All MIBs › TELDAT-MON-INTERF-PPP-MIB
Category: Remote Access and Serial WAN, Teldat Router Management
Description: Monitors Teldat router PPP interface negotiation state, LCP/NCP status, and per-protocol traffic counters.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is TELDAT-MON-INTERF-PPP-MIB?
This is a Teldat vendor MIB for monitoring PPP (Point-to-Point Protocol) WAN interfaces on Teldat routers, covering link negotiation state, LCP (Link Control Protocol) and NCP (Network Control Protocol) phase status, and per-protocol traffic counters. It exposes operational status data describing whether a PPP link has successfully completed LCP/NCP negotiation and traffic statistics broken down by the network-layer protocol running over the PPP link (e.g., IP, IPX). It is heavily monitoring-oriented for software/protocol-layer status — the LCP/NCP negotiation state directly reveals whether a WAN link is up and usable versus stuck in negotiation due to a misconfiguration or peer mismatch, which is a common root cause of "interface up but no traffic" WAN outages. It likely complements the standard IETF PPP-MIB (RFC 1471/1473) by adding Teldat-specific detail, though no sample objects were available to confirm this directly. It is typically deployed on Teldat routers at branch or WAN aggregation sites where PPP-encapsulated leased lines or serial links need close monitoring of negotiation health, which the TELDAT-MON-INTERF-PPP-MIB MIB is designed to expose.
IPNetwork Monitor allows you to monitor SNMP objects defined in TELDAT-MON-INTERF-PPP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Teldat router (WAN/branch)
Monitoring Examples
No object/table names were extracted for this MIB in the provided data, so a concrete polling example using real object names cannot be given; in principle an administrator would poll per-interface LCP/NCP state objects to confirm a PPP link has fully negotiated and check per-protocol traffic counters to detect a link that is up but passing no traffic for a given upper-layer protocol.
This MIB depends on
Related MIBs
Imported Objects
From RFC-1212
| OBJECT-TYPE |
From RFC1155-SMI
| Counter | |
| IpAddress |
From RFC1213-MIB
| DisplayString | |
| PhysAddress |
| telProdNpMonInterfRouter | OBJECT-IDENTITY |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| telProdNpMonInterfPPP | 1.3.6.1.4.1.2007.4.1.2.2.2.10 | |||
| telProdNpMonIfcPPPLCPGroup | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1 | |||
| telProdNpMonIfcPPPLCPControlGloTable | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.1 | not-accessible | This table contains global LCP parameters. The entry number is determined by the PPP interface number, the lower interface number and the order number of the link inside the lower interface. | |
| telProdNpMonIfcPPPLCPControlGloEntry | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.1.1 | not-accessible | Each entry contains the PPP interface number of the node, the lower interface number, the order number of the link inside the lower interface, a description of the lower interface, the circuit identifier, the version number and the current state of the LCP protocol. | |
| INT telProdNpMonIfcPPPLCPCtrlGloPPPIndex | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.1.1.1 | INTEGER | read-only | PPP interface number of the node (first index of the entry). |
| INT telProdNpMonIfcPPPLCPCtrlGloLowIndex | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.1.1.2 | INTEGER | read-only | Lower interface number of the node (second index of the entry). |
| INT telProdNpMonIfcPPPLCPCtrlGloOrdIndex | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.1.1.3 | INTEGER | read-only | Order number of the link inside the lower interface corresponding to the LCP parameters of the entry (third index of the entry). |
| STR telProdNpMonIfcPPPLCPCtrlGloLowDescr | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.1.1.4 | DisplayString | read-only | A description of the lower interface corresponding to this entry. |
| INT telProdNpMonIfcPPPLCPCtrlGloCircId | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.1.1.5 | INTEGER | read-only | Circuit identifier inside the lower interface. |
| STR telProdNpMonIfcPPPLCPCtrlGloVersion | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.1.1.6 | DisplayString | read-only | Version number. |
| INT telProdNpMonIfcPPPLCPCtrlGloState | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.1.1.7 | INTEGER | read-only | Current protocol state. The possible values of the variable are integer numbers between 0 and 9. Each number is related to a feasible state: (0) initial, (1) starting, (2) closed, (3) stopped, (4) closing, (5) stopping, (6) req-sent, (7) ack-rcvd, (8) ack-sent, (9) opened. |
| telProdNpMonIfcPPPLCPControlOptionsTable | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.2 | not-accessible | This table contains variables that give information about the transmitted and received options during the link setup. The entry number is determined by the PPP interface number, the lower interface number and the order number of the link inside the lower interface. | |
| telProdNpMonIfcPPPLCPControlOptionsEntry | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.2.1 | not-accessible | Each entry contains the PPP interface number, the lower interface number, the order number of the link inside the lower interface, a description of the lower interface, the circuit identifier, the local and remote MRU, the local and remote Asynchronous Control Character Map, the authentication type (if it exists) in the local and remote site, the local and remote Magic Number, if Protocol Field Compression has been used in the local or remote end, if Address/Control Field Compression has been used in the local or remote end, and if 32 bits Checksum has been used in the local or remote end. | |
| INT telProdNpMonIfcPPPLCPCtrlOptPPPIndex | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.2.1.1 | INTEGER | read-only | PPP interface number of the node (first index of the entry). |
| INT telProdNpMonIfcPPPLCPCtrlOptLowIndex | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.2.1.2 | INTEGER | read-only | Lower interface number of the node (second index of the entry). |
| INT telProdNpMonIfcPPPLCPCtrlOptOrdIndex | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.2.1.3 | INTEGER | read-only | Order number of the link inside the lower interface corresponding to the LCP parameters of the entry (third index of the entry). |
| STR telProdNpMonIfcPPPLCPCtrlOptLowDescr | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.2.1.4 | DisplayString | read-only | A description of the lower interface corresponding to this entry. |
| INT telProdNpMonIfcPPPLCPCtrlOptCircId | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.2.1.5 | INTEGER | read-only | Circuit identifier inside the lower interface. |
| INT telProdNpMonIfcPPPLCPCtrlOptMRULoc | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.2.1.6 | INTEGER | read-only | MRU (Maximum Received Unit) in the local end. It represents the PPP frame maximum size that is accepted in reception. |
| INT telProdNpMonIfcPPPLCPCtrlOptMRURem | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.2.1.7 | INTEGER | read-only | MRU (Maximum Received Unit) in the remote end. It represents the PPP frame maximum size that is accepted in reception. |
| OCT telProdNpMonIfcPPPLCPCtrlOptAsyCharMaskLoc | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.2.1.8 | OCTET STRING | read-only | Local Asynchronous Control Character Map. It shows the mask to use if transparent transmission is applied over control characters (XON, XOFF) for asynchronous PPP. If characters are inside the frame, they won't cause the activation of flow control process in modems or adapters. |
| OCT telProdNpMonIfcPPPLCPCtrlOptAsyCharMaskRem | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.2.1.9 | OCTET STRING | read-only | Remote Asynchronous Control Character Map. It shows the mask to use if transparent transmission is applied over control characters (XON, XOFF) for asynchronous PPP. If characters are inside the frame, they won't cause the activation of flow control process in modems or adapters. |
| INT telProdNpMonIfcPPPLCPCtrlOptAuthLoc | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.2.1.10 | INTEGER | read-only | Local authentication type used. Possible options are: PAP (1), CHAP (2), a different one (3) or no authentication used (0). |
| INT telProdNpMonIfcPPPLCPCtrlOptAuthRem | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.2.1.11 | INTEGER | read-only | Remote authentication type used. Possible options are: PAP (1), CHAP (2), a different one (3) or no authentication used (0). |
| STR telProdNpMonIfcPPPLCPCtrlOptMagNumLoc | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.2.1.12 | DisplayString | read-only | Local magic number. It is useful to determine if there is a loop in the link by transmitting a random number between the ends based on the system clock and the times the clock has reset. The magic number has 4 bytes. This variable is a string that shows an hexadecimal value. |
| STR telProdNpMonIfcPPPLCPCtrlOptMagNumRem | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.2.1.13 | DisplayString | read-only | Remote magic number. It is useful to determine if there is a loop in the link by transmitting a random number between the ends based on the system clock and the times the clock has reset. The magic number has 4 bytes. This variable is a string that shows an hexadecimal value. |
