TP5000E

All MIBs › TP5000E

Organization: Symmetricom

Last Updated: 2018-03-22

Category: Synchronization and Timing

Description: Manages Symmetricom TP5000E timing platform clock sources, synchronization status, and output configuration.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is TP5000E?

TP5000E is a Symmetricom proprietary MIB (equipment-specific subset MIB) for the TP5000e timing/synchronization system. Its objects cover per-LED status, per-hardware-component status text, per-module uptime and warm-up status, and an active-alarm table recording alarm index, associated module ID, and alarm ID. As a hardware-status MIB it lets an administrator confirm all modules have completed warm-up and check for any currently active hardware alarms. It is deployed on the Symmetricom TP5000e timing/synchronization system. Engineers can download the TP5000E file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in TP5000E. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Symmetricom TP5000e timing/synchronization system

Monitoring Examples

An administrator checks tp5000eModWarmUpStatus after a power-up to confirm all modules have completed their warm-up cycle before relying on the TP5000e as a precision timing reference.

What Can Be Monitored

module warm-up/uptime status
active hardware alarms

Imported Objects

From ENTITY-MIB

entPhysicalIndex

OBJECT-TYPE

From IF-MIB

ifIndex	OBJECT-TYPE
ifNumber	OBJECT-TYPE

From INET-ADDRESS-MIB

InetAddressIPv6

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-IDENTITY
OBJECT-TYPE
Unsigned32
snmpModules

