HP-ICF-OPENFLOW-MIB

All MIBs › HP-ICF-OPENFLOW-MIB

Organization: HP Networking

Last Updated: 2017-07-16

Category: Technology: SDN/OpenFlow, Vendor: HP/HPE

Description: HP ICF SNMP MIB for OpenFlow SDN controller configuration and flow table management on HP ProCurve OpenFlow-enabled switches.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HP-ICF-OPENFLOW-MIB?

HP-ICF-OPENFLOW-MIB is part of HP's Intelligent Chassis Family (ICF) enterprise MIB suite, covering OpenFlow software-defined networking configuration on HP ProCurve/HP Networking switches that support OpenFlow-enabled flow tables. It exposes a connection-interruption-mode configuration object plus notification and object groups related to OpenFlow controller connectivity, rather than a rich set of flow-table counters based on the objects provided. Its monitoring role centers on software/control-plane status: hpicfOpenFlowConnectionInterruptionMode governs and reflects how the switch behaves when its connection to the OpenFlow controller is lost, and the notifications group would alert on controller connectivity events, which is critical to knowing whether the switch is still following SDN flow instructions. It is a vendor extension aligned with the OpenFlow protocol standard from the Open Networking Foundation, so its concepts depend on that external specification. It is deployed on HP ProCurve/HP Networking switches used in SDN environments where OpenFlow controllers manage flow-based forwarding behavior. Network engineers evaluating or troubleshooting this functionality can download the HP-ICF-OPENFLOW-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in HP-ICF-OPENFLOW-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

HP ProCurve/HP Networking OpenFlow-enabled switch

Monitoring Examples

An SDN administrator would check hpicfOpenFlowConnectionInterruptionMode to confirm how the switch is configured to behave if it loses contact with its OpenFlow controller, since a fail-standalone setting could mean the switch reverts to normal L2/L3 forwarding unexpectedly. Notifications under hpicfOpenFlowNotifications would alert the controller/management system when such a connection interruption occurs, letting operators react quickly to a lost SDN control-plane session.

What Can Be Monitored

OpenFlow controller connection-interruption mode/behavior
OpenFlow connectivity notifications

Imported Objects

From HP-ICF-OID

hpSwitch

OBJECT-IDENTITY

From HP-ICF-TC

VidList

From IF-MIB

InterfaceIndex
ifIndex	OBJECT-TYPE

From INET-ADDRESS-MIB

InetAddress
InetAddressType
InetPortNumber

From Q-BRIDGE-MIB

PortList

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Counter64
Integer32
MODULE-IDENTITY
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DisplayString
RowStatus
TruthValue

How to Use in IPNetwork Monitor

Example using hpicfOpenFlowInstanceNumOfHwFlows OID:

