All MIBs › SYMBOL-DSSS-ENTERPRISE-PRIVATE-MIB
Category: Radio and Wireless
Description: Manages Symbol DSSS wireless enterprise private objects for spread-spectrum radio configuration.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is SYMBOL-DSSS-ENTERPRISE-PRIVATE-MIB?
SYMBOL-DSSS-ENTERPRISE-PRIVATE-MIB is a Symbol Technologies (802.11 DSSS wireless access point vendor, enterprise OID 388, later Motorola/Zebra) proprietary MIB reporting access-point hardware identification and network/service configuration. Its objects cover model/serial number, hardware/AP-firmware/RF-firmware revision, MAC address, manufacture date, HTML-file revision, vendor ID, unit name, IP address/subnet mask/gateway, default interface, Ethernet port state/timeout, Telnet/access-control/type-filter/WNMP enable flags, AP-state-exchange enable, mobile-IP enable, advertisement interval, web-server enable, and mobile-home MD5 key. As a hardware/configuration MIB it lets an administrator confirm firmware revisions and network configuration on a Symbol DSSS access point. It is deployed on Symbol Technologies (Motorola/Zebra) 802.11 DSSS access points. Engineers can download the SYMBOL-DSSS-ENTERPRISE-PRIVATE-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in SYMBOL-DSSS-ENTERPRISE-PRIVATE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Symbol Technologies (Motorola/Zebra) 802.11 DSSS access points
Monitoring Examples
An administrator checks apAPFirmwareRev and apRFFirmwareRev to confirm firmware consistency across a fleet of Symbol Technologies DSSS access points.
What Can Be Monitored
- access point firmware versions and network configuration
This MIB depends on
Related MIBs
Imported Objects
From RFC-1212
| OBJECT-TYPE |
From RFC-1215
| TRAP-TYPE |
From RFC1155-SMI
| Counter | |
| Gauge | |
| IpAddress | |
| TimeTicks | |
| enterprises |
From RFC1213-MIB
| DisplayString | |
| PhysAddress | |
| snmp |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| INT additionalGatewaysIndex | 1.3.6.1.4.1.388.1.5.1.2.19.1.1 | INTEGER | read-only | Specific Gateway information Table index. Range (1..8). |
| INT allowedIndex | 1.3.6.1.4.1.388.1.5.4.3.1.1 | INTEGER | read-only | Access Control Table index. Range (1..512). |
| PHY allowedMU | 1.3.6.1.4.1.388.1.5.4.3.1.2 | PhysAddress | read-write | MU MAC address which is allowed to associate with this AP. |
| INT ap128bWEPFlag | 1.3.6.1.4.1.388.1.5.4.7 | INTEGER | read-only | When enabled, This flag indicates that AP is enabled to supports strong(128 bit) Encryption. The state of this flag is internally set only by the AP. when a valid access code is entered for apWEPLicenseKey object and accepted the AP will set the state of this flag to enabled. Default is disabled. |
| INT ap128bWepkeyIndex | 1.3.6.1.4.1.388.1.5.1.8.1.1 | INTEGER | read-only | WEP Key Table index. Range (1..4). |
| ap128bWEPKeyTable | 1.3.6.1.4.1.388.1.5.1.8 | not-accessible | A table of default WEP Keys The maximum number of entries in the table is 4. | |
| WEP ap128bWepKeyValue | 1.3.6.1.4.1.388.1.5.1.8.1.2 | WEPKeytype128b | read-write | A Default WEP Key Value. This value should be 26 character long. IMPORTANT NOTE: The 128 bit WEP key Encryption is currently restricted by U.S. laws. Its use is restricted to AP's manufactured for U.S. only. In order to activate the 128 bit Encryption for all other countries, an access code has to be obtained and entered through one of the interfaces such as Serial, Telnet, SNMP or Web. Upon authentication of the key the AP will enable the 128 bit Encryption. See Access Point manual for details. |
| INT ap802dot11Protocol | 1.3.6.1.4.1.388.1.5.2.9.1.8 | INTEGER | read-only | Indicate that whether this known AP is 802.11 compliant. |
| INT apAccCtrlEnable | 1.3.6.1.4.1.388.1.5.1.2.9 | INTEGER | read-write | Enables/Disables the Access Control function. When it is enabled, a Mobile Unit can associate with the Access Point only if its MAC address is in the Access Control Table. Default is disabled(2). |
| apAccCtrlEntry | 1.3.6.1.4.1.388.1.5.4.3.1 | not-accessible | An entry in the table of MAC address Access Control. A row in this table is created by setting the value of allowedMU to the MAC address of the MU allowed to associate with this Access Point. A row in this table is deleted by setting the value of allowedMU to '000000000000'. | |
| apAccCtrlTable | 1.3.6.1.4.1.388.1.5.4.3 | not-accessible | A table of MAC addresses allowed to associate with the Access Point. The maximum number of entries in the table is 512. | |
| INT apAcceptBCESSID | 1.3.6.1.4.1.388.1.5.1.4.14 | INTEGER | read-write | Enables/Disables the function to accept Broadcast ESS ID. Enabling this feature is NOT recommended. See manual for details. Default is disabled(2). |
| apACLRangeEntry | 1.3.6.1.4.1.388.1.5.4.4.1 | not-accessible | An entry in the table of MAC address Access Control Range. A row in this table is created by first setting the value of lowMacAddr to the lowest MAC address and then the value of highMacAddr to the highest MAC address of a group of Mobile Units allowed to associate with this Access Point. This sequence of setting is very important, otherwise a wrong result will occur. A row in this table is deleted by setting the value of either lowMacAddr or highMacAddr to '000000000000'. | |
| INT apACLRangeIndex | 1.3.6.1.4.1.388.1.5.4.4.1.1 | INTEGER | read-only | Access Control Range Table index. Range (1..8). |
| apACLRangeTable | 1.3.6.1.4.1.388.1.5.4.4 | not-accessible | A table of Access Control Range, which consists of eight (8) pairs of low and high MAC addresses. Any Mobile Unit with the MAC address within the range is allowed to associate with the Access Point. The maximum number of entries in the table is 8. | |
| INT apACLTrapEnable | 1.3.6.1.4.1.388.1.5.1.3.9 | INTEGER | read-write | Enables/Disables Access Control violation trap. Default is disabled(2). This is an enterprise-specific trap and the trap code is 102. When not disabled the trap could be directed to TrapHost1, TrapHost2 or all TrapHosts. The apAllTrapsEnable flag should be enabled for this trap to be issued. |
| CTR apACLViolations | 1.3.6.1.4.1.388.1.5.4.1 | Counter | read-only | Indicates the number of Access Control violations occurred. |
| apAdditionalGatewaysEntry | 1.3.6.1.4.1.388.1.5.1.2.19.1 | not-accessible | An entry in the table of information for additional gateways for this access point. A row in this table cannot be created or deleted by SNMP operations on columns of the table. | |
| IP apAdditionalGatewaysIPAddr | 1.3.6.1.4.1.388.1.5.1.2.19.1.2 | IpAddress | read-write | The IP address of the Gateway used for this AP. |
| apAdditionalGatewaysTable | 1.3.6.1.4.1.388.1.5.1.2.19 | not-accessible | A table of information for additional Gateways. The current number of entries is 7. | |
| apAddrFilterEntry | 1.3.6.1.4.1.388.1.5.1.6.1 | not-accessible | An entry in the table of Address Filter. A row in this table is created by setting the value of disallowedMU to the MAC address of the MU not allowed to associate with the Access Point. A row in this table is deleted by setting the value of disallowedMU to '000000000000'. | |
| apAddrFilterTable | 1.3.6.1.4.1.388.1.5.1.6 | not-accessible | A table of MAC addresses not allowed to associate with the Access Point. The maximum number of entries in the table is 512. | |
| CTR apAdrViolations | 1.3.6.1.4.1.388.1.5.2.10.1 | Counter | read-only | Indicates the number of Mobile Unit MAC address violations counted. |
| INT apAgentAdInterval | 1.3.6.1.4.1.388.1.5.1.2.16 | INTEGER | read-write | Interval in second at which Mobility Agent Advertise- ments are sent by the Third Party Mobility Agent(s). AP will cache the Third Party Advertisement and pass it to MU at association time. If AP does not receive the Advertisement within the interval seconds, the cached Advertisement will be deleted. If the interval is 0 or apS24MobileIPEnable is enabled, caching of the Advertisement will not occur. Range (0..1200) 3*Seconds . Default is 0. |
