All MIBs › HUAWEI-ISIS-CONF-MIB
Organization: Huawei Technologies Co.,Ltd.
Last Updated: 2015-10-15
Category: Routing Protocols, Vendor: Huawei
Description: Huawei IS-IS conformance MIB defining conformance groups and compliance statements for Huawei IS-IS routing protocol management.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is HUAWEI-ISIS-CONF-MIB?
HUAWEI-ISIS-CONF-MIB is a Huawei private conformance MIB that defines the conformance groups and compliance statements for Huawei's IS-IS (Intermediate System to Intermediate System) routing protocol implementation, rather than the IS-IS runtime data objects themselves. It exists purely to declare which object groups and notifications a compliant Huawei device implementation must support for IS-IS management, serving as the compliance/testing companion to Huawei's IS-IS data-carrying MIB(s). As a conformance module it contains no pollable status, performance, or fault objects of its own, so it has no direct role in monitoring hardware or software runtime state; its value is purely in defining implementation requirements for tooling and compliance verification. It is entirely dependent on the corresponding Huawei IS-IS data MIB (and implicitly the IETF ISIS-MIB model) whose groups it references in its compliance statements. It is used by Huawei routers/switches running IS-IS and by NMS/compiler tooling validating IS-IS MIB support during integration testing. Engineers can download the HUAWEI-ISIS-CONF-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in HUAWEI-ISIS-CONF-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Huawei router/switch running IS-IS
Monitoring Examples
This module is a conformance/compliance-statement MIB and defines no runtime monitoring objects itself, matching its empty sample_objects list; it only specifies which IS-IS object groups (e.g., interface, area, and adjacency groups from the companion data MIB) must be implemented for compliance. No realistic monitoring scenario can be honestly constructed from this module alone since it carries no pollable OIDs.
This MIB depends on
Related MIBs
Imported Objects
From HUAWEI-MIB
| hwDatacomm | OBJECT-IDENTITY |
From IF-MIB
| ifName | OBJECT-TYPE |
From ISIS-MIB
| isisAdjState | OBJECT-TYPE |
| isisCircIfIndex | OBJECT-TYPE |
| isisPduLspId | OBJECT-TYPE |
| isisSysInstance | |
| isisSysLevelIndex | OBJECT-TYPE |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Integer32 | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TruthValue |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| hwISIS | 1.3.6.1.4.1.2011.5.25.24 | The HUAWEI PRIVATE MIB contains objects belonging to processes of the IS-IS protocol existing on the system. It defines the model used to represent data that exists elsewhere in the system and on peripheral devices. There are no constraints on this MIB. | ||
| hwIsisConf | 1.3.6.1.4.1.2011.5.25.24.2 | |||
| hwIsisMIBObjects | 1.3.6.1.4.1.2011.5.25.24.2.1 | |||
| hwIsisProcBaseTable | 1.3.6.1.4.1.2011.5.25.24.2.1.1 | not-accessible | The set of commands of the Integrated IS-IS protocol existing on the system. | |
| hwIsisProcBaseEntry | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1 | not-accessible | Each row defines some commmands to a single process of the IS-IS protocol existing on the system. These commands belong to the IS-IS process. | |
| I32 hwIsisProcIdIndex | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.1 | Integer32 | not-accessible | The value of this object identifies the IS-IS process ID. The value ranges from 1 to 65535. |
| OCT hwIsisProcVpnName | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.2 | OCTET STRING | read-create | The value of this object identifies the name of the IPv4 VPN instance bound to the IS-IS process. The value ranges from 0 to 31. |
| OCT hwIsisProcVpn6Name | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.3 | OCTET STRING | read-create | The value of this object identifies the name of the IPv6 VPN instance bound to the IS-IS process. The value ranges from 0 to 31. |
| INT hwIsisProcAreaAuthType | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.4 | INTEGER | read-create | The value of this object identifies the type of IS-IS area authentication. null (0): Area authentication is not configured. md5 (1): The password is sent after being encrypted through MD5. simple (2): The password is sent in the form of simple text. keychain (3): The key chain table that changes with time is sent after being encrypted through MD5. By default, area authentication is not configured. |
| OCT hwIsisProcAreaAuthPasswordName | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.5 | OCTET STRING | read-create | This object indicates the password of IS-IS area authentication. The password is a string of characters. If the IS-IS area authentication mode is simple, the password is a string of 0 to 16 characters. If the IS-IS area authentication mode is MD5, the password is a string of 0 to 392 characters. If the IS-IS area authentication mode is keychain, the name is a string of 0 to 47 characters. The length 0 indicates that no IS-IS area authentication password is configured. When read, it always returns length 0. |
| INT hwIsisProcAreaAuthPacketAuthMode | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.6 | INTEGER | read-create | The value of this object identifies the packet authentication mode of IS-IS area authentication: none (0): Authentication mode is not configured. authenticateall (1): Encapsulates authentication information for both transmitted and received LSPs and SNPs. allsendonly (2): Encapsulates authentication information for both generated LSPs and SNPs; does not authenticate received LSPs or SNPs. snppacketauthenticationavoid (3): Encapsulates authentication information for only generated LSPs and authenticates received LSPs. snppacketsendonly (4): Encapsulates authentication information for generated LSPs and SNPs; authenticates only received LSPs but does not authenticate received SNPs. By default, authentication is not configured. |
| INT hwIsisProcAreaAuthCode | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.7 | INTEGER | read-create | The value of this object identifies the code of area authentication. none (0): The authentication code is not configured. osi (10): indicates OSI authentication. ip (133): indicates IP authentication. |
| INT hwIsisProcDomainAuthType | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.8 | INTEGER | read-create | The value of this object identifies the type of IS-IS router domain authentication. null (0): Domain authentication is not configured. md5 (1): The password is sent after being encrypted through MD5. simple (2): The password is sent in the form of simple text. keychain (3): The key chain table that changes with time is sent after being encrypted through MD5. By default, IS-IS route domain authentication is disabled. |
| OCT hwIsisProcDomainAuthPasswordName | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.9 | OCTET STRING | read-create | This object indicates the password of IS-IS routing domain authentication. The password is a string of characters. If the IS-IS routing domain authentication mode is simple, the password is a string of 0 to 16 characters. If the IS-IS routing domain authentication mode is MD5, the password is a string of 0 to 392 characters. If the IS-IS routing domain authentication mode is keychain, the name is a string of 0 to 47 characters. The length 0 indicates that the password of IS-IS routing domain authentication is not configured. When read, it always returns length 0. |
| INT hwIsisProcDomainAuthPacketAuthMode | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.10 | INTEGER | read-create | The value of this object identifies the packet authentication mode of IS-IS route domain authentication. none (0): Authentication mode is not configured. authenticateall (1): Encapsulates authentication information for both transmitted and received LSPs and SNPs. allsendonly (2): Encapsulates authentication information for both generated LSPs and SNPs; does not authenticate received LSPs or SNPs. snppacketauthenticationavoid (3): Encapsulates authentication information for only generated LSPs and authenticates received LSPs. snppacketsendonly (4): Encapsulates authentication information for generated LSPs and SNPs; authenticates only received LSPs but does not authenticate received SNPs. By default, authentication is not configured. |