Select an HP ProCurve/HP Networking OpenFlow-enabled switch as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type hpicfOpenFlowInstanceNumOfHwFlows into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. This object indicates the number of hardware flows in this OpenFlow instance. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter64-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
hpicfOpenFlowCompliance	1.3.6.1.4.1.11.2.14.11.5.1.89.2.1.1			This compliance statement is for devices supporting OpenFlow. The basic support for OpenFlow requires implementation of the objects listed in the mandatory groups.
hpicfOpenFlowCompliance1	1.3.6.1.4.1.11.2.14.11.5.1.89.2.1.2			This compliance statement is for devices supporting OpenFlow. The basic support for OpenFlow requires implementation of the objects listed in the mandatory groups.
hpicfOpenFlowCompliance2	1.3.6.1.4.1.11.2.14.11.5.1.89.2.1.3			This compliance statement is for devices supporting OpenFlow. The basic support for OpenFlow requires implementation of the objects listed in the mandatory groups.
hpicfOpenFlowCompliance3	1.3.6.1.4.1.11.2.14.11.5.1.89.2.1.4			This compliance statement is for devices supporting OpenFlow. The basic support for OpenFlow requires implementation of the objects listed in the mandatory groups.
hpicfOpenFlowCompliance4	1.3.6.1.4.1.11.2.14.11.5.1.89.2.1.5			This compliance statement is for devices supporting OpenFlow. The basic support for OpenFlow requires implementation of the objects listed in the mandatory groups.
hpicfOpenFlowCompliances	1.3.6.1.4.1.11.2.14.11.5.1.89.2.1
hpicfOpenFlowConformance	1.3.6.1.4.1.11.2.14.11.5.1.89.2
INT hpicfOpenFlowConnectionInterruptionMode	1.3.6.1.4.1.11.2.14.11.5.1.89.1.4.1.8	INTEGER	read-create	This MIB object is used to specify the type of fallback when the switch loses connection with the controller. In fail-secure mode, packets and messages destined to the current controller are dropped. Flows should continue to expire according to their timeouts in fail-secure mode. In fail-standalone mode, the switch acts as a legacy Ethernet switch or router.
hpicfOpenFlowControllerEntry	1.3.6.1.4.1.11.2.14.11.5.1.89.1.6.1		not-accessible	A set of objects that are used to configure OpenFlow Controllers.
hpicfOpenFlowControllerGroup	1.3.6.1.4.1.11.2.14.11.5.1.89.2.2.4			A collection of objects used to define controllers.
hpicfOpenFlowControllerGroup1	1.3.6.1.4.1.11.2.14.11.5.1.89.2.2.22			A collection of objects used to define controllers.
I32 hpicfOpenFlowControllerID	1.3.6.1.4.1.11.2.14.11.5.1.89.1.6.1.1	Integer32	not-accessible	Unique ID given to a Controller. This will be associated with an instance through hpicfOpenFlowInstanceControllerTable.
IP hpicfOpenFlowControllerInetAddress	1.3.6.1.4.1.11.2.14.11.5.1.89.1.6.1.3	InetAddress	read-create	IP Address of the controller.
IPt hpicfOpenFlowControllerInetAddressType	1.3.6.1.4.1.11.2.14.11.5.1.89.1.6.1.2	InetAddressType	read-create	Address type of this controller. This implementation supports only ipv4 type.
NUM hpicfOpenFlowControllerInterface	1.3.6.1.4.1.11.2.14.11.5.1.89.1.6.1.5	InterfaceIndex	read-create	This MIB object specifies an interface over which the controller is reachable.
INE hpicfOpenFlowControllerPort	1.3.6.1.4.1.11.2.14.11.5.1.89.1.6.1.4	InetPortNumber	read-create	The port over which the controller can be reached.
