All MIBs › HLS-MIB
Category: Domain: Network Management
Description: High-level service (HLS) MIB providing service-level monitoring and management objects for network services.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is HLS-MIB?
HLS-MIB is a generically-named module for High-Level Service management, intended to expose service-level monitoring and management objects for network services layered above basic device connectivity. Without vendor context or a module description, its exact scope is unclear, but modules of this class typically expose service status, service-level configuration, and associated performance or fault indicators. Its likely use is monitoring the operational state of a defined "service" abstraction (up/down, degraded, configuration parameters) rather than raw hardware sensors. It would likely depend on lower-layer MIBs (interfaces, IP) to map services onto physical resources, though this cannot be confirmed without more detail. Deployment context would be a network management system tracking service-level rather than device-level health, drawing on the generic HLS-MIB MIB framework described above.
IPNetwork Monitor allows you to monitor SNMP objects defined in HLS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- vendor-neutral, standards-based MIB, not tied to a specific manufacturer
- generic network service management platforms
Monitoring Examples
Given the absence of sample objects and module description text, no concrete object names can be cited for this MIB; a typical scenario would involve polling a service-status table to detect when a defined high-level service transitions from active to degraded or down, but this is inferred from the module's naming rather than grounded in specific objects.
What Can Be Monitored
- service operational status
- service configuration parameters
This MIB depends on
Related MIBs
Imported Objects
From RFC1155-SMI
| Counter | |
| IpAddress | |
| TimeTicks | |
| enterprises |
From RFC1213-MIB
| DisplayString |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| hls | 1.3.6.1.4.1.26 | |||
| hlsBridges | 1.3.6.1.4.1.26.2 | |||
| ethernetBridge | 1.3.6.1.4.1.26.2.1 | |||
| ramAddrTab8000Tab | 1.3.6.1.4.1.26.2.1.1 | not-accessible | The RAM-resident Address Table in an HLS non-Token-Bus Bridge. | |
| OCT ramAddrTab8000Entry | 1.3.6.1.4.1.26.2.1.1.1 | OCTET STRING | read-write | An instance of this object-type exists for each entry in the RAM-resident Address Table in a HLS non-Token-Bus Bridge. The format of the OCTET STRING is: 1st octet: 1 = Static flag set 0 = Static flag not set 2nd octet: 1 = Restrict flag set 0 = Restrict flag not set 3rd octet: 1 = Origin flag set 0 = Origin flag not set 4th octet: 0 = Bridge's own address 1 = Address on Channel 0 2 = Address on Channel 1 3 = Address is global (i.e. on all Channels) Setting an instance of this object-type to a value of ASN.1 type NULL, causes the identified entry in the RAM-resident Address Table to be deleted. |
| MAC ramAddrTab8000Address | 1.3.6.1.4.1.26.2.1.1.2 | MacAddress | not-accessible | The MAC address associated with this entry |
| OCT ramAddrTab8000Filter | 1.3.6.1.4.1.26.2.1.2 | OCTET STRING | read-write | Setting this value causes the re-creation of the filtered subset (see the object ramAddrTab8000FilterEntry) of the RAM-resident Address Table in a HLS 80xx Bridge. The filtered subset consists of all entries which matched the filter value at the time of the last write to this object. The format of the OCTET STRING is: 1st octet: 0 - must not have Static flag set 1 - must have Static flag set 2 - don't care whether Static flag set 2nd octet: 0 - must not have Restrict flag set 1 - must have Restrict flag set 2 - don't care whether Restrict flag set 3rd octet: 0 - must not have Origin flag set 1 - must have Origin flag set 2 - don't care whether Origin flag set 4th octet: 1 - Address must be on channel 0 (only) 2 - Address must be on channel 1 (only) 3 - Address must be global (channels 0 AND 1) 4 - Address must not be only on channel 0 5 - Address must not be only on channel 1 6 - Address must not be global 7 - Address can be on any channels |
| INT ramAddrTab8000FilterNum | 1.3.6.1.4.1.26.2.1.3 | INTEGER | read-only | The current number of entries in the filtered subset of entries in the RAM-resident Address Table in a HLS 80xx Bridge. The filtered subset consists of allentries which matched the filter value at the time ofthe last write to the object: ramAddrTab8000Filter. |
| ramAddrTab8000FilterTab | 1.3.6.1.4.1.26.2.1.4 | not-accessible | This table contains the filtered subset of the RAM-resident Address Table in a HLS 80xx Bridge. The filtered subset consists of all entries which matched the filter value at the time of the last write to the object: ramAddrTab8000Filter. Note that the contents of this table are constant between writes to ramAddrTab8000Filter. | |
| OCT ramAddrTab8000FilterEntry | 1.3.6.1.4.1.26.2.1.4.1 | OCTET STRING | read-only | An instance of this object-type exists for each entry in the filtered subset of entries in the RAM-resident Address Table in a HLS 80xx Bridge. The filtered subset consists of a copy of those entries in ramAddrTab8000Tab which matched the filter value at the time of the last write to the object: ramAddrTab8000Filter. The format of the OCTET STRING is: octets 1-6: the MAC address of this entry 7th octet: 1 = Static flag set 0 = Static flag not set 8th octet: 1 = Restrict flag set 0 = Restrict flag not set 9th octet: 1 = Origin flag set 0 = Origin flag not set 10th octet: 0 = Bridge's own address 1 = Address on Channel 0 2 = Address on Channel 1 3 = Address is global (i.e. on all Channels) |
| INT ramAddrTab8000FilterIndex | 1.3.6.1.4.1.26.2.1.4.2 | INTEGER | not-accessible | For the i-th entry, this object takes the value i. |
| OCT ramAddrTab8000Delete | 1.3.6.1.4.1.26.2.1.5 | OCTET STRING | write-only | Setting this object to a value causes the immediate deletion of a subset of the entries in the RAM-resident Address Table in a HLS 80xx Bridge. The subset of entries to be deleted is selected by using the value (to which this object is set) as a filter against which all entries are matched, with all entries matching the filter being deleted. The format of the OCTET STRING is: 1st octet: 0 - must not have Static flag set 1 - must have Static flag set 2 - don't care whether Static flag set 2nd octet: 0 - must not have Restrict flag set 1 - must have Restrict flag set 2 - don't care whether Restrict flag set 3rd octet: 0 - must not have Origin flag set 1 - must have Origin flag set 2 - don't care whether Origin flag set 4th octet: 1 - Address must be on channel 0 (only) 2 - Address must be on channel 1 (only) 3 - Address must be global (channels 0 AND 1) 4 - Address must not be only on channel 0 5 - Address must not be only on channel 1 6 - Address must not be global 7 - Address can be on any channels |
