PEA-VDSL-IPDSLAM

All MIBs › PEA-VDSL-IPDSLAM

Organization: Ericsson Diax A/S - Denmark

Last Updated: 2004-05-03

Category: DSL and Broadband

Description: Manages VDSL line provisioning, attainable rates, band plan, and performance monitoring on the Ericsson Diax IP DSLAM.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is PEA-VDSL-IPDSLAM?

PEA-VDSL-IPDSLAM is an Ericsson Diax IP DSLAM proprietary MIB for managing VDSL/VDSL2 line pairs, covering line provisioning, attainable bit rates, band plan and PSD limiting masks, and performance monitoring, filling a gap left by the general ADSL-LINE-MIB before a dedicated ADSL2/VDSL2 IETF MIB existed. It exposes upstream and downstream PSD limiting-mask tables with break-point definitions, plus VDSL2 status and profile/channel objects. It is used to monitor the software configuration and operational status of VDSL2 lines, including which spectral mask and channel profile is applied and the resulting line status, which helps identify misconfigured masks or profile mismatches that degrade attainable line rates rather than exposing chassis-level hardware sensors. It explicitly builds on and supplements the IETF ADSL-LINE-MIB (RFC 2662/RFC 3440) and the vendor's own PEA-ADSL-IPDSLAM module. It is deployed on Ericsson Diax IP DSLAM platforms delivering VDSL2 broadband access to subscribers. Engineers can download the PEA-VDSL-IPDSLAM file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in PEA-VDSL-IPDSLAM. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Ericsson Diax IP DSLAM
VDSL/VDSL2 access equipment

Monitoring Examples

An engineer would inspect vdslLineConfPhysVdslLimitingMaskDnTable/Entry and the corresponding Up table, checking limitingMaskDnBpToneIndex and limitingMaskDnBpPsd break points against the provisioned band plan to confirm the correct PSD mask is enforced per line. Polling vdsl2Status alongside vdsl2ProfileChannel reveals the active VDSL2 profile and current line state, useful for diagnosing lower-than-expected attainable rates. A mismatch between limitingMaskDnBypassOutbandPsdFilter settings and expected regulatory limits could explain interference complaints from a subscriber.

What Can Be Monitored

VDSL2 line status
PSD limiting mask break points (up/down)
VDSL2 profile/channel selection
band plan / outband PSD filter settings

Imported Objects

From ADSL-LINE-EXT-MIB

adslAtucThreshold15MinSesL	OBJECT-TYPE
adslAtucThreshold15MinUasL	OBJECT-TYPE
adslAturThreshold15MinSesL	OBJECT-TYPE
adslAturThreshold15MinUasL	OBJECT-TYPE

From ADSL-LINE-MIB

adslAtucChanCurrTxRate	OBJECT-TYPE
adslAtucChanIntervalNumber	OBJECT-TYPE
adslAtucIntervalNumber	OBJECT-TYPE
adslAtucThresh15MinESs	OBJECT-TYPE
adslAturChanCurrTxRate	OBJECT-TYPE
adslAturChanIntervalNumber	OBJECT-TYPE
adslAturIntervalNumber	OBJECT-TYPE
adslAturThresh15MinESs	OBJECT-TYPE
adslLineAlarmConfProfileEntry	OBJECT-TYPE
adslLineConfProfileEntry	OBJECT-TYPE

From DIESEL-SMI

peaIpDslam

OBJECT-IDENTITY

From PEA-ADSL-IPDSLAM

AdslPerfCurrDayCount
AdslPerfPrevDayCount
PerfCurrentCount
PerfIntervalCount

From PEA-BRIDGE-IPDSLAM

lineIndex

OBJECT-TYPE

From PEA-EQUIPMENT-IPDSLAM

errorCode	OBJECT-TYPE
messageId	OBJECT-TYPE

From PEM-STANDARD

eventTime	OBJECT-TYPE
eventTypePem	OBJECT-TYPE
managedObjectClass	OBJECT-TYPE
managedObjectInstance	OBJECT-TYPE
perceivedSeverity	OBJECT-TYPE
probableCause	OBJECT-TYPE
sequenceNumber	OBJECT-TYPE

From RFC1213-MIB

DisplayString

From SNMPv2-CONF

NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Gauge32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

