All MIBs › HP-ICF-OSPF
Organization: HP Networking
Last Updated: 2017-05-18
Category: Protocol: OSPF, Routing Protocols, Technology: Routing/L3, Vendor: HP/HPE
Description: HP ICF SNMP MIB for OSPF routing protocol configuration and state on HP ProCurve Layer 3 switches.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is HP-ICF-OSPF?
HP-ICF-OSPF is an HP proprietary SNMP MIB that extends the standard OSPF-MIB with HP-specific objects for OSPF (Open Shortest Path First) routing protocol management on HP ProCurve Layer 3 switches. It provides additional configuration and operational-state data for OSPF areas, interfaces, and neighbors beyond what the IETF OSPF-MIB captures, supporting routing protocol administration on the device. For monitoring, this MIB is used to check the software/protocol status of the routing engine, such as OSPF adjacency and interface states, which reflect the health of the device's routing software rather than physical hardware sensors. Because it is explicitly built as an extension, it has a direct and notable dependency on the standard OSPF-MIB (RFC 4750/1850) for its base object definitions and indexing. It is typically deployed on HP ProCurve switches and routers acting as OSPF speakers within an enterprise or campus Layer 3 network. Engineers can download the HP-ICF-OSPF file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in HP-ICF-OSPF. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- HP ProCurve Layer 3 switch/router
Monitoring Examples
No sample objects were retrieved for this module, so specific table or object names cannot be confirmed from source, but as an OSPF-MIB extension it would be expected to add HP-specific columns onto or alongside standard tables such as ospfIfTable and ospfNbrTable. An administrator would typically poll OSPF neighbor and interface state together with any HP extension objects to confirm adjacencies remain full and interfaces are not flapping. Because it augments a well-known standard MIB, most day-to-day OSPF monitoring would actually be done through the base OSPF-MIB with this module supplying vendor-specific supplementary detail.
What Can Be Monitored
- OSPF interface state (HP extensions)
- OSPF neighbor/adjacency state
- OSPF area configuration extensions
This MIB depends on
Related MIBs
Imported Objects
From HP-ICF-OID
| hpSwitch | OBJECT-IDENTITY |
From IANA-RTPROTO-MIB
| IANAipRouteProtocol |
From IF-MIB
| InterfaceIndex |
From OSPF-MIB
| AreaID | |
| BigMetric | |
| Metric | |
| PositiveInteger | |
| ospfAddressLessIf | |
| ospfAreaAggregateEntry | |
| ospfExtLsdbEntry | |
| ospfIfEntry | |
| ospfIfIpAddress | |
| ospfIfMetricEntry | |
| ospfLsdbAreaId | |
| ospfLsdbEntry | |
| ospfLsdbLsid | |
| ospfLsdbRouterId | |
| ospfLsdbType | |
| ospfNbrEntry |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| DisplayString | |
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TruthValue |
How to Use in IPNetwork Monitor
Example using hpicfOspfSentHelloPkt OID:
Select an HP ProCurve Layer 3 switch/router (OSPF extensions) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type hpicfOspfSentHelloPkt into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The number of OSPF Hello packets sent on the interface. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| hpicfOspf | 1.3.6.1.4.1.11.2.14.11.5.1.14 | This MIB module contains HP proprietary extensions to the OSPF-MIB module. | ||
| T/F hpicfOspf1583CompatibilityMode | 1.3.6.1.4.1.11.2.14.11.5.1.14.1.1.1 | TruthValue | read-write | Controls the preference rules used when choosing among multiple AS-external-LSAs advertising the same destination. When set to 'true', the preference rules remain those specified in RFC 1583. When set to 'false', the preference rules are those stated in RFC 2328, which prevent routing loops when AS-external-LSAs for the same destination have been originated from different areas. Set to 'true' by default. In order to minimize the chance of routing loops, all OSPF routers in an OSPF routing domain should have this object set identically. When there are routers present that have not been updated with the functionality specified in RFC 2328, all routers should have this object set to 'true'. Otherwise, all routers should have this object set to 'false', preventing all routing loops. |
| hpicfOspfAreaAggregateCompliance | 1.3.6.1.4.1.11.2.14.11.5.1.14.2.2.7 | The compliance statement for this module. | ||
| BIG hpicfOspfAreaAggregateCost | 1.3.6.1.4.1.11.2.14.11.5.1.14.1.6.1.1 | BigMetric | read-create | Manually configured cost of the summary advertisement. A value of 0 indicates that the cost defined and calculated by the OSPF standard should be used. Valid costs range from 1-16777215 |
| hpicfOspfAreaAggregateEntry | 1.3.6.1.4.1.11.2.14.11.5.1.14.1.6.1 | not-accessible | Each entry is extension of ospfAreaAggregateEntry | |
| hpicfOspfAreaAggregateGroup | 1.3.6.1.4.1.11.2.14.11.5.1.14.2.1.11 | Group for ospfAreaAggregate objects. | ||