| CTR apAgentAdSents | 1.3.6.1.4.1.388.1.5.2.14.1 | Counter | read-only | Counter for the number agent advertisement sent. |
| INT apAllTrapsEnable | 1.3.6.1.4.1.388.1.5.1.3.5 | INTEGER | read-write | Enables/Disables all SNMP traps. Default is disabled (2). |
| INT apAnswerWaitTime | 1.3.6.1.4.1.388.1.5.1.5.7 | INTEGER | read-write | Specifies the period (in seconds) the AP will wait for the remote unit to answer the call. Default is 60 seconds. |
| INT apAntennaSelect | 1.3.6.1.4.1.388.1.5.1.4.6 | INTEGER | read-write | Select either Primary antenna only (i.e. Disable antenna diversity) or both Primary and Secondary antennas (i.e. Enable antenna diversity-On). Default is diversity-On(2). |
| STR apAPFirmwareRev | 1.3.6.1.4.1.388.1.5.1.1.5 | DisplayString | read-only | The current revision of the Access Point firmware. |
| IP apAPIpAddr | 1.3.6.1.4.1.388.1.5.2.9.1.2 | IpAddress | read-only | IP Address of this Known AP. |
| PHY apAPMacAddr | 1.3.6.1.4.1.388.1.5.2.9.1.1 | PhysAddress | read-only | Mac Address of this Known AP. |
| INT apAPStateXchgEnable | 1.3.6.1.4.1.388.1.5.1.2.14 | INTEGER | read-write | Enables/Disables exchanging Access Point to Access Point state information by using WNMP protocol. Default is enabled(1). |
| INT apAuthenFailureTrapEnable | 1.3.6.1.4.1.388.1.5.1.3.7 | INTEGER | read-write | Enables/Disables authentication failure trap. Default is disabled(2). This is a generic-trap and the trap code is 4. When not disabled the trap could be directed to TrapHost1, TrapHost2 or all TrapHosts. The apAllTrapsEnable flag should be enabled for this trap to be issued. |
| INT apAway | 1.3.6.1.4.1.388.1.5.2.9.1.7 | INTEGER | read-only | Indicate that whether this known AP is still alive or not. If the current AP does not receive WNMP packet from this known AP within 36 seconds, this known AP is considered 'AWAY'. |
| INT apBCMCQMax | 1.3.6.1.4.1.388.1.5.1.4.8 | INTEGER | read-write | The maximum size of broadcast/multicast queue. Range (0..32). Default is 10. |
| INT apClrACL | 1.3.6.1.4.1.388.1.5.3.3 | INTEGER | read-write | Clear the Access Control Table (yes = 1, no = 2). |
| INT apClrACLRangeTable | 1.3.6.1.4.1.388.1.5.3.4 | INTEGER | read-write | Clear the Access Control Range Table (yes = 1, no = 2). |
| INT apClrAddrFilterTbl | 1.3.6.1.4.1.388.1.5.3.5 | INTEGER | read-write | Clear the Address Filtering Table (yes = 1, no = 2). |
| INT apClrAllStatistics | 1.3.6.1.4.1.388.1.5.3.1 | INTEGER | read-write | Clear all the interface statistics (yes = 1, no = 2). |
| INT apClrMUTable | 1.3.6.1.4.1.388.1.5.3.2 | INTEGER | read-write | Clear the MU Table (yes = 1, no = 2). |
| INT apColdBootTrapEnable | 1.3.6.1.4.1.388.1.5.1.3.6 | INTEGER | read-write | Enables/Disables Access Point Cold Boot trap. Default is disabled(1). This is a generic-trap and the trap code is 0. When not disabled the trap could be directed to TrapHost1, TrapHost2 or all TrapHosts. The apAllTrapsEnable flag should be enabled for this trap to be issued. |
| apConfigMgmt | 1.3.6.1.4.1.388.1.5.1 | |||
| INT apConnectMode | 1.3.6.1.4.1.388.1.5.1.5.4 | INTEGER | read-write | Specifies the Modem connection mode: - originate(1): AP sends dial-out information. - answer(2): AP waits for dial-in information. Default is answer(2). |
| STR apCountryName | 1.3.6.1.4.1.388.1.5.1.4.5 | DisplayString | read-only | The country for which the Access Point radio is configured. It is set at the factory and may not be altered. |
| TIK apCurrCallTime | 1.3.6.1.4.1.388.1.5.2.6.4 | TimeTicks | read-only | Indicates the length in seconds of current connection session. Note: the time is relative to the boot time of this AP. |
| CTR apCurrentMUs | 1.3.6.1.4.1.388.1.5.2.8.1 | Counter | read-only | Indicates the number of MUs currently associated with this AP. |
| INT apDefaultInterface | 1.3.6.1.4.1.388.1.5.1.2.5 | INTEGER | read-write | Specifies the default interface (Ethernet, PPP or WLAP) for the AP to forward an unknown packet. Default is ethernet(1). |
| INT apDHCPChangeEnable | 1.3.6.1.4.1.388.1.5.1.3.12 | INTEGER | read-write | When Enabled, if there are any DHCP network configuration change, a trap will be issued. Default is disabled(2). When not disabled the trap could be directed to TrapHost1, TrapHost2 or all TrapHosts. The apAllTrapsEnable flag should be enabled for this trap to be issued. |
| INT apDHCPEnable | 1.3.6.1.4.1.388.1.5.3.15 | INTEGER | read-write | Enables/Disables DHCP mode for the AP. Default is disabled(2). |
| CTR apDialoutFailures | 1.3.6.1.4.1.388.1.5.2.6.2 | Counter | read-only | Indicates the number of dialout failures by the AP. |
| INT apDialOutMode | 1.3.6.1.4.1.388.1.5.1.5.6 | INTEGER | read-write | Specifies the dialout mode: - auto(1): Modem dial out during startup time. - manual(2): Modem dial out by manned intervention Default is auto(1). |
| STR apDialOutNumber | 1.3.6.1.4.1.388.1.5.1.5.5 | DisplayString | read-write | Specifies the number to be dialed by the modem. |
| STR apDnLdFileName | 1.3.6.1.4.1.388.1.5.3.10 | DisplayString | read-write | The name of the file to be downloaded to the AP. (Including path name and total up to 49 characters.) Note: IF DHCP is responded to, that name will take precedence and overwrite this name. |
| NTF apDSAPACLViolationTrap | 1.3.6.1.4.1.388.1.5.0.102 | Mobile Unit MAC address not in the Access control Table. - apMyMacAddr is the MAC address of the Access Point sending this trap message. - muMacAddr is the MAC address of the Mobile Unit not in the Access Control Table. | ||
| NTF apDSAPDHCPConfigChgTrap | 1.3.6.1.4.1.388.1.5.0.130 | If there are any DHCP network configuration change, This trap will be issued. - apMyMacAddr is the MAC address of the Access Point sending this trap message. | ||
| NTF apDSAPDHCPLeaseUpTrap | 1.3.6.1.4.1.388.1.5.0.131 | If the Access point(Client) is unable to renew the DHCP lease before the lease is expired, this trap is generated. - apMyMacAddr is the MAC address of the Access Point sending this trap message. | ||
| NTF apDSAPMUAssocTrap | 1.3.6.1.4.1.388.1.5.0.111 | Indicates that there is one Mobile Unit associating with this Access Point. - apMyMacAddr is the MAC address of the Access Point sending this trap message. - muMacAddr is the MAC address of the Mobile Unit. Note : If two or more Mobile Units associate with the Access Point at the same time, muMacAddr belongs to the last Mobile Unit. - apCurrentMUs is the number of Mobile Units currently associating with this Access Point. | ||
| NTF apDSAPMUMaxAssocTrap | 1.3.6.1.4.1.388.1.5.0.116 | Indicates that the number of MUs associated with this Access Point is at the threshold set by apMaxMUTrigger. - apMyMacAddr is the MAC address of the Access Point sending this trap message. - apCurrentMUs is the number of Mobile Units currently associating with this Access Point. | ||
| NTF apDSAPMUUnAssocTrap | 1.3.6.1.4.1.388.1.5.0.112 | Indicates that there is one Mobile Unit no longer associating with this Access Point anymore. - apMyMacAddr is the MAC address of the Access Point sending this trap message. - muMacAddr is the MAC address of the Mobile Unit. Note : If two or more Mobile Units un-associate with the Access Point at the same time, muMacAddr belongs to the last Mobile Unit. - apCurrentMUs is the number of Mobile Units currently associating with this Access Point. | ||
| NTF apDSAPRFStartUpTrap | 1.3.6.1.4.1.388.1.5.0.101 | RF Driver is up. - apMyMacAddr is the MAC address of the Access Point sending this trap message. | ||
| INT apDSchannel | 1.3.6.1.4.1.388.1.5.2.9.1.10 | INTEGER | read-only | The current operating frequency channel of the DSSS PHY. Valid channel numbers are as defined in IEEE 802.11 specification section 15.4.6.2. |
| NTF apDSDsgnatedWLAPLostTrap | 1.3.6.1.4.1.388.1.5.0.124 | If the current wireless AP does not receive Config BPDU (Bridge Protocol Data Unit) packet from its Designated WLAP for MAX AGE time, it will consider that the Designated WLAP is lost. - apMyMacAddr is the MAC address of the Access Point sending this trap message. - apAPMacAddr is the MAC address of the Designated WLAP. - apNbrOfWLAPItfs is the number of current WLAP Interfaces established. | ||
