CAT2600-MIB

All MIBs › CAT2600-MIB

Category: Vendor: Cabletron/Enterasys

Description: Manages Cabletron CAT2600 switching hub port configuration, traffic statistics, and operational status.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is CAT2600-MIB?

CAT2600-MIB is a Cabletron Systems enterprise MIB for the CAT2600 switching hub, an older Token Ring/switching product, that manages port configuration, traffic statistics, and operational status. Based on the available data it covers Token Ring-specific port attributes, including a port's beacon station address and Next Active Upstream Neighbor (NAUN), both used to pinpoint Token Ring beaconing faults, along with the broader port configuration and traffic-statistics scope implied by its description. Its monitoring emphasis is on port-level hardware/link status and traffic performance, letting an operator locate exactly where on the ring a beaconing fault originates and confirm that port traffic and status are otherwise healthy. It is a Cabletron-proprietary schema with no evident dependency on external standard MIBs beyond typical Token Ring conventions. It is deployed on legacy Cabletron CAT2600 switching hubs in Token Ring network environments, where CAT2600-MIB SNMP monitoring remains useful for isolating beaconing faults to a specific port.

IPNetwork Monitor allows you to monitor SNMP objects defined in CAT2600-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Cisco Catalyst 2600 switching hub (legacy)

Monitoring Examples

An operator diagnosing a Token Ring fault would check cat2600TsPortBeaconStationAddress and cat2600TsPortBeaconNAUN on the affected port to identify the beaconing station and its nearest active upstream neighbor, pinpointing the fault to a specific cable segment or adapter. Persistent beacon addresses reported over successive polls would confirm an ongoing hardware or cabling fault rather than a transient ring reconfiguration.

What Can Be Monitored

beacon station address per port
Next Active Upstream Neighbor (NAUN) per port
port configuration/traffic statistics

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter
IpAddress
TimeTicks
enterprises

