CTRON-SFPS-CONNECTION-MIB

All MIBs › CTRON-SFPS-CONNECTION-MIB

Category: Vendor: Cabletron/Enterasys

Description: Manages Cabletron SFPS connection configuration, admission control, and per-connection traffic parameters.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is CTRON-SFPS-CONNECTION-MIB?

CTRON-SFPS-CONNECTION-MIB is a Cabletron Systems vendor MIB for managing SFPS (Switched Fast Path Services / cell-switching fabric) connections, covering configuration and status of individual switched connections including source/destination and primary/secondary port pairs. It exposes a connection table capturing admission control parameters, control and admin status, and connection age. This MIB is primarily a connection-configuration/status MIB used to monitor whether individual switched paths through the fabric are up, correctly routed between the intended ports, and how long they have been established, which helps detect misconfigured or stale connections and admission-control failures. It has no explicitly stated dependency on other MIBs beyond general SMI/interface conventions typical of Cabletron's SFPS product line. It is deployed on Cabletron switching/fabric equipment providing path-switched connectivity in enterprise or carrier networks. Engineers can download the CTRON-SFPS-CONNECTION-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in CTRON-SFPS-CONNECTION-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Cabletron Systems SFPS switching fabric equipment

Monitoring Examples

An admin would poll sfpsConnectionTable/sfpsConnectionEntry to check sfpsConnectionSource and sfpsConnectionDestination against sfpsConnectionPrimInPort/sfpsConnectionPrimOutPort to confirm a connection is routed as expected. If sfpsConnectionCtrlStatus or sfpsConnectionAdminStatus shows the connection down while sfpsConnectionSecInPort/sfpsConnectionSecOutPort indicate a secondary path exists, that would reveal a failover to backup ports has occurred. sfpsConnectionAge would be checked to see how long a suspect connection has been established, useful for spotting stale or flapping connections.

What Can Be Monitored

connection source/destination
primary and secondary port assignment
connection control/admin status
connection age

Imported Objects

From CTRON-SFPS-INCLUDE-MIB

sfpsCNXPacketStats	OBJECT-IDENTITY
sfpsConnectionAPI	OBJECT-IDENTITY
sfpsConnectionConfigAPI	OBJECT-IDENTITY
sfpsConnectionLookupAPI	OBJECT-IDENTITY
sfpsConnectionQueryAPI	OBJECT-IDENTITY
sfpsConnectionStats	OBJECT-IDENTITY
sfpsConnectionTestAPI	OBJECT-IDENTITY
sfpsSwitchConnections	OBJECT-IDENTITY

