All MIBs › GDC7616-MIB
Category: Vendor: GDC
Description: General DataComm 7616 multiplexer MIB for chassis slot, port, and cross-connect configuration management.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is GDC7616-MIB?
GDC7616-MIB is a vendor-specific MIB from General DataComm for its UAS 7616 multiplexer/access chassis, a telecom carrier-grade multiplexing platform. It exposes chassis identification (device type via a WhatAreYou table), system alarm status, timing generator status, and per-slot/port configuration data such as clock source and line termination type. It supports hardware and software status monitoring through uas7616AlarmStatus and uas7616SystemTimingGenStatus, letting operators detect chassis-level faults, timing reference loss, or firmware revision mismatches (uas7616CodeRev) across slots. It is a self-contained proprietary MIB with no explicit dependency noted beyond standard SNMPv2 SMI conventions under the gdc/bql2 enterprise branches. It is typically deployed in legacy telecom/datacom environments where GDC 7616 multiplexers provide TDM cross-connect and channelization services. Engineers can download the GDC7616-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in GDC7616-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- General DataComm UAS 7616 multiplexer
- telecom TDM access/multiplexing chassis
Monitoring Examples
An operator would poll uas7616AlarmStatus and uas7616SystemTimingGenStatus to confirm the chassis clock reference is locked and no alarms are active, since a non-zero alarm status typically indicates a card failure or loss of signal. Walking uas7616ConfigTable/uas7616ConfigEntry (indexed by uas7616ConfigIndex) surfaces per-port settings like uas7616TXClockSource and uas7616TerminationType, letting staff verify a port's timing source matches the intended design. uas7616WhatAreYouTable identifies installed card types by uas7616WhatAreYouIndex, useful for confirming chassis inventory against uas7616CodeRev firmware levels.
What Can Be Monitored
- chassis alarm status
- timing generator/clock lock status
- firmware/code revision
- per-port clock source configuration
- port termination type
- installed card/module identity
This MIB depends on
Related MIBs
Imported Objects
From GDCMACRO-MIB
| SCinstance |
From RFC-1212
| OBJECT-TYPE |
From RFC1155-SMI
| enterprises |
From RFC1213-MIB
| DisplayString |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| bql2 | 1.3.6.1.4.1.498.12 | |||
| gdc | 1.3.6.1.4.1.498 | |||
| uas7616 | 1.3.6.1.4.1.498.12.4 | |||
| uas7616Alarm | 1.3.6.1.4.1.498.12.13 | |||
| uas7616AlarmConfigEntry | 1.3.6.1.4.1.498.12.13.2.1 | not-accessible | An entry in the GDC Alarm Configuration table. | |
| OID uas7616AlarmConfigIdentifier | 1.3.6.1.4.1.498.12.13.2.1.2 | OBJECT IDENTIFIER | read-only | The unique alarm identifier assigned to this alarm type. The format of this identifier is an OBJECT IDENTIFIER that has the following format: {iso(1) org(3) dod(6) internet(1) private(4) enterprises(1) gdc(498) xxx(x) alarm(z) yyy(y) where xxx(x) is the administratively assigned family object identifier (z) is the object identifier for alarms in the family defined MIB and yyy(y) is the administratively assigned alarm type identifier for this alarm. |
| SCI uas7616AlarmConfigIndex | 1.3.6.1.4.1.498.12.13.2.1.1 | SCinstance | read-only | The index value which uniquely identifies the interface to which this entry is applicable. |