| INT telProdNpMonIfcPPPLCPCtrlOptProtCmpLoc | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.2.1.14 | INTEGER | read-only | This variable indicates if Protocol Field Compression is used at the local end. Possible values are: (1) yes or (2) no. Once LCP has been negotiated and NCP has been established, the PPP frame protocol field is compressed and a byte is transmitted. |
| INT telProdNpMonIfcPPPLCPCtrlOptProtCmpRem | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.2.1.15 | INTEGER | read-only | This variable indicates if Protocol Field Compression is used at the remote end. Possible values are: (0) non negotiated, (1) yes or (2) no. Once LCP has been negotiated and NCP has been established, the PPP frame protocol field is compressed and a byte is transmitted. |
| INT telProdNpMonIfcPPPLCPCtrlOptAddCmpLoc | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.2.1.16 | INTEGER | read-only | This variable indicates if Address/Control Field Compression is used at the local end. Possible values are: (1) yes or (2) no. Once LCP has been negotiated and NCP has been established, the control and address fields of the PPP frame are not transmitted. |
| INT telProdNpMonIfcPPPLCPCtrlOptAddCmpRem | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.2.1.17 | INTEGER | read-only | This variable indicates if Address/Control Field Compression is used at the remote end. Possible values are: (0) non negotiated, (1) yes or (2) no. Once LCP has been negotiated and NCP has been established, the control and address fields of the PPP frame are not transmitted. |
| INT telProdNpMonIfcPPPLCPCtrlOptChecksumLoc | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.2.1.18 | INTEGER | read-only | This variable indicates if 32 bits Checksum is used at the local end. Possible values are: (1) yes or (2) no. |
| INT telProdNpMonIfcPPPLCPCtrlOptChecksumRem | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.2.1.19 | INTEGER | read-only | This variable indicates if 32 bits Checksum is used at the remote end. Possible values are: (1) yes or (2) no. |
| telProdNpMonIfcPPPLCPStatsTable | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.3 | not-accessible | This table contains statistics of the LCP protocol. The entry number is determined by the PPP interface number, the lower interface number and the order number of the link inside the lower interface. | |
| telProdNpMonIfcPPPLCPStatsEntry | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.3.1 | not-accessible | Each entry contains the PPP interface number, the lower interface number, the order number of the link inside the lower interface, a description of the lower interface, the circuit identifier, a variable to check variables deletion (corresponding counters reset), and variables that give information about the following counters values: sent and received frames number, sent and received bytes number, number of sent and received Configure Request LCP frames, number of sent and received Configure Ack LCP frames, number of sent and received Configure Nak LCP frames, number of sent and received Configure Reject LCP frames, number of sent and received Terminate Request LCP frames, number of sent and received Terminate Ack LCP frames, number of sent and received Echo Request LCP frames, number of sent and received Echo Reply LCP frames. | |
| INT telProdNpMonIfcPPPLCPStPPPIndex | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.3.1.1 | INTEGER | read-only | PPP interface number of the node (first index of the entry). |
| INT telProdNpMonIfcPPPLCPStLowIndex | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.3.1.2 | INTEGER | read-only | Lower interface number of the node (second index of the entry). |
| INT telProdNpMonIfcPPPLCPStOrdIndex | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.3.1.3 | INTEGER | read-only | Order number of the link inside the lower interface corresponding to the LCP parameters of the entry (third index of the entry). |
| STR telProdNpMonIfcPPPLCPStLowDescr | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.3.1.4 | DisplayString | read-only | A description of the lower interface corresponding to this entry. |
| INT telProdNpMonIfcPPPLCPStCircId | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.3.1.5 | INTEGER | read-only | Circuit identifier inside the lower interface. |
| INT telProdNpMonIfcPPPLCPStClear | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.3.1.6 | INTEGER | read-write | This variable when is readed shows the output from the last counter restart attempt: the value is 2 (ok) if the restart was performed succesfully, 3 (error) if an error ocurred and 4 (undefined) if nobody has tried to restart the counters yet. In set operations, the value 1 (it is the only value that can be assigned by a writing operation) causes a counter restart. |
| CTR telProdNpMonIfcPPPLCPStFramesRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.3.1.7 | Counter | read-only | Number of frames received through the link shown in the indexes. |
| CTR telProdNpMonIfcPPPLCPStFramesTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.3.1.8 | Counter | read-only | Number of frames sent through the link shown in the indexes. |
| CTR telProdNpMonIfcPPPLCPStBytesRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.3.1.9 | Counter | read-only | Number of bytes received through the link shown in the indexes. |
| CTR telProdNpMonIfcPPPLCPStBytesTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.3.1.10 | Counter | read-only | Number of bytes sent through the link shown in the indexes. |
| CTR telProdNpMonIfcPPPLCPStConfReqRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.3.1.11 | Counter | read-only | Number of Configure Request LCP frames received through the link shown in the indexes. These frames are transmitted when a link is started and contains link configuration options. |
| CTR telProdNpMonIfcPPPLCPStConfReqTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.3.1.12 | Counter | read-only | Number of Configure Request LCP frames sent through the link shown in the indexes. These frames are transmitted when a link is started and contains link configuration options. |
| CTR telProdNpMonIfcPPPLCPStConfAckRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.3.1.13 | Counter | read-only | Number of Configure Ack LCP frames received through the link shown in the indexes. These frames are answers to Configure Requests and shows accordance with the received configuration options. |
| CTR telProdNpMonIfcPPPLCPStConfAckTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.3.1.14 | Counter | read-only | Number of Configure Ack LCP frames transmitted through the link shown in the indexes. These frames are answers to Configure Requests and shows accordance with the received configuration options. |
| CTR telProdNpMonIfcPPPLCPStConfNakRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.3.1.15 | Counter | read-only | Number of Configure Nak LCP frames received through the link shown in the indexes. These frames are answers to Configure Requests and indicates that some configuration options received in the identified frame has not been accepted, nevertheless a remote reccomended or accepted value is sent. |
| CTR telProdNpMonIfcPPPLCPStConfNakTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.3.1.16 | Counter | read-only | Number of Configure Nak LCP frames transmitted through the link shown in the indexes. These frames are answers to Configure Requests and indicates that some configuration options received in the identified frame has not been accepted, nevertheless a remote reccomended or accepted value is sent. |
| CTR telProdNpMonIfcPPPLCPStConfRejRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.3.1.17 | Counter | read-only | Number of Configure Reject LCP frames received through the link shown in the indexes. These frames are answers to Configure Requests and indicates that some configuration options received in the identified frame has not neither accepted nor recognized. |
| CTR telProdNpMonIfcPPPLCPStConfRejTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.3.1.18 | Counter | read-only | Number of Configure Reject LCP frames transmitted through the link shown in the indexes. These frames are answers to Configure Requests and indicates that some configuration options received in the identified frame has not neither accepted nor recognized. |
| CTR telProdNpMonIfcPPPLCPStTermReqRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.3.1.19 | Counter | read-only | Number of Terminate Request LCP frames received through the link shown in the indexes. These frames are transmitted to finish, close, the link. |
| CTR telProdNpMonIfcPPPLCPStTermReqTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.3.1.20 | Counter | read-only | Number of Terminate Request LCP frames transmitted through the link shown in the indexes. These frames are transmitted to finish, close, the link. |
| CTR telProdNpMonIfcPPPLCPStTermAckRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.3.1.21 | Counter | read-only | Number of Terminate Ack LCP frames received through the link shown in the indexes. These frames are transmitted after a Terminate Request is received. The reception of a non expected Terminate Ack packet indicates that the link has been closed. |
| CTR telProdNpMonIfcPPPLCPStTermAckTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.3.1.22 | Counter | read-only | Number of Terminate Ack LCP frames transmitted through the link shown in the indexes. These frames are transmitted after a Terminate Request is received. The reception of a non expected Terminate Ack packet indicates that the link has been closed. |
