RadioElementIndex | |
| HpnicfDot11RadioScopeType | |
| HpnicfDot11RadioType | |
| HpnicfDot11SSIDStringType | |
| hpnicfDot11 | MODULE-IDENTITY |
| hpnicfDot11APElementIndex | OBJECT-TYPE |
From SNMPv2-SMI
| Integer32 | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| DateAndTime | |
| MacAddress | |
| RowStatus | |
| TruthValue |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| I32 hpnicfDot11APInterfNumThreshhd | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.9 | Integer32 | read-write | Represents threshold of AP interference . If the value of AP interference exceeds this threshold, AP interference trap will be sent. If the value of this node is zero, AP interference trap will be sent immediately. |
| hpnicfDot11MonitorDetectedDevEntry | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1 | not-accessible | Each entry contains information of detected devices. | |
| hpnicfDot11MonitorDetectedDevTable | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1 | not-accessible | This table shows the devices of AP detected | |
| hpnicfDot11MonitorDetectedGroup | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.4 | |||
| I32 hpnicfDot11MonitorDevBeaconIntvl | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.9 | Integer32 | read-only | Represents the beacon interval for the detected device(not include the device which type is client). |
| MAC hpnicfDot11MonitorDevBSSID | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.5 | MacAddress | read-only | Represents the basic service set identifier of the detected device. |
| HPN hpnicfDot11MonitorDevChannel | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.6 | HpnicfDot11ChannelScopeType | read-only | Represents the channel in which the device was last detected. AP will choose the channel which has maximum signal strength as effective channel, as there is interference between adjacent channels. |
| T/F hpnicfDot11MonitorDevClear | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.12 | TruthValue | read-write | This object is used to clear the information of the device detected in the WLAN. It will return false for get operation. |
| DAT hpnicfDot11MonitorDevFstDctTime | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.10 | DateAndTime | read-only | Represents the time at which the device was first detected. |
| DAT hpnicfDot11MonitorDevLstDctTime | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.11 | DateAndTime | read-only | Represents the time at which the device was detected last time. |
| MAC hpnicfDot11MonitorDevMAC | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.1 | MacAddress | not-accessible | Represents MAC address of the device detected. |
| I32 hpnicfDot11MonitorDevMaxRSSI | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.8 | Integer32 | read-only | Represents the maximum detected RSSI of the device in a scan report cycle. |
| I32 hpnicfDot11MonitorDevSNR | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.13 | Integer32 | read-only | Represents the SNR of the device in a scan report cycle. |
| OCT hpnicfDot11MonitorDevSSID | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.4 | OCTET STRING | read-only | Represents the service set identifier for the ESS of the device which type is ap or adhoc. |
| INT hpnicfDot11MonitorDevType | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.2 | INTEGER | read-only | Represents type of the device detected. |
| OCT hpnicfDot11MonitorDevVendor | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.3 | OCTET STRING | read-only | Represents vendor of the detected device. |
| HPN hpnicfDot11MonitorRadioId | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.7 | HpnicfDot11RadioScopeType | read-only | Represents the radio ID of the AP that detected the device. |
| I32 hpnicfDot11NewPower | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.3.1 | Integer32 | accessible-for-notify | Power of the radio after the change of power. |
| I32 hpnicfDot11OldPower | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.3.2 | Integer32 | accessible-for-notify | Power of the radio before the change of power. |
| hpnicfDot11RRM | 1.3.6.1.4.1.11.2.14.11.15.2.75.8 | This MIB file is to provide the object definition of WLAN radio resource management (RRM). | ||
| I32 hpnicfDot11RRM11acMadtMaxNss | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.12 | Integer32 | read-write | Specify the maximum NSS index for 802.11ac mandatory rates. The value 0 indicates that no maximum NSS index is specified. No maximum NSS index is specified for 802.11ac mandatory rates by default. The specified maximum NSS index for 802.11ac supported rates must be no less than the specified maximum NSS index for 802.11ac mandatory rates. |
| I32 hpnicfDot11RRM11acMultiCastNss | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.14 | Integer32 | read-write | Specify the NSS index for 802.11ac multicast rates. The value 0 indicates that no NSS index is specified. No NSS index is specified for 802.11ac multicast rates by default. The specified NSS index for 802.11ac multicast rates must be no less than the specified maximum NSS index for 802.11ac mandatory rates. Before configuring the NSS index for 802.11ac multicast rates, the maximum NSS index for 802.11ac mandatory rates must be configured. Besides, it must be configured together with the node below. |
