All MIBs › TN-IEEE8021-CFM-MIB
Organization: Nokia
Last Updated: 2015-12-18
Category: Ethernet OAM, Nokia Carrier Ethernet
Description: Manages Nokia carrier Ethernet IEEE 802.1ag CFM maintenance domains and MEP configuration.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is TN-IEEE8021-CFM-MIB?
TN-IEEE8021-CFM-MIB is a Nokia (formerly Alcatel-Lucent) enterprise MIB for the 7x50 family of carrier Ethernet routers, extending the IEEE 802.1ag/CFM (Connectivity Fault Management) standard. It exposes configuration and state for Maintenance End Points (MEPs), including their service-distribution-point and virtual-circuit bindings, MAC addresses, and Alarm Indication Signal (AIS) settings. Its primary monitoring value is software/protocol status rather than physical hardware: it lets an operator confirm whether a MEP is generating or receiving AIS alarms, at what interval and priority, and track AIS transmit counts, which directly indicates Ethernet service continuity faults propagating through the network. The MIB explicitly builds on and extends the standard IEEE8021-CFM-MIB, so it depends on that base module's object model for MEP and maintenance-domain semantics. It is deployed on Nokia 7x50 service routers in carrier Ethernet and MPLS/VPLS access networks where CFM is used for service-level fault detection. Engineers can download the TN-IEEE8021-CFM-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in TN-IEEE8021-CFM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Nokia 1830 PSS (Photonic Service Switch) optical transport platform
Monitoring Examples
An administrator would poll tnDot1agCfmMepTable/tnDot1agCfmMepEntry to inspect tnDot1agCfmMepMacAddress and tnDot1agCfmMepSdpId/tnDot1agCfmMepVcId for a given MEP, then check tnDot1agCfmMepEthRxAis to see if the MEP is currently receiving an AIS condition — indicating a fault has been signaled from downstream. tnDot1agCfmMepEthAisTxCount and tnDot1agCfmMepAisInterval let the operator confirm the local MEP is correctly generating AIS at its configured megLevel and priority. A rising tnDot1agCfmMepEthRxAisInterval mismatch against configuration would flag a CFM interoperability issue.
What Can Be Monitored
- MEP AIS receive status
- MEP AIS transmit count
- AIS interval and priority
- MEP MAC address
- SDP/VC binding for a MEP
This MIB depends on
Related MIBs
Imported Objects
From IEEE8021-CFM-MIB
| Dot1agCfmCcmInterval | |
| Dot1agCfmMDLevel | |
| Dot1agCfmMepId | |
| Dot1agCfmMepIdOrZero | |
| Dot1agCfmMpDirection | |
| dot1agCfmMaIndex | OBJECT-TYPE |
| dot1agCfmMaMepListEntry | OBJECT-TYPE |
| dot1agCfmMaNetEntry | OBJECT-TYPE |
| dot1agCfmMdIndex | OBJECT-TYPE |
| dot1agCfmMepEntry | OBJECT-TYPE |
| dot1agCfmMepIdentifier | OBJECT-TYPE |
| dot1agCfmMepTransmitLbmDestMacAddress | OBJECT-TYPE |
| dot1agCfmMepTransmitLtmSeqNumber | OBJECT-TYPE |
From IF-MIB
| InterfaceIndex |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Gauge32 | |
| Integer32 | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| MacAddress | |
| RowStatus | |
| TruthValue |
From TN-SERV-MIB
| SdpId |
From TN-TC-MIB
| TNamedItem | |
| TmnxEnabledDisabled | |
| TmnxServId |
From TROPIC-GLOBAL-REG
| tnSRMIBModules | OBJECT-IDENTITY |
| tnSRNotifyPrefix | OBJECT-IDENTITY |
| tnSRObjs | OBJECT-IDENTITY |
From TROPIC-SYSTEM-MIB
| tnSysSwitchId | OBJECT-TYPE |
How to Use in IPNetwork Monitor
Example using tnDot1agCfmMepEthAisTxCount OID:
Select a Nokia 7x50 series carrier Ethernet/service router (802.1ag CFM MEP/AIS status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type tnDot1agCfmMepEthAisTxCount into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The value of tnDot1agCfmMepEthAisTxCount indicates number of AIS frames transmitted on the MEP. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| tnIEEE8021CfmMIBModule | 1.3.6.1.4.1.7483.5.1.3.52 | This document is the SNMP MIB module to manage and provision dot1ag Connectivity Fault Management module functionality for the Nokia 7x50 products. This includes extensions to the IEEE8021-CFM MIB. Copyright 2008-2012 Nokia. All rights reserved. Reproduction of this document is authorized on the condition that the foregoing copyright notice is included. This SNMP MIB module (Specification) embodies Nokia's proprietary intellectual property. Nokia retains all title and ownership in the Specification, including any revisions. Nokia grants all interested parties a non-exclusive license to use and distribute an unmodified copy of this Specification in connection with management of Nokia products, and without fee, provided this copyright notice and license appear on all copies. This Specification is supplied 'as is', and Nokia makes no warranty, either express or implied, as to the use, operation, condition, or performance of the Specification. | ||
| tnDot1agMIBObjs | 1.3.6.1.4.1.7483.6.1.2.52 | |||
| tnDot1agCfmStack | 1.3.6.1.4.1.7483.6.1.2.52.1 | |||
| tnDot1agCfmStackTable | 1.3.6.1.4.1.7483.6.1.2.52.1.2 | not-accessible | There is one CFM Stack table per bridge. It permits the retrieval of information about the Maintenance Points configured on any given interface. | |
| tnDot1agCfmStackEntry | 1.3.6.1.4.1.7483.6.1.2.52.1.2.1 | not-accessible | The Stack table entry | |
| NUM tnDot1agCfmStackifIndex | 1.3.6.1.4.1.7483.6.1.2.52.1.2.1.1 | InterfaceIndex | not-accessible | This object represents the Bridge Port or aggregated port on which MEPs or MHFs might be configured. Upon a restart of the system, the system SHALL, if necessary, change the value of this variable, and rearrange the dot1agCfmStackTable, so that it indexes the entry in the interface table with the same value of ifAlias that it indexed before the system restart. If no such entry exists, then the system SHALL delete all entries in the dot1agCfmStackTable with the interface index. |
| U32 tnDot1agCfmStackVlanIdOrNone | 1.3.6.1.4.1.7483.6.1.2.52.1.2.1.2 | Unsigned32 | not-accessible | VLAN ID to which the MP is attached, or 0, if none. |
| DOT tnDot1agCfmStackMdLevel | 1.3.6.1.4.1.7483.6.1.2.52.1.2.1.3 | Dot1agCfmMDLevel | not-accessible | MD Level of the Maintenance Point. |
| DOT tnDot1agCfmStackDirection | 1.3.6.1.4.1.7483.6.1.2.52.1.2.1.4 | Dot1agCfmMpDirection | not-accessible | Direction in which the MP faces on the Bridge Port |
| U32 tnDot1agCfmStackMdIndex | 1.3.6.1.4.1.7483.6.1.2.52.1.2.1.5 | Unsigned32 | read-only | The index of the Maintenance Domain in the dot1agCfmMdTable to which the MP is associated, or 0, if none. |
| U32 tnDot1agCfmStackMaIndex | 1.3.6.1.4.1.7483.6.1.2.52.1.2.1.6 | Unsigned32 | read-only | The index of the MA in the dot1agCfmMaNetTable and dot1agCfmMaCompTable to which the MP is associated, or 0, if none. |
| DOT tnDot1agCfmStackMepId | 1.3.6.1.4.1.7483.6.1.2.52.1.2.1.7 | Dot1agCfmMepIdOrZero | read-only | If an MEP is configured, the MEPID, else 0 |
| MAC tnDot1agCfmStackMacAddress | 1.3.6.1.4.1.7483.6.1.2.52.1.2.1.8 | MacAddress | read-only | MAC address of the MP. |
| INT tnDot1agCfmStackMPType | 1.3.6.1.4.1.7483.6.1.2.52.1.2.1.9 | INTEGER | read-only | The value of tnDot1agCfmStackMPType indicates the entity that the MP is configured on: sap(1) MP is configured on a SAP ethTun(2) MP is configured on an ethernet-tunnel |
| tnDot1agCfmGlobalObjs | 1.3.6.1.4.1.7483.6.1.2.52.2 | |||
| tnDot1agCfmMcLagConfigTable | 1.3.6.1.4.1.7483.6.1.2.52.2.1 | not-accessible | A row in the tnDot1agCfmMcLagConfigTable indicates whether a Mc Lag is in Active Standby or not and what the Hold Time will be. | |
| tnDot1agCfmMcLagConfigEntry | 1.3.6.1.4.1.7483.6.1.2.52.2.1.1 | not-accessible | The Cfm entry for MC LAG | |
| T/F tnDot1agCfmMcLagConfigStdbyInactive | 1.3.6.1.4.1.7483.6.1.2.52.2.1.1.1 | TruthValue | read-write | The value of tnDot1agCfmMcLagConfigStdbyInactive specifies whether or not ETH-CFM MEPs configured on Multi-Chassis LAG ports are aware of MC-LAG port active/standby states. When this object is 'true (1)', MEPs configured on a Multi-Chassis LAG port will act as if they are administratively shutdown if running on a standby port, and will only be operational on an active MC-LAG port. When this object is 'false (2)', MEPs configured on a Multi-Chassis LAG port will operate regardless of the MC-LAG port active and standby states. |
| U32 tnDot1agCfmMcLagConfigPropHoldTime | 1.3.6.1.4.1.7483.6.1.2.52.2.1.1.2 | Unsigned32 | read-write | The value of tnDot1agCfmMcLagConfigPropHoldTime specifies the duration, in seconds, of a timer that is activated when an MC-LAG port or protocol changes state. While the timer is active, no fault set or clear is propagated to the MC-LAG SAP's CFM MEP. The outstanding hold time can be monitored by polling the value of sapEthCfmMcLagPropHoldTimeRemain for a particular SAP. When set to the value zero (0), no delay in response to a port or protocol change will be observed. This object is meaningful only when tnDot1agCfmMcLagConfigStdbyInactive is set to the value 'enabled (1)', otherwise an SNMP Set operation will result in an inconsistentValue error and the result of an SNMP Get operation will be undefined. |
| tnDot1agCfmStatisticsGroup | 1.3.6.1.4.1.7483.6.1.2.52.2.3 | |||
| tnDot1agCfmComponentLimitTable | 1.3.6.1.4.1.7483.6.1.2.52.2.3.1 | not-accessible | The tnDot1agCfmComponentLimitTable stores the current resource counts as well as their resource limits for Ethernet Connectivity Fault Management (ETH-CFM) components in the SROS series system. | |
| tnDot1agCfmComponentLimitEntry | 1.3.6.1.4.1.7483.6.1.2.52.2.3.1.1 | not-accessible | The tnDot1agCfmComponentLimitEntry consists of the resource limits for a particular component of ETH-CFM. Rows are managed by the system and can not be created or destroyed using SNMP set requests. | |
| U32 tnDot1agCfmCompMajorIndex | 1.3.6.1.4.1.7483.6.1.2.52.2.3.1.1.1 | Unsigned32 | not-accessible | The value of tnDot1agCfmCompMajorIndex specifies the major identifier of the ETH-CFM component. |
| U32 tnDot1agCfmCompMinorIndex | 1.3.6.1.4.1.7483.6.1.2.52.2.3.1.1.2 | Unsigned32 | not-accessible | The value of tnDot1agCfmCompMinorIndex specifies the minor identifier of the ETH-CFM component. |
| TNA tnDot1agCfmCompName | 1.3.6.1.4.1.7483.6.1.2.52.2.3.1.1.3 | TNamedItem | read-only | The value of tnDot1agCfmCompName indicates the name of the ETH-CFM component. |
| U32 tnDot1agCfmCompResourceUsage | 1.3.6.1.4.1.7483.6.1.2.52.2.3.1.1.4 | Unsigned32 | read-only | The value of tnDot1agCfmCompResourceUsage indicates the current resource usage for the ETH-CFM component. |
| U32 tnDot1agCfmCompResourceLimit | 1.3.6.1.4.1.7483.6.1.2.52.2.3.1.1.5 | Unsigned32 | read-only | The value of tnDot1agCfmCompResourceLimit indicates the maximum resource usage limit for the ETH-CFM component for the SROS series system. |
| U32 tnDot1agCfmGlobalScalar1 | 1.3.6.1.4.1.7483.6.1.2.52.2.101 | Unsigned32 | read-only | A dummy scalar that satisfies a SNMP get request quickly when there is no 11QPE24 card provisioned. Otherwise, it has to traverse the remaining 11QPE24 MIB to get to the next applicable item. |
| U32 tnDot1agCfmGlobalScalar2 | 1.3.6.1.4.1.7483.6.1.2.52.2.102 | Unsigned32 | read-only | |
| tnDot1agCfmMa | 1.3.6.1.4.1.7483.6.1.2.52.6 | |||
| tnDot1agCfmMaNetTable | 1.3.6.1.4.1.7483.6.1.2.52.6.1 | not-accessible | The tnDot1agCfmMaNetTable AUGMENTS the standard MIB table, dot1agCfmMaNetTable. This table is used to enhance Maintenance Association functionality for Ethernet Connectivity Fault Management (ETH-CFM). | |
| tnDot1agCfmMaNetEntry | 1.3.6.1.4.1.7483.6.1.2.52.6.1.1 | not-accessible | The tnDot1agCfmMaNetEntry consists of the configuration objects used to enhance the Maintenance Association functionality. | |
| C32 tnDot1agCfmMaNetTotalMEPCount | 1.3.6.1.4.1.7483.6.1.2.52.6.1.1.1 | Counter32 | read-only | The value of tnDot1agCfmMaNetTotalMEPCount indicates the number of unique MEPs configured (both local and remote) that are associated with this MA. When the number of MEPs exceed the normal MA limits, the MA is considered to be an extended MA and will use a resource from the 'Extended MA' resource entry in tnDot1agCfmComponentLimitTable. |
| tnDot1agCfmMaMepListTable | 1.3.6.1.4.1.7483.6.1.2.52.6.3 | not-accessible | The tnDot1agCfmMaMepListTable extends the functionality of the dot1agCfmMaMepListTable. | |
| tnDot1agCfmMaMepListEntry | 1.3.6.1.4.1.7483.6.1.2.52.6.3.1 | not-accessible | The tnDot1agCfmMaMepListEntry augments the standard MIB entry for the purpose of extending functionality for Dot1ag CFM MEP Lists. Rows are created and destroyed by the system through the row status field in dot1agCfmMaMepListEntry. | |
| MAC tnDot1agCfmMaMepListMacAddress | 1.3.6.1.4.1.7483.6.1.2.52.6.3.1.1 | MacAddress | read-create | The value of tnDot1agCfmMaMepListMacAddress specifies the target unicast MAC address used for transmitting CFM packets to the remote MEPs for the specified MEPID. Setting a unicast MAC address restricts the number of MEPIDs that can be configured for an individual MA to a maximum of one (1). Setting the address back to the default value will remove this restriction and will result in the regular CCM multicast address being used. This value cannot be set to any multicast or broadcast address. |
| tnDot1agCfmMep | 1.3.6.1.4.1.7483.6.1.2.52.7 | |||
| tnDot1agCfmMepTable | 1.3.6.1.4.1.7483.6.1.2.52.7.1 | not-accessible | This table augments the Maintenance Association End Point (MEP) table of the IEEE8021-CFM-MIB. | |
| tnDot1agCfmMepEntry | 1.3.6.1.4.1.7483.6.1.2.52.7.1.1 | not-accessible | A conceptual row in the tnDot1agCfmMepTable. This row exists only if the association dot1agCfmMepEntry is active. | |
| SDP tnDot1agCfmMepSdpId | 1.3.6.1.4.1.7483.6.1.2.52.7.1.1.1 | SdpId | read-create | The value of tnDot1agCfmMepSdpId specifies, along with the tnDot1agCfmMepVcId, the SDP-Binding within a bridge port, to which the MEP is attached. This object is applicable to SDP-Bindings only, and MUST be set to the null ID (0) when dot1agCfmMepIfIndex or dot1agCfmMepPrimaryVid, is non-zero. When this object is applicable (non-zero), the dot1agCfmMepIfIndex and dot1agCfmMepPrimaryVid MUST be set to zero (0). |
| U32 tnDot1agCfmMepVcId | 1.3.6.1.4.1.7483.6.1.2.52.7.1.1.2 | Unsigned32 | read-create | The value of tnDot1agCfmMepVcId specifies, along with tnDot1agCfmMepSdpId, the SDP Binding for the bridge. tnDot1agCfmMepVcId is applicable to SDP-Bindings only, and MUST be set to zero (0) when dot1agCfmMepIfIndex or dot1agCfmMepPrimaryVid is non-zero. When this object is applicable (non-zero), the dot1agCfmMepIfIndex and dot1agCfmMepPrimaryVid MUST be set to zero (0). |
| MAC tnDot1agCfmMepMacAddress | 1.3.6.1.4.1.7483.6.1.2.52.7.1.1.3 | MacAddress | read-create | The value of tnDot1agCfmMepMacAddress specifies the mac-address that is assigned to dot1agCfmMepMacAddress. |
| T/F tnDot1agCfmMepAisEnable | 1.3.6.1.4.1.7483.6.1.2.52.7.1.1.4 | TruthValue | read-create | The value of tnDot1agCfmMepAisEnable specifies whether AIS frames are generated from the Maintenance Entity Group (MEG). |
| BIT tnDot1agCfmMepAisMegLevel | 1.3.6.1.4.1.7483.6.1.2.52.7.1.1.5 | Bits | read-create | The value of tnDot1agCfmMepAisMegLevel specifies the levels that should be notified to suppress alarms resulting from defect conditions detected by the MEP. |
| U32 tnDot1agCfmMepAisPriority | 1.3.6.1.4.1.7483.6.1.2.52.7.1.1.6 | Unsigned32 | read-create | The value of tnDot1agCfmMepAisPriority specifies at what priority the AIS frames should be transmitted. |
| U32 tnDot1agCfmMepAisInterval | 1.3.6.1.4.1.7483.6.1.2.52.7.1.1.7 | Unsigned32 | read-create | The value of tnDot1agCfmMepAisInterval specifies at what intervals to transmit AIS frames. |
| U32 tnDot1agCfmMepEthRxAisInterval | 1.3.6.1.4.1.7483.6.1.2.52.7.1.1.8 | Unsigned32 | read-only | The value of tnDot1agCfmMepEthRxAisInterval indicates the AIS Interval received in the last AIS Frame. |
| T/F tnDot1agCfmMepEthRxAis | 1.3.6.1.4.1.7483.6.1.2.52.7.1.1.9 | TruthValue | read-only | The value of tnDot1agCfmMepEthRxAis indicates the MEP is receiving AIS test frames from one or more of its sub-layer MEPs. |
| C32 tnDot1agCfmMepEthAisTxCountEx | 1.3.6.1.4.1.7483.6.1.2.52.7.1.1.10 | Counter32 | read-only | The value of tnDot1agCfmMepEthAisTxCount indicates number of AIS frames transmitted on the MEP. |
| T/F tnDot1agCfmMepEthTestEnable | 1.3.6.1.4.1.7483.6.1.2.52.7.1.1.11 | TruthValue | read-create | The value of tnDot1agCfmMepEthTestEnable specifies whether ethernet test frames are to be generated on transmission or processed on reception. If this object is set to 'false', then tnDot1agCfmMepEthTestPattern is undefined. When this object is set to 'true', tnDot1agCfmMepEthTestPattern is reset to its default value, unless tnDot1agCfmMepEthTestPattern is set to a specific value in the same SNMP PDU. |
| INT tnDot1agCfmMepEthTestPattern | 1.3.6.1.4.1.7483.6.1.2.52.7.1.1.12 | INTEGER | read-create | The value of tnDot1agCfmMepEthTestPattern specifies the data-content of the AIS test frames. 'allZerosNoCrc (0)' and 'allZerosCrc (1)' specifies the data content as all zero values (without and with CRC calculations respectively). 'prbsNoCrc (3) and 'prbsCrc (4) specifies the data content as pseudo random bit sequence (without and with CRC calculations respectively). 'allOnesNoCrc (4)' and 'allOnesCrc (5)', specifies the data content as all ones (without and with CRC calculations respectively). This object is only applicable if tnDot1agCfmMepEthTestEnable is set to 'true'. |
| MAC tnDot1agCfmMepEthTestMacAddr | 1.3.6.1.4.1.7483.6.1.2.52.7.1.1.13 | MacAddress | read-create | The value of tnDot1agCfmMepEthTestMacAddr specifies the MAC address of the target to whom the Eth-test frames are sent. Setting this object will trigger the test frame to be sent. Once the test is complete, the object will revert to the default value, indicating that another test is possible. |
| U32 tnDot1agCfmMepEthTestDataLen | 1.3.6.1.4.1.7483.6.1.2.52.7.1.1.14 | Unsigned32 | read-create | The value of tnDot1agCfmMepEthTestDataLen specifies the length of the data sent in an Eth-test frame. The contents of the data is specified by the tnDot1agCfmMepEthTestPattern object. |
| U32 tnDot1agCfmMepEthTestPriority | 1.3.6.1.4.1.7483.6.1.2.52.7.1.1.15 | Unsigned32 | read-create | The value of tnDot1agCfmMepEthTestPriority specifies the priority used in generating Eth-Test frames. |
| MAC tnDot1agCfmMepOWDTMacAddress | 1.3.6.1.4.1.7483.6.1.2.52.7.1.1.16 | MacAddress | read-create | The value of tnDot1agCfmMepOWDTMacAddress specifies the MAC address used as a target for the One-Way-Delay Test (OWDT). Setting this object will trigger a One-Way-Delay test to the specified MAC address. Upon completion of the test, the MacAddress will revert to it's default value, indicating that another test is possible. |
| U32 tnDot1agCfmMepOWDTPriority | 1.3.6.1.4.1.7483.6.1.2.52.7.1.1.17 | Unsigned32 | read-create | The value of tnDot1agCfmMepOWDTPriority specifies the priority used in the generated test frame for the One-Way-Delay test. |
| MAC tnDot1agCfmMepTWDTMacAddress | 1.3.6.1.4.1.7483.6.1.2.52.7.1.1.18 | MacAddress | read-create | The value of tnDot1agCfmMepTWDTMacAddress specifies the MAC address used as a target for the Two-Way-Delay Test (TWDT). Setting this object will trigger a Two-Way-Delay test to the specified MAC address. Upon completion of the test, the MacAddress will revert to it's default value, indicating that another test is possible. |
| U32 tnDot1agCfmMepTWDTPriority | 1.3.6.1.4.1.7483.6.1.2.52.7.1.1.19 | Unsigned32 | read-create | The value of tnDot1agCfmMepTWDTPriority specifies the priority used in the generated test frame for the Two-Way-Delay test. |
| TMN tnDot1agCfmMepSvcId | 1.3.6.1.4.1.7483.6.1.2.52.7.1.1.20 | TmnxServId | read-create | The value of tnDot1agCfmMepSvcId specifies the service that the virtual MEP is being created in. tnDot1agCfmMepSvcId is applicable to virtual MEPs only, and MUST be set to zero (0) when dot1agCfmMepIfIndex, dot1agCfmMepPrimaryVid, tnDot1agCfmMepSdpId, or tnDot1agCfmMepVcId is non-zero. When this object is applicable (non-zero), the above objects MUST be set to zero (0). |
| T/F tnDot1agCfmMepControlMep | 1.3.6.1.4.1.7483.6.1.2.52.7.1.1.21 | TruthValue | read-create | The value of tnDot1agCfmMepControlMep specifies whether or not the operational state of the MEP is used by the management entity over which this MEP is configured. |
| U32 tnDot1agCfmMepEthTestThreshold | 1.3.6.1.4.1.7483.6.1.2.52.7.1.1.22 | Unsigned32 | read-create | The value of tnDot1agCfmMepEthTestThreshold specifies when a tnDot1agCfmMepEthTestComplete notification is sent. If tnDot1agCfmMepEthTestThreshold is set to zero (0), a notification is sent on the completion of any test for this MEP. Otherwise the threshold must be exceeded and/or CRC failures must be detected to send the notification. |
| U32 tnDot1agCfmMepOWDTThreshold | 1.3.6.1.4.1.7483.6.1.2.52.7.1.1.23 | Unsigned32 | read-create | The value of tnDot1agCfmMepOWDTThreshold specifies when a tnDot1agCfmMepDMTestComplete notification is sent for a one-way-delay test. If tnDot1agCfmMepOWDTThreshold is set to zero (0), a notification is sent on the completion of any one-way-delay-test for this MEP. Otherwise the threshold must be exceeded to send the notification. |
| INT tnDot1agCfmMepMcLagInactive | 1.3.6.1.4.1.7483.6.1.2.52.7.1.1.24 | INTEGER | read-only | The value of tmnxDot1agCfmMepMcLagInactive indicates whether or not the MEP is inactive, 'standby (2)', due to the MC-LAG standby state. The value of tmnxDot1agCfmMcLagStdbyInactive must be set to 'true (1)' for this object to have meaning and return anything other than 'notApplicable (0)'. |
| U32 tnDot1agCfmMepTWDTDataSize | 1.3.6.1.4.1.7483.6.1.2.52.7.1.1.25 | Unsigned32 | read-create | The value of tnDot1agCfmMepTWDTDataSize specifies the data size, in bytes, contained in the padding TLV for the Two-Way delay test. A value of zero (0) specifies that no padding TLV is inserted in the packet. Any non-zero value will increase the packet size by the specified data size plus 3 bytes for the TLV header. |
| U32 tnDot1agCfmMepTransmitLbmDataTlvSize | 1.3.6.1.4.1.7483.6.1.2.52.7.1.1.26 | Unsigned32 | read-create | The value of tnDot1agCfmMepTransmitLbmDataTlvSize specifies the data size, in bytes, contained in the padding TLV for the LBM test. A value of zero (0) specifies that no padding TLV is inserted in the packet. Any non-zero value will increase the packet size by the specified data size. |
| INT tnDot1agCfmMepType | 1.3.6.1.4.1.7483.6.1.2.52.7.1.1.27 | INTEGER | read-create | The value of tmnxDot1agCfmMepType specifies the endpoint type that this MEP facilitates. default (0) -- implements a traditional MEP. facilityPort (1) -- implements a facility port/LAG level MEP. facilityInterface (2) -- implements a router interface level MEP. sapPrimaryVlan (3) -- implements a SAP MEP using primary VLAN-ID from the MA Comp Table. This is only applicable if the MA primary VLAN ID is set to a value other than zero (0). This object must be specified during row creation. |
| INT tnDot1agCfmMepFaultPropagation | 1.3.6.1.4.1.7483.6.1.2.52.7.1.1.28 | INTEGER | read-create | The value of tnDot1agCfmMepFaultPropagation specifies what action should be taken by the MEP if a fault is detected in the service containing the MEP. It also specifies if the MEP should propagate a fault that it has detected into the service. When this object is set to 'disabled (0)', no additional fault propagation will occur. When this object is set to 'useIfStatusTLV (1)', the MEP will send an interface status TLV in the next CCM indicating fault when fault is detected, even if the MEP itself has not detected a fault. When this object is set to 'suspendCCM (2)', faults will be propagated by stopping the regular CCM transmissions entirely. Once the fault is cleared, the regular CCM transmissions will resume. Additionally, when the value of tnDot1agCfmMepFaultPropagation is different than 'disabled (0)', a defect detected by the MEP will be propagated into the service. |
| tnDot1agCfmMepDelayRsltTable | 1.3.6.1.4.1.7483.6.1.2.52.7.3 | not-accessible | The tnDot1agCfmMepDelayRsltTable indicates the results of all the One-Way/Two-Way Delay Tests from the originating MAC addresses. This table is not persistent over reboots of the chassis. | |
| tnDot1agCfmMepDelayRsltEntry | 1.3.6.1.4.1.7483.6.1.2.52.7.3.1 | not-accessible | The MEG result table. | |
| MAC tnDot1agCfmMepDelaySrcMacAddr | 1.3.6.1.4.1.7483.6.1.2.52.7.3.1.1 | MacAddress | not-accessible | The value of tnDot1agCfmMepDelaySrcMacAddr indicates the source MAC address of the issuer of the test. |
| INT tnDot1agCfmMepDelayTestType | 1.3.6.1.4.1.7483.6.1.2.52.7.3.1.2 | INTEGER | not-accessible | The value of tnDot1agCfmMepDelayTestType indicates the type of test this row details. |
| I32 tnDot1agCfmMepDelayTestDelay | 1.3.6.1.4.1.7483.6.1.2.52.7.3.1.3 | Integer32 | read-only | The value of tnDot1agCfmMepDelayTestDelay indicates the amount of time, measured in microseconds, from when the test-frame was transmitted to the time it was received minus the local processing time taken by the remote system. |
| U32 tnDot1agCfmMepDelayVariation | 1.3.6.1.4.1.7483.6.1.2.52.7.3.1.4 | Unsigned32 | read-only | The value of tnDot1agCfmMepDelayVariation indicates the amount of time delay variation, measured in microseconds, from the two most recent time delay measurements |
| tnDot1agCfmMepCsfTable | 1.3.6.1.4.1.7483.6.1.2.52.7.4 | not-accessible | This table augments the Maintenance Association End Point (MEP) table of the IEEE8021-CFM-MIB. | |
| tnDot1agCfmMepCsfEntry | 1.3.6.1.4.1.7483.6.1.2.52.7.4.1 | not-accessible | A conceptual row in the tnDot1agCfmMepCsfTable. This row exists only if the association dot1agCfmMepEntry is active. | |
| NUM tnDot1agCfmMepCsfInterval | 1.3.6.1.4.1.7483.6.1.2.52.7.4.1.1 | Dot1agCfmCcmInterval | read-create | Interval between CSF transmissions to be used in the MEP. |
| INT tnDot1agCfmMepCsfDirection | 1.3.6.1.4.1.7483.6.1.2.52.7.4.1.2 | INTEGER | read-write | CSF transmissions direction in the MEP |
| I32 tnDot1agCfmMepCsfPriority | 1.3.6.1.4.1.7483.6.1.2.52.7.4.1.3 | Integer32 | read-create | The priority value for CSFs transmitted by the MEP. Default Value is the highest priority value allowed to pass through the bridge port for any of this MEPs VIDs. The management entity can obtain the default value for this variable from the priority regeneration table by extracting the highest priority value in this table on this MEPs bridge port. |
| tnDot1agCfmMepSlmTWTestTable | 1.3.6.1.4.1.7483.6.1.2.52.7.5 | not-accessible | tnDot1agCfmMepSlmTWTestTable consists of the MEP configuration for issuing individual Synthetic Loss Measurement tests. | |
| tnDot1agCfmMepSlmTWTestEntry | 1.3.6.1.4.1.7483.6.1.2.52.7.5.1 | not-accessible | tnDot1agCfmMepSlmTWTestEntry contains the configuration for generating Synthetic Loss Measurement (SLM) Tests for a particular MEP. A row exists for each row in the dot1agCfmMepTable, and is destroyed automatically with the removal of a row in the dot1agCfmMepTable. Results from a two-way SLM test are reported in tnDot1agCfmMepSlmTestRsltTable with the tnDot1agCfmMepSlmTestType set to 'twoWayTest (2)'. | |
| TMN tnDot1agCfmMepSlmTWTestStatus | 1.3.6.1.4.1.7483.6.1.2.52.7.5.1.1 | TmnxEnabledDisabled | read-create | The value of tnDot1agCfmMepSlmTWTestStatus specifies the operational state of the two-way Synthetic Loss Measurement (SLM) test. To issue a two-way SLM test the user must issue an SNMP SET on this object with a value 'enabled (1)'. To abort the two-way SLM test issue an SNMP SET on this object with the value 'disabled (2)'. A read on this object represents the current state of the two-way SLM test: enabled (1) - The test is actively running, and attempts at modifying any two-way SLM object will be rejected disabled (2) - The test is not running. Once the test is complete this object will revert to the default value 'disabled (2)'. |
| U32 tnDot1agCfmMepSlmTWTestId | 1.3.6.1.4.1.7483.6.1.2.52.7.5.1.2 | Unsigned32 | read-only | The value of tnDot1agCfmMepSlmTWTestId indicates the test identifier used to initiate the two-way Synthetic Loss Measurement (SLM) test. |
| MAC tnDot1agCfmMepSlmTWMacAddress | 1.3.6.1.4.1.7483.6.1.2.52.7.5.1.3 | MacAddress | read-create | The value of tnDot1agCfmMepSlmTWMacAddress specifies the MAC address used as a target for the two-way Synthetic Loss Measurement (SLM) test. This object MUST be set to a valid MAC Address for proper execution of the two-way SLM test. |
| U32 tnDot1agCfmMepSlmTWPriority | 1.3.6.1.4.1.7483.6.1.2.52.7.5.1.4 | Unsigned32 | read-create | The value of tnDot1agCfmMepSlmTWPriority specifies the priority used in the generated test frame for the two-way Synthetic Loss Measurement (SLM) test. |
| U32 tnDot1agCfmMepSlmTWInterval | 1.3.6.1.4.1.7483.6.1.2.52.7.5.1.5 | Unsigned32 | read-create | The value of tnDot1agCfmMepSlmTWInterval specifies the delay, in seconds, between Synthetic Loss Measurement (SLM) messages for the two-way SLM test. |
| U32 tnDot1agCfmMepSlmTWTimeout | 1.3.6.1.4.1.7483.6.1.2.52.7.5.1.6 | Unsigned32 | read-create | The value of tnDot1agCfmMepSlmTWTimeout specifies the time-out value, in seconds, to wait for a Synthetic Loss Measurement (SLM) message to reply for the two-way SLM test. Upon expiration of the timeout period, the agent assumes that the message response will not be received. Any response received after the timeout period has expired is silently discarded. |
| U32 tnDot1agCfmMepSlmTWDataSize | 1.3.6.1.4.1.7483.6.1.2.52.7.5.1.7 | Unsigned32 | read-create | The value of tnDot1agCfmMepSlmTWDataSize specifies the data size, in bytes, contained in the padding TLV for the two-way Synthetic Loss Measurement (SLM) test. A value of zero (0) specifies that no padding TLV is inserted in the SLM packet. Any non-zero value will increase the packet size by the specified data size plus 3 bytes for the TLV header. |
| U32 tnDot1agCfmMepSlmTWSendCount | 1.3.6.1.4.1.7483.6.1.2.52.7.5.1.8 | Unsigned32 | read-create | The value of tnDot1agCfmMepSlmTWSendCount specifies the number of Synthetic Loss Measurement (SLM) packets to send during the two-way SLM test. |
| U32 tnDot1agCfmMepSlmTWIntervalRedef | 1.3.6.1.4.1.7483.6.1.2.52.7.5.1.9 | Unsigned32 | read-create | The value of tnDot1agCfmMepSlmTWIntervalRedef specifies the interval of SLM frames transmitted. The permitted values are 100ms(0),1s (1),10s(2),1m(3),10(4). |
| INT tnDot1agCfmMepSlmTWIntrvlUnits | 1.3.6.1.4.1.7483.6.1.2.52.7.5.1.10 | INTEGER | read-create | The value of tnDot1agCfmMepSlmTWIntrvlUnits, in conjuction with tnDot1agCfmMepSlmTWInterval, specifies the interval between Synthetic Loss Measurement (SLM) messages sent by the two-way SLM test. For example, if tnDot1agCfmMepSlmTWInterval has the value 90, and tnDot1agCfmMepSlmTWIntrvlUnits has the value 'centiseconds(2)', the interval between SLM messages is 0.9 seconds. The intervals supported are shown in the tnDot1agCfmMepSlmTWInterval DESCRIPTION clause. |
| tnDot1agCfmMepSlmOWTestTable | 1.3.6.1.4.1.7483.6.1.2.52.7.6 | not-accessible | tnDot1agCfmMepSlmOWTestTable consists of the MEP configuration for issuing individual Synthetic Loss Measurement one-way tests. | |
| tnDot1agCfmMepSlmOWTestEntry | 1.3.6.1.4.1.7483.6.1.2.52.7.6.1 | not-accessible | tnDot1agCfmMepSlmOWTestEntry contains the configuration for generating Synthetic Loss Measurement (SLM) Tests for a particular MEP. A row exists for each row in the dot1agCfmMepTable, and is destroyed automatically with the removal of a row in the dot1agCfmMepTable. Results from a one-way SLM test are reported in tnDot1agCfmMepSlmTestRsltTable with tnDot1agCfmMepSlmTestType set to 'oneWayTest (1)'. | |
| TMN tnDot1agCfmMepSlmOWTestStatus | 1.3.6.1.4.1.7483.6.1.2.52.7.6.1.1 | TmnxEnabledDisabled | read-create | The value of tnDot1agCfmMepSlmOWTestStatus specifies the operational state of the one-way Synthetic Loss Measurement (SLM) test. To issue a one-way SLM test the user must issue an SNMP SET on this object with a value 'enabled (1)'. To abort the one-way SLM test issue an SNMP SET on this object with the value 'disabled (2)'. A read on this object represents the current state of the one-way SLM test: enabled (1) - The test is actively running, and attempts at modifying any one-way SLM object will be rejected disabled (2) - The test is not running. Once the test is complete this object will revert to the default value 'disabled (2)'. |
| U32 tnDot1agCfmMepSlmOWTestId | 1.3.6.1.4.1.7483.6.1.2.52.7.6.1.2 | Unsigned32 | read-only | The value of tnDot1agCfmMepSlmOWTestId indicates the test identifier used to initiate the one-way Synthetic Loss Measurement (SLM) test. |
| MAC tnDot1agCfmMepSlmOWMacAddress | 1.3.6.1.4.1.7483.6.1.2.52.7.6.1.3 | MacAddress | read-create | The value of tnDot1agCfmMepSlmOWMacAddress specifies the MAC address used as a target for the one-way Synthetic Loss Measurement (SLM) Test. This object MUST be set to a valid MAC Address for proper execution of the one-way SLM test. |
| U32 tnDot1agCfmMepSlmOWPriority | 1.3.6.1.4.1.7483.6.1.2.52.7.6.1.4 | Unsigned32 | read-create | The value of tnDot1agCfmMepSlmOWPriority specifies the priority used in the generated test frame for the one-way Synthetic Loss Measurement (SLM) test. |
| U32 tnDot1agCfmMepSlmOWInterval | 1.3.6.1.4.1.7483.6.1.2.52.7.6.1.5 | Unsigned32 | read-create | The value of tnDot1agCfmMepSlmOWInterval specifies the delay, in seconds, between Synthetic Loss Measurement (SLM) messages for the one-way SLM test. |
| U32 tnDot1agCfmMepSlmOWDataSize | 1.3.6.1.4.1.7483.6.1.2.52.7.6.1.6 | Unsigned32 | read-create | The value of tnDot1agCfmMepSlmOWDataSize specifies the data size, in bytes, contained in the padding TLV for the one-way Synthetic Loss Measurement (SLM) test. A value of zero (0) specifies that no padding TLV is inserted in the SLM packet. Any non-zero value will increase the packet size by the specified data size plus 3 bytes for the TLV header. |
| U32 tnDot1agCfmMepSlmOWSendCount | 1.3.6.1.4.1.7483.6.1.2.52.7.6.1.7 | Unsigned32 | read-create | The value of tnDot1agCfmMepSlmOWSendCount specifies the number of Synthetic Loss Measurement (SLM) packets to send consecutively during the one-way SLM test. |
| tnDot1agCfmMepSlmTestRsltTable | 1.3.6.1.4.1.7483.6.1.2.52.7.7 | not-accessible | tnDot1agCfmMepSlmTestRsltTable consists of the results of manually triggered Synthetic Loss Measurement tests. | |
| tnDot1agCfmMepSlmTestRsltEntry | 1.3.6.1.4.1.7483.6.1.2.52.7.7.1 | not-accessible | tnDot1agCfmMepSlmTestRsltEntry contains the results of a manually triggered Synthetic Loss Measurement (SLM) test for a particular MEP. Rows are auto-generated by the system based on the issuing of a SLM test. | |
| INT tnDot1agCfmMepSlmTestType | 1.3.6.1.4.1.7483.6.1.2.52.7.7.1.1 | INTEGER | not-accessible | The value of tnDot1agCfmMepSlmTestType specifies whether the row for this Synthetic Loss Measurement (SLM) test refers to a two-way SLM test. |
| MAC tnDot1agCfmMepSlmRemoteMacAddr | 1.3.6.1.4.1.7483.6.1.2.52.7.7.1.2 | MacAddress | not-accessible | The value of tnDot1agCfmMepSlmRemoteMacAddr specifies the source MAC address of the remote node involved in the test. |
| U32 tnDot1agCfmMepSlmTestId | 1.3.6.1.4.1.7483.6.1.2.52.7.7.1.3 | Unsigned32 | read-only | The value of tnDot1agCfmMepSlmTestId indicates the test identifier that was used to initiate the Synthetic Loss Measurement (SLM) test. |
| DOT tnDot1agCfmMepSlmRemoteMepId | 1.3.6.1.4.1.7483.6.1.2.52.7.7.1.4 | Dot1agCfmMepId | read-only | The value of tnDot1agCfmMepSlmRemoteMepId indicates the MEP Identifier of the remote node involved in the test. |
| U32 tnDot1agCfmMepSlmLastTxSeqF | 1.3.6.1.4.1.7483.6.1.2.52.7.7.1.5 | Unsigned32 | read-only | The value of tnDot1agCfmMepSlmLastTxSeqF indicates the last received sequence number on the local node, transmitted by the remote node. |
| C32 tnDot1agCfmMepSlmPacketIn | 1.3.6.1.4.1.7483.6.1.2.52.7.7.1.6 | Counter32 | read-only | The value of tnDot1agCfmMepSlmPacketIn indicates the number of packets received during the execution of the test. |
| I32 tnDot1agCfmMepSlmPacketLossIn | 1.3.6.1.4.1.7483.6.1.2.52.7.7.1.7 | Integer32 | read-only | The value of tnDot1agCfmMepSlmPacketLossIn indicates the number of packets transmitted from the remote node but not received on the local node during the execution of the test. |
| I32 tnDot1agCfmMepSlmPacketLossOut | 1.3.6.1.4.1.7483.6.1.2.52.7.7.1.8 | Integer32 | read-only | The value of tnDot1agCfmMepSlmPacketLossOut indicates the number of packets transmitted from the local node but not received on the remote node during the execution of the test. |
| G32 tnDot1agCfmMepSlmPacketUnack | 1.3.6.1.4.1.7483.6.1.2.52.7.7.1.9 | Gauge32 | read-only | The value of tnDot1agCfmMepSlmPacketUnack indicates the number of unacknowledged lost packets during the execution of the test. |
| tnDot1agCfmMepOndemandLmTestTable | 1.3.6.1.4.1.7483.6.1.2.52.7.8 | not-accessible | tnDot1agCfmMepOndemandLmTestTable consists of the MEP configuration for issuing individual on-demand Regular Loss Measurement tests. | |
| tnDot1agCfmMepOndemandLmTestEntry | 1.3.6.1.4.1.7483.6.1.2.52.7.8.1 | not-accessible | tnDot1agCfmMepOndemandLmTestEntry contains the configuration for generating regular Loss Measurement (LM) Tests for a particular MEP. A row exists for each row in the dot1agCfmMepTable, and is destroyed automatically with the removal of a row in the dot1agCfmMepTable. Results from a on-demand regualar LM test are reported in tnDot1agCfmMepOndemandLmTestRsltTable. | |
| TMN tnDot1agCfmMepOndemandLmTestStatus | 1.3.6.1.4.1.7483.6.1.2.52.7.8.1.1 | TmnxEnabledDisabled | read-create | The value of tnDot1agCfmMepOndemandLmTestStatus specifies the operational state of the on-demand regular Loss Measurement (LM) test. To issue a on-demand regular LM test the user must issue an SNMP SET on this object with a value 'enabled (1)'. To abort the on-demand regular LM test issue an SNMP SET on this object with the value 'disabled (2)'. A read on this object represents the current state of the two-way SLM test: enabled (1) - The test is actively running, and attempts at modifying any on-demand regular LM object will be rejected disabled (2) - The test is not running. Once the test is complete this object will revert to the default value 'disabled (2)'. |
| MAC tnDot1agCfmMepOndemandLmDestMacAddress | 1.3.6.1.4.1.7483.6.1.2.52.7.8.1.2 | MacAddress | read-create | The value of tnDot1agCfmMepOndemandLmMacAddress specifies the MAC address used as a target for the on-demand regular Loss Measurement (LM) test. This object MUST be set to a valid MAC Address for proper execution of the on-demand regular LM test. |
| U32 tnDot1agCfmMepOndemandLmPriority | 1.3.6.1.4.1.7483.6.1.2.52.7.8.1.3 | Unsigned32 | read-create | The value of tnDot1agCfmMepOndemandLmPriority specifies the priority used in the generated test frame for the on-demand regular Loss Measurement (LM) test. |
| NUM tnDot1agCfmMepOndemandLmInterval | 1.3.6.1.4.1.7483.6.1.2.52.7.8.1.4 | Dot1agCfmCcmInterval | read-create | The value of tnDot1agCfmMepOndemandLmInterval specifies the delay, in seconds, between on-demand regular Loss Measurement (LM) messages for the on-demand regular LM test. allowed values: 100ms, 1s(default), 10s, 1m, 10m. |
| U32 tnDot1agCfmMepOndemandLmSendCount | 1.3.6.1.4.1.7483.6.1.2.52.7.8.1.5 | Unsigned32 | read-create | The value of tnDot1agCfmMepOndemandLmSendCount specifies the number of LMM packets to send during the on-demand regular LM test. |
| tnDot1agCfmMepOndemandLmTestRsltTable | 1.3.6.1.4.1.7483.6.1.2.52.7.9 | not-accessible | tnDot1agCfmMepOndemandLmTestRsltTable consists of the results of manually triggered on-demand regular Loss Measurement tests. | |
| tnDot1agCfmMepOndemandLmTestRsltEntry | 1.3.6.1.4.1.7483.6.1.2.52.7.9.1 | not-accessible | tnDot1agCfmMepOndemandLmTestRsltEntry contains the results of a manually triggered on-demand regular Loss Measurement (LM) test. Rows are auto-generated by the system based on the issuing of a on-demand regular LM test. | |
| C32 tnDot1agCfmMepOndemandLmTnTF | 1.3.6.1.4.1.7483.6.1.2.52.7.9.1.1 | Counter32 | read-only | The value of tnDot1agCfmMepOndemandLmTnTF indicates the total number of near-end transmitted service frames from the remote node during the execution of the test. |
| C32 tnDot1agCfmMepOndemandLmTnLF | 1.3.6.1.4.1.7483.6.1.2.52.7.9.1.2 | Counter32 | read-only | The value of tnDot1agCfmMepOndemandLmTnLF indicates the total number of near-end lost service frames on the local node during the execution of the test. |
| C32 tnDot1agCfmMepOndemandLmTfTF | 1.3.6.1.4.1.7483.6.1.2.52.7.9.1.3 | Counter32 | read-only | The value of tnDot1agCfmMepOndemandLmTfTF indicates the total number of far-end transmitted service frames from the local node during the execution of the test. |
| C32 tnDot1agCfmMepOndemandLmTfLF | 1.3.6.1.4.1.7483.6.1.2.52.7.9.1.4 | Counter32 | read-only | The value of tnDot1agCfmMepOndemandLmTfLF indicates the total number of far-end lost service frames on the remote node during the execution of the test. |
| G32 tnDot1agCfmMepOndemandLmUnack | 1.3.6.1.4.1.7483.6.1.2.52.7.9.1.5 | Gauge32 | read-only | The value of tnDot1agCfmMepOndemandLmUnack indicates the number of unacknowledged lost LM packets during the execution of the test. |
| tnDot1agCfmMepOWDelayRsltExtTable | 1.3.6.1.4.1.7483.6.1.2.52.7.10 | not-accessible | The tnDot1agCfmMepOWDelayRsltExtTable indicates the near-end One-way Delay result. This table is not persistent over reboots of the chassis. | |
| tnDot1agCfmMepOWDelayRsltExtEntry | 1.3.6.1.4.1.7483.6.1.2.52.7.10.1 | not-accessible | The near-end one-way delay test result table. | |
| I32 tnDot1agCfmMepOWDelayRsltExtTnFD | 1.3.6.1.4.1.7483.6.1.2.52.7.10.1.1 | Integer32 | read-only | The value of tnDot1agCfmMepOWDelayRsltExtTnFD indicates one-way near-end frame delay from remote MEP to local MEP. It is the amount of time, measured in microseconds, from when the test-frame was transmitted by the remote MEP to the time it was received local MEP. |
| I32 tnDot1agCfmMepOWDelayRsltExtTnFDV | 1.3.6.1.4.1.7483.6.1.2.52.7.10.1.2 | Integer32 | read-only | The value of tnDot1agCfmMepDelayVariation indicates the amount of near-end one-way time delay variation, measured in microseconds, from the two most recent near-end one-way time delay measurements |
| U32 tnDot1agCfmMepScalar1 | 1.3.6.1.4.1.7483.6.1.2.52.7.101 | Unsigned32 | read-only | A dummy scalar that satisfies a SNMP get request quickly when there is no 11QPE24 card provisioned. Otherwise, it has to traverse the remaining 11QPE24 MIB to get to the next applicable item. |
| U32 tnDot1agCfmMepScalar2 | 1.3.6.1.4.1.7483.6.1.2.52.7.102 | Unsigned32 | read-only | |
| tnDot1agNotificationsPrefix | 1.3.6.1.4.1.7483.6.1.3.52 | |||
| tnDot1agNotifications | 1.3.6.1.4.1.7483.6.1.3.52.0 | |||
| NTF tnDot1agCfmMepLbmTestComplete | 1.3.6.1.4.1.7483.6.1.3.52.0.1 | The tnDot1agCfmMepLbmTestComplete notification indicates that a loopback test has been issued and results are ready. | ||
| NTF tnDot1agCfmMepLtmTestComplete | 1.3.6.1.4.1.7483.6.1.3.52.0.2 | The tnDot1agCfmMepLtmTestComplete notification indicates that a linktrace test has been issued and results are ready. The dot1agCfmMepTransmitLtmSeqNumber indicates the Transaction Identifier to use to retrieve the Link-trace results. | ||
| NTF tnDot1agCfmMepDMTestComplete | 1.3.6.1.4.1.7483.6.1.3.52.0.4 | The tnDot1agCfmMepDMTestComplete notification indicates that a One-Way-Delay-Test (OWDT) frame, or a Two-Way-Delay-Test (TWDT) response was received. For an OWDT frame, traps are raised only when a delay threshold of three (3) seconds is exceeded. | ||
| NTF tnDot1agCfmMepAisStateChanged | 1.3.6.1.4.1.7483.6.1.3.52.0.5 | The tnDot1agCfmMepAisStateChanged notification is generated when a MEP enters or exits an AIS state. | ||
| NTF tnDot1agCfmMepSLMTestComplete | 1.3.6.1.4.1.7483.6.1.3.52.0.7 | The tnDot1agCfmMepSLMTestComplete notification is generated when a two-way Synthetic Loss Measurement (SLM) test is completed. | ||
| NTF tnDot1agCfmMepOndemandLmTestComplete | 1.3.6.1.4.1.7483.6.1.3.52.0.8 | The tnDot1agCfmMepOndemandLmTestComplete notification is generated when a on-demand regular Loss Measurement (LM) test is completed. |
RFC description
Nokia 7x50 extensions to IEEE 802.1ag Connectivity Fault Management for Ethernet OAM.
Start monitoring Nokia 7x50 series carrier Ethernet/service router (802.1ag CFM MEP/AIS status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.