| nvramAddrTab8000Tab | 1.3.6.1.4.1.26.2.1.6 | not-accessible | The Address Table stored in Non-Volatile RAM in a HLS 80xx Bridge. | |
| OCT nvramAddrTab8000Entry | 1.3.6.1.4.1.26.2.1.6.1 | OCTET STRING | read-write | An instance of this object-type exists for each entry in the Address Table stored in Non-Volatile RAM in a HLS 80xx Bridge. The format of the OCTET STRING is: 1st octet: 1 = Static flag set 0 = Static flag not set 2nd octet: 1 = Restrict flag set 0 = Restrict flag not set 3rd octet: 1 = Origin flag set 0 = Origin flag not set 4th octet: 0 = Bridge's own address 1 = Address on Channel 0 2 = Address on Channel 1 3 = Address is global (i.e. on all Channels) Setting an instance of this object-type to a value of ASN.1 type NULL, causes the identified entry in the Address Table in Non-Volatile RAM to be deleted. |
| MAC nvramAddrTab8000Address | 1.3.6.1.4.1.26.2.1.6.2 | MacAddress | not-accessible | The MAC address associated with this entry |
| OCT nvramAddrTab8000Filter | 1.3.6.1.4.1.26.2.1.7 | OCTET STRING | read-write | Setting this value causes the re-creation of the filtered subset (see the object nvramAddrTab8000FilterEntry) of the Address Table stored in Non-Volatile RAM in a HLS Local/Remote Bridge. The filtered subset consists of all entries which matched the filter value at the time of the last write to this object. The format of the OCTET STRING is: 1st octet: 0 - must not have Static flag set 1 - must have Static flag set 2 - don't care whether Static flag set 2nd octet: 0 - must not have Restrict flag set 1 - must have Restrict flag set 2 - don't care whether Restrict flag set 3rd octet: 0 - must not have Origin flag set 1 - must have Origin flag set 2 - don't care whether Origin flag set 4th octet: 1 - Address must be on channel 0 (only) 2 - Address must be on channel 1 (only) 3 - Address must be global (channels 0 AND 1) 4 - Address must not be only on channel 0 5 - Address must not be only on channel 1 6 - Address must not be global 7 - Address can be on any channels |
| INT nvramAddrTab8000FilterNum | 1.3.6.1.4.1.26.2.1.8 | INTEGER | read-only | The current number of entries in the filtered subset of entries in the Address Table in Non-Volatile RAM in a HLS Local/Remote Bridge. The filtered subset consists of all entries which matched the filter value at the time of the last write to the object: nvramAddrTab8000Filter. |
| nvramAddrTab8000FilterTab | 1.3.6.1.4.1.26.2.1.9 | not-accessible | This table contains the filtered subset of the Address Table in Non-Volatile RAM in a HLS Local/Remote Bridge. The filtered subset consists of all entries which matched the filter value at the time it was last written to the object: nvramAddrTab8000Filter. Note that the contents of this table are constant between writes to nvramAddrTab8000Filter. | |
| OCT nvramAddrTab8000FilterEntry | 1.3.6.1.4.1.26.2.1.9.1 | OCTET STRING | read-only | An instance of this object-type exists for each entry within the filtered subset of the Address Table in Non-Volatile RAM in a HLS Local/Remote Bridge. The filtered subset consists of all entries which matched the filter value at the time of the last write to the object: nvramAddrTab8000Filter. The format of the OCTET STRING is: octets 1-6: the MAC address of this entry 7th octet: 1 = Static flag set 0 = Static flag not set 8th octet: 1 = Restrict flag set 0 = Restrict flag not set 9th octet: 1 = Origin flag set 0 = Origin flag not set 10th octet: 0 = Bridge's own address 1 = Address on Channel 0 2 = Address on Channel 1 3 = Address is global (i.e. on all Channels) |
| INT nvramAddrTab8000FilterIndex | 1.3.6.1.4.1.26.2.1.9.2 | INTEGER | not-accessible | For the i-th entry, this object has the value i. |
| OCT nvramAddrTab8000Delete | 1.3.6.1.4.1.26.2.1.10 | OCTET STRING | write-only | Setting this object to a value causes the immediate deletion of a subset of the entries in the Address Table in Non-Volatile RAM in a HLS Local/Remote Bridge. The subset of entries to be deleted is selected by using the value (to which this object is set) as a filter against which all entries are matched, with all entries matching the filter being deleted. The format of the OCTET STRING is: 1st octet: 0 - must not have Static flag set 1 - must have Static flag set 2 - don't care whether Static flag set 2nd octet: 0 - must not have Restrict flag set 1 - must have Restrict flag set 2 - don't care whether Restrict flag set 3rd octet: 0 - must not have Origin flag set 1 - must have Origin flag set 2 - don't care whether Origin flag set 4th octet: 1 - Address must be on channel 0 (only) 2 - Address must be on channel 1 (only) 3 - Address must be global (channels 0 AND 1) 4 - Address must not be only on channel 0 5 - Address must not be only on channel 1 6 - Address must not be global 7 - Address can be on any channels |
| OCT nvramAddrTab8000Update | 1.3.6.1.4.1.26.2.1.11 | OCTET STRING | write-only | Setting this object to a value causes an update of the Address Table in Non-Volatile RAM in a HLS Local/Remote Bridge. This update is the combination of the deletion of all existing entries in Non-Volatile RAM table, followed by the addition of a set of new entries. The set of new entries is a subset of the current entries in the bridge's RAM-resident Address Table. That subset is selected by using the value (to which this object is set) as a filter against which all entries in the RAM-resident Address Table are matched. After the update is completed, the Address Table in Non-Volatile RAM consists of exactly those entries in the RAM-resident Address Table which match with the filter value. The format of the OCTET STRING is: 1st octet: 0 - must not have Static flag set 1 - must have Static flag set 2 - don't care whether Static flag set 2nd octet: 0 - must not have Restrict flag set 1 - must have Restrict flag set 2 - don't care whether Restrict flag set 3rd octet: 0 - must not have Origin flag set 1 - must have Origin flag set 2 - don't care whether Origin flag set 4th octet: 1 - Address must be on channel 0 (only) 2 - Address must be on channel 1 (only) 3 - Address must be global (channels 0 AND 1) 4 - Address must not be only on channel 0 5 - Address must not be only on channel 1 6 - Address must not be global 7 - Address can be on any channels |
| remoteEthernetBridge | 1.3.6.1.4.1.26.2.2 | |||
