| OID symbolic | OID numeric | Type | Access | Description |
|---|
| hpicfFaultFinderMib | 1.3.6.1.4.1.11.2.14.10.2.12 | | | This MIB module contains object definitions for
managing the Fault Finder feature in web-capable
HP devices. |
| hpicfFaultFinderConformance | 1.3.6.1.4.1.11.2.14.10.2.12.1 | | | |
| hpicfFaultFinderCompliances | 1.3.6.1.4.1.11.2.14.10.2.12.1.1 | | | |
| hpicfFaultFinderCompliance | 1.3.6.1.4.1.11.2.14.10.2.12.1.1.1 | | | The compliance statement for devices
implementing the HP Fault Finder capability. |
| hpicfFaultFinder2Compliance | 1.3.6.1.4.1.11.2.14.10.2.12.1.1.2 | | | The compliance statement for devices
implementing the HP Fault Finder capability. |
| hpicfFaultStatusCompliance | 1.3.6.1.4.1.11.2.14.10.2.12.1.1.3 | | | The compliance statement for devices
implementing the switch fault status. |
| hpicfFaultFinder3Compliance | 1.3.6.1.4.1.11.2.14.10.2.12.1.1.4 | | | The compliance statement for devices
implementing the HP Fault Finder capability. |
| hpicfFaultFinder4Compliance | 1.3.6.1.4.1.11.2.14.10.2.12.1.1.5 | | | The compliance statement for devices
implementing the HP Fault Finder capability. |
| hpicfFaultFinderGroups | 1.3.6.1.4.1.11.2.14.10.2.12.1.2 | | | |
| hpicfFaultConfigGroup | 1.3.6.1.4.1.11.2.14.10.2.12.1.2.1 | | | A collection of objects for configuring the
Fault Finder feature. |
| hpicfFaultLogGroup | 1.3.6.1.4.1.11.2.14.10.2.12.1.2.2 | | | A collection of objects for accessing the log of
discovered faults. |
| hpicfFaultNotifyGroup | 1.3.6.1.4.1.11.2.14.10.2.12.1.2.3 | | | A collection of notifications used to indicate
the discovery of a network fault. |
| hpicfFaultConfig2Group | 1.3.6.1.4.1.11.2.14.10.2.12.1.2.4 | | | A collection of objects for configuring the
Fault Finder feature, including the ability
to reduce a port's media speed in the event
of a fault. |
| hpicfFaultStatusGroup | 1.3.6.1.4.1.11.2.14.10.2.12.1.2.5 | | | A collection of objects used to indicate
fault status. |
| hpicfFaultConfig3Group | 1.3.6.1.4.1.11.2.14.10.2.12.1.2.6 | | | A collection of objects for configuring the
Fault Finder broadcast storm feature on a per
per port basis, including the ability
to disable a port in the event of a fault. |
| hpicfFaultConfig4Group | 1.3.6.1.4.1.11.2.14.10.2.12.1.2.7 | | | A collection of objects for configuring the
Fault Finder Link Flap feature on a per
per port basis, including the ability
to disable a port in the event of a fault. |
| hpicfFaultFinder | 1.3.6.1.4.1.11.2.14.11.1.7 | | | |
| hpicfFfControlTable | 1.3.6.1.4.1.11.2.14.11.1.7.1 | | not-accessible | This table contains one entry per fault type
that this agent is capable of monitoring. |
| hpicfFfControlEntry | 1.3.6.1.4.1.11.2.14.11.1.7.1.1 | | not-accessible | Configuration information for a particular fault
type. |
| HPI hpicfFfControlIndex | 1.3.6.1.4.1.11.2.14.11.1.7.1.1.1 | HpicfFaultType | not-accessible | The type of fault for which this entry contains
configuration information. |
| HPI hpicfFfAction | 1.3.6.1.4.1.11.2.14.11.1.7.1.1.2 | HpicfFaultAction | read-write | This object is used to configure the action,
if any, to be taken if a fault of this type is
detected by the agent. Setting an instance of
this object to 'none' will clear any previous
state of the associated fault on all ports.