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter
TimeTicks

From RFC1213-MIB

DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
sfpsConnectionTable	1.3.6.1.4.1.52.4.2.4.2.1.3.1		not-accessible	This table contains the connection information for all active connections on the SFPS access ports.
sfpsConnectionEntry	1.3.6.1.4.1.52.4.2.4.2.1.3.1.1		not-accessible	Each entry specifies the connection information for the active connection for which the entry exists.
ADR sfpsConnectionDestination	1.3.6.1.4.1.52.4.2.4.2.1.3.1.1.1	SfpsAddress	read-only	The destination SFPS address for this source/destination connection.
ADR sfpsConnectionSource	1.3.6.1.4.1.52.4.2.4.2.1.3.1.1.2	SfpsAddress	read-only	The source SFPS address for this source/destination connection.
INT sfpsConnectionPrimInPort	1.3.6.1.4.1.52.4.2.4.2.1.3.1.1.3	INTEGER	read-only	Identifies the primary inbound SFPS switch port.
INT sfpsConnectionPrimOutPort	1.3.6.1.4.1.52.4.2.4.2.1.3.1.1.4	INTEGER	read-only	Identifies the primary outbound SFPS switch port. All switched traffic for this connection will be transmitted on this outbound port.
INT sfpsConnectionSecInPort	1.3.6.1.4.1.52.4.2.4.2.1.3.1.1.5	INTEGER	read-only	Identifies the secondaryinbound SFPS switch port.
INT sfpsConnectionSecOutPort	1.3.6.1.4.1.52.4.2.4.2.1.3.1.1.6	INTEGER	read-only	Identifies the secondary outbound SFPS switch port. All switched traffic for this connection will be transmitted on this outbound port.
INT sfpsConnectionCtrlStatus	1.3.6.1.4.1.52.4.2.4.2.1.3.1.1.7	INTEGER	read-write	The control state of the SFPS connection.
INT sfpsConnectionAdminStatus	1.3.6.1.4.1.52.4.2.4.2.1.3.1.1.8	INTEGER	read-write	The administrative state of the SFPS connection.
TIK sfpsConnectionAge	1.3.6.1.4.1.52.4.2.4.2.1.3.1.1.9	TimeTicks	read-only	Indicates the age of the connection.
INT sfpsConnectionType	1.3.6.1.4.1.52.4.2.4.2.1.3.1.1.10	INTEGER	read-only	Sets the type of connection. Provisioned connections are setup manually; switched and vlan connections are setup dynammically.
CTR sfpsConnectionPkts	1.3.6.1.4.1.52.4.2.4.2.1.3.1.1.11	Counter	read-only	Indicates the total number of packets sent on this connection.
CTR sfpsConnectionBytes	1.3.6.1.4.1.52.4.2.4.2.1.3.1.1.12	Counter	read-only	Indicates the total number of bytes sent on this connection.
INT sfpsConnectionCanAge	1.3.6.1.4.1.52.4.2.4.2.1.3.1.1.13	INTEGER	read-only
STR sfpsConnectionPrimOutPorts	1.3.6.1.4.1.52.4.2.4.2.1.3.1.1.14	DisplayString	read-only	Identifies a list of outbound SFPS switch ports. All switched traffic for this connection will be transmitted on these outbound ports.
STR sfpsConnectionSecOutPorts	1.3.6.1.4.1.52.4.2.4.2.1.3.1.1.15	DisplayString	read-only	Identifies a list of outbound SFPS switch ports. All switched traffic for this connection will be transmitted on these outbound ports.
INT sfpsConnectionLookupAPIVerb	1.3.6.1.4.1.52.4.2.4.2.1.3.2.1	INTEGER	read-write	Specifies the action to be initiated as a result of setting this leaf.