From SNMPv2-TC

DisplayString
RowStatus
TEXTUAL-CONVENTION

From SYMM-COMMON-SMI

ACTIONONLY
EnableValue
ONVALUETYPE
TP5000MODULEID
YESVALUETYPE
symmDeviceDependent	OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
tp5000e	1.3.6.1.4.1.9070.1.2.5.7.1			This MIB is the equipment-specific subset MIB for the TP5000e system.
tp5000eSystemStatus	1.3.6.1.4.1.9070.1.2.5.7.1.1
tp5000eLedTable	1.3.6.1.4.1.9070.1.2.5.7.1.1.1		not-accessible	This is a table of the front panel LED status for a specified module. The module can be IMC, IOC1, IOC2, or an expansion shelf.
tp5000eLedEntry	1.3.6.1.4.1.9070.1.2.5.7.1.1.1.1		not-accessible	An entry of the LED table contains status for one of the LEDs in a specified module. This table has a double index: entPhysicalIndex and tp5000LEDID.
TP5 tp5000eLedID	1.3.6.1.4.1.9070.1.2.5.7.1.1.1.1.1	TP5000LEDID	read-only	LED ID are LED names on the module front panel. Currently, the TP5000E system has 14 unique LED names. Some LED names (ALM and MGMT) are used on different module types. IMC LEDs: 1) BT A (battery terminal A-bus power) 2) BT B (battery terminal B-bus power) 3) SYS (system health) 4) ALM (IMC alarm) 5) GNSS/GPS (GNSS/GPS status) 6) MGMT (Ethernet management port) IOC LEDs: 7) ACT (active IOC) 8) Alarm (IOC alarm) 9) ETH1 (Ethernet port 1) 10) ETH2 (Ethernet port 2) 11) Holdover (IOC oscillator status) Expansion shelf LEDs: 13) PWR A (A-bus power) 14) PWR B (B-bus power) 4) ALM (expansion shelf alarm) 6) MGMT (Ethernet management port) 12) REF (reference tracking status)
TP5 tp5000eLedStatus	1.3.6.1.4.1.9070.1.2.5.7.1.1.1.1.2	TP5000LEDTYPE	read-only	LED status can be one of the following: Off(0), On(1), Red(2), Redblink(3), Green(4), Greenblink(5), Amber(6), Amberblink(7)
tp5000eHWStatusTable	1.3.6.1.4.1.9070.1.2.5.7.1.1.2		not-accessible	Table of hardware status for a specified module (IMC, IOC1, IOC2, or an expansion shelf). It includes power supply voltages and other status information for the module hardware.
tp5000eHWStatusEntry	1.3.6.1.4.1.9070.1.2.5.7.1.1.2.1		not-accessible	An entry of hardware status table. The table index is entPhysicalIndex.
I32 tp5000eHWStatusIndex	1.3.6.1.4.1.9070.1.2.5.7.1.1.2.1.1	Integer32	not-accessible	Local index of the TP5000E hardware status table.
STR tp5000eHWStatusInfo	1.3.6.1.4.1.9070.1.2.5.7.1.1.2.1.2	DisplayString	read-only	For each module, the hardware status information is DisplayString type, and has a list of hardware status (power supply voltages, etc.). Example for IMC: -48V-A : ok -48V-B : ok +1.2V : 1.211V +1.8V : 1.843V +2.5V : 2.526V +5.5V : 5.490V VCXO : 2.526V GPS Power : 5.464V GPS Current : 24mA GPS Antenna : ok FPGA : ok Example for an IOC: +1.8V : 1.805V 10M EFC : 1.116V 20M EFC : 0.872V 25M EFC : 1.155V 24.5M EFC : 1.155V 24.7M EFC : 1.253V OSC Current : 173mA FPGA VCCint : 1.005V FPGA VCCaux : 2.499V FPGA Temp : 60C FPGA Temp High : 61C FPGA Temp Low : 54C Example for an Ethernet expansion shelf: +1.8V : 1.805V 12V : 12.116V 2.5V : 2.572V 1.2V : 1.17V 0.9V : 1.0V 1.0V : 1.1V 5V : 5.01V 1.1A: 1.5A: 2.5A: 1.1B: 1.5B: 2.5B: Temperature : 54C Example for an E1/TOD expansion shelf: +1.8V : 1.805V 5 V : 5.016V 2.5 V : 2.520V 1.2 V : 1.1805V TIM2.5 V : 2.505V 1.0V : 1.053V TIM1.2V : 1.990V
tp5000eModUpTimeTable	1.3.6.1.4.1.9070.1.2.5.7.1.1.3		not-accessible	Module up time for a specified module (IMC, IOC1, IOC2, or an expansion shelf).
tp5000eModUpTimeEntry	1.3.6.1.4.1.9070.1.2.5.7.1.1.3.1		not-accessible	An entry of the module up time table. The table index is entPhysicalIndex.
I32 tp5000eModUpTimeIndex	1.3.6.1.4.1.9070.1.2.5.7.1.1.3.1.1	Integer32	not-accessible	Local index of the module up time table.
STR tp5000eModuleUpTime	1.3.6.1.4.1.9070.1.2.5.7.1.1.3.1.2	DisplayString	read-only	Module up time status for the module is a DisplayString type. Example for IMC: IMC uptime: 7 days 2 hrs 18 mins
tp5000eModWarmUpTable	1.3.6.1.4.1.9070.1.2.5.7.1.1.4		not-accessible	Table of warm-up status for a specified module (IMC, IOC1, IOC2, or an expansion shelf).
tp5000eModWarmUpEntry	1.3.6.1.4.1.9070.1.2.5.7.1.1.4.1		not-accessible	An entry of the module warm-up status table. The table index is entPhysicalIndex.
I32 tp5000eModWarmUpIndex	1.3.6.1.4.1.9070.1.2.5.7.1.1.4.1.1	Integer32	not-accessible	Local index of the module warm-up status table.
STR tp5000eModWarmUpStatus	1.3.6.1.4.1.9070.1.2.5.7.1.1.4.1.2	DisplayString	read-only	Module warm-up status for the module is a DisplayString type. Example for an IOC: IOC1 warm-up status: complete (total 1651 secs)
tp5000eModStatusTable	1.3.6.1.4.1.9070.1.2.5.7.1.1.5		not-accessible	Table of operating status for a specified module in the system (IMC, IOC1, IOC2, or an expansion shelf).
tp5000eModStatusEntry	1.3.6.1.4.1.9070.1.2.5.7.1.1.5.1		not-accessible	An entry of the module operating status table. The table index is entPhysicalIndex.
I32 tp5000eModStatusIndex	1.3.6.1.4.1.9070.1.2.5.7.1.1.5.1.1	Integer32	not-accessible	Local index of the module general status table.
STR tp5000eModStatusInfo	1.3.6.1.4.1.9070.1.2.5.7.1.1.5.1.2	DisplayString	read-only	A list of operating status parameters for the module. Example for main shelf status information: System name: TP5000 IMC time: 2010-03-08 20:33:30 IMC uptime: 7 days 2 hrs 18 mins IOC1 warmup status: complete (total 1651 secs) IOC1 state: active IOC1 uptime: 7 days 2 hrs 18 mins IOC2 warmup status: n/a IOC2 state: card not present IOC2 uptime: card not present Reference mode: time Current reference input: GPS Phase offset: 0 ns Clock status: normal track PTP mode eth1: multicast grandmaster PTP mode eth2: multicast grandmaster Active alarms: 1 Exp connections: 1,3,6,9 Example for an Ethernet expansion shelf status information: Expansion shelf: PTP-SyncE Shelf time: 2010-03-08 20:33:30 Shelf uptime: 7 days 2 hrs 18 mins Phase Offset: 0 ns Main Clock status: normal track Shelf clock status: normal track Combined Clock status: normal track PTP mode: multicast grandmaster SyncE output PQL: 2 Example of an E1/TOD expansion shelf status information: Expansion shelf: E1-TOD shelf time : 2010-03-08 20:33:30 shelf uptime : 7 days 2 hrs 18 mins Phase offset : 0 ns Main clock status : normal track Shelf clock status: normal track Combined Clock status: normal track E1 output PQL: 2
tp5000eAlarmAndEvent	1.3.6.1.4.1.9070.1.2.5.7.1.2
tp5000eActAlarmTable	1.3.6.1.4.1.9070.1.2.5.7.1.2.1		not-accessible	List of alarms that are still active in the TP5000E system.
tp5000eActAlarmEntry	1.3.6.1.4.1.9070.1.2.5.7.1.2.1.1		not-accessible	Entry for one active alarm in the active alarm table. The table index is the local index.
INT tp5000eActAlarmIndex	1.3.6.1.4.1.9070.1.2.5.7.1.2.1.1.1	INTEGER	read-only	The access (local) index of the active alarm table. The range of the table index is 1 to 500.
TP5 tp5000eActAlarmModID	1.3.6.1.4.1.9070.1.2.5.7.1.2.1.1.2	TP5000MODULEID	read-only	Name of the hardware module that generated this active alarm. In TP5000E system, the module name can be one of the following: SYS, IMC, IOC1, IOC2, IO, Exp0, Exp1,... Exp9. The module ID is only used to show the module name of a physical entity, but it is never used as an index. Indexing is done using entPhysicalIndex.
U32 tp5000eActAlarmID	1.3.6.1.4.1.9070.1.2.5.7.1.2.1.1.3	Unsigned32	read-only	The alarm ID uniquely identifies an alarm type. All alarm IDs are listed and described in the User Guide.
U32 tp5000eActAlarmInternalIndex	1.3.6.1.4.1.9070.1.2.5.7.1.2.1.1.4	Unsigned32	read-only	See alarm second index in User Guide.
STR tp5000eActAlarmDateTime	1.3.6.1.4.1.9070.1.2.5.7.1.2.1.1.5	DisplayString	read-only	The date and time stamp for this active alarm. It is the time when the alarm was reported.
ALA tp5000eActAlarmSeverity	1.3.6.1.4.1.9070.1.2.5.7.1.2.1.1.6	ALARMLEVELTYPE	read-only	The alarm severity level can be one of the following: -critical(2), critical condition -major(3), error condition -minor(4), warning condition -event(5), normal but significant condition