From RFC1213-MIB

DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
cat2600	1.3.6.1.4.1.9.1.111
cat2600Ts	1.3.6.1.4.1.9.1.111.1
INT cat2600TsAddrAgingTime	1.3.6.1.4.1.9.1.111.1.2.1.2.7	INTEGER	read-write	Number of minutes of inactivity before an address entity is aged out. A value of zero means no aging. Note: if an address shows up on another port, the original port to address assignment is automatically deleted. The value is saved across resets and power cycles. The default value for this object is 5 minutes.
cat2600TsConfig	1.3.6.1.4.1.9.1.111.1.2.1.1
INT cat2600TsCrcThresholdHi	1.3.6.1.4.1.9.1.111.1.2.1.1.22	INTEGER	read-write	Threshold for the switch to change to store and forward mode. A change in mode also generates a trap.
INT cat2600TsCrcThresholdLow	1.3.6.1.4.1.9.1.111.1.2.1.1.23	INTEGER	read-write	Threshold for the switch to change to store and forward mode. A change in mode also generates a trap.
IP cat2600TsDefaultGateway	1.3.6.1.4.1.9.1.111.1.2.1.1.10	IpAddress	read-write	IP default gateway used by the switch. Changes to this object take effect immediately.
MAC cat2600TsDmnBaseBridgeAddr	1.3.6.1.4.1.9.1.111.1.2.3.1.1.10	MacAddr	read-only	Base MAC address of this domain. Internally equivalent to dtrCRFMacAddress and to ifPhysAddress of the 'Domain' port.
cat2600TsDmnEntry	1.3.6.1.4.1.9.1.111.1.2.3.1.1		not-accessible	Definition of each row in the domain Table
INT cat2600TsDmnIfIndex	1.3.6.1.4.1.9.1.111.1.2.3.1.1.9	INTEGER	read-only	The ifIndex of the interface entry corresponding to each configured domain.
INT cat2600TsDmnIndex	1.3.6.1.4.1.9.1.111.1.2.3.1.1.1	INTEGER	read-only	Domain number for each row.
IP cat2600TsDmnIpAddress	1.3.6.1.4.1.9.1.111.1.2.3.1.1.4	IpAddress	read-write	The IP Address of this Domain. Changes to this object will take effect immediately.
IP cat2600TsDmnIpDefaultGateway	1.3.6.1.4.1.9.1.111.1.2.3.1.1.6	IpAddress	read-write	The IP Address of the default gateway for this Domain. Changes to this object will take effect immediately.
INT cat2600TsDmnIpState	1.3.6.1.4.1.9.1.111.1.2.3.1.1.3	INTEGER	read-write	IP configuration method for this domain.
IP cat2600TsDmnIpSubnetMask	1.3.6.1.4.1.9.1.111.1.2.3.1.1.5	IpAddress	read-write	The subnet mask for this domain. Changes to this object will take effect immediately.
INT cat2600TsDmnMostStations	1.3.6.1.4.1.9.1.111.1.2.3.1.1.12	INTEGER	read-only	Highest aggregate number of stations ever active on all ports at one time, since the last reset or power cycle.
STR cat2600TsDmnName	1.3.6.1.4.1.9.1.111.1.2.3.1.1.8	DisplayString	read-write	User assigned name for each domain.
INT cat2600TsDmnNumStations	1.3.6.1.4.1.9.1.111.1.2.3.1.1.11	INTEGER	read-only	Aggregate number of currently active stations (nodes) on all ports in the domain.
OCT cat2600TsDmnPorts	1.3.6.1.4.1.9.1.111.1.2.3.1.1.2	OCTET STRING	read-write	The set of ports that belong to this Domain. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the TokenRing Switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'. Warning: You will not receive a set- complete message as a set to this object causes the ports to reset.
cat2600TsDmns	1.3.6.1.4.1.9.1.111.1.2.3
OCT cat2600TsDmnStationAddress	1.3.6.1.4.1.9.1.111.1.2.3.5.1.2	OCTET STRING	read-only	The Station's MAC address.
INT cat2600TsDmnStationDmnIndex	1.3.6.1.4.1.9.1.111.1.2.3.5.1.1	INTEGER	read-only	Integer reference to the domain number in the domain table.
cat2600TsDmnStationEntry	1.3.6.1.4.1.9.1.111.1.2.3.5.1		not-accessible	Definition of each row in the domain specific station table. The object is equivalent to dtrFdbDynamicAddrTable or dtrFdbStaticAddrTable depending if the entry is learned or is a configured filter.
INT cat2600TsDmnStationPort	1.3.6.1.4.1.9.1.111.1.2.3.5.1.3	INTEGER	read-only	The source port for the Station. The dtrConc MIB equivalents are dtrFdbDynamicAddrPortNumber and dtrFdbStaticAddrPortNumber.
cat2600TsDmnStationTable	1.3.6.1.4.1.9.1.111.1.2.3.5		not-accessible	Stations seen in each domain.
OCT cat2600TsDmnStationTraffic	1.3.6.1.4.1.9.1.111.1.2.3.5.1.4	OCTET STRING	read-only	A bit string that identifies the ports that this station has generated traffic to or from. The bits correspond to ports, with bits and ports numbered from right to left so that bit 0 represents the CPU, bit 1 represents port 1, and so forth. For example, the returned string 01 4D can be expanded to: 00000001 01001101 binary representation of object string xxxxxxx8 7654321C ports corresponding to bits This indicates ports 8, 6, 3, 2 and the CPU. The size of this string is adjusted to include all ports with traffic.