TEXTUAL-CONVENTION
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
peaVdslIpDslam	1.3.6.1.4.1.193.72.300.80			The IP DSLAM software supports a number of standard and proprietary MIBs. This MIB module defines objects for the management of a pair of VDSL modems at each end of the VDSL line. For general DSL purposes the ADSL-LINE-MIB (RFC2662 and RFC3440) is used supplemented with the PEA-ADSL-IPDSLAM. The reason for this MIB module is that a new ADSL2/VDSL2 specific ADSL LINE MIB is yet not available from IETF.
vdslObjects	1.3.6.1.4.1.193.72.300.80.1
vdslLineConfPhysVdslLimitingMaskDnTable	1.3.6.1.4.1.193.72.300.80.1.1		not-accessible	This table contains information of LimitingMaskDn configuration
vdslLineConfPhysVdslLimitingMaskDnEntry	1.3.6.1.4.1.193.72.300.80.1.1.1		not-accessible	An entry in vdslLineConfPhysVdslLimitingMaskDnTable.
INT limitingMaskDnNoOfBreakPoints	1.3.6.1.4.1.193.72.300.80.1.1.1.1	INTEGER	read-write	Number of breakpoints in downstream mask
OCT limitingMaskDnBpToneIndex	1.3.6.1.4.1.193.72.300.80.1.1.1.2	OCTET STRING	read-write	Toneindexes for 32 breakpoints. The octet string has the format: [Bp0_Hi, Bp0_Low....Bp31_Hi, Bp31_Low] Valid range is [0, 4096]
OCT limitingMaskDnBpPsd	1.3.6.1.4.1.193.72.300.80.1.1.1.3	OCTET STRING	read-write	PSD level in 0.1 dBm/Hz for 32 breakpoints. Valid range is [0,-96] dBm/Hz. The octet string has the format: [Bp0_Hi, Bp0_Low....Bp31_Hi, Bp31_Low]
T/F limitingMaskDnBypassOutbandPsdFilter	1.3.6.1.4.1.193.72.300.80.1.1.1.4	TruthValue	read-write	If set, the extra filter will be bypassed at the expense of more OOB above 17.5MHz.
vdslLineConfPhysVdslLimitingMaskUpTable	1.3.6.1.4.1.193.72.300.80.1.2		not-accessible	This table contains information of LimitingMaskUp configuration
vdslLineConfPhysVdslLimitingMaskUpEntry	1.3.6.1.4.1.193.72.300.80.1.2.1		not-accessible	An entry in vdslLineConfPhysVdslLimitingMaskUpTable.
INT limitingMaskUpNoOfBreakPoints	1.3.6.1.4.1.193.72.300.80.1.2.1.1	INTEGER	read-write	Number of breakpoints in upstream mask
OCT limitingMaskUpBpToneIndex	1.3.6.1.4.1.193.72.300.80.1.2.1.2	OCTET STRING	read-write	Toneindexes for 16 breakpoints. The octet string has the format: [Bp0_Hi, Bp0_Low....Bp31_Hi, Bp31_Low] Valid range is [0, 4096]
OCT limitingMaskUpBpPsd	1.3.6.1.4.1.193.72.300.80.1.2.1.3	OCTET STRING	read-write	PSD level in 0.1 dBm/Hz for 16 breakpoints. Valid range is [0,-96] dBm/Hz. The octet string has the format: [Bp0_Hi, Bp0_Low....Bp31_Hi, Bp31_Low]
T/F limitingMaskUpUseIsdnTypeUS0	1.3.6.1.4.1.193.72.300.80.1.2.1.4	TruthValue	read-write	If set it indicates that an ISDN type US0 has to be negociated, else POTS type is used (default).
vdslLineConfPhysVdslBandPlanDnTable	1.3.6.1.4.1.193.72.300.80.1.3		not-accessible	This table contains information of BandPlanDn configuration
vdslLineConfPhysVdslBandPlanDnEntry	1.3.6.1.4.1.193.72.300.80.1.3.1		not-accessible	An entry in vdslLineConfPhysVdslBandPlanDnTable.
INT bandPlanDnNoOfToneGroups	1.3.6.1.4.1.193.72.300.80.1.3.1.1	INTEGER	read-write	Number of bands downstream
INT bandPlanDnToneGroups0StartTone	1.3.6.1.4.1.193.72.300.80.1.3.1.2	INTEGER	read-write	Start tone for this band
INT bandPlanDnToneGroups0EndTone	1.3.6.1.4.1.193.72.300.80.1.3.1.3	INTEGER	read-write	End tone for this band
INT bandPlanDnToneGroups1StartTone	1.3.6.1.4.1.193.72.300.80.1.3.1.4	INTEGER	read-write	Start tone for this band
INT bandPlanDnToneGroups1EndTone	1.3.6.1.4.1.193.72.300.80.1.3.1.5	INTEGER	read-write	End tone for this band
INT bandPlanDnToneGroups2StartTone	1.3.6.1.4.1.193.72.300.80.1.3.1.6	INTEGER	read-write	Start tone for this band
INT bandPlanDnToneGroups2EndTone	1.3.6.1.4.1.193.72.300.80.1.3.1.7	INTEGER	read-write	End tone for this band
vdslLineConfPhysVdslBandPlanUpTable	1.3.6.1.4.1.193.72.300.80.1.4		not-accessible	This table contains information of BandPlanUp configuration
vdslLineConfPhysVdslBandPlanUpEntry	1.3.6.1.4.1.193.72.300.80.1.4.1		not-accessible	An entry in vdslLineConfPhysVdslBandPlanUpTable.
INT bandPlanUpNoOfToneGroups	1.3.6.1.4.1.193.72.300.80.1.4.1.1	INTEGER	read-write	Number of bands downstream
INT bandPlanUpToneGroups0StartTone	1.3.6.1.4.1.193.72.300.80.1.4.1.2	INTEGER	read-write	Start tone for this band
INT bandPlanUpToneGroups0EndTone	1.3.6.1.4.1.193.72.300.80.1.4.1.3	INTEGER	read-write	End tone for this band
INT bandPlanUpToneGroups1StartTone	1.3.6.1.4.1.193.72.300.80.1.4.1.4	INTEGER	read-write	Start tone for this band
INT bandPlanUpToneGroups1EndTone	1.3.6.1.4.1.193.72.300.80.1.4.1.5	INTEGER	read-write	End tone for this band
INT bandPlanUpToneGroups2StartTone	1.3.6.1.4.1.193.72.300.80.1.4.1.6	INTEGER	read-write	Start tone for this band
INT bandPlanUpToneGroups2EndTone	1.3.6.1.4.1.193.72.300.80.1.4.1.7	INTEGER	read-write	End tone for this band
vdslLineConfPhysVdslInBandNotchesTable	1.3.6.1.4.1.193.72.300.80.1.5		not-accessible	This table contains information of InBandNotches configuration
vdslLineConfPhysVdslInBandNotchesEntry	1.3.6.1.4.1.193.72.300.80.1.5.1		not-accessible	An entry in vdslLineConfPhysVdslInBandNotchesTable.
INT inBandNotchesNoOfToneGroups	1.3.6.1.4.1.193.72.300.80.1.5.1.1	INTEGER	read-write	Number of InBand bands
INT inBandNotchesToneGroups0StartTone	1.3.6.1.4.1.193.72.300.80.1.5.1.2	INTEGER	read-write	Start tone for this band
INT inBandNotchesToneGroups0EndTone	1.3.6.1.4.1.193.72.300.80.1.5.1.3	INTEGER	read-write	End tone for this band