STR tp5000eActAlarmDesc	1.3.6.1.4.1.9070.1.2.5.7.1.2.1.1.7	DisplayString	read-only	A description for the alarm. For a complete description of all alarms, please see the User Guide. A portion of the alarm and event table is shown below: ID Level State Delay transient Descriptions --------------------------------------------------- 0 critical enable 0 no Communication to peer card failed 1 minor enable 0 no GNSS receiver communications failed 2 minor enable 0 no GNSS receiver not tracking satellite 3 major enable 0 no TOD source invalid 4 event enable 0 yes TOD has been set by TOD source 5 event enable 0 yes System log time has been updated
tp5000eActEventTable	1.3.6.1.4.1.9070.1.2.5.7.1.2.2		not-accessible	List of events that are still active in the TP5000E system.
tp5000eActEventEntry	1.3.6.1.4.1.9070.1.2.5.7.1.2.2.1		not-accessible	An entry for one active event in the active event table. The table index is the local index.
INT tp5000eActEventIndex	1.3.6.1.4.1.9070.1.2.5.7.1.2.2.1.1	INTEGER	read-only	The access (local) index of the active event table. The range of the table index is 1 to 500.
TP5 tp5000eActEventModID	1.3.6.1.4.1.9070.1.2.5.7.1.2.2.1.2	TP5000MODULEID	read-only	Name of the hardware module that reported the event. Module ID can be one of the following: SYS, IMC, IOC1, IOC2, or Exp0, Exp1,... Exp9. The module ID is only used to show the module name of a physical entity, but it is never used as an index. Indexing is done using entPhysicalIndex.
U32 tp5000eActEventID	1.3.6.1.4.1.9070.1.2.5.7.1.2.2.1.3	Unsigned32	read-only	The event ID uniquely identifies an event type. All event IDs are listed and described in the User Guide.
U32 tp5000eActEventInternlIndex	1.3.6.1.4.1.9070.1.2.5.7.1.2.2.1.4	Unsigned32	read-only	See alarm second index in User Guide.
STR tp5000eActEventDateTime	1.3.6.1.4.1.9070.1.2.5.7.1.2.2.1.5	DisplayString	read-only	The date and time stamp for this active event. It is the time when the event was reported.
STR tp5000eActEventDesc	1.3.6.1.4.1.9070.1.2.5.7.1.2.2.1.6	DisplayString	read-only	A description for the event. For a complete description of all events, please see the User Guide.
tp5000eAlarmConfigTable	1.3.6.1.4.1.9070.1.2.5.7.1.2.3		not-accessible	The alarm configuration table. Each alarm is defined by five alarm configuration parameters: alarm id, alarm severity level, delay time, enable state, and a description.
tp5000eAlarmConfigEntry	1.3.6.1.4.1.9070.1.2.5.7.1.2.3.1		not-accessible	Entries of the alarm configuration table. Table index is a local index.
INT tp5000eAlarmConfigIndex	1.3.6.1.4.1.9070.1.2.5.7.1.2.3.1.1	INTEGER	read-only	The index of the alarm configuration table. The range of the table index is 1 to 500.
U32 tp5000eAlarmConfigAID	1.3.6.1.4.1.9070.1.2.5.7.1.2.3.1.2	Unsigned32	read-only	This value is the Alarm ID. The alarm definition for each ID is defined in the User Guide.
ALA tp5000eAlarmLevelSetting	1.3.6.1.4.1.9070.1.2.5.7.1.2.3.1.3	ALARMLEVELTYPE	read-write	The alarm severity level can be one of the following: 2 Critical: critical condition 3 Major: error condition 4 Minor: warning condition 5 Event: normal but significant condition
I32 tp5000eAlarmSettingDelay	1.3.6.1.4.1.9070.1.2.5.7.1.2.3.1.4	Integer32	read-write	Alarm delay in seconds. The alarm is not reported if the alarm condition disappears before this delay time is up. The purpose of the alarm delay is to prevent reporting intermittent conditions. The range of the alarm delay is 0 to 84,600 seconds. Default value is 0.
ENA tp5000eEnableAlarmState	1.3.6.1.4.1.9070.1.2.5.7.1.2.3.1.5	EnableValue	read-write	Alarm state control flag. The flag can be Enable (1) or Disable (2). The default value is Enable. If an alarm is disabled, the system will never report conditions associated with this alarm.
STR tp5000eAlarmConfigDesc	1.3.6.1.4.1.9070.1.2.5.7.1.2.3.1.6	DisplayString	read-only	Alarm description (from hardcoded alarm definition table).
I32 tp5000eNumofStandingAlarm	1.3.6.1.4.1.9070.1.2.5.7.1.2.4	Integer32	read-only	The total number of currently active alarms in the TP5000E system, including those generated by the expansion shelves.
ONV tp5000eMessageGenerate	1.3.6.1.4.1.9070.1.2.5.7.1.2.5	ONVALUETYPE	read-write	This flag is used to generate all TP5000E alarm and event messages with this one action. The messages are sent to the alarm and event logs. This feature is used for testing purposes. For a message that specifies a port, only one message is generated instead of generating a message for each possible port. This object is actually write-only, but SNMP does not have write-only.
tp5000eGlobalConfig	1.3.6.1.4.1.9070.1.2.5.7.1.3
tp5000eLogFileConfigTable	1.3.6.1.4.1.9070.1.2.5.7.1.3.1		not-accessible	The log file table is used to configure the sizes of various log files. There are four log files: alarm log, event log, command log, and security log.
tp5000eLogFileConfigEntry	1.3.6.1.4.1.9070.1.2.5.7.1.3.1.1		not-accessible	An entry of the log file configuration table. Table index is the local index.
I32 tp5000eLogFileConfigIndex	1.3.6.1.4.1.9070.1.2.5.7.1.3.1.1.1	Integer32	read-only	The local index of the log file configuration table.
STR tp5000eLogFileTypeName	1.3.6.1.4.1.9070.1.2.5.7.1.3.1.1.2	DisplayString	read-only	The log file name can be one of the following: Alarm, Event, Command, or Security. All alarm messages go into the alarm log. All event messages go into the event log. All user entered commands are recorded in the command log, except those commands related to user login and logout. All user login and logout commands are stored in the security log.
U32 tp5000eLogFileBufferSize	1.3.6.1.4.1.9070.1.2.5.7.1.3.1.1.3	Unsigned32	read-write	The size for the specified log file. Log file size is specified in unit of Kbytes. The default and the maximum size is 100 KB per log.
tp5000eRemoteSyslogTable	1.3.6.1.4.1.9070.1.2.5.7.1.3.2		not-accessible	Remote syslog file control table. It is used to configure a remote syslog server to receive log messages from TP5000K system. Only one remote syslog server is supported at this time.
tp5000eRemoteSyslogEntry	1.3.6.1.4.1.9070.1.2.5.7.1.3.2.1		not-accessible	An entry of the remote syslog file control table.
I32 tp5000eRemoteSyslogIndex	1.3.6.1.4.1.9070.1.2.5.7.1.3.2.1.1	Integer32	read-only	The local index of the remote syslog file control table. At this time only the index value of 1 is supported.
ENA tp5000eRemoteSyslogState	1.3.6.1.4.1.9070.1.2.5.7.1.3.2.1.2	EnableValue	read-write	The remote syslog state control. The setting can be either Enable (1) or Disable (2). Once this is set to Enable, all TP5000E log messages (intended for any of the four built-in logs) will be sent to the remote syslog server.
IP tp5000eRemoteSyslogAddr	1.3.6.1.4.1.9070.1.2.5.7.1.3.2.1.3	IpAddress	read-write	The IP address of the remote syslog machine. The format is xxx.xxx.xxx.xxx. It suports only IPv4 format. 0.0.0.0 denotes remote-syslog address is IPv6
tp5000eRedundTable	1.3.6.1.4.1.9070.1.2.5.7.1.3.3		not-accessible	The port redundancy table for IOC modules. Currently the system is hardcoded for card redundancy. The only redundancy selection is whether to enable port redundancy within a module (port bonding).
tp5000eRedundEntry	1.3.6.1.4.1.9070.1.2.5.7.1.3.3.1		not-accessible	An entry of the IOC port redundancy table. Table index is module index
TP5 tp5000eRedundModuleID	1.3.6.1.4.1.9070.1.2.5.7.1.3.3.1.1	TP5000MODULEID	read-only	The module ID can be either IOC1 or IOC2. The system is currently hardcoded for card redundancy (if two IOC cards are present, they are always configured as a redundancy pair, with one active and one on standby). Whichever module ID is used to access this table, the configuration will apply to both IOC cards. In the future when the two IOC cards can be independent, configuration will only apply to the current IOC module.