| NTF apDSDsgntedWLAPUpTrap | 1.3.6.1.4.1.388.1.5.0.123 | Indicates that the Designated WLAP connection is setup and is ready to forward data. - apMyMacAddr is the MAC address of the Access Point sending this trap message. - apAPMacAddr is the MAC address of the Designated WLAP. - apNbrOfWLAPItfs is the number of current WLAP Interfaces established. | ||
| INT apDsgnatedCost | 1.3.6.1.4.1.388.1.5.2.11.8.1.6 | INTEGER | read-only | The cost of the path to the Root AP designated by the Root AP. |
| OCT apDsgnatedItf | 1.3.6.1.4.1.388.1.5.2.11.8.1.8 | OCTET STRING | read-only | The WLAP interface ID designated by the Root AP. |
| OCT apDsgnatedRoot | 1.3.6.1.4.1.388.1.5.2.11.8.1.5 | OCTET STRING | read-only | The unique Root AP ID designated by the Root AP. |
| OCT apDsgnatedWLAP | 1.3.6.1.4.1.388.1.5.2.11.8.1.7 | OCTET STRING | read-only | The unique WLAP ID designated by the Root AP. |
| apDSPerFreqStatEntry | 1.3.6.1.4.1.388.1.5.2.13.1 | not-accessible | An entry in the table of Radio per frequency statistics. A row in this table cannot be created or deleted by SNMP operations on columns of the table. | |
| apDSPerFreqStatTable | 1.3.6.1.4.1.388.1.5.2.13 | not-accessible | A table of Radio Per Frequency statistics, which is based on the historical frequency records used by this Access Point. The current number of entries is 78. | |
| NTF apDSRootWLAPLostTrap | 1.3.6.1.4.1.388.1.5.0.122 | If the current wireless AP does not receive Beacon packet from its Root AP within one second, it will consider the Root AP is lost. The wireless AP will eventually reset itself to re-establish the network topology. - apMyMacAddr is the MAC address of the Access Point sending this trap message. - apAPMacAddr is the MAC address of the Root AP. - apNbrOfWLAPItfs is the number of current WLAP Interfaces established. | ||
| NTF apDSRootWLAPUpTrap | 1.3.6.1.4.1.388.1.5.0.121 | Indicates that the Root AP connection is setup and is ready to forward data. - apMyMacAddr is the MAC address of the Access Point sending this trap message. - apAPMacAddr is the MAC address of the Root AP. - apNbrOfWLAPItfs is the number of current WLAP Interfaces established. | ||
| CTR apE1orMoreColls | 1.3.6.1.4.1.388.1.5.2.3.9 | Counter | read-only | Indicates the number of packets that suffer more than one collision. |
| CTR apEAnyCollisions | 1.3.6.1.4.1.388.1.5.2.3.8 | Counter | read-only | Indicates the number of packets that suffer at least one collision. |
| CTR apEBcMcPkts | 1.3.6.1.4.1.388.1.5.2.3.13 | Counter | read-only | Indicates the number of broadcast/multicast packets that have been transmitted. |
| CTR apEIndividualAddrs | 1.3.6.1.4.1.388.1.5.2.3.14 | Counter | read-only | Indicates the number of individual address (unicast) packets that have been received. |
| CTR apELateCollisions | 1.3.6.1.4.1.388.1.5.2.3.11 | Counter | read-only | Indicates the number of packets that suffer late collisions. |
| CTR apEMaxCollisions | 1.3.6.1.4.1.388.1.5.2.3.10 | Counter | read-only | Indicates the number of packets that suffer more than the maximum number of collisions. |
| INT apEncryptAdmin | 1.3.6.1.4.1.388.1.5.1.2.21 | INTEGER | read-only | Controls the administration of Encryption keys. This variable could only be modified thru the Serial Interface. Default is any(2). |
| INT apEnetPortState | 1.3.6.1.4.1.388.1.5.1.2.6 | INTEGER | read-write | Specifies the state of the Ethernet interface. Default is up(1). |
| CTR apEPktsDefers | 1.3.6.1.4.1.388.1.5.2.3.12 | Counter | read-only | Indicates the times AP had to defer transmit requests on Ethernet due to busy medium. |
| CTR apEPktsDiscBuffers | 1.3.6.1.4.1.388.1.5.2.3.5 | Counter | read-only | Indicates the number of packets discarded due to lack of available buffers in AP. |
| CTR apEPktsDiscCRCs | 1.3.6.1.4.1.388.1.5.2.3.6 | Counter | read-only | Indicates the number of packets discarded due to CRC errors. |
| CTR apEPktsDiscForceds | 1.3.6.1.4.1.388.1.5.2.3.4 | Counter | read-only | Indicates the number of packets discarded due to Type or Address filters applied. |
| CTR apEPktsDiscNoMatchs | 1.3.6.1.4.1.388.1.5.2.3.3 | Counter | read-only | Indicates the number of packets discarded due to unknown destination (i.e. no database entry). |
| CTR apEPktsForwardeds | 1.3.6.1.4.1.388.1.5.2.3.2 | Counter | read-only | Indicates the number of Ethernet packets forwarded from the Ethernet interface to other interfaces. |
| CTR apEPktsSeens | 1.3.6.1.4.1.388.1.5.2.3.1 | Counter | read-only | Indicates the number of packets that have been seen on the Ethernet interface. Most of these packets are for stations other than those associated with this AP. |
| CTR apEPktsSents | 1.3.6.1.4.1.388.1.5.2.3.7 | Counter | read-only | Indicates the number of packets sent by this Ethernet Port. |
| apEthernetStatistics | 1.3.6.1.4.1.388.1.5.2.3 | |||
| INT apEthernetTimeOut | 1.3.6.1.4.1.388.1.5.1.2.7 | INTEGER | read-write | If the value is: - 0: the Ethernet Time Out function is disabled. - 1: detect Ethernet timeout by hardware circuitry. - 30-255: Ethernet timeout is detected by software algorithm. When the Ethernet connection is broken and the WLAP mode is either enabled or disabled, the AP will clear the MU table and disable the RF interface until the Etherent connection is up. The following values are only valid when WLAP mode is enabled and it does not matter whetehr WLAP associates with the root AP or not. - 2: send WLAP Alive BPDU on Ethernet interface to let other WLAP on the same Ethernet segment to detect it's existence. - 3: keep track of WLAP Alive BPDU on Ethernet inter- face. If the BPDU is missing for 'WLAP Hello Time' seconds, the Ethernet Activity LEDs will flash and the RF interface is disabled until the WLAP Alive BPDU is received again, then the AP will reset itself. The default value is 0. |
| apFaultMgmt | 1.3.6.1.4.1.388.1.5.3 | |||
| INT apFileUpdateStatus | 1.3.6.1.4.1.388.1.5.3.20 | INTEGER | read-only | Reports the Firmware/HTML file download and update status. |
| apFilterStatistics | 1.3.6.1.4.1.388.1.5.2.10 | |||
| INT apFlashLEDs | 1.3.6.1.4.1.388.1.5.3.21 | INTEGER | read-write | When this command is issued, it forces all status LEDs on the AP to start flashing. This command is primarily used for physically locating the AP where multiple APs are deployed. (yes = 1, no = 2) Default is no. |
| STR apFwVer | 1.3.6.1.4.1.388.1.5.2.9.1.9 | DisplayString | read-only | Indicates The firmware revision for this known Access Point. |
| IP apGatewayIPAddr | 1.3.6.1.4.1.388.1.5.1.2.4 | IpAddress | read-write | The IP address for the default gateway. |
| STR apHardwareRev | 1.3.6.1.4.1.388.1.5.1.1.3 | DisplayString | read-only | The current revision of the Access Point hardware. |
| STR apHelpURL | 1.3.6.1.4.1.388.1.5.3.19 | DisplayString | read-write | The name of the HTML Help file . (Including path name and total up to 39 characters.) |
| INT apHoppingSeq | 1.3.6.1.4.1.388.1.5.2.9.1.4 | INTEGER | read-only | Hopping Sequence of this Known AP. |
| INT apHoppingSet | 1.3.6.1.4.1.388.1.5.2.9.1.3 | INTEGER | read-only | Hopping Set of this Known AP. |
| STR apHTMLFileName | 1.3.6.1.4.1.388.1.5.3.13 | DisplayString | read-write | The name of the HTML file to be downloaded to the AP. (Including path name and total up to 49 characters.) Note: IF DHCP is responded to, that name will take precedence and overwrite this name. |
| STR apHTMLFileRev | 1.3.6.1.4.1.388.1.5.1.1.8 | DisplayString | read-only | The current revision of the Access Point HTML file. |
| INT apInactivityTimeout | 1.3.6.1.4.1.388.1.5.1.5.9 | INTEGER | read-write | Specifies the User Interface inactivity timeout in minutes. 0 means no timeout. Default is 5 minutes. |
| STR apInterfaceName | 1.3.6.1.4.1.388.1.5.2.2.1.2 | DisplayString | read-only | Access Point Interface Name (Ethernet, PPP, RF, AP). |
