All MIBs › ES-1000-MIB
Category: Device Management, Technology: Switching/L2, Vendor: Cabletron/Enterasys, Vendor: Edgecore
Description: Manages configuration and monitoring of ES-1000 series Ethernet switch hardware.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is ES-1000-MIB?
ES-1000-MIB is a vendor MIB for the ES-1000 series Ethernet switch, intended to expose configuration and monitoring objects specific to that switch model line. Based on its category, it would generally cover switch-level configuration and status data such as port/interface state and basic device management parameters, though the specific object definitions and module description were not available for this entry. Its purpose in the field is to support monitoring of the switch's operational hardware status, such as port up/down state and basic system health, alongside standard interface counters. No explicit dependency information is available in the source, though switch MIBs of this type commonly build on IF-MIB and SNMPv2-MIB conventions. It would typically be deployed in small-to-midsize LAN environments using ES-1000 series switches, polled by a network management station for basic port and device status. Network engineers evaluating or troubleshooting this functionality can download the ES-1000-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in ES-1000-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- McData ES-1000 series switch — Identified as McData Corporation via enterprise OID 289 (token 'mcData'), a Fibre Channel/SAN switch vendor, not a generic unattributed Ethernet switch as previously described.
Monitoring Examples
No object or table names were available in the source material for this MIB, so a concrete polling scenario using its specific OIDs cannot be honestly constructed here. In practice an ES-1000 series switch would be expected to expose port status and basic system information through this MIB, but without sample objects the specifics could not be confirmed.
This MIB depends on
Related MIBs
Imported Objects
From RFC-1212
| OBJECT-TYPE |
From RFC-1215
| TRAP-TYPE |
From RFC1155-SMI
| Counter | |
| enterprises |
From SNMPv2-TC
| DisplayString |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| mcData | 1.3.6.1.4.1.289 | |||
| NTF es1000PortBportScn | 1.3.6.1.4.1.289.0.1 | A es1000PortBportScn is generated whenever a B_Port changes its operational state. For instance, the B_Port goes from online to offline. | ||
| NTF es1000PortHportScn | 1.3.6.1.4.1.289.0.2 | A es1000PortHportScn is generated whenever a H_Port changes its operational state. For instance, the H_Port goes from online to offline. | ||
| NTF es1000CompScn | 1.3.6.1.4.1.289.0.3 | A es1000CompScn is generated whenever a COMPONENT status changes its operational state. | ||
| commDev | 1.3.6.1.4.1.289.2 | |||
| fibreChannel | 1.3.6.1.4.1.289.2.1 | |||
| fcSwitch | 1.3.6.1.4.1.289.2.1.1 | |||
| es_1000 | 1.3.6.1.4.1.289.2.1.1.3 | |||
| es1000Sys | 1.3.6.1.4.1.289.2.1.1.3.1 | |||
| STR es1000SysCurrentDate | 1.3.6.1.4.1.289.2.1.1.3.1.1 | DisplayString | read-only | The current date information. |
| STR es1000SysBootDate | 1.3.6.1.4.1.289.2.1.1.3.1.2 | DisplayString | read-only | The date and time of the last IPL. |
| STR es1000SysFirmwareVersion | 1.3.6.1.4.1.289.2.1.1.3.1.3 | DisplayString | read-only | The current version of the firmware. |
| STR es1000SysTypeNum | 1.3.6.1.4.1.289.2.1.1.3.1.4 | DisplayString | read-only | This object identifies ASCII type number for the unit (ex. 001000). |
| STR es1000SysModelNum | 1.3.6.1.4.1.289.2.1.1.3.1.5 | DisplayString | read-only | This object identifies ASCII model number for the unit (ex. 001). |
| STR es1000SysMfg | 1.3.6.1.4.1.289.2.1.1.3.1.6 | DisplayString | read-only | This object identifies ASCII manufacturer for the unit (ex. MCD). |
| STR es1000SysPlantOfMfg | 1.3.6.1.4.1.289.2.1.1.3.1.7 | DisplayString | read-only | This object identifies ASCII plant of manufacturer for the unit (ex. 01). |
| STR es1000SysSeqNum | 1.3.6.1.4.1.289.2.1.1.3.1.8 | DisplayString | read-only | This object identifies ASCII sequence number for the unit (ex. 000000000001). |