| INT segmentBlocking | 1.3.6.1.4.1.26.2.2.1 | INTEGER | read-write | The value of this object is a single octet specifying which address space segments are to be blocked/passed by the bridge (for the purpose of load-sharing between bridges). Each address space segment corresponds to one bit in the octet; the first segment corresponds to the least significant bit, the second segment with the second leastsignificant bit; etc. A bit is set to 1 if the corresponding segment is to be blocked. |
| INT linktype | 1.3.6.1.4.1.26.2.2.2 | INTEGER | read-only | The type of physical interface being used on the serial interface to the remote bridge. |
| INT linkSaver | 1.3.6.1.4.1.26.2.2.3 | INTEGER | read-write | The setting of this object controls the use of data compression over the serial link between two bridges. If set to removePadding(1), then any padding for LAN transmission is not transmitted over the serial link. Such padding is required on a LAN when a packet is shorter than a minimum-sized frame. |
| INT crcType | 1.3.6.1.4.1.26.2.2.4 | INTEGER | read-write | The type of CRC used on the serial link between two bridges. Setting this object does not take effect until the next reset of the bridge. When read, the object retruns the last value written to it (which is not necessarily the value of the CRC type being used). |
| INT linkEncoding | 1.3.6.1.4.1.26.2.2.5 | INTEGER | read-write | The encoding scheme used on the serial link between two bridges. Setting this object does not take effect until the next reset of the bridge. When read, the object retruns the last value written to it (which is not necessarily the value of the link encoding being used). |
| tokenBusBridge | 1.3.6.1.4.1.26.2.3 | |||
| INT tbTransmitLevel | 1.3.6.1.4.1.26.2.3.2 | INTEGER | read-write | The transmit level used on the bridge's token bus interface. There are sixteen valid transmit levels which occur at 1.5 dBmV intervals in the range 30.5 dBmV through 53.0 dBmV. The value of this object is the number of 1.5 dBmV intervals greater than 30.5 dBmV. Use of the new transmit level after a write, occurs after the next reset. |
| INT tbSlotTime | 1.3.6.1.4.1.26.2.3.3 | INTEGER | read-write | The slot time for the bridge's token bus interface, in octet-time (i.e. 0.8 microsecond) units. |
| INT tbHoldtime | 1.3.6.1.4.1.26.2.3.4 | INTEGER | read-write | The high priority token hold time, in octet-time (i.e. 0.8 microsecond) units. |
| INT tbRotationTime | 1.3.6.1.4.1.26.2.3.5 | INTEGER | read-write | The maximum ring maintenance rotation time, in octet-time (i.e. 0.8 microsecond) units. |
| INT tbRingTimerInitialValue | 1.3.6.1.4.1.26.2.3.6 | INTEGER | read-only | The initial value to be assigned to the ring maintenance timer, in octet-time (i.e. 0.8 microsecond) units. |
| INT tbSolicitCount | 1.3.6.1.4.1.26.2.3.7 | INTEGER | read-write | The maximum inter-solicit interval, in units of token possessions (i.e. token rotations). |
| INT tbResetDefault | 1.3.6.1.4.1.26.2.3.8 | INTEGER | write-only | Writing a value of resetParms(1) to this object causes the token bus interface parameters to be reset to their default values. |
| INT tbFrequency | 1.3.6.1.4.1.26.2.3.9 | INTEGER | read-write | The frequency ranges used by the interface. Use of the new frequency after a write, occurs after the next reset. |
| ramAddrTab8200Tab | 1.3.6.1.4.1.26.2.3.10 | not-accessible | The RAM-resident Address Table in an HLS Backbone Bridge. | |
| OCT ramAddrTab8200Entry | 1.3.6.1.4.1.26.2.3.10.1 | OCTET STRING | read-write | An instance of this object-type exists for each entry in the RAM-resident Address Table in a HLS Backbone Bridge. The format of the OCTET STRING is: 1st octet: 1 = a Static entry 0 = not a Static entry 2nd octet: 1 = a Restrict entry 0 = not a Restrict entry 3rd octet: 1 = an Origin entry 0 = not an Origin entry 4th octet: 0 = Bridge's own address 1 = Address on Channel 0 2 = Address on Channel 1 3 = Address is global (i.e. on all Channels) octets 5-10: the MAC address of the 8200 bridge to which packets for the entry's MAC address should be forwarded. Setting an instance of this object-type to a value of ASN.1 type NULL, causes the identified entry in the RAM-resident Address Table to be deleted. |
| MAC ramAddrTab8200Address | 1.3.6.1.4.1.26.2.3.10.2 | MacAddress | not-accessible | The MAC address associated with this entry |
| OCT ramAddrTab8200Filter | 1.3.6.1.4.1.26.2.3.11 | OCTET STRING | read-write | Setting this value causes the re-creation of the filtered subset (see the object ramAddrTab8200FilterEntry) of the RAM-resident Address Table in a HLS Backbone Bridge. The filtered subset consists of all entries which matched the filter value at the time of the last write to this object. The format of the OCTET STRING is: 1st octet: 0 - must not be a Static entry 1 - must be a Static entry 2 - don't care whether Static entry or not 2nd octet: 0 - must not be a Restrict entry 1 - must be a Restrict entry 2 - don't care whether Restrict entry or not 3rd octet: 0 - must not be an Origin entry 1 - must be an Origin entry 2 - don't care whether Origin entry or not 4th octet: 1 - Address must be on channel 0 (only) 2 - Address must be on channel 1 (only) 3 - Address must be global (channels 0 AND 1) 4 - Address must not be only on channel 0 5 - Address must not be only on channel 1 6 - Address must not be global 7 - Address can be on any channels octets 5-10: If these octets contain all-ones, then theymatch any entry; otherwise, an entry matchesonly if the value of these 6 octets equalsthe MAC address of the 8200 bridge to which packets for the entry's MAC address should be forwarded. |
| INT ramAddrTab8200FilterNum | 1.3.6.1.4.1.26.2.3.12 | INTEGER | read-only | The current number of entries in the filtered subset of entries in the RAM-resident Address Table in a HLS Backbone Bridge. The filtered subset consists of all entries which matched the filter value at the time of the last write to the object: ramAddrTab8200Filter. |
| ramAddrTab8200FilterTab | 1.3.6.1.4.1.26.2.3.13 | not-accessible | This table contains the filtered subset of the RAM-resident Address Table in a HLS Backbone Bridge. The filtered subset consists of all entries which matched the filter value at the time of the last write to the object: ramAddrTab8200Filter. Note that the contents of this table are constant between writes to ramAddrTab8200Filter. | |
| OCT ramAddrTab8200FilterEntry | 1.3.6.1.4.1.26.2.3.13.1 | OCTET STRING | read-only | An instance of this object-type exists for each entry in the filtered subset of entries in the RAM-resident Address Table in a HLS Backbone Bridge. The filtered subset consists of a copy of those entries in ramAddrTab8200Tab which matched the filter value at the time of the last write to the object: ramAddrTab8200Filter. The format of the OCTET STRING is: octets 1-6: the MAC address of this entry 7th octet: 1 = a Static entry 0 = not a Static entry 8th octet: 1 = a Restrict entry 0 = not a Restrict entry 9th octet: 1 = an Origin entry 0 = not an Origin entry 10th octet: 0 = Bridge's own address 1 = Address on Channel 0 2 = Address on Channel 1 3 = Address is global (i.e. on all Channels) octets 11-16: the MAC address of the 8200 bridge to which packets for the entry's MAC address should be forwarded. |