INT inBandNotchesToneGroups1StartTone	1.3.6.1.4.1.193.72.300.80.1.5.1.4	INTEGER	read-write	Start tone for this band
INT inBandNotchesToneGroups1EndTone	1.3.6.1.4.1.193.72.300.80.1.5.1.5	INTEGER	read-write	End tone for this band
INT inBandNotchesToneGroups2StartTone	1.3.6.1.4.1.193.72.300.80.1.5.1.6	INTEGER	read-write	Start tone for this band
INT inBandNotchesToneGroups2EndTone	1.3.6.1.4.1.193.72.300.80.1.5.1.7	INTEGER	read-write	End tone for this band
INT inBandNotchesToneGroups3StartTone	1.3.6.1.4.1.193.72.300.80.1.5.1.8	INTEGER	read-write	Start tone for this band
INT inBandNotchesToneGroups3EndTone	1.3.6.1.4.1.193.72.300.80.1.5.1.9	INTEGER	read-write	End tone for this band
INT inBandNotchesToneGroups4StartTone	1.3.6.1.4.1.193.72.300.80.1.5.1.10	INTEGER	read-write	Start tone for this band
INT inBandNotchesToneGroups4EndTone	1.3.6.1.4.1.193.72.300.80.1.5.1.11	INTEGER	read-write	End tone for this band
INT inBandNotchesToneGroups5StartTone	1.3.6.1.4.1.193.72.300.80.1.5.1.12	INTEGER	read-write	Start tone for this band
INT inBandNotchesToneGroups5EndTone	1.3.6.1.4.1.193.72.300.80.1.5.1.13	INTEGER	read-write	End tone for this band
INT inBandNotchesToneGroups6StartTone	1.3.6.1.4.1.193.72.300.80.1.5.1.14	INTEGER	read-write	Start tone for this band
INT inBandNotchesToneGroups6EndTone	1.3.6.1.4.1.193.72.300.80.1.5.1.15	INTEGER	read-write	End tone for this band
INT inBandNotchesToneGroups7StartTone	1.3.6.1.4.1.193.72.300.80.1.5.1.16	INTEGER	read-write	Start tone for this band
INT inBandNotchesToneGroups7EndTone	1.3.6.1.4.1.193.72.300.80.1.5.1.17	INTEGER	read-write	End tone for this band
vdslLineConfPhysVdslRfiNotchesTable	1.3.6.1.4.1.193.72.300.80.1.6		not-accessible	This table contains information of RfiNotches configuration
vdslLineConfPhysVdslRfiNotchesEntry	1.3.6.1.4.1.193.72.300.80.1.6.1		not-accessible	An entry in vdslLineConfPhysVdslRfiNotchesTable.
INT rfiNotchesNoOfToneGroups	1.3.6.1.4.1.193.72.300.80.1.6.1.1	INTEGER	read-write	Number of Rfi bands
INT rfiNotchesToneGroups0StartTone	1.3.6.1.4.1.193.72.300.80.1.6.1.2	INTEGER	read-write	Start tone for this Rfi band
INT rfiNotchesToneGroups0EndTone	1.3.6.1.4.1.193.72.300.80.1.6.1.3	INTEGER	read-write	End tone for this Rfi band
INT rfiNotchesToneGroups1StartTone	1.3.6.1.4.1.193.72.300.80.1.6.1.4	INTEGER	read-write	Start tone for this Rfi band
INT rfiNotchesToneGroups1EndTone	1.3.6.1.4.1.193.72.300.80.1.6.1.5	INTEGER	read-write	End tone for this Rfi band
INT rfiNotchesToneGroups2StartTone	1.3.6.1.4.1.193.72.300.80.1.6.1.6	INTEGER	read-write	Start tone for this Rfi band
INT rfiNotchesToneGroups2EndTone	1.3.6.1.4.1.193.72.300.80.1.6.1.7	INTEGER	read-write	End tone for this Rfi band
INT rfiNotchesToneGroups3StartTone	1.3.6.1.4.1.193.72.300.80.1.6.1.8	INTEGER	read-write	Start tone for this Rfi band
INT rfiNotchesToneGroups3EndTone	1.3.6.1.4.1.193.72.300.80.1.6.1.9	INTEGER	read-write	End tone for this Rfi band
INT rfiNotchesToneGroups4StartTone	1.3.6.1.4.1.193.72.300.80.1.6.1.10	INTEGER	read-write	Start tone for this Rfi band
INT rfiNotchesToneGroups4EndTone	1.3.6.1.4.1.193.72.300.80.1.6.1.11	INTEGER	read-write	End tone for this Rfi band
INT rfiNotchesToneGroups5StartTone	1.3.6.1.4.1.193.72.300.80.1.6.1.12	INTEGER	read-write	Start tone for this Rfi band
INT rfiNotchesToneGroups5EndTone	1.3.6.1.4.1.193.72.300.80.1.6.1.13	INTEGER	read-write	End tone for this Rfi band
INT rfiNotchesToneGroups6StartTone	1.3.6.1.4.1.193.72.300.80.1.6.1.14	INTEGER	read-write	Start tone for this Rfi band
INT rfiNotchesToneGroups6EndTone	1.3.6.1.4.1.193.72.300.80.1.6.1.15	INTEGER	read-write	End tone for this Rfi band
INT rfiNotchesToneGroups7StartTone	1.3.6.1.4.1.193.72.300.80.1.6.1.16	INTEGER	read-write	Start tone for this Rfi band
INT rfiNotchesToneGroups7EndTone	1.3.6.1.4.1.193.72.300.80.1.6.1.17	INTEGER	read-write	End tone for this Rfi band
INT rfiNotchesToneGroups8StartTone	1.3.6.1.4.1.193.72.300.80.1.6.1.18	INTEGER	read-write	Start tone for this Rfi band
INT rfiNotchesToneGroups8EndTone	1.3.6.1.4.1.193.72.300.80.1.6.1.19	INTEGER	read-write	End tone for this Rfi band
INT rfiNotchesToneGroups9StartTone	1.3.6.1.4.1.193.72.300.80.1.6.1.20	INTEGER	read-write	Start tone for this Rfi band
INT rfiNotchesToneGroups9EndTone	1.3.6.1.4.1.193.72.300.80.1.6.1.21	INTEGER	read-write	End tone for this Rfi band
INT rfiNotchesToneGroups10StartTone	1.3.6.1.4.1.193.72.300.80.1.6.1.22	INTEGER	read-write	Start tone for this Rfi band
INT rfiNotchesToneGroups10EndTone	1.3.6.1.4.1.193.72.300.80.1.6.1.23	INTEGER	read-write	End tone for this Rfi band
INT rfiNotchesToneGroups11StartTone	1.3.6.1.4.1.193.72.300.80.1.6.1.24	INTEGER	read-write	Start tone for this Rfi band
INT rfiNotchesToneGroups11EndTone	1.3.6.1.4.1.193.72.300.80.1.6.1.25	INTEGER	read-write	End tone for this Rfi band
INT rfiNotchesToneGroups12StartTone	1.3.6.1.4.1.193.72.300.80.1.6.1.26	INTEGER	read-write	Start tone for this Rfi band
INT rfiNotchesToneGroups12EndTone	1.3.6.1.4.1.193.72.300.80.1.6.1.27	INTEGER	read-write	End tone for this Rfi band
INT rfiNotchesToneGroups13StartTone	1.3.6.1.4.1.193.72.300.80.1.6.1.28	INTEGER	read-write	Start tone for this Rfi band
INT rfiNotchesToneGroups13EndTone	1.3.6.1.4.1.193.72.300.80.1.6.1.29	INTEGER	read-write	End tone for this Rfi band