INT cat2600TsDmnStp	1.3.6.1.4.1.9.1.111.1.2.3.1.1.7	INTEGER	read-write	Turn Spanning tree on or off. Changes to this object will take effect immediately. The Spanning Tree Objects themselves are in the dtrConc MIB.
cat2600TsDmnTable	1.3.6.1.4.1.9.1.111.1.2.3.1		not-accessible	Currently active domains on the switch.
cat2600TsFilter	1.3.6.1.4.1.9.1.111.1.2.5
cat2600TsFilterEntry	1.3.6.1.4.1.9.1.111.1.2.5.1.1		not-accessible	Definition of each row in the filter table.
OCT cat2600TsFilterMask	1.3.6.1.4.1.9.1.111.1.2.5.1.1.5	OCTET STRING	read-write	The filter mask for this station. The semantics of the filter mask depend on the type of filter. For a source filter, the mask gives the ports that are allowed to receive frames from the filtered address. For a destination filter, the mask gives the ports that are forced to receive frames destined to the filtered address. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16 (if available), etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
OCT cat2600TsFilterPorts	1.3.6.1.4.1.9.1.111.1.2.5.1.1.4	OCTET STRING	read-write	The set of ports to which this filter is applied. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the TokenRing Switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'. All frames with destination address equal to the station address corresponding to this entry and entering from any of the specified ports will be dropped. Setting this object with a MIB instance corresponding to the dotted decimal MAC address and a filter type, with the set value equal to the mask of ports you want to filter will create an entry in the table. Ex. MIB instance: 16.0.90.3.0.36.1 SNMP set value: 7F 00 00 00 This would create a filter entry with the following characteristics: MAC Address: 10 00 5A 03 00 24 (canonical format) Filter Type: source-filter Filter Ports: 2 3 4 5 6 7 8
MAC cat2600TsFilterStationAddress	1.3.6.1.4.1.9.1.111.1.2.5.1.1.1	MacAddr	read-only	The MAC address in a frame to which this entry's filtering information applies.
INT cat2600TsFilterStatus	1.3.6.1.4.1.9.1.111.1.2.5.1.1.3	INTEGER	read-write	This object indicates the status of this entry. valid(1) - this entry is currently in use and will remain so after the next reset of the bridge. invalid(2) - writing this value to the object removes the corresponding entry.
cat2600TsFilterTable	1.3.6.1.4.1.9.1.111.1.2.5.1		not-accessible	Filters set up in the switch.
INT cat2600TsFilterType	1.3.6.1.4.1.9.1.111.1.2.5.1.1.2	INTEGER	read-only	There are two types of filters (i) source filters which act on the source address portion of a packet and (ii) destination filters which act on the destination address portion of a packet.
INT cat2600TsFwCRC	1.3.6.1.4.1.9.1.111.1.2.1.1.6	INTEGER	read-only	Firmware binary image CRC value.
STR cat2600TsFwManufacturer	1.3.6.1.4.1.9.1.111.1.2.1.1.7	DisplayString	read-only	Firmware manufacturer.
INT cat2600TsFwSize	1.3.6.1.4.1.9.1.111.1.2.1.1.5	INTEGER	read-only	Size in bytes of the binary firmware image.
STR cat2600TsFwVer	1.3.6.1.4.1.9.1.111.1.2.1.1.1	DisplayString	read-only	The firmware version in the form major.minor. For port microcode (SOLO) version information see the mgmt.mib-2.interfaces.ifTable.ifEntry.ifDescr object.
STR cat2600TsHwVer	1.3.6.1.4.1.9.1.111.1.2.1.1.2	DisplayString	read-only	The hardware version in the form major.minor.
STR cat2600TsInstallationDate	1.3.6.1.4.1.9.1.111.1.2.1.1.4	DisplayString	read-write	Firmware installation date. This date is initially set by the Network Management station. Each time the NV RAM is cleared through the console this date needs to be set by the management station. This should be in the format YYYY MM DD HH MM SS.
INT cat2600TsInstalledMemory	1.3.6.1.4.1.9.1.111.1.2.1.2.12	INTEGER	read-only	Total amount of CPU memory installed (in megabytes).
IP cat2600TsIpAddr	1.3.6.1.4.1.9.1.111.1.2.1.1.8	IpAddress	read-write	IP address of the switch. Changes to this object take effect immediately.
cat2600TsMain	1.3.6.1.4.1.9.1.111.1.2.1
INT cat2600TsMaxStations	1.3.6.1.4.1.9.1.111.1.2.1.2.4	INTEGER	read-only	Highest aggregate number of stations which the switch can support simultaneously.
INT cat2600TsMostStations	1.3.6.1.4.1.9.1.111.1.2.1.2.3	INTEGER	read-only	Highest aggregate number of stations ever active on all ports at one time, since the last reset or power cycle. This includes the default MAC address entries from each port.
IP cat2600TsNetMask	1.3.6.1.4.1.9.1.111.1.2.1.1.9	IpAddress	read-write	IP subnet mask of the switch. Changes to this object take effect immediately.
