All MIBs › SUB10SYSTEMS-MIB
Organization: Sub10 Systems Ltd
Last Updated: 2015-06-03
Category: Enterprise SMI and OID Registration, Radio and Wireless
Description: Manages Sub10 Systems point-to-point microwave radio links, signal quality, and link performance.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is SUB10SYSTEMS-MIB?
SUB10SYSTEMS-MIB is a proprietary module for Sub10 Systems point-to-point microwave radio link equipment used in wireless backhaul networks. It exposes device identity data (unit type, description, hardware serial number, terminal/link/site naming) alongside firmware version and loaded bank information and network addressing. Its monitoring emphasis is on software/hardware status of the radio unit: confirming which firmware version and boot bank is active, verifying the unit's local clock/time is correct, and identifying the physical unit via its serial number and link/site names for fault correlation. It is a self-contained vendor module without notable dependency on other standard MIBs beyond basic SNMP conventions. It is deployed on point-to-point microwave radio terminals used for wireless backhaul links between towers or buildings. Network engineers evaluating or troubleshooting this functionality can download the SUB10SYSTEMS-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in SUB10SYSTEMS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Sub10 Systems point-to-point microwave radio link terminal
Monitoring Examples
An admin polls sub10UnitLclFirmwareVersion and sub10UnitLclFirmwareLoadedBank to confirm which firmware bank is active after an upgrade, cross-referencing sub10UnitLclHWSerialNumber and sub10UnitLclTerminalName to identify the specific radio unit. sub10UnitLclLcTime being out of sync with NTP, or sub10UnitLclIpAddress changing unexpectedly, can reveal a unit that lost time sync or was reconfigured, while sub10Notifications would fire alarms tied to the sub10UnitStatus for that terminal.
What Can Be Monitored
- active firmware version and boot bank
- unit local time
- hardware serial number
- terminal/link/site name
- unit IP address
- unit operational status
This MIB depends on
Related MIBs
Imported Objects
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Counter64 | |
| Integer32 | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 | |
| enterprises |
From SNMPv2-TC
| DateAndTime | |
| DisplayString | |
| RowStatus | |
| TEXTUAL-CONVENTION |
How to Use in IPNetwork Monitor
Example using sub10RadioStatsCurrRxFrms OID:
Select a Sub10 Systems point-to-point microwave radio link terminal (firmware/identity status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type sub10RadioStatsCurrRxFrms into the Find box to locate it in the OID tree, then select it and click OK. The number of Airside frames received over the Radio interface. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter64-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| sub10Compliance | 1.3.6.1.4.1.39003.20.1.1 | The compliance statement for Sub10 entities which implement the SUB10SYSTEMS-MIB. | ||
| sub10Ethernet | 1.3.6.1.4.1.39003.4 | |||
| NTF sub10EthernetAlarm | 1.3.6.1.4.1.39003.0.2 | A measured object relating the Ethernet subsystem has been raised or cleared according to the configured thresholds. For alarm configuration see sub10UnitMgmtAlarmTable. | ||
| sub10EthernetLocalStatus | 1.3.6.1.4.1.39003.4.1.1 | |||
| sub10EthernetMgmt | 1.3.6.1.4.1.39003.4.2 | |||
| sub10EthernetRemoteStatus | 1.3.6.1.4.1.39003.4.1.2 | |||
| sub10EthernetStats | 1.3.6.1.4.1.39003.4.3 | |||
| sub10EthernetStats15mHistory | 1.3.6.1.4.1.39003.4.3.3.1 | |||
| sub10EthernetStats15mHistoryGrp | 1.3.6.1.4.1.39003.20.2.39 | This group defines objects that are members of the sub10EthernetStats15mHistoryGrp group | ||
| sub10EthernetStatsCurrent | 1.3.6.1.4.1.39003.4.3.2 | |||
| sub10EthernetStatsCurrEntry | 1.3.6.1.4.1.39003.4.3.2.1.1 | not-accessible | An entry (row) in the sub10EthernetStatsCurrTable. | |
| sub10EthernetStatsCurrEntryGrp | 1.3.6.1.4.1.39003.20.2.38 | This group defines objects that are members of the sub10EthernetStatsCurrEntryGrp group | ||
| sub10EthernetStatsCurrTable | 1.3.6.1.4.1.39003.4.3.2.1 | not-accessible | This table defines the current stats objects of the ethernet interface. | |
| sub10EthernetStatsGrp | 1.3.6.1.4.1.39003.20.2.37 | This group defines objects that are members of the sub10EthernetStatsGrp group | ||
| sub10EthernetStatsHistory | 1.3.6.1.4.1.39003.4.3.3 | |||
| sub10EthernetStatus | 1.3.6.1.4.1.39003.4.1 | |||
| NUM sub10EthIfIndex | 1.3.6.1.4.1.39003.4.1.1.1.1.6 | Sub10EthInterfaceIndex | not-accessible | A unique value, greater than zero, for each ethernet interface. It is recommended that values are assigned contiguously starting from 1. This is used as an index to the ethernet based enterprise MIB tables and will reflect the number of physical ethernet ports. |
| SUB sub10EthLclDuplex | 1.3.6.1.4.1.39003.4.1.1.1.1.4 | Sub10Duplex | read-only | The duplex operation of the local ethernet interface |
| SUB sub10EthLclLinkStatus | 1.3.6.1.4.1.39003.4.1.1.1.1.1 | Sub10OperStatus | read-only | The status of the ethernet link. Synonymous with interfaces OperState |
| ADR sub10EthLclMacAddress | 1.3.6.1.4.1.39003.4.1.1.1.1.2 | Sub10MacAddress | read-only | The MAC address of the local ethernet interface. Synonymous with interfaces ifPhysAddress |
| SUB sub10EthLclMDI | 1.3.6.1.4.1.39003.4.1.1.1.1.5 | Sub10MDIType | read-only | The MDI/MDIX state of the local ethernet interface |
| U32 sub10EthLclSpeed | 1.3.6.1.4.1.39003.4.1.1.1.1.3 | Unsigned32 | read-only | The estimated speed of the local ethernet interface in bits per second. Synonymous with interfaces ifSpeed |
| sub10EthLclStatusEntry | 1.3.6.1.4.1.39003.4.1.1.1.1 | not-accessible | An entry (row) in the sub10EthLclStatusTable. | |
| sub10EthLclStatusEntryGrp | 1.3.6.1.4.1.39003.20.2.25 | This group defines objects that are members of the sub10EthLclStatusEntryGrp group | ||
| sub10EthLclStatusTable | 1.3.6.1.4.1.39003.4.1.1.1 | not-accessible | This table defines the local status objects of the ethernet interface. | |
| sub10EthMgmtPhy | 1.3.6.1.4.1.39003.4.2.1 | |||
| SUB sub10EthMgmtPhyAutoNeg | 1.3.6.1.4.1.39003.4.2.1.1.1.1 | Sub10State | read-write | Auto-negotiation of ethernet interface parameters. |
| SUB sub10EthMgmtPhyDuplex | 1.3.6.1.4.1.39003.4.2.1.1.1.3 | Sub10Duplex | read-write | The duplex operation of the ethernet interface used only when sub10UnitMgmtPhyAutoNeg=disabled. |
| sub10EthMgmtPhyEntry | 1.3.6.1.4.1.39003.4.2.1.1.1 | not-accessible | An entry (row) in the sub10EthMgmtPhyTable. | |
| sub10EthMgmtPhyEntryGrp | 1.3.6.1.4.1.39003.20.2.27 | This group defines objects that are members of the sub10EthMgmtPhyEntryGrp group | ||
| SUB sub10EthMgmtPhyMDI | 1.3.6.1.4.1.39003.4.2.1.1.1.4 | Sub10MDIType | read-write | The duplex operation of the ethernet interface used only when sub10UnitMgmtPhyAutoNeg=disabled. |
| U32 sub10EthMgmtPhySpeed | 1.3.6.1.4.1.39003.4.2.1.1.1.2 | Unsigned32 | read-write | Speed of the ethernet interface in bits per second used only when sub10UnitMgmtPhyAutoNeg=disabled. |
| sub10EthMgmtPhyTable | 1.3.6.1.4.1.39003.4.2.1.1 | not-accessible | This table defines the status objects of the ethernet interface. | |
| sub10EthMgmtQoS | 1.3.6.1.4.1.39003.4.2.3 | |||
| SUB sub10EthMgmtQoSActiveState | 1.3.6.1.4.1.39003.4.2.3.1 | Sub10State | read-write | This defines if QoS is enabled or disabled. |
| sub10EthMgmtQoSDSCPEntry | 1.3.6.1.4.1.39003.4.2.3.10.1 | not-accessible | An entry (row) in the sub10EthMgmtQoSDSCPMappingTable. | |
| sub10EthMgmtQoSDSCPEntryGrp | 1.3.6.1.4.1.39003.20.2.34 | This group defines objects that are members of the sub10EthMgmtQoSDSCPEntryGrp group | ||
| U32 sub10EthMgmtQoSDSCPIndex | 1.3.6.1.4.1.39003.4.2.3.10.1.1 | Unsigned32 | not-accessible | The sub10EthMgmtQoSDSCPTable index. |
| U32 sub10EthMgmtQoSDSCPMappingNumber | 1.3.6.1.4.1.39003.4.2.3.9 | Unsigned32 | read-only | The number of sub10EthMgmtQoSDSCPMappingTable table entries present on this system. |
| U32 sub10EthMgmtQoSDSCPMarking | 1.3.6.1.4.1.39003.4.2.3.10.1.2 | Unsigned32 | read-write | The DSCP value used as an index to the table. This defines the DSCP value which when egressing through the ethernet interface is placed on the queue specified by sub10EthMgmtQoSVlanQueueIndex. |
| SUB sub10EthMgmtQoSDSCPQueue | 1.3.6.1.4.1.39003.4.2.3.10.1.3 | Sub10QoSQueue | read-write | The queue number in the sub10EthMgmtQoSQTable which identifies the specific queue where the packets tagged with the specific DSCP marking sub10EthMgmtQoSDSCP are inserted. |
| sub10EthMgmtQoSDSCPTable | 1.3.6.1.4.1.39003.4.2.3.10 | not-accessible | This table configures the Quality of Service Differentiated Services Code Point (DSCP) to queue mapping. Multiple DSCPs may be mapped to the same queue but the same DSCP cannot be mapped to more than one queue. This table has a maximum size of 64 with 1 entry per DSCP value. On egress of the ethernet interface all pkts tagged with the specific DSCP marking in the IP header will be inserted onto the specified queue. See sub10EthMgmtQoSQTable for more information on QoS queueing. The number of entries in the table is given by the value of sub10EthMgmtQoSDSCPMappingNumber (maximum 64). | |
| sub10EthMgmtQoSGrp | 1.3.6.1.4.1.39003.20.2.30 | This group defines objects that are members of the sub10EthMgmtQoSGrp group | ||
| INT sub10EthMgmtQoSMode | 1.3.6.1.4.1.39003.4.2.3.2 | INTEGER | read-write | Defines the mode of QoS action to be applied to the QoS queues. qosEthernet: - Traffic is mapped to QoS queues - based on Ethernet protocol - VLANId and/or PCP Bits. - See sub10EthMgmtQoSVlanMappingTable - and sub10EthMgmtQoSPCPMappingTable. qosIPMPLS: - Traffic is mapped to QoS queues - based on IP protocol - DSCP markings and/or MPLS traffic - classes. See sub10EthMgmtQoSDSCPMappingTable and sub10EthMgmtQoSMPLSMappingTable. |
| sub10EthMgmtQoSMPLSEntry | 1.3.6.1.4.1.39003.4.2.3.12.1 | not-accessible | An entry (row) in the sub10EthMgmtQoSMPLSMappingTable. | |
| sub10EthMgmtQoSMPLSEntryGrp | 1.3.6.1.4.1.39003.20.2.35 | This group defines objects that are members of the sub10EthMgmtQoSMPLSEntryGrp group | ||
| U32 sub10EthMgmtQoSMPLSIndex | 1.3.6.1.4.1.39003.4.2.3.12.1.1 | Unsigned32 | not-accessible | The sub10EthMgmtQoSMPLSMappingTable index. |
| U32 sub10EthMgmtQoSMPLSMappingNumber | 1.3.6.1.4.1.39003.4.2.3.11 | Unsigned32 | read-only | The number of sub10EthMgmtQoSMPLSMappingTable table entries present on this system.This is equivelent to the number of MPLS Traffic classes |
| SUB sub10EthMgmtQoSMPLSQueue | 1.3.6.1.4.1.39003.4.2.3.12.1.3 | Sub10QoSQueue | read-write | The queue number in the sub10EthMgmtQoSQTable which identifies the specific queue where the packets tagged with the specific MPLS Traffic Class sub10EthMgmtQoSMPLSTrafficClass are inserted. |
| sub10EthMgmtQoSMPLSTable | 1.3.6.1.4.1.39003.4.2.3.12 | not-accessible | This table configures the Quality of Service Multi-Protocol Label Switching protocol (MPLS) Traffic Class (TC) to queue mapping. Multiple MPLS TCs may be mapped to the same queue but the same MPLS TC cannot be mapped to more than one queue. This table has a maximum size of 64 with 1 entry per MPLS TC value. On egress of the ethernet interface all pkts tagged with the specific MPLS TC in the IP header will be inserted onto the specified queue. See sub10EthMgmtQoSQTable for more information on QoS queueing. The number of entries in the table is given by the value of sub10EthMgmtQoSMPLSMappingNumber (maximum 8). | |
| U32 sub10EthMgmtQoSMPLSTrafficClass | 1.3.6.1.4.1.39003.4.2.3.12.1.2 | Unsigned32 | read-write | The MPLS Traffic Class value used as an index to the table. This defines the MPLS TC value which when egressing through the ethernet interface is placed on the queue specified by sub10EthMgmtQoSVlanQueueIndex. |
| sub10EthMgmtQoSPCPEntry | 1.3.6.1.4.1.39003.4.2.3.8.1 | not-accessible | An entry (row) in the sub10EthMgmtQoSPCPMappingTable. | |
| sub10EthMgmtQoSPCPEntryGrp | 1.3.6.1.4.1.39003.20.2.33 | This group defines objects that are members of the sub10EthMgmtQoSPCPEntryGrp group | ||
| U32 sub10EthMgmtQoSPCPIndex | 1.3.6.1.4.1.39003.4.2.3.8.1.1 | Unsigned32 | not-accessible | The sub10EthMgmtQoSPCPTable index. This represents the PCP bits priority value. sub10EthMgmtQoSPCPIndex(1)=PCPBit(0) sub10EthMgmtQoSPCPIndex(2)=PCPBit(1) sub10EthMgmtQoSPCPIndex(3)=PCPBit(2) sub10EthMgmtQoSPCPIndex(4)=PCPBit(3) sub10EthMgmtQoSPCPIndex(5)=PCPBit(4) sub10EthMgmtQoSPCPIndex(6)=PCPBit(5) sub10EthMgmtQoSPCPIndex(7)=PCPBit(6) sub10EthMgmtQoSPCPIndex(8)=PCPBit(7) |
| SUB sub10EthMgmtQoSPCPQueue | 1.3.6.1.4.1.39003.4.2.3.8.1.2 | Sub10QoSQueue | read-write | The queue number in the sub10EthMgmtQoSQTable which identifies the specific queue where the packets tagged with the specific PCP bit sub10EthMgmtQoSPCPIndex are inserted. There are up to 8 queues. |
| sub10EthMgmtQoSPCPTable | 1.3.6.1.4.1.39003.4.2.3.8 | not-accessible | This table configures the Quality of Service Priority Code Point (PCP) or Pbits to queue mapping. Multiple PCPs may be mapped to the same queue but the same PCP cannot be mapped to more than one queue. This table has a maximum size of 8 entries with exactly 1 entry per PCP bit. On egress of the ethernet interface all pkts tagged with the specific PCP bit (irrespective of its Vlan Id) is inserted on the specified queue. See sub10EthMgmtQoSQTable for more information on QoS queueing. The number of entries in the table is given by the value of sub10EthMgmtQoSPCPMappingNumber (maximum 8). | |
| INT sub10EthMgmtQoSQCongestionPolicy | 1.3.6.1.4.1.39003.4.2.3.4.1.4 | INTEGER | read-write | The policy used when a queue is congested. |
| U32 sub10EthMgmtQoSQDWRRWeight | 1.3.6.1.4.1.39003.4.2.3.4.1.3 | Unsigned32 | read-write | A percentage weighting factor used to calculate the quantum value used to calculate the starting transmission credit at each visit of the queue scheduler. Only for scheduling type Deficit Weighted Round Robin. sub10EthMgmtQoSQSchedulingType = 'qosDWRR' The weighting is calculated as the ratio of the transmit rate configured as a percentage. The internal implementation of DWRR will calculate the correct quantum based on total bandwidth available. |
| sub10EthMgmtQoSQEntry | 1.3.6.1.4.1.39003.4.2.3.4.1 | not-accessible | An entry (row) in the sub10EthMgmtQoSQTable. | |
| sub10EthMgmtQoSQEntryGrp | 1.3.6.1.4.1.39003.20.2.31 | This group defines objects that are members of the sub10EthMgmtQoSQEntryGrp group | ||
| U32 sub10EthMgmtQoSQIndex | 1.3.6.1.4.1.39003.4.2.3.4.1.1 | Unsigned32 | not-accessible | The queue number used as an index, fixed to 8 standard queues. |
| U32 sub10EthMgmtQoSQLen | 1.3.6.1.4.1.39003.4.2.3.4.1.6 | Unsigned32 | read-only | The current length of the queue expressed in packets. |
| INT sub10EthMgmtQoSQSchedulingType | 1.3.6.1.4.1.39003.4.2.3.4.1.2 | INTEGER | read-write | The scheduling discipline applied to the queue. qosSPQ - Strict Priority Queueing Queues are serviced in strict priority order. Packets on the queue are servicedd and transmitted until either the queue is empty or a packet is found in a higher queue, in the latter case the higher priority queue take precedence. Individual PCP (CoS) bits or DSCP markings in each packet are not observed within the queue and are not therefore transmitted first according to their relative priority. Instead it is possible to map certain VLANs, PCP bits and DSCP marking to certain queues to achieve priority transmission. The mapping of VLAN, PCP bits or DSCP markings to a specific queue are managed using tables : sub10EthMgmtQoSVlanTable sub10EthMgmtQoSPCPTable sub10EthMgmtQoSDSCPTable qosDWRR - Deficit Weighted Round Robin A weighting is allocated to each queue which defines the number of bytes that can be transmitted from that queue in a single visit of the scheduler. This is used to calculate a quantum which is the number of bytes that can always be transmitted in each visit of the scheduler. A deficit counter is also maintained across visits from the scheduler, at each visit the quantum is added to the deficit. This ensures that on average a queue that is not loaded to its intended capacity will utilise the calculated deficit at times when the queue is busy. At startup Deficit counter is initialised to zero. On each visit of the scheduler packets are transmitted according to the following rules... Deficit = Quantum + Deficit. while (Queue not empty and PktLength <= Deficit) Transmit Pkt Deficit = Deficit - PktLength Remaining Deficit is carried forward to the next visit of the scheduler. Effective behaviour of DWRR is as follows: 1. Available bandwidth is shared fairly when queues are not saturated 2. Lower priority saturated queues will transmit at their allocated service rate. 3. Any remaining bandwidth is shared amongst unsaturated queues. NB. In a mixed configuration where some queues are configured as Strict Priority (SP) and some configured as Deficit Weighted Round Robin (DWRR), then queues configured as SP should all be higher in scheduling priority than those configured as DWRR. This is to avoid the lower priority queues having transmission precedence over higher priority queues. |
| U32 sub10EthMgmtQoSQSizeMax | 1.3.6.1.4.1.39003.4.2.3.4.1.5 | Unsigned32 | read-only | The maximum size of the queue expressed in packets. |
| sub10EthMgmtQoSQTable | 1.3.6.1.4.1.39003.4.2.3.4 | not-accessible | This table configures the characteristics of a Quality of Service queue. There are a fixed number of 8 queues in total and therefore 8 entries in this table indexed 1 thru 8. The number of queue entries in the table is given by the value of sub10EthMgmtQoSQNumber. | |
| SUB sub10EthMgmtQoSUntaggedQueue | 1.3.6.1.4.1.39003.4.2.3.3 | Sub10QoSQueue | read-write | This defines the QoS queue where all untagged ethernet frames are placed. Only valid when sub10EthMgmtQoSQType = 'qosEthernet' For tagged frames see sub10EthMgmtQoSVlanMappingTable and sub10EthMgmtQoSPCPMappingTable. |
| sub10EthMgmtQoSVlanEntry | 1.3.6.1.4.1.39003.4.2.3.6.1 | not-accessible | An entry (row) in the sub10EthMgmtQoSVlanMappingTable. | |
| sub10EthMgmtQoSVlanEntryGrp | 1.3.6.1.4.1.39003.20.2.32 | This group defines objects that are members of the sub10EthMgmtQoSVlanEntryGrp group | ||
| SUB sub10EthMgmtQoSVlanId | 1.3.6.1.4.1.39003.4.2.3.6.1.2 | Sub10VlanId | read-write | The vlan id used as an index to the table and which is egressing through the ethernet interface and which should be placed on the queue specified by sub10EthMgmtQoSVlanQueueIndex. |
| U32 sub10EthMgmtQoSVlanIndex | 1.3.6.1.4.1.39003.4.2.3.6.1.1 | Unsigned32 | not-accessible | The sub10EthMgmtQoSVlanMappingTable index. |
| U32 sub10EthMgmtQoSVlanMappingNumber | 1.3.6.1.4.1.39003.4.2.3.5 | Unsigned32 | read-only | The number of sub10EthMgmtQoSVlanMappingTable table entries present on this system. |
| SUB sub10EthMgmtQoSVlanQueue | 1.3.6.1.4.1.39003.4.2.3.6.1.3 | Sub10QoSQueue | read-write | The queue number which identifies the specific queue where the packets that are tagged with the Vlan Id specified in sub10EthMgmtQoSVlanId are inserted. |