INT rfiNotchesToneGroups14StartTone	1.3.6.1.4.1.193.72.300.80.1.6.1.30	INTEGER	read-write	Start tone for this Rfi band
INT rfiNotchesToneGroups14EndTone	1.3.6.1.4.1.193.72.300.80.1.6.1.31	INTEGER	read-write	End tone for this Rfi band
INT rfiNotchesToneGroups15StartTone	1.3.6.1.4.1.193.72.300.80.1.6.1.32	INTEGER	read-write	Start tone for this Rfi band
INT rfiNotchesToneGroups15EndTone	1.3.6.1.4.1.193.72.300.80.1.6.1.33	INTEGER	read-write	End tone for this Rfi band
vdslLineConfPhysVdslPboPsdUpTable	1.3.6.1.4.1.193.72.300.80.1.7		not-accessible	This table contains information of PboPsdUp configuration. Ai and Bi for three upstream bands, not counting US0. A and B are used by the upstream PBO algorithm as in G993.2, par. 7.2.4. The implementation is according to G.997.1 (third revision) section 7.3.1.2.14. The parameters will be substituted by XDSL2 Line MIB parameters.
vdslLineConfPhysVdslPboPsdUpEntry	1.3.6.1.4.1.193.72.300.80.1.7.1		not-accessible	An entry in vdslLineConfPhysVdslPboPsdUpTable.
INT vdslLineConfPhysVdslPboPsdUpNoOfToneGroups	1.3.6.1.4.1.193.72.300.80.1.7.1.1	INTEGER	read-write	Number of tone groups in the descriptor. Maximum is three. Must be equal to the number of upstream bands in the bandplan, not counting US0.
INT vdslLineConfPhysVdslPboPsdUpGroup0A	1.3.6.1.4.1.193.72.300.80.1.7.1.2	INTEGER	read-write	A value of US1. A/256 is the actual value and should be in [-40, -80.96]. G.997.1 name: UPBOPSD-pb (per band).
INT vdslLineConfPhysVdslPboPsdUpGroup1A	1.3.6.1.4.1.193.72.300.80.1.7.1.3	INTEGER	read-write	A value of US2. A/256 is the actual value and should be in [-40, -80.96]. G.997.1 name: UPBOPSD-pb (per band).
INT vdslLineConfPhysVdslPboPsdUpGroup2A	1.3.6.1.4.1.193.72.300.80.1.7.1.4	INTEGER	read-write	A value of US3. A/256 is the actual value and should be in [-40, -80.96]. Should be 0 if noOfToneGroups < 3. G.997.1 name: UPBOPSD-pb (per band).
INT vdslLineConfPhysVdslPboPsdUpGroup0B	1.3.6.1.4.1.193.72.300.80.1.7.1.5	INTEGER	read-write	A value of US1. B/256 is the actual value and should be in [-40, 0]. G.997.1 name: UPBOPSD-pb (per band).
INT vdslLineConfPhysVdslPboPsdUpGroup1B	1.3.6.1.4.1.193.72.300.80.1.7.1.6	INTEGER	read-write	A value of US2. B/256 is the actual value and should be in [-40, 0]. G.997.1 name: UPBOPSD-pb (per band).
INT vdslLineConfPhysVdslPboPsdUpGroup2B	1.3.6.1.4.1.193.72.300.80.1.7.1.7	INTEGER	read-write	A value of US3. B/256 is the actual value and should be in [-40, 0]. Should be 0 if noOfToneGroups < 3. G.997.1 name: UPBOPSD-pb (per band).
INT vdslLineConfPhysVdslPboPsdUpForceElectricalLength	1.3.6.1.4.1.193.72.300.80.1.7.1.10	INTEGER	read-write	If set, this electrical length (unit in 0.1 dB) will be enforced by the CO on the CPE, resulting in a predefined US PBO. If !=0, enforce US PBO corresponding to a line whose attenuation at 1MHz equals this number. Valid range [0,127] dB. A negative value of -1 mean: don't force the electrical length, but use the measured value instead. G.997.1 name: UPBOKL. G.997.1 name: UPBOKLF.
T/F vdslLineConfPhysVdslPboPsdUpAdvanced	1.3.6.1.4.1.193.72.300.80.1.7.1.15	TruthValue	read-write	Enables an alternative UPBOMASK calculation, which differs from the standard G.997.1 PBO mask calculation.
T/F vdslLineConfPhysVdslPboPsdUpDisable	1.3.6.1.4.1.193.72.300.80.1.7.1.20	TruthValue	read-write	Disable VDSL US power back off, forcing the CPE to use the max US PSD as template. Default not disabled.
vdslLineConfPhysVdslMiscVdslConfTable	1.3.6.1.4.1.193.72.300.80.1.8		not-accessible	This table contains information of MiscVdslConf configuration
vdslLineConfPhysVdslMiscVdslConfEntry	1.3.6.1.4.1.193.72.300.80.1.8.1		not-accessible	An entry in vdslLineConfPhysVdslMiscVdslConfTable.
INT miscVdslConfForceElectricalLength	1.3.6.1.4.1.193.72.300.80.1.8.1.1	INTEGER	read-write	If set, this electrical length (unit in 0.1 dB) will be enforced by the CO on the CPE, resulting in a predefined US PBO. If !=0, enforce US PBO corresponding to a line whose attenuation at 1MHz equals this number. Valid range [0,127] dB. A negative value of -1 mean: don't force the electrical length, but use the measured value instead, to be sent in O-UPDATE Substituted by: vdslLineConfPhysVdslPboPsdUpForceElectricalLength. Obsoleted from: EDA 4.0
INT miscVdslConfMaxTxPowerDn	1.3.6.1.4.1.193.72.300.80.1.8.1.2	INTEGER	read-write	Maximum allowed downstream transmit power. Unit is 0.1 dBm. Valid range [-25.6, 25.6] dBm.
T/F miscVdslConfDisableBitRateLimitation	1.3.6.1.4.1.193.72.300.80.1.8.1.3	TruthValue	read-write	Disables the rate limitation. Only to be used for test purposes. Note that disabling the limitation on more lines may lead to a crash.
T/F miscVdslConfDisableVdslUsPbo	1.3.6.1.4.1.193.72.300.80.1.8.1.4	TruthValue	read-write	Disable VDSL US power back off, forcing the CPE to use the max US PSD as template. Default not disabled. Substituted by: vdslLineConfPhysVdslPboPsdUpDisable. Obsoleted from: EDA 4.0
T/F miscVdslConfDynamicInterleaverUs	1.3.6.1.4.1.193.72.300.80.1.8.1.5	TruthValue	read-write	Enable support of dynamic change of interleaver depth in the upstream direction. Note: This field is specific to VDSL2 mode.
T/F miscVdslConfDynamicInterleaverDs	1.3.6.1.4.1.193.72.300.80.1.8.1.6	TruthValue	read-write	Enable support of dynamic change of interleaver depth in the downstream direction. Note: This field is specific to VDSL2 mode.