| CTR telProdNpMonIfcPPPLCPStEchoReqRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.3.1.23 | Counter | read-only | Number of Echo Request LCP frames received through the link shown in the indexes. These frames are used in link maintenance. From time to time a query containing Echo Request code is generated, and is sent back with an Echo Reply. |
| CTR telProdNpMonIfcPPPLCPStEchoReqTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.3.1.24 | Counter | read-only | Number of Echo Request LCP frames transmitted through the link shown in the indexes. These frames are used in link maintenance. From time to time a query containing Echo Request code is generated, and is sent back with an Echo Reply. |
| CTR telProdNpMonIfcPPPLCPStEchoRepRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.3.1.25 | Counter | read-only | Number of Echo Reply LCP frames received through the link shown in the indexes. These frames are used in link maintenance. From time to time a query containing Echo Request code is generated, and is sent back with an Echo Reply. |
| CTR telProdNpMonIfcPPPLCPStEchoRepTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.1.3.1.26 | Counter | read-only | Number of Echo Reply LCP frames transmitted through the link shown in the indexes. These frames are used in link maintenance. From time to time a query containing Echo Request code is generated, and is sent back with an Echo Reply. |
| telProdNpMonIfcPPPIPCPGroup | 1.3.6.1.4.1.2007.4.1.2.2.2.10.2 | |||
| telProdNpMonIfcPPPIPCPControlGloTable | 1.3.6.1.4.1.2007.4.1.2.2.2.10.2.1 | not-accessible | This table contains IPCP global parameters. This table has an entry for each PPP interface of the node. The entry number is determined by the corresponding interface number (table index). | |
| telProdNpMonIfcPPPIPCPControlGloEntry | 1.3.6.1.4.1.2007.4.1.2.2.2.10.2.1.1 | not-accessible | Each entry contains the node interface number which is the table index, and a variable that shows the current state of the IPCP protocol. | |
| INT telProdNpMonIfcPPPIPCPCtrlGloIndex | 1.3.6.1.4.1.2007.4.1.2.2.2.10.2.1.1.1 | INTEGER | read-only | Interface number of the node, that indicates the corresponding table entry (it is the table index). |
| INT telProdNpMonIfcPPPIPCPCtrlGloState | 1.3.6.1.4.1.2007.4.1.2.2.2.10.2.1.1.2 | INTEGER | read-only | Current protocol state. The possible values of the variable are integer numbers between 0 and 9. Each number is related to a feasible state: (0) initial, (1) starting, (2) closed, (3) stopped, (4) closing, (5) stopping, (6) req-sent, (7) ack-rcvd, (8) ack-sent, (9) opened. |
| telProdNpMonIfcPPPIPCPControlOptionsTable | 1.3.6.1.4.1.2007.4.1.2.2.2.10.2.2 | not-accessible | This table contains information about parameters used to monitor received and transmitted options during the network level protocol setup. The entry number is determined by the interface value (table index). | |
| telProdNpMonIfcPPPIPCPControlOptionsEntry | 1.3.6.1.4.1.2007.4.1.2.2.2.10.2.2.1 | not-accessible | Each entry contains the node interface number, which is the table index, the assigned IP address (in case of dinamic asignation), remote end IP address (if received) and if the Van Jacobson compression option has been selected at any end (local or remote). | |
| INT telProdNpMonIfcPPPIPCPCtrlOptIndex | 1.3.6.1.4.1.2007.4.1.2.2.2.10.2.2.1.1 | INTEGER | read-only | Interface number of the node, that indicates the corresponding table entry (it is the table index). |
| IP telProdNpMonIfcPPPIPCPCtrlOptIpAddrLoc | 1.3.6.1.4.1.2007.4.1.2.2.2.10.2.2.1.2 | IpAddress | read-only | The IP address assigned (supposing dinamic assignation has been selected). |
| IP telProdNpMonIfcPPPIPCPCtrlOptIpAddrRem | 1.3.6.1.4.1.2007.4.1.2.2.2.10.2.2.1.3 | IpAddress | read-only | The remote IP address (supposing it has been received). |
| INT telProdNpMonIfcPPPIPCPCtrlOptVJCmpLoc | 1.3.6.1.4.1.2007.4.1.2.2.2.10.2.2.1.4 | INTEGER | read-only | Van Jacobson compression selected or not in the local end: (1) yes, (2) no. |
| INT telProdNpMonIfcPPPIPCPCtrlOptVJCmpRem | 1.3.6.1.4.1.2007.4.1.2.2.2.10.2.2.1.5 | INTEGER | read-only | Van Jacobson compression selected or not in the remote end: (0) non negotiated, (1) yes, (2) no. |
| telProdNpMonIfcPPPIPCPStatsTable | 1.3.6.1.4.1.2007.4.1.2.2.2.10.2.3 | not-accessible | This table contains statistics of the IPCP protocol. The entry number is determined by the interface number (table index). | |
| telProdNpMonIfcPPPIPCPStatsEntry | 1.3.6.1.4.1.2007.4.1.2.2.2.10.2.3.1 | not-accessible | Each entry contains the node interface number, which is the table index, a variable to check variables deletion (corresponding counters reset), and information about the following counters values: number of sent and received Configure Request NCP frames, number of sent and received Configure Ack NCP frames, number of sent and received Configure Nak NCP frames, number of sent and received Configure Reject NCP frames, number of sent and received Terminate Request NCP frames, number of sent and received Terminate Ack NCP frames. | |
| INT telProdNpMonIfcPPPIPCPStIndex | 1.3.6.1.4.1.2007.4.1.2.2.2.10.2.3.1.1 | INTEGER | read-only | Interface number of the node, that indicates the corresponding table entry (it is the table index). |
| INT telProdNpMonIfcPPPIPCPStClear | 1.3.6.1.4.1.2007.4.1.2.2.2.10.2.3.1.2 | INTEGER | read-write | This variable when is readed shows the output from the last counter restart attempt: the value is 2 (ok) if the restart was performed succesfully, 3 (error) if an error ocurred and 4 (undefined) if nobody has tried to restart the counters yet. In set operations, the value 1 (it is the only value that can be assigned by a writing operation) causes a counter restart. |
| CTR telProdNpMonIfcPPPIPCPStConfReqRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.2.3.1.3 | Counter | read-only | Number of Configure Request NCP frames received through the interface number shown in the index. |
| CTR telProdNpMonIfcPPPIPCPStConfReqTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.2.3.1.4 | Counter | read-only | Number of Configure Request NCP frames transmitted through the interface number shown in the index. |
| CTR telProdNpMonIfcPPPIPCPStConfAckRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.2.3.1.5 | Counter | read-only | Number of Configure Ack NCP frames received through the interface number shown in the index. |
| CTR telProdNpMonIfcPPPIPCPStConfAckTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.2.3.1.6 | Counter | read-only | Number of Configure Ack NCP frames transmitted through the interface number shown in the index. |
| CTR telProdNpMonIfcPPPIPCPStConfNakRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.2.3.1.7 | Counter | read-only | Number of Configure Nak NCP frames received through the interface number shown in the index. |
| CTR telProdNpMonIfcPPPIPCPStConfNakTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.2.3.1.8 | Counter | read-only | Number of Configure Nak NCP frames transmitted through the interface number shown in the index. |
| CTR telProdNpMonIfcPPPIPCPStConfRejRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.2.3.1.9 | Counter | read-only | Number of Configure Reject NCP frames received through the interface number shown in the index. |
| CTR telProdNpMonIfcPPPIPCPStConfRejTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.2.3.1.10 | Counter | read-only | Number of Configure Reject NCP frames transmitted through the interface number shown in the index. |
| CTR telProdNpMonIfcPPPIPCPStTermReqRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.2.3.1.11 | Counter | read-only | Number of Terminate Request NCP frames received through the interface number shown in the index. |
| CTR telProdNpMonIfcPPPIPCPStTermReqTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.2.3.1.12 | Counter | read-only | Number of Terminate Request NCP frames transmitted through the interface number shown in the index. |
| CTR telProdNpMonIfcPPPIPCPStTermAckRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.2.3.1.13 | Counter | read-only | Number of Terminate Ack NCP frames received through the interface number shown in the index. |
| CTR telProdNpMonIfcPPPIPCPStTermAckTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.2.3.1.14 | Counter | read-only | Number of Terminate Ack NCP frames transmitted through the interface number shown in the index. |
| telProdNpMonIfcPPPVJStatsTable | 1.3.6.1.4.1.2007.4.1.2.2.2.10.3 | not-accessible | This table contains monitoring parameters related to Van Jacobson compression. The entry number is determined by the interface number. | |
| telProdNpMonIfcPPPVJStatsEntry | 1.3.6.1.4.1.2007.4.1.2.2.2.10.3.1 | not-accessible | Each entry contains the node interface number, which is the table index, a variable to check variables deletion (corresponding counters reset), and information about the following counters values: number of outbound TCP/IP packets, number of outbound compressed TCP/IP packets, number of searchs of the connection state, number of times the connection state wasn't found, number of inbound TCP/IP packets, number of inbound compressed TCP/IP packets, number of inbound TCP/IP packets classified as unknown and number of tossed error inbound TCP/IP packets. | |
| INT telProdNpMonIfcPPPVJStIndex | 1.3.6.1.4.1.2007.4.1.2.2.2.10.3.1.1 | INTEGER | read-only | Interface number of the node, that indicates the corresponding table entry (it is the table index). |