| sub10EthMgmtQoSVlanTable | 1.3.6.1.4.1.39003.4.2.3.6 | not-accessible | This table configures the Quality of Service Vlan to queue mapping. Multiple Vlans may be mapped to any queue. On egress of the ethernet interface all pkts tagged with the specific Vlan Id are inserted onto the specified queue. See sub10EthMgmtQoSQTable for more information on QoS queueing. The number of entries in the table is given by the value of sub10EthMgmtQoSVlanNumber. | |
| sub10EthMgmtStats | 1.3.6.1.4.1.39003.4.2.4 | |||
| sub10EthMgmtStatsActiveEntry | 1.3.6.1.4.1.39003.4.2.4.1.1 | not-accessible | An entry in the sub10EthMgmtStatsActiveTable. Each entry represents an object instance of ethernet stats and it's current state. | |
| sub10EthMgmtStatsActiveEntryGrp | 1.3.6.1.4.1.39003.20.2.36 | This group defines objects that are members of the sub10EthMgmtStatsActiveEntryGrp group | ||
| U32 sub10EthMgmtStatsActiveIndex | 1.3.6.1.4.1.39003.4.2.4.1.1.1 | Unsigned32 | not-accessible | The number of ethernet stats objects used as an index to this table. |
| OCT sub10EthMgmtStatsActiveName | 1.3.6.1.4.1.39003.4.2.4.1.1.2 | OCTET STRING | read-only | The stats object name. This is the name of the ethernet stats object in the sub10EthernetStatsCurrent group. |
| SUB sub10EthMgmtStatsActiveState | 1.3.6.1.4.1.39003.4.2.4.1.1.3 | Sub10State | read-write | If set to 'enabled' the statistic is active. |
| sub10EthMgmtStatsActiveTable | 1.3.6.1.4.1.39003.4.2.4.1 | not-accessible | This table maintains an entry for each Ethernet statistic that is enabled and active. | |
| sub10EthMgmtVlan | 1.3.6.1.4.1.39003.4.2.2 | |||
| sub10EthMgmtVlanAllowedEntry | 1.3.6.1.4.1.39003.4.2.2.8.1 | not-accessible | An entry (row) in the sub10UnitMgmtVlanTable. If the rowStatus is set to notInService(2) then the entry is not valid and no columnar objects are returned. | |
| sub10EthMgmtVlanAllowedEntryGrp | 1.3.6.1.4.1.39003.20.2.29 | This group defines objects that are members of the sub10EthMgmtVlanAllowedEntryGrp group | ||
| SUB sub10EthMgmtVlanAllowedId | 1.3.6.1.4.1.39003.4.2.2.8.1.3 | Sub10VlanId | read-write | The vlan id which is allowed to pass through the ethernet interface. Duplicate vlan ids in multiple entries of the table with RowStatus 'active(1) are not allowed and any attempt to set a duplicate active entry will be rejected. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2). |
| U32 sub10EthMgmtVlanAllowedIndex | 1.3.6.1.4.1.39003.4.2.2.8.1.1 | Unsigned32 | not-accessible | The sub10EthMgmtVlanTable index. |
| ROW sub10EthMgmtVlanAllowedRowStatus | 1.3.6.1.4.1.39003.4.2.2.8.1.2 | RowStatus | read-create | The row status of this row. All table rows are fixed in size and as such do not require conceptual row creation. Instead the RowStatus is set to active(1) or notInService(2) which indicates that the row is operationally in use or not. The default value is notInService(2) meaning the entry is not used by default. To make the entry valid with already consistent row objects this object must be set to active(1). If row objects are not yet set to consistent values the row status must first be set to createAndWait(5) after which the row status is set to 'notReady(3)'. When in the 'notReady(3)' state row objects can then be set to consistent values before row status can be set to active(1). To delete the row set this to destroy(6). |
| sub10EthMgmtVlanAllowedTable | 1.3.6.1.4.1.39003.4.2.2.8 | not-accessible | This tables defines the VLANs that are allowed to pass through the ethernet interface. The table is only used when the value of sub10EthMgmtVlanFiltering is enabled. The table only contains an entry if the specific vlan is to be allowed to flow through the interface. If a VLAN is not in the table then the ethernet frame is dropped. If sub10EthMgmtVlanFiltering is enabled this table must contain at least 1 VLAN. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2). | |
| SUB sub10EthMgmtVlanDefaultDEI | 1.3.6.1.4.1.39003.4.2.2.5 | Sub10State | read-write | The default vlan drop eligible indicator used when tagging the default VLAN to all incoming untagged user traffic ingressing the ethernet interface. Only valid when sub10EthMgmtVlanDefaultEnabled and sub10EthMgmtVlanFiltering are enabled. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2). |
| SUB sub10EthMgmtVlanDefaultEnabled | 1.3.6.1.4.1.39003.4.2.2.2 | Sub10State | read-write | Enable Default VLAN tagging and untagging on the ethernet interface. Only valid when sub10EthMgmtVlanFiltering is enabled. Default VAN tagging allows manipulation of untagged traffic ingressing the interface by applying the specified Default VLAN Id, priority and DEI and manipulation of traffic egressing the ethernet interface that is tagged with the Default VLAN by stripping off the VLAN and transmitting as untagged traffic. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2). |
| SUB sub10EthMgmtVlanDefaultId | 1.3.6.1.4.1.39003.4.2.2.3 | Sub10VlanId | read-write | The default vlan id which is tagged to all incoming untagged user traffic ingressing the ethernet interface. The default VLAN is also untagged from all user traffic egressing the ethernet interface. The default VLAN must be present in the allowed VLAN table sub10EthMgmtVlanAllowedTable and is only valid when sub10EthMgmtVlanDefaultEnabled and sub10EthMgmtVlanFiltering are enabled. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2). |
| SUB sub10EthMgmtVlanDefaultPriority | 1.3.6.1.4.1.39003.4.2.2.4 | Sub10VlanPriority | read-write | The default vlan priority used when tagging the default VLAN to all incoming untagged user traffic ingressing the ethernet interface. Only valid when sub10EthMgmtVlanDefaultEnabled and sub10EthMgmtVlanFiltering are enabled. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2). |
| SUB sub10EthMgmtVlanEgressAction | 1.3.6.1.4.1.39003.4.2.2.7 | Sub10VlanTagAction | read-only | The manipulation action used for all ethernet frames being transmitted (egress) out of the ethernet interface. Only if the default VLAN is set sub10EthMgmtVlanDefaultVlanId > 0 and sub10EthMgmtVlanFiltering is enabled. untag - untag all outgoing frames that are tagged with sub10EthMgmtVlanDefaultVlanId. tag - tag all outgoing untagged frames with sub10EthMgmtVlanDefaultVlanId, ,sub10EthMgmtVlanDefaultPriority and sub10EthMgmtVlanDefaultDEI. and priority sub10EthMgmtTagWithVlanPriority. drop - discard the frame, do not forward. This is currently fixed to untag all egressing traffic. |
| SUB sub10EthMgmtVlanFiltering | 1.3.6.1.4.1.39003.4.2.2.1 | Sub10State | read-write | VLAN filtering on the ethernet interface. This applies to user traffic only not management traffic however to enable VLAN filtering a Unit Management VLAN configuration must be set. See sub10UnitMgmtVlan. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2). |
| sub10EthMgmtVlanGrp | 1.3.6.1.4.1.39003.20.2.28 | This group defines objects that are members of the sub10EthMgmtVlanGrp group | ||
| SUB sub10EthMgmtVlanIngressAction | 1.3.6.1.4.1.39003.4.2.2.6 | Sub10VlanTagAction | read-only | The manipulation action used for all ethernet frames being received (ingress) in from the ethernet interface. Only if the default VLAN is set sub10EthMgmtVlanDefaultVlanId > 0 and sub10EthMgmtVlanFiltering is enabled. untag - untag all incoming frames that are tagged with sub10EthMgmtVlanDefaultVlanId. tag - tag all incoming untagged frames with sub10EthMgmtVlanDefaultVlanId, ,sub10EthMgmtVlanDefaultPriority and sub10EthMgmtVlanDefaultDEI. and priority sub10EthMgmtTagWithVlanPriority. drop - discard the frame, do not forward. This is currently fixed to tag all ingressing traffic if a default VLAN is set sub10EthMgmtVlanDefaultVlanId > 0. |
| SUB sub10EthRmtDuplex | 1.3.6.1.4.1.39003.4.1.2.1.1.4 | Sub10Duplex | read-only | The duplex operation of the remote ethernet interface |
| SUB sub10EthRmtLinkStatus | 1.3.6.1.4.1.39003.4.1.2.1.1.1 | Sub10OperStatus | read-only | The status of the remote ethernet interface. Synonymous but not identical with interfaces OperState on the remote unit |
| ADR sub10EthRmtMacAddress | 1.3.6.1.4.1.39003.4.1.2.1.1.2 | Sub10MacAddress | read-only | The MAC address of the remote ethernet interface. Synonymous with interfaces ifPhysAddress on the remote unit. |
| SUB sub10EthRmtMDI | 1.3.6.1.4.1.39003.4.1.2.1.1.5 | Sub10MDIType | read-only | The MDI/MDIX state of the remote ethernet interface |
| U32 sub10EthRmtSpeed | 1.3.6.1.4.1.39003.4.1.2.1.1.3 | Unsigned32 | read-only | The estimated speed of the remote ethernet interface in bits per second. Synonymous with interfaces ifSpeed on the remote unit |
| sub10EthRmtStatusEntry | 1.3.6.1.4.1.39003.4.1.2.1.1 | not-accessible | An entry (row) in the sub10EthRmtStatusTable. | |
| sub10EthRmtStatusEntryGrp | 1.3.6.1.4.1.39003.20.2.26 | This group defines objects that are members of the sub10EthRmtStatusEntryGrp group | ||
| sub10EthRmtStatusTable | 1.3.6.1.4.1.39003.4.1.2.1 | not-accessible | This table defines the remote status objects of the ethernet interface. | |
| sub10EthStats15mHistEntry | 1.3.6.1.4.1.39003.4.3.3.1.2.1 | not-accessible | An entry in the sub10EthStats15mHistTable. Each entry represents 15 minute of performance management data where the first entry with index=1 is the most recent 15 minute interval and the last entry with index=n (up to 96) is the least recent 15 minute interval. The number of valid intervals is sub10EthStats15mHistIntvls. | |
| sub10EthStats15mHistEntryGrp | 1.3.6.1.4.1.39003.20.2.40 | This group defines objects that are members of the sub10EthStats15mHistEntryGrp group | ||
| U32 sub10EthStats15mHistIntvl | 1.3.6.1.4.1.39003.4.3.3.1.2.1.1 | Unsigned32 | not-accessible | The interval number used as an index to this table. Interval numbers start at 1 (the most recent 15 minute interval) and have a maximum value of 96 (the least recent 15 minute interval). |
| U32 sub10EthStats15mHistIntvls | 1.3.6.1.4.1.39003.4.3.3.1.1 | Unsigned32 | read-only | The number of valid table entries in sub10EthStats15mHistTable on this system. There is one entry per 15 minute interval. If the unit has been running for a minimum of 24 hours and collecting valid data then the number of entries will be 96, this represents a total maximum of 24 hours worth of data. |
| C64 sub10EthStats15mHistPkts1024TMax | 1.3.6.1.4.1.39003.4.3.3.1.2.1.32 | Counter64 | read-only | The total number of frames of size 1024 to RX_MAXLEN bytes for receive or 1024 up for transmit on the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats15mHistPkts128T255 | 1.3.6.1.4.1.39003.4.3.3.1.2.1.29 | Counter64 | read-only | The total number of frames of size 128 to 255 bytes received and transmitted on the Ethernet interface in this 15 minute interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats15mHistPkts256T511 | 1.3.6.1.4.1.39003.4.3.3.1.2.1.30 | Counter64 | read-only | The total number of frames of size 256 to 511 bytes received and transmitted on the Ethernet interface in this 15 minute interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats15mHistPkts512T1023 | 1.3.6.1.4.1.39003.4.3.3.1.2.1.31 | Counter64 | read-only | The total number of frames of size 512 to 1023 bytes received and transmitted on the Ethernet interface in this 15 minute interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats15mHistPkts64Octets | 1.3.6.1.4.1.39003.4.3.3.1.2.1.27 | Counter64 | read-only | The total number of 64-byte frames received and transmitted on the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats15mHistPkts65T127 | 1.3.6.1.4.1.39003.4.3.3.1.2.1.28 | Counter64 | read-only | The total number of frames of size 65 to 127 bytes received and transmitted on the Ethernet interface in this 15 minute interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats15mHistRxAlignErrs | 1.3.6.1.4.1.39003.4.3.3.1.2.1.9 | Counter64 | read-only | The number of Alignment coding errors received over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats15mHistRxBcastFrms | 1.3.6.1.4.1.39003.4.3.3.1.2.1.5 | Counter64 | read-only | The number of broadcast frames received over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats15mHistRxCRCErrs | 1.3.6.1.4.1.39003.4.3.3.1.2.1.8 | Counter64 | read-only | The number of CRC errors received over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats15mHistRxFragments | 1.3.6.1.4.1.39003.4.3.3.1.2.1.13 | Counter64 | read-only | The number of frame fragments received over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats15mHistRxGoodFrms | 1.3.6.1.4.1.39003.4.3.3.1.2.1.4 | Counter64 | read-only | The number of good frames received over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats15mHistRxJabberFrms | 1.3.6.1.4.1.39003.4.3.3.1.2.1.11 | Counter64 | read-only | The number of Jabber frames received over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| SUB sub10EthStats15mHistRxMbpsAvg | 1.3.6.1.4.1.39003.4.3.3.1.2.1.35 | Sub10ThroughputMbps | read-only | The average Rx throughput in Mbps in this 15 minute interval. |
| SUB sub10EthStats15mHistRxMbpsMax | 1.3.6.1.4.1.39003.4.3.3.1.2.1.34 | Sub10ThroughputMbps | read-only | The maximum Rx throughput in Mbps in this 15 minute interval. |
| SUB sub10EthStats15mHistRxMbpsMin | 1.3.6.1.4.1.39003.4.3.3.1.2.1.33 | Sub10ThroughputMbps | read-only | The minimum Rx throughput in Mbps in this 15 minute interval. |
| C64 sub10EthStats15mHistRxMcastFrms | 1.3.6.1.4.1.39003.4.3.3.1.2.1.6 | Counter64 | read-only | The number of multicast frames received over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats15mHistRxOctets | 1.3.6.1.4.1.39003.4.3.3.1.2.1.3 | Counter64 | read-only | The number of octets received over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats15mHistRxOversized | 1.3.6.1.4.1.39003.4.3.3.1.2.1.10 | Counter64 | read-only | The number of Oversized frames received over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats15mHistRxPauseFrms | 1.3.6.1.4.1.39003.4.3.3.1.2.1.7 | Counter64 | read-only | The number of Pause frames received over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats15mHistRxSOFOvrns | 1.3.6.1.4.1.39003.4.3.3.1.2.1.14 | Counter64 | read-only | The number of frames with Start of Frame (SOF) Overruns received over the Ethernet interface or were dropped due to FIFO resource limitations in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats15mHistRxUndersized | 1.3.6.1.4.1.39003.4.3.3.1.2.1.12 | Counter64 | read-only | The number of Undersized frames received over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| sub10EthStats15mHistTable | 1.3.6.1.4.1.39003.4.3.3.1.2 | not-accessible | This table maintains a history of Ethernet statistics based on 15 minute intervals. There are a maximum of 96 intervals which represent 24 hours of data. This table along with the 1m and 1d tables provide a history of the performance of the radio interface. This information may then be post processed and used as a troubleshooting tool. An entry in the table represents a 15 minute interval where each interval is synchronised to the clock on the hour. There are up to 96 intervals starting at 1. The number of valid entries in the table is given by the value of sub10EthStats15mHistIntvls of which the minimum is 0 and the maximum is 96 therefore providing up to a maximum of 24 hours of 15 minute interval data. The first entry indexed by 1 represents the most recent completed 15 minute interval. At the end of each interval all entries of 'index' are copied into entry 'index+1'. If the number of valid intervals is 96 then the least recent interval entry is summarised into 24 hour stats and then discarded. | |
| SUB sub10EthStats15mHistTime | 1.3.6.1.4.1.39003.4.3.3.1.2.1.2 | Sub10DateTime | read-only | The local system time when this 15m history entry was created. This represents the end of the 15 minute interval for which the associated stats with the same sub10EthStats15mHistIntvl table index are relevant. |
| C64 sub10EthStats15mHistTxBcastFrms | 1.3.6.1.4.1.39003.4.3.3.1.2.1.17 | Counter64 | read-only | The number of broadcast frames transmitted over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats15mHistTxCollsn | 1.3.6.1.4.1.39003.4.3.3.1.2.1.21 | Counter64 | read-only | The number of Collision frames transmitted over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats15mHistTxCSenseErrs | 1.3.6.1.4.1.39003.4.3.3.1.2.1.26 | Counter64 | read-only | The number of Carrier Sense Errored frames transmitted over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats15mHistTxDeferred | 1.3.6.1.4.1.39003.4.3.3.1.2.1.20 | Counter64 | read-only | The number of Deferred frames transmitted over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats15mHistTxExsvCollsn | 1.3.6.1.4.1.39003.4.3.3.1.2.1.24 | Counter64 | read-only | The number of Excessive Collision for which transmission was abandoned over the Ethernet interface in this 1 minute interval. 5 For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats15mHistTxGoodFrms | 1.3.6.1.4.1.39003.4.3.3.1.2.1.16 | Counter64 | read-only | The number of ethernet frames transmitted over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats15mHistTxLtCollsn | 1.3.6.1.4.1.39003.4.3.3.1.2.1.25 | Counter64 | read-only | The number of Late Collision for which transmission was abandoned over the Ethernet interface in this 15 minute interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| SUB sub10EthStats15mHistTxMbpsAvg | 1.3.6.1.4.1.39003.4.3.3.1.2.1.38 | Sub10ThroughputMbps | read-only | The average Tx throughput in Mbps in this 15 minute interval. |
| SUB sub10EthStats15mHistTxMbpsMax | 1.3.6.1.4.1.39003.4.3.3.1.2.1.37 | Sub10ThroughputMbps | read-only | The maximum Tx throughput in Mbps in this 15 minute interval. |
| SUB sub10EthStats15mHistTxMbpsMin | 1.3.6.1.4.1.39003.4.3.3.1.2.1.36 | Sub10ThroughputMbps | read-only | The minimum Tx throughput in Mbps in this 15 minute interval. |
| C64 sub10EthStats15mHistTxMcastFrms | 1.3.6.1.4.1.39003.4.3.3.1.2.1.18 | Counter64 | read-only | The number of multicast frames transmitted over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats15mHistTxMlplCollsn | 1.3.6.1.4.1.39003.4.3.3.1.2.1.23 | Counter64 | read-only | The number of Multiple Collision frames transmitted over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats15mHistTxOctets | 1.3.6.1.4.1.39003.4.3.3.1.2.1.15 | Counter64 | read-only | The number of octets transmitted over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats15mHistTxPauseFrms | 1.3.6.1.4.1.39003.4.3.3.1.2.1.19 | Counter64 | read-only | The number of Pause frames transmitted over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats15mHistTxSnglCollsn | 1.3.6.1.4.1.39003.4.3.3.1.2.1.22 | Counter64 | read-only | The number of Single Collision frames transmitted over the Ethernet interface in this 15m interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| sub10EthStats1dHistEntry | 1.3.6.1.4.1.39003.4.3.3.2.2.1 | not-accessible | An entry in the sub10EthStats1dHistTable. Each entry represents 1 day of performance management data where the first entry with index=1 is the most recent 1 day interval and the last entry with index=n (up to 30) is the least recent 1 day interval. The number of valid intervals is given by the value of sub10EthStats1dHistIntvls. | |
| sub10EthStats1dHistEntryGrp | 1.3.6.1.4.1.39003.20.2.42 | This group defines objects that are members of the sub10EthStats1dHistEntryGrp group | ||