| INT hwIsisProcDomainAuthCode | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.11 | INTEGER | read-create | The value of this object identifies the code of domain authentication. none (0): The authentication code is not configured. osi (10): indicates OSI authentication. ip (133): indicates IP authentication. |
| INT hwIsisProcLevel | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.12 | INTEGER | read-create | The value of this object identifies the level of the IS-IS process. level1 (1): indicates level 1. level2 (2): indicates level 2. level12 (3): indicates level 1-2. By default, the level of an IS-IS process is level-1-2. |
| I32 hwIsisProcL1FlashFloodCount | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.13 | Integer32 | read-create | The value of this object identifies the counter of level-1 LSPs on the interface. The value is an integer ranging from 0 to 15. The value 0 indicates that no counter is configured. The default value is 5. |
| I32 hwIsisProcL1FlashFloodInterval | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.14 | Integer32 | read-create | The value of this object identifies the intervals for level-1 LSP flooding. The value ranges from 10 to 50000, in milliseconds. The default value is 10 ms. |
| I32 hwIsisProcL2FlashFloodCount | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.15 | Integer32 | read-create | The value of this object identifies the counter of level-2 LSPs on the interface. The value is an integer ranging from 0 to 15. The value 0 indicates that no counter is configured. The default value is 5. |
| I32 hwIsisProcL2FlashFloodInterval | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.16 | Integer32 | read-create | The value of this object identifies the intervals for level-2 LSP flooding. The value ranges from 10 to 50000 in milliseconds. The default value is 10ms. |
| INT hwIsisProcLogPeerChange | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.17 | INTEGER | read-create | Generates a log when the status of the peer changes. null (0): not configured enabledwithouttopology (1): IPv4 topology enabledwithtopology (2): IPv6 topology |
| I32 hwIsisProcTimerRefresh | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.18 | Integer32 | read-create | The value of this object identifies the timer of LSP refreshing. The value ranges from 1 to 65534, in seconds. The default value is 900s. |
| I32 hwIsisProcTimerMaxAge | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.19 | Integer32 | read-create | The value of this object identifies the maximum Keepalive time of the LSP. The value ranges from 2 to 65535, in seconds. The default value is 1200s. |
| I32 hwIsisProcL1TimerLspGenMaxInterval | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.20 | Integer32 | read-create | The value of this object identifies the timer for the maximum delay of level-1 LSPs with the same LSP ID. The value ranges from 1 to 120, in seconds. By default, the value is 2s. |
| I32 hwIsisProcL1TimerLspGenInitInterval | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.21 | Integer32 | read-create | The value of this object identifies the delay timer that initially triggers a level-1 LSP. The value ranges from 0 to 60000, in milliseconds. By default, the value is 0. |
| I32 hwIsisProcL1TimerLspGenIncrInterval | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.22 | Integer32 | read-create | The value of this object identifies the delay timer for generating two level-1 LSPs with the same LSP ID. The value ranges from 1 to 60000, in milliseconds. By default, the value is 0. |
| I32 hwIsisProcL2TimerLspGenMaxInterval | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.23 | Integer32 | read-create | The value of this object identifies the timer for the maximum delay of Level-2 LSPs with the same LSP ID. The value ranges from 1 to 120, in seconds. By default, the value is 2s. |
| I32 hwIsisProcL2TimerLspGenInitInterval | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.24 | Integer32 | read-create | The value of this object identifies the delay timer that initially triggers a Level-2 LSP. The value ranges from 1 to 60000, in milliseconds. By default, the value is 0. |
| I32 hwIsisProcL2TimerLspGenIncrInterval | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.25 | Integer32 | read-create | The value of this object identifies the delay timer for generating two Level-2 LSPs with the same LSP ID. The value ranges from 1 to 60000, in milliseconds. By default, the value is 0. |
| I32 hwIsisProcTimerSPFMaxInterval | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.26 | Integer32 | read-create | The value of this object identifies the maximum intervals for SPF calculation. The value ranges from 1 to 120, in seconds. By default, the value is 5s. |
| I32 hwIsisProcTimerSPFInitInterval | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.27 | Integer32 | read-create | The value of this object identifies the delay timer for initial SPF calculation. The value ranges from 1 to 60000, in milliseconds. By default, the interval is 50ms. |
| I32 hwIsisProcTimerSPFIncrInterval | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.28 | Integer32 | read-create | The value of this object identifies the incremental delay timer for two SPF calculations. The value ranges from 1 to 60000, in milliseconds. By default, the interval is 200ms. |
| INT hwIsisProcCostStyle | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.29 | INTEGER | read-create | Configures the cost type of the IS-IS process: narrow (1): the narrow type narrowcompatible (2): the narrow-compatible type compatible (3): compatible type wide (4): wide type widecompatible (5): wide-compatible type narrowcompatiblerelax (6): narrow-compatible relax-spf-limit type compatible-relax (7): compatible relax-spf-limit type By default, the cost type of an IS-IS process is narrow. |
| OCT hwIsisProcDynamicName | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.30 | OCTET STRING | read-create | Configures the name of the IS-IS dynamic host. The value is a string of 1 to 64 characters. When the length is 0, the configured IS-IS dynamic host name is deleted. |
| T/F hwIsisProcGREnabled | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.31 | TruthValue | read-create | Whether to enable IS-IS GR. true (1): enables IS-IS GR. false (2): does not enable IS-IS GR. By default, IS-IS GR is disabled. |
| I32 hwIsisProcGRInterval | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.32 | Integer32 | read-create | The value of this object identifies the maximum intervals for enabling GR. The value ranges from 0 to 1800, in seconds. By default, the value is 300 seconds. The value 0 indicates that GR is not configured. |
| T/F hwIsisProcGRSuppresSAEnabled | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.33 | TruthValue | read-create | This object indicates that the SA bit in the sent Hello packet is set to 1 after the GR-enabled device is started: true (1): enables this function. false (2): disables this function. By default, IS-IS does not suppress Hello PDUs from carrying SA bits. |
| INT hwIsisProcTEEnableLevel | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.34 | INTEGER | read-create | Enables IS-IS TE. none (0): does not enable IS-IS TE. level1 (1): enables level-1 TE. level2 (2): enables level-2 TE. level12 (3): enables level-1-2 TE. By default, IS-IS TE is disabled. |
| T/F hwIsisProcBFDEnabled | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.35 | TruthValue | read-create | Whether to enable BFD on each interface. true (1): enables BFD on each interface. false (2): does not enable BFD on each interface. By default, BFD is disabled on each interface. |
| T/F hwIsisProcBFDFrrBindEnabled | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.36 | TruthValue | read-create | Enables BFD-FRR binding on each interface. true (1): enables BFD-FRR binding on each interface. false (2): does not enable BFD-FRR binding on each interface. By default, BFD-FRR binding is disabled on each interface. |
| I32 hwIsisProcBFDMinTxInterval | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.37 | Integer32 | read-create | The value of this object identifies the minimum interval for sending BFD packets. If isis binding to vpn and ipv4-family not enable, The value is zero. |
| I32 hwIsisProcBFDMinRecvInteval | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.38 | Integer32 | read-create | The value of this object identifies the minimum interval for receiving BFD packets. If isis binding to vpn and ipv4-family not enable, The value is zero. |