ENA tp5000eRedundModState	1.3.6.1.4.1.9070.1.2.5.7.1.3.3.1.2	EnableValue	read-write	Port redundancy state can be either Enable (1) or Disable (2). When it is Enable, the two Ethernet ports on the specified IOC module will form a bonded pair. When two ports are bonded, they share the same IP address, but only one port is active; the other port is in standby mode.
TP5 tp5000eRedundActivePort	1.3.6.1.4.1.9070.1.2.5.7.1.3.3.1.3	TP5000IOCPORTID	read-write	The port ID of the active port on an IOC module. The active port ID is either Eth1 (1) or Eth2 (2). This object can be used to set the desired port to be the active port; the other port automatically becomes the standby port.
tp5000eImageTable	1.3.6.1.4.1.9070.1.2.5.7.1.3.4		not-accessible	Firmware image information for the selected module (IMC, IOC1, IOC2, or an expansion shelf). In TP5000E, each module can store two firmware images. The image that is selected as the active image will be used when the module is booted up next time. Two images are used in upgrading or downgrading. Image downloading is done through CLI only.
tp5000eImageEntry	1.3.6.1.4.1.9070.1.2.5.7.1.3.4.1		not-accessible	Entry of the firmware image table. Each entry contains objects of each module image information. The image table index is the entPhysicalIndex.
I32 tp5000eImageIndex	1.3.6.1.4.1.9070.1.2.5.7.1.3.4.1.1	Integer32	not-accessible	Local index of the firmware image table.
YES tp5000eImageNextBoot	1.3.6.1.4.1.9070.1.2.5.7.1.3.4.1.2	YESVALUETYPE	read-write	This field indicates whether the board will be booted from this firmware image next time. Values can be either 'yes' or 'no.' Only one of the images can be selected for next boot. The field for the other image is automatically updated accordingly.
INT tp5000eImageID	1.3.6.1.4.1.9070.1.2.5.7.1.3.4.1.3	INTEGER	read-only	For each module, there are up to two images. The range of image ID is 1 and 2.
TP5 tp5000eImageCurrState	1.3.6.1.4.1.9070.1.2.5.7.1.3.4.1.4	TP5000IMAGEACTIVE	read-only	The current state of whether an image active or not. The value is either active (1) or inactive (2).
STR tp5000eImageInfoMsg	1.3.6.1.4.1.9070.1.2.5.7.1.3.4.1.5	DisplayString	read-only	The information message for an image.
tp5000eRebootTable	1.3.6.1.4.1.9070.1.2.5.7.1.3.5		not-accessible	The action to reboot a specified module (IMC, IOC1, IOC2, or an expansion shelf).
tp5000eRebootEntry	1.3.6.1.4.1.9070.1.2.5.7.1.3.5.1		not-accessible	An entry contains objects of the module reboot information. The table index is entPhysicalIndex. Depending on the entPhysicalIndex, reboot can apply to the whole system (stack), a chassis, or a module.
I32 tp5000eRebootIndex	1.3.6.1.4.1.9070.1.2.5.7.1.3.5.1.1	Integer32	not-accessible	Local index of the module reboot table.
ACT tp5000eRebootAction	1.3.6.1.4.1.9070.1.2.5.7.1.3.5.1.2	ACTIONONLY	read-write	The action to reboot the module. Value is either Apply (1) or Nonapply (2). The active firmware image is used when the module is rebooted. Use tp5000eImageTable to select the active image.
tp5000eAuthRADIUSTable	1.3.6.1.4.1.9070.1.2.5.7.1.3.6		not-accessible	This table contains IP addresses and access keys for the Radius authentication server. Radius enable state is set in tp5000eRadiusState outside of this table.
tp5000eAuthRADIUSEntry	1.3.6.1.4.1.9070.1.2.5.7.1.3.6.1		not-accessible	An entry of the RADIUS table.
INT tp5000eAuthRADIUSIndex	1.3.6.1.4.1.9070.1.2.5.7.1.3.6.1.1	INTEGER	read-only	A local index to the RADIUS table. Currently the system only supports RADIUS index value of 1.
IP tp5000eServerRADIUSIPAddress	1.3.6.1.4.1.9070.1.2.5.7.1.3.6.1.2	IpAddress	read-write	The RADIUS server's IP address. Format for IPv4 address is xxx.xxx.xxx.xxx. An IP address cannot be set up if authRADIUS key value is none.
STR tp5000eAuthRADIUSKey	1.3.6.1.4.1.9070.1.2.5.7.1.3.6.1.3	DisplayString	read-write	Authentication key for RADIUS server access.
STR tp5000eAssetNum	1.3.6.1.4.1.9070.1.2.5.7.1.3.7	DisplayString	read-write	User assigned inventory asset number for the system.
NUM tp5000eIntraCommIPSet	1.3.6.1.4.1.9070.1.2.5.7.1.3.8	TP5000INTRAIPSET	read-write	Intra-communication IP set between IMC, IOCs and Expansion shelves. Value can be class A (1), B (2), C (3). Their ranges are: A: IP address range 10.0.250.8 to 10.0.250.47 B: IP address range 172.16.250.8 to 172.16.250.47, C: IP address range 192.168.250.8 to 192.168.250.47 The selected address set cannot be used for external Ethernet ports in this TP5000 system. Therefore, choose a set that does not conflict with the external network configuration. After the value is changed, IMC and IOC or expansion shelves will establish a new connection in 1 to 2 minutes.
ENA tp5000eRadiusState	1.3.6.1.4.1.9070.1.2.5.7.1.3.9	EnableValue	read-write	The RADIUS state can be either Enable (1) or Disable (2). Use tp5000eAuthRadiusTable to configure access to the Radius server.
STR tp5000eLastConfig	1.3.6.1.4.1.9070.1.2.5.7.1.3.10	DisplayString	read-only	The Last Config Update.
tp5000eGlobalService	1.3.6.1.4.1.9070.1.2.5.7.1.4
tp5000ePacketServiceTable	1.3.6.1.4.1.9070.1.2.5.7.1.4.1		not-accessible	This table defines packet service for the specified Ethernet interface on the IOC (main shelf). Currently, this table only applies to the main shelf IOC ports (Eth1 and Eth2); the Ethernet expansion shelves are currently fixed to provide 'PTP grandmaster over Ethernet.'
tp5000ePacketServiceEntry	1.3.6.1.4.1.9070.1.2.5.7.1.4.1.1		not-accessible	An entry of the packet service table. Table index is ifIndex (index for interfaces and ports). The system is currently hardcoded for card redundancy (if two IOC cards are present, they are always configured as a redundancy pair, with one active and one on standby). Regardless of which IOC card ifIndex is used, the configuration will apply to both IOC cards. In the future when the two IOC cards can be independent, configuration will only apply to the IOC module with the current ifIndex.
I32 tp5000ePacketServiceIndex	1.3.6.1.4.1.9070.1.2.5.7.1.4.1.1.1	Integer32	not-accessible	Local index of the packet service selection table.
TP5 tp5000ePacketServiceMode	1.3.6.1.4.1.9070.1.2.5.7.1.4.1.1.2	TP5000PACKETSERVICE	read-write	The packet service for this port. Value can be PTP Grandmaster (1), PTP probe (2), NTP server (3), or NTP probe (4). Note that packet service selection is done for each port, and the two Ethernet ports on the IOC can have different services.
tp5000eSSMOptionTable	1.3.6.1.4.1.9070.1.2.5.7.1.4.2		not-accessible	This is the table for selecting SSM network option for a specified shelf (IOC or Expansion shelf). Main shelf and expansion shelves can each have its own selection of SSM network options.
tp5000eSSMOptionEntry	1.3.6.1.4.1.9070.1.2.5.7.1.4.2.1		not-accessible	An entry of the SSM option table. Table index is entPhysicalIndex.
I32 tp5000eSSMOptionIndex	1.3.6.1.4.1.9070.1.2.5.7.1.4.2.1.1	Integer32	not-accessible	Local index of the SSM option selection table.
TP5 tp5000eSSMOption	1.3.6.1.4.1.9070.1.2.5.7.1.4.2.1.2	TP5000SSMOPTION	read-write	Network option for SSM can be Option 1 (1) or Option 2 (2). Option 1 is for E1 based network. Option 2 is for DS1 based network. ITU-T G.781 and G.8265.1 specifies different SSM (QL) values for Option 1 and Option 2 networks.
INT tp5000ePTPClientDataTableLock	1.3.6.1.4.1.9070.1.2.5.7.1.4.3	INTEGER	read-write	The ptpClientDataTableLock will control the internal semaphore to lock or unlock the ptpClientDataTable. The table must be locked before it can be read. When the ptpClientDataTable is locked, the data in the table will not change. The ptpClientDataTableLock can be set up to be locked or to be unlocked. When the locked signal is issued, the internal semaphore will be increased and start to lock the ptpClientDataTable. When the unlocked signal is issued, the internal semaphore will be decreased. When the semaphore reaches zero (0), the ptpClientDataTable will be unlocked.