| hpicfOspfAreaAggregateGroup1 | 1.3.6.1.4.1.11.2.14.11.5.1.14.2.1.13 | Group for ospfAreaAggregateType objects. | ||
| hpicfOspfAreaAggregateTable | 1.3.6.1.4.1.11.2.14.11.5.1.14.1.6 | not-accessible | HP proprietary extensions to ospfAreaAggregateTable | |
| INT hpicfOspfAreaAggregateType | 1.3.6.1.4.1.11.2.14.11.5.1.14.1.6.1.2 | INTEGER | read-create | Configure whether external metric and OSPF metric are comparable. If 'metric-type' is specified as 'type1', the external metric and the OSPF metric are considered comparable. 'type2' implies non-comparable metric |
| U32 hpicfOspfAreaLsdbAddrPrefix | 1.3.6.1.4.1.11.2.14.11.5.1.14.14.1.4 | Unsigned32 | read-only | The Prefix the Address. |
| hpicfOspfAreaLsdbEntry | 1.3.6.1.4.1.11.2.14.11.5.1.14.14.1 | not-accessible | A single Area-Scope Link State Advertisement. | |
| U32 hpicfOspfAreaLsdbExtRouteTags | 1.3.6.1.4.1.11.2.14.11.5.1.14.14.1.6 | Unsigned32 | read-only | This field is valid if the LSA is a NSSA LSA. This field is present only if the 'T' Bit is set in the EFT flags field. A 32-bit field which may be used to communicate additional information between AS boundary routers. |
| HPI hpicfOspfAreaLsdbFwdingAddress | 1.3.6.1.4.1.11.2.14.11.5.1.14.14.1.5 | HpicfOspfRouterIdTc | read-only | This field is valid if the LSA is a NSSA LSA. This field is present only if the 'F' Bit is set in the EFT flags field and if included, the data traffic for the advertised destination will be forwarded to this address. |
| hpicfOspfAreaLsdbGroup | 1.3.6.1.4.1.11.2.14.11.5.1.14.2.1.9 | These objects used for managing/monitoring OSPFv2 LSAs. | ||
| MET hpicfOspfAreaLsdbMetric | 1.3.6.1.4.1.11.2.14.11.5.1.14.14.1.3 | Metric | read-only | This field is valid if the LSA is a Router LSA, a Summary LSA, AS Summary LSA or a NSSA LSA. This field indicates the cost involved in using the interface or route. |
| U32 hpicfOspfAreaLsdbOptions | 1.3.6.1.4.1.11.2.14.11.5.1.14.14.1.2 | Unsigned32 | read-only | The Options field enables OSPF routers to support (or not support) optional capabilities, and to communicate their capability level to other OSPF routers. This field is valid for each type of LSA. |
| U32 hpicfOspfAreaLsdbRtrCapBits | 1.3.6.1.4.1.11.2.14.11.5.1.14.14.1.1 | Unsigned32 | read-only | This field is valid if the LSA is a Router LSA. It uniquely identifies the router type of the router in the Area. |
| hpicfOspfAreaLsdbTable | 1.3.6.1.4.1.11.2.14.11.5.1.14.14 | not-accessible | The OSPF Process's Area-Scope LSDB. The LSDB contains the Area-Scope Link State Advertisements from throughout the area that the device is attached to. | |
| hpicfOspfBaseGroup | 1.3.6.1.4.1.11.2.14.11.5.1.14.2.1.1 | Basic OSPF configuration information that is not in the standard OSPF MIB. | ||
| T/F hpicfOspfClearCounters | 1.3.6.1.4.1.11.2.14.11.5.1.14.7.1.1 | TruthValue | read-write | Read of this will always be false, When this variable is set to true for a given Ipaddress interface, corresponding interface counters will be cleared. |
| hpicfOspfCompliance | 1.3.6.1.4.1.11.2.14.11.5.1.14.2.2.1 | The compliance statement for HP Routing Switches that support OSPF. | ||
| hpicfOspfCompliance1 | 1.3.6.1.4.1.11.2.14.11.5.1.14.2.2.5 | The compliance statement for this module. | ||
| hpicfOspfCompliance2 | 1.3.6.1.4.1.11.2.14.11.5.1.14.2.2.8 | The compliance statement for this module. | ||
| hpicfOspfCompliance3 | 1.3.6.1.4.1.11.2.14.11.5.1.14.2.2.9 | The compliance statement for this module. | ||
| hpicfOspfCompliances | 1.3.6.1.4.1.11.2.14.11.5.1.14.2.2 | |||
| hpicfOspfConformance | 1.3.6.1.4.1.11.2.14.11.5.1.14.2 | |||
| BIG hpicfOspfDefaultImportMetric | 1.3.6.1.4.1.11.2.14.11.5.1.14.1.1.2 | BigMetric | read-write | The default metric used for advertising external routes imported into OSPF by this router. |
| INT hpicfOspfDefaultImportMetricType | 1.3.6.1.4.1.11.2.14.11.5.1.14.1.1.3 | INTEGER | read-write | The default metric type used for advertising external routes imported into OSPF by this router. |
| hpicfOspfDistanceGroup | 1.3.6.1.4.1.11.2.14.11.5.1.14.2.1.3 | A collection of objects for configuring the administrative distance of routes learned by OSPF. | ||
| I32 hpicfOspfExternalDistance | 1.3.6.1.4.1.11.2.14.11.5.1.14.1.1.6 | Integer32 | read-write | The default administrative distance to associate with AS-external routes learned by OSPF. Routes with lower distances are preferred. By default, OSPF routes have an administrative distance of 110. Note that the administrative distance settings for OSPF do not affect the choice of routes within OSPF. OSPF will still prefer intra-area routes and inter-area routes over AS-external routes even if hpicfOspfExternalDistance is lower than the hpicfOspfIntraAreaDistance or hpicfOspfInterAreaDistance. The appropriate administrative distance value is applied to the route that OSPF selects as its best route to a destination and is used to decide whether OSPF's route is preferred over a route from some other source. |
| U32 hpicfOspfExtLsdbBitE | 1.3.6.1.4.1.11.2.14.11.5.1.14.17.1.5 | Unsigned32 | read-only | The type of External metric. If bit E is set, the metric specified is Type 2 external metric. |
| hpicfOspfExtLsdbEntry | 1.3.6.1.4.1.11.2.14.11.5.1.14.17.1 | not-accessible | A single AS-Scope Link State Advertisement. | |
| U32 hpicfOspfExtLsdbExtRouteTags | 1.3.6.1.4.1.11.2.14.11.5.1.14.17.1.4 | Unsigned32 | read-only | The 32-bit Router Tags for the advertised Route. |
| HPI hpicfOspfExtLsdbFwdingAddress | 1.3.6.1.4.1.11.2.14.11.5.1.14.17.1.3 | HpicfOspfRouterIdTc | read-only | If included, Data traffic for the advertised destination will be forwarded to this address. |
| hpicfOspfExtLsdbGroup | 1.3.6.1.4.1.11.2.14.11.5.1.14.2.1.10 | These objects are used for OSPFv2 systems that display their AS-scope link state database. | ||
| U32 hpicfOspfExtLsdbMetric | 1.3.6.1.4.1.11.2.14.11.5.1.14.17.1.1 | Unsigned32 | read-only | The cost associated with this route. |
| U32 hpicfOspfExtLsdbOptions | 1.3.6.1.4.1.11.2.14.11.5.1.14.17.1.2 | Unsigned32 | read-only | The Options field enables OSPF routers to support (or not support) optional capabilities, and to communicate their capability level to other OSPF routers. |
| hpicfOspfExtLsdbTable | 1.3.6.1.4.1.11.2.14.11.5.1.14.17 | not-accessible | The OSPFv3 Process's AS-Scope Link State Database (LSDB). The LSDB contains the AS-Scope Link State Advertisements from throughout the areas that the device is attached to. | |
| I32 hpicfOspfFloodAge | 1.3.6.1.4.1.11.2.14.11.5.1.14.11.1.5 | Integer32 | read-only | This flood list field is the age of the link state advertisement in seconds. |
| I32 hpicfOspfFloodChecksum | 1.3.6.1.4.1.11.2.14.11.5.1.14.11.1.6 | Integer32 | read-only | This flood list field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagram's; it is commonly referred to as the Fletcher checksum. |
| hpicfOspfFloodCompliance | 1.3.6.1.4.1.11.2.14.11.5.1.14.2.2.3 | The compliance statement for show Floodlist command. | ||
| hpicfOspfFloodEntry | 1.3.6.1.4.1.11.2.14.11.5.1.14.11.1 | not-accessible | A Flood list information maintained for an OSPF Interface | |
| hpicfOspfFloodGroup | 1.3.6.1.4.1.11.2.14.11.5.1.14.2.5.2 | This is a normal group that gives checksum,sequence and age related information | ||
| hpicfOspfFloodGroups | 1.3.6.1.4.1.11.2.14.11.5.1.14.2.5 | |||
| IP hpicfOspfFloodLsid | 1.3.6.1.4.1.11.2.14.11.5.1.14.11.1.2 | IpAddress | read-only | The flood list Link State ID is an LS Type Specific field containing either a Router ID or an IP address; it identifies the piece of the routing domain that is being described by the advertisement. |
| hpicfOspfFloodManGroup | 1.3.6.1.4.1.11.2.14.11.5.1.14.2.5.1 | A mandatory group that displays ID information with Respect to Link state, router, `interface and the LSA type | ||
| IP hpicfOspfFloodRouterId | 1.3.6.1.4.1.11.2.14.11.5.1.14.11.1.3 | IpAddress | read-only | The 32-bit number that uniquely identifies the originating flood list router in the Autonomous System. |
| I32 hpicfOspfFloodSequence | 1.3.6.1.4.1.11.2.14.11.5.1.14.11.1.4 | Integer32 | read-only | The flood list sequence number field is a signed 32-bit integer. It starts with the value '80000001'h, or -'7FFFFFFF'h, and increments until '7FFFFFFF'h. Thus, a typical sequence number will be very negative. It is used to detect old and duplicate Link State Advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number, the more recent the advertisement. |
| hpicfOspfFloodTable | 1.3.6.1.4.1.11.2.14.11.5.1.14.11 | not-accessible | Flood list table that contains Ospf Interface Specific information | |
| INT hpicfOspfFloodType | 1.3.6.1.4.1.11.2.14.11.5.1.14.11.1.1 | INTEGER | read-only | The flood list LSA type .Each link state type has a separate advertisement format. |
| hpicfOspfGeneral | 1.3.6.1.4.1.11.2.14.11.5.1.14.1.1 | |||
| hpicfOspfGroups | 1.3.6.1.4.1.11.2.14.11.5.1.14.2.1 | |||
| T/F hpicfOspfIfBfdEnbl | 1.3.6.1.4.1.11.2.14.11.5.1.14.4.1.3 | TruthValue | read-write | param to enable BFD under OSPF |
| hpicfOspfIfClearStatsEntry | 1.3.6.1.4.1.11.2.14.11.5.1.14.7.1 | not-accessible | A list used to clear statistics information maintained for an OSPF interface. | |
| hpicfOspfIfClearStatsTable | 1.3.6.1.4.1.11.2.14.11.5.1.14.7 | not-accessible | A list used to clear statistics information maintained for an OSPF interface. | |
| hpicfOspfIfEntry | 1.3.6.1.4.1.11.2.14.11.5.1.14.4.1 | not-accessible | A list of extensions to the information maintained for an OSPF interface. | |
| C32 hpicfOspfIfErrorCount | 1.3.6.1.4.1.11.2.14.11.5.1.14.6.1.2 | Counter32 | read-only | The hpicfOspfErrorCount is count of each type error packet received on an OSPF interface. Discontinuities in the value of this counter can occur at re-initialization of the management system. The counters can be cleared for any interface using clear ip ospf statistics command |
| hpicfOspfIfErrorEntry | 1.3.6.1.4.1.11.2.14.11.5.1.14.6.1 | not-accessible | A list of extensions to the information maintained for an OSPF interface. | |
| hpicfOspfIfErrorTable | 1.3.6.1.4.1.11.2.14.11.5.1.14.6 | not-accessible | Table that contains OSPF Interface traffic specific information. | |
| I32 hpicfOspfIfErrorType | 1.3.6.1.4.1.11.2.14.11.5.1.14.6.1.1 | Integer32 | not-accessible | The hpicfOspfIfErrorType refers to the type of errors in the OSPF packet received on any OSPF enabled interface. Errors could be Invalid RouterID/ AreaID Checksum error, OutOfbound Error ... |
| I32 hpicfOspfIfFlagValue | 1.3.6.1.4.1.11.2.14.11.5.1.14.18.1.1.1 | Integer32 | read-write | This flag is defined to know the type of OSPF cost configuration.. -1 : Default configuration. 0 : Manual configuration. 1 : Global configuration (value taken from global). |
| hpicfOspfIfGroup | 1.3.6.1.4.1.11.2.14.11.5.1.14.2.1.8 | These interface objects used for managing/monitoring OSPFv2 interfaces. | ||
| hpicfOspfIfMetricEntry | 1.3.6.1.4.1.11.2.14.11.5.1.14.18.1.1 | not-accessible | A list of extensions to the information maintained for an OSPF interface. | |
| hpicfOspfIfMetricObjects | 1.3.6.1.4.1.11.2.14.11.5.1.14.18 | |||
| hpicfOspfIfMetricTable | 1.3.6.1.4.1.11.2.14.11.5.1.14.18.1 | not-accessible | Extensions to the table that contains OSPF Metric specific information. | |
| U32 hpicfOspfIfNbrCount | 1.3.6.1.4.1.11.2.14.11.5.1.14.4.1.2 | Unsigned32 | read-only | This object specifies the number of OSPFv3 neighbors present in this interface. This counter should be incremented when a new neighbor is added in the network in which this interface is present. It should be decremented when a neighbor is disconnected. |
| T/F hpicfOspfIfPassive | 1.3.6.1.4.1.11.2.14.11.5.1.14.4.1.1 | TruthValue | read-write | The passive state configuration of the OSPF interface. In the passive mode no OSPF protocol messages are exchanged on this interface. true (1) - The interface is configured to work in Passive mode false (2) - The interface is configured to work in normal mode. This is the default configuration. Changing the value will cause OSPF to reset on this interface and make necessary adjustments to the link state database. All other operations are not defined and will not affect the state of the protocol. |
| hpicfOspfIfStatsEntry | 1.3.6.1.4.1.11.2.14.11.5.1.14.5.1 | not-accessible | A list of extensions to the information maintained for an OSPF interface. | |
| hpicfOspfIfStatsTable | 1.3.6.1.4.1.11.2.14.11.5.1.14.5 | not-accessible | Table that contains OSPF Interface traffic specific information. | |
| hpicfOspfIfTable | 1.3.6.1.4.1.11.2.14.11.5.1.14.4 | not-accessible | Extensions to the table that contains OSPF Interface specific information. | |
| I32 hpicfOspfInterAreaDistance | 1.3.6.1.4.1.11.2.14.11.5.1.14.1.1.5 | Integer32 | read-write | The default administrative distance to associate with inter-area routes learned by OSPF. Routes with lower distances are preferred. By default, OSPF routes have an administrative distance of 110. Note that the administrative distance settings for OSPF do not affect the choice of routes within OSPF. OSPF will still prefer intra-area routes over inter-area routes, even if hpicfOspfInterAreaDistance is lower than hpicfOspfIntraAreaDistance. It will also still prefer inter-area routes over AS-external routes even if hpicfOspfExternalDistance is lower than hpicfOspfInterAreaDistance. The appropriate administrative distance value is applied to the route that OSPF selects as its best route to a destination and is used to decide whether OSPF's route is preferred over a route from some other source. |
| I32 hpicfOspfIntraAreaDistance | 1.3.6.1.4.1.11.2.14.11.5.1.14.1.1.4 | Integer32 | read-write | The default administrative distance to associate with intra-area routes learned by OSPF. Routes with lower distances are preferred. By default, OSPF routes have an administrative distance of 110. Note that the administrative distance settings for OSPF do not affect the choice of routes within OSPF. OSPF will still prefer intra-area routes over inter-area or AS-external routes even if hpicfOspfInterAreaDistance or hpicfOspfExternalDistance is lower than hpicfOspfIntraAreaDistance. The appropriate administrative distance value is applied to the route that OSPF selects as its best route to a destination and is used to decide whether OSPF's route is preferred over a route from some other source. |
| HPI hpicfOspfLogAction | 1.3.6.1.4.1.11.2.14.11.5.1.14.1.4.1.2 | HpicfOspfLogAction | read-write | The action, if any, that was taken by the agent when the event represented by hpicfOspfLogType. When enabled, brief information of the event is logged and if it is set to enabledWithDetail, provides more information, like every state changes, will get logged. If it is set to disabled, no events are logged. |
| hpicfOspfLogEntry | 1.3.6.1.4.1.11.2.14.11.5.1.14.1.4.1 | not-accessible | The configuration parameters pertaining to a OSPF log entry. Each entry contains information about the action and severity for a particular logType, and for each version of OSPF. | |
| hpicfOspfLogGroup | 1.3.6.1.4.1.11.2.14.11.5.1.14.2.1.6 | A collection of objects for configuring the logging of OSPF events. | ||
| hpicfOspfLogTable | 1.3.6.1.4.1.11.2.14.11.5.1.14.1.4 | not-accessible | A table containing the configuration parameters pertaining for OSPF routing protocol logging facility. | |
| HPI hpicfOspfLogType | 1.3.6.1.4.1.11.2.14.11.5.1.14.1.4.1.1 | HpicfOspfLogType | not-accessible | The type of log for every kind of event in OSPF routing protocol . |
| U32 hpicfOspfLsdbBitE | 1.3.6.1.4.1.11.2.14.11.5.1.14.14.1.9 | Unsigned32 | read-only | The 32-bit identifier for the Metric specific information of the LSA. |
| U32 hpicfOspfLsdbRouterLinks | 1.3.6.1.4.1.11.2.14.11.5.1.14.14.1.8 | Unsigned32 | read-only | This field is valid if the LSA is Router LSA. It holds the information of Number of links in the router LSA. |
| hpicfOspfMetricGroup | 1.3.6.1.4.1.11.2.14.11.5.1.14.2.1.16 | Flags to identify global or manual OSPF cost configuration. | ||
| ARE hpicfOspfNbrAreaId | 1.3.6.1.4.1.11.2.14.11.5.1.14.1.5.1.5 | AreaID | read-only | A 32-bit integer uniquely identifying an area. Area ID 0.0.0.0 is used for the OSPF backbone. |
| IP hpicfOspfNbrBackupDesignatedRouter | 1.3.6.1.4.1.11.2.14.11.5.1.14.1.5.1.4 | IpAddress | read-only | The IP address of the backup designated router. |
| INT hpicfOspfNbrBfdState | 1.3.6.1.4.1.11.2.14.11.5.1.14.1.5.1.7 | INTEGER | read-only | The ifName value of this OSPF interface. |
| IP hpicfOspfNbrDesignatedRouter | 1.3.6.1.4.1.11.2.14.11.5.1.14.1.5.1.3 | IpAddress | read-only | The IP address of the designated router. |
| hpicfOspfNbrEntry | 1.3.6.1.4.1.11.2.14.11.5.1.14.1.5.1 | not-accessible | Each entry is extension of ospfNbr Entry and gives more information for OSPF neighbors | |
| hpicfOspfNbrGroup | 1.3.6.1.4.1.11.2.14.11.5.1.14.2.1.7 | A collection of read-only elements for an OSPF neighbor. | ||
| hpicfOspfNbrGroup1 | 1.3.6.1.4.1.11.2.14.11.5.1.14.2.1.14 | A collection of read-only elements for an OSPF neighbor. | ||
| STR hpicfOspfNbrInterfaceName | 1.3.6.1.4.1.11.2.14.11.5.1.14.1.5.1.6 | DisplayString | read-only | The ifName value of this OSPF interface. |
| hpicfOspfNbrTable | 1.3.6.1.4.1.11.2.14.11.5.1.14.1.5 | not-accessible | HP proprietary extension to ospfNbrTable to support read-only elements for reading neighbor adjacency length, designated router, backup designated router, Area ID and the and time-to-expiry for an OSPF neighbor | |
| NUM hpicfOspfNbrTimeToExpiry | 1.3.6.1.4.1.11.2.14.11.5.1.14.1.5.1.2 | PositiveInteger | read-only | This object specifies the time remaining for the dead timer for the particular neighbor to expire. This counter thus specifies the time in seconds left for an adjacency to be brought down in case no Hello packet is received during the interval. |
| NUM hpicfOspfNbrUpTime | 1.3.6.1.4.1.11.2.14.11.5.1.14.1.5.1.1 | PositiveInteger | read-only | This object specifies the time duration for which the adjacency with the particular neighbor is active. This should be a monotonically increasing timer for the duration the adjacency is active. This counter should be reset when an adjacency is lost or re-established. |
| HPI hpicfOspfNetworkLSAAttachedRouter | 1.3.6.1.4.1.11.2.14.11.5.1.14.16.1.2 | HpicfOspfRouterIdTc | read-only | The 32-bit Router identifier of the attached Router. |
| hpicfOspfNetworkLSAEntry | 1.3.6.1.4.1.11.2.14.11.5.1.14.16.1 | not-accessible | A single Area-Scope Link State Advertisement. | |
| U32 hpicfOspfNetworkLSASeqNum | 1.3.6.1.4.1.11.2.14.11.5.1.14.16.1.1 | Unsigned32 | not-accessible | The 32-bit sequence number identifying the attached router-ids. |
| hpicfOspfNetworkLSATable | 1.3.6.1.4.1.11.2.14.11.5.1.14.16 | not-accessible | This table having Area scope is a dependent-expansion table for the Network LSA entry in the Area LSDB table. This table represents the list of routers advertised in a Network LSA. | |
| hpicfOspfNssaType1 | 1.3.6.1.4.1.11.2.14.11.5.1.14.3.1 | |||
| hpicfOspfNssaType2 | 1.3.6.1.4.1.11.2.14.11.5.1.14.3.2 | |||
| hpicfOspfObjects | 1.3.6.1.4.1.11.2.14.11.5.1.14.1 | |||
| C32 hpicfOspfRcvdDDPkt | 1.3.6.1.4.1.11.2.14.11.5.1.14.5.1.7 | Counter32 | read-only | The number of Database Description packets received on the interface. This number is incremented each time a OSPF DD packet is received on OSPF enabled interface. Discontinuities in the value of this counter can occur at re-initialization of the management system. The counters can be cleared for any interface using clear ip ospf statistics command. |
| C32 hpicfOspfRcvdHelloPkt | 1.3.6.1.4.1.11.2.14.11.5.1.14.5.1.6 | Counter32 | read-only | The number of Hello packets received on the interface. This number is incremented each time a hello packet is received on OSPF enabled interface. Discontinuities in the value of this counter can occur at re-initialization of the management system. The counters can be cleared for any interface using clear ip ospf statistics command. |