ROW hpicfOpenFlowControllerRowStatus	1.3.6.1.4.1.11.2.14.11.5.1.89.1.6.1.6	RowStatus	read-create	Row status for this table. The hpicfOpenFlowControllerInetAddress and hpicfOpenFlowControllerInterface MIB objects have to be set to valid values to move this object to 'active' state. This conceptual row can be deleted only if the corresponding controller association is removed from the hpicfOpenFlowInstanceControllerTable.
IP hpicfOpenFlowControllerSourceAddress	1.3.6.1.4.1.11.2.14.11.5.1.89.1.6.1.8	InetAddress	read-create	Source IP address to use when connecting to the controller.
IPt hpicfOpenFlowControllerSourceAddressType	1.3.6.1.4.1.11.2.14.11.5.1.89.1.6.1.7	InetAddressType	read-create	Address type of the Source IP. This implementation supports only ipv4 type.
hpicfOpenFlowControllerTable	1.3.6.1.4.1.11.2.14.11.5.1.89.1.6		not-accessible	Table used to configure controllers. For maximum number of OpenFlow controllers that can be supported, refer to hpicfOpenFlowMaxControllers MIB object.
INT hpicfOpenFlowEgressOnlyPorts	1.3.6.1.4.1.11.2.14.11.5.1.89.1.21.10	INTEGER	read-write	Setting this MIB object to 'enable' will advertise egress-only ports to the controller.
hpicfOpenFlowGlobalConfigGroup	1.3.6.1.4.1.11.2.14.11.5.1.89.2.2.1			Controls the global configuration of OpenFlow status and allocation of policy engine resource.
hpicfOpenFlowGroups	1.3.6.1.4.1.11.2.14.11.5.1.89.2.2
INT hpicfOpenFlowInstanceAdminStatus	1.3.6.1.4.1.11.2.14.11.5.1.89.1.4.1.2	INTEGER	read-create	This object is used to administratively enable or disable an OpenFlow instance. This MIB object can be set to 'enable' only when either hpicfOpenFlowInstanceListenPortCfg has been set to 'true' or atleast one controller is associated with this instance.
BIT hpicfOpenFlowInstanceCapabilities	1.3.6.1.4.1.11.2.14.11.5.1.89.1.4.1.23	Bits	read-only	This MIB object specifies the instance capabilities exchanged with the controller.
T/F hpicfOpenFlowInstanceControllerConnSecure	1.3.6.1.4.1.11.2.14.11.5.1.89.1.8.1.4	TruthValue	read-create	This object indicates if the connection between the controller and instance is secure. Setting this MIB to true will initiate TLS as transport protocol.
hpicfOpenFlowInstanceControllerEntry	1.3.6.1.4.1.11.2.14.11.5.1.89.1.8.1		not-accessible	A set of objects used to monitor the status and state of connection between an OpenFlow instance and controller.
hpicfOpenFlowInstanceControllerGroup	1.3.6.1.4.1.11.2.14.11.5.1.89.2.2.6			A set of objects used to monitor the status and state of an OpenFlow Instance and controller connection.
INT hpicfOpenFlowInstanceControllerRole	1.3.6.1.4.1.11.2.14.11.5.1.89.1.8.1.3	INTEGER	read-only	Role of a controller in an instance. The default role of a controller is equal. In this role, the controller has full access to the switch and is equal to other controllers in the same role. In slave role, the controller has read-only access to the switch. The master role is similar to equal and has full access to the switch, the difference is that the switch ensures it is the only controller in this role. When a controller changes its role to master, the switch changes all other controllers with the role master to have the role slave.
ROW hpicfOpenFlowInstanceControllerRowStatus	1.3.6.1.4.1.11.2.14.11.5.1.89.1.8.1.5	RowStatus	read-create	Row status for this table. Row transition to 'createAndWait', 'notReady' and 'notInService' states are not allowed.