INT cat2600TsNumberUFC	1.3.6.1.4.1.9.1.111.1.2.1.1.27	INTEGER	read-only	The number of UFCs installed in the switch. A value of zero (or an SNMP error of NOSUCH) indicates there are NO UFCs installed in this switch. This value indicates the number of entries in the cat2600TsUFCTable.
INT cat2600TsNumPorts	1.3.6.1.4.1.9.1.111.1.2.1.2.1	INTEGER	read-only	The maximum number of physical ports on the switch. This value includes all base ports plus all ports on any UFC cards. It does not include internally defined Bridge Relay Function ports or the CPU 'interface'.
CTR cat2600TsNumResets	1.3.6.1.4.1.9.1.111.1.2.1.2.6	Counter	read-only	Number of soft resets the switch has executed since the last hard reset or power cycle. Soft resets are defined as writing softReset(3) to cat2600TsReset, pressing the front panel reset button, executing a soft reset from the console, or resets induced by the switch firmware.
INT cat2600TsNumStations	1.3.6.1.4.1.9.1.111.1.2.1.2.2	INTEGER	read-only	Aggregate number of currently active stations (nodes) on all ports on the switch.
cat2600TsObjectID	1.3.6.1.4.1.9.1.111.1.1
cat2600TsObjects	1.3.6.1.4.1.9.1.111.1.2
cat2600TsOptDmnStaEntry	1.3.6.1.4.1.9.1.111.1.2.3.6.1		not-accessible	Definition of the rows in the optimized domain station address table. Rows can not be created or deleted via SNMP requests.
INT cat2600TsOptDmnStaPos	1.3.6.1.4.1.9.1.111.1.2.3.6.1.1	INTEGER	read-only	Second index for items in the optimized port station address table.
cat2600TsOptDmnStaTable	1.3.6.1.4.1.9.1.111.1.2.3.6		not-accessible	A table of station addresses known at an individual port. This table is designed to reduce the number of SNMP GETNEXT requests. This is done by packing many values into an octet string. (The maximum size frame should be used to return the result.) The instance returned for a GETNEXT is the value that identifies the last 'row' in the octet string. When the table is completely retrieved with one or more GETNEXTs, duplicate entries may be present, and entries may be skipped if the table is changing while being retrieved.
OCT cat2600TsOptDmnStaVal	1.3.6.1.4.1.9.1.111.1.2.3.6.1.2	OCTET STRING	read-only	An OCTET STRING containing a multiple number of stations from the domain station address table. Each entry is encoded in the following format: Station MAC address - 6 octets Port of Entry - 1 octet Traffic Mask - 4 octets The traffic mask is encoded in its raw form as stored in the switch. Octet 1 Bit position 7 6 5 4 3 2 1 0 Port Number 31 30 29 28 27 26 25 24 Octet 2 Bit position 7 6 5 4 3 2 1 0 Port Number 23 22 21 20 19 18 17 16 Octet 3 Bit position 7 6 5 4 3 2 1 0 Port Number 15 14 13 12 11 10 9 8 Octet 4 Bit position 7 6 5 4 3 2 1 0 Port Number 7 6 5 4 3 2 1 CPU
cat2600TsOptPortStaEntry	1.3.6.1.4.1.9.1.111.1.2.2.2.1		not-accessible	Definition of the rows in the optimized port station address table. Rows can not be created or deleted via SNMP requests.
INT cat2600TsOptPortStaPos	1.3.6.1.4.1.9.1.111.1.2.2.2.1.1	INTEGER	read-only	Second index for items in the optimized port station address table.
cat2600TsOptPortStaTable	1.3.6.1.4.1.9.1.111.1.2.2.2		not-accessible	A table of station addresses known at an individual port. This table is designed to reduce the number of SNMP GETNEXT requests. This is done by packing many values into an octet string. (The maximum size frame should be used to return the result.) The instance returned for a GETNEXT is the value that identifies the last 'row' in the octet string. When the table is completely retrieved with one or more GETNEXTs, duplicate entries may be present, and entries may be skipped if the table is changing while being retrieved.
OCT cat2600TsOptPortStaVal	1.3.6.1.4.1.9.1.111.1.2.2.2.1.2	OCTET STRING	read-only	An OCTET STRING containing a multiple number of stations from a port station address table. Each entry is encoded in the following format: Station MAC address - 6 octets Location 1 - local 2 - remote - 1 octet Port of exit Mask - 4 octets Source Frame Count - 4 octets (integer in little endian) Destn Frame Count - 4 octets (integer in little endian) Source Byte Count - 4 octets (integer in little endian) Destn Byte Count - 4 octets (integer in little endian) The Port of exit mask is encoded in its raw form as stored in the switch. Octet 1 Bit position 7 6 5 4 3 2 1 0 Port Number 31 30 29 28 27 26 25 24 Octet 2 Bit position 7 6 5 4 3 2 1 0 Port Number 23 22 21 20 19 18 17 16 Octet 3 Bit position 7 6 5 4 3 2 1 0 Port Number 15 14 13 12 11 10 9 8 Octet 4 Bit position 7 6 5 4 3 2 1 0 Port Number 7 6 5 4 3 2 1 CPU