| uas7616AlarmConfigTable | 1.3.6.1.4.1.498.12.13.2 | not-accessible | The uas7616AlarmConfigTable contains entries that configure alarm reporting. The structure of the table is such that alarm configuration is supported on a unit and interface basis, and then on an alarm type basis within the interface. For simplicity sake alarms, be they unit or interface related, are represented in one table. | |
| INT uas7616AlarmCountThreshold | 1.3.6.1.4.1.498.12.13.2.1.4 | INTEGER | read-write | This function sets/reads the UAS, SES or ES alarm threshold criteria. This threshold is used along with the the alarm window to determine the number of instances in a given time frame for an alarm to occur before the alarm is considered active. |
| INT uas7616AlarmCountWindow | 1.3.6.1.4.1.498.12.13.2.1.3 | INTEGER | read-write | This variable sets/reads the UAS, SES or ES alarm window. This window is used with the alarm threshold to determine how long the alarm should be active before reporting. |
| uas7616AlarmData | 1.3.6.1.4.1.498.12.13.1 | |||
| OCT uas7616AlarmStatus | 1.3.6.1.4.1.498.12.4.2.1.3 | OCTET STRING | read-only | The current alarms of the unit without the alarm masks. |
| INT uas7616ChADataRate | 1.3.6.1.4.1.498.12.4.3.1.4 | INTEGER | read-write | Object to select the Data Rate on Channel A, Loop n. |
| INT uas7616ChannelIndex | 1.3.6.1.4.1.498.12.4.15.1.2 | INTEGER | read-write | The index value which uniquely identifies the channel of the interface to which this entry is applicable. |
| INT uas7616ChBDataRate | 1.3.6.1.4.1.498.12.4.3.1.5 | INTEGER | read-write | Object to select the Data Rate on Channel B, Loop n. |
| STR uas7616CodeRev | 1.3.6.1.4.1.498.12.4.2.1.2 | DisplayString | read-only | This function returns the firmware code level. Example A- ,B- |
| uas7616ConfigEntry | 1.3.6.1.4.1.498.12.4.3.1 | not-accessible | A listing of GDC 2B1Q 7616 options. | |
| SCI uas7616ConfigIndex | 1.3.6.1.4.1.498.12.4.3.1.1 | SCinstance | read-only | A unique index for the Configuration Table. |
| uas7616ConfigTable | 1.3.6.1.4.1.498.12.4.3 | not-accessible | The GDC 7616 configuration table. | |
| uas7616ControlEntry | 1.3.6.1.4.1.498.12.4.5.1 | not-accessible | An entry in the GDC 7616 Control table. | |
| SCI uas7616ControlIndex | 1.3.6.1.4.1.498.12.4.5.1.1 | SCinstance | read-only | This object is the identifier of the 7616 Control table. |
| uas7616ControlTable | 1.3.6.1.4.1.498.12.4.5 | not-accessible | The GDC 7616 Control Table. | |
| uas7616Current15MinEntry | 1.3.6.1.4.1.498.12.4.8.1 | not-accessible | An entry in the 7616 Current table. | |
| SCI uas7616Current15MinIndex | 1.3.6.1.4.1.498.12.4.8.1.1 | SCinstance | read-only | The index value which uniquely identifies the interface to which this entry is applicable. This has the form of a SCinstance which defines the slot, line, drop, and interface. |
| OCT uas7616Current15MinStat | 1.3.6.1.4.1.498.12.4.8.1.2 | OCTET STRING | read-only | Returns a bitwise snapshot of the interval statistics. Octet 1 bit 7 - not used bit 6 - future use bit 5 - future use bit 4 - future use bit 3 - future use bit 2 - future use bit 1 - 2^1 bit 0 - 2^0 Loop ID Octet 2 bit 7 - not used bit 6 - future use bit 5 - future use bit 4 - future use bit 3 - future use bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 3 bit 7 - not used bit 6 - 2^6 bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Errored Seconds Octet 4 bit 7 - not used bit 6 - future use bit 5 - future use bit 4 - future use bit 3 - future use bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 5 bit 7 - not used bit 6 - 