| STR es1000SysEcLevel | 1.3.6.1.4.1.289.2.1.1.3.1.9 | DisplayString | read-only | This object identifies ASCII EC level ID for the unit (format: xyymmdd, x=millennium). |
| STR es1000SysOemSerialNum | 1.3.6.1.4.1.289.2.1.1.3.1.10 | DisplayString | read-only | This object identifies ASCII OEM serial number for the unit (format: xyymmdd, x=millennium). |
| ES1 es1000SysOperStatus | 1.3.6.1.4.1.289.2.1.1.3.1.11 | Es1000SysOperStatus | read-only | The current operational status of the switch. The values are defined as follows: operational(1), redundant-failure(2), minor-failure(3), major-failure(4), and not-operational(5). |
| ES1 es1000SysState | 1.3.6.1.4.1.289.2.1.1.3.1.12 | Es1000SysState | read-only | If the edOperStatus of the switch is operational, the switch will be in one of the four states: online(1), coming-online(2), offline(3), and going-offline(4). |
| INT es1000SysAdmStatus | 1.3.6.1.4.1.289.2.1.1.3.1.13 | INTEGER | read-write | The desired administrative status of the switch. A management station may place the switch in a desired state by setting this object accordingly. The desired administrative status are online(1) and offline(2). Online means setting the switch to be accessible by an external Fibre Channel port, and offline means setting the switch to be inaccessible. |
| es1000Comp | 1.3.6.1.4.1.289.2.1.1.3.2 | |||
| es1000CompTable | 1.3.6.1.4.1.289.2.1.1.3.2.1 | not-accessible | A table that contains one entry for each component. | |
| es1000CompEntry | 1.3.6.1.4.1.289.2.1.1.3.2.1.1 | not-accessible | An entry containing the service parameters of the component. | |
| ES1 es1000CompCode | 1.3.6.1.4.1.289.2.1.1.3.2.1.1.1 | Es1000CompCode | read-only | Component. A hardware unit of the product. Each component defined in this MIB has a fixed COMPONENT code, except for port components which vary based on the installed GBIC. The values are defined as follows: comp-ctp(2), comp-fan(5), comp-power(6), comp-thermal(13), comp-gbic-none(16), comp-gbic-cu-db9(17), comp-gbic-cu-hssdc(18), comp-gbic-opt-lw-1g(19), comp-gbic-serial(20), comp-gbic-opt-sw-1g(21), comp-gbic-opt-lw-2g(22), comp-gbic-opt-sw-2g(23) |
| ES1 es1000CompPosition | 1.3.6.1.4.1.289.2.1.1.3.2.1.1.2 | Es1000CompPosition | read-only | This object identifies the position of the component. CTP components start from 1 to 1, fans from 1 to 6, power supplies from 1 to 2, thermal sensors from 1 to 1, port GBICs from 1 to 9. |
| ES1 es1000CompStatus | 1.3.6.1.4.1.289.2.1.1.3.2.1.1.3 | Es1000CompStatus | read-only | This object identifies the operational status of the component. The active(1) state indicates that the current component is active. The update-busy(2) state indicates that the component is in the updating process. The failed(3) state indicates the current component is failed. |
| es1000Port | 1.3.6.1.4.1.289.2.1.1.3.3 | |||
| ES1 es1000PortBportCount | 1.3.6.1.4.1.289.2.1.1.3.3.1 | Es1000PortCount | read-only | The number of physical B_Ports available. |
| ES1 es1000PortHportCount | 1.3.6.1.4.1.289.2.1.1.3.3.2 | Es1000PortCount | read-only | The number of physical H_Ports available. |
| es1000PortBportTable | 1.3.6.1.4.1.289.2.1.1.3.3.3 | not-accessible | A table that contains one entry for each B_Port. | |
| es1000PortBportEntry | 1.3.6.1.4.1.289.2.1.1.3.3.3.1 | not-accessible | An entry containing the information for the B_Port. | |
| ES1 es1000PortBportIndex | 1.3.6.1.4.1.289.2.1.1.3.3.3.1.1 | Es1000PortIndex | read-only | This object identifies the B_Port. |
| ES1 es1000PortBportNumber | 1.3.6.1.4.1.289.2.1.1.3.3.3.1.2 | Es1000PortNumber | read-only | This object identifies the B_Port number. |
| ES1 es1000PortBportPhyState | 1.3.6.1.4.1.289.2.1.1.3.3.3.1.3 | Es1000PortPhyState | read-only | This object identifies the physical state of the B_Port. |
| ES1 es1000PortBportOpStatus | 1.3.6.1.4.1.289.2.1.1.3.3.3.1.4 | Es1000PortStatus | read-only | This object identifies the operational status of the B_Port. The online(1) state indicates that user frames can be passed. |