INT hpicfOpenFlowInstanceControllerState	1.3.6.1.4.1.11.2.14.11.5.1.89.1.8.1.2	INTEGER	read-only	Connection state between an OpenFlow instance and a controller. The state 'void' implies that there is no connection. The state 'backoff' represents a state where the device is attempting to reconnect to the controller at increasing intervals of time. The state 'connecting' represents a state where the device is in the process of connecting to the controller. The state 'active' implies that a connection has been established and that the controller is responsive. The state 'idle' implies that the connection is idle and waiting for a response.
INT hpicfOpenFlowInstanceControllerStatus	1.3.6.1.4.1.11.2.14.11.5.1.89.1.8.1.1	INTEGER	read-only	Connection status between an OpenFlow instance and a controller.
hpicfOpenFlowInstanceControllerTable	1.3.6.1.4.1.11.2.14.11.5.1.89.1.8		not-accessible	Table that contains objects for connection state and status between an OpenFlow instance and a controller.
STR hpicfOpenFlowInstanceDatapathDesc	1.3.6.1.4.1.11.2.14.11.5.1.89.1.4.1.28	DisplayString	read-write	This MIB object is a user-defined description of the data path. If not set, hpicfOpenFlowInstanceName is used.
C64 hpicfOpenFlowInstanceDatapathID	1.3.6.1.4.1.11.2.14.11.5.1.89.1.4.1.11	Counter64	read-only	Datapath ID(DPID) uniquely identifies a datapath between this instance and the controller. Its lower 48-bits are intended for switch MAC address, while the upper 16-bits are defined by the implementation.
INT hpicfOpenFlowInstanceDestMacGrpTable	1.3.6.1.4.1.11.2.14.11.5.1.89.1.4.1.30	INTEGER	read-create	This object is used to enable or disable the destination MAC group table in the OpenFlow table. This MIB object can be set to 'enable' only on one instance.
POR hpicfOpenFlowInstanceEgressOnlyPorts	1.3.6.1.4.1.11.2.14.11.5.1.89.1.4.1.22	PortList	read-only	This MIB object specifies the list of egress only ports for this OpenFlow instance.
hpicfOpenFlowInstanceEntry	1.3.6.1.4.1.11.2.14.11.5.1.89.1.4.1		not-accessible	A set of objects that are used to create an OpenFlow instance.
INT hpicfOpenFlowInstanceFlowLocationMode	1.3.6.1.4.1.11.2.14.11.5.1.89.1.4.1.7	INTEGER	read-create	This object specifies if the flows for this instance will be located in hardware only or in hardware and software. By default, flows will be located in hardware and software.This object is applicable only for an OpenFlow version 1.0 instance.
hpicfOpenFlowInstanceGroup	1.3.6.1.4.1.11.2.14.11.5.1.89.2.2.2			A collection of objects used to define an OpenFlow instance.
hpicfOpenFlowInstanceGroup1	1.3.6.1.4.1.11.2.14.11.5.1.89.2.2.16			A collection of objects used to define an OpenFlow instance.
hpicfOpenFlowInstanceGroup2	1.3.6.1.4.1.11.2.14.11.5.1.89.2.2.20			A collection of objects used to define an OpenFlow instance.
hpicfOpenFlowInstanceGroup3	1.3.6.1.4.1.11.2.14.11.5.1.89.2.2.21			A collection of objects used to define an OpenFlow instance.
I32 hpicfOpenFlowInstanceHwRateLimit	1.3.6.1.4.1.11.2.14.11.5.1.89.1.4.1.9	Integer32	read-create	This object limits the bandwidth per module in kilobits per second, that this OpenFlow instance can utilize. This implementation supports a minimum rate limit of 0 kbps and a maximum rate limit of 10000000 kbps.
C64 hpicfOpenFlowInstanceHwTableMissCount	1.3.6.1.4.1.11.2.14.11.5.1.89.1.4.1.24	Counter64	read-only	This MIB object specifies the number of packets which do not match any rules in the hardware table. This object is applicable only for an OpenFlow version 1.0 instance.