| U32 sub10EthStats1dHistIntvl | 1.3.6.1.4.1.39003.4.3.3.2.2.1.1 | Unsigned32 | not-accessible | The interval number used as an index to this table. Interval numbers start at 1 (the most recent 1 day interval) and have a maximum value of 30 (the least recent 1 day interval). |
| U32 sub10EthStats1dHistIntvls | 1.3.6.1.4.1.39003.4.3.3.2.1 | Unsigned32 | read-only | The number of valid table entries in sub10EthStats1dHistTable on this system. There is one entry per 1 day interval. If the unit has been running for a minimum of 30 days and collecting valid data then the number of entries will be 30, this represents a total maximum of 30 days worth of data. |
| sub10EthStats1dHistory | 1.3.6.1.4.1.39003.4.3.3.2 | |||
| sub10EthStats1dHistoryGrp | 1.3.6.1.4.1.39003.20.2.41 | This group defines objects that are members of the sub10EthStats1dHistoryGrp group | ||
| C64 sub10EthStats1dHistPkts1024TMax | 1.3.6.1.4.1.39003.4.3.3.2.2.1.32 | Counter64 | read-only | The total number of frames of size 1024 to RX_MAXLEN bytes for receive or 1024 up for transmit on the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats1dHistPkts128T255 | 1.3.6.1.4.1.39003.4.3.3.2.2.1.29 | Counter64 | read-only | The total number of frames of size 128 to 255 bytes received and transmitted on the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats1dHistPkts256T511 | 1.3.6.1.4.1.39003.4.3.3.2.2.1.30 | Counter64 | read-only | The total number of frames of size 256 to 511 bytes received and transmitted on the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats1dHistPkts512T1023 | 1.3.6.1.4.1.39003.4.3.3.2.2.1.31 | Counter64 | read-only | The total number of frames of size 512 to 1023 bytes received and transmitted on the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats1dHistPkts64Octets | 1.3.6.1.4.1.39003.4.3.3.2.2.1.27 | Counter64 | read-only | The total number of 64-byte frames received and transmitted on the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats1dHistPkts65T127 | 1.3.6.1.4.1.39003.4.3.3.2.2.1.28 | Counter64 | read-only | The total number of frames of size 65 to 127 bytes received and transmitted on the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats1dHistRxAlignErrs | 1.3.6.1.4.1.39003.4.3.3.2.2.1.9 | Counter64 | read-only | The number of Alignment coding errors received over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats1dHistRxBcastFrms | 1.3.6.1.4.1.39003.4.3.3.2.2.1.5 | Counter64 | read-only | The number of broadcast frames received over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats1dHistRxCRCErrs | 1.3.6.1.4.1.39003.4.3.3.2.2.1.8 | Counter64 | read-only | The number of CRC errors received over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats1dHistRxFragments | 1.3.6.1.4.1.39003.4.3.3.2.2.1.13 | Counter64 | read-only | The number of frame fragments received over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats1dHistRxGoodFrms | 1.3.6.1.4.1.39003.4.3.3.2.2.1.4 | Counter64 | read-only | The number of good frames received over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats1dHistRxJabberFrms | 1.3.6.1.4.1.39003.4.3.3.2.2.1.11 | Counter64 | read-only | The number of Jabber frames received over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| SUB sub10EthStats1dHistRxMbpsAvg | 1.3.6.1.4.1.39003.4.3.3.2.2.1.35 | Sub10ThroughputMbps | read-only | The average Rx throughput in Mbps in this 1 day interval. |
| SUB sub10EthStats1dHistRxMbpsMax | 1.3.6.1.4.1.39003.4.3.3.2.2.1.34 | Sub10ThroughputMbps | read-only | The maximum Rx throughput in Mbps in this 15 minute interval. |
| SUB sub10EthStats1dHistRxMbpsMin | 1.3.6.1.4.1.39003.4.3.3.2.2.1.33 | Sub10ThroughputMbps | read-only | The minimum Rx throughput in Mbps in this 15 minute interval. |
| C64 sub10EthStats1dHistRxMcastFrms | 1.3.6.1.4.1.39003.4.3.3.2.2.1.6 | Counter64 | read-only | The number of multicast frames received over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats1dHistRxOctets | 1.3.6.1.4.1.39003.4.3.3.2.2.1.3 | Counter64 | read-only | The number of octets received over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats1dHistRxOversized | 1.3.6.1.4.1.39003.4.3.3.2.2.1.10 | Counter64 | read-only | The number of Oversized frames received over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats1dHistRxPauseFrms | 1.3.6.1.4.1.39003.4.3.3.2.2.1.7 | Counter64 | read-only | The number of Pause frames received over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats1dHistRxSOFOvrns | 1.3.6.1.4.1.39003.4.3.3.2.2.1.14 | Counter64 | read-only | The number of frames with Start of Frame (SOF) Overruns received over the Ethernet interface or were dropped due to FIFO resource limitations in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats1dHistRxUndersized | 1.3.6.1.4.1.39003.4.3.3.2.2.1.12 | Counter64 | read-only | The number of Undersized frames received over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| sub10EthStats1dHistTable | 1.3.6.1.4.1.39003.4.3.3.2.2 | not-accessible | This table maintains a history of Radio statistics based on 1 day intervals. There are a maximum of 30 intervals which represent 30 days of data. This table along with the 1m and 15m tables provide a history of the performance of the radio interface. This information may then be post processed and used as a troubleshooting tool. An entry in the table represents a 1 day interval where each interval is synchronised to the clock on the hour. There are up to 30 intervals starting at 1. The number of valid entries in the table is given by the value of sub10EthStats1dHistIntvls of which the minimum is 0 and the maximum is 30 therefore providing up to a maximum of 30 days of 1 day interval data. The first entry indexed by 1 represents the most recent completed 1 day interval. At the end of each interval all entries of 'index' are copied into entry 'index+1'. If the number of valid intervals is 30 then the least recent interval entry is discarded. | |
| SUB sub10EthStats1dHistTime | 1.3.6.1.4.1.39003.4.3.3.2.2.1.2 | Sub10DateTime | read-only | The local system time when this 1d history entry was created. This represents the end of the 1 day interval for which the associated stats with the same sub10EthStats1dHistIntvl table index are relevant. |
| C64 sub10EthStats1dHistTxBcastFrms | 1.3.6.1.4.1.39003.4.3.3.2.2.1.17 | Counter64 | read-only | The number of broadcast frames transmitted over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats1dHistTxCollsn | 1.3.6.1.4.1.39003.4.3.3.2.2.1.21 | Counter64 | read-only | The number of Collision frames transmitted over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats1dHistTxCSenseErrs | 1.3.6.1.4.1.39003.4.3.3.2.2.1.26 | Counter64 | read-only | The number of Carrier Sense Errored frames transmitted over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats1dHistTxDeferred | 1.3.6.1.4.1.39003.4.3.3.2.2.1.20 | Counter64 | read-only | The number of Deferred frames transmitted over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats1dHistTxExsvCollsn | 1.3.6.1.4.1.39003.4.3.3.2.2.1.24 | Counter64 | read-only | The number of Excessive Collision for which transmission was abandoned over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats1dHistTxGoodFrms | 1.3.6.1.4.1.39003.4.3.3.2.2.1.16 | Counter64 | read-only | The number of ethernet frames transmitted over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats1dHistTxLtCollsn | 1.3.6.1.4.1.39003.4.3.3.2.2.1.25 | Counter64 | read-only | The number of Late Collision for which transmission was abandoned over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| SUB sub10EthStats1dHistTxMbpsAvg | 1.3.6.1.4.1.39003.4.3.3.2.2.1.38 | Sub10ThroughputMbps | read-only | The average Tx throughput in Mbps in this 1 day interval. |
| SUB sub10EthStats1dHistTxMbpsMax | 1.3.6.1.4.1.39003.4.3.3.2.2.1.37 | Sub10ThroughputMbps | read-only | The maximum Tx throughput in Mbps in this 1 day interval. |
| SUB sub10EthStats1dHistTxMbpsMin | 1.3.6.1.4.1.39003.4.3.3.2.2.1.36 | Sub10ThroughputMbps | read-only | The minimum Tx throughput in Mbps in this 1 day interval. |
| C64 sub10EthStats1dHistTxMcastFrms | 1.3.6.1.4.1.39003.4.3.3.2.2.1.18 | Counter64 | read-only | The number of multicast frames transmitted over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats1dHistTxMlplCollsn | 1.3.6.1.4.1.39003.4.3.3.2.2.1.23 | Counter64 | read-only | The number of Multiple Collision frames transmitted over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats1dHistTxOctets | 1.3.6.1.4.1.39003.4.3.3.2.2.1.15 | Counter64 | read-only | The number of octets transmitted over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats1dHistTxPauseFrms | 1.3.6.1.4.1.39003.4.3.3.2.2.1.19 | Counter64 | read-only | The number of Pause frames transmitted over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C64 sub10EthStats1dHistTxSnglCollsn | 1.3.6.1.4.1.39003.4.3.3.2.2.1.22 | Counter64 | read-only | The number of Single Collision frames transmitted over the Ethernet interface in this 1 day interval. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C32 sub10EthStatsCurrPkts1024TMax | 1.3.6.1.4.1.39003.4.3.2.1.1.30 | Counter32 | read-only | The total number of frames of size 1024 to RX_MAXLEN bytes for receive or 1024 up for transmit on the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C32 sub10EthStatsCurrPkts128T255 | 1.3.6.1.4.1.39003.4.3.2.1.1.27 | Counter32 | read-only | The total number of frames of size 128 to 255 bytes received and transmitted on the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C32 sub10EthStatsCurrPkts256T511 | 1.3.6.1.4.1.39003.4.3.2.1.1.28 | Counter32 | read-only | The total number of frames of size 256 to 511 bytes received and transmitted on the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C32 sub10EthStatsCurrPkts512T1023 | 1.3.6.1.4.1.39003.4.3.2.1.1.29 | Counter32 | read-only | The total number of frames of size 512 to 1023 bytes received and transmitted on the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C32 sub10EthStatsCurrPkts64Octets | 1.3.6.1.4.1.39003.4.3.2.1.1.25 | Counter32 | read-only | The total number of 64-byte frames received and transmitted on the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C32 sub10EthStatsCurrPkts65T127 | 1.3.6.1.4.1.39003.4.3.2.1.1.26 | Counter32 | read-only | The total number of frames of size 65 to 127 bytes received and transmitted on the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| SUB sub10EthStatsCurrRmtRxMbpsAvg | 1.3.6.1.4.1.39003.4.3.2.1.1.39 | Sub10ThroughputMbps | read-only | The average Rx throughput of the remote unit in Mbps in the last rolling minute. |
| SUB sub10EthStatsCurrRmtTxMbpsAvg | 1.3.6.1.4.1.39003.4.3.2.1.1.40 | Sub10ThroughputMbps | read-only | The average Tx throughput of the remote unit in Mbps in the last rolling minute. |
| C32 sub10EthStatsCurrRxAlignErrs | 1.3.6.1.4.1.39003.4.3.2.1.1.7 | Counter32 | read-only | The number of Alignment coding errors received over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C32 sub10EthStatsCurrRxBcastFrms | 1.3.6.1.4.1.39003.4.3.2.1.1.3 | Counter32 | read-only | The number of broadcast frames received over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C32 sub10EthStatsCurrRxCRCErrs | 1.3.6.1.4.1.39003.4.3.2.1.1.6 | Counter32 | read-only | The number of CRC errors received over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C32 sub10EthStatsCurrRxFragments | 1.3.6.1.4.1.39003.4.3.2.1.1.11 | Counter32 | read-only | The number of frame fragments received over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C32 sub10EthStatsCurrRxGoodFrms | 1.3.6.1.4.1.39003.4.3.2.1.1.2 | Counter32 | read-only | The number of good frames received over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C32 sub10EthStatsCurrRxJabberFrms | 1.3.6.1.4.1.39003.4.3.2.1.1.9 | Counter32 | read-only | The number of Jabber frames received over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| SUB sub10EthStatsCurrRxMbps | 1.3.6.1.4.1.39003.4.3.2.1.1.31 | Sub10ThroughputMbps | read-only | The Rx throughput in Mbps in this second. |
| SUB sub10EthStatsCurrRxMbpsAvg | 1.3.6.1.4.1.39003.4.3.2.1.1.35 | Sub10ThroughputMbps | read-only | The average Rx throughput in Mbps in the last rolling minute. |
| SUB sub10EthStatsCurrRxMbpsMax | 1.3.6.1.4.1.39003.4.3.2.1.1.34 | Sub10ThroughputMbps | read-only | The maximum Rx throughput in Mbps in the last rolling minute. |
| SUB sub10EthStatsCurrRxMbpsMin | 1.3.6.1.4.1.39003.4.3.2.1.1.33 | Sub10ThroughputMbps | read-only | The minimum Rx throughput in Mbps in the last rolling minute. |
| C32 sub10EthStatsCurrRxMcastFrms | 1.3.6.1.4.1.39003.4.3.2.1.1.4 | Counter32 | read-only | The number of multicast frames received over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C32 sub10EthStatsCurrRxOctets | 1.3.6.1.4.1.39003.4.3.2.1.1.1 | Counter32 | read-only | The number of octets received over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C32 sub10EthStatsCurrRxOversized | 1.3.6.1.4.1.39003.4.3.2.1.1.8 | Counter32 | read-only | The number of Oversized frames received over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C32 sub10EthStatsCurrRxPauseFrms | 1.3.6.1.4.1.39003.4.3.2.1.1.5 | Counter32 | read-only | The number of Pause frames received over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C32 sub10EthStatsCurrRxSOFOvrns | 1.3.6.1.4.1.39003.4.3.2.1.1.12 | Counter32 | read-only | The number of frames with Start of Frame (SOF) Overruns received over the Ethernet interface or were dropped due to FIFO resource limitations since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C32 sub10EthStatsCurrRxUndersized | 1.3.6.1.4.1.39003.4.3.2.1.1.10 | Counter32 | read-only | The number of Undersized frames received over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C32 sub10EthStatsCurrTxBcastFrms | 1.3.6.1.4.1.39003.4.3.2.1.1.15 | Counter32 | read-only | The number of broadcast frames transmitted over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C32 sub10EthStatsCurrTxCollsn | 1.3.6.1.4.1.39003.4.3.2.1.1.19 | Counter32 | read-only | The number of Collision frames transmitted over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C32 sub10EthStatsCurrTxCSenseErrs | 1.3.6.1.4.1.39003.4.3.2.1.1.24 | Counter32 | read-only | The number of Carrier Sense Errored frames transmitted over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C32 sub10EthStatsCurrTxDeferred | 1.3.6.1.4.1.39003.4.3.2.1.1.18 | Counter32 | read-only | The number of Deferred frames transmitted over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C32 sub10EthStatsCurrTxExsvCollsn | 1.3.6.1.4.1.39003.4.3.2.1.1.22 | Counter32 | read-only | The number of Excessive Collision for which transmission was abandoned over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C32 sub10EthStatsCurrTxGoodFrms | 1.3.6.1.4.1.39003.4.3.2.1.1.14 | Counter32 | read-only | The number of ethernet frames transmitted over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C32 sub10EthStatsCurrTxLtCollsn | 1.3.6.1.4.1.39003.4.3.2.1.1.23 | Counter32 | read-only | The number of Late Collision for which transmission was abandoned over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| SUB sub10EthStatsCurrTxMbps | 1.3.6.1.4.1.39003.4.3.2.1.1.32 | Sub10ThroughputMbps | read-only | The Tx throughput in Mbps in this second. |
| SUB sub10EthStatsCurrTxMbpsAvg | 1.3.6.1.4.1.39003.4.3.2.1.1.38 | Sub10ThroughputMbps | read-only | The average Tx throughput in Mbps in the last rolling minute. |
| SUB sub10EthStatsCurrTxMbpsMax | 1.3.6.1.4.1.39003.4.3.2.1.1.37 | Sub10ThroughputMbps | read-only | The maximum Tx throughput in Mbps in the last rolling minute. |
| SUB sub10EthStatsCurrTxMbpsMin | 1.3.6.1.4.1.39003.4.3.2.1.1.36 | Sub10ThroughputMbps | read-only | The minimum Tx throughput in Mbps in the last rolling minute. |
| C32 sub10EthStatsCurrTxMcastFrms | 1.3.6.1.4.1.39003.4.3.2.1.1.16 | Counter32 | read-only | The number of multicast frames transmitted over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C32 sub10EthStatsCurrTxMlplCollsn | 1.3.6.1.4.1.39003.4.3.2.1.1.21 | Counter32 | read-only | The number of Multiple Collision frames transmitted over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C32 sub10EthStatsCurrTxOctets | 1.3.6.1.4.1.39003.4.3.2.1.1.13 | Counter32 | read-only | The number of octets transmitted over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C32 sub10EthStatsCurrTxPauseFrms | 1.3.6.1.4.1.39003.4.3.2.1.1.17 | Counter32 | read-only | The number of Pause frames transmitted over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| C32 sub10EthStatsCurrTxSnglCollsn | 1.3.6.1.4.1.39003.4.3.2.1.1.20 | Counter32 | read-only | The number of Single Collision frames transmitted over the Ethernet interface since the last power cycle / reset of the unit. For more information refer to online techical documentation at http://www.ti.com. Product c667xDSP 'Gigabit Ethernet Switch Subsystem for KeyStone Devices User's Guide'. |
| OCT sub10EthStatsTimeElapsed | 1.3.6.1.4.1.39003.4.3.1 | OCTET STRING | read-only | The time that has elapsed from the beginning of the statistical measurement period. This is normally time from just after the last reboot time when the statistics module begins it's calculations. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value. |
| sub10MIBCompliances | 1.3.6.1.4.1.39003.20.1 | |||
| sub10MIBConformance | 1.3.6.1.4.1.39003.20 | |||
| sub10MIBGroups | 1.3.6.1.4.1.39003.20.2 | |||
| sub10Notifications | 1.3.6.1.4.1.39003.0 | |||
| sub10NotificationsGrp | 1.3.6.1.4.1.39003.20.2.1 | This group defines objects that are members of the sub10NotificationsGrp group | ||
| sub10Radio | 1.3.6.1.4.1.39003.5 | |||
| NTF sub10RadioAlarm | 1.3.6.1.4.1.39003.0.3 | A measured object relating the Radio subsystem has been raised or cleared according to the configured thresholds. For alarm configuration see sub10UnitMgmtAlarmTable. | ||
| OCT sub10RadioLclAFER | 1.3.6.1.4.1.39003.5.1.1.9 | OCTET STRING | read-only | The Air Frame Error Ratio in the last second. This is the % of lost air frames based on the UFEC count in the previous second divided by the expected Air Frame Rate(AFR) in 1 second. |
| SUB sub10RadioLclAlignmentMode | 1.3.6.1.4.1.39003.5.1.1.6 | Sub10AlignmentMode | read-only | Alignment mode is modeAlignment(1) if the alignment / reset cap has been removed for > 5sec otherwise modeNormal(0). The alignment mode is managed using sub10RadioMgmtAlignmentMode. |
| SUB sub10RadioLclDataRate | 1.3.6.1.4.1.39003.5.1.1.7 | Sub10RadioDataRate | read-only | The maximum data rate of the Airside interface. |
| SUB sub10RadioLclLinkStatus | 1.3.6.1.4.1.39003.5.1.1.1 | Sub10RadioLinkState | read-only | The status of the local radio link. |
| OCT sub10RadioLclLnkLoss | 1.3.6.1.4.1.39003.5.1.1.5 | OCTET STRING | read-only | The current link loss of the local radio link, measured in dB. |
| SUB sub10RadioLclMWUType | 1.3.6.1.4.1.39003.5.1.1.8 | Sub10MWUType | read-only | The local MWU type |
| SUB sub10RadioLclRxModulationMode | 1.3.6.1.4.1.39003.5.1.1.10 | Sub10ModulationMode | read-only | The current Receive Modulation Mode on the local unit. |
