DKSF-60-4-X-X-X

All MIBs › DKSF-60-4-X-X-X

Organization: NetPing East, Alentis Electronics

Last Updated: 2014-11-21

Category: Domain: Environmental Monitoring, Domain: Power Management, Vendor: NetPing/DKSF

Description: MIB for DKSF-60 NetPing device firmware 4.x providing remote power and environmental monitoring management.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is DKSF-60-4-X-X-X?

DKSF-60-4-X-X-X is the vendor MIB for the NetPing DKSF-60 device (firmware 4.x), a network-attached remote power and environmental monitoring/control unit in the NetPing product line. It exposes relay control objects and power channel status objects used to manage and monitor connected equipment power state. Because the device itself is an embedded sensor/relay controller, its monitoring value lies almost entirely in hardware status: whether relays are engaged, whether power channels are live, and reset actions taken on them, rather than general CPU/memory metrics. It is a self-contained proprietary MIB with no apparent dependency on other standard MIBs beyond basic SNMP trap infrastructure. It is typically deployed in data closets or remote sites to allow administrators to remotely power-cycle stuck equipment and monitor power presence. Engineers can download the DKSF-60-4-X-X-X file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in DKSF-60-4-X-X-X. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

NetPing DKSF-60 remote power/relay control unit

Monitoring Examples

An administrator would poll npRelayTable (npRelayEntry, npRelayN) for npRelayState and npRelayMode to determine whether a relay channel is on or off, and could use npRelayFlip or npRelayStartReset to remotely toggle or reset a hung device connected to that channel. The npPwrTable (npPwrEntry, npPwrChannelN) with npPwrStartReset lets an administrator confirm power channel status and trigger a power-channel reset if a channel reports a fault. npRelayMemo provides a descriptive label identifying what equipment each relay controls.

What Can Be Monitored

relay on/off state per channel
power channel status
relay and power channel reset actions
relay channel labels/memo

Imported Objects

From SNMPv2-MIB

snmpTraps

OBJECT-IDENTITY

From SNMPv2-SMI

Counter32
Counter64
Gauge32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
TimeTicks
enterprises

From SNMPv2-TC

DisplayString
TEXTUAL-CONVENTION
TimeStamp
TruthValue

How to Use in IPNetwork Monitor

Example using npIoPulseCounter OID:

Select a NetPing DKSF-60 remote power/relay control unit as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type npIoPulseCounter into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. It reports the pulse Counter on IO input line (counts positive fronts) Write 0 to reset. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
lightcom	1.3.6.1.4.1.25728
netPing	1.3.6.1.4.1.25728.50			Generic MIB for NetPing remote sensing and control
npCurLoop	1.3.6.1.4.1.25728.8300
npCurLoopEntry	1.3.6.1.4.1.25728.8300.1.1		not-accessible	Current loop sensors Table Row
INT npCurLoopI	1.3.6.1.4.1.25728.8300.1.1.3	INTEGER	read-only	Loop current, mA
INT npCurLoopN	1.3.6.1.4.1.25728.8300.1.1.1	INTEGER	read-only	Index of current loop, 1 to max supported
INT npCurLoopPower	1.3.6.1.4.1.25728.8300.1.1.7	INTEGER	read-write	Control of loop power 0=Off, 1=On, 2=reset by off/on power
INT npCurLoopR	1.3.6.1.4.1.25728.8300.1.1.5	INTEGER	read-only	Resistance of the loop, Ohm
INT npCurLoopStatus	1.3.6.1.4.1.25728.8300.1.1.2	INTEGER	read-only	Status of the loop 0=Normal, 1=Alert, 2=Cut, 3=Short, 4=Not Powered
npCurLoopTable	1.3.6.1.4.1.25728.8300.1		not-accessible	Current loop sensors Table
NTF npCurLoopTrap	1.3.6.1.4.1.25728.8300.2.0.1			Status of current loop N has changed!
INT npCurLoopTrapI	1.3.6.1.4.1.25728.8300.2.3	INTEGER	read-only	Loop current, mA
INT npCurLoopTrapN	1.3.6.1.4.1.25728.8300.2.1	INTEGER	read-only	Index of current loop, which status has changed
INT npCurLoopTrapPower	1.3.6.1.4.1.25728.8300.2.7	INTEGER	read-write	Status of loop power 0=Off, 1=On
npCurLoopTrapPrefix	1.3.6.1.4.1.25728.8300.2.0
INT npCurLoopTrapR	1.3.6.1.4.1.25728.8300.2.5	INTEGER	read-only	Resistance of the loop, Ohm
npCurLoopTraps	1.3.6.1.4.1.25728.8300.2
INT npCurLoopTrapStatus	1.3.6.1.4.1.25728.8300.2.2	INTEGER	read-only	Status of the loop 0=Normal, 1=Alert, 2=Cut, 3=Short, 4=Not Powered
INT npCurLoopTrapV	1.3.6.1.4.1.25728.8300.2.4	INTEGER	read-only	Voltage drop on the loop, mV
INT npCurLoopV	1.3.6.1.4.1.25728.8300.1.1.4	INTEGER	read-only	Voltage drop on the loop, mV
INT npForcedReboot	1.3.6.1.4.1.25728.911.3	INTEGER	read-write	Write 1 to immediate forced reboot
npIo	1.3.6.1.4.1.25728.8900
npIoEntry	1.3.6.1.4.1.25728.8900.1.1		not-accessible	Digital Input/output Table Row
INT npIoLevelIn	1.3.6.1.4.1.25728.8900.1.1.2	INTEGER	read-only	Input level, 0 or 1
INT npIoLevelOut	1.3.6.1.4.1.25728.8900.1.1.3	INTEGER	read-write	Output level, 0 or 1. Write -1 to flip output.
INT npIoLineN	1.3.6.1.4.1.25728.8900.1.1.1	INTEGER	read-only	Number of IO line, from 1 to max supported
STR npIoMemo	1.3.6.1.4.1.25728.8900.1.1.6	DisplayString	read-only	IO line memo
C32 npIoPulseCounterEx	1.3.6.1.4.1.25728.8900.1.1.9	Counter32	read-write	Pulse Counter on IO input line (counts positive fronts) Write 0 to reset.
INT npIoSinglePulseDuration	1.3.6.1.4.1.25728.8900.1.1.12	INTEGER	read-write	Set duration of single pulse on IO output line, 100ms to 25500ms, min. step is 100ms
INT npIoSinglePulseStart	1.3.6.1.4.1.25728.8900.1.1.13	INTEGER	read-write	Write 1 to start single pulse on IO output. Output will be inverted for time, specified by npIoSinglePulseDuration