| I32 hpnicfDot11RRM11acMultiCastVhtMcs | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.15 | Integer32 | read-write | Specify the MCS index for 802.11ac multicast rates. The value 255 indicates that no MCS index is specified. No MCS index is specified for 802.11ac multicast rates by default. Besides, it must be configured together with the node above. |
| I32 hpnicfDot11RRM11acSuptMaxNss | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.13 | Integer32 | read-write | Specify the maximum NSS index for 802.11ac supported rates. The specified maximum NSS index for 802.11ac supported rates must be no less than the specified maximum NSS index for 802.11ac mandatory rates. |
| I32 hpnicfDot11RRM11aPwrConstrt | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.4 | Integer32 | read-write | Configure the power constraint for all 802.11a radios. The configured power constraint is advertised in beacons if spectrum management is enabled. The range of power constraint is 0 to MAX-POWER-1 (where the MAX-POWER is defined by the regulatory domain). |
| T/F hpnicfDot11RRM11aSpectrumManag | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.5 | TruthValue | read-write | Enable/Disable spectrum management for 802.11a radios. When spectrum management is enabled, the WLAN sub-system advertises power capabilities of the AP and power constraints applicable to all devices in the BSS based on regulatory domain specification. |
| T/F hpnicfDot11RRM11gProtect | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.3 | TruthValue | read-write | Enable/Disable dot11g protection. |
| I32 hpnicfDot11RRM11nMadtMaxMcs | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.1 | Integer32 | read-write | Specify the maximum modulation and coding scheme (MCS) index for 802.11n mandatory rates. The value 255 indicates that no maximum MCS index is specified. No maximum MCS index is specified for 802.11n mandatory rates by default. Besides 255, the specified maximum MCS index for 802.11n supported rates must be no less than the specified maximum MCS index for 802.11n mandatory rates. |
| U32 hpnicfDot11RRM11nMultiCastMcs | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.11 | Unsigned32 | read-write | Specify the modulation and coding scheme (MCS) index for 802.11n multicast rates. The value 4294967295 indicates that no MCS index is specified. No MCS index is specified for 802.11n multicast rates by default. Besides 4294967295, the specified MCS index for 802.11n multicast rates must be no less than the specified maximum MCS index for 802.11n mandatory rates. Before configure the MCS index for 802.11n multicast rates, the maximum MCS index for 802.11n mandatory rates must be configured |
| I32 hpnicfDot11RRM11nSuptMaxMcs | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.2 | Integer32 | read-write | Specify the maximum Modulation and Coding Scheme (MCS) index for 802.11n supported rates. The specified maximum MCS index for 802.11n supported rates must be no less than the specified maximum MCS index for 802.11n mandatory rates. |
| I32 hpnicfDot11RRMAdjChlIntfTrapThhd | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.5.1.5 | Integer32 | read-write | Represents threshold of adjacent interference trap with current ap. If signal strength of the device exceeds this threshold, corresponding trap will be sent. |
| hpnicfDot11RRMAPCfg2Entry | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.5.1 | not-accessible | Each entry contains information of RRM parameters for AP. | |
| hpnicfDot11RRMAPCfg2Table | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.5 | not-accessible | This table defines the RRM parameters for AP. | |
| hpnicfDot11RRMAPCfgEntry | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.3.1 | not-accessible | Each entry contains information of RRM parameters for AP. | |
| hpnicfDot11RRMAPCfgTable | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.3 | not-accessible | This table defines the RRM parameters for AP. | |
| I32 hpnicfDot11RRMAPIntfThreshold | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.5.1.2 | Integer32 | read-write | Represents threshold of AP interference . If the number of AP interference exceeds this threshold, AP interference trap will be sent. |
| HPN hpnicfDot11RRMAPSerialID | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.5.1.1 | HpnicfDot11ObjectIDType | not-accessible | Serial ID of the AP. |
| INT hpnicfDot11RRMAPWorkMode | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.3.1.1 | INTEGER | read-write | AP work mode. |
| T/F hpnicfDot11RRMAutoChlAvoid11h | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.6 | TruthValue | read-write | Configure the auto-channel set as non-dot11h channels, this is, only the non-dot11h channels belonging to the country code are scanned during initial channel selection and one of them is selected. |
| I32 hpnicfDot11RRMCfgAdjacencyFctr | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.13 | Integer32 | read-write | Configure the adjacency factor for the band. If transmit power control (TPC) is configured, power will be adjusted when the nth neighbor is detected. The value n is the adjacency factor. |
