All MIBs › HUAWEI-VOP-MIB
Organization: Huawei Technologies co.,Ltd.
Last Updated: 2011-12-02
Category: Domain: Telephony/VoIP, Domain: VoIP/Telephony, Vendor: Huawei
Description: Huawei VoP (Voice over Packet) MIB for managing voice-over-packet parameters including packetization intervals and codec selection.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is HUAWEI-VOP-MIB?
HUAWEI-VOP-MIB is a Huawei enterprise MIB implementing the Broadband Forum TR-165 Vector-of-Profiles data model for Voice-over-Packet configuration on xDSL/broadband access equipment. It exposes configuration objects for voice service parameters such as packetization interval and codec selection used to provision VoIP behavior across broadband subscriber lines. Its monitoring role is primarily configuration-status oriented, letting an administrator confirm which voice profile, codec, and packet-timing settings are actually applied to a line rather than tracking hardware faults directly. It explicitly depends on the Broadband Forum TR-165 Vector-of-Profiles framework referenced in its module description, tying it to a recognized industry standard beyond Huawei's own conventions. It is deployed on Huawei broadband access/gateway equipment delivering voice services over DSL or packet access lines, where HUAWEI-VOP-MIB SNMP monitoring confirms the correct codec and profile settings are applied per subscriber line.
IPNetwork Monitor allows you to monitor SNMP objects defined in HUAWEI-VOP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Huawei broadband access gateway
- Huawei xDSL voice-enabled CPE/access equipment
Monitoring Examples
A plausible VoP structure would be a profile table keyed by profile ID or line index containing codec selection and packetization-interval fields, following a VoP profile Table/Entry pattern. An administrator would poll the applied codec and packet interval per line to verify voice QoS settings match provisioning intent, and a mismatch would explain unexpected voice-quality complaints on a given subscriber line.
What Can Be Monitored
- voice profile assignment
- codec selection
- packetization interval
- VoP configuration status
This MIB depends on
Related MIBs
Imported Objects
From HUAWEI-DEVICE-MIB
| hwConfigChangeIP |
From HUAWEI-MIB
| huaweiUtility | OBJECT-IDENTITY |
From IF-MIB
| ifIndex | OBJECT-TYPE |
From SNMPv2-SMI
| Gauge32 | |
| Integer32 | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-IDENTITY | |
| OBJECT-TYPE | |
| Unsigned32 | |
| enterprises |
From SNMPv2-TC
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TruthValue |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| hwVOPGlobalModule | 1.3.6.1.4.1.2011.6.144 | The MIB is used for xDSL Configuration according to the Vector of Profiles (VoP) data model specified in Broadband Forum Technical Report TR-165 (http://www.broadband-forum.org/technical/download/TR-165.pdf). | ||
| hwVOPObjects | 1.3.6.1.4.1.2011.6.144.1 | |||
| hwVOPProfiles | 1.3.6.1.4.1.2011.6.144.1.1 | |||
| HWV hwVOPDataRateProfileIndexNext | 1.3.6.1.4.1.2011.6.144.1.1.1 | HWVOPProfileIndexOrZeroType | read-only | This object contains an appropriate value to be used for hwVOPDataRateConfProfIndex when creating entries in the hwVOPDataRateConfProfTable. The value '0' indicates that no unassigned entries are available. To obtain the value of hwVOPDataRateConfProfIndex for a new entry in the table, the manager issues a management protocol retrieval operation. The agent will determine through its local policy when this index value will be made available for reuse. |
| hwVOPDataRateConfProfTable | 1.3.6.1.4.1.2011.6.144.1.1.2 | not-accessible | The table hwVOPDataRateConfProfTable contains data rate configuration parameters for the DSL channel(s). Entries in this table MUST be maintained in a persistent manner. Two default profiles with index numbers 1 and 2 will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document The index of this table is hwVOPDataRateConfProfIndex. | |
| hwVOPDataRateConfProfEntry | 1.3.6.1.4.1.2011.6.144.1.1.2.1 | not-accessible | The table hwVOPDataRateConfProfTable contains data rate configuration parameters for the DSL channel(s). Entries in this table MUST be maintained in a persistent manner. Two default profiles with index numbers 1 and 2 will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document The index of this entry is hwVOPDataRateConfProfIndex. | |
| U32 hwVOPDataRateConfProfIndex | 1.3.6.1.4.1.2011.6.144.1.1.2.1.1 | Unsigned32 | not-accessible | The hwVOPDataRateConfProfIndex identifies a row in the hwVOPDataRateConfProfTable. |
| ROW hwVOPDataRateConfProfRowStatus | 1.3.6.1.4.1.2011.6.144.1.1.2.1.2 | RowStatus | read-create | The hwVOPDataRateConfProfRowStatus is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'notInService'), it MUST be first unreferenced from all associated DSL lines. A row in vopDataRateProfTable is said to be unreferenced when there is no instance of hwVOPActSetupUsDataRateProfId1-4 and hwVOPActSetupDsDataRateProfId1-4 in the hwVOPActSetupTable which refers to the row. |
| OCT hwVOPDataRateConfProfDescription | 1.3.6.1.4.1.2011.6.144.1.1.2.1.3 | OCTET STRING | read-create | The hwVOPDataRateConfProfDescription contains an optional human readable description for the profile. |
| G32 hwVOPDataRateConfProfMinDataRate | 1.3.6.1.4.1.2011.6.144.1.1.2.1.4 | Gauge32 | read-create | If retransmission is not used in a given transmit direction,this parameter specifics minimum data rate for the bearer channel. The rate is coded in steps of 1000 bit/s. |
| G32 hwVOPDataRateConfProfMinResDataRate | 1.3.6.1.4.1.2011.6.144.1.1.2.1.5 | Gauge32 | read-create | The minimum reserved net data rate for the bearer channel, coded in bit/s. This parameter is only used if the Rate Adaptation Mode in the direction of the bearer channel (i.e., xdsl2LConfProfRaModeDs) is set to dynamicRa. Unit: bit/s. |
| G32 hwVOPDataRateConfProfMaxDataRate | 1.3.6.1.4.1.2011.6.144.1.1.2.1.6 | Gauge32 | read-create | If retransmission is not used in a given transmit direction,this parameter specifics maximum data rate for the bearer channel. The rate is coded in steps of 1000 bit/s. |
| G32 hwVOPDataRateConfProfMinDataRateLowPwr | 1.3.6.1.4.1.2011.6.144.1.1.2.1.7 | Gauge32 | read-create | This parameter specifies the minimum net data rate for the bearer channel as desired by the operator of the system during the low power state (L1/L2). The power management low power states L1 and L2 are defined in ITU-T Recs G.992.2 and G.992.3 respectively. The data rate is coded in steps of bit/s. Unit: bit/s. |
| XDS hwVOPDataRateConfProfMaxBer | 1.3.6.1.4.1.2011.6.144.1.1.2.1.8 | Xdsl2MaxBer | read-create | Maximum Bit Error Ratio of the bearer channel. |
| G32 hwVOPDataRateConfProfUsDataRate | 1.3.6.1.4.1.2011.6.144.1.1.2.1.9 | Gauge32 | read-create | If retransmission is not used in a given transmit direction, This parameter is a threshold on the net data rate upshift achieved over one or more bearer channel data rate adaptations. An upshift rate change alarm (event) is triggered when the actual data rate exceeds the data rate at the last entry into showtime by more than the threshold. The data rate threshold is coded in bit/s. Unit: bit/s. |
| G32 hwVOPDataRateConfProfDsDataRate | 1.3.6.1.4.1.2011.6.144.1.1.2.1.10 | Gauge32 | read-create | If retransmission is not used in a given transmit direction, This parameter is a threshold on the net data rate downshift achieved over one or more bearer channel data rate adaptations. A downshift rate change alarm (event) is triggered when the actual data rate is below the data rate at the last entry into showtime by more than the threshold. The data rate threshold is coded in bit/s. Unit: bit/s. |
| XDS hwVOPDataRateConfProfDataPathMode | 1.3.6.1.4.1.2011.6.144.1.1.2.1.11 | Xdsl2DataPathMode | read-create | The channel data path mode. |
| G32 hwVOPDataRateConfProfMinEtrRtx | 1.3.6.1.4.1.2011.6.144.1.1.2.1.12 | Gauge32 | read-create | If retransmission is used in a given transmit direction, this parameter specifies the minimum expected throughput for the bearer channel.The values range in steps of 1000 bit/s. Unit: bit/s |
| G32 hwVOPDataRateConfProfMaxEtrRtx | 1.3.6.1.4.1.2011.6.144.1.1.2.1.13 | Gauge32 | read-create | If retransmission is used in a given transmit direction, this parameter specifies the maximum expected throughput for the bearer channel.The values range in steps of 1000 bit/s. Unit: bit/s |
| G32 hwVOPDataRateConfProfMaxNdrRtx | 1.3.6.1.4.1.2011.6.144.1.1.2.1.14 | Gauge32 | read-create | If retransmission is used in a given transmit direction, this parameter specifies the maximum net data rate for the bearer channel. The values range in steps of 1000 bit/s. Unit: bit/s |
| HWV hwVOPLineSpectrumProfileIndexNext | 1.3.6.1.4.1.2011.6.144.1.1.3 | HWVOPProfileIndexOrZeroType | read-only | This object contains an appropriate value to be used for hwVOPLineSpectrumConfProfIndex when creating entries in the hwVOPLineSpectrumConfProfTable. The value '0' indicates that no unassigned entries are available. To obtain the value of hwVOPLineSpectrumConfProfIndex for a new entry in the table, the manager issues a management protocol retrieval operation. The agent will determine through its local policy when this index value will be made available for reuse. |
| hwVOPLineSpectrumConfProfTable | 1.3.6.1.4.1.2011.6.144.1.1.4 | not-accessible | The table hwVOPLineSpectrumConfProfTable contains the parameters that are mainly set during the service delivery phase, independently for upstream and downstream. Entries in this table MUST be maintained in a persistent manner. A default profile with an index of '1' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document. The index of this table is hwVOPLineSpectrumConfProfIndex. | |
| hwVOPLineSpectrumConfProfEntry | 1.3.6.1.4.1.2011.6.144.1.1.4.1 | not-accessible | The table hwVOPLineSpectrumConfProfTable contains the parameters that are mainly set during the service delivery phase, independently for upstream and downstream. Entries in this table MUST be maintained in a persistent manner. A default profile with an index of '1' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document. The index of this entry is hwVOPLineSpectrumConfProfIndex. | |
| U32 hwVOPLineSpectrumConfProfIndex | 1.3.6.1.4.1.2011.6.144.1.1.4.1.1 | Unsigned32 | not-accessible | The hwVOPLineSpectrumConfProfIndex identifies a row in the hwVOPLineSpectrumConfProfTable. |
| ROW hwVOPLineSpectrumConfProfRowStatus | 1.3.6.1.4.1.2011.6.144.1.1.4.1.2 | RowStatus | read-create | The hwVOPLineSpectrumConfProfRowStatus is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'notInService'), it MUST be first unreferenced from all associated DSL lines. A row in hwVOPLineSpectrumConfProfTable is said to be not referenced when there is no instance of hwVOPActSetupLSpectrumProfId in the hwVOPActSetupTable which refers to the row. |
| OCT hwVOPLineSpectrumConfProfDescription | 1.3.6.1.4.1.2011.6.144.1.1.4.1.3 | OCTET STRING | read-create | The hwVOPLineSpectrumConfProfDescription contains an optional human readable description for the profile. |
| XDS hwVOPLineSpectrumConfProfXtuTransSysEna | 1.3.6.1.4.1.2011.6.144.1.1.4.1.4 | Xdsl2TransmissionModeType | read-create | xTU Transmission System Enabling (XTSE). A list of the different coding types enabled in this profile. It is coded in a bit-map representation with 1 or more bits set. A bit set to '1' means that the xTUs may apply the respective coding for the DSL line. A bit set to '0' means that the xTUs cannot apply the respective coding for the xDSL line. All 'reserved' bits should be set to '0'. |
| XDS hwVOPLineSpectrumConfProfPmMode | 1.3.6.1.4.1.2011.6.144.1.1.4.1.5 | Xdsl2LinePmMode | read-create | Power management state Enabling (PMMode). Defines the power states the xTU-C or xTU-R may autonomously transition to on this line. This is a set of bits, where any bit with a '1' value means that the xTU is allowed to transit into the respective state and any bit with a '0' value means that the xTU is not allowed to transit into the respective state. |
| G32 hwVOPLineSpectrumConfProfL0Time | 1.3.6.1.4.1.2011.6.144.1.1.4.1.6 | Gauge32 | read-create | The minimum time (in seconds) between an Exit from the L2 state and the next Entry into the L2 state. Unit: seconds. |
| G32 hwVOPLineSpectrumConfProfL2Time | 1.3.6.1.4.1.2011.6.144.1.1.4.1.7 | Gauge32 | read-create | The minimum time (in seconds) between an Entry into the L2 state and the first Power Trim in the L2 state and between two consecutive Power Trims in the L2 State. Unit: seconds |
| G32 hwVOPLineSpectrumConfProfL3Time | 1.3.6.1.4.1.2011.6.144.1.1.4.1.8 | Gauge32 | read-create | This minimum time (in seconds) between an Entry into the L3 state and the L0 or L2 state. Unit: seconds |
| G32 hwVOPLineSpectrumConfProfL2Atpr | 1.3.6.1.4.1.2011.6.144.1.1.4.1.9 | Gauge32 | read-create | The maximum aggregate transmit power reduction (in dB) that can be performed at transition of L0 to L2 state or through a single Power Trim in the L2 state. Unit: dB. |
| G32 hwVOPLineSpectrumConfProfL2Atprt | 1.3.6.1.4.1.2011.6.144.1.1.4.1.10 | Gauge32 | read-create | The total maximum aggregate transmit power reduction (in dB) that can be performed in an L2 state. This is the sum of all reductions of L2 Request (i.e., at transition of L0 to L2 state) and Power Trims. Unit: dB. |
| XDS hwVOPLineSpectrumConfProfReferenceClock | 1.3.6.1.4.1.2011.6.144.1.1.4.1.11 | Xdsl2LineClockReferenceType | read-create | This object configures the clock reference for the ATU-C in a VDSL Line. |
| XDS hwVOPLineSpectrumConfProfBitSwapDs | 1.3.6.1.4.1.2011.6.144.1.1.4.1.12 | Xdsl2BitSwap | read-create | Enable or disable the bit swap downstream of a line. |
| XDS hwVOPLineSpectrumConfProfBitSwapUs | 1.3.6.1.4.1.2011.6.144.1.1.4.1.13 | Xdsl2BitSwap | read-create | Enable or disable the bit swap upstream of a line. |
| XDS hwVOPLineSpectrumConfProfScMaskDs | 1.3.6.1.4.1.2011.6.144.1.1.4.1.14 | Xdsl2ScMaskDs | read-create | Downstream subcarriers mask. A bitmap of 512 bits that allows masking up to 512 downstream subcarriers. If bit i (0 <= i < NSCds) is set to '1', the respective downstream subcarrier is masked, and if set to '0', the respective subcarrier is unmasked. Note that there should always be unmasked subcarriers (i.e.,this object cannot be all 1's). Also note that if NSCds < 512, all bits i(NSCds < i <= 512) should be set to '1'. NSCds is the highest subcarrier index that can be transmitted in the downstream direction. For G.992.3, G.992.4, and G.992.5, it is defined in the corresponding Recommendations. For G.992.1, NSCds = 256 and for G.992.2, NSCds = 128. |
| XDS hwVOPLineSpectrumConfProfScMaskUs | 1.3.6.1.4.1.2011.6.144.1.1.4.1.15 | Xdsl2ScMaskUs | read-create | Upstream subcarriers mask. A bitmap of 512 bits that allows masking up to 512 downstream subcarriers. If bit i (0 <= i < NSCds) is set to '1', the respective downstream subcarrier is masked, and if set to '0', the respective subcarrier is unmasked. Note that there should always be unmasked subcarriers (i.e.,this object cannot be all 1's). Also note that if NSCds < 512, all bits i(NSCds < i <= 512) should be set to '1'. NSCus is the highest subcarrier index that can be transmitted in the upstream direction. For G.992.3, G.992.4, and G.992.5, it is defined in the corresponding Recommendation. For Annex A/G.992.1 and G.992.2, NSCus = 32 and for Annex B/G.992.1, NSCus = 64. |
| XDS hwVOPLineSpectrumConfProfVdsl2CarMask | 1.3.6.1.4.1.2011.6.144.1.1.4.1.16 | Xdsl2CarMask | read-create | VDSL2 specific subcarriers mask. This configuration parameter defines the restrictions, additional to the band plan, to determine the set of subcarriers allowed for transmission in both upstream and downstream directions. The parameter shall describe the not masked subcarriers as one or more frequency bands. Each band is represented by start and stop subcarrier indices with a subcarrier spacing of 4.3125kHz. The valid range of subcarrier indices runs from 0 to at least the index of the highest allowed subcarrier in both transmission directions among all profiles enabled by the parameter hwVOPLineSpectrumConfProfProfiles. Up to 32 bands may be specified. Other subcarriers shall be masked. |
| G32 hwVOPLineSpectrumConfProfMsgMinUs | 1.3.6.1.4.1.2011.6.144.1.1.4.1.17 | Gauge32 | read-create | Minimum Overhead Rate Upstream. Defines the minimum rate of the message-based overhead that shall be maintained by the xTU in upstream direction. Expressed in bits per second and ranges from 4000 to 248000 bps. Unit: bits/second. |
| G32 hwVOPLineSpectrumConfProfMsgMinDs | 1.3.6.1.4.1.2011.6.144.1.1.4.1.18 | Gauge32 | read-create | Minimum Overhead Rate Downstream. Defines the minimum rate of the message-based overhead that shall be maintained by the xTU in downstream direction. Expressed in bits per second and ranges from 4000 to 248000 bps. Unit: bits/second. |