INT miscVdslConfDisableProfileBitmap	1.3.6.1.4.1.193.72.300.80.1.8.1.7	INTEGER	read-write	Bitmap of VDSL2 profiles to be masked The bits are ordered as in G994.1: bit0 = 8a bit6 = 17a Set the respective bit to disable the profile. Note: This field is specific to VDSL2 mode. Substituted by miscVdslConfEnableProfileBitmap which is standard compliant . Obsoleted from: EDA 4.0
BIT miscVdslConfEnableProfileBitmap	1.3.6.1.4.1.193.72.300.80.1.8.1.10	Bits	read-write	VDSL2 profiles to be allowed by the near-end xTU on this line. It is coded in a bit map representation (0 if not allowed, 1 if allowed) as defined in G.997.1 (third revision), section 7.3.1.1.11: NOTE that profile 30a is not supported in EDA. BIT PROFILE 7 G.993.2 Profile 8a. 6 G.993.2 Profile 8b. 5 G.993.2 Profile 8c. 4 G.993.2 Profile 8d. 3 G.993.2 Profile 12a. 2 G.993.2 Profile 12b. 1 G.993.2 Profile 17a. 0 G.993.2 Profile 30a. Valid from: EDA 4.0
INT miscVdslConfigStandardLimitMask	1.3.6.1.4.1.193.72.300.80.1.8.1.15	INTEGER	read-write	Proprietary interface for selecting a predefined standard compliant Bandplan & LimitMask. NOTE that selecting a predefined BandPlan & LimitMask overrides the vdslLineConfPhysVdslLimitingMaskDn/Up and the vdslLineConfPhysVdslBandPlanDn/Up parameters. To avoid this (e.g. for using a custom BandPlan and/or LimitMask), you should select the value here. Valid from: EDA 4.0
vdslVtucProprietaryChanXTable	1.3.6.1.4.1.193.72.300.80.1.9		not-accessible	VDSL VTU-C Proprietary Channel Extension Table.
vdslVtucProprietaryChanXEntry	1.3.6.1.4.1.193.72.300.80.1.9.1		not-accessible	An entry in the vdslVtucProprietaryChanXEntry.
U32 vdslVtucProprietaryChanXI	1.3.6.1.4.1.193.72.300.80.1.9.1.1	Unsigned32	read-only	I is the interleaver block length. Note: This parameter applies to VDSL2 protocols only.
U32 vdslVtucProprietaryChanXG	1.3.6.1.4.1.193.72.300.80.1.9.1.2	Unsigned32	read-only	G is the total number of overhead octets in an overhead superframe. Note: This parameter applies to VDSL2 protocols
U32 vdslVtucProprietaryChanXU	1.3.6.1.4.1.193.72.300.80.1.9.1.3	Unsigned32	read-only	U is the total number of overhead subframes per overhead superframe. Note: This parameter applies to VDSL2 protocols only.
U32 vdslVtucProprietaryChanXF	1.3.6.1.4.1.193.72.300.80.1.9.1.4	Unsigned32	read-only	F is the number of overhead frames in the overhead superframe. Note: This parameter applies to VDSL2 protocols only.
INT vdslVtucProprietaryChanXTpsTcTypeB0	1.3.6.1.4.1.193.72.300.80.1.9.1.10	INTEGER	read-write	The TPC-TC currently used for bearer channel B0. The two channels must use the same TPS-TC configuration, if enabled.
INT vdslVtucProprietaryChanXTpsTcTypeB1	1.3.6.1.4.1.193.72.300.80.1.9.1.15	INTEGER	read-write	The TPC-TC currently used for bearer channel B1. The two channels must use the same TPS-TC configuration, if enabled.
vdslVturProprietaryChanXTable	1.3.6.1.4.1.193.72.300.80.1.10		not-accessible	VDSL VTU-R Proprietary Channel Extension Table.
vdslVturProprietaryChanXEntry	1.3.6.1.4.1.193.72.300.80.1.10.1		not-accessible	An entry in the vdslVturProprietaryChanXTable.
U32 vdslVturProprietaryChanXI	1.3.6.1.4.1.193.72.300.80.1.10.1.1	Unsigned32	read-only	I is the interleaver block length. Note: This parameter applies to VDSL2 protocols only.
U32 vdslVturProprietaryChanXG	1.3.6.1.4.1.193.72.300.80.1.10.1.2	Unsigned32	read-only	G is the total number of overhead octets in an overhead superframe. Note: This parameter applies to VDSL2 protocols
U32 vdslVturProprietaryChanXU	1.3.6.1.4.1.193.72.300.80.1.10.1.3	Unsigned32	read-only	U is the total number of overhead subframes per overhead superframe. Note: This parameter applies to VDSL2 protocols only.
U32 vdslVturProprietaryChanXF	1.3.6.1.4.1.193.72.300.80.1.10.1.4	Unsigned32	read-only	F is the number of overhead frames in the overhead superframe. Note: This parameter applies to VDSL2 protocols only.
vdslLineStatusPhysVdslBandPlanDnTable	1.3.6.1.4.1.193.72.300.80.1.11		not-accessible	This table contains status information of the actual BandPlanDn
vdslLineStatusPhysVdslBandPlanDnEntry	1.3.6.1.4.1.193.72.300.80.1.11.1		not-accessible	An entry in vdslLineStatusPhysVdslBandPlanDnTable.
INT statusBandPlanDnNoOfToneGroups	1.3.6.1.4.1.193.72.300.80.1.11.1.1	INTEGER	read-only	Actual number of bands downstream
INT statusBandPlanDnToneGroups0StartTone	1.3.6.1.4.1.193.72.300.80.1.11.1.2	INTEGER	read-only	Actual start tone for this band
INT statusBandPlanDnToneGroups0EndTone	1.3.6.1.4.1.193.72.300.80.1.11.1.3	INTEGER	read-only	Actual end tone for this band
INT statusBandPlanDnToneGroups1StartTone	1.3.6.1.4.1.193.72.300.80.1.11.1.4	INTEGER	read-only	Actual start tone for this statusBand
INT statusBandPlanDnToneGroups1EndTone	1.3.6.1.4.1.193.72.300.80.1.11.1.5	INTEGER	read-only	Actual end tone for this band
INT statusBandPlanDnToneGroups2StartTone	1.3.6.1.4.1.193.72.300.80.1.11.1.6	INTEGER	read-only	Actual start tone for this band
INT statusBandPlanDnToneGroups2EndTone	1.3.6.1.4.1.193.72.300.80.1.11.1.7	INTEGER	read-only	Actual end tone for this band
vdslLineStatusPhysVdslBandPlanUpTable	1.3.6.1.4.1.193.72.300.80.1.12		not-accessible	This table contains status information of the actual BandPlanUp
vdslLineStatusPhysVdslBandPlanUpEntry	1.3.6.1.4.1.193.72.300.80.1.12.1		not-accessible	An entry in vdslLineStatusPhysVdslBandPlanUpTable.