| INT hpnicfDot11RRMCfgChlMode | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.3 | INTEGER | read-write | Configure the mode of channel selection. This node can be configured only when dynamic channel selection is enabled. |
| T/F hpnicfDot11RRMCfgChlState | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.2 | TruthValue | read-write | Enable/Disable dynamic channel selection. |
| I32 hpnicfDot11RRMCfgIntrfThres | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.9 | Integer32 | read-write | Configure the interface threshold. By default, interference observed on an operating channel is considered during dynamic frequency selection and transmit power control. If the interference percentage on the channel reaches the set threshold, RRM will perform resource adjustment to control the situation. |
| I32 hpnicfDot11RRMCfgIntrvl | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.8 | Integer32 | read-write | Configure the calibration interval. |
| I32 hpnicfDot11RRMCfgNoiseThres | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.10 | Integer32 | read-write | Configure the noise threshold. |
| I32 hpnicfDot11RRMCfgPERThres | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.11 | Integer32 | read-write | Configure the CRC error threshold. If the percentage of CRC errors reaches the threshold, RRM will perform resource adjustment to control the situation. |
| INT hpnicfDot11RRMCfgPwrMode | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.6 | INTEGER | read-write | Configure the mode of transmit power control. This node can be configured only when dynamic power selection is enabled. |
| T/F hpnicfDot11RRMCfgPwrState | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.5 | TruthValue | read-write | Enable/Disable dynamic power selection for the band. |
| I32 hpnicfDot11RRMCfgToleranceFctr | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.12 | Integer32 | read-write | Configure the tolerance level. During dynamic frequency selection (DFS), the channel will be changed only if there is a better channel having lesser interference and packet error rate than those specified by the user. |
| U32 hpnicfDot11RRMChlProntoRadioElmt | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.4 | Unsigned32 | read-write | Specify the AP and radio that will change channel at next calibration cycle. 0 is returned when getting the value of this node. This node can be configured only when the mode of channel selection control is user-triggered. When configuring, the higher 24 bits stand for the AP index, and the last 8 bits stand for the radio index. 4294967295 stand for configuring each radio on all APs. |
| hpnicfDot11RRMChlQltyNotifications | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.1 | |||
| hpnicfDot11RRMChlQltyNtfPrefix | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.1.0 | |||
| I32 hpnicfDot11RRMChlRptChlNum | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.2 | Integer32 | accessible-for-notify | Channel number. |
| INT hpnicfDot11RRMChlRptChlQlty | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.4 | INTEGER | read-only | Channel quality. |
| INT hpnicfDot11RRMChlRptChlType | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.3 | INTEGER | read-only | Channel type. |
| hpnicfDot11RRMChlRptEntry | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1 | not-accessible | Each entry contains information of RRM channel information of the radio on the AP. | |
| I32 hpnicfDot11RRMChlRptIntrf | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.8 | Integer32 | read-only | Interference observed on the channel in percentage. |
| I32 hpnicfDot11RRMChlRptLoad | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.6 | Integer32 | read-only | Load observed on the channel in percentage. |
| I32 hpnicfDot11RRMChlRptNbrCnt | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.5 | Integer32 | read-only | Number of neighbors found on the channel. |
| I32 hpnicfDot11RRMChlRptNoise | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.11 | Integer32 | read-only | Noise observed on the channel. |
| I32 hpnicfDot11RRMChlRptPER | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.9 | Integer32 | read-only | Packet error rate observed on the channel in percentage. |
| INT hpnicfDot11RRMChlRptRadarIndtcr | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.12 | INTEGER | read-write | Radar detection status. |
| I32 hpnicfDot11RRMChlRptRetryRate | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.10 | Integer32 | read-only | Percentage of retransmission happened on the channel. |
| hpnicfDot11RRMChlRptTable | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1 | not-accessible | This table shows the RRM channel information of each radio on all APs. | |
| I32 hpnicfDot11RRMChlRptUtlz | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.7 | Integer32 | read-only | Utilization of the channel in percentage. |
| I32 hpnicfDot11RRMCoChlIntfTrapThhd | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.5.1.4 | Integer32 | read-write | Represents threshold of interference trap with current ap. If signal strength of the device exceeds this threshold, corresponding trap will be sent. |
| hpnicfDot11RRMConfigGroup | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1 | |||