INT tp5000ePacketServiceExtendedMode	1.3.6.1.4.1.9070.1.2.5.7.1.4.4	INTEGER	read-write	Fixed configuration. IOC1-1: PTP-GM IOC1-2: NTP-Server
tp5000ePTPClientMgmt	1.3.6.1.4.1.9070.1.2.5.7.1.5
tp5000eReferenceStatus	1.3.6.1.4.1.9070.1.2.5.7.1.6
tp5000eInputPQLTable	1.3.6.1.4.1.9070.1.2.5.7.1.6.1		not-accessible	Status table for a specified reference input. PQL (priority quality level) is reference quality used internally by the TP5000E system. Input SSM and other reference quality indicators are first mapped to PQL, and further processing is carried out using PQL.
tp5000eInputPQLEntry	1.3.6.1.4.1.9070.1.2.5.7.1.6.1.1		not-accessible	An entry of the reference input status table. Index of the table is ifIndex.
STR tp5000eInputRefName	1.3.6.1.4.1.9070.1.2.5.7.1.6.1.1.1	DisplayString	read-only	The name of the reference. Currently supported references are GNSS, GPS, 1PPS+TOD1, 1PPS+TOD2, Span input 1, and Span input 2.
I32 tp5000eInputRefActualPQL	1.3.6.1.4.1.9070.1.2.5.7.1.6.1.1.2	Integer32	read-only	This PQL value either corresponds to the actual SSM value in the reference (when SSM is available) or the default PQL value for the reference.
TP5 tp5000eInputRefQualified	1.3.6.1.4.1.9070.1.2.5.7.1.6.1.1.3	TP5000REFQUALIFICATION	read-only	This is the selection status for the reference. Its value is one of the following: Disabled, Disqualified, Qualified, or Selected.
tp5000eSymmMetrics	1.3.6.1.4.1.9070.1.2.5.7.1.6.2
tp5000eRefConfig	1.3.6.1.4.1.9070.1.2.5.7.1.7
TP5 tp5000eRefTimingMode	1.3.6.1.4.1.9070.1.2.5.7.1.7.1	TP5000REFTIMINGMODE	read-write	The timing mode of the entire TP5000E system, and it can be either Time (1) or Frequency (2). Whether the system is in Time or Frequency mode affects how time and frequency references are used in reference selection. A time reference has both frequency and time-of-day (TOD) information and can be used for both time and frequency synchronization. Examples of time references are: GNSS, GPS, 1PPT+TOD, and PTP. A frequency reference does not have TOD information and can be used only for frequency synchronization. Examples of frequency references are: 2048 kHz, 2048 kbps, 1544 kHz, 1544 kbps, SyncE, and 10 MHz.
TP5 tp5000eRefSelectionCriteria	1.3.6.1.4.1.9070.1.2.5.7.1.7.2	TP5000REFSELECTMODE	read-write	Reference selection criteria applies to the entire TP5000E system, and it can be Priority based (2) or SSM based (3). Manual mode (1) is currently not supported. References are assigned priorities and PQL values, either by default or by user input. PQL values used to relate only to SSM values of E1/T1/SynE signals, but now PQL also covers time signals such as GNSS, GPS, and 1PPS+TOD. For a mapping for currently supported references, please see the user guide.
tp5000eRefConfigTable	1.3.6.1.4.1.9070.1.2.5.7.1.7.3		not-accessible	The reference configuration table is used to configure reference selection parameters for a specified reference input. Configuration parameters include reference name, reference enable state, reference priority, reference PQL enable state, and user configured PQL value. PQL (priority quality level) is reference quality used internal by the TP5000E system. Input SSM and other reference quality indicators are first mapped to PQL, and further processing is carried out using PQL.
tp5000eRefConfigEntry	1.3.6.1.4.1.9070.1.2.5.7.1.7.3.1		not-accessible	An entry of the reference configuration table. Table index is the ifIndex (port index).
STR tp5000eRefName	1.3.6.1.4.1.9070.1.2.5.7.1.7.3.1.1	DisplayString	read-only	Name of the reference. Examples: GNSS, GPS, E1, 1PPS+TOD.
ENA tp5000eRefState	1.3.6.1.4.1.9070.1.2.5.7.1.7.3.1.2	EnableValue	read-write	Reference input state can be either Enable (1) or Disable (2). Only enabled references are used in reference selection.
I32 tp5000eRefPriority	1.3.6.1.4.1.9070.1.2.5.7.1.7.3.1.3	Integer32	read-write	Priority value assigned to a reference. Its range is 1 to 16. It is used as one of the selection criteria for reference selection.
ENA tp5000eRefPQLState	1.3.6.1.4.1.9070.1.2.5.7.1.7.3.1.4	EnableValue	read-write	The PQL state of a reference can be either Enable (1) or Disable (2). If PQL is enabled for a reference, the actual PQL value that the system uses either corresponds to the reference SSM value (when SSM is available) or is the default PQL value (when SSM is not available). If the PQL is disabled, the actual PQL value that the system uses matches the user configured reference PQL value (tp5000eRefPQL).
I32 tp5000eRefPQL	1.3.6.1.4.1.9070.1.2.5.7.1.7.3.1.5	Integer32	read-write	Configured reference PQL value. Its range is 1 to 3, with 1 indicating the highest quality level. This PQL value is used when the reference PQL state is disabled, meaning 'do not use the PQL that comes with the reference but use this value.' This value along with disabling the PQL state is used to override the input PQL
tp5000eClock	1.3.6.1.4.1.9070.1.2.5.7.1.8
tp5000eClockStatus	1.3.6.1.4.1.9070.1.2.5.7.1.8.1
tp5000eClockStatusTable	1.3.6.1.4.1.9070.1.2.5.7.1.8.1.1		not-accessible	This table contains status information for the clock in each shelf.
tp5000eClockStatusEntry	1.3.6.1.4.1.9070.1.2.5.7.1.8.1.1.1		not-accessible	An entry in the Clock Status Table. Table index is entPhysicalIndex (a shelf or a module).
I32 tp5000eClockStatusIndex	1.3.6.1.4.1.9070.1.2.5.7.1.8.1.1.1.1	Integer32	not-accessible	Local index of the module clock status table.
TP5 tp5000eServoControlStatus	1.3.6.1.4.1.9070.1.2.5.7.1.8.1.1.1.2	TP5000SERVOCTL	read-only	The clock servo status of clock module (IOC or expansion). This status is also called clock status in CLI. For expansion shelves, the clock status is the combined status of the cascaded main shelf clock and the expansion shelf clock. The clock status can be one of the following: (1) Warm-up (2) Free-run (3) Fast-track (4) Normal track (5) Holdover (6) Bridging (7) Fail (8) Offline (9) Extended holdover (10) Local free-run (11) Local holdover
STR tp5000ePhaseOffset	1.3.6.1.4.1.9070.1.2.5.7.1.8.1.1.1.3	DisplayString	read-only	This is the phase offset in ns between the reference and output. This is applicable only when the selected reference is a time reference.
tp5000eClockConfig	1.3.6.1.4.1.9070.1.2.5.7.1.8.2
U32 tp5000eBridgingTime	1.3.6.1.4.1.9070.1.2.5.7.1.8.2.1	Unsigned32	read-write	Bridging time in seconds. Range 100-200000. Default value Bridging is a clock state between normal tracking and holdover. When all references are lost, the clock declares that it is going into holdover after the bridging time has elapsed. During bridging, the clock maintains its specification for tracking. Default value is 900
ENA tp5000eAutoSync	1.3.6.1.4.1.9070.1.2.5.7.1.8.2.2	EnableValue	read-write	The auto sync state can be either Enable (1) or Disable (2). Auto sync allows IOC time and IMC time to synchronize when IOC is in time mode passed warmup. If auto sync is disabled, an alarm will be generated when IOC and IMC times are not synchronized. Use tp5000eSync to remove this alarm condition.
STR tp5000eSync	1.3.6.1.4.1.9070.1.2.5.7.1.8.2.3	DisplayString	read-write	This object is used to force system time and phase to synchronize to the selected reference (synchronize between IMC and IOC). This object is write-only, and the value must be 'now.'
U32 tp5000eHoldoverExceededTimeQz	1.3.6.1.4.1.9070.1.2.5.7.1.8.2.4	Unsigned32	read-write	holdover time in seconds for holdover-exceeded-time-qz, Range (0\|900-3000000). 0 is disable
U32 tp5000eHoldoverExceededTimeRb	1.3.6.1.4.1.9070.1.2.5.7.1.8.2.5	Unsigned32	read-write	holdover time in seconds for holdover-exceeded-time-rb, Range (0\|900-3000000). 0 is disable
tp5000eHardwareHierarchy	1.3.6.1.4.1.9070.1.2.5.7.1.9
tp5000eIfTable	1.3.6.1.4.1.9070.1.2.5.7.1.9.1		not-accessible	This table describes physical hierarchy of TP5000E system down to the individual logical interface which can be a physical interface (like GPS port) or a virtual interface (like VLANs at an Ethernet port).
