Juniper-UNI-ATM-MIB

All MIBs › Juniper-UNI-ATM-MIB

Organization: Juniper Networks, Inc.

Last Updated: 2005-11-15

Category: ATM, Protocol: ATM, Vendor: Juniper

Description: Juniper Networks MIB for managing ATM User-Network Interface (UNI) parameters on Juniper E-series access platforms.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Juniper-UNI-ATM-MIB?

Juniper-UNI-ATM-MIB is a Juniper Networks enterprise MIB for managing ATM (Asynchronous Transfer Mode) interfaces at the User-Network Interface on JUNOSe E-series access platforms. It exposes an ATM interface table covering ILMI VPI/VCI/VCD values, ILMI poll frequency and administrative state, UNI version, and ATM/AAL5 layering objects. Its monitoring focus is interface/software operational state: juniAtmIfIlmiAdminState shows whether ILMI auto-configuration signaling is administratively enabled on a given ATM circuit, and juniAtmIfIlmiPollFrequency affects how quickly link-status changes on that circuit are detected — both relevant to diagnosing link-layer faults on legacy ATM access lines. It relates to standard ATM MIBs (RFC 2515/2684) and ILMI specifications while being a Juniper-specific implementation. It is typically deployed in legacy DSL/ATM-based broadband access networks using Juniper E-series edge routers, where engineers open the Juniper-UNI-ATM-MIB MIB Browser view to inspect these objects directly.

IPNetwork Monitor allows you to monitor SNMP objects defined in Juniper-UNI-ATM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Juniper E-series router (ATM/DSL broadband access platform)

Monitoring Examples

An operator can poll juniAtmIfTable (juniAtmIfIndex, juniAtmIfLowerIfIndex) to map ATM interfaces to their underlying physical interfaces, then check juniAtmIfIlmiAdminState and juniAtmIfIlmiPollFrequency to confirm ILMI is enabled and polling at the expected interval on a subscriber-facing ATM UNI. An unexpectedly disabled ILMI admin state, or stale juniAtmIfIlmiVpi/juniAtmIfIlmiVci/juniAtmIfIlmiVcd values, would explain why auto-configuration of VPI/VCI on that circuit is failing.

What Can Be Monitored

ATM interface ILMI VPI/VCI/VCD values
ILMI administrative state
ILMI poll frequency
UNI version
ATM-to-physical interface mapping

Imported Objects

From ATM-FORUM-SNMP-M4-MIB

atmfM4VcTestCode	OBJECT-TYPE
atmfM4VcTestId	OBJECT-TYPE
atmfM4VcTestObject	OBJECT-TYPE
atmfM4VcTestResult	OBJECT-TYPE
atmfM4VcTestType	OBJECT-TYPE
atmfM4VpTestCode	OBJECT-TYPE
atmfM4VpTestId	OBJECT-TYPE
atmfM4VpTestObject	OBJECT-TYPE
atmfM4VpTestResult	OBJECT-TYPE
atmfM4VpTestType	OBJECT-TYPE

From ATM-MIB

atmVclVci	OBJECT-TYPE
atmVclVpi	OBJECT-TYPE
atmVplVpi	OBJECT-TYPE

From ATM-TC-MIB

AtmAddr
AtmVcIdentifier
AtmVorXAdminStatus
AtmVpIdentifier

From IF-MIB

InterfaceIndex
InterfaceIndexOrZero
ifIndex	OBJECT-TYPE

From Juniper-MIBs

juniMibs

MODULE-IDENTITY

From Juniper-TC

JuniEnable
JuniInterfaceLocationType
JuniInterfaceLocationValue
JuniNextIfIndex

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Counter64
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-IDENTITY
OBJECT-TYPE
TimeTicks
Unsigned32

From SNMPv2-TC

DisplayString
RowStatus
TEXTUAL-CONVENTION
TimeStamp
TruthValue

How to Use in IPNetwork Monitor

Example using juniAtmIfInCells OID:

Select a Juniper E-series router, ATM/DSL broadband access platform (ATM UNI interfaces) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type juniAtmIfInCells into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The total number of cells received on this major interface. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter64-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
juniAtmMIB	1.3.6.1.4.1.4874.2.2.8			The ATM MIB for the Juniper enterprise.
juniAtmObjects	1.3.6.1.4.1.4874.2.2.8.1
juniAtmIfLayer	1.3.6.1.4.1.4874.2.2.8.1.1
JUN juniAtmNextIfIndex	1.3.6.1.4.1.4874.2.2.8.1.1.1	JuniNextIfIndex	read-only	Coordinate ifIndex value allocation for entries in juniAtmIfTable. A GET of this object returns the next available ifIndex value to be used to create an entry in the associated interface table; or zero, if no valid ifIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously.
juniAtmIfTable	1.3.6.1.4.1.4874.2.2.8.1.1.2		not-accessible	This table contains entries for ATM interfaces present in the system.
juniAtmIfEntry	1.3.6.1.4.1.4874.2.2.8.1.1.2.1		not-accessible	Each entry describes the characteristics of an ATM interface. Creating/deleting entries in this table causes corresponding entries for be created/deleted in ifTable/ifXTable/juniIfTable.
NUM juniAtmIfIndex	1.3.6.1.4.1.4874.2.2.8.1.1.2.1.1	InterfaceIndex	not-accessible	The ifIndex of the ATM interface. When creating entries in this table, suitable values for this object are determined by reading juniAtmNextIfIndex.
ROW juniAtmIfRowStatus	1.3.6.1.4.1.4874.2.2.8.1.1.2.1.2	RowStatus	read-create	Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniAtmIfRowStatus juniAtmIfLowerIfIndex In addition, when creating an entry the following condition must hold: A value for juniAtmIfIndex must have been determined previously, by reading juniAtmNextIfIndex. A corresponding entry in ifTable/ifXTable/juniIfTable is created or destroyed as a result of creating/destroying an entry in this table.
NUM juniAtmIfLowerIfIndex	1.3.6.1.4.1.4874.2.2.8.1.1.2.1.3	InterfaceIndexOrZero	read-create	The ifIndex of an interface over which this ATM interface is to be layered. A value of zero indicates no layering. An implementation may choose to require that a nonzero value be configured at entry creation.
OID juniAtmIfIlmiVpi	1.3.6.1.4.1.4874.2.2.8.1.1.2.1.4	AtmVpIdentifier	read-create	The VPI of the ILMI of a major ATM interface.
OID juniAtmIfIlmiVci	1.3.6.1.4.1.4874.2.2.8.1.1.2.1.5	AtmVcIdentifier	read-create	The VCI of the ILMI of a major ATM interface.
I32 juniAtmIfIlmiVcd	1.3.6.1.4.1.4874.2.2.8.1.1.2.1.6	Integer32	read-create	An integer identifier for the ILMI, used in conjunction with the command-line interface. The value must be unique among VCs configured on the same ATM interface.
I32 juniAtmIfIlmiPollFrequency	1.3.6.1.4.1.4874.2.2.8.1.1.2.1.7	Integer32	read-create	The amount of time in seconds between successive transmissions of ILMI messages on this interface for the purpose of detecting loss of ILMI connectivity. The distinguished value zero disables ILMI connectivity procedures on this interface.
INT juniAtmIfIlmiAdminState	1.3.6.1.4.1.4874.2.2.8.1.1.2.1.8	INTEGER	read-create	The administrative status of ILMI in the ATM interface.
INT juniAtmIfUniVersion	1.3.6.1.4.1.4874.2.2.8.1.1.2.1.9	INTEGER	read-create	Use to specify the User Network Interface (UNI) the router should use when ILMI link auto determination is unsuccesful or ILMI is disabled.
INT juniAtmIfOamCellRxAdminState	1.3.6.1.4.1.4874.2.2.8.1.1.2.1.10	INTEGER	read-create	Use to specify the OAM Cell Receive Administrative state on this interface.
C64 juniAtmIfInCellsEx	1.3.6.1.4.1.4874.2.2.8.1.1.2.1.11	Counter64	read-only	The total number of cells received on this major interface.
C64 juniAtmIfOutCells	1.3.6.1.4.1.4874.2.2.8.1.1.2.1.12	Counter64	read-only	The total number of cells transmitted on this major interface.
I32 juniAtmIfVcCount	1.3.6.1.4.1.4874.2.2.8.1.1.2.1.13	Integer32	read-only	The total number of circuits configured on this interface.
JUN juniAtmIfMapGroup	1.3.6.1.4.1.4874.2.2.8.1.1.2.1.14	JuniAtmNbmaMapNameOrNull	read-create	The NBMA map group this interface is associated with.
JUN juniAtmIfCacAdminState	1.3.6.1.4.1.4874.2.2.8.1.1.2.1.15	JuniEnable	read-create	The administrative staus of CAC on this ATM major interface.
I32 juniAtmIfCacUbrWeight	1.3.6.1.4.1.4874.2.2.8.1.1.2.1.16	Integer32	read-create	The bandwidth associated with every UBR and UBR with PCR connection configured on the ATM major interface. This value is used for CAC computation. The units are kilo-bits per second (kbps).
I32 juniAtmIfCacSubscriptionBandwidth	1.3.6.1.4.1.4874.2.2.8.1.1.2.1.17	Integer32	read-create	The subscribed bandwidth of the ATM major interface. If this value is not specified or set to 0, the effective port bandwidth is used. When a Get operation is performed the current effective bandwidth is returned. The units are kilo-bits per second (kbps).
I32 juniAtmIfCacAvailableBandwidth	1.3.6.1.4.1.4874.2.2.8.1.1.2.1.18	Integer32	read-only	The available bandwidth in Tx direction of the ATM major interface. As connections are added or deleted on the interface, this value is updated. The units are kilo-bits per second (kbps).
I32 juniAtmIfCacAvailableBandwidthRx	1.3.6.1.4.1.4874.2.2.8.1.1.2.1.19	Integer32	read-only	The available bandwidth in Rx direction of the ATM major interface. As connections are added or deleted on the interface, this value is updated. The units are kilo-bits per second (kbps).
INT juniAtmIfE164Autoconversion	1.3.6.1.4.1.4874.2.2.8.1.1.2.1.20	INTEGER	read-create	The status of E164 autoconversion feature in the ATM interface.
INT juniAtmIfE164Gateway	1.3.6.1.4.1.4874.2.2.8.1.1.2.1.21	INTEGER	read-create	The status of E164 gateway feature in the ATM interface.
INT juniAtmIfE164OneToOneAddrTrans	1.3.6.1.4.1.4874.2.2.8.1.1.2.1.22	INTEGER	read-create	The status of E164 one-to-one address translation feature in the ATM interface.
INT juniAtmIfOamCellFilter	1.3.6.1.4.1.4874.2.2.8.1.1.2.1.23	INTEGER	read-create	The type of OAM cells to discard when juniAtmIfOamCellRxAdminState is set to oamCellAdminStateDisabled. The value oamCellFilterAlarm discards received OAM AIS and RDI cells. The value oamCellFilterAll discards all received OAM cells. Note that when juniAtmIfOamCellRxAdminState is set to oamCellAdminStateEnabled, this object has no effect.
U32 juniAtmIfCacUsedBandwidthUpper	1.3.6.1.4.1.4874.2.2.8.1.1.2.1.24	Unsigned32	read-only	The most significant 32 bits of the CAC used bandwidth on the ATM major interface. The least significant 32 bits of the CAC used bandwidth are specified by juniAtmIfCacUsedBandwidthLower.
U32 juniAtmIfCacUsedBandwidthLower	1.3.6.1.4.1.4874.2.2.8.1.1.2.1.25	Unsigned32	read-only	The least significant 32 bits of the CAC used bandwidth on the ATM major interface. The most significant 32 bits of the CAC used bandwidth are specified by juniAtmIfCacUsedBandwidthUpper.
U32 juniAtmIfAssociatedVcClassId	1.3.6.1.4.1.4874.2.2.8.1.1.2.1.26	Unsigned32	read-create	The integer identifier of the ATM VC class associated with this ATM interface. A value for this identifier is determined by locating or creating an ATM VC class name in the juniAtmVcClassNameTable. A value of 0 means no VC class association exists for this interface.
juniAtmPvcStatisticsTable	1.3.6.1.4.1.4874.2.2.8.1.1.3		not-accessible	This table contains statistics for PVC entries.
juniAtmPvcStatisticsEntry	1.3.6.1.4.1.4874.2.2.8.1.1.3.1		not-accessible	Each entry provides statistics on an ATM PVC.
NUM juniAtmPvcStatsIfIndex	1.3.6.1.4.1.4874.2.2.8.1.1.3.1.1	InterfaceIndex	not-accessible	The ifIndex of the ATM interface.
OID juniAtmPvcStatsVpi	1.3.6.1.4.1.4874.2.2.8.1.1.3.1.2	AtmVpIdentifier	not-accessible	The VPI of the ATM VCC used by this ATM interface and PVC.
OID juniAtmPvcStatsVci	1.3.6.1.4.1.4874.2.2.8.1.1.3.1.3	AtmVcIdentifier	not-accessible	The VCI of the ATM VCC used by this ATM interface and PVC.
C64 juniAtmPvcStatsInCells	1.3.6.1.4.1.4874.2.2.8.1.1.3.1.4	Counter64	read-only	Received cells.
C64 juniAtmPvcStatsInCellOctets	1.3.6.1.4.1.4874.2.2.8.1.1.3.1.5	Counter64	read-only	Received cells octets.
C64 juniAtmPvcStatsInPackets	1.3.6.1.4.1.4874.2.2.8.1.1.3.1.6	Counter64	read-only	Received AAL PDUs.
C64 juniAtmPvcStatsInPacketOctets	1.3.6.1.4.1.4874.2.2.8.1.1.3.1.7	Counter64	read-only	Received AAL PDU octets.
C64 juniAtmPvcStatsOutCells	1.3.6.1.4.1.4874.2.2.8.1.1.3.1.8	Counter64	read-only	Transmitted cells.
C64 juniAtmPvcStatsOutCellOctets	1.3.6.1.4.1.4874.2.2.8.1.1.3.1.9	Counter64	read-only	Transmitted cell octets.
C64 juniAtmPvcStatsOutPackets	1.3.6.1.4.1.4874.2.2.8.1.1.3.1.10	Counter64	read-only	Transmitted AAL PDUs.
C64 juniAtmPvcStatsOutPacketOctets	1.3.6.1.4.1.4874.2.2.8.1.1.3.1.11	Counter64	read-only	Transmitted AAL PDU octets.
C32 juniAtmPvcStatsInCellErrors	1.3.6.1.4.1.4874.2.2.8.1.1.3.1.12	Counter32	read-only	Received cells dropped due to errors.
C32 juniAtmPvcStatsinPacketErrors	1.3.6.1.4.1.4874.2.2.8.1.1.3.1.13	Counter32	read-only	Received packets dropped due to errors.
C32 juniAtmPvcStatsOutCellErrors	1.3.6.1.4.1.4874.2.2.8.1.1.3.1.14	Counter32	read-only	Cells not transmitted due to errors.
C32 juniAtmPvcStatsOutPacketErrors	1.3.6.1.4.1.4874.2.2.8.1.1.3.1.15	Counter32	read-only	Packets not transmitted due to errors.
C32 juniAtmPvcStatsInPacketDiscards	1.3.6.1.4.1.4874.2.2.8.1.1.3.1.16	Counter32	read-only	Received packets w/o errors discarded.
C32 juniAtmPvcStatsInPacketOctetDiscards	1.3.6.1.4.1.4874.2.2.8.1.1.3.1.17	Counter32	read-only	Received bytes w/o errors discarded.
C32 juniAtmPvcStatsInPacketUnknownProtocol	1.3.6.1.4.1.4874.2.2.8.1.1.3.1.18	Counter32	read-only	Received packets that are discarded because the interface can not discern or is not configured to support this protocol.
juniAtmVpTunnelTable	1.3.6.1.4.1.4874.2.2.8.1.1.4		not-accessible	This table contains entries for ATM VP Tunnels present in the system.
juniAtmVpTunnelEntry	1.3.6.1.4.1.4874.2.2.8.1.1.4.1		not-accessible	Each entry describes the characteristics of an ATM VP Tunnel.
NUM juniAtmVpTunnelIfIndex	1.3.6.1.4.1.4874.2.2.8.1.1.4.1.1	InterfaceIndex	not-accessible	The ifIndex of the ATM interface. The value of this object is the same as the juniAtmIfIndex object in the juniAtmIfTable. Entries in this table cannot be created unless the underlying ATM interface entry is created first in the juniAtmIfTable.
OID juniAtmVpTunnelVpi	1.3.6.1.4.1.4874.2.2.8.1.1.4.1.2	AtmVpIdentifier	not-accessible	The VPI value for this VP tunnel entry.
I32 juniAtmVpTunnelKbps	1.3.6.1.4.1.4874.2.2.8.1.1.4.1.3	Integer32	read-create	The tunnel rate in kilobits per second (kbps) for this entry.
ROW juniAtmVpTunnelRowStatus	1.3.6.1.4.1.4874.2.2.8.1.1.4.1.4	RowStatus	read-create	Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniAtmVpTunnelRowStatus juniAtmVpTunnelKbps In addition, when creating an entry the following condition must hold: A correponding juniAtmVpTunnelIfIndex value must have been created in the juniAtmIfTable previously.
INT juniAtmVpTunnelServiceCategory	1.3.6.1.4.1.4874.2.2.8.1.1.4.1.5	INTEGER	read-create	The ATM service category for the tunnel.
juniAtmIfCapabilityTable	1.3.6.1.4.1.4874.2.2.8.1.1.5		not-accessible	This table contains entries for ATM interfaces present in the system.
juniAtmIfCapabilityEntry	1.3.6.1.4.1.4874.2.2.8.1.1.5.1		not-accessible	Each entry describes the capabilities of an ATM interface. A management client can use this table to determine differences in the configurable level of support across entries in this table.
NUM juniAtmIfCapabilityIndex	1.3.6.1.4.1.4874.2.2.8.1.1.5.1.1	InterfaceIndex	not-accessible	The ifIndex of the ATM interface. The value of this object is the same as juniAtmIfIndex in the juniAtmIfTable.
T/F juniAtmIfCapabilityTrafficShaping	1.3.6.1.4.1.4874.2.2.8.1.1.5.1.2	TruthValue	read-only	Indicates whether traffic shaping is supported on this interface; true(1) indicates that it is, false(2) indicates that it is not.
T/F juniAtmIfCapabilityOam	1.3.6.1.4.1.4874.2.2.8.1.1.5.1.3	TruthValue	read-only	Indicates whether OAM is supported on this interface; true(1) indicates that it is, false(2) indicates that it is not.
I32 juniAtmIfCapabilityDefaultVcPerVp	1.3.6.1.4.1.4874.2.2.8.1.1.5.1.4	Integer32	read-only	The default number of VCs per VP for this interface.
I32 juniAtmIfCapabilityNumVpiVciBits	1.3.6.1.4.1.4874.2.2.8.1.1.5.1.5	Integer32	read-only	The total range of bits used for constructing VPI/VCI identifiers for this interface.
I32 juniAtmIfCapabilityMaxVcd	1.3.6.1.4.1.4874.2.2.8.1.1.5.1.6	Integer32	read-only	The maximum configurable value for a VCD on this interface.
OID juniAtmIfCapabilityMaxVpi	1.3.6.1.4.1.4874.2.2.8.1.1.5.1.7	AtmVpIdentifier	read-only	The maximum configurable value for a VPI on this interface.
OID juniAtmIfCapabilityMaxVci	1.3.6.1.4.1.4874.2.2.8.1.1.5.1.8	AtmVcIdentifier	read-only	The maximum configurable value for a VCI on this interface.
T/F juniAtmIfCapabilityOamCellFilter	1.3.6.1.4.1.4874.2.2.8.1.1.5.1.9	TruthValue	read-only	Indicates whether OAM cell filter is supported on this interface; true(1) indicates that it is, false(2) indicates that it is not.
juniAtmIfSvcSignallingTable	1.3.6.1.4.1.4874.2.2.8.1.1.6		not-accessible	This table contains entries for extending the juniAtmIfTable for configuring signalling information for switched virtual connection (SVC).
juniAtmIfSvcSignallingEntry	1.3.6.1.4.1.4874.2.2.8.1.1.6.1		not-accessible	Each entry provides configuration parameters for ATM signalling on the interface.
OID juniAtmIfSvcSignallingVpi	1.3.6.1.4.1.4874.2.2.8.1.1.6.1.1	AtmVpIdentifier	read-write	The VPI identifier of the ATM circuit used for signalling for this interface.
OID juniAtmIfSvcSignallingVci	1.3.6.1.4.1.4874.2.2.8.1.1.6.1.2	AtmVcIdentifier	read-write	The VCI identifier of the ATM circuit used for signalling for this interface.
I32 juniAtmIfSvcSignallingVcd	1.3.6.1.4.1.4874.2.2.8.1.1.6.1.3	Integer32	read-write	An integer identifier for the ATM circuit used for signalling on this interface.
ATM juniAtmIfSvcSignallingAdminStatus	1.3.6.1.4.1.4874.2.2.8.1.1.6.1.4	AtmVorXAdminStatus	read-write	The administrative status of signalling on the ATM interface.
juniAtmIfPnniRccTable	1.3.6.1.4.1.4874.2.2.8.1.1.7		not-accessible	This table contains entries for extending the juniAtmIfTable for configuring PNNI RCC information.
juniAtmIfPnniRccEntry	1.3.6.1.4.1.4874.2.2.8.1.1.7.1		not-accessible	Each entry provides configuration parameters for PNNI RCC on the interface.
OID juniAtmIfPnniRccVpi	1.3.6.1.4.1.4874.2.2.8.1.1.7.1.1	AtmVpIdentifier	read-write	The VPI identifier of the ATM circuit used for PNNI RCC on this interface.
OID juniAtmIfPnniRccVci	1.3.6.1.4.1.4874.2.2.8.1.1.7.1.2	AtmVcIdentifier	read-write	The VCI identifier of the ATM circuit used for PNNI RCC on this interface.
I32 juniAtmIfPnniRccVcd	1.3.6.1.4.1.4874.2.2.8.1.1.7.1.3	Integer32	read-write	An integer identifier for the ATM circuit used for PNNI RCC on this interface.
ATM juniAtmIfPnniRccAdminStatus	1.3.6.1.4.1.4874.2.2.8.1.1.7.1.4	AtmVorXAdminStatus	read-write	The administrative status of PNNI on the ATM interface.
juniAtmOamF4FlowEndToEndCfgTable	1.3.6.1.4.1.4874.2.2.8.1.1.8		not-accessible	This table contains entries for F4 OAM end-to-end flows configured.
juniAtmOamF4FlowEndToEndCfgEntry	1.3.6.1.4.1.4874.2.2.8.1.1.8.1		not-accessible	Each entry provides configuration parameters for one F4 OAM end-to-end flow configured for each VPI.
NUM juniAtmOamF4FlowEndToEndIfIndex	1.3.6.1.4.1.4874.2.2.8.1.1.8.1.1	InterfaceIndex	not-accessible	The ifIndex of the ATM interface to configure the F4 OAM end-to-end flow.
I32 juniAtmOamF4FlowEndToEndVpi	1.3.6.1.4.1.4874.2.2.8.1.1.8.1.2	Integer32	not-accessible	Select the VPI for F4 OAM end-to-end flow configuration.
I32 juniAtmOamF4FlowEndToEndLoopbackTimer	1.3.6.1.4.1.4874.2.2.8.1.1.8.1.3	Integer32	read-create	Configure the timer for sending the F4 flow end-to-end loopback OAM cells. Setting this value will enable sending the F4 end cells on the circuit. It is not allowed to set the value to -1 and whenever it is read as -1 that means sending end loopback is not enabled. Setting the loopback timer, other than -1, will enable sending the end cells.
T/F juniAtmOamF4FlowEndToEndCCSink	1.3.6.1.4.1.4874.2.2.8.1.1.8.1.4	TruthValue	read-create	Enable/Disable F4 flow end-to-end continuity check sink end point for this VP.
T/F juniAtmOamF4FlowEndToEndCCSource	1.3.6.1.4.1.4874.2.2.8.1.1.8.1.5	TruthValue	read-create	Enable/Disable F4 flow end-to-end continuity check source end point for this VP.
ROW juniAtmOamF4FlowEndToEndRowStatus	1.3.6.1.4.1.4874.2.2.8.1.1.8.1.6	RowStatus	read-create	Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create/delete an entry in this table, the following entry objects MUST be explicitly configured: juniAtmOamF4FlowEndToEndRowStatus F4 OAM end loopback and CC tests are mutually exclusive, enabling one will disable the other automatically. So, it is not allowed either at the circuit creation time or after the circuit creation to issue a request to enable end-to-end loopback and CC tests simultaneouly. Enabling/disabling CC sink and source is one time operation. To re-enable either CC source and sink in way different to earlier, both has to be disabled from the previous.
juniAtmOamF4FlowSegmentCfgTable	1.3.6.1.4.1.4874.2.2.8.1.1.9		not-accessible	This table contains entries for F4 OAM Segment flows configured.
juniAtmOamF4FlowSegmentCfgEntry	1.3.6.1.4.1.4874.2.2.8.1.1.9.1		not-accessible	Each entry provides configuration parameters for one F4 OAM Segment flow configured for each VPI.
NUM juniAtmOamF4FlowSegmentIfIndex	1.3.6.1.4.1.4874.2.2.8.1.1.9.1.1	InterfaceIndex	not-accessible	The ifIndex of the ATM interface to configure the F4 OAM segment flow.
I32 juniAtmOamF4FlowSegmentVpi	1.3.6.1.4.1.4874.2.2.8.1.1.9.1.2	Integer32	not-accessible	Select the VPI for F4 OAM segment flow configuration.
T/F juniAtmOamF4FlowSegmentCCSink	1.3.6.1.4.1.4874.2.2.8.1.1.9.1.3	TruthValue	read-create	Enable/Disable F4 flow segment continuity check sink end point for this VP.
T/F juniAtmOamF4FlowSegmentCCSource	1.3.6.1.4.1.4874.2.2.8.1.1.9.1.4	TruthValue	read-create	Enable/Disable F4 flow segment continuity check source end point for this VP.
ROW juniAtmOamF4FlowSegmentRowStatus	1.3.6.1.4.1.4874.2.2.8.1.1.9.1.5	RowStatus	read-create	Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create/delete an entry in this table, the following entry objects MUST be explicitly configured: juniAtmOamF4FlowSegmentRowStatus Enabling/disabling CC sink and source is one time operation. To re-enable either CC source and sink in way different to earlier, both has to be disabled from the previous. F4 OAM segment loopback test is not supported.
juniAtmVpDescrTable	1.3.6.1.4.1.4874.2.2.8.1.1.10		not-accessible	This table contains entries for ATM VP Description present in the system. The user can configure a description of up to 32 characters for every VP in the ATM interface. A row exists for every VP on the ATM interface. These rows get created as soon as the ATM major interface created.
juniAtmVpDescrEntry	1.3.6.1.4.1.4874.2.2.8.1.1.10.1		not-accessible	Each entry contains the description of the VP.
STR juniAtmVpDescription	1.3.6.1.4.1.4874.2.2.8.1.1.10.1.1	SnmpAdminString	read-write	The description for this VP. The default value of this object is null string.
juniAtmF4FlowOamEndToEndStatsTable	1.3.6.1.4.1.4874.2.2.8.1.1.11		not-accessible	This table contains entries for F4 flow EndToEnd OAM circuits stats.
juniAtmF4FlowOamEndToEndStatsEntry	1.3.6.1.4.1.4874.2.2.8.1.1.11.1		not-accessible	Each entry provides stats for one F4 OAM circuit for each VPI.
C32 juniAtmF4FlowInOamEndAisCells	1.3.6.1.4.1.4874.2.2.8.1.1.11.1.1	Counter32	read-only	Received end-to-end OAM F4 AIS cells.
C32 juniAtmF4FlowInOamEndRdiCells	1.3.6.1.4.1.4874.2.2.8.1.1.11.1.2	Counter32	read-only	Received end-to-end OAM F4 RDI cells.
C32 juniAtmF4FlowInOamEndCCCells	1.3.6.1.4.1.4874.2.2.8.1.1.11.1.3	Counter32	read-only	Received end-to-end OAM F4 CC cells.
C32 juniAtmF4FlowInOamEndCCActDeActCells	1.3.6.1.4.1.4874.2.2.8.1.1.11.1.4	Counter32	read-only	Received end-to-end OAM F4 activation/de-activation cells.
C32 juniAtmF4FlowInOamEndLoopbackCells	1.3.6.1.4.1.4874.2.2.8.1.1.11.1.5	Counter32	read-only	Total received OAM F4 end-to-end loopback cells. Aggregate of juniAtmF4FlowEndToEndInLoopbackCmds and juniAtmF4FlowEndToEndInLoopbackRsps
C32 juniAtmF4FlowOutEndRdiCells	1.3.6.1.4.1.4874.2.2.8.1.1.11.1.6	Counter32	read-only	Transmitted end-to-end OAM F4 RDI cells.
C32 juniAtmF4FlowOutEndCCCells	1.3.6.1.4.1.4874.2.2.8.1.1.11.1.7	Counter32	read-only	Transmitted end-to-end OAM F4 CC cells.
C32 juniAtmF4FlowOutEndCCActDeActCells	1.3.6.1.4.1.4874.2.2.8.1.1.11.1.8	Counter32	read-only	Transmitted end-to-end OAM F4 activation/de-activation cells.
C32 juniAtmF4FlowOutEndToEndLoopbackCells	1.3.6.1.4.1.4874.2.2.8.1.1.11.1.9	Counter32	read-only	Total transmitted OAM F4 end-to-end loopback cells. Aggregate of juniAtmF4FlowEndToEndOutLoopbackCmds and juniAtmF4FlowEndToEndOutLoopbackRsps
I32 juniAtmF4FlowEndActualLoopbackFreq	1.3.6.1.4.1.4874.2.2.8.1.1.11.1.10	Integer32	read-only	Actual end-to-end loopback Frequecy calculated for OAM cells transmission.
TIK juniAtmF4FlowEndLastTimeChanged	1.3.6.1.4.1.4874.2.2.8.1.1.11.1.11	TimeTicks	read-only	Last time end-to-end F4 OAM flow got changed.
INT juniAtmF4FlowOamEndVpOperationState	1.3.6.1.4.1.4874.2.2.8.1.1.11.1.12	INTEGER	read-only	Represents the F4 end-to-end OAM flow VP operation states. It can take one of the following operational state values: vcAisState - AIS cell received or underlying physical layer reporting transmission path AIS. vcRdiState - RDI cell received. vcDownRetry - OAM loopback failed, using retry frequency to verify that the VC is really down. vcUpRetry - OAM loopback successful, using retry frequency to verify that the VC is really up. vcUp - OAM loopback successful after up retry verification. vcDown - OAM loopback failed after down retry verification. vcNotManaged - No verification via loopback cells being performed. vpAisState - State when F4 AIS cell is received. vpRdiState - State when F4 RDI cell is received. vcInVpRdiState - The data vc is down as a result of VP failure thorugh F4 Rdi oam cell. vcInVpAisState - The data vc is down as a result of VP failure through F4 Ais oam cell. vcSegmentAisState - Segment AIS cell received. vcSegRdiState - Segment RDI cell received.
INT juniAtmF4FlowOamEndVpAdminState	1.3.6.1.4.1.4874.2.2.8.1.1.11.1.13	INTEGER	read-only	End-to-end VP admin state.
C32 juniAtmF4FlowEndInOamCells	1.3.6.1.4.1.4874.2.2.8.1.1.11.1.14	Counter32	read-only	Received end-to-end OAM F4 loopback cells.
C32 juniAtmF4FlowEndOutOamCells	1.3.6.1.4.1.4874.2.2.8.1.1.11.1.15	Counter32	read-only	Transmitted end-to-end OAM F4 loopback cells.
C32 juniAtmF4FlowEndInOamCellsDropped	1.3.6.1.4.1.4874.2.2.8.1.1.11.1.16	Counter32	read-only	Received end-to-end OAM cells that were dropped.
C32 juniAtmF4FlowEndToEndInLoopbackCmds	1.3.6.1.4.1.4874.2.2.8.1.1.11.1.17	Counter32	read-only	Received OAM F4 end-to-end loopback commands.
C32 juniAtmF4FlowEndToEndInLoopbackRsps	1.3.6.1.4.1.4874.2.2.8.1.1.11.1.18	Counter32	read-only	Received OAM F4 end-to-end loopback responses.
C32 juniAtmF4FlowEndToEndOutLoopbackCmds	1.3.6.1.4.1.4874.2.2.8.1.1.11.1.19	Counter32	read-only	Transmitted OAM F4 end-to-end loopback commands.
C32 juniAtmF4FlowEndToEndOutLoopbackRsps	1.3.6.1.4.1.4874.2.2.8.1.1.11.1.20	Counter32	read-only	Transmitted OAM F4 end-to-end loopback responses.
juniAtmF4FlowOamSegmentStatsTable	1.3.6.1.4.1.4874.2.2.8.1.1.12		not-accessible	This table contains entries for F4 flow Segment OAM circuits stats.
juniAtmF4FlowOamSegmentStatsEntry	1.3.6.1.4.1.4874.2.2.8.1.1.12.1		not-accessible	Each entry provides stats for one F4 OAM circuit for each VPI.
C32 juniAtmF4FlowInOamSegmentAisCells	1.3.6.1.4.1.4874.2.2.8.1.1.12.1.1	Counter32	read-only	Received end-to-end OAM F4 AIS cells.
C32 juniAtmF4FlowInOamSegmentRdiCells	1.3.6.1.4.1.4874.2.2.8.1.1.12.1.2	Counter32	read-only	Received end-to-end OAM F4 RDI cells.
C32 juniAtmF4FlowInOamSegmentCCCells	1.3.6.1.4.1.4874.2.2.8.1.1.12.1.3	Counter32	read-only	Received end-to-end OAM F4 CC cells.
C32 juniAtmF4FlowInOamSegmentCCActDeActCells	1.3.6.1.4.1.4874.2.2.8.1.1.12.1.4	Counter32	read-only	Received end-to-end OAM F4 activation/de-activation cells.
C32 juniAtmF4FlowInOamSegmentLoopbackCells	1.3.6.1.4.1.4874.2.2.8.1.1.12.1.5	Counter32	read-only	Total received OAM F4 segment loopback cells. Aggregate of juniAtmF4FlowSegmentInLoopbackCmds and juniAtmF4FlowSegmentInLoopbackRsps
C32 juniAtmF4FlowOutSegmentRdiCells	1.3.6.1.4.1.4874.2.2.8.1.1.12.1.6	Counter32	read-only	Transmitted end-to-end OAM F4 RDI cells.
C32 juniAtmF4FlowOutSegmentCCCells	1.3.6.1.4.1.4874.2.2.8.1.1.12.1.7	Counter32	read-only	Transmitted end-to-end OAM F4 CC cells.
C32 juniAtmF4FlowOutSegmentCCActDeActCells	1.3.6.1.4.1.4874.2.2.8.1.1.12.1.8	Counter32	read-only	Transmitted end-to-end OAM F4 activation/de-activation cells.
C32 juniAtmF4FlowOutSegmentLoopbackCells	1.3.6.1.4.1.4874.2.2.8.1.1.12.1.9	Counter32	read-only	Total transmitted OAM F4 segment loopback cells. Aggregate of juniAtmF4FlowSegmentOutLoopbackCmds and juniAtmF4FlowSegmentOutLoopbackRsps
TIK juniAtmF4FlowSegmentLastTimeChanged	1.3.6.1.4.1.4874.2.2.8.1.1.12.1.10	TimeTicks	read-only	Last time end-to-end F4 OAM flow got changed.
INT juniAtmF4FlowOamSegmentVpOperationState	1.3.6.1.4.1.4874.2.2.8.1.1.12.1.11	INTEGER	read-only	Represents the F4 end-to-end OAM flow VP operation states. It can take one of the following operational state values: vcAisState - AIS cell received or underlying physical layer reporting transmission path AIS. vcRdiState - RDI cell received. vcDownRetry - OAM loopback failed, using retry frequency to verify that the VC is really down. vcUpRetry - OAM loopback successful, using retry frequency to verify that the VC is really up. vcUp - OAM loopback successful after up retry verification. vcDown - OAM loopback failed after down retry verification. vcNotManaged - No verification via loopback cells being performed. vpAisState - State when F4 AIS cell is received. vpRdiState - State when F4 RDI cell is received. vcInVpRdiState - The data vc is down as a result of VP failure thorugh F4 Rdi oam cell. vcInVpAisState - The data vc is down as a result of VP failure through F4 Ais oam cell. vcSegmentAisState - Segment AIS cell received. vcSegRdiState - Segment RDI cell received.
INT juniAtmF4FlowOamSegmentVpAdminState	1.3.6.1.4.1.4874.2.2.8.1.1.12.1.12	INTEGER	read-only	Segment VP admin state.
C32 juniAtmF4FlowSegmentInOamCells	1.3.6.1.4.1.4874.2.2.8.1.1.12.1.13	Counter32	read-only	Received end-to-end OAM F4 loopback cells.
C32 juniAtmF4FlowSegmentOutOamCells	1.3.6.1.4.1.4874.2.2.8.1.1.12.1.14	Counter32	read-only	Transmitted end-to-end OAM F4 loopback cells.
C32 juniAtmF4FlowSegmentInOamCellsDropped	1.3.6.1.4.1.4874.2.2.8.1.1.12.1.15	Counter32	read-only	Received end-to-end OAM cells that were dropped.
C32 juniAtmF4FlowSegmentInLoopbackCmds	1.3.6.1.4.1.4874.2.2.8.1.1.12.1.16	Counter32	read-only	Received OAM F4 segment loopback commands.
C32 juniAtmF4FlowSegmentInLoopbackRsps	1.3.6.1.4.1.4874.2.2.8.1.1.12.1.17	Counter32	read-only	Received OAM F4 segment loopback responses.
C32 juniAtmF4FlowSegmentOutLoopbackCmds	1.3.6.1.4.1.4874.2.2.8.1.1.12.1.18	Counter32	read-only	Transmitted OAM F4 segment loopback commands.
C32 juniAtmF4FlowSegmentOutLoopbackRsps	1.3.6.1.4.1.4874.2.2.8.1.1.12.1.19	Counter32	read-only	Transmitted OAM F4 segment loopback responses.
juniAtmMartiniTimeoutTimerTable	1.3.6.1.4.1.4874.2.2.8.1.1.13		not-accessible	This table contains entries for ATM Martini cell aggregation timeout detection. The user can configure timeout values for three timers. A row exists for every separate timer supported. These rows get created as soon as the ERX system comes up.
juniAtmMartiniTimeoutTimerEntry	1.3.6.1.4.1.4874.2.2.8.1.1.13.1		not-accessible	Each entry contains the timeout value of ATM Martini cell aggregation timer.
INT juniAtmMartiniTimeoutTimerIndex	1.3.6.1.4.1.4874.2.2.8.1.1.13.1.1	INTEGER	not-accessible	The ATM Martini cell aggregation timeout timer identifier.
I32 juniAtmMartiniTimeoutTimerValue	1.3.6.1.4.1.4874.2.2.8.1.1.13.1.2	Integer32	read-write	The ATM Martini cell aggregation timeout timer value in microseconds.
juniAtmVpStatsTable	1.3.6.1.4.1.4874.2.2.8.1.1.14		not-accessible	This table contains entries for ATM VP statistics present in the system. A row exists for every VP on the ATM interface. These rows get created as soon as the ATM major interface created.
juniAtmVpStatsEntry	1.3.6.1.4.1.4874.2.2.8.1.1.14.1		not-accessible	Each entry contain the VP statistics.
NUM juniAtmVpStatsIfIndex	1.3.6.1.4.1.4874.2.2.8.1.1.14.1.1	InterfaceIndex	not-accessible	The ifIndex of the ATM interface.
OID juniAtmVpStatsVpi	1.3.6.1.4.1.4874.2.2.8.1.1.14.1.2	AtmVpIdentifier	not-accessible	The VPI value of the virtual path for which statistics are retrieved.
C64 juniAtmVpStatsInCells	1.3.6.1.4.1.4874.2.2.8.1.1.14.1.3	Counter64	read-only	Received cells.
C64 juniAtmVpStatsInPackets	1.3.6.1.4.1.4874.2.2.8.1.1.14.1.4	Counter64	read-only	Received AAL5 PDUs.
C64 juniAtmVpStatsInPacketOctets	1.3.6.1.4.1.4874.2.2.8.1.1.14.1.5	Counter64	read-only	Received AAL5 PDU octets.
C64 juniAtmVpStatsOutCells	1.3.6.1.4.1.4874.2.2.8.1.1.14.1.6	Counter64	read-only	Transmitted cells.
C64 juniAtmVpStatsOutPackets	1.3.6.1.4.1.4874.2.2.8.1.1.14.1.7	Counter64	read-only	Transmitted AAL5 PDUs
C64 juniAtmVpStatsOutPacketOctets	1.3.6.1.4.1.4874.2.2.8.1.1.14.1.8	Counter64	read-only	Transmitted AAL5 PDU octets.
C32 juniAtmVpStatsInPacketErrors	1.3.6.1.4.1.4874.2.2.8.1.1.14.1.9	Counter32	read-only	Received packets dropped due to errors.
C32 juniAtmVpStatsOutPacketErrors	1.3.6.1.4.1.4874.2.2.8.1.1.14.1.10	Counter32	read-only	Packets not transmitted due to errors.
C32 juniAtmVpStatsInPacketDiscards	1.3.6.1.4.1.4874.2.2.8.1.1.14.1.11	Counter32	read-only	Received packets without errors discarded.
C32 juniAtmVpStatsInPacketOctetDiscards	1.3.6.1.4.1.4874.2.2.8.1.1.14.1.12	Counter32	read-only	Received bytes without errors discarded.
C32 juniAtmVpStatsInPacketUnknownProtocol	1.3.6.1.4.1.4874.2.2.8.1.1.14.1.13	Counter32	read-only	Received packets that are discarded because the interface can not discern or is not configured to support this protocol.
C32 juniAtmVpStatsCrcErrors	1.3.6.1.4.1.4874.2.2.8.1.1.14.1.14	Counter32	read-only	Received packets that are discarded because of check sum erros
C32 juniAtmVpStatsSarTimeouts	1.3.6.1.4.1.4874.2.2.8.1.1.14.1.15	Counter32	read-only	Received packets that are discarded because of SAR timeout
C32 juniAtmVpStatsOverSizedPackets	1.3.6.1.4.1.4874.2.2.8.1.1.14.1.16	Counter32	read-only	Over sized packets that are received on this VP.
juniAtmAal5IfLayer	1.3.6.1.4.1.4874.2.2.8.1.2
JUN juniAtmAal5NextIfIndex	1.3.6.1.4.1.4874.2.2.8.1.2.1	JuniNextIfIndex	read-only	Coordinate ifIndex value allocation for entries in juniAtmAal5IfTable. A GET of this object returns the next available ifIndex value to be used to create an entry in the associated interface table; or zero, if no valid ifIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously.
juniAtmAal5IfTable	1.3.6.1.4.1.4874.2.2.8.1.2.2		not-accessible	This table contains entries for ATM AAL5 interfaces present in the system.
juniAtmAal5IfEntry	1.3.6.1.4.1.4874.2.2.8.1.2.2.1		not-accessible	Each entry describes the characteristics of an ATM AAL5 interface. Creating/deleting entries in this table causes corresponding entries for be created/deleted in ifTable/ifXTable/juniIfTable.
NUM juniAtmAal5IfIndex	1.3.6.1.4.1.4874.2.2.8.1.2.2.1.1	InterfaceIndex	not-accessible	The ifIndex of the ATM AAL5 interface. When creating entries in this table, suitable values for this object are determined by reading juniAtmAal5NextIfIndex.
ROW juniAtmAal5IfRowStatus	1.3.6.1.4.1.4874.2.2.8.1.2.2.1.2	RowStatus	read-create	Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniAtmAal5IfRowStatus juniAtmAal5IfLowerIfIndex In addition, when creating an entry the following condition must hold: A value for juniAtmAal5IfIndex must have been determined previously, by reading juniAtmAal5NextIfIndex. A corresponding entry in ifTable/ifXTable/juniIfTable is created or destroyed as a result of creating/destroying an entry in this table.
NUM juniAtmAal5IfLowerIfIndex	1.3.6.1.4.1.4874.2.2.8.1.2.2.1.3	InterfaceIndexOrZero	read-create	The ifIndex of an ATM interface over which this ATM AAL5 interface is to be layered. A value of zero indicates no layering. An implementation may choose to require that a nonzero value be configured at entry creation.
juniAtmBulkCircuitsNameTable	1.3.6.1.4.1.4874.2.2.8.1.2.3		not-accessible	The entries in this table provide mappings of ATM bulk virtual circuit range names to local integer identifiers for those profiles. These integers are used as indexes into other MIB tables containing profile configuration parameters associated with the same profile name.
juniAtmBulkCircuitsNameEntry	1.3.6.1.4.1.4874.2.2.8.1.2.3.1		not-accessible	A mapping of a ATM bulk virtual circuit range name to an integer identifier for that name.
NUM juniAtmBulkCircuitsNameAal5IfIndex	1.3.6.1.4.1.4874.2.2.8.1.2.3.1.1	InterfaceIndex	not-accessible	The ifIndex of the ATM AAL5 interface.
STR juniAtmBulkCircuitsNameName	1.3.6.1.4.1.4874.2.2.8.1.2.3.1.2	DisplayString	not-accessible	The ATM bulk virtual circuit range name uniquely identifying this entry.
ROW juniAtmBulkCircuitsNameRowStatus	1.3.6.1.4.1.4874.2.2.8.1.2.3.1.3	RowStatus	read-create	Controls creation/deletion of entries in this table. Only the values 'createAndGo' and 'destroy' may be SET. Creating an entry in this table creates corresponding entry in juniAtmBulkCircuitsIdTable. Deleting an entry in this table deletes corresponding entries in juniAtmBulkCircuitsIdTable, juniAtmBulkCircuitsTable and juniAtmProfileOverrideAssignIfCircuitTable.
U32 juniAtmBulkCircuitsNameId	1.3.6.1.4.1.4874.2.2.8.1.2.3.1.4	Unsigned32	read-only	The integer identifier associated with this ATM bulk virtual circuit range name. This value of this identifier is assigned by the device when an entry in this table is created.
juniAtmBulkCircuitsIdTable	1.3.6.1.4.1.4874.2.2.8.1.2.4		not-accessible	Provides inverse mapping of ATM bulk virtual circuit IDs to ATM bulk virtual circuit names.
juniAtmBulkCircuitsIdEntry	1.3.6.1.4.1.4874.2.2.8.1.2.4.1		not-accessible	A mapping of an integer identifier to a ATM bulk virtual circuit name.
NUM juniAtmBulkCircuitsIdAal5IfIndex	1.3.6.1.4.1.4874.2.2.8.1.2.4.1.1	InterfaceIndex	not-accessible	The ifIndex of the ATM AAL5 interface.
U32 juniAtmBulkCircuitsIdId	1.3.6.1.4.1.4874.2.2.8.1.2.4.1.2	Unsigned32	not-accessible	The integer identifier associated with this ATM bulk virtual circuit name.
STR juniAtmBulkCircuitsIdName	1.3.6.1.4.1.4874.2.2.8.1.2.4.1.3	DisplayString	read-only	The ATM bulk virtual circuit name having the associated identifier.
U32 juniAtmBulkCircuitsIdNextInstance	1.3.6.1.4.1.4874.2.2.8.1.2.4.1.4	Unsigned32	read-only	The next available instance value for juniAtmBulkCircuitsEntry.
juniAtmBulkCircuitsTable	1.3.6.1.4.1.4874.2.2.8.1.2.5		not-accessible	This table contains bulk virtual circuit range parameters.
juniAtmBulkCircuitsEntry	1.3.6.1.4.1.4874.2.2.8.1.2.5.1		not-accessible	Each entry describes the characteristics of VC range.
NUM juniAtmBulkCircuitsAal5IfIndex	1.3.6.1.4.1.4874.2.2.8.1.2.5.1.1	InterfaceIndex	not-accessible	The ifIndex of the ATM AAL5 interface on which this bulk virtual circuit sub-range is created.
U32 juniAtmBulkCircuitsId	1.3.6.1.4.1.4874.2.2.8.1.2.5.1.2	Unsigned32	not-accessible	The integer identifier associated with this ATM bulk virtual circuit name.
U32 juniAtmBulkCircuitsInstance	1.3.6.1.4.1.4874.2.2.8.1.2.5.1.3	Unsigned32	not-accessible	The unique identifier of the ATM bulk virtual circuit sub-range.
ROW juniAtmBulkCircuitsRowStatus	1.3.6.1.4.1.4874.2.2.8.1.2.5.1.4	RowStatus	read-create	Controls creation/deletion of entries in this table. Only the values 'createAndGo' and 'destroy' may be SET. Since none of the VPI/VCI minimum and maximum values have default values, all these values must be specified before setting RowStatus to 'createAndGo'. The VPI/VCI minimum and maximum values can only be configured upon creation. Deleting an entry in this table deletes corresponding entries in juniAtmProfileOverrideAssignIfCircuitTable.
OID juniAtmBulkCircuitsMinVpi	1.3.6.1.4.1.4874.2.2.8.1.2.5.1.5	AtmVpIdentifier	read-create	The minimum value of VPI for this circuit sub-range. This value must be less than or equal to the value of juniAtmBulkCircuitsMaxVpi.
OID juniAtmBulkCircuitsMaxVpi	1.3.6.1.4.1.4874.2.2.8.1.2.5.1.6	AtmVpIdentifier	read-create	The maximum value of VPI for this cicuit sub-range. This value must be equal to or greater than the value of juniAtmBulkCircuitsMinVpi.
OID juniAtmBulkCircuitsMinVci	1.3.6.1.4.1.4874.2.2.8.1.2.5.1.7	AtmVcIdentifier	read-create	The minimum value of VCI for this circuit sub-range. This value must be less than or equal to the value of juniAtmBulkCircuitsMaxVci.
OID juniAtmBulkCircuitsMaxVci	1.3.6.1.4.1.4874.2.2.8.1.2.5.1.8	AtmVcIdentifier	read-create	The maximum value of VCI for this circuit sub-range. This value must be equal to or greater than the value of juniAtmBulkCircuitsMinVci.
JUN juniAtmBulkCircuitsAdminState	1.3.6.1.4.1.4874.2.2.8.1.2.5.1.9	JuniEnable	read-create	The administrative status of this circuit sub-range.
juniAtmProfileOverrideAssignIfCircuitTable	1.3.6.1.4.1.4874.2.2.8.1.2.6		not-accessible	Table providing overriding profile assignment to a circuit configured as part of bulk-configuration. Circuit is identified by interface index and vpi, vci. The entries in this table specify which profile to use when creating and configuring a dynamic interface above a circuit specified by vpi and vci. This entry is effective when the circuit specified by juniAtmProfileOverrideAssignIfCircuitAal5Index, juniAtmProfileOverrideAssignIfCircuitRangeId, juniAtmProfileOverrideAssignIfCircuitVpi, juniAtmProfileOverrideAssignIfCircuitVci is part of bulk-configuration.
juniAtmProfileOverrideAssignIfCircuitEntry	1.3.6.1.4.1.4874.2.2.8.1.2.6.1		not-accessible	An assignment of a profile to a circuit configured as part of bulk-configuration on an AAL5 interface.
NUM juniAtmProfileOverrideAssignIfCircuitAal5Index	1.3.6.1.4.1.4874.2.2.8.1.2.6.1.1	InterfaceIndex	not-accessible	The ifIndex of the AAL5 interface to which the profile is assigned.
U32 juniAtmProfileOverrideAssignIfCircuitRangeId	1.3.6.1.4.1.4874.2.2.8.1.2.6.1.2	Unsigned32	not-accessible	The integer identifier associated with the ATM bulk circuit configuration.
OID juniAtmProfileOverrideAssignIfCircuitVpi	1.3.6.1.4.1.4874.2.2.8.1.2.6.1.3	AtmVpIdentifier	not-accessible	The VPI value of the circuit to which the profile is assigned.
OID juniAtmProfileOverrideAssignIfCircuitVci	1.3.6.1.4.1.4874.2.2.8.1.2.6.1.4	AtmVcIdentifier	not-accessible	The VCI value of the circuit to which the profile is assigned.
ROW juniAtmProfileOverrideAssignIfCircuitRowStatus	1.3.6.1.4.1.4874.2.2.8.1.2.6.1.5	RowStatus	read-create	Controls creation/deletion of entries in this table. Only the values 'createAndGo' and 'destroy' may be SET. Since the VPI, VCI and profileId values do not have any default values, all these values must be specified before setting RowStatus to 'createAndGo'. The VPI, VCI and profileId values can only be configured upon creation. None of these values can be modified except by deleting the entry.
U32 juniAtmProfileOverrideAssignIfCircuitProfileId	1.3.6.1.4.1.4874.2.2.8.1.2.6.1.6	Unsigned32	read-create	The ID of the profile assigned to the circuit configured as part of bulk-configuration. Circuit is identified by interface index and vpi, vci.
INT juniAtmProfileOverrideAssignIfCircuitOperStatus	1.3.6.1.4.1.4874.2.2.8.1.2.6.1.7	INTEGER	read-only	The operational status of the profile override assignment identified by this entry. It returns inactive(0), if a static ATM circuit with identical VPI/VCI values is present on the same ATM interface. In this case, this profile override will not be used to configure upper dynamic interfaces. It returns active(1), if no static ATM circuit with identical VPI/VCI values is present on the same ATM interface. In this case, this profile override will be used to configure upper dynamic interfaces.
juniAtmSubIfLayer	1.3.6.1.4.1.4874.2.2.8.1.3
JUN juniAtmSubIfNextIfIndex	1.3.6.1.4.1.4874.2.2.8.1.3.1	JuniNextIfIndex	read-only	Coordinate ifIndex value allocation for entries in juniAtmSubIfTable. A GET of this object returns the next available ifIndex value to be used to create an entry in the associated interface table; or zero, if no valid ifIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously.
juniAtmSubIfTable	1.3.6.1.4.1.4874.2.2.8.1.3.2		not-accessible	This table contains entries for ATM Subinterfaces present in the system.
juniAtmSubIfEntry	1.3.6.1.4.1.4874.2.2.8.1.3.2.1		not-accessible	Each entry describes the characteristics of an ATM Subinterface. Creating/deleting entries in this table causes corresponding entries for be created/deleted in ifTable/ifXTable/juniIfTable.
NUM juniAtmSubIfIndex	1.3.6.1.4.1.4874.2.2.8.1.3.2.1.1	InterfaceIndex	not-accessible	The ifIndex of the ATM Subinterface. When creating entries in this table, suitable values for this object are determined by reading juniAtmSubNextIfIndex.
ROW juniAtmSubIfRowStatus	1.3.6.1.4.1.4874.2.2.8.1.3.2.1.2	RowStatus	read-create	Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniAtmSubIfRowStatus juniAtmSubIfLowerIndex In addition, when creating an entry the following condition must hold: A value for juniAtmSubIfIndex must have been determined previously, by reading juniAtmSubIfNextIfIndex. A corresponding entry in ifTable/ifXTable/juniIfTable is created or destroyed as a result of creating/destroying an entry in this table.
I32 juniAtmSubIfDistinguisher	1.3.6.1.4.1.4874.2.2.8.1.3.2.1.3	Integer32	read-create	An integer identifier for the subinterface, used in conjunction with the command-line interface. It is provided here for cross-reference purposes only. The value must be unique among subinterfaces configured on the same underlying ATM adaptation layer. The upper bound for the value is further constrained to be identical with the maximum number of subinterfaces supported by the lower interface. If this object is not configured, a value will be allocated internally and can be queried after table entry creation has succeeded.
NUM juniAtmSubIfLowerIfIndex	1.3.6.1.4.1.4874.2.2.8.1.3.2.1.4	InterfaceIndexOrZero	read-create	The ifIndex of an ATM AAL5 interface over which this ATM subinterface is to be layered. A value of zero indicates no layering. An implementation may choose to require that a nonzero value be configured at entry creation.
T/F juniAtmSubIfNbma	1.3.6.1.4.1.4874.2.2.8.1.3.2.1.5	TruthValue	read-create	The NBMA administrative setting. Setting this value of this object to true(1) will enable multipoint access on this interface. Setting the value to false(2), will enable point to point access on this interface.
ATM juniAtmSubIfAddress	1.3.6.1.4.1.4874.2.2.8.1.3.2.1.6	AtmAddr	read-create	Specifies the local ATM NSAP address of the circuit. A GET operation returns a full 20-octet NSAP. A SET operation only requires 7 octets, since the prefix can be implied.
I32 juniAtmSubIfMtu	1.3.6.1.4.1.4874.2.2.8.1.3.2.1.7	Integer32	read-create	The size of the largest packet which can be sent/received on the interface, specified in octets.
I32 juniAtmSubIfAdvisoryRxSpeed	1.3.6.1.4.1.4874.2.2.8.1.3.2.1.8	Integer32	read-create	Advisory receive speed, in kilobits per second (kbps), of this subinterface. This object has no impact on forwarding performance but may be used as a hint for underlying circuit receive speed.
I32 juniAtmSubIfMartiniMaxCellsPerPacket	1.3.6.1.4.1.4874.2.2.8.1.3.2.1.9	Integer32	read-create	The number of cells that can be aggregated in a single ATM Martini packet in cell-relay mode.
I32 juniAtmSubIfMartiniTimeoutTimerId	1.3.6.1.4.1.4874.2.2.8.1.3.2.1.10	Integer32	read-create	The timer identifier used to abandon cell aggregation when no cells are supplied for transmission in ATM Martini cell-relay mode.
U32 juniAtmSubIfAssociatedVcClassId	1.3.6.1.4.1.4874.2.2.8.1.3.2.1.11	Unsigned32	read-create	The integer identifier of the ATM VC class associated with this ATM sub interface. A value for this identifier is determined by locating or creating an ATM VC class name in the juniAtmVcClassNameTable. A value of 0 means no VC class association exists for this interface.
juniAtmSubIfVccTable	1.3.6.1.4.1.4874.2.2.8.1.3.3		not-accessible	This table contains entries for ATM VCCs configured on ATM subinterfaces present in the system. An implementation may constrain the number of VCCs permitted to be configured per ATM Subinterface; in particular, an implementation may restrict each ATM Subinterface to have a single VCC. Attributes in this entry can only be configured at entry creation, and remain fixed for the lifetime of the entry.
juniAtmSubIfVccEntry	1.3.6.1.4.1.4874.2.2.8.1.3.3.1		not-accessible	Each entry describes the characteristics of an ATM subinterface VCC.
OID juniAtmSubIfVccVpi	1.3.6.1.4.1.4874.2.2.8.1.3.3.1.1	AtmVpIdentifier	not-accessible	The VPI of the ATM VCC used by this subinterface.
OID juniAtmSubIfVccVci	1.3.6.1.4.1.4874.2.2.8.1.3.3.1.2	AtmVcIdentifier	not-accessible	The VCI of the ATM VCC used by this subinterface.
ROW juniAtmSubIfVccRowStatus	1.3.6.1.4.1.4874.2.2.8.1.3.3.1.3	RowStatus	read-create	Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniAtmSubIfVccRowStatus In addition, when creating an entry the following conditions must hold: The ATM Subinterface identified by juniAtmSubIfIndex must exist. A positive value configured for juniAtmSubIfVccVcd must not already be assigned to an existing VCC. For each value of juniAtmSubIfVccServiceCategory, additional dependent objects in the entry require configuration as identified here: juniAtmSubIfVccServiceCategory Requires configuration of: ------------------------------------------------------------ ubr ubrPcr juniAtmSubIfVccPcr nrtVbr juniAtmSubIfVccPcr juniAtmSubIfVccScr juniAtmSubIfVccMbs cbr juniAtmSubIfVccPcr rtVbr juniAtmSubIfVccPcr juniAtmSubIfVccScr juniAtmSubIfVccMbs ------------------------------------------------------------ Attributes in this entry can only be configured at entry creation, and remain fixed for the lifetime of the entry.
I32 juniAtmSubIfVccVcd	1.3.6.1.4.1.4874.2.2.8.1.3.3.1.4	Integer32	read-create	An integer identifier for the circuit, used in conjunction with the command-line interface. It is provided here for cross-reference purposes only. The value must be unique among VCCs configured on the same underlying ATM interface. If this object is not configured, or is configured with a value of zero, a value will be allocated internally and can be queried after table entry creation has succeeded.
INT juniAtmSubIfVccType	1.3.6.1.4.1.4874.2.2.8.1.3.3.1.5	INTEGER	read-create	Specifies the encapsulation used by the circuit to carry IP datagrams. Encapsulations are as specified in RFC1483 Multiprotocol Interconnect over ATM. The 'autoconfig' value will recognize both VcMux and LLC formats. The 'aal5' and 'aal0' values are used for encapsulation methods for transport of ATM frames and cells over IP and MPLS networks when no encapsulation method is specified.
INT juniAtmSubIfVccServiceCategory	1.3.6.1.4.1.4874.2.2.8.1.3.3.1.6	INTEGER	read-create	Service category for this circuit: ubr Unspecified Bit Rate (best effort). ubrPcr Unspecified Bit Rate with Peak Cell Rate limit. nrtVbr Non-RealTime Variable Bit Rate. cbr Constant Bit Rate. rtVbr Realtime Variable Bit Rate.
I32 juniAtmSubIfVccPcr	1.3.6.1.4.1.4874.2.2.8.1.3.3.1.7	Integer32	read-create	Peak Cell Rate, in kilobits per second (kbps), of this circuit. This parameter is only required when juniAtmSubIfVccServiceCategory is configured to have one of the following values: ubrPcr nrtVbr cbr rtVbr
I32 juniAtmSubIfVccScr	1.3.6.1.4.1.4874.2.2.8.1.3.3.1.8	Integer32	read-create	Sustained Cell Rate, in kilobits per second (kbps), of this circuit. This parameter is only required when juniAtmSubIfVccServiceCategory is configured to have the following value: nrtVbr rtVbr
I32 juniAtmSubIfVccMbs	1.3.6.1.4.1.4874.2.2.8.1.3.3.1.9	Integer32	read-create	Maximum Burst Size, in cells, of this circuit. This parameter is only required when juniAtmSubIfVccServiceCategory is configured to have the following value: nrtVbr rtVbr
T/F juniAtmSubIfInverseArp	1.3.6.1.4.1.4874.2.2.8.1.3.3.1.10	TruthValue	read-create	Enables the inverse ARP protocol on this VCC; true(1) enables the protocol, false(2) disables it.
I32 juniAtmSubIfInverseArpRefresh	1.3.6.1.4.1.4874.2.2.8.1.3.3.1.11	Integer32	read-create	The refresh rate in minutes between inverse ARP protocol messages.
U32 juniAtmSubIfVccAssociatedVcClassId	1.3.6.1.4.1.4874.2.2.8.1.3.3.1.12	Unsigned32	read-create	The integer identifier of the ATM VC class associated with this ATM sub interface. A value for this identifier is determined by locating or creating an ATM VC class name in the juniAtmVcClassNameTable. A value of 0 means no VC class association exists for this VC.
juniAtmCircuitOamTable	1.3.6.1.4.1.4874.2.2.8.1.3.4		not-accessible	This table contains circuit OAM data for a PVC.
juniAtmCircuitOamEntry	1.3.6.1.4.1.4874.2.2.8.1.3.4.1		not-accessible	Each entry provides OAM data on an ATM PVC.
NUM juniAtmCircuitOamIfIndex	1.3.6.1.4.1.4874.2.2.8.1.3.4.1.1	InterfaceIndex	not-accessible	The ifIndex of the ATM subinterface.
OID juniAtmCircuitOamVpi	1.3.6.1.4.1.4874.2.2.8.1.3.4.1.2	AtmVpIdentifier	not-accessible	The VPI of the ATM VCC used by this ATM interface and PVC.
OID juniAtmCircuitOamVci	1.3.6.1.4.1.4874.2.2.8.1.3.4.1.3	AtmVcIdentifier	not-accessible	The VCI of the ATM VCC used by this ATM interface and PVC.
INT juniAtmCircuitOamAdminStatus	1.3.6.1.4.1.4874.2.2.8.1.3.4.1.4	INTEGER	read-write	The administrative state of OAM for the interface identified by this entry.
INT juniAtmCircuitOamLoopbackOperStatus	1.3.6.1.4.1.4874.2.2.8.1.3.4.1.5	INTEGER	read-only	The operational status of OAM for the interface identified by this entry. oamOperStatusNotSupported(0) - OAM not supported on this interface oamOperStatusDisabled(1) - VC integrity disabled oamOperStatusSent(2) - Loopback sent, awaiting response oamOperStatusReceived(3) - Loopback response received, awaiting frequency oamOperStatusFailed(4) - Loopback response not received, or invalid response received
INT juniAtmCircuitVcOamOperStatus	1.3.6.1.4.1.4874.2.2.8.1.3.4.1.6	INTEGER	read-only	The OAM VC operational status of this entry. oamVcOperStateAisState(0) - AIS cell received or underlying physical layer reporting transmission path AIS oamVcOperStateRdiState(1) - RDI cell received oamVcOperStateDownRetry(2) - OAM loopback failed, using retry frequency to verify that the VC is really down oamVcOperStateUpRetry(3) - OAM loopback successful, using retry frequency to verify that the VC is really up oamVcOperStateUp(4) - OAM loopback successful after up retry verification oamVcOperStateDown(5) - OAM loopback failed after down retry verification oamVcOperStateNotManaged(6)- No verification via loopback cells being performed oamVcOperStateVpAis(7) - F4 AIS cell received oamVcOperStateVpRdi(8) - F4 RDI cell received oamVcOperStateVcInVpRdi(9) - F4 RDI cell received; path failure oamVcOperStateVcInVpAis(10)- F4 AIS cell received; path failure oamVcOperStateSegAis(11) - Segment AIS cell received oamVcOperStateSegRdi(12) - Segment RDI cell received oamVcOperStateGenAis(13) - Connection failure; generating AIS cells.
I32 juniAtmCircuitOamLoopbackFrequency	1.3.6.1.4.1.4874.2.2.8.1.3.4.1.7	Integer32	read-write	The OAM loopback frequency in seconds.
C32 juniAtmCircuitInOamF5Cells	1.3.6.1.4.1.4874.2.2.8.1.3.4.1.8	Counter32	read-only	Received OAM F5 cells.
C32 juniAtmCircuitInOamCellsDropped	1.3.6.1.4.1.4874.2.2.8.1.3.4.1.9	Counter32	read-only	Received OAM cells that were dropped.
C32 juniAtmCircuitOutOamF5Cells	1.3.6.1.4.1.4874.2.2.8.1.3.4.1.10	Counter32	read-only	Transmitted OAM F5 cells.
C32 juniAtmCircuitInOamF5EndToEndLoopbackCells	1.3.6.1.4.1.4874.2.2.8.1.3.4.1.11	Counter32	read-only	Total received OAM F5 end-to-end loopback cells. Aggregate of juniAtmCircuitInOamF5EndToEndLoopbackCmds and juniAtmCircuitInOamF5EndToEndLoopbackRsps
C32 juniAtmCircuitInOamF5SegmentLoopbackCells	1.3.6.1.4.1.4874.2.2.8.1.3.4.1.12	Counter32	read-only	Total received OAM F5 segment loopback cells. Aggregate of juniAtmCircuitInOamF5SegmentLoopbackCmds and juniAtmCircuitInOamF5SegmentLoopbackRsps
C32 juniAtmCircuitInOamF5AisCells	1.3.6.1.4.1.4874.2.2.8.1.3.4.1.13	Counter32	read-only	Received OAM F5 AIS cells.
C32 juniAtmCircuitInOamF5RdiCells	1.3.6.1.4.1.4874.2.2.8.1.3.4.1.14	Counter32	read-only	Received OAM F5 RDI cells.
C32 juniAtmCircuitOutOamF5EndToEndLoopbackCells	1.3.6.1.4.1.4874.2.2.8.1.3.4.1.15	Counter32	read-only	Total transmitted OAM F5 end-to-end loopback cells. Aggregate of juniAtmCircuitOutOamF5EndToEndLoopbackCmds and juniAtmCircuitOutOamF5EndToEndLoopbackRsps
C32 juniAtmCircuitOutOamF5SegmentLoopbackCells	1.3.6.1.4.1.4874.2.2.8.1.3.4.1.16	Counter32	read-only	Total transmitted OAM F5 segment loopback cells. Aggregate of juniAtmCircuitOutOamF5SegmentLoopbackCmds and juniAtmCircuitOutOamF5SegmentLoopbackRsps
C32 juniAtmCircuitOutOamF5RdiCells	1.3.6.1.4.1.4874.2.2.8.1.3.4.1.17	Counter32	read-only	Transmitted OAM F5 RDI cells.
C32 juniAtmCircuitInOamF5EndToEndLoopbackCmds	1.3.6.1.4.1.4874.2.2.8.1.3.4.1.18	Counter32	read-only	Received OAM F5 end-to-end loopback commands.
C32 juniAtmCircuitInOamF5EndToEndLoopbackRsps	1.3.6.1.4.1.4874.2.2.8.1.3.4.1.19	Counter32	read-only	Received OAM F5 end-to-end loopback responses.
C32 juniAtmCircuitInOamF5SegmentLoopbackCmds	1.3.6.1.4.1.4874.2.2.8.1.3.4.1.20	Counter32	read-only	Received OAM F5 segment loopback commands.
C32 juniAtmCircuitInOamF5SegmentLoopbackRsps	1.3.6.1.4.1.4874.2.2.8.1.3.4.1.21	Counter32	read-only	Received OAM F5 segment loopback responses.
C32 juniAtmCircuitOutOamF5EndToEndLoopbackCmds	1.3.6.1.4.1.4874.2.2.8.1.3.4.1.22	Counter32	read-only	Transmitted OAM F5 end-to-end loopback commands.
C32 juniAtmCircuitOutOamF5EndToEndLoopbackRsps	1.3.6.1.4.1.4874.2.2.8.1.3.4.1.23	Counter32	read-only	Transmitted OAM F5 end-to-end loopback responses.
C32 juniAtmCircuitOutOamF5SegmentLoopbackCmds	1.3.6.1.4.1.4874.2.2.8.1.3.4.1.24	Counter32	read-only	Transmitted OAM F5 segment loopback commands.
C32 juniAtmCircuitOutOamF5SegmentLoopbackRsps	1.3.6.1.4.1.4874.2.2.8.1.3.4.1.25	Counter32	read-only	Transmitted OAM F5 segment loopback responses.
I32 juniAtmCircuitOamUpCount	1.3.6.1.4.1.4874.2.2.8.1.3.4.1.26	Integer32	read-write	Specifies the number of successive loopback cell responses to receive before a PVC is up for connectivity verification.
I32 juniAtmCircuitOamDownCount	1.3.6.1.4.1.4874.2.2.8.1.3.4.1.27	Integer32	read-write	Specifies the number of successive loopback cell responses not received before declaring a PVC down for connectivity verification.
I32 juniAtmCircuitOamRetryFrequency	1.3.6.1.4.1.4874.2.2.8.1.3.4.1.28	Integer32	read-write	Specifies the frequency (in seconds) to transmit loopback cells when verifying PVC state (up or down) for connectivity verification.
I32 juniAtmCircuitOamAlarmDownCount	1.3.6.1.4.1.4874.2.2.8.1.3.4.1.29	Integer32	read-write	Specifies the number of successive alarm (AIS or RDI) cells to receive before declaring a PVC down.
I32 juniAtmCircuitOamAlarmClearTimeout	1.3.6.1.4.1.4874.2.2.8.1.3.4.1.30	Integer32	read-write	Specifies how long to wait (in seconds) before declaring a PVC up after it has stopped receiving alarm cells.
juniAtmSubIfVccTrafficShapingTable	1.3.6.1.4.1.4874.2.2.8.1.3.5		not-accessible	This table contains entries for traffic shaping of ATM VCCs configured on ATM subinterfaces present in the system. This table augments the juniAtmSubIfVccTable only for VCCs that support traffic shapping. Attributes in this entry can only be configured at entry creation, and remain fixed for the lifetime of the entry.
juniAtmSubIfVccTrafficShapingEntry	1.3.6.1.4.1.4874.2.2.8.1.3.5.1		not-accessible	Each entry describes the traffic shping characteristics of an ATM subinterface VCC.
U32 juniAtmSubIfVccTrafficShapingCdvt	1.3.6.1.4.1.4874.2.2.8.1.3.5.1.1	Unsigned32	read-create	The network cell delay variation tolerance (CDVT) in tenths of a microsecond.
T/F juniAtmSubIfVccTrafficShapingClp0	1.3.6.1.4.1.4874.2.2.8.1.3.5.1.2	TruthValue	read-create	Specifies whether or not only CLP0 cells are to be policed according to the traffic contract. CLP1 cells are forwarded on a best-effort basis CLP-significant model for (VBR.2, VBR.3 conformance). Applicable only for VBR circuits.
T/F juniAtmSubIfVccTrafficShapingTagging	1.3.6.1.4.1.4874.2.2.8.1.3.5.1.3	TruthValue	read-create	Specifies whether or not CLP0 cells should be tagged for SCR policing (VBR.3 conformance). Applicable only for VBR circuits.
T/F juniAtmSubIfVccTrafficShapingPoliceObserve	1.3.6.1.4.1.4874.2.2.8.1.3.5.1.4	TruthValue	read-create	Specifies whether of not no policing action is to be taken (note the double negative; if true(1) then no policing action will be taken; if false(2) then policing action will be taken). Regardless of the state of this object, all counters will be incremented.
T/F juniAtmSubIfVccTrafficShapingPacketShaping	1.3.6.1.4.1.4874.2.2.8.1.3.5.1.5	TruthValue	read-create	Specifies whether of not to shape output traffic on a packet boundary.
juniAtmSubIfSvcConfigTable	1.3.6.1.4.1.4874.2.2.8.1.3.6		not-accessible	This table contains entries for extending the juniAtmSubIfTable to configure switched virtual connection (SVC) on the subinterfaces.
juniAtmSubIfSvcConfigEntry	1.3.6.1.4.1.4874.2.2.8.1.3.6.1		not-accessible	Each entry provides configuration parameters for an ATM SVC on the subinterface.
ROW juniAtmSubIfSvcRowStatus	1.3.6.1.4.1.4874.2.2.8.1.3.6.1.1	RowStatus	read-create	Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy
ATM juniAtmSubIfSvcConfigDestAtmAddress	1.3.6.1.4.1.4874.2.2.8.1.3.6.1.2	AtmAddr	read-create	Specifies the destination ATM NSAP address of the circuit.
INT juniAtmSubIfSvcConfigCircuitType	1.3.6.1.4.1.4874.2.2.8.1.3.6.1.3	INTEGER	read-create	Specifies the encapsulation used by the circuit to carry IP datagrams. Encapsulations are as specified in RFC1483 Multiprotocol Interconnect over ATM.
INT juniAtmSubIfSvcConfigServiceCategory	1.3.6.1.4.1.4874.2.2.8.1.3.6.1.4	INTEGER	read-create	Service category for this circuit: ubr Unspecified Bit Rate (best effort). ubrPcr Unspecified Bit Rate with Peak Cell Rate limit. nrtVbr Non-RealTime Variable Bit Rate. cbr Constant Bit Rate. rtVbr Realtime Variable Bit Rate.
U32 juniAtmSubIfSvcConfigPcr	1.3.6.1.4.1.4874.2.2.8.1.3.6.1.5	Unsigned32	read-create	Peak Cell Rate, in kilo-bits per second (kbps), of this circuit.
U32 juniAtmSubIfSvcConfigScr	1.3.6.1.4.1.4874.2.2.8.1.3.6.1.6	Unsigned32	read-create	Sustained Cell Rate, in kilo-bits per second (kbps), of this circuit.
U32 juniAtmSubIfSvcConfigMbs	1.3.6.1.4.1.4874.2.2.8.1.3.6.1.7	Unsigned32	read-create	Maximum Burst Size, in cells, of this circuit.
U32 juniAtmSubIfSvcConfigCdvt	1.3.6.1.4.1.4874.2.2.8.1.3.6.1.8	Unsigned32	read-create	Specify the network Cell Delay Variation Tolerance.
T/F juniAtmSubIfSvcConfigClp0	1.3.6.1.4.1.4874.2.2.8.1.3.6.1.9	TruthValue	read-create	Specify that only CLP0 cells are to be policed according to the traffic contract. CLP1 cells are forwarded on a best-effort basis CLP-significant model for (VBR.2, VBR.3 conformance).
T/F juniAtmSubIfSvcConfigTagging	1.3.6.1.4.1.4874.2.2.8.1.3.6.1.10	TruthValue	read-create	Specify that CLP0 cells should be tagged for SCR policing (VBR.3 conformance).
T/F juniAtmSubIfSvcConfigObserve	1.3.6.1.4.1.4874.2.2.8.1.3.6.1.11	TruthValue	read-create	Specify that no policing action is to be taken; only counters are incremented.
T/F juniAtmSubIfSvcConfigPacketDiscard	1.3.6.1.4.1.4874.2.2.8.1.3.6.1.12	TruthValue	read-create	Enable early packet Discard for this circuit.
ATM juniAtmSubIfSvcConfigDestE164Address	1.3.6.1.4.1.4874.2.2.8.1.3.6.1.13	AtmAddr	read-create	Specifies the destination ATM E164 address of the circuit.
T/F juniAtmSubIfDescriptionExport	1.3.6.1.4.1.4874.2.2.8.1.3.7	TruthValue	read-write	Enabling of this object will program the subinterface description down to the applicable line card. Note, the subinterface description sent down to the line card is a truncated version (32 bytes) of the ifAlias.
juniAtmNbma	1.3.6.1.4.1.4874.2.2.8.1.4
juniAtmNbmaMapTable	1.3.6.1.4.1.4874.2.2.8.1.4.1		not-accessible	This table contains entries for ATM NBMA maps.
juniAtmNbmaMapEntry	1.3.6.1.4.1.4874.2.2.8.1.4.1.1		not-accessible	Each entry describes the characteristics of an ATM NBMA map.
JUN juniAtmNbmaMapName	1.3.6.1.4.1.4874.2.2.8.1.4.1.1.1	JuniAtmNbmaMapName	not-accessible	The NBMA map name.
I32 juniAtmNbmaMapVcd	1.3.6.1.4.1.4874.2.2.8.1.4.1.1.2	Integer32	not-accessible	An integer identifier for the ATM circuit, used in conjunction with the command-line interface. The value must be unique among VCs configured on the same ATM interface.
IP juniAtmNbmaMapIpAddress	1.3.6.1.4.1.4874.2.2.8.1.4.1.1.3	IpAddress	read-create	The IP address associated with this entry.
OID juniAtmNbmaMapVpi	1.3.6.1.4.1.4874.2.2.8.1.4.1.1.4	AtmVpIdentifier	read-only	The VPI identifier of the ATM circuit.
OID juniAtmNbmaMapVci	1.3.6.1.4.1.4874.2.2.8.1.4.1.1.5	AtmVcIdentifier	read-only	The VCI identifier of the ATM circuit.
NUM juniAtmNbmaMapIfIndex	1.3.6.1.4.1.4874.2.2.8.1.4.1.1.6	InterfaceIndexOrZero	read-only	The ifIndex of the ATM major interface associated with this entry. The value of this object will be zero when the map is not applied to an interface.
T/F juniAtmNbmaMapBroadcast	1.3.6.1.4.1.4874.2.2.8.1.4.1.1.7	TruthValue	read-create	The broadcast enable/disable setting for this entry. The value true(1) enable broadcast support; disable(2) disabled broadcast support for this entry.
ROW juniAtmNbmaMapRowStatus	1.3.6.1.4.1.4874.2.2.8.1.4.1.1.8	RowStatus	read-create	Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy Additional notes to aid the network manager: - NBMA maps are not supported on dynamic interface. - NBMA maps can only be applied to a single major ATM interface at a time. - NBMA maps cannot be deleted unless the map is removed from the ATM interface (juniAtmNbmaMapIfIndex = 0). - The values of juniAtmNbmaMapVpi, juniAtmNbmaMapVci and juniAtmNbmaMapIfIndex are zero until the map is applied to a major ATM interface. - To create an entry in this table, the following objects must be present in the set PDU: juniAtmNbmaMapIpAddress juniAtmNbmaMapBroadcast juniAtmNbmaMapRowStatus - Once created, only the following objects can be modified: juniAtmNbmaMapBroadcast
juniAtmNbmaMapListTable	1.3.6.1.4.1.4874.2.2.8.1.4.2		not-accessible	This table contains entries for ATM NBMA map lists.
juniAtmNbmaMapListEntry	1.3.6.1.4.1.4874.2.2.8.1.4.2.1		not-accessible	Each entry describes the characteristics of an ATM NBMA map.
JUN juniAtmNbmaMapListName	1.3.6.1.4.1.4874.2.2.8.1.4.2.1.1	JuniAtmNbmaMapName	not-accessible	The NBMA Map List name.
ROW juniAtmNbmaMapListRowStatus	1.3.6.1.4.1.4874.2.2.8.1.4.2.1.2	RowStatus	read-create	Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy
juniAtmPing	1.3.6.1.4.1.4874.2.2.8.1.5
juniAtmPingTestTypes	1.3.6.1.4.1.4874.2.2.8.1.5.1
juniAtmPingTestOamSeg	1.3.6.1.4.1.4874.2.2.8.1.5.1.1			This identifies an OAM Ping (multiple loopbacks) Test on a VPL, VPC, VCL, or VCC termination point, using segment OAM cells. The test type must have appended to it a code that uniquely identifies an intermediate point responsible for looping back each cell. If this is absent, the loopbacks are performed at the end of the segment or connection. E.g., the OID { juniAtmPingTestOamSeg 5 } identifies that the loopbacks should be performed at the intermediate point labeled 5.
juniAtmPingTestOamE2E	1.3.6.1.4.1.4874.2.2.8.1.5.1.2			This identifies an OAM Ping (multiple loopbacks) Test on a VPL, VPC, VCL, or VCC termination point, using end-to-end OAM cells.
juniAtmVpPingTable	1.3.6.1.4.1.4874.2.2.8.1.5.2		not-accessible	This table contains entries for extending the ATM-FORUM-SNMP-M4-MIB atmM4VpTestTable to do ping (multiple loopback) type testing.
juniAtmVpPingEntry	1.3.6.1.4.1.4874.2.2.8.1.5.2.1		not-accessible	Each entry describes the characteristics, status and results of the most recent ATM ping test.
U32 juniAtmVpPingProbeCount	1.3.6.1.4.1.4874.2.2.8.1.5.2.1.1	Unsigned32	read-write	The number of ping probes (OAM cells) to be sent to complete the test.
U32 juniAtmVpPingTimeOut	1.3.6.1.4.1.4874.2.2.8.1.5.2.1.2	Unsigned32	read-write	Specifies the time-out value, in seconds, for a remote ping operation.
BIT juniAtmVpPingCtlTrapGeneration	1.3.6.1.4.1.4874.2.2.8.1.5.2.1.3	Bits	read-write	The value of this object determines when and if to generate a notification for this entry: testCompletion(0) - Generate a juniPingTestCompleted notification. The value of this object defaults to zero, indicating that no notification has been selected.
U32 juniAtmVpPingSentProbes	1.3.6.1.4.1.4874.2.2.8.1.5.2.1.4	Unsigned32	read-only	The number of ping probes (OAM cells) that have been sent thus far for this test. The value of this object MUST be set to zero when the atmfM4VpTestStatus object transitions from notInUse(0) to inUse(1).
U32 juniAtmVpPingProbeResponses	1.3.6.1.4.1.4874.2.2.8.1.5.2.1.5	Unsigned32	read-only	The number of ping responses that have been received thus far for this test. The value of this object MUST be set to zero when the atmfM4VpTestStatus object transitions from notInUse(0) to inUse(1).
TIM juniAtmVpPingStartTime	1.3.6.1.4.1.4874.2.2.8.1.5.2.1.6	TimeStamp	read-only	The time (sysUpTime) when the test started.
U32 juniAtmVpPingMinRtt	1.3.6.1.4.1.4874.2.2.8.1.5.2.1.7	Unsigned32	read-only	The shortest round-trip-time (RTT) for the pings that have received responses. The value of this object MUST be set to zero when the atmfM4VpTestStatus object transitions from notInUse(0) to inUse(1). A value of zero for this object implies that no ping responses have been received for the current test.
U32 juniAtmVpPingMaxRtt	1.3.6.1.4.1.4874.2.2.8.1.5.2.1.8	Unsigned32	read-only	The longest round-trip-time (RTT) for the pings that have received responses. The value of this object MUST be set to zero when the atmfM4VpTestStatus object transitions from notInUse(0) to inUse(1). A value of zero for this object implies that no ping responses have been received for the current test.
U32 juniAtmVpPingAverageRtt	1.3.6.1.4.1.4874.2.2.8.1.5.2.1.9	Unsigned32	read-only	The average round-trip-time (RTT) for all the pings that have received responses. The value of this object MUST be set to zero when the atmfM4VpTestStatus object transitions from notInUse(0) to inUse(1). A value of zero for this object implies that no ping responses have been received for the current test.
juniAtmVcPingTable	1.3.6.1.4.1.4874.2.2.8.1.5.3		not-accessible	This table contains entries for extending the ATM-FORUM-SNMP-M4-MIB atmM4VcTestTable to do ping (multiple loopback) type testing.
juniAtmVcPingEntry	1.3.6.1.4.1.4874.2.2.8.1.5.3.1		not-accessible	Each entry describes the characteristics, status and results of the most recent ATM ping test.
U32 juniAtmVcPingProbeCount	1.3.6.1.4.1.4874.2.2.8.1.5.3.1.1	Unsigned32	read-write	The number of ping probes (OAM cells) to be sent to complete the test.
U32 juniAtmVcPingTimeOut	1.3.6.1.4.1.4874.2.2.8.1.5.3.1.2	Unsigned32	read-write	Specifies the time-out value, in seconds, for a remote ping operation.
BIT juniAtmVcPingCtlTrapGeneration	1.3.6.1.4.1.4874.2.2.8.1.5.3.1.3	Bits	read-write	The value of this object determines when and if to generate a notification for this entry: testCompletion(0) - Generate a juniPingTestCompleted notification. The value of this object defaults to zero, indicating that no notification has been selected.
U32 juniAtmVcPingSentProbes	1.3.6.1.4.1.4874.2.2.8.1.5.3.1.4	Unsigned32	read-only	The number of ping probes (OAM cells) that have been sent thus far for this test. The value of this object MUST be set to zero when the atmfM4VcTestStatus object transitions from notInUse(0) to inUse(1).
U32 juniAtmVcPingProbeResponses	1.3.6.1.4.1.4874.2.2.8.1.5.3.1.5	Unsigned32	read-only	The number of ping responses that have been received thus far for this test. The value of this object MUST be set to zero when the atmfM4VcTestStatus object transitions from notInUse(0) to inUse(1).
TIM juniAtmVcPingStartTime	1.3.6.1.4.1.4874.2.2.8.1.5.3.1.6	TimeStamp	read-only	The time (sysUpTime) when the test started.
U32 juniAtmVcPingMinRtt	1.3.6.1.4.1.4874.2.2.8.1.5.3.1.7	Unsigned32	read-only	The shortest round-trip-time (RTT) for the pings that have received responses. The value of this object MUST be set to zero when the atmfM4VcTestStatus object transitions from notInUse(0) to inUse(1). A value of zero for this object implies that no ping responses have been received for the current test.
U32 juniAtmVcPingMaxRtt	1.3.6.1.4.1.4874.2.2.8.1.5.3.1.8	Unsigned32	read-only	The longest round-trip-time (RTT) for the pings that have received responses. The value of this object MUST be set to zero when the atmfM4VcTestStatus object transitions from notInUse(0) to inUse(1). A value of zero for this object implies that no ping responses have been received for the current test.
U32 juniAtmVcPingAverageRtt	1.3.6.1.4.1.4874.2.2.8.1.5.3.1.9	Unsigned32	read-only	The average round-trip-time (RTT) for all the pings that have received responses. The value of this object MUST be set to zero when the atmfM4VcTestStatus object transitions from notInUse(0) to inUse(1). A value of zero for this object implies that no ping responses have been received for the current test.
juniAtmPingTestCode	1.3.6.1.4.1.4874.2.2.8.1.5.4
juniAtmPingTestCodeOamDisabled	1.3.6.1.4.1.4874.2.2.8.1.5.4.1			This test code indicates that the ATM ping operation cannot be initiated or is aborted because the juniAtmIfOamCellRxAdminState is set to disabled.
juniAtmPingTestCodeCircuitDown	1.3.6.1.4.1.4874.2.2.8.1.5.4.2			This test code indicates that the ATM ping operation cannot be initiated or is aborted because the operational status of the ATM circuit is down.
juniAtmPingTestCodeStopped	1.3.6.1.4.1.4874.2.2.8.1.5.4.3			This test code indicates that the ATM ping operation is administratively stopped by an External Management.
juniAtmPingTestCodeOamVcOperState	1.3.6.1.4.1.4874.2.2.8.1.5.4.4			This test code indicates that the ATM ping operation cannot be initiated or is aborted because the circuit is down because of a OAM fault condition. This is possible if juniAtmCircuitVcOamOperStatus is one of the following: oamVcOperStateAisState(0) - AIS cell received or underlying physical layer reporting transmission path AIS. oamVcOperStateRdiState(1) - RDI cell received.
juniAtmPingTestCodeMaxPingCountReached	1.3.6.1.4.1.4874.2.2.8.1.5.4.5			This test code indicates that the ping operation cannot be initiated as the maximum number of ping possible on this interfaces exceeds the allowable limit.
juniAtmPingTestCodeInvalidParams	1.3.6.1.4.1.4874.2.2.8.1.5.4.6			This Test Code identities the Ping operation cannot be initiated as one or more of the Ping Parameters is Invalid.
juniAtmLocation	1.3.6.1.4.1.4874.2.2.8.1.6
NUM juniAtmSubIfLocationType	1.3.6.1.4.1.4874.2.2.8.1.6.1	JuniInterfaceLocationType	read-only	Describes the interpretation of JuniInterfaceLocationValue object values into platform-dependent interface location components, e.g., 'slot.port' on an ERX.
juniAtmSubIfLocationTable	1.3.6.1.4.1.4874.2.2.8.1.6.2		not-accessible	The entries in this table report the ifIndex of ATM Subinterfaces by location.
juniAtmSubIfLocationEntry	1.3.6.1.4.1.4874.2.2.8.1.6.2.1		not-accessible	A specification of ATM subinterfaces by location.
NUM juniAtmSubIfLocationIndex	1.3.6.1.4.1.4874.2.2.8.1.6.2.1.1	JuniInterfaceLocationValue	not-accessible	The value of a platform interface location.
NUM juniAtmSubIfLocationIfIndex	1.3.6.1.4.1.4874.2.2.8.1.6.2.1.2	InterfaceIndex	read-only	The ifIndex value of this subinterface.
juniAtmVcClass	1.3.6.1.4.1.4874.2.2.8.1.7
juniAtmVcClassNameTable	1.3.6.1.4.1.4874.2.2.8.1.7.1		not-accessible	The entries in this table provide mappings of ATM VC class names to local integer identifiers. These integers are used as indexes into other MIB tables containing ATM VC attributes associated with the same VC class name.
juniAtmVcClassNameEntry	1.3.6.1.4.1.4874.2.2.8.1.7.1.1		not-accessible	A mapping of ATM VC class name to an integer identifier for the ATM VC class.
STR juniAtmVcClassName	1.3.6.1.4.1.4874.2.2.8.1.7.1.1.1	DisplayString	read-only	The ATM VC class name uniquely identifying this entry.
ROW juniAtmVcClassNameRowStatus	1.3.6.1.4.1.4874.2.2.8.1.7.1.1.2	RowStatus	read-create	Controls creation/deletion of entries in this table. Only the values 'createAndGo' ,'destroy', 'active' and 'notInService' may be SET. The SNMP manager would set the row status to notInService before making any VC class attribute changes explained in juniAtmVcClassTable. Once the VC class attribute changes are complete, the SNMP manager would set the row status to active, upon which the VC class attribute changes would be committed. Any ATM VC class attribute changes that are made when the row status is 'active' are committed right away.
U32 juniAtmVcClassNameId	1.3.6.1.4.1.4874.2.2.8.1.7.1.1.3	Unsigned32	read-only	The integer identifier associated with this VC class name. The value of this identifier is assigned by the device when an entry in this table is created.
juniAtmVcClassIdTable	1.3.6.1.4.1.4874.2.2.8.1.7.2		not-accessible	Provides inverse mapping of ATM VC class IDs to ATM VC class names.
juniAtmVcClassIdEntry	1.3.6.1.4.1.4874.2.2.8.1.7.2.1		not-accessible	A mapping of an integer identifier to an ATM VC class name.
U32 juniAtmVcClassIdId	1.3.6.1.4.1.4874.2.2.8.1.7.2.1.1	Unsigned32	not-accessible	The integer identifier associated with this ATM VC class name.
STR juniAtmVcClassIdName	1.3.6.1.4.1.4874.2.2.8.1.7.2.1.2	DisplayString	read-only	The ATM VC class name having the associated identifier.
juniAtmVcClassTable	1.3.6.1.4.1.4874.2.2.8.1.7.3		not-accessible	This table contains Juniper ATM VC Class entries which can be used to specify the ATM PVC attributes either at creation or modification time. A row in this table with default values is created when an entry in juniAtmVcClassNameTable is created.
juniAtmVcClassEntry	1.3.6.1.4.1.4874.2.2.8.1.7.3.1		not-accessible	Each entry contains the attributes of the ATM VC which would be applied to the VC either at creation or modification time when this ATM VC class is associated to it.
U32 juniAtmVcClassId	1.3.6.1.4.1.4874.2.2.8.1.7.3.1.1	Unsigned32	not-accessible	The integer identifier associated with this ATM VC class. A value for this identifier is determined by locating or creating an ATM VC class name in the juniAtmVcClassNameTable.
INT juniAtmVcClassVccType	1.3.6.1.4.1.4874.2.2.8.1.7.3.1.2	INTEGER	read-write	Specifies the encapsulation used by the circuit to carry IP datagrams. Encapsulations are as specified in RFC1483 Multiprotocol Interconnect over ATM. The 'autoconfig' value will recognize both VC Mux and LLC formats. The 'aal5' and 'aal0' values are used for encapsulation methods for transport of ATM frames and cells over IP and MPLS networks when no encapsulation method is specified.
INT juniAtmVcClassVccServiceCategory	1.3.6.1.4.1.4874.2.2.8.1.7.3.1.3	INTEGER	read-write	Service category for this circuit: ubr Unspecified Bit Rate (best effort). ubrPcr Unspecified Bit Rate with Peak Cell Rate limit. nrtVbr Non-RealTime Variable Bit Rate. cbr Constant Bit Rate. rtVbr Realtime Variable Bit Rate.
I32 juniAtmVcClassVccPcr	1.3.6.1.4.1.4874.2.2.8.1.7.3.1.4	Integer32	read-write	Peak Cell Rate, in kilobits per second (kbps), of this circuit. This parameter is only required when juniAtmVcClassVccServiceCategory is configured to have one of the following values: ubrPcr nrtVbr cbr rtVbr
I32 juniAtmVcClassVccScr	1.3.6.1.4.1.4874.2.2.8.1.7.3.1.5	Integer32	read-write	Sustained Cell Rate, in kilobits per second (kbps), of this circuit. This parameter is only required when juniAtmVcClassVccServiceCategory is configured to have the following value: nrtVbr rtVbr
I32 juniAtmVcClassVccMbs	1.3.6.1.4.1.4874.2.2.8.1.7.3.1.6	Integer32	read-write	Maximum Burst Size, in cells, of this circuit. This parameter is only required when juniAtmVcClassVccServiceCategory is configured to have the following value: nrtVbr rtVbr
INT juniAtmVcClassVccOamAdminStatus	1.3.6.1.4.1.4874.2.2.8.1.7.3.1.7	INTEGER	read-write	The OAM VC integrity administrative state of the ATM VC associated with this class.
I32 juniAtmVcClassVccOamLoopbackFrequency	1.3.6.1.4.1.4874.2.2.8.1.7.3.1.8	Integer32	read-write	The OAM loopback frequency in seconds.
I32 juniAtmVcClassVccOamUpCount	1.3.6.1.4.1.4874.2.2.8.1.7.3.1.9	Integer32	read-write	Specifies the number of successive loopback cell responses to receive before the ATM VC associated with this class is declared up for connectivity verification.
I32 juniAtmVcClassVccOamDownCount	1.3.6.1.4.1.4874.2.2.8.1.7.3.1.10	Integer32	read-write	Specifies the number of successive loopback cell responses not received before declaring the ATM VC associated with this class as down for connectivity verification.
I32 juniAtmVcClassVccOamRetryFrequency	1.3.6.1.4.1.4874.2.2.8.1.7.3.1.11	Integer32	read-write	Specifies the frequency (in seconds) to transmit loopback cells when verifying the ATM VC operational state associated with this class (up or down) for connectivity verification.
I32 juniAtmVcClassVccOamAlarmDownCount	1.3.6.1.4.1.4874.2.2.8.1.7.3.1.12	Integer32	read-write	Specifies the number of successive alarm (AIS or RDI) cells to receive before declaring the ATM VC associated with class as down.
I32 juniAtmVcClassVccOamAlarmClearTimeout	1.3.6.1.4.1.4874.2.2.8.1.7.3.1.13	Integer32	read-write	Specifies how long to wait (in seconds) before declaring the ATM VC associated with class as up after it has stopped receiving alarm cells.
T/F juniAtmVcClassVccInverseArp	1.3.6.1.4.1.4874.2.2.8.1.7.3.1.14	TruthValue	read-write	Enables the inverse ARP protocol on the ATM VC associated with this class; true(1) enables the protocol, false(2) disables it.
I32 juniAtmVcClassVccInverseArpRefresh	1.3.6.1.4.1.4874.2.2.8.1.7.3.1.15	Integer32	read-write	The refresh rate in minutes between inverse ARP protocol messages.
juniAtmTraps	1.3.6.1.4.1.4874.2.2.8.3
juniAtmTrapPrefix	1.3.6.1.4.1.4874.2.2.8.3.0
NTF juniAtmVpPingTestCompleted	1.3.6.1.4.1.4874.2.2.8.3.0.1			Generated at the completion of a AtmfM4VpTest when the corresponding juniAtmVpPingCtlTrapGeneration object has the testCompletion(0) bit set.
NTF juniAtmVcPingTestCompleted	1.3.6.1.4.1.4874.2.2.8.3.0.2			Generated at the completion of a AtmfM4VcTest when the corresponding juniAtmVcPingCtlTrapGeneration object has the testCompletion(0) bit set.
juniAtmConformance	1.3.6.1.4.1.4874.2.2.8.4
juniAtmCompliances	1.3.6.1.4.1.4874.2.2.8.4.1
juniAtmCompliance	1.3.6.1.4.1.4874.2.2.8.4.1.1			Obsolete compliance statement for entities which implement the Juniper ATM MIB. This statement became obsolete when support was added for NBMA map lists and ATM ping.
juniAtmCompliance2	1.3.6.1.4.1.4874.2.2.8.4.1.2			Obsolete compliance statement for entities which implement the Juniper ATM MIB. This statement became obsolete when support was added for traffic shapping on VCC subinterfaces.
juniAtmCompliance3	1.3.6.1.4.1.4874.2.2.8.4.1.3			Obsolete compliance statement for entities which implement the Juniper ATM MIB. This statement became obsolete when support was added for connection admission control (CAC).
juniAtmCompliance4	1.3.6.1.4.1.4874.2.2.8.4.1.4			Obsolete compliance statement for entities which implement the Juniper ATM MIB. This statement became obsolete when ATM SVC, CAC used bandwidth and sub-interface address objects were added.
juniAtmCompliance5	1.3.6.1.4.1.4874.2.2.8.4.1.5			Obsolete compliance statement for entities which implement the Juniper ATM MIB. This statement became obsolete when CAC recieve bandwith and E164 public addressing support was added.
juniAtmCompliance6	1.3.6.1.4.1.4874.2.2.8.4.1.6			Obsolete compliance statement for entities which implement the Juniper ATM MIB. This statement became obsolete when F4 flow OAM circuit config and stats tables were added to the Juniper ATM MIB.
juniAtmCompliance7	1.3.6.1.4.1.4874.2.2.8.4.1.7			Obsolete compliance statement for entities which implement the Juniper ATM MIB. This statement became obsolete when the juniAtmLocationGroup was added.
juniAtmCompliance8	1.3.6.1.4.1.4874.2.2.8.4.1.8			Obsolete compliance statement for entities which implement the Juniper ATM MIB. This statement became obsolete when support was added to export the subinterface description to the line cards.
juniAtmCompliance9	1.3.6.1.4.1.4874.2.2.8.4.1.9			Obsolete compliance statement for entities which implement the Juniper ATM MIB. This statement was obsoleted when the juniAtmMartiniGroup was added.
juniAtmCompliance10	1.3.6.1.4.1.4874.2.2.8.4.1.10			Obsolete compliance statement for entities which implement the Juniper ATM MIB. This statement became obsolete when juniAtmIfCacAvailableBandwidthRx, juniAtmIfE164Autoconversion, juniAtmIfE164Gateway, and juniAtmIfE164OneToOneAddrTrans were deprecated.
juniAtmCompliance11	1.3.6.1.4.1.4874.2.2.8.4.1.11			Obsolete compliance statement for entities which implement the Juniper ATM MIB. This statement became obsolete when juniAtmGroup8 was added.
juniAtmCompliance12	1.3.6.1.4.1.4874.2.2.8.4.1.12			The compliance statement for entities which implement the Juniper ATM MIB. This statement became obsolete when juniAtmVpStatsGroup was added.
juniAtmCompliance13	1.3.6.1.4.1.4874.2.2.8.4.1.13			The compliance statement for entities which implement the Juniper ATM MIB. This statement became obsolete when SVC support was removed.
juniAtmCompliance14	1.3.6.1.4.1.4874.2.2.8.4.1.14			The compliance statement for entities which implement the Juniper ATM MIB.
juniAtmGroups	1.3.6.1.4.1.4874.2.2.8.4.2
juniAtmGroup	1.3.6.1.4.1.4874.2.2.8.4.2.1			Obsolete collection of objects providing management of ATM interfaces in a Juniper product. This group became obsolete when the juniAtmIfMapGroup object was added.
juniAtmAal5Group	1.3.6.1.4.1.4874.2.2.8.4.2.2			A collection of objects providing management of AAL5 interfaces in a Juniper product.
juniAtmSubIfGroup	1.3.6.1.4.1.4874.2.2.8.4.2.3			Obsolete collection of objects providing management of ATM subinterfaces in a Juniper product. This group became obsolete when juniAtmSubIfNbma, juniAtmSubIfInverseArp, and juniAtmSubIfInverseArpRefresh were added.
juniAtmVpTunnelGroup	1.3.6.1.4.1.4874.2.2.8.4.2.4			A collection of objects providing management of VP tunnels in a Juniper product.
juniAtmNbmaMapGroup	1.3.6.1.4.1.4874.2.2.8.4.2.5			A collection of object providing management of NBMA in a Juniper product.
juniAtmSubIfGroup2	1.3.6.1.4.1.4874.2.2.8.4.2.6			Obsolete collection of objects providing management of ATM subinterfaces in a Juniper product. This group became obsolete when juniAtmSubIfAddress was added.
juniAtmVpPingControlGroup	1.3.6.1.4.1.4874.2.2.8.4.2.7			A collection of object providing management of ATM VPL Ping testing in a Juniper product.
juniAtmVcPingControlGroup	1.3.6.1.4.1.4874.2.2.8.4.2.8			A collection of object providing management of ATM VCL Ping testing in a Juniper product.
juniAtmPingTrapGroup	1.3.6.1.4.1.4874.2.2.8.4.2.9			A collection of notifications supporting ATM Ping testing in a Juniper product.
juniAtmGroup2	1.3.6.1.4.1.4874.2.2.8.4.2.10			Obsolete collection of objects providing management of ATM interfaces in a Juniper product. This group became obsolete when support was added for connection admission control (CAC).
juniAtmTrafficShapingGroup	1.3.6.1.4.1.4874.2.2.8.4.2.11			A collection of objects providing management of ATM traffic shaping in a Juniper product.
juniAtmGroup3	1.3.6.1.4.1.4874.2.2.8.4.2.12			Obsolete collection of objects providing management of ATM interfaces in a Juniper product. This group became obsolete when support was added for connection admission control (CAC) used bandwidth.
juniAtmGroup4	1.3.6.1.4.1.4874.2.2.8.4.2.13			Obsolete collection of objects providing management of ATM interfaces in a Juniper product. This group became obsolete when CAC recieve bandwith and E164 public addressing objects were added.
juniAtmSvcGroup	1.3.6.1.4.1.4874.2.2.8.4.2.14			Obsolete collection of objects providing management of ATM SVC interfaces in a Juniper product. This group became obsolete when E164 public addressing support was added.
juniAtmSubIfGroup3	1.3.6.1.4.1.4874.2.2.8.4.2.15			Obsolete collection of objects providing management of ATM subinterfaces in a Juniper product. This group became obsolete when juniAtmSubIfMtu was added.
juniAtmGroup5	1.3.6.1.4.1.4874.2.2.8.4.2.16			Obsolete collection of objects providing management of ATM interfaces in a Juniper product. This group became obsolete when ATM VP description support was added.
juniAtmSvcGroup2	1.3.6.1.4.1.4874.2.2.8.4.2.17			A collection of objects providing management of ATM SVC interfaces in a Juniper product.
juniAtmPnniGroup	1.3.6.1.4.1.4874.2.2.8.4.2.18			A collection of objects providing management of PNNI Routing Control Channels in a Juniper product.
juniAtmSubIfGroup4	1.3.6.1.4.1.4874.2.2.8.4.2.19			Obsolete collection of objects providing management of ATM subinterfaces in a Juniper product. This group became obsolete when support was added to export the subinterface description to the line cards.
juniAtmF4OamCircuitGroup	1.3.6.1.4.1.4874.2.2.8.4.2.20			Obsolete collection of objects providing management of ATM F4 flow OAM circuits in a Juniper product.
juniAtmGroup6	1.3.6.1.4.1.4874.2.2.8.4.2.21			Obsolete collection of objects providing management of ATM interfaces in a Juniper product. This group became obsolete when bulk-configuration profile override support was added.
juniAtmLocationGroup	1.3.6.1.4.1.4874.2.2.8.4.2.22			A collection of objects providing interface location information in a Juniper product.
juniAtmSubIfGroup5	1.3.6.1.4.1.4874.2.2.8.4.2.23			Obsolete collection of objects providing management of ATM subinterfaces in a Juniper product.
juniAtmMartiniGroup	1.3.6.1.4.1.4874.2.2.8.4.2.24			A collection of objects providing ATM Martini cell aggregation configuration.
juniAtmGroup7	1.3.6.1.4.1.4874.2.2.8.4.2.25			Obsolete collection of objects providing management of ATM interfaces in a Juniper product.
juniAtmGroup8	1.3.6.1.4.1.4874.2.2.8.4.2.26			A collection of objects providing management of ATM interfaces in a Juniper product.
juniAtmVpStatsGroup	1.3.6.1.4.1.4874.2.2.8.4.2.27			A collection of objects providing ATM VP level statistics.
juniAtmSubIfGroup6	1.3.6.1.4.1.4874.2.2.8.4.2.28			Obsolete collection of objects providing management of ATM subinterfaces in a Juniper product. This group became obsolete when ATM SVC support was removed.
juniAtmF4OamCircuitGroup2	1.3.6.1.4.1.4874.2.2.8.4.2.29			A collection of objects providing management of ATM F4 flow OAM circuits in a Juniper product.
juniAtmGroup9	1.3.6.1.4.1.4874.2.2.8.4.2.30			A collection of objects providing management of ATM interfaces in a Juniper product.
juniAtmSubIfGroup7	1.3.6.1.4.1.4874.2.2.8.4.2.31			A collection of objects providing management of ATM subinterfaces in a Juniper product.
juniAtmVcClassGroup	1.3.6.1.4.1.4874.2.2.8.4.2.32			A collection of objects providing management of ATM VC class in a Juniper product.

RFC description

ATM interface, tunnel, and OAM management for Juniper networks including virtual path and circuit operations.

Start monitoring Juniper E-series router, ATM/DSL broadband access platform (ATM UNI interfaces) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Juniper-UNI-ATM-MIB