ADR sfpsConnectionLookupAPIMacAddr	1.3.6.1.4.1.52.4.2.4.2.1.3.2.2	SfpsAddress	read-write	MAC address to be looked up as either the Source or Destination addresses.
ADR sfpsConnectionLookupAPIDestAddr	1.3.6.1.4.1.52.4.2.4.2.1.3.2.3	SfpsAddress	read-only	Destination MAC address
ADR sfpsConnectionLookupAPISourceAddr	1.3.6.1.4.1.52.4.2.4.2.1.3.2.4	SfpsAddress	read-only	Source MAC address
INT sfpsConnectionLookupAPIPrimInPort	1.3.6.1.4.1.52.4.2.4.2.1.3.2.5	INTEGER	read-only	Source port number
INT sfpsConnectionLookupAPIPrimOutPort	1.3.6.1.4.1.52.4.2.4.2.1.3.2.6	INTEGER	read-only	Destination port number. If -1, denotes multiple out ports.
INT sfpsConnectionLookupAPISecInPort	1.3.6.1.4.1.52.4.2.4.2.1.3.2.7	INTEGER	read-only	Source port number
INT sfpsConnectionLookupAPISecOutPort	1.3.6.1.4.1.52.4.2.4.2.1.3.2.8	INTEGER	read-only	Destination port number. If 01, denotes multiple out ports
INT sfpsConnectionLookupAPICtrlStatus	1.3.6.1.4.1.52.4.2.4.2.1.3.2.9	INTEGER	read-only	Control status
INT sfpsConnectionLookupAPIAdminStatus	1.3.6.1.4.1.52.4.2.4.2.1.3.2.10	INTEGER	read-only	Administrative status
TIK sfpsConnectionLookupAPIAge	1.3.6.1.4.1.52.4.2.4.2.1.3.2.11	TimeTicks	read-only	Age of connection
INT sfpsConnectionLookupAPIType	1.3.6.1.4.1.52.4.2.4.2.1.3.2.12	INTEGER	read-only	Type of connection
INT sfpsConnectionLookupAPIPkts	1.3.6.1.4.1.52.4.2.4.2.1.3.2.13	INTEGER	read-only	Number of packets switched on this connection
INT sfpsConnectionLookupAPIBytes	1.3.6.1.4.1.52.4.2.4.2.1.3.2.14	INTEGER	read-only	Number of bytes switched on this connection
INT sfpsConnectionLookupAPICanAge	1.3.6.1.4.1.52.4.2.4.2.1.3.2.15	INTEGER	read-only	Boolean to determine if this connection will be aged. True (1) means to age.
STR sfpsConnectionLookupAPIPrimOutPorts	1.3.6.1.4.1.52.4.2.4.2.1.3.2.16	DisplayString	read-only	If Primary OutPort is -1, the multiple outports will be displayed in text format
STR sfpsConnectionLookupAPISecOutPorts	1.3.6.1.4.1.52.4.2.4.2.1.3.2.17	DisplayString	read-only	If Secondary OutPort is -1, the multiple outports will be displayed in text format
INT sfpsConnectionConfigAPIVerb	1.3.6.1.4.1.52.4.2.4.2.1.3.3.1	INTEGER	read-write	Specifies the verb.
INT sfpsConnectionConfigAPICnxHiMark	1.3.6.1.4.1.52.4.2.4.2.1.3.3.2	INTEGER	read-write	Specifies the percentage of the Connection Table needed to be full before beginning aging.
INT sfpsConnectionConfigAPICnxNumToAge	1.3.6.1.4.1.52.4.2.4.2.1.3.3.3	INTEGER	read-write	Specifies the number of connections to age at each pass.
INT sfpsConnectionConfigAPIAgePeriod	1.3.6.1.4.1.52.4.2.4.2.1.3.3.4	INTEGER	read-write	Specifies the age period. Units in minutes. 0 - No periodic aging N - age every N minutes
INT sfpsConnectionConfigAPIAgePassInProgress	1.3.6.1.4.1.52.4.2.4.2.1.3.3.5	INTEGER	read-only	Specifies whether the age pass is in progress. 0 - not aging now 1 - aging now.
INT sfpsConnectionConfigAPICurCapacity	1.3.6.1.4.1.52.4.2.4.2.1.3.3.6	INTEGER	read-only	Specifies the percentage of the Connection Table used.