tp5000eIfEntry	1.3.6.1.4.1.9070.1.2.5.7.1.9.1.1		not-accessible	An entry of the TP5000E interface table. Table index is ifIndex.
I32 tp5000eIfIndex	1.3.6.1.4.1.9070.1.2.5.7.1.9.1.1.1	Integer32	read-only	Local index of this table.
TP5 tp5000eIfModuleID	1.3.6.1.4.1.9070.1.2.5.7.1.9.1.1.2	TP5000MODULEID	read-only	Module ID is the name of the physical module. Its value can be one of the following: IMC (2), IOC1 (3), IOC2 (4), IO (5), exp0 (6),... exp9 (15). Module ID is only used to show the name of a physical module. It is not used as an index or sorting key.
I32 tp5000eIfPortID	1.3.6.1.4.1.9070.1.2.5.7.1.9.1.1.3	Integer32	read-only	The current inventory port ID. The range depends on the module ID and P/N index that together uniquely identify port configuration for each module. Example: range for IOC port ID is {1, 2}, and range for E1 expansion shelf is {1... 28}.
U32 tp5000eIfTableIndex	1.3.6.1.4.1.9070.1.2.5.7.1.9.1.1.4	Unsigned32	read-only	The current interface index from ifTable. Each local index is mapped to a corresponding index in the ifTable.
tp5000eEntPhysicalTable	1.3.6.1.4.1.9070.1.2.5.7.1.9.2		not-accessible	This table describes physical hierarchy of TP5000K system down to the module (container) level.
tp5000eEntPhysicalEntry	1.3.6.1.4.1.9070.1.2.5.7.1.9.2.1		not-accessible	An entry of the TP5000E physical entity table. Each entry uniquely identifies the connector configuration (a module may have multiple versions with different connectors).
I32 tp5000eEntPhysicalIndex	1.3.6.1.4.1.9070.1.2.5.7.1.9.2.1.1	Integer32	read-only	Local index of the TP5000E physical entity table.
TP5 tp5000eEntPhysicalModuleID	1.3.6.1.4.1.9070.1.2.5.7.1.9.2.1.2	TP5000MODULEID	read-only	Module ID is the name of the physical module. Its value can be one of the following: IMC (2), IOC1 (3), IOC2 (4), IO (5), exp0 (6),... exp9 (15). Module ID is only used to show the name of a physical module. It is not used as an index or sorting key.
I32 tp5000eEntPhysicalStackID	1.3.6.1.4.1.9070.1.2.5.7.1.9.2.1.3	Integer32	read-only	Stack ID is the ID of the TP5000E system that the current module resides in. Stack ID is currently hardcoded to 1, and NMS needs to use other means (such as IP address) to identify each TP5000E system.
I32 tp5000eEntPhysicalChassisID	1.3.6.1.4.1.9070.1.2.5.7.1.9.2.1.4	Integer32	read-only	Chassis ID is the equipment shelf ID. In TP5000E system, there is one main shelf (chassis ID = 1) and up to ten expansion shelves (chassis ID range 2 to 11).
I32 tp5000eEntPhysicalPartIndex	1.3.6.1.4.1.9070.1.2.5.7.1.9.2.1.5	Integer32	read-only	Part number index uniquely identifies the connector configuration of a given module type. Currently, there are four versions of IMC, and the valid part number index value for IMC are IMC-1 (1), IMC-2 (2), IMC-3 (3), and IMC-4 (4). IOC only has two versions (Rb or Qz), and the valid part number index values for IOC are IOC-Rb (1) and IOC-Qz (2). There are four versions of I/O module, and therefore the range of the I/O module part number index is {1... 4}. Each type of expansion shelf currently does not have multiple versions, so their valid part number index value is only 1 at this time.
I32 tp5000eEntPhysicalTableIndex	1.3.6.1.4.1.9070.1.2.5.7.1.9.2.1.6	Integer32	read-only	Each entry (module) in this table is mapped to an entity index in the entityPhysicalTable in the Entity-MIB.
tp5000eVlanConfig	1.3.6.1.4.1.9070.1.2.5.7.1.10
tp5000eNonfixedVlanTable	1.3.6.1.4.1.9070.1.2.5.7.1.10.1		not-accessible	In the non-fixed VLAN table, VLANs can be added or removed. As a VLAN is added or removed, the table index is updated. The non-fixed VLAN table can hold 484 VLANs (with IfIndex 17 to 500).
tp5000eNonfixedVlanEntry	1.3.6.1.4.1.9070.1.2.5.7.1.10.1.1		not-accessible	An entry of the non-fixed VLAN table. Table index is the local index, but each entry uniquely identifies a VLAN through the IfIndex.
I32 tp5000eNonfixedVlanIndex	1.3.6.1.4.1.9070.1.2.5.7.1.10.1.1.1	Integer32	not-accessible	Local index of the non-fixed VLAN table.
U32 tp5000eNonfixedVlanIfIndex	1.3.6.1.4.1.9070.1.2.5.7.1.10.1.1.2	Unsigned32	read-only	IfIndex of the current non-fixed VLAN (17-500).
TP5 tp5000eNonfixedVlanModuleID	1.3.6.1.4.1.9070.1.2.5.7.1.10.1.1.3	TP5000MODULEID	read-create	Module ID is the name of the physical module (the inventory module ID) in which the current non-fixed VLAN is defined. Module ID is the name of the physical module. Its value can be one of the following: IMC (2), IOC1 (3), IOC2 (4), IO (5), exp0 (6),... exp9 (15). Module ID is only used to show the name of a physical module. It is not used as an index or sorting key.
I32 tp5000eNonfixedVlanPortID	1.3.6.1.4.1.9070.1.2.5.7.1.10.1.1.4	Integer32	read-create	Physical port ID where the current non-fixed VLAN is defined. The range depends on the module ID and P/N index which together uniquely identify port configuration for each module. Example: range for IOC port ID is {1, 2}, and range for E1 expansion shelf is {1... 28}.
INT tp5000eNonfixedVlanId	1.3.6.1.4.1.9070.1.2.5.7.1.10.1.1.5	INTEGER	read-create	The VLAN ID of the current VLAN interface. The range is 0~4094. If a VLAN ID is set to 0, the associated VLAN interface of this VLAN index will be removed from the internal VLAN table. The default VLAN ID of each VLAN interface in the VLAN table is 0. The VLAN ID can be set up only once. The VLAN ID and VLAN Priority must be configured at same time when a VLAN interface row is added. Once a VLAN ID is defined, it cannot be modified. To change it, set the VLAN ID to 0 (deleting the VLAN from the VLAN table) and create a new VLAN row.
I32 tp5000eNonfixedVlanPriority	1.3.6.1.4.1.9070.1.2.5.7.1.10.1.1.6	Integer32	read-create	The priority of the VLAN ID. The range is 0 to 7. VLAN priority and VLAN ID must be configured at same time when a VLAN interface row is added. Once a VLAN priority is defined, it cannot be modified. To change it, set the VLAN ID to 0 (deleting the VLAN from the VLAN table), and create a new VLAN row.
IP tp5000eNonfixedVlanIPv4Addr	1.3.6.1.4.1.9070.1.2.5.7.1.10.1.1.7	IpAddress	read-create	The IPv4 address to which this entry's addressing information pertains. Implementers need to be aware that if the size of ipAddressAddr exceeds 116 octets, OIDS of instances of columns in this row will have more than 128 sub-identifiers and cannot be accessed using SNMPv1, SNMPv2c, or SNMPv3.
IP tp5000eNonfixedVlanNetmask	1.3.6.1.4.1.9070.1.2.5.7.1.10.1.1.8	IpAddress	read-create	The mask of an IPv4 interface. The address format is : xxx.xxx.xxx.xxx.
ENA tp5000eNonfixedVlanState	1.3.6.1.4.1.9070.1.2.5.7.1.10.1.1.9	EnableValue	read-create	This is the state of an individual non-fixed VLAN. Value can be Enable (1) or Disable (2). Setting an individual VLAN state to Enable is not enough for the VLAN to become active. The physical VLAN mode must also be set to Enable (see tp5000eVlanModeTable).
ROW tp5000eNonfixedVlanRowStatus	1.3.6.1.4.1.9070.1.2.5.7.1.10.1.1.10	RowStatus	read-create	The row status of non-fixed VLAN table is used to control row actions. The status column has six defined actions (values): -`active(1)', which indicates that the conceptual row is available for use by the managed device; -`notInService(2)', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device; -`notReady(3)', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; -`createAndGo(4)', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; -`createAndWait(5)', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device);and, -`destroy(6)', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row.
tp5000eFixedVlanTable	1.3.6.1.4.1.9070.1.2.5.7.1.10.2		not-accessible	In the fixed VLAN table, VLANs are pre-assigned to the VLAN table index. They cannot be added or removed from the table.
tp5000eFixedVlanEntry	1.3.6.1.4.1.9070.1.2.5.7.1.10.2.1		not-accessible	An entry of the fixed VLAN table. Table index is ifIndex and local index.