| apItfStatEntry | 1.3.6.1.4.1.388.1.5.2.2.1 | not-accessible | An entry in the table of Access Point Interface Statistics. A row in this table cannot be created or deleted by SNMP operations on columns of the table. | |
| INT apItfStatIndex | 1.3.6.1.4.1.388.1.5.2.2.1.1 | INTEGER | read-only | Access Point Interface Statistics Table index. Range (1..4). |
| apItfStatTable | 1.3.6.1.4.1.388.1.5.2.2 | not-accessible | A table of Access Point Interfaces Statistics, which provides packets forwarding statistics for each inter- face (Ethernet, PPP, RF, AP stack). Interface statistics also provide performance informa- tion for each interface in Packets-per-second (PPS) and Bytes- per-second (BPS). The AP interface indicates packets sent to the AP stack (e.g. configuration requests, SNMP, Telnet etc.). The current number of entries is 4. | |
| INT apKBIOS | 1.3.6.1.4.1.388.1.5.2.9.1.6 | INTEGER | read-only | Kilobytes sent and received per second by this known AP on the radio interface. |
| apKnownAPsEntry | 1.3.6.1.4.1.388.1.5.2.9.1 | not-accessible | An entry in the table of information on the Known Access Points. A row in this table cannot be created or deleted by SNMP operations on columns of the table. | |
| apKnownAPsTable | 1.3.6.1.4.1.388.1.5.2.9 | not-accessible | A table of information on other Access Points known by this Access Point. The current number of entries is 32. | |
| TIK apLastCallTime | 1.3.6.1.4.1.388.1.5.2.6.5 | TimeTicks | read-only | Indicates the length in seconds of last connection session. Note: the time is relative to the boot time of this AP. |
| INT apLdACLFrMUList | 1.3.6.1.4.1.388.1.5.3.6 | INTEGER | read-write | Load the Access Control Table from MU Table (yes = 1, no = 2). |
| apManufactureInfo | 1.3.6.1.4.1.388.1.5.1.1 | |||
| CTR apMaxMUs | 1.3.6.1.4.1.388.1.5.2.8.2 | Counter | read-only | Indicates the highest number of MUs ever associated with this AP. |
| INT apMaxMUTrigger | 1.3.6.1.4.1.388.1.5.1.4.24 | INTEGER | read-write | Indicates the trigger point for sending apMUMaxAssocTrap trap. Range (1..255). The default value is 255. |
| INT apMaxRetries | 1.3.6.1.4.1.388.1.5.1.4.10 | INTEGER | read-write | The maximum number of allowed retries before aborting a single transmission. Range (0..32). Default is 15. |
| INT apMaxRetriesVoice | 1.3.6.1.4.1.388.1.5.1.4.25 | INTEGER | read-write | The maximum number of allowed retries before aborting a single transmission. Range (0..32). Default is 5. |
| OCT apMcastMaskVoice | 1.3.6.1.4.1.388.1.5.1.4.26 | OCTET STRING | read-write | This is used for Spectrum 24 telephone for intercomm function. The multicast mask is the top 32 bits of the MAC address and allows for a series of MAC addresses to receive multicast messages. These messages are transmitted by the AP immediately and not queued for processing at DTIM intervals.. |
| STR apMfgDate | 1.3.6.1.4.1.388.1.5.1.1.7 | DisplayString | read-only | The Date this Access Point was manufactured. |
| STR apMobileHomeMD5Key | 1.3.6.1.4.1.388.1.5.1.2.18 | DisplayString | read-write | The MD5 key is a secret key shared between home agent and the mobile unit. This is used to generate a MD5 checksum, which is used for packet authentication. Length of this variable should not exceed 13 characters. |
| apMobileIPStatistics | 1.3.6.1.4.1.388.1.5.2.14 | |||
| STR apModelnumber | 1.3.6.1.4.1.388.1.5.1.1.1 | DisplayString | read-only | The Model Number of the Access Point device. |
| INT apModemConnected | 1.3.6.1.4.1.388.1.5.1.5.3 | INTEGER | read-write | Specifies whether the Serial Interface has a modem attached to it. Default is no(2). |
| INT apModemDialOut | 1.3.6.1.4.1.388.1.5.3.7 | INTEGER | read-write | Commands the modem to dialout (yes = 1, no = 2). |
| INT apModemHangUp | 1.3.6.1.4.1.388.1.5.3.8 | INTEGER | read-write | Forces the AP to issue a 'hangup' string to the modem attached to the serial port (yes = 1, no = 2). This command is meaning-ful only if the AP is configured for a modem connection on the serial port. If there is no modem or there is no connection, the command will be ignored. |
| INT apModemSpeaker | 1.3.6.1.4.1.388.1.5.1.5.8 | INTEGER | read-write | Specifies if modem speaker is turned on(1) or off(2). Default is on(1). |
| apMUEntry | 1.3.6.1.4.1.388.1.5.2.8.4.1 | not-accessible | An entry in the table of information for a specific MU associated with this Access Point. A row in this table cannot be created or deleted by SNMP operations on columns of the table. | |
| apMUFATEntry | 1.3.6.1.4.1.388.1.5.2.8.6.1 | not-accessible | An entry in the table of information on Mobile IP Foreign agent. A row in this table cannot be created or deleted by SNMP operations on columns of the table. | |
| apMUFrAgTable | 1.3.6.1.4.1.388.1.5.2.8.6 | not-accessible | A table of information on Mobile IP Foreign agent. The current number of entries is 127. | |
| apMUHATEntry | 1.3.6.1.4.1.388.1.5.2.8.5.1 | not-accessible | An entry in the table of information on on Mobile IP Home agent. A row in this table cannot be created or deleted by SNMP operations on columns of the table. | |
| apMUHmAgTable | 1.3.6.1.4.1.388.1.5.2.8.5 | not-accessible | A table of information on Mobile IP Home agent. The current number of entries is 127. | |
| INT apMUInactivityTimeOut | 1.3.6.1.4.1.388.1.5.1.4.15 | INTEGER | read-write | Allowable Mobile Unit inactivity time in minutes. The time out limit is from 3 to 600 minutes. Default is 60 minutes. |
| apMUInfo | 1.3.6.1.4.1.388.1.5.2.8 | |||
| OCT apMulticastMask | 1.3.6.1.4.1.388.1.5.1.4.11 | OCTET STRING | read-write | Supports broadcast download protocol for Point-of-Sale terminals that load a new operating image over the network instead of using a local non-volatile drive. The multicast mask is the top 32 bits of the MAC address and allows for a series of MAC addresses to receive multicast messages. These messages are transmitted by the AP immediately and not queued for processing at DTIM intervals. |
| INT apMUMUDisallowed | 1.3.6.1.4.1.388.1.5.1.2.20 | INTEGER | read-write | Controls inter-MU communication. When enabled(on), it will disallow one MU to talk to another MU through RF only. |
| INT apMUStateChngTrapEnable | 1.3.6.1.4.1.388.1.5.1.3.10 | INTEGER | read-write | Enables/Disables Mobile Unit State Change trap. Default is disabled(1). When not disabled, the following four (2) enterprise-specific traps will be generated and directed to trapHost1, TrapHost2 or all traphosts.: - MU Association Trap, the trap code is 111. - MU Un-association Trap, the trap code is 112. The enabled/disabled state of this trap depends on the state of apAllTrapsEnable. |
| apMUTable | 1.3.6.1.4.1.388.1.5.2.8.4 | not-accessible | A table of information for a specific MU associated with this Access Point. The current number of entries is 127. | |
| IP apMyIPAddr | 1.3.6.1.4.1.388.1.5.1.2.2 | IpAddress | read-write | The IP address for the AP. |
| PHY apMyMacAddr | 1.3.6.1.4.1.388.1.5.1.1.4 | PhysAddress | read-only | The MAC address of the Access Point. |
| CTR apNbrOfAnswers | 1.3.6.1.4.1.388.1.5.2.6.3 | Counter | read-only | Indicates the number of answer attempts by the AP. |
| CTR apNbrOfDialouts | 1.3.6.1.4.1.388.1.5.2.6.1 | Counter | read-only | Indicates the number of dialout attempts by the AP. |
| INT apNbrOfMUs | 1.3.6.1.4.1.388.1.5.2.9.1.5 | INTEGER | read-only | Indicates the number of MUs currently associated with this known AP. |
| CTR apNbrOfWLAPItfs | 1.3.6.1.4.1.388.1.5.2.11.1 | Counter | read-only | Indicates number of WLAP interfaces established. |
| STR apNetID | 1.3.6.1.4.1.388.1.5.1.4.2 | DisplayString | read-write | The current RF Network ID for the AP. The Network name can have up to 32 alphanumerical characters. |
| CTR apNPktsToAPStks | 1.3.6.1.4.1.388.1.5.2.1.1.6 | Counter | read-only | Indicates the number of packets sent from the Access Point Protocol Interface to the internal Access Point stack. This field should always be zero if the Access Point Protocol Interface is Access Point Stack. |