This object is used to enable or disable the
port disable feature for this fault type.
Setting this object to 'warnAndDisable' will
enable the port disable feature for this fault
type. This feature is intended to allow an agent
to disable ports that are being disruptive to the
rest of the network.
Note that not all agents will support setting
this object to 'warnAndDisable'. The agent
may choose not to disable a particular port for a
particular fault based on its knowledge of if/how
that fault disrupts the network. |
| HPI hpicfFfWarnTolerance | 1.3.6.1.4.1.11.2.14.11.1.7.1.1.3 | HpicfFaultTolerance | read-write | The tolerance level used to calculate the
fault warning threshold for this fault type.
The agent will periodically check relevant
statistics for each port for each type of fault.
If the warning threshold has been exceeded, and
fault warning action is enabled for that fault
type, an hpicfFaultFinderTrap notification will
be sent. In addition, an entry will be made in
the hpicfFfLogTable for the fault. Once a fault
warning has fired, a hysteresis mechanism assures
that another warning will not be fired until the
relevant counter drops below a hysteresis
threshold value. |
| HPI hpicfFfDisablePortTolerance | 1.3.6.1.4.1.11.2.14.11.1.7.1.1.4 | HpicfFaultTolerance | read-write | The tolerance level used to calculate the
port disable threshold for this fault type.
The value of an instance of this object MUST be
greater than the value of the corresponding
instance of the hpicfFfWarnTolerance.
The agent will periodically check relevant
statistics for each port for each type of fault.
If the port disable threshold has been exceeded,
and port disable is enabled for that fault type,
an hpicfFaultFinderTrap notification will be
sent. In addition, an entry will be made in the
hpicfFfLogTable for the fault.
Ports will not be disabled until at least one
polling interval after a warning has fired. In
addition, the agent may further delay disabling
a port in certain situations. For example, it
may choose to delay disabling a cascade port to
give the cascaded device a chance to correct the
problem. |
| HPI hpicfFfSpeedReduceTolerance | 1.3.6.1.4.1.11.2.14.11.1.7.1.1.5 | HpicfFaultTolerance | read-write | The tolerance level used to calculate the
speed reduction threshold for this fault type.
The value of an instance of this object MUST be
greater than the value of the corresponding
instance of the hpicfFfWarnTolerance, and
less than or equal to the corresponding instance
of hpicfFfDisablePortTolerance.
The agent will only reduce speed on a port if
auto-negotiation has been performed, and the
partners link abilities allow operation at a
slower media speed.
The agent will periodically check relevant
statistics for each port for each type of fault.
If the speed reduction threshold has been exceeded,
and speed reduction option is enabled for that
fault type, an hpicfFaultFinderTrap notification
will be sent. In addition, an entry will be made
in the hpicfFfLogTable for the fault.
The agent may elect not to reduce speed or
delay speed reduction of certain ports.
For example, it may choose to delay taking
action on a cascade port to give the cascaded
device a chance to correct the problem. |
| hpicfFfLogTable | 1.3.6.1.4.1.11.2.14.11.1.7.2 | | not-accessible | A log of fault warnings and ports disabled by
the Fault Finder. |
| hpicfFfLogEntry | 1.3.6.1.4.1.11.2.14.11.1.7.2.1 | | not-accessible | An entry in the Fault Finder log, containing
information about a single fault. |
| I32 hpicfFfLogIndex | 1.3.6.1.4.1.11.2.14.11.1.7.2.1.1 | Integer32 | not-accessible | An arbitrary value which uniquely identifies
this log entry. The index for a particular log
entry must not change, even though entries with
lower valued indices have been deleted. |
| TIM hpicfFfLogCreateTime | 1.3.6.1.4.1.11.2.14.11.1.7.2.1.2 | TimeStamp | read-only | The value of sysUpTime when this log entry was
added to the hpicfFfLogTable. |
| PHY hpicfFfLogPhysEntity | 1.3.6.1.4.1.11.2.14.11.1.7.2.1.3 | PhysicalIndex | read-only | The entPhysicalIndex of the device port or other
physical component on which the fault was
detected. On agents which do not implement the
Entity MIB, this will contain the ifIndex of the
offending port. |
| HPI hpicfFfLogFaultType | 1.3.6.1.4.1.11.2.14.11.1.7.2.1.4 | HpicfFaultType | read-only | The type of fault which was detected on the
physical entity indicated by
hpicfFfLogPhysEntity. |
| HPI hpicfFfLogAction | 1.3.6.1.4.1.11.2.14.11.1.7.2.1.5 | HpicfFaultAction | read-only | The action, if any, that was taken by the agent
when this fault was detected. |
| INT hpicfFfLogSeverity | 1.3.6.1.4.1.11.2.14.11.1.7.2.1.6 | INTEGER | read-only | The severity level of the fault. Port disables
will always be logged as 'critical'.