| INT ramAddrTab8200FilterIndex | 1.3.6.1.4.1.26.2.3.13.2 | INTEGER | not-accessible | For the i-th entry, this object has the value i. |
| OCT ramAddrTab8200Delete | 1.3.6.1.4.1.26.2.3.14 | OCTET STRING | write-only | Setting this object to a value causes the immediate deletion of a subset of the entries in the RAM-resident Address Table in a HLS Backbone Bridge. The subset of entries to be deleted is selected by using the value (to which this object is set) as a filter against which all entries are matched, with all entries matching the filter being deleted. The format of the OCTET STRING is: 1st octet: 0 - must not be a Static entry 1 - must be a Static entry 2 - don't care whether Static entry or not 2nd octet: 0 - must not be a Restrict entry 1 - must be a Restrict entry 2 - don't care whether Restrict entry or not 3rd octet: 0 - must not be an Origin entry 1 - must be an Origin entry 2 - don't care whether Origin entry or not 4th octet: 1 - Address must be on channel 0 (only) 2 - Address must be on channel 1 (only) 3 - Address must be global (channels 0 AND 1) 4 - Address must not be only on channel 0 5 - Address must not be only on channel 1 6 - Address must not be global 7 - Address can be on any channels octets 5-10: If these octets contain all-ones, then they match any entry; otherwise, an entry matches only if the value of these 6 octets equals the MAC address of the 8200 bridge to which packets for the entry's MAC address should be forwarded. |
| nvramAddrTab8200Tab | 1.3.6.1.4.1.26.2.3.15 | not-accessible | The Address Table in Non-Volatile RAM in a HLS Backbone Bridge. | |
| OCT nvramAddrTab8200Entry | 1.3.6.1.4.1.26.2.3.15.1 | OCTET STRING | read-write | An instance of this object-type exists for each entry in the Address Table in Non-Volatile RAM in a HLS Backbone Bridge. The format of the OCTET STRING is: 1st octet: 1 = a Static entry 0 = not a Static entry 2nd octet: 1 = a Restrict entry 0 = not a Restrict entry 3rd octet: 1 = an Origin entry 0 = not an Origin entry 4th octet: 0 = Bridge's own address 1 = Address on Channel 0 2 = Address on Channel 1 3 = Address is global (i.e. on all Channels) octets 5-10: the MAC address of the 8200 bridge to which packets for the entry's MAC address should be forwarded. Setting an instance of this object-type to a value of ASN.1 type NULL, causes the identified entry in the Address Table in Non-Volatile RAM to be deleted. |
| MAC nvramAddrTab8200Address | 1.3.6.1.4.1.26.2.3.15.2 | MacAddress | not-accessible | The MAC address associated with this entry |
| OCT nvramAddrTab8200Filter | 1.3.6.1.4.1.26.2.3.16 | OCTET STRING | read-write | Setting this value causes the re-creation of the filtered subset (see the object nvramAddrTab8200FilterEntry) of the Address Table in Non-Volatile RAM in a HLS Backbone Bridge. The filtered subset consists of all entries which matched the filter value at the time of the last write to this object. The format of the OCTET STRING is: 1st octet: 0 - must not be a Static entry 1 - must be a Static entry 2 - don't care whether Static entry or not 2nd octet: 0 - must not be a Restrict entry 1 - must be a Restrict entry 2 - don't care whether Restrict entry or not 3rd octet: 0 - must not be an Origin entry 1 - must be an Origin entry 2 - don't care whether Origin entry or not 4th octet: 1 - Address must be on channel 0 (only) 2 - Address must be on channel 1 (only) 3 - Address must be global (channels 0 AND 1) 4 - Address must not be only on channel 0 5 - Address must not be only on channel 1 6 - Address must not be global 7 - Address can be on any channels octets 5-10: If these octets contain all-ones, then they match any entry; otherwise, an entry matches only if the value of these 6 octets equals the MAC address of the 8200 bridge to which packets for the entry's MAC address should be forwarded. |
| INT nvramAddrTab8200FilterNum | 1.3.6.1.4.1.26.2.3.17 | INTEGER | read-only | The current number of entries in the filtered subset of entries in the Address Table in Non-Volatile RAM in a HLS Backbone Bridge. The filtered subset consists of all entries which matched the filter value at the time of the last write to the object: nvramAddrTab8200Filter. |
| nvramAddrTab8200FilterTab | 1.3.6.1.4.1.26.2.3.18 | not-accessible | This table contains the filtered subset of entries in the Address Table in Non-Volatile RAM in a HLS Backbone Bridge. The filtered subset consists of all entries which matched the filter value at the time it was last written to the object: nvramAddrTab8200Filter. Note that the contents of this table are constant between writes to nvramAddrTab8200Filter. | |
| OCT nvramAddrTab8200FilterEntry | 1.3.6.1.4.1.26.2.3.18.1 | OCTET STRING | read-only | An instance of this object-type exists for each entry within the filtered subset of the Address Table in Non-Volatile RAM in a HLS Backbone Bridge. The filtered subset consists of all entries which matched the filter value at the time of the last write to the object: nvramAddrTab8200Filter. The format of the OCTET STRING is: octets 1-6: the MAC address of this entry 7th octet: 1 = a Static entry 0 = not a Static entry 8th octet: 1 = a Restrict entry 0 = not a Restrict entry 9th octet: 1 = an Origin entry 0 = not an Origin entry 10th octet: 0 = Bridge's own address 1 = Address on Channel 0 2 = Address on Channel 1 3 = Address is global (i.e. on all Channels) octets 11-16: the MAC address of the 8200 bridge to which packets for the entry's MAC address should be forwarded. |
| INT nvramAddrTab8200FilterIndex | 1.3.6.1.4.1.26.2.3.18.2 | INTEGER | not-accessible | For the i-th entry, this object has the value i. |