npIoTable	1.3.6.1.4.1.25728.8900.1		not-accessible	Digital Input/output Table
NTF npIoTrap	1.3.6.1.4.1.25728.8900.2.0.1			Input state of IO line is changed
INT npIoTrapLevelIn	1.3.6.1.4.1.25728.8900.2.2	INTEGER	read-only	Trap data, new Input level, 0 or 1
INT npIoTrapLineN	1.3.6.1.4.1.25728.8900.2.1	INTEGER	read-only	Trap data, Number of IO line
STR npIoTrapMemo	1.3.6.1.4.1.25728.8900.2.6	DisplayString	read-only	Trap data, IO line memo
npIoTrapPrefix	1.3.6.1.4.1.25728.8900.2.0
npIoTraps	1.3.6.1.4.1.25728.8900.2
npIr	1.3.6.1.4.1.25728.7900
npIrCtrl	1.3.6.1.4.1.25728.7900.1
INT npIrPlayCmd	1.3.6.1.4.1.25728.7900.1.1	INTEGER	read-write	Write IR command number to send IR command
INT npIrReset	1.3.6.1.4.1.25728.7900.1.2	INTEGER	read-write	Write 1 to reset IR transiever. After reset, send IR command and check npIrStatus.
INT npIrStatus	1.3.6.1.4.1.25728.7900.1.3	INTEGER	read-only	IR transiever status
npPwr	1.3.6.1.4.1.25728.5800
INT npPwrChannelN	1.3.6.1.4.1.25728.5800.3.1.1	INTEGER	read-only	The id of watchdog/power channel
npPwrEntry	1.3.6.1.4.1.25728.5800.3.1		not-accessible	Watchdog and outlet/relay control table row
INT npPwrManualMode	1.3.6.1.4.1.25728.5800.3.1.3	INTEGER	read-write	Mode of power channel 0 - manual off 1 - manual on 2 - watchdog 3 - schedule 4 - schedule and watchdog 5 - controlled by Logic
STR npPwrMemo	1.3.6.1.4.1.25728.5800.3.1.6	DisplayString	read-only	Relay channel memo
INT npPwrRelayFlip	1.3.6.1.4.1.25728.5800.3.1.14	INTEGER	read-write	Write -1 to flip between manual on and manual off states of relay
INT npPwrRelayState	1.3.6.1.4.1.25728.5800.3.1.15	INTEGER	read-only	Actual relay state at the moment, regardless of source of control. 0 - relay is off 1 - relay is on
INT npPwrRepeatingResetsCounter	1.3.6.1.4.1.25728.5800.3.1.5	INTEGER	read-only	Counter of continous failed watchdog resets
INT npPwrResetsCounter	1.3.6.1.4.1.25728.5800.3.1.4	INTEGER	read-write	Counter of watchdog resets Write 0 to clear.
INT npPwrStartReset	1.3.6.1.4.1.25728.5800.3.1.2	INTEGER	read-write	Write 1 to start forced reset On read: 0 - normal operation 1 - reset is active 2 - reboot pause is active or watchdog is inactive
npPwrTable	1.3.6.1.4.1.25728.5800.3		not-accessible	Watchdog and outlet/relay control table
npReboot	1.3.6.1.4.1.25728.911
npRelay	1.3.6.1.4.1.25728.5500
npRelayEntry	1.3.6.1.4.1.25728.5500.5.1		not-accessible	Relay/outlet table row
INT npRelayFlip	1.3.6.1.4.1.25728.5500.5.1.14	INTEGER	read-write	Write -1 to flip between manual on and manual off states of relay
STR npRelayMemo	1.3.6.1.4.1.25728.5500.5.1.6	DisplayString	read-only	Relay memo
INT npRelayMode	1.3.6.1.4.1.25728.5500.5.1.2	INTEGER	read-write	Control of relay: 0 - manual off 1 - manual on 2 - watchdog 3 - schedule 4 - both schedule and watchdog (while switched on by schedule) 5 - logic
INT npRelayN	1.3.6.1.4.1.25728.5500.5.1.1	INTEGER	read-only	The N of output relay
INT npRelayStartReset	1.3.6.1.4.1.25728.5500.5.1.3	INTEGER	read-write	Write 1 to start reset (switch relay off for some time)
INT npRelayState	1.3.6.1.4.1.25728.5500.5.1.15	INTEGER	read-only	Actual relay state at the moment, regardless of source of control. 0 - relay is off 1 - relay is on