INT cat2600TsPingInterval	1.3.6.1.4.1.9.1.111.1.2.1.1.19	INTEGER	read-write	This variable specifies the interval in seconds of sending ICMP Echo Requests to the default gateway. No PING packets will be sent if the value is set to 0. The default interval is 10 minutes.
cat2600TsPipe	1.3.6.1.4.1.9.1.111.1.2.4
cat2600TsPipeEntry	1.3.6.1.4.1.9.1.111.1.2.4.1.1		not-accessible	Definition of each row in the TokenPipe table.
INT cat2600TsPipeNumber	1.3.6.1.4.1.9.1.111.1.2.4.1.1.1	INTEGER	read-only	The TokenPipe number for this row.
OCT cat2600TsPipePorts	1.3.6.1.4.1.9.1.111.1.2.4.1.1.2	OCTET STRING	read-write	The set of ports in this switch which are active in this Pipe. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16 (if available), etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the NWays LAN Switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
cat2600TsPipeTable	1.3.6.1.4.1.9.1.111.1.2.4.1		not-accessible	The TokenPipe table.
cat2600TsPort	1.3.6.1.4.1.9.1.111.1.2.2
INT cat2600TsPortAddrAgingTime	1.3.6.1.4.1.9.1.111.1.2.2.1.1.17	INTEGER	read-write	Port level address aging time.
MAC cat2600TsPortBeaconNAUN	1.3.6.1.4.1.9.1.111.1.2.2.1.1.34	MacAddr	not-accessible	MAC address of the NAUN station last generating a beacon MAC frame. This information is present for the generation of a trap and should not be used to represent the health of the ring.
MAC cat2600TsPortBeaconStationAddress	1.3.6.1.4.1.9.1.111.1.2.2.1.1.33	MacAddr	not-accessible	MAC address of the Station last generating a beacon MAC frame. This information is present for the generation of a trap and should not be used to represent the health of the ring.
INT cat2600TsPortBeaconType	1.3.6.1.4.1.9.1.111.1.2.2.1.1.35	INTEGER	not-accessible	The type of Beacon which last occurred. Values are the same as for the Beacon Type subvector and are defined as follows: X'0001' Issued by a Dual Ring Station during reconfiguration X'0002' Signal Loss X'0003' Timer TCT expired during claim token; no claim token frames recieved X'0004' Timer TCT expired during claim token; claim token frames recieved X'0005' TXI Access Protocol; Heart Beat Protocol Failure
INT cat2600TsPortCfgLoss	1.3.6.1.4.1.9.1.111.1.2.2.1.1.22	INTEGER	read-only	Number of events as described in TsPortCfgLossRC after the port has completed the join process and then lost communication.
INT cat2600TsPortCfgLossRC	1.3.6.1.4.1.9.1.111.1.2.2.1.1.23	INTEGER	read-only	Reason code describing the cause of configuration loss.
INT cat2600TsPortCfgLossSamplingPeriod	1.3.6.1.4.1.9.1.111.1.2.2.1.1.32	INTEGER	read-write	The sampling period, in minutes, for which the port monitors to see if the configuration loss threshold has been exceeeded.
INT cat2600TsPortCfgLossThreshold	1.3.6.1.4.1.9.1.111.1.2.2.1.1.31	INTEGER	read-write	Number of configuration loss events (described in TsPortCfgLossRC) during the sample period which, if exceeded, should cause the port to be disabled. If the port is disabled by this function the port must be manually re-enabled.
INT cat2600TsPortCfgRingSpeed	1.3.6.1.4.1.9.1.111.1.2.2.1.1.28	INTEGER	read-write	When read this object indicates the Port Ring Speed obtained by the RSA function. Write to this object when defining the Port Ring Speed for a fixed configuration (TsPortCfgRSA set to fixed(2)). When TsPortCfgRSA indicates fixed(2), this object is equivalent to the dtrMac MIB object cPortProtocolCharMediumRateOption and to dot5RingSpeed. Note that the syntax of these objects is different. For cPortProtocolCharMediumRateOption 1 indicates 4 Mb/s, while for TsPortCfgRingSpeed 1 indicates 16Mb/s. This object is a valid read object any time that TSPortLinkState indicates up(1)or when TsPortCfgRSA indicates fixed(2).
INT cat2600TsPortCfgRSA	1.3.6.1.4.1.9.1.111.1.2.2.1.1.29	INTEGER	read-write	User configured Ring Speed Adjust or fixed speed.
CTR cat2600TsPortCRCCount	1.3.6.1.4.1.9.1.111.1.2.2.1.1.24	Counter	read-only	Number of frames received with CRC error. This object is equivalent to dot5StatsLineError and to the dtrMac MIB object txiStatsLineErrorCounter.
INT cat2600TsPortDomain	1.3.6.1.4.1.9.1.111.1.2.2.1.1.30	INTEGER	read-only	Domain that the port belongs to.