INT statusBandPlanUpNoOfToneGroups	1.3.6.1.4.1.193.72.300.80.1.12.1.1	INTEGER	read-only	Actual number of bands downstream
INT statusBandPlanUpToneGroups0StartTone	1.3.6.1.4.1.193.72.300.80.1.12.1.2	INTEGER	read-only	Actual start tone for this band
INT statusBandPlanUpToneGroups0EndTone	1.3.6.1.4.1.193.72.300.80.1.12.1.3	INTEGER	read-only	Actual end tone for this band
INT statusBandPlanUpToneGroups1StartTone	1.3.6.1.4.1.193.72.300.80.1.12.1.4	INTEGER	read-only	Actual start tone for this band
INT statusBandPlanUpToneGroups1EndTone	1.3.6.1.4.1.193.72.300.80.1.12.1.5	INTEGER	read-only	Actual end tone for this band
INT statusBandPlanUpToneGroups2StartTone	1.3.6.1.4.1.193.72.300.80.1.12.1.6	INTEGER	read-only	Actual start tone for this band
INT statusBandPlanUpToneGroups2EndTone	1.3.6.1.4.1.193.72.300.80.1.12.1.7	INTEGER	read-only	Actual end tone for this band
vdslLineConfPhysVdslPboPsdDnTable	1.3.6.1.4.1.193.72.300.80.1.20		not-accessible	This table provides a set of line configuration parameters to generate a modified downstream PSD mask for Downstream Power Back-Off - Shaped (DPBOSHAPED). The implementation is according to G.997.1 (third revision) section 7.3.1.2.13. The parameters will be substituted by XDSL2 Line MIB parameters.
vdslLineConfPhysVdslPboPsdDnEntry	1.3.6.1.4.1.193.72.300.80.1.20.1		not-accessible	An entry in vdslLineConfPhysVdslPboPsdDnTable.
INT vdslLineConfPhysVdslPboPsdDnEsel	1.3.6.1.4.1.193.72.300.80.1.20.1.5	INTEGER	read-write	This configuration parameter defines the assumed electrical length of cables (E-side cables) connecting exchange based DSL services to a remote flexibility point (cabinet), that hosts the xTU-C that is subject to spectrally shaped downstream power back-off depending on this length. For this parameter the electrical length is defined as the loss (in dB) of an equivalent length of hypothetical cable at a reference frequency defined by the network operator or in spectrum management regulations. DPBOESEL shall be coded as an unsigned integer representing an electrical length from 0 dB to 255.5 dB in steps of 0.5 dB. All values in the range are valid. If DPBOESEL is set to zero, the DPBO in this section shall be disabled. G.997.1 name: DPBOESEL. Valid from: EDA 4.0
INT vdslLineConfPhysVdslPboPsdDnEscmA	1.3.6.1.4.1.193.72.300.80.1.20.1.10	INTEGER	read-write	This configuration parameter is used to define a cable model in terms of three scalars DPBOESCMA, DPBOESCMB and DPBOESCMC that shall be used to describe the frequency dependent loss of E-side cables. Parameters DPBOESCMA, DPBOESCMB, DPBOESCMC shall be coded as unsigned integers representing a scalar value from -1 to 1.5 in steps of 1/256. All values in the range are valid. G.997.1 name: DPBOESCMA. Valid from: EDA 4.0
INT vdslLineConfPhysVdslPboPsdDnEscmB	1.3.6.1.4.1.193.72.300.80.1.20.1.15	INTEGER	read-write	This configuration parameter is used to define a cable model in terms of three scalars DPBOESCMA, DPBOESCMB and DPBOESCMC that shall be used to describe the frequency dependent loss of E-side cables. Parameters DPBOESCMA, DPBOESCMB, DPBOESCMC shall be coded as unsigned integers representing a scalar value from -1 to 1.5 in steps of 1/256. All values in the range are valid. G.997.1 name: DPBOESCMB. Valid from: EDA 4.0
INT vdslLineConfPhysVdslPboPsdDnEscmC	1.3.6.1.4.1.193.72.300.80.1.20.1.20	INTEGER	read-write	This configuration parameter is used to define a cable model in terms of three scalars DPBOESCMA, DPBOESCMB and DPBOESCMC that shall be used to describe the frequency dependent loss of E-side cables. Parameters DPBOESCMA, DPBOESCMB, DPBOESCMC shall be coded as unsigned integers representing a scalar value from -1 to 1.5 in steps of 1/256. All values in the range are valid. G.997.1 name: DPBOESCMC. Valid from: EDA 4.0
INT vdslLineConfPhysVdslPboPsdDnFmin	1.3.6.1.4.1.193.72.300.80.1.20.1.25	INTEGER	read-write	Defines the minimum frequency from which the DPBO shall be applied. It ranges from 0 kHz to 8832 kHz in steps of 4.3125 kHz. G.997.1 name: DPBOFMIN. Valid from: EDA 4.0
INT vdslLineConfPhysVdslPboPsdDnFmax	1.3.6.1.4.1.193.72.300.80.1.20.1.30	INTEGER	read-write	Defines the maximum frequency at which DPBO may be applied. It ranges from 138 kHz to 29997.75 kHz in steps of 4.3125 kHz. G.997.1 name: DPBOFMAX. Valid from: EDA 4.0
INT vdslLineConfPhysVdslPboPsdDnMus	1.3.6.1.4.1.193.72.300.80.1.20.1.35	INTEGER	read-write	Defines the assumed Minimum Usable receive PSD mask (in dBm/Hz) for exchange based services, used to modify parameter DPBOFMAX. It shall be coded as an integer representing a PSD mask level from -127.5 dBm/Hz to 0 dBm/Hz in steps of 0.5 dB. All values in the range are valid. NOTE - The PSD mask level is 3.5 dB above the signal PSD level G.997.1 name: DPBOFMUS. Valid from: EDA 4.0
T/F vdslLineConfPhysVdslPboPsdDnAdvanced	1.3.6.1.4.1.193.72.300.80.1.20.1.40	TruthValue	read-write	Enables an alternative downstream Power Back-Off, which differs from the standard G.997.1 PBO calculation.
INT vdslLineConfPhysVdslPboPsdDnEselMin	1.3.6.1.4.1.193.72.300.80.1.20.1.45	INTEGER	read-write	This configuration parameter defines the minimum value of all trunk line losses of the cable distributors served (including the KVz at the DSLAM site). This parameter is not G.997.1 compliant and has only effect when vdslLineConfPhysVdslPboPsdDnAdvanced is enabled. Valid from: EDA 4.0
