ADC-FLEXWAVE-URH-MIB

All MIBs › ADC-FLEXWAVE-URH-MIB

Organization: TE Connectivity

Last Updated: 2012-10-03

Category: Optical and WDM

Description: Manages ADC FlexWave Ultra Remote Head (URH) distributed antenna and remote radio unit configuration and status.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ADC-FLEXWAVE-URH-MIB?

ADC-FLEXWAVE-URH-MIB is a distributed antenna system (DAS) vendor MIB from ADC (now part of CommScope) for the FlexWave Prism and InterReach SPECTRUM Ultra Remote Head (URH) product line, remote radio head units used to extend cellular coverage. It exposes fault/alarm and trap data describing module identity and trap events, plus host unit (Hst) hardware objects such as unit reset control and backplane revision. Its principal use is fault and hardware-status monitoring: tracking alarmed module names/types, trap codes and sequence numbers to identify which remote radio module raised an alarm, and host unit hardware attributes to verify hardware health and recover a hung unit via remote reset. No explicit dependency on standard IETF MIBs is indicated in the available definitions, though it likely complements the vendor's broader FlexWave MIB suite. It is deployed in distributed antenna system installations (e.g., stadiums, campuses, buildings) where FlexWave URH remote radio heads relay cellular signal and must be centrally monitored for alarms and hardware faults, and administrators can get an ADC-FLEXWAVE-URH-MIB download to load its trap and hardware objects directly into a MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in ADC-FLEXWAVE-URH-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

ADC FlexWave Ultra Remote Head (URH) distributed antenna system remote radio unit

Monitoring Examples

An operator watching fwuTrapCode, fwuAlarmedModuleName, and fwuModuleType together with fwuTrapNodeAddress can pinpoint which remote head module raised an alarm and where it sits in the distributed antenna network. fwuTrapSequenceNumber and fwuTrapTimeStamp let them correlate the order and timing of alarms during a fault storm. If a host unit becomes unresponsive, fwuHstUnitReset can be used to remotely reset it, while fwuHstBackPlaneRev confirms hardware revision compatibility during troubleshooting.

What Can Be Monitored

alarm/trap codes and sequence
alarmed module identity and type
trap source node address
host unit backplane revision
host unit reset control/status

Imported Objects

From ADC-FWU-URH-TC-MIB

ALARMEnable
ALARMManage
ALARMType
BANDType
CATALOGType
CONTACTType
DELAYType
DuplexerType
ENETType
GAINType
LNAType
MODEType
MODULEType
OPTICSType
RauBandType
UnitID2
UnitID3
UnitType

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Counter64
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-IDENTITY
OBJECT-TYPE
TimeTicks
Unsigned32
enterprises

From SNMPv2-TC

DateAndTime
DisplayString
RowStatus
TEXTUAL-CONVENTION

How to Use in IPNetwork Monitor

Example using fwuHstSERFEthPortRxBytes OID:

Select an ADC/TE FlexWave DAS remote radio unit as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type fwuHstSERFEthPortRxBytes into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. It reports the count of the number of recieved bytes at this ethernet port. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter64-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
adc	1.3.6.1.4.1.2014
flexwave	1.3.6.1.4.1.2014.15
flexwaveurh	1.3.6.1.4.1.2014.15.2
flexwaveURHMibModule	1.3.6.1.4.1.2014.15.2.1			This is the MIB for managing entities associated with FlexWave Prism & InterReach SPECTRUM products for SW Version 8.1
fwuHostUnitObjects	1.3.6.1.4.1.2014.15.2.1.1
fwuHstSystemLevelObjects	1.3.6.1.4.1.2014.15.2.1.1.1
fwuHstSystemLevelInfo	1.3.6.1.4.1.2014.15.2.1.1.1.1
fwuHstGeneral	1.3.6.1.4.1.2014.15.2.1.1.1.1.1
INT fwuHstNumber	1.3.6.1.4.1.2014.15.2.1.1.1.1.1.1	INTEGER	read-only	Host Number.
STR fwuHstName	1.3.6.1.4.1.2014.15.2.1.1.1.1.1.2	DisplayString	read-write	User defined name of the host unit. All characters except angular brackets, single and double quotes are allowed. Minimum length of the name is 1 character. Maximum length of the name 64 characters.
INT fwuHstUnitReset	1.3.6.1.4.1.2014.15.2.1.1.1.1.1.3	INTEGER	read-write	Use to reset the Host. Do this by changing from normal(0) to reset(1). After the operation has completed the state automatically changes to normal.
STR fwuHstBackPlaneRev	1.3.6.1.4.1.2014.15.2.1.1.1.1.1.4	DisplayString	read-only	The back plane revision of the Host (It is the three pin version number of the chassis back plane).
ALA fwuHstAlarmStatusSummary	1.3.6.1.4.1.2014.15.2.1.1.1.1.1.5	ALARMType	read-only	Summary of alarm status on the Host.
STR fwuHstTempMeas	1.3.6.1.4.1.2014.15.2.1.1.1.1.1.6	DisplayString	read-only	Host system temperature value in Celsius.
ALA fwuSystemAlarmStatusSummary	1.3.6.1.4.1.2014.15.2.1.1.1.1.1.7	ALARMType	read-only	Summary of alarm status on the System. If there a unit in the system (Host and all remotes) with a fault condition, it will be reflected here. Severity is summarised by the highest severity of the alarms in the system. i.e. If there is at least one Major alarm, the summary will indicate Major Alarm. The severities supported are Major, Minor and OK.
OCT fwuHstSystemDateAndTime	1.3.6.1.4.1.2014.15.2.1.1.1.1.1.9	OCTET STRING	read-write	Date and Time settings on the system.
INT fwuAlarmAck	1.3.6.1.4.1.2014.15.2.1.1.1.1.1.11	INTEGER	read-write	Provision to acknowledgement one or all alarms in the system. Set 0 to acknowledge all alarms or the alarm code (numeric ID) of the alarm to be acknowledged. This is a integer greater than 0.
ALA fwuAlarmLevel	1.3.6.1.4.1.2014.15.2.1.1.1.1.1.12	ALARMType	read-write	Alarm status summary of system.
INT fwuUserCommLinkTest	1.3.6.1.4.1.2014.15.2.1.1.1.1.1.13	INTEGER	read-write	Provision to perform the system test manually. Set the value to 1 to initiate the test. Once started, the test cannot be cancelled. User has to wait for completion. On completion of the test, the value reverts back to 0. Use fwuUserCommLinkTestDartBandType or fwuUserCommLinkTestDartId to provide parameters for the test.
STR fwuUserLinkTestStatus	1.3.6.1.4.1.2014.15.2.1.1.1.1.1.14	DisplayString	read-only	Provides the status of the System/Link test, once the test has started. Start the test using fwuUserCommLinkTest. Status is reported in the format X;Y where X is the test status (number) and Y is the unit number. The valid values of the test status and their associated meaning. (0) - Test has not started. This is the default value. (1) - Test started. (2,3,4,5,6,7,8,9,10,11,12,13,14) - Test is in progress. (15) - Test completed. (16) - Test Failed.
BAN fwuUserCommLinkTestDartBandType	1.3.6.1.4.1.2014.15.2.1.1.1.1.1.15	BANDType	read-write	Bands on which the system test is to be run. Refer TC BANDType for list. 0 to select all provisioned bands for the test. If a non-zero value is provided here then fwuUserCommLinkTestDartId must be empty. If zero is provided here then fwuUserCommLinkTestDartId may be set to 0 or empty.
I32 fwuUserCommLinkTestDartId	1.3.6.1.4.1.2014.15.2.1.1.1.1.1.16	Integer32	read-write	Identify the DARTs on which the system test is to be run. It is the DART slot number on Host unit. Use 0 to select all provisioned DARTs for the test. Other valid values are 1 to 8 and -1. If a non-zero value is provided here then fwuUserCommLinkTestDartBandType must be empty. If zero is provided here then fwuUserCommLinkTestDartBandType may be set to 0 or empty.
INT fwuClearSysConfig	1.3.6.1.4.1.2014.15.2.1.1.1.1.1.17	INTEGER	read-write	To Clear System Configuration. Change the value from 0 to 1 to clear all the settings on the system. Also, known as Restore To Factory Defaults (RTFD).
DAT fwuLinkTestLastRuntime	1.3.6.1.4.1.2014.15.2.1.1.1.1.1.19	DateAndTime	read-only	Time indicating the most recent execution of System/Link Test.
STR fwuNTPServerIP	1.3.6.1.4.1.2014.15.2.1.1.1.1.1.20	DisplayString	read-write	IP address of NTP Server. Use internet dot-decimal notation when providing the address.
INT fwuSyncNTPServer	1.3.6.1.4.1.2014.15.2.1.1.1.1.1.21	INTEGER	read-write	Enable synchronization with NTP server. Change the value from 0 to 1 to enable synchronization with the NTP Server.
fwuHstExt	1.3.6.1.4.1.2014.15.2.1.1.1.1.2
CON fwuHstMajorContactAlarmOutput	1.3.6.1.4.1.2014.15.2.1.1.1.1.2.1	CONTACTType	read-only	Host Major contact output port state. Not present, OK and faulted are the supported states.
CON fwuHstMinorContactAlarmOutput	1.3.6.1.4.1.2014.15.2.1.1.1.1.2.2	CONTACTType	read-only	Host Minor contact output port state. Not present, OK and faulted are the supported states.
CON fwuRmtMajorContactAlarmOutput	1.3.6.1.4.1.2014.15.2.1.1.1.1.2.3	CONTACTType	read-only	Remote Major contact output port state. Not present, OK and faulted are the supported states.
CON fwuRmtMinorContactAlarmOutput	1.3.6.1.4.1.2014.15.2.1.1.1.1.2.4	CONTACTType	read-only	Remote Minor contact output port state. Not present, OK and faulted are the supported states.
fwuSystemActiveAlarms	1.3.6.1.4.1.2014.15.2.1.1.1.1.3
fwuSystemActiveAlarmTable	1.3.6.1.4.1.2014.15.2.1.1.1.1.3.1		not-accessible	This table lists all the outstanding (active) alarms in the system. Alarms are removed from this table when the alarm condition is cleared (i.e. When CLEAR is sent out).
fwuSystemActiveAlarmEntry	1.3.6.1.4.1.2014.15.2.1.1.1.1.3.1.1		not-accessible	Entries for active alarms.
U32 fwuSystemAlarmSequenceNumber	1.3.6.1.4.1.2014.15.2.1.1.1.1.3.1.1.1	Unsigned32	not-accessible	The number of the alarm table entry which is defined by this row.
UNI fwuSystemAlarmTrapNodeAddress	1.3.6.1.4.1.2014.15.2.1.1.1.1.3.1.1.2	UnitID2	read-only	System Node Address, where the alarm originated.
STR fwuSystemlabel	1.3.6.1.4.1.2014.15.2.1.1.1.1.3.1.1.3	DisplayString	read-only	The name used to identify the system. Since the Host name is used to identify the system, the Host name is reflected here.
STR fwuSystemAlarmRmtName	1.3.6.1.4.1.2014.15.2.1.1.1.1.3.1.1.4	DisplayString	read-only	Name of the unit from which the alarm originated.
UNI fwuSystemAlarmRmtType	1.3.6.1.4.1.2014.15.2.1.1.1.1.3.1.1.5	UnitType	read-only	Type of the unit from which the alarm originated. fwuSystemAlarmRmtName is the user provided name of this unit.
MOD fwuSystemAlarmModuleType	1.3.6.1.4.1.2014.15.2.1.1.1.1.3.1.1.6	MODULEType	read-only	Type of the Module from which the alarm originated. e.g SeRF, DART, SFP. To be read with fwuSystemAlarmRmtType. Then, it identifies the module on that (fwuSystemAlarmRmtType) unit.
U32 fwuSystemAlarmModuleNumber	1.3.6.1.4.1.2014.15.2.1.1.1.1.3.1.1.7	Unsigned32	read-only	Number of the module from which the alarm originated. To be used in conjuction with the object fwuSystemAlarmModuleType. So, if module type indicated DART and module number reported 3, then it means that the alarm originated from the third DART.
STR fwuSystemAlarmModuleName	1.3.6.1.4.1.2014.15.2.1.1.1.1.3.1.1.8	DisplayString	read-only	Name of the Module from which the alarm originated. The user provided name of the module identified by fwuSystemAlarmModuleNumber.
ALA fwuSystemAlarmSeverity	1.3.6.1.4.1.2014.15.2.1.1.1.1.3.1.1.9	ALARMType	read-only	Severity of the alarm.
STR fwuSystemAlarmRFBand	1.3.6.1.4.1.2014.15.2.1.1.1.1.3.1.1.10	DisplayString	read-only	The RF band affected by this alarm condition.
DAT fwuSystemAlarmTimeStamp	1.3.6.1.4.1.2014.15.2.1.1.1.1.3.1.1.11	DateAndTime	read-only	Time when the alarm is raised.
U32 fwuSystemAlarmHstNbr	1.3.6.1.4.1.2014.15.2.1.1.1.1.3.1.1.13	Unsigned32	read-only	Number identifying the host in the system.
UNI fwuSystemAlarmAnalogAddress	1.3.6.1.4.1.2014.15.2.1.1.1.1.3.1.1.14	UnitID3	read-only	Analog Portion of the node address.
fwuHstSystemLevelTraps	1.3.6.1.4.1.2014.15.2.1.1.1.2
NTF fwuHstModuleMissingFault	1.3.6.1.4.1.2014.15.2.1.1.1.2.2			Missing Host pluggable module.
NTF fwuHstOverTempFault	1.3.6.1.4.1.2014.15.2.1.1.1.2.3			Host Temperature above operating limit.
NTF fwuHstUnderTempFault	1.3.6.1.4.1.2014.15.2.1.1.1.2.4			Host Temperature below operating limit.
NTF fwuHstBTSUnderPowerFault	1.3.6.1.4.1.2014.15.2.1.1.1.2.5			Band specific alarm FLM raised when unit connected to BTS.
NTF fwuHstFLMDownconvertFailureFault	1.3.6.1.4.1.2014.15.2.1.1.1.2.6			Forward Link Monitor (FLM) fault active.
NTF fwuHstRLMUpconvertFailureFault	1.3.6.1.4.1.2014.15.2.1.1.1.2.7			Band specific alarm RLM raised when unit connected to BTS.
NTF fwuHstRLMUpConIndetFault	1.3.6.1.4.1.2014.15.2.1.1.1.2.8			Unable to run RLM due to Host Reverse gain being set too low.
NTF fwuHstIamAliveFault	1.3.6.1.4.1.2014.15.2.1.1.1.2.9			The Host I am alive Trap
fwuHstSERFObjects	1.3.6.1.4.1.2014.15.2.1.1.2
fwuHstSERFInfo	1.3.6.1.4.1.2014.15.2.1.1.2.1
fwuHstSERFGeneral	1.3.6.1.4.1.2014.15.2.1.1.2.1.1
STR fwuHstSERFLinuxKernelVer	1.3.6.1.4.1.2014.15.2.1.1.2.1.1.1	DisplayString	read-only	Linux Kernel version on host.
STR fwuHstSERFLinuxBootLoaderVer	1.3.6.1.4.1.2014.15.2.1.1.2.1.1.2	DisplayString	read-only	Boot Loader1 version on host.
STR fwuHstSERFCompactFlashSWVer	1.3.6.1.4.1.2014.15.2.1.1.2.1.1.3	DisplayString	read-only	Compact Flash version on host.
STR fwuHstSERFFPGAVer	1.3.6.1.4.1.2014.15.2.1.1.2.1.1.4	DisplayString	read-only	FPGA version loaded on Host SeRF.
STR fwuHstSERFPPCSNMPAgentSWVer	1.3.6.1.4.1.2014.15.2.1.1.2.1.1.5	DisplayString	read-only	SNMP agent version on host.
STR fwuHstSERFPPCHWMonSWVer	1.3.6.1.4.1.2014.15.2.1.1.2.1.1.6	DisplayString	read-only	Hardware Monitor process version on host.
STR fwuHstSERFPPCAPPMonSWVer	1.3.6.1.4.1.2014.15.2.1.1.2.1.1.7	DisplayString	read-only	Application Monitor process version on host.
STR fwuHstSERFPPCMATEMonSWVer	1.3.6.1.4.1.2014.15.2.1.1.2.1.1.8	DisplayString	read-only	Mate Monitor process version on host.
STR fwuHstSERFPPCENETMonSWVer	1.3.6.1.4.1.2014.15.2.1.1.2.1.1.9	DisplayString	read-only	Ethernet Monitor process version on host.
STR fwuHstSERFPPCFPGAMonSWVer	1.3.6.1.4.1.2014.15.2.1.1.2.1.1.10	DisplayString	read-only	FPGA Monitor process version on host.
STR fwuHstSERFRIDateCode	1.3.6.1.4.1.2014.15.2.1.1.2.1.1.11	DisplayString	read-only	Host SeRF Inventory - Date Code.
STR fwuHstSERFRIHWVer	1.3.6.1.4.1.2014.15.2.1.1.2.1.1.12	DisplayString	read-only	Host SeRF Inventory - Hardware version.
STR fwuHstSERFRISerialNumber	1.3.6.1.4.1.2014.15.2.1.1.2.1.1.13	DisplayString	read-only	Host SeRF Inventory - Serial Number.
STR fwuHstSERFRIADCPartNumber	1.3.6.1.4.1.2014.15.2.1.1.2.1.1.14	DisplayString	read-only	Host SeRF Inventory - TE PartNumber.
INT fwuHstSERFRIHWGen	1.3.6.1.4.1.2014.15.2.1.1.2.1.1.15	INTEGER	read-only	Host SeRF Hardware Generation.
STR fwuHstSERFLinuxBootLoaderFirstVer	1.3.6.1.4.1.2014.15.2.1.1.2.1.1.16	DisplayString	read-only	Boot Loader2 version of the host system.
STR fwuHstpThreadSWVer	1.3.6.1.4.1.2014.15.2.1.1.2.1.1.17	DisplayString	read-only	The version number of pThread process. If blank then pThread does not run here.
STR fwuHstSubagentSWVer	1.3.6.1.4.1.2014.15.2.1.1.2.1.1.18	DisplayString	read-only	The version number of the subagent.
STR fwuHstWebServerSWVer	1.3.6.1.4.1.2014.15.2.1.1.2.1.1.19	DisplayString	read-only	The version number of web server.
fwuHstSERFOptObjects	1.3.6.1.4.1.2014.15.2.1.1.2.1.2
fwuHstSERFOptTable	1.3.6.1.4.1.2014.15.2.1.1.2.1.2.1		not-accessible	This table maintains Information of Host SERF Optical Objects.
fwuHstSERFOptEntry	1.3.6.1.4.1.2014.15.2.1.1.2.1.2.1.1		not-accessible	Each entry in this table refers to Host SERF Optical objects.
I32 fwuHstSERFOptSFPNumber	1.3.6.1.4.1.2014.15.2.1.1.2.1.2.1.1.1	Integer32	read-only	SFP Number - Optical Port number.
STR fwuHstSERFOptSFPName	1.3.6.1.4.1.2014.15.2.1.1.2.1.2.1.1.2	DisplayString	read-write	User defined name of each Host SFP. All characters except angular brackets, single and double quotes are allowed. Minimum length of the name is 1 character. Maximum length of the name 64 characters.
OPT fwuHstSERFOptSFPType	1.3.6.1.4.1.2014.15.2.1.1.2.1.2.1.1.3	OPTICSType	read-only	SFP Type - Optical Port Type. Identifies whether the SFP is short(1)/intermediate(2)/long(3) range. It may also be unidentified (-1).
I32 fwuHstSERFOptSFPTxColor	1.3.6.1.4.1.2014.15.2.1.1.2.1.2.1.1.4	Integer32	read-only	Wavelength of light used in the SFP (in nanometers).
STR fwuHstSERFOptRevLaunchPowerMeas	1.3.6.1.4.1.2014.15.2.1.1.2.1.2.1.1.5	DisplayString	read-only	Value of the optical power, in dBm received at the host.
STR fwuHstSERFOptFwdLaunchPowerMeas	1.3.6.1.4.1.2014.15.2.1.1.2.1.2.1.1.6	DisplayString	read-only	Value of the optical power, in dBm transmitted by the host.
STR fwuHstSERFOptMateName	1.3.6.1.4.1.2014.15.2.1.1.2.1.2.1.1.7	DisplayString	read-only	Name of Host Mates.
INT fwuHstSERFIPEnable	1.3.6.1.4.1.2014.15.2.1.1.2.1.2.1.1.8	INTEGER	read-only	Indicates whether IP is enabled(1) or not(2).
UNI fwuHstSERFOptMateId	1.3.6.1.4.1.2014.15.2.1.1.2.1.2.1.1.9	UnitID2	read-only	Identifier of (companion) mate unit.
I32 fwuHstSERFOptMateSfpId	1.3.6.1.4.1.2014.15.2.1.1.2.1.2.1.1.10	Integer32	read-only	SFP slot number used at remote end.
fwuHstSERFTraps	1.3.6.1.4.1.2014.15.2.1.1.2.2
NTF fwuHstSERFSynthAlarmFault	1.3.6.1.4.1.2014.15.2.1.1.2.2.2			Host SeRF synthesizer unlocked.
NTF fwuHstSERFFault	1.3.6.1.4.1.2014.15.2.1.1.2.2.3			Summary of SeRF Synthesizer Unlocked alarm and SeRF FPGA status. The system may not be communicating with the Ethernet Switch. This fault is also precipitated by the I2C Bus Fault.
NTF fwuHstSERFRmtLostFault	1.3.6.1.4.1.2014.15.2.1.1.2.2.4			Remote is not communicating with Host.
NTF fwuHstSERFOptRxBERFault	1.3.6.1.4.1.2014.15.2.1.1.2.2.5			High bit error rate (BER) detected by fiber optic receiver.
NTF fwuHstSERFOptRxNoLightFault	1.3.6.1.4.1.2014.15.2.1.1.2.2.6			No signal detected by optical receiver.
NTF fwuHstSERFOptLaserFault	1.3.6.1.4.1.2014.15.2.1.1.2.2.7			SFP optical transmitter failed.
NTF fwuHstSERFOptOverDriveFault	1.3.6.1.4.1.2014.15.2.1.1.2.2.8			SFP optical receive input power above specification.
NTF fwuHstSERFOptUnderDriveFault	1.3.6.1.4.1.2014.15.2.1.1.2.2.9			SFP optical receive input power below specification.
NTF fwuHstSERFOptIpEnableFault	1.3.6.1.4.1.2014.15.2.1.1.2.2.10			Host SFP IPEnable Fault.
NTF fwuMastClockPriorityLvlConflict	1.3.6.1.4.1.2014.15.2.1.1.2.2.11			More than one Host has the same Master Clock Priority Level. All Hosts in conflict raise the alarm.
NTF fwuHstI2CBus1Fault	1.3.6.1.4.1.2014.15.2.1.1.2.2.12			Indicates an I2C communication problem.
NTF fwuHstI2CBus2Fault	1.3.6.1.4.1.2014.15.2.1.1.2.2.13			Indicates an I2C communication problem.
fwuHstSERFEthPortObjects	1.3.6.1.4.1.2014.15.2.1.1.3
fwuHstSERFEthPortInfo	1.3.6.1.4.1.2014.15.2.1.1.3.1
fwuHstSERFEthPortTable	1.3.6.1.4.1.2014.15.2.1.1.3.1.1		not-accessible	This table maintains information of Host Ethernet Ports.
fwuHstSERFEthPortEntry	1.3.6.1.4.1.2014.15.2.1.1.3.1.1.1		not-accessible	Each entry in this table refers to Host SERF Ethernet port objects.
U32 fwuHstSERFEthPortNumber	1.3.6.1.4.1.2014.15.2.1.1.3.1.1.1.1	Unsigned32	read-only	A unique identifier for each Ethernet port.
ENE fwuHstSERFEthPortType	1.3.6.1.4.1.2014.15.2.1.1.3.1.1.1.2	ENETType	read-only	An identifier for the type of Ethernet port. The port types are network(1), craft(2) , management(3) , switch(4) , SFP(5). It may be unknown (-1).
C64 fwuHstSERFEthPortRxBytesEx	1.3.6.1.4.1.2014.15.2.1.1.3.1.1.1.3	Counter64	read-only	Count of the number of recieved bytes at this ethernet port.
C64 fwuHstSERFEthPortRxPkts	1.3.6.1.4.1.2014.15.2.1.1.3.1.1.1.4	Counter64	read-only	The number of packets recieved at this ethernet port.
C64 fwuHstSERFEthPortRxFcsErrors	1.3.6.1.4.1.2014.15.2.1.1.3.1.1.1.5	Counter64	read-only	The number of FCS errors recieved at this ethernet port.
C64 fwuHstSERFEthPortRxBroadcastPkts	1.3.6.1.4.1.2014.15.2.1.1.3.1.1.1.6	Counter64	read-only	The number of broadcast packets recieved at this ethernet port.
C64 fwuHstSERFEthPortRxMulticastPkts	1.3.6.1.4.1.2014.15.2.1.1.3.1.1.1.7	Counter64	read-only	The number of multicast packets at this ethernet port.
C64 fwuHstSERFEthPortRxFragmtdFrames	1.3.6.1.4.1.2014.15.2.1.1.3.1.1.1.8	Counter64	read-only	The number of fragmented frames received at this ethernet port.
C64 fwuHstSERFEthPortRxJabbersFrames	1.3.6.1.4.1.2014.15.2.1.1.3.1.1.1.9	Counter64	read-only	The number of jabber frames received at this ethernet port.
C64 fwuHstSERFEthPortTxByteCounter	1.3.6.1.4.1.2014.15.2.1.1.3.1.1.1.10	Counter64	read-only	The number of bytes transmitted from this ethernet port.
C64 fwuHstSERFEthPortTxPkts	1.3.6.1.4.1.2014.15.2.1.1.3.1.1.1.11	Counter64	read-only	The number of packets transmitted from this ethernet port.
C64 fwuHstSERFEthPortTxBroadcastPkts	1.3.6.1.4.1.2014.15.2.1.1.3.1.1.1.12	Counter64	read-only	The number of broadcast packets transmitted from this ethernet port.
C64 fwuHstSERFEthPortTxMulticastPkts	1.3.6.1.4.1.2014.15.2.1.1.3.1.1.1.13	Counter64	read-only	The number of multicast packets transmitted from this ethernet port.
I32 fwuHstSERFEthPortSFPId	1.3.6.1.4.1.2014.15.2.1.1.3.1.1.1.14	Integer32	read-only	Identifies the SFP number to which this ethernet port connects.
fwuHstSERFEthPortTraps	1.3.6.1.4.1.2014.15.2.1.1.3.2
fwuHstSERFFPGAObjects	1.3.6.1.4.1.2014.15.2.1.1.4
fwuHstSERFFPGAInfo	1.3.6.1.4.1.2014.15.2.1.1.4.1
INT fwuHstSERFFPGAStatus	1.3.6.1.4.1.2014.15.2.1.1.4.1.1	INTEGER	read-only	Provides the SERF Card FPGA status. The status may be PPC can communicate with the FPGA (0) or not (1).
fwuHstSERFFPGATraps	1.3.6.1.4.1.2014.15.2.1.1.4.2
fwuHstMateMonObjects	1.3.6.1.4.1.2014.15.2.1.1.5
fwuHstMateMonInfo	1.3.6.1.4.1.2014.15.2.1.1.5.1
fwuHstMateMonTable	1.3.6.1.4.1.2014.15.2.1.1.5.1.1		not-accessible	This table maintains Information of Host Mate Monitor.
fwuHstMateMonEntry	1.3.6.1.4.1.2014.15.2.1.1.5.1.1.1		not-accessible	Each entry in this table refers to host Mate monitor objects.
UNI fwuHMmonRmtID	1.3.6.1.4.1.2014.15.2.1.1.5.1.1.1.1	UnitID2	read-only	ID of companion remote unit as Index of mate monitor table.
OCT fwuHMmonRmtIPAddress	1.3.6.1.4.1.2014.15.2.1.1.5.1.1.1.2	OCTET STRING	read-only	IP addresses of remote mate. This is a link-local address.
fwuHstDARTObjects	1.3.6.1.4.1.2014.15.2.1.1.6
fwuHstDARTInfo	1.3.6.1.4.1.2014.15.2.1.1.6.1
fwuHstDARTGeneral	1.3.6.1.4.1.2014.15.2.1.1.6.1.1
fwuHstDARTGeneralTable	1.3.6.1.4.1.2014.15.2.1.1.6.1.1.1		not-accessible	This table maintains Information of Host DART Card.
fwuHstDARTGeneralEntry	1.3.6.1.4.1.2014.15.2.1.1.6.1.1.1.1		not-accessible	Each entry in this table refers to host DART Card objects.
I32 fwuHstDARTNumber	1.3.6.1.4.1.2014.15.2.1.1.6.1.1.1.1.1	Integer32	read-only	A unique identifier for each DART. As there are eight DART slots, the number may be any of 1 to 8.
STR fwuHstDARTName	1.3.6.1.4.1.2014.15.2.1.1.6.1.1.1.1.2	DisplayString	read-create	A user defined name for each DART Card object of host. All characters except angular brackets, single and double quotes are allowed. Minimum length of the name is 1 character. Maximum length of the name 64 characters.
BAN fwuHstDARTBandType	1.3.6.1.4.1.2014.15.2.1.1.6.1.1.1.1.3	BANDType	read-only	Band type of host DART card.
OCT fwuHstDARTPassBand	1.3.6.1.4.1.2014.15.2.1.1.6.1.1.1.1.4	OCTET STRING	read-create	This is for configuration of Pass-band type for host DART card. Following input formats are supported for Classic and SuperDart passband configuration. 1. For Classic Darts only, User input string would be enumeration value ( i.e., 'x'), ranging from 1 to 134. See below in section 3. for valid values. 2. For SuperDarts only, a. BandType_SubBand1+SubBand2 This is applicable only for contiguous passband selection, applicable only for PCS & AWS. (e.g., 'PCS_A1+A2+A3') b. BandType_SubBand1+SubBand2:SubBand5+SubBand6 This is applicable for noncontiguous passband selection, applicable only for PCS & AWS. (e.g., 'PCS_A1+A2:C2+C1') c. BandType_StartFrequency-StartFrequency This is applicable only for contiguous passband frequency range. (e.g.,, PCS_1930-1945) d. BandType_StartFrequency1-StartFrequency1:StartFrequency2-StartFrequency2 This is applicable only for noncontiguous passband frequency ranges. (e.g., PCS_1930-1940.5:1960.7-1970.6). Where BandType is 'PCS', 'AWS', 'UMTS','EGSM900','GSM1800', 'UC700', 'LABC700'. 3. Valid enumeration value for classic dart:- undefined(-1), cellularA2A(1),cellularA(2),cellularAA1A2(3),cellularA1(4), cellularB(5),cellularB1(6),cellularBB1(7), pcsA1(8),pcsA2(9),pcsA3(10),pcsB1(11),pcsB2(12),pcsB3(13), pcsC3(14),pcsC4(15),pcsC5(16),pcsD(17),pcsE(18),pcsF(19), pcsG(20),awsH(21),pcsC2(22), pcsC1(23), pcsA1A2(24),pcsA2A3(25),pcsA3D(26),pcsDB1(27),pcsB1B2(28),pcsB2B3(29), pcsB3E(30),pcsEF(31),pcsFC3(32), pcsC3C4(33),pcsC4C5(34), pcsC5G(35),pcsGawsH(36),pcsFC2(37),pcsC1G(38),pcsA(39), pcsA2A3D(40),pcsA3DB1(41), pcsDB1B2(42),pcsB(43),pcsB2B3E(44), pcsB3EF(45),pcsEFC3(46),pcsFC3C4(47),pcsC(48), pcsC4C5G(49), pcsC5GawsH(50),pcsEFC2(51),pcsC1GawsH(52), pcsAD(53),pcsA2A3DB1(54),pcsA3DB1B2(55),pcsDB(56),pcsBE(57), pcsB2B3EF(58),pcsB3EFC3(59),pcsEFC3C4(60),pcsFC(61), pcsCG(62),pcsC4C5GawsH(63),pcsB3EFC2(64), pcsADB1(65),pcsA2A3DB1B2(66),pcsA3DB(67),pcsDBE(68), pcsBEF(69),pcsB2B3EFC3(70),pcsB3EFC3C4(71),pcsEFC(72), pcsFCG(73),pcsCGawsH(74),pcsB2B3EFC2(75), pcsADB1B2(76),pcsA2A3DB(77),pcsA3DBE(78),pcsDBEF(79), pcsBEFC3(80),pcsB2B3EFC3C4(81),pcsB3EFC(82), pcsEFCG(83),pcsFCGawsH(84),pcsADB(85), pcsA2A3DBE(86),pcsA3DBEF(87), pcsDBEFC3(88), pcsBEFC3C4(89),pcsB2B3EFC(90),pcsB3EFCG(91), pcsEFCGawsH(92),smrLow(93) , smrHigh( 94), awsA(95), awsAB(96), awsABC(97), awsABCD(98), awsABCDE(99), awsB(100), awsBC(101), awsBCD(102), awsBCDE(103), awsBCDEF(104), awsC(105), awsCD(106), awsCDE(107), awsCDEF(108), awsD(109), awsDE(110), awsDEF(111), awsE(112), awsEF(113), awsF(114), smrLowWide(115), cellularA2ABA1B1(116), GSM1800Low(117), GSM1800Middle(118), GSM1800High(119), umtsLow(120), umtsMiddle(121), umtsHigh(122), cellularAB(133), apac800iDEN(134).
MOD fwuHstDARTOperatingMode	1.3.6.1.4.1.2014.15.2.1.1.6.1.1.1.1.5	MODEType	read-create	Operating mode of the Host DART. The DART may be operating normally (1) or on standby (2). The mode may be undefined (-1).
INT fwuHstDARTDiversityStatus	1.3.6.1.4.1.2014.15.2.1.1.6.1.1.1.1.6	INTEGER	read-create	Diversity Status of host DART.
NUM fwuHstDARTForwardGain	1.3.6.1.4.1.2014.15.2.1.1.6.1.1.1.1.7	GAINType	read-create	Primary Gain in the forward path of Host DART. The range is 0-31dB with increments in steps of 1dB.
NUM fwuHstDARTReverseGain	1.3.6.1.4.1.2014.15.2.1.1.6.1.1.1.1.8	GAINType	read-create	Primary Gain in the reverse path of Host DART. The range is 0-31dB with increments in steps of 1dB.
INT fwuHstDARTFPGAStatus	1.3.6.1.4.1.2014.15.2.1.1.6.1.1.1.1.9	INTEGER	read-only	Host DART FPGA Status. It indicates whether the SeRF FPGA can talk to DART FPGA(0) or not (1).
STR fwuHstDARTFPGAProgramVer	1.3.6.1.4.1.2014.15.2.1.1.6.1.1.1.1.10	DisplayString	read-only	FPGA Version on the Host DART card.
STR fwuHstDARTRIADCPartNumber	1.3.6.1.4.1.2014.15.2.1.1.6.1.1.1.1.11	DisplayString	read-only	Host DART Inventory Data - TE Part Number.
STR fwuHstDARTRISerialNumber	1.3.6.1.4.1.2014.15.2.1.1.6.1.1.1.1.12	DisplayString	read-only	Host DART Inventory Data - Serial Number.
STR fwuHstDARTRIDateCode	1.3.6.1.4.1.2014.15.2.1.1.6.1.1.1.1.13	DisplayString	read-only	Host DART Inventory Data - DateCode.
STR fwuHstDARTRIHWVer	1.3.6.1.4.1.2014.15.2.1.1.6.1.1.1.1.14	DisplayString	read-only	Host DART Inventory Data - HW version.
ROW fwuHstDARTRowStatus	1.3.6.1.4.1.2014.15.2.1.1.6.1.1.1.1.15	RowStatus	read-create	The status of this conceptual row. It may be active or inactive.
STR fwuHstDARTPeakInputPwrLvl1	1.3.6.1.4.1.2014.15.2.1.1.6.1.1.1.1.16	DisplayString	read-only	Peak Input Power Level 1 to a Host DART.
STR fwuHstDARTPeakInputPwrLvl2	1.3.6.1.4.1.2014.15.2.1.1.6.1.1.1.1.17	DisplayString	read-only	Peak Input Power Level 2 to a Host DART. Incase of diversity, this value will be NA.
STR fwuHstDARTPeakAvgInputPwrLvl1	1.3.6.1.4.1.2014.15.2.1.1.6.1.1.1.1.18	DisplayString	read-only	Peak Average Input Power Level1 to a Host DART.
STR fwuHstDARTPeakAvgInputPwrLvl2	1.3.6.1.4.1.2014.15.2.1.1.6.1.1.1.1.19	DisplayString	read-only	Peak Average Input Power Level 2 to a Host DART. Incase of diversity, this value will be NA.
STR fwuHstDARTMinAvgInputPwrLvl1	1.3.6.1.4.1.2014.15.2.1.1.6.1.1.1.1.20	DisplayString	read-only	Minimum Average Input Power Level 1 to a Host DART.
STR fwuHstDARTMinAvgInputPwrLvl2	1.3.6.1.4.1.2014.15.2.1.1.6.1.1.1.1.21	DisplayString	read-only	Minimum Average Input Power Level 2 to a Host DART. Incase of diversity, this value will be NA.
INT fwuHstDARTInputPowerMode	1.3.6.1.4.1.2014.15.2.1.1.6.1.1.1.1.22	INTEGER	read-write	Host DART Input Power Level Mode. The supported modes are Snapshot(0) and Max Hold(1). When setting Max Hold, ensure that the status (fwuHstDARTDiversityStatus) is not diversity.
INT fwuHstDARTPwrLevelMaxHoldReset	1.3.6.1.4.1.2014.15.2.1.1.6.1.1.1.1.23	INTEGER	read-write	Provision to reset the Max Hold reading. Used when the input power mode is Max hold. Reset by changing from normal (0) to reset (1). Status will revert to normal once the reset is done. In snapshot mode (see fwuHstDARTInputPowerMode) this object is not applicable (-1).
OCT fwuHstDARTLastMaxHoldResetTime	1.3.6.1.4.1.2014.15.2.1.1.6.1.1.1.1.24	OCTET STRING	read-only	Date and Time of the last Max Hold reset on the host DART.
INT fwuHstDARTInputSrc	1.3.6.1.4.1.2014.15.2.1.1.6.1.1.1.1.25	INTEGER	read-write	To identify the input source; BTS(1) or BDA(2) and change it, if required.
fwuHstDARTTraps	1.3.6.1.4.1.2014.15.2.1.1.6.2
NTF fwuHstDARTDwnCon1SynLockFault	1.3.6.1.4.1.2014.15.2.1.1.6.2.2			DART downconverter 1 synthesizer unlocked.
NTF fwuHstDARTDwnCon2SynLockFault	1.3.6.1.4.1.2014.15.2.1.1.6.2.3			DART downconverter 2 synthesizer unlocked.
NTF fwuHstDARTUpConSynLockFault	1.3.6.1.4.1.2014.15.2.1.1.6.2.4			DART upconverter synthesizer unlocked.
NTF fwuHstDARTOverDriveFault	1.3.6.1.4.1.2014.15.2.1.1.6.2.5			DART forward RF input too high.
NTF fwuHstDARTUnderDriveFault	1.3.6.1.4.1.2014.15.2.1.1.6.2.6			DART forward RF input signal below the normal operating limit.
NTF fwuHstDARTFault	1.3.6.1.4.1.2014.15.2.1.1.6.2.7			Summary of DART Downconverter 1 Synthesizer Unlocked, Downconverter 2 Synthesizer Unlocked, Upconverter Synthesizer Unlocked, DC Supply Fault alarms, and DART FPGA status.
NTF fwuHstDARTDCSupplyFault	1.3.6.1.4.1.2014.15.2.1.1.6.2.8			DART card DC supply voltages outside specification.
NTF fwuHstDARTHardwareMismatchFault	1.3.6.1.4.1.2014.15.2.1.1.6.2.9			Host DART does not support the selected passband. Fault occurs when a Host DART is replaced with another DART of the incorrect type.
NTF fwuHstDARTALCLimitingFault	1.3.6.1.4.1.2014.15.2.1.1.6.2.10			Host DART forward path Automatic Level Control is active.
NTF fwuHstDARTLinkingConflictFault	1.3.6.1.4.1.2014.15.2.1.1.6.2.11			Host comes back up and finds that it cannot restore a link with a remote DART to which it was linked.
fwuHstSystemCardObjects	1.3.6.1.4.1.2014.15.2.1.1.7
fwuHstSystemCardInfo	1.3.6.1.4.1.2014.15.2.1.1.7.1
STR fwuHstSysCardRIADCPartNumber	1.3.6.1.4.1.2014.15.2.1.1.7.1.1	DisplayString	read-only	Host Inventory Data - TE Part Number.
STR fwuHstSysCardRISerialNumber	1.3.6.1.4.1.2014.15.2.1.1.7.1.2	DisplayString	read-only	Host Inventory Data - Serial Number.
STR fwuHstSysCardRIDateCode	1.3.6.1.4.1.2014.15.2.1.1.7.1.3	DisplayString	read-only	Host Inventory Data - Date Code.
STR fwuHstSysCardRIHWVer	1.3.6.1.4.1.2014.15.2.1.1.7.1.4	DisplayString	read-only	Host Inventory Data - Hardware version.
INT fwuHstSysCard10MhzRefClock	1.3.6.1.4.1.2014.15.2.1.1.7.1.5	INTEGER	read-write	System Card Reference clock. It may be set to internal (0) or external(1).
I32 fwuHstSysCardCPLevel	1.3.6.1.4.1.2014.15.2.1.1.7.1.6	Integer32	read-write	System Card Master Clock Priority Level prioritizes the system card clock using values 1 through 14 (Lower value is higher priority). This is primarily used in multihost systems. In such system, all hosts should have different priority levels, and the system inherently assures this. This entity allows the user to change the system set prioritization. Changeing values in a single host system has no change.
INT fwuHstSysCardOutputRefClock	1.3.6.1.4.1.2014.15.2.1.1.7.1.7	INTEGER	read-write	System Card Reference clock. System Board I supports only 10 MHz and System Board II supports both 10 MHz and 30 MHz Clock output. Default value is 1 for Host and 2 for DRU.
INT fwuHstSysCardRIHWGen	1.3.6.1.4.1.2014.15.2.1.1.7.1.8	INTEGER	read-only	Host System Card Hardware Generation. Presently, there are two generations; first Generation(0), second Generation(1)
fwuHstSystemCardTraps	1.3.6.1.4.1.2014.15.2.1.1.7.2
NTF fwuHstSysCardFanFault	1.3.6.1.4.1.2014.15.2.1.1.7.2.2			Fan not functioning.
NTF fwuHstSysCardClockMismatchFault	1.3.6.1.4.1.2014.15.2.1.1.7.2.3			System Card output clock not supported.
fwuRemoteUnitObjects	1.3.6.1.4.1.2014.15.2.1.2
fwuRmtSystemLevelObjects	1.3.6.1.4.1.2014.15.2.1.2.1
fwuRmtSystemLevelInfo	1.3.6.1.4.1.2014.15.2.1.2.1.1
fwuRmtGeneral	1.3.6.1.4.1.2014.15.2.1.2.1.1.1
fwuRmtGeneralTable	1.3.6.1.4.1.2014.15.2.1.2.1.1.1.1		not-accessible	This table maintains Information of remote.
fwuRmtGeneralEntry	1.3.6.1.4.1.2014.15.2.1.2.1.1.1.1.1		not-accessible	Each entry in this table refers to remote objects.
UNI fwuRmtNumber	1.3.6.1.4.1.2014.15.2.1.2.1.1.1.1.1.1	UnitID2	read-only	The Node address of connected remote.
CAT fwuRmtCatalogState	1.3.6.1.4.1.2014.15.2.1.2.1.1.1.1.1.2	CATALOGType	read-only	Catalog state of remote. If fwuRmtCatalogState is commission(2), then start commissioning on remote, else if it in normal, do not commission the remote.
STR fwuRmtName	1.3.6.1.4.1.2014.15.2.1.2.1.1.1.1.1.3	DisplayString	read-create	User defined name of the remote unit. All characters except angular brackets, single and double quotes are allowed. Minimum length of the name is 1 character. Maximum length of the name 64 characters.
ALA fwuRmtAlarmStatusSummary	1.3.6.1.4.1.2014.15.2.1.2.1.1.1.1.1.4	ALARMType	read-only	Summary of alarm status of all connected remote units.
STR fwuRmtTempMeasurement	1.3.6.1.4.1.2014.15.2.1.2.1.1.1.1.1.5	DisplayString	read-only	Temperature of each remote unit in Celsius. This value comes from the RSI.
ROW fwuRmtGeneralTableRowStatus	1.3.6.1.4.1.2014.15.2.1.2.1.1.1.1.1.6	RowStatus	read-create	The status of this conceptual row. It may be active or inactive.
UNI fwuRmtType	1.3.6.1.4.1.2014.15.2.1.2.1.1.1.1.1.7	UnitType	read-only	The type of Remote. e.g. Prism, DRU, HEU, IRU.
U32 fwuDruIfCombinerReboot	1.3.6.1.4.1.2014.15.2.1.2.1.1.1.1.1.8	Unsigned32	read-write	Reboot an IF-combiner and all the units connected to it. Only applicable to DRU-IFs Change Value from 0 to 1 to reboot.
INT fwuUsrCommLinkTestIFBr	1.3.6.1.4.1.2014.15.2.1.2.1.1.1.1.1.9	INTEGER	read-write	Provision to perform system test on an IF branch. Change from inactive(0) to start(1) to initiate the test. For the duration of the test inprogress(2) is displayed. On completion, inactive is displayed.
BAN fwuUsrCommLinkTestIFBrDType	1.3.6.1.4.1.2014.15.2.1.2.1.1.1.1.1.10	BANDType	read-write	Selected Bands i.e. RF DARTs on units when performing system test.
U32 fwuUsrCommLinkTestDartId	1.3.6.1.4.1.2014.15.2.1.2.1.1.1.1.1.11	Unsigned32	read-write	To identify the DART .
OCT fwuDruBackPlaneRev	1.3.6.1.4.1.2014.15.2.1.2.1.1.1.1.1.12	OCTET STRING	read-only	Provides the back plane revision of the DRU (Three pin version Number of the Chassis back plane)
INT fwuPrismUnitReset	1.3.6.1.4.1.2014.15.2.1.2.1.1.1.1.1.13	INTEGER	read-write	Provides a way to reset the Remote SERF card. SET this to reset(1) to trigger a remote unit reset.
fwuRmtSystemLevelTraps	1.3.6.1.4.1.2014.15.2.1.2.1.2
NTF fwuRmtAcPowerSupplyFault	1.3.6.1.4.1.2014.15.2.1.2.1.2.2			Summary of AC Power Supply 1, AC Power Supply 2, AC Power Supply 3, and AC Power Supply 4 alarms.
NTF fwuRmtMajorExtAlarmInputFault	1.3.6.1.4.1.2014.15.2.1.2.1.2.3			The remote Major Ext Alarm Input Fault.
NTF fwuRmtMinorExtAlarmInputFault	1.3.6.1.4.1.2014.15.2.1.2.1.2.4			The remote Minor Ext Alarm Input Fault.
NTF fwuRmtModuleMissingFault	1.3.6.1.4.1.2014.15.2.1.2.1.2.5			A Remote (DRU/PRU/URU) pluggable module is missing (if DRU: DART or SFP. If PRU/URU: DART, SFP, LNA, LPA, or PD).
NTF fwuRmtOverTempFault	1.3.6.1.4.1.2014.15.2.1.2.1.2.6			Remote Temperature above operating limit.
NTF fwuRmtUnderTempFault	1.3.6.1.4.1.2014.15.2.1.2.1.2.7			Temperature below operating limit.
NTF fwuRmtOpenDoorFault	1.3.6.1.4.1.2014.15.2.1.2.1.2.8			Door open on PRU.
NTF fwuRmtFanOverSpeedFault	1.3.6.1.4.1.2014.15.2.1.2.1.2.9			Fans operating above expected RPM.
NTF fwuRmtFanUnderSpeedFault	1.3.6.1.4.1.2014.15.2.1.2.1.2.10			Fans operating below expected RPM.
NTF fwuRmtDownLinkCalToneFailureFault	1.3.6.1.4.1.2014.15.2.1.2.1.2.11			Forward calibration tone not at expected level.
NTF fwuRmtUplinkFailureDetectLowFault	1.3.6.1.4.1.2014.15.2.1.2.1.2.12			Reverse test tone not at expected level.
NTF fwuRmtUpConvertFailureFault	1.3.6.1.4.1.2014.15.2.1.2.1.2.13			Band specific alarm raised during Forward Link Monitoring on PRU/URU.
NTF fwuRmtUnderPowerFault	1.3.6.1.4.1.2014.15.2.1.2.1.2.14			Band specific alarm raised during Forward Link Monitoring on PRU/URU.
NTF fwuRmtDownConvertFailureFault	1.3.6.1.4.1.2014.15.2.1.2.1.2.15			Band specific alarm raised during Reverse Link Monitoring on PRU/URU.
NTF fwuRmtUpconIndetFault	1.3.6.1.4.1.2014.15.2.1.2.1.2.16			Band specific alarm raised during Forward Link Monitoring on PRU/URU.
NTF fwuRmtFiberConnMismatchFault	1.3.6.1.4.1.2014.15.2.1.2.1.2.17			Fiber optic cable connections between cascaded DRU/PRUs not following SFP connection rules.
NTF fwuRmtExcessConnFault	1.3.6.1.4.1.2014.15.2.1.2.1.2.18			Two or more DRU/PRU/URU connected to a single cascaded DRU/PRU/URU, or a ninth DRU/PRU/URU connected in cascade.
NTF fwuRmtInvalidDevConnFault	1.3.6.1.4.1.2014.15.2.1.2.1.2.19			PRU/URU connected to a DRU or vice versa.
NTF fwuDruSysCardClockMismatchFault	1.3.6.1.4.1.2014.15.2.1.2.1.2.20			System Card output clock not supported.
NTF fwuDruNoCommsFault	1.3.6.1.4.1.2014.15.2.1.2.1.2.21			DRU has lost communication with IFEU Or IFEU is disconnected from the DRU.
NTF fwuSWVersionMismatchFault	1.3.6.1.4.1.2014.15.2.1.2.1.2.22			Software Version Mismatch Fault. SW Versions on the Host and Remote do not match.
NTF fwuDruSysCardFanFault	1.3.6.1.4.1.2014.15.2.1.2.1.2.23			Fan not functioning.
NTF fwuDruOverTempFault	1.3.6.1.4.1.2014.15.2.1.2.1.2.24			DRU Temperature above operating limit.
NTF fwuDruUnderTempFault	1.3.6.1.4.1.2014.15.2.1.2.1.2.25			DRU Temperature below operating limit.
fwuRmtSERFObjects	1.3.6.1.4.1.2014.15.2.1.2.2
fwuRmtSERFInfo	1.3.6.1.4.1.2014.15.2.1.2.2.1
fwuRmtSERFGeneral	1.3.6.1.4.1.2014.15.2.1.2.2.1.1
fwuRmtSERFGeneralTable	1.3.6.1.4.1.2014.15.2.1.2.2.1.1.1		not-accessible	This table maintains Information of remote SERF Card.
fwuRmtSERFGeneralEntry	1.3.6.1.4.1.2014.15.2.1.2.2.1.1.1.1		not-accessible	Each entry in this table refers to SERF Card objects.
STR fwuRmtSERFLinuxKernelVer	1.3.6.1.4.1.2014.15.2.1.2.2.1.1.1.1.1	DisplayString	read-only	Linux Kernel version on remote.
STR fwuRmtSERFLinuxBootLoaderVer	1.3.6.1.4.1.2014.15.2.1.2.2.1.1.1.1.2	DisplayString	read-only	Linux Boot loader version on remote.
STR fwuRmtSERFCompactFlashSWVer	1.3.6.1.4.1.2014.15.2.1.2.2.1.1.1.1.3	DisplayString	read-only	Compact Flash version on remote.
STR fwuRmtSERFFPGAVer	1.3.6.1.4.1.2014.15.2.1.2.2.1.1.1.1.4	DisplayString	read-only	Version of FPGA loaded on remote SeRF.
STR fwuRmtSERFPPCHWMonSWVer	1.3.6.1.4.1.2014.15.2.1.2.2.1.1.1.1.5	DisplayString	read-only	Hardware monitor process version on remote.
STR fwuRmtSERFPPCAPPMonSWVer	1.3.6.1.4.1.2014.15.2.1.2.2.1.1.1.1.6	DisplayString	read-only	Application monitor process version on remote.
STR fwuRmtSERFPPCMATEMonSWVer	1.3.6.1.4.1.2014.15.2.1.2.2.1.1.1.1.9	DisplayString	read-only	Mate monitor process version on remote.
STR fwuRmtSERFPPCENETMonSWVer	1.3.6.1.4.1.2014.15.2.1.2.2.1.1.1.1.10	DisplayString	read-only	ENET monitor process version on remote.
STR fwuRmtSERFPPCFPGAMonSWVer	1.3.6.1.4.1.2014.15.2.1.2.2.1.1.1.1.11	DisplayString	read-only	FPGA monitor process version on remote.
STR fwuRmtSERFRIDateCode	1.3.6.1.4.1.2014.15.2.1.2.2.1.1.1.1.12	DisplayString	read-only	Remote SERF Inventory - Date Code of the Remote system.
STR fwuRmtSERFRIHWVer	1.3.6.1.4.1.2014.15.2.1.2.2.1.1.1.1.13	DisplayString	read-only	Remote SERF Inventory - HardWare version of the remote system.
STR fwuRmtSERFRISerialNumber	1.3.6.1.4.1.2014.15.2.1.2.2.1.1.1.1.14	DisplayString	read-only	Remote SERF Inventory - Serial Number.
STR fwuRmtSERFRIADCPartNumber	1.3.6.1.4.1.2014.15.2.1.2.2.1.1.1.1.15	DisplayString	read-only	Remote SERF Inventory - TE PartNumber.
INT fwuRmtSERFRIHWGen	1.3.6.1.4.1.2014.15.2.1.2.2.1.1.1.1.16	INTEGER	read-only	Remote SERF Hardware Generation. Presently, there are two generations first generation(0), second generation(1)
STR fwuRmtpThreadSWVer	1.3.6.1.4.1.2014.15.2.1.2.2.1.1.1.1.17	DisplayString	read-only	The version number of pThread Process. If blank then pThread is not running.
STR fwuRmtWebServerSWVer	1.3.6.1.4.1.2014.15.2.1.2.2.1.1.1.1.18	DisplayString	read-only	The version number of Web Server on remote.
fwuRmtSERFOptObjects	1.3.6.1.4.1.2014.15.2.1.2.2.1.2
fwuRmtSERFOptTable	1.3.6.1.4.1.2014.15.2.1.2.2.1.2.1		not-accessible	This table maintains Information of remote units SFP objects.
fwuRmtSERFOptEntry	1.3.6.1.4.1.2014.15.2.1.2.2.1.2.1.1		not-accessible	Each entry in this table refers to remote units SFP objects.
I32 fwuRmtSERFOptSFPNumber	1.3.6.1.4.1.2014.15.2.1.2.2.1.2.1.1.1	Integer32	read-only	A unique identifier of each SFP. The identifier is the SFP slot number. There are eight slots. Therefore, the valid values are 1 to 8.
STR fwuRmtSERFOptSFPName	1.3.6.1.4.1.2014.15.2.1.2.2.1.2.1.1.2	DisplayString	read-write	User defined name of each Remote SFP. All characters except angular brackets, single and double quotes are allowed. Minimum length of the name is 1 character. Maximum length of the name 64 characters.
OPT fwuRmtSERFOptSFPType	1.3.6.1.4.1.2014.15.2.1.2.2.1.2.1.1.3	OPTICSType	read-only	SFP Type - Optical Port Type. Identifies whether the SFP is short(1)/intermediate(2)/long(3) range. It may also be unidentified (-1).
I32 fwuRmtSERFOptSFPColor	1.3.6.1.4.1.2014.15.2.1.2.2.1.2.1.1.4	Integer32	read-only	Wavelength of light used in the SFP (in nanometers).
STR fwuRmtSERFOptRevLaunchPowerMeas	1.3.6.1.4.1.2014.15.2.1.2.2.1.2.1.1.5	DisplayString	read-only	Value of the optical power, in dBm received at the remote.
STR fwuRmtSERFOptFwdLaunchPowerMeas	1.3.6.1.4.1.2014.15.2.1.2.2.1.2.1.1.6	DisplayString	read-only	Value of the optical power, in dBm transmitted by the remote.
STR fwuRmtSERFOptMateName	1.3.6.1.4.1.2014.15.2.1.2.2.1.2.1.1.7	DisplayString	read-only	Name of Remote mate.
INT fwuRmtSERFIPEnable	1.3.6.1.4.1.2014.15.2.1.2.2.1.2.1.1.8	INTEGER	read-only	IP enable mode.
UNI fwuRmtSERFOptMateId	1.3.6.1.4.1.2014.15.2.1.2.2.1.2.1.1.9	UnitID2	read-only	Identifier of (companion) mate unit.
I32 fwuRmtSERFOptMateSfpId	1.3.6.1.4.1.2014.15.2.1.2.2.1.2.1.1.10	Integer32	read-only	Identifier of SFP to which the mate connects.
INT fwuRmtSERFOptMateSfpDir	1.3.6.1.4.1.2014.15.2.1.2.2.1.2.1.1.11	INTEGER	read-only	Indicates whether the fiber is incoming(from the direction of the host) (0) or outgoing (away from the unit)(1) on this SFP port.
OCT fwuRmtSERFOptHostIP	1.3.6.1.4.1.2014.15.2.1.2.2.1.2.1.1.12	OCTET STRING	read-only	IP addresses of Host. If 'NA', then it means that no host is connected.
fwuRmtSERFTraps	1.3.6.1.4.1.2014.15.2.1.2.2.2
NTF fwuRmtSERFHstLostFault	1.3.6.1.4.1.2014.15.2.1.2.2.2.2			Host not communicating with DRU/PRU/URU.
NTF fwuRmtSERFOptRxBERFault	1.3.6.1.4.1.2014.15.2.1.2.2.2.3			High bit error rate (BER) detected by fiber optic receiver.
NTF fwuRmtSERFOptRxNoLightFault	1.3.6.1.4.1.2014.15.2.1.2.2.2.4			No signal detected by optical receiver.
NTF fwuRmtSERFOptLaserFault	1.3.6.1.4.1.2014.15.2.1.2.2.2.5			SFP optical transmitter failed.
NTF fwuRmtSERFOptOverDriveFault	1.3.6.1.4.1.2014.15.2.1.2.2.2.6			SFP optical receive input power above specification.
NTF fwuRmtSERFOptUnderDriveFault	1.3.6.1.4.1.2014.15.2.1.2.2.2.7			SFP optical receive input power below specification.
NTF fwuRmtSERFSynthAlarmFault	1.3.6.1.4.1.2014.15.2.1.2.2.2.8			SeRF synthesizer unlocked.
NTF fwuRmtSERFFault	1.3.6.1.4.1.2014.15.2.1.2.2.2.9			Summary of SeRF Synthesizer Unlocked alarm and SeRF FPGA status. Possibly, the system may not be communicating with the Ethernet Switch. This is also precipitated by the I2C Bus Fault.
NTF fwuRmtI2CBus1Fault	1.3.6.1.4.1.2014.15.2.1.2.2.2.10			Indicates an I2C communication problem.
NTF fwuRmtI2CBus2Fault	1.3.6.1.4.1.2014.15.2.1.2.2.2.11			Indicates an I2C communication problem.
fwuRmtSERFEthPortObjects	1.3.6.1.4.1.2014.15.2.1.2.3
fwuRmtSERFEthPortInfo	1.3.6.1.4.1.2014.15.2.1.2.3.1
fwuRmtSERFEthPortTable	1.3.6.1.4.1.2014.15.2.1.2.3.1.1		not-accessible	This table maintains information of Host Ethernet Ports.
fwuRmtSERFEthPortEntry	1.3.6.1.4.1.2014.15.2.1.2.3.1.1.1		not-accessible	Each entry in this table refers to Host SERF Ethernet port objects.
U32 fwuRmtSERFEthPortNumber	1.3.6.1.4.1.2014.15.2.1.2.3.1.1.1.1	Unsigned32	read-only	A unique identifier for each Ethernet port. There are twelve ports.
ENE fwuRmtSERFEthPortType	1.3.6.1.4.1.2014.15.2.1.2.3.1.1.1.2	ENETType	read-only	An identifier for the type of Ethernet port. The port types are network(1), craft(2) , management(3) , switch(4) , SFP(5). It may be unknown (-1).
C64 fwuRmtSERFEthPortRxBytes	1.3.6.1.4.1.2014.15.2.1.2.3.1.1.1.3	Counter64	read-only	The number of bytes recieved at this ethernet port.
C64 fwuRmtSERFEthPortRxPkts	1.3.6.1.4.1.2014.15.2.1.2.3.1.1.1.4	Counter64	read-only	The number of packets recieved at this ethernet port.
C64 fwuRmtSERFEthPortRxFcsErrors	1.3.6.1.4.1.2014.15.2.1.2.3.1.1.1.5	Counter64	read-only	The number of FCS errors recieved at this ethernet port.
C64 fwuRmtSERFEthPortRxBroadcastPkts	1.3.6.1.4.1.2014.15.2.1.2.3.1.1.1.6	Counter64	read-only	The number of broadcast packets recieved at this ethernet port.
C64 fwuRmtSERFEthPortRxMulticastPkts	1.3.6.1.4.1.2014.15.2.1.2.3.1.1.1.7	Counter64	read-only	The number of multicast packets recieved at this ethernet port.
C64 fwuRmtSERFEthPortRxFragmtdFrames	1.3.6.1.4.1.2014.15.2.1.2.3.1.1.1.8	Counter64	read-only	The number of fragmented frames received at this ethernet port.
C64 fwuRmtSERFEthPortRxJabbersFrames	1.3.6.1.4.1.2014.15.2.1.2.3.1.1.1.9	Counter64	read-only	The number of jabber frames received at this ethernet port.
C64 fwuRmtSERFEthPortTxByteCounter	1.3.6.1.4.1.2014.15.2.1.2.3.1.1.1.10	Counter64	read-only	The number of bytes transmitted from this ethernet port.
C64 fwuRmtSERFEthPortTxPkts	1.3.6.1.4.1.2014.15.2.1.2.3.1.1.1.11	Counter64	read-only	The number of packets transmitted from this ethernet port.
C64 fwuRmtSERFEthPortTxBroadcastPkts	1.3.6.1.4.1.2014.15.2.1.2.3.1.1.1.12	Counter64	read-only	The number of broadcast packets transmitted from this ethernet port.
C64 fwuRmtSERFEthPortTxMulticastPkts	1.3.6.1.4.1.2014.15.2.1.2.3.1.1.1.13	Counter64	read-only	The number of multicast packets transmitted from this ethernet port.
I32 fwuRmtSERFEthPortSFPId	1.3.6.1.4.1.2014.15.2.1.2.3.1.1.1.14	Integer32	read-only	Identifier of SFP to which this ethernet port connects to.
fwuRmtSERFEthPortTraps	1.3.6.1.4.1.2014.15.2.1.2.3.2
fwuRmtSERFFPGAObjects	1.3.6.1.4.1.2014.15.2.1.2.4
fwuRmtSERFFPGAInfo	1.3.6.1.4.1.2014.15.2.1.2.4.1
fwuRmtSERFFPGAInfoTable	1.3.6.1.4.1.2014.15.2.1.2.4.1.1		not-accessible	This table maintains Information of remote SERF FPGA objects.
fwuRmtSERFFPGAInfoEntry	1.3.6.1.4.1.2014.15.2.1.2.4.1.1.1		not-accessible	Each entry in this table refers to SERF FPGA information.
INT fwuRmtSERFFPGAStatus	1.3.6.1.4.1.2014.15.2.1.2.4.1.1.1.1	INTEGER	read-only	Remote SERF Card FPGA status. Either the ppc can talk to FPGA(0) or not(1)
fwuRmtSERFFPGATraps	1.3.6.1.4.1.2014.15.2.1.2.4.2
fwuRmtDARTObjects	1.3.6.1.4.1.2014.15.2.1.2.6
fwuRmtDARTInfo	1.3.6.1.4.1.2014.15.2.1.2.6.1
fwuRmtDARTGeneral	1.3.6.1.4.1.2014.15.2.1.2.6.1.1
fwuRmtDARTGeneralTable	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1		not-accessible	This table maintains Information of Remote DART Card.
fwuRmtDARTGeneralEntry	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1		not-accessible	Each entry in this table refers to remote DART Card objects.
I32 fwuRmtDARTNumber	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.1	Integer32	read-only	A unique identifier for each DART Card Object of remote. Since there are eight DART slots the valid values are 1 to 8.
STR fwuRmtDARTName	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.2	DisplayString	read-create	A user defined name for each DART Card object of remote. All characters except angular brackets, single and double quotes are allowed. Minimum length of the name is 1 character. Maximum length of the name 64 characters.
BAN fwuRmtDARTBandType	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.3	BANDType	read-only	Band type of remote DART card.
OCT fwuRmtDARTPassBand	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.4	OCTET STRING	read-create	This is for configuration of Pass-band type for Remote DART card. Following input formats are supported for Classic and SuperDart passband configuration. 1. For Classic Darts only, User input string would be enumeration value ( i.e., 'x'), ranging from 1 to 134. See below in section 3. for valid values. 2. For SuperDarts only, a. BandType_SubBand1+SubBand2 This is applicable only for contiguous passband selection, applicable only for PCS & AWS. (e.g., 'PCS_A1+A2+A3') b. BandType_SubBand1+SubBand2:SubBand5+SubBand6 This is applicable for noncontiguous passband selection, applicable only for PCS & AWS. (e.g., 'PCS_A1+A2:C2+C1') c. BandType_StartFrequency-StartFrequency This is applicable only for contiguous passband frequency range. (e.g.,, PCS_1930-1945) d. BandType_StartFrequency1-StartFrequency1:StartFrequency2-StartFrequency2 This is applicable only for noncontiguous passband frequency ranges. (e.g., PCS_1930-1940.5:1960.7-1970.6). Where BandType is 'PCS', 'AWS', 'UMTS','EGSM900','GSM1800', 'UC700'. 3. Valid enumeration value for classic dart:- undefined ( -1 ), cellularA2A(1),cellularA(2),cellularAA1A2(3),cellularA1(4), cellularB(5),cellularB1(6),cellularBB1(7), pcsA1(8),pcsA2(9),pcsA3(10),pcsB1(11),pcsB2(12),pcsB3(13), pcsC3(14),pcsC4(15),pcsC5(16),pcsD(17),pcsE(18),pcsF(19), pcsA1A2(24),pcsA2A3(25),pcsA3D(26),pcsDB1(27),pcsB1B2(28),pcsB2B3(29), pcsB3E(30),pcsEF(31),pcsFC3(32),pcsC3C4(33),pcsC4C5(34), pcsC5G(35),pcsGawsH(36),pcsFC2(37),pcsC1G(38),pcsA(39), pcsA2A3D(40),pcsA3DB1(41),pcsDB1B2(42),pcsB(43),pcsB2B3E(44), pcsB3EF(45),pcsEFC3(46),pcsFC3C4(47),pcsC(48), pcsC4C5G(49), pcsC5GawsH(50),pcsEFC2(51),pcsC1GawsH(52), pcsAD(53),pcsA2A3DB1(54),pcsA3DB1B2(55),pcsDB(56),pcsBE(57), pcsB2B3EF(58),pcsB3EFC3(59),pcsEFC3C4(60),pcsFC(61), pcsCG(62),pcsC4C5GawsH(63),pcsB3EFC2(64), pcsADB1(65),pcsA2A3DB1B2(66),pcsA3DB(67),pcsDBE(68), pcsBEF(69),pcsB2B3EFC3(70),pcsB3EFC3C4(71),pcsEFC(72), pcsFCG(73),pcsCGawsH(74),pcsB2B3EFC2(75), pcsADB1B2(76),pcsA2A3DB(77),pcsA3DBE(78),pcsDBEF(79), pcsBEFC3(80),pcsB2B3EFC3C4(81),pcsB3EFC(82), pcsEFCG(83),pcsFCGawsH(84),pcsADB(85), pcsA2A3DBE(86),pcsA3DBEF(87),pcsDBEFC3(88), pcsBEFC3C4(89),pcsB2B3EFC(90),pcsB3EFCG(91), pcsEFCGawsH(92),smrLow(93) , smrHigh( 94), awsA(95), awsAB(96), awsABC(97), awsABCD(98), awsABCDE(99), awsB(100), awsBC(101), awsBCD(102), awsBCDE(103), awsBCDEF(104), awsC(105), awsCD(106), awsCDE(107), awsCDEF(108), awsD(109), awsDE(110), awsDEF(111), awsE(112), awsEF(113), awsF(114), smrLowWide(115), cellularA2ABA1B1(116), GSM1800Low(117), GSM1800Middle(118), GSM1800High(119), umtsLow(120), umtsMiddle(121), umtsHigh(122), cellularAB(133), apac800iDEN(134)
MOD fwuRmtDARTOperatingMode	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.5	MODEType	read-create	Operating mode of remote DART card. The DART may be operating normally (1) or on standby (2). The mode may be undefined (-1).
INT fwuRmtDARTDiversityStatus	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.6	INTEGER	read-create	Diversity Status of remote DART card.
NUM fwuRmtDARTForwardGain	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.7	GAINType	read-create	Primary Gain in forward path of remote DART card. The range is 0-31dB with increments in steps of 1dB.
NUM fwuRmtDARTReverseGain	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.8	GAINType	read-only	Primary Gain in reverse path of remote DART card.
DEL fwuRmtDARTForwardDelay	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.9	DELAYType	read-create	Forward delay in micro seconds on the remote DART. If the delay setting is outside the valid range of delay values then ranging fault will be raised if the Remote Dart is Linked.
DEL fwuRmtDARTReverseDelay	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.10	DELAYType	read-create	Reverse delay in micro seconds on the remote DART. If the delay setting is outside the valid range of delay values then ranging fault will be raised if the Remote Dart is Linked.
STR fwuRmtDARTTempMeas	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.11	DisplayString	read-only	Temperature of Remote DART in degree Celsius.
INT fwuRmtDARTFPGAStatus	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.12	INTEGER	read-only	Remote DART FPGA Status. It indicates if the SERF FPGA can talk(0) or not talk(1)to DART FPGA .
STR fwuRmtDARTFPGAProgramVer	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.13	DisplayString	read-only	FPGA version on the remote DART.
STR fwuRmtDARTRIADCPartNumber	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.14	DisplayString	read-only	Remote DART Inventory Data - TE Part Number.
STR fwuRmtDARTRISerialNumber	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.15	DisplayString	read-only	Remote DART Inventory Data - Serial Number.
STR fwuRmtDARTRIDateCode	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.16	DisplayString	read-only	Remote DART Inventory Data - DateCode.
STR fwuRmtDARTRIHWVer	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.17	DisplayString	read-only	Remote DART Inventory Data - HW version.
ROW fwuRmtDARTGeneralTableRowStatus	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.18	RowStatus	read-create	The status of this conceptual row.
I32 fwuRmtDARTActualForwardDelay	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.19	Integer32	read-only	This is the forward delay on Remote DART.
I32 fwuRmtDARTForwardLowerboundDelay	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.20	Integer32	read-only	This is the lower bound of the Forward Delay values.
I32 fwuRmtDARTForwardUpperboundDelay	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.21	Integer32	read-only	This is the upper bound of the Forward Delay values.
I32 fwuRmtDARTActualReverseDelay	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.22	Integer32	read-only	This is the Reverse delay on Remote DART.
I32 fwuRmtDARTReverseLowerboundDelay	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.23	Integer32	read-only	This is the lower bound of the Reverse delay values.
I32 fwuRmtDARTReverseUpperboundDelay	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.24	Integer32	read-only	This is the upper bound of the Reverse delay values.
STR fwuRmtDARTPeakInputPwrLvl1	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.25	DisplayString	read-only	Peak Input Power Level 1 to a Remote DART.
STR fwuRmtDARTPeakInputPwrLvl2	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.26	DisplayString	read-only	Peak Input Power Level 2 to the Remote DART.
STR fwuRmtDARTPeakAvgInputPwrLvl1	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.27	DisplayString	read-only	Peak Average Input Power Level 1 to the Remote DART.
STR fwuRmtDARTPeakAvgInputPwrLvl2	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.28	DisplayString	read-only	Peak Average Input Power Level 2 to the Remote DART.
STR fwuRmtDARTMinAvgInputPwrLvl1	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.29	DisplayString	read-only	Minimum Average Input Power Level 1 to the Remote DART.
STR fwuRmtDARTMinAvgInputPwrLvl2	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.30	DisplayString	read-only	Minimum Average Input Power Level 2 to the Remote DART.
INT fwuRmtDARTInputPowerMode	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.31	INTEGER	read-write	Remote DART Input Power Level Mode. Two modes are supported Snapshot(0) and Max Hold(1).
INT fwuRmtDARTPwrLevelMaxHoldReset	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.32	INTEGER	read-write	Provision to reset the Max Hold reading. Used when the input power mode is Max hold. Reset by changing from normal (0) to reset (1). Status will revert to normal once the reset is done. In snapshot mode (see fwuRmtDARTInputPowerMode) this object is not applicable (-1).
OCT fwuRmtDARTLastMaxHoldResetTime	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.33	OCTET STRING	read-only	Date and Time of the last maxHold reset on the remote DART.
INT fwuRmtDARTReverseGainMode	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.34	INTEGER	read-write	The gain modes on the Reverse Path. Two modes are supported, Normal(0) and High(1). It is applicable to all RF modules but not to IF DARTs.
STR fwuRmtDARTTxRIADCPartNumber	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.35	DisplayString	read-only	Remote Inventory Data - TE Part Number [Tx Board]. Field will have value only if Tx Board is present.
STR fwuRmtDARTTxRISerialNumber	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.36	DisplayString	read-only	Remote Inventory Data - Serial Number [Tx Board]. Field will have value only if Tx Board is present.
STR fwuRmtDARTTxRIDateCode	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.37	DisplayString	read-only	Remote Inventory Data - DateCode [Tx Board]. Field will have value only if Tx Board is present.
STR fwuRmtDARTTxRIHWVer	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.38	DisplayString	read-only	Remote Inventory Data - HW version [Tx Board]. Field will have value only if Tx Board is present.
INT fwuRmtDARTLinkedStatus	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.39	INTEGER	read-only	Indicates if the DART is linked (1) or not (0).
INT fwuRmtDARTAvailable	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.40	INTEGER	read-only	Indicates if the DART is available for use (1) or not (0).
INT fwuRmtDARTUsedSFP	1.3.6.1.4.1.2014.15.2.1.2.6.1.1.1.1.41	INTEGER	read-only	Indicates the SFP (number) used by a DART to link. There are eight possible SFP numbers. Therefore, the valid values are 1 to 8.
fwuRmtDARTTraps	1.3.6.1.4.1.2014.15.2.1.2.6.2
NTF fwuRmtDARTDwnCon1SynLockFault	1.3.6.1.4.1.2014.15.2.1.2.6.2.2			Lock state of the first down converter synthesizer.
NTF fwuRmtDARTDwnCon2SynLockFault	1.3.6.1.4.1.2014.15.2.1.2.6.2.3			DART downconverter 2 synthesizer unlocked.
NTF fwuRmtDARTUpConSynLockFault	1.3.6.1.4.1.2014.15.2.1.2.6.2.4			DART downconverter 2 synthesizer unlocked.
NTF fwuRmtDARTDCSupplyFault	1.3.6.1.4.1.2014.15.2.1.2.6.2.5			DART card DC supply voltages outside specification.
NTF fwuRmtDARTFault	1.3.6.1.4.1.2014.15.2.1.2.6.2.6			Summary of DART Downconverter 1 Synthesizer Unlocked, Downconverter 2 Synthesizer Unlocked, Upconverter Synthesizer Unlocked, DC Supply Fault alarms, and DART FPGA status.
NTF fwuRmtDARTHardwareMismatchFault	1.3.6.1.4.1.2014.15.2.1.2.6.2.7			Remote DART does not support the selected passband. Fault occurs when a Remote DART is replaced with another DART of the incorrect type.
NTF fwuRmtRangingFault	1.3.6.1.4.1.2014.15.2.1.2.6.2.8			DRU/PRU/URU delay settings outside the valid range.
NTF fwuRmtDARTOverTempFault	1.3.6.1.4.1.2014.15.2.1.2.6.2.9			Remote DART temperature above operating limit.
NTF fwuRmtDARTLowTempFault	1.3.6.1.4.1.2014.15.2.1.2.6.2.10			Remote DART temperature below operating limit.
NTF fwuRmtDARTUplinkInactivityFault	1.3.6.1.4.1.2014.15.2.1.2.6.2.11			No uplink activity is detected for one hour.
NTF fwuRmtDARTCommsFault	1.3.6.1.4.1.2014.15.2.1.2.6.2.12			The Remote DART communication path is missing or incorrect.
fwuRmtLPAObjects	1.3.6.1.4.1.2014.15.2.1.2.8
fwuRmtLPAInfo	1.3.6.1.4.1.2014.15.2.1.2.8.1
fwuRmtLPAInfoTable	1.3.6.1.4.1.2014.15.2.1.2.8.1.1		not-accessible	This table maintains Information of remote LPA objects.
fwuRmtLPAInfoEntry	1.3.6.1.4.1.2014.15.2.1.2.8.1.1.1		not-accessible	Each entry in this table refers to LPA objects.
I32 fwuRmtLPANumber	1.3.6.1.4.1.2014.15.2.1.2.8.1.1.1.1	Integer32	read-only	A unique identifier for an LPA.
INT fwuRmtLPAReset	1.3.6.1.4.1.2014.15.2.1.2.8.1.1.1.2	INTEGER	read-write	Provision to reset the LPA. Change from normal(0) to reset(1) to perform a reset of the LPA. Resetting the LPA when it is offline will place in an operating state.
INT fwuRmtLPAOpState	1.3.6.1.4.1.2014.15.2.1.2.8.1.1.1.3	INTEGER	read-only	Identifies the LPA Operating mode. The modes are operating (0) and offline (1). The operating state is controlled by fwuRmtLPAControl. Also, see fwuRmtLPAReset.
STR fwuRmtLPAPartNum	1.3.6.1.4.1.2014.15.2.1.2.8.1.1.1.4	DisplayString	read-only	Remote LPA Part Number.
STR fwuRmtLPASerialNum	1.3.6.1.4.1.2014.15.2.1.2.8.1.1.1.5	DisplayString	read-only	Remote LPA Serial Number.
STR fwuRmtLPAHWVer	1.3.6.1.4.1.2014.15.2.1.2.8.1.1.1.6	DisplayString	read-only	Remote LPA Hardware version.
STR fwuRmtLPASWVer	1.3.6.1.4.1.2014.15.2.1.2.8.1.1.1.7	DisplayString	read-only	Remote LPA Software version.
STR fwuRmtLPADescr	1.3.6.1.4.1.2014.15.2.1.2.8.1.1.1.8	DisplayString	read-only	Remote LPA Description.
INT fwuRmtLPAControl	1.3.6.1.4.1.2014.15.2.1.2.8.1.1.1.9	INTEGER	read-write	Provision to control the operating mode of remote LPA. When the control is set to normal (0), the operating mode is operating. When the control is set to offline (1), the operating mode is standby. fwuRmtLPAOpState will reflect the change in state/mode when the values are changed for this entity.
STR fwuRmtLPAMaxOpPwr	1.3.6.1.4.1.2014.15.2.1.2.8.1.1.1.10	DisplayString	read-only	Maximum Output power for the LPA. This object is applicable for HDMs also.
DUP fwuRmtLPABandType	1.3.6.1.4.1.2014.15.2.1.2.8.1.1.1.11	DuplexerType	read-only	LPA hardware type. Valid LPA Types are cellularA(1), cellularB(2), smrLow(3), smrHigh(4), pcs(5), aws(6), smrLowWide(7), fullCellular(8), gsm1800(9), umts(10), egsm900(11), lowerABC(12), upperC700(13), apac800iDEN(14), prismSmr800and900(15), prismSmr900and800(16), prismSmr800(17), cellularApac(18), apacEgsm900(19), pGsmEgsm900(20)
fwuRmtLPATraps	1.3.6.1.4.1.2014.15.2.1.2.8.2
NTF fwuRmtLPADisableFault	1.3.6.1.4.1.2014.15.2.1.2.8.2.2			PRU/URU Linear Power Amplifier (LPA) disabled due to an internally detected problem. (VSWR, DC, Loop Fault, Low Power, or Temperature High alarm).
NTF fwuRmtLPAOverPowerFault	1.3.6.1.4.1.2014.15.2.1.2.8.2.3			PRU/URU Linear Power Amplifier (LPA) output power level above operating limit.
NTF fwuRmtLPAHighTempFault	1.3.6.1.4.1.2014.15.2.1.2.8.2.4			LPA High Temperature Fault.
NTF fwuRmtLPAVswrFault	1.3.6.1.4.1.2014.15.2.1.2.8.2.5			PRU/URU Linear Power Amplifier (LPA) VSWR fault.
NTF fwuRmtLPADcFault	1.3.6.1.4.1.2014.15.2.1.2.8.2.6			PRU/URU Linear Power Amplifier (LPA) DC fault.
NTF fwuRmtLPALoopFault	1.3.6.1.4.1.2014.15.2.1.2.8.2.7			PRU/URU Linear Power Amplifier (LPA) Loop fault.
NTF fwuRmtLPALowPowerFault	1.3.6.1.4.1.2014.15.2.1.2.8.2.8			Internal low power fault state of linear power amplifier (the gain of one or more internal amplifiers does not meet specification).
NTF fwuRmtLPADetectFault	1.3.6.1.4.1.2014.15.2.1.2.8.2.9			Linear Power Amplifier (LPA) detection fault. LPA missing from remote.
NTF fwuRmtPaOverCurrentFault	1.3.6.1.4.1.2014.15.2.1.2.8.2.10			PA reported fault.
fwuRmtPwrDetectorBoardObjects	1.3.6.1.4.1.2014.15.2.1.2.9
fwuRmtPwrDetectorBoardInfo	1.3.6.1.4.1.2014.15.2.1.2.9.1
fwuRmtPwrDetectorBoardInfoTable	1.3.6.1.4.1.2014.15.2.1.2.9.1.1		not-accessible	This table maintains Information of remote power detector board objects.
fwuRmtPwrDetectorBoardInfoEntry	1.3.6.1.4.1.2014.15.2.1.2.9.1.1.1		not-accessible	Each entry in this table refers to power detector board objects.
I32 fwuRmtPowerDetectorNumber	1.3.6.1.4.1.2014.15.2.1.2.9.1.1.1.1	Integer32	read-only	A unique identifier for each power detector.
STR fwuRmtSystemVswrMeas	1.3.6.1.4.1.2014.15.2.1.2.9.1.1.1.2	DisplayString	read-only	VSWR (Voltage Standing Wave Ratio) measured in the system.
STR fwuRmtRFPowerOutputMeas	1.3.6.1.4.1.2014.15.2.1.2.9.1.1.1.3	DisplayString	read-only	The value of Remote RF Power Output, in dBm.
STR fwuRmtPwrDetectorBoardRIADCPartNum	1.3.6.1.4.1.2014.15.2.1.2.9.1.1.1.4	DisplayString	read-only	Power Detector Inventory - TE Part Number.
STR fwuRmtPwrDetectorBoardRISerialNum	1.3.6.1.4.1.2014.15.2.1.2.9.1.1.1.5	DisplayString	read-only	Power Detector Inventory - Serial Number.
STR fwuRmtPwrDetectorBoardRIDateCode	1.3.6.1.4.1.2014.15.2.1.2.9.1.1.1.6	DisplayString	read-only	Power Detector Inventory - Date Code.
STR fwuRmtPwrDetectorBoardRIHWVer	1.3.6.1.4.1.2014.15.2.1.2.9.1.1.1.7	DisplayString	read-only	Power Detector Inventory - HW version.
STR fwuRmtPwrDetectorNoRfPowerThershold	1.3.6.1.4.1.2014.15.2.1.2.9.1.1.1.8	DisplayString	read-write	Threshold value for RF No Power. The minimum threshold value is 0dBm and maximum threshold value is 100dBm.
STR fwuRmtSystemVSWRThreshold	1.3.6.1.4.1.2014.15.2.1.2.9.1.1.1.9	DisplayString	read-write	User set VSWR threshold value. User is to provide the VSWR value in the form x.y:1. If the value is provided as x:1 then it will be represented as x.0:1. The minimum threshold value is 2.0 and maximum threshold value is 9.0.
fwuRmtPwrDetectorBoardTraps	1.3.6.1.4.1.2014.15.2.1.2.9.2
NTF fwuRmtSystemVswrFault	1.3.6.1.4.1.2014.15.2.1.2.9.2.2			PRU/URU VSWR measurement above specification.
NTF fwuRmtRFPowerFault	1.3.6.1.4.1.2014.15.2.1.2.9.2.3			PRU/URU RF Output Power below minimum threshold.
fwuRmtLNAObjects	1.3.6.1.4.1.2014.15.2.1.2.10
fwuRmtLNAInfo	1.3.6.1.4.1.2014.15.2.1.2.10.1
fwuRmtLNAInfoTable	1.3.6.1.4.1.2014.15.2.1.2.10.1.1		not-accessible	This table maintains Information of remote LNA objects.
fwuRmtLNAInfoEntry	1.3.6.1.4.1.2014.15.2.1.2.10.1.1.1		not-accessible	Each entry in this table refers to LNA information.
I32 fwuRmtLNANumber	1.3.6.1.4.1.2014.15.2.1.2.10.1.1.1.1	Integer32	read-only	A unique identifier for LNA Objects.
LNA fwuRmtLNAType	1.3.6.1.4.1.2014.15.2.1.2.10.1.1.1.2	LNAType	read-only	Remote LNA card type. Valid LNA types are Cellular A(1), Cellular B(2), SMR Low(3), SMR High(4), PCS(5), AWS(6), SMR Low Wide(7), Full Cellular(8), GSM1800(9), UMTS(10), EGSM900(11), Lower ABC 700(12), Upper C 700(13), APAC 800 iDEN(14), Prism SMR 800 and 900(15), Prism SMR 900 and 800(16), Prism SMR 800(17).
STR fwuRmtLNARIADCPartNumber	1.3.6.1.4.1.2014.15.2.1.2.10.1.1.1.3	DisplayString	read-only	LNA Inventory Data - TE Part Number.
STR fwuRmtLNARISerialNumber	1.3.6.1.4.1.2014.15.2.1.2.10.1.1.1.4	DisplayString	read-only	LNA Inventory Data - Serial Number.
STR fwuRmtLNARIDateCode	1.3.6.1.4.1.2014.15.2.1.2.10.1.1.1.5	DisplayString	read-only	LNA Inventory Data - Date Code.
STR fwuRmtLNARIHWVer	1.3.6.1.4.1.2014.15.2.1.2.10.1.1.1.6	DisplayString	read-only	LNA Inventory Data - HW version.
DUP fwuRmtDuplexerType	1.3.6.1.4.1.2014.15.2.1.2.10.1.1.1.7	DuplexerType	read-only	Duplexer hardware type. Valid Duplexer Types are cellularA(1), cellularB(2), smrLow(3), smrHigh(4), pcs(5), aws(6), smrLowWide(7), fullCellular(8), gsm1800(9), umts(10), egsm900(11), lowerABC(12), upperC700(13), apac800iDEN(14), prismSmr800and900(15), prismSmr900and800(16), prismSmr800(17), cellularApac(18), apacEgsm900(19), pGsmEgsm900(20)
fwuRmtLNATraps	1.3.6.1.4.1.2014.15.2.1.2.10.2
NTF fwuRmtLNAPowerFault	1.3.6.1.4.1.2014.15.2.1.2.10.2.2			PRU/URU Low Noise Amplifier (LNA) Power fault.
NTF fwuRmtDuplexerFreqMismatchFault	1.3.6.1.4.1.2014.15.2.1.2.10.2.3			Configured frequency range not supported by Duplexer.
fwuRmtRDIObjects	1.3.6.1.4.1.2014.15.2.1.2.11
fwuRmtRDIInfo	1.3.6.1.4.1.2014.15.2.1.2.11.1
fwuRmtRDIInfoTable	1.3.6.1.4.1.2014.15.2.1.2.11.1.1		not-accessible	This table maintains Information of remote RDI objects.
fwuRmtRDIInfoEntry	1.3.6.1.4.1.2014.15.2.1.2.11.1.1.1		not-accessible	Each entry in this table refers to RDI information.
I32 fwuRmtRDINumber	1.3.6.1.4.1.2014.15.2.1.2.11.1.1.1.1	Integer32	read-only	A unique identifier for each RDI.
STR fwuRmtRDIRIADCPartNumber	1.3.6.1.4.1.2014.15.2.1.2.11.1.1.1.2	DisplayString	read-only	RDI Inventory Data - TE Part Number.
STR fwuRmtRDIRISerialNumber	1.3.6.1.4.1.2014.15.2.1.2.11.1.1.1.3	DisplayString	read-only	RDI Inventory Data - Serial Number.
STR fwuRmtRDIRIDateCode	1.3.6.1.4.1.2014.15.2.1.2.11.1.1.1.4	DisplayString	read-only	RDI Inventory Data - Date Code.
STR fwuRmtRDIRIHWVer	1.3.6.1.4.1.2014.15.2.1.2.11.1.1.1.5	DisplayString	read-only	RDI Inventory Data - HW version.
INT fwuRmtRDIRIHWType	1.3.6.1.4.1.2014.15.2.1.2.11.1.1.1.6	INTEGER	read-only	Identifies if RDI(1) or ALPACA(2) board. It may be unknown(0).
fwuRmtRDITraps	1.3.6.1.4.1.2014.15.2.1.2.11.2
NTF fwuRmtACPowerSupplyMon1Fault	1.3.6.1.4.1.2014.15.2.1.2.11.2.1			AC Power monitor 1 Fault.
NTF fwuRmtACPowerSupplyMon2Fault	1.3.6.1.4.1.2014.15.2.1.2.11.2.2			AC Power monitor 2 Fault.
NTF fwuRmtACPowerSupplyMon3Fault	1.3.6.1.4.1.2014.15.2.1.2.11.2.3			AC Power monitor 3 Fault.
fwuRmtRSIObjects	1.3.6.1.4.1.2014.15.2.1.2.12
fwuRmtRSIInfo	1.3.6.1.4.1.2014.15.2.1.2.12.1
fwuRmtRSIInfoTable	1.3.6.1.4.1.2014.15.2.1.2.12.1.1		not-accessible	This table maintains Information of Remote RSI objects.
fwuRmtRSIInfoEntry	1.3.6.1.4.1.2014.15.2.1.2.12.1.1.1		not-accessible	Each entry in this table refers to RSI information.
STR fwuRmtRSIRIADCPartNumber	1.3.6.1.4.1.2014.15.2.1.2.12.1.1.1.1	DisplayString	read-only	Remote Inventory Data - TE Part Number.
STR fwuRmtRSIRISerialNumber	1.3.6.1.4.1.2014.15.2.1.2.12.1.1.1.2	DisplayString	read-only	Remote Inventory Data - Serial Number.
STR fwuRmtRSIRIDateCode	1.3.6.1.4.1.2014.15.2.1.2.12.1.1.1.3	DisplayString	read-only	Remote Inventory Data - Date Code.
STR fwuRmtRSIRIHWVer	1.3.6.1.4.1.2014.15.2.1.2.12.1.1.1.4	DisplayString	read-only	Remote Inventory Data - Hardware version.
U32 fwuRmtCapacity	1.3.6.1.4.1.2014.15.2.1.2.12.1.1.1.5	Unsigned32	read-only	The number of RF modules that can be installed in the remote.
fwuRmtRSITraps	1.3.6.1.4.1.2014.15.2.1.2.12.2
NTF fwuRmtACPowerSupplyMon4Fault	1.3.6.1.4.1.2014.15.2.1.2.12.2.1			AC Power monitor 4 Fault.
fwuGeneralObjects	1.3.6.1.4.1.2014.15.2.1.3
fwuNotifObjects	1.3.6.1.4.1.2014.15.2.1.3.1
C32 fwuTrapSequenceNumber	1.3.6.1.4.1.2014.15.2.1.3.1.1	Counter32	accessible-for-notify	Count of the total number of traps (including this trap), raised by the agent.
DAT fwuTrapTimeStamp	1.3.6.1.4.1.2014.15.2.1.3.1.2	DateAndTime	accessible-for-notify	The trap time stamp.
ALA fwuNotificationStatus	1.3.6.1.4.1.2014.15.2.1.3.1.3	ALARMType	accessible-for-notify	The severity of the fault.
MOD fwuModuleType	1.3.6.1.4.1.2014.15.2.1.3.1.4	MODULEType	accessible-for-notify	The module type reporting alarm.
I32 fwuModuleNumber	1.3.6.1.4.1.2014.15.2.1.3.1.5	Integer32	accessible-for-notify	The numerical Id of module, for the above module type, reporting the alarm.
INT fwuTrapCode	1.3.6.1.4.1.2014.15.2.1.3.1.6	INTEGER	accessible-for-notify	The unique ID of the trap.
I32 fwuTrapNodeAddress	1.3.6.1.4.1.2014.15.2.1.3.1.7	Integer32	accessible-for-notify	Unit from which the trap originated.
STR fwuAlarmedModuleName	1.3.6.1.4.1.2014.15.2.1.3.1.8	DisplayString	accessible-for-notify	Name of the hardware module where the trap originated.
fwuDARTMappingObjects	1.3.6.1.4.1.2014.15.2.1.3.2
fwuDARTMappingInfo	1.3.6.1.4.1.2014.15.2.1.3.2.1
fwuDARTMappingTable	1.3.6.1.4.1.2014.15.2.1.3.2.1.1		not-accessible	This table maintains Information of DART Mapping Objects.
fwuDARTMappingEntry	1.3.6.1.4.1.2014.15.2.1.3.2.1.1.1		not-accessible	Each entry in this table refers to DART Mapping Objects.
U32 fwuDARTMappingIndex	1.3.6.1.4.1.2014.15.2.1.3.2.1.1.1.1	Unsigned32	read-only	DART Mapping Table Index.
UNI fwuUnitID	1.3.6.1.4.1.2014.15.2.1.3.2.1.1.1.2	UnitID2	read-create	Identifier for the unit.
I32 fwuUnitDARTID	1.3.6.1.4.1.2014.15.2.1.3.2.1.1.1.3	Integer32	read-create	Identifier of DART on the unit. Since there is a maximum of 8 DARTs, the valid values are one to eight.
I32 fwuUnitSFPID	1.3.6.1.4.1.2014.15.2.1.3.2.1.1.1.4	Integer32	read-create	Identifier of unit SFP connected to the mate DART (outgoing; away from the Host). Since there is a maximum of 8 SFPs, the valid values are one to eight.
OCT fwuUnitDartPassBand	1.3.6.1.4.1.2014.15.2.1.3.2.1.1.1.5	OCTET STRING	read-only	Band-Passband information of the linked DART on the host side.
UNI fwuMateID	1.3.6.1.4.1.2014.15.2.1.3.2.1.1.1.6	UnitID2	read-create	Identifier of (companion) mate unit.
I32 fwuMateDARTID	1.3.6.1.4.1.2014.15.2.1.3.2.1.1.1.7	Integer32	read-create	Identifies the (companion) DART on mate unit. Since there is a maximum of 8 DARTs, the valid values are one to eight.
I32 fwuMateSFPID	1.3.6.1.4.1.2014.15.2.1.3.2.1.1.1.8	Integer32	read-create	Identifies the remote SFP connected to the unit DART(incoming from direction of the Host).
OCT fwuMateDartPassband	1.3.6.1.4.1.2014.15.2.1.3.2.1.1.1.9	OCTET STRING	read-only	Band-Passband information of the linked DART on the Mate side.
I32 fwuSFPStartTimeSlot	1.3.6.1.4.1.2014.15.2.1.3.2.1.1.1.10	Integer32	read-create	Value of the first time slot used on the fiber carrying RF from unit DART to mate DART. Though this is a read-write object, the end user can only read the value. This and the next object are pair of values for a fiber. Depending on the DART type there may be a maximum of six or twelve time slots.
I32 fwuSFPEndTimeSlot	1.3.6.1.4.1.2014.15.2.1.3.2.1.1.1.11	Integer32	read-create	Value of the last time slot used on the fiber carrying RF from unit DART to mate DART. Though this is a read-write object, the end user can only read the value. This and the previous object are pair of values for a fiber.
ROW fwuMappingStatus	1.3.6.1.4.1.2014.15.2.1.3.2.1.1.1.12	RowStatus	read-create	The status of the conceptual row. The status may be active or inactive.
fwuSystemAlarmManagement	1.3.6.1.4.1.2014.15.2.1.3.3
fwuSystemAlarmManagementTable	1.3.6.1.4.1.2014.15.2.1.3.3.1		not-accessible	This table maintains alarm managing property and threshold information of all alarms.
fwuSystemAlarmManagementEntry	1.3.6.1.4.1.2014.15.2.1.3.3.1.1		not-accessible	Each entry in this table refers to Alarm management table Objects.
U32 fwuSYstemAlarmCode	1.3.6.1.4.1.2014.15.2.1.3.3.1.1.1	Unsigned32	read-only	The alarm code.It is used as Table Index.
ALA fwuSystemAlarmManageable	1.3.6.1.4.1.2014.15.2.1.3.3.1.1.2	ALARMManage	read-only	Indicates if the alarm is manageble(0) or not (1). If manageable, use fwuSystemAlarmEnabled, see below, to enable or disable the alarm.
STR fwuSystemAlarmThreshold	1.3.6.1.4.1.2014.15.2.1.3.3.1.1.3	DisplayString	read-only	Alarm Threshold value.
I32 fwuSystemAlarmModType	1.3.6.1.4.1.2014.15.2.1.3.3.1.1.4	Integer32	read-only	Identifies the module type which raised the alarm.
fwuSystemModuleAlarmEnableTable	1.3.6.1.4.1.2014.15.2.1.3.3.2		not-accessible	This table will allow the user to enable or disable an alarm. Use the fwuSystemAlarmManagementTable to check if the alarm is manageable or not.
fwuSystemModuleAlarmEnableEntry	1.3.6.1.4.1.2014.15.2.1.3.3.2.1		not-accessible	Each entry in this table refers to Module alarm enable table Objects.
U32 fwuSystemTrapNodeAddress	1.3.6.1.4.1.2014.15.2.1.3.3.2.1.1	Unsigned32	read-write	The unit which raised the alarm.
U32 fwuSystemAlarmModuleNo	1.3.6.1.4.1.2014.15.2.1.3.3.2.1.2	Unsigned32	read-write	The module which raised the alarm.
U32 fwuSystemModuleAlarmcode	1.3.6.1.4.1.2014.15.2.1.3.3.2.1.3	Unsigned32	read-write	The alarm code.
ALA fwuSystemAlarmEnabled	1.3.6.1.4.1.2014.15.2.1.3.3.2.1.4	ALARMEnable	read-write	This is used to enable or disable the alarm. Alarms is enabled by default, except the Uplink inactivity fault.
fwuGeoObjects	1.3.6.1.4.1.2014.15.2.1.3.4
fwuGeoTable	1.3.6.1.4.1.2014.15.2.1.3.4.2		not-accessible	This table maintains Information of Geo Objects.
fwuGeoEntry	1.3.6.1.4.1.2014.15.2.1.3.4.2.1		not-accessible	Each entry in this table refers to Geo Objects.
U32 fwuGeoIndex	1.3.6.1.4.1.2014.15.2.1.3.4.2.1.1	Unsigned32	read-write	Geo objects Table Index.
STR fwuGeoLatitude	1.3.6.1.4.1.2014.15.2.1.3.4.2.1.2	DisplayString	read-write	Identifies the Latitude of remote unit.
STR fwuGeoLongitude	1.3.6.1.4.1.2014.15.2.1.3.4.2.1.3	DisplayString	read-write	Identifies the Longitude of remote unit.
STR fwuGeoRmtName	1.3.6.1.4.1.2014.15.2.1.3.4.2.1.4	DisplayString	read-only	The Remote name.
INT fwuGeoStatus	1.3.6.1.4.1.2014.15.2.1.3.4.2.1.5	INTEGER	read-only	Standard SNMP row status for this table.
fwuSnmpSettings	1.3.6.1.4.1.2014.15.2.1.3.5
INT fwuV1TrapAgentAddrOverrideMode	1.3.6.1.4.1.2014.15.2.1.3.5.1	INTEGER	read-write	Provision to overide the default (1) or use default (0) agent address in v1 trap PDU. Use fwuV1TrapAgentAddrOverrideIPAddr to set the overriding agent address.
OCT fwuV1TrapAgentAddrOverrideIPAddr	1.3.6.1.4.1.2014.15.2.1.3.5.2	OCTET STRING	read-write	The overriding agent IP address in v1 trap PDU. Use Internet standard dot-decimal notation. Enable its use by setting fwuV1TrapAgentAddrOverrideMode.
I32 fwuSnmpTrapResendInterval	1.3.6.1.4.1.2014.15.2.1.3.5.3	Integer32	read-write	Time, in seconds, to resend unacknowledged traps. The trap will not be resent if this is set to zero(0). Acknowledgement is not needed if resend is not required, therefore, no trap entry will be entered into fwuSystemActiveAlarmTable.
I32 fwuSnmpTrapResendMaximum	1.3.6.1.4.1.2014.15.2.1.3.5.4	Integer32	read-write	Maximum number of times traps will be resent before removal if not acknowledged. If set to zero, it will not be resent.
fwuSnmpTrapMgrConfigTable	1.3.6.1.4.1.2014.15.2.1.3.5.7		not-accessible	Table containing information about the trap destinations. For changes to take effect, a (Host) reboot is required.
fwuSnmpTrapMgrConfigEntry	1.3.6.1.4.1.2014.15.2.1.3.5.7.1		not-accessible	An entry in the fwuSnmpTrapMgrConfigTable.
INT fwuTrapMgrRowId	1.3.6.1.4.1.2014.15.2.1.3.5.7.1.1	INTEGER	not-accessible	The unique index of this trap destination.
OCT fwuTrapMgrIpAddress	1.3.6.1.4.1.2014.15.2.1.3.5.7.1.2	OCTET STRING	read-create	Provision to set the IP address of the trap manager. Use Internet standard dot-decimal notation.
U32 fwuTrapMgrListeningPort	1.3.6.1.4.1.2014.15.2.1.3.5.7.1.3	Unsigned32	read-create	Provision to set the port at which the trap manager is listening for the traps. The default port for SNMP traps is 162.
STR fwuTrapMgrCommunity	1.3.6.1.4.1.2014.15.2.1.3.5.7.1.4	DisplayString	read-create	The community used by the agent to send traps or informs to this manager.
INT fwuTrapVersion	1.3.6.1.4.1.2014.15.2.1.3.5.7.1.5	INTEGER	read-create	The SNMP version used for this trap destination. The available versions are v1(0), v2c(1), inform(2) with v2c being set as default.
ROW fwuTrapMgrRowStatus	1.3.6.1.4.1.2014.15.2.1.3.5.7.1.6	RowStatus	read-create	The status of this conceptual row. This is used to manage the creation and deletion of this trap destination table.
INT fwuEnableNotifHysteresis	1.3.6.1.4.1.2014.15.2.1.3.5.8	INTEGER	read-write	Provision to enable(1) or disable(0) event hysteresis. If disabled notification is sent out on occurance of the event. If enabled set the hysteresis value using fwuEventNotifHysteresis.
I32 fwuEventNotifHysteresis	1.3.6.1.4.1.2014.15.2.1.3.5.9	Integer32	read-write	Time period, in seconds, for which an event has to persist before a notification is sent. For this value to be useable, ensure that fwuEnableNotifHysteresis is enabled.
INT fwuEnableNotifInterval	1.3.6.1.4.1.2014.15.2.1.3.5.10	INTEGER	read-write	Provision to enable(1) or disable(0) a time lag before sending out an event notification. If disabled, notification is sent out on the occurance of the event. If enabled, use fwuEventNotifInterval to set the lag.
I32 fwuEventNotifInterval	1.3.6.1.4.1.2014.15.2.1.3.5.11	Integer32	read-write	Provision to set the time lag in seconds between the successive event notifications. For this value to be useable, ensure that fwuEnableNotifInterval is enabled.
fwuSchedulerTable	1.3.6.1.4.1.2014.15.2.1.3.5.12		not-accessible	Table containing information about the trap destinations. For changes to take effect, a (Host) reboot is required.
fwuSchedulerEntry	1.3.6.1.4.1.2014.15.2.1.3.5.12.1		not-accessible	An entry in the fwuSchedulerTable.
INT fwuTaskId	1.3.6.1.4.1.2014.15.2.1.3.5.12.1.1	INTEGER	not-accessible	The unique index of the Scheduler table. Range limited to machine integer size(32 bit) restriction.
INT fwuTaskType	1.3.6.1.4.1.2014.15.2.1.3.5.12.1.2	INTEGER	read-create	The task to be scheduled. If System Test is the task being scheduled it requires some more arguments. Use fwuFunctionArgs to provide them. After specifying a task, enable the task using fwuScheduleStatus.
INT fwuScheduleStatus	1.3.6.1.4.1.2014.15.2.1.3.5.12.1.3	INTEGER	read-create	Provision to enable(1) or disable(0) the scheduled task (defined by fwuTaskType).
STR fwuTaskStartTime	1.3.6.1.4.1.2014.15.2.1.3.5.12.1.4	DisplayString	read-create	The start time of the scheduled activity.
INT fwuOccurrences	1.3.6.1.4.1.2014.15.2.1.3.5.12.1.5	INTEGER	read-create	Provision to set the number of times the task is to be executed. Set a value greater than 0 for a finite number of executions. To keep executing forever, set value to -1.
STR fwuRecurrence	1.3.6.1.4.1.2014.15.2.1.3.5.12.1.6	DisplayString	read-create	Provision to set the periodicity of the scheduled task. Eg. S5 is 5 Sec, H6 is 6 Hours, M8 is 8 Min. Note: This is also used for the time interval for sending I am alive traps.
STR fwuFunctionArgs	1.3.6.1.4.1.2014.15.2.1.3.5.12.1.7	DisplayString	read-create	Colon separated string of arguments required for the given task type. Can be empty depending on the task type.
ROW fwuRowStatus	1.3.6.1.4.1.2014.15.2.1.3.5.12.1.8	RowStatus	read-create	The status of the conceptual row. This is used to manage the creation and deletion of the rows in scheduler table.
fwuContactAlarmObjects	1.3.6.1.4.1.2014.15.2.1.3.6
fwuContactAlarmInfo	1.3.6.1.4.1.2014.15.2.1.3.6.1
fwuSystemContactAlarmMgmtTable	1.3.6.1.4.1.2014.15.2.1.3.6.1.1		not-accessible	Entities in this table are applicable to all Prism and URH remote units. For Host and DRU, entities are applicable only for 2nd generation system cards and onwards.
fwuSystemContactAlarmMgmtEntry	1.3.6.1.4.1.2014.15.2.1.3.6.1.1.1		not-accessible	An entry (conceptual row) in the fwuSnmpTrapMgrConfigTable.
UNI fwuUnitIndex	1.3.6.1.4.1.2014.15.2.1.3.6.1.1.1.1	UnitID2	read-only	The number of the connected unit.
STR fwuContactAlarm	1.3.6.1.4.1.2014.15.2.1.3.6.1.1.1.3	DisplayString	read-only	Hardware Assigned Name.
INT fwuContactAlarmMode	1.3.6.1.4.1.2014.15.2.1.3.6.1.1.1.4	INTEGER	read-write	Provision to set the mode of the alarm as normally closed (1) or normally open (2).
STR fwuContactAlarmName	1.3.6.1.4.1.2014.15.2.1.3.6.1.1.1.5	DisplayString	read-write	User defined name of the host unit. All characters except angular brackets, single and double quotes are allowed. Minimum length of the name is 0 character (It may be empty.). Maximum length of the name is 64 characters.
ALA fwuContactAlarmEnable	1.3.6.1.4.1.2014.15.2.1.3.6.1.1.1.6	ALARMEnable	read-write	Provision to enable (1) or disable (0) the contact alarm. The alarm is enabled by default.
INT fwuContactAlarmSeverity	1.3.6.1.4.1.2014.15.2.1.3.6.1.1.1.7	INTEGER	read-write	Severity of the alarm.
fwuContactAlarmTraps	1.3.6.1.4.1.2014.15.2.1.3.6.2
NTF fwuHstContactAlarmOutput1	1.3.6.1.4.1.2014.15.2.1.3.6.2.1			Host contact output port state.
NTF fwuHstContactAlarmOutput2	1.3.6.1.4.1.2014.15.2.1.3.6.2.2			Host contact output port state.
NTF fwuHstContactAlarmInput1	1.3.6.1.4.1.2014.15.2.1.3.6.2.3			Host contact input port state.
NTF fwuHstContactAlarmInput2	1.3.6.1.4.1.2014.15.2.1.3.6.2.4			Host contact input port state.
NTF fwuRmtContactAlarmInput1	1.3.6.1.4.1.2014.15.2.1.3.6.2.5			Remote contact input port state- Summary of all connected remotes.
NTF fwuRmtContactAlarmInput2	1.3.6.1.4.1.2014.15.2.1.3.6.2.6			Remote contact input port state- Summary of all connected remotes.
NTF fwuRmtContactAlarmOutput1	1.3.6.1.4.1.2014.15.2.1.3.6.2.7			Remote contact output port state- Summary of all connected remotes.
NTF fwuRmtContactAlarmOutput2	1.3.6.1.4.1.2014.15.2.1.3.6.2.8			Remote contact output port state- Summary of all connected remotes.
fwuSystemStaticAlarms	1.3.6.1.4.1.2014.15.2.1.3.7
fwuSystemStaticAlarmsTable	1.3.6.1.4.1.2014.15.2.1.3.7.1		not-accessible	This is a static alarm table containing the statistics of units in the system. The major and minor alarms will be grouped separately for each of the units.
fwuSystemStaticAlarmsEntry	1.3.6.1.4.1.2014.15.2.1.3.7.1.1		not-accessible	Entries for units which can be either alarmed or not alarmed or not-discovered.
UNI fwuSystemUnitID	1.3.6.1.4.1.2014.15.2.1.3.7.1.1.1	UnitID2	read-only	The ID of the unit from which the alarms has been raised.
UNI fwuSystemUnitType	1.3.6.1.4.1.2014.15.2.1.3.7.1.1.2	UnitType	read-only	The type of the from which the alarm has been raised.
STR fwuUnitMajorAlarms	1.3.6.1.4.1.2014.15.2.1.3.7.1.1.3	DisplayString	read-only	The major alarm name of the unit.
STR fwuUnitMinorAlarms	1.3.6.1.4.1.2014.15.2.1.3.7.1.1.4	DisplayString	read-only	The minor alarm name of the unit.
flexwaveurhMIBConformance	1.3.6.1.4.1.2014.15.2.1.4
flexwaveurhMIBCompliances	1.3.6.1.4.1.2014.15.2.1.4.1
flexwaveurhBasicCompliance	1.3.6.1.4.1.2014.15.2.1.4.1.1			The compliance statement for Flexwave entities which implement the ADC-FLEXWAVE-URH-MIB.
flexwaveurhMIBGroups	1.3.6.1.4.1.2014.15.2.1.4.2
fwuSerfGroup	1.3.6.1.4.1.2014.15.2.1.4.2.1			A collection of Host and Remote SERF objects.
fwuOpticsGroup	1.3.6.1.4.1.2014.15.2.1.4.2.2			A collection of Host and Remote Optical and Ethernet port objects.
fwuDartGroup	1.3.6.1.4.1.2014.15.2.1.4.2.3			A collection of Host and Remote DART objects.
fwuLnaGroup	1.3.6.1.4.1.2014.15.2.1.4.2.4			A collection of Host and Remote LNA objects.
fwuLpaGroup	1.3.6.1.4.1.2014.15.2.1.4.2.5			A collection of Host and Remote LPA objects.
fwuDuplexerGroup	1.3.6.1.4.1.2014.15.2.1.4.2.6			A collection of Host and Remote Duplexer objects.
fwuAlarmConfigGroup	1.3.6.1.4.1.2014.15.2.1.4.2.7			A collection of Host and Remote Alarm configuration objects.
fwuNotificationGroup	1.3.6.1.4.1.2014.15.2.1.4.2.8			A collection of Host and Remote Notification objects.
fwuLinkingGroup	1.3.6.1.4.1.2014.15.2.1.4.2.9			A collection of RF linking configuration objects.
fwuMateInfoGroup	1.3.6.1.4.1.2014.15.2.1.4.2.10			A collection of mate information objects.
fwuSprintModeGroup	1.3.6.1.4.1.2014.15.2.1.4.2.11			A collection of objects supported in Sprint mode Objects.
fwuSNMPSettingGroup	1.3.6.1.4.1.2014.15.2.1.4.2.12			A collection of objects supported in System Link test.
fwuSystemStaticAlarmsGroup	1.3.6.1.4.1.2014.15.2.1.4.2.13			A collection of objects supported in Static Alarms Table.

RFC description

Manages TE Connectivity FlexWave Prism and InterReach SPECTRUM radio frequency products for version 8.1 and later.

Start monitoring ADC/TE FlexWave DAS remote radio units with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ADC-FLEXWAVE-URH-MIB