INT cat2600TsPortDuplex	1.3.6.1.4.1.9.1.111.1.2.2.1.1.21	INTEGER	read-write	Version 1 MIB When read, this object indicates the Port Duplex state obtained by the auto-detect function. This object is a valid read object any time that TSPortLinkState indicates up(1) or when TsPortFixedCfg indicates fixed(2). Write to this object when defining the Port Duplex state for a fixed configuration (TsPortFixedCfg set to fixed(2)). Version 2 MIB This object is related to the dtrMac MIB objects cPortProtocolCharCurrentAccessProtocol and cPortProtocolCharAccessProtcolMask as defined in the following table: TsPortLinkState \| TsPortFixedCfg \| TsPortDuplex equivalent to: \| \| down \| auto \| CPortProtocolCharAccess \| \| ProtocolMask = X'0003' \| \| down \| fixed \| CPortProtocolCharAccess \| \| ProtocolMask = X'0001' or \| \| = X'0002' \| \| up \| auto \| cPortProtocolCharCurrent \| \| AccessProtocol \| \| up \| fixed \| cPortProtocolCharCurrent \| \| AccessProtocol.
cat2600TsPortEntry	1.3.6.1.4.1.9.1.111.1.2.2.1.1		not-accessible	Definition of rows in the port table. The number of rows is determined by the hardware and is specified by the value of cat2600TsNumPorts. Rows can not be created or deleted via SNMP requests.
INT cat2600TsPortFixedCfg	1.3.6.1.4.1.9.1.111.1.2.2.1.1.19	INTEGER	read-write	Use fixed configuration or run auto detection to determine configuration.
CTR cat2600TsPortForwardedFrames	1.3.6.1.4.1.9.1.111.1.2.2.1.1.3	Counter	read-only	Number of frames received on this port and forwarded to another port or the system module for processing.
CTR cat2600TsPortHashOverflows	1.3.6.1.4.1.9.1.111.1.2.2.1.1.16	Counter	read-only	Number of times a hash bucket was full when trying to add an entry to the port address table.
CTR cat2600TsPortHPChannelFrames	1.3.6.1.4.1.9.1.111.1.2.2.1.1.25	Counter	read-only	Number of frames sent to the high priority channel of the particular Token-Ring port.
INT cat2600TsPortHPThreshold	1.3.6.1.4.1.9.1.111.1.2.2.1.1.27	INTEGER	read-only	Priority level at which frames are sent to the High priority channel.
INT cat2600TsPortIndex	1.3.6.1.4.1.9.1.111.1.2.2.1.1.1	INTEGER	read-only	The ifIndex value corresponding to each port entry. For TR interfaces, the TsPortIndex corresponds to the Port Number or POE Index.
INT cat2600TsPortLinkState	1.3.6.1.4.1.9.1.111.1.2.2.1.1.15	INTEGER	read-only	Link state of the port.
CTR cat2600TsPortLocalStations	1.3.6.1.4.1.9.1.111.1.2.2.1.1.7	Counter	read-only	Number of stations on this port's address table which belong to the segment attached to this port.
CTR cat2600TsPortLPChannelFrames	1.3.6.1.4.1.9.1.111.1.2.2.1.1.26	Counter	read-only	Number of frames sent to the low priority channel of the particular Token-Ring port.
CTR cat2600TsPortMaxStations	1.3.6.1.4.1.9.1.111.1.2.2.1.1.5	Counter	read-only	Maximum number of stations which the port can support simultaneously.
INT cat2600TsPortMode	1.3.6.1.4.1.9.1.111.1.2.2.1.1.20	INTEGER	read-write	When read, this object indicates the Port Mode obtained by the auto-detect function. It is a valid read object only when TsPortFixedCfg is set to auto-detect(1) and TsPortLinkState indicates up(1). Write to this object when defining the Port Mode for a fixed configuration (TsPortFixedCfg set to fixed(2)). This object is equivalent to the dtrMac MIB object cPortProtocolCharOperationOption.
CTR cat2600TsPortMostStations	1.3.6.1.4.1.9.1.111.1.2.2.1.1.4	Counter	read-only	Highest number of stations ever active at any time since the last reset of the switch as seen by this port. This includes the default MAC address entries for the port.
CTR cat2600TsPortRcvBcasts	1.3.6.1.4.1.9.1.111.1.2.2.1.1.13	Counter	read-only	Number of Broadcast Frames received on this port without errors.
CTR cat2600TsPortRcvLocalFrames	1.3.6.1.4.1.9.1.111.1.2.2.1.1.2	Counter	read-only	Number of frames received where the destination is on this port.
CTR cat2600TsPortRemoteStations	1.3.6.1.4.1.9.1.111.1.2.2.1.1.8	Counter	read-only	Number of stations on this port's address table which belong to segments attached to other ports.
INT cat2600TsPortResetAddrs	1.3.6.1.4.1.9.1.111.1.2.2.1.1.12	INTEGER	read-write	Setting this object to reset(3) clears all address table entries for this port as well as setting all port traffic counters to zero and setting cat2600TsPortResetTimer to zero.
INT cat2600TsPortResetStats	1.3.6.1.4.1.9.1.111.1.2.2.1.1.10	INTEGER	read-write	Setting this object to reset(3) causes all traffic counters for this port to be set to zero. Also the value of cat2600TsPortResetTimer is set to zero.
TIK cat2600TsPortResetTimer	1.3.6.1.4.1.9.1.111.1.2.2.1.1.11	TimeTicks	read-only	Time (in 100th second ticks) since the port counters were reset.
MAC cat2600TsPortStnAddress	1.3.6.1.4.1.9.1.111.1.2.2.3.1.2	MacAddr	read-only	Station MAC address. Equivalent to ifPhysAddr for this port.