2^6 bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Severely Errored Seconds Octet 6 bit 7 - not used bit 6 - future use bit 5 - future use bit 4 - future use bit 3 - future use bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 7 bit 7 - not used bit 6 - 2^6 bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Unavailable Seconds Octet 8 bit 7 - not used bit 6 - future use bit 5 - future use bit 4 - future use bit 3 - future use bit 2 - 2^16 bit 1 - 2^15 bit 0 - 2^14 Octet 9 bit 7 - not used bit 6 - 2^13 bit 5 - 2^12 bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 10 bit 7 - not used bit 6 - 2^6 bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 FEBE (Far End Block Error Count) (not available on network element type 30) |
| uas7616Current15MinTable | 1.3.6.1.4.1.498.12.4.8 | not-accessible | The 7616 15 Min Current table. | |
| uas7616Current24HrEntry | 1.3.6.1.4.1.498.12.4.10.1 | not-accessible | An entry in the Current24Hr table. | |
| SCI uas7616Current24HrIndex | 1.3.6.1.4.1.498.12.4.10.1.1 | SCinstance | read-only | The index value which uniquely identifies the interface to which this entry is applicable. This has the form of a SCinstance which defines the slot, line, drop, and interface. |
| OCT uas7616Current24HrStat | 1.3.6.1.4.1.498.12.4.10.1.2 | OCTET STRING | read-only | Returns a bitwise snapshot of the interval statistics. Octet 1 bit 7 - not used bit 6 - future use bit 5 - future use bit 4 - future use bit 3 - future use bit 2 - future use bit 1 - 2^1 bit 0 - 2^0 Loop ID Octet 2 bit 7 - not used bit 6 - future use bit 5 - future use bit 4 - future use bit 3 - future use bit 2 - >65535 bit 1 - 2^15 bit 0 - 2^14 Octet 3 bit 7 - not used bit 6 - 2^13 bit 5 - 2^12 bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 4 bit 7 - not used bit 6 - 2^6 bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Errored Seconds Octet 5 bit 7 - not used bit 6 - future use bit 5 - future use bit 4 - future use bit 3 - future use bit 2 - >65535 bit 1 - 2^15 bit 0 - 2^14 Octet 6 bit 7 - not used bit 6 - 2^13 bit 5 - 2^12 bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 7 bit 7 - not used bit 6 - 2^6 bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Severely Errored Seconds Octet 8 bit 7 - not used bit 6 - future use bit 5 - future use bit 4 - future use bit 3 - future use bit 2 - >65535 bit 1 - 2^15 bit 0 - 2^14 Octet 9 bit 7 - not used bit 6 - 2^13 bit 5 - 2^12 bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 10 bit 7 - not used bit 6 - 2^6 bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Unavailable Seconds Octet 11 bit 7 - not used bit 6 - future use bit 5 - future use bit 4 - future use bit 3 - future use bit 2 - 2^23 bit 1 - 2^22 bit 0 - 2^21 Octet 12 bit 7 - not used bit 6 - 2^20 bit 5 - 2^19 bit 4 - 2^18 bit 3 - 2^17 bit 2 - 2^16 bit 1 - 2^15 bit 0 - 2^14 Octet 13 bit 7 - not used bit 6 - 2^13 bit 5 - 2^12 bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 14 bit 7 - not used bit 6 - 2^6 bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 FEBE (Far End Block Error Count) (not available on network element type 30) |
| uas7616Current24HrTable | 1.3.6.1.4.1.498.12.4.10 | not-accessible | The Current24Hr table. 4 hour interval. | |
| INT uas7616DiagnosticChnlIndex | 1.3.6.1.4.1.498.12.4.6.1.2 | INTEGER | read-only | A unique channel index for the Channel the test will run on. |
| uas7616DiagnosticEntry | 1.3.6.1.4.1.498.12.4.6.1 | not-accessible | A listing of GDC 7616 diagnostic tests | |