| C32 hpicfOspfRcvdLSAPkt | 1.3.6.1.4.1.11.2.14.11.5.1.14.5.1.10 | Counter32 | read-only | The number of Link State Ack packets received on the interface. This number is incremented each time a OSPF LSA packet is received on OSPF enabled interface. Discontinuities in the value of this counter can occur at re-initialization of the management system. The counters can be cleared for any interface using clear ip ospf statistics command. |
| C32 hpicfOspfRcvdLSRPkt | 1.3.6.1.4.1.11.2.14.11.5.1.14.5.1.8 | Counter32 | read-only | The number of Link State Request packets received on the interface. This number is incremented each time a OSPF LSR packet is received on OSPF enabled interface. Discontinuities in the value of this counter can occur at re-initialization of the management system. The counters can be cleared for any interface using clear ip ospf statistics command. |
| C32 hpicfOspfRcvdLSUPkt | 1.3.6.1.4.1.11.2.14.11.5.1.14.5.1.9 | Counter32 | read-only | The number of Link State Update packets received on the interface. This number is incremented each time a OSPF LSU packet is received on OSPF enabled interface. |
| T/F hpicfOspfRedistEnabled | 1.3.6.1.4.1.11.2.14.11.5.1.14.1.2.1.2 | TruthValue | read-write | A flag indicating whether OSPF should redistribute routes from this source protocol. |
| hpicfOspfRedistEntry | 1.3.6.1.4.1.11.2.14.11.5.1.14.1.2.1 | not-accessible | An entry in the table for configuring route redistribution into OSPF from a single source protocol. Entries in this table are not created dynamically. There will be a single entry for each supported source protocol. | |
| hpicfOspfRedistGroup | 1.3.6.1.4.1.11.2.14.11.5.1.14.2.1.2 | A collection of objects for controlling the redistribution of external routes by OSPF. | ||
| IP hpicfOspfRedistRestrictAddr | 1.3.6.1.4.1.11.2.14.11.5.1.14.1.3.1.1 | IpAddress | not-accessible | The IP address of the range of route entries to exclude from redistribution into OSPF. |
| hpicfOspfRedistRestrictEntry | 1.3.6.1.4.1.11.2.14.11.5.1.14.1.3.1 | not-accessible | A single entry in the table. Any route, regardless of source protocol which is contained within the specified range will not be redistributed into OSPF. Entries in this table are created dynamically using the hpicfOspfRedistRestrictStatus object. | |
| IP hpicfOspfRedistRestrictMask | 1.3.6.1.4.1.11.2.14.11.5.1.14.1.3.1.2 | IpAddress | not-accessible | The mask for the range of route entries to exclude from redistribution into OSPF. |
| ROW hpicfOspfRedistRestrictStatus | 1.3.6.1.4.1.11.2.14.11.5.1.14.1.3.1.3 | RowStatus | read-create | The status of this entry. |
| hpicfOspfRedistRestrictTable | 1.3.6.1.4.1.11.2.14.11.5.1.14.1.3 | not-accessible | A table of route prefixes for filtering out routes that OSPF should not redistribute. Any route that is contained by a range in this table (in other words, has a longer mask than that specified by hpicfOspfRedistRestrictMask and where the route destination ANDed with the hpicfOspfRedistRestrictMask is equal to hpicfOspfRedistRestrictAddr) will not be redistributed as an AS-external LSA by OSPF. | |
| IAN hpicfOspfRedistSrcProto | 1.3.6.1.4.1.11.2.14.11.5.1.14.1.2.1.1 | IANAipRouteProtocol | not-accessible | Source protocol to redistribute routes from. |
| hpicfOspfRedistTable | 1.3.6.1.4.1.11.2.14.11.5.1.14.1.2 | not-accessible | Table for configuring route redistribution into OSPF. | |
| MET hpicfOspfReferenceCost | 1.3.6.1.4.1.11.2.14.11.5.1.14.1.1.11 | Metric | read-write | The reference cost is used as a global configuration for internal area cost. |
| hpicfOspfReferenceGroup | 1.3.6.1.4.1.11.2.14.11.5.1.14.2.1.15 | Elements in the global cost context | ||
| I32 hpicfOspfReqAge | 1.3.6.1.4.1.11.2.14.11.5.1.14.9.1.5 | Integer32 | read-only | This Request list's field is the age of the link state advertisement in seconds. |
| I32 hpicfOspfReqChecksum | 1.3.6.1.4.1.11.2.14.11.5.1.14.9.1.6 | Integer32 | read-only | This Request list's field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagram's; it is commonly referred to as the Fletcher checksum. |
| hpicfOspfReqCompliance | 1.3.6.1.4.1.11.2.14.11.5.1.14.2.2.2 | The compliance statement for show Requestlist command. | ||
| hpicfOspfReqEntry | 1.3.6.1.4.1.11.2.14.11.5.1.14.9.1 | not-accessible | A Request List entries that contain fields of link state advertisement. | |
| hpicfOspfReqGroup | 1.3.6.1.4.1.11.2.14.11.5.1.14.2.3.2 | This is a normal group that gives checksum,sequence and age related information | ||
| hpicfOspfReqGroups | 1.3.6.1.4.1.11.2.14.11.5.1.14.2.3 | |||
| IP hpicfOspfReqLsid | 1.3.6.1.4.1.11.2.14.11.5.1.14.9.1.2 | IpAddress | read-only | The Request List's Link State ID is an LS Type Specific field containing either a Router ID or an IP address; it identifies the piece of the routing domain that is being described by the advertisement. |