| CTR apNPktsToEnets | 1.3.6.1.4.1.388.1.5.2.1.1.3 | Counter | read-only | Indicates the number of packets sent from the Access Point Protocol Interface to the Ethernet Interface. This field should always be zero if the Access Point Protocol Interface is Ethernet. |
| CTR apNPktsToPpps | 1.3.6.1.4.1.388.1.5.2.1.1.4 | Counter | read-only | Indicates the number of packets sent from the Access Point Protocol Interface to the PPP Interface. This field is meaningful only if the PPP interface is enabled. |
| CTR apNPktsToRfs | 1.3.6.1.4.1.388.1.5.2.1.1.5 | Counter | read-only | Indicates the number of packets sent from the Access Point Protocol Interface to the RF Interface. If the Access Point Protocol Interface is RF, these are frames from one MU to another. |
| INT apNumberOfRetries | 1.3.6.1.4.1.388.1.5.2.12.1.2 | INTEGER | read-only | Packets with this Number of retries. Range (0..15). |
| CTR apOctetsIns | 1.3.6.1.4.1.388.1.5.2.2.1.5 | Counter | read-only | Indicates the number of good bytes received on the specified interface. |
| CTR apOctetsOuts | 1.3.6.1.4.1.388.1.5.2.2.1.6 | Counter | read-only | Indicates the number of bytes successfully transmitted on the specified interface. |
| GAU apOctInPerSec | 1.3.6.1.4.1.388.1.5.2.2.1.9 | Gauge | read-only | Indicates the number of good bytes per second received on the specified Interface. |
| GAU apOctOutPerSec | 1.3.6.1.4.1.388.1.5.2.2.1.10 | Gauge | read-only | Indicates the number of bytes per second successfully transmitted on the specified interface. |
| CTR apPacketsHistogramCounts | 1.3.6.1.4.1.388.1.5.2.12.1.3 | Counter | read-only | Counter for the packets per number of retries. |
| CTR apPacketsIns | 1.3.6.1.4.1.388.1.5.2.2.1.3 | Counter | read-only | Indicates the number of good packets received on the specified interface. |
| CTR apPacketsOuts | 1.3.6.1.4.1.388.1.5.2.2.1.4 | Counter | read-only | Indicates the number of packets successfully transmitted on the specified interface. |
| apPerformMgmt | 1.3.6.1.4.1.388.1.5.2 | |||
| GAU apPktsInPerSec | 1.3.6.1.4.1.388.1.5.2.2.1.7 | Gauge | read-only | Indicates the number of good packets per second received on the specified Interface. |
| GAU apPktsOutPerSec | 1.3.6.1.4.1.388.1.5.2.2.1.8 | Gauge | read-only | Indicates the number of packets per second successfully transmitted on the specified interface. |
| INT apPPPState | 1.3.6.1.4.1.388.1.5.1.5.1 | INTEGER | read-write | Indicates the current state of the PPP connection machine. Default is down(2). |
| CTR apPPPTerminates | 1.3.6.1.4.1.388.1.5.1.5.11 | Counter | read-write | Specifies the maximum number of PPP terminate requests. Default is 10. |
| INT apPPPTimeout | 1.3.6.1.4.1.388.1.5.1.5.10 | INTEGER | read-write | Specifies the PPP event timeout in seconds. Default is 3 seconds. |
| STR apProtoItfName | 1.3.6.1.4.1.388.1.5.2.1.1.2 | DisplayString | read-only | Access Point Protocol Interface Name (i.e. Ethernet, PPP, Radio, AP). |
| INT apRadioType | 1.3.6.1.4.1.388.1.5.1.4.36 | INTEGER | read-only | This attribute displays the type of radio installed in the Access Point. ds11-v1 Ver.1 Hardware short RF Preamble not supported. ds11-V2 Ver.2 Hardware Short RF Preamble supported. |
| INT apReassemblyTimeOut | 1.3.6.1.4.1.388.1.5.1.4.9 | INTEGER | read-write | Sets the time in 0.5 ms units before a timeout occurs during a packet re-assembly. Packet re-assemblies occur when a large Ethernet packet is fragmented into smaller wireless network packets. Range : 0...9999. Default is 9000. |
| CTR apRegReplySents | 1.3.6.1.4.1.388.1.5.2.14.3 | Counter | read-only | Counter for the number registration reply sent. |
| CTR apRegRequestRcvds | 1.3.6.1.4.1.388.1.5.2.14.2 | Counter | read-only | Counter for the number registration request received. |
| INT apResetAP | 1.3.6.1.4.1.388.1.5.3.12 | INTEGER | read-write | Forces a reset of the AP (yes = 1, no = 2). Upon reset, the AP clears all the statistics and restores the last saved configuration information. If changes are made without being saved, the AP clears those changes upon reset. |
| apRetryHistogramEntry | 1.3.6.1.4.1.388.1.5.2.12.1 | not-accessible | An entry in the table of Retry Histogram, which is based on number of packets with various retries over time. A row in this table cannot be created or deleted by SNMP operations on columns of the table. | |
| INT apRetryHistogramIndex | 1.3.6.1.4.1.388.1.5.2.12.1.1 | INTEGER | read-only | Number of retries index. Range (1..16). |
| apRetryHistogramTable | 1.3.6.1.4.1.388.1.5.2.12 | not-accessible | A table of Retry statistics, which is based on number of packets with various retries over time. The current number of entries is 16. | |
| apRFConfig | 1.3.6.1.4.1.388.1.5.1.4 | |||
| STR apRFFirmwareRev | 1.3.6.1.4.1.388.1.5.1.1.6 | DisplayString | read-only | The current revision of the Access Point radio firmware. |
| INT apRFPortState | 1.3.6.1.4.1.388.1.5.1.4.1 | INTEGER | read-write | Specifies the state of the RF Interface. Default is up(1). |
| INT apRFPreamble | 1.3.6.1.4.1.388.1.5.1.4.35 | INTEGER | read-write | This attribute is set to disabled for compatibility within the 802.11 community. Setting it to enabled shall result in performance enhancement. Default is enabled. NOTE: Only radios with version 2 hardware support RF Preamble, hence configurable to enabled state. |
| INT apRFRate11Mb | 1.3.6.1.4.1.388.1.5.1.4.31 | INTEGER | read-write | Specifies the Current state of the RF data rate. There are three options: - optional(1) - not-used(2) - required(3) Default is optional for 11 Mb/s data rate. |
| INT apRFRate1Mb | 1.3.6.1.4.1.388.1.5.1.4.34 | INTEGER | read-write | Specifies the Current state of the RF data rate. There are three options: - optional(1) - not-used(2) - required(3) Default is required for 1 Mb/s data rate. |
| INT apRFRate2Mb | 1.3.6.1.4.1.388.1.5.1.4.33 | INTEGER | read-write | Specifies the Current state of the RF data rate. There are three options: - optional(1) - not-used(2) - required(3) Default is optional for 2 Mb/s data rate. |
| INT apRFRate5_5Mb | 1.3.6.1.4.1.388.1.5.1.4.32 | INTEGER | read-write | Specifies the Current state of the RF data rate. There are three options: - optional(1) - not-used(2) - required(3) Default is optional for 5.5 Mb/S data rate. |
| apRFStatistics | 1.3.6.1.4.1.388.1.5.2.4 | |||
| INT apRFTrapEnable | 1.3.6.1.4.1.388.1.5.1.3.8 | INTEGER | read-write | Enables/Disables Access Point RF driver startup trap. Default is disabled(2). This is an enterprise-specific trap and the trap code is 101. When not disabled the trap could be directed to TrapHost1, TrapHost2 or all TrapHosts. The apAllTrapsEnable flag should be enabled for this trap to be issued. |
| STR apROCommunityName | 1.3.6.1.4.1.388.1.5.1.3.2 | DisplayString | read-write | The Read-Only community name of the SNMP command for management station accessing this Access Point (up to 31 characters). |
| INT apRootInterface | 1.3.6.1.4.1.388.1.5.2.11.4 | INTEGER | read-only | Indicates the WLAP interface leading to the Root AP. |
| INT apRootPathCost | 1.3.6.1.4.1.388.1.5.2.11.6 | INTEGER | read-only | Indicates how many hops away the current WLAP is from the Root AP. |
| OCT apRootWLAPID | 1.3.6.1.4.1.388.1.5.2.11.5 | OCTET STRING | read-only | Indicates the WLAP ID of the Root AP. It consists of 2 bytes of priority (Default is 0x8000) and 6 bytes of MAC address of the Root AP |
| STR apRWCommunityName | 1.3.6.1.4.1.388.1.5.1.3.3 | DisplayString | read-write | The Read-Write community name of the SNMP command for management station accessing this Access Point (up to 13 characters). This community name is same as the System Password or Telnet Password. For security purpose, if the management station uses the READ-ONLY community name to access this object, a string of 'xxxxx' will be returned. |
| INT apS24MobileIPEnable | 1.3.6.1.4.1.388.1.5.1.2.15 | INTEGER | read-write | Enables/Disables Spectrum24 Mobile IP support, i.e. AP will act as Mobility Agent. Default is disabled(2). |
| INT apSaveConfig | 1.3.6.1.4.1.388.1.5.4.2 | INTEGER | read-write | Saves the current configuration to NVRAM (yes = 1, no = 2). |