| OCT sub10RadioLclRxPower | 1.3.6.1.4.1.39003.5.1.1.3 | OCTET STRING | read-only | The current receive power of the local radio link, measured in dBm. |
| SUB sub10RadioLclTxModulationMode | 1.3.6.1.4.1.39003.5.1.1.11 | Sub10ModulationMode | read-only | The current Transmit Modulation Mode on the local unit. |
| I32 sub10RadioLclTxPower | 1.3.6.1.4.1.39003.5.1.1.2 | Integer32 | read-only | The current transmit power of the local radio link, measured in dBm. |
| OCT sub10RadioLclVectErr | 1.3.6.1.4.1.39003.5.1.1.4 | OCTET STRING | read-only | The current vector error of the local radio link, measured in dB. |
| sub10RadioLocalStatus | 1.3.6.1.4.1.39003.5.1.1 | |||
| sub10RadioLocalStatusGrp | 1.3.6.1.4.1.39003.20.2.43 | This group defines objects that are members of the sub10RadioLocalStatusGrp group | ||
| sub10RadioMgmt | 1.3.6.1.4.1.39003.5.2 | |||
| SUB sub10RadioMgmtAlignmentMode | 1.3.6.1.4.1.39003.5.2.6 | Sub10AlignmentMode | read-write | Alignment mode is modeAlignment(1) if the alignment / reset cap has been removed for > 5sec otherwise modeNormal(0). The alignment mode can be manually changed by setting this object. |
| SUB sub10RadioMgmtAmod | 1.3.6.1.4.1.39003.5.2.5 | Sub10State | read-write | Adaptive Modulation mode. |
| INT sub10RadioMgmtAPCMode | 1.3.6.1.4.1.39003.5.2.3 | INTEGER | read-write | Automatic Transmit Power Control. The initial setting of transmit power used is defined by sub10RadioMgmtTxPower. If sub10RadioMgmtAPCMode is enabled then the transmit power may then vary according to the RSSI measured from the remote end of the link. The actual transmit power is readable in sub10RadioLclTxPower at the local end and sub10RadioRmtTxPower at the remote end of the link. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2). |
| SUB sub10RadioMgmtDataRate | 1.3.6.1.4.1.39003.5.2.10 | Sub10RadioDataRate | read-write | The maximum data rate of the Airside interface up to the licensed value. |
| sub10RadioMgmtGrp | 1.3.6.1.4.1.39003.20.2.45 | This group defines objects that are members of the sub10RadioMgmtGrp group | ||
| SUB sub10RadioMgmtModulationMode | 1.3.6.1.4.1.39003.5.2.4 | Sub10ModulationMode | read-write | Set the highest order Modulation Mode attempted by Adaptive Modulation. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2). |
| INT sub10RadioMgmtMWUChannelWidth | 1.3.6.1.4.1.39003.5.2.8 | INTEGER | read-write | MWU Channel width. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2). |
| sub10RadioMgmtStats | 1.3.6.1.4.1.39003.5.2.9 | |||
| SUB sub10RadioMgmtStats1dPersist | 1.3.6.1.4.1.39003.5.2.9.1 | Sub10State | read-write | If set to 'stateEnabled(1) the sub10RadioStats1dHistTable objects are stored and read in on startup. This makes the history non-volatile across unit resets. |
| sub10RadioMgmtStatsActiveEntry | 1.3.6.1.4.1.39003.5.2.9.4.1 | not-accessible | An entry in the sub10RadioMgmtStatsActiveTable. Each entry represents an object instance of Radio stats and it's current state. | |
| sub10RadioMgmtStatsActiveEntryGrp | 1.3.6.1.4.1.39003.20.2.47 | This group defines objects that are members of the sub10RadioMgmtStatsActiveEntryGrp group | ||
| U32 sub10RadioMgmtStatsActiveIndex | 1.3.6.1.4.1.39003.5.2.9.4.1.1 | Unsigned32 | not-accessible | The number of Radio stats objects used as an index to this table. |
| OCT sub10RadioMgmtStatsActiveName | 1.3.6.1.4.1.39003.5.2.9.4.1.2 | OCTET STRING | read-only | The stats object name. This is the name of the ethernet stats object in the sub10RadioStatsCurrent group. |
| SUB sub10RadioMgmtStatsActiveState | 1.3.6.1.4.1.39003.5.2.9.4.1.3 | Sub10State | read-write | If set to 'enabled' the statistic is active. |
| sub10RadioMgmtStatsActiveTable | 1.3.6.1.4.1.39003.5.2.9.4 | not-accessible | This table maintains an entry for each Radio statistic that is enabled and active. | |
| sub10RadioMgmtStatsGrp | 1.3.6.1.4.1.39003.20.2.46 | This group defines objects that are members of the sub10RadioMgmtStatsGrp group | ||
| SUB sub10RadioMgmtTxPowerLimit | 1.3.6.1.4.1.39003.5.2.1 | Sub10TxPowerLimit | read-write | The configured transmit power of radio link. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2). |
| INT sub10RadioMgmtTxRxFreq | 1.3.6.1.4.1.39003.5.2.2 | INTEGER | read-write | The configured TX/RX frequency pairs of radio link. Each enumerated option represents the TX and RX frequency pair settings in MHz. Options are available for E-Band at channel width 250MHz and 500MHz and E-Band channel width 500MHz. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2). |
| sub10RadioRemoteStatus | 1.3.6.1.4.1.39003.5.1.2 | |||
| sub10RadioRemoteStatusGrp | 1.3.6.1.4.1.39003.20.2.44 | This group defines objects that are members of the sub10RadioRemoteStatusGrp group | ||
| OCT sub10RadioRmtAFER | 1.3.6.1.4.1.39003.5.1.2.8 | OCTET STRING | read-only | The remote unit Air Frame Error Ratio in this second. This is the % of lost air frames based on the UFEC count in the previous second divided by the expected Air Frame Rate(AFR) in 1 second. |
| SUB sub10RadioRmtAlignmentMode | 1.3.6.1.4.1.39003.5.1.2.7 | Sub10AlignmentMode | read-only | The remote radio unit's Alignment mode. Alignment mode is modeAlignment(1) if the alignment / reset cap has been removed for > 5sec otherwise modeNormal(0). |
| SUB sub10RadioRmtLinkStatus | 1.3.6.1.4.1.39003.5.1.2.1 | Sub10RadioLinkState | read-only | The status of the remote radio link. |
| OCT sub10RadioRmtLnkLoss | 1.3.6.1.4.1.39003.5.1.2.5 | OCTET STRING | read-only | The current link loss of the remote radio link, measured in dB. |
| OCT sub10RadioRmtRxPower | 1.3.6.1.4.1.39003.5.1.2.3 | OCTET STRING | read-only | The current receive power of the remote radio link, measured in dBm. |
| I32 sub10RadioRmtTxPower | 1.3.6.1.4.1.39003.5.1.2.2 | Integer32 | read-only | The current transmit power of the remote radio link, measured in dBm. |
| OCT sub10RadioRmtVectErr | 1.3.6.1.4.1.39003.5.1.2.4 | OCTET STRING | read-only | The current vector error of the remote radio link, measured in dB. |
| sub10RadioStats | 1.3.6.1.4.1.39003.5.3 | |||
| C32 sub10RadioStats15mHist8PSKToQPSK | 1.3.6.1.4.1.39003.5.3.3.2.2.1.30 | Counter32 | read-only | The number transitions of Modulation Mode configuration from 8PSK to QPSK in this 15 minute interval. |
| OCT sub10RadioStats15mHistAFERAvg | 1.3.6.1.4.1.39003.5.3.3.2.2.1.33 | OCTET STRING | read-only | The average AFER (Air Frame Error Ratio) in this 15 minute interval. See sub10RadioLclAFER. |
| OCT sub10RadioStats15mHistAFERMax | 1.3.6.1.4.1.39003.5.3.3.2.2.1.32 | OCTET STRING | read-only | The maximum AFER (Air Frame Error Ratio) in this 15 minute interval. See sub10RadioLclAFER. |
| OCT sub10RadioStats15mHistAFERMin | 1.3.6.1.4.1.39003.5.3.3.2.2.1.31 | OCTET STRING | read-only | The minimum AFER (Air Frame Error Ratio) in this 15 minute interval. See sub10RadioLclAFER. |
| sub10RadioStats15mHistEntry | 1.3.6.1.4.1.39003.5.3.3.2.2.1 | not-accessible | An entry in the sub10RadioStats15mHistTable. Each entry represents 15 minutes performance management data where the first entry with index=1 is the most recent 15 minute interval and the last entry with index=n (up to 96) is the least recent 15 minute interval. The number of valid intervals is sub10RadioStats15mHistIntvls. | |
| sub10RadioStats15mHistEntryGrp | 1.3.6.1.4.1.39003.20.2.53 | This group defines objects that are members of the sub10RadioStats15mHistEntryGrp group | ||
| U32 sub10RadioStats15mHistIntvl | 1.3.6.1.4.1.39003.5.3.3.2.2.1.1 | Unsigned32 | not-accessible | The interval number used as an index to this table. Interval numbers start at 1 (the most recent 15 minute interval) and have a maximum value of 96 (the least recent 15 minute interval). |
| U32 sub10RadioStats15mHistIntvls | 1.3.6.1.4.1.39003.5.3.3.2.1 | Unsigned32 | read-only | The number of valid table entries in sub10RadioStats15mHistTable on this system. There is one entry per 15 minute interval. If the unit has been running for a minimum of 24 hours and collecting valid data then the number of entries will be 96, this represents a total maximum of 24 hours worth of data. |
| OCT sub10RadioStats15mHistLnkLossAvg | 1.3.6.1.4.1.39003.5.3.3.2.2.1.14 | OCTET STRING | read-only | The average value that the link loss of the local radio link has reached in this 15 minute interval, measured in dB. |
| OCT sub10RadioStats15mHistLnkLossMax | 1.3.6.1.4.1.39003.5.3.3.2.2.1.13 | OCTET STRING | read-only | The maximum value that the link loss of the local radio link has reached in this 15 minute interval, measured in dB. |
| OCT sub10RadioStats15mHistLnkLossMin | 1.3.6.1.4.1.39003.5.3.3.2.2.1.12 | OCTET STRING | read-only | The minimum value that the link loss of the local radio link has reached in this 15 minute interval, measured in dB. |
| I32 sub10RadioStats15mHistMWUTempAvg | 1.3.6.1.4.1.39003.5.3.3.2.2.1.17 | Integer32 | read-only | The average MWU temperature measured in this 15 minute interval. |
| I32 sub10RadioStats15mHistMWUTempMax | 1.3.6.1.4.1.39003.5.3.3.2.2.1.16 | Integer32 | read-only | The maximum MWU temperature measured in this 15 minute interval. |
| I32 sub10RadioStats15mHistMWUTempMin | 1.3.6.1.4.1.39003.5.3.3.2.2.1.15 | Integer32 | read-only | The minimum MWU temperature measured in this 15 minute interval. |
| sub10RadioStats15mHistory | 1.3.6.1.4.1.39003.5.3.3.2 | |||
| sub10RadioStats15mHistoryGrp | 1.3.6.1.4.1.39003.20.2.52 | This group defines objects that are members of the sub10RadioStats15mHistoryGrp group | ||
| C32 sub10RadioStats15mHistQPSKTo8PSK | 1.3.6.1.4.1.39003.5.3.3.2.2.1.29 | Counter32 | read-only | The number transitions of Modulation Mode configuration from QPSK to 8PSK in this 15 minute interval. |
| C32 sub10RadioStats15mHistRx8PSK | 1.3.6.1.4.1.39003.5.3.3.2.2.1.35 | Counter32 | read-only | The time in seconds that the Rx Modulation Mode was 8PSK in this 15 minute interval. |
| C64 sub10RadioStats15mHistRxBadFrms | 1.3.6.1.4.1.39003.5.3.3.2.2.1.28 | Counter64 | read-only | The count of bad frames detected on the receive side of the Radio interface in this 15 minutes. |
| C64 sub10RadioStats15mHistRxFrms | 1.3.6.1.4.1.39003.5.3.3.2.2.1.22 | Counter64 | read-only | The number of Airside frames received over the Radio interface in this 15 minutes. This is irrespective of whether the Airside frame transmitted contained any ethernet data. |
| C64 sub10RadioStats15mHistRxMgmtPkts | 1.3.6.1.4.1.39003.5.3.3.2.2.1.26 | Counter64 | read-only | The number of Ethernet packets received over the Radio interface in this 15 minutes and which are destined for the management sub-system on this unit. |
| C64 sub10RadioStats15mHistRxPkts | 1.3.6.1.4.1.39003.5.3.3.2.2.1.24 | Counter64 | read-only | The number of Ethernet packets received over the Radio interface in this 15 minutes. This includes all packets whether destined for the management sub-system on this unit or to be sent direct to the Ethernet interface. |
| OCT sub10RadioStats15mHistRxPowerAvg | 1.3.6.1.4.1.39003.5.3.3.2.2.1.8 | OCTET STRING | read-only | The average value that the receive power of the local radio link has reached in this 15 minute interval, measured in dBm. |
| OCT sub10RadioStats15mHistRxPowerMax | 1.3.6.1.4.1.39003.5.3.3.2.2.1.7 | OCTET STRING | read-only | The maximum value that the receive power of the local radio link has reached in this 15 minute interval, measured in dBm. |
| OCT sub10RadioStats15mHistRxPowerMin | 1.3.6.1.4.1.39003.5.3.3.2.2.1.6 | OCTET STRING | read-only | The minimum value that the receive power of the local radio link has reached in this 15 minute interval, measured in dBm. |
| C32 sub10RadioStats15mHistRxQPSK | 1.3.6.1.4.1.39003.5.3.3.2.2.1.34 | Counter32 | read-only | The time in seconds that the Rx Modulation Mode was QPSK in this 15 minute interval. |
| sub10RadioStats15mHistTable | 1.3.6.1.4.1.39003.5.3.3.2.2 | not-accessible | This table maintains a history of Radio statistics based on 15 minute intervals. There are a maximum of 96 intervals which represent 24 hours of data. This table along with the 1m and 1d tables provide a history of the performance of the radio interface. This information may then be post processed and used as a troubleshooting tool. An entry in the table represents a 15 minute interval where each interval is synchronised to the clock on the hour. There are up to 96 intervals starting at 1. The number of valid entries in the table is given by the value of sub10RadioStats15mHistIntvls of which the minimum is 0 and the maximum is 96 therefore providing up to a maximum of 24 hours of 15 minute interval data. The first entry indexed by 1 represents the most recent completed 15 minute interval. At the end of each interval all entries of 'index' are copied into entry 'index+1'. If the number of valid intervals is 96 then the least recent interval entry is summarised into 24 hour stats and then discarded. | |
| SUB sub10RadioStats15mHistTime | 1.3.6.1.4.1.39003.5.3.3.2.2.1.2 | Sub10DateTime | read-only | The local system time when this 15m history entry was created. This represents the end of the 15 minute interval for which the associated stats with the same sub10RadioStats15mHistIntvl table index are relevant. |
| C32 sub10RadioStats15mHistTx8PSK | 1.3.6.1.4.1.39003.5.3.3.2.2.1.37 | Counter32 | read-only | The time in seconds that the Tx Modulation Mode was 8PSK in this 15 minute interval. |
| C64 sub10RadioStats15mHistTxFrms | 1.3.6.1.4.1.39003.5.3.3.2.2.1.23 | Counter64 | read-only | The number of Airside frames transmitted over the Radio interface in this 15 minutes. This is irrespective of whether the Airside frame transmitted contained any ethernet data. |
| C64 sub10RadioStats15mHistTxMgmtPkts | 1.3.6.1.4.1.39003.5.3.3.2.2.1.27 | Counter64 | read-only | The number of Ethernet packets transmitted over the Radio interface which originated from the management sub-system in this 15 minutes. This does not include packets originating from the Ethernet interface. |
| C64 sub10RadioStats15mHistTxPkts | 1.3.6.1.4.1.39003.5.3.3.2.2.1.25 | Counter64 | read-only | The number of Ethernet packets transmitted over the Radio interface which originated from the Ethernet interface in this 15 minutes. This does not include packets originating from the management sub-system. |
| I32 sub10RadioStats15mHistTxPowerAvg | 1.3.6.1.4.1.39003.5.3.3.2.2.1.5 | Integer32 | read-only | The average value that the transmit power of the local radio link has reached in this 15 minute interval, measured in dBm. |
| I32 sub10RadioStats15mHistTxPowerMax | 1.3.6.1.4.1.39003.5.3.3.2.2.1.4 | Integer32 | read-only | The maximum value that the transmit power of the local radio link has reached in this 15 minute interval, measured in dBm. |
| I32 sub10RadioStats15mHistTxPowerMin | 1.3.6.1.4.1.39003.5.3.3.2.2.1.3 | Integer32 | read-only | The minimum value that the transmit power of the local radio link has reached in this 15 minute interval, measured in dBm. |
| C32 sub10RadioStats15mHistTxQPSK | 1.3.6.1.4.1.39003.5.3.3.2.2.1.36 | Counter32 | read-only | The time in seconds that the Tx Modulation Mode was QPSK in this 15 minute interval. |
| OCT sub10RadioStats15mHistVectErrAvg | 1.3.6.1.4.1.39003.5.3.3.2.2.1.11 | OCTET STRING | read-only | The average value that the vector error of the local radio link has reached in this 15 minute interval, measured in dB. |
| OCT sub10RadioStats15mHistVectErrMax | 1.3.6.1.4.1.39003.5.3.3.2.2.1.10 | OCTET STRING | read-only | The maximum value that the vector error of the local radio link has reached in this 15 minute interval, measured in dB. |
| OCT sub10RadioStats15mHistVectErrMin | 1.3.6.1.4.1.39003.5.3.3.2.2.1.9 | OCTET STRING | read-only | The minimum value that the vector error of the local radio link has reached in this 15 minute interval, measured in dB. |
| C64 sub10RadioStats1dHist8PSKToQPSK | 1.3.6.1.4.1.39003.5.3.3.3.2.1.30 | Counter64 | read-only | The number transitions of Modulation Mode configuration from 8PSK to QPSK in this 1 day interval. |
| OCT sub10RadioStats1dHistAFERAvg | 1.3.6.1.4.1.39003.5.3.3.3.2.1.33 | OCTET STRING | read-only | The average AFER (Air Frame Error Ratio) in this 1 day interval. See sub10RadioLclAFER. |
| OCT sub10RadioStats1dHistAFERMax | 1.3.6.1.4.1.39003.5.3.3.3.2.1.32 | OCTET STRING | read-only | The maximum AFER (Air Frame Error Ratio) in this 1 day interval. See sub10RadioLclAFER. |
| OCT sub10RadioStats1dHistAFERMin | 1.3.6.1.4.1.39003.5.3.3.3.2.1.31 | OCTET STRING | read-only | The minimum AFER (Air Frame Error Ratio) in this 1 day interval. See sub10RadioLclAFER. |
| sub10RadioStats1dHistEntry | 1.3.6.1.4.1.39003.5.3.3.3.2.1 | not-accessible | An entry in the sub10RadioStats1dHistTable. Each entry represents 1 day of performance management data where the first entry with index=1 is the most recent 1 day interval and the last entry with index=n (up to 30) is the least recent 1 day interval. The number of valid intervals is given by the value of sub10RadioStats1dHistIntvls. | |
| sub10RadioStats1dHistEntryGrp | 1.3.6.1.4.1.39003.20.2.55 | This group defines objects that are members of the sub10RadioStats1dHistEntryGrp group | ||
| U32 sub10RadioStats1dHistIntvl | 1.3.6.1.4.1.39003.5.3.3.3.2.1.1 | Unsigned32 | not-accessible | The interval number used as an index to this table. Interval numbers start at 1 (the most recent 1 day interval) and have a maximum value of 24 (the least recent 1 day interval). |
| U32 sub10RadioStats1dHistIntvls | 1.3.6.1.4.1.39003.5.3.3.3.1 | Unsigned32 | read-only | The number of valid table entries in sub10RadioStats1dHistTable on this system. There is one entry per 1 day interval. If the unit has been running for a minimum of 30 days and collecting valid data then the number of entries will be 30, this represents a total maximum of 30 days worth of data. |
| OCT sub10RadioStats1dHistLnkLossAvg | 1.3.6.1.4.1.39003.5.3.3.3.2.1.14 | OCTET STRING | read-only | The average value that the link loss of the local radio link has reached in this day interval, measured in dB. |
| OCT sub10RadioStats1dHistLnkLossMax | 1.3.6.1.4.1.39003.5.3.3.3.2.1.13 | OCTET STRING | read-only | The maximum value that the link loss of the local radio link has reached in this day interval, measured in dB. |
| OCT sub10RadioStats1dHistLnkLossMin | 1.3.6.1.4.1.39003.5.3.3.3.2.1.12 | OCTET STRING | read-only | The minimum value that the link loss of the local radio link has reached in this day interval, measured in dB. |
| I32 sub10RadioStats1dHistMWUTempAvg | 1.3.6.1.4.1.39003.5.3.3.3.2.1.17 | Integer32 | read-only | The average MWU temperature measured in this day interval. |
| I32 sub10RadioStats1dHistMWUTempMax | 1.3.6.1.4.1.39003.5.3.3.3.2.1.16 | Integer32 | read-only | The maximum MWU temperature measured in this day interval. |
| I32 sub10RadioStats1dHistMWUTempMin | 1.3.6.1.4.1.39003.5.3.3.3.2.1.15 | Integer32 | read-only | The minimum MWU temperature measured in this day interval. |
| sub10RadioStats1dHistory | 1.3.6.1.4.1.39003.5.3.3.3 | |||
| sub10RadioStats1dHistoryGrp | 1.3.6.1.4.1.39003.20.2.54 | This group defines objects that are members of the sub10RadioStats1dHistoryGrp group | ||
| C64 sub10RadioStats1dHistQPSKTo8PSK | 1.3.6.1.4.1.39003.5.3.3.3.2.1.29 | Counter64 | read-only | The number transitions of Modulation Mode configuration from QPSK to 8PSK in this 1 day interval. |