I32 tp5000eFixedVlanIndex	1.3.6.1.4.1.9070.1.2.5.7.1.10.2.1.1	Integer32	not-accessible	Local index of the fixed VLAN table.
INT tp5000eFixedVlanId	1.3.6.1.4.1.9070.1.2.5.7.1.10.2.1.2	INTEGER	read-write	The VLAN ID of the current VLAN interface. The range is 0~4094. If a VLAN ID is set to 0, the associated VLAN interface of this VLAN index will be removed from the internal VLAN table. The default VLAN ID of each VLAN interface in the VLAN table is 0. The VLAN ID can be setup only once. The VLAN ID and VLAN Priority must be configured at same time when a VLAN interface row is added. Once a VLAN ID is defined, it cannot be modified. To change it, set the VLAN ID to 0 (deleting the VLAN from the VLAN table) and create a new VLAN row.
I32 tp5000eFixedVlanPriority	1.3.6.1.4.1.9070.1.2.5.7.1.10.2.1.3	Integer32	read-write	The priority of the VLAN ID. The range is 0 to 7. VLAN priority and VLAN ID must be configured at same time when a VLAN interface row is added. Once a VLAN priority is defined, it cannot be modified. To change it, set the VLAN ID to 0 (deleting the VLAN from the VLAN table), and create a new VLAN row.
IP tp5000eFixedVlanIPv4Addr	1.3.6.1.4.1.9070.1.2.5.7.1.10.2.1.4	IpAddress	read-write	The IPv4 address to which this entry's addressing information pertains. Implementers need to be aware that if the size of ipAddressAddr exceeds 116 octets, OIDS of instances of columns in this row will have more than 128 sub-identifiers and cannot be accessed using SNMPv1, SNMPv2c, or SNMPv3.
IP tp5000eFixedVlanNetmask	1.3.6.1.4.1.9070.1.2.5.7.1.10.2.1.5	IpAddress	read-write	The mask of an IPv4 interface. The address format is : xxx.xxx.xxx.xxx.
IP tp5000eFixedVlanGateway	1.3.6.1.4.1.9070.1.2.5.7.1.10.2.1.6	IpAddress	read-write	The gateway of an IPv4 interface. The address format is : xxx.xxx.xxx.xxx.
ENA tp5000eFixedVlanState	1.3.6.1.4.1.9070.1.2.5.7.1.10.2.1.7	EnableValue	read-write	This is the state of an individual fixed VLAN. Value can be Enable (1) or Disable (2). Setting an individual VLAN state to Enable is not enough for the VLAN to become active. The physical port VLAN mode must also be set to Enable (see tp5000eVlanModeTable).
tp5000eVlanModeTable	1.3.6.1.4.1.9070.1.2.5.7.1.10.3		not-accessible	VLAN mode table. The VLAN mode table is used to enable or disable all VLANs in a physical port.
tp5000eVlanModeEntry	1.3.6.1.4.1.9070.1.2.5.7.1.10.3.1		not-accessible	An entry of the VLAN mode table. Table index is ifIndex (port and interface index) and local index.
I32 tp5000eVlanModeIndex	1.3.6.1.4.1.9070.1.2.5.7.1.10.3.1.1	Integer32	not-accessible	Local index of the VLAN mode table.
TP5 tp5000eVlanModeModuleID	1.3.6.1.4.1.9070.1.2.5.7.1.10.3.1.2	TP5000MODULEID	read-only	Module ID is the name of the physical module (the inventory module ID) in which the current VLAN is defined. Module ID is the name of the physical module. Its value can be one of the following: IMC (2), IOC1 (3), IOC2 (4), IO (5), exp0 (6),... exp9 (15). Module ID is only used to show the name of a physical module. It is not used as an index or sorting key.
I32 tp5000eVlanModePortID	1.3.6.1.4.1.9070.1.2.5.7.1.10.3.1.3	Integer32	read-only	Physical port ID where the current VLAN is defined.
ENA tp5000eVlanModeValue	1.3.6.1.4.1.9070.1.2.5.7.1.10.3.1.4	EnableValue	read-write	VLAN mode for the specified physical port. Value can be Enable or Disable. This parameter can enable or disable all VLANs in this physical port, but setting the physical port VLAN mode to Enable is not enough for an individual VLAN to become active. That individual VLAN must also be enabled (see tp5000eVlanNonfixedVlanPortState and tp5000eVlanFixedVlanPortState).
tp5000eIPv6NonfixedVlanTable	1.3.6.1.4.1.9070.1.2.5.7.1.10.4		not-accessible	Description.
tp5000eIPv6NonfixedVlanEntry	1.3.6.1.4.1.9070.1.2.5.7.1.10.4.1		not-accessible	Description.
I32 tp5000eIPv6NonfixedVlanIndex	1.3.6.1.4.1.9070.1.2.5.7.1.10.4.1.1	Integer32	not-accessible	Description.
U32 tp5000eIPv6NonfixedVlanIfIndex	1.3.6.1.4.1.9070.1.2.5.7.1.10.4.1.2	Unsigned32	read-only	Description.
TP5 tp5000eIPv6NonfixedVlanModuleID	1.3.6.1.4.1.9070.1.2.5.7.1.10.4.1.3	TP5000MODULEID	read-create	Description.
I32 tp5000eIPv6NonfixedVlanPortID	1.3.6.1.4.1.9070.1.2.5.7.1.10.4.1.4	Integer32	read-create	Description.
INT tp5000eIPv6NonfixedVlanId	1.3.6.1.4.1.9070.1.2.5.7.1.10.4.1.5	INTEGER	read-create	Description.
I32 tp5000eIPv6NonfixedVlanPriority	1.3.6.1.4.1.9070.1.2.5.7.1.10.4.1.6	Integer32	read-create	Description.
ADR tp5000eIPv6NonfixedVlanAddr	1.3.6.1.4.1.9070.1.2.5.7.1.10.4.1.7	InetAddressIPv6	read-create	Description.
I32 tp5000eIPv6NonfixedVlanPrefix	1.3.6.1.4.1.9070.1.2.5.7.1.10.4.1.8	Integer32	read-create	Description.
ENA tp5000eIPv6NonfixedVlanState	1.3.6.1.4.1.9070.1.2.5.7.1.10.4.1.9	EnableValue	read-create	Description.
ROW tp5000eIPv6NonfixedVlanRowStatus	1.3.6.1.4.1.9070.1.2.5.7.1.10.4.1.10	RowStatus	read-create	Description.
tp5000eIPv6FixedVlanTable	1.3.6.1.4.1.9070.1.2.5.7.1.10.5		not-accessible	Description.
tp5000eIPv6FixedVlanEntry	1.3.6.1.4.1.9070.1.2.5.7.1.10.5.1		not-accessible	Description.
I32 tp5000eIPv6FixedVlanIndex	1.3.6.1.4.1.9070.1.2.5.7.1.10.5.1.1	Integer32	not-accessible	Description.
INT tp5000eIPv6FixedVlanId	1.3.6.1.4.1.9070.1.2.5.7.1.10.5.1.2	INTEGER	read-write	Description.
I32 tp5000eIPv6FixedVlanPriority	1.3.6.1.4.1.9070.1.2.5.7.1.10.5.1.3	Integer32	read-write	Description.
ADR tp5000eIPv6FixedVlanAddr	1.3.6.1.4.1.9070.1.2.5.7.1.10.5.1.4	InetAddressIPv6	read-write	Description.
I32 tp5000eIPv6FixedVlanPrefix	1.3.6.1.4.1.9070.1.2.5.7.1.10.5.1.5	Integer32	read-write	Description.
ADR tp5000eIPv6FixedVlanDefaultRouter	1.3.6.1.4.1.9070.1.2.5.7.1.10.5.1.6	InetAddressIPv6	read-write	Description.
ENA tp5000eIPv6FixedVlanState	1.3.6.1.4.1.9070.1.2.5.7.1.10.5.1.7	EnableValue	read-write	Description.
tp5000eAlarmNotification	1.3.6.1.4.1.9070.1.2.5.7.1.11
tp5000eNotifyElements	1.3.6.1.4.1.9070.1.2.5.7.1.11.1
TP5 tp5000eNotifyModuleId	1.3.6.1.4.1.9070.1.2.5.7.1.11.1.1	TP5000MODULEID	read-only	Module ID is the name of the physical module that generated the notification.
U32 tp5000eNotifyAlarmEventID	1.3.6.1.4.1.9070.1.2.5.7.1.11.1.2	Unsigned32	read-only	The alarm or event ID of the notification.
U32 tp5000eNotifyIndex	1.3.6.1.4.1.9070.1.2.5.7.1.11.1.3	Unsigned32	read-only	Internal alarm index for a notification.
ALA tp5000eNotifySeverity	1.3.6.1.4.1.9070.1.2.5.7.1.11.1.4	ALARMLEVELTYPE	read-only	Alarm severity: 0 - clear alarm or event 2 - critical alarm (set, if non-transient) 3 - major alarm (set, if non-transient) 4 - minor alarm (set, if non-transient) 5 - report event (set, if non-transient)
TP5 tp5000eNotifyTransient	1.3.6.1.4.1.9070.1.2.5.7.1.11.1.5	TP5000TRANSIENT	read-only	The transient state of an alarm or event. It is either a state event (non-transient) or a transient event (transient).
STR tp5000eNotifyDateTime	1.3.6.1.4.1.9070.1.2.5.7.1.11.1.6	DisplayString	read-only	Date and time of the notification.
STR tp5000eNotifyDescription	1.3.6.1.4.1.9070.1.2.5.7.1.11.1.7	DisplayString	read-only	Description of this alarm or event (from the TP5000 internal alarm/event definition table).
IP tp5000eNotifyClientAddr	1.3.6.1.4.1.9070.1.2.5.7.1.11.1.8	IpAddress	read-only	The IPv4 address of TP5000's PTP client that generated the notification.
U32 tp5000eNotifySequenceNum	1.3.6.1.4.1.9070.1.2.5.7.1.11.1.9	Unsigned32	read-only	The sequence number of a notification. Each notification OID (tp5000TrapAlarm, tp5000TrapEvent, and tp5000ClientNotification) has an independently incrementing sequence number. These are reset when the IMC is rebooted.
STR tp5000eNotifyClientClockID	1.3.6.1.4.1.9070.1.2.5.7.1.11.1.10	DisplayString	read-only	Clock ID of the TP5000's PTP client that generated the notification.
NTF tp5000eTrapAlarm	1.3.6.1.4.1.9070.1.2.5.7.1.11.2			TimeProvider 5000 alarm trap for the current notification. It contains the OID and value for module ID, alarm ID, notify index, severity, transient, date and time, severity, descriptions, and sequence number. OID names are defined in tp5000eNotifyElements.