| INT apSaveConfigAllAPs | 1.3.6.1.4.1.388.1.5.4.5 | INTEGER | read-write | Saves the current configuration to NVRAM for all APs on this network which share the same NetID(yes = 1, no = 2). |
| apSecurityMgmt | 1.3.6.1.4.1.388.1.5.4 | |||
| STR apSerialnumber | 1.3.6.1.4.1.388.1.5.1.1.2 | DisplayString | read-only | The Serial Number of the Access Point system. |
| apSerialPortConfig | 1.3.6.1.4.1.388.1.5.1.5 | |||
| apSerialPortStatistics | 1.3.6.1.4.1.388.1.5.2.6 | |||
| INT apSerialPortUse | 1.3.6.1.4.1.388.1.5.1.5.2 | INTEGER | read-write | Specifies whether the Serial Interface is to be used as User Interface(UI) or PPP. Default is ui(2). |
| apSNMPInfo | 1.3.6.1.4.1.388.1.5.1.3 | |||
| INT apSNMPMode | 1.3.6.1.4.1.388.1.5.1.3.1 | INTEGER | read-write | Specifies the mode of the SNMP Agent operation, i.e. Disabled/Readonly/ReadWrite. Default is readwrite(3). |
| CTR apSNMPRequests | 1.3.6.1.4.1.388.1.5.1.3.13 | Counter | read-only | Indicates the number of SNMP requests to this SNMP Agent. |
| CTR apSNMPTraps | 1.3.6.1.4.1.388.1.5.1.3.14 | Counter | read-only | Indicates the number of Traps that were generated by this SNMP Agent. |
| IP apSubnetMask | 1.3.6.1.4.1.388.1.5.1.2.3 | IpAddress | read-write | The IP subnet mask for the AP. |
| apSystemConfig | 1.3.6.1.4.1.388.1.5.1.2 | |||
| INT apTelnetEnable | 1.3.6.1.4.1.388.1.5.1.2.8 | INTEGER | read-write | Enables/Disables Telnet access to the AP. Default is enabled(1). |
| IP apTFTPServer | 1.3.6.1.4.1.388.1.5.3.11 | IpAddress | read-write | The IP address for the TFTP Server. Note: IF DHCP is responded to, that IP address will take precedence and overwrite this setting. |
| INT apTFTPUpdBothFiles | 1.3.6.1.4.1.388.1.5.3.18 | INTEGER | read-write | Update Both HTML file and Firmware for this Access Point The AP HTML file will be saved in NVRAM (yes = 1, no = 2). Before issuing this command, set 'apHTMLFileName', and 'apTFTPServer' to the proper values. |
| INT apTMTableIndex | 1.3.6.1.4.1.388.1.5.2.1.1.1 | INTEGER | read-only | Access Point Traffic Matrix Table index. Range (1..5). |
| CTR apTotalAssocs | 1.3.6.1.4.1.388.1.5.2.8.3 | Counter | read-only | Indicates the total number of associations by all MUs with this AP. |
| apTrafficMatrixEntry | 1.3.6.1.4.1.388.1.5.2.1.1 | not-accessible | An entry in the table of Access Point Traffic Matrix. A row in this table cannot be created or deleted by SNMP operations on columns of the table. | |
| apTrafficMatrixTable | 1.3.6.1.4.1.388.1.5.2.1 | not-accessible | A table of Access Point Traffic Matrix which provides information on packets transmitted from one interface to another (Ethernet, PPP, radio, AP). The table also displays the number of broadcast packets transmitted from the Access Point. The current number of entries is 5. | |
| IP apTrapHost1IpAdr | 1.3.6.1.4.1.388.1.5.1.3.4 | IpAddress | read-write | Trap receiver's (i.e. Network Manager's) IP address. |
| IP apTrapHost2IpAdr | 1.3.6.1.4.1.388.1.5.1.3.15 | IpAddress | read-write | Trap receiver's (i.e. Network Manager's) IP address. |
| INT apTypeFilterEnable | 1.3.6.1.4.1.388.1.5.1.2.10 | INTEGER | read-write | Specifies the type of Access Point Type Filtering operation, i.e. Disabled/Forward/Discard. Default is disabled(1). |
| apTypeFilterEntry | 1.3.6.1.4.1.388.1.5.1.7.1 | not-accessible | An entry in the table of Type Filter. A row in this table is created by setting the value of etherType to Ethernet packet type in hexadecimal. A row in this table is deleted by setting the value of etherType to 00 | |
| apTypeFilterTable | 1.3.6.1.4.1.388.1.5.1.7 | not-accessible | A table of Ethernet types (i.e. 16-bit DIX Ethernet type), which are entered by the user and supported for the type filtering function. The maximum number of entries in the table is 16. | |
| CTR apTypeViolations | 1.3.6.1.4.1.388.1.5.2.10.2 | Counter | read-only | Indicates the number of Ethernet packet type violations counted. |
| STR apUnitName | 1.3.6.1.4.1.388.1.5.1.2.1 | DisplayString | read-write | An ASCII string to identify this Access Point (up to 31 characters). |
| INT apUpdAllAPsFirmware | 1.3.6.1.4.1.388.1.5.3.16 | INTEGER | read-write | Update all APs firmware on this network which share the same NetID through TFTP server. The AP firmware will be saved in NVRAM (yes = 1, no = 2). Before issuing this command, set 'apDnLdFileName', and 'apTFTPServer' to the proper values. |
| INT apUpdAllAPsHTMLFile | 1.3.6.1.4.1.388.1.5.3.17 | INTEGER | read-write | Update all APs HTML file on this network which share the same NetID through TFTP server. The AP HTML file will be saved in NVRAM (yes = 1, no = 2). Before issuing this command, set 'apHTMLFileName', and 'apTFTPServer' to the proper values. |
| INT apUpdateFirmware | 1.3.6.1.4.1.388.1.5.3.9 | INTEGER | read-write | Update the AP firmware through TFTP server. The AP firmware will be saved in NVRAM (yes = 1, no = 2). Before issuing this command, set 'apDnLdFileName', and 'apTFTPServer' to the proper values. |
| INT apUpdateHTMLFile | 1.3.6.1.4.1.388.1.5.3.14 | INTEGER | read-write | Update the AP HTML file through TFTP server. The AP HTML file will be saved in NVRAM (yes = 1, no = 2). Before issuing this command, set 'apHTMLFileName', and 'apTFTPServer' to the proper values. |
| INT apVendorID | 1.3.6.1.4.1.388.1.5.1.1.9 | INTEGER | read-only | Displays the Vendor ID of the vendor for which this AP has been manufactured for. The current values are: - Symbol (5) - 3Com (6) - Ericsson (8) - Intel (9) |
| INT apWebServerEnable | 1.3.6.1.4.1.388.1.5.1.2.17 | INTEGER | read-write | Enables/Disables Access Point Web Server. When enabled, the Access Point will serve Web clients. Default is enabled(1) |
| INT apWEPAlgorithm | 1.3.6.1.4.1.388.1.5.1.4.30 | INTEGER | read-write | This attribute is a set of all the shared key WEP algorithms supported by the STAs. The following are the default values and the associated algorithm. Value = 1: 128 bit Key Value = 2: 40 bit Key. IMPORTANT NOTE: The 128 bit WEP key ENcryption is currently restricted by U.S. laws. In order to activate the 128 bit Encryption, an authentic License key has to be obtained and entered through one of the interfaces such as Telnet, SNMP or Web. Upon authentication of the key the AP will enable the 128 bit ENcryption. See Access Point manual for details. |
| apWEPKeyEntry | 1.3.6.1.4.1.388.1.5.1.8.1 | not-accessible | An entry in the table of Default WEP Keys. | |
| STR apWEPLicenseKey | 1.3.6.1.4.1.388.1.5.4.6 | DisplayString | read-write | This is a license key (a string of 18 alphanumeric characters). It is arranaged as follows: xxxx-yyyyyyy-zzzzzzz xxxx : vendor specific ID code ( 4 alphabetical characters) -yyyyyyy-zzzzzzz : a string of 14 alphanumeric characters Note: It is important to insert the hyphens in as shown. When entered and authenticated by the AP, the Strong(128 bit) encryption is enabled. Check the state of ap128bWEPFlag object. |
| INT apWLAPConnChngTrapEnable | 1.3.6.1.4.1.388.1.5.1.3.11 | INTEGER | read-write | When Enabled, if there are any WLAP Connection Change, one of four (4) following enterprise-specific traps will be issued. - Root AP Up Trap, the trap code is 121. - Root AP Lost Trap, the trap code is 122. - Designated WLAP Up Trap, the trap code is 123. - Designated WLAP Lost Trap, the trap code is 124. Default is disabled(2). When not disabled the trap could be directed to TrapHost1, TrapHost2 or all TrapHosts. The apAllTrapsEnable flag should be enabled for this trap to be issued. |
| INT apWLAPFwdDelay | 1.3.6.1.4.1.388.1.5.1.4.21 | INTEGER | read-write | Specifies how long, in seconds, an WLAP is prevented from forwarding data packets to an interface. This delay is to allow the spread of news of a topology change to all parts of a network. Default is 5 seconds. Reset AP for value to take effect. Range: 0..9999. |