INE hpicfOpenFlowInstanceListenPort	1.3.6.1.4.1.11.2.14.11.5.1.89.1.4.1.4	InetPortNumber	read-create	Port number for the listen-port on the OpenFlow instance. A valid port number is between 1024 and 65534 inclusive.
T/F hpicfOpenFlowInstanceListenPortCfg	1.3.6.1.4.1.11.2.14.11.5.1.89.1.4.1.3	TruthValue	read-create	This object indicates if a listen-port is configured on this OpenFlow instance.
T/F hpicfOpenFlowInstanceListenPortIsOobm	1.3.6.1.4.1.11.2.14.11.5.1.89.1.4.1.5	TruthValue	read-create	This object indicates if a listen-port is configured for this OpenFlow instance over OOBM(Out Of Band Management) interface. This MIB object will be applicable only if there is a physical OOBM port on the device.
U32 hpicfOpenFlowInstanceMaxBackOffInterval	1.3.6.1.4.1.11.2.14.11.5.1.89.1.4.1.15	Unsigned32	read-create	Interval between two consecutive attempts made by an instance to reconnect to a controller increases exponentially till it reaches the value specified by this MIB object. All subsequent attempts use this value as the interval between retries.
VID hpicfOpenFlowInstanceMembers	1.3.6.1.4.1.11.2.14.11.5.1.89.1.4.1.26	VidList	read-write	This MIB object is used to add member VLANs to an OpenFlow instance.
hpicfOpenFlowInstanceMembershipEntry	1.3.6.1.4.1.11.2.14.11.5.1.89.1.5.1		not-accessible	A set of objects that are used to add members to an OpenFlow instance.
hpicfOpenFlowInstanceMembershipGroup	1.3.6.1.4.1.11.2.14.11.5.1.89.2.2.3			An object used to associate a member to an OpenFlow instance.
ROW hpicfOpenFlowInstanceMembershipRowStatus	1.3.6.1.4.1.11.2.14.11.5.1.89.1.5.1.2	RowStatus	read-create	Row status for this member.
hpicfOpenFlowInstanceMembershipTable	1.3.6.1.4.1.11.2.14.11.5.1.89.1.5		not-accessible	Table used to add members to OpenFlow instances. This table is deprecated and instead object hpicfOpenFlowInstanceMembers is used to configure members for an OpenFlow instance.
hpicfOpenFlowInstanceMeterBandEntry	1.3.6.1.4.1.11.2.14.11.5.1.89.1.20.1		not-accessible	A set of objects used to retrieve details about meter bands associated with a meter and an OpenFlow instance.
hpicfOpenFlowInstanceMeterBandGroup	1.3.6.1.4.1.11.2.14.11.5.1.89.2.2.14			A collection of objects used to retrieve details about meter band types.
U32 hpicfOpenFlowInstanceMeterBandID	1.3.6.1.4.1.11.2.14.11.5.1.89.1.20.1.1	Unsigned32	not-accessible	Unique ID given to a band in a meter.
U32 hpicfOpenFlowInstanceMeterBandRate	1.3.6.1.4.1.11.2.14.11.5.1.89.1.20.1.3	Unsigned32	read-only	This MIB object specifies the rate beyond which the incoming packets would be treated according to action specified by hpicfOpenFlowInstanceMeterBandType MIB. The units of this rate is determined by the hpicfOpenFlowInstanceMeterBandRateUnit MIB
INT hpicfOpenFlowInstanceMeterBandRateUnit	1.3.6.1.4.1.11.2.14.11.5.1.89.1.20.1.4	INTEGER	read-only	This MIB object specifies the unit for hpicfOpenFlowInstanceMeterBandRate MIB. The units can be either kilobits per second or packets per second.
hpicfOpenFlowInstanceMeterBandTable	1.3.6.1.4.1.11.2.14.11.5.1.89.1.20		not-accessible	Table that contains objects related to meter bands for a specific meter in an OpenFlow instance. This table is populated when meters and their bands are configured from controller.
INT hpicfOpenFlowInstanceMeterBandType	1.3.6.1.4.1.11.2.14.11.5.1.89.1.20.1.2	INTEGER	read-only	This meter band type determines how the packets are processed.
U32 hpicfOpenFlowInstanceMeterDuration	1.3.6.1.4.1.11.2.14.11.5.1.89.1.19.1.5	Unsigned32	read-only	Duration for which this meter is active.
hpicfOpenFlowInstanceMeterEntry	1.3.6.1.4.1.11.2.14.11.5.1.89.1.19.1		not-accessible	A set of objects used to retrieve details about meters associated with an OpenFlow instance.
U32 hpicfOpenFlowInstanceMeterFlowCount	1.3.6.1.4.1.11.2.14.11.5.1.89.1.19.1.2	Unsigned32	read-only	Number of flows on which this meter is applied.
hpicfOpenFlowInstanceMeterGroup	1.3.6.1.4.1.11.2.14.11.5.1.89.2.2.13			A collection of objects used to retrieve details about instance-specific meters.
U32 hpicfOpenFlowInstanceMeterID	1.3.6.1.4.1.11.2.14.11.5.1.89.1.19.1.1	Unsigned32	not-accessible	Unique ID given to a meter.
C64 hpicfOpenFlowInstanceMeterInBandByteCount	1.3.6.1.4.1.11.2.14.11.5.1.89.1.20.1.6	Counter64	read-only	Number of bytes processed by this meter.
C64 hpicfOpenFlowInstanceMeterInBandPktCount	1.3.6.1.4.1.11.2.14.11.5.1.89.1.20.1.5	Counter64	read-only	Number of packets processed by this meter.
C64 hpicfOpenFlowInstanceMeterInputByteCount	1.3.6.1.4.1.11.2.14.11.5.1.89.1.19.1.4	Counter64	read-only	Number of bytes processed by this meter.
C64 hpicfOpenFlowInstanceMeterInputPktCount	1.3.6.1.4.1.11.2.14.11.5.1.89.1.19.1.3	Counter64	read-only	Number of packets processed by this meter.
U32 hpicfOpenFlowInstanceMeterPrecedenceLevel	1.3.6.1.4.1.11.2.14.11.5.1.89.1.20.1.7	Unsigned32	read-only	DSCP Precedence level of the band in a meter.
hpicfOpenFlowInstanceMeterTable	1.3.6.1.4.1.11.2.14.11.5.1.89.1.19		not-accessible	Table that contains objects related to meters of an OpenFlow instance. This table is populated when meters are configured from controller.
INT hpicfOpenFlowInstanceMissRuleDefaultAction	1.3.6.1.4.1.11.2.14.11.5.1.89.1.4.1.31	INTEGER	read-write	This MIB object is used to configure the flow miss action associated with the instance. A value of 0(none) indicates no flow miss action specified, which is to drop all unknown packets. A value of 1(drop) enables an instance to drop all unknown packets. A value of 2(normal) enables an instance to forward all unknown packets using non-OpenFlow pipeline. A value of 3(ctrl) enables an instance to forward all unknown packets to the OpenFlow controller.
INT hpicfOpenFlowInstanceMode	1.3.6.1.4.1.11.2.14.11.5.1.89.1.4.1.6	INTEGER	read-create	This object allows the user to specify the mode of OpenFlow operation for an instance. In active mode, new flows get redirected to the OpenFlow controller. In passive mode, new flows are not sent to the OpenFlow controller.This object is applicable only for an OpenFlow version 1.0 instance.
STR hpicfOpenFlowInstanceName	1.3.6.1.4.1.11.2.14.11.5.1.89.1.4.1.1	SnmpAdminString	not-accessible	Unique name given to an OpenFlow instance. The instance name 'aggregate' is special case denoting switch functioning as OpenFlow switch. The instance name allows lowercase alphanumeric characters and the special character underscore.
C64 hpicfOpenFlowInstanceNumOfHwFlowsEx	1.3.6.1.4.1.11.2.14.11.5.1.89.1.4.1.12	Counter64	read-only	This object indicates the number of hardware flows in this OpenFlow instance.
C64 hpicfOpenFlowInstanceNumOfSwFlows	1.3.6.1.4.1.11.2.14.11.5.1.89.1.4.1.13	Counter64	read-only	This object indicates the number of software flows in this OpenFlow instance.
U32 hpicfOpenFlowInstanceNumOfSwFlowTable	1.3.6.1.4.1.11.2.14.11.5.1.89.1.4.1.20	Unsigned32	read-create	This MIB object specifies the number of software flow tables for this OpenFlow instance. The maximum value supported is 8. This object is applicable only for an OpenFlow version 1.3 instance.
INT hpicfOpenFlowInstanceOperStatus	1.3.6.1.4.1.11.2.14.11.5.1.89.1.4.1.14	INTEGER	read-only	This object is used to determine the operational state of an OpenFlow instance. The reason for operational status to be down is specified by the hpicfOpenFlowInstanceOperStatusReason MIB.
INT hpicfOpenFlowInstanceOperStatusReason	1.3.6.1.4.1.11.2.14.11.5.1.89.1.4.1.21	INTEGER	read-only	This MIB object specifies the reason for hpicfOpenFlowInstanceOperStatus to be down.
BIT hpicfOpenFlowInstanceOverrideProtocol	1.3.6.1.4.1.11.2.14.11.5.1.89.1.4.1.32	Bits	read-write	This MIB object is used to configure the Override protocol associated with the instance.
INT hpicfOpenFlowInstancePipelineModel	1.3.6.1.4.1.11.2.14.11.5.1.89.1.4.1.27	INTEGER	read-write	This MIB object is used to configure the openflow instance pipeline model. A value of 0(none) indicates no table pipeline model which is equal to standard match. A value of 1(standardMatch) enables an instance in advertising its policy-engine and software tables. A value of 2(ipControlTable) enables an OpenFlow 1.3 instance in advertising its IP control table. A value of 3(customPipeline) enables an OpenFlow controller to create a custom OpenFlow table pipeline in the OpenFlow 1.3 instance.
INT hpicfOpenFlowInstancePktInVlanTagging	1.3.6.1.4.1.11.2.14.11.5.1.89.1.4.1.33	INTEGER	read-write	This MIB object is used to configure the 802.1q tagging property for a packet encapsulated inside the OpenFlow packet-in header. A value of 0 (default) indicates the default behavior which is the packet encapsulated inside a packet-in message will be tagged in the following cases a) the instance type is aggregate. b) the instance is a named instance with more than one member VLAN. c) the instance is a named instance and the packet was received with a tag. It will be untagged in all other cases. A value of 1 (inputForm) directs the instance to send the encapsulated packet as it was received on the physical port. A value of 2 (tagAlways) directs the instance to send the encapsulated packet always with an 802.1q tag irrespective of how it was received on the physical port. A value of 3 (untagAlways) directs the instance to send the encapsulated packet always without an 802.1q tag irrespective of how it was received on the physical port.
U32 hpicfOpenFlowInstanceProbeInterval	1.3.6.1.4.1.11.2.14.11.5.1.89.1.4.1.17	Unsigned32	read-create	This MIB object specifies the interval between two consecutive probes sent from an instance to the controller. This MIB value also determines how soon the instance will enter the connection interruption mode. If the instance does not hear a reply from the controller for three consecutive probes, it will flag the controller as unreachable and enter connection interruption mode.
INT hpicfOpenFlowInstanceProtoVersion	1.3.6.1.4.1.11.2.14.11.5.1.89.1.4.1.18	INTEGER	read-create	This MIB object specifies the OpenFlow instance protocol version.
T/F hpicfOpenFlowInstanceProtoVersionOnly	1.3.6.1.4.1.11.2.14.11.5.1.89.1.4.1.19	TruthValue	read-create	Setting this MIB object to true will support only the specific version mentioned by hpicfOpenFlowInstanceProtoVersion MIB and not compatible with lower versions.
ROW hpicfOpenFlowInstanceRowStatus	1.3.6.1.4.1.11.2.14.11.5.1.89.1.4.1.16	RowStatus	read-create	Row status for this table.
INT hpicfOpenFlowInstanceSourceMacGrpTable	1.3.6.1.4.1.11.2.14.11.5.1.89.1.4.1.29	INTEGER	read-create	This object is used to enable or disable the source MAC group table in the OpenFlow pipeline. This MIB object can be set to 'enable' only on one instance.