| hpicfOspfReqManGroup | 1.3.6.1.4.1.11.2.14.11.5.1.14.2.3.1 | A mandatory group that displays ID information with Respect to Link state,router,interface and the LSA type | ||
| IP hpicfOspfReqRouterId | 1.3.6.1.4.1.11.2.14.11.5.1.14.9.1.3 | IpAddress | read-only | The 32-bit number that uniquely identifies the originating router in the Autonomous System. |
| I32 hpicfOspfReqSequence | 1.3.6.1.4.1.11.2.14.11.5.1.14.9.1.4 | Integer32 | read-only | The Request List's sequence number field is a signed 32-bit integer. It starts with the value '80000001'h, or -'7FFFFFFF'h, and increments until '7FFFFFFF'h. Thus, a typical sequence number will be very negative. It is used to detect old and duplicate Link State Advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number, the more recent the advertisement. |
| hpicfOspfReqTable | 1.3.6.1.4.1.11.2.14.11.5.1.14.9 | not-accessible | Request List table that contains OSPF Specific interface information. | |
| INT hpicfOspfReqType | 1.3.6.1.4.1.11.2.14.11.5.1.14.9.1.1 | INTEGER | read-only | The type of the Request List's link state advertisement. Each link state type has a separate advertisement format. |
| I32 hpicfOspfRetransAge | 1.3.6.1.4.1.11.2.14.11.5.1.14.10.1.5 | Integer32 | read-only | This Retransmission List field is the age of the link state advertisement in seconds. |
| I32 hpicfOspfRetransChecksum | 1.3.6.1.4.1.11.2.14.11.5.1.14.10.1.6 | Integer32 | read-only | This Retransmission field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagram's; it is commonly referred to as the Fletcher checksum. |
| hpicfOspfRetransCompliance | 1.3.6.1.4.1.11.2.14.11.5.1.14.2.2.4 | The compliance statement for show Retranslist command. | ||
| hpicfOspfRetransEntry | 1.3.6.1.4.1.11.2.14.11.5.1.14.10.1 | not-accessible | Retransmission list entry that is maintained for an OSPF Interface. | |
| hpicfOspfRetransGroup | 1.3.6.1.4.1.11.2.14.11.5.1.14.2.4.2 | This is a normal group that gives checksum,sequence and age related information | ||
| hpicfOspfRetransGroups | 1.3.6.1.4.1.11.2.14.11.5.1.14.2.4 | |||
| IP hpicfOspfRetransLsid | 1.3.6.1.4.1.11.2.14.11.5.1.14.10.1.2 | IpAddress | read-only | The Retransmission List Link State ID is an LS Type Specific field containing either a Router ID or an IP address; it identifies the piece of the routing domain that is being described by the advertisement. |
| hpicfOspfRetransManGroup | 1.3.6.1.4.1.11.2.14.11.5.1.14.2.4.1 | A mandatory group that displays ID information with Respect to Link state,router,interface and the LSA type | ||
| IP hpicfOspfRetransRouterId | 1.3.6.1.4.1.11.2.14.11.5.1.14.10.1.3 | IpAddress | read-only | The 32-bit number that uniquely identifies the originating Retransmission List router in the Autonomous System. |
| I32 hpicfOspfRetransSequence | 1.3.6.1.4.1.11.2.14.11.5.1.14.10.1.4 | Integer32 | read-only | The Retransmission List sequence number field is a signed 32-bit integer. It starts with the value '80000001'h, or -'7FFFFFFF'h, and increments until '7FFFFFFF'h. Thus, a typical sequence number will be very negative. It is used to detect old and duplicate Link State Advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number, the more recent the advertisement. |
| hpicfOspfRetransTable | 1.3.6.1.4.1.11.2.14.11.5.1.14.10 | not-accessible | Retransmission List table that contains Ospf Interface Specific information. | |
| INT hpicfOspfRetransType | 1.3.6.1.4.1.11.2.14.11.5.1.14.10.1.1 | INTEGER | read-only | The Retransmission List LSA type. Each link state type has a separate advertisement format. |
| hpicfOspfRouteGroup | 1.3.6.1.4.1.11.2.14.11.5.1.14.3 | |||
| hpicfOspfRouterLSAEntry | 1.3.6.1.4.1.11.2.14.11.5.1.14.15.1 | not-accessible | A single Area-Scope Link State Advertisement. | |
| HPI hpicfOspfRouterLSAIfId | 1.3.6.1.4.1.11.2.14.11.5.1.14.15.1.4 | HpicfOspfRouterIdTc | read-only | The interface Id of the router that connects to the other router. |
| U32 hpicfOspfRouterLSAIfType | 1.3.6.1.4.1.11.2.14.11.5.1.14.15.1.2 | Unsigned32 | read-only | The 32-bit identifier of the Area from which the LSA was received. |
| MET hpicfOspfRouterLSAMetric | 1.3.6.1.4.1.11.2.14.11.5.1.14.15.1.3 | Metric | read-only | This field indicates the cost involved in using the interface or route. |
| HPI hpicfOspfRouterLSANbrRtrId | 1.3.6.1.4.1.11.2.14.11.5.1.14.15.1.1 | HpicfOspfRouterIdTc | not-accessible | The router id of the router which is connected over the interface Id. |
| hpicfOspfRouterLSATable | 1.3.6.1.4.1.11.2.14.11.5.1.14.15 | not-accessible | This table having Area scope is a dependent-expansion table for the Router LSA entry in the Area LSDB table. It represents the list of per interface details advertised in a Router LSA. | |
| U32 hpicfOspfRouterLSATOSMetric | 1.3.6.1.4.1.11.2.14.11.5.1.14.15.1.5 | Unsigned32 | read-only | This field indicates the cost involved in using the interface or route specific to TOS. |