| C32 sub10RadioStats1dHistRx8PSK | 1.3.6.1.4.1.39003.5.3.3.3.2.1.35 | Counter32 | read-only | The time in seconds that the Rx Modulation Mode was 8PSK in this 1 day interval. |
| C64 sub10RadioStats1dHistRxBadFrms | 1.3.6.1.4.1.39003.5.3.3.3.2.1.28 | Counter64 | read-only | The count of bad frames detected on the receive side of the Radio interface in this day interval. |
| C64 sub10RadioStats1dHistRxFrms | 1.3.6.1.4.1.39003.5.3.3.3.2.1.22 | Counter64 | read-only | The number of Airside frames received over the Radio interface in this day interval. This is irrespective of whether the Airside frame transmitted contained any ethernet data. |
| C64 sub10RadioStats1dHistRxMgmtPkts | 1.3.6.1.4.1.39003.5.3.3.3.2.1.26 | Counter64 | read-only | The number of Ethernet packets received over the Radio interface in this day interval and which are destined for the management sub-system on this unit. |
| C64 sub10RadioStats1dHistRxPkts | 1.3.6.1.4.1.39003.5.3.3.3.2.1.24 | Counter64 | read-only | The number of Ethernet packets received over the Radio interface in this day interval. This includes all packets whether destined for the management sub-system on this unit or to be sent direct to the Ethernet interface. |
| OCT sub10RadioStats1dHistRxPowerAvg | 1.3.6.1.4.1.39003.5.3.3.3.2.1.8 | OCTET STRING | read-only | The average value that the receive power of the local radio link has reached in this day interval, measured in dBm. |
| OCT sub10RadioStats1dHistRxPowerMax | 1.3.6.1.4.1.39003.5.3.3.3.2.1.7 | OCTET STRING | read-only | The maximum value that the receive power of the local radio link has reached in this day interval, measured in dBm. |
| OCT sub10RadioStats1dHistRxPowerMin | 1.3.6.1.4.1.39003.5.3.3.3.2.1.6 | OCTET STRING | read-only | The minimum value that the receive power of the local radio link has reached in this day interval, measured in dBm. |
| C32 sub10RadioStats1dHistRxQPSK | 1.3.6.1.4.1.39003.5.3.3.3.2.1.34 | Counter32 | read-only | The time in seconds that the Rx Modulation Mode was QPSK in this 1 day interval. |
| sub10RadioStats1dHistTable | 1.3.6.1.4.1.39003.5.3.3.3.2 | not-accessible | This table maintains a history of Radio statistics based on 1 day intervals. There are a maximum of 30 intervals which represent 30 days of data. This table along with the 1m and 15m tables provide a history of the performance of the radio interface. This information may then be post processed and used as a troubleshooting tool. An entry in the table represents a 1 day interval where each interval is synchronised to the clock on the hour. There are up to 30 intervals starting at 1. The number of valid entries in the table is given by the value of sub10RadioStats1dHistIntvls of which the minimum is 0 and the maximum is 30 therefore providing up to a maximum of 30 days of 1 day interval data. The first entry indexed by 1 represents the most recent completed 1 day interval. At the end of each interval all entries of 'index' are copied into entry 'index+1'. If the number of valid intervals is 30 then the least recent interval entry is discarded. | |
| SUB sub10RadioStats1dHistTime | 1.3.6.1.4.1.39003.5.3.3.3.2.1.2 | Sub10DateTime | read-only | The local system time when this 1d history entry was created. This represents the end of the 1 day interval for which the associated stats with the same sub10RadioStats1dHistIntvl table index are relevant. |
| C32 sub10RadioStats1dHistTx8PSK | 1.3.6.1.4.1.39003.5.3.3.3.2.1.37 | Counter32 | read-only | The time in seconds that the Tx Modulation Mode was 8PSK in this 1 day interval. |
| C64 sub10RadioStats1dHistTxFrms | 1.3.6.1.4.1.39003.5.3.3.3.2.1.23 | Counter64 | read-only | The number of Airside frames transmitted over the Radio interface in this day interval. This is irrespective of whether the Airside frame transmitted contained any ethernet data. |
| C64 sub10RadioStats1dHistTxMgmtPkts | 1.3.6.1.4.1.39003.5.3.3.3.2.1.27 | Counter64 | read-only | The number of Ethernet packets transmitted over the Radio interface which originated from the management sub-system in this day interval. This does not include packets originating from the Ethernet interface. |
| C64 sub10RadioStats1dHistTxPkts | 1.3.6.1.4.1.39003.5.3.3.3.2.1.25 | Counter64 | read-only | The number of Ethernet packets transmitted over the Radio interface which originated from the Ethernet interface in this day interval. This does not include packets originating from the management sub-system. |
| I32 sub10RadioStats1dHistTxPowerAvg | 1.3.6.1.4.1.39003.5.3.3.3.2.1.5 | Integer32 | read-only | The average value that the transmit power of the local radio link has reached in this day interval, measured in dBm. |
| I32 sub10RadioStats1dHistTxPowerMax | 1.3.6.1.4.1.39003.5.3.3.3.2.1.4 | Integer32 | read-only | The maximum value that the transmit power of the local radio link has reached in this day interval, measured in dBm. |
| I32 sub10RadioStats1dHistTxPowerMin | 1.3.6.1.4.1.39003.5.3.3.3.2.1.3 | Integer32 | read-only | The minimum value that the transmit power of the local radio link has reached in this day interval, measured in dBm. |
| C32 sub10RadioStats1dHistTxQPSK | 1.3.6.1.4.1.39003.5.3.3.3.2.1.36 | Counter32 | read-only | The time in seconds that the Tx Modulation Mode was QPSK in this 1 day interval. |
| OCT sub10RadioStats1dHistVectErrAvg | 1.3.6.1.4.1.39003.5.3.3.3.2.1.11 | OCTET STRING | read-only | The average value that the vector error of the local radio link has reached in this day interval, measured in dB. |
| OCT sub10RadioStats1dHistVectErrMax | 1.3.6.1.4.1.39003.5.3.3.3.2.1.10 | OCTET STRING | read-only | The maximum value that the vector error of the local radio link has reached in this day interval, measured in dB. |
| OCT sub10RadioStats1dHistVectErrMin | 1.3.6.1.4.1.39003.5.3.3.3.2.1.9 | OCTET STRING | read-only | The minimum value that the vector error of the local radio link has reached in this day interval, measured in dB. |
| C32 sub10RadioStats1mHist8PSKToQPSK | 1.3.6.1.4.1.39003.5.3.3.1.2.1.30 | Counter32 | read-only | The number transitions of Modulation Mode configuration from 8PSK to QPSK in this 1 minute interval. |
| OCT sub10RadioStats1mHistAFERAvg | 1.3.6.1.4.1.39003.5.3.3.1.2.1.33 | OCTET STRING | read-only | The average AFER (Air Frame Error Ratio) in this minute. See sub10RadioLclAFER. |
| OCT sub10RadioStats1mHistAFERMax | 1.3.6.1.4.1.39003.5.3.3.1.2.1.32 | OCTET STRING | read-only | The maximum AFER (Air Frame Error Ratio) in this minute. See sub10RadioLclAFER. |
| OCT sub10RadioStats1mHistAFERMin | 1.3.6.1.4.1.39003.5.3.3.1.2.1.31 | OCTET STRING | read-only | The minimum AFER (Air Frame Error Ratio) in this minute. See sub10RadioLclAFER. |
| sub10RadioStats1mHistEntry | 1.3.6.1.4.1.39003.5.3.3.1.2.1 | not-accessible | An entry in the sub10RadioStats1mHistTable. Each entry represents 1 minute of performance management data where the first entry with index=1 is the most recent 1 minute interval and the last entry with index=n (up to 60) is the least recent 1 minute interval. The number of valid intervals is given by the value of sub10RadioStats1mHistIntvls. | |
| sub10RadioStats1mHistEntryGrp | 1.3.6.1.4.1.39003.20.2.51 | This group defines objects that are members of the sub10RadioStats1mHistEntryGrp group | ||
| U32 sub10RadioStats1mHistIntvl | 1.3.6.1.4.1.39003.5.3.3.1.2.1.1 | Unsigned32 | not-accessible | The interval number used as an index to this table. Interval numbers start at 1 (the most recent 1 minute interval) and have a maximum value of 60 (the least recent 1 minute interval). |
| U32 sub10RadioStats1mHistIntvls | 1.3.6.1.4.1.39003.5.3.3.1.1 | Unsigned32 | read-only | The number of valid table entries in sub10RadioStats1mHistTable on this system. There is one entry per 1 minute interval. If the unit has been running for a minimum of 15 minutes and collecting valid data then the number of entries will be 15, this represents a total maximum of 5 minutes worth of data. |
| OCT sub10RadioStats1mHistLnkLossAvg | 1.3.6.1.4.1.39003.5.3.3.1.2.1.14 | OCTET STRING | read-only | The average value that the link loss of the local radio link has reached in this minute interval, measured in dB. |
| OCT sub10RadioStats1mHistLnkLossMax | 1.3.6.1.4.1.39003.5.3.3.1.2.1.13 | OCTET STRING | read-only | The maximum value that the link loss of the local radio link has reached in this minute interval, measured in dB. |
| OCT sub10RadioStats1mHistLnkLossMin | 1.3.6.1.4.1.39003.5.3.3.1.2.1.12 | OCTET STRING | read-only | The minimum value that the link loss of the local radio link has reached in this minute interval, measured in dB. |
| I32 sub10RadioStats1mHistMWUTempAvg | 1.3.6.1.4.1.39003.5.3.3.1.2.1.17 | Integer32 | read-only | The average MWU temperature measured in this minute interval. |
| I32 sub10RadioStats1mHistMWUTempMax | 1.3.6.1.4.1.39003.5.3.3.1.2.1.16 | Integer32 | read-only | The maximum MWU temperature measured in this minute interval. |
| I32 sub10RadioStats1mHistMWUTempMin | 1.3.6.1.4.1.39003.5.3.3.1.2.1.15 | Integer32 | read-only | The minimum MWU temperature measured in this minute interval. |
| sub10RadioStats1mHistory | 1.3.6.1.4.1.39003.5.3.3.1 | |||
| sub10RadioStats1mHistoryGrp | 1.3.6.1.4.1.39003.20.2.50 | This group defines objects that are members of the sub10RadioStats1mHistoryGrp group | ||
| C32 sub10RadioStats1mHistQPSKTo8PSK | 1.3.6.1.4.1.39003.5.3.3.1.2.1.29 | Counter32 | read-only | The number transitions of Modulation Mode configuration from QPSK to 8PSK in this 1 minute interval. |
| C32 sub10RadioStats1mHistRx8PSK | 1.3.6.1.4.1.39003.5.3.3.1.2.1.35 | Counter32 | read-only | The time in seconds that the Rx Modulation Mode was 8PSK in this 1 minute interval. |
| C64 sub10RadioStats1mHistRxBadFrms | 1.3.6.1.4.1.39003.5.3.3.1.2.1.28 | Counter64 | read-only | The count of bad frames detected on the receive side of the Radio interface in this minute. |
| C64 sub10RadioStats1mHistRxFrms | 1.3.6.1.4.1.39003.5.3.3.1.2.1.22 | Counter64 | read-only | The number of Airside frames received over the Radio interface in this minute. This is irrespective of whether the Airside frame transmitted contained any ethernet data. |
| C64 sub10RadioStats1mHistRxMgmtPkts | 1.3.6.1.4.1.39003.5.3.3.1.2.1.26 | Counter64 | read-only | The number of Ethernet packets received over the Radio interface in this minute and which are destined for the management sub-system on this unit. |
| C64 sub10RadioStats1mHistRxPkts | 1.3.6.1.4.1.39003.5.3.3.1.2.1.24 | Counter64 | read-only | The number of Ethernet packets received over the Radio interface in this minute. This includes all packets whether destined for the management sub-system on this unit or to be sent direct to the Ethernet interface. |
| OCT sub10RadioStats1mHistRxPowerAvg | 1.3.6.1.4.1.39003.5.3.3.1.2.1.8 | OCTET STRING | read-only | The average value that the receive power of the local radio link has reached in this minute interval, measured in dBm. |
| OCT sub10RadioStats1mHistRxPowerMax | 1.3.6.1.4.1.39003.5.3.3.1.2.1.7 | OCTET STRING | read-only | The maximum value that the receive power of the local radio link has reached in this minute interval, measured in dBm. |
| OCT sub10RadioStats1mHistRxPowerMin | 1.3.6.1.4.1.39003.5.3.3.1.2.1.6 | OCTET STRING | read-only | The minimum value that the receive power of the local radio link has reached in this minute interval, measured in dBm. |
| C32 sub10RadioStats1mHistRxQPSK | 1.3.6.1.4.1.39003.5.3.3.1.2.1.34 | Counter32 | read-only | The time in seconds that the Rx Modulation Mode was QPSK in this 1 minute interval. |
| sub10RadioStats1mHistTable | 1.3.6.1.4.1.39003.5.3.3.1.2 | not-accessible | This table maintains a history of Radio statistics based on 1 minute intervals. There are a maximum of 60 intervals which represent 1 hour of data. This table along with the 15m and 1d tables provide a history of the performance of the radio interface. This information may then be post processed and used as a troubleshooting tool. An entry in the table represents a 1 minute interval where each interval is synchronised to the clock on the hour. There are up to 60 intervals starting at 1. The number of valid entries in the table is given by the value of sub10RadioStats1mHistIntvls of which the minimum is 0 and the maximum is 60 therefore providing up to a maximum of 60 minutes of 1 minute interval data. The first entry indexed by 1 represents the most recent completed 1 minute interval. At the end of each interval all entries of 'index' are copied into entry 'index+1'. If the number of valid intervals is at least 15 then these 15 intervals are summarised into 15 minutes stats. At the end of a 60 minute period the least recent interval is discarded to accomodate the next minute interval. | |
| SUB sub10RadioStats1mHistTime | 1.3.6.1.4.1.39003.5.3.3.1.2.1.2 | Sub10DateTime | read-only | The local system time when this 1m history entry was created. This represents the end of the 1 minute interval for which the associated stats with the same sub10RadioStats1mHistIntvl table index are relevant. |
| C32 sub10RadioStats1mHistTx8PSK | 1.3.6.1.4.1.39003.5.3.3.1.2.1.37 | Counter32 | read-only | The time in seconds that the Tx Modulation Mode was 8PSK in this 1 minute interval. |
| C64 sub10RadioStats1mHistTxFrms | 1.3.6.1.4.1.39003.5.3.3.1.2.1.23 | Counter64 | read-only | The number of Airside frames transmitted over the Radio interface in this minute. This is irrespective of whether the Airside frame transmitted contained any ethernet data. |
| C64 sub10RadioStats1mHistTxMgmtPkts | 1.3.6.1.4.1.39003.5.3.3.1.2.1.27 | Counter64 | read-only | The number of Ethernet packets transmitted over the Radio interface which originated from the management sub-system in this minute. This does not include packets originating from the Ethernet interface. |
| C64 sub10RadioStats1mHistTxPkts | 1.3.6.1.4.1.39003.5.3.3.1.2.1.25 | Counter64 | read-only | The number of Ethernet packets transmitted over the Radio interface which originated from the Ethernet interface in this minute. This does not include packets originating from the management sub-system. |
| I32 sub10RadioStats1mHistTxPowerAvg | 1.3.6.1.4.1.39003.5.3.3.1.2.1.5 | Integer32 | read-only | The average value that the transmit power of the local radio link has reached in this minute interval, measured in dBm. |
| I32 sub10RadioStats1mHistTxPowerMax | 1.3.6.1.4.1.39003.5.3.3.1.2.1.4 | Integer32 | read-only | The maximum value that the transmit power of the local radio link has reached in this minute interval, measured in dBm. |
| I32 sub10RadioStats1mHistTxPowerMin | 1.3.6.1.4.1.39003.5.3.3.1.2.1.3 | Integer32 | read-only | The minimum value that the transmit power of the local radio link has reached in this minute interval, measured in dBm. |
| C32 sub10RadioStats1mHistTxQPSK | 1.3.6.1.4.1.39003.5.3.3.1.2.1.36 | Counter32 | read-only | The time in seconds that the Tx Modulation Mode was QPSK in this 1 minute interval. |
| OCT sub10RadioStats1mHistVectErrAvg | 1.3.6.1.4.1.39003.5.3.3.1.2.1.11 | OCTET STRING | read-only | The average value that the vector error of the local radio link has reached in this minute interval, measured in dB. |
| OCT sub10RadioStats1mHistVectErrMax | 1.3.6.1.4.1.39003.5.3.3.1.2.1.10 | OCTET STRING | read-only | The maximum value that the vector error of the local radio link has reached in this minute interval, measured in dB. |
| OCT sub10RadioStats1mHistVectErrMin | 1.3.6.1.4.1.39003.5.3.3.1.2.1.9 | OCTET STRING | read-only | The minimum value that the vector error of the local radio link has reached in this minute interval, measured in dB. |
| C32 sub10RadioStatsCurr8PSKToQPSK | 1.3.6.1.4.1.39003.5.3.2.28 | Counter32 | read-only | The number transitions of Modulation Mode configuration from 8PSK to QPSK since unit reboot. |
| OCT sub10RadioStatsCurrAFERAvg | 1.3.6.1.4.1.39003.5.3.2.31 | OCTET STRING | read-only | The average AFER (Air Frame Error Ratio) in the previous rolling 60 seconds. See sub10RadioLclAFER. |
| OCT sub10RadioStatsCurrAFERMax | 1.3.6.1.4.1.39003.5.3.2.30 | OCTET STRING | read-only | The maximum AFER (Air Frame Error Ratio) in the previous rolling 60 seconds. See sub10RadioLclAFER. |
| OCT sub10RadioStatsCurrAFERMin | 1.3.6.1.4.1.39003.5.3.2.29 | OCTET STRING | read-only | The minimum AFER (Air Frame Error Ratio) in the previous rolling 60 seconds. See sub10RadioLclAFER. |
| sub10RadioStatsCurrent | 1.3.6.1.4.1.39003.5.3.2 | |||
| sub10RadioStatsCurrentGrp | 1.3.6.1.4.1.39003.20.2.49 | This group defines objects that are members of the sub10RadioStatsCurrentGrp group | ||
| OCT sub10RadioStatsCurrLnkLossAvg | 1.3.6.1.4.1.39003.5.3.2.12 | OCTET STRING | read-only | The average value of the link loss of the local radio link measured over the previous rolling 60 seconds. |
| OCT sub10RadioStatsCurrLnkLossMax | 1.3.6.1.4.1.39003.5.3.2.11 | OCTET STRING | read-only | The maximum value that the link loss of the local radio link measured over the previous rolling 60 seconds. |
| OCT sub10RadioStatsCurrLnkLossMin | 1.3.6.1.4.1.39003.5.3.2.10 | OCTET STRING | read-only | The minimum value that the link loss of the local radio link measured over the previous rolling 60 seconds. |
| I32 sub10RadioStatsCurrMWUTempAvg | 1.3.6.1.4.1.39003.5.3.2.26 | Integer32 | read-only | The average MWU temperature measured over the previous rolling 60 seconds. |
| I32 sub10RadioStatsCurrMWUTempMax | 1.3.6.1.4.1.39003.5.3.2.25 | Integer32 | read-only | The maximum MWU temperature measured over the previous rolling 60 seconds. |
| I32 sub10RadioStatsCurrMWUTempMin | 1.3.6.1.4.1.39003.5.3.2.24 | Integer32 | read-only | The minimum MWU temperature measured over the previous rolling 60 seconds. |
| C32 sub10RadioStatsCurrQPSKTo8PSK | 1.3.6.1.4.1.39003.5.3.2.27 | Counter32 | read-only | The number transitions of Modulation Mode configuration from QPSK to 8PSK since unit reboot. |
| OCT sub10RadioStatsCurrRmtAFERAvg | 1.3.6.1.4.1.39003.5.3.2.37 | OCTET STRING | read-only | The average AFER (Air Frame Error Ratio) of the remote unit in the previous rolling 60 seconds. |
| OCT sub10RadioStatsCurrRmtLnkLossAvg | 1.3.6.1.4.1.39003.5.3.2.35 | OCTET STRING | read-only | The average value of the link loss of the remote radio link measured over the previous rolling 60 seconds. |
| I32 sub10RadioStatsCurrRmtMWUTempAvg | 1.3.6.1.4.1.39003.5.3.2.36 | Integer32 | read-only | The average MWU temperature of the remote unit measured over the previous rolling 60 seconds. |
| OCT sub10RadioStatsCurrRmtRxPowerAvg | 1.3.6.1.4.1.39003.5.3.2.33 | OCTET STRING | read-only | The average value of the receive power of the remote radio link measured over the previous rolling 60 seconds. |
| I32 sub10RadioStatsCurrRmtTxPowerAvg | 1.3.6.1.4.1.39003.5.3.2.32 | Integer32 | read-only | The average value of the transmit power of the remote radio link measured over the previous rolling 60 seconds. |
| OCT sub10RadioStatsCurrRmtVectErrAvg | 1.3.6.1.4.1.39003.5.3.2.34 | OCTET STRING | read-only | The average value of the vector error of the remote radio link measured over the previous rolling 60 seconds. |
| C64 sub10RadioStatsCurrRx8PSK | 1.3.6.1.4.1.39003.5.3.2.39 | Counter64 | read-only | The time in seconds that Rx modulation mode has been in 8PSK since last reboot. |
