BDCOM-SYS

All MIBs › BDCOM-SYS

Category: Device Management, Hardware and Environment, Vendor: BDCOM

Description: Provides system-level management objects including hardware inventory and software version for BDCOM devices.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is BDCOM-SYS?

BDCOM-SYS is a vendor-specific MIB providing system-level management objects for BDCOM networking devices, covering general device identity and status information. No module description or sample objects were available in the source data, so exact object names cannot be confirmed, but based on its short description it exposes hardware inventory details and software version information. Such a system MIB is typically used for baseline hardware/software status monitoring: confirming a device's model, hardware components, and running software/firmware version. As a vendor system MIB it would likely build on the standard SNMPv2-MIB system group (sysDescr, sysObjectID) rather than a specialized standards dependency. It would be deployed wherever BDCOM switches or routers are managed, as part of basic device inventory and version-tracking in network management. Engineers can download the BDCOM-SYS file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in BDCOM-SYS. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

BDCOM network switch/router

Monitoring Examples

Without concrete object names available in the source data, a grounded technical example cannot be given; based on the short description, an operator would likely poll hardware inventory and software version objects to confirm a BDCOM device is running the expected firmware and to verify installed hardware modules match inventory records.

What Can Be Monitored

hardware inventory
software/firmware version
device model identity

Imported Objects

From BDCOM-SMI

bdlocal

OBJECT-IDENTITY

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

IpAddress

From RFC1213-MIB

DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
IP bdauthAddr	1.3.6.1.4.1.3320.2.1.5	IpAddress	read-only	This variable contains the last SNMP authorization failure IP address.
INT bdavgBusy1	1.3.6.1.4.1.3320.2.1.57	INTEGER	read-only	1 minute exponentially-decayed moving average of the CPU busy percentage.
INT bdavgBusy5	1.3.6.1.4.1.3320.2.1.58	INTEGER	read-only	5 minute exponentially-decayed moving average of the CPU busy percentage.
IP bdbootHost	1.3.6.1.4.1.3320.2.1.6	IpAddress	read-only	Contains the IP address of the host that supplied the currently running software.
INT bdbufferBgCreate	1.3.6.1.4.1.3320.2.1.37	INTEGER	read-only	Contains the number of big buffer creates.
INT bdbufferBgFree	1.3.6.1.4.1.3320.2.1.32	INTEGER	read-only	Contains the number of free big buffers.
INT bdbufferBgHit	1.3.6.1.4.1.3320.2.1.34	INTEGER	read-only	Contains the number of big buffer hits.
INT bdbufferBgMax	1.3.6.1.4.1.3320.2.1.33	INTEGER	read-only	Contains the maximum number of big buffers.
INT bdbufferBgMiss	1.3.6.1.4.1.3320.2.1.35	INTEGER	read-only	Contains the number of big buffer misses.
INT bdbufferBgSize	1.3.6.1.4.1.3320.2.1.30	INTEGER	read-only	Contains the size of big buffers.
INT bdbufferBgTotal	1.3.6.1.4.1.3320.2.1.31	INTEGER	read-only	Contains the total number of big buffers.
INT bdbufferBgTrim	1.3.6.1.4.1.3320.2.1.36	INTEGER	read-only	Contains the number of big buffer trims.
INT bdbufferElCreate	1.3.6.1.4.1.3320.2.1.13	INTEGER	read-only	Contains the number of buffer element creates.
INT bdbufferElFree	1.3.6.1.4.1.3320.2.1.9	INTEGER	read-only	Contains the number of free buffer elements.
INT bdbufferElHit	1.3.6.1.4.1.3320.2.1.11	INTEGER	read-only	Contains the number of buffer element hits.
INT bdbufferElMax	1.3.6.1.4.1.3320.2.1.10	INTEGER	read-only	Contains the maximum number of buffer elements.
INT bdbufferElMiss	1.3.6.1.4.1.3320.2.1.12	INTEGER	read-only	Contains the number of buffer element misses.
INT bdbufferFail	1.3.6.1.4.1.3320.2.1.46	INTEGER	read-only	Count of the number of buffer allocation failures.
INT bdbufferHgCreate	1.3.6.1.4.1.3320.2.1.69	INTEGER	read-only	Contains the number of huge buffer creates.
INT bdbufferHgFree	1.3.6.1.4.1.3320.2.1.64	INTEGER	read-only	Contains the number of free huge buffers.
INT bdbufferHgHit	1.3.6.1.4.1.3320.2.1.66	INTEGER	read-only	Contains the number of huge buffer hits.
INT bdbufferHgMax	1.3.6.1.4.1.3320.2.1.65	INTEGER	read-only	Contains the maximum number of huge buffers.
INT bdbufferHgMiss	1.3.6.1.4.1.3320.2.1.67	INTEGER	read-only	Contains the number of huge buffer misses.
INT bdbufferHgSize	1.3.6.1.4.1.3320.2.1.62	INTEGER	read-only	Contains the size of huge buffers.
INT bdbufferHgTotal	1.3.6.1.4.1.3320.2.1.63	INTEGER	read-only	Contains the total number of huge buffers.
INT bdbufferHgTrim	1.3.6.1.4.1.3320.2.1.68	INTEGER	read-only	Contains the number of huge buffer trims.
INT bdbufferLgCreate	1.3.6.1.4.1.3320.2.1.45	INTEGER	read-only	Contains the number of large buffer creates.
INT bdbufferLgFree	1.3.6.1.4.1.3320.2.1.40	INTEGER	read-only	Contains the number of free large buffers.
INT bdbufferLgHit	1.3.6.1.4.1.3320.2.1.42	INTEGER	read-only	Contains the number of large buffer hits.
INT bdbufferLgMax	1.3.6.1.4.1.3320.2.1.41	INTEGER	read-only	Contains the maximum number of large buffers.
INT bdbufferLgMiss	1.3.6.1.4.1.3320.2.1.43	INTEGER	read-only	Contains the number of large buffer misses.
INT bdbufferLgSize	1.3.6.1.4.1.3320.2.1.38	INTEGER	read-only	Contains the size of large buffers.
INT bdbufferLgTotal	1.3.6.1.4.1.3320.2.1.39	INTEGER	read-only	Contains the total number of large buffers.
INT bdbufferLgTrim	1.3.6.1.4.1.3320.2.1.44	INTEGER	read-only	Contains the number of large buffer trims.
INT bdbufferMdCreate	1.3.6.1.4.1.3320.2.1.29	INTEGER	read-only	Contains the number of medium buffer creates.
INT bdbufferMdFree	1.3.6.1.4.1.3320.2.1.24	INTEGER	read-only	Contains the number of free medium buffers.
INT bdbufferMdHit	1.3.6.1.4.1.3320.2.1.26	INTEGER	read-only	Contains the number of medium buffer hits.
INT bdbufferMdMax	1.3.6.1.4.1.3320.2.1.25	INTEGER	read-only	Contains the maximum number of medium buffers.
INT bdbufferMdMiss	1.3.6.1.4.1.3320.2.1.27	INTEGER	read-only	Contains the number of medium buffer misses.
INT bdbufferMdSize	1.3.6.1.4.1.3320.2.1.22	INTEGER	read-only	Contains the size of medium buffers.
INT bdbufferMdTotal	1.3.6.1.4.1.3320.2.1.23	INTEGER	read-only	Contains the total number of medium buffers.
INT bdbufferMdTrim	1.3.6.1.4.1.3320.2.1.28	INTEGER	read-only	Contains the number of medium buffer trims.
INT bdbufferNoMem	1.3.6.1.4.1.3320.2.1.47	INTEGER	read-only	Count of the number of buffer create failures due to no free memory.
INT bdbufferSmCreate	1.3.6.1.4.1.3320.2.1.21	INTEGER	read-only	Contains the number of small buffer creates.
INT bdbufferSmFree	1.3.6.1.4.1.3320.2.1.16	INTEGER	read-only	Contains the number of free small buffers.
INT bdbufferSmHit	1.3.6.1.4.1.3320.2.1.18	INTEGER	read-only	Contains the number of small buffer hits.
INT bdbufferSmMax	1.3.6.1.4.1.3320.2.1.17	INTEGER	read-only	Contains the maximum number of small buffers.
INT bdbufferSmMiss	1.3.6.1.4.1.3320.2.1.19	INTEGER	read-only	Contains the number of small buffer misses.
INT bdbufferSmSize	1.3.6.1.4.1.3320.2.1.14	INTEGER	read-only	Contains the size of small buffers.
INT bdbufferSmTotal	1.3.6.1.4.1.3320.2.1.15	INTEGER	read-only	Contains the total number of small buffers.
INT bdbufferSmTrim	1.3.6.1.4.1.3320.2.1.20	INTEGER	read-only	Contains the number of small buffer trims.
INT bdbusyPer	1.3.6.1.4.1.3320.2.1.56	INTEGER	read-only	CPU busy percentage in the last 5 second period. Not the last 5 realtime seconds but the last 5 second period in the scheduler.
STR bdContactInfo	1.3.6.1.4.1.3320.2.1.61	DisplayString	read-only	BDCom's name and address
STR bddomainName	1.3.6.1.4.1.3320.2.1.4	DisplayString	read-only	This variable is the domain portion of the domain name of the host.
STR bdenvBurnDate	1.3.6.1.4.1.3320.2.1.111	DisplayString	read-only	The calibration / burn in date
STR bdenvFirmVersion	1.3.6.1.4.1.3320.2.1.108	DisplayString	read-only	Description of Environmental Card firmware
INT bdenvPresent	1.3.6.1.4.1.3320.2.1.77	INTEGER	read-only	Is there an environmental monitor card in this box?, 0 - No, 1-AGS card present, wrong firmware, 2-AGS CARD present, firmware ok, 3-7000 support
STR bdenvSerialNumber	1.3.6.1.4.1.3320.2.1.112	DisplayString	read-only	Serial Number of environmental monitor card
STR bdenvTechnicianID	1.3.6.1.4.1.3320.2.1.109	DisplayString	read-only	Technician ID
STR bdenvTestPt1Descr	1.3.6.1.4.1.3320.2.1.78	DisplayString	read-only	Description of the test point 1. Typically ambient air or the temperature of air entering the router
INT bdenvTestPt1last	1.3.6.1.4.1.3320.2.1.96	INTEGER	read-only	Value of TestPt1 when last shutdown occurred.
INT bdenvTestPt1MarginVal	1.3.6.1.4.1.3320.2.1.90	INTEGER	read-only	Value at which the router will shutdown. Typically the ambient air temperature that will shut the router down. (e.g. 43)
INT bdenvTestPt1Measure	1.3.6.1.4.1.3320.2.1.79	INTEGER	read-only	Current value of test point 1. Typically a temperature in centigrade.
INT bdenvTestPt1warn	1.3.6.1.4.1.3320.2.1.102	INTEGER	read-only	Is this test point at a warning level?
STR bdenvTestPt2Descr	1.3.6.1.4.1.3320.2.1.80	DisplayString	read-only	Description of the test point 2. Typically airflow or the temperature of air leaving the router
INT bdenvTestPt2last	1.3.6.1.4.1.3320.2.1.97	INTEGER	read-only	Value of TestPt2 when last shutdown occurred.
INT bdenvTestPt2MarginVal	1.3.6.1.4.1.3320.2.1.91	INTEGER	read-only	Value at which the router will shutdown. Typically the airflow air temperature that will shut the router down. (e.g. 58)
INT bdenvTestPt2Measure	1.3.6.1.4.1.3320.2.1.81	INTEGER	read-only	Current value of test point 2. Typically a temperature in centigrade.
INT bdenvTestPt2warn	1.3.6.1.4.1.3320.2.1.103	INTEGER	read-only	Is this test point at a warning level?
STR bdenvTestPt3Descr	1.3.6.1.4.1.3320.2.1.82	DisplayString	read-only	Description of the test point 3. Typically +5 volt
INT bdenvTestPt3last	1.3.6.1.4.1.3320.2.1.98	INTEGER	read-only	Value of TestPt3 when last shutdown occurred.
INT bdenvTestPt3MarginPercent	1.3.6.1.4.1.3320.2.1.92	INTEGER	read-only	+/- Percentage that will shut the router down, (e.g. 10%) typically +5 volt
INT bdenvTestPt3Measure	1.3.6.1.4.1.3320.2.1.83	INTEGER	read-only	Current value of test point 3. Typically the value in millivolts of the +5v supply
INT bdenvTestPt3warn	1.3.6.1.4.1.3320.2.1.104	INTEGER	read-only	Is this test point at a warning level?
STR bdenvTestPt4Descr	1.3.6.1.4.1.3320.2.1.84	DisplayString	read-only	Description of the test point 4. Typically +12 volt
INT bdenvTestPt4last	1.3.6.1.4.1.3320.2.1.99	INTEGER	read-only	Value of TestPt4 when last shutdown occurred.
INT bdenvTestPt4MarginPercent	1.3.6.1.4.1.3320.2.1.93	INTEGER	read-only	+/- Percentage that will shut the router down, (e.g. 15%) typically +12 volt
INT bdenvTestPt4Measure	1.3.6.1.4.1.3320.2.1.85	INTEGER	read-only	Current value of test point 4. Typically the value in millivolts of the +12v supply
INT bdenvTestPt4warn	1.3.6.1.4.1.3320.2.1.105	INTEGER	read-only	Is this test point at a warning level?
STR bdenvTestPt5Descr	1.3.6.1.4.1.3320.2.1.86	DisplayString	read-only	Description of the test point 5. Typically -12 volt
INT bdenvTestPt5last	1.3.6.1.4.1.3320.2.1.100	INTEGER	read-only	Value of TestPt5 when last shutdown occurred.
INT bdenvTestPt5MarginPercent	1.3.6.1.4.1.3320.2.1.94	INTEGER	read-only	+/- Percentage that will shut the router down, (e.g. 15%) typically -12 volt
INT bdenvTestPt5Measure	1.3.6.1.4.1.3320.2.1.87	INTEGER	read-only	Current value of test point 5. Typically the value in millivolts of the -12v supply
INT bdenvTestPt5warn	1.3.6.1.4.1.3320.2.1.106	INTEGER	read-only	Is this test point at a warning level?
STR bdenvTestPt6Descr	1.3.6.1.4.1.3320.2.1.88	DisplayString	read-only	Description of the test point 6. Typically -5 volt
INT bdenvTestPt6last	1.3.6.1.4.1.3320.2.1.101	INTEGER	read-only	Value of TestPt6 when last shutdown occurred.
INT bdenvTestPt6MarginPercent	1.3.6.1.4.1.3320.2.1.95	INTEGER	read-only	+/- Percentage that will shut the router down, (e.g. 10%) typically -5 volt
INT bdenvTestPt6Measure	1.3.6.1.4.1.3320.2.1.89	INTEGER	read-only	Current value of test point 6. Typically the value in millivolts of the -5v supply
INT bdenvTestPt6warn	1.3.6.1.4.1.3320.2.1.107	INTEGER	read-only	Is this test point at a warning level?
STR bdenvType	1.3.6.1.4.1.3320.2.1.110	DisplayString	read-only	The type of environmental card
INT bdfreeMem	1.3.6.1.4.1.3320.2.1.8	INTEGER	read-only	The freeMem mib object is obsolete as of IOS 11.1 It has been replaced with the BDCom memory pool mib
IP bdhostConfigAddr	1.3.6.1.4.1.3320.2.1.51	IpAddress	read-only	Contains the address of the host that provided the host-config file.
STR bdhostConfigName	1.3.6.1.4.1.3320.2.1.52	DisplayString	read-only	Contains the name of the last configured host-confg file.
INT bdhostConfigProto	1.3.6.1.4.1.3320.2.1.71	INTEGER	read-only	Holds the protocol that supplied the host- confg file.
STR bdhostConfigSet	1.3.6.1.4.1.3320.2.1.53	DisplayString	write-only	Cause the loading of a new host-confg file using TFTP.
STR bdhostName	1.3.6.1.4.1.3320.2.1.3	DisplayString	read-only	This variable represents the name of the host in printable ascii characters.
INT bdidleCount	1.3.6.1.4.1.3320.2.1.59	INTEGER	read-write	BDCom internal variable. not to be used
INT bdidleWired	1.3.6.1.4.1.3320.2.1.60	INTEGER	read-write	BDCom internal variable. not to be used
bdlsystem	1.3.6.1.4.1.3320.2.1
IP bdnetConfigAddr	1.3.6.1.4.1.3320.2.1.48	IpAddress	read-only	Holds the address of the host that supplied the network-confg file.
STR bdnetConfigName	1.3.6.1.4.1.3320.2.1.49	DisplayString	read-only	Holds the name of the network configuration file.
INT bdnetConfigProto	1.3.6.1.4.1.3320.2.1.70	INTEGER	read-only	Holds the protocol that supplied the network-confg file.
STR bdnetConfigSet	1.3.6.1.4.1.3320.2.1.50	DisplayString	write-only	Cause the loading of a new network-confg file using TFTP.
INT bdping	1.3.6.1.4.1.3320.2.1.7	INTEGER	read-write	The ping mib object is obsolete as of IOS 10.2 It has been superseded by the BDCom Ping MIB
STR bdromId	1.3.6.1.4.1.3320.2.1.1	DisplayString	read-only	This variable contains a printable octet string which contains the System Bootstrap description and version identification.
INT bdsysClearARP	1.3.6.1.4.1.3320.2.1.75	INTEGER	write-only	Perform a clearing of the entire ARP cache and invalidation of route caches.
INT bdsysClearInt	1.3.6.1.4.1.3320.2.1.76	INTEGER	write-only	Clear interface given IfIndex as value.
IP bdsysConfigAddr	1.3.6.1.4.1.3320.2.1.72	IpAddress	read-only	Holds the address of the host that supplied the system boot image.
STR bdsysConfigName	1.3.6.1.4.1.3320.2.1.73	DisplayString	read-only	Holds the name of the system boot image.
INT bdsysConfigProto	1.3.6.1.4.1.3320.2.1.74	INTEGER	read-only	Holds the protocol that supplied the system boot image.
STR bdwhyReload	1.3.6.1.4.1.3320.2.1.2	DisplayString	read-only	This variable contains a printable octet string which contains the reason why the system was last restarted.
INT bdwriteMem	1.3.6.1.4.1.3320.2.1.54	INTEGER	write-only	Write configuration into non-volatile memory / erase config memory if 0.
STR bdwriteNet	1.3.6.1.4.1.3320.2.1.55	DisplayString	write-only	Write configuration to host using TFTP.

RFC description

System configuration and status information including bootstrap, hostname, and domain name.

Start monitoring BDCOM networking equipment (switches/routers) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download BDCOM-SYS

What Is BDCOM-SYS?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description