| ES1 es1000PortBportAdmStatus | 1.3.6.1.4.1.289.2.1.1.3.3.3.1.5 | Es1000PortAdmStatus | read-write | The desired state of the B_Port. A management station may place the B_Port in a desired state by setting this object accordingly. The testing(3) state indicates that no user frames can be passed. As the result of either explicit management action or per configuration information accessible by the B_Port, the es1000PortBportAdmStatus is changed to either the online(1) or testing(3) states, or remains in the offline(2) state. |
| STR es1000PortBportName | 1.3.6.1.4.1.289.2.1.1.3.3.3.1.6 | DisplayString | read-write | The desired name of the B_Port. |
| T/F es1000PortBportBlockedState | 1.3.6.1.4.1.289.2.1.1.3.3.3.1.7 | TruthValue | read-write | The desired blocked state of the B_Port. Blocking a B_Port prevents it from communicating with its attached E_Port. A blocked B_Port will continuously transmit the Off-Line Sequence (OLS). |
| es1000PortHportTable | 1.3.6.1.4.1.289.2.1.1.3.3.4 | not-accessible | A table that contains one entry for each H_Port. | |
| es1000PortHportEntry | 1.3.6.1.4.1.289.2.1.1.3.3.4.1 | not-accessible | An entry containing the information for the H_Port. | |
| ES1 es1000PortHportIndex | 1.3.6.1.4.1.289.2.1.1.3.3.4.1.1 | Es1000PortIndex | read-only | This object identifies the H_Port. |
| ES1 es1000PortHportNumber | 1.3.6.1.4.1.289.2.1.1.3.3.4.1.2 | Es1000PortNumber | read-only | This object identifies the H_Port number. |
| ES1 es1000PortHportPhyState | 1.3.6.1.4.1.289.2.1.1.3.3.4.1.3 | Es1000PortPhyState | read-only | This object identifies the physical state of the H_Port. |
| ES1 es1000PortHportOpStatus | 1.3.6.1.4.1.289.2.1.1.3.3.4.1.4 | Es1000PortStatus | read-only | This object identifies the operational status of the H_Port. The online(1) state indicates that user frames can be passed. |
| ES1 es1000PortHportAdmStatus | 1.3.6.1.4.1.289.2.1.1.3.3.4.1.5 | Es1000PortAdmStatus | read-write | The desired state of the H_Port. A management station may place the H_Port in a desired state by setting this object accordingly. The testing(3) state indicates that no user frames can be passed. As the result of either explicit management action or per configuration information accessible by the switch, the es1000PortHportAdmStatus is changed to either the online(1) or testing(3) states, or remains in the offline(2) state. |
| STR es1000PortHportName | 1.3.6.1.4.1.289.2.1.1.3.3.4.1.6 | DisplayString | read-write | The desired name of the H_Port. |
| T/F es1000PortHportBypassedState | 1.3.6.1.4.1.289.2.1.1.3.3.4.1.7 | TruthValue | read-write | The desired bypassed state of the H_Port. Bypassing an H_Port prevents an attached device from communicating with the switch or communicating with any other device attached to the switch. Bypassing a port causes the incoming signal from an attached device to not placed on the Loop. |
| T/F es1000PortHportValidation | 1.3.6.1.4.1.289.2.1.1.3.3.4.1.8 | TruthValue | read-write | The desired port validation state of the H_Port. If enabled, then a more rigorous process of validating the attached device is performed before insertion into the Loop. |
| T/F es1000PortHportLipOnInsertion | 1.3.6.1.4.1.289.2.1.1.3.3.4.1.9 | TruthValue | read-write | The desired LIP on Insertion state of the H_Port. If enabled, a LIP will be automatically sent after any port insertion, port bypass, or manual GBIC installation or removal. |
| es1000Loop | 1.3.6.1.4.1.289.2.1.1.3.4 | |||
| ES1 es1000LoopStatus | 1.3.6.1.4.1.289.2.1.1.3.4.1 | Es1000LoopStatus | read-only | The current loop status of the switch. The values are defined as follows: DOWN(1), LIP(2), LISM(3), LIFA(4), LIPA(5), LIHA(6), LISA(7), LIRP(8), LILP(9), FAN(10), ACTIVE(11), and READY(12). |
| ES1 es1000LoopMasterWWN | 1.3.6.1.4.1.289.2.1.1.3.4.2 | Es1000LoopMasterWWN | read-only | The loop master worldwide name. If the loop master is unknown, then the worldwide name will be all zeros. |
| T/F es1000LoopSwitched | 1.3.6.1.4.1.289.2.1.1.3.4.3 | TruthValue | read-only | Indicates whether switching mode is enabled. If enabled, each pair of communicating H_Ports may share the 100 Mbyte bandwidth. If not enabled, all devices on the loop share the 100 Mbyte bandwidth available on the loop. |
| T/F es1000LoopPrincipal | 1.3.6.1.4.1.289.2.1.1.3.4.4 | TruthValue | read-only | Indicates whether the switch is operating as the principal ES-1000 on the loop. |
| es1000LoopPortTable | 1.3.6.1.4.1.289.2.1.1.3.4.5 | not-accessible | A table that contains the port-to-ALPA mapping for each H_Port on the loop. | |
| es1000LoopPortEntry | 1.3.6.1.4.1.289.2.1.1.3.4.5.1 | not-accessible | An entry containing the ALPA information for the H_Port. | |
| ES1 es1000LoopPortIndex | 1.3.6.1.4.1.289.2.1.1.3.4.5.1.1 | Es1000PortIndex | read-only | This object identifies the Loop port entry. |
| ES1 es1000LoopPortNumber | 1.3.6.1.4.1.289.2.1.1.3.4.5.1.2 | Es1000PortNumber | read-only | This object identifies the H_Port number. |
| ES1 es1000LoopPortALPA | 1.3.6.1.4.1.289.2.1.1.3.4.5.1.3 | Es1000LoopPortALPA | read-only | This object identifies the ALPA's associated with the H_Port. |
| es1000Acct | 1.3.6.1.4.1.289.2.1.1.3.5 | |||
| es1000AcctBportTable | 1.3.6.1.4.1.289.2.1.1.3.5.1 | not-accessible | A table that contains B_Port accounting information recorded since the switch IPL'd. | |
| es1000AcctBportEntry | 1.3.6.1.4.1.289.2.1.1.3.5.1.1 | not-accessible | An entry containing accounting information for each B_Port. | |
| ES1 es1000AcctBportIndex | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.1 | Es1000PortIndex | read-only | This object identifies the B_Port. |
| ES1 es1000AcctBportNumber | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.2 | Es1000PortNumber | read-only | This object identifies the B_Port number. |
| CTR es1000AcctBportLinkFailures | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.3 | Counter | read-only | This object counts the number of Link Failures detected by this B_Port. |
| CTR es1000AcctBportSyncLosses | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.4 | Counter | read-only | This object counts the number of loss of synchronization detected by this B_Port. |
| CTR es1000AcctBportSigLosses | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.5 | Counter | read-only | This object counts the number of loss of signal detected by this B_Port. |
| CTR es1000AcctBportPrimSeqProtoErrors | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.6 | Counter | read-only | This object counts the number of primitive sequence protocol errors detected by this B_Port. |
| CTR es1000AcctBportInvalidTxWords | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.7 | Counter | read-only | This object counts the number of invalid transmission words detected by this B_Port. |
| CTR es1000AcctBportInvalidCrcs | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.8 | Counter | read-only | This object counts the number of invalid CRC detected by this B_Port for frames received. |
| CTR es1000AcctBportLinkResetIns | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.9 | Counter | read-only | This object counts the number of Link Reset Protocol received by this B_Port from the attached E_Port. |
| CTR es1000AcctBportLinkResetOuts | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.10 | Counter | read-only | This object counts the number of Link Reset Protocol issued by this B_Port to the attached E_Port. |
| CTR es1000AcctBportOlsIns | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.11 | Counter | read-only | This object counts the number of Offline Sequence (OLS) received by this B_Port. |
| CTR es1000AcctBportOlsOuts | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.12 | Counter | read-only | This object counts the number of Offline Sequence (OLS) issued by this B_Port. |
| CTR es1000AcctBportC2InFrames | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.13 | Counter | read-only | This object counts the number of Class 2 frames received by this B_Port from its attached E_Port. |
| CTR es1000AcctBportC2OutFrames | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.14 | Counter | read-only | This object counts the number of Class 2 frames delivered through this B_Port to its attached E_Port. |
| CTR es1000AcctBportC2Discards | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.15 | Counter | read-only | This object counts the number of Class 2 frames discarded by this B_Port. |
| CTR es1000AcctBportC2InOctets | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.16 | Counter | read-only | This object counts the number of Class 2 frame octets (bytes), including the frame delimeters, received by this B_Port from its attached E_Port. |
| CTR es1000AcctBportC2OutOctets | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.17 | Counter | read-only | This object counts the number of Class 2 frame octets (bytes), including the frame delimeters, delivered through this B_Port to its attached E_Port. |
| CTR es1000AcctBportC3InFrames | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.18 | Counter | read-only | This object counts the number of Class 3 frames received by this B_Port from its attached E_Port. |
| CTR es1000AcctBportC3OutFrames | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.19 | Counter | read-only | This object counts the number of Class 3 frames delivered through this B_Port to its attached E_Port. |
| CTR es1000AcctBportC3InOctets | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.20 | Counter | read-only | This object counts the number of Class 3 frame octets (bytes), including the frame delimeters, received by this B_Port from its attached E_Port. |
| CTR es1000AcctBportC3OutOctets | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.21 | Counter | read-only | This object counts the number of Class 3 frame octets (bytes), including the frame delimeters, delivered through this B_Port to its attached E_Port. |
| CTR es1000AcctBportC3Discards | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.22 | Counter | read-only | This object counts the number of Class 3 frames discarded by this B_Port. |
| CTR es1000AcctBportRxWords | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.23 | Counter | read-only | This object counts the number of Fibre Channel words, including the frame delimeters, received by this B_Port from its attached E_Port. |
| CTR es1000AcctBportTxWords | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.24 | Counter | read-only | This object counts the number of Fibre Channel words, including the frame delimeters, delivered through this B_Port to its attached E_Port. |
| CTR es1000AcctBportRxFrames | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.25 | Counter | read-only | This object counts the number of Fibre Channel frames received by this B_Port from its attached E_Port. |
| CTR es1000AcctBportTxFrames | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.26 | Counter | read-only | This object counts the number of Fibre Channel frames delivered through this B_Port to its attached E_Port. |
| CTR es1000AcctBportInvalidOrderedSets | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.27 | Counter | read-only | This object counts the number of invalid Ordered Sets received by this B_Port from its attached E_Port. |
| CTR es1000AcctBportFramesTooLong | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.28 | Counter | read-only | This object counts the number of Fibre Channel over length frames received by this B_Port from its attached E_Port. |
| CTR es1000AcctBportFramesTooShort | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.29 | Counter | read-only | This object counts the number of Fibre Channel truncated frames received by this B_Port from its attached E_Port. |
| CTR es1000AcctBportTxThroughput | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.30 | Counter | read-only | This object presents the Bps transmission rate for this B_Port. |
| CTR es1000AcctBportRxThroughput | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.31 | Counter | read-only | This object presents the Bps reception rate for this B_Port. |
| CTR es1000AcctBportAddressErrors | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.32 | Counter | read-only | This object counts the number of Address errors detected by this B_Port. |
| CTR es1000AcctBportC2FbsyFrames | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.33 | Counter | read-only | This object counts the number of F_BSY frames generated by this B_Port against Class 2 frames. |
| CTR es1000AcctBportC2FrjtFrames | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.34 | Counter | read-only | This object counts the number of F_RJT frames generated by this B_Port against Class 2 frames. |
| CTR es1000AcctBportCFInFrames | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.35 | Counter | read-only | This object counts the number of Class F frames received by this B_Port from its attached E_Port. |
| CTR es1000AcctBportFramesDiscarded | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.36 | Counter | read-only | This object counts the number of Fibre Channel frames that this B_Port has discarded. |
| CTR es1000AcctBportInvalidClassofFrame | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.37 | Counter | read-only | This object counts the number of Invalid Class of frame detected by this B_Port. |
| CTR es1000AcctBportC2RxWords | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.38 | Counter | read-only | This object counts the number of Class 2 frame words, including the frame delimeters, received by this B_Port from its attached E_Port. |
| CTR es1000AcctBportC2TxWords | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.39 | Counter | read-only | This object counts the number of Class 2 words, including the frame delimeters, delivered through this B_Port to its attached E_Port. |
| CTR es1000AcctBportC3RxWords | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.40 | Counter | read-only | This object counts the number of Class 3 frame words, including the frame delimeters, received by this B_Port from its attached E_Port. |
| CTR es1000AcctBportC3TxWords | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.41 | Counter | read-only | This object counts the number of Class 3 words, including the frame delimeters, delivered through this B_Port to its attached E_Port. |
| CTR es1000AcctBportTxThroughputPercent | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.42 | Counter | read-only | This object presents the percentage of transmission bandwidth used by this B_Port. |
| CTR es1000AcctBportRxThroughputPercent | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.43 | Counter | read-only | This object presents the percentage of reception bandwidth used by this B_Port. |
| CTR es1000AcctBportLinkDown | 1.3.6.1.4.1.289.2.1.1.3.5.1.1.44 | Counter | read-only | This object counts the number of times the B_Port has detected a link down condition. |
| es1000AcctHportTable | 1.3.6.1.4.1.289.2.1.1.3.5.2 | not-accessible | A table that contains H_Port accounting information recorded since the switch IPL'd. | |
| es1000AcctHportEntry | 1.3.6.1.4.1.289.2.1.1.3.5.2.1 | not-accessible | An entry containing accounting information for each H_Port. | |
| ES1 es1000AcctHportIndex | 1.3.6.1.4.1.289.2.1.1.3.5.2.1.1 | Es1000PortIndex | read-only | This object identifies the H_Port. |
| ES1 es1000AcctHportNumber | 1.3.6.1.4.1.289.2.1.1.3.5.2.1.2 | Es1000PortNumber | read-only | This object identifies the H_Port number. |
| CTR es1000AcctHportLinkFailures | 1.3.6.1.4.1.289.2.1.1.3.5.2.1.3 | Counter | read-only | This object counts the number of Link Failures detected by this H_Port. |
| CTR es1000AcctHportSyncLosses | 1.3.6.1.4.1.289.2.1.1.3.5.2.1.4 | Counter | read-only | This object counts the number of loss of synchronization detected by this H_Port. |
| CTR es1000AcctHportSigLosses | 1.3.6.1.4.1.289.2.1.1.3.5.2.1.5 | Counter | read-only | This object counts the number of loss of signal detected by this H_Port. |
| CTR es1000AcctHportInvalidTxWords | 1.3.6.1.4.1.289.2.1.1.3.5.2.1.6 | Counter | read-only | This object counts the number of invalid transmission words detected by this H_Port. |
| CTR es1000AcctHportInvalidCrcs | 1.3.6.1.4.1.289.2.1.1.3.5.2.1.7 | Counter | read-only | This object counts the number of invalid CRC detected by this H_Port for frames received. |
| CTR es1000AcctHportC2InFrames | 1.3.6.1.4.1.289.2.1.1.3.5.2.1.8 | Counter | read-only | This object counts the number of Class 2 frames received by this H_Port. |
| CTR es1000AcctHportC2OutFrames | 1.3.6.1.4.1.289.2.1.1.3.5.2.1.9 | Counter | read-only | This object counts the number of Class 2 frames delivered through this H_Port. |
| CTR es1000AcctHportC2InOctets | 1.3.6.1.4.1.289.2.1.1.3.5.2.1.10 | Counter | read-only | This object counts the number of Class 2 frame octets (bytes), including the frame delimeters, received by this H_Port. |
| CTR es1000AcctHportC2OutOctets | 1.3.6.1.4.1.289.2.1.1.3.5.2.1.11 | Counter | read-only | This object counts the number of Class 2 frame octets (bytes), including the frame delimeters, delivered through this H_Port. |
| CTR es1000AcctHportC3InFrames | 1.3.6.1.4.1.289.2.1.1.3.5.2.1.12 | Counter | read-only | This object counts the number of Class 3 frames received by this H_Port. |
| CTR es1000AcctHportC3OutFrames | 1.3.6.1.4.1.289.2.1.1.3.5.2.1.13 | Counter | read-only | This object counts the number of Class 3 frames delivered through this H_Port. |
| CTR es1000AcctHportC3InOctets | 1.3.6.1.4.1.289.2.1.1.3.5.2.1.14 | Counter | read-only | This object counts the number of Class 3 frame octets (bytes), including the frame delimeters, received by this H_Port. |
| CTR es1000AcctHportC3OutOctets | 1.3.6.1.4.1.289.2.1.1.3.5.2.1.15 | Counter | read-only | This object counts the number of Class 3 frame octets (bytes), including the frame delimeters, delivered through this H_Port. |
| CTR es1000AcctHportRxWords | 1.3.6.1.4.1.289.2.1.1.3.5.2.1.16 | Counter | read-only | This object counts the number of Fibre Channel words, including the frame delimeters, received by this H_Port. |
| CTR es1000AcctHportTxWords | 1.3.6.1.4.1.289.2.1.1.3.5.2.1.17 | Counter | read-only | This object counts the number of Fibre Channel words, including the frame delimeters, delivered through this H_Port. |
| CTR es1000AcctHportRxFrames | 1.3.6.1.4.1.289.2.1.1.3.5.2.1.18 | Counter | read-only | This object counts the number of Fibre Channel frames received by this H_Port. |
| CTR es1000AcctHportTxFrames | 1.3.6.1.4.1.289.2.1.1.3.5.2.1.19 | Counter | read-only | This object counts the number of Fibre Channel frames delivered through this H_Port. |
| CTR es1000AcctHportTxThroughput | 1.3.6.1.4.1.289.2.1.1.3.5.2.1.20 | Counter | read-only | This object presents the Bps transmission rate for this H_Port. |
| CTR es1000AcctHportRxThroughput | 1.3.6.1.4.1.289.2.1.1.3.5.2.1.21 | Counter | read-only | This object presents the Bps reception rate for this H_Port. |
| CTR es1000AcctHportC2RxWords | 1.3.6.1.4.1.289.2.1.1.3.5.2.1.22 | Counter | read-only | This object counts the number of Class 2 frame words, including the frame delimeters, received by this H_Port. |
| CTR es1000AcctHportC2TxWords | 1.3.6.1.4.1.289.2.1.1.3.5.2.1.23 | Counter | read-only | This object counts the number of Class 2 words, including the frame delimeters, delivered through this H_Port. |
| CTR es1000AcctHportC3RxWords | 1.3.6.1.4.1.289.2.1.1.3.5.2.1.24 | Counter | read-only | This object counts the number of Class 3 frame words, including the frame delimeters, received by this H_Port. |
| CTR es1000AcctHportC3TxWords | 1.3.6.1.4.1.289.2.1.1.3.5.2.1.25 | Counter | read-only | This object counts the number of Class 3 words, including the frame delimeters, delivered through this H_Port. |
| CTR es1000AcctHportTxThroughputPercent | 1.3.6.1.4.1.289.2.1.1.3.5.2.1.26 | Counter | read-only | This object presents the percentage of transmission bandwidth used by this H_Port. |
| CTR es1000AcctHportRxThroughputPercent | 1.3.6.1.4.1.289.2.1.1.3.5.2.1.27 | Counter | read-only | This object presents the percentage of reception bandwidth used by this H_Port. |
| CTR es1000AcctHportLIPCount | 1.3.6.1.4.1.289.2.1.1.3.5.2.1.28 | Counter | read-only | This object counts the number of LIPs detected by this H_Port. |
| CTR es1000AcctHportConnectionsMade | 1.3.6.1.4.1.289.2.1.1.3.5.2.1.29 | Counter | read-only | This object counts the number of connections made by this H_Port. |
| CTR es1000AcctHportConnectionsStalled | 1.3.6.1.4.1.289.2.1.1.3.5.2.1.30 | Counter | read-only | This object counts the number of connections stalled by this H_Port. |
| CTR es1000AcctHportConnectionsAborted | 1.3.6.1.4.1.289.2.1.1.3.5.2.1.31 | Counter | read-only | This object counts the number of connections aborted by this H_Port. |
| CTR es1000AcctHportConnectionsAccepted | 1.3.6.1.4.1.289.2.1.1.3.5.2.1.32 | Counter | read-only | This object counts the number of connections accepted by this H_Port. |
RFC description
Management information for the ES-1000 Fibre Channel Enterprise Connectivity Switch, monitoring ports, components, and fabric status.
Start monitoring McData ES-1000 series switch with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.