| I32 hwIsisProcBFDMultiplier | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.39 | Integer32 | read-create | The value of this object identifies the local detection multiplier. The value ranges from 1 to 255. If isis binding to vpn and ipv4-family not enable, The value is zero. |
| INT hwIsisProcIPv6EnableTopologyType | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.40 | INTEGER | read-create | This objects indicates whether the IPv6 topology is enabled for the IS-IS process: disable(0): disables the IPv6 topology of the IS-IS process. standard(1): specifies the topology type as the standard mode. ipv6(2): enables IPv6 for the IS-IS process in the IPv6 topology. compatible(3): specifies the topology type as the compatible mode. compatibleenablemtspf(4): indicates that SPF calculation is performed in the IPv6 topology in compatible mode. By default, the IPv6 topology is not enabled for the IS-IS process. |
| ROW hwIsisProcRowStatus | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.41 | RowStatus | read-create | This object supports settings of two values. createAndGo(4): A row is created. destroy(6): A row is deleted. |
| T/F hwIsisProcOptionalChecksumEnabled | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.42 | TruthValue | read-create | Enables BFD-FRR binding on each interface. true (1): enables optional checksum for CSNP,PSNP and IIH PDU. false (2): disables optional checksum for CSNP,PSNP and IIH PDU. By default, optional checksum is disabled. |
| U32 hwisisProcLsdbMaxLimit | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.43 | Unsigned32 | read-create | This object is used to set the maximum limit number of IS-IS LSPs. The value range is from 0 to 500000. The default value 0 means no limit. |
| U32 hwIsisProcLsdbUpperThreshold | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.44 | Unsigned32 | read-create | This object is used to set the upper threshold value of LSPs limit. The value range is from 1 to 100. The default means 80. |
| U32 hwIsisProcLsdbLowerThreshold | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.45 | Unsigned32 | read-create | This object is used to set the lower threshold value of LSPs limit. The value range is from 1 to 100. The default means 70. |
| U32 hwIsisProcLsdbTotal | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.46 | Unsigned32 | read-only | This object is used to get the number of IS-IS LSPs. |
| OCT hwIsisProcAreaAuthKeychainName | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.47 | OCTET STRING | read-create | This object indicates the keychain name of IS-IS area authentication. The name is a string of characters. The name is a string of 0 to 47 characters. The length 0 indicates that no IS-IS area authentication keychain name is configured. When read, it returns the keychain name. |
| OCT hwIsisProcDomainAuthKeychainName | 1.3.6.1.4.1.2011.5.25.24.2.1.1.1.48 | OCTET STRING | read-create | This object indicates the keychain name of IS-IS domain authentication. The name is a string of characters. The name is a string of 0 to 47 characters. The length 0 indicates that no IS-IS domain authentication keychain name is configured. When read, it returns the keychain name. |
| hwIsisNETTable | 1.3.6.1.4.1.2011.5.25.24.2.1.2 | not-accessible | Set of network entities of process. | |
| hwIsisNETEntry | 1.3.6.1.4.1.2011.5.25.24.2.1.2.1 | not-accessible | Each row means one network entity of the process. | |
| OCT hwIsisNETIndex | 1.3.6.1.4.1.2011.5.25.24.2.1.2.1.1 | OCTET STRING | not-accessible | The value of this object identifies the NET index. It is a string of 8 to 20 bytes. |
| ROW hwIsisNETStatus | 1.3.6.1.4.1.2011.5.25.24.2.1.2.1.2 | RowStatus | read-create | The value of this object identifies the status of the NET table. createAndGo(4): A row is created. destroy(6): A row is deleted. |
| hwIsisProcMTExtTable | 1.3.6.1.4.1.2011.5.25.24.2.1.3 | not-accessible | Set of commands of the integrated IS-IS protocol existing on the system, which are different for IP type and MT. | |
| hwIsisProcMTExtEntry | 1.3.6.1.4.1.2011.5.25.24.2.1.3.1 | not-accessible | Each row defines some commands specific to a single process of the IS-IS protocol existing on the system. These commands are different from ProcBaseTable for IP type and MT. | |
| IPt hwIsisIpTypeIndex | 1.3.6.1.4.1.2011.5.25.24.2.1.3.1.1 | InetAddressType | not-accessible | This object indicates the IP protocol type: ipv4(1): indicates IPv4. ipv6(2): indicates IPv6. |
| I32 hwIsisMTIdIndex | 1.3.6.1.4.1.2011.5.25.24.2.1.3.1.2 | Integer32 | not-accessible | The value of this object identifies the MT ID. |
| OCT hwIsisMTName | 1.3.6.1.4.1.2011.5.25.24.2.1.3.1.3 | OCTET STRING | read-create | This object indicates the name of the topology to be bound to an IS-IS process. The value is a string of 1 to 31 characters. |
| INT hwIsisProcDefRoutAdvType | 1.3.6.1.4.1.2011.5.25.24.2.1.3.1.4 | INTEGER | read-create | This object is used to set the mode in which default routes are advertised: null(0): indicates that default routes are not advertised. always(1): indicates that default routes are always advertised. matchdefault(2): If there is the default route that is generated by another routing protocol or another IS-IS process in the routing table, this default route is advertised in an LSP. If this default route is deleted from the routing table, this default route is not advertised in the LSP. routepolicy(3): indicates that default routes are advertised according to the routing policy. |
| OCT hwIsisProcDefRoutAdvPolicyName | 1.3.6.1.4.1.2011.5.25.24.2.1.3.1.5 | OCTET STRING | read-create | This object indicates the routing policy name. The name is a string of 0 to 40 characters. |
| U32 hwIsisProcDefRoutAdvCost | 1.3.6.1.4.1.2011.5.25.24.2.1.3.1.6 | Unsigned32 | read-create | This object is used to set the cost of a default route. |
| U32 hwIsisProcDefRoutAdvTag | 1.3.6.1.4.1.2011.5.25.24.2.1.3.1.7 | Unsigned32 | read-create | This object is used to set the administrative tag of a default route. |
| INT hwIsisProcDefRoutAdvLevel | 1.3.6.1.4.1.2011.5.25.24.2.1.3.1.8 | INTEGER | read-create | This object is used to set the level of a default route: level1(1): indicates Level-1. level2(2): indicates Level-2. level12(3): indicates Level-1-2. By default, the level of a default route is Level-2. |
| T/F hwIsisProcDefRoutAdvAvoidLearnEnabled | 1.3.6.1.4.1.2011.5.25.24.2.1.3.1.9 | TruthValue | read-create | This object indicates whether an IS-IS process is prevented from learning default routes or adding them to the routing table: true(1): indicates that an IS-IS process is prevented from learning default routes or adding them to the routing table. false(2): indicates that an IS-IS process can learn default routes and then add them to the routing table. By default, an IS-IS process can learn default routes and then add them to the routing table. |
| I32 hwIsisProcL1CircuitCost | 1.3.6.1.4.1.2011.5.25.24.2.1.3.1.10 | Integer32 | read-create | Global level-1 cost for all the interfaces. If the costStyle of the process is wide or widecompatible, the range of this value is from 1 to 16777215, else the range of this value is from 1 to 63. |
| I32 hwIsisProcL2CircuitCost | 1.3.6.1.4.1.2011.5.25.24.2.1.3.1.11 | Integer32 | read-create | Global level-2 cost for all the interfaces. If the costStyle of the process is wide or widecompatible, the range of this value is from 1 to 16777215, else the range of this value is from 1 to 63. |
| I32 hwIsisProcPrefValue | 1.3.6.1.4.1.2011.5.25.24.2.1.3.1.12 | Integer32 | read-create | This object is used to set the preference of an IS-IS route. The value ranges from 1 to 255, and the default value is 15. If isis binding to vpn and ip-family not enable, The value is zero. |
| OCT hwIsisProcPrefPolicyName | 1.3.6.1.4.1.2011.5.25.24.2.1.3.1.13 | OCTET STRING | read-create | This object indicates the name of the routing policy used for route filtering. The name is a string of 0 to 40 characters. Zero-length means no configuration. |
| I32 hwIsisProcMaxLoadBalance | 1.3.6.1.4.1.2011.5.25.24.2.1.3.1.14 | Integer32 | read-create | This object is used to set the number of equal-cost routes. The range and the default value depend on license. If isis binding to vpn and ip-family not enable, The value is zero. |
| U32 hwIsisProcL1CircuitDefaultTag | 1.3.6.1.4.1.2011.5.25.24.2.1.3.1.15 | Unsigned32 | read-create | This object is used to set the default administrative tag of an IS-IS Level-1 route. |
| U32 hwIsisProcL2CircuitDefaultTag | 1.3.6.1.4.1.2011.5.25.24.2.1.3.1.16 | Unsigned32 | read-create | This object is used to set the default administrative tag of an IS-IS Level-2 route. |