| C32 hpicfOspfSentDDPkt | 1.3.6.1.4.1.11.2.14.11.5.1.14.5.1.2 | Counter32 | read-only | The number of Database Description packets sent on the interface. This number is incremented each time an OSPF DD packet is sent out of an OSPF enabled interface. Discontinuities in the value of this counter can occur at re-initialization of the management system. The counters can be cleared for any interface using clear ip ospf statistics command. |
| C32 hpicfOspfSentHelloPktEx | 1.3.6.1.4.1.11.2.14.11.5.1.14.5.1.1 | Counter32 | read-only | The number of OSPF Hello packets sent on the interface. This number is incremented each time an OSPF Hello packet is sent out of an OSPF enabled interface. Discontinuities in the value of this counter can occur at re-initialization of the management system. The counters can be cleared for any interface using clear ip ospf statistics command. |
| C32 hpicfOspfSentLSAPkt | 1.3.6.1.4.1.11.2.14.11.5.1.14.5.1.5 | Counter32 | read-only | The number of Link State Ack packet sent on the interface. This number is incremented each time an OSPF LSA packet is sent out of an OSPF enabled interface. Discontinuities in the value of this counter can occur at re-initialization of the management system. The counters can be cleared for any interface using clear ip ospf statistics command. |
| C32 hpicfOspfSentLSRPkt | 1.3.6.1.4.1.11.2.14.11.5.1.14.5.1.3 | Counter32 | read-only | The number of Link State Request packet sent on the interface. This number is incremented each time an OSPF LSR packet is sent out of OSPF enabled interface. Discontinuities in the value of this counter can occur at re-initialization of the management system. The counters can be cleared for any interface using clear ip ospf statistics command. |
| C32 hpicfOspfSentLSUPkt | 1.3.6.1.4.1.11.2.14.11.5.1.14.5.1.4 | Counter32 | read-only | The number of Link State Update packet sent on the interface. This number is incremented each time an OSPF LSU packet is sent out of an OSPF enabled interface. Discontinuities in the value of this counter can occur at re-initialization of the management system. The counters can be cleared for any interface using clear ip ospf statistics command. |
| hpicfOspfSpfDelayCompliance | 1.3.6.1.4.1.11.2.14.11.5.1.14.2.2.6 | The compliance statement for this module. | ||
| hpicfOspfSpfDelayGroup | 1.3.6.1.4.1.11.2.14.11.5.1.14.2.1.12 | Group for ospfSpfThrottle objects. | ||
| hpicfOspfSpfEntry | 1.3.6.1.4.1.11.2.14.11.5.1.14.8.1 | not-accessible | A list of extensions to the information maintained for OSPF SPF runs. | |
| I32 hpicfOspfSpfInstance | 1.3.6.1.4.1.11.2.14.11.5.1.14.8.1.1 | Integer32 | not-accessible | The hpicfospfSpfInstance refers to the instance of SPF Shortest Path First ran for an OSPF instance. |
| I32 hpicfOspfSpfReason | 1.3.6.1.4.1.11.2.14.11.5.1.14.8.1.2 | Integer32 | read-only | The hpicfOspfSpfReason refers to the reason for scheduling an SPF run. Reasons could be OSPF init, adding/deleting interface, linkStateUpdate received.. Only last ten SPF run's reasons will be saved. |
| hpicfOspfSpfTable | 1.3.6.1.4.1.11.2.14.11.5.1.14.8 | not-accessible | Table that contains OSPF SPF information. | |
| U32 hpicfOspfSpfThrottleCurrentSpfInterval | 1.3.6.1.4.1.11.2.14.11.5.1.14.1.1.10 | Unsigned32 | read-only | Current dynamic wait interval between SPF computations |
| I32 hpicfOspfSpfThrottleMaxWaitTime | 1.3.6.1.4.1.11.2.14.11.5.1.14.1.1.9 | Integer32 | read-write | Maximum wait time between two consecutive SPFs. |
| I32 hpicfOspfSpfThrottleStartInterval | 1.3.6.1.4.1.11.2.14.11.5.1.14.1.1.7 | Integer32 | read-write | Initial SPF schedule delay |
| I32 hpicfOspfSpfThrottleWaitInterval | 1.3.6.1.4.1.11.2.14.11.5.1.14.1.1.8 | Integer32 | read-write | Minimum wait time between two consecutive SPFs. |
| I32 hpicfOspfSpfTime | 1.3.6.1.4.1.11.2.14.11.5.1.14.8.1.3 | Integer32 | read-only | The hpicfOspfSpfTime refers to the time at which SPF run is scheduled. Reasons could be OSPF init, adding/deleting interface, linkStateUpdate received.. Only last ten SPF run's reasons will be saved. |
| U32 hpicfOspfSpfTimerElapsed | 1.3.6.1.4.1.11.2.14.11.5.1.14.12 | Unsigned32 | read-only | The elapsed time since the last Ospf Spf is run |
| hpicfOspfSpfTimerGroup | 1.3.6.1.4.1.11.2.14.11.5.1.14.2.1.5 | Time taken since the last spf Run. | ||
| hpicfOspfStatisticGroup | 1.3.6.1.4.1.11.2.14.11.5.1.14.2.1.4 | A collection of objects that contain OSPF interface and SPF statistics. | ||
| U32 hpicfOspfTOS | 1.3.6.1.4.1.11.2.14.11.5.1.14.14.1.7 | Unsigned32 | read-only | The 32-bit identifier for the TOS specific information of the LSA. |
RFC description
Provides HP proprietary extensions to OSPF routing protocol for advanced ospf network management and monitoring on HP network switches.
Start monitoring HP ProCurve Layer 3 switch/router (OSPF extensions) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.