| C64 sub10RadioStatsCurrRxBadFrms | 1.3.6.1.4.1.39003.5.3.2.19 | Counter64 | read-only | The count of bad frames detected on the receive side of the Radio interface. A bad frame could be caused by any one of the following detected errors: UFEC Error Header CRC Error Frame CRC Error Bad header Set to zero on unit reset. |
| C64 sub10RadioStatsCurrRxFrmsEx | 1.3.6.1.4.1.39003.5.3.2.13 | Counter64 | read-only | The number of Airside frames received over the Radio interface. This is irrespective of whether the Airside frame transmitted contained any ethernet data. Set to zero on unit reset. |
| C64 sub10RadioStatsCurrRxMgmtPkts | 1.3.6.1.4.1.39003.5.3.2.17 | Counter64 | read-only | The number of Ethernet packets received over the Radio interface and which are destined for the management sub-system on this unit. Set to zero on unit reset. |
| C64 sub10RadioStatsCurrRxPkts | 1.3.6.1.4.1.39003.5.3.2.15 | Counter64 | read-only | The number of Ethernet packets received over the Radio interface. This includes all packets whether destined for the management sub-system on this unit or to be sent direct to the Ethernet interface. Set to zero on unit reset. |
| OCT sub10RadioStatsCurrRxPowerAvg | 1.3.6.1.4.1.39003.5.3.2.6 | OCTET STRING | read-only | The average value of the receive power of the local radio link measured over the previous rolling 60 seconds. |
| OCT sub10RadioStatsCurrRxPowerMax | 1.3.6.1.4.1.39003.5.3.2.5 | OCTET STRING | read-only | The maximum value that the receive power of the local radio link measured over the previous rolling 60 seconds. |
| OCT sub10RadioStatsCurrRxPowerMin | 1.3.6.1.4.1.39003.5.3.2.4 | OCTET STRING | read-only | The minimum value that the receive power of the local radio link measured over the previous rolling 60 seconds. |
| C64 sub10RadioStatsCurrRxQPSK | 1.3.6.1.4.1.39003.5.3.2.38 | Counter64 | read-only | The time in seconds that Rx modulation mode has been in QPSK since last reboot. |
| C64 sub10RadioStatsCurrTx8PSK | 1.3.6.1.4.1.39003.5.3.2.41 | Counter64 | read-only | The time in seconds that Tx modulation mode has been in 8PSK since last reboot. |
| C64 sub10RadioStatsCurrTxFrms | 1.3.6.1.4.1.39003.5.3.2.14 | Counter64 | read-only | The number of Airside frames transmitted over the Radio interface. This is irrespective of whether the Airside frame transmitted contained any ethernet data. Set to zero on unit reset. |
| C64 sub10RadioStatsCurrTxMgmtPkts | 1.3.6.1.4.1.39003.5.3.2.18 | Counter64 | read-only | The number of Ethernet packets transmitted over the Radio interface which originated from the management sub-system. This does not include packets originating from the Ethernet interface. Set to zero on unit reset. |
| C64 sub10RadioStatsCurrTxPkts | 1.3.6.1.4.1.39003.5.3.2.16 | Counter64 | read-only | The number of Ethernet packets transmitted over the Radio interface which originated from the Ethernet interface. This does not include packets originating from the management sub-system. Set to zero on unit reset. |
| I32 sub10RadioStatsCurrTxPowerAvg | 1.3.6.1.4.1.39003.5.3.2.3 | Integer32 | read-only | The average value of the transmit power of the local radio link measured over the previous rolling 60 seconds. |
| I32 sub10RadioStatsCurrTxPowerMax | 1.3.6.1.4.1.39003.5.3.2.2 | Integer32 | read-only | The maximum value that the transmit power of the local radio link measured over the previous rolling 60 seconds. |
| I32 sub10RadioStatsCurrTxPowerMin | 1.3.6.1.4.1.39003.5.3.2.1 | Integer32 | read-only | The minimum value that the transmit power of the local radio link measured over the previous rolling 60 seconds. |
| C64 sub10RadioStatsCurrTxQPSK | 1.3.6.1.4.1.39003.5.3.2.40 | Counter64 | read-only | The time in seconds that Txmodulation mode has been in QPSK since last reboot. |
| OCT sub10RadioStatsCurrVectErrAvg | 1.3.6.1.4.1.39003.5.3.2.9 | OCTET STRING | read-only | The average value of the vector error of the local radio link measured over the previous rolling 60 seconds. |
| OCT sub10RadioStatsCurrVectErrMax | 1.3.6.1.4.1.39003.5.3.2.8 | OCTET STRING | read-only | The maximum value that the vector error of the local radio link measured over the previous rolling 60 seconds. |
| OCT sub10RadioStatsCurrVectErrMin | 1.3.6.1.4.1.39003.5.3.2.7 | OCTET STRING | read-only | The minimum value that the vector error of the local radio link measured over the previous rolling 60 seconds. |
| sub10RadioStatsGrp | 1.3.6.1.4.1.39003.20.2.48 | This group defines objects that are members of the sub10RadioStatsGrp group | ||
| sub10RadioStatsHistory | 1.3.6.1.4.1.39003.5.3.3 | |||
| OCT sub10RadioStatsTimeElapsed | 1.3.6.1.4.1.39003.5.3.1 | OCTET STRING | read-only | The time that has elapsed from the beginning of the statistical measurement period. This is normally time from just after the last reboot time when the statistics module begins it's calculations. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value. |
| sub10RadioStatus | 1.3.6.1.4.1.39003.5.1 | |||
| sub10Systems | 1.3.6.1.4.1.39003 | Sub10 Systems MIB | ||
| sub10Unit | 1.3.6.1.4.1.39003.3 | |||
| NTF sub10UnitAlarm | 1.3.6.1.4.1.39003.0.1 | A measured object relating the Unit subsystem has been raised or cleared according to the configured thresholds. For alarm configuration see sub10UnitMgmtAlarmTable. | ||
| SUB sub10UnitLclAlarmState | 1.3.6.1.4.1.39003.3.1.1.15.1.2 | Sub10AlarmState | read-only | Internal object to indicate if this alarm is currently in the raised or cleared state. |
| sub10UnitLclAlarmStateEntry | 1.3.6.1.4.1.39003.3.1.1.15.1 | not-accessible | An entry (row) in the sub10UnitLclAlarmStateTable. | |
| sub10UnitLclAlarmStateEntryGrp | 1.3.6.1.4.1.39003.20.2.3 | This group defines objects that are members of the sub10UnitLclAlarmStateEntryGrp group | ||
| SUB sub10UnitLclAlarmStateIndex | 1.3.6.1.4.1.39003.3.1.1.15.1.1 | Sub10AlarmIndex | not-accessible | The sub10UnitLclAlarmStateTable index. The index represents the same index as used in sub10UnitMgmtAlarmTable. The entries in the table correspond to the configured entries in sub10UnitMgmtAlarmTable. |
| sub10UnitLclAlarmStateTable | 1.3.6.1.4.1.39003.3.1.1.15 | not-accessible | The table listing the each active alarm the local unit. An active alarm is where the alarm state is 'raised' at the specific severity level. The entries in the table correspond to the configured entries in sub10UnitMgmtAlarmTable. This table has a single entry per alarm where the index to the table is the same index as the associated Alarm configuration table sub10UnitMgmtAlarmTable. | |
| SUB sub10UnitLclAlarmStateTime | 1.3.6.1.4.1.39003.3.1.1.15.1.3 | Sub10DateTime | read-only | The local date and time when the last Alarm State transition occurred. This object facilitates retrieving all instances of alarms that have been raised or have changed state since a given point in time. Implementations MUST include the offset from UTC, if available. Implementation in environments in which the UTC offset is not available is NOT RECOMMENDED. |
| STR sub10UnitLclDescription | 1.3.6.1.4.1.39003.3.1.1.3 | DisplayString | read-only | The description of the local unit. This is synonymous with MIB-II sysDescr. |
| SUB sub10UnitLclFirmwareLoadedBank | 1.3.6.1.4.1.39003.3.1.1.10 | Sub10FirmwareBank | read-only | Currently loaded bank. The firmware version running in this bank is defined by sub10UnitLclFirmwareVersion. |
| OCT sub10UnitLclFirmwareVersion | 1.3.6.1.4.1.39003.3.1.1.11 | OCTET STRING | read-only | The firmware version currently running on the local unit. This is by definition the firmware loaded into the bank number defined in sub10UnitLclFirmwareLoadedBank. |
| OCT sub10UnitLclFPGAVersion | 1.3.6.1.4.1.39003.3.1.1.18 | OCTET STRING | read-only | The FPGA Version. |
| OCT sub10UnitLclHWSerialNumber | 1.3.6.1.4.1.39003.3.1.1.4 | OCTET STRING | read-only | The hardware serial number of the Local Unit. This also identifies whether the unit is a V-band or E-band product. See sub10UnitLclMWUType. |
| OCT sub10UnitLclIpAddress | 1.3.6.1.4.1.39003.3.1.1.12 | OCTET STRING | read-only | The IP address of the local ethernet interface. |
| OCT sub10UnitLclLinkId | 1.3.6.1.4.1.39003.3.1.1.8 | OCTET STRING | read-only | The administratively assigned identifier for the radio link between the local and remote units. The LinkId must be the same value on both local and remote units. |
| OCT sub10UnitLclLinkName | 1.3.6.1.4.1.39003.3.1.1.7 | OCTET STRING | read-only | The administratively assigned name for the radio link between the local and remote units. This generally identifies geographically the two ends or a radio link within a site or location. This is synonymous with MIB-II sysLocation and can be administratively set via either sysLocation or sub10UnitMgmtLinkName. |
| I32 sub10UnitLclMWUTemperature | 1.3.6.1.4.1.39003.3.1.1.13 | Integer32 | read-only | The modem temperature on the local unit in degrees celsius. |
| SUB sub10UnitLclMWUType | 1.3.6.1.4.1.39003.3.1.1.17 | Sub10MWUType | read-only | The local MWU type |
| SUB sub10UnitLclNTPSyncStatus | 1.3.6.1.4.1.39003.3.1.1.14 | Sub10NTPSyncStatus | read-only | The indication that the systems clock is synchronised with the NTP server. |
| SUB sub10UnitLclRadioDataRate | 1.3.6.1.4.1.39003.3.1.1.16 | Sub10RadioDataRate | read-only | The maximum data rate of the Airside interface. This has the same value as sub10RadioLclDataRate. |
| STR sub10UnitLclSiteName | 1.3.6.1.4.1.39003.3.1.1.9 | DisplayString | read-only | The administratively assigned physical location of the local unit. |
| OCT sub10UnitLclTerminalName | 1.3.6.1.4.1.39003.3.1.1.5 | OCTET STRING | read-only | The administratively assigned name for the unit. This is synonymous with MIB-II sysName and can be administratively set via either sysName or sub10UnitMgmtTerminalName. |
| SUB sub10UnitLclTerminalType | 1.3.6.1.4.1.39003.3.1.1.6 | Sub10TerminalType | read-only | Uniquely identifies the local terminal type A or B. |
| SUB sub10UnitLclTime | 1.3.6.1.4.1.39003.3.1.1.1 | Sub10DateTime | read-only | The local system time as a display string in the format:- YYYY-MM-DD,HH:MM:SS e.g. 2014-5-26,13:30:15 |
| SUB sub10UnitLclUnitType | 1.3.6.1.4.1.39003.3.1.1.2 | Sub10UnitType | read-only | Uniquely identifies the local unit product type |
| sub10UnitLocalStatus | 1.3.6.1.4.1.39003.3.1.1 | |||
| sub10UnitLocalStatusGrp | 1.3.6.1.4.1.39003.20.2.2 | This group defines objects that are members of the sub10UnitLocalStatusGrp group | ||
| sub10UnitMgmt | 1.3.6.1.4.1.39003.3.2 | |||
| sub10UnitMgmtActions | 1.3.6.1.4.1.39003.3.2.20 | |||
| sub10UnitMgmtActionsGrp | 1.3.6.1.4.1.39003.20.2.24 | This group defines objects that are members of the sub10UnitMgmtActionsGrp group | ||
| U32 sub10UnitMgmtAlarmClearIntvls | 1.3.6.1.4.1.39003.3.2.6.1.1.12 | Unsigned32 | read-write | The number of continuous monitoring intervals (see sub10UnitMgmtAlarmMonitorIntvl) where the measured object has crossed the clear threshold before the alarm state is set to cleared. This is intended to reduce the number of alarm state transitions when the measured object value is rapidly changing close to the configured clear threshold. |
| SUB sub10UnitMgmtAlarmClearOper | 1.3.6.1.4.1.39003.3.2.6.1.1.9 | Sub10AlarmOperation | read-write | Type of operation which determines when an alarm is to be cleared. Definition of each type is as follows: lt - Measured objects value is less than clear threshold gt - Measured objects value is greater than clear threshold le - Measured objects value is less than or equal to clear threshold ge - Measured objects value is greater than or equal to clear threshold eq - Measured objects value is equal to clear threshold neq - Measured objects value is not equal to clear threshold The alarm operation defines how to apply the configured thresholds when clearing the alarm. This defines whether the alarm is cleared when the measured object value crosses the threshold from low to high or from high to low or if the measured value hits a certain value or not. Example: Alarm Name Alarm Threshold Clear Operation High Temperature 60 le Low Temperature -30 gt Low Temperature Alarm is cleared when the measured temperature is lower or equal to 60 and Low Temperature cleared when the measured temperature is greater than -30. |
| OCT sub10UnitMgmtAlarmClearThresh | 1.3.6.1.4.1.39003.3.2.6.1.1.10 | OCTET STRING | read-write | The threshold value which the measured object's value crosses causes the alarm to be cleared. The behaviour of a measured value and alarm threshold comparison is defined by the object sub10UnitMgmtAlarmThreshType. The sub10UnitMgmtAlarmClearThresh value may be different to the sub10UnitMgmtAlarmRaiseThresh allowing some hysteresis bewteen raising and clearing of alarms thus avoiding an alarm being continually raised and cleared if the measured value is changing frequently around the threshold. If different raise and clear thresholds are not required then the sub10UnitMgmtAlarmClearThresh and sub10UnitMgmtAlarmRaiseThresh should be set to the same value. |
| SUB sub10UnitMgmtAlarmEnabled | 1.3.6.1.4.1.39003.3.2.6.1.1.16 | Sub10State | read-write | If set to 'enabled' the alarm is enabled. |
| sub10UnitMgmtAlarmEntry | 1.3.6.1.4.1.39003.3.2.6.1.1 | not-accessible | An entry (row) in the sub10UnitMgmtAlarmTable. If the rowStatus is set to notInService(2) then the entry is not valid and no columnar objects are returned. | |
| sub10UnitMgmtAlarmEntryGrp | 1.3.6.1.4.1.39003.20.2.11 | This group defines objects that are members of the sub10UnitMgmtAlarmEntryGrp group | ||
| SUB sub10UnitMgmtAlarmIndex | 1.3.6.1.4.1.39003.3.2.6.1.1.1 | Sub10AlarmIndex | not-accessible | The sub10UnitMgmtAlarmTable index. |
| SUB sub10UnitMgmtAlarmMeasObject | 1.3.6.1.4.1.39003.3.2.6.1.1.5 | Sub10MeasuredObject | read-write | The measured object. This is the object name of the object in the MIB with which the alarm is associated and which the configured thresholds are compared with when deriving the state of the alarm. It is not neccessary for all alarm measurement values to be identified in the MIB since a single alarm may be dependant on checks against entities or objects which are not present in the MIB and therefore do not have an associated OID. In general where an alarm and its thresholds relate to the monitoring of the value of a single MIB object then the OID of that object will be defined here otherwise the value is set to empty string. |
| STR sub10UnitMgmtAlarmMeasObjectVal | 1.3.6.1.4.1.39003.3.2.6.1.1.17 | DisplayString | read-only | The value of sub10UnitMgmtAlarmMeasObject formatted as a displayString which when measured by the alarm subsystem caused an alarm to be either raised or cleared. This is therefore the value of the object which was compared with and found to have crossed the configured threshold causing the alarm to change state. The value is not the current value of the measured object it is the observed value which caused the change in alarm state. |
| U32 sub10UnitMgmtAlarmMeasObjIndex | 1.3.6.1.4.1.39003.3.2.6.1.1.19 | Unsigned32 | read-write | The measured object's index which is a value from 1 and is the instance of the measured object to be monitored. For scalar objects this value is 0 and for non-scalar (or column) objects this value must be 0 or greater and must match the index value defined for the object where the object is defined as a column in a table and the table has an index defined in a certain range. |
| U32 sub10UnitMgmtAlarmMonitorIntvl | 1.3.6.1.4.1.39003.3.2.6.1.1.6 | Unsigned32 | read-write | The interval in seconds when the measured object is to be read and compared with the raise and clear thresholds. An alarm cannot be raised or cleared quicker than the configured interval. Please also see related sub10UnitMgmtAlarmRaiseIntvls and sub10UnitMgmtAlarmClearIntvls objects which also affect when alarms are raised and cleared. This object should be set appropriately for the measured object to be monitored (see sub10UnitMgmtAlarmRaiseMeasObject) and the resulting alarm to be raised and cleared (see sub10UnitMgmtAlarmName). This also affects the forwarding of alarms for example as SNMP notifications. Higher severity alarms may have a shorter interval than those at a lower severity. The correct setting of sub10UnitMgmtAlarmMonitorIntvl and related objects sub10UnitMgmtAlarmRaiseIntvls and sub10UnitMgmtAlarmClearIntvls are important to avoid potential network loading caused by alarm storms. |
| SUB sub10UnitMgmtAlarmName | 1.3.6.1.4.1.39003.3.2.6.1.1.3 | Sub10AlarmName | read-write | The alarm name. This is a short descriptive name for the alarm. Alarm names can be duplicated across entries in order to define the same alarm to be raised and cleared according to different thresholds and different severity levels. If the user defines mutiple alarms with the same name it important to correctly configure severity and thresholds to avoid multiple alarms being generated for the same condition. Fixed alarm names cannot be modified. Fixed alarms are populated automatically in rows 1 to ('sub10UnitMgmtAlarmsUserDefStart'-1) |
| U32 sub10UnitMgmtAlarmRaiseIntvls | 1.3.6.1.4.1.39003.3.2.6.1.1.11 | Unsigned32 | read-write | The number of continuous monitoring intervals (see sub10UnitMgmtAlarmMonitorIntvl) where the measured object has crossed the raise threshold before the alarm state is set to raised. This is intended to reduce the number of alarm state transitions when the measured object value is rapidly changing close to the configured raise threshold. |
| SUB sub10UnitMgmtAlarmRaiseOper | 1.3.6.1.4.1.39003.3.2.6.1.1.7 | Sub10AlarmOperation | read-write | Type of operation which determines when an alarm is to be raised. Definition of each type is as follows: lt - Measured objects value is less than raise threshold gt - Measured objects value is greater than raise threshold le - Measured objects value is less than or equal to raise threshold ge - Measured objects value is greater than or equal to raise threshold eq - Measured objects value is equal to raise threshold neq - Measured objects value is not equal to raise threshold The alarm operation defines how to apply the configured thresholds when raising the alarm. This defines whether the alarm is raised when the measured object value crosses the threshold from low to high or from high to low or if the measured value hits a certain value or not. Example: Alarm Name Alarm Threshold Raise Operation High Temperature 70 gt Low Temperature -30 le High Temperature Alarm is raised when the measured temperature is above 70 and Low Temperature raised when the measured temperature is lower than or equal to -30. |
| OCT sub10UnitMgmtAlarmRaiseThresh | 1.3.6.1.4.1.39003.3.2.6.1.1.8 | OCTET STRING | read-write | The threshold value which the measured object's value crosses causes the alarm to be raised. The behaviour of a measured value and alarm threshold comparison is defined by the object sub10UnitMgmtAlarmThreshType. |
| ROW sub10UnitMgmtAlarmRowStatus | 1.3.6.1.4.1.39003.3.2.6.1.1.2 | RowStatus | read-create | The row status of this row. All table rows are fixed in size and as such do not require conceptual row creation. Instead the RowStatus is set to active(1) or notInService(2) which indicates that the row is operationally in use or not. The default value is notInService(2) meaning the entry is not used by default. To make the entry valid this object must be set to enabled(1), createAndGo(4) or createAndWait(5). To delete the row set this to destroy(6). |