| hpnicfDot11RRMDetectGroup | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2 | |||
| hpnicfDot11RRMGlobalCfgPara | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1 | |||
| DAT hpnicfDot11RRMHistoryChgDateTime | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.12 | DateAndTime | read-only | The time when the channel or power change occurred. |
| BIT hpnicfDot11RRMHistoryChgReason | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.11 | Bits | read-only | Reason for the change of channel or power. The various bit positions are: |0 |Others | |1 |Coverage | |2 |Radar | |3 |Retransmission | |4 |Packets discarded | |5 |Interference | 0 is returned when the history record type is after. |
| HPN hpnicfDot11RRMHistoryChl | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.3 | HpnicfDot11ChannelScopeType | read-only | Channel on which the radio operates before/after the change of channel or power. |
| hpnicfDot11RRMHistoryEntry | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1 | not-accessible | Each entry shows the details of channel and power changes. | |
| I32 hpnicfDot11RRMHistoryId | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.1 | Integer32 | not-accessible | History number of the change. |
| I32 hpnicfDot11RRMHistoryIntrf | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.7 | Integer32 | read-only | Interference observed on the radio in percentage before/after the change of channel or power. |
| I32 hpnicfDot11RRMHistoryLoad | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.5 | Integer32 | read-only | Load observed on the radio in percentage before/after the change of channel or power. |
| I32 hpnicfDot11RRMHistoryNoise | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.8 | Integer32 | read-only | Noise observed on the radio before/after the change of channel or power. |
| I32 hpnicfDot11RRMHistoryPER | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.9 | Integer32 | read-only | Packet error rate observed on the radio in percentage before/after the change of channel or power. |
| I32 hpnicfDot11RRMHistoryPwr | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.4 | Integer32 | read-only | Power of the radio before/after the change of channel or power. |
| INT hpnicfDot11RRMHistoryRecIndctr | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.2 | INTEGER | not-accessible | History record type of the change. |
| I32 hpnicfDot11RRMHistoryRetryRate | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.10 | Integer32 | read-only | Percentage of retransmission happened on the radio before/after the change of channel or power. |
| hpnicfDot11RRMHistoryTable | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3 | not-accessible | This table shows the details of the latest three channel changes and power changes applied on all APs, including time of change, reason of the change and the channel, power, interference parameters. | |
| I32 hpnicfDot11RRMHistoryUtlz | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.6 | Integer32 | read-only | Utilization of the radio in percentage before/after the change of channel or power. |
| NTF hpnicfDot11RRMIntrfLimit | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.1.0.1 | This notification will be sent when interference on the radio exceeds the limit. | ||
| MAC hpnicfDot11RrmNbrBSSID | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.2.1.1 | MacAddress | not-accessible | MAC address of the AP. |
| HPN hpnicfDot11RrmNbrChl | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.2.1.2 | HpnicfDot11ChannelScopeType | read-only | Channel number on which the neighbor was found. |
| hpnicfDot11RRMNbrInfoEntry | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.2.1 | not-accessible | Each entry contains information of RRM neighbor information of the radio on an AP. | |
| hpnicfDot11RRMNbrInfoTable | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.2 | not-accessible | This table shows the RRM neighbor information of each radio on all APs. | |
| I32 hpnicfDot11RRMNbrIntrf | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.2.1.3 | Integer32 | read-only | Interference observed on the channel in percentage by neighbor. |
| I32 hpnicfDot11RrmNbrRSSI | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.2.1.4 | Integer32 | read-only | Signal strength of the AP in dBm. |
| STR hpnicfDot11RrmNbrSSID | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.2.1.6 | HpnicfDot11SSIDStringType | read-only | SSID of the Neighbor. |
| INT hpnicfDot11RrmNbrType | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.2.1.5 | INTEGER | read-only | Type of the AP, managed or unmanaged. |
| NTF hpnicfDot11RRMNoiseLimit | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.1.0.3 | This notification will be sent when noise on the radio exceeds the limit. | ||
| hpnicfDot11RRMNotificationsVar | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.3 | |||
| hpnicfDot11RRMNotifyGroup | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.3 | |||
| NTF hpnicfDot11RRMPERLimit | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.1.0.2 | This notification will be sent when packet error rate on the radio exceeds the limit. | ||