NTF tp5000eTrapEvent	1.3.6.1.4.1.9070.1.2.5.7.1.11.3			TimeProvider 5000 event trap for the current notification. It contains the OIDs and values for module ID, event ID, notify index, severity, transient, date and time, severity, descriptions, and sequence number. OID names are defined in tp5000eNotifyElements.
NTF tp5000eClientNotification	1.3.6.1.4.1.9070.1.2.5.7.1.11.4			TimeProvider 5000 PTP client trap for the current client notification. It contains the OID and value for alarm ID, index, severity, transient, date and time and descriptions, client IP address, client clock id, sequence number. OID names are defined in tp5000eNotifyElements.
NTF tp5000ePtpMgmtEvent	1.3.6.1.4.1.9070.1.2.5.7.1.11.5			Description.
tp5000eIPv6GlobalConfig	1.3.6.1.4.1.9070.1.2.5.7.1.12
snmpIPv4IPv6ManagerTable	1.3.6.1.4.1.9070.1.2.5.7.1.12.1		not-accessible	This table is used to display SNMP manager info, such as managerID, EngineID, manager IP addresses, etc. This table's row only can be added or deleted. The existing row can not be modified.
snmpIPv4IPv6ManagerEntry	1.3.6.1.4.1.9070.1.2.5.7.1.12.1.1		not-accessible	This is an entry in the Manager table.
INT snmpIPv4IPv6ManagerIndex	1.3.6.1.4.1.9070.1.2.5.7.1.12.1.1.1	INTEGER	not-accessible	A unique value for each user entry. This value ranges should be from 1 to 3.
STR snmpIPv4IPv6ManagerID	1.3.6.1.4.1.9070.1.2.5.7.1.12.1.1.2	DisplayString	read-only	SNMP manager ID or name which is used for SNMP v2 or v3 trap or notification.
STR snmpIPv4IPv6ManagerAddress	1.3.6.1.4.1.9070.1.2.5.7.1.12.1.1.3	DisplayString	read-write	SNMP manager IP address. It can be IPv4 IPv6
STR snmpIPv4IPv6ManagerEngineID	1.3.6.1.4.1.9070.1.2.5.7.1.12.1.1.4	DisplayString	read-only	The SNMP management engineID. The format should be 0xDDDDDDDDDDDDDDDD, and minimum length is 14 and maximum length is 32 (including 0x as prefix).
ROW snmpIPv4IPv6ManagerRowStatus	1.3.6.1.4.1.9070.1.2.5.7.1.12.1.1.5	RowStatus	read-write	The row status of SNMP manager table to control row actions. It has the following actions: The status column has six defined values: - `active(1)', which indicates that the conceptual row is available for use by the managed device; - `notInService(2)', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - `notReady(3)', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - `createAndGo(4)', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - `createAndWait(5)', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - `destroy(6)', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row.
tp5000eIPv4IPv6RemoteSyslogTable	1.3.6.1.4.1.9070.1.2.5.7.1.12.2		not-accessible	Remote syslog file control table. It is used to configure a remote syslog server to receive log messages from TP5000K system. Only one remote syslog server is supported at this time.
tp5000eIPv4IPv6RemoteSyslogEntry	1.3.6.1.4.1.9070.1.2.5.7.1.12.2.1		not-accessible	An entry of the remote syslog file control table.
I32 tp5000eIPv4IPv6RemoteSyslogIndex	1.3.6.1.4.1.9070.1.2.5.7.1.12.2.1.1	Integer32	read-only	The local index of the remote syslog file control table. At this time only the index value of 1 is supported.
ENA tp5000eIPv4IPv6RemoteSyslogState	1.3.6.1.4.1.9070.1.2.5.7.1.12.2.1.2	EnableValue	read-write	The remote syslog state control. The setting can be either Enable (1) or Disable (2). Once this is set to Enable, all TP5000E log messages (intended for any of the four built-in logs) will be sent to the remote syslog server.
STR tp5000eIPv4IPv6RemoteSyslogAddr	1.3.6.1.4.1.9070.1.2.5.7.1.12.2.1.3	DisplayString	read-write	The IP address of the remote syslog machine. It can be IPv4 or IPv6
tp5000eIPv4IPv6AuthRADIUSTable	1.3.6.1.4.1.9070.1.2.5.7.1.12.3		not-accessible	This table contains IP addresses and access keys for the Radius authentication server. Radius enable state is set in tp5000eRadiusState outside of this table.
tp5000eIPv4IPv6AuthRADIUSEntry	1.3.6.1.4.1.9070.1.2.5.7.1.12.3.1		not-accessible	An entry of the RADIUS table.
INT tp5000eIPv4IPv6AuthRADIUSIndex	1.3.6.1.4.1.9070.1.2.5.7.1.12.3.1.1	INTEGER	read-only	A local index to the RADIUS table. Currently the system only supports RADIUS index value of 1.
STR tp5000eIPv4IPv6ServerRADIUSIPAddress	1.3.6.1.4.1.9070.1.2.5.7.1.12.3.1.2	DisplayString	read-write	The RADIUS server's IP address. It can be IPv4 or IPv6. An IP address cannot be set up if authRADIUS key value is none.
STR tp5000eIPv4IPv6AuthRADIUSKey	1.3.6.1.4.1.9070.1.2.5.7.1.12.3.1.3	DisplayString	read-write	Authentication key for RADIUS server access.
tp5000eConformance	1.3.6.1.4.1.9070.1.2.5.7.1.13			This subtree contains conformance statements for the Tp5000e MIB module.
tp5000eCompliances	1.3.6.1.4.1.9070.1.2.5.7.1.13.1
tp5000eBasicCompliance	1.3.6.1.4.1.9070.1.2.5.7.1.13.1.1			Description.
tp5000eUocGroups	1.3.6.1.4.1.9070.1.2.5.7.1.13.2
tp5000eLEDGroup	1.3.6.1.4.1.9070.1.2.5.7.1.13.2.1			Description.
tp5000eHWGroup	1.3.6.1.4.1.9070.1.2.5.7.1.13.2.2			Description.
tp5000eModeUpTimeGroup	1.3.6.1.4.1.9070.1.2.5.7.1.13.2.3			Description.
tp5000eModWarmUpGroup	1.3.6.1.4.1.9070.1.2.5.7.1.13.2.4			Description.
tp5000eModStatusGroup	1.3.6.1.4.1.9070.1.2.5.7.1.13.2.5			Description.
tp5000eActiveAlarmGroup	1.3.6.1.4.1.9070.1.2.5.7.1.13.2.6			Description.
tp5000eActiveEventGroup	1.3.6.1.4.1.9070.1.2.5.7.1.13.2.7			Description.
tp5000eAlarmConfigGroup	1.3.6.1.4.1.9070.1.2.5.7.1.13.2.8			Description.
tp5000eGeneralAlarmGroup	1.3.6.1.4.1.9070.1.2.5.7.1.13.2.9			Description.
tp5000eLogFileConfigGroup	1.3.6.1.4.1.9070.1.2.5.7.1.13.2.10			Description.
tp5000eRemoteSyslogGroup	1.3.6.1.4.1.9070.1.2.5.7.1.13.2.11			Description.
tp5000eRedundGroup	1.3.6.1.4.1.9070.1.2.5.7.1.13.2.12			Description.
tp5000eImageGroup	1.3.6.1.4.1.9070.1.2.5.7.1.13.2.13			Description.
tp5000eRebootGroup	1.3.6.1.4.1.9070.1.2.5.7.1.13.2.15			Description.
tp5000eRadiusGroup	1.3.6.1.4.1.9070.1.2.5.7.1.13.2.16			Description.
tp5000eAssetGroup	1.3.6.1.4.1.9070.1.2.5.7.1.13.2.17			Description.
tp5000ePacketServiceGroup	1.3.6.1.4.1.9070.1.2.5.7.1.13.2.18			Description.
tp5000eReferenceStatusGroup	1.3.6.1.4.1.9070.1.2.5.7.1.13.2.19			Description.
tp5000eReferenceConfigGroup	1.3.6.1.4.1.9070.1.2.5.7.1.13.2.20			Description.
tp5000eClockStatusGroup	1.3.6.1.4.1.9070.1.2.5.7.1.13.2.21			Description.
tp5000eClockConfigGroup	1.3.6.1.4.1.9070.1.2.5.7.1.13.2.22			Description.
tp5000eModuleIfGroup	1.3.6.1.4.1.9070.1.2.5.7.1.13.2.23			Description.
tp5000eModuleEntityGroup	1.3.6.1.4.1.9070.1.2.5.7.1.13.2.24			Description.
tp5000eFixedVlanGroup	1.3.6.1.4.1.9070.1.2.5.7.1.13.2.25			Description.
tp5000eNonfixedVlanGroup	1.3.6.1.4.1.9070.1.2.5.7.1.13.2.26			Description.
tp5000eNotifyGroup	1.3.6.1.4.1.9070.1.2.5.7.1.13.2.27			Description.
tp5000eNotificationGroup	1.3.6.1.4.1.9070.1.2.5.7.1.13.2.28			Description.
tp5000eVlanModeGroup	1.3.6.1.4.1.9070.1.2.5.7.1.13.2.29			Description.
tp5000eLastConfigGroup	1.3.6.1.4.1.9070.1.2.5.7.1.13.2.30			Description.
tp5000eIPv6NonfixedVlanGroup	1.3.6.1.4.1.9070.1.2.5.7.1.13.2.31			Description.
tp5000eIPv6FixedVlanGroup	1.3.6.1.4.1.9070.1.2.5.7.1.13.2.32			Description.
tp5000eIPv4IPv6SnmpManagerGroup	1.3.6.1.4.1.9070.1.2.5.7.1.13.2.33			Elements of tp5000eIPv4IPv6SnmpManagerTable
tp5000eIPv4IPv6RemoteSyslogGroup	1.3.6.1.4.1.9070.1.2.5.7.1.13.2.34			Elements of tp5000eIPv4IPv6RemoteSyslogTable
tp5000eIPv4IPv6AuthRADIUSGroup	1.3.6.1.4.1.9070.1.2.5.7.1.13.2.35			Elements of tp5000eIPv4IPv6ServerRADIUSTable

RFC description

Symmetricom TP5000e timing and synchronization equipment vendor-specific MIB for GPS/GNSS and system management.

Start monitoring Symmetricom TP5000e timing/synchronization system (module warm-up/active-alarm status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download TP5000E

What Is TP5000E?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description