| sub10UnitMgmtAlarms | 1.3.6.1.4.1.39003.3.2.6 | |||
| SUB sub10UnitMgmtAlarmSeverity | 1.3.6.1.4.1.39003.3.2.6.1.1.4 | Sub10AlarmSeverity | read-write | The alarm severity. This is added to each alarm as a parameter. |
| sub10UnitMgmtAlarmsGrp | 1.3.6.1.4.1.39003.20.2.12 | This group defines objects that are members of the sub10UnitMgmtAlarmsGrp group | ||
| OCT sub10UnitMgmtAlarmSmtpAddress | 1.3.6.1.4.1.39003.3.2.6.1.1.14 | OCTET STRING | read-write | The smtp mail address. If set the alarm is suitable formatted and sent to the given mail address. |
| SUB sub10UnitMgmtAlarmsUserDefStart | 1.3.6.1.4.1.39003.3.2.6.2 | Sub10AlarmIndex | read-only | This defines the row index from which point rows in the sub10UnitMgmtAlarmTable can be created and deleted and therefore where user defined alarms start. Any attempt to create or delete a row in the sub10UnitMgmtAlarmTable with an index below this value will fail. |
| sub10UnitMgmtAlarmTable | 1.3.6.1.4.1.39003.3.2.6.1 | not-accessible | The sub10UnitMgmtAlarmTable defines the alarm configuration. The first 'N' rows of the table is reserved for fixed alarms defined by the manufacturer. Fixed alarms cannot be deleted or their names changed, other attributes of a fixed alarm may be modified. The remainder of rows are available for user defined alarms which can be created and deleted. The index value 'N' is defined by 'sub10UnitMgmtAlarmsUserDefStart'. Any attempt to create or delete a row in the table with an index less than value of 'sub10UnitMgmtAlarmsUserDefStart' will be rejected. This table is indexed by alarm index a number ranging from 1 to the maximum number of entries in the alarm table. User defined alarm name and and alarm severity are configurable allowing multiple entries for the same alarm to be raised at different severity levels according to different threshold levels. A user defined alarm can be created with the same name as a fixed alarm if required. For example the fixed alarm 'Rx Power Low' monitors the radio receive power and raises an alarm if the value is less than a certain threshold. A user defined alarm may be created with the same name but a less stringent threshold and a lower seveirty level. This allows same alarms to be raised at increasing severity as the condition causing the alarm worsens. This table allows configuration of threshold passing behavior, threshold values for both raising and clearing the alarms and the perceived severity. The alarm forwarding mechanisms can be defined for example SNMP trap, syslog and SMTP. No validation of thresholds across different entries of the table therefore the administrator must ensure that thresholds are correctly set accordingly for the severity of each alarm. This is particularly important where a single alarm name is configured to be raised at different severity levels. | |
| SUB sub10UnitMgmtAlarmToSNMP | 1.3.6.1.4.1.39003.3.2.6.1.1.18 | Sub10State | read-write | If set to 'enabled' the alarm is forwarded as an SNMP notification / trap. |
| SUB sub10UnitMgmtAlarmToSyslog | 1.3.6.1.4.1.39003.3.2.6.1.1.15 | Sub10State | read-write | If set to 'enabled' the alarm is suitably formatted and sent to syslog. |
| SUB sub10UnitMgmtAlarmType | 1.3.6.1.4.1.39003.3.2.6.1.1.13 | Sub10AlarmType | read-write | The type of the alarm and defines the type of notification (trap) used to inform management entities. |
| STR sub10UnitMgmtContactName | 1.3.6.1.4.1.39003.3.2.1.5 | DisplayString | read-write | The administratively assigned contact for support of the unit. This is synonymous with MIB-II sysContact and sub10UnitLocalStatus sub10UnitLclContactName. |
| DAT sub10UnitMgmtDateTime | 1.3.6.1.4.1.39003.3.2.5.7 | DateAndTime | read-write | The administratively assigned system defined as a standard date-time specification. field octets contents range ----- ------ -------- ----- 1 1-2 year* 0..65536 2 3 month 1..12 3 4 day 1..31 4 5 hour 0..23 5 6 minutes 0..59 6 7 seconds 0..60 (use 60 for leap-second) 7 8 deci-seconds 0..9 8 9 direction from UTC '+' / '-' 9 10 hours from UTC* 0..13 10 11 minutes from UTC 0..59 * Notes: - the value of year is in network-byte order - daylight saving time in New Zealand is +13 For example, Tuesday May 26, 1992 at 1:30:15 PM EDT would be displayed as: 1992-5-26,13:30:15.0,-4:0 Note that if only local time is known, then timezone information (fields 8-10) is not present. |
| sub10UnitMgmtDNS | 1.3.6.1.4.1.39003.3.2.10 | |||
| sub10UnitMgmtDNSEntry | 1.3.6.1.4.1.39003.3.2.10.1.1 | not-accessible | An entry (row) in the sub10UnitMgmtDNSTable. | |
| sub10UnitMgmtDNSEntryGrp | 1.3.6.1.4.1.39003.20.2.20 | This group defines objects that are members of the sub10UnitMgmtDNSEntryGrp group | ||
| OCT sub10UnitMgmtDNServer | 1.3.6.1.4.1.39003.3.2.10.1.1.2 | OCTET STRING | read-write | The administratively assigned DNS server IP for the unit. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2). |
| U32 sub10UnitMgmtDNSIndex | 1.3.6.1.4.1.39003.3.2.10.1.1.1 | Unsigned32 | not-accessible | The sub10UnitMgmtDNSTable index. |
| sub10UnitMgmtDNSTable | 1.3.6.1.4.1.39003.3.2.10.1 | not-accessible | This tables defines the Domain Name Servers. | |
| sub10UnitMgmtEncryption | 1.3.6.1.4.1.39003.3.2.11 | |||
| sub10UnitMgmtEncryptionGrp | 1.3.6.1.4.1.39003.20.2.21 | This group defines objects that are members of the sub10UnitMgmtEncryptionGrp group | ||
| OCT sub10UnitMgmtEncryptKey | 1.3.6.1.4.1.39003.3.2.11.2 | OCTET STRING | read-write | The administratively assigned Encryption key. |
| INT sub10UnitMgmtEncryptMode | 1.3.6.1.4.1.39003.3.2.11.1 | INTEGER | read-write | The administratively assigned License key for the unit. The license key enables capabilities within the unit. The capabilities currently available by the configured license key are readable objects. |
| sub10UnitMgmtFirmware | 1.3.6.1.4.1.39003.3.2.9 | |||
| INT sub10UnitMgmtFirmwareAction | 1.3.6.1.4.1.39003.3.2.9.5 | INTEGER | read-write | The firmware bank action object is used to perform certain actions on a firmware bank. Using this it is possible to reboot the unit, copy banks and upload software to the currently inactive bank. After a Set of this object it's value is always reset to fmwNone(1). The progress of the action may be monitored using a get of the objects 'sub10UnitMgmtFirmwareActStatus' and 'sub10UnitMgmtFirmwareActProgress'. fmwNone(1) - Perform no firmware action unit. fmwReboot(2) - Perform immediate unit reboot of the unit and start the firmware currently loaded in 'sub10UnitMgmtFirmwareSelectBank'. fmwCopyInactiveBank(3) - Copy the firmware currently loaded in 'sub10UnitMgmtFirmwareLoadedBank' to the inactive bank. fmwUploadInactiveBank(4) - Upload the firmware image named by 'sub10UnitMgmtFirmwareUplImage' from the server address 'sub10UnitFirmwareUplServerIp' and load to the inactive bank. |
| I32 sub10UnitMgmtFirmwareActProgress | 1.3.6.1.4.1.39003.3.2.9.12 | Integer32 | read-only | The % progress of firmware action when loading the firmware image to a firmware bank or copying a firmware image from on1 bank to another bank. |
| INT sub10UnitMgmtFirmwareActStatus | 1.3.6.1.4.1.39003.3.2.9.11 | INTEGER | read-only | The status of the firmware bank action which can be repeatedly read using a Get to report the progress of the the action and verify that it has either succeeded or failed. The value is left in the final state after the Firmware Action has completed. |
| sub10UnitMgmtFirmwareBankEntry | 1.3.6.1.4.1.39003.3.2.9.6.1 | not-accessible | An entry (row) in the sub10UnitMgmtFirmwareBankTable. | |
| sub10UnitMgmtFirmwareBankEntryGrp | 1.3.6.1.4.1.39003.20.2.19 | This group defines objects that are members of the sub10UnitMgmtFirmwareBankEntryGrp group | ||
| OCT sub10UnitMgmtFirmwareBankImage | 1.3.6.1.4.1.39003.3.2.9.6.1.3 | OCTET STRING | read-only | The firmware image name currently installed in this bank. |
| SUB sub10UnitMgmtFirmwareBankIndex | 1.3.6.1.4.1.39003.3.2.9.6.1.1 | Sub10FirmwareBank | not-accessible | The sub10UnitMgmtFirmwareBankTable index. |
| sub10UnitMgmtFirmwareBankTable | 1.3.6.1.4.1.39003.3.2.9.6 | not-accessible | This tables contains information regarding the firmware banks. | |
| OCT sub10UnitMgmtFirmwareBankVersion | 1.3.6.1.4.1.39003.3.2.9.6.1.2 | OCTET STRING | read-only | The firmware version currently installed in this bank. |
| OCT sub10UnitMgmtFirmwareBootVersion | 1.3.6.1.4.1.39003.3.2.9.4 | OCTET STRING | read-only | The firmware boot version currently running on the local unit. This is the boot version of the firmware loaded into the bank number defined in sub10UnitMgmtFirmwareLoadedBank. |
| SUB sub10UnitMgmtFirmwareFromBank | 1.3.6.1.4.1.39003.3.2.9.9 | Sub10FirmwareBank | read-only | The bank currently being copied from by the Firmware action sub10UnitMgmtFirmwareAction = fmwCopyInactiveBank(4). |
| sub10UnitMgmtFirmwareGrp | 1.3.6.1.4.1.39003.20.2.18 | This group defines objects that are members of the sub10UnitMgmtFirmwareGrp group | ||
| SUB sub10UnitMgmtFirmwareLoadedBank | 1.3.6.1.4.1.39003.3.2.9.2 | Sub10FirmwareBank | read-only | Currently loaded bank. The firmware version number running in this bank is defined by sub10UnitMgmtFirmwareVersion. |
| SUB sub10UnitMgmtFirmwareSelectBank | 1.3.6.1.4.1.39003.3.2.9.1 | Sub10FirmwareBank | read-write | Currently selected bank which unit uses to boot. |
| SUB sub10UnitMgmtFirmwareToBank | 1.3.6.1.4.1.39003.3.2.9.10 | Sub10FirmwareBank | read-only | The bank currently being uploaded or copied to by the Firmware actions sub10UnitMgmtFirmwareAction = fmwUploadInactiveBank(4) or sub10UnitMgmtFirmwareAction = fmwCopyInactiveBank(4). |
| OCT sub10UnitMgmtFirmwareUplImage | 1.3.6.1.4.1.39003.3.2.9.7 | OCTET STRING | read-write | The firmware image name to be uploaded from the server defined by 'sub10UnitFirmwareUplServerIp' using the firmware action 'sub10UnitFirmwareAction=fmwUpload(4)'. |
| OCT sub10UnitMgmtFirmwareUplSvrIp | 1.3.6.1.4.1.39003.3.2.9.8 | OCTET STRING | read-write | The IP address of the server used to upload the firmware image defined by sub10UnitMgmtFirmwareUplImage. |
| OCT sub10UnitMgmtFirmwareVersion | 1.3.6.1.4.1.39003.3.2.9.3 | OCTET STRING | read-only | The firmware version currently running on the local unit. This is the version of the firmware loaded into the bank number defined in sub10UnitMgmtFirmwareLoadedBank. |
| sub10UnitMgmtIp | 1.3.6.1.4.1.39003.3.2.2 | |||
| OCT sub10UnitMgmtIpAddress | 1.3.6.1.4.1.39003.3.2.2.2 | OCTET STRING | read-write | The administratively assigned IP Address for the management channel. This is reflected in the MIB-II ipAddrTable. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2). |
| OCT sub10UnitMgmtIpDefGateway | 1.3.6.1.4.1.39003.3.2.2.4 | OCTET STRING | read-write | The administratively assigned default gateway for the management channel. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2). |
| SUB sub10UnitMgmtIpDHCP | 1.3.6.1.4.1.39003.3.2.2.5 | Sub10State | read-write | Dynamic Host Control Protocol (DHCP) is enabled or disabled. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2). |
| sub10UnitMgmtIpGrp | 1.3.6.1.4.1.39003.20.2.6 | This group defines objects that are members of the sub10UnitMgmtIpGrp group | ||
| INT sub10UnitMgmtIpMode | 1.3.6.1.4.1.39003.3.2.2.1 | INTEGER | read-write | IP Address configuration is either manually set as ipv4 or ipv6 type addreessing or alternatively can be dynamically assigned automatically using the Dynamic Host Control Protocol (DHCP). IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2). |
| OCT sub10UnitMgmtIpSubnetMask | 1.3.6.1.4.1.39003.3.2.2.3 | OCTET STRING | read-write | The administratively assigned sub-net mask for the management channel. This is reflected in the MIB-II ipAddrTable. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2). |
| sub10UnitMgmtLicense | 1.3.6.1.4.1.39003.3.2.12 | |||
| SUB sub10UnitMgmtLicenseAES | 1.3.6.1.4.1.39003.3.2.12.2 | Sub10State | read-only | Indication if AES encryption is included in the current license key. |
| sub10UnitMgmtLicenseGrp | 1.3.6.1.4.1.39003.20.2.22 | This group defines objects that are members of the sub10UnitMgmtLicenseGrp group | ||
| OCT sub10UnitMgmtLicenseKey | 1.3.6.1.4.1.39003.3.2.12.1 | OCTET STRING | read-write | The administratively assigned License key for the unit. The license key enables capabilities within the unit. The capabilities currently available by the configured license key are readable objects. |
| OCT sub10UnitMgmtLinkId | 1.3.6.1.4.1.39003.3.2.1.3 | OCTET STRING | read-write | The administratively assigned identifier for the radio link between the local and remote units. The LinkId must be the same value on both local and remote units. This is synonymous with sub10UnitLocalStatus sub10UnitLclLinkId. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2). |
| OCT sub10UnitMgmtLinkName | 1.3.6.1.4.1.39003.3.2.1.2 | OCTET STRING | read-write | The administratively assigned name for the radio link between the local and remote units. This generally identifies geographically the two ends or a radio link within a site or location. This is synonymous with sub10UnitLocalStatus sub10UnitLclLinkName |
| INT sub10UnitMgmtResetAction | 1.3.6.1.4.1.39003.3.2.20.5 | INTEGER | read-write | This is used to reset unit configuration and stats. resetFactoryDefaults(2) - Resets all configuration to Factory Defaults, requires a reboot. resetStatistics(3) - Resets according to setting of sub10UnitMgmtResetStatsGroup For reset of all stats sub10UnitMgmtResetStatsGroup = 'statsGroupAll'. resetAlarmConfig(4) - Resets according to setting of sub10UnitMgmtResetAlarmsType For reset of all alarms sub10UnitMgmtResetAlarmsType = 'resetAlarmTypeAll'. |
| INT sub10UnitMgmtResetAlarmsType | 1.3.6.1.4.1.39003.3.2.20.7 | INTEGER | read-write | This is used to reset specific alarm configuration when set prior to submitting sub10UnitMgmtResetAction = resetAlarmConfig(5). For reset of all alarms sub10UnitMgmtResetAlarmsType = resetAlarmTypeAll(1). |
| SUB sub10UnitMgmtResetStatsGroup | 1.3.6.1.4.1.39003.3.2.20.6 | Sub10StatsGroup | read-write | This is used to reset specific statistics when set prior to submitting sub10UnitMgmtResetAction = resetStatistics(4). For reset of all stats sub10UnitMgmtResetStatsGroup = 'statsGroupAll'. |
| U32 sub10UnitMgmtRollbackTimeout | 1.3.6.1.4.1.39003.3.2.20.3 | Unsigned32 | read-write | The timeout in seconds after which uncommitted Sets will be rolled back to their previous values. A rollback only affects those objects which are subject to transactions. |
| STR sub10UnitMgmtSiteName | 1.3.6.1.4.1.39003.3.2.1.4 | DisplayString | read-write | The administratively assigned physical location of the unit. This is synonymous with MIB-II sysLocation and sub10UnitLocalStatus sub10UnitLclSiteName. |
| sub10UnitMgmtSmtp | 1.3.6.1.4.1.39003.3.2.8 | |||
| sub10UnitMgmtSnmp | 1.3.6.1.4.1.39003.3.2.7 | |||
| sub10UnitMgmtSnmpAccessEntry | 1.3.6.1.4.1.39003.3.2.7.16.1 | not-accessible | An entry (row) in the sub10UnitMgmtSnmpAccessTable. If the rowStatus is set to notInService(2) then the entry is not valid and no columnar objects are returned. | |
| sub10UnitMgmtSnmpAccessEntryGrp | 1.3.6.1.4.1.39003.20.2.16 | This group defines objects that are members of the sub10UnitMgmtSnmpAccessEntryGrp group | ||
| U32 sub10UnitMgmtSnmpAccessIndex | 1.3.6.1.4.1.39003.3.2.7.16.1.1 | Unsigned32 | not-accessible | The sub10UnitMgmtSnmpAccessTable index. If the rowStatus is not set to enabled(1) then the entry is not valid and no columnar objects are returned except for the rowStatus object itself. |
| OCT sub10UnitMgmtSnmpAccessIpAddr | 1.3.6.1.4.1.39003.3.2.7.16.1.4 | OCTET STRING | read-write | The administratively assigned SNMP access IP address. Only SNMP requests from this address will be serviced by the SNMP agent. |
| OCT sub10UnitMgmtSnmpAccessName | 1.3.6.1.4.1.39003.3.2.7.16.1.3 | OCTET STRING | read-write | The administratively assigned SNMPv3 access name. This is used as an alias for the access address for purposes of identification. The name is not used in the SNMP protocol. |
| ROW sub10UnitMgmtSnmpAccessRowStatus | 1.3.6.1.4.1.39003.3.2.7.16.1.2 | RowStatus | read-create | The row status of this row. All table rows are fixed in size and as such do not require conceptual row creation. Instead the RowStatus is set to active(1) or notInService(2) which indicates that the row is operationally in use or not. The default value is notInService(2) meaning the entry is not used by default. To make the entry valid this object must be set to enabled(1), createAndGo(4) or createAndWait(5). To delete the row set this to destroy(6). |
| sub10UnitMgmtSnmpAccessTable | 1.3.6.1.4.1.39003.3.2.7.16 | not-accessible | The table of SNMPv3 Access configuration. | |
| SUB sub10UnitMgmtSnmpAdminAuthProto | 1.3.6.1.4.1.39003.3.2.7.11 | Sub10Snmpv3AuthProtocol | read-write | The authentication protocol currently assigned to users of group type administration. |
| SUB sub10UnitMgmtSnmpAdminPrivProto | 1.3.6.1.4.1.39003.3.2.7.12 | Sub10Snmpv3PrivProtocol | read-write | The privacy protocol currently assigned to users of group type administration. |
| SUB sub10UnitMgmtSnmpAgent | 1.3.6.1.4.1.39003.3.2.7.1 | Sub10State | read-write | If set to 'enabled' the agent will respond to valid v1/2c SNMP requests for GET/SET/GET-NEXT of supported MIB objects. If this object and the object sub10UnitMgmtSnmpv3 are both set to disabled then the unit will no longer respond to SNMP requests. If this object is set to enabled and sub10UnitMgmtSnmpv3 is set to enabled then the agent will respond to both both v1/2c and v3 SNMP requests. !! IMPORTANT !! If this object and sub10UnitMgmtSnmpv3 is set to disabled then the Agent will no longer respond therefore it will not be possible to re-enable the agent using SNMP. The agent can be re-enabled using the web GUI only. If this object is disabled then traps will not be forwarded by the unit. |
| OCT sub10UnitMgmtSnmpEngineId | 1.3.6.1.4.1.39003.3.2.7.8 | OCTET STRING | read-only | The administratively assigned SNMP v3 engine id. The construction of the engine id is dependant on the setting of sub10UnitMgmtSnmpEngineIdFormat and must be unique to the unit. |
| INT sub10UnitMgmtSnmpEngineIdFormat | 1.3.6.1.4.1.39003.3.2.7.6 | INTEGER | read-write | The format of this SNMP v3 agent's engine id. The engine id is administratively defined and is between 5 and 32 characters long and can be based on a number of formats defined here. |
| OCT sub10UnitMgmtSnmpEngineIdText | 1.3.6.1.4.1.39003.3.2.7.7 | OCTET STRING | read-write | When sub10UnitMgmtSnmpEngineIdFormat='textString(4)' this object contains the administratively defined string used to build the SNMP v3 engine id in sub10UnitMgmtSnmpEngineId. |
| sub10UnitMgmtSnmpGrp | 1.3.6.1.4.1.39003.20.2.13 | This group defines objects that are members of the sub10UnitMgmtSnmpGrp group | ||
| SUB sub10UnitMgmtSnmpMaintAuthProto | 1.3.6.1.4.1.39003.3.2.7.13 | Sub10Snmpv3AuthProtocol | read-write | The authentication protocol currently assigned to users of group type maintenance. |
| SUB sub10UnitMgmtSnmpMaintPrivProto | 1.3.6.1.4.1.39003.3.2.7.14 | Sub10Snmpv3PrivProtocol | read-write | The privacy protocol currently assigned to users of group type maintenance. |