TIK sfpsConnectionConfigAPILastPassTime	1.3.6.1.4.1.52.4.2.4.2.1.3.3.7	TimeTicks	read-only	Specifies the time that the last age pass occured.
TIK sfpsConnectionConfigAPITimeSinceLastPass	1.3.6.1.4.1.52.4.2.4.2.1.3.3.8	TimeTicks	read-only	Specifies the time since the last age pass.
TIK sfpsConnectionConfigAPIAgePassDelta	1.3.6.1.4.1.52.4.2.4.2.1.3.3.9	TimeTicks	read-only	Specifies the time between the last two age passes.
INT sfpsConnectionConfigAPIAgePassCount	1.3.6.1.4.1.52.4.2.4.2.1.3.3.10	INTEGER	read-only	Specifies the number of aging passes that have occured.
INT sfpsConnectionConfigAPIAgeStatsHiMark	1.3.6.1.4.1.52.4.2.4.2.1.3.3.11	INTEGER	read-write
INT sfpsConnectionConfigAPIStatsAgingEnable	1.3.6.1.4.1.52.4.2.4.2.1.3.3.12	INTEGER	read-write
INT sfpsConnectionConfigAPIAgeStatsAgingSupported	1.3.6.1.4.1.52.4.2.4.2.1.3.3.13	INTEGER	read-only
INT sfpsConnectionConfigAPIIdleCnxs	1.3.6.1.4.1.52.4.2.4.2.1.3.3.14	INTEGER	read-only
INT sfpsConnectionConfigAPIActiveCnxs	1.3.6.1.4.1.52.4.2.4.2.1.3.3.15	INTEGER	read-only
INT sfpsConnectionStatsMaxCnxs	1.3.6.1.4.1.52.4.2.4.2.1.3.4.1	INTEGER	read-only	The maximum number of bi-directional connections allocated for the switch.
INT sfpsConnectionStatsTotalCnxs	1.3.6.1.4.1.52.4.2.4.2.1.3.4.2	INTEGER	read-only	The total number of bi-directional connections used in the switch.
INT sfpsConnectionStatsSwitchedCnxs	1.3.6.1.4.1.52.4.2.4.2.1.3.4.3	INTEGER	read-only	The number of bi-directional connections used in the switch with type
INT sfpsConnectionStatsVlanCnxs	1.3.6.1.4.1.52.4.2.4.2.1.3.4.4	INTEGER	read-only	The number of bi-directional connections used in the switch with type
INT sfpsConnectionStatsFilterCnxs	1.3.6.1.4.1.52.4.2.4.2.1.3.4.5	INTEGER	read-only	The number of bi-directional connections used in the switch with type
INT sfpsConnectionStatsSelfProgCnxs	1.3.6.1.4.1.52.4.2.4.2.1.3.4.6	INTEGER	read-only	The number of bi-directional connections used in the switch with type
INT sfpsConnectionStatsProvsnedCnxs	1.3.6.1.4.1.52.4.2.4.2.1.3.4.7	INTEGER	read-only	The number of bi-directional connections used in the switch with type
INT sfpsConnectionStatsTapCnxs	1.3.6.1.4.1.52.4.2.4.2.1.3.4.8	INTEGER	read-only	The number of bi-directional connections used in the switch with type
INT sfpsConnectionStatsMcastCnxs	1.3.6.1.4.1.52.4.2.4.2.1.3.4.9	INTEGER	read-only	The number of bi-directional connections used in the switch with type
INT sfpsConnectionStatsNetPortFilterCnxs	1.3.6.1.4.1.52.4.2.4.2.1.3.4.10	INTEGER	read-only	The number of bi-directional connections used in the switch with type
INT sfpsConnectionStatsNonCriticalVlans	1.3.6.1.4.1.52.4.2.4.2.1.3.4.11	INTEGER	read-only	Number of non-critical connections - these will be aged first
INT sfpsConnectionStatsAddErrors	1.3.6.1.4.1.52.4.2.4.2.1.3.4.12	INTEGER	read-only	Number of errors on adding a connnection
INT sfpsConnectionStatsDeleteErrors	1.3.6.1.4.1.52.4.2.4.2.1.3.4.13	INTEGER	read-only	Number of errors on deleting a connection