CTR cat2600TsPortStnDestnBytes	1.3.6.1.4.1.9.1.111.1.2.2.3.1.7	Counter	read-only	Number of bytes with this station as the destination.
CTR cat2600TsPortStnDestnFrames	1.3.6.1.4.1.9.1.111.1.2.2.3.1.6	Counter	read-only	Number of frames with this station as the destination.
cat2600TsPortStnEntry	1.3.6.1.4.1.9.1.111.1.2.2.3.1		not-accessible	Definition of rows in the port table. The number of rows is determined by the hardware and is specified by the value of cat2600TsNumPorts. Rows can not be created or deleted via SNMP requests.
INT cat2600TsPortStnLocation	1.3.6.1.4.1.9.1.111.1.2.2.3.1.3	INTEGER	read-only	Where the station is located.
INT cat2600TsPortStnPortNum	1.3.6.1.4.1.9.1.111.1.2.2.3.1.1	INTEGER	read-only	Port number corresponding to this entry.
CTR cat2600TsPortStnSrcBytes	1.3.6.1.4.1.9.1.111.1.2.2.3.1.5	Counter	read-only	Number of Bytes with this station as the source.
CTR cat2600TsPortStnSrcFrames	1.3.6.1.4.1.9.1.111.1.2.2.3.1.4	Counter	read-only	Number of frames with this station as the source.
cat2600TsPortStnTable	1.3.6.1.4.1.9.1.111.1.2.2.3		not-accessible	Port station table.
CTR cat2600TsPortSWHandledFrames	1.3.6.1.4.1.9.1.111.1.2.2.1.1.6	Counter	read-only	Number of Frames received on this port and delivered to the system module for processing.
CTR cat2600TsPortSwitchedFrames	1.3.6.1.4.1.9.1.111.1.2.2.1.1.14	Counter	read-only	Number of frames switched on this port
INT cat2600TsPortSwitchMode	1.3.6.1.4.1.9.1.111.1.2.2.1.1.18	INTEGER	read-write	Operational frame switching mode for the port. When in auto mode the port uses the Direct Cut algorithm to place the port in either cut-thru or store-and- forward mode. This object is equivalent to cPortProtocolCharFrameControlOption in the dtrMac MIB. However, this object defines an additional state -auto- not defined in that standard.
INT cat2600TsPortSwitchModeChangeTrapEnable	1.3.6.1.4.1.9.1.111.1.2.1.1.24	INTEGER	read-write	Enable or disable the trap sent out when the switching mode changes from cut-through to store and forward.
cat2600TsPortTable	1.3.6.1.4.1.9.1.111.1.2.2.1		not-accessible	A table of information about each port. The number of rows is given by cat2600TsNumPorts. (This value refers to PHYSICAL ports as opposed to internal logical CRF bridge ports.)
CTR cat2600TsPortUnknownStaFrames	1.3.6.1.4.1.9.1.111.1.2.2.1.1.9	Counter	read-only	Number of unicast frames received on this port and forwarded to the system module for processing because the source or destination station address is not in the port's forwarding table.
INT cat2600TsReset	1.3.6.1.4.1.9.1.111.1.2.1.2.5	INTEGER	read-write	This object is used to reset the switch. Writing softReset(3) causes the switch to reset the hardware, run quick diagnostics, clear all counters, start switching, issue a warmstart trap, and then be able to respond to SNMP requests. Writing hardReset(2) causes the switch to run power up diagnostics and then execute a soft reset. Note: all address tables are cleared in both cases. The administrative parameters from nonvolatile memory are used to initialize the operational parameters. The value returned on GETs should be running(1).
INT cat2600TsSamplingPeriod	1.3.6.1.4.1.9.1.111.1.2.1.1.26	INTEGER	read-write	Sampling period in minutes for determining if the error rate of CRC errors has been exceeded. The default value for this object is 10 minutes. The valid range is 1-120.
STR cat2600TsSerialNumber	1.3.6.1.4.1.9.1.111.1.2.1.1.3	DisplayString	read-only	System serial number.
cat2600TsSys	1.3.6.1.4.1.9.1.111.1.2.1.2
STR cat2600TsSysCurTime	1.3.6.1.4.1.9.1.111.1.2.1.2.13	DisplayString	read-write	Current time at the switch. To set the time use the format yyyy mm dd hh mm ss. All fields are required.
cat2600TsSysObjectID	1.3.6.1.4.1.9.1.111.1.1.1
INT cat2600TsSysTemperature	1.3.6.1.4.1.9.1.111.1.2.1.2.11	INTEGER	read-only	Temperature condition of the system. A change in this value generates a TRAP.
INT cat2600TsTapMonitoredPort	1.3.6.1.4.1.9.1.111.1.2.1.1.21	INTEGER	read-write	Allows the selection of the port that will be monitored by the port selected by cat2600TsTapPort.
INT cat2600TsTapPort	1.3.6.1.4.1.9.1.111.1.2.1.1.20	INTEGER	read-write	Select the port to monitor traffic.
STR cat2600TsTrapRcvrComm	1.3.6.1.4.1.9.1.111.1.2.1.1.14.1.4	DisplayString	read-write	Community string to use.