| SUB sub10UnitMgmtSnmpOperAuthProto | 1.3.6.1.4.1.39003.3.2.7.9 | Sub10Snmpv3AuthProtocol | read-write | The authentication protocol currently assigned to users of group type operation. |
| SUB sub10UnitMgmtSnmpOperPrivProto | 1.3.6.1.4.1.39003.3.2.7.10 | Sub10Snmpv3PrivProtocol | read-write | The privacy protocol currently assigned to users of group type operation. |
| sub10UnitMgmtSnmpTargetEntry | 1.3.6.1.4.1.39003.3.2.7.17.1 | not-accessible | An entry (row) in the sub10UnitMgmtSnmpTargetTable. If the rowStatus is set to notInService(2) then the entry is not valid and no columnar objects are returned. | |
| sub10UnitMgmtSnmpTargetEntryGrp | 1.3.6.1.4.1.39003.20.2.17 | This group defines objects that are members of the sub10UnitMgmtSnmpTargetEntryGrp group | ||
| U32 sub10UnitMgmtSnmpTargetIndex | 1.3.6.1.4.1.39003.3.2.7.17.1.1 | Unsigned32 | not-accessible | The sub10UnitMgmtSnmpTargetTable index. If the rowStatus is not set to enabled(1) then the entry is not valid and no columnar objects are returned except for the rowStatus object itself. |
| OCT sub10UnitMgmtSnmpTargetIpAddr | 1.3.6.1.4.1.39003.3.2.7.17.1.4 | OCTET STRING | read-write | The administratively assigned SNMP target IP address. When enabled SNMPv3 Notifications are sent to this address. |
| OCT sub10UnitMgmtSnmpTargetName | 1.3.6.1.4.1.39003.3.2.7.17.1.3 | OCTET STRING | read-write | The administratively assigned SNMPv3 target name. |
| ROW sub10UnitMgmtSnmpTargetRowStatus | 1.3.6.1.4.1.39003.3.2.7.17.1.2 | RowStatus | read-create | The row status of this row. All table rows are fixed in size and as such do not require conceptual row creation. Instead the RowStatus is set to active(1) or notInService(2) which indicates that the row is operationally in use or not. The default value is notInService(2) meaning the entry is not used by default. To make the entry valid this object must be set to enabled(1), createAndGo(4) or createAndWait(5). To delete the row set this to destroy(6). |
| sub10UnitMgmtSnmpTargetTable | 1.3.6.1.4.1.39003.3.2.7.17 | not-accessible | The table of SNMPv3 Target configuration. This table defines the addresses of target SNMPv3 managers to send Notifications. | |
| OCT sub10UnitMgmtSnmpTargetUserName | 1.3.6.1.4.1.39003.3.2.7.17.1.5 | OCTET STRING | read-write | The administratively assigned SNMPv3 target user name. The security model configured for this user is used when sending notifications to the target address. |
| SUB sub10UnitMgmtSnmpTraps | 1.3.6.1.4.1.39003.3.2.7.2 | Sub10State | read-write | If set to 'enabled' the agent will forward traps to all configured trap destinations. If disabled traps are discarded. Traps are not sent if sub10UnitMgmtSnmpAgent is 'disabled(2)' regardless of the setting of this object. |
| OCT sub10UnitMgmtSnmpTrpDstCommunity | 1.3.6.1.4.1.39003.3.2.7.5.1.4 | OCTET STRING | read-write | The trap community name sent with each trap to this trap destination. The trap community allows for some security in the target management terminal |
| sub10UnitMgmtSnmpTrpDstEntry | 1.3.6.1.4.1.39003.3.2.7.5.1 | not-accessible | An entry (row) in the sub10UnitMgmtSnmpTrpDstTable. If the rowStatus is set to notInService(2) then the entry is not valid and no columnar objects are returned. | |
| sub10UnitMgmtSnmpTrpDstEntryGrp | 1.3.6.1.4.1.39003.20.2.14 | This group defines objects that are members of the sub10UnitMgmtSnmpTrpDstEntryGrp group | ||
| U32 sub10UnitMgmtSnmpTrpDstIndex | 1.3.6.1.4.1.39003.3.2.7.5.1.1 | Unsigned32 | not-accessible | The sub10UnitMgmtSnmpTrpDstTable index. If the rowStatus is not set to enabled(1) then the entry is not valid and no columnar objects are returned except for the rowStatus object itself. |
| OCT sub10UnitMgmtSnmpTrpDstIpAddr | 1.3.6.1.4.1.39003.3.2.7.5.1.3 | OCTET STRING | read-write | The administratively assigned SNMP Trap Destination IP. |
| ROW sub10UnitMgmtSnmpTrpDstRowStatus | 1.3.6.1.4.1.39003.3.2.7.5.1.2 | RowStatus | read-create | The row status of this row. All table rows are fixed in size and as such do not require conceptual row creation. Instead the RowStatus is set to active(1) or notInService(2) which indicates that the row is operationally in use or not. The default value is notInService(2) meaning the entry is not used by default. To make the entry valid this object must be set to enabled(1), createAndGo(4) or createAndWait(5). To delete the row set this to destroy(6). |
| sub10UnitMgmtSnmpTrpDstTable | 1.3.6.1.4.1.39003.3.2.7.5 | not-accessible | The table listing the each trap destination the local unit. Each trap destination has an IpAddress and a trap community string | |
| OCT sub10UnitMgmtSnmpUserAuthPwd | 1.3.6.1.4.1.39003.3.2.7.15.1.5 | OCTET STRING | read-write | The unique SNMPv3 authentication protocol password provided by the system administrator. This object can be set but is not visible when read. |
| OCT sub10UnitMgmtSnmpUserAuthPwdChk | 1.3.6.1.4.1.39003.3.2.7.15.1.6 | OCTET STRING | read-write | The unique SNMPv3 authentication protocol password provided by the system administrator used to verify the setting of sub10UnitMgmtSnmpUserAuthPassword. This object can be set but is not visible when read. |
| sub10UnitMgmtSnmpUserEntry | 1.3.6.1.4.1.39003.3.2.7.15.1 | not-accessible | An entry (row) in the sub10UnitMgmtSnmpUserTable. If the rowStatus is set to notInService(2) then the entry is not valid and no columnar objects are returned. | |
| sub10UnitMgmtSnmpUserEntryGrp | 1.3.6.1.4.1.39003.20.2.15 | This group defines objects that are members of the sub10UnitMgmtSnmpUserEntryGrp group | ||
| SUB sub10UnitMgmtSnmpUserGroup | 1.3.6.1.4.1.39003.3.2.7.15.1.4 | Sub10UserGroup | read-write | The user group type. Authentication and Privacy policies are assigned to a user group and not individual users. |
| U32 sub10UnitMgmtSnmpUserIndex | 1.3.6.1.4.1.39003.3.2.7.15.1.1 | Unsigned32 | not-accessible | The sub10UnitMgmtSnmpUserTable index. If the rowStatus is not set to enabled(1) then the entry is not valid and no columnar objects are returned except for the rowStatus object itself. |
| OCT sub10UnitMgmtSnmpUserName | 1.3.6.1.4.1.39003.3.2.7.15.1.3 | OCTET STRING | read-write | The administratively assigned SNMPv3 User name. |
| OCT sub10UnitMgmtSnmpUserPrivPwd | 1.3.6.1.4.1.39003.3.2.7.15.1.7 | OCTET STRING | read-write | The unique SNMPv3 privacy protocol password provided by the system administrator. This object can be set but is not visible when read. |
| OCT sub10UnitMgmtSnmpUserPrivPwdChk | 1.3.6.1.4.1.39003.3.2.7.15.1.8 | OCTET STRING | read-write | The unique SNMPv3 privacy protocol password provided by the system administrator used to verify the setting of sub10UnitMgmtSnmpUserPrivPassword. This object can be set but is not visible when read. |
| ROW sub10UnitMgmtSnmpUserRowStatus | 1.3.6.1.4.1.39003.3.2.7.15.1.2 | RowStatus | read-create | The row status of this row. All table rows are fixed in size and as such do not require conceptual row creation. Instead the RowStatus is set to active(1) or notInService(2) which indicates that the row is operationally in use or not. The default value is notInService(2) meaning the entry is not used by default. To make the entry valid this object must be set to enabled(1), createAndGo(4) or createAndWait(5). To delete the row set this to destroy(6). |
| sub10UnitMgmtSnmpUserTable | 1.3.6.1.4.1.39003.3.2.7.15 | not-accessible | The table of SNMPv3 User configuration. | |
| SUB sub10UnitMgmtSnmpv3 | 1.3.6.1.4.1.39003.3.2.7.4 | Sub10State | read-write | If set to 'enabled' the agent will support SNMPv3 PDUs and the SNMPv3 MIB configuration. This can be set to enabled or disabled independently of the object sub10UnitMgmtSnmpAgent which enables or disables the v1/2c agent. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2). |
| SUB sub10UnitMgmtSnmpv320Mib | 1.3.6.1.4.1.39003.3.2.7.3 | Sub10State | read-write | If set to 'enabled' the agent will support the Sub10 Systems v320 legacy MIB (LIBERATOR-MIB) objects and traps. |
| sub10UnitMgmtSyncE | 1.3.6.1.4.1.39003.3.2.13 | |||
| sub10UnitMgmtSyncEGrp | 1.3.6.1.4.1.39003.20.2.23 | This group defines objects that are members of the sub10UnitMgmtSyncEGrp group | ||
| INT sub10UnitMgmtSyncEMode | 1.3.6.1.4.1.39003.3.2.13.1 | INTEGER | read-write | The SyncE Mode. Setting this to syncEProvider(1) configures the unit as a Slave clock. In this case the unit at the other end of the link should be set to syncEConsumer(2). IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2). |
| sub10UnitMgmtSystem | 1.3.6.1.4.1.39003.3.2.1 | |||
| sub10UnitMgmtSystemGrp | 1.3.6.1.4.1.39003.20.2.5 | This group defines objects that are members of the sub10UnitMgmtSystemGrp group | ||
| OCT sub10UnitMgmtTerminalName | 1.3.6.1.4.1.39003.3.2.1.1 | OCTET STRING | read-write | The administratively assigned name for the unit. This is synonymous with MIB-II sysName and sub10UnitLocalStatus sub10UnitLclTerminalName. |
| sub10UnitMgmtTime | 1.3.6.1.4.1.39003.3.2.5 | |||
| sub10UnitMgmtTimeGrp | 1.3.6.1.4.1.39003.20.2.10 | This group defines objects that are members of the sub10UnitMgmtTimeGrp group | ||
| SUB sub10UnitMgmtTimeLocal | 1.3.6.1.4.1.39003.3.2.5.1 | Sub10DateTime | read-write | The administratively assigned system time defined as a display string in the format:- YYYY-MM-DD HH:MM:SS e.g. 2014-05-26 13:30:15 |
| SUB sub10UnitMgmtTimeNTPEnabled | 1.3.6.1.4.1.39003.3.2.5.2 | Sub10State | read-write | The administratively assigned state to enable or disable NTP. system cloack assignment automatically using the Network Time Protocol (NTP). |
| U32 sub10UnitMgmtTimeNTPPort | 1.3.6.1.4.1.39003.3.2.5.5 | Unsigned32 | read-write | The administratively assigned NTP Port number name to be used when contacting the NTP server. |
| OCT sub10UnitMgmtTimeNTPServer1 | 1.3.6.1.4.1.39003.3.2.5.3 | OCTET STRING | read-write | The administratively assigned primary NTP Server name. |
| OCT sub10UnitMgmtTimeNTPServer2 | 1.3.6.1.4.1.39003.3.2.5.4 | OCTET STRING | read-write | The administratively assigned secondary NTP Server name to be used when the primary server is not responding. |
| SUB sub10UnitMgmtTimeNTPSyncStatus | 1.3.6.1.4.1.39003.3.2.5.6 | Sub10NTPSyncStatus | read-only | The indication that the systems clock is synchronised with the NTP server. |
| INT sub10UnitMgmtTransaction | 1.3.6.1.4.1.39003.3.2.20.1 | INTEGER | read-write | This is used to commit or rollback the setting of object configuration. It only applies where the objects are subject to transactional requirements. For example the setting of the Unit's IP Address requires that a transaction be committed. If the transaction is not committed after a rollback timeout then the unit will automatically action a rollback to the previous value. The rollback timeout is configurable 'sub10UnitMgmtRollbackTimeout' |
| SUB sub10UnitMgmtTransactionMode | 1.3.6.1.4.1.39003.3.2.20.4 | Sub10State | read-write | Enables and Disables transactions. If sub10UnitMgmTransactionMode is stateDisabled(0) then no objects are subject to commit and rollback. |
| INT sub10UnitMgmtTransactionStatus | 1.3.6.1.4.1.39003.3.2.20.2 | INTEGER | read-write | This indicates either a transaction is currently in progress or if the last transaction was committed successfully or was rolled back. |
| sub10UnitMgmtUserEntry | 1.3.6.1.4.1.39003.3.2.4.2.1 | not-accessible | An entry (row) in the sub10UnitMgmtUserTable. If the rowStatus is set to notInService(2) then the entry is not valid and no columnar objects are returned. Usage is as follows: active(1) - Entry is created and in use. Any attempt to set this value will first check for consistent objects. If objects are found to be inconsistent then the entry will not be created and an error will be returned. notInService(2) - Entry is not created and not in use. Any attempt to set this value will result in the the entry remaining created but not accessible and not used. notReady(3) - Entry is created but has inconsistent objects, these must be set to correct values before the object can be set to active(1). createAndGo(4) - Set this to create a new entry and attempt to make the entry active(1). If the entry has inconsistent objects then this will set the entry to notReady(3) and an error will be returned. createAndWait(5)- Set this to create a new entry. This will set rowStatus = notReady(3). Related objects can then be set to consistent values before row_status can be set to active(1). destroy(6) - Set this to delete an entry. | |
| sub10UnitMgmtUserEntryGrp | 1.3.6.1.4.1.39003.20.2.9 | This group defines objects that are members of the sub10UnitMgmtUserEntryGrp group | ||
| SUB sub10UnitMgmtUserGroup | 1.3.6.1.4.1.39003.3.2.4.2.1.4 | Sub10UserGroup | read-write | The user group provided by the system administrator. This restricts a user to certain key functions on the web GUI. |
| U32 sub10UnitMgmtUserIndex | 1.3.6.1.4.1.39003.3.2.4.2.1.1 | Unsigned32 | not-accessible | The sub10UnitMgmtUserTable index. |
| OCT sub10UnitMgmtUserName | 1.3.6.1.4.1.39003.3.2.4.2.1.3 | OCTET STRING | read-write | The unique user name provided by the system administrator. |
| OCT sub10UnitMgmtUserPassword | 1.3.6.1.4.1.39003.3.2.4.2.1.5 | OCTET STRING | read-write | The unique user password provided by the system administrator. This object can be set but is not visible when read. |
| OCT sub10UnitMgmtUserPasswordVerify | 1.3.6.1.4.1.39003.3.2.4.2.1.6 | OCTET STRING | read-write | The unique user password provided by the system administrator use to verify the setting of sub10UnitMgmtUserPassword. This object can be set but is not visible when read. |
| ROW sub10UnitMgmtUserRowStatus | 1.3.6.1.4.1.39003.3.2.4.2.1.2 | RowStatus | read-create | The row status of this row. All table rows are fixed in size and as such do not require conceptual row creation. Instead the RowStatus is set to active(1) or notInService(2) which indicates that the row is operationally in use or not. The default value is notInService(2) meaning the entry is not used by default. To make the entry valid this object must be set to enabled(1), createAndGo(4) or createAndWait(5). To delete the row set this to destroy(6). |
| sub10UnitMgmtUsers | 1.3.6.1.4.1.39003.3.2.4 | |||
| sub10UnitMgmtUsersGrp | 1.3.6.1.4.1.39003.20.2.8 | This group defines objects that are members of the sub10UnitMgmtUsersGrp group | ||
| U32 sub10UnitMgmtUsersNumber | 1.3.6.1.4.1.39003.3.2.4.1 | Unsigned32 | read-only | The number of valid sub10UnitMgmtUsersTable table entries present on this system. |
| sub10UnitMgmtUserTable | 1.3.6.1.4.1.39003.3.2.4.2 | not-accessible | The table listing the users configured on the unit. The number of user entries is sub10UnitMgmtUsersNumber. This table is indexed by user name (sub10UnitMgmtUserName). Multiple entries with the same sub10UnitMgmtUserName are not possible. NB. As part of SNMPv3 support this table will be superceded by 'usmUserTable'. | |
| sub10UnitMgmtVlan | 1.3.6.1.4.1.39003.3.2.3 | |||
| SUB sub10UnitMgmtVlanDEI | 1.3.6.1.4.1.39003.3.2.3.5 | Sub10State | read-write | Set the Drop Eligible Indicator inserted into the ethernet frame for all management traffic. Only valid when the object sub10UnitMgmtVlanId is set to non zero. The DEI bit is set into the tag control information (TCI) field of each management frame. The DEI is a 1 bit field immediately following the PCP bits (3 bit field) IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2). |
| U32 sub10UnitMgmtVlanDSCP | 1.3.6.1.4.1.39003.3.2.3.4 | Unsigned32 | read-write | The Differentiated Services Code Point priority inserted into the IP header of all management traffic. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2). |
| sub10UnitMgmtVlanGrp | 1.3.6.1.4.1.39003.20.2.7 | This group defines objects that are members of the sub10UnitMgmtVlanGrp group | ||
| SUB sub10UnitMgmtVlanId | 1.3.6.1.4.1.39003.3.2.3.2 | Sub10VlanId | read-write | The VLAN Id used to carry management traffic. Only valid when the object is set to a non-zero value. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2). |
| U32 sub10UnitMgmtVlanPriority | 1.3.6.1.4.1.39003.3.2.3.3 | Unsigned32 | read-write | The VLAN priority inserted into the ethernet frame for all management traffic. Only valid when the object sub10UnitMgmtVlanId is set to non zero. IMPORTANT: This object is controlled by transaction management. Any changes to this object must be transactionally acknowledged following a successful set thus protecting against loss of communication with the unit. To acknowledge the transaction set the object sub10UnitMgmtTransaction to transactionCommit(2). |
| SUB sub10UnitMgmtVlanState | 1.3.6.1.4.1.39003.3.2.3.1 | Sub10State | read-write | Enable VLAN for Management traffic. . |
| sub10UnitRemoteStatus | 1.3.6.1.4.1.39003.3.1.2 | |||
| sub10UnitRemoteStatusGrp | 1.3.6.1.4.1.39003.20.2.4 | This group defines objects that are members of the sub10UnitRemoteStatusGrp group | ||
| OCT sub10UnitRmtFirmwareVersion | 1.3.6.1.4.1.39003.3.1.2.8 | OCTET STRING | read-only | The firmware version currently running on the remote unit. This is by definition the firmware loaded into the bank currently used for boot. See sub10UnitMgmtFirmware. |
| OCT sub10UnitRmtHWSerialNumber | 1.3.6.1.4.1.39003.3.1.2.7 | OCTET STRING | read-only | The hardware serial number of the Remote Unit. This also identifies whether the unit is a V-band or E-band product. |
| OCT sub10UnitRmtIpAddress | 1.3.6.1.4.1.39003.3.1.2.9 | OCTET STRING | read-only | The IP address of the remote ethernet interface. |
| OCT sub10UnitRmtLinkId | 1.3.6.1.4.1.39003.3.1.2.6 | OCTET STRING | read-only | The administratively assigned identifier on the remote unit for the radio link between the local and remote units. The LinkId must be the same value on both local and remote units. |
| OCT sub10UnitRmtLinkName | 1.3.6.1.4.1.39003.3.1.2.5 | OCTET STRING | read-only | The administratively assigned name on the remote unit for the radio link between the local and remote units. This generally identifies geographically the two ends or a radio link within a site or location. |
| I32 sub10UnitRmtMWUTemperature | 1.3.6.1.4.1.39003.3.1.2.10 | Integer32 | read-only | The modem temperature on the local unit in degrees celsius. |
| OCT sub10UnitRmtTerminalName | 1.3.6.1.4.1.39003.3.1.2.3 | OCTET STRING | read-only | The administratively assigned name for the remote unit. This is synonymous with MIB-II sysName. |
| SUB sub10UnitRmtTerminalType | 1.3.6.1.4.1.39003.3.1.2.4 | Sub10TerminalType | read-only | Uniquely identifies the remote terminal type A or B. |
| SUB sub10UnitRmtTime | 1.3.6.1.4.1.39003.3.1.2.2 | Sub10DateTime | read-only | The remote unit local system time as a display string in the format:- YYYY-MM-DD,HH:MM:SS e.g. 2014-5-26,13:30:15 |
| SUB sub10UnitRmtUnitType | 1.3.6.1.4.1.39003.3.1.2.1 | Sub10UnitType | read-only | Uniquely identifies the remote unit product type |
| sub10UnitStatus | 1.3.6.1.4.1.39003.3.1 |
RFC description
Manages Sub10 Systems wireless Ethernet bridges including radio stats, alarms, and multi-ethernet port configuration.
Start monitoring Sub10 Systems point-to-point microwave radio link terminal (firmware/identity status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.