vdslLineConfPhysVdslMibMaskDsTable	1.3.6.1.4.1.193.72.300.80.1.25		not-accessible	This table contains information of MibMaskDs configuration in accordance with to G.997.1 section 7.3.1.2.9
vdslLineConfPhysVdslMibMaskDsEntry	1.3.6.1.4.1.193.72.300.80.1.25.1		not-accessible	An entry in vdslLineConfPhysVdslMibMaskDsTable.
INT mibMaskDsNoOfBreakPoints	1.3.6.1.4.1.193.72.300.80.1.25.1.5	INTEGER	read-write	Number of breakpoints in downstream mask. Each breakpoint is defined by a subcarrier index (mibMaskDsBpToneIndex) and a PSD level (mibMaskDsBpPsd). G.997.1 name: PSDMASKds. Valid from: EDA 4.0
OCT mibMaskDsBpToneIndex	1.3.6.1.4.1.193.72.300.80.1.25.1.10	OCTET STRING	read-write	Toneindexes for 32 breakpoints. Each ToneIndex is 2 octets. The octet string has the format: [Bp0_Hi, Bp0_Low....Bp31_Hi, Bp31_Low] Valid range is [0, 4096]. G.997.1 name: PSDMASKds. Valid from: EDA 4.0
OCT mibMaskDsBpPsd	1.3.6.1.4.1.193.72.300.80.1.25.1.15	OCTET STRING	read-write	PSD level in 0.1 dBm/Hz for 32 breakpoints. Each BpPsd has to octets. The octet string has the format: [Bp0_Hi, Bp0_Low....Bp31_Hi, Bp31_Low] Valid range is [0,-96] dBm/Hz. G.997.1 name: PSDMASKds. Valid from: EDA 4.0
vdslLineConfPhysVdslMibMaskUsTable	1.3.6.1.4.1.193.72.300.80.1.30		not-accessible	This table contains information of MibMaskUs configuration in accordance with to G.997.1 section 7.3.1.2.12
vdslLineConfPhysVdslMibMaskUsEntry	1.3.6.1.4.1.193.72.300.80.1.30.1		not-accessible	An entry in vdslLineConfPhysVdslMibMaskUsTable.
INT mibMaskUsNoOfBreakPoints	1.3.6.1.4.1.193.72.300.80.1.30.1.5	INTEGER	read-write	Number of breakpoints in upstream mask. Each breakpoint is defined by a subcarrier index (mibMaskUsBpToneIndex) and a PSD level (mibMaskUsBpPsd). G.997.1 name: PSDMASKus. Valid from: EDA 4.0
OCT mibMaskUsBpToneIndex	1.3.6.1.4.1.193.72.300.80.1.30.1.10	OCTET STRING	read-write	Toneindexes for 16 breakpoints. Each ToneIndex is 2 octets. The octet string has the format: [Bp0_Hi, Bp0_Low....Bp15_Hi, Bp15_Low] Valid range is [0, 4096]. G.997.1 name: PSDMASKus. Valid from: EDA 4.0
OCT mibMaskUsBpPsd	1.3.6.1.4.1.193.72.300.80.1.30.1.15	OCTET STRING	read-write	PSD level in 0.1 dBm/Hz for 16 breakpoints. Each BpPsd has to octets. The octet string has the format: [Bp0_Hi, Bp0_Low....Bp15_Hi, Bp15_Low] Valid range is [0,-96] dBm/Hz. G.997.1 name: PSDMASKus. Valid from: EDA 4.0
vdslProprietaryLineConfProfileXTable	1.3.6.1.4.1.193.72.300.80.1.35		not-accessible	VDSL Proprietary Line Configuration Profile Extention Table.
vdslProprietaryLineConfProfileXEntry	1.3.6.1.4.1.193.72.300.80.1.35.1		not-accessible	An entry in the vdslLineConfProfileXTable.
INT vdslVtucProprietaryConfXTpsTcType	1.3.6.1.4.1.193.72.300.80.1.35.1.5	INTEGER	read-write	Configure allowed traffic type: ATM, PTM or both.
T/F vdslVtucProprietaryConfXPreemtionAllowedB0	1.3.6.1.4.1.193.72.300.80.1.35.1.10	TruthValue	read-write	If True the subscriber is allowed to send preemptive traffic frames on bearer channel B0. The value can be either True(1) or False(2).
T/F vdslVtucProprietaryConfXPreemtionAllowedB1	1.3.6.1.4.1.193.72.300.80.1.35.1.15	TruthValue	read-write	If True the subscriber is allowed to send preemptive traffic frames on bearer channel B1. The value can be either True(1) or False(2).
vdslVtucChanIntervalXTable	1.3.6.1.4.1.193.72.300.80.1.40		not-accessible	This table provides extra information in relation to the xdslXtucChanIntervalTable for each VTU-C channel's performance collection interval. XDSL channel interfaces are those ifEntries where ifType is equal to Interleave(124) or Fast(125). Performance Data Interval number 1 is the the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are optional. Interval number 1 is the only interval used currently.
vdslVtucChanIntervalXEntry	1.3.6.1.4.1.193.72.300.80.1.40.1		not-accessible	An entry in the vdslVtucChanIntervalXTable.
NUM vdslVtucChanIntervalXPtmCrcErrors	1.3.6.1.4.1.193.72.300.80.1.40.1.5	PerfIntervalCount	read-only	Count of all PTM CRC errors on PTM non-preemtive traffic received on this channel during this interval.
NUM vdslVtucChanIntervalXPtmCrcErrorsP	1.3.6.1.4.1.193.72.300.80.1.40.1.10	PerfIntervalCount	read-only	Count of all PTM CRC errors on PTM preemtive traffic received on this channel during this interval.
NUM vdslVtucChanIntervalXPtmCv	1.3.6.1.4.1.193.72.300.80.1.40.1.15	PerfIntervalCount	read-only	Count of all PTM Coding violations on PTM non-preemtive traffic received on this channel during this interval.
NUM vdslVtucChanIntervalXPtmCvP	1.3.6.1.4.1.193.72.300.80.1.40.1.20	PerfIntervalCount	read-only	Count of all PTM Coding violations on PTM preemtive traffic received on this channel during this interval.
vdslVturChanIntervalXTable	1.3.6.1.4.1.193.72.300.80.1.45		not-accessible	This table provides extra information in relation to the xdslXturChanIntervalTable for each VTU-R channel's performance collection interval. XDSL channel interfaces are those ifEntries where ifType is equal to Interleave(124) or Fast(125). Performance Data Interval number 1 is the the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are optional. Interval number 1 is the only interval used currently.
vdslVturChanIntervalXEntry	1.3.6.1.4.1.193.72.300.80.1.45.1		not-accessible	An entry in the vdslVturChanIntervalXTable.