OCT cat2600TsTrapRcvrDmns	1.3.6.1.4.1.9.1.111.1.2.1.1.14.1.5	OCTET STRING	read-write	Domains on which traps to this target are sent. Each octet within the value of this object specifies a set of eight domains, with the first octet specifying domains 0 through 7, the second octet specifying domains 8 through 15, etc. Within each octet, the most significant bit represents the lowest numbered domain, and the least significant bit represents the highest numbered domain. Thus, each domain is represented by a single bit within the value of this object. If that bit has a value of '1' then that domain is included in the set of ports which will receive the trap; the domain is not included if its bit has a value of '0'.
cat2600TsTrapRcvrEntry	1.3.6.1.4.1.9.1.111.1.2.1.1.14.1		not-accessible	Definition of rows in the trap receiver table. The column cat2600TsTrapRcvrStatus is used to create and delete rows in the table. Creation requires a SET PDU with objects cat2600TsTrapRcvrStatus, cat2600TsTrapRcvrIpAddress, and cat2600TsTrapRcvrComm.
INT cat2600TsTrapRcvrIndex	1.3.6.1.4.1.9.1.111.1.2.1.1.14.1.1	INTEGER	read-only	The index of the row in the table.
IP cat2600TsTrapRcvrIpAddress	1.3.6.1.4.1.9.1.111.1.2.1.1.14.1.3	IpAddress	read-write	IP address for an SNMP manager that is to receive the trap.
INT cat2600TsTrapRcvrStatus	1.3.6.1.4.1.9.1.111.1.2.1.1.14.1.2	INTEGER	read-write	Setting the value of this object to invalid(3) deletes the row from the table. The value invalid(3) should never be returned on a GET. Setting this value to create(4) causes a new row to be created if the row does not already exist. To create a new row set cat2600TsTrapRcvrStatus to create(4) and cat2600TsTrapRcvrIndex to the next available index ( cat2600TsTrapRcvrNext ). After successful creation of the new row, you can then set the desired values for cat2600TsTrapRcvrIpAddress and cat2600TsTrapRcvrComm. The value returned on GETs should be valid(2) or other(1), which is used to indicate any other condition.
cat2600TsTrapRcvrTable	1.3.6.1.4.1.9.1.111.1.2.1.1.14		not-accessible	A table of managers to which to send traps. Entries in the table are saved across resets and power cycles.
INT cat2600TsTrendThreshold	1.3.6.1.4.1.9.1.111.1.2.1.1.25	INTEGER	read-write	Based on trend calculation of the Dynamic Cut State algorithm, when this value is exceeded the port changes from cut-through to store and forward mode. The default value for this object is 8 events. The valid range is 1-100.
cat2600TsUFC	1.3.6.1.4.1.9.1.111.1.2.6
cat2600TsUFCEntry	1.3.6.1.4.1.9.1.111.1.2.6.1.1		not-accessible	The objects contained in the UFC table.
STR cat2600TsUFCFwVer	1.3.6.1.4.1.9.1.111.1.2.6.1.1.7	DisplayString	read-only	The firmware version in the form major.minor.
STR cat2600TsUFCHwVer	1.3.6.1.4.1.9.1.111.1.2.6.1.1.6	DisplayString	read-only	The hardware version in the form major.minor.
STR cat2600TsUFCManufacturer	1.3.6.1.4.1.9.1.111.1.2.6.1.1.3	DisplayString	read-only	Firmware manufacturer.
INT cat2600TsUFCNumPhysIfs	1.3.6.1.4.1.9.1.111.1.2.6.1.1.2	INTEGER	read-only	The total number of physical network interfaces on the UFC. This count does not include the interface _OF_ the card or any logical interfaces which be _ON_ the card.
INT cat2600TsUFCReset	1.3.6.1.4.1.9.1.111.1.2.6.1.1.9	INTEGER	read-write	The object is used to reset a UFC. Writing a softReset(3) causes the switch to reset the hardware, run the minimum number of diagnostics, and clear all counters. Writing hardReset(2) causes the UFC to run power up diagnostics and then execute a softreset.
INT cat2600TsUFCSlotNum	1.3.6.1.4.1.9.1.111.1.2.6.1.1.1	INTEGER	read-only	The number of the slot in which the UFC is installed.
INT cat2600TsUFCStatus	1.3.6.1.4.1.9.1.111.1.2.6.1.1.8	INTEGER	read-only	The operational status of the UFC.
cat2600TsUFCTable	1.3.6.1.4.1.9.1.111.1.2.6.1		not-accessible	A table of the installed UFC cards in the switch. The number of entries in the table is given by cat2600TsNumberofUFCs.
OCT cat2600TsUFCType	1.3.6.1.4.1.9.1.111.1.2.6.1.1.4	OCTET STRING	read-only	The code representing what type of UFC is present. UFC codes are assigned by Cisco.
STR cat2600TsUFCTypeDesc	1.3.6.1.4.1.9.1.111.1.2.6.1.1.5	DisplayString	read-only	A text string describing what type of UFC is present.
catProd	1.3.6.1.4.1.9.1
cisco	1.3.6.1.4.1.9
dtrConcMIB	1.3.6.1.4.1.9.1.111.1.3.1
dtrMacMIB	1.3.6.1.4.1.9.1.111.1.3.2
dtrMIBs	1.3.6.1.4.1.9.1.111.1.3

RFC description

Manages Cisco Catalyst 2600 Token Ring switches with support for configuration, port settings, domains, and filtering capabilities.

Start monitoring Cisco Catalyst 2600 switching hub (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CAT2600-MIB

What Is CAT2600-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description