| INT telProdNpMonIfcPPPVJStClear | 1.3.6.1.4.1.2007.4.1.2.2.2.10.3.1.2 | INTEGER | read-write | This variable when is readed shows the output from the last counter restart attemp: the value is 2 (ok) if the restart was performed succesfully, 3 (error) if an error ocurred and 4 (undefined) if nobody has tried to restart the counters yet. In set operations, the value 1 (it is the only value that can be assigned by a writing operation) causes a counter restart. |
| CTR telProdNpMonIfcPPPVJStOutPackets | 1.3.6.1.4.1.2007.4.1.2.2.2.10.3.1.3 | Counter | read-only | Number of outbound TCP/IP packets. |
| CTR telProdNpMonIfcPPPVJStOutComprPkts | 1.3.6.1.4.1.2007.4.1.2.2.2.10.3.1.4 | Counter | read-only | Number of outbound compressed TCP/IP packets. |
| CTR telProdNpMonIfcPPPVJStSearches | 1.3.6.1.4.1.2007.4.1.2.2.2.10.3.1.5 | Counter | read-only | Number of searchs of the connection state. |
| CTR telProdNpMonIfcPPPVJStNoConnState | 1.3.6.1.4.1.2007.4.1.2.2.2.10.3.1.6 | Counter | read-only | Times the connection state could not be found. |
| CTR telProdNpMonIfcPPPVJStInUncomPkts | 1.3.6.1.4.1.2007.4.1.2.2.2.10.3.1.7 | Counter | read-only | Number of inbound uncompressed TCP/IP packets. |
| CTR telProdNpMonIfcPPPVJStInComprPkts | 1.3.6.1.4.1.2007.4.1.2.2.2.10.3.1.8 | Counter | read-only | Number of inbound compressed TCP/IP packets. |
| CTR telProdNpMonIfcPPPVJStInUnkTypePkts | 1.3.6.1.4.1.2007.4.1.2.2.2.10.3.1.9 | Counter | read-only | Number of inbound TCP/IP packets classified as unkown. |
| CTR telProdNpMonIfcPPPVJStInPktsTossErr | 1.3.6.1.4.1.2007.4.1.2.2.2.10.3.1.10 | Counter | read-only | Number of inbound TCP/IP packets tossed error. |
| telProdNpMonIfcPPPCrtpStatsTable | 1.3.6.1.4.1.2007.4.1.2.2.2.10.4 | not-accessible | This table contains monitoring parameters related to CRTP compression. The entry number is determined by the interface number. | |
| telProdNpMonIfcPPPCrtpStatsEntry | 1.3.6.1.4.1.2007.4.1.2.2.2.10.4.1 | not-accessible | Each entry contains the node interface number, which is the table index, a variable to check variables deletion (corresponding counters reset), and information about the following counters values: number of outbound RTP packets, number of outbound compressed RTP packets, number of searchs of the connection state, number of times the connection state wasn't found, number of inbound RTP packets, number of inbound compressed RTP packets, number of inbound RTP packets classified as unknown and number of inbound RTP Context State packets. | |
| INT telProdNpMonIfcPPPCrtpStIndex | 1.3.6.1.4.1.2007.4.1.2.2.2.10.4.1.1 | INTEGER | read-only | Interface number of the node, that indicates the corresponding table entry (it is the table index). |
| INT telProdNpMonIfcPPPCrtpStClear | 1.3.6.1.4.1.2007.4.1.2.2.2.10.4.1.2 | INTEGER | read-write | This variable when is readed shows the output from the last counter restart attempt: the value is 2 (ok) if the restart was performed succesfully, 3 (error) if an error ocurred and 4 (undefined) if nobody has tried to restart the counters yet. In set operations, the value 1 (it is the only value that can be assigned by a writing operation) causes a counter restart. |
| CTR telProdNpMonIfcPPPCrtpStOutPackets | 1.3.6.1.4.1.2007.4.1.2.2.2.10.4.1.3 | Counter | read-only | Number of outbound RTP packets. |
| CTR telProdNpMonIfcPPPCrtpStOutComprPkts | 1.3.6.1.4.1.2007.4.1.2.2.2.10.4.1.4 | Counter | read-only | Number of outbound compressed RTP packets. |
| CTR telProdNpMonIfcPPPCrtpStSearches | 1.3.6.1.4.1.2007.4.1.2.2.2.10.4.1.5 | Counter | read-only | Number of searchs of the connection state. |
| CTR telProdNpMonIfcPPPCrtpStNoConnState | 1.3.6.1.4.1.2007.4.1.2.2.2.10.4.1.6 | Counter | read-only | Times the connection state could not be found. |
| CTR telProdNpMonIfcPPPCrtpStInUncomPkts | 1.3.6.1.4.1.2007.4.1.2.2.2.10.4.1.7 | Counter | read-only | Number of inbound uncompressed RTP packets. |
| CTR telProdNpMonIfcPPPCrtpStInComprPkts | 1.3.6.1.4.1.2007.4.1.2.2.2.10.4.1.8 | Counter | read-only | Number of inbound compressed RTP packets. |
| CTR telProdNpMonIfcPPPCrtpStInUnkTypePkts | 1.3.6.1.4.1.2007.4.1.2.2.2.10.4.1.9 | Counter | read-only | Number of inbound RTP packets classified as unkown. |
| CTR telProdNpMonIfcPPPCrtpStInContextStPkts | 1.3.6.1.4.1.2007.4.1.2.2.2.10.4.1.10 | Counter | read-only | Number of inbound RTP Context State packets |
| telProdNpMonIfcPPPCommandGroup | 1.3.6.1.4.1.2007.4.1.2.2.2.10.5 | |||
| telProdNpMonIfcPPPCommClearTable | 1.3.6.1.4.1.2007.4.1.2.2.2.10.5.1 | not-accessible | Table of CLEAR commands for different interfaces. The entry number is determined by the interface number and indicates the interface type to which this command is applied. | |
| telProdNpMonIfcPPPCommClearEntry | 1.3.6.1.4.1.2007.4.1.2.2.2.10.5.1.1 | not-accessible | Each entry contains the interface number, that is the table index, and indicates the interface the CLEAR command is applied on, a variable to perform the CLEAR operation: restart interface statistics, that when is readed indicates the output of the last CLEAR operation. | |
| INT telProdNpMonIfcPPPCommClearIndex | 1.3.6.1.4.1.2007.4.1.2.2.2.10.5.1.1.1 | INTEGER | read-only | Interface number of the node, that indicates the corresponding table entry (it is the table index). |
| INT telProdNpMonIfcPPPCommClear | 1.3.6.1.4.1.2007.4.1.2.2.2.10.5.1.1.2 | INTEGER | read-write | This variable when is readed shows the output from the last attempt to restart interface statistics. Possible values are: 2 (ok) if the restart was performed succesfully, 3 (error) if an error ocurred and 4 (undefined) if nobody has tried to restart the table yet. In set operations, the value 1 (it is the only value that can be assigned by a writing operation) causes statistics to restart. |
| telProdNpMonIfcPPPCommResetTable | 1.3.6.1.4.1.2007.4.1.2.2.2.10.5.2 | not-accessible | Table of RESET-LINK commands for different type of interfaces. The entry number is determined by the interface number, and indicates which interface we are considering. | |
| telProdNpMonIfcPPPCommResetEntry | 1.3.6.1.4.1.2007.4.1.2.2.2.10.5.2.1 | not-accessible | Each entry contains the node interface number, that is the table index, and indicates the interface the RESET-LINK command is applied on, and a variable to perform the RESET-LINK operation: pull down the PPP link and when the variable is readed indicates the output of the last operation attempt. | |
| INT telProdNpMonIfcPPPCommResetIndex | 1.3.6.1.4.1.2007.4.1.2.2.2.10.5.2.1.1 | INTEGER | read-only | Interface number of the node, that indicates the corresponding table entry (it is the table index). |
| INT telProdNpMonIfcPPPCommReset | 1.3.6.1.4.1.2007.4.1.2.2.2.10.5.2.1.2 | INTEGER | read-write | This variable when is readed shows the output from the last attempt to drop PPP link. Possible values are: 2 (ok) if the operation was performed succesfully, 3 (error) if an error ocurred and 4 (undefined) if nobody has tried to drop the link yet. In set operations, the value 1 (it is the only value that can be assigned by a writing operation) implies the PPP link is going to be dropped. |
| telProdNpMonIfcPPPCCPGroup | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6 | |||
| telProdNpMonIfcPPPCCPControlGloTable | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.1 | not-accessible | This table contains CCP global parameters. This table has an entry for each PPP interface. The entry number is determined by the corresponding interface number (table index). | |
| telProdNpMonIfcPPPCCPControlGloEntry | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.1.1 | not-accessible | Each entry contains the node interface number which is the table index, and variables that shows if the CCP protocol is enabled or disabled, and the current state of the CCP protocol. | |
| INT telProdNpMonIfcPPPCCPCtrlGloIndex | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.1.1.1 | INTEGER | read-only | Interface number of the node, that indicates the corresponding table entry (it is the table index). |
| INT telProdNpMonIfcPPPCCPCtrlGloCCP | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.1.1.2 | INTEGER | read-only | This variable indicates if the CCP protocol is enabled or disabled. |
| INT telProdNpMonIfcPPPCCPCtrlGloState | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.1.1.3 | INTEGER | read-only | Current protocol state. The possible values of the variable are integer numbers between 0 and 9. Each number is related to a feasible state: (0) initial, (1) starting, (2) closed, (3) stopped, (4) closing, (5) stopping, (6) req-sent, (7) ack-rcvd, (8) ack-sent, (9) opened. |
| telProdNpMonIfcPPPCCPControlOptionsTable | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.2 | not-accessible | This table contains the variables that informs about the CCP protocol options. The entry number is determined by the interface value (table index). | |
| telProdNpMonIfcPPPCCPControlOptionsEntry | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.2.1 | not-accessible | Each entry contains the node interface number, which is the table index, the output and input encapsulated protocol, the output and input event, the type of configuration format associated to the output and input, the number of output and input negotiated histories, the output and input negotiated check mode, the output and input negotiated process mode, the output and input session and the output and input sequence number. | |
| INT telProdNpMonIfcPPPCCPCtrlOptIndex | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.2.1.1 | INTEGER | read-only | Interface number of the node, that indicates the corresponding table entry (it is the table index). |
| INT telProdNpMonIfcPPPCCPCtrlOptProtOut | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.2.1.2 | INTEGER | read-only | Output encapsulated protocol. It can be used PPP (1), MPPP (2) or other different of thesesones (3). |
| INT telProdNpMonIfcPPPCCPCtrlOptProtIn | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.2.1.3 | INTEGER | read-only | Input encapsulated protocol. It can be used PPP (1), MPPP (2) or other different of thesesones (3). |
| INT telProdNpMonIfcPPPCCPCtrlOptEventOut | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.2.1.4 | INTEGER | read-only | Output event. |
| INT telProdNpMonIfcPPPCCPCtrlOptEventIn | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.2.1.5 | INTEGER | read-only | Input event. |
| INT telProdNpMonIfcPPPCCPCtrlOptTypeOut | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.2.1.6 | INTEGER | read-only | Type of configuration format associated to the output. |
| INT telProdNpMonIfcPPPCCPCtrlOptTypeIn | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.2.1.7 | INTEGER | read-only | Type of configuration format associated to the input. |
| STR telProdNpMonIfcPPPCCPCtrlOptHistOut | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.2.1.8 | DisplayString | read-only | The number of output negotiated histories. This variable indicates pack to pack or the corresponding number. |
| STR telProdNpMonIfcPPPCCPCtrlOptHistIn | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.2.1.9 | DisplayString | read-only | The number of input negotiated histories. This variable indicates pack to pack or the corresponding number. |
| INT telProdNpMonIfcPPPCCPCtrlOptChkModOut | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.2.1.10 | INTEGER | read-only | Output negotiated check mode. |
| INT telProdNpMonIfcPPPCCPCtrlOptChkModIn | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.2.1.11 | INTEGER | read-only | Input negotiated check mode. |
| INT telProdNpMonIfcPPPCCPCtrlOptPrcModOut | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.2.1.12 | INTEGER | read-only | Output negotiated process mode. |
| INT telProdNpMonIfcPPPCCPCtrlOptPrcModIn | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.2.1.13 | INTEGER | read-only | Input negotiated process mode. |
| STR telProdNpMonIfcPPPCCPCtrlOptSessionOut | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.2.1.14 | DisplayString | read-only | Output session identifier. |
| STR telProdNpMonIfcPPPCCPCtrlOptSessionIn | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.2.1.15 | DisplayString | read-only | Input session identifier. |
| INT telProdNpMonIfcPPPCCPCtrlOptSeqNumOut | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.2.1.16 | INTEGER | read-only | Output sequence number. |
| INT telProdNpMonIfcPPPCCPCtrlOptSeqNumIn | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.2.1.17 | INTEGER | read-only | Input sequence number. |
| telProdNpMonIfcPPPCCPStatsTable | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.3 | not-accessible | This table contains statistics of the CCP protocol. The entry number is determined by the interface number (table index). | |
| telProdNpMonIfcPPPCCPStatsEntry | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.3.1 | not-accessible | Each entry contains the node interface number, which is the table index, a variable to check variables deletion (corresponding counters reset), and information about the following counters values: number of sent and received Configure Request CCP frames, number of sent and received Configure Ack CCP frames, number of sent and received Configure Nak CCP frames, number of sent and received Configure Reject CCP frames, number of sent and received Terminate Request CCP frames, number of sent and received Terminate Ack CCP frames, number of sent and received Terminate Ack CCP frames, number of processed frames received for uncompress and compress, number of processed bytes received for uncompress and compress, number of uncompressed and compressed frames, number of uncompressed and compressed bytes, number of non processed frames received for uncompress and compress, number of frames with errors in compression and uncompression, number of received and sent Reset Request CCP frames, number of received and sent Reset Ack CCP frames, number of sequence errors in reception and transmission, number of LCB errors in reception and transmission and number of received and sent header errors. | |
| INT telProdNpMonIfcPPPCCPStIndex | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.3.1.1 | INTEGER | read-only | Interface number of the node, that indicates the corresponding table entry (it is the table index). |
| INT telProdNpMonIfcPPPCCPStClear | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.3.1.2 | INTEGER | read-write | This variable when is readed shows the output from the last counter restart attempt: the value is 2 (ok) if the restart was performed succesfully, 3 (error) if an error ocurred and 4 (undefined) if nobody has tried to restart the counters yet. In set operations, the value 1 (it is the only value that can be assigned by a writing operation) causes a counter restart. |
| CTR telProdNpMonIfcPPPCCPStConfReqRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.3.1.3 | Counter | read-only | Number of received Configure Request CCP frames. |
| CTR telProdNpMonIfcPPPCCPStConfReqTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.3.1.4 | Counter | read-only | Number of sent Configure Request CCP frames. |
| CTR telProdNpMonIfcPPPCCPStConfAckRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.3.1.5 | Counter | read-only | Number of received Configure Ack CCP frames. |
| CTR telProdNpMonIfcPPPCCPStConfAckTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.3.1.6 | Counter | read-only | Number of sent Configure Ack CCP frames. |
| CTR telProdNpMonIfcPPPCCPStConfNakRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.3.1.7 | Counter | read-only | Number of received Configure Nak CCP frames. |
| CTR telProdNpMonIfcPPPCCPStConfNakTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.3.1.8 | Counter | read-only | Number of sent Configure Nak CCP frames. |
| CTR telProdNpMonIfcPPPCCPStConfRejRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.3.1.9 | Counter | read-only | Number of received Configure Reject CCP frames. |
| CTR telProdNpMonIfcPPPCCPStConfRejTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.3.1.10 | Counter | read-only | Number of sent Configure Reject CCP frames. |
| CTR telProdNpMonIfcPPPCCPStTermReqRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.3.1.11 | Counter | read-only | Number of received Terminate Request CCP frames. |
| CTR telProdNpMonIfcPPPCCPStTermReqTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.3.1.12 | Counter | read-only | Number of sent Terminate Request CCP frames. |
| CTR telProdNpMonIfcPPPCCPStTermAckRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.3.1.13 | Counter | read-only | Number of received Terminate Ack CCP frames. |
| CTR telProdNpMonIfcPPPCCPStTermAckTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.3.1.14 | Counter | read-only | Number of sent Terminate Ack CCP frames. |
| CTR telProdNpMonIfcPPPCCPStProcFrsRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.3.1.15 | Counter | read-only | Number of processed frames received for uncompress. |
| CTR telProdNpMonIfcPPPCCPStProcFrsTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.3.1.16 | Counter | read-only | Number of processed frames received for compress. |
| CTR telProdNpMonIfcPPPCCPStProcBytRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.3.1.17 | Counter | read-only | Number of processed bytes received for uncompress. |
| CTR telProdNpMonIfcPPPCCPStProcBytTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.3.1.18 | Counter | read-only | Number of processed bytes received for compress. |
| CTR telProdNpMonIfcPPPCCPStFramesRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.3.1.19 | Counter | read-only | Number of uncompressed frames. |
| CTR telProdNpMonIfcPPPCCPStFramesTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.3.1.20 | Counter | read-only | Number of compressed frames. |
| CTR telProdNpMonIfcPPPCCPStBytesRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.3.1.21 | Counter | read-only | Number of uncompressed bytes. |
| CTR telProdNpMonIfcPPPCCPStBytesTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.3.1.22 | Counter | read-only | Number of compressed bytes. |
| CTR telProdNpMonIfcPPPCCPStUncompFrsRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.3.1.23 | Counter | read-only | Number of non processed frames received for uncompress. |
| CTR telProdNpMonIfcPPPCCPStUncompFrsTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.3.1.24 | Counter | read-only | Number of non processed frames received for compress. |
| CTR telProdNpMonIfcPPPCCPStErrorFrsRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.3.1.25 | Counter | read-only | Number of frames whith errors in compression. |
| CTR telProdNpMonIfcPPPCCPStErrorFrsTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.3.1.26 | Counter | read-only | Number of frames whith errors in uncompression. |
| CTR telProdNpMonIfcPPPCCPStResetReqRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.3.1.27 | Counter | read-only | Number of received Reset Request CCP frames. |
| CTR telProdNpMonIfcPPPCCPStResetReqTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.3.1.28 | Counter | read-only | Number of sent Reset Request CCP frames. |
| CTR telProdNpMonIfcPPPCCPStResetAckRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.3.1.29 | Counter | read-only | Number of received Reset Ack CCP frames. |
| CTR telProdNpMonIfcPPPCCPStResetAckTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.3.1.30 | Counter | read-only | Number of sent Reset Ack CCP frames. |
| CTR telProdNpMonIfcPPPCCPStSeqErrorsRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.3.1.31 | Counter | read-only | Number of sequence errors in reception. |
| CTR telProdNpMonIfcPPPCCPStSeqErrorsTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.3.1.32 | Counter | read-only | Number of sequence errors in transmission. |
| CTR telProdNpMonIfcPPPCCPStLCBErrorsRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.3.1.33 | Counter | read-only | Number of LCB errors in reception. |
| CTR telProdNpMonIfcPPPCCPStLCBErrorsTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.3.1.34 | Counter | read-only | Number of LCB errors in transmission. |
| CTR telProdNpMonIfcPPPCCPStHdrErrorsRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.3.1.35 | Counter | read-only | Number of received header errors. |
| CTR telProdNpMonIfcPPPCCPStHdrErrorsTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.6.3.1.36 | Counter | read-only | Number of sent header errors. |
| telProdNpMonIfcPPPMPGroup | 1.3.6.1.4.1.2007.4.1.2.2.2.10.7 | |||
| telProdNpMonIfcPPPMPControlGloTable | 1.3.6.1.4.1.2007.4.1.2.2.2.10.7.1 | not-accessible | This table contains Multilink PPP global parameters. This table has an entry for each PPP interface. The entry number is determined by the corresponding interface number (table index). | |
| telProdNpMonIfcPPPMPControlGloEntry | 1.3.6.1.4.1.2007.4.1.2.2.2.10.7.1.1 | not-accessible | Each entry contains the node interface number which is the table index, and variables that shows the remote user name, the number of active links in bundle and the current fragment queue length. | |
| INT telProdNpMonIfcPPPMPCtrlGloIndex | 1.3.6.1.4.1.2007.4.1.2.2.2.10.7.1.1.1 | INTEGER | read-only | Interface number of the node, that indicates the corresponding table entry (it is the table index). |
| STR telProdNpMonIfcPPPMPCtrlGloRemUserName | 1.3.6.1.4.1.2007.4.1.2.2.2.10.7.1.1.2 | DisplayString | read-only | When the authentication is enabled, this variable indicates the remote user name. In other case, it contains a empty string. |
| INT telProdNpMonIfcPPPMPCtrlGloBundleLinks | 1.3.6.1.4.1.2007.4.1.2.2.2.10.7.1.1.3 | INTEGER | read-only | This variable shows the number of active links in bundle. |
| INT telProdNpMonIfcPPPMPCtrlGloFragments | 1.3.6.1.4.1.2007.4.1.2.2.2.10.7.1.1.4 | INTEGER | read-only | This variable shows the current fragment queue length. |
| INT telProdNpMonIfcPPPMPCtrlGloRTFragments | 1.3.6.1.4.1.2007.4.1.2.2.2.10.7.1.1.5 | INTEGER | read-only | This variable shows the current fragment queue length for real time traffic. |
| telProdNpMonIfcPPPMPControlOptionsTable | 1.3.6.1.4.1.2007.4.1.2.2.2.10.7.2 | not-accessible | This table contains the variables that informs about the Multilink PPP options. The entry number is determined by the interface value (table index). | |
| telProdNpMonIfcPPPMPControlOptionsEntry | 1.3.6.1.4.1.2007.4.1.2.2.2.10.7.2.1 | not-accessible | Each entry contains the node interface number, which is the table index, the local and remote maximum packet size accepted in reception, if short sequence number header format is enabled in the local and remote end, the local and remote associated class and the local and remote address. | |
| INT telProdNpMonIfcPPPMPCtrlOptIndex | 1.3.6.1.4.1.2007.4.1.2.2.2.10.7.2.1.1 | INTEGER | read-only | Interface number of the node, that indicates the corresponding table entry (it is the table index). |
| INT telProdNpMonIfcPPPMPCtrlOptMRRULoc | 1.3.6.1.4.1.2007.4.1.2.2.2.10.7.2.1.2 | INTEGER | read-only | Maximum packet size accepted in reception associated to the local end. |
| INT telProdNpMonIfcPPPMPCtrlOptMRRURem | 1.3.6.1.4.1.2007.4.1.2.2.2.10.7.2.1.3 | INTEGER | read-only | Maximum packet size accepted in reception associated to the remote end. |
| INT telProdNpMonIfcPPPMPCtrlOptSSNLoc | 1.3.6.1.4.1.2007.4.1.2.2.2.10.7.2.1.4 | INTEGER | read-only | This variable shows if the short sequence number header format in the local end is enabled or disabled. |
| INT telProdNpMonIfcPPPMPCtrlOptSSNRem | 1.3.6.1.4.1.2007.4.1.2.2.2.10.7.2.1.5 | INTEGER | read-only | This variable shows if the short sequence number header format in the remote end is enabled or disabled. |
| INT telProdNpMonIfcPPPMPCtrlOptClassLoc | 1.3.6.1.4.1.2007.4.1.2.2.2.10.7.2.1.6 | INTEGER | read-only | This variable shows the class associated to the local end. |
| INT telProdNpMonIfcPPPMPCtrlOptClassRem | 1.3.6.1.4.1.2007.4.1.2.2.2.10.7.2.1.7 | INTEGER | read-only | This variable shows the class associated to the remote end. |
| STR telProdNpMonIfcPPPMPCtrlOptAddressLoc | 1.3.6.1.4.1.2007.4.1.2.2.2.10.7.2.1.8 | DisplayString | read-only | This variable indicates the address associated to the local end. It is a string that must be interpreted according to the local class. |
| STR telProdNpMonIfcPPPMPCtrlOptAddressRem | 1.3.6.1.4.1.2007.4.1.2.2.2.10.7.2.1.9 | DisplayString | read-only | This variable indicates the address associated to the remote end. It is a string that must be interpreted according to the remote class. |
| INT telprodNpMonIfcPPPMPCtrlOptMHFNeg | 1.3.6.1.4.1.2007.4.1.2.2.2.10.7.2.1.10 | INTEGER | read-only | This variable shows if the multiclass multilink option has been negotiated. |
| telProdNpMonIfcPPPMPStatsTable | 1.3.6.1.4.1.2007.4.1.2.2.2.10.7.3 | not-accessible | This table contains statistics of the Multilink PPP. The entry number is determined by the interface number (table index). | |
| telProdNpMonIfcPPPMPStatsEntry | 1.3.6.1.4.1.2007.4.1.2.2.2.10.7.3.1 | not-accessible | Each entry contains the node interface number, which is the table index, a variable to check variables deletion (corresponding counters reset), and information about the following counters values: number of sent and received frames, number of sent and received bytes, number of queued frames, number of error frames and number of sequence loss in reception. | |
| INT telProdNpMonIfcPPPMPStIndex | 1.3.6.1.4.1.2007.4.1.2.2.2.10.7.3.1.1 | INTEGER | read-only | Interface number of the node, that indicates the corresponding table entry (it is the table index). |
| INT telProdNpMonIfcPPPMPStClear | 1.3.6.1.4.1.2007.4.1.2.2.2.10.7.3.1.2 | INTEGER | read-write | This variable when is readed shows the output from the last counter restart attempt: the value is 2 (ok) if the restart was performed succesfully, 3 (error) if an error ocurred and 4 (undefined) if nobody has tried to restart the counters yet. In set operations, the value 1 (it is the only value that can be assigned by a writing operation) causes a counter restart. |
| CTR telProdNpMonIfcPPPMPStFramesTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.7.3.1.3 | Counter | read-only | Number of sent frames. |
| CTR telProdNpMonIfcPPPMPStFramesRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.7.3.1.4 | Counter | read-only | Number of received frames. |
| CTR telProdNpMonIfcPPPMPStBytesTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.7.3.1.5 | Counter | read-only | Number of sent bytes. |
| CTR telProdNpMonIfcPPPMPStBytesRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.7.3.1.6 | Counter | read-only | Number of received bytes. |
| CTR telProdNpMonIfcPPPMPStQueuedFrm | 1.3.6.1.4.1.2007.4.1.2.2.2.10.7.3.1.7 | Counter | read-only | Number of queued received frames. |
| CTR telProdNpMonIfcPPPMPStErrorFrm | 1.3.6.1.4.1.2007.4.1.2.2.2.10.7.3.1.8 | Counter | read-only | Number of rejected frames due to errors. |
| CTR telProdNpMonIfcPPPMPStSeqLoss | 1.3.6.1.4.1.2007.4.1.2.2.2.10.7.3.1.9 | Counter | read-only | Number of sequence loss in reception. |
| CTR telProdNpMonIfcPPPMPStRTFramesTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.7.3.1.10 | Counter | read-only | Number of sent real time frames. |
| CTR telProdNpMonIfcPPPMPStRTFramesRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.7.3.1.11 | Counter | read-only | Number of received real time frames. |
| CTR telProdNpMonIfcPPPMPStRTBytesTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.7.3.1.12 | Counter | read-only | Number of sent real time bytes. |
| CTR telProdNpMonIfcPPPMPStRTBytesRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.7.3.1.13 | Counter | read-only | Number of received real time bytes. |
| CTR telProdNpMonIfcPPPMPStRTQueuedFrm | 1.3.6.1.4.1.2007.4.1.2.2.2.10.7.3.1.14 | Counter | read-only | Number of queued received real time frames. |
| CTR telProdNpMonIfcPPPMPStRTErrorFrm | 1.3.6.1.4.1.2007.4.1.2.2.2.10.7.3.1.15 | Counter | read-only | Number of rejected real time frames due to errors. |
| CTR telProdNpMonIfcPPPMPStRTSeqLoss | 1.3.6.1.4.1.2007.4.1.2.2.2.10.7.3.1.16 | Counter | read-only | Number of sequence loss in reception of real time frames. |
| telProdNpMonIfcPPPDialTable | 1.3.6.1.4.1.2007.4.1.2.2.2.10.8 | not-accessible | This table contains information about monitoring parameters associated to Dial part of PPP. The entry number is determined by the PPP interface value and the Dial order number. | |
| telProdNpMonIfcPPPDialEntry | 1.3.6.1.4.1.2007.4.1.2.2.2.10.8.1 | not-accessible | Each entry contains the PPP interface number of the node, the Dial order number, the Dial profile name, the remote address, the local address, the number of the interface over the PPP is mounted, the requested circuit identifier, the Dial circuit state and the assigned circuit identifier. | |
| INT telProdNpMonIfcPPPDialIfcIndex | 1.3.6.1.4.1.2007.4.1.2.2.2.10.8.1.1 | INTEGER | read-only | PPP interface number of the node (first table index). |
| INT telProdNpMonIfcPPPDialOrderIndex | 1.3.6.1.4.1.2007.4.1.2.2.2.10.8.1.2 | INTEGER | read-only | Dial order number inside the PPP interface (second table index). |
| STR telProdNpMonIfcPPPDialName | 1.3.6.1.4.1.2007.4.1.2.2.2.10.8.1.3 | DisplayString | read-only | Dial profile name. |
| STR telProdNpMonIfcPPPDialDesAddr | 1.3.6.1.4.1.2007.4.1.2.2.2.10.8.1.4 | DisplayString | read-only | If the interface that support the PPP interface is switched, this variable indicates the remote address. |
| STR telProdNpMonIfcPPPDialLocAddr | 1.3.6.1.4.1.2007.4.1.2.2.2.10.8.1.5 | DisplayString | read-only | If the interface that support the PPP interface is switched, this variable indicates the local address. |
| INT telProdNpMonIfcPPPDialLowIfc | 1.3.6.1.4.1.2007.4.1.2.2.2.10.8.1.6 | INTEGER | read-only | Number of the interface the PPP is mounted over. In this case, the interfaces are numbered from 0, the same as in console. |
| INT telProdNpMonIfcPPPDialCircReq | 1.3.6.1.4.1.2007.4.1.2.2.2.10.8.1.7 | INTEGER | read-only | When the interface that support the PPP interface is composed of different subinterfaces, this variable specifies the requested circuit identifier. Its value must be 255 to indicate the choice of the circuit number is free. |
| INT telProdNpMonIfcPPPDialCircStatus | 1.3.6.1.4.1.2007.4.1.2.2.2.10.8.1.8 | INTEGER | read-only | Dial circuit state. |
| INT telProdNpMonIfcPPPDialCircAsig | 1.3.6.1.4.1.2007.4.1.2.2.2.10.8.1.9 | INTEGER | read-only | When the interface that support the PPP interface is composed of different subinterfaces, this variable specifies the assigned circuit identifier. If the Dial circuit state is not OPEN(4), the requested circuit identifier is shown. |
| telProdNpMonIfcPPPNCPGroup | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9 | |||
| telProdNpMonIfcPPPNCPIPCPGroup | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.1 | |||
| telProdNpMonIfcPPPNCPIPCPControlGloTable | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.1.1 | not-accessible | This table contains IPCP global parameters. This table has an entry for each PPP interface of the node. The entry number is determined by the corresponding interface number (table index). | |
| telProdNpMonIfcPPPNCPIPCPControlGloEntry | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.1.1.1 | not-accessible | Each entry contains the node interface number which is the table index, and a variable that shows the current state of the IPCP protocol. | |
| INT telProdNpMonIfcPPPNCPIPCPCtrlGloIndex | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.1.1.1.1 | INTEGER | read-only | Interface number of the node, that indicates the corresponding table entry (it is the table index). |
| INT telProdNpMonIfcPPPNCPIPCPCtrlGloState | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.1.1.1.2 | INTEGER | read-only | Current protocol state. The possible values of the variable are integer numbers between 0 and 9. Each number is related to a feasible state: (0) initial, (1) starting, (2) closed, (3) stopped, (4) closing, (5) stopping, (6) req-sent, (7) ack-rcvd, (8) ack-sent, (9) opened. |
| telProdNpMonIfcPPPNCPIPCPControlOptionsTable | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.1.2 | not-accessible | This table contains information about parameters used to monitor received and transmitted options during the network level protocol setup. The entry number is determined by the interface value (table index). | |
| telProdNpMonIfcPPPNCPIPCPControlOptionsEntry | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.1.2.1 | not-accessible | Each entry contains the node interface number, which is the table index, the assigned IP address (in case of dinamic asignation), remote end IP address (if received) and if the Van Jacobson compression option has been selected at any end (local or remote). | |
| INT telProdNpMonIfcPPPNCPIPCPCtrlOptIndex | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.1.2.1.1 | INTEGER | read-only | Interface number of the node, that indicates the corresponding table entry (it is the table index). |
| IP telProdNpMonIfcPPPNCPIPCPCtrlOptIpAddrLoc | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.1.2.1.2 | IpAddress | read-only | The IP address assigned (supposing dinamic assignation has been selected). |
| IP telProdNpMonIfcPPPNCPIPCPCtrlOptIpAddrRem | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.1.2.1.3 | IpAddress | read-only | The remote IP address (supposing it has been received). |
| INT telProdNpMonIfcPPPNCPIPCPCtrlOptVJCmpLoc | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.1.2.1.4 | INTEGER | read-only | Van Jacobson compression selected or not in the local end: (1) yes, (2) no. |
| INT telProdNpMonIfcPPPNCPIPCPCtrlOptVJCmpRem | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.1.2.1.5 | INTEGER | read-only | Van Jacobson compression selected or not in the remote end: (0) non negotiated, (1) yes, (2) no. |
| telProdNpMonIfcPPPNCPIPCPStatsTable | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.1.3 | not-accessible | This table contains statistics of the IPCP protocol. The entry number is determined by the interface number (table index). | |
| telProdNpMonIfcPPPNCPIPCPStatsEntry | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.1.3.1 | not-accessible | Each entry contains the node interface number, which is the table index, a variable to check variables deletion (corresponding counters reset), and information about the following counters values: number of sent and received Configure Request NCP frames, number of sent and received Configure Ack NCP frames, number of sent and received Configure Nak NCP frames, number of sent and received Configure Reject NCP frames, number of sent and received Terminate Request NCP frames, number of sent and received Terminate Ack NCP frames. | |
| INT telProdNpMonIfcPPPNCPIPCPStIndex | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.1.3.1.1 | INTEGER | read-only | Interface number of the node, that indicates the corresponding table entry (it is the table index). |
| INT telProdNpMonIfcPPPNCPIPCPStClear | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.1.3.1.2 | INTEGER | read-write | This variable when is readed shows the output from the last counter restart attempt: the value is 2 (ok) if the restart was performed succesfully, 3 (error) if an error ocurred and 4 (undefined) if nobody has tried to restart the counters yet. In set operations, the value 1 (it is the only value that can be assigned by a writing operation) causes a counter restart. |
| CTR telProdNpMonIfcPPPNCPIPCPStConfReqRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.1.3.1.3 | Counter | read-only | Number of Configure Request NCP frames received through the interface number shown in the index. |
| CTR telProdNpMonIfcPPPNCPIPCPStConfReqTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.1.3.1.4 | Counter | read-only | Number of Configure Request NCP frames transmitted through the interface number shown in the index. |
| CTR telProdNpMonIfcPPPNCPIPCPStConfAckRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.1.3.1.5 | Counter | read-only | Number of Configure Ack NCP frames received through the interface number shown in the index. |
| CTR telProdNpMonIfcPPPNCPIPCPStConfAckTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.1.3.1.6 | Counter | read-only | Number of Configure Ack NCP frames transmitted through the interface number shown in the index. |
| CTR telProdNpMonIfcPPPNCPIPCPStConfNakRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.1.3.1.7 | Counter | read-only | Number of Configure Nak NCP frames received through the interface number shown in the index. |
| CTR telProdNpMonIfcPPPNCPIPCPStConfNakTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.1.3.1.8 | Counter | read-only | Number of Configure Nak NCP frames transmitted through the interface number shown in the index. |
| CTR telProdNpMonIfcPPPNCPIPCPStConfRejRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.1.3.1.9 | Counter | read-only | Number of Configure Reject NCP frames received through the interface number shown in the index. |
| CTR telProdNpMonIfcPPPNCPIPCPStConfRejTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.1.3.1.10 | Counter | read-only | Number of Configure Reject NCP frames transmitted through the interface number shown in the index. |
| CTR telProdNpMonIfcPPPNCPIPCPStTermReqRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.1.3.1.11 | Counter | read-only | Number of Terminate Request NCP frames received through the interface number shown in the index. |
| CTR telProdNpMonIfcPPPNCPIPCPStTermReqTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.1.3.1.12 | Counter | read-only | Number of Terminate Request NCP frames transmitted through the interface number shown in the index. |
| CTR telProdNpMonIfcPPPNCPIPCPStTermAckRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.1.3.1.13 | Counter | read-only | Number of Terminate Ack NCP frames received through the interface number shown in the index. |
| CTR telProdNpMonIfcPPPNCPIPCPStTermAckTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.1.3.1.14 | Counter | read-only | Number of Terminate Ack NCP frames transmitted through the interface number shown in the index. |
| telProdNpMonIfcPPPNCPBCPGroup | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.2 | |||
| telProdNpMonIfcPPPNCPBCPControlGloTable | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.2.1 | not-accessible | This table contains BCP global parameters. This table has an entry for each PPP interface of the node. The entry number is determined by the corresponding interface number (table index). | |
| telProdNpMonIfcPPPNCPBCPControlGloEntry | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.2.1.1 | not-accessible | Each entry contains the node interface number which is the table index, and a variable that shows the current state of the BCP protocol. | |
| INT telProdNpMonIfcPPPNCPBCPCtrlGloIndex | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.2.1.1.1 | INTEGER | read-only | Interface number of the node, that indicates the corresponding table entry (it is the table index). |
| INT telProdNpMonIfcPPPNCPBCPCtrlGloState | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.2.1.1.2 | INTEGER | read-only | Current protocol state. The possible values of the variable are integer numbers between 0 and 9. Each number is related to a feasible state: (0) initial, (1) starting, (2) closed, (3) stopped, (4) closing, (5) stopping, (6) req-sent, (7) ack-rcvd, (8) ack-sent, (9) opened. |
| telProdNpMonIfcPPPNCPBCPControlOptionsTable | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.2.2 | not-accessible | This table contains information about parameters used to monitor received and transmitted options during the network level protocol setup. The entry number is determined by the interface value (table index). | |
| telProdNpMonIfcPPPNCPBCPControlOptionsEntry | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.2.2.1 | not-accessible | Each entry contains the node interface number, which is the table index, local tinygram support and remote tinygram support. | |
| INT telProdNpMonIfcPPPNCPBCPCtrlOptIndex | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.2.2.1.1 | INTEGER | read-only | Interface number of the node, that indicates the corresponding table entry (it is the table index). |
| INT telProdNpMonIfcPPPNCPBCPCtrlOptLineIdLoc | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.2.2.1.2 | INTEGER | read-only | Line Identification configured for SRB on the local end |
| INT telProdNpMonIfcPPPNCPBCPCtrlOptLineIdRem | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.2.2.1.3 | INTEGER | read-only | Line Identification configured for SRB on the remote end |
| INT telProdNpMonIfcPPPNCPBCPCtrlOptMac8023Loc | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.2.2.1.4 | INTEGER | read-only | Reception of IEEE 802.3 frames allowed selected or not in the local end: (1) yes, (2) no. |
| INT telProdNpMonIfcPPPNCPBCPCtrlOptMac8023Rem | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.2.2.1.5 | INTEGER | read-only | Reception of IEEE 802.3 frames allowed selected or not in the remote end: (1) yes, (2) no. |
| INT telProdNpMonIfcPPPNCPBCPCtrlOptMac8025Loc | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.2.2.1.6 | INTEGER | read-only | Reception of IEEE 802.5 frames allowed selected or not in the local end: (1) yes, (2) no. |
| INT telProdNpMonIfcPPPNCPBCPCtrlOptMac8025Rem | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.2.2.1.7 | INTEGER | read-only | Reception of IEEE 802.5 frames allowed selected or not in the remote end: (1) yes, (2) no. |
| INT telProdNpMonIfcPPPNCPBCPCtrlOptMacFddiLoc | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.2.2.1.8 | INTEGER | read-only | Reception of FDDI frames allowed selected or not in the local end: (1) yes, (2) no. |
| INT telProdNpMonIfcPPPNCPBCPCtrlOptMacFddiRem | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.2.2.1.9 | INTEGER | read-only | Reception of FDDI frames allowed selected or not in the remote end: (1) yes, (2) no. |
| INT telProdNpMonIfcPPPNCPBCPCtrlOptTinyLoc | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.2.2.1.10 | INTEGER | read-only | Tinygram compress support selected or not in the local end: (1) yes, (2) no. |
| INT telProdNpMonIfcPPPNCPBCPCtrlOptTinyRem | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.2.2.1.11 | INTEGER | read-only | Tinygram compress support selected or not in the remote end: (1) yes, (2) no. |
| INT telProdNpMonIfcPPPNCPBCPCtrlOptStp8021DLoc | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.2.2.1.12 | INTEGER | read-only | Reception of 802.1D STP frames allowed selected or not in the local end: (1) yes, (2) no. |
| INT telProdNpMonIfcPPPNCPBCPCtrlOptStp8021DRem | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.2.2.1.13 | INTEGER | read-only | Reception of 802.1D STP frames allowed selected or not in the remote end: (1) yes, (2) no. |
| INT telProdNpMonIfcPPPNCPBCPCtrlOptStpIbmSrbLoc | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.2.2.1.14 | INTEGER | read-only | Reception of IBM SRB STP frames allowed selected or not in the local end: (1) yes, (2) no. |
| INT telProdNpMonIfcPPPNCPBCPCtrlOptStpIbmSrbRem | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.2.2.1.15 | INTEGER | read-only | Reception of IBM SRB STP frames allowed selected or not in the remote end: (1) yes, (2) no. |
| telProdNpMonIfcPPPNCPBCPStatsTable | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.2.3 | not-accessible | This table contains statistics of the BCP protocol. The entry number is determined by the interface number (table index). | |
| telProdNpMonIfcPPPNCPBCPStatsEntry | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.2.3.1 | not-accessible | Each entry contains the node interface number, which is the table index, a variable to check variables deletion (corresponding counters reset), and information about the following counters values: number of sent and received Configure Request NCP frames, number of sent and received Configure Ack NCP frames, number of sent and received Configure Nak NCP frames, number of sent and received Configure Reject NCP frames, number of sent and received Terminate Request NCP frames, number of sent and received Terminate Ack NCP frames. | |
| INT telProdNpMonIfcPPPNCPBCPStIndex | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.2.3.1.1 | INTEGER | read-only | Interface number of the node, that indicates the corresponding table entry (it is the table index). |
| INT telProdNpMonIfcPPPNCPBCPStClear | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.2.3.1.2 | INTEGER | read-write | This variable when is readed shows the output from the last counter restart attempt: the value is 2 (ok) if the restart was performed succesfully, 3 (error) if an error ocurred and 4 (undefined) if nobody has tried to restart the counters yet. In set operations, the value 1 (it is the only value that can be assigned by a writing operation) causes a counter restart. |
| CTR telProdNpMonIfcPPPNCPBCPStConfReqRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.2.3.1.3 | Counter | read-only | Number of Configure Request NCP frames received through the interface number shown in the index. |
| CTR telProdNpMonIfcPPPNCPBCPStConfReqTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.2.3.1.4 | Counter | read-only | Number of Configure Request NCP frames transmitted through the interface number shown in the index. |
| CTR telProdNpMonIfcPPPNCPBCPStConfAckRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.2.3.1.5 | Counter | read-only | Number of Configure Ack NCP frames received through the interface number shown in the index. |
| CTR telProdNpMonIfcPPPNCPBCPStConfAckTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.2.3.1.6 | Counter | read-only | Number of Configure Ack NCP frames transmitted through the interface number shown in the index. |
| CTR telProdNpMonIfcPPPNCPBCPStConfNakRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.2.3.1.7 | Counter | read-only | Number of Configure Nak NCP frames received through the interface number shown in the index. |
| CTR telProdNpMonIfcPPPNCPBCPStConfNakTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.2.3.1.8 | Counter | read-only | Number of Configure Nak NCP frames transmitted through the interface number shown in the index. |
| CTR telProdNpMonIfcPPPNCPBCPStConfRejRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.2.3.1.9 | Counter | read-only | Number of Configure Reject NCP frames received through the interface number shown in the index. |
| CTR telProdNpMonIfcPPPNCPBCPStConfRejTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.2.3.1.10 | Counter | read-only | Number of Configure Reject NCP frames transmitted through the interface number shown in the index. |
| CTR telProdNpMonIfcPPPNCPBCPStTermReqRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.2.3.1.11 | Counter | read-only | Number of Terminate Request NCP frames received through the interface number shown in the index. |
| CTR telProdNpMonIfcPPPNCPBCPStTermReqTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.2.3.1.12 | Counter | read-only | Number of Terminate Request NCP frames transmitted through the interface number shown in the index. |
| CTR telProdNpMonIfcPPPNCPBCPStTermAckRx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.2.3.1.13 | Counter | read-only | Number of Terminate Ack NCP frames received through the interface number shown in the index. |
| CTR telProdNpMonIfcPPPNCPBCPStTermAckTx | 1.3.6.1.4.1.2007.4.1.2.2.2.10.9.2.3.1.14 | Counter | read-only | Number of Terminate Ack NCP frames transmitted through the interface number shown in the index. |
RFC description
SNMP MIB for monitoring Point-to-Point Protocol (PPP) interfaces on TELDAT routers, providing management objects for PPP link control, authentication (PAP/CHAP), and connection status on synchronous/asynchronous serial lines and ISDN links.
Start monitoring Teldat router, WAN/branch (PPP LCP/NCP negotiation status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.