| SCI uas7616DiagnosticIndex | 1.3.6.1.4.1.498.12.4.6.1.1 | SCinstance | read-only | A unique index for the Diagnostic Table. |
| INT uas7616DiagnosticResetErrorCount | 1.3.6.1.4.1.498.12.4.6.1.4 | INTEGER | read-write | This function resets the error count on a given loop and channel. Management will always read a norm(1) and can only write a reset(2). |
| INT uas7616DiagnosticResults | 1.3.6.1.4.1.498.12.4.6.1.5 | INTEGER | read-only | This function reads the self test results in bit errors. 2^20 |
| uas7616DiagnosticTable | 1.3.6.1.4.1.498.12.4.6 | not-accessible | The GDC 7616 diagnostics table. | |
| INT uas7616DiagnosticTest | 1.3.6.1.4.1.498.12.4.6.1.3 | INTEGER | read-write | Selections digitalLoopback(2), patternGenTest(3), and unitTest(4) start the associated test when written. Reading will show which (if any) test is active. Writing a stopTestwill stop the test if any was in progress. |
| uas7616DiagRxErrAlm | 1.3.6.1.4.1.498.12.13.1.2 | |||
| INT uas7616EraseConfig | 1.3.6.1.4.1.498.12.4.5.1.3 | INTEGER | read-write | Forces an erase of the stored configuration in the network element. The erase selection is write only. |
| INT uas7616Highway | 1.3.6.1.4.1.498.12.4.15.1.3 | INTEGER | read-write | Defines the highway the channel of the loop is assigned to. |
| INT uas7616InterfaceType | 1.3.6.1.4.1.498.12.4.5.1.5 | INTEGER | read-write | Object used to configure the transmission interface type. |
| uas7616IntervalEntry | 1.3.6.1.4.1.498.12.4.9.1 | not-accessible | An entry in the Interval table. | |
| SCI uas7616IntervalIndex | 1.3.6.1.4.1.498.12.4.9.1.1 | SCinstance | read-only | The index value which uniquely identifies the interface to which this entry is applicable. This has the form of a SCinstance which defines the slot, line, drop, and interface. |
| uas7616IntervalMaintenanceEntry | 1.3.6.1.4.1.498.12.4.13.1 | not-accessible | The 7616 Interval Maintenance table entry. | |
| SCI uas7616IntervalMaintenanceIndex | 1.3.6.1.4.1.498.12.4.13.1.1 | SCinstance | read-only | The index value which uniquely identifies the interface to which this entry is applicable. This has the form of a SCinstance which defines the slot, line, drop, and interface, which in this case is a Loop interface. |
| uas7616IntervalMaintenanceTable | 1.3.6.1.4.1.498.12.4.13 | not-accessible | The 7616 Loop Interval Maintenance table. | |
| INT uas7616IntervalNumber | 1.3.6.1.4.1.498.12.4.9.1.2 | INTEGER | read-only | The number of Errored Seconds, Unavailable Seconds & Severely Errored Seconds encountered in one of the previous 16, individual 15 minute, intervals. |
| OCT uas7616IntervalStat | 1.3.6.1.4.1.498.12.4.9.1.3 | OCTET STRING | read-only | Returns a bitwise map of the interface in one of the previous 16, individual 15 minute, intervals. Octet 1 bit 7 - not used bit 6 - future use bit 5 - future use bit 4 - future use bit 3 - future use bit 2 - future use bit 1 - 2^1 bit 0 - 2^0 Loop ID Octet 2 bit 7 - not used bit 6 - future use bit 5 - future use bit 4 - future use bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Interval Octet 3 bit 7 - not used bit 6 - future use bit 5 - future use bit 4 - future use bit 3 - future use bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 4 bit 7 - not used bit 6 - 2^6 bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Errored Seconds Octet 5 bit 7 - not used bit 6 - future use bit 5 - future use bit 4 - future use bit 3 - future use bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 6 bit 7 - not used bit 6 - 2^6 bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Severely Errored Seconds Octet 7 bit 7 - not used bit 6 - future use bit 5 - future use bit 4 - future use bit 3 - future use bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 8 bit 7 - not used bit 6 - 2^6 bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Unavailable Seconds Octet 9 bit 7 - not used bit 6 - future use bit 5 - future use bit 4 - future use bit 3 - future use bit 2 - 2^16 bit 1 - 2^15 bit 0 - 2^14 Octet 10 bit 7 - not used bit 6 - 2^13 bit 5 - 2^12 bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 11 bit 7 - not used bit 6 - 2^6 bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 FEBE (Far End Block Error Count) (not available on network element type 30) |
| uas7616IntervalTable | 1.3.6.1.4.1.498.12.4.9 | not-accessible | The 7616 Interval table. | |
| OCT uas7616LEDStatus | 1.3.6.1.4.1.498.12.4.5.1.4 | OCTET STRING | read-only | The GDC 7616 front panel LED Status. A value of 1 means on, 0 is off. byte 1 bit 7 (1.7) - not used 1.6 - not used 1.5 - loop 1 channel A (00 = No Change 01 = Green Active) 1.4 - (10 = Red Solid 11 = RedFlashing ) 1.3 - loop 1 channel B (00 = No Change 01 = Green Active) 1.2 - (10 = Red Solid 11 = RedFlashing ) 1.1 - loop 2 channel A (00 = No Change 01 = Green Active) 1.0 - (10 = Red Solid 11 = RedFlashing ) 2.7 - not used 2.6 - not used 2.5 - loop 2 channel B (00 = No Change 01 = Green Active) 2.4 - (10 = Red Solid 11 = RedFlashing ) 2.3 - loop 3 channel A (00 = No Change 01 = Green Active) 2.2 - (10 = Red Solid 11 = RedFlashing ) 2.1 - loop 3 channel B (00 = No Change 01 = Green Active) 2.0 - (10 = Red Solid 11 = RedFlashing ) 3.7 - not used 3.6 - not used 3.5 - not used 3.4 - alarm led 3.3 - test mode led 3.2 - in service 3.1 - system timing source 3.0 - management response |
| uas7616LocalAlarmConfigEntry | 1.3.6.1.4.1.498.12.4.14.1 | not-accessible | An entry in the GDC Local Alarm Configuration table. | |
| SCI uas7616LocalAlarmConfigIndex | 1.3.6.1.4.1.498.12.4.14.1.1 | SCinstance | read-only | The index value which uniquely identifies the interface to which this entry is applicable. |
| uas7616LocalAlarmConfigTable | 1.3.6.1.4.1.498.12.4.14 | not-accessible | The 7616LocalAlarmConfigTable contains entries that configure alarm reporting. | |
| INT uas7616LocalES | 1.3.6.1.4.1.498.12.4.14.1.5 | INTEGER | read-write | Disables or enables the ES alarm on the Major buss or Minor buss. |
| INT uas7616LocalLossOfClock | 1.3.6.1.4.1.498.12.4.14.1.2 | INTEGER | read-write | Disables or enables the Loss of Clock alarm on the Major buss or Minor buss. |
| INT uas7616LocalNoSealingCurrent | 1.3.6.1.4.1.498.12.4.14.1.7 | INTEGER | read-write | Disables or enables the No Sealing Current alarm on the Major buss or Minor buss. |
| INT uas7616LocalOutOfSync | 1.3.6.1.4.1.498.12.4.14.1.6 | INTEGER | read-write | Disables or enables the Out of Sync alarm on the Major buss or Minor buss. |
| INT uas7616LocalSES | 1.3.6.1.4.1.498.12.4.14.1.4 | INTEGER | read-write | Disables or enables the SES alarm on the Major buss or Minor buss. |
| INT uas7616LocalUAS | 1.3.6.1.4.1.498.12.4.14.1.3 | INTEGER | read-write | Disables or enables the UAS alarm on the Major buss or Minor buss. |
| uas7616LossOfClockAlm | 1.3.6.1.4.1.498.12.13.1.4 | |||
| uas7616LpErroredSecondAlm | 1.3.6.1.4.1.498.12.13.1.9 | |||
| INT uas7616LPMajor | 1.3.6.1.4.1.498.12.4.14.1.8 | INTEGER | read-write | Disables or enables the Major alarm on the Major buss or Minor buss. |