| XDS hwVOPLineSpectrumConfProfProfiles | 1.3.6.1.4.1.2011.6.144.1.1.4.1.19 | Xdsl2LineProfiles | read-create | The configuration parameter contains the G.993.2 profiles to be allowed by the near-end xTU on this line. It is coded in a bitmap representation (0 if not allowed, 1 if allowed). |
| XDS hwVOPLineSpectrumConfProfUs0Mask | 1.3.6.1.4.1.2011.6.144.1.1.4.1.20 | Xdsl2LineUs0Mask | read-create | The configuration parameter contains the US0 PSD masks to be allowed by the near-end xTU on the line. This parameter is only defined for G.993.2 Annex A. It is represented as a bitmap (0 if not allowed and 1 if allowed). |
| XDS hwVOPLineSpectrumConfProfCeFlag | 1.3.6.1.4.1.2011.6.144.1.1.4.1.21 | Xdsl2LineCeFlag | read-create | This parameter is a bit that enables the use of the optional cyclic extension values. |
| OCT hwVOPLineSpectrumConfProfModeSpecificPSDProfilesUsed | 1.3.6.1.4.1.2011.6.144.1.1.4.1.22 | OCTET STRING | read-create | The value of this object represents a pointer to one or more rows in the hwVOPModeSpecificPSDConfProfTable. The number of pointers equals to the xDSL modes enabled in hwVOPLineSpectrumConfProfXtuTransSysEna. The following rule applies: Every Octet addresses a xDSL mode (represented by one Bit in hwVOPLineSpectrumConfProfXtuTransSysEna). The value identifies the specific profile in the hwVOPModeSpecificPSDConfProfTable which applies for the specific mode. The value '0' means that no profile applies because the respective mode is not enabled. Each transmission mode enabled (hwVOPLineSpectrumConfProfXtuTransSysEna) in the hwVOPLineSpectrumConfProfTable is covered by one and only one of the Mode Specific PSD Profiles contained in that Line Spectrum Profile. |
| T/F hwVOPLineSpectrumConfProfForceInpDs | 1.3.6.1.4.1.2011.6.144.1.1.4.1.23 | TruthValue | read-create | If retransmission is not used in a given transmit direction,this parameter indicates that the framer settings of the downstream bearer shall be selected such that the impulse noise protection computed according to the formula specified in the relevant Recommendation is greater than or equal to the minimal impulse noise protection requirement. This flag shall have the same value for all the bearers of one line in the same direction. |
| T/F hwVOPLineSpectrumConfProfForceInpUs | 1.3.6.1.4.1.2011.6.144.1.1.4.1.24 | TruthValue | read-create | If retransmission is not used in a given transmit direction,this parameter indicates that the framer settings of the upstream bearer shall be selected such that the impulse noise protection computed according to the formula specified in the relevant Recommendation is greater than or equal to the minimal impulse noise protection requirement. This flag shall have the same value for all the bearers of one line in the same direction. |
| INT hwVOPLineSpectrumConfProfRtxModeDs | 1.3.6.1.4.1.2011.6.144.1.1.4.1.25 | INTEGER | read-create | The mode of operation of G.998.4 retransmission in downstream direction. Options: 1. forbidden (0) - G.998.4 retransmission not allowed. 2. preferred (1) - G.998.4 retransmission is preferred. 3. forced (2) - Force the use of the G.998.4 retransmission. 4. testmode (3) - Force the use of the G.998.4 retransmission in test mode. |
| INT hwVOPLineSpectrumConfProfRtxModeUs | 1.3.6.1.4.1.2011.6.144.1.1.4.1.26 | INTEGER | read-create | The mode of operation of G.998.4 retransmission in upstream direction. Options: 1. forbidden (0) - G.998.4 retransmission not allowed. 2. preferred (1) - G.998.4 retransmission is preferred. 3. forced (2) - Force the use of the G.998.4 retransmission. 4. testmode (3) - Force the use of the G.998.4 retransmission in test mode. |
| G32 hwVOPLineSpectrumConfProfLeftrThreshDs | 1.3.6.1.4.1.2011.6.144.1.1.4.1.27 | Gauge32 | read-create | If retransmission is used in downstream direction, this parameter specifies the threshold for declaring a near-end leftr defect. The value is coded as a fraction of the NDR with valid range from 0.01 to 0.99 with increments of 0.01. A special value means the ETR shall be used as the default threshold for declaring a leftr defect. |
| G32 hwVOPLineSpectrumConfProfLeftrThreshUs | 1.3.6.1.4.1.2011.6.144.1.1.4.1.28 | Gauge32 | read-create | If retransmission is used in upstream direction, this parameter specifies the threshold for declaring a near-end leftr defect. The value is coded as a fraction of the NDR with valid range from 0.01 to 0.99 with increments of 0.01. A special value means the ETR shall be used as the default threshold for declaring a leftr defect. |
| HWV hwVOPModeSpecificPSDProfileIndexNext | 1.3.6.1.4.1.2011.6.144.1.1.5 | HWVOPProfileIndexOrZeroType | read-only | This object contains an appropriate value to be used for hwVOPModeSpecificPSDConfProfIndex when creating entries in the hwVOPModeSpecificPSDConfProfTable. The value '0' indicates that no unassigned entries are available. To obtain the value of hwVOPModeSpecificPSDConfProfIndex for a new entry in the table, the manager issues a management protocol retrieval operation. The agent will determine through its local policy when this index value will be made available for reuse. |
| hwVOPModeSpecificPSDConfProfTable | 1.3.6.1.4.1.2011.6.144.1.1.6 | not-accessible | The table hwVOPModeSpecificPSDConfProfTable contains the parameters that define the downstream and upstream PSDs for a specific xDSL mode. Entries in this table MUST be maintained in a persistent manner. A default profile with an index of '1' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document. The index of this table is hwVOPModeSpecificPSDConfProfIndex. | |
| hwVOPModeSpecificPSDConfProfEntry | 1.3.6.1.4.1.2011.6.144.1.1.6.1 | not-accessible | The table hwVOPModeSpecificPSDConfProfTable contains the parameters that define the downstream and upstream PSDs for a specific xDSL mode. Entries in this table MUST be maintained in a persistent manner. A default profile with an index of '1' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document. The index of this entry is hwVOPModeSpecificPSDConfProfIndex. | |
| U32 hwVOPModeSpecificPSDConfProfIndex | 1.3.6.1.4.1.2011.6.144.1.1.6.1.1 | Unsigned32 | not-accessible | The hwVOPModeSpecificPSDConfProfIndex identifies a row in the hwVOPModeSpecificPSDConfProfTable. |
| ROW hwVOPModeSpecificPSDConfProfRowStatus | 1.3.6.1.4.1.2011.6.144.1.1.6.1.2 | RowStatus | read-create | This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'notInService'), it MUST be first unreferenced from all associated DSL lines. A row in hwVOPModeSpecificPSDConfProfTable is said to be unreferenced when there is no instance of hwVOPLineSpectrumConfProfModeSpecificPSDProfilesUsed in the hwVOPLineSpectrumConfProfTable which refers to the row. |
| OCT hwVOPModeSpecificPSDConfProfDescription | 1.3.6.1.4.1.2011.6.144.1.1.6.1.3 | OCTET STRING | read-create | The hwVOPModeSpecificPSDConfProfDescription contains an optional human readable description for the profile. |
| XDS hwVOPModeSpecificPSDConfProfXdslMode | 1.3.6.1.4.1.2011.6.144.1.1.6.1.4 | Xdsl2TransmissionModeType | read-create | A list of the different xDSL modes enabled in this profile. It is coded in a bit-map representation with 1 or more bits set. A bit set to '1' means that the profile applies to the respective xDSL Mode. A bit set to '0' means that the profile does not apply to the respective xDSL Mode. All 'reserved' bits should be set to '0'. This object is deprecated in favour of hwVOPLineSpectrumConfProfXtuTransSysEna. |
| I32 hwVOPModeSpecificPSDConfProfMaxNomPsdDs | 1.3.6.1.4.1.2011.6.144.1.1.6.1.5 | Integer32 | read-create | The maximum nominal transmit PSD in the downstream direction during initialization and Showtime. It ranges from -600 to -300 units of 0.1 dBm/Hz (physical values are -60 to -30 dBm/Hz). Unit: 0.1 dBm/Hz. |
| I32 hwVOPModeSpecificPSDConfProfMaxNomPsdUs | 1.3.6.1.4.1.2011.6.144.1.1.6.1.6 | Integer32 | read-create | The maximum nominal transmit PSD in the upstream direction during initialization and Showtime. It ranges from -600 to -300 units of 0.1 dBm/Hz (physical values are -60 to -30 dBm/Hz). Unit: 0.1 dBm/Hz. |
| G32 hwVOPModeSpecificPSDConfProfMaxNomAtpDs | 1.3.6.1.4.1.2011.6.144.1.1.6.1.7 | Gauge32 | read-create | The maximum nominal aggregate transmit power in the downstream direction during initialization and Showtime. It ranges from 0 to 255 units of 0.1 dBm (physical values are 0 to 25.5 dBm). Unit: 0.1 dBm. |
| G32 hwVOPModeSpecificPSDConfProfMaxNomAtpUs | 1.3.6.1.4.1.2011.6.144.1.1.6.1.8 | Gauge32 | read-create | The maximum nominal aggregate transmit power in the upstream direction during initialization and Showtime. It ranges from 0 to 255 units of 0.1 dBm (physical values are 0 to 25.5 dBm). Unit: 0.1 dBm. |
| I32 hwVOPModeSpecificPSDConfProfaxAggRxPwrUs | 1.3.6.1.4.1.2011.6.144.1.1.6.1.9 | Integer32 | read-create | The maximum upstream aggregate receive power over the relevant set of subcarriers. The xTU-C should verify that the upstream power cutback is such that this maximum aggregate receive power value is honored. It ranges from -255 to 255 units of 0.1 dBm (physical values are -25.5 to 25.5 dBm). A value of 0x7FFFFFFF (2147483647) means that there is no limit. Unit: 0.1 dBm. |
| XDS hwVOPModeSpecificPSDConfProfPsdMaskDs | 1.3.6.1.4.1.2011.6.144.1.1.6.1.10 | Xdsl2PsdMaskDs | read-create | The downstream PSD mask applicable at the U-R2 reference point. This parameter may impose PSD restrictions (breakpoints) in addition to the Limit PSD mask defined in the relevant Recommendation (e.g., ITU-T Recs G.992.5 and G.993.2). This is a string of 32 pairs of values in the following structure: Octets 0-1 - Index of 1st subcarrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the subcarrier indicated in octets 0 and 1. Octets 3-5 - Same, for a 2nd breakpoint. Octets 6-8 - Same, for a 3rd breakpoint. This architecture continues until octets 94-95, which are associated with a 32nd breakpoint. Each subcarrier index is an unsigned number in the range 0 and NSCds-1. Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are in the range 0 to 190 (0 to -95dBm/Hz). When the number of breakpoints is less than 32, all remaining octets are set to the value 0. Note that the content of this object should be correlated with the subcarriers mask and with the RFI setup. |
| XDS hwVOPModeSpecificPSDConfProfPsdMaskUs | 1.3.6.1.4.1.2011.6.144.1.1.6.1.11 | Xdsl2PsdMaskUs | read-create | The upstream PSD mask applicable at the U-R2 reference point. This parameter may impose PSD restrictions (breakpoints) in addition to the Limit PSD mask defined in the relevant Recommendation (e.g., ITU-T Recs G.992.5 and G.993.2). This is a string of 16 pairs of values in the following structure: Octets 0-1 - Index of 1st subcarrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the subcarrier indicated in octets 0 and 1. Octets 3-5 - Same, for a 2nd breakpoint. Octets 6-8 - Same, for a 3rd breakpoint. This architecture continues until octets 9-47, which are associated with a 16th breakpoint. Each subcarrier index is an unsigned number in the range 0 and NSCus-1. Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are in the range 0 to 190 (0 to -95dBm/Hz). When the number of breakpoints is less than 16, all remaining octets are set to the value 0. Note that the content of this object should be correlated with the subcarriers mask and with the RFI setup. |
| XDS hwVOPModeSpecificPSDConfProfPsdMaskSelectUs | 1.3.6.1.4.1.2011.6.144.1.1.6.1.12 | Xdsl2LinePsdMaskSelectUs | read-create | The selected upstream PSD mask. This parameter is used only for Annexes J and M of G.992.3 and G.992.5, and the same selection is used for all relevant enabled bits in hwVOPLineSpectrumConfProfXtuTransSysEna. |
| XDS hwVOPModeSpecificPSDConfProfLimitMask | 1.3.6.1.4.1.2011.6.144.1.1.6.1.13 | Xdsl2LineLimitMask | read-create | This configuration parameter contains the G.993.2 limit PSD masks of the selected PSD mask class, enabled by the near-end xTU on this line for each class of profiles. This parameter is defined per VDSL2 Annex enabled in the xdsl2LConfProfXtuTransSysEna object. Through this parameter, several limit PSD masks of the selected PSD mask class (hwVOPModeSpecificPSDConfProfClassMask) may be enabled. The enabling parameter is coded in a bitmap representation (0 if the associated mask is not allowed, 1 if it is allowed). |
| XDS hwVOPModeSpecificPSDConfProfUs0Disable | 1.3.6.1.4.1.2011.6.144.1.1.6.1.14 | Xdsl2LineUs0Disable | read-create | This configuration parameter indicates if the use of US0 is disabled for each limit PSD mask enabled in the hwVOPModeSpecificPSDConfProfLimitMask parameter. This parameter is defined per VDSL2 Annex enabled in the hwVOPLineSpectrumConfProfXtuTransSysEna object. For each limit PSD mask enabled in hwVOPModeSpecificPSDConfProfLimitMask parameter, a bit shall indicate if US0 is disabled. The disabling parameter is coded as a bitmap. The bit is set to 1 if US0 is disabled for the associated limit mask. This parameter and the hwVOPModeSpecificPSDConfProfLimitMask parameter use the same structure. |
| XDS hwVOPModeSpecificPSDConfProfClassMask | 1.3.6.1.4.1.2011.6.144.1.1.6.1.15 | Xdsl2LineClassMask | read-create | In order to reduce the number of configuration possibilities, the limit Power Spectral Density masks (see hwVOPModeSpecificPSDConfProfLimitMask) are grouped in PSD mask classes. Each class is designed such that the PSD levels of each limit PSD mask of a specific class are equal in their respective passband above 552 kHz. This parameter is defined per VDSL2 Annex enabled in the hwVOPLineSpectrumConfProfXtuTransSysEna object. It selects a single PSD mask class per Annex that is activated at the VTU-O. |
| HWV hwVOPUPBOProfileIndexNext | 1.3.6.1.4.1.2011.6.144.1.1.7 | HWVOPProfileIndexOrZeroType | read-only | This object contains an appropriate value to be used for hwVOPUPBOConfProfIndex when creating entries in the hwVOPUPBOConfProfTable. The value '0' indicates that no unassigned entries are available. To obtain the value of hwVOPUPBOConfProfIndex for a new entry in the table, the manager issues a management protocol retrieval operation. The agent will determine through its local policy when this index value will be made available for reuse. |
| hwVOPUPBOConfProfTable | 1.3.6.1.4.1.2011.6.144.1.1.8 | not-accessible | The table hwVOPUPBOConfProfTable contains all the parameters related to upstream power back-off. Entries in this table MUST be maintained in a persistent manner. A default profile with an index of '1' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document. The index of this table is hwVOPUPBOConfProfIndex. | |
| hwVOPUPBOConfProfEntry | 1.3.6.1.4.1.2011.6.144.1.1.8.1 | not-accessible | The table hwVOPUPBOConfProfTable contains all the parameters related to upstream power back-off. Entries in this table MUST be maintained in a persistent manner. A default profile with an index of '1' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document. The index of this entry is hwVOPUPBOConfProfIndex. | |
| U32 hwVOPUPBOConfProfIndex | 1.3.6.1.4.1.2011.6.144.1.1.8.1.1 | Unsigned32 | not-accessible | The hwVOPUPBOConfProfIndex identifies a row in the hwVOPUPBOConfProfTable. |
| ROW hwVOPUPBOConfProfRowStatus | 1.3.6.1.4.1.2011.6.144.1.1.8.1.2 | RowStatus | read-create | This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'notInService'), it MUST be first unreferenced from all associated DSL lines. A row in hwVOPUPBOConfProfTable is said to be unreferenced when there is no instance of hwVOPActSetupUpboProfId in the hwVOPActSetupTable which refers to the row. |
| OCT hwVOPUPBOConfProfDescription | 1.3.6.1.4.1.2011.6.144.1.1.8.1.3 | OCTET STRING | read-create | The hwVOPUPBOConfProfDescription contains an optional human readable description for the profile. |
| G32 hwVOPUPBOConfProfUpboKL | 1.3.6.1.4.1.2011.6.144.1.1.8.1.4 | Gauge32 | read-create | This configuration parameter defines the electrical length expressed in dB at 1MHz, kl0, configured by the CO-MIB.The value ranges from 0 (coded as 0) to 128 dB (coded as 1280) in steps of 0.1 dB. This parameter is relevant only if hwVOPUPBOConfProfUpboKLF is set to override(2), which indicates that this parameter's value will override the VTUs' determination of the electrical length. If hwVOPUPBOConfProfUpboKLF is set either to auto(1) or disableUpbo(3), then this parameter will be ignored. Unit: 0.1 dB. |
| XDS hwVOPUPBOConfProfUpboKLF | 1.3.6.1.4.1.2011.6.144.1.1.8.1.5 | Xdsl2UpboKLF | read-create | Defines the upstream power backoff force mode. |
| U32 hwVOPUPBOConfProfKlAuto | 1.3.6.1.4.1.2011.6.144.1.1.8.1.6 | Unsigned32 | read-create | This parameter defines the mode in which kl0 is computed when hwVOPUPBOConfProfUpboKLF is auto. Options: 1--max(kl0_CO,kl0_CPE) 2--min(kl0_CO,kl0_CPE) 3--kl0_CO 4--kl0_CPE |
| I32 hwVOPUPBOConfProfPsdAUs1 | 1.3.6.1.4.1.2011.6.144.1.1.8.1.7 | Integer32 | read-create | This configuration parameter defines the 'a' reference parameter of the UPBO reference PSD used to compute the upstream power back-off for the upstream band US1. A UPBOPSD defined for each band shall consist of two parameters [a, b]. Parameter 'a' ranges from 40 dBm/Hz (coded as 4000) to 80.95 dBm/Hz (coded as 8095) in steps of 0.01 dBm/Hz; and parameter 'b' ranges from 0 dBm/Hz (coded as 0) to 40.95 dBm/Hz (coded as 4095) in steps of 0.01 dBm/Hz. The UPBO reference PSD at the frequency 'f' expressed in MHz shall be equal to '-a-b(SQRT(f))'. Setting hwVOPUPBOConfProfPsdAUs1 to 4000 and hwVOPUPBOConfProfPsdBUs1 to 0 is a special configuration to disable UPBO in the respective upstream band. Unit: 0.01 dBm/Hz. |
| I32 hwVOPUPBOConfProfPsdBUs1 | 1.3.6.1.4.1.2011.6.144.1.1.8.1.8 | Integer32 | read-create | This configuration parameter defines the 'b' reference parameter of the UPBO reference PSD used to compute the upstream power back-off for the upstream band US1. A UPBOPSD defined for each band shall consist of two parameters [a, b]. Parameter 'a' ranges from 40 dBm/Hz (coded as 4000) to 80.95 dBm/Hz (coded as 8095) in steps of 0.01 dBm/Hz; and parameter 'b' ranges from 0 dBm/Hz (coded as 0) to 40.95 dBm/Hz (coded as 4095) in steps of 0.01 dBm/Hz. The UPBO reference PSD at the frequency 'f' expressed in MHz shall be equal to '-a-b(SQRT(f))'. Setting hwVOPUPBOConfProfPsdAUs1 to 4000 and hwVOPUPBOConfProfPsdBUs1 to 0 is a special configuration to disable UPBO in the respective upstream band. Unit: 0.01 dBm/Hz. |
| I32 hwVOPUPBOConfProfPsdAUs2 | 1.3.6.1.4.1.2011.6.144.1.1.8.1.9 | Integer32 | read-create | This configuration parameter defines the 'a' reference parameter of the UPBO reference PSD used to compute the upstream power back-off for the upstream band US2. A UPBOPSD defined for each band shall consist of two parameters [a, b]. Parameter 'a' ranges from 40 dBm/Hz (coded as 4000) to 80.95 dBm/Hz (coded as 8095) in steps of 0.01 dBm/Hz; and parameter 'b' ranges from 0 dBm/Hz (coded as 0) to 40.95 dBm/Hz (coded as 4095) in steps of 0.01 dBm/Hz. The UPBO reference PSD at the frequency 'f' expressed in MHz shall be equal to '-a-b(SQRT(f))'. Setting hwVOPUPBOConfProfPsdAUs2 to 4000 and hwVOPUPBOConfProfPsdBUs2 to 0 is a special configuration to disable UPBO in the respective upstream band. Unit: 0.01 dBm/Hz. |
| I32 hwVOPUPBOConfProfPsdBUs2 | 1.3.6.1.4.1.2011.6.144.1.1.8.1.10 | Integer32 | read-create | This configuration parameter defines the 'b' reference parameter of the UPBO reference PSD used to compute the upstream power back-off for the upstream band US2. A UPBOPSD defined for each band shall consist of two parameters [a, b]. Parameter 'a' ranges from 40 dBm/Hz (coded as 4000) to 80.95 dBm/Hz (coded as 8095) in steps of 0.01 dBm/Hz; and parameter 'b' ranges from 0 dBm/Hz (coded as 0) to 40.95 dBm/Hz (coded as 4095) in steps of 0.01 dBm/Hz. The UPBO reference PSD at the frequency 'f' expressed in MHz shall be equal to '-a-b(SQRT(f))'. Setting hwVOPUPBOConfProfPsdAUs2 to 4000 and hwVOPUPBOConfProfPsdBUs2 to 0 is a special configuration to disable UPBO in the respective upstream band. Unit: 0.01 dBm/Hz. |
| I32 hwVOPUPBOConfProfPsdAUs3 | 1.3.6.1.4.1.2011.6.144.1.1.8.1.11 | Integer32 | read-create | This configuration parameter defines the 'a' reference parameter of the UPBO reference PSD used to compute the upstream power back-off for the upstream band US3. A UPBOPSD defined for each band shall consist of two parameters [a, b]. Parameter 'a' ranges from 40 dBm/Hz (coded as 4000) to 80.95 dBm/Hz (coded as 8095) in steps of 0.01 dBm/Hz; and parameter 'b' ranges from 0 dBm/Hz (coded as 0) to 40.95 dBm/Hz (coded as 4095) in steps of 0.01 dBm/Hz. The UPBO reference PSD at the frequency 'f' expressed in MHz shall be equal to '-a-b(SQRT(f))'. Setting hwVOPUPBOConfProfPsdAUs3 to 4000 and hwVOPUPBOConfProfPsdBUs3 to 0 is a special configuration to disable UPBO in the respective upstream band. Unit: 0.01 dBm/Hz. |
| I32 hwVOPUPBOConfProfPsdBUs3 | 1.3.6.1.4.1.2011.6.144.1.1.8.1.12 | Integer32 | read-create | This configuration parameter defines the 'b' reference parameter of the UPBO reference PSD used to compute the upstream power back-off for the upstream band US3. A UPBOPSD defined for each band shall consist of two parameters [a, b]. Parameter 'a' ranges from 40 dBm/Hz (coded as 4000) to 80.95 dBm/Hz (coded as 8095) in steps of 0.01 dBm/Hz; and parameter 'b' ranges from 0 dBm/Hz (coded as 0) to 40.95 dBm/Hz (coded as 4095) in steps of 0.01 dBm/Hz. The UPBO reference PSD at the frequency 'f' expressed in MHz shall be equal to '-a-b(SQRT(f))'. Setting hwVOPUPBOConfProfPsdAUs3 to 4000 and hwVOPUPBOConfProfPsdBUs3 to 0 is a special configuration to disable UPBO in the respective upstream band. Unit: 0.01 dBm/Hz. |
| I32 hwVOPUPBOConfProfPsdAUs4 | 1.3.6.1.4.1.2011.6.144.1.1.8.1.13 | Integer32 | read-create | This configuration parameter defines the 'a' reference parameter of the UPBO reference PSD used to compute the upstream power back-off for the upstream band US4. A UPBOPSD defined for each band shall consist of two parameters [a, b]. Parameter 'a' ranges from 40 dBm/Hz (coded as 4000) to 80.95 dBm/Hz (coded as 8095) in steps of 0.01 dBm/Hz; and parameter 'b' ranges from 0 dBm/Hz (coded as 0) to 40.95 dBm/Hz (coded as 4095) in steps of 0.01 dBm/Hz. The UPBO reference PSD at the frequency 'f' expressed in MHz shall be equal to '-a-b(SQRT(f))'. Setting hwVOPUPBOConfProfPsdAUs4 to 4000 and hwVOPUPBOConfProfPsdBUs4 to 0 is a special configuration to disable UPBO in the respective upstream band. Unit: 0.01 dBm/Hz. |
| I32 hwVOPUPBOConfProfPsdBUs4 | 1.3.6.1.4.1.2011.6.144.1.1.8.1.14 | Integer32 | read-create | This configuration parameter defines the 'b' reference parameter of the UPBO reference PSD used to compute the upstream power back-off for the upstream band US4. A UPBOPSD defined for each band shall consist of two parameters [a, b]. Parameter 'a' ranges from 40 dBm/Hz (coded as 4000) to 80.95 dBm/Hz (coded as 8095) in steps of 0.01 dBm/Hz; and parameter 'b' ranges from 0 dBm/Hz (coded as 0) to 40.95 dBm/Hz (coded as 4095) in steps of 0.01 dBm/Hz. The UPBO reference PSD at the frequency 'f' expressed in MHz shall be equal to '-a-b(SQRT(f))'. Setting hwVOPUPBOConfProfPsdAUs4 to 4000 and hwVOPUPBOConfProfPsdBUs4 to 0 is a special configuration to disable UPBO in the respective upstream band. Unit: 0.01 dBm/Hz. |
| XDS hwVOPUPBOConfProfBoostMode | 1.3.6.1.4.1.2011.6.144.1.1.8.1.15 | Xdsl2UpboBoostMode | read-create | The Equalized FEXT UPBO method. Options: 1. disable(1) - The Equalized FEXT UPBO method is not supported. 2. enable(2) - The Equalized FEXT UPBO method is supported. |
| I32 hwVOPUPBOConfProfUpboKLREFUs1 | 1.3.6.1.4.1.2011.6.144.1.1.8.1.16 | Integer32 | read-create | This parameter defines the UPBO reference electrical length used to compute the upstream power back-off for the upstream band US1, for the optional Equalized FEXT UPBO method. The value ranges from 1.8 to 63.5 dB in steps of 0.1 dB with special value 0. The use of the special value 0 is described in 7.2.1.3.2/G.993.2. Unit: 0.1 dB. |
| I32 hwVOPUPBOConfProfUpboKLREFUs2 | 1.3.6.1.4.1.2011.6.144.1.1.8.1.17 | Integer32 | read-create | This parameter defines the UPBO reference electrical length used to compute the upstream power back-off for the upstream band US2, for the optional Equalized FEXT UPBO method. The value ranges from 1.8 to 63.5 dB in steps of 0.1 dB with special value 0. The use of the special value 0 is described in 7.2.1.3.2/G.993.2. Unit: 0.1 dB. |
| I32 hwVOPUPBOConfProfUpboKLREFUs3 | 1.3.6.1.4.1.2011.6.144.1.1.8.1.18 | Integer32 | read-create | This parameter defines the UPBO reference electrical length used to compute the upstream power back-off for the upstream band US3, for the optional Equalized FEXT UPBO method. The value ranges from 1.8 to 63.5 dB in steps of 0.1 dB with special value 0. The use of the special value 0 is described in 7.2.1.3.2/G.993.2. Unit: 0.1 dB. |
| I32 hwVOPUPBOConfProfUpboKLREFUs4 | 1.3.6.1.4.1.2011.6.144.1.1.8.1.19 | Integer32 | read-create | This parameter defines the UPBO reference electrical length used to compute the upstream power back-off for the upstream band US4, for the optional Equalized FEXT UPBO method. The value ranges from 1.8 to 63.5 dB in steps of 0.1 dB with special value 0. The use of the special value 0 is described in 7.2.1.3.2/G.993.2. Unit: 0.1 dB. |
| U32 hwVOPUPBOConfProfAeleMode | 1.3.6.1.4.1.2011.6.144.1.1.8.1.20 | Unsigned32 | read-create | This parameter defines the UPBO electrical length estimation mode to be used in the Alternative Electrical Length Estimation method (ELE-M1) in 7.2.1.3.2.2/G.993.2. The value of this parameter is 0, 1, 2 or 3. 0-ELE_M0, 1-ELE_DS, 2-ELE_PB, 3-ELE_MIN |
| U32 hwVOPUPBOConfProfUpboElmt | 1.3.6.1.4.1.2011.6.144.1.1.8.1.21 | Unsigned32 | read-create | This parameter defines the UPBO electrical length minimum threshold percentile in percent used in the Alternative Electrical Length Estimation method (ELE-M1) in clause 7.2.1.3.2.2/G.993.2. It is set by network management via the CO-MIB. The parameter ranges from 0 to 15 percent in steps of 1 percent. This value is communicated to the VTU-R via G.994.1 at start-up. |
| HWV hwVOPDPBOProfileIndexNext | 1.3.6.1.4.1.2011.6.144.1.1.9 | HWVOPProfileIndexOrZeroType | read-only | This object contains an appropriate value to be used for hwVOPDPBOConfProfIndex when creating entries in the hwVOPDPBOConfProfTable. The value '0' indicates that no unassigned entries are available. To obtain the value of hwVOPDPBOConfProfIndex for a new entry in the table, the manager issues a management protocol retrieval operation. The agent will determine through its local policy when this index value will be made available for reuse. |
| hwVOPDPBOConfProfTable | 1.3.6.1.4.1.2011.6.144.1.1.10 | not-accessible | The table hwVOPDPBOConfProfTable contains all the parameters related to downstream power back-off. Entries in this table MUST be maintained in a persistent manner. A default profile with an index of '1' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document. The index of this table is hwVOPDPBOConfProfIndex. | |
| hwVOPDPBOConfProfEntry | 1.3.6.1.4.1.2011.6.144.1.1.10.1 | not-accessible | The table hwVOPDPBOConfProfTable contains all the parameters related to downstream power back-off. Entries in this table MUST be maintained in a persistent manner. A default profile with an index of '1' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document. The index of this entry is hwVOPDPBOConfProfIndex. | |
| U32 hwVOPDPBOConfProfIndex | 1.3.6.1.4.1.2011.6.144.1.1.10.1.1 | Unsigned32 | not-accessible | The hwVOPDPBOConfProfIndex identifies a row in the hwVOPDPBOConfProfTable. |
| ROW hwVOPDPBOConfProfRowStatus | 1.3.6.1.4.1.2011.6.144.1.1.10.1.2 | RowStatus | read-create | This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'notInService'), it MUST be first unreferenced from all associated DSL lines. A row in hwVOPDPBOConfProfTable is said to be not referenced when there is no instance of hwVOPActSetupDpboProfId in the hwVOPActSetupTable which refers to the row. |
| OCT hwVOPDPBOConfProfProfDescription | 1.3.6.1.4.1.2011.6.144.1.1.10.1.3 | OCTET STRING | read-create | The hwVOPDPBOConfProfProfDescription contains an optional human readable description for the profile. |
| U32 hwVOPDPBOConfProfWkMdMask | 1.3.6.1.4.1.2011.6.144.1.1.10.1.4 | Unsigned32 | read-create | This configuration parameter defines the current enabled DPBO working mode mask. DPBO working mode enabling:1-ADSL, 2-ADSL2+ 3-VDSL2. Options : 1--current enabled dpbo work mode:ADSL 2--current enabled dpbo work mode:ADSL2+ 3--current enabled dpbo work mode:ADSL,ADSL2+ 4--current enabled dpbo work mode:VDSL2 5--current enabled dpbo work mode:ADSL,VDSL2 6--current enabled dpbo work mode:ADSL2+,VDSL2 7--current enabled dpbo work mode:ADSL,ADSL2+,VDSL2 |
| G32 hwVOPDPBOConfProfEsEL | 1.3.6.1.4.1.2011.6.144.1.1.10.1.5 | Gauge32 | read-create | This configuration parameter defines the assumed electrical length of cables (E-side cables) connecting exchange based DSL services to a remote flexibility point (cabinet), that hosts the xTU-C that is subject to spectrally shaped downstream power back- off (DPBO) depending on this length. The electrical length is defined as the loss (in dB) of an equivalent length of hypothetical cable at a reference frequency defined by the network operator or in spectrum management regulations. This parameter shall be coded as an unsigned integer representing an electrical length from 0 dB (coded as 0) to 255.5 dB (coded as 511) in steps of 0.5 dB. All values in the range are valid. If this parameter is set to zero, the DPBO shall be disabled. Unit: 0.5dB. |
| U32 hwVOPDPBOConfProfEselMin | 1.3.6.1.4.1.2011.6.144.1.1.10.1.6 | Unsigned32 | read-create | DPBOESELMIN in dB is the minimum of all main cable losses for the KVz supplied when using the SOL model (expansion of a KVz and VDSL2 provision of additional KVz areas from this KVz using cross-cables to additional KVz), including the KVz at the MSAN site. This value must be adjustable as the minimum requirement via the SNMP interface in the configuration profile for each VDSL2 port, and is set individually for each MSAN site and usage. As an option, As an option, adjustment can be done for each MSAN or line card, thus taking effect for entire port groups. It is used only for determining the MUF. Unit: 0.5dB. |
| XDS hwVOPDPBOConfProfEPsd | 1.3.6.1.4.1.2011.6.144.1.1.10.1.7 | Xdsl2PsdMaskDs | read-create | This configuration parameter defines the PSD mask that is assumed to be permitted at the exchange. This parameter shall use the same format as xdsl2LConfProfPsdMaskDs (PSDMASKds). The maximum number of breakpoints for xdsl2LConfProfDpboEPsd is 16. |
| G32 hwVOPDPBOConfProfCableModelA | 1.3.6.1.4.1.2011.6.144.1.1.10.1.8 | Gauge32 | read-create | The E-side Cable Model parameter A (DPBOESCMA) of the cable model (DPBOESCM) for cables connecting exchange based DSL services to a remote flexibility point (cabinet), that hosts the xTU-C that is subject to spectrally shaped downstream power back-off (DPBO) depending on this value. The cable model is in terms of three scalars xdsl2LConfProfDpboEsCableModelA (DPBOESCMA), xdsl2LConfProfDpboEsCableModelB(DPBOESCMB), and xdsl2LConfProfDpboEsCableModelC (DPBOESCMC), that are used to estimate the frequency dependent loss of E-side cables calculated from the xdsl2LConfProfDpboEsEL (DPBOESEL) parameter. Possible values shall be coded as unsigned integers representing a scalar value from -1 (coded as 0) to 1.5 (coded as 640) in steps of 2^-8. All values in the range are valid. This parameter is used only for G.993.2. Unit: 2^-8. |
| G32 hwVOPDPBOConfProfCableModelB | 1.3.6.1.4.1.2011.6.144.1.1.10.1.9 | Gauge32 | read-create | The E-side Cable Model parameter B (DPBOESCMB) of the cable model (DPBOESCM) for cables connecting exchange based DSL services to a remote flexibility point (cabinet), that hosts the xTU-C that is subject to spectrally shaped downstream power back-off (DPBO) depending on this value. The cable model is in terms of three scalars dsl2LConfProfDpboEsCableModelA (DPBOESCMA), xdsl2LConfProfDpboEsCableModelB(DPBOESCMB), and xdsl2LConfProfDpboEsCableModelC (DPBOESCMC), that are used to estimate the frequency dependent loss of E-side cables calculated from the xdsl2LConfProfDpboEsEL (DPBOESEL) parameter. Possible values shall be coded as unsigned integers representing a scalar value from -1 (coded as 0) to 1.5 (coded as 640) in steps of 2^-8. All values in the range are valid. This parameter is used only for G.993.2. Unit: 2^-8. |
| G32 hwVOPDPBOConfProfCableModelC | 1.3.6.1.4.1.2011.6.144.1.1.10.1.10 | Gauge32 | read-create | The E-side Cable Model parameter C (DPBOESCMC) of the cable model (DPBOESCM) for cables connecting exchange based DSL services to a remote flexibility point (cabinet), that hosts the xTU-C that is subject to spectrally shaped downstream power back-off (DPBO) depending on this value. The cable model is in terms of three scalars xdsl2LConfProfDpboEsCableModelA (DPBOESCMA), xdsl2LConfProfDpboEsCableModelB(DPBOESCMB), and xdsl2LConfProfDpboEsCableModelC (DPBOESCMC), that are used to estimate the frequency dependent loss of E-side cables calculated from the xdsl2LConfProfDpboEsEL (DPBOESEL) parameter. Possible values shall be coded as unsigned integers representing a scalar value from -1 (coded as 0) to 1.5 (coded as 640) in steps of 2^-8. All values in the range are valid. This parameter is used only for G.993.2. Unit: 2^-8. |
| G32 hwVOPDPBOConfProfMus | 1.3.6.1.4.1.2011.6.144.1.1.10.1.11 | Gauge32 | read-create | This configuration parameter defines the assumed Minimum Usable receive PSD mask (in dBm/Hz) for exchange based services, used to modify parameter xdsl2LConfProfDpboFMax (DPBOFMAX) defined below [to determine the DPBO]. It shall be coded as an unsigned integer representing a PSD mask level from 0 dBm/Hz (coded as 0) to -127.5 dBm/Hz (coded as 255) in steps of 0.5 dBm/Hz. All values in the range are valid. NOTE - The PSD mask level is 3.5 dB above the signal PSD level. This parameter is used only for G.993.2. Unit: -0.5 dBm/Hz. |
| G32 hwVOPDPBOConfProfFMin | 1.3.6.1.4.1.2011.6.144.1.1.10.1.12 | Gauge32 | read-create | This configuration parameter defines the minimum frequency from which the DPBO shall be applied. It ranges from 0 kHz (coded as 0) to 8832 kHz (coded as 2048) in steps of 4.3125 kHz. This parameter is used only for G.993.2. Unit: 4.3125 kHz. |
| G32 hwVOPDPBOConfProfFMax | 1.3.6.1.4.1.2011.6.144.1.1.10.1.13 | Gauge32 | read-create | This configuration parameter defines the maximum frequency at which DPBO may be applied. It ranges from 138 kHz (coded as 32) to 29997.75 kHz (coded as 6956) in steps of 4.3125 kHz. This parameter is used only for G.993.2. Unit: 4.3125 kHz. |
| INT hwVOPDPBOConfFEXTFactor | 1.3.6.1.4.1.2011.6.144.1.1.10.1.14 | INTEGER | read-create | This configuration parameter defines the switch of the delta FEXT-factor. Options: 1. disable(1) - The switch of the delta FEXT-factor is disabled 2. enable(2) - The switch of the delta FEXT-factor is enabled |
| HWV hwVOPRFIProfileIndexNext | 1.3.6.1.4.1.2011.6.144.1.1.11 | HWVOPProfileIndexOrZeroType | read-only | This object contains an appropriate value to be used for hwVOPRFIConfProfIndex when creating entries in the hwVOPRFIConfProfTable. The value '0' indicates that no unassigned entries are available. To obtain the value of hwVOPRFIConfProfIndex for a new entry in the table, the manager issues a management protocol retrieval operation. The agent will determine through its local policy when this index value will be made available for reuse. |
| hwVOPRFIConfProfTable | 1.3.6.1.4.1.2011.6.144.1.1.12 | not-accessible | RFI notches are necessary only when radio services may be disturbed during operation, therefore this parameter should be separated from all other profiles. Entries in this table MUST be maintained in a persistent manner. A default profile with an index of '1' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document. The index of this table is hwVOPRFIConfProfIndex. | |
| hwVOPRFIConfProfEntry | 1.3.6.1.4.1.2011.6.144.1.1.12.1 | not-accessible | RFI notches are necessary only when radio services may be disturbed during operation, therefore this parameter should be separated from all other profiles. Entries in this table MUST be maintained in a persistent manner. A default profile with an index of '1' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document. The index of this entry is hwVOPRFIConfProfIndex. | |
| U32 hwVOPRFIConfProfIndex | 1.3.6.1.4.1.2011.6.144.1.1.12.1.1 | Unsigned32 | not-accessible | The hwVOPRFIConfProfIndex identifies a row in the hwVOPRFIConfProfTable. |
| ROW hwVOPRFIConfProfRowStatus | 1.3.6.1.4.1.2011.6.144.1.1.12.1.2 | RowStatus | read-create | This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'notInService'), it MUST be first unreferenced from all associated DSL lines. A row in hwVOPRFIConfProfTable is said to be unreferenced when there is no instance of hwVOPActSetupRfiProfId in the hwVOPActSetupTable which refers to the row. |
| OCT hwVOPRFIConfProfDescription | 1.3.6.1.4.1.2011.6.144.1.1.12.1.3 | OCTET STRING | read-create | The hwVOPRFIConfProfDescription contains an optional human readable description for the profile. |
| XDS hwVOPRFIConfProfRfiBands | 1.3.6.1.4.1.2011.6.144.1.1.12.1.4 | Xdsl2RfiBands | read-create | For ADSL2plus operation mode, this configuration parameter defines the subset of downstream PSD mask breakpoints, as specified in hwVOPModeSpecificPSDConfProfPsdMaskDs (PSDMASKds), that shall be used to notch an RFI band. This subset consists of pairs of consecutive subcarrier indices belonging to breakpoints: [ti; ti + 1], corresponding to the low level of the notch. The specific interpolation around these points is defined in ITU-T Rec. G.992.5. For VDSL2 operation mode, this configuration parameter defines the bands where the PSD shall be reduced as specified in ITU-T Rec. G.993.2 #7.2.1.2. Each band shall be represented by a start and stop subcarrier indices with a subcarrier spacing of 4.3125 kHz. Up to 16 bands may be specified. This parameter defines the RFI bands for both upstream and downstream directions. |
| HWV hwVOPSNRMarginProfileIndexNext | 1.3.6.1.4.1.2011.6.144.1.1.13 | HWVOPProfileIndexOrZeroType | read-only | This object contains an appropriate value to be used for hwVOPSNRMarginConfProfIndex when creating entries in the hwVOPSNRMarginConfProfTable. The value '0' indicates that no unassigned entries are available. To obtain the value of hwVOPSNRMarginConfProfIndex for a new entry in the table, the manager issues a management protocol retrieval operation. The agent will determine through its local policy when this index value will be made available for reuse. |
| hwVOPSNRMarginConfProfTable | 1.3.6.1.4.1.2011.6.144.1.1.14 | not-accessible | Noise margins are important for line robustness and need to be configured independently from other spectrum related parameters to reduce the amount of combinations. These parameters may be adjusted because of the changed disturber's impact while data rates aren't changed. Entries in this table MUST be maintained in a persistent manner. A default profile with an index of '1' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document. The index of this table is hwVOPSNRMarginConfProfIndex. | |
| hwVOPSNRMarginConfProfEntry | 1.3.6.1.4.1.2011.6.144.1.1.14.1 | not-accessible | Noise margins are important for line robustness and need to be configured independently from other spectrum related parameters to reduce the amount of combinations. These parameters may be adjusted because of the changed disturber's impact while data rates aren't changed. Entries in this table MUST be maintained in a persistent manner. A default profile with an index of '1' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document. The index of this entry is hwVOPSNRMarginConfProfIndex. | |
| U32 hwVOPSNRMarginConfProfIndex | 1.3.6.1.4.1.2011.6.144.1.1.14.1.1 | Unsigned32 | not-accessible | The hwVOPSNRMarginConfProfIndex identifies a row in the hwVOPSNRMarginConfProfTable. |
| ROW hwVOPSNRMarginConfProfRowStatus | 1.3.6.1.4.1.2011.6.144.1.1.14.1.2 | RowStatus | read-create | This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'notInService'), it MUST be first unreferenced from all associated DSL lines. A row in hwVOPSNRMarginConfProfTable is said to be unreferenced when there is no instance of hwVOPActSetupNoiseMarginProfId in the hwVOPActSetupTable which refers to the row. |
| OCT hwVOPSNRMarginConfProfDescription | 1.3.6.1.4.1.2011.6.144.1.1.14.1.3 | OCTET STRING | read-create | The hwVOPSNRMarginConfProfDescription contains an optional human readable description for the profile. |
| G32 hwVOPSNRMarginConfProfMinSnrmDs | 1.3.6.1.4.1.2011.6.144.1.1.14.1.4 | Gauge32 | read-create | The minimum Noise Margin the xTU-R receiver shall tolerate. If the noise margin falls below this level, the xTU-R shall request that the xTU-C increase the xTU-C transmit power. If an increase of xTU-C transmit power is not possible, a loss-of-margin (LOM) defect occurs, the xTU-R shall fail and attempt to re-initialize and the NMS shall be notified. The minimum noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). A value of 0 means that there is no minimum. Unit: 0.1 dB. |
| G32 hwVOPSNRMarginConfProfMinSnrmUs | 1.3.6.1.4.1.2011.6.144.1.1.14.1.5 | Gauge32 | read-create | The minimum Noise Margin the xTU-C receiver shall tolerate. If the noise margin falls below this level, the xTU-C shall request that the xTU-R increase the xTU-R transmit power. If an increase of xTU-R transmit power is not possible, a loss-of-margin (LOM) defect occurs, the xTU-C shall fail and attempt to re-initialize and the NMS shall be notified. The minimum noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). A value of 0 means that there is no minimum. Unit: 0.1 dB. |
| G32 hwVOPSNRMarginConfProfTargetSnrmDs | 1.3.6.1.4.1.2011.6.144.1.1.14.1.6 | Gauge32 | read-create | The minimum Noise Margin the xTU-R receiver shall achieve, relative to the BER requirement for each of the downstream bearer channels, to successfully complete initialization. The target noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). Unit: 0.1 dB. |
| G32 hwVOPSNRMarginConfProfTargetSnrmUs | 1.3.6.1.4.1.2011.6.144.1.1.14.1.7 | Gauge32 | read-create | The minimum Noise Margin the xTU-C receiver shall achieve, relative to the BER requirement for each of the upstream bearer channels, to successfully complete initialization. The target noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). Unit: 0.1 dB. |
| G32 hwVOPSNRMarginConfProfMaxSnrmDs | 1.3.6.1.4.1.2011.6.144.1.1.14.1.8 | Gauge32 | read-create | The maximum Noise Margin the xTU-R receiver shall try to sustain. If the Noise Margin is above this level, the xTU-R shall request that the xTU-C reduce the xTU-C transmit power to get a noise margin below this limit (if this functionality is supported). The maximum noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). A value of 0x7FFFFFFF (2147483647) means that there is no maximum. Unit: 0.1 dB. |
| G32 hwVOPSNRMarginConfProfMaxSnrmUs | 1.3.6.1.4.1.2011.6.144.1.1.14.1.9 | Gauge32 | read-create | The maximum Noise Margin the xTU-C receiver shall try to sustain. If the Noise Margin is above this level, the xTU-C shall request that the xTU-R reduce the xTU-R transmit power to get a noise margin below this limit (if this functionality is supported). The maximum noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). A value of 0x7FFFFFFF (2147483647) means that there is no maximum. Unit: 0.1 dB. |
| XDS hwVOPSNRMarginConfProfSnrModeDs | 1.3.6.1.4.1.2011.6.144.1.1.14.1.10 | Xdsl2LineSnrMode | read-create | This parameter enables the transmitter referred virtual noise in the downstream direction. The configuration parameters for virtual noise are in the hwVOPVirtualNoiseConfProfTable. |
| XDS hwVOPSNRMarginConfProfSnrModeUs | 1.3.6.1.4.1.2011.6.144.1.1.14.1.11 | Xdsl2LineSnrMode | read-create | This parameter enables the transmitter referred virtual noise in the upstream direction. The configuration parameters for virtual noise are in the hwVOPVirtualNoiseConfProfTable. |
| XDS hwVOPSNRMarginConfProfRaModeDs | 1.3.6.1.4.1.2011.6.144.1.1.14.1.12 | Xdsl2RaMode | read-create | The mode of operation of a rate-adaptive xTU-C in the transmit direction. |
| XDS hwVOPSNRMarginConfProfRaModeUs | 1.3.6.1.4.1.2011.6.144.1.1.14.1.13 | Xdsl2RaMode | read-create | The mode of operation of a rate-adaptive xTU-R in the transmit direction. |
| G32 hwVOPSNRMarginConfProfRaUsNrmDs | 1.3.6.1.4.1.2011.6.144.1.1.14.1.14 | Gauge32 | read-create | The Downstream Up-Shift Noise Margin value, to be used when hwVOPSNRMarginConfProfRaModeDs is set to dynamicRa. If the downstream noise margin is above this value, and stays above it for more than the time specified by the hwVOPSNRMarginConfProfUsTimeDs, the xTU-R shall attempt to increase the downstream net data rate. The Downstream Up-Shift Noise Margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). Unit: 0.1 dB. |
| G32 hwVOPSNRMarginConfProfRaUsNrmUs | 1.3.6.1.4.1.2011.6.144.1.1.14.1.15 | Gauge32 | read-create | The Upstream Up-Shift Noise Margin value, to be used when hwVOPSNRMarginConfProfRaModeUs is set to dynamicRa. If the upstream noise margin is above this value, and stays above it for more than the time specified by the hwVOPSNRMarginConfProfUsTimeUs, the xTU-C shall attempt to increase the upstream net data rate. The Upstream Up-Shift Noise Margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). Unit: 0.1 dB. |
| G32 hwVOPSNRMarginConfProfRaDsNrmDs | 1.3.6.1.4.1.2011.6.144.1.1.14.1.16 | Gauge32 | read-create | The Downstream Down-Shift Noise Margin value, to be used when hwVOPSNRMarginConfProfRaModeDs is set to dynamicRa. If the downstream noise margin is below this value, and stays below it for more than the time specified by the hwVOPSNRMarginConfProfDsTimeDs, the xTU-R shall attempt to increase the downstream net data rate. The Downstream Down-Shift Noise Margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). Unit: 0.1 dB. |
| G32 hwVOPSNRMarginConfProfRaDsNrmUs | 1.3.6.1.4.1.2011.6.144.1.1.14.1.17 | Gauge32 | read-create | The Upstream Down-Shift Noise Margin value, to be used when hwVOPSNRMarginConfProfRaModeUs is set to dynamicRa. If the upstream noise margin is below this value, and stays below it for more than the time specified by the hwVOPSNRMarginConfProfDsTimeUs, the xTU-C shall attempt to increase the upstream net data rate. The Upstream Down-Shift Noise Margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). Unit: 0.1 dB. |
| G32 hwVOPSNRMarginConfProfUsTimeDs | 1.3.6.1.4.1.2011.6.144.1.1.14.1.18 | Gauge32 | read-create | The Downstream Up-Shift Time Interval, to be used when hwVOPSNRMarginConfProfRaModeDs is set to dynamicRa. The interval of time that the downstream noise margin should stay above the Downstream Up-Shift Noise Margin before the xTU-R shall attempt to increase the downstream net data rate. The time interval ranges from 0 to 16383 seconds. Unit: seconds. |
| G32 hwVOPSNRMarginConfProfUsTimeUs | 1.3.6.1.4.1.2011.6.144.1.1.14.1.19 | Gauge32 | read-create | The Upstream Up-Shift Time Interval, to be used when hwVOPSNRMarginConfProfRaModeUs is set to dynamicRa. The interval of time the upstream noise margin should stay above the Upstream Up-Shift Noise Margin before the xTU-C shall attempt to increase the upstream net data rate. The time interval ranges from 0 to 16383 seconds. Unit: seconds. |
| G32 hwVOPSNRMarginConfProfDsTimeDs | 1.3.6.1.4.1.2011.6.144.1.1.14.1.20 | Gauge32 | read-create | The Downstream Downshift Time Interval, to be used when hwVOPSNRMarginConfProfRaModeDs is set to dynamicRa. The interval of time the downstream noise margin should stay below the Downstream Down-Shift Noise Margin before the xTU-R shall attempt to decrease the downstream net data rate. The time interval ranges from 0 to 16383 seconds. Unit: seconds. |
| G32 hwVOPSNRMarginConfProfDsTimeUs | 1.3.6.1.4.1.2011.6.144.1.1.14.1.21 | Gauge32 | read-create | The Upstream Down-Shift Time Interval, to be used when hwVOPSNRMarginConfProfUsTimeUs is set to dynamicRa. The interval of time the upstream noise margin should stay below the Upstream Down-Shift Noise Margin before the xTU-C shall attempt to decrease the upstream net data rate. The time interval ranges from 0 to 16383 seconds. Unit: seconds. |
| HWV hwVOPINPDelayProfileIndexNext | 1.3.6.1.4.1.2011.6.144.1.1.15 | HWVOPProfileIndexOrZeroType | read-only | This object contains an appropriate value to be used for hwVOPINPDelayConfProfIndex when creating entries in the hwVOPINPDelayConfProfTableTable. The value '0' indicates that no unassigned entries are available. To obtain the value of hwVOPINPDelayConfProfIndex for a new entry in the table, the manager issues a management protocol retrieval operation. The agent will determine through its local policy when this index value will be made available for reuse. |
| hwVOPINPDelayConfProfTable | 1.3.6.1.4.1.2011.6.144.1.1.16 | not-accessible | The INP-Delay parameters for each pair of upstream and downstream channels will be in an INP-Delay Profile. To cover all possibilities there will be 4 indices in the vector for INP-Delay Profiles. If less than the maximum number of channels is to be used then the scalars corresponding to non-required channels MUST be set to a null value (0). Entries in this table MUST be maintained in a persistent manner. A default profile with an index of '1' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document. The index of this table is hwVOPINPDelayConfProfIndex. | |
| hwVOPINPDelayConfProfEntry | 1.3.6.1.4.1.2011.6.144.1.1.16.1 | not-accessible | The INP-Delay parameters for each pair of upstream and downstream channels will be in an INP-Delay Profile. To cover all possibilities there will be 4 indices in the vector for INP-Delay Profiles. If less than the maximum number of channels is to be used then the scalars corresponding to non-required channels MUST be set to a null value (0). Entries in this table MUST be maintained in a persistent manner. A default profile with an index of '1' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document. The index of this entry is hwVOPINPDelayConfProfIndex. | |
| U32 hwVOPINPDelayConfProfIndex | 1.3.6.1.4.1.2011.6.144.1.1.16.1.1 | Unsigned32 | not-accessible | The hwVOPINPDelayConfProfIndex identifies a row in the hwVOPINPDelayConfProfTable. |
| ROW hwVOPINPDelayConfProfRowStatus | 1.3.6.1.4.1.2011.6.144.1.1.16.1.2 | RowStatus | read-create | This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'notInService'), it MUST be first unreferenced from all associated DSL lines. A row in hwVOPINPDelayConfProfTable is said to be unreferenced when there is no instance of hwVOPActSetupInpDelayProfId1-4 in the hwVOPActSetupTable which refers to the row. |
| OCT hwVOPINPDelayConfProfDescription | 1.3.6.1.4.1.2011.6.144.1.1.16.1.3 | OCTET STRING | read-create | The hwVOPINPDelayConfProfDescription contains an optional human readable description for the profile. |
| XDS hwVOPINPDelayConfProfMinProtectionDs | 1.3.6.1.4.1.2011.6.144.1.1.16.1.4 | Xdsl2SymbolProtection | read-create | If retransmission is not used in downstream direction, this parameter specifies the minimum impulse noise protection for the downstream bearer channel if it is transported over DMT symbols with a subcarrier spacing of 4.3125 kHz. The impulse noise protection is expressed in DMT symbols with a subcarrier spacing of 4.3125 kHz and can take the values 1/2 and any integer from 0 to 16, inclusive. If the xTU does not support the configured INPMIN value,it shall use the nearest supported impulse noise protection greater than INPMIN. Unit: symbols. |
| XDS hwVOPINPDelayConfProfMinProtection8Ds | 1.3.6.1.4.1.2011.6.144.1.1.16.1.5 | Xdsl2SymbolProtection8 | read-create | If retransmission is not used in downstream direction, this parameter specifies the minimum impulse noise protection for the downstream bearer channel if it is transported over DMT symbols with a subcarrier spacing of 8.625 kHz. The impulse noise protection is expressed in DMT symbols with a subcarrier spacing of 8.625 kHz and can take any integer value from 0 to 16, inclusive. Unit: symbols. |
| G32 hwVOPINPDelayConfProfMaxDelayDs | 1.3.6.1.4.1.2011.6.144.1.1.16.1.6 | Gauge32 | read-create | If retransmission is not used in downstream direction, this parameter is the maximum one-way interleaving delay introduced by the PMS-TC on downstream direction. The xTUs shall choose the S (factor) and D(depth) values such that the actual one-way interleaving delay (Xdsl2ChStatusActDelay - VDSL2-LINE-MIB) is as close as possible to, but less than or equal to hwVOPINPDelayConfProfMaxDelayDs. The delay is coded in ms, with the value 0 indicating no delay bound is being imposed. The delay is coded in ms, with the special values 0, 1 and 255. - The value 0 indicates no delay bound is being imposed. - The value 1 indicates the Fast Latency Path shall be used in the G.992.1 operating mode and S and D shall be selected such that S <= 1 and D = 1 in ITU-T Recs G.992.2, G.992.3 and G.992.4 operating modes (G.997.1 special value S1). - The value 255 indicates a delay bound of 1 ms in ITU-T Recs G.993.2 (G.997.1 special value S2). Unit: milliseconds. |
| XDS hwVOPINPDelayConfProfMinProtectionUs | 1.3.6.1.4.1.2011.6.144.1.1.16.1.7 | Xdsl2SymbolProtection | read-create | If retransmission is not used in upstream direction, this parameter specifies the minimum impulse noise protection for the upstream bearer channel if it is transported over DMT symbols with a subcarrier spacing of 4.3125 kHz. The impulse noise protection is expressed in DMT symbols with a subcarrier spacing of 4.3125 kHz and can take the values 1/2 and any integer from 0 to 16, inclusive. If the xTU does not support the configured INPMIN value, it shall use the nearest supported impulse noise protection greater than INPMIN. Unit: symbols. |
| XDS hwVOPINPDelayConfProfMinProtection8Us | 1.3.6.1.4.1.2011.6.144.1.1.16.1.8 | Xdsl2SymbolProtection8 | read-create | If retransmission is not used in upstream direction, this parameter specifies the minimum impulse noise protection for the upstream bearer channel if it is transported over DMT symbols with a subcarrier spacing of 8.625 kHz. The impulse noise protection is expressed in DMT symbols with a subcarrier spacing of 8.625 kHz and can take any integer value from 0 to 16, inclusive. Unit: symbols. |
| G32 hwVOPINPDelayConfProfMaxDelayUs | 1.3.6.1.4.1.2011.6.144.1.1.16.1.9 | Gauge32 | read-create | If retransmission is not used in upstream direction, this parameter is the maximum one-way interleaving delay introduced by the PMS-TC on upstream direction. The xTUs shall choose the S (factor) and D(depth) values such that the actual one-way interleaving delay (Xdsl2ChStatusActDelay - VDSL2-LINE-MIB) is as close as possible to, but less than or equal to hwVOPINPDelayConfProfMaxDelayUs. The delay is coded in ms, with the value 0 indicating no delay bound is being imposed. The delay is coded in ms, with the special values 0, 1 and 255. - The value 0 indicates no delay bound is being imposed. - The value 1 indicates the Fast Latency Path shall be used in the G.992.1 operating mode and S and D shall be selected such that S <= 1 and D = 1 in ITU-T Recs G.992.2, G.992.3 and G.992.4 operating modes (G.997.1 special value S1). - The value 255 indicates a delay bound of 1 ms in ITU-T Recs G.993.2 (G.997.1 special value S2). Unit: milliseconds. |
| G32 hwVOPINPDelayConfProfMaxDelayVar | 1.3.6.1.4.1.2011.6.144.1.1.16.1.10 | Gauge32 | read-create | This optional VDSL2 specific parameter specifies the maximum value for the delay variation allowed in an OLR procedure. It is ranges from 1 to 254 units of 0.1 milliseconds (i.e., 0.1 to 25.4 milliseconds) with the special value 255 which indicates that no delay variation bound is imposed. Unit: 0.1 milliseconds. |
| XDS hwVOPINPDelayConfProfInitPolicy | 1.3.6.1.4.1.2011.6.144.1.1.16.1.11 | Xdsl2ChInitPolicy | read-create | If retransmission is not used in a given transmit direction, this parameter indicates which policy shall be applied to determine the transceiver configuration parameters at initialization. The valid values for CIPOLICY are 0,1 and 2. Those policies are defined in the respective Recommendations. |
| G32 hwVOPINPDelayConfProfMaxDelayRtxDs | 1.3.6.1.4.1.2011.6.144.1.1.16.1.12 | Gauge32 | read-create | If retransmission is used in downstream direction, this parameter specifies the maximum for the instantaneous delay due to the effect of retransmission only (see G.998.4 for detailed specification). The delay ranges from 1 to 63 ms by steps of 1 ms. Unit: milliseconds |
| G32 hwVOPINPDelayConfProfMaxDelayRtxUs | 1.3.6.1.4.1.2011.6.144.1.1.16.1.13 | Gauge32 | read-create | If retransmission is used in upstream direction, this parameter specifies the maximum for the instantaneous delay due to the effect of retransmission only (see G.998.4 for detailed specification). The delay ranges from 1 to 63 ms by steps of 1 ms. Unit: milliseconds |
| G32 hwVOPINPDelayConfProfMinDelayRtxDs | 1.3.6.1.4.1.2011.6.144.1.1.16.1.14 | Gauge32 | read-create | If retransmission is used in downstream direction, this parameter specifies the minimum for the instantaneous delay due to the effect of retransmission only (see G.998.4 for detailed specification). The delay ranges from 0 to 63 ms by steps of 1 ms. Unit: milliseconds |
| G32 hwVOPINPDelayConfProfMinDelayRtxUs | 1.3.6.1.4.1.2011.6.144.1.1.16.1.15 | Gauge32 | read-create | If retransmission is used in upstream direction, this parameter specifies the minimum for the instantaneous delay due to the effect of retransmission only (see G.998.4 for detailed specification). The delay ranges from 0 to 63 ms by steps of 1 ms. Unit: milliseconds |
| G32 hwVOPINPDelayConfProfMinInpShineRtxDs | 1.3.6.1.4.1.2011.6.144.1.1.16.1.16 | Gauge32 | read-create | If retransmission is used in downstream direction, this parameter specifies the minimum impulse noise protection against SHINE for the bearer channel if it is transported over DMT symbols with a subcarrier spacing of 4.3125 kHz. The impulse noise protection is expressed in DMT symbols with a subcarrier spacing of 4.3125 kHz and can take any integer value from 0 to 63, inclusive. Unit: symbols |
| G32 hwVOPINPDelayConfProfMinInpShineRtxUs | 1.3.6.1.4.1.2011.6.144.1.1.16.1.17 | Gauge32 | read-create | If retransmission is used in upstream direction, this parameter specifies the minimum impulse noise protection against SHINE for the bearer channel if it is transported over DMT symbols with a subcarrier spacing of 4.3125 kHz. The impulse noise protection is expressed in DMT symbols with a subcarrier spacing of 4.3125 kHz and can take any integer value from 0 to 63, inclusive. Unit: symbols |
| G32 hwVOPINPDelayConfProfMinInp8ShineRtxDs | 1.3.6.1.4.1.2011.6.144.1.1.16.1.18 | Gauge32 | read-create | If retransmission is used in downstream direction, this parameter specifies the minimum impulse noise protection against SHINE for the bearer channel if it is transported over DMT symbols with a subcarrier spacing of 8.625 kHz. The impulse noise protection is expressed in DMT symbols with a subcarrier spacing of 8.625 kHz and can take any integer value from 0 to 127, inclusive. Unit: symbols |
| G32 hwVOPINPDelayConfProfMinInp8ShineRtxUs | 1.3.6.1.4.1.2011.6.144.1.1.16.1.19 | Gauge32 | read-create | If retransmission is used in upstream direction, this parameter specifies the minimum impulse noise protection against SHINE for the bearer channel if it is transported over DMT symbols with a subcarrier spacing of 8.625 kHz. The impulse noise protection is expressed in DMT symbols with a subcarrier spacing of 8.625 kHz and can take any integer value from 0 to 127, inclusive. Unit: symbols |
| G32 hwVOPINPDelayConfProfShineRatioRtxDs | 1.3.6.1.4.1.2011.6.144.1.1.16.1.20 | Gauge32 | read-create | If retransmission is used in downstream direction, this parameter specifies the SHINE ratio (detailed definition see G.998.4). The values range from 0 to 0.100 in increments of 0.001. |
| G32 hwVOPINPDelayConfProfShineRatioRtxUs | 1.3.6.1.4.1.2011.6.144.1.1.16.1.21 | Gauge32 | read-create | If retransmission is used in upstream direction, this parameter specifies the SHINE ratio (detailed definition see G.998.4). The values range from 0 to 0.100 in increments of 0.001. |
| G32 hwVOPINPDelayConfProfMinInpReinRtxDs | 1.3.6.1.4.1.2011.6.144.1.1.16.1.22 | Gauge32 | read-create | If retransmission is used in downstream direction, this parameter specifies the minimum impulse noise protection against REIN for the bearer channel if it is transported over DMT symbols with a subcarrier spacing of 4.3125 kHz. The impulse noise protection is expressed in DMT symbols with a subcarrier spacing of 4.3125 kHz and can take any integer value from 0 to 7, inclusive. |
| G32 hwVOPINPDelayConfProfMinInpReinRtxUs | 1.3.6.1.4.1.2011.6.144.1.1.16.1.23 | Gauge32 | read-create | If retransmission is used in upstream direction, this parameter specifies the minimum impulse noise protection against REIN for the bearer channel if it is transported over DMT symbols with a subcarrier spacing of 4.3125 kHz. The impulse noise protection is expressed in DMT symbols with a subcarrier spacing of 4.3125 kHz and can take any integer value from 0 to 7, inclusive. |
| G32 hwVOPINPDelayConfProfMinInp8ReinRtxDs | 1.3.6.1.4.1.2011.6.144.1.1.16.1.24 | Gauge32 | read-create | If retransmission is used in downstream direction, this parameter specifies the minimum impulse noise protection against REIN for the bearer channel if it is transported over DMT symbols with a subcarrier spacing of 8.625 kHz. The impulse noise protection is expressed in DMT symbols with a subcarrier spacing of 8.625 kHz and can take any integer value from 0 to 13, inclusive. |
| G32 hwVOPINPDelayConfProfMinInp8ReinRtxUs | 1.3.6.1.4.1.2011.6.144.1.1.16.1.25 | Gauge32 | read-create | If retransmission is used in upstream direction, this parameter specifies the minimum impulse noise protection against REIN for the bearer channel if it is transported over DMT symbols with a subcarrier spacing of 8.625 kHz. The impulse noise protection is expressed in DMT symbols with a subcarrier spacing of 8.625 kHz and can take any integer value from 0 to 13, inclusive. |
| INT hwVOPINPDelayConfProfIatReinRtxDs | 1.3.6.1.4.1.2011.6.144.1.1.16.1.26 | INTEGER | read-create | If retransmission is used in downstream direction, this parameter specifies the inter-arrival time that shall be assumed for REIN protection. Options: 1. frequency100Hz(0) - an inter-arrival time derived from a REIN at 100 Hz 2. frequency120Hz(1) - an inter-arrival time derived from a REIN at 120 Hz |
| INT hwVOPINPDelayConfProfIatReinRtxUs | 1.3.6.1.4.1.2011.6.144.1.1.16.1.27 | INTEGER | read-create | If retransmission is used in upstream direction, this parameter specifies the inter-arrival time that shall be assumed for REIN protection. Options: 1. frequency100Hz(0) - an inter-arrival time derived from a REIN at 100 Hz 2. frequency120Hz(1) - an inter-arrival time derived from a REIN at 120 Hz |
| HWV hwVOPVirtualNoiseProfileIndexNext | 1.3.6.1.4.1.2011.6.144.1.1.17 | HWVOPProfileIndexOrZeroType | read-only | This object contains an appropriate value to be used for hwVOPVirtualNoiseConfProfIndex when creating entries in the hwVOPVirtualNoiseConfProfTable. The value '0' indicates that no unassigned entries are available. To obtain the value of hwVOPVirtualNoiseConfProfIndex for a new entry in the table, the manager issues a management protocol retrieval operation. The agent will determine through its local policy when this index value will be made available for reuse. |
| hwVOPVirtualNoiseConfProfTable | 1.3.6.1.4.1.2011.6.144.1.1.18 | not-accessible | The Virtual Noise Profile MUST contain the virtual noise PSDs. A Virtual Noise PSD is not used if the corresponding SNRMODE parameters (hwVOPSNRMarginConfProfMaxSnrmDs, hwVOPSNRMarginConfProfRaModeUs) are set to 0. The SNRMODE parameters for upstream and downstream are in the hwVOPSNRMarginConfProfTable. Entries in this table MUST be maintained in a persistent manner. A default profile with an index of '1' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document. The index of this table is hwVOPVirtualNoiseConfProfIndex. | |
| hwVOPVirtualNoiseConfProfEntry | 1.3.6.1.4.1.2011.6.144.1.1.18.1 | not-accessible | The Virtual Noise Profile MUST contain the virtual noise PSDs. A Virtual Noise PSD is not used if the corresponding SNRMODE parameters (hwVOPSNRMarginConfProfMaxSnrmDs, hwVOPSNRMarginConfProfRaModeUs) are set to 0. The SNRMODE parameters for upstream and downstream are in the hwVOPSNRMarginConfProfTable. Entries in this table MUST be maintained in a persistent manner. A default profile with an index of '1' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document. The index of this entry is hwVOPVirtualNoiseConfProfIndex. | |
| U32 hwVOPVirtualNoiseConfProfIndex | 1.3.6.1.4.1.2011.6.144.1.1.18.1.1 | Unsigned32 | not-accessible | The hwVOPVirtualNoiseConfProfIndex identifies a row in the hwVOPVirtualNoiseConfProfTable. |
| ROW hwVOPVirtualNoiseConfProfRowStatus | 1.3.6.1.4.1.2011.6.144.1.1.18.1.2 | RowStatus | read-create | This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'notInService'), it MUST be first unreferenced from all associated DSL lines. A row in hwVOPVirtualNoiseConfProfTable is said to be unreferenced when there is no instance of hwVOPActSetupVNoiseProfId in the hwVOPActSetupTable which refers to the row. |
| OCT hwVOPVirtualNoiseConfProfDescription | 1.3.6.1.4.1.2011.6.144.1.1.18.1.3 | OCTET STRING | read-create | The hwVOPVirtualNoiseConfProfDescription contains an optional human readable description for the profile. |
| XDS hwVOPVirtualNoiseConfProfTxRefVnDs | 1.3.6.1.4.1.2011.6.144.1.1.18.1.4 | Xdsl2LineTxRefVnDs | read-create | This configuration parameter defines the downstream transmitter referred virtual noise. The TXREFVNds shall be specified through a set of breakpoints. Each breakpoint shall consist of a subcarrier index t, with a subcarrier spacing of 4.3125 kHz, and a noise PSD level (expressed in dBm/Hz) at that subcarrier. The set of breakpoints can then be represented as: [(t1,PSD1), (t2, PSD2), ... , (tN, PSDN)]. 32 groups can be configured at most, and 3 bytes for each group. The first two bytes represent tone index, the 3th byte represents the configured PSD value. The relation between configured PSD value and real PSD value is: REAL PSD = (CONFIGURED PSD + 80) * (-0.5dBm/Hz). |
| XDS hwVOPVirtualNoiseConfProfTxRefVnUs | 1.3.6.1.4.1.2011.6.144.1.1.18.1.5 | Xdsl2LineTxRefVnUs | read-create | This configuration parameter defines the upstream transmitter referred virtual noise. The TXREFVNus shall be specified through a set of breakpoints. Each breakpoint shall consist of a subcarrier index t, with a subcarrier spacing of 4.3125 kHz, and a noise PSD level (expressed in dBm/Hz) at that subcarrier. The set of breakpoints can then be represented as: [(t1, PSD1), (t2, PSD2), ... , (tN, PSDN)]. 16 groups can be configured at most, and 3 bytes for each group. The first two bytes represent tone index, the 3th byte represents the configured PSD value. The relation between configured PSD value and real PSD value is: REAL PSD = (CONFIGURED PSD + 80) * (-0.5dBm/Hz). |
| HWV hwVOPINMProfileIndexNext | 1.3.6.1.4.1.2011.6.144.1.1.19 | HWVOPProfileIndexOrZeroType | read-only | This object contains an appropriate value to be used for hwVOPINMConfProfIndex when creating entries in the hwVOPINMConfProfTable. The value '0' indicates that no unassigned entries are available. To obtain the value of hwVOPINMConfProfIndex for a new entry in the table, the manager issues a management protocol retrieval operation. The agent will determine through its local policy when this index value will be made available for reuse. |
| hwVOPINMConfProfTable | 1.3.6.1.4.1.2011.6.144.1.1.20 | not-accessible | Impulse Noise Monitoring(INM) is not required for modem operation but is a capability for the measurement of Impulse Noise. The INM Profile includes the option to control an INM function on the receive direction in the xTU. A downstream Impulse Noise Monitor applies to the xTU-R; an upstream Impulse Noise Monitor applies to the xTU-C. If INM is not implemented, the relevant profile pointer within the xDSL Line Configuration Vector instance MUST be set to a null value(0). A default profile with an index of '1' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document. The index of this table is hwVOPINMConfProfIndex. | |
| hwVOPINMConfProfEntry | 1.3.6.1.4.1.2011.6.144.1.1.20.1 | not-accessible | Impulse Noise Monitoring(INM) is not required for modem operation but is a capability for the measurement of Impulse Noise. The INM Profile includes the option to control an INM function on the receive direction in the xTU. A downstream Impulse Noise Monitor applies to the xTU-R; an upstream Impulse Noise Monitor applies to the xTU-C. If INM is not implemented, the relevant profile pointer within the xDSL Line Configuration Vector instance MUST be set to a null value(0). A default profile with an index of '1' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document. The index of this entry is hwVOPINMConfProfIndex. | |
| U32 hwVOPINMConfProfIndex | 1.3.6.1.4.1.2011.6.144.1.1.20.1.1 | Unsigned32 | not-accessible | The hwVOPINMConfProfIndex identifies a row in the hwVOPINMConfProfTable. |
| ROW hwVOPINMConfProfRowStatus | 1.3.6.1.4.1.2011.6.144.1.1.20.1.2 | RowStatus | read-create | This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'notInService'), it MUST be first unreferenced from all associated DSL lines. A row in hwVOPINMConfProfTable is said to be unreferenced when there is no instance of hwVOPActSetupVNoiseProfId in the hwVOPActSetupTable which refers to the row. |
| OCT hwVOPINMConfProfDescription | 1.3.6.1.4.1.2011.6.144.1.1.20.1.3 | OCTET STRING | read-create | The hwVOPINMConfProfDescription contains an optional human readable description for the profile. |
| U32 hwVOPINMConfProfInmIatoDs | 1.3.6.1.4.1.2011.6.144.1.1.20.1.4 | Unsigned32 | read-create | The parameter of downstream impulse noise monitoring inter arrival time offset. This is the Inter Arrival Time Offset that the xTU receiver shall use to determine in which bin of the Inter Arrival Time histogram the IAT is reported. The valid values for INMIATO ranges from 3 to 511 DMT symbols in steps of 1 DMT symbol. |
| U32 hwVOPINMConfProfInmIatsDs | 1.3.6.1.4.1.2011.6.144.1.1.20.1.5 | Unsigned32 | read-create | The parameter of downstream impulse noise monitoring inter arrival time step. This is the Inter Arrival Time Step that the xTU receiver shall use to determine in which bin of the Inter Arrival Time histogram the IAT is reported. The valid values for INMIATS ranges from 0 to 7 in steps of 1. |
| U32 hwVOPINMConfProfInmCcDs | 1.3.6.1.4.1.2011.6.144.1.1.20.1.6 | Unsigned32 | read-create | The parameter of Downstream impulse noise monitoring cluster continuation value. This is the Cluster Continuation value that the xTU receiver shall use in the cluster indication process described in the relevant ITU-T Recommendation. The valid values for INMCC range from 0 to 64 DMT symbols in steps of 1 DMT symbol. |
| U32 hwVOPINMConfProfInmInpeqModeDs | 1.3.6.1.4.1.2011.6.144.1.1.20.1.7 | Unsigned32 | read-create | The parameter of Downstream impulse noise monitoring equivalent impulse noise protect mode. This is the INM Equivalent INP Mode that the xTU receiver shall use in the computation of the Equivalent INP, as defined in the relevant ITU-T Recommendation. The valid values for INM_INPEQ_MODE are 0, 1, 2, 3, and 4. |
| U32 hwVOPINMConfProfInmIatoUs | 1.3.6.1.4.1.2011.6.144.1.1.20.1.8 | Unsigned32 | read-create | The parameter of upstream impulse noise monitoring inter arrival time offset. This is the Inter Arrival Time Offset that the xTU receiver shall use to determine in which bin of the Inter Arrival Time histogram the IAT is reported. The valid values for INMIATO ranges from 3 to 511 DMT symbols in steps of 1 DMT symbol. |
| U32 hwVOPINMConfProfInmIatsUs | 1.3.6.1.4.1.2011.6.144.1.1.20.1.9 | Unsigned32 | read-create | The parameter of upstream impulse noise monitoring inter arrival time step. This is the Inter Arrival Time Step that the xTU receiver shall use to determine in which bin of the Inter Arrival Time histogram the IAT is reported. The valid values for INMIATS ranges from 0 to 7 in steps of 1. |
| U32 hwVOPINMConfProfInmCcUs | 1.3.6.1.4.1.2011.6.144.1.1.20.1.10 | Unsigned32 | read-create | The parameter of upstream impulse noise monitoring cluster continuation value. This is the Cluster Continuation value that the xTU receiver shall use in the cluster indication process described in the relevant ITU-T Recommendation. The valid values for INMCC range from 0 to 64 DMT symbols in steps of 1 DMT symbol. |
| U32 hwVOPINMConfProfInmInpeqModeUs | 1.3.6.1.4.1.2011.6.144.1.1.20.1.11 | Unsigned32 | read-create | The parameter of upstream impulse noise monitoring equivalent impulse noise protect mode. This is the INM Equivalent INP Mode that the xTU receiver shall use in the computation of the Equivalent INP, as defined in the relevant ITU-T Recommendation. The valid values for INM_INPEQ_MODE are 0, 1, 2, 3, and 4. |
| hwVOPVectors | 1.3.6.1.4.1.2011.6.144.1.2 | |||
| hwVOPGlobal | 1.3.6.1.4.1.2011.6.144.1.2.1 | |||
| HWV hwVOPGlobalAttachmentMethodCapabilties | 1.3.6.1.4.1.2011.6.144.1.2.1.1 | HWVOPAttachmentMethods | read-only | This object reflects the VoP attachment-method(s) this Network Element supports. Two attachment methods, 'direct' and 'indirect' are available and each Network Element MAY be able to support both attachment-methods (but not at the same time). The capability to support a specific attachment-method is indicated by the respective bit-position set to '1'. Particularly, a network element that supports both methods SHOULD indicate that by both bit-positions set to '1'. |
| HWV hwVOPGlobalAttachmentMethodConfigured | 1.3.6.1.4.1.2011.6.144.1.2.1.2 | HWVOPAttachmentMethods | read-write | This object configures the VoP attachment-method to be used by this Network Element. Two attachment methods, 'direct' and 'indirect' are available and only one method can be selected at any time. To select a specific attachment-method the management system SHOULD set the respective bit-position to '1'. Changing the requested attachment-method may implies a system reboot. The value of this object MUST be maintained in a persistent manner. In case the selected attachment-method is not supported by the network element or if the management system tries to configure both methods simultaneously the SNMP SET operation SHOULD be rejected by the network element. Default value is 1(direct). |
| HWV hwVOPGlobalAttachmentMethodCurrent | 1.3.6.1.4.1.2011.6.144.1.2.1.3 | HWVOPAttachmentMethods | read-only | This object reflects the VoP attachment-method currently used by this Network Element. Two attachment methods, 'direct' and 'indirect' are available and only one method can be used at any time. The specific attachment-method used is indicated by the respective bit-position set to '1'. Changing the requested attachment-method may implies a system reboot. |
| hwVOPSetup | 1.3.6.1.4.1.2011.6.144.1.2.2 | |||
| HWV hwVOPSetupProfileIndexNext | 1.3.6.1.4.1.2011.6.144.1.2.2.1 | HWVOPSetupIndexOrZeroType | read-only | This object is required only in case the 'indirect' attachment-method of VoP to xDSL lines is implemented, in which case entries/rows in hwVOPSetupTable are dynamically created and deleted by the management system. When implemented, the object reports an appropriate value to be used for hwVOPSetupIndex when creating entries in the hwVOPSetupTable. The value '0' indicates that no unassigned entries are available. To obtain the value of hwVOPSetupIndex for a new entry in the table, the manager issues a management protocol retrieval operation. The agent will determine through its local policy when this index value will be made available for reuse. |
| hwVOPSetupTable | 1.3.6.1.4.1.2011.6.144.1.2.2.2 | not-accessible | This table contains a collection of profile indices that construct a Vector Of Profiles (VoP). This table is used in both 'direct' and 'indirect' attachment-methods of VoP to xDSL lines. In case the implementation uses 'direct' attachment-method of configuration VoP to xDSL lines then: 1) a row in this table is automatically created and deleted by the SNMP agent together with creating a row in the xdsl2LineTable (VDSL2-LINE-MIB) for any xDSL line. 2) The row index is same as the index of the respective row in xdsl2LineTable. Thus, this table can be considered as extending the xdsl2LineTable. 3) The row status object (hwVOPSetupRowStatus) and profile description(hwVOPSetupDescription) are unused. 4) The management system may modify the contents of each row in the table and, by that, modify the required configuration VoP for the related xDSL line. 5) Note that the hwVOPActSetupTable reflects the configuration VoP currently used by each xDSL line. Its importance is demonstrated during the time between modifying the configuration VoP of any xDSL line and practically applying it to the xDSL line. In case the implementation uses 'direct' attachment-method of VoP to xDSL lines then a row in the table is automatically created by the SNMP agent when a respective row is created in the xdsl2LineTable. The row objects will be set to default values. In case the implementation uses 'indirect' attachment-method of VoP to xDSL lines then a default profile with an index number 1 will always exist and its objects will be set to default values. The index of this table is hwVOPSetupIndex. | |
| hwVOPSetupEntry | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1 | not-accessible | This table contains a collection of profile indices that construct a Vector Of Profiles (VoP). This table is used in both 'direct' and 'indirect' attachment-methods of VoP to xDSL lines. In case the implementation uses 'direct' attachment-method of configuration VoP to xDSL lines then: 1) a row in this table is automatically created and deleted by the SNMP agent together with creating a row in the xdsl2LineTable (VDSL2-LINE-MIB) for any xDSL line. 2) The row index is same as the index of the respective row in xdsl2LineTable. Thus, this table can be considered as extending the xdsl2LineTable. 3) The row status object (hwVOPSetupRowStatus) and profile description(hwVOPSetupDescription) are unused. 4) The management system may modify the contents of each row in the table and, by that, modify the required configuration VoP for the related xDSL line. 5) Note that the hwVOPActSetupTable reflects the configuration VoP currently used by each xDSL line. Its importance is demonstrated during the time between modifying the configuration VoP of any xDSL line and practically applying it to the xDSL line. In case the implementation uses 'direct' attachment-method of VoP to xDSL lines then a row in the table is automatically created by the SNMP agent when a respective row is created in the xdsl2LineTable. The row objects will be set to default values. In case the implementation uses 'indirect' attachment-method of VoP to xDSL lines then a default profile with an index number 1 will always exist and its objects will be set to default values. The index of this entry is hwVOPSetupIndex. | |
| U32 hwVOPSetupIndex | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.1 | Unsigned32 | not-accessible | The hwVOPSetupIndex identifies a row in the hwVOPSetupTable. A row in this table may be indexed either by an ifIndex pattern, in case the 'direct' attachment-method of VoP to xDSL rows is implemented, or by a unique ordered number, in case the 'indirect' attachment-method of VoP to xDSL rows is implemented. |
| ROW hwVOPSetupRowStatus | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.2 | RowStatus | read-create | This object is used, in case the 'indirect' attachment-method of VoP to xDSL lines is implemented, to create a new row, to modify a row, or delete an existing row in this table. In case the 'direct' attachment-method of VoP to xDSL lines is implemented then rows in this table are automatically created and deleted by the embedded system and this object is not implemented/used. When the object is being used, as described above, rows in this table are dynamically created, modified and deleted by the management system. When the object is being used then before a row in this table can be deleted or taken out of service (by setting this object to 'destroy' or 'notInService'), it MUST be first un-referenced from all associated xDSL lines. A row in voSetupTable is said to be not referenced when there is no instance of xdsl2LineTable (VDSL2-LINE-MIB) which refers to the row. |
| OCT hwVOPSetupDescription | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.3 | OCTET STRING | read-create | The hwVOPSetupDescription contains an optional human readable description for the profile. This object is more likely to be used in case the 'indirect' attachment-method of VoP to xDSL lines is implemented. However, if implemented in 'direct' attachment-method of VoP to xDSL lines then this object has read-write accessibility. |
| U32 hwVOPSetupUsDataRateProfId1 | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.4 | Unsigned32 | read-create | This object identifies a row in hwVOPDataRateConfProfTable used for configuring the upstream transmission direction of channel #1. This object has read-write accessibility if 'direct' attachment-method of VoP to xDSL lines is implemented. |
| U32 hwVOPSetupUsRaRatio1 | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.5 | Unsigned32 | read-create | Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #1 when performing rate adaptation on upstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - hwVOPSetupUsRaRatio1 is the ratio of excess data rate to be assigned to all other bearer channels on upstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%. This object has read-write accessibility if 'direct' attachment-method of VoP to xDSL lines is implemented. |
| U32 hwVOPSetupDsDataRateProfId1 | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.6 | Unsigned32 | read-create | This object identifies a row in hwVOPDataRateConfProfTable used for configuring the downstream transmission direction of channel #1. This object has read-write accessibility if 'direct' attachment-method of VoP to xDSL lines is implemented. |
| U32 hwVOPSetupDsRaRatio1 | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.7 | Unsigned32 | read-create | Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #1 when performing rate adaptation on downstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - hwVOPSetupDsRaRatio1 is the ratio of excess data rate to be assigned to all other bearer channels on downstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%. This object has read-write accessibility if 'direct' attachment-method of VoP to xDSL lines is implemented. |
| U32 hwVOPSetupInpDelayProfId1 | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.8 | Unsigned32 | read-create | This object identifies a row in hwVOPINPDelayConfProfTable used for configuring the INP-Delay parameters of channel #1. This object has read-write accessibility if 'direct' attachment-method of VoP to xDSL lines is implemented. |
| U32 hwVOPSetupUsDataRateProfId2 | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.9 | Unsigned32 | read-create | This object identifies a row in hwVOPDataRateConfProfTable used for configuring the upstream transmission direction of channel #2. If channel #2 is not being used this object should be set to 0. This object has read-write accessibility if 'direct' attachment-method of VoP to xDSL lines is implemented. |
| U32 hwVOPSetupUsRaRatio2 | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.10 | Unsigned32 | read-create | Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #2 when performing rate adaptation on upstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - hwVOPSetupUsRaRatio2 is the ratio of excess data rate to be assigned to all other bearer channels on upstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%. This object has read-write accessibility if 'direct' attachment-method of VoP to xDSL lines is implemented. |
| U32 hwVOPSetupDsDataRateProfId2 | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.11 | Unsigned32 | read-create | This object identifies a row in hwVOPDataRateConfProfTable used for configuring the downstream transmission direction of channel #2. If channel #2 is not being used this object should be set to 0. This object has read-write accessibility if 'direct' attachment-method of VoP to xDSL lines is implemented. |
| U32 hwVOPSetupDsRaRatio2 | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.12 | Unsigned32 | read-create | Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #2 when performing rate adaptation on downstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - hwVOPSetupDsRaRatio2 is the ratio of excess data rate to be assigned to all other bearer channels on downstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%. This object has read-write accessibility if 'direct' attachment-method of VoP to xDSL lines is implemented. |
| U32 hwVOPSetupInpDelayProfId2 | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.13 | Unsigned32 | read-create | This object identifies a row in hwVOPINPDelayConfProfTable used for configuring the INP-Delay parameters of channel #2. If channel #2 is not being used this object should be set to 0. This object has read-write accessibility if 'direct' attachment-method of VoP to xDSL lines is implemented. |
| U32 hwVOPSetupUsDataRateProfId3 | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.14 | Unsigned32 | read-create | This object identifies a row in hwVOPDataRateConfProfTable used for configuring the upstream transmission direction of channel #3. If channel #3 is not being used this object should be set to 0. This object has read-write accessibility if 'direct' attachment-method of VoP to xDSL lines is implemented. |
| U32 hwVOPSetupUsRaRatio3 | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.15 | Unsigned32 | read-create | Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #3 when performing rate adaptation on upstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - hwVOPSetupUsRaRatio3 is the ratio of excess data rate to be assigned to all other bearer channels on upstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%. This object has read-write accessibility if 'direct' attachment-method of VoP to xDSL lines is implemented. |
| U32 hwVOPSetupDsDataRateProfId3 | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.16 | Unsigned32 | read-create | This object identifies a row in hwVOPDataRateConfProfTable used for configuring the downstream transmission direction of channel #3. If channel #3 is not being used this object should be set to 0. This object has read-write accessibility if 'direct' attachment-method of VoP to xDSL lines is implemented. |
| U32 hwVOPSetupDsRaRatio3 | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.17 | Unsigned32 | read-create | Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #3 when performing rate adaptation on downstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - hwVOPSetupDsRaRatio3 is the ratio of excess data rate to be assigned to all other bearer channels on downstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%. This object has read-write accessibility if 'direct' attachment-method of VoP to xDSL lines is implemented. |
| U32 hwVOPSetupInpDelayProfId3 | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.18 | Unsigned32 | read-create | This object identifies a row in hwVOPINPDelayConfProfTable used for configuring the INP-Delay parameters of channel #3. If channel #3 is not being used this object should be set to 0. This object has read-write accessibility if 'direct' attachment-method of VoP to xDSL lines is implemented. |
| U32 hwVOPSetupUsDataRateProfId4 | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.19 | Unsigned32 | read-create | This object identifies a row in hwVOPDataRateConfProfTable used for configuring the upstream transmission direction of channel #4. If channel #4 is not being used this object should be set to 0. This object has read-write accessibility if 'direct' attachment-method of VoP to xDSL lines is implemented. |
| U32 hwVOPSetupUsRaRatio4 | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.20 | Unsigned32 | read-create | Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #4 when performing rate adaptation on upstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - hwVOPSetupUsRaRatio4 is the ratio of excess data rate to be assigned to all other bearer channels on upstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%. This object has read-write accessibility if 'direct' attachment-method of VoP to xDSL lines is implemented. |
| U32 hwVOPSetupDsDataRateProfId4 | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.21 | Unsigned32 | read-create | This object identifies a row in hwVOPDataRateConfProfTable used for configuring the downstream transmission direction of channel #4. If channel #4 is not being used this object should be set to 0. This object has read-write accessibility if 'direct' attachment-method of VoP to xDSL lines is implemented. |
| U32 hwVOPSetupDsRaRatio4 | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.22 | Unsigned32 | read-create | Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #4 when performing rate adaptation on downstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - hwVOPSetupDsRaRatio4 is the ratio of excess data rate to be assigned to all other bearer channels on downstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%. This object has read-write accessibility if 'direct' attachment-method of VoP to xDSL lines is implemented. |
| U32 hwVOPSetupInpDelayProfId4 | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.23 | Unsigned32 | read-create | This object identifies a row in hwVOPINPDelayConfProfTable used for configuring the INP-Delay parameters of channel #4. If channel #4 is not being used this object should be set to 0. This object has read-write accessibility if 'direct' attachment-method of VoP to xDSL lines is implemented. |
| U32 hwVOPSetupLSpectrumProfId | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.24 | Unsigned32 | read-create | This object identifies a row in hwVOPLineSpectrumConfProfTable used for configuring the spectrum parameters of the respective xDSL line. This object has read-write accessibility if 'direct' attachment-method of VoP to xDSL lines is implemented. |
| U32 hwVOPSetupUpboProfId | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.25 | Unsigned32 | read-create | This object identifies a row in hwVOPUPBOConfProfTable used for configuring the upstream power back-off related parameters of the respective xDSL line. If this leaf is not support this object should be set to 0. This object has read-write accessibility if 'direct' attachment-method of VoP to xDSL lines is implemented. |
| U32 hwVOPSetupDpboProfId | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.26 | Unsigned32 | read-create | This object identifies a row in hwVOPDPBOConfProfTable used for configuring the downstream power back-off related parameters of the respective xDSL line. This object has read-write accessibility if 'direct' attachment-method of VoP to xDSL lines is implemented. |
| U32 hwVOPSetupRfiProfId | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.27 | Unsigned32 | read-create | This object identifies a row in hwVOPRFIConfProfTable used for configuring the RFI notches related parameters of the respective xDSL line. This object has read-write accessibility if 'direct' attachment-method of VoP to xDSL lines is implemented. |
| U32 hwVOPSetupNoiseMarginProfId | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.28 | Unsigned32 | read-create | This object identifies a row in hwVOPSNRMarginConfProfTable used for configuring the noise margin related parameters of the respective xDSL line. This object has read-write accessibility if 'direct' attachment-method of VoP to xDSL lines is implemented. |
| U32 hwVOPSetupVNoiseProfId | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.29 | Unsigned32 | read-create | This object identifies a row in hwVOPVirtualNoiseConfProfTable used for configuring the virtual noise related parameters of the respective xDSL line. This object has read-write accessibility if 'direct' attachment-method of VoP to xDSL lines is implemented. |
| U32 hwVOPSetupInmProfId | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.30 | Unsigned32 | read-create | This object identifies a row in hwVOPINMConfProfTable used for configuring the impulse noise monitoring parameters of the respective xDSL line. This object has read-write accessibility if 'direct' attachment-method of VoP to xDSL lines is implemented. |
| OCT hwVOPSetupUsDataRateProf1Description | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.31 | OCTET STRING | read-create | This object identifies a row in hwVOPDataRateConfProfTable used for configuring the upstream transmission direction of channel #1. This object has read-write accessibility if 'direct' attachment-method of VoP to xDSL lines is implemented. |
| OCT hwVOPSetupDsDataRateProf1Description | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.32 | OCTET STRING | read-create | This object identifies a row in hwVOPDataRateConfProfTable used for configuring the downstream transmission direction of channel #1. This object has read-write accessibility if 'direct' attachment-method of VoP to xDSL lines is implemented. |
| OCT hwVOPSetupInpDelayProf1Description | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.33 | OCTET STRING | read-create | This object identifies a row in hwVOPINPDelayConfProfTable used for configuring the INP-Delay parameters of channel #1. This object has read-write accessibility if 'direct' attachment-method of VoP to xDSL lines is implemented. |
| OCT hwVOPSetupUsDataRateProf2Description | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.34 | OCTET STRING | read-create | This object identifies a row in hwVOPDataRateConfProfTable used for configuring the upstream transmission direction of channel #2. If channel #2 is not being used this object should be set to a zero length string. This object has read-write accessibility if 'direct' attachment-method of VoP to xDSL lines is implemented. |
| OCT hwVOPSetupDsDataRateProf2Description | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.35 | OCTET STRING | read-create | This object identifies a row in hwVOPDataRateConfProfTable used for configuring the downstream transmission direction of channel #2. If channel #2 is not being used this object should be set to a zero length string. This object has read-write accessibility if 'direct' attachment-method of VoP to xDSL lines is implemented. |
| OCT hwVOPSetupInpDelayProf2Description | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.36 | OCTET STRING | read-create | This object identifies a row in hwVOPINPDelayConfProfTable used for configuring the INP-Delay parameters of channel #2. If channel #2 is not being used this object should be set to a zero length string. This object has read-write accessibility if 'direct' attachment-method of VoP to xDSL lines is implemented. |
| OCT hwVOPSetupLSpectrumProfDescription | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.37 | OCTET STRING | read-create | This object identifies a row in hwVOPLineSpectrumConfProfTable used for configuring the spectrum parameters of the respective xDSL line. This object has read-write accessibility if 'direct' attachment-method of VoP to xDSL lines is implemented. |
| OCT hwVOPSetupUpboProfDescription | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.38 | OCTET STRING | read-create | This object identifies a row in hwVOPUPBOConfProfTable used for configuring the upstream power back-off related parameters of the respective xDSL line. If this leaf is not support this object should be set to 0. This object has read-write accessibility if 'direct' attachment-method of VoP to xDSL lines is implemented. |
| OCT hwVOPSetupDpboProfDescription | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.39 | OCTET STRING | read-create | This object identifies a row in hwVOPDPBOConfProfTable used for configuring the downstream power back-off related parameters of the respective xDSL line. This object has read-write accessibility if 'direct' attachment-method of VoP to xDSL lines is implemented. |
| OCT hwVOPSetupRfiProfDescription | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.40 | OCTET STRING | read-create | This object identifies a row in hwVOPRFIConfProfTable used for configuring the RFI notches related parameters of the respective xDSL line. This object has read-write accessibility if 'direct' attachment-method of VoP to xDSL lines is implemented. |
| OCT hwVOPSetupNoiseMarginProfDescription | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.41 | OCTET STRING | read-create | This object identifies a row in hwVOPSNRMarginConfProfTable used for configuring the noise margin related parameters of the respective xDSL line. This object has read-write accessibility if 'direct' attachment-method of VoP to xDSL lines is implemented. |
| OCT hwVOPSetupVNoiseProfDescription | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.42 | OCTET STRING | read-create | This object identifies a row in hwVOPVirtualNoiseConfProfTable used for configuring the virtual noise related parameters of the respective xDSL line. This object has read-write accessibility if 'direct' attachment-method of VoP to xDSL lines is implemented. |
| OCT hwVOPSetupInmProfDescription | 1.3.6.1.4.1.2011.6.144.1.2.2.2.1.43 | OCTET STRING | read-create | This object identifies a row in hwVOPINMConfProfTable used for configuring the impulse noise monitoring parameters of the respective xDSL line. This object has read-write accessibility if 'direct' attachment-method of VoP to xDSL lines is implemented. |
| hwVOPActSetupTable | 1.3.6.1.4.1.2011.6.144.1.2.2.3 | not-accessible | This read-only table contains groups of profile indices actually attached to any xDSL line in the system. Each group of profile indices constructs a Vector Of Profiles (VoP). 1) A row in this table is automatically created or deleted by the SNMP agent together with creating or deleting a row in the xdsl2LineTable (VDSL2-LINE-MIB) for any xDSL line. 2) The row index is same as the index of the respective row in xdsl2LineTable. Thus, this table can be considered as extending the xdsl2LineTable. This table is mandatory in 'direct' attachment-method of VoP to xDSL lines but can optionally be implemented in 'indirect' attachment-method. The objects in this table reflect the actual configuration VoP of the respective xDSL line. A row in the table is automatically created by the SNMP agent when a respective row is created in the xdsl2LineTable. Implementing this table is mandatory in case the implementation uses 'direct' attachment-method of VoP to xDSL lines. Implementation is optional in case of 'indirect' attachment-method. The index of this table is hwVOPActSetupIndex. | |
| hwVOPActSetupEntry | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1 | not-accessible | This read-only table contains groups of profile indices actually attached to any xDSL line in the system. Each group of profile indices constructs a Vector Of Profiles (VoP). 1) A row in this table is automatically created or deleted by the SNMP agent together with creating or deleting a row in the xdsl2LineTable (VDSL2-LINE-MIB) for any xDSL line. 2) The row index is same as the index of the respective row in xdsl2LineTable. Thus, this table can be considered as extending the xdsl2LineTable. This table is mandatory in 'direct' attachment-method of VoP to xDSL lines but can optionally be implemented in 'indirect' attachment-method. The objects in this table reflect the actual configuration VoP of the respective xDSL line. A row in the table is automatically created by the SNMP agent when a respective row is created in the xdsl2LineTable. Implementing this table is mandatory in case the implementation uses 'direct' attachment-method of VoP to xDSL lines. Implementation is optional in case of 'indirect' attachment-method. The index of this entry is hwVOPActSetupIndex. | |
| U32 hwVOPActSetupIndex | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.1 | Unsigned32 | not-accessible | The hwVOPActSetupIndex identifies a row in this table. A row in this table is indexed by an ifIndex pattern. |
| U32 hwVOPActSetupUsDataRateProfId1 | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.2 | Unsigned32 | read-only | This object identifies a row in hwVOPDataRateConfProfTable used for configuring the upstream transmission direction of channel number #1. |
| U32 hwVOPActSetupUsRaRatio1 | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.3 | Unsigned32 | read-only | Rate Adaptation Ratio. The ratio (in %) that is taken into account for the bearer channel #1 when performing rate adaptation on upstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - hwVOPActSetupUsRaRatio1 is the ratio of excess data rate assigned to all other bearer channels on upstream direction. The sum of rate adaptation ratios over all bearers on the same direction is equal to 100%. |
| U32 hwVOPActSetupDsDataRateProfId1 | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.4 | Unsigned32 | read-only | This object identifies a row in hwVOPDataRateConfProfTable used for configuring the downstream transmission direction of channel #1. |
| U32 hwVOPActSetupDsRaRatio1 | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.5 | Unsigned32 | read-only | Rate Adaptation Ratio. The ratio (in %) that is taken into account for the bearer channel #1 when performing rate adaptation on downstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - hwVOPActSetupDsRaRatio1 is the ratio of excess data rate assigned to all other bearer channels on downstream direction. The sum of rate adaptation ratios over all bearers on the same direction is equal to 100%. |
| U32 hwVOPActSetupInpDelayProfId1 | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.6 | Unsigned32 | read-only | This object identifies a row in hwVOPINPDelayConfProfTable used for configuring the INP-Delay parameters of channel #1. |
| U32 hwVOPActSetupUsDataRateProfId2 | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.7 | Unsigned32 | read-only | This object identifies a row in hwVOPDataRateConfProfTable used for configuring the upstream transmission direction of channel #2. If channel #2 is not being used this object is set to 0. |
| U32 hwVOPActSetupUsRaRatio2 | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.8 | Unsigned32 | read-only | Rate Adaptation Ratio. The ratio (in %) that is taken into account for the bearer channel #2 when performing rate adaptation on upstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - hwVOPActSetupUsRaRatio2 is the ratio of excess data rate assigned to all other bearer channels on upstream direction. The sum of rate adaptation ratios over all bearers on the same direction is equal to 100%. |
| U32 hwVOPActSetupDsDataRateProfId2 | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.9 | Unsigned32 | read-only | This object identifies a row in hwVOPDataRateConfProfTable used for configuring the downstream transmission direction of channel #2. If channel #2 is not being used this object is set to 0. |
| U32 hwVOPActSetupDsRaRatio2 | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.10 | Unsigned32 | read-only | Rate Adaptation Ratio. The ratio (in %) that is taken into account for the bearer channel #2 when performing rate adaptation on downstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - hwVOPActSetupDsRaRatio2 is the ratio of excess data rate assigned to all other bearer channels on downstream direction. The sum of rate adaptation ratios over all bearers on the same direction is equal to 100%. |
| U32 hwVOPActSetupInpDelayProfId2 | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.11 | Unsigned32 | read-only | This object identifies a row in hwVOPINPDelayConfProfTable used for configuring the INP-Delay parameters of channel #2 If channel #2 is not being used this object is set to 0. |
| U32 hwVOPActSetupUsDataRateProfId3 | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.12 | Unsigned32 | read-only | This object identifies a row in hwVOPDataRateConfProfTable used for configuring the upstream transmission direction of channel #3. If channel #3 is not being used this object is set to 0. |
| U32 hwVOPActSetupUsRaRatio3 | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.13 | Unsigned32 | read-only | Rate Adaptation Ratio. The ratio (in %) that is taken into account for the bearer channel #3 when performing rate adaptation on upstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - hwVOPActSetupUsRaRatio3 is the ratio of excess data rate assigned to all other bearer channels on upstream direction. The sum of rate adaptation ratios over all bearers on the same direction is equal to 100%. |
| U32 hwVOPActSetupDsDataRateProfId3 | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.14 | Unsigned32 | read-only | This object identifies a row in hwVOPDataRateConfProfTable used for configuring the downstream transmission direction of channel #3. If channel #3 is not being used this object is set to 0. |
| U32 hwVOPActSetupDsRaRatio3 | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.15 | Unsigned32 | read-only | Rate Adaptation Ratio. The ratio (in %) that is taken into account for the bearer channel #3 when performing rate adaptation on downstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - hwVOPActSetupDsRaRatio3 is the ratio of excess data rate assigned to all other bearer channels on downstream direction. The sum of rate adaptation ratios over all bearers on the same direction is equal to 100%. |
| U32 hwVOPActSetupInpDelayProfId3 | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.16 | Unsigned32 | read-only | This object identifies a row in hwVOPINPDelayConfProfTable used for configuring the INP-Delay parameters of channel #3 If channel #3 is not being used this object is set to 0. |
| U32 hwVOPActSetupUsDataRateProfId4 | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.17 | Unsigned32 | read-only | This object identifies a row in hwVOPDataRateConfProfTable used for configuring the upstream transmission direction of channel #4. If channel #4 is not being used this object is set to 0. |
| U32 hwVOPActSetupUsRaRatio4 | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.18 | Unsigned32 | read-only | Rate Adaptation Ratio. The ratio (in %) that is taken into account for the bearer channel #4 when performing rate adaptation on upstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - hwVOPActSetupUsRaRatio4 is the ratio of excess data rate assigned to all other bearer channels on upstream direction. The sum of rate adaptation ratios over all bearers on the same direction is equal to 100%. |
| U32 hwVOPActSetupDsDataRateProfId4 | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.19 | Unsigned32 | read-only | This object identifies a row in hwVOPDataRateConfProfTable used for configuring the downstream transmission direction of channel #4. If channel #4 is not being used this object is set to 0. |
| U32 hwVOPActSetupDsRaRatio4 | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.20 | Unsigned32 | read-only | Rate Adaptation Ratio. The ratio (in %) that is taken into account for the bearer channel #4 when performing rate adaptation on downstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - hwVOPActSetupDsRaRatio4 is the ratio of excess data rate assigned to all other bearer channels on downstream direction. The sum of rate adaptation ratios over all bearers on the same direction is equal to 100%. |
| U32 hwVOPActSetupInpDelayProfId4 | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.21 | Unsigned32 | read-only | This object identifies a row in hwVOPINPDelayConfProfTable used for configuring the INP-Delay parameters of channel #4 If channel #4 is not being used this object is set to 0. |
| U32 hwVOPActSetupLSpectrumProfId | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.22 | Unsigned32 | read-only | This object identifies a row in hwVOPLineSpectrumConfProfTable used for configuring the spectrum parameters of the respective xDSL line. |
| U32 hwVOPActSetupNoiseMarginProfId | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.23 | Unsigned32 | read-only | This object identifies a row in hwVOPSNRMarginConfProfTable used for configuring the noise margin related parameters of the respective xDSL line. |
| U32 hwVOPActSetupVNoiseProfId | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.24 | Unsigned32 | read-only | This object identifies a row in hwVOPVirtualNoiseConfProfTable used for configuring the virtual noise related parameters of the respective xDSL line. |
| U32 hwVOPActSetupUpboProfId | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.25 | Unsigned32 | read-only | This object identifies a row in hwVOPUPBOConfProfTable used for configuring the upstream power back-off related parameters of the respective xDSL line. If this leaf is not support this object should be set to 0. |
| U32 hwVOPActSetupDpboProfId | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.26 | Unsigned32 | read-only | This object identifies a row in hwVOPDPBOConfProfTable used for configuring the downstream power back-off related parameters of the respective xDSL line. |
| U32 hwVOPActSetupRfiProfId | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.27 | Unsigned32 | read-only | This object identifies a row in hwVOPRFIConfProfTable used for configuring the RFI notches related parameters of the respective xDSL line. |
| U32 hwVOPActSetupInmProfId | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.28 | Unsigned32 | read-only | This object identifies a row in hwVOPINMConfProfTable used for configuring the impulse noise monitoring parameters of the respective xDSL line. |
| OCT hwVOPActSetupUsDataRateProf1Description | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.29 | OCTET STRING | read-only | This object identifies a row in hwVOPDataRateConfProfTable used for configuring the upstream transmission direction of channel number #1. |
| OCT hwVOPActSetupDsDataRateProf1Description | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.30 | OCTET STRING | read-only | This object identifies a row in hwVOPDataRateConfProfTable used for configuring the downstream transmission direction of channel #1. |
| OCT hwVOPActSetupInpDelayProf1Description | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.31 | OCTET STRING | read-only | This object identifies a row in hwVOPINPDelayConfProfTable used for configuring the INP-Delay parameters of channel #1. |
| OCT hwVOPActSetupUsDataRateProf2Description | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.32 | OCTET STRING | read-only | This object identifies a row in hwVOPDataRateConfProfTable used for configuring the upstream transmission direction of channel #2. |
| OCT hwVOPActSetupDsDataRateProf2Description | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.33 | OCTET STRING | read-only | This object identifies a row in hwVOPDataRateConfProfTable used for configuring the downstream transmission direction of channel #2. |
| OCT hwVOPActSetupInpDelayProf2Description | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.34 | OCTET STRING | read-only | This object identifies a row in hwVOPINPDelayConfProfTable used for configuring the INP-Delay parameters of channel #2 |
| OCT hwVOPActSetupLSpectrumProfDescription | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.35 | OCTET STRING | read-only | This object identifies a row in hwVOPLineSpectrumConfProfTable used for configuring the spectrum parameters of the respective xDSL line. |
| OCT hwVOPActSetupUpboProfDescription | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.36 | OCTET STRING | read-only | This object identifies a row in hwVOPUPBOConfProfTable used for configuring the upstream power back-off related parameters of the respective xDSL line. If this leaf is not support this object should be set to 0. |
| OCT hwVOPActSetupDpboProfDescription | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.37 | OCTET STRING | read-only | This object identifies a row in hwVOPDPBOConfProfTable used for configuring the downstream power back-off related parameters of the respective xDSL line. |
| OCT hwVOPActSetupRfiProfDescription | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.38 | OCTET STRING | read-only | This object identifies a row in hwVOPRFIConfProfTable used for configuring the RFI notches related parameters of the respective xDSL line. |
| OCT hwVOPActSetupNoiseMarginProfDescription | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.39 | OCTET STRING | read-only | This object identifies a row in hwVOPSNRMarginConfProfTable used for configuring the noise margin related parameters of the respective xDSL line. |
| OCT hwVOPActSetupVNoiseProfDescription | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.40 | OCTET STRING | read-only | This object identifies a row in hwVOPVirtualNoiseConfProfTable used for configuring the virtual noise related parameters of the respective xDSL line. |
| OCT hwVOPActSetupInmProfDescription | 1.3.6.1.4.1.2011.6.144.1.2.2.3.1.41 | OCTET STRING | read-only | This object identifies a row in hwVOPINMConfProfTable used for configuring the impulse noise monitoring parameters of the respective xDSL line. |
| hwVOPConformance | 1.3.6.1.4.1.2011.6.144.2 | |||
| hwVOPGroups | 1.3.6.1.4.1.2011.6.144.2.1 | |||
| hwVOPTraps | 1.3.6.1.4.1.2011.6.144.3 | |||
| hwVOPCommonTraps | 1.3.6.1.4.1.2011.6.144.3.1 | |||
| hwVOPXdslPortTraps | 1.3.6.1.4.1.2011.6.144.3.1.1 | |||
| NTF hwVOPProfileIDChangeTrap | 1.3.6.1.4.1.2011.6.144.3.1.1.1 | The profile ID bound by the port change. 1. hwConfigChangeIP -- The serial IP of configuration changes. 2. ifIndex-the index of the xDSL interface. 3. hwVOPDataRateConfProfIndex -- the data-rate profile ID used for configuring the downstream transmission direction of channel #1. 4. hwVOPDataRateConfProfDescription-the data-rate profile description used for configuring the downstream transmission direction of channel #1. 5. hwVOPDataRateConfProfIndex -- the data-rate profile ID used for configuring the upstream transmission direction of channel #1. 6. hwVOPDataRateConfProfDescription -- the data-rate profile description used for configuring the upstream transmission direction of channel #1. 7. hwVOPINPDelayConfProfIndex -- the inp-delay profile ID used for configuring the channel #1. 8. hwVOPINPDelayConfProfDescription -- the inp-delay profile description used for configuring the channel #1. 9. hwVOPDataRateConfProfIndex -- the data-rate profile ID used for configuring the downstream transmission direction of channel #2. 10.hwVOPDataRateConfProfDescription -- the data-rate profile description used for configuring the downstream transmission direction of channel #2. 11.hwVOPDataRateConfProfIndex -- the data-rate profile ID used for configuring the upstream transmission direction of channel #2. 12.hwVOPDataRateConfProfDescription -- the data-rate profile description used for configuring the upstream transmission direction of channel #2. 13.hwVOPINPDelayConfProfIndex -- the inp-delay profile ID used for configuring the channel #2. 14.hwVOPINPDelayConfProfDescription -- the inp-delay profile description used for configuring the channel #2. 15.hwVOPDPBOConfProfIndex -- the dpbo profile ID used for configuring the port. 16.hwVOPDPBOConfProfProfDescription -- the dpbo profile description used for configuring the port. 17.hwVOPUPBOConfProfIndex -- the upbo profile ID used for configuring the port. 18.hwVOPUPBOConfProfDescription -- the upbo profile description used for configuring the port. 19.hwVOPLineSpectrumConfProfIndex -- the line-spectrum profile ID used for configuring the port. 20.hwVOPLineSpectrumConfProfDescription -- the line-spectrum profile description used for configuring the port. 21.hwVOPRFIConfProfIndex -- the rfi profile ID used for configuring the port. 22.hwVOPRFIConfProfDescription -- the rfi profile description used for configuring the port. 23.hwVOPSNRMarginConfProfIndex -- the SNR-Margin profile ID used for configuring the port. 24.hwVOPSNRMarginConfProfDescription -- the SNR-Margin profile description used for configuring the port. 25.hwVOPVirtualNoiseConfProfIndex -- the virtual noise profile ID used for configuring the port. 26.hwVOPVirtualNoiseConfProfDescription -- the virtual noise profile description used for configuring the port. 27.hwVOPINMConfProfIndex -- the inm profile ID used for configuring the port. 28.hwVOPINMConfProfDescription -- the inm profile description used for configuring the port. | ||
| hwVOPAlarmTraps | 1.3.6.1.4.1.2011.6.144.3.2 |
RFC description
A Huawei proprietary MIB providing SNMP management objects for Voice over Packet (VoP) protocols and voice communication functions on Huawei network devices and IP communications platforms.
Start monitoring Huawei broadband access gateway / xDSL voice-enabled CPE (TR-165 Vector-of-Profiles) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.