| NTF hpnicfDot11RRMPowerChange | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.2.0.1 | This notification will be sent when power changed on the radio automatically. | ||
| U32 hpnicfDot11RRMPwrProntoRadioElmt | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.7 | Unsigned32 | read-write | Specify the AP and radio that will change power at next calibration cycle. 0 is returned when getting the value of this node. This node can be configured only when the mode of transmit power control is user-triggered. When configuring, the higher 24 bits stand for the AP index, and the last 8 bits stand for the radio index. 4294967295 stand for configuring each radio on all APs. |
| hpnicfDot11RRMRadioCfgEntry | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1 | not-accessible | Configure WLAN RRM based radio type. When 802.11b parameter is modified, 802.11g parameter will be changed at the same time. In the same way, when 802.11g parameter is modified, 802.11b parameter will be changed at the same time. | |
| hpnicfDot11RRMRadioCfgTable | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2 | not-accessible | Configure WLAN RRM based radio type. When 802.11b parameter is modified, 802.11g parameter will be changed at the same time. In the same way, when 802.11g parameter is modified, 802.11b parameter will be changed at the same time. | |
| HPN hpnicfDot11RRMRadioIndex | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.1 | HpnicfDot11RadioElementIndex | accessible-for-notify | Represents index of the radio. |
| HPN hpnicfDot11RRMRadioNbrAPID | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.4.1.1 | HpnicfDot11ObjectIDType | not-accessible | AP serial id. |
| hpnicfDot11RRMRadioNbrInfoEntry | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.4.1 | not-accessible | Each entry contains information of RRM neighbor information of the radio on an AP. | |
| hpnicfDot11RRMRadioNbrInfoTable | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.4 | not-accessible | This table shows the RRM neighbor information of each radio on all APs. | |
| HPN hpnicfDot11RRMRadioNbrRadioID | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.4.1.2 | HpnicfDot11RadioScopeType | not-accessible | Radio Id on AP. |
| OCT hpnicfDot11RRMRadioNbrSSID | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.4.1.3 | OCTET STRING | read-only | All neighbour SSIDs scanned by the selected radio. |
| HPN hpnicfDot11RRMRadioType | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.1 | HpnicfDot11RadioType | not-accessible | 802.11 radio type. |
| hpnicfDot11RRMResChgNotifications | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.2 | |||
| hpnicfDot11RRMResChgNtfPrefix | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.2.0 | |||
| INT hpnicfDot11RRMScanChl | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.7 | INTEGER | read-write | Set the scan mode. auto: When this option is set, all channels of the country code being set are scanned. all: When this option is set, all the channels of the radio band are scanned. |
| I32 hpnicfDot11RRMScanRptIntvel | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.8 | Integer32 | read-write | Set the scan report interval. |
| OCT hpnicfDot11RRMSDRadioGroupDesc | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.4.1.2 | OCTET STRING | read-create | Represents the description of RRM self-decisive radio group. |
| hpnicfDot11RRMSDRadioGroupEntry | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.4.1 | not-accessible | Each entry contains information of one RRM self-decisive radio group. | |
| U32 hpnicfDot11RRMSDRadioGroupId | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.4.1.1 | Unsigned32 | not-accessible | Represents RRM self-decisive radio group ID. |
| hpnicfDot11RRMSDRadioGroupTable | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.4 | not-accessible | This table defines RRM self-decisive radio group. | |
| ROW hpnicfDot11RRMSDRdGroupRowStatus | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.4.1.5 | RowStatus | read-create | The row status of this table entry. |
| U32 hpnicfDot11RRMSDRdGrpChlHolddownTm | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.4.1.3 | Unsigned32 | read-create | Represents the channel holddown time of RRM self-decisive radio group. |
| U32 hpnicfDot11RRMSDRdGrpPwrHolddownTm | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.4.1.4 | Unsigned32 | read-create | Represents the power holddown time of RRM self-decisive radio group. |
| I32 hpnicfDot11RRMStaIntfThreshold | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.5.1.3 | Integer32 | read-write | Represents threshold of STA interference. If the number of STA interference exceeds this threshold, station interference trap will be sent. |
| I32 hpnicfDot11StaInterfNumThreshhd | 1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.10 | Integer32 | read-write | Represents threshold of STA interference. If the value of STA interference exceeds this threshold, STA interference trap will be sent. If the value of this node is zero, STA interference trap will be sent immediately. |
RFC description
WLAN radio resource management (RRM) for HP wireless access point configuration.
Start monitoring HPE/H3C Comware WLAN Access Controller / Fit AP (Radio Resource Management) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.