INT sfpsConnectionQueryAPIVerb	1.3.6.1.4.1.52.4.2.4.2.1.3.5.1	INTEGER	read-write	Specifies the action to be initiated as a result of setting this leaf.
ADR sfpsConnectionQueryAPIDestAddr	1.3.6.1.4.1.52.4.2.4.2.1.3.5.2	SfpsAddress	read-write	Destination MAC address.
ADR sfpsConnectionQueryAPISourceAddr	1.3.6.1.4.1.52.4.2.4.2.1.3.5.3	SfpsAddress	read-write	Source MAC address.
INT sfpsConnectionQueryAPIInPort	1.3.6.1.4.1.52.4.2.4.2.1.3.5.4	INTEGER	read-write	Source port number.
INT sfpsConnectionQueryAPIOutPort	1.3.6.1.4.1.52.4.2.4.2.1.3.5.5	INTEGER	read-write	Destination port number.
INT sfpsConnectionQueryAPICtrlStatus	1.3.6.1.4.1.52.4.2.4.2.1.3.5.6	INTEGER	read-only	Control Status
INT sfpsConnectionQueryAPIAdminStatus	1.3.6.1.4.1.52.4.2.4.2.1.3.5.7	INTEGER	read-only	Administrative Status.
INT sfpsConnectionQueryAPIAge	1.3.6.1.4.1.52.4.2.4.2.1.3.5.8	INTEGER	read-only	Age of connection.
INT sfpsConnectionQueryAPIQueryType	1.3.6.1.4.1.52.4.2.4.2.1.3.5.9	INTEGER	read-write	Type of connection.
INT sfpsConnectionQueryAPIOwner	1.3.6.1.4.1.52.4.2.4.2.1.3.5.10	INTEGER	read-only	Specifies whether or not Call control is owned by this agent switch. If the call is owned, then the switch will be responsible for releasing the call. This is used mainly when transferring call ownership in call re-routing and in setting up originating calls.
CTR sfpsConnectionQueryAPIPkts	1.3.6.1.4.1.52.4.2.4.2.1.3.5.11	Counter	read-only	Number of packets switched on this connection.
CTR sfpsConnectionQueryAPIBytes	1.3.6.1.4.1.52.4.2.4.2.1.3.5.12	Counter	read-only	Number of bytes switched on this connection.
INT sfpsConnectionQueryAPICanAge	1.3.6.1.4.1.52.4.2.4.2.1.3.5.13	INTEGER	read-only	Determine if this connection will be aged - (1) means to age.
STR sfpsConnectionQueryAPIOutPorts	1.3.6.1.4.1.52.4.2.4.2.1.3.5.14	DisplayString	read-write	If OutPorts is 1 - the multiple outports will be displayed in a text format.
ADR sfpsConnectionQueryAPIMacAddr	1.3.6.1.4.1.52.4.2.4.2.1.3.5.15	SfpsAddress	read-write	MAC address.
INT sfpsConnectionQueryAPISecInPort	1.3.6.1.4.1.52.4.2.4.2.1.3.5.16	INTEGER	read-only
INT sfpsConnectionQueryAPISecOutPort	1.3.6.1.4.1.52.4.2.4.2.1.3.5.17	INTEGER	read-only
STR sfpsConnectionQueryAPISecOutPorts	1.3.6.1.4.1.52.4.2.4.2.1.3.5.18	DisplayString	read-only
INT sfpsConnectionTestAPIVerb	1.3.6.1.4.1.52.4.2.4.2.1.3.6.1	INTEGER	read-write
INT sfpsConnectionTestAPIType	1.3.6.1.4.1.52.4.2.4.2.1.3.6.2	INTEGER	read-write
INT sfpsConnectionTestAPINumCnxs	1.3.6.1.4.1.52.4.2.4.2.1.3.6.3	INTEGER	read-write
ADR sfpsConnectionTestAPIMacAddr	1.3.6.1.4.1.52.4.2.4.2.1.3.6.4	SfpsAddress	read-write
INT sfpsConnectionTestAPIPort	1.3.6.1.4.1.52.4.2.4.2.1.3.6.5	INTEGER	read-write
INT sfpsAPIVerb	1.3.6.1.4.1.52.4.2.4.2.1.4.1	INTEGER	read-write	Specifies the action to be initiated as a result of setting this leaf.
SFP sfpsAPIInPort	1.3.6.1.4.1.52.4.2.4.2.1.4.2	SfpsSwitchPort	read-write	Specifies the ingress port of the switch.
INT sfpsAPIInHeaderType	1.3.6.1.4.1.52.4.2.4.2.1.4.3	INTEGER	read-write	Specfies the type of header being mapped.
INT sfpsAPIInHeaderLength	1.3.6.1.4.1.52.4.2.4.2.1.4.4	INTEGER	read-write	Specifies the length of the header value.
OCT sfpsAPIInHeaderValue	1.3.6.1.4.1.52.4.2.4.2.1.4.5	OCTET STRING	read-write	Specifies the actual inHeader value for the mapping.
SFP sfpsAPIOutPort	1.3.6.1.4.1.52.4.2.4.2.1.4.6	SfpsSwitchPort	read-write	Specifies the egress port of the switch.
INT sfpsAPIOutHeaderType	1.3.6.1.4.1.52.4.2.4.2.1.4.7	INTEGER	read-write	Specfies the type of header being mapped. This value defaults to the value given to sfpsAPIInHeaderType.
INT sfpsAPIOutHeaderLength	1.3.6.1.4.1.52.4.2.4.2.1.4.8	INTEGER	read-write	Specifies the length of the header value. This value defaults to the value given to sfpsAPIInHeaderLength.
OCT sfpsAPIOutHeaderValue	1.3.6.1.4.1.52.4.2.4.2.1.4.9	OCTET STRING	read-write	Specifies the actual outHeader value for the mapping. This value defaults to the value given to sfpsAPIInHeaderValue.
INT sfpsAPIArgumentDirection	1.3.6.1.4.1.52.4.2.4.2.1.4.10	INTEGER	read-write	Specifies the direction of the connection.
INT sfpsAPIArgumentOwner	1.3.6.1.4.1.52.4.2.4.2.1.4.11	INTEGER	read-write	Specifies whether or not callcontrol is owned by this agent switch. If the call is owned, then the switch will be responsible for releasing the call. THis is used mainly when transferring call ownership in call re-routing and in setting up originating calls.
INT sfpsAPIArgumentPriority	1.3.6.1.4.1.52.4.2.4.2.1.4.12	INTEGER	read-write	Specifies the outbound priority of the connection.
INT sfpsAPIType	1.3.6.1.4.1.52.4.2.4.2.1.4.13	INTEGER	read-write	Sets the type of connection that should be setup.
INT sfpsCNXPacketStatsVer1Tx	1.3.6.1.4.1.52.4.2.4.2.1.15.1	INTEGER	read-only	Version 1 transmission
INT sfpsCNXPacketStatsVer2Tx	1.3.6.1.4.1.52.4.2.4.2.1.15.2	INTEGER	read-only	Version 2 transmission
INT sfpsCNXPacketStatsVer1Rx	1.3.6.1.4.1.52.4.2.4.2.1.15.3	INTEGER	read-only	Version 1 receive
INT sfpsCNXPacketStatsVer2Rx	1.3.6.1.4.1.52.4.2.4.2.1.15.4	INTEGER	read-only	Version 2 receive
INT sfpsCNXPacketStatsOpCode1Tx	1.3.6.1.4.1.52.4.2.4.2.1.15.5	INTEGER	read-only	Operation code 1 transmission
INT sfpsCNXPacketStatsOpCode2Tx	1.3.6.1.4.1.52.4.2.4.2.1.15.6	INTEGER	read-only	Operation code 2 tranmission
INT sfpsCNXPacketStatsOpCode1Rx	1.3.6.1.4.1.52.4.2.4.2.1.15.7	INTEGER	read-only	Operation code 1 receive
INT sfpsCNXPacketStatsOpCode2Rx	1.3.6.1.4.1.52.4.2.4.2.1.15.8	INTEGER	read-only	Operation code 2 receive
INT sfpsCNXPacketStatsRxErrors	1.3.6.1.4.1.52.4.2.4.2.1.15.9	INTEGER	read-only	Receive errors

RFC description

Manages Fast Packet Switching Services connections, statistics, and API configuration on Cabletron Systems switches.

Start monitoring Cabletron SecureFast Packet Switch (SFPS), switched connections with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CTRON-SFPS-CONNECTION-MIB

What Is CTRON-SFPS-CONNECTION-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description