npRelayTable	1.3.6.1.4.1.25728.5500.5		not-accessible	Watchdog and outlet/relay control table
npRelHumidity	1.3.6.1.4.1.25728.8400
INT npRelHumSafeRangeHigh	1.3.6.1.4.1.25728.8400.2.7	INTEGER	read-only	Relative Humidity safe range, top margin, %RH
INT npRelHumSafeRangeLow	1.3.6.1.4.1.25728.8400.2.8	INTEGER	read-only	Relative Humidity safe range, bottom margin, %RH
npRelHumSensor	1.3.6.1.4.1.25728.8400.2
INT npRelHumSensorStatus	1.3.6.1.4.1.25728.8400.2.3	INTEGER	read-only	Status of the Rel.Humidity Sensor One 0=Normal, 1=Error or Sensor isn't connected
INT npRelHumSensorStatusH	1.3.6.1.4.1.25728.8400.2.5	INTEGER	read-only	Status of Relative Humiduty
INT npRelHumSensorValueH	1.3.6.1.4.1.25728.8400.2.2	INTEGER	read-only	Relative humidity value, %
INT npRelHumSensorValueT	1.3.6.1.4.1.25728.8400.2.4	INTEGER	read-only	Sensor temperature, deg.C
I32 npRelHumSensorValueT100	1.3.6.1.4.1.25728.8400.2.9	Integer32	read-only	Sensor temperature, deg.C * 100 (fixed point two decimal places) Used to get access to the fractional part of T value
INT npResetStack	1.3.6.1.4.1.25728.911.2	INTEGER	read-write	Write 1 to re-initialize network stack
INT npSoftReboot	1.3.6.1.4.1.25728.911.1	INTEGER	read-write	Write 1 to reboot device after current operations completition
npThermo	1.3.6.1.4.1.25728.8800
npThermoEntry	1.3.6.1.4.1.25728.8800.1.1		not-accessible	Thermo Sensors Table Row
INT npThermoHigh	1.3.6.1.4.1.25728.8800.1.1.5	INTEGER	read-only	Top margin of normal temperature range, deg.C
INT npThermoLow	1.3.6.1.4.1.25728.8800.1.1.4	INTEGER	read-only	Bottom margin of normal temperature range, deg.C
STR npThermoMemo	1.3.6.1.4.1.25728.8800.1.1.6	DisplayString	read-only	T channel memo
INT npThermoSensorN	1.3.6.1.4.1.25728.8800.1.1.1	INTEGER	read-only	The id of temperature sensor, 1 to 8
INT npThermoStatus	1.3.6.1.4.1.25728.8800.1.1.3	INTEGER	read-only	Temperature status (0=fault, 1=underheat, 2=normal, 3=overheat)
npThermoTable	1.3.6.1.4.1.25728.8800.1		not-accessible	Thermo Sensors Table
NTF npThermoTrap	1.3.6.1.4.1.25728.8800.2.0.1			Status of Thermo sensor is changed (crossing of normal temp. range)
INT npThermoTrapHigh	1.3.6.1.4.1.25728.8800.2.5	INTEGER	read-only	Top margin of normal temperature range, deg.C
INT npThermoTrapLow	1.3.6.1.4.1.25728.8800.2.4	INTEGER	read-only	Bottom margin of normal temperature range, deg.C
STR npThermoTrapMemo	1.3.6.1.4.1.25728.8800.2.6	DisplayString	read-only	T channel memo
npThermoTrapPrefix	1.3.6.1.4.1.25728.8800.2.0
npThermoTraps	1.3.6.1.4.1.25728.8800.2
INT npThermoTrapSensorN	1.3.6.1.4.1.25728.8800.2.1	INTEGER	read-only	The id of temperature sensor, 1 to 8
INT npThermoTrapStatus	1.3.6.1.4.1.25728.8800.2.3	INTEGER	read-only	Temperature status (0=fault, 1=underheat, 2=normal, 3=overheat)
INT npThermoTrapValue	1.3.6.1.4.1.25728.8800.2.2	INTEGER	read-only	Temperature, deg.C
INT npThermoValue	1.3.6.1.4.1.25728.8800.1.1.2	INTEGER	read-only	Temperature, deg.C

RFC description

Generic MIB for NetPing remote sensing and control devices, monitoring relays, I/O ports, and temperature sensors.

Start monitoring NetPing DKSF-60 remote power/relay control unit with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download DKSF-60-4-X-X-X