An agent may need to remove faults from the fault
log in order to reclaim resources. If so, it
must remove lower severity faults before removing
higher severity faults. Faults at the same
severity level should be removed from oldest to
newest. |
| INT hpicfFfLogStatus | 1.3.6.1.4.1.11.2.14.11.1.7.2.1.7 | INTEGER | read-write | Log entries will initially be created with the
value 'new'. A manager cannot set this object to
'new'. Setting this object to 'active' indicates
that the fault has been displayed to a user.
Setting this object to 'old' indicates that the
agent should remove this fault from the log. |
| PHY hpicfFfLogPhysClass | 1.3.6.1.4.1.11.2.14.11.1.7.2.1.8 | PhysicalClass | read-only | The PhysicalClass as defined by Entity MIB to
which this hpicfFfLogPhysIndex belongs. |
| INT hpicfFfLogInfoType | 1.3.6.1.4.1.11.2.14.11.1.7.2.1.9 | INTEGER | read-only | This field can be used to indicate the class of
information that 'hpicfFfLogInfo' holds |
| OCT hpicfFfLogInfo | 1.3.6.1.4.1.11.2.14.11.1.7.2.1.10 | OCTET STRING | read-only | This can be used to hold any relevant information
about the current fault |
| STR hpicfFfFaultInfoURL | 1.3.6.1.4.1.11.2.14.11.1.7.3 | HpicfUrlString | accessible-for-notify | A URL which a management station can use to
access additional information about the fault
which triggered the notification in which this
object was sent. |
| INT hpicfFfFaultLightStatus | 1.3.6.1.4.1.11.2.14.11.1.7.4 | INTEGER | read-only | This indicates the current state of the
switch fault light. Examples of faults
that could cause the LED to be turned on include
fan, power supply, and port link failures. |
| hpicfFfBcastStormControlPortConfig | 1.3.6.1.4.1.11.2.14.11.1.7.5 | | | |
| hpicfFfBcastStormControlPortConfigTable | 1.3.6.1.4.1.11.2.14.11.1.7.5.1 | | not-accessible | This table provides information about Broadcast Storm
control configuration of all ports. |
| hpicfFfBcastStormControlPortConfigEntry | 1.3.6.1.4.1.11.2.14.11.1.7.5.1.1 | | not-accessible | This object provides information about Broadcast Storm
Control configuration of each port. |
| NUM hpicfFfBcastStormControlPortIndex | 1.3.6.1.4.1.11.2.14.11.1.7.5.1.1.1 | InterfaceIndex | not-accessible | The ifIndex value which uniquely identifies a row in
the Interfaces Table. |
| INT hpicfFfBcastStormControlMode | 1.3.6.1.4.1.11.2.14.11.1.7.5.1.1.2 | INTEGER | read-write | The Broadcast Storm Control mode of a port.
A value of disable (1) indicates that no rising
threshold value is set for broadcast storm traffic on
this port. A value of bcastRisingLevelpercent (2)
indicates that the rising threshold rate for broadcast
storm traffic is configured in percentage of port
bandwidth. A value of bcastRisinglevelpps(3) indicates
that the rising threshold rate for broadcast storm
traffic is configured in packets per second. |
| I32 hpicfFfBcastStormControlRisingpercent | 1.3.6.1.4.1.11.2.14.11.1.7.5.1.1.3 | Integer32 | read-write | This is the rising threshold Level
in percent of bandwidth of the port.
hpicfFfBcastStormControlAction occurs when
broadcast traffic reaches this level. |
| I32 hpicfFfBcastStormControlRisingpps | 1.3.6.1.4.1.11.2.14.11.1.7.5.1.1.4 | Integer32 | read-write | This object indicates the rising threshold for Broadcast
Storm Control. This value is in packets-per-second of
received broadcast traffic.
hpicfFfBcastStormControlAction object takes action when
broadcast traffic reaches this level. |
| INT hpicfFfBcastStormControlAction | 1.3.6.1.4.1.11.2.14.11.1.7.5.1.1.5 | INTEGER | read-write | This object defines the action taken by the switch when
a broadcast storm occurs on a port.
A value of none (1) indicates that no action is performed.
A value of warn (2) indicates that an event is logged when
broadcast traffic crosses the threshold value set on that
port. A value of warnAndDisable (3) indicates that the
port is disabled and an event is logged as soon as the
broadcast traffic reaches the threshold value set on that
port. |
| U32 hpicfFfBcastStormControlPortDisableTimer | 1.3.6.1.4.1.11.2.14.11.1.7.5.1.1.6 | Unsigned32 | read-write | This object specifies the time period for which the port
remains in disabled state. A port is disabled when
broadcast traffic reaches the threshold value set on that
port. This time period is specified in seconds. The
default value is zero which means that the port remains
disabled and is not enabled again. |
| hpicfFfLinkFlapControlPortConfig | 1.3.6.1.4.1.11.2.14.11.1.7.6 | | | |
| hpicfFfLinkFlapControlPortConfigTable | 1.3.6.1.4.1.11.2.14.11.1.7.6.1 | | not-accessible | This table provides information about Link Flapping
control configuration of all ports. |
| hpicfFfLinkFlapControlPortConfigEntry | 1.3.6.1.4.1.11.2.14.11.1.7.6.1.1 | | not-accessible | This object provides information about Link Flapping
Control configuration of each port. |
| NUM hpicfFfLinkFlapControlPortIndex | 1.3.6.1.4.1.11.2.14.11.1.7.6.1.1.1 | InterfaceIndex | not-accessible | The ifIndex value which uniquely identifies a row in
the Interfaces Table. |
| INT hpicfFfLinkFlapControlSensitivity | 1.3.6.1.4.1.11.2.14.11.1.7.6.1.1.2 | INTEGER | read-write | The Link Flapping Control sensitivity of a port. A value
of low (1) indicates that the sensitivity of the link flap
threshold is set to 10 link flaps per 10 second interval.
A value of medium (2) indicates that the sensitivity of the
link flap threshold is set to 6 link flaps per 10 second
interval. A value of high (3) indicates that the sensitivity
of the link flap threshold is set to 3 link flaps per 10 second
interval. |
| INT hpicfFfLinkFlapControlAction | 1.3.6.1.4.1.11.2.14.11.1.7.6.1.1.3 | INTEGER | read-write | This object defines the action taken by the switch when
link flaps occurs on a port.
A value of none (1) indicates that no action is performed.
A value of warn (2) indicates that an event is logged when
the number of link flaps crosses the threshold rate set on
that port. A value of warnAndDisable (3) indicates that the
port is disabled and an event is logged as soon as the number
of link flaps reaches the threshold rate set on that port. |
| U32 hpicfFfLinkFlapControlPortDisableTimer | 1.3.6.1.4.1.11.2.14.11.1.7.6.1.1.4 | Unsigned32 | read-write | This object specifies the time period for which the port
remains in disabled state. A port is disabled when
the number of link flaps reaches the threshold rate set
on that port. This time period is specified in seconds. The
default value is zero which means that the port remains
disabled and is not enabled again. |
| NTF hpicfFaultFinderTrap | 1.3.6.1.4.1.11.2.14.12.1.0.5 | | | This notification is sent whenever the Fault
Finder creates an entry in the hpicfFfLogTable. |