| INT apWLAPHelloTime | 1.3.6.1.4.1.388.1.5.1.4.19 | INTEGER | read-write | Sets the time lapse, in seconds, between Configuration BPDUs (Bridge Protocol Data Unit) sent to the Root AP by a designated WLAP to indicate that it is still alive. Default is 20 seconds. Reset AP for value to take effect. Range: 0..9999. |
| INT apWLAPHopSequence | 1.3.6.1.4.1.388.1.5.2.11.3 | INTEGER | read-only | Indicates the hop sequence of the Root AP followed by this WLAP. |
| OCT apWLAPID | 1.3.6.1.4.1.388.1.5.2.11.7 | OCTET STRING | read-only | Indicates the WLAP ID of the current WLAP. It consists of 2 bytes of priority (Default is 0x8000) and 6 bytes MAC address of the current WLAP |
| apWLAPInfo | 1.3.6.1.4.1.388.1.5.2.11 | |||
| PHY apWLAPItfAddr | 1.3.6.1.4.1.388.1.5.2.11.8.1.2 | PhysAddress | read-only | The MAC address of the associated WLAP on this interface. |
| apWLAPItfEntry | 1.3.6.1.4.1.388.1.5.2.11.8.1 | not-accessible | An entry in the table of wireless AP interfaces information. | |
| OCT apWLAPItfID | 1.3.6.1.4.1.388.1.5.2.11.8.1.1 | OCTET STRING | read-only | WLAP interface ID. It consists of 1 byte of priority (Default is 0x80) and 1 byte of interface ID. |
| INT apWLAPItfState | 1.3.6.1.4.1.388.1.5.2.11.8.1.3 | INTEGER | read-only | The current state of the Wireless AP interface, ie : Disabled(1), Listening(2), Learning(3), Forwarding(4), or Blocking(5). |
| apWLAPItfTable | 1.3.6.1.4.1.388.1.5.2.11.8 | not-accessible | A table of wireless AP interfaces information, which contains four (4) AP-to-AP interfaces. | |
| PHY apWLAPManualBSSID | 1.3.6.1.4.1.388.1.5.1.4.18 | PhysAddress | read-write | Specifies the BSS-ID of a particular WLAP and forces the current WLAP to associate only with that WLAP. When WLAP Manaul BSS ID is set to the current WLAP MAC address, the current WLAP jumps into Functional state immediately and waits for an Association Request from the other WLAP. Reset AP for value to take effect. |
| INT apWLAPMaxAge | 1.3.6.1.4.1.388.1.5.1.4.20 | INTEGER | read-write | Specifies how long, in seconds, a Configuration BPDU (Bridge Protocol Data Unit) is kept by the Root AP before it is judged too old and discarded. Consequently, the interface is considered to be disconnected. Default is 100 seconds. Recommended value is multiple of the WLAP Hello Time. Reset AP for value to take effect. Range: 0..9999. |
| INT apWLAPMode | 1.3.6.1.4.1.388.1.5.1.4.16 | INTEGER | read-write | Enables/Disables Wireless AP capability and set link required option to wireless AP. Once in link-required mode, upon power-up, Root AP requires connection to the Ethernet cable and WLAP requires association with the Root AP and WLAP will keep probing forever. Default is disabled(2). |
| INT apWLAPPathCost | 1.3.6.1.4.1.388.1.5.2.11.8.1.4 | INTEGER | read-only | The cost to be added to the root path cost field in the config BPDU (Bridge Protocol Data Unit) received on this interface in order to determine the cost of the path to the root WLAP. |
| OCT apWLAPPriority | 1.3.6.1.4.1.388.1.5.1.4.17 | OCTET STRING | read-write | Provides a user with the influence to determine the Root AP in wireless operation. The priority value is added as the most significant portion of the MAC address to form the WLAP ID. A WLAP with a lower numerical value for priority is more likely to become the Root AP. Priority 0xFFFF is special. It grants the WLAP with roaming capability. Default is 8000 hex from the 0 - 0xFFFF range. Reset AP for value to take effect. |
| INT apWLAPState | 1.3.6.1.4.1.388.1.5.2.11.2 | INTEGER | read-only | Indicates the current WLAP state. The state values and meanings are as follows: - During power-up initialization: Initializing(1) - During WLAP association process: send-probe(2) send-assoc-req(3) send-cfg-bpdu(4) wait-for-probe(5) send-probe-rsp(6) send-assoc-rsp(7) send-cfg-rsp(8) receive-root-rsp(10) - During WLAP operation: root-ap-lost(12) disabled(14) functional(15) wlap-lost-on-ethernet(16) |
| CTR apWNMPCfgPkts | 1.3.6.1.4.1.388.1.5.2.7.1 | Counter | read-only | Indicates the number of WNMP configuration requests received from NetVision. |
| INT apWNMPEnable | 1.3.6.1.4.1.388.1.5.1.2.13 | INTEGER | read-write | Enables/Disables Use of the WNMP agent. Default is enabled(1). |
| apWNMPStatistics | 1.3.6.1.4.1.388.1.5.2.7 | |||
| NTF authenticationFailure | 1.3.6.1.2.1.11.0.4 | Invalid SNMP Community string. - apMyMacAddr is the MAC address of the Access Point sending this trap message. - apAPMacAddr is the MAC address of the remote host sending SNMP packet with invalid community. | ||
| NTF coldStart | 1.3.6.1.2.1.11.0.0 | Access Point cold boot. - apMyMacAddr is the MAC address of the Access Point sending this trap message. | ||
| INT disallowedIndex | 1.3.6.1.4.1.388.1.5.1.6.1.1 | INTEGER | read-only | Address Filter Table index. Range (1..512). |
| PHY disallowedMU | 1.3.6.1.4.1.388.1.5.1.6.1.2 | PhysAddress | read-write | MU MAC address which is not allowed to be associated with this Access Point. |
| dsap | 1.3.6.1.4.1.388.1.5 | |||
| OCT etherType | 1.3.6.1.4.1.388.1.5.1.7.1.2 | OCTET STRING | read-write | A 16-bit Ethernet Protocol Type in hexadecimal. Range of valid Entries: 0X05DD .. 0XFFFE |
| PHY highMacAddr | 1.3.6.1.4.1.388.1.5.4.4.1.3 | PhysAddress | read-write | The highest Mobile Unit MAC address in the range which is allowed to be associated with this AP. Note: When setting the ACL range, Both lowMacAddr and highMacAddr have to be set in order for the ACL range setting to take effect. highMacAddr should be entered last. highMacAddr > lowMacAddr |
| PHY lowMacAddr | 1.3.6.1.4.1.388.1.5.4.4.1.2 | PhysAddress | read-write | The lowest Mobile Unit MAC address in the range which is allowed to be associated with this AP. Note: When setting the ACL range, Both lowMacAddr and highMacAddr have to be set in order for the ACL range setting to take effect. lowMacAddr should be entered first. lowMacAddr < highMacAddr |
| TIK muAssocStart | 1.3.6.1.4.1.388.1.5.2.8.4.1.9 | TimeTicks | read-only | Indicates when the MU began its current association with this AP. Note: Time is represented in seconds and the time is relative to the boot time of this AP. This is also true for all the association objects listed below. |
| INT muCurrentXmtRate | 1.3.6.1.4.1.388.1.5.2.8.4.1.20 | INTEGER | read-only | Indicates the current transmit data rate for this MU. The unit is MB/second. |
| IP muFATHmAgIpAddr | 1.3.6.1.4.1.388.1.5.2.8.6.1.2 | IpAddress | read-only | This is the IP Address of the home agent for the visiting MU. |
| IP muFATMUIpAddr | 1.3.6.1.4.1.388.1.5.2.8.6.1.1 | IpAddress | read-only | This is the IP Address of the MU visiting in the foreign network. |
| IP muHATFrAgIpAddr | 1.3.6.1.4.1.388.1.5.2.8.5.1.2 | IpAddress | read-only | This is the IP Address of the Foreign agent for the visiting MU. |
| IP muHATMUIpAddr | 1.3.6.1.4.1.388.1.5.2.8.5.1.1 | IpAddress | read-only | This is the IP Address of the MU visiting in the foreign network. |
| INT muIndex | 1.3.6.1.4.1.388.1.5.2.8.4.1.1 | INTEGER | read-only | Specific MU information Table index. Range (1..127). |
| INT muInterface | 1.3.6.1.4.1.388.1.5.2.8.4.1.3 | INTEGER | read-only | Indicates the interface on which this MU is located. Note: The AP may learn of an MU via the RF network or from the wired networks such as Ethernet or PPP. In this release, the AP does not keep track of those MUs reachable via the Ethernet, but that will change in future releases. |
| TIK muLastActivity | 1.3.6.1.4.1.388.1.5.2.8.4.1.21 | TimeTicks | read-only | Indicates the time for the last activity for this MU. |
| PHY muLastAPAddr | 1.3.6.1.4.1.388.1.5.2.8.4.1.7 | PhysAddress | read-only | Indicates the MAC address of the last AP with which this MU had an association. |
| TIK muLastAssEnd | 1.3.6.1.4.1.388.1.5.2.8.4.1.11 | TimeTicks | read-only | Indicates when the MU ended its previous association with this AP. If this is the first association with this AP, this value is zero. |
| TIK muLstAssStrt | 1.3.6.1.4.1.388.1.5.2.8.4.1.10 | TimeTicks | read-only | Indicates when the MU began its prior association with this AP. If this is the first association with this AP, this value is zero. |