| INT uas7616LPMinor | 1.3.6.1.4.1.498.12.4.14.1.9 | INTEGER | read-write | Disables or enables the Minor alarm on the Minor buss or Minor buss. |
| uas7616LpOutofSyncAlm | 1.3.6.1.4.1.498.12.13.1.5 | |||
| uas7616LpSealingCurrentNoContinuityAlm | 1.3.6.1.4.1.498.12.13.1.6 | |||
| uas7616LpSeverelyErroredSecondAlm | 1.3.6.1.4.1.498.12.13.1.8 | |||
| uas7616LpUnavailableSecondAlm | 1.3.6.1.4.1.498.12.13.1.7 | |||
| uas7616mAlarm | 1.3.6.1.4.1.498.12.14 | |||
| uas7616mAlarmConfigEntry | 1.3.6.1.4.1.498.12.14.2.1 | not-accessible | An entry in the GDC Alarm Configuration table. | |
| OID uas7616mAlarmConfigIdentifier | 1.3.6.1.4.1.498.12.14.2.1.2 | OBJECT IDENTIFIER | read-only | The unique alarm identifier assigned to this alarm type. The format of this identifier is an OBJECT IDENTIFIER that has the following format: {iso(1) org(3) dod(6) internet(1) private(4) enterprises(1) gdc(498) xxx(x) alarm(z) yyy(y) where xxx(x) is the administratively assigned family object identifier (z) is the object identifier for alarms in the family defined MIB and yyy(y) is the administratively assigned alarm type identifier for this alarm. |
| SCI uas7616mAlarmConfigIndex | 1.3.6.1.4.1.498.12.14.2.1.1 | SCinstance | read-only | The index value which uniquely identifies the interface to which this entry is applicable. |
| uas7616mAlarmConfigTable | 1.3.6.1.4.1.498.12.14.2 | not-accessible | The uas7616mAlarmConfigTable contains entries that configure alarm reporting. The structure of the table is such that alarm configuration is supported on a unit and interface basis, and then on an alarm type basis within the interface. For simplicity sake alarms, be they unit or interface related, are represented in one table. | |
| INT uas7616mAlarmCountThreshold | 1.3.6.1.4.1.498.12.14.2.1.3 | INTEGER | read-write | This function sets/reads the Major or Minor BER alarm threshold criteria. |
| uas7616mAlarmData | 1.3.6.1.4.1.498.12.14.1 | |||
| uas7616mDiagRxErrAlm | 1.3.6.1.4.1.498.12.14.1.2 | |||
| STR uas7616MIBVersion | 1.3.6.1.4.1.498.12.4.1 | DisplayString | read-only | The version number of the MIB, to allow products to know which MIB is being supported. The version number will be x.yzT where x is a major revision (1-9), y is a minor revision(0-9), z is a typo revision (0-9) and T indicates the MIB is still a test revision(A-Z). When a release is complete no T should exist. |
| uas7616mLossOfClockAlm | 1.3.6.1.4.1.498.12.14.1.4 | |||
| uas7616mLpErroredSecondAlm | 1.3.6.1.4.1.498.12.14.1.8 | |||
| uas7616mLPMajorAlm | 1.3.6.1.4.1.498.12.14.1.9 | |||
| uas7616mLPMinorAlm | 1.3.6.1.4.1.498.12.14.1.10 | |||
| uas7616mLpOutofSyncAlm | 1.3.6.1.4.1.498.12.14.1.5 | |||
| uas7616mLpSealingCurrentNoContinuityAlm | 1.3.6.1.4.1.498.12.14.1.6 | |||
| uas7616mLpUnavailableSecondAlm | 1.3.6.1.4.1.498.12.14.1.7 | |||
| uas7616mNoResponseAlm | 1.3.6.1.4.1.498.12.14.1.1 | |||
| INT uas7616ModuleClkSrc | 1.3.6.1.4.1.498.12.4.5.1.10 | INTEGER | read-write | This variable is used to read or set the Module Clock Source. This variable must be system when uas7616SysTimingGen is set to none. Any of the three selections when uas7616SysTimingGen is set to secondary, and internal or recovered when uas7616SysTimingGen is set to primary. |
| uas7616mPowerUpAlm | 1.3.6.1.4.1.498.12.14.1.3 | |||
| uas7616NoResponseAlm | 1.3.6.1.4.1.498.12.13.1.1 | |||
| INT uas7616NumberofValidIntervals | 1.3.6.1.4.1.498.12.4.13.1.2 | INTEGER | read-only | This variable is used to read the number of intervals collected. Each interval is an increment of 15 minutes. |
| uas7616PowerUpAlm | 1.3.6.1.4.1.498.12.13.1.3 | |||
| uas7616Recent24HrEntry | 1.3.6.1.4.1.498.12.4.11.1 | not-accessible | An entry in the Recent24Hr table. | |
| SCI uas7616Recent24HrIndex | 1.3.6.1.4.1.498.12.4.11.1.1 | SCinstance | read-only | The index value which uniquely identifies the interface to which this entry is applicable. This has the form of a SCinstance which defines the slot, line, drop, and interface. |
| OCT uas7616Recent24HrStat | 1.3.6.1.4.1.498.12.4.11.1.2 | OCTET STRING | read-only | Returns a bitwise snapshot of the interval statistics. Octet 1 bit 7 - not used bit 6 - future use bit 5 - future use bit 4 - future use bit 3 - future use bit 2 - future use bit 1 - 2^1 bit 0 - 2^0 Loop ID Octet 2 bit 7 - not used bit 6 - future use bit 5 - future use bit 4 - future use bit 3 - future use bit 2 - >65535 bit 1 - 2^15 bit 0 - 2^14 Octet 3 bit 7 - not used bit 6 - 2^13 bit 5 - 2^12 bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 4 bit 7 - not used bit 6 - 2^6 bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Errored Seconds Octet 5 bit 7 - not used bit 6 - future use bit 5 - future use bit 4 - future use bit 3 - future use bit 2 - >65535 bit 1 - 2^15 bit 0 - 2^14 Octet 6 bit 7 - not used bit 6 - 2^13 bit 5 - 2^12 bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 7 bit 7 - not used bit 6 - 2^6 bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Severely Errored Seconds Octet 8 bit 7 - not used bit 6 - future use bit 5 - future use bit 4 - future use bit 3 - future use bit 2 - >65535 bit 1 - 2^15 bit 0 - 2^14 Octet 9 bit 7 - not used bit 6 - 2^13 bit 5 - 2^12 bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 10 bit 7 - not used bit 6 - 2^6 bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Unavailable Seconds Octet 11 bit 7 - not used bit 6 - future use bit 5 - future use bit 4 - future use bit 3 - future use bit 2 - 2^23 bit 1 - 2^22 bit 0 - 2^21 Octet 12 bit 7 - not used bit 6 - 2^20 bit 5 - 2^19 bit 4 - 2^18 bit 3 - 2^17 bit 2 - 2^16 bit 1 - 2^15 bit 0 - 2^14 Octet 13 bit 7 - not used bit 6 - 2^13 bit 5 - 2^12 bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 14 bit 7 - not used bit 6 - 2^6 bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 FEBE (Far End Block Error Count) (not available on network element type 30) |
| uas7616Recent24HrTable | 1.3.6.1.4.1.498.12.4.11 | not-accessible | The Recent24Hr table. 4 hour interval. | |
| INT uas7616ResetIntervals | 1.3.6.1.4.1.498.12.4.5.1.7 | INTEGER | read-write | This variable is used to reset Loop performance intervals. When it is set to reset, the Loop performance tables are reset to zero. |
| INT uas7616ResetMajorAlarm | 1.3.6.1.4.1.498.12.4.5.1.11 | INTEGER | read-write | This variable is used to reset alarm per Loop basis. |
| INT uas7616ResetMinorAlarm | 1.3.6.1.4.1.498.12.4.5.1.12 | INTEGER | read-write | This variable is used to reset alarm per Loop basis. |
| INT uas7616SetRealTime | 1.3.6.1.4.1.498.12.4.5.1.9 | INTEGER | read-write | Number of seconds from midnight Dec 31, 1969. |
| INT uas7616SoftReset | 1.3.6.1.4.1.498.12.4.5.1.2 | INTEGER | read-write | Forces a soft reset on the network element. The reset selection is write only. The normal selection is read only. |
| INT uas7616SystemTimingGenStatus | 1.3.6.1.4.1.498.12.4.2.1.4 | INTEGER | read-only | Indicates if the units configured for primary or secondary system clock are actually supplying clock and if it is the 8hkz, 4mhz, or both. |
| INT uas7616SysTimingGen | 1.3.6.1.4.1.498.12.4.5.1.6 | INTEGER | read-write | Selects if the unit provides system timing. none(1) - does not provide Timing Generator primary(2) - unit is primary Timing Generator for the shelf. secondary(3) - unit is secondary Timig Generator for the shelf. Only 1 unit in the shelf can the primary or secondary timing generator. All other must be none. |
| INT uas7616SysUpTime | 1.3.6.1.4.1.498.12.4.5.1.8 | INTEGER | read-only | This variable is used to report the elapsed system tick time for conversion to real time at the controller and is not related to the sysUpTime referenced in MIB-II. Upon power-up of the unit, the elapsed time is cleared. The elapsed time counter rolls over upon reaching the maximum count. |
| INT uas7616TerminationType | 1.3.6.1.4.1.498.12.4.3.1.3 | INTEGER | read-write | Object to select the Termination Type for the 7616. |
| INT uas7616TimeSlot | 1.3.6.1.4.1.498.12.4.15.1.4 | INTEGER | read-write | Defines the time slot of the highway the channel of the loop is assigned to. Valid range is 1 to 31. A value of 64 indicates the channel is not assigned to a highway. |
| uas7616TSAssignEntry | 1.3.6.1.4.1.498.12.4.15.1 | not-accessible | An entry in the GDC Circuit Identification table. | |
| SCI uas7616TSAssignIndex | 1.3.6.1.4.1.498.12.4.15.1.1 | SCinstance | read-only | The index value which uniquely identifies the interface to which this entry is applicable. |
| uas7616TSAssignTable | 1.3.6.1.4.1.498.12.4.15 | not-accessible | The 7616TSAssignTable contains entries that provide a means to assign a highway and time slot of that highway to the channel of a loop. | |
| STR uas7616TSCircuitID | 1.3.6.1.4.1.498.12.4.15.1.5 | DisplayString | read-write | Name to identify the circuit for the channel of this loop. |
| INT uas7616TXClockSource | 1.3.6.1.4.1.498.12.4.3.1.2 | INTEGER | read-write | Object to select the Transmit Clock Source for the 7616. |
| uas7616UnavailableTimeRegEntry | 1.3.6.1.4.1.498.12.4.12.1 | not-accessible | An entry in the Unavailable Time Register table. | |
| SCI uas7616UnavailableTimeRegIndex | 1.3.6.1.4.1.498.12.4.12.1.1 | SCinstance | read-only | The index value which uniquely identifies the interface to which this entry is applicable. This has the form of a SCinstance which defines the slot, line, drop, and interface. |
| INT uas7616UnavailableTimeRegNumber | 1.3.6.1.4.1.498.12.4.12.1.2 | INTEGER | read-only | A number between 1 and 6, where the number is the number of the Unavailable Time Register. |
| INT uas7616UnavailableTimeRegStart | 1.3.6.1.4.1.498.12.4.12.1.3 | INTEGER | read-only | Start time of one of the Unavailable Time Registers. |
| INT uas7616UnavailableTimeRegStop | 1.3.6.1.4.1.498.12.4.12.1.4 | INTEGER | read-only | Stop time of one of the Unavailable Time Registers. |
| uas7616UnavailableTimeRegTable | 1.3.6.1.4.1.498.12.4.12 | not-accessible | The 7616 Unavailable Time Register table. | |
| uas7616WhatAreYouEntry | 1.3.6.1.4.1.498.12.4.2.1 | not-accessible | An entry in the GDC 7616 What Are You table. | |
| SCI uas7616WhatAreYouIndex | 1.3.6.1.4.1.498.12.4.2.1.1 | SCinstance | read-only | This object is the identifier of the 7616 What Are You table. |
| uas7616WhatAreYouTable | 1.3.6.1.4.1.498.12.4.2 | not-accessible | The GDC 7616 What Are You Table. |
RFC description
GDC UAS 7616 HDSL/2B1Q network interface MIB for T1/E1 circuit alarm, performance statistics, and loop management.
Start monitoring General DataComm (GDC) UAS 7616 multiplexer/access chassis with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.