| U32 hwIsisProcBandWidthReference | 1.3.6.1.4.1.2011.5.25.24.2.1.3.1.17 | Unsigned32 | read-create | This object is used to set the reference bandwidth. |
| T/F hwIsisProcAutoCostEnabled | 1.3.6.1.4.1.2011.5.25.24.2.1.3.1.18 | TruthValue | read-create | This object indicates whether automatic interface cost calculation is enabled: true(1): indicates that automatic interface cost calculation is enabled. false(2): indicates that automatic interface cost calculation is disabled. By default, automatic interface cost calculation is disabled. |
| INT hwIsisProcSetOverLoad | 1.3.6.1.4.1.2011.5.25.24.2.1.3.1.19 | INTEGER | read-create | This object indicates whether a device is enabled to notify its neighbors that its status is Overload: disable (0): indicates that a device is disabled from notifying its neighbors that its status is Overload. enable(1): indicates that a device is enabled to notify its neighbors that its status is Overload. onstartup(2): When a device is restarted or becomes faulty, it notifies its neighbors that its status is Overload. |
| INT hwIsisProcSetOverLoadAllowRoute | 1.3.6.1.4.1.2011.5.25.24.2.1.3.1.20 | INTEGER | read-create | This object indicates that the type of routes to be advertised when a device is in the Overload state: null(0): indicates that no route type is specified. external(1): indicates the imported external routes. interlevel(2): indicates the leak routes. externalandinterlevel(3): indicates the imported external and leak routes. |
| I32 hwIsisProcOnStartInterval | 1.3.6.1.4.1.2011.5.25.24.2.1.3.1.21 | Integer32 | read-create | The value of this object identifies the interval for waiting to clear the overload bit after the system is started. The value ranges from 5 to 86400, in seconds. The default value is 600s. |
| OCT hwIsisProcOnStartStartFromPeer | 1.3.6.1.4.1.2011.5.25.24.2.1.3.1.22 | OCTET STRING | read-create | This object indicates the system ID of a neighbor. |
| I32 hwIsisProcOnStartFromPeerInterval | 1.3.6.1.4.1.2011.5.25.24.2.1.3.1.23 | Integer32 | read-create | The value of this object identifies the maximum interval for waiting to clear the overload bit after the system is started and the neighbor relationship is established. The value ranges of set is from 5 to 86400, in seconds. The default value is 1200s. 0 means no configuration. |
| T/F hwIsisProcOnStartWaitForBgpEnabled | 1.3.6.1.4.1.2011.5.25.24.2.1.3.1.24 | TruthValue | read-create | This object indicates whether the function of waiting for BGP convergence is enabled: true(1): indicates that the function of waiting for BGP convergence is enabled. false(2): indicates that the function of waiting for BGP convergence is disabled. By default, the function of waiting for BGP convergence is disabled. |
| ROW hwIsisProcMTStatus | 1.3.6.1.4.1.2011.5.25.24.2.1.3.1.25 | RowStatus | read-create | This object indicates the row status of this table: createAndGo(4): indicates that a row is created. destroy(6): indicates that a row is deleted. |
| U32 hwIsisProcL1RedistMaxLimit | 1.3.6.1.4.1.2011.5.25.24.2.1.3.1.26 | Unsigned32 | read-create | This object is used to set the maximum limit number of IS-IS Level-1 redistribute routes advertised in LSPs. The value range is from 0 to 10000000. The default value 0 means no limit. |
| U32 hwIsisProcL2RedistMaxLimit | 1.3.6.1.4.1.2011.5.25.24.2.1.3.1.27 | Unsigned32 | read-create | This object is used to set the maximum limit number of IS-IS Level-2 redistribute routes advertised in LSPs. The value range is from 0 to 10000000. The default value 0 means no limit. |
| U32 hwIsisProcL1UpperRedistThreshold | 1.3.6.1.4.1.2011.5.25.24.2.1.3.1.28 | Unsigned32 | read-create | This object is used to set the upper threshold value of level-1 import limit. The value range is from 1 to 100. The default means 80. |
| U32 hwIsisProcL2UpperRedistThreshold | 1.3.6.1.4.1.2011.5.25.24.2.1.3.1.29 | Unsigned32 | read-create | This object is used to set the upper threshold value of level-2 import limit. The value range is from 1 to 100. The default means 80. |
| U32 hwIsisProcL1LowerRedistThreshold | 1.3.6.1.4.1.2011.5.25.24.2.1.3.1.30 | Unsigned32 | read-create | This object is used to set the lower threshold value of level-1 import limit. The value range is from 1 to 100. The default means 70. |
| U32 hwIsisProcL2LowerRedistThreshold | 1.3.6.1.4.1.2011.5.25.24.2.1.3.1.31 | Unsigned32 | read-create | This object is used to set the lower threshold value of level-2 import limit. The value range is from 1 to 100 The default means 70. |
| U32 hwIsisProcL1TotalRedist | 1.3.6.1.4.1.2011.5.25.24.2.1.3.1.32 | Unsigned32 | read-only | This object is used to get the number of level-1 import routes. |
| U32 hwIsisProcL2TotalRedist | 1.3.6.1.4.1.2011.5.25.24.2.1.3.1.33 | Unsigned32 | read-only | This object is used to get the number of level-2 import routes. |
| hwIsisPrefixPriorityTable | 1.3.6.1.4.1.2011.5.25.24.2.1.4 | not-accessible | Set of commands of priority-based convergence. | |
| hwIsisPrefixPriorityEntry | 1.3.6.1.4.1.2011.5.25.24.2.1.4.1 | not-accessible | Entry of priority-based convergence, each entry means one priority-based command for IS-IS process. | |
| INT hwIsisPrefixPriorityTypeIndex | 1.3.6.1.4.1.2011.5.25.24.2.1.4.1.1 | INTEGER | not-accessible | This object indicates the preference of a route: medium(1): indicates medium. high(2): indicates high. critical(3): indicates critical. |
| INT hwIsisPrefixPriorityL1PolicyType | 1.3.6.1.4.1.2011.5.25.24.2.1.4.1.2 | INTEGER | read-create | This object indicates the type of a Level-1 route preference policy: none(0): indicates that no policy type is specified. prefix(1): indicates the IP prefix policy. tag(2): indicates the administrative tag policy. |
| INT hwIsisPrefixPriorityL2PolicyType | 1.3.6.1.4.1.2011.5.25.24.2.1.4.1.3 | INTEGER | read-create | This object indicates the type of a Level-2 route preference policy: none(0): indicates that no policy type is specified. prefix(1): indicates the IP prefix policy. tag(2): indicates the administrative tag policy. |
| OCT hwIsisPrefixPriorityL1IpPrefixName | 1.3.6.1.4.1.2011.5.25.24.2.1.4.1.4 | OCTET STRING | read-create | This object indicates the name of a Level-1 IP prefix policy. The name is a string of 0 to 169 characters. Zero-length means no configuration. |
| OCT hwIsisPrefixPriorityL2IpPrefixName | 1.3.6.1.4.1.2011.5.25.24.2.1.4.1.5 | OCTET STRING | read-create | This object indicates the name of a Level-2 IP prefix policy. The name is a string of 0 to 169 characters. Zero-length means no configuration. |
| U32 hwIsisPrefixPriorityL1TagValue | 1.3.6.1.4.1.2011.5.25.24.2.1.4.1.6 | Unsigned32 | read-create | This object indicates the administrative tag of the Level-1 route preference. |
| U32 hwIsisPrefixPriorityL2TagValue | 1.3.6.1.4.1.2011.5.25.24.2.1.4.1.7 | Unsigned32 | read-create | This object indicates the administrative tag of the Level-2 route preference. |
| hwIsisSummaryTable | 1.3.6.1.4.1.2011.5.25.24.2.1.5 | not-accessible | Set of IP summary addresses to use. | |
| hwIsisSummaryEntry | 1.3.6.1.4.1.2011.5.25.24.2.1.5.1 | not-accessible | Each entry contains one IP summary address. | |
| IP hwIsisSummaryIPIndex | 1.3.6.1.4.1.2011.5.25.24.2.1.5.1.1 | InetAddress | not-accessible | This object indicates the IP address of the summarized route. |
| ADR hwIsisSummaryMaskIndex | 1.3.6.1.4.1.2011.5.25.24.2.1.5.1.2 | InetAddressPrefixLength | not-accessible | This object indicates the subnet mask of the summarized route. |
| T/F hwIsisSummaryAvoidFeedBackEnabled | 1.3.6.1.4.1.2011.5.25.24.2.1.5.1.3 | TruthValue | read-create | This object indicates whether the function of avoiding learning the summarized routes through SPF calculation is enabled: true(1): indicates that the function is enabled. false(2): indicates that the function is disabled. By default, the summarized routes can be learned through SPF calculation. |
| T/F hwIsisSummaryGenNull0RouteEnabled | 1.3.6.1.4.1.2011.5.25.24.2.1.5.1.4 | TruthValue | read-create | This object indicates whether the function of generating Null0 routes during route summarization is enabled: true(1): indicates that the function is enabled. false(2): indicates that the function is disabled. By default, the function of generating Null0 routes during route summarization is disabled. |
| INT hwIsisSummaryLevel | 1.3.6.1.4.1.2011.5.25.24.2.1.5.1.5 | INTEGER | read-create | This object indicates the level of the summarized route: level1(1): indicates Level-1. level2(2): indicates Level-2. level12(3): indicates Level-1-2. |