NUM vdslVturChanIntervalXPtmCrcErrors	1.3.6.1.4.1.193.72.300.80.1.45.1.5	PerfIntervalCount	read-only	Count of all PTM CRC errors on PTM non-preemtive traffic received on this channel during this interval.
NUM vdslVturChanIntervalXPtmCrcErrorsP	1.3.6.1.4.1.193.72.300.80.1.45.1.10	PerfIntervalCount	read-only	Count of all PTM CRC errors on PTM preemtive traffic received on this channel during this interval.
NUM vdslVturChanIntervalXPtmCv	1.3.6.1.4.1.193.72.300.80.1.45.1.15	PerfIntervalCount	read-only	Count of all PTM Coding violations on PTM non-preemtive traffic received on this channel during this interval.
NUM vdslVturChanIntervalXPtmCvP	1.3.6.1.4.1.193.72.300.80.1.45.1.20	PerfIntervalCount	read-only	Count of all PTM Coding violations on PTM preemtive traffic received on this channel during this interval.
vdslVtucChanPerfDataXTable	1.3.6.1.4.1.193.72.300.80.1.50		not-accessible	This table provides extra VTU-C channel information in relation to the adslAtucChanPerfDataTable. VDSL2 channel interfaces are those ifEntries where ifType is equal to Interleave(124) or Fast(125).
vdslVtucChanPerfDataXEntry	1.3.6.1.4.1.193.72.300.80.1.50.1		not-accessible	An entry in the vdslVtucChanPerfDataXTable.
PER vdslVtucChanIntervalXCurr15MinPtmCrcErrors	1.3.6.1.4.1.193.72.300.80.1.50.1.5	PerfCurrentCount	read-only	Count of all PTM CRC errors on PTM non-preemtive traffic received on this channel within the current 15 minute interval.
ADS vdslVtucChanIntervalXCurr1DayPtmCrcErrors	1.3.6.1.4.1.193.72.300.80.1.50.1.10	AdslPerfCurrDayCount	read-only	Count of all PTM CRC errors on PTM non-preemtive traffic received on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.
ADS vdslVtucChanIntervalXPrev1DayPtmCrcErrors	1.3.6.1.4.1.193.72.300.80.1.50.1.15	AdslPerfPrevDayCount	read-only	Count of all PTM CRC errors on PTM non-preemtive traffic blocks received on this channel within the most recent previous 1-day period.
PER vdslVtucChanIntervalXCurr15MinPtmCrcErrorsP	1.3.6.1.4.1.193.72.300.80.1.50.1.20	PerfCurrentCount	read-only	Count of all PTM CRC errors on PTM preemtive traffic received on this channel within the current 15 minute interval.
ADS vdslVtucChanIntervalXCurr1DayPtmCrcErrorsP	1.3.6.1.4.1.193.72.300.80.1.50.1.25	AdslPerfCurrDayCount	read-only	Count of all PTM CRC errors on PTM preemtive traffic received on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.
ADS vdslVtucChanIntervalXPrev1DayPtmCrcErrorsP	1.3.6.1.4.1.193.72.300.80.1.50.1.30	AdslPerfPrevDayCount	read-only	Count of all PTM CRC errors on PTM preemtive traffic blocks received on this channel within the most recent previous 1-day period.
PER vdslVtucChanIntervalXCurr15MinPtmCv	1.3.6.1.4.1.193.72.300.80.1.50.1.35	PerfCurrentCount	read-only	Count of all PTM Coding violations on PTM non-preemtive received on this channel within the current 15 minute interval.
ADS vdslVtucChanIntervalXCurr1DayPtmCv	1.3.6.1.4.1.193.72.300.80.1.50.1.40	AdslPerfCurrDayCount	read-only	Count of all PTM Coding violations on PTM non-preemtive received on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.
ADS vdslVtucChanIntervalXPrev1DayPtmCv	1.3.6.1.4.1.193.72.300.80.1.50.1.45	AdslPerfPrevDayCount	read-only	Count of all PTM Coding violations on PTM non-preemtive blocks received on this channel within the most recent previous 1-day period.
PER vdslVtucChanIntervalXCurr15MinPtmCvP	1.3.6.1.4.1.193.72.300.80.1.50.1.50	PerfCurrentCount	read-only	Count of all PTM Coding violations on PTM preemtive received on this channel within the current 15 minute interval.
ADS vdslVtucChanIntervalXCurr1DayPtmCvP	1.3.6.1.4.1.193.72.300.80.1.50.1.55	AdslPerfCurrDayCount	read-only	Count of all PTM Coding violations on PTM preemtive received on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.
ADS vdslVtucChanIntervalXPrev1DayPtmCvP	1.3.6.1.4.1.193.72.300.80.1.50.1.60	AdslPerfPrevDayCount	read-only	Count of all PTM Coding violations on PTM preemtive blocks received on this channel within the most recent previous 1-day period.
vdslVturChanPerfDataXTable	1.3.6.1.4.1.193.72.300.80.1.55		not-accessible	This table provides extra VTU-R channel information in relation to the adslAtucChanPerfDataTable. VDSL2 channel interfaces are those ifEntries where ifType is equal to Interleave(124) or Fast(125).
vdslVturChanPerfDataXEntry	1.3.6.1.4.1.193.72.300.80.1.55.1		not-accessible	An entry in the vdslVturChanPerfDataXTable.
PER vdslVturChanIntervalXCurr15MinPtmCrcErrors	1.3.6.1.4.1.193.72.300.80.1.55.1.5	PerfCurrentCount	read-only	Count of all PTM CRC errors on PTM non-preemtive traffic received on this channel within the current 15 minute interval.
ADS vdslVturChanIntervalXCurr1DayPtmCrcErrors	1.3.6.1.4.1.193.72.300.80.1.55.1.10	AdslPerfCurrDayCount	read-only	Count of all PTM CRC errors on PTM non-preemtive traffic received on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.
ADS vdslVturChanIntervalXPrev1DayPtmCrcErrors	1.3.6.1.4.1.193.72.300.80.1.55.1.15	AdslPerfPrevDayCount	read-only	Count of all PTM CRC errors on PTM non-preemtive traffic blocks received on this channel within the most recent previous 1-day period.
PER vdslVturChanIntervalXCurr15MinPtmCrcErrorsP	1.3.6.1.4.1.193.72.300.80.1.55.1.20	PerfCurrentCount	read-only	Count of all PTM CRC errors on PTM preemtive traffic received on this channel within the current 15 minute interval.
ADS vdslVturChanIntervalXCurr1DayPtmCrcErