TN-MPLS-TP-MIB

All MIBs › TN-MPLS-TP-MIB

Organization: Nokia

Last Updated: 2015-09-30

Category: MPLS, Nokia Carrier Ethernet

Description: Manages Nokia carrier Ethernet MPLS-TP tunnel configuration and OAM state.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is TN-MPLS-TP-MIB?

TN-MPLS-TP-MIB is a Nokia-proprietary SNMP MIB module for the Nokia SROS platform, used to provision and manage MPLS Transport Profile (MPLS-TP) tunnels and their OAM functions. It exposes configuration and status data for MPLS-TP tunnel identifiers, global/node identifiers, tunnel ID ranges, administrative state, and OAM template configuration used for continuity-check and fault-detection sessions on TP tunnels. Rather than hardware sensors, its monitoring value lies in tunnel/service health — administrative state reveals whether a tunnel is enabled, and configuration change timestamps reveal when tunnel provisioning last changed, both used to catch misconfigured or down transport-layer paths. It is a Nokia-proprietary router MIB built on Nokia's virtual-router ("vRtr") object-naming convention shared across other SROS MIBs, so it depends on that shared numbering/indexing scheme rather than a standards-based IETF MPLS-TP MIB. It is deployed on Nokia SROS-based carrier Ethernet/MPLS-TP routers in service-provider transport networks. Engineers can download the TN-MPLS-TP-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in TN-MPLS-TP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Nokia SROS-based router
carrier Ethernet/MPLS-TP transport router

Monitoring Examples

An admin polls vRtrMplsTpSystemTable/vRtrMplsTpSystemEntry to check vRtrMplsTpGlobalId and vRtrMplsTpNodeId configuration and confirm vRtrMplsTpAdminState shows the MPLS-TP subsystem enabled on a given virtual router. The vRtrMplsTpOamTemplateCfgTable (tracked via vRtrMplsTpOamTemplTblLastChanged) exposes OAM template configuration; a recent, unexpected change timestamp combined with a tunnel outside its configured vRtrMplsTpTunnelIdMin/vRtrMplsTpTunnelIdMax range would indicate a provisioning error.

What Can Be Monitored

MPLS-TP tunnel admin state
global/node ID configuration
tunnel ID range
OAM template configuration
configuration change timestamps

Imported Objects

From IF-MIB

InterfaceIndexOrZero

From INET-ADDRESS-MIB

InetAddress
InetAddressType

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

RowPointer
RowStatus
TEXTUAL-CONVENTION
TimeInterval
TimeStamp
TruthValue

From TN-MPLS-MIB

vRtrMplsLspIndex

From TN-TC-MIB

TItemDescription
TNamedItem
TNamedItemOrEmpty
TmnxAdminState
TmnxEnabledDisabled
TmnxMplsTpGlobalID
TmnxMplsTpNodeID
TmnxMplsTpTunnelType
TmnxOperState
TmnxTunnelID

From TN-VRTR-MIB

vRtrID

OBJECT-TYPE

From TROPIC-GLOBAL-REG

tnSRMIBModules	OBJECT-IDENTITY
tnSRObjs	OBJECT-IDENTITY

From TROPIC-SYSTEM-MIB

tnSysSwitchId

OBJECT-TYPE

How to Use in IPNetwork Monitor

Example using vRtrMplsTpLspPtPathMepWTRTimer OID:

Select a Nokia SROS-based router, carrier Ethernet/MPLS-TP transport router (MPLS-TP tunnel/OAM admin status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type vRtrMplsTpLspPtPathMepWTRTimer into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The value of vRtrMplsTpLspPtPathMepWTRTimer indicates the remaining Wait-To-Restore time, in seconds, before the protection path can switch back to the working path. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the value stays unexpectedly high or low relative to what you'd expect for this timer, since that can indicate a stuck or stale state. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
tnMplsTpMIBModule	1.3.6.1.4.1.7483.5.1.3.83			This document is the SNMP MIB module to manage and provision the MPLS Transport Profile (TP) components of the Nokia SROS. Copyright (c) 2016 Nokia. All rights reserved. Reproduction of this document is authorized on the condition that the foregoing copyright notice is included. This SNMP MIB module (Specification) embodies Nokia's proprietary intellectual property. Nokia retains all title and ownership in the Specification, including any revisions. Nokia grants all interested parties a non-exclusive license to use and distribute an unmodified copy of this Specification in connection with management of Nokia products, and without fee, provided this copyright notice and license appear on all copies. This Specification is supplied 'as is', and Nokia makes no warranty, either express or implied, as to the use, operation, condition, or performance of the Specification.
vRtrMplsTpActions	1.3.6.1.4.1.7483.6.1.2.83.6
TMN vRtrMplsTpAdminState	1.3.6.1.4.1.7483.6.1.2.83.2.1.1.1.6	TmnxAdminState	read-create	The value of vRtrMplsTpAdminState specifies the desired administrative state of MPLS-TP on this router.
vRtrMplsTpCmdObjects	1.3.6.1.4.1.7483.6.1.2.83.2.4
vRtrMplsTpConfigTimeStamps	1.3.6.1.4.1.7483.6.1.2.83.1
vRtrMplsTpConfigurations	1.3.6.1.4.1.7483.6.1.2.83.2
TMN vRtrMplsTpGlobalId	1.3.6.1.4.1.7483.6.1.2.83.2.1.1.1.2	TmnxMplsTpGlobalID	read-create	The value of vRtrMplsTpGlobalId specifies the AS number of the node.
BIT vRtrMplsTpInheritance	1.3.6.1.4.1.7483.6.1.2.83.2.1.1.1.7	Bits	read-create	For each writable object in this row that can be configured to inherit its value from the corresponding object in the vRtrIpAddrTable, there is bit within vRtrMplsTpInheritance that controls whether to inherit the operational value of the object or use the administratively set value. Non mask bits will always have value of zero. This object is a bit-mask, with the following objects: vRtrMplsTpNodeId 0x1 When the bit for an object is set to one, then the object's administrative and operational value are inherited from the corresponding object in vRtrIpAddrTable. When the bit for an object is set to zero, then the object's administrative and operational value are whatever the DEFVAL or most recently SET value is.
vRtrMplsTpLspObjects	1.3.6.1.4.1.7483.6.1.2.83.2.3
NUM vRtrMplsTpLspPathActiveTimeUp	1.3.6.1.4.1.7483.6.1.2.83.2.3.2.1.16	TimeInterval	read-only	The value of vRtrMplsTpLspPathActiveTimeUp indicates the time that this MPLS-TP LSP Path has been active.
TMN vRtrMplsTpLspPathAdminState	1.3.6.1.4.1.7483.6.1.2.83.2.3.2.1.4	TmnxAdminState	read-create	The value of vRtrMplsTpLspPathAdminState specifies the administrative state of the MPLS-TP LSP Path.
vRtrMplsTpLspPathEntry	1.3.6.1.4.1.7483.6.1.2.83.2.3.2.1		not-accessible	The vRtrMplsTpLspPathEntry contains the configuration objects for the MPLS-TP path table.
INT vRtrMplsTpLspPathIndex	1.3.6.1.4.1.7483.6.1.2.83.2.3.2.1.1	INTEGER	not-accessible	The value of vRtrMplsTpLspPathIndex specifies the path index for the MPLS-TP LSP path. working (1) - A working path is the primary path for the LSP. protecting (2) - A protection path is the secondary path for the LSP.
U32 vRtrMplsTpLspPathInLabel	1.3.6.1.4.1.7483.6.1.2.83.2.3.2.1.8	Unsigned32	read-create	The value of vRtrMplsTpLspPathInLabel specifies the LSP ingress Label used by the MPLS-TP LSP Path. Once this object is set, to remove the in-label, one must destroy and recreate the vRtrMplsTpLspPathEntry.
TIM vRtrMplsTpLspPathLastChangedTime	1.3.6.1.4.1.7483.6.1.2.83.2.3.2.1.3	TimeStamp	read-only	The value of vRtrMplsTpLspPathLastChangedTime indicates the last time, since system startup, that a writable object in this table was modified.
U32 vRtrMplsTpLspPathLspNumber	1.3.6.1.4.1.7483.6.1.2.83.2.3.2.1.7	Unsigned32	read-create	The value of vRtrMplsTpLspPathLspNumber specifies the MPLS-TP LSP Path number. The default value of this object is dependent on the value of vRtrMplsTpLspPathIndex. If this object refers to a 'working (1)' path, then the default value is one (1). If this object refers to a 'protecting (2)' path, then the default value is two (2).
TMN vRtrMplsTpLspPathMepAdminState	1.3.6.1.4.1.7483.6.1.2.83.2.3.3.1.3	TmnxAdminState	read-create	The value of vRtrMplsTpLspPathMepAdminState specifies the administrative state of the MPLS-TP LSP path.
INT vRtrMplsTpLspPathMepBfdEnabled	1.3.6.1.4.1.7483.6.1.2.83.2.3.3.1.6	INTEGER	read-create	The value of vRtrMplsTpLspPathMepBfdEnabled specifies whether BFD is enabled or not. If set to 'disabled (0)', BFD is not enabled. If set to 'cc (1)', BFD is enabled with Continuity Check (CC) functionality. If set to 'ccCv (2)', BFD is enabled with both CC and Connectivity Verification (CV) functionality. In this mode, BFD will detect mis-connectivity as described in RFC 6428 Section 3.7.2. Once enabled, a modification to this object will effect the BFD session.
TMN vRtrMplsTpLspPathMepBfdOperState	1.3.6.1.4.1.7483.6.1.2.83.2.3.3.1.7	TmnxOperState	read-only	The value of vRtrMplsTpLspPathMepBfdOperState indicates the operational state of the BFD session. The operational state of 'unknown (1)' indicates that the BFD session is not enabled.
vRtrMplsTpLspPathMepEntry	1.3.6.1.4.1.7483.6.1.2.83.2.3.3.1		not-accessible	The vRtrMplsTpLspPathMepEntry represents a Maintenance Endpoint for a MPLS-TP LSP Path.
TIM vRtrMplsTpLspPathMepLastChgTime	1.3.6.1.4.1.7483.6.1.2.83.2.3.3.1.1	TimeStamp	read-only	The value of vRtrMplsTpLspPathMepLastChgTime indicates the time, since system startup, when a columnar object for the specified row last changed state.
TNA vRtrMplsTpLspPathMepOamTmpl	1.3.6.1.4.1.7483.6.1.2.83.2.3.3.1.5	TNamedItemOrEmpty	read-create	The value of vRtrMplsTpLspPathMepOamTmpl specifies the associated vRtrMplsTpOamTemplateCfgEntry to this MPLS-TP LSP Path MEP.
TNA vRtrMplsTpLspPathMepProtectTmpl	1.3.6.1.4.1.7483.6.1.2.83.2.3.3.1.4	TNamedItemOrEmpty	read-create	The value of vRtrMplsTpLspPathMepProtectTmpl specifies the associated vRtrMplsTpPtcTemplateCfgEntry to this MPLS-TP LSP Path MEP. This object is only meaningful to the row indexed with the vRtrMplsTpLspPathIndex value of 'protecting'. Attempts to configure this object, otherwise, will result in an 'inconsistentValue' error.
ROW vRtrMplsTpLspPathMepRowStatus	1.3.6.1.4.1.7483.6.1.2.83.2.3.3.1.2	RowStatus	read-create	The value of vRtrMplsTpLspPathMepRowStatus specifies the row status of the vRtrMplsTpLspPathMepEntry.
vRtrMplsTpLspPathMepTable	1.3.6.1.4.1.7483.6.1.2.83.2.3.3		not-accessible	The vRtrMplsTpLspPathMepTable maintains the Maintenance End Points (MEPs) for the MPLS-TP LSP path.
TIM vRtrMplsTpLspPathMepTblLastChg	1.3.6.1.4.1.7483.6.1.2.83.1.6	TimeStamp	read-only	The value of vRtrMplsTpLspPathMepTblLastChg indicates the last time, since system startup, that the vRtrMplsTpLspPathMepTable changed state.
IP vRtrMplsTpLspPathNextHopAddress	1.3.6.1.4.1.7483.6.1.2.83.2.3.2.1.12	InetAddress	read-create	The value of vRtrMplsTpLspPathNextHopAddress, along with vRtrMplsTpLspPathNextHopAddrType, specifies the IP address used as the next hop for the MPLS-TP LSP Path. Once this object is set, to remove the next hop, one must destroy and recreate the vRtrMplsTpLspPathEntry. This object is only applicable if the vRtrMplsTpLspPathOutLink references a numbered interface.
IPt vRtrMplsTpLspPathNextHopAddrType	1.3.6.1.4.1.7483.6.1.2.83.2.3.2.1.11	InetAddressType	read-create	The value of vRtrMplsTpLspPathNextHopAddrType, along with vRtrMplsTpLspPathNextHopAddress, specifies the IP address used as the next hop for the MPLS-TP LSP Path. Once this object is set, to remove the next hop, one must destroy and recreate the vRtrMplsTpLspPathEntry. This object is only applicable if the vRtrMplsTpLspPathOutLink references a numbered interface.
TMN vRtrMplsTpLspPathOperState	1.3.6.1.4.1.7483.6.1.2.83.2.3.2.1.5	TmnxOperState	read-only	The value of vRtrMplsTpLspPathOperState indicates the operational state of the MPLS-TP LSP Path.
U32 vRtrMplsTpLspPathOutLabel	1.3.6.1.4.1.7483.6.1.2.83.2.3.2.1.9	Unsigned32	read-create	The value of vRtrMplsTpLspPathOutLabel specifies the LSP egress Label used by the MPLS-TP LSP Path. Once this object is set, to remove the out-label, one must destroy and recreate the vRtrMplsTpLspPathEntry.
NUM vRtrMplsTpLspPathOutLink	1.3.6.1.4.1.7483.6.1.2.83.2.3.2.1.10	InterfaceIndexOrZero	read-create	The value of vRtrMplsTpLspPathOutLink specifies the LSP out-link interface used by the MPLS-TP LSP Path. Once this object is set, to remove the out-link, one must destroy and recreate the vRtrMplsTpLspPathEntry.
BIT vRtrMplsTpLspPathReasonDownFlags	1.3.6.1.4.1.7483.6.1.2.83.2.3.2.1.6	Bits	read-only	The value of vRtrMplsTpLspPathReasonDownFlags specifies the reason why the MPLS-TP LSP Path is operationally down when the administrative state is 'inService (2)'. The recognized BIT values are: unknown (0) - Unspecified (or unknown) ccFault (1) - BFD Continuity Check (CC) failed cvFault (2) - BFD Connectivity Verification (CV) failed ifDn (3) - The path out-link interface is operationally down portDn (4) - The port associated with the out-link interface is operationally down parentAdminDn (5) - The associated mpls-tp Lsp or mpls-tp instance or mpls instance is admin down mepAdminDn (6) - The path MEP is admin down unsupportedPort (7) - MPLS-TP functionality is not supported over the out-link port. ifNhAddrInconsistent (8) - The configured next-hop address is not bound to the configured out-link interface. ptcTmplMsng (9) - The protect-tp-path is missing a protection-template name. ccDnHold (10) - ccFault effect on path-state is on hold due to 'hold-time-down' config in the oam-template ccUpHold (11) - ccFault clear effect on path-state is on hold due to 'hold-time-up' config in the oam-template bfdNoRsrc (12) - bfd-enable failed since maximum number of supported bfd-sessions was reached.
ROW vRtrMplsTpLspPathRowStatus	1.3.6.1.4.1.7483.6.1.2.83.2.3.2.1.2	RowStatus	read-create	The value of vRtrMplsTpLspPathRowStatus specifies the row status of the MPLS-TP LSP Path.
INT vRtrMplsTpLspPathState	1.3.6.1.4.1.7483.6.1.2.83.2.3.2.1.13	INTEGER	read-only	The value of vRtrMplsTpLspPathState indicates the current working state of the MPLS-TP LSP Path.
vRtrMplsTpLspPathTable	1.3.6.1.4.1.7483.6.1.2.83.2.3.2		not-accessible	The vRtrMplsTpLspPathTable maintains the MPLS-TP configuration objects associated with an MPLS LSP path.
TIM vRtrMplsTpLspPathTblLastChanged	1.3.6.1.4.1.7483.6.1.2.83.1.5	TimeStamp	read-only	The value of vRtrMplsTpLspPathTblLastChanged indicates the last time, since system startup, that the vRtrMplsTpLspPathTable changed state.
NUM vRtrMplsTpLspPathTimeDown	1.3.6.1.4.1.7483.6.1.2.83.2.3.2.1.15	TimeInterval	read-only	The value of vRtrMplsTpLspPathTimeDown indicates the time that this MPLS-TP LSP Path has not been operational.
NUM vRtrMplsTpLspPathTimeUp	1.3.6.1.4.1.7483.6.1.2.83.2.3.2.1.14	TimeInterval	read-only	The value of vRtrMplsTpLspPathTimeUp indicates the time that this MPLS-TP LSP path has been operational.
BIT vRtrMplsTpLspPtPathMepDefects	1.3.6.1.4.1.7483.6.1.2.83.2.3.4.1.3	Bits	read-only	The value of vRtrMplsTpLspPtPathMepDefects indicates the defect state of the protection path MEP. The defects monitored by this object are as follows: - protectionTypeMismatch (0) - A protection-type mismatch is detected. - revertModeMismatch (1) - A revertive mode mismatch is detected.
VRT vRtrMplsTpLspPtPathMepRxPdu	1.3.6.1.4.1.7483.6.1.2.83.2.3.4.1.1	VRtrMplsTpLspPathMepPduType	read-only	The value of vRtrMplsTpLspPtPathMepRxPdu indicates the last received PSC PDU APS format. The value of this object compared to that of vRtrMplsTpLspPtPathMepTxPdu will indicate a configuration mismatch between the local and far-end node.
vRtrMplsTpLspPtPathMepStatEntry	1.3.6.1.4.1.7483.6.1.2.83.2.3.4.1		not-accessible	The vRtrMplsTpLspPathMepEntry represents a Maintenance Endpoint for a MPLS-TP LSP protection Path. Rows are created and destroyed by the system based on the configuration of the MEP protection-type.
vRtrMplsTpLspPtPathMepStatTable	1.3.6.1.4.1.7483.6.1.2.83.2.3.4		not-accessible	The vRtrMplsTpLspPtPathMepStatTable maintains the Maintenance End Points (MEPs) statistics for MPLS-TP LSP protection paths.
VRT vRtrMplsTpLspPtPathMepTxPdu	1.3.6.1.4.1.7483.6.1.2.83.2.3.4.1.2	VRtrMplsTpLspPathMepPduType	read-only	The value of vRtrMplsTpLspPtPathMepTxPdu indicates the last transmitted PSC PDU APS format. The value of this object compared to that of vRtrMplsTpLspPtPathMepRxPdu will indicate a configuration mismatch between the local and far-end node.
C32 vRtrMplsTpLspPtPathMepWTRTimerEx	1.3.6.1.4.1.7483.6.1.2.83.2.3.4.1.4	Counter32	read-only	The value of vRtrMplsTpLspPtPathMepWTRTimer indicates the remaining Wait-To-Restore time, in seconds, before the protection path can switch back to the working path. A value of zero (0) indicates that there is no WTR timer in effect.
TMN vRtrMplsTpLsrAdminState	1.3.6.1.4.1.7483.6.1.2.83.2.5.1.1.4	TmnxAdminState	read-create	The value of vRtrMplsTpLsrAdminState specifies the administrative state of the MPLS-TP LSR.
vRtrMplsTpLsrCfgEntry	1.3.6.1.4.1.7483.6.1.2.83.2.5.1.1		not-accessible	The vRtrMplsTpLsrCfgEntry contains the configuration items maintained by the vRtrMplsTpLsrCfgTable.
vRtrMplsTpLsrCfgTable	1.3.6.1.4.1.7483.6.1.2.83.2.5.1		not-accessible	The vRtrMplsTpLsrCfgTable maintains the MPLS-TP LSR configuration information.
T/F vRtrMplsTpLsrFPEnabled	1.3.6.1.4.1.7483.6.1.2.83.2.5.1.1.16	TruthValue	read-create	The value of vRtrMplsTpLsrFPEnabled specifies whether the forward path is configured for the LSR path.
U32 vRtrMplsTpLsrFPInLabel	1.3.6.1.4.1.7483.6.1.2.83.2.5.1.1.6	Unsigned32	read-create	The value of vRtrMplsTpLsrFPInLabel specifies the forward path (FP) ingress label used by the MPLS-TP LSR Path. This object can be set only after vRtrMplsTpLsrFPEnabled is set to 'true'. Once this object is set, the value may not be unset. To remove the ingress label one must set vRtrMplsTpLsrFPEnabled to 'false'.
IP vRtrMplsTpLsrFPNextHopAddress	1.3.6.1.4.1.7483.6.1.2.83.2.5.1.1.10	InetAddress	read-create	The value of vRtrMplsTpLsrFPNextHopAddress, along with vRtrMplsTpLsrFPNextHopAddrType, specifies the forward path (FP) IP address used as the next hop for the MPLS-TP LSR Path. This object can be set only after vRtrMplsTpLsrFPEnabled is set to 'true'. Once this object is set, the value may not be unset. To remove the next hop, one must set vRtrMplsTpLsrFPEnabled to 'false'. This object is only applicable if the vRtrMplsTpLsrFPOutLink references a numbered interface.
IPt vRtrMplsTpLsrFPNextHopAddrType	1.3.6.1.4.1.7483.6.1.2.83.2.5.1.1.9	InetAddressType	read-create	The value of vRtrMplsTpLsrFPNextHopAddrType, along with vRtrMplsTpLsrFPNextHopAddress, specifies the forward path (FP) IP address used as the next hop for the MPLS-TP LSP Path. This object can be set only after vRtrMplsTpLsrFPEnabled is set to 'true'. Once this object is set, the value may not be unset. To remove the next hop, one must set vRtrMplsTpLsrFPEnabled to 'false'. This object is only applicable if the vRtrMplsTpLsrFPOutLink references a numbered interface.
U32 vRtrMplsTpLsrFPOutLabel	1.3.6.1.4.1.7483.6.1.2.83.2.5.1.1.7	Unsigned32	read-create	The value of vRtrMplsTpLsrFPOutLabel specifies the forward path (FP) egress label used by the MPLS-TP LSR Path. This object can be set only after vRtrMplsTpLsrFPEnabled is set to 'true'. Once this object is set, the value may not be unset. To remove the egress label one must set vRtrMplsTpLsrFPEnabled to 'false'.
NUM vRtrMplsTpLsrFPOutLink	1.3.6.1.4.1.7483.6.1.2.83.2.5.1.1.8	InterfaceIndexOrZero	read-create	The value of vRtrMplsTpLsrFPOutLink specifies the forward path (FP) out-link interface used by the MPLS-TP LSR Path. This object can be set only after vRtrMplsTpLsrFPEnabled is set to 'true'. Once this object is set, the value may not be unset. To remove the out-link, one must set vRtrMplsTpLsrFPEnabled to 'false'.
TIM vRtrMplsTpLsrLastChangedTime	1.3.6.1.4.1.7483.6.1.2.83.2.5.1.1.3	TimeStamp	read-only	The value of vRtrMplsTpLsrLastChangedTime indicates the time, since system startup, that a columnar object in the MPLS-TP LSR entry last changed state.
vRtrMplsTpLsrObjects	1.3.6.1.4.1.7483.6.1.2.83.2.5
TMN vRtrMplsTpLsrOperState	1.3.6.1.4.1.7483.6.1.2.83.2.5.1.1.5	TmnxOperState	read-only	The value of vRtrMplsTpLsrOperState indicates the operational state of the MPLS-TP LSR.
TMN vRtrMplsTpLsrPathIdDestGlobalId	1.3.6.1.4.1.7483.6.1.2.83.2.5.3.1.4	TmnxMplsTpGlobalID	not-accessible	The value of vRtrMplsTpLsrPathIdDestGlobalId specifies the unique node identifier for the given remote global ID.
TMN vRtrMplsTpLsrPathIdDestNodeId	1.3.6.1.4.1.7483.6.1.2.83.2.5.3.1.5	TmnxMplsTpNodeID	not-accessible	The value of vRtrMplsTpLsrPathIdDestNodeId specifies the unique node identifier for the given remote node ID.
U32 vRtrMplsTpLsrPathIdDestTunNum	1.3.6.1.4.1.7483.6.1.2.83.2.5.3.1.6	Unsigned32	not-accessible	The value of vRtrMplsTpLsrPathIdDestTunNum specifies the destination tunnel number of an MPLS-TP Static LSP.
vRtrMplsTpLsrPathIdEntry	1.3.6.1.4.1.7483.6.1.2.83.2.5.3.1		not-accessible	The vRtrMplsTpLsrPathIdEntry contains the configuration items maintained by the vRtrMplsTpLsrPathIdTable.
U32 vRtrMplsTpLsrPathIdLspNumber	1.3.6.1.4.1.7483.6.1.2.83.2.5.3.1.7	Unsigned32	not-accessible	The value of vRtrMplsTpLsrPathIdLspNumber specifies the MPLS-TP LSP Path number.
TNA vRtrMplsTpLsrPathIdPathName	1.3.6.1.4.1.7483.6.1.2.83.2.5.3.1.9	TNamedItem	read-create	The value of vRtrMplsTpLsrPathIdPathName specifies the unique name of the MPLS-TP LSR Path. This object MUST be specified on row-creation, and must reference an existing vRtrMplsTpLsrPathName.
ROW vRtrMplsTpLsrPathIdRowStatus	1.3.6.1.4.1.7483.6.1.2.83.2.5.3.1.8	RowStatus	read-create	The value of vRtrMplsTpLsrPathIdRowStatus specifies the row status of the MPLS-TP LSR Path. Rows are created by setting this object to the value 'createAndGo (4)' and are destroyed by using the value 'destroy (6)'.
TMN vRtrMplsTpLsrPathIdSrcGlobalId	1.3.6.1.4.1.7483.6.1.2.83.2.5.3.1.1	TmnxMplsTpGlobalID	not-accessible	The value of vRtrMplsTpLsrPathIdSrcGlobalId specifies the unique node identifier for the given source global ID.
TMN vRtrMplsTpLsrPathIdSrcNodeId	1.3.6.1.4.1.7483.6.1.2.83.2.5.3.1.2	TmnxMplsTpNodeID	not-accessible	The value of vRtrMplsTpLsrPathIdSrcNodeId specifies the unique node identifier for the given source node ID.
U32 vRtrMplsTpLsrPathIdSrcTunNum	1.3.6.1.4.1.7483.6.1.2.83.2.5.3.1.3	Unsigned32	not-accessible	The value of vRtrMplsTpLsrPathIdSrcTunNum specifies the source tunnel number of an MPLS-TP Static LSP.
vRtrMplsTpLsrPathIdTable	1.3.6.1.4.1.7483.6.1.2.83.2.5.3		not-accessible	The vRtrMplsTpLsrPathIdTable maintains the MPLS-TP LSR Path configuration information.
TIM vRtrMplsTpLsrPathIdTblLastChg	1.3.6.1.4.1.7483.6.1.2.83.1.8	TimeStamp	read-only	The value of vRtrMplsTpLsrPathIdTblLastChg indicates the last time, since system startup, when the vRtrMplsTpLsrPathIdTable changed state.
TNA vRtrMplsTpLsrPathName	1.3.6.1.4.1.7483.6.1.2.83.2.5.1.1.1	TNamedItem	not-accessible	The value of vRtrMplsTpLsrPathName specifies the unique name of the MPLS-TP LSR Path.
ROW vRtrMplsTpLsrRowStatus	1.3.6.1.4.1.7483.6.1.2.83.2.5.1.1.2	RowStatus	read-create	The value of vRtrMplsTpLsrRowStatus specifies the row status of the MPLS-TP LSR configuration entry. Rows are created by setting this object to the value 'createAndGo (4)' and are destroyed by using the value 'destroy (6)'.
T/F vRtrMplsTpLsrRPEnabled	1.3.6.1.4.1.7483.6.1.2.83.2.5.1.1.17	TruthValue	read-create	The value of vRtrMplsTpLsrRPEnabled specifies whether the reverse path is configured for the LSR path.
U32 vRtrMplsTpLsrRPInLabel	1.3.6.1.4.1.7483.6.1.2.83.2.5.1.1.11	Unsigned32	read-create	The value of vRtrMplsTpLsrRPInLabel specifies the reverse path (RP) LSP ingress label used by the MPLS-TP LSR Path. This object can be set only after vRtrMplsTpLsrRPEnabled is set to 'true'. Once this object is set, the value may not be unset. To remove the ingress label, one must set vRtrMplsTpLsrRPEnabled to 'false'.
IP vRtrMplsTpLsrRPNextHopAddress	1.3.6.1.4.1.7483.6.1.2.83.2.5.1.1.15	InetAddress	read-create	The value of vRtrMplsTpLsrRPNextHopAddress, along with vRtrMplsTpLsrRPNextHopAddrType, specifies the reverse path (RP) IP address used as the next hop for the MPLS-TP LSR Path. This object can be set only after vRtrMplsTpLsrRPEnabled is set to 'true'. Once this object is set, this value may not be unset. To remove the next hop, one must set vRtrMplsTpLsrRPEnabled to 'false'. This object is only applicable if the vRtrMplsTpLsrRPOutLink references a numbered interface.
IPt vRtrMplsTpLsrRPNextHopAddrType	1.3.6.1.4.1.7483.6.1.2.83.2.5.1.1.14	InetAddressType	read-create	The value of vRtrMplsTpLsrRPNextHopAddrType, along with vRtrMplsTpLsrRPNextHopAddress, specifies the reverse path (RP) IP address used as the next hop for the MPLS-TP LSP Path. This object can be set only after vRtrMplsTpLsrRPEnabled is set to 'true'. Once this object is set, this value may not be unset. To remove the next hop, one must set vRtrMplsTpLsrRPEnabled to 'false'. This object is only applicable if the vRtrMplsTpLsrRPOutLink references a numbered interface.
U32 vRtrMplsTpLsrRPOutLabel	1.3.6.1.4.1.7483.6.1.2.83.2.5.1.1.12	Unsigned32	read-create	The value of vRtrMplsTpLsrRPOutLabel specifies the reverse path (RP) LSP egress label used by the MPLS-TP LSR Path. This object can be set only after vRtrMplsTpLsrRPEnabled is set to 'true'. Once this object is set, this value may not be unset. To remove the egress label, one must set vRtrMplsTpLsrFPEnabled to 'false'.
NUM vRtrMplsTpLsrRPOutLink	1.3.6.1.4.1.7483.6.1.2.83.2.5.1.1.13	InterfaceIndexOrZero	read-create	The value of vRtrMplsTpLsrRPOutLink specifies the reverse path (RP) LSP out-link interface used by the MPLS-TP LSP Path. This object can be set only after vRtrMplsTpLsrRPEnabled is set to 'true'. Once this object is set, this value may not be unset. To remove the out-link, one must set vRtrMplsTpLsrRPEnabled to 'false'.
TIM vRtrMplsTpLsrTblLastChanged	1.3.6.1.4.1.7483.6.1.2.83.1.7	TimeStamp	read-only	The value of vRtrMplsTpLsrTblLastChanged indicates the last time, since system startup, when the vRtrMplsTpLsrCfgTable changed state.
TMN vRtrMplsTpNodeId	1.3.6.1.4.1.7483.6.1.2.83.2.1.1.1.3	TmnxMplsTpNodeID	read-create	The value of vRtrMplsTpNodeId specifies the unique node identifier for the given global ID. If not specified, the MPLS Router ID of the node is used.
vRtrMplsTpNotifyObjects	1.3.6.1.4.1.7483.6.1.2.83.10
vRtrMplsTpOamTemplateCfgEntry	1.3.6.1.4.1.7483.6.1.2.83.2.2.1.1		not-accessible	The vRtrMplsTpOamTemplateCfgEntry contains the configuration items maintained by the vRtrMplsTpOamTemplateCfgTable.
vRtrMplsTpOamTemplateCfgTable	1.3.6.1.4.1.7483.6.1.2.83.2.2.1		not-accessible	The vRtrMplsTpOamTemplateCfgTable maintains the MPLS-TP Templates used by MPLS-TP OAM. The template is specific to the OAM protocol and can be used to configure MPLS-TP-OAM parameters such as BFD Tx/Rx timer intervals, multiplier and any other relevant session/fault management parameters. The OAM template is referenced in the MPLS-TP path configuration, so different values are possible for the working and protect paths of a tunnel.
TIM vRtrMplsTpOamTemplTblLastChanged	1.3.6.1.4.1.7483.6.1.2.83.1.2	TimeStamp	read-only	The value of vRtrMplsTpOamTemplTblLastChanged indicates the last time, since system startup, when the vRtrMplsTpOamTemplateCfgTable last changed state.
TNA vRtrMplsTpOamTmplBfdTemplateName	1.3.6.1.4.1.7483.6.1.2.83.2.2.1.1.4	TNamedItemOrEmpty	read-create	The value of vRtrMplsTpOamTmplBfdTemplateName specifies the TIMETRA-BFD-MIB::tmnxBfdAdminTemplateName used by the OAM template.
U32 vRtrMplsTpOamTmplHoldTimeDown	1.3.6.1.4.1.7483.6.1.2.83.2.2.1.1.5	Unsigned32	read-create	The value of vRtrMplsTpOamTmplHoldTimeDown specifies the time, in centiseconds, used for the hold-timer for the BFD Continuity Check (CC) session down event dampening. This guards against reporting excessive operational state transitions. This is implemented by not advertising subsequent transitions of the BFD CC state until the configured timer has expired. A value of zero (0) specifies that a down transition is reported immediately.
U32 vRtrMplsTpOamTmplHoldTimeUp	1.3.6.1.4.1.7483.6.1.2.83.2.2.1.1.6	Unsigned32	read-create	The value of vRtrMplsTpOamTmplHoldTimeUp specifies the time, in deciseconds, used for the hold-timer for the BFD Continuity Check (CC) session up event dampening. This guards against reporting excessive operational state transitions. This is implemented by not advertising subsequent transitions of the BFD CC state until the configured timer has expired. A value of zero (0) specifies that an up transition is reported immediately.
TIM vRtrMplsTpOamTmplLastChangedTime	1.3.6.1.4.1.7483.6.1.2.83.2.2.1.1.3	TimeStamp	read-only	The value vRtrMplsTpOamTmplLastChangedTime indicates the time, since system startup, that an columnar object in this row changed state.
TNA vRtrMplsTpOamTmplName	1.3.6.1.4.1.7483.6.1.2.83.2.2.1.1.1	TNamedItem	not-accessible	The value vRtrMplsTpOamTmplName specifies the unique name of the MPLS-TP OAM Template.
ROW vRtrMplsTpOamTmplRowStatus	1.3.6.1.4.1.7483.6.1.2.83.2.2.1.1.2	RowStatus	read-create	The value of vRtrMplsTpOamTmplRowStatus specifies the row status of the MPLS-TP OAM Template entry. Rows are created by setting this object to the value 'createAndGo (4)' and are destroyed using the value 'destroy (6)'.
vRtrMplsTpObjs	1.3.6.1.4.1.7483.6.1.2.83
vRtrMplsTpPtcTemplateCfgEntry	1.3.6.1.4.1.7483.6.1.2.83.2.2.2.1		not-accessible	The vRtrMplsTpPtcTemplateCfgEntry contains the configuration items maintained by the vRtrMplsTpPtcTemplateCfgTable.
vRtrMplsTpPtcTemplateCfgTable	1.3.6.1.4.1.7483.6.1.2.83.2.2.2		not-accessible	The vRtrMplsTpPtcTemplateCfgTable maintains the MPLS-TP Templates used for MPLS LSP Protection. Entries in this table maintain the common configuration elements used by the protected LSPs.
TIM vRtrMplsTpPtcTemplTblLastChanged	1.3.6.1.4.1.7483.6.1.2.83.1.3	TimeStamp	read-only	The value of vRtrMplsTpPtcTemplTblLastChanged indicates the last time, since system startup, when the vRtrMplsTpPtcTemplateCfgTable changed state.
TIM vRtrMplsTpPtcTmplLastChangedTime	1.3.6.1.4.1.7483.6.1.2.83.2.2.2.1.3	TimeStamp	read-only	The value of vRtrMplsTpPtcTmplLastChangedTime indicates the time, since system startup, that a columnar object in the MPLS-TP Protection Template entry last changed state.
TNA vRtrMplsTpPtcTmplName	1.3.6.1.4.1.7483.6.1.2.83.2.2.2.1.1	TNamedItem	not-accessible	The value of vRtrMplsTpPtcTmplName specifies the unique name of the MPLS-TP Protection Template.
INT vRtrMplsTpPtcTmplProtectionDir	1.3.6.1.4.1.7483.6.1.2.83.2.2.2.1.5	INTEGER	read-create	The value of vRtrMplsTpPtcTmplProtectionDir specifies the directional mode of the Protection Template. bidirectional - provides protection in both directions.
INT vRtrMplsTpPtcTmplProtectionMode	1.3.6.1.4.1.7483.6.1.2.83.2.2.2.1.4	INTEGER	read-create	The value of vRtrMplsTpPtcTmplProtectionMode specifies the mode used for determining which members are actively receiving and transmitting data. In the 'one2one (1)' (1:1) architecture, a protection transport path is dedicated to the working transport path of a single service, and the traffic is only transmitted on either the working or the protection path, by using a selector at the source of the protection domain. A selector at the sink of the protection domain then selects the path that carries the normal traffic. When the value is set to 'one2one (1)', only two members are allowed, and only one of them can be active at one point in time.
U32 vRtrMplsTpPtcTmplRapidPscTimer	1.3.6.1.4.1.7483.6.1.2.83.2.2.2.1.8	Unsigned32	read-create	The value of vRtrMplsTpPtcTmplRapidPscTimer specifies the time, in milliseconds, for the Rapid Protection Switch Coordination (PSC) timer. A value of 3 denotes 3.33 ms. When the protection domain state is changed, three PSC messages are transmitted as quickly as possible, to allow for rapid protection switching.
INT vRtrMplsTpPtcTmplRevertive	1.3.6.1.4.1.7483.6.1.2.83.2.2.2.1.6	INTEGER	read-create	The value of vRtrMplsTpPtcTmplRevertive specifies whether or not an instance of this Template will operate in a 'revertive (2)' or 'nonRevertive (1)' mode.
ROW vRtrMplsTpPtcTmplRowStatus	1.3.6.1.4.1.7483.6.1.2.83.2.2.2.1.2	RowStatus	read-create	The value of vRtrMplsTpPtcTmplRowStatus specifies the row status of the MPLS-TP Protection Template. Rows are created by setting this object to the value 'createAndGo (4)' and are destroyed by using the value 'destroy (6)'.
U32 vRtrMplsTpPtcTmplSlowPscTimer	1.3.6.1.4.1.7483.6.1.2.83.2.2.2.1.9	Unsigned32	read-create	The value of vRtrMplsTpPtcTmplSlowPscTimer specifies the time, in seconds, for the Slow Protection Switch Coordination (PSC) timer used to continually transmit the PSC message.
U32 vRtrMplsTpPtcTmplWaitToRestore	1.3.6.1.4.1.7483.6.1.2.83.2.2.2.1.7	Unsigned32	read-create	The value of vRtrMplsTpPtcTmplWaitToRestore specifies the Wait-To-Restore (WTR) timer, in seconds, after a cleared failure the working path must wait before reverting. The WTR timer is used to prevent frequent operation of the protection switching due to intermittent signal failure defects.
ROW vRtrMplsTpRowStatus	1.3.6.1.4.1.7483.6.1.2.83.2.1.1.1.1	RowStatus	read-create	The value of vRtrMplsTpRowStatus specifies the row status of the MPLS-TP system entry. A row must exist in this table for a specified virtual router ID for MPLS-TP LSP configuration to be allowed.
U32 vRtrMplsTpScalar1	1.3.6.1.4.1.7483.6.1.2.83.1.101	Unsigned32	read-only	A dummy scalar that satisfies a SNMP get request quickly.Otherwise, it has to traverse the remaining MIB to get to the next applicable item.
U32 vRtrMplsTpScalar2	1.3.6.1.4.1.7483.6.1.2.83.1.102	Unsigned32	read-only
vRtrMplsTpStatistics	1.3.6.1.4.1.7483.6.1.2.83.5
vRtrMplsTpStatus	1.3.6.1.4.1.7483.6.1.2.83.3
vRtrMplsTpStatusObjects	1.3.6.1.4.1.7483.6.1.2.83.3.1
vRtrMplsTpSystemEntry	1.3.6.1.4.1.7483.6.1.2.83.2.1.1.1		not-accessible	The vRtrMplsTpSystemEntry contains the globally unique configuration objects for MPLS-TP.
vRtrMplsTpSystemIdentifiers	1.3.6.1.4.1.7483.6.1.2.83.2.1
vRtrMplsTpSystemTable	1.3.6.1.4.1.7483.6.1.2.83.2.1.1		not-accessible	The vRtrMplsTpSystemTable consists of the globally unique configuration objects for MPLS-TP. These objects are typically required to be set prior to configuring MPLS-TP LSP objects.
TIM vRtrMplsTpSystemTableLastChanged	1.3.6.1.4.1.7483.6.1.2.83.1.1	TimeStamp	read-only	The value of vRtrMplsTpSystemTableLastChanged indicates the time, since system startup, when the vRtrMplsTpSystemTable last changed state.
vRtrMplsTpTemplateObjects	1.3.6.1.4.1.7483.6.1.2.83.2.2
I32 vRtrMplsTpTunnelAge	1.3.6.1.4.1.7483.6.1.2.83.3.1.1.1.9	Integer32	read-only	The value of vRtrMplsTpTunnelAge indicates the number of seconds since this tunnel entry was last updated or otherwise determined to be correct. No semantics of 'too old' can be implied except through knowledge of owner of the tunnel.
vRtrMplsTpTunnelCommandEntry	1.3.6.1.4.1.7483.6.1.2.83.2.4.1.1		not-accessible	The vRtrMplsTpTunnelCommandEntry contains the command available to execute on an existing MPLS-TP Tunnel. Rows in this table are created and destroyed by the system.
INT vRtrMplsTpTunnelCommandSwitch	1.3.6.1.4.1.7483.6.1.2.83.2.4.1.1.1	INTEGER	read-create	The value vRtrMplsTpTunnelCommandSwitch specifies the switch command to initiate on a MPLS-TP LSP Tunnel. When read, this object returns the last command written or 'noCmd (0)' if no command has been written to this MPLS-TP LSP Tunnel since initialization. The return of the last command written does not imply that this command is currently in effect. This request may be preempted by a higher priority local or remote request. The value 'noCmd (0)' may not be used in a write command. The value 'clear (1)' clears all the switch commands listed below for the specified LSP. The value of 'forceSwitch (2)' switches the active path to the protection path. The value of 'manualSwitch (3)' switches the active path to the protection path. The value of 'lockout (4)' prevents the working path from switching to the protection path.
vRtrMplsTpTunnelCommandTable	1.3.6.1.4.1.7483.6.1.2.83.2.4.1		not-accessible	The vRtrMplsTpTunnelCommandTable maintains the one-shot action commands that effect the state of the MPLS-TP operation.
vRtrMplsTpTunnelEntry	1.3.6.1.4.1.7483.6.1.2.83.3.1.1.1		not-accessible	vRtrMplsTpTunnelEntry defines a tunnel to a particular destination in a specific router context. A tunnel to a specific destination is an MPLS-TP Static LSP.
TMN vRtrMplsTpTunnelGlobalId	1.3.6.1.4.1.7483.6.1.2.83.3.1.1.1.2	TmnxMplsTpGlobalID	not-accessible	vRtrMplsTpTunnelGlobalId indicates the global id of the system.
TMN vRtrMplsTpTunnelID	1.3.6.1.4.1.7483.6.1.2.83.3.1.1.1.5	TmnxTunnelID	not-accessible	The value of vRtrMplsTpTunnelID provides an additional index to distinguish between multiple tunnels to same destination having same characteristics. There could be multiple tunnels for the type 'mplsTpStatic'. In such cases the vRtrMplsTpTunnelID will hold the specific MPLS-TP Static LSP Id.
U32 vRtrMplsTpTunnelIdMax	1.3.6.1.4.1.7483.6.1.2.83.2.1.1.1.5	Unsigned32	read-create	The value of vRtrMplsTpTunnelIdMax specifies the end range of tunnel ids reserved for MPLS-TP LSPs. This variable must be set along with vRtrMplsTpTunnelIdMin to indicate the range of tunnel ids reserved for MPLS-TP LSPs. A value of 0 indicates that tunnel ids are not reserved for MPLS-TP LSPs.
U32 vRtrMplsTpTunnelIdMin	1.3.6.1.4.1.7483.6.1.2.83.2.1.1.1.4	Unsigned32	read-create	The value of vRtrMplsTpTunnelIdMin specifies the start range of tunnel ids reserved for MPLS-TP LSPs. This variable must be set along with vRtrMplsTpTunnelIdMax to indicate the range of tunnel ids reserved for MPLS-TP LSPs. A value of 0 indicates that tunnel ids are not reserved for MPLS-TP LSPs.
U32 vRtrMplsTpTunnelMetric	1.3.6.1.4.1.7483.6.1.2.83.3.1.1.1.8	Unsigned32	read-only	The value of vRtrMplsTpTunnelMetric indicates the metric of the tunnel. This is used in addition to the preference for this tunnel.
IP vRtrMplsTpTunnelNextHopAddress	1.3.6.1.4.1.7483.6.1.2.83.3.1.1.1.7	InetAddress	not-accessible	The value of vRtrMplsTpTunnelNextHopAddress specifies the ip address of the next hop for the MPLS-TP tunnel and it depends on the value of vRtrMplsTpTunnelNextHopAddrType.
IPt vRtrMplsTpTunnelNextHopAddrType	1.3.6.1.4.1.7483.6.1.2.83.3.1.1.1.6	InetAddressType	not-accessible	The value of vRtrMplsTpTunnelNextHopAddrType specifies the address type of vRtrMplsTpTunnelNextHopAddress.
TMN vRtrMplsTpTunnelNodeId	1.3.6.1.4.1.7483.6.1.2.83.3.1.1.1.1	TmnxMplsTpNodeID	not-accessible	vRtrMplsTpTunnelNodeId indicates the destination node id of this tunnel.
U32 vRtrMplsTpTunnelPreference	1.3.6.1.4.1.7483.6.1.2.83.3.1.1.1.3	Unsigned32	not-accessible	The value of vRtrMplsTpTunnelPreference determines the priority of this tunnel versus the other tunnels from different sources. This is an absolute number used internally by the system to specify preferences for the tunnel. The lowest number signifies the most preferred entry in the table.
vRtrMplsTpTunnelTable	1.3.6.1.4.1.7483.6.1.2.83.3.1.1		not-accessible	vRtrMplsTpTunnelTable maintains a list of MPLS-TP tunnels for the specific router instance.
TMN vRtrMplsTpTunnelType	1.3.6.1.4.1.7483.6.1.2.83.3.1.1.1.4	TmnxMplsTpTunnelType	not-accessible	The value of vRtrMplsTpTunnelType indicates the type of this tunnel entity.

RFC description

Manages MPLS Transport Profile components on Nokia SROS carrier-class routers.

Start monitoring Nokia SROS-based router, carrier Ethernet/MPLS-TP transport router (MPLS-TP tunnel/OAM admin status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download TN-MPLS-TP-MIB