| U32 hwIsisSummaryTag | 1.3.6.1.4.1.2011.5.25.24.2.1.5.1.6 | Unsigned32 | read-create | This object indicates the administrative tag of the summarized route. |
| ROW hwIsisSummaryStatus | 1.3.6.1.4.1.2011.5.25.24.2.1.5.1.7 | RowStatus | read-create | This object indicates the row status of this table: createAndGo(4): indicates that a row is created. destroy(6): indicates that a row is deleted. |
| hwIsisImportRouteTable | 1.3.6.1.4.1.2011.5.25.24.2.1.6 | not-accessible | Set of import route command. | |
| hwIsisImportRouteEntry | 1.3.6.1.4.1.2011.5.25.24.2.1.6.1 | not-accessible | Entry of import route command. | |
| INT hwIsisImportProtocolIndex | 1.3.6.1.4.1.2011.5.25.24.2.1.6.1.1 | INTEGER | not-accessible | This object indicates the routing protocol of the imported routes: direct(1): indicates direct. static(2): indicates static. rip(3): indicates RIP. ospf(4): indicates OSPF isis(5): indicates IS-IS. bgp(6): For VPN instance, indicates EBGP and IBGP, otherwise indicates EBGP. ospfv3(7): indicates OSPFv3. ripng(8): indicates RIPng. bgpIbgp(9): For VPN instance, this is unusable, otherwise indicates IBGP and EBGP. |
| I32 hwIsisImportProcessIdIndex | 1.3.6.1.4.1.2011.5.25.24.2.1.6.1.2 | Integer32 | not-accessible | Process ID of the route protocols. The range is from 1 to 65535. If the protocol is direct, static or bgp, this value can only be 1. |
| T/F hwIsisImportInheritCostEnabled | 1.3.6.1.4.1.2011.5.25.24.2.1.6.1.3 | TruthValue | read-create | This object indicates whether the original cost of the source route is inherited: true(1): indicates that the original cost of the source route is inherited. false(2): indicates that the original cost of the source route is not inherited. |
| U32 hwIsisImportCost | 1.3.6.1.4.1.2011.5.25.24.2.1.6.1.4 | Unsigned32 | read-create | Cost of the imported routes. If the costStyle of the process is wide or widecompatible, the range of this value is from 0 to 4261412864, else the range of this value is from 0 to 63. 0 means no configuration. |
| INT hwIsisImportCostType | 1.3.6.1.4.1.2011.5.25.24.2.1.6.1.5 | INTEGER | read-create | This object indicates the cost type of the imported external route. This object does not apply to IPv6. internal(1): indicates internal. external(2): indicates external. This node is invalid for IPv6. By default, the cost type of the imported external route is external. |
| INT hwIsisImportLevel | 1.3.6.1.4.1.2011.5.25.24.2.1.6.1.6 | INTEGER | read-create | This object indicates the local IS-IS level of the imported route: level1(1): indicates Level-1. level2(2): indicates Level-2. level12(3): indicates Level-1-2. |
| U32 hwIsisImportTag | 1.3.6.1.4.1.2011.5.25.24.2.1.6.1.7 | Unsigned32 | read-create | This object indicates the administrative tag assigned to an imported route. If this object is not configured, the value will be 0. |
| OCT hwIsisImportPolicyName | 1.3.6.1.4.1.2011.5.25.24.2.1.6.1.8 | OCTET STRING | read-create | This object indicates the name of the routing policy used to import routes. The name is a string of 0 to 40 characters. The length 0 indicates that no name is configured for the routing policy used to import routes. |
| ROW hwIsisImportRouteStatus | 1.3.6.1.4.1.2011.5.25.24.2.1.6.1.9 | RowStatus | read-create | This object indicates the row status of this table: createAndGo(4): indicates that a row is created. destroy(6): indicates that a row is deleted. |
| hwIsisRouteLeakTable | 1.3.6.1.4.1.2011.5.25.24.2.1.7 | not-accessible | Set of route leak commands. | |
| hwIsisRouteLeakEntry | 1.3.6.1.4.1.2011.5.25.24.2.1.7.1 | not-accessible | Entry of route leak commands. | |
| INT hwIsisRouteLeakTypeIndex | 1.3.6.1.4.1.2011.5.25.24.2.1.7.1.1 | INTEGER | not-accessible | This object indicates the index of the route leaking type: level1intolevel2(1): indicates that Level-1 routes are leaked to Level-2. level2intolevel1(2): indicates that Level-2 routes are leaked to Level-1. |
| U32 hwIsisRouteLeakTag | 1.3.6.1.4.1.2011.5.25.24.2.1.7.1.2 | Unsigned32 | read-create | This object indicates the tag of route leaking. If the tag is not configured, the reading value will be 0. |
| INT hwIsisRouteLeakFilterPolicyType | 1.3.6.1.4.1.2011.5.25.24.2.1.7.1.3 | INTEGER | read-create | This object indicates the type of the policy used for route leaking: none(0): indicates that no policy type is specified. basicAcl(1): indicates the number of a basic ACL. aclName(2): indicates the ACL name. ipPrefix(3): indicates the IPv4 prefix. routePolicy(4): indicates the routing policy. |
| I32 hwIsisRouteLeakFilterPolicyBasicAcl | 1.3.6.1.4.1.2011.5.25.24.2.1.7.1.4 | Integer32 | read-create | The value of this object identifies the number of a basic ACL. The value ranges from 2000 to 2999. 0 means no configuration, The range of this value is from 2000 to 2999. |
| OCT hwIsisRouteLeakFilterPolicyPolicyName | 1.3.6.1.4.1.2011.5.25.24.2.1.7.1.5 | OCTET STRING | read-create | The policy name of route leak. If policy type is aclName, the length of this value is from 1 to 32. If policy type is ipPrefix the length of this value is from 1 to 169. If policy type is routePolicy, the length of this value is from 1 to 40. The default length is 0. |
| ROW hwIsisRouteLeakStatus | 1.3.6.1.4.1.2011.5.25.24.2.1.7.1.6 | RowStatus | read-create | This object indicates the row status of this table: createAndGo(4): indicates that a row is created. destroy(6): indicates that a row is deleted. |
| hwIsisFrrTable | 1.3.6.1.4.1.2011.5.25.24.2.1.8 | not-accessible | Set of Frr commands. | |
| hwIsisFrrEntry | 1.3.6.1.4.1.2011.5.25.24.2.1.8.1 | not-accessible | Entry of frr commands for the specific MT of process. | |
| OCT hwIsisFrrPolicyName | 1.3.6.1.4.1.2011.5.25.24.2.1.8.1.1 | OCTET STRING | read-create | The value of this object identifies the FRR policy name. The value is a string of 1 to 40 characters. Value 0 indicates that the FRR policy is deleted. |
| INT hwIsisFrrLoopFreeAltLevel | 1.3.6.1.4.1.2011.5.25.24.2.1.8.1.2 | INTEGER | read-create | The value of this object identifies the level of the FRR LFA algorithm. null(0): cancels the operation of the LFA algorithm. level1(1): indicates Level-1. level2(2): indicates Level-2. level12(3): indicates Level-1-2. |
| T/F hwIsisFrrEnabled | 1.3.6.1.4.1.2011.5.25.24.2.1.8.1.3 | TruthValue | read-create | The value of this object identifies the status of FRR: enable(1): enables FRR. disable(2): disables FRR. By default, FRR is disabled. |
| hwIsisIntfBaseTable | 1.3.6.1.4.1.2011.5.25.24.2.1.21 | not-accessible | Set of commands on interface of the Integrated IS-IS protocol existing on the system. | |
| hwIsisIntfBaseEntry | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1 | not-accessible | Each row defines some commands to a single interface of the IS-IS protocol existing on the system. | |
| U32 hwIsisInterfaceIndex | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.1 | Unsigned32 | not-accessible | The value of this object identifies the interface index. |
| INT hwIsisEnableIPProtocol | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.2 | INTEGER | read-create | The value of this object identifies the status of IPv4 IS-IS on an interface: enable(1): enables IPv4 IS-IS. disable(2): disables IPv4 IS-IS. |
| INT hwIsisEnableIPv6Protocol | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.3 | INTEGER | read-create | The value of this object identifies the status of IPv6 IS-IS on an interface: enable(1): enables IPv6 IS-IS. disable(2): disables IPv6 IS-IS. |
| INT hwIsisCircLevel | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.4 | INTEGER | read-create | The value of this object identifies the level of an interface: level1(1): indicates Level-1. level2(2): indicates Level-2. level12(3): indicates Level-1-2. By default, the interface is at Level-1-2. |
| INT hwIsisCircSimulation | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.5 | INTEGER | read-create | The value of this object identifies whether the broadcast interface is simulated as a P2P interface: enable(1): indicates that the broadcast interface is simulated as a P2P interface. disable(2): indicates that the broadcast interface is not simulated as a P2P interface. By default, broadcast interfaces are not simulated as P2P interfaces. |
| I32 hwIsisCircL1HelloInterval | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.6 | Integer32 | read-create | The value of this object identifies the interval for sending Level-1 Hello PDUs. The value ranges from 3 to 255, in seconds. By default, the value is 10s. |
| I32 hwIsisCircL2HelloInterval | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.7 | Integer32 | read-create | The value of this object identifies the interval for sending Level-2 Hello PDUs. The value ranges from 3 to 255, in seconds. By default, the value is 10s. |
| I32 hwIsisCircL1HelloMultiplier | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.8 | Integer32 | read-create | The value of this object identifies the number of Level-1 Hello PDUs that fail to received from the IS-IS neighbor before the neighbor declared Down. The value ranges from 3 to 1000. By default, the value is 3. |
| I32 hwIsisCircL2HelloMultiplier | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.9 | Integer32 | read-create | The value of this object identifies the number of Level-2 Hello PDUs that fail to received from the IS-IS neighbor before the neighbor declared Down. The value ranges from 3 to 1000. By default, the value is 3. |
| INT hwIsisCircL1AuthMode | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.10 | INTEGER | read-create | The value of this object identifies the mode of authenticating Level-1 Hello PDUs: null(0): indicates that area-based authentication is not configured. md5(1): indicates that the password is encrypted through MD5 and then sent. simple(2): indicates that the password is sent in plaintext. keychain(3): indicates that the key-chain that varies with the time is encrypted through MD5 and then sent. By default, area-based authentication is not configured. |
| OCT hwIsisCircL1AuthText | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.11 | OCTET STRING | read-create | The value of this object identifies the authentication password of Level-1 Hello packets. The password is a string of characters. If the packet authentication mode is simple, the password is a string of 0 to 16 characters. If the packet authentication mode is MD5, the password is a string of 0 to 392 characters. If the packet authentication mode is keychain, the name is a string of 0 to 47 characters. The length 0 indicates that the authentication password of Level-1 Hello packets is not configured. When read, it always returns length 0. |
| INT hwIsisCircL1AuthSendOnly | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.12 | INTEGER | read-create | The value of this object identifies the mode of sending the authentication password of Level-1 Hello PDUs: true(1): indicates that the passwords in only the sent PDUs are authenticated but not in the received PDUs. false(2): indicates that the passwords in both sent and received PDUs are authenticated. By default, the passwords in both sent and received PDUs are authenticated. |
| INT hwIsisCircL1AuthCode | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.13 | INTEGER | read-create | The value of this object identifies the authentication code of Level-1 Hello PDUs: none(0): indicates that no authentication is configured. osi(10): indicates OSI authentication. ip(133): indicates IP authentication. |
| INT hwIsisCircL2AuthMode | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.14 | INTEGER | read-create | The value of this object identifies the mode of authenticating Level-2 Hello PDUs: null(0): indicates that area-based authentication is not configured. md5(1): indicates that password is encrypted through MD5 and then sent. simple(2): indicates that the password is sent in plaintext. keychain(3): indicates that the key-chain that varies with the time is encrypted through MD5 and then sent. By default, area-based authentication is not configured. |
| OCT hwIsisCircL2AuthText | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.15 | OCTET STRING | read-create | The value of this object identifies the authentication password of Level-2 Hello packets. The password is a string of characters. If the packet authentication mode is simple, the password is a string of 0 to 16 characters. If the packet authentication mode is MD5, the password is a string of 0 to 392 characters. If the packet authentication mode is keychain, the name is a string of 0 to 47 characters. The length 0 indicates that the authentication password of Level-2 Hello packets is not configured. When read, it always returns length 0. |
| INT hwIsisCircL2AuthSendOnly | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.16 | INTEGER | read-create | The value of this object identifies the mode of sending the authentication password of Level-2 Hello PDUs: true(1): indicates that the passwords in only the sent PDUs are authenticated but not in the received PDUs. false(2): indicates that the password is authenticated in the PDUs that are both sent and received. By default, the passwords in both sent and received PDUs are authenticated. |
| INT hwIsisCircL2AuthCode | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.17 | INTEGER | read-create | The value of this object identifies the authentication code of Level-2 Hello PDUs: none(0): indicates that no authentication is configured. osi(10): indicates OSI authentication. ip(133): indicates IP authentication. |
| INT hwIsisCircLdpSync | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.18 | INTEGER | read-create | The value of this object identifies the status of synchronization of IS-IS and LDP: enable(1): enables synchronization of IS-IS and LDP. disable(2): disables synchronization of IS-IS and LDP. By default, synchronization of IS-IS and LDP is disabled. |
| I32 hwIsisCircLdpSyncHoldDown | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.19 | Integer32 | read-create | The value of this object identifies the timeout period of the Holddown time for synchronization of IS-IS and LDP. The value ranges from 0 to 65535, in seconds. By default, the value is 10s. 0 means to stop Holddown timer. -1 means no configuration. |
| I32 hwIsisCircLdpHldMaxCost | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.20 | Integer32 | read-create | The value of this object identifies the timeout period of the Hold-Max-Cost time for synchronization of IS-IS and LDP. The value ranges from 0 to 65536, in seconds. By default, the value is 10s. The value of 65536 means infinite. 0 means to stop Hold-Max-Cost timer. -1 means no configuration. |
| INT hwIsisCircSmallHello | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.21 | INTEGER | read-create | The value of this object identifies whether IS-IS sends small Hello PDUs without the padding field: enable(1): indicates that IS-IS sends small Hello PDUs without the padding field. disable(2): indicates that IS-IS does not send small Hello PDUs without the padding field. By default, the function is disabled. |
| INT hwIsisCircIpIgnore | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.22 | INTEGER | read-create | The value of this object identifies whether the segment in an IP address is checked: enable(1): indicates that the segment in an IP address is not checked. disable(2): indicates that the segment in an IP address is checked. By default, the segment in an IP address is checked. This object applies to only P2P interfaces. |
| INT hwIsisCircSenseRpr | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.23 | INTEGER | read-create | The value of this object identifies whether fast RPR loop detection is enabled: enable(1): enables fast RPR loop detection. disable(2): disables fast RPR loop detection. By default, fast RPR loop detection is disabled. |
| INT hwIsisCircPadHello | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.24 | INTEGER | read-create | The value of this object identifies whether IS-IS sends standard Hello PDUs with the padding field: enable(1): indicates that IS-IS sends standard Hello PDUs with the padding field. disable(2): indicates that IS-IS does not send standard Hello PDUs with the padding field. By default, the function is disabled. |
| I32 hwIsisCircLspRetransInterval | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.25 | Integer32 | read-create | The value of this object identifies the interval for resending LSPs. The value ranges from 1 to 300, in seconds. The default value is 5. This object applies to only P2P interfaces. |
| I32 hwIsisL1CsnpTimerValue | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.26 | Integer32 | read-create | The value of this object identifies the interval for sending Level-1 CSNP PDUs on an interface. The value ranges from 1 to 65535, in seconds. The default value is 10. |
| I32 hwIsisL2CsnpTimerValue | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.27 | Integer32 | read-create | The value of this object identifies the interval for sending Level-2 CSNP PDUs on an interface. The value ranges from 1 to 65535, in seconds. The default value is 10. |
| I32 hwIsisLspThrottleInterval | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.28 | Integer32 | read-create | The value of this object identifies the interval for sending batch of LSPs or CSNPs on an interface. The value ranges from 1 to 10000, in milliseconds. By default, the value is 50. |
| I32 hwIsisLspThrottleCount | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.29 | Integer32 | read-create | The value of this object identifies the number of a bundle of LSPs. The value ranges from 1 to 1000. By default, it is 10. |
| I32 hwIsisCircL1DisPriority | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.30 | Integer32 | read-create | The value of this object identifies the priority of the Level-1 DIS, which is valid only on a broadcast interface. The value ranges from 0 to 127. By default, it is 64. |
| I32 hwIsisCircL2DisPriority | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.31 | Integer32 | read-create | The value of this object identifies the priority of the Level-2 DIS, which is valid only on a broadcast interface. The value ranges from 0 to 127. By default, it is 64. |
| INT hwIsisCircSilent | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.32 | INTEGER | read-create | The value of this object identifies whether the status of an IS-IS interface is set to silent. enable(1): indicates that the status of IS-IS interface is set to silent. disable(2): indicates that the status of IS-IS interface is not set to silent. By default, the function is disabled. |
| U32 hwIsisCircMeshGroup | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.33 | Unsigned32 | read-create | The value of this object identifies the mesh-group ID. The value ranges from 0 to 4294967295. Value 0 indicates that the mesh-group ID is not set. |
| INT hwIsisCircMeshBlock | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.34 | INTEGER | read-create | The value of this object identifies the mesh block function. If this function is configured, the set mesh-group ID is deleted. The value of this object can be: enable(1): enables the mesh block function. disable(2): disables the mesh block function. By default, the function is disabled. |
| OCT hwIsisCircDisName | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.35 | OCTET STRING | read-create | The value of this object identifies the DIS name of an interface. The configuration is applicable to only a broadcast interface. The value is a string of 0 to 64 characters. Value 0 indicates that the DIS name is not configured. |
| INT hwIsisCircPppNego | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.36 | INTEGER | read-create | The value of this object identifies the mode of negotiating the setup of a neighbor relationship on P2P interfaces: none(0): indicates that the negotiation mode used to establish a neighbor relationship is not specified. twoWay(1): indicates that a neighbor relationship is set up through negotiations in two-way handshake mode. threeWay(2): indicates that a neighbor relationship is set up through negotiations in three-way handshake mode. threeWayOnly(3): indicates that a neighbor relationship is set up through negotiations in three-way handshake mode and the backward compatibility is not supported. By default, a neighbor relationship is set up through negotiations in three-way handshake mode. |
| INT hwIsisCircPppOsicpCheck | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.37 | INTEGER | read-create | The value of this object identifies whether the OSICP check is required: enable(1): enables the OSICP check. disable(2): disables the OSICP check. By default, the function is disabled. This object applies to only P2P interfaces. |
| ROW hwIsisIntfRowStatus | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.38 | RowStatus | read-create | The value of this object identifies the setting of two values: createAndGo(4): creates one row. destroy(6): deletes one row. |
| OCT hwIsisCircL1AuthKeychainName | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.39 | OCTET STRING | read-create | The value of this object identifies the keychain name of Level-1 Hello packets. The keychain name is a string of characters. The name is a string of 0 to 47 characters. The length 0 indicates that the authentication password of Level-1 Hello packets is not configured. When read, it returns the keychain name. |
| OCT hwIsisCircL2AuthKeychainName | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.40 | OCTET STRING | read-create | The value of this object identifies the keychain name of Level-2 Hello packets. The keychain name is a string of characters. The name is a string of 0 to 47 characters. The length 0 indicates that the authentication password of Level-2 Hello packets is not configured. When read, it returns the keychain name. |
| INT hwIsisCircStrictSnpaCheckEnable | 1.3.6.1.4.1.2011.5.25.24.2.1.21.1.41 | INTEGER | read-create | The value of this object identifies whether the snpa check of lsp and snp is required. enable(1): enables the snpa check. disable(2): disables the snpa check. By default, the function is disabled. This object applies to only simulated P2P interfaces. |
| hwIsisIntfExtTable | 1.3.6.1.4.1.2011.5.25.24.2.1.22 | not-accessible | Set of some specific commands on interface of the Integrated IS-IS protocol existing on the system, which are different of IP type. | |
| hwIsisIntfExtEntry | 1.3.6.1.4.1.2011.5.25.24.2.1.22.1 | not-accessible | Entry of Some specific commands on interface of the Integrated IS-IS protocol existing on the system, which are different of IP type. | |
| I32 hwIsisCircL1Cost | 1.3.6.1.4.1.2011.5.25.24.2.1.22.1.1 | Integer32 | read-create | The value of this object identifies the Level-1 cost of an interface. If the cost style is wide or widecompatible, the range of this value is from 0 to 16777215, else the range of this value is from 0 to 63. The value of 0 means undo this configuration, and the cost of the circuit will become the default value. |
| I32 hwIsisCircL2Cost | 1.3.6.1.4.1.2011.5.25.24.2.1.22.1.2 | Integer32 | read-create | The value of this object identifies the Level-2 cost of an interface. If the cost style is wide or widecompatible, the range of this value is from 0 to 16777215, else the range of this value is from 0 to 63. The value of 0 means undo this configuration, and the cost of the circuit will become the default value. |
| U32 hwIsisL1TagValue | 1.3.6.1.4.1.2011.5.25.24.2.1.22.1.3 | Unsigned32 | read-create | The value of this object identifies the tag value of a Level-1 interface. The value ranges from 0 to 4294967295. By default, it is 0, which indicates that the set tag value is deleted. |
| U32 hwIsisL2TagValue | 1.3.6.1.4.1.2011.5.25.24.2.1.22.1.4 | Unsigned32 | read-create | The value of this object identifies the tag value of a Level-2 interface. The value ranges from 0 to 4294967295. By default, it is 0, which indicates that the set tag value is deleted. |
| INT hwIsisCircSuppReachablity | 1.3.6.1.4.1.2011.5.25.24.2.1.22.1.5 | INTEGER | read-create | The value of this object identifies whether the advertisement of the interface address is suppressed: Null(0): indicates that the interface address can be advertised. level1(1): indicates that the advertisement of the Level-1 interface address is suppressed. level2(2): indicates that the advertisement of the Level-2 interface address is suppressed. level12(3): indicates that the advertisement of the Level-1 and Level-2 interface addresses is suppressed. By default, the interface address can be advertised. |
| INT hwIsisCircFrrBackup | 1.3.6.1.4.1.2011.5.25.24.2.1.22.1.6 | INTEGER | read-create | The value of this object identifies whether an interface is enabled to become a backup interface in Loop Free Alternate (LFA) calculation. Null(0): disables an interface from becoming a backup interface in LFA calculation. level1(1): specifies an interface as a backup interface in Level-1. level2(2): specifies an interface as a backup interface in Level-2. level12(3): specifies an interface as a backup interface in Level-1 and Level-2. |
| ROW hwIsisCircMTRowStatus | 1.3.6.1.4.1.2011.5.25.24.2.1.22.1.7 | RowStatus | read-create | This object indicates the row status of this table: createAndGo(4): indicates that a row is created. destroy(6): indicates that a row is deleted. |
| hwIsisIntfBfdTable | 1.3.6.1.4.1.2011.5.25.24.2.1.23 | not-accessible | Set of BFD commands on interface of the Integrated IS-IS protocol existing on the system. | |
| hwIsisIntfBfdEntry | 1.3.6.1.4.1.2011.5.25.24.2.1.23.1 | not-accessible | Entry of BFD commands on interface of the Integrated IS-IS protocol existing on the system. | |
| INT hwIsisCircBfdState | 1.3.6.1.4.1.2011.5.25.24.2.1.23.1.1 | INTEGER | read-create | The value of this object identifies the BFD status: enable(1): enables BFD. disable(2): disables BFD. static(3): configures static BFD. block(4): blocks BFD on an interface. By default, BFD is not enabled. |
| I32 hwIsisCircBfdMinTxInterval | 1.3.6.1.4.1.2011.5.25.24.2.1.23.1.2 | Integer32 | read-create | The value of this object identifies the minimum interval for sending BFD packets. The value range and default value of this object are determined by the license file. |
| I32 hwIsisCircBfdMinRxInterval | 1.3.6.1.4.1.2011.5.25.24.2.1.23.1.3 | Integer32 | read-create | The value of this object identifies the minimum interval for sending BFD packets. The value range and default value of this object are determined by the license file. |
| I32 hwIsisCircBfdMultiplier | 1.3.6.1.4.1.2011.5.25.24.2.1.23.1.4 | Integer32 | read-create | The value of this object identifies the local BFD detection multiplier. The value range and default value of this object are determined by the license file. |
| INT hwIsisCircBfdFrrBinding | 1.3.6.1.4.1.2011.5.25.24.2.1.23.1.5 | INTEGER | read-create | This object indicates that the BFD status is bound to IS-IS Auto FRR. enable(1): indicates that BFD is bound to IS-IS Auto FRR. disable(2): indicates that BFD is not bound to IS-IS Auto FRR. By default, the BFD session status is not bound to IS-IS Auto FRR. |
| hwIsisTrapsObjects | 1.3.6.1.4.1.2011.5.25.24.2.2 | |||
| INT hwIsisAdjChangeReason | 1.3.6.1.4.1.2011.5.25.24.2.2.1 | INTEGER | accessible-for-notify | Adj down reason |
| I32 hwisisSysInstance | 1.3.6.1.4.1.2011.5.25.24.2.2.2 | Integer32 | accessible-for-notify | The unique identifier of the Integrated IS-IS instance to which this row corresponds. This object follows the index behavior. |
| INT hwisisSysLevelIndex | 1.3.6.1.4.1.2011.5.25.24.2.2.3 | INTEGER | accessible-for-notify | The level that this entry describes. |
| SYS hwIsisOwnSysID | 1.3.6.1.4.1.2011.5.25.24.2.2.4 | SystemID | accessible-for-notify | The ID for this instance of the Integrated IS-IS protocol. This value is appended to each of the area addresses to form the Network Entity Titles. The derivation of a value for this object is implementation-specific. Some implementations may automatically assign values and not permit an SNMP write, while others may require the value to be set manually. |
| SYS hwIsisAdjSysID | 1.3.6.1.4.1.2011.5.25.24.2.2.5 | SystemID | accessible-for-notify | The ID for this instance of the Integrated IS-IS protocol. This value is appended to each of the area addresses to form the Network Entity Titles. The derivation of a value for this object is implementation-specific. Some implementations may automatically assign values and not permit an SNMP write, while others may require the value to be set manually. |
| OCT hwIsisAdjSysName | 1.3.6.1.4.1.2011.5.25.24.2.2.6 | OCTET STRING | accessible-for-notify | Configures the name of the IS-IS dynamic host. The value is a string of 1 to 64 characters. When the length is 0, the configured IS-IS dynamic host name is deleted. |
| SYS hwIsisConflictSystemID | 1.3.6.1.4.1.2011.5.25.24.2.2.7 | SystemID | accessible-for-notify | The ID for this instance of the Integrated IS-IS protocol. This value is appended to each of the area addresses to form the Network Entity Titles. The derivation of a value for this object is implementation-specific. Some implementations may automatically assign values and not permit an SNMP write, while others may require the value to be set manually. |
| SYS hwIsisAutoSysId | 1.3.6.1.4.1.2011.5.25.24.2.2.8 | SystemID | accessible-for-notify | The ID for this instance of the Integrated IS-IS protocol. This value is appended to each of the area addresses to form the Network Entity Titles. The derivation of a value for this object is implementation-specific. Some implementations may automatically assign values and not permit an SNMP write, while others may require the value to be set manually. |
| IP hwIsisLocalIP | 1.3.6.1.4.1.2011.5.25.24.2.2.9 | InetAddress | accessible-for-notify | Local IP address. |
| IP hwIsisRemoteIP | 1.3.6.1.4.1.2011.5.25.24.2.2.10 | InetAddress | accessible-for-notify | IP address of the remote end. |
| IP hwIsisAdjIP | 1.3.6.1.4.1.2011.5.25.24.2.2.11 | InetAddress | accessible-for-notify | Neighbor IP address. |
| hwIsisConfConformance | 1.3.6.1.4.1.2011.5.25.24.2.3 | |||
| hwIsisCompliances | 1.3.6.1.4.1.2011.5.25.24.2.3.1 | |||
| hwIsisModuleFullCompliance | 1.3.6.1.4.1.2011.5.25.24.2.3.1.1 | The compliance statement for entities implementing the Huawei ISIS MIB | ||
| hwIsisConfGroups | 1.3.6.1.4.1.2011.5.25.24.2.3.2 | |||
| hwIsisProcBaseGroup | 1.3.6.1.4.1.2011.5.25.24.2.3.2.1 | The group of hwIsisProcBaseGroup. | ||
| hwIsisProcMTExtGroup | 1.3.6.1.4.1.2011.5.25.24.2.3.2.2 | The group of hwIsisProcMTExtGroup. | ||
| hwIsisPrefixPriorityGroup | 1.3.6.1.4.1.2011.5.25.24.2.3.2.3 | The group of hwIsisPrefixPriorityGroup. | ||
| hwIsisSummaryGroup | 1.3.6.1.4.1.2011.5.25.24.2.3.2.4 | The group of hwIsisSummaryGroup. | ||
| hwIsisNETGroup | 1.3.6.1.4.1.2011.5.25.24.2.3.2.5 | The group of hwIsisNETGroup. | ||
| hwIsisImportRouteGroup | 1.3.6.1.4.1.2011.5.25.24.2.3.2.6 | The group of hwIsisImportRouteGroup. | ||
| hwIsisRouteLeakGroup | 1.3.6.1.4.1.2011.5.25.24.2.3.2.7 | The group of hwIsisRouteLeakGroup. | ||
| hwIsisFrrGroup | 1.3.6.1.4.1.2011.5.25.24.2.3.2.8 | The group of hwIsisFrrGroup. | ||
| hwIsisIntfBaseGroup | 1.3.6.1.4.1.2011.5.25.24.2.3.2.21 | The group of hwIsisIntfBaseGroup. | ||
| hwIsisIntfExtGroup | 1.3.6.1.4.1.2011.5.25.24.2.3.2.22 | The group of hwIsisIntfExtGroup. | ||
| hwIsisIntfBfdGroup | 1.3.6.1.4.1.2011.5.25.24.2.3.2.23 | The group of hwIsisIntfBfdGroup. | ||
| hwIsisTrapsObjectsGroup | 1.3.6.1.4.1.2011.5.25.24.2.3.2.24 | The group of adj change reason. | ||
| hwIsisTrapsGroup | 1.3.6.1.4.1.2011.5.25.24.2.3.2.25 | The collections of notifications sent by an IS. | ||
| hwIsisTraps | 1.3.6.1.4.1.2011.5.25.24.2.4 | |||
| NTF hwIsisSystemIdConflict | 1.3.6.1.4.1.2011.5.25.24.2.4.1 | ISIS system Id conflict. | ||
| NTF hwIsisL1ImportRouteExceedLimit | 1.3.6.1.4.1.2011.5.25.24.2.4.2 | ISIS level-1 number of imported routes has exceeded the maximum limit. | ||
| NTF hwIsisL1ImportRouteRestoreToLimit | 1.3.6.1.4.1.2011.5.25.24.2.4.3 | ISIS level-1 number of imported routes is restored to less than or equal to the maximum limit. | ||
| NTF hwIsisL2ImportRouteExceedLimit | 1.3.6.1.4.1.2011.5.25.24.2.4.4 | ISIS level-2 number of imported routes has exceeded the maximum limit. | ||
| NTF hwIsisL2ImportRouteRestoreToLimit | 1.3.6.1.4.1.2011.5.25.24.2.4.5 | ISIS level-2 number of imported routes is restored to less than or equal to the maximum limit. | ||
| NTF hwIsisL1ImportRouteThresholdReach | 1.3.6.1.4.1.2011.5.25.24.2.4.6 | ISIS level-1 number of imported routes has reached the threshold value. | ||
| NTF hwIsisL1ImportRouteThresholdReachClear | 1.3.6.1.4.1.2011.5.25.24.2.4.7 | ISIS level-1 number of imported routes has been less than the threshold value. | ||
| NTF hwIsisL2ImportRouteThresholdReach | 1.3.6.1.4.1.2011.5.25.24.2.4.8 | ISIS level-2 number of imported routes has reached the threshold value. | ||
| NTF hwIsisL2ImportRouteThresholdReachClear | 1.3.6.1.4.1.2011.5.25.24.2.4.9 | ISIS level-2 number of imported routes has been less than the threshold value. | ||
| NTF hwIsisLsdbThresholdReach | 1.3.6.1.4.1.2011.5.25.24.2.4.10 | The number of LSP has reached the upper threshold value. | ||
| NTF hwIsisLsdbThresholdReachClear | 1.3.6.1.4.1.2011.5.25.24.2.4.11 | The number of LSP has been less than the lower threshold value. | ||
| NTF hwIsisSystemIdAutoRecover | 1.3.6.1.4.1.2011.5.25.24.2.4.12 | After a system ID conflict was detected within an IS-IS area, IS-IS changed the system ID automatically. | ||
| NTF hwIsisAdjacencyChangeClear | 1.3.6.1.4.1.2011.5.25.24.2.4.13 | The isisAdjacencyChange alarm was cleared. | ||
| NTF hwIsisSeqNumExceedThreshold | 1.3.6.1.4.1.2011.5.25.24.2.4.14 | The LSP sequence number has exceeded the upper threshold value. |
RFC description
Huawei IS-IS routing protocol configuration MIB containing objects for ISIS processes and peripheral devices.
Start monitoring Huawei router or switch running IS-IS (conformance/compliance module) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.