| OCT nvramAddrTab8200Delete | 1.3.6.1.4.1.26.2.3.19 | OCTET STRING | write-only | Setting this object to a value causes the immediate deletion of a subset of the entries in the Address Table in Non-Volatile RAM in a HLS 8200 Bridge. The subset of entries to be deleted is selected by using the value (to which this object is set) as a filter against which all entries are matched, with all entries matching the filter being deleted. The format of the OCTET STRING is: 1st octet: 0 - must not be a Static entry 1 - must be a Static entry 2 - don't care whether Static entry or not 2nd octet: 0 - must not be a Restrict entry 1 - must be a Restrict entry 2 - don't care whether Restrict entry or not 3rd octet: 0 - must not be an Origin entry 1 - must be an Origin entry 2 - don't care whether Origin entry or not 4th octet: 1 - Address must be on channel 0 (only) 2 - Address must be on channel 1 (only) 3 - Address must be global (channels 0 AND 1) 4 - Address must not be only on channel 0 5 - Address must not be only on channel 1 6 - Address must not be global 7 - Address can be on any channels octets 5-10: If these octets contain all-ones, then they match any entry; otherwise, an entry matches only if the value of these 6 octets equals the MAC address of the 8200 bridge to which packets for the entry's MAC address should be forwarded. |
| OCT nvramAddrTab8200Update | 1.3.6.1.4.1.26.2.3.20 | OCTET STRING | write-only | Setting this object to a value causes an update of the Address Table in Non-Volatile RAM in a HLS Backbone Bridge. This update is the combination of the deletion of all existing entries in Non-Volatile RAM table, followed by the addition of a set of new entries. The set of new entries is a subset of the current entries in the bridge's RAM-resident Address Table. That subset is selected by using the value (to which this object is set) as a filter against which all entries in the RAM-resident Address Table are matched. After the update is completed, the Address Table in Non-Volatile RAM consists of exactly those entries in the RAM-resident Address Table which match with the filter value. The format of the OCTET STRING is: 1st octet: 0 - must not be a Static entry 1 - must be a Static entry 2 - don't care whether Static entry or not 2nd octet: 0 - must not be a Restrict entry 1 - must be a Restrict entry 2 - don't care whether Restrict entry or not 3rd octet: 0 - must not be an Origin entry 1 - must be an Origin entry 2 - don't care whether Origin entry or not 4th octet: 1 - Address must be on channel 0 (only) 2 - Address must be on channel 1 (only) 3 - Address must be global (channels 0 AND 1) 4 - Address must not be only on channel 0 5 - Address must not be only on channel 1 6 - Address must not be global 7 - Address can be on any channels octets 5-10: If these octets contain all-ones, then they match any entry; otherwise, an entry matches only if the value of these 6 octets equalsthe MAC address of the 8200 bridge to which packets for the entry's MAC address should be forwarded. |
| CTR tbEbitErrors | 1.3.6.1.4.1.26.2.3.21 | Counter | read-only | The number of 802.4 frames received which had the Error-bit set in the trailer. |
| CTR tbFrameFrags | 1.3.6.1.4.1.26.2.3.22 | Counter | read-only | The number of 802.4 frames received which did not have a valid End delimiter. |
| CTR tbTokenPassFails | 1.3.6.1.4.1.26.2.3.23 | Counter | read-only | The number of times this station re-transmitted the token to its neighbor because the neighbor failed to transmit within the required time interval. |
| INT bridgeModel | 1.3.6.1.4.1.26.2.4 | INTEGER | read-only | The HLS model number of the bridge. |
| INT bridgeMode | 1.3.6.1.4.1.26.2.15 | INTEGER | read-write | The current mode of the bridge. |
| INT ageingOption | 1.3.6.1.4.1.26.2.16 | INTEGER | read-write | The status of the Ageing option in the bridge. |
| channelTable | 1.3.6.1.4.1.26.2.17 | not-accessible | The table of per-channel attributes. | |
| channelEntry | 1.3.6.1.4.1.26.2.17.1 | not-accessible | A channel entry containing attributes applicable to a particular channel. | |
| INT chLearnMode | 1.3.6.1.4.1.26.2.17.1.1 | INTEGER | read-write | The status of learning mode for this channel. |
| INT chRestrictMode | 1.3.6.1.4.1.26.2.17.1.2 | INTEGER | read-only | The status of Restrict mode for this channel. A channel's Restrict mode must be enabled in order for the channel to have filtering by destination address enabled for any address. |
| INT chOriginMode | 1.3.6.1.4.1.26.2.17.1.3 | INTEGER | read-write | The status of the Origin mode for this channel. A channel's Origin mode must be enabled in order for the channel to have filtering of non-unicast destination addresses enabled for any individual source addresses. |
| INT chGroupFwdMode | 1.3.6.1.4.1.26.2.17.1.4 | INTEGER | read-write | The value of this object determines whether frames destined for unknown group addresses (i.e. multicast addresses which have not been statically configured) are to be forwarded on this channel. |
| INT chIndFwdMode | 1.3.6.1.4.1.26.2.17.1.5 | INTEGER | read-write | The value of this object determines whether frames destined for unknown individual addresses (i.e. unicast addresses which are not present in the bridge's forwarding tables) are to be forwarded on this channel. |
| INT chDefRestrictFlag | 1.3.6.1.4.1.26.2.17.1.6 | INTEGER | read-write | The value to which the Restrict flag is set for subsequently (re-)learnt addresses on this channel. When Restrict mode is enabled, frames to adestination address which has the Restrict flag set are not forwarded. |
| INT chDefStaticFlag | 1.3.6.1.4.1.26.2.17.1.7 | INTEGER | read-write | The value to which the Static flag is set for subsequently learnt addresses on this channel. Addresses with the Static flag set do not age. |
| INT chDefOriginFlag | 1.3.6.1.4.1.26.2.17.1.8 | INTEGER | read-write | The value to which the Origin flag is set for subsequently (re-)learnt addresses on this channel. When Origin mode is enabled, frames destined for non-unicast addresses are not forwarded if their source address has the Origin flag set. |
| CTR chInCRCs | 1.3.6.1.4.1.26.2.17.1.9 | Counter | read-only | The number of packets for which a CRC error has been detected. For channels on which CRC errors can not occur, this object always has a value of 0. |
| CTR chInOverruns | 1.3.6.1.4.1.26.2.17.1.10 | Counter | read-only | The number of received packets for which an overrun error occurred. For channels on which overruns can not occur, this object always has a value of 0. |
| CTR chOutColls | 1.3.6.1.4.1.26.2.17.1.11 | Counter | read-only | On a CSMA/CD interface, the number of packets for which a collision occurred during transmission. On any other type of interface, this counter is always zero. |
| CTR chWhos | 1.3.6.1.4.1.26.2.17.1.12 | Counter | read-only | On a token-bus interface, the number of times the bridge had to ask who its successor is. On any other type of interface, the value of this counter is always zero. |
| CTR chInRunts | 1.3.6.1.4.1.26.2.17.1.13 | Counter | read-only | The number of undersize packets received on this channel. |
| CTR chInGiants | 1.3.6.1.4.1.26.2.17.1.14 | Counter | read-only | The number of oversize packets received on this channel. |
| CTR chInLenErrors | 1.3.6.1.4.1.26.2.17.1.15 | Counter | read-only | The number of packets received on this channel, for which the number of bytes received was less than the value in the length field of the packet's header. |
| CTR chInLocks | 1.3.6.1.4.1.26.2.17.1.16 | Counter | read-only | The number of times an interface was reset because the interface's receive deadman timer expired. |
| CTR chOutLocks | 1.3.6.1.4.1.26.2.17.1.17 | Counter | read-only | The number of times an interface was reset because the interface's transmit deadman timer expired. |
| CTR chNoBuffers | 1.3.6.1.4.1.26.2.17.1.18 | Counter | read-only | The number of packets not received because the system was temporarily out of buffers, and so could not transfer the data into memory. |
| INT channelNumber | 1.3.6.1.4.1.26.2.17.1.19 | INTEGER | not-accessible | The channel number |
| OCT protocolBlocking | 1.3.6.1.4.1.26.2.18 | OCTET STRING | read-only | The set of protocols for which the bridge will not forward any packets. Each octet contains a non-zero value if the corresponding protocol is to be blocked. The octets correspond to the protocols, as follows: 1st octet: IP 2nd octet: ARP 3rd octet: RARP 4th octet: reserved (must be zero) 5th octet: DECNET 6th octet: IPX 7th octet: V2 8th octet: XNS 9th octet: TOPS 10th octet: BridgeID (3Com T/Servers) 11th octet: LAT 12th octet: AppleTalk |
| resetLogTable | 1.3.6.1.4.1.26.2.19 | not-accessible | Entries in this table record the reasons and times of the most recent resets of the bridge. | |
| resetLogEntry | 1.3.6.1.4.1.26.2.19.1 | not-accessible | The reason why the bridge was reset, and of how long it was up prior to the reset recorded by this entry. | |
| INT reason | 1.3.6.1.4.1.26.2.19.1.1 | INTEGER | read-only | The reason for the reset. |
| OCT uptime | 1.3.6.1.4.1.26.2.19.1.2 | OCTET STRING | read-only | The length of time, in seconds, the bridge had been up prior to the reset represented by this entry. |
| INT entryNumber | 1.3.6.1.4.1.26.2.19.1.3 | INTEGER | not-accessible | The number of this entry where the most recent is entry number 1, the second most recent is entry number 2, etc. |
| INT packetSize | 1.3.6.1.4.1.26.2.20 | INTEGER | read-write | The range of frame sizes to be forwarded onto an Ethernet/802.3 network by this bridge. The value standard(1) represents the standard range of 60 through 1536 bytes. The value extended(2) represents the (non-standard) range of 16 through 2100 bytes. |
| INT transmitDeadmanTimer | 1.3.6.1.4.1.26.2.21 | INTEGER | read-write | The deadman timer for frame transmission on an interface. The value is the maximum length of time, in units of 160 milliseconds, that a frame will await transmission before the interface is reset. |
| INT receiveDeadmanTimer | 1.3.6.1.4.1.26.2.22 | INTEGER | read-write | The deadman timer for frame reception on an interface. The value is not given in units of time, but rather as a count of frames transmitted on the interface. If no frames are received on the interface during the interval taken to transmit this count of frames, then the interface is reset. |
| tokenRingBridge | 1.3.6.1.4.1.26.2.23 | |||
| INT trBridgeNumber | 1.3.6.1.4.1.26.2.23.1 | INTEGER | read-write | The number of this bridge as used in the 802.5 source routing scheme. |
| trChannelTable | 1.3.6.1.4.1.26.2.23.2 | not-accessible | The table which contains an entry per Token-Ring channel on this bridge. Note that entries exist for 'virtual token-ring' channels as well as real token-ring channels. | |
| trChannelEntry | 1.3.6.1.4.1.26.2.23.2.1 | not-accessible | The set of attributes applicable to each of the bridge's Token-Ring channels. | |
| INT trRingNumber | 1.3.6.1.4.1.26.2.23.2.1.1 | INTEGER | read-write | The ring number of this channel as used in the 802.5 source routing |
| INT trSRAstate | 1.3.6.1.4.1.26.2.23.2.1.2 | INTEGER | read-write | This object affects the Source Routing Accelerator (SRA) chip of the TMS-380 chip set interfacing to this channel. When this object has the value of enabled(1), the SRA chip is used in performing the 802.5 source routing; with the value disabled(2), the SRA chip is not used. |
| protocolFilterTable | 1.3.6.1.4.1.26.2.24 | not-accessible | The table which identifies which protocols are being forwarded by the bridge and which are being blocked. | |
| protocolFilterEntry | 1.3.6.1.4.1.26.2.24.1 | not-accessible | There is one entry in this table for each protocol specifically forwarded or filtered. The first entry is special in that it specifies the handling of all protocols which do not have their own entry. | |
| INT protocolFilterStatus | 1.3.6.1.4.1.26.2.24.1.1 | INTEGER | read-write | Identifies whether the protocol referenced by this entry is being forwarded or blocked by the bridge. Writing a value of invalid(3) to an instance of this object removes the corresponding entry from the table (thereby causing it to be forwarded/blocked according to the 'others' entry). Setting the 'others' entry has the special effect of removing all other entries. Setting the 'others' entry to invalid(3) is not valid. |
| INT protocolFilterType | 1.3.6.1.4.1.26.2.24.1.2 | INTEGER | read-write | Identifies the protocol to which this entry refers. This object takes the value 1 for the first entry in the table which has the special meaning of 'others' in that all protocols which do not have their own entry, are forwarded or blocked as are 'others'. The following values for this object are also defined: 2 - IP 3 - ARP 4 - RARP 5 - DECNET 6 - IPX 7 - V2 8 - XNS 9 - TOPS 10 - BridgeID (3Com T/Servers) 11 - LAT 12 - Appletalk All values greater than 1518, identify the protocolwhich has that value as its 'Ether-type'. |
| INT sysType | 1.3.6.1.4.1.26.3 | INTEGER | read-only | The type of system in which the agent is running |
| INT serialNumber | 1.3.6.1.4.1.26.4 | INTEGER | read-only | The serial number of the system being managed. |
| STR bootPromVersion | 1.3.6.1.4.1.26.5 | DisplayString | read-only | The version number of the boot prom in the system. The value is an ASCII string. |
| INT sysAdmAccess | 1.3.6.1.4.1.26.6 | INTEGER | read-write | The method being used to authenticate a user of the system's console/administrative port. |
| STR appSwVersion | 1.3.6.1.4.1.26.7 | DisplayString | read-only | The version number of the application-software the system is executing. This value is an ASCII string. |
| OCT userProfile | 1.3.6.1.4.1.26.8 | OCTET STRING | read-only | |
| INT hlsMibVersion | 1.3.6.1.4.1.26.9 | INTEGER | read-only | The version number of the HLS-defined MIB extensions supported by the agent. The version of the HLS MIB defined in this document is versionB(2). |
| IP myManager | 1.3.6.1.4.1.26.10 | IpAddress | read-only | The manager to which the agent sends traps. |
| INT sysReset | 1.3.6.1.4.1.26.11 | INTEGER | write-only | Writing to this object causes the agent to reset its system. The value written to the object determines the reset-level. |
| INT clearCounters | 1.3.6.1.4.1.26.12 | INTEGER | write-only | Writing any value to this object causes the agent to clear (i.e. set to zero) the values of all instances of object-types having the syntax: Counter. |
| STR systemDate | 1.3.6.1.4.1.26.13 | DisplayString | read-write | The current system date as known by the agent, formatted as an ASCII string: MM-DD-YY. |
| STR systemTime | 1.3.6.1.4.1.26.14 | DisplayString | read-write | The current system time as known by the agent, formatted as an ASCII string: HH:MM:SS. |
| OCT alarmOption | 1.3.6.1.4.1.26.15 | OCTET STRING | read-write | |
| INT snmpAccess | 1.3.6.1.4.1.26.16 | INTEGER | read-only | |
| IP myIpAddress | 1.3.6.1.4.1.26.17 | IpAddress | read-write | The agent's IP Address. When a new value is written to this object, the system's IP Address is changed immediately after responding to the request. |
| IP defaultGateway | 1.3.6.1.4.1.26.18 | IpAddress | read-write | The IP gateway, to which IP datagrams destined for a remote network will be sent unless and until directed otherwise by an ICMP Redirect. |
| IP netMask | 1.3.6.1.4.1.26.19 | IpAddress | read-write | The network mask associated with myIpAddress. The value of the mask is an IP Address with all network bits set to 1, and all host bits set to 0. |
| hlsSystem | 1.3.6.1.4.1.26.20 | |||
| INT snmpAuth | 1.3.6.1.4.1.26.20.1 | INTEGER | read-write | The method by which the agent is to authenticate the SNMP requests it receives. Both the hlsPassword(1) and the hlsPfx(2) methods require that the use of an 'association' set-up via an HLS-defined extension to the SNMP protocol. The value of snmpCommunity(3) specifies the SNMP standard use of a community-name. The value none(0) specifies that no authentication checking is done. |
| trapTable | 1.3.6.1.4.1.26.20.5 | not-accessible | The table which identifies the parameters associated with the agent's generation of SNMP traps. | |
| trapEntry | 1.3.6.1.4.1.26.20.5.1 | not-accessible | There is one entry of this table for each destination to which the agent sends SNMP traps. | |
| IP trapDestination | 1.3.6.1.4.1.26.20.5.1.1 | IpAddress | read-write | The destination IP Address to which traps enabled in this entry's switches are sent. Writing to an instance of this object-type which does not currently exist, causes a new entry in the table to be created with default settings for the trap switches, except when the table already contains entries for the maximum number of trap destinations the agent supports. |
| OCT genericTrapSwitches | 1.3.6.1.4.1.26.20.5.1.2 | OCTET STRING | read-write | This object's value contains one octet for each type of SNMP-standard generic trap. If the agent is enabled to send a particular type of trap to this entry's destination, the corresponding octet contains a non-zero value; otherwise, if the corresponding octet has a zero value, the agent is disabled from sending that type of trap to this entry's destination. Writing to an instance of this object-type which does not currently exist is an error. The octets for specific traps are positioned in the OCTET STRING, according to their values in the 'generic-trap' field of an SNMP trap message: octet generic-trap field 1st coldStart(0) 2nd warmStart(1) 3rd linkDown(2) etc. |
| OCT specificTrapSwitches | 1.3.6.1.4.1.26.20.5.1.3 | OCTET STRING | read-write | This object's value contains one octet for each type of enterprise-specific trap. If the agent is enabled to send a particular type of trap to this entry's destination, the corresponding octet contains a non-zero value; otherwise, if the corresponding octet has a zero value, the agent is disabled from sending that type of trap to this entry's destination. Writing to an instance of this object-type which does not currently exist is an error. The octets for specific traps are positioned in the OCTET STRING, according to their values in the 'specific-trap' field of an SNMP trap message: octet value of specific-trap 1st 0 2nd 1 3rd 2 etc. Note that enterprise-specific traps must be enabled by the setting of the appropriate octet of genericTrapSwitches, before the value of this object takes effect. |
| INT trapEntryNumber | 1.3.6.1.4.1.26.20.5.1.4 | INTEGER | not-accessible | An integer in the range 1 <= i <= N, where N is the maximum number of trap destinations for this agent. |
| hlsTemporary | 1.3.6.1.4.1.26.21 | |||
| hlsDot1dBridge | 1.3.6.1.4.1.26.21.1 | |||
| hlsDot1dBase | 1.3.6.1.4.1.26.21.1.1 | |||
| MAC hlsDot1dBaseBridgeAddress | 1.3.6.1.4.1.26.21.1.1.1 | MacAddress | read-only | The MAC address used by this bridge when it must be referred to in a unique fashion. It is recommended that this be the numerically smallest MAC address of all ports that belong to this bridge. However it is only required to be unique. When concatenated with hlsDot1dStpPriority a unique BridgeIdentifier is formed which is used in the Spanning Tree Protocol. |
| INT hlsDot1dBaseNumPorts | 1.3.6.1.4.1.26.21.1.1.2 | INTEGER | read-only | The number of ports controlled by this bridging entity. The value can also be determined by examining the number of entries in the port- specific table in the appropriate group. Thus, this object is a candidate for removal. |
| TIK hlsDot1dBaseBridgeUpTime | 1.3.6.1.4.1.26.21.1.1.3 | TimeTicks | read-only | The time (in hundredths of a second) since the bridging entity was last reset or initialized. |
| INT hlsDot1dBaseType | 1.3.6.1.4.1.26.21.1.1.4 | INTEGER | read-only | Indicates what type of bridging this bridge can perform. If a bridge is actually performing a certain type of bridging this will be indicated by entries in the port table for the given type. |
| hlsDot1dBasePortTable | 1.3.6.1.4.1.26.21.1.1.5 | not-accessible | A table that contains generic information about every port that is associated with this bridge. Transparent, source-route, and srt ports are included. | |
| hlsDot1dBasePortEntry | 1.3.6.1.4.1.26.21.1.1.5.1 | not-accessible | A list of information for each port of the bridge. | |
| INT hlsDot1dBasePortIfIndex | 1.3.6.1.4.1.26.21.1.1.5.1.1 | INTEGER | read-only | Identifies the port for which this entry contains bridge management information. The value of this object for a particular port has the same value as the ifIndex object, defined in [4,6], for the corresponding interface. |
| CTR hlsDot1dBasePortNoBufferDiscards | 1.3.6.1.4.1.26.21.1.1.5.1.2 | Counter | read-only | The number of frames discarded by this port due to insufficient internal buffering. It is incremented by both transparent and source route bridges. |
| CTR hlsDot1dBasePortDelayExceededDiscards | 1.3.6.1.4.1.26.21.1.1.5.1.3 | Counter | read-only | The number of frames discarded by this port due to excessive transit delay through the bridge. It is incremented by both transparent and source route bridges. |
| CTR hlsDot1dBasePortMtuExceededDiscards | 1.3.6.1.4.1.26.21.1.1.5.1.4 | Counter | read-only | The number of frames discarded by this port due to an excessive size. It is incremented by both transparent and source route bridges. |
| hlsDot1dStp | 1.3.6.1.4.1.26.21.1.2 | |||
| INT hlsDot1dStpProtocolSpecification | 1.3.6.1.4.1.26.21.1.2.1 | INTEGER | read-only | An indication of what version of the Spanning Tree Protocol is being run. Early DEC Spanning Tree implementations will return 'decprotocol(2)'. IEEE 802.1d implementations will return 'ieee8021d(3)'. If future versions of the IEEE Spanning Tree Protocol are released that are incompatible with the current version a new value will be defined. |
| INT hlsDot1dStpPriority | 1.3.6.1.4.1.26.21.1.2.2 | INTEGER | read-write | In a Spanning Tree Protocol PDU, this bridge is identified by an 8 octet string composed of hlsDot1dStpPriority concatenated with hlsDot1dBaseId. One of the uses of this 8 octet string is to determine the root of the spanning tree. |
| TIK hlsDot1dStpLastTopChange | 1.3.6.1.4.1.26.21.1.2.3 | TimeTicks | read-only | The value of sysUptIme on the occurrence of last time a topology change was detected by the bridge entity. |
| CTR hlsDot1dStpTopChanges | 1.3.6.1.4.1.26.21.1.2.4 | Counter | read-only | The total number of topology changes detected by this bridge since the management entity was last reset or initialized. |
| OCT hlsDot1dStpDesignatedRoot | 1.3.6.1.4.1.26.21.1.2.5 | OCTET STRING | read-only | The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node. |
| INT hlsDot1dStpRootCost | 1.3.6.1.4.1.26.21.1.2.6 | INTEGER | read-only | The cost of the path to the root as seen from this bridge. |
| INT hlsDot1dStpRootPort | 1.3.6.1.4.1.26.21.1.2.7 | INTEGER | read-only | Identifies the port which offers the lowest cost path from this bridge to the root bridge. The value of this object indicates the port for which the ifIndex object, defined in [4,6], of the corresponding interface has the same value. |
| TIK hlsDot1dStpMaxAge | 1.3.6.1.4.1.26.21.1.2.8 | TimeTicks | read-only | The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using. |
| TIK hlsDot1dStpHelloTime | 1.3.6.1.4.1.26.21.1.2.9 | TimeTicks | read-only | The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using. |
| TIK hlsDot1dStpForwardDelay | 1.3.6.1.4.1.26.21.1.2.10 | TimeTicks | read-only | This time value is measured in units of hundredths of a second. It is used for two purposes. Firstly, it controls how fast a port changes its spanning state when moving towards the Forwarding state. In this case, the value determines how long the port stays in a particular state before moving to the next state. For example, how long a port stays in the Listening state when moving from Blocking to Learning. Secondly, when a topology change has been detected and is underway, this time value is used to age all dynamic entries in the Forwarding Database. This is the actual value that this bridge is currently using. |
| TIK hlsDot1dStpHoldTime | 1.3.6.1.4.1.26.21.1.2.11 | TimeTicks | read-only | This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second. |
| hlsDot1dStpPortTable | 1.3.6.1.4.1.26.21.1.2.12 | not-accessible | A table that contains port-specific information for the Spanning Tree Protocol. | |
| hlsDot1dStpPortEntry | 1.3.6.1.4.1.26.21.1.2.12.1 | not-accessible | A list of information maintained by every port about the Spanning Tree Protocol state for that port. | |
| INT hlsDot1dStpPortIfIndex | 1.3.6.1.4.1.26.21.1.2.12.1.1 | INTEGER | read-only | Identifies the port for which this entry contains Spanning Tree Protocol management information. The value of this object for a particular port has the same value as the ifIndex object, defined in [4,6], for the corresponding interface. |
| OCT hlsDot1dStpPortPriority | 1.3.6.1.4.1.26.21.1.2.12.1.2 | OCTET STRING | read-write | The concatenation of hlsDot1dStpPortPriority and hlsDot1dStpPortNum make up the Port Identifier parameter in all Configuration bridge PDUs output by this port. |
| INT hlsDot1dStpPortPortNum | 1.3.6.1.4.1.26.21.1.2.12.1.3 | INTEGER | read-only | This object when concatentated with hlsDot1dStpPortPriority make up the Port Identifier included in all bridge PDUs generated by this bridge. The value of this object is always the same as hlsDot1dStpPortIfIndex for the same port. |
| INT hlsDot1dStpPortState | 1.3.6.1.4.1.26.21.1.2.12.1.4 | INTEGER | read-only | The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the broken(7) state. Implementations that permit remote administratinve control of a port may permit writing of the values disabled(1) and enabled(2). When a port is writen with the value enabled(2) the implementation will take the port to the appropriate state. |
| MAC hlsDot1dStpPortMultiCastAddr | 1.3.6.1.4.1.26.21.1.2.12.1.5 | MacAddress | read-only | The MAC address used as the destination for all Spanning Tree Protocol PDU generated out this port. |
| INT hlsDot1dStpPortPathCost | 1.3.6.1.4.1.26.21.1.2.12.1.6 | INTEGER | read-write | The contribution of this port to the path cost of paths towards the spanning tree root which include this port. |
| OCT hlsDot1dStpPortDesignatedRoot | 1.3.6.1.4.1.26.21.1.2.12.1.7 | OCTET STRING | read-only | The value of the Bridge Identifier that should be seen in bridge PDUs received on this port. |
| INT hlsDot1dStpPortDesignatedCost | 1.3.6.1.4.1.26.21.1.2.12.1.8 | INTEGER | read-only | The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs. |
| OCT hlsDot1dStpPortDesignatedBridge | 1.3.6.1.4.1.26.21.1.2.12.1.9 | OCTET STRING | read-only | The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment. |
| OCT hlsDot1dStpPortDesignatedPort | 1.3.6.1.4.1.26.21.1.2.12.1.10 | OCTET STRING | read-only | The Port Identifier of the port on the Designated Bridge for this port's segment. |
| CTR hlsDot1dStpPortInBPDUs | 1.3.6.1.4.1.26.21.1.2.12.1.11 | Counter | read-only | The number of Spanning Tree Protocol BPDUs received on this port. |
| CTR hlsDot1dStpPortOutBPDUs | 1.3.6.1.4.1.26.21.1.2.12.1.12 | Counter | read-only | The number of Spanning Tree Protocol BPDUs transmitted on this port. |
RFC description
MIB module supporting HLS bridge models with definitions for common bridge objects across various HLS devices.
Start monitoring Hughes LAN Systems networking equipment (legacy, EOL) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.