| PHY muMacAddr | 1.3.6.1.4.1.388.1.5.2.8.4.1.2 | PhysAddress | read-only | The MAC address of the MU associated with this AP. |
| CTR muNBytesRcvds | 1.3.6.1.4.1.388.1.5.2.8.4.1.15 | Counter | read-only | Indicates the number of Good Bytes received from this MU. |
| CTR muNBytesSents | 1.3.6.1.4.1.388.1.5.2.8.4.1.14 | Counter | read-only | Indicates the number of bytes successfully transmitted to this MU. |
| CTR muNDiscdPkts | 1.3.6.1.4.1.388.1.5.2.8.4.1.16 | Counter | read-only | Indicates the number of received packets discarded because no buffers. |
| CTR muNPktsRcvds | 1.3.6.1.4.1.388.1.5.2.8.4.1.13 | Counter | read-only | Indicates the number of Good Packets received from this MU. |
| CTR muNPktsSents | 1.3.6.1.4.1.388.1.5.2.8.4.1.12 | Counter | read-only | Indicates the number of packets successfully transmitted to this MU. |
| INT muPowerMode | 1.3.6.1.4.1.388.1.5.2.8.4.1.5 | INTEGER | read-only | Indicates the MU power mode (Power Save Protocol mode or Continue Active Mode.) |
| INT muPriority | 1.3.6.1.4.1.388.1.5.2.8.4.1.18 | INTEGER | read-only | Indicates the Voice/Data priority mode for this MU. |
| INT muState | 1.3.6.1.4.1.388.1.5.2.8.4.1.4 | INTEGER | read-only | Indicates the state of this MU. |
| INT muStationID | 1.3.6.1.4.1.388.1.5.2.8.4.1.6 | INTEGER | read-only | Indicates the MU station ID. |
| INT muSupportedRates | 1.3.6.1.4.1.388.1.5.2.8.4.1.19 | INTEGER | read-only | Indicates the supported data rates for this MU. The unit is MB/second. |
| TIK muTmLastData | 1.3.6.1.4.1.388.1.5.2.8.4.1.17 | TimeTicks | read-only | Indicates the time when the last good packet was received from this MU. The packet may be either an ACK, Data, or Poll. |
| INT muTotalAssoc | 1.3.6.1.4.1.388.1.5.2.8.4.1.8 | INTEGER | read-only | Indicates the total associations for this MU. |
| CTR rfAssocMUs | 1.3.6.1.4.1.388.1.5.2.4.15 | Counter | read-only | Indicates the number of MUs currently associated with this AP. |
| CTR rfBcMcOctRcvds | 1.3.6.1.4.1.388.1.5.2.4.4 | Counter | read-only | Indicates the number of broadcast/multicast bytes that have been successfully received. |
| CTR rfBcMcOctSents | 1.3.6.1.4.1.388.1.5.2.4.3 | Counter | read-only | Indicates the number of broadcast/multicast bytes that have been successfully transmitted. |
| CTR rfBcMcPktsRcvds | 1.3.6.1.4.1.388.1.5.2.4.2 | Counter | read-only | Indicates the number of broadcast/multicast packets that have been successfully received. |
| CTR rfBcMcPktsSents | 1.3.6.1.4.1.388.1.5.2.4.1 | Counter | read-only | Indicates the number of broadcast/multicast packets that have been successfully transmitted. |
| CTR rfDataOctetsRcvds | 1.3.6.1.4.1.388.1.5.2.4.25 | Counter | read-only | Indicates the number of octets that were successfully received. |
| CTR rfDataOctetsSents | 1.3.6.1.4.1.388.1.5.2.4.24 | Counter | read-only | Indicates the number of octets transmitted. |
| CTR rfDataPktsRcvds | 1.3.6.1.4.1.388.1.5.2.4.23 | Counter | read-only | Indicates the number of packets that were successfully received. |
| CTR rfDataPktsSents | 1.3.6.1.4.1.388.1.5.2.4.22 | Counter | read-only | Indicates the number of packets transmitted. |
| INT rfDSFrequency | 1.3.6.1.4.1.388.1.5.2.13.1.1 | INTEGER | read-only | Radio Frequency channel number. |
| CTR rfDSPerFqPktsRcvds | 1.3.6.1.4.1.388.1.5.2.13.1.3 | Counter | read-only | Counter for the packets received per frequency. |
| CTR rfDSPerFqPktsSents | 1.3.6.1.4.1.388.1.5.2.13.1.2 | Counter | read-only | Counter for the packets sent per frequency. |
| CTR rfDSPerFqRetries | 1.3.6.1.4.1.388.1.5.2.13.1.4 | Counter | read-only | Counter for the retries per frequency. |
| CTR rfEncrypPktsRcvds | 1.3.6.1.4.1.388.1.5.2.4.27 | Counter | read-only | Indicates the number of Encrypted packets that were successfully received. |
| CTR rfEncrypPktsSents | 1.3.6.1.4.1.388.1.5.2.4.26 | Counter | read-only | Indicates the number of Encrypted packets transmitted. |
| CTR rfPktsWithColls | 1.3.6.1.4.1.388.1.5.2.4.21 | Counter | read-only | Indicates the number of packets that suffered at least one collision. |
| CTR rfPktsWithMaxColls | 1.3.6.1.4.1.388.1.5.2.4.20 | Counter | read-only | Indicates the number of packets that suffered the maximum number of collisions. |
| CTR rfPktsWithoutColls | 1.3.6.1.4.1.388.1.5.2.4.19 | Counter | read-only | Indicates the number of packets without any collision. |
| CTR rfRcvdCRCErrors | 1.3.6.1.4.1.388.1.5.2.4.16 | Counter | read-only | Indicates the number of packets that were received but had the CRC errors. |
| CTR rfRcvdDupPkts | 1.3.6.1.4.1.388.1.5.2.4.17 | Counter | read-only | Indicates the number of packets that were received but were duplicates of previously received. This is usually an indication that an ACK was not received by the sending unit. |
| CTR rfSBcMcPktsRcvds | 1.3.6.1.4.1.388.1.5.2.4.8 | Counter | read-only | Indicates the number of system broadcast/multicast (includes beacons) packets that have been successfully received. |
| CTR rfSBcMcPktsSents | 1.3.6.1.4.1.388.1.5.2.4.7 | Counter | read-only | Indicates the number of system broadcast/multicast packets (includes beacons) that have been successfully transmitted. |
| CTR rfSuccFragPkts | 1.3.6.1.4.1.388.1.5.2.4.9 | Counter | read-only | Indicates the number of packets that were fragmented and for which all fragments were acked. |
| CTR rfSuccReassPkts | 1.3.6.1.4.1.388.1.5.2.4.13 | Counter | read-only | Indicates the number of packets that were reassigned and successfully reassembled. |
| CTR rfSysPktsRcvds | 1.3.6.1.4.1.388.1.5.2.4.6 | Counter | read-only | Indicates the number of system packets (includes probes /associate packets) that have been successfully received. |
| CTR rfSysPktsSents | 1.3.6.1.4.1.388.1.5.2.4.5 | Counter | read-only | Indicates the number of system packets (includes probe operations packets) that have been successfully transmitted. |
| CTR rfTotalCollisions | 1.3.6.1.4.1.388.1.5.2.4.18 | Counter | read-only | Indicates the number of collisions that have occured on the interface. A collision on the RF interface means that an ack was not received or that a RTS was not answered by a CTS. |
| CTR rfTotalFragRcvds | 1.3.6.1.4.1.388.1.5.2.4.12 | Counter | read-only | Indicates the number of packets fragments that have been received. |
| CTR rfTotalFragSents | 1.3.6.1.4.1.388.1.5.2.4.11 | Counter | read-only | Indicates the number of packets fragments that have been sent. |
| CTR rfUnsuccFragPkts | 1.3.6.1.4.1.388.1.5.2.4.10 | Counter | read-only | Indicates the number of packets that were fragmented but for which one or more fragments were not acked. |
| CTR rfUnsuccReassPkts | 1.3.6.1.4.1.388.1.5.2.4.14 | Counter | read-only | Indicates the number of packets that were unsuccessfully reassembled. |
| spectrum24 | 1.3.6.1.4.1.388.1 | |||
| symbol | 1.3.6.1.4.1.388 | |||
| INT typeIndex | 1.3.6.1.4.1.388.1.5.1.7.1.1 | INTEGER | read-only | Filter Type Table index. Range (1..16). |
| CTR wEchoRequests | 1.3.6.1.4.1.388.1.5.2.7.2 | Counter | read-only | Indicates the number of WNMP Echo Requests received by this AP. |
| CTR wPassThruEchoes | 1.3.6.1.4.1.388.1.5.2.7.6 | Counter | read-only | Indicates the number of WNMP packets for other stations that passed through this AP. |
| CTR wPingRequests | 1.3.6.1.4.1.388.1.5.2.7.3 | Counter | read-only | Indicates the number of WNMP ping requests received by this AP. |
| CTR wPktsFromNVs | 1.3.6.1.4.1.388.1.5.2.7.4 | Counter | read-only | Indicates the number of WNMP packets that were received from NetVision via this AP. |
| CTR wPPktsToNVs | 1.3.6.1.4.1.388.1.5.2.7.5 | Counter | read-only | Indicates the number of WNMP packets that were sent to the NetVision via this AP. |
RFC description
Manages Symbol Spectrum24 Direct Sequence wireless access point configuration, manufacture info, and SNMP settings.
Start monitoring Symbol Technologies (Motorola/Zebra) 802.11 DSSS access point (hardware/firmware identity, network config) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.