I32 hpicfOpenFlowInstanceSwRateLimit	1.3.6.1.4.1.11.2.14.11.5.1.89.1.4.1.10	Integer32	read-create	This object limits the number of packets per second for each module, that this instance can send to the software path on the CPU. Increasing the software rate limit would increase CPU consumption and may impact the system performance. For maximum number of packets per second for each module, that an OpenFlow instance can send to the software path on the CPU, refer to hpicfOpenFLowInstanceMaxSwRateLimit MIB object.
hpicfOpenFlowInstanceTable	1.3.6.1.4.1.11.2.14.11.5.1.89.1.4		not-accessible	A table that is used create an OpenFlow instance. For maximum number of OpenFlow instances that can be supported, refer to hpicfOpenFLowMaxInstances MIB object.
INT hpicfOpenFlowInstanceTableModel	1.3.6.1.4.1.11.2.14.11.5.1.89.1.4.1.25	INTEGER	read-only	This MIB object determines the table model of an OpenFlow instance.
INT hpicfOpenFlowIpControlTableMode	1.3.6.1.4.1.11.2.14.11.5.1.89.1.21.9	INTEGER	read-write	This MIB object specifies the OpenFlow operation mode. In this mode, IP control table would be advertised by an OpenFlow 1.3 instance.
U32 hpicfOpenFlowIPControlTableStatsRefreshRate	1.3.6.1.4.1.11.2.14.11.5.1.89.1.21.2	Unsigned32	read-only	This MIB object is used to specify the time interval at which the hardware will be polled for statistics. A value of '0' would mean that the hardware will no longer be polled to update the statistics.
U32 hpicfOpenFlowIPControlTableUsage	1.3.6.1.4.1.11.2.14.11.5.1.89.1.21.1	Unsigned32	read-write	This object is used to specify maximum percentage of IP control table resources that can be used by OpenFlow. The percentage is not a guarantee, but a maximum allowed limit.
I32 hpicfOpenFlowMaxControllers	1.3.6.1.4.1.11.2.14.11.5.1.89.1.12	Integer32	read-only	This MIB object specifies the maximum number of OpenFlow controllers.
I32 hpicfOpenFlowMaxFlows	1.3.6.1.4.1.11.2.14.11.5.1.89.1.11	Integer32	read-only	This MIB objects specifies the total number of flows that can be supported on the switch. That is, the sum of all hardware flows and software flows across all OpenFlow instances cannot exceed this number.
I32 hpicfOpenFlowMaxInstances	1.3.6.1.4.1.11.2.14.11.5.1.89.1.10	Integer32	read-only	This MIB object specifies the maximum number of OpenFlow instances.
hpicfOpenFlowMIB	1.3.6.1.4.1.11.2.14.11.5.1.89			The MIB module for configuring OpenFlow.
hpicfOpenFlowNotifications	1.3.6.1.4.1.11.2.14.11.5.1.89.0
hpicfOpenFlowObjects	1.3.6.1.4.1.11.2.14.11.5.1.89.1
hpicfOpenFlowScalarObjects	1.3.6.1.4.1.11.2.14.11.5.1.89.1.21
hpicfOpenFlowScalarsGroup	1.3.6.1.4.1.11.2.14.11.5.1.89.2.2.15			Basic Scalars required for OpenFlow implementation.
hpicfOpenFlowScalarsGroup1	1.3.6.1.4.1.11.2.14.11.5.1.89.2.2.17			Basic Scalars required for OpenFlow implementation.
INT hpicfOpenFlowStatus	1.3.6.1.4.1.11.2.14.11.5.1.89.1.1	INTEGER	read-write	Global configuration to enable or disable OpenFlow on the device. The 'disableWithClearConfig' enum disables OpenFlow along with removing all the OpenFlow related configuration.

RFC description

Configures OpenFlow controllers and instances on HP networking switches, supporting software-defined networking capabilities.

Start monitoring HP ProCurve/HP Networking OpenFlow-enabled switch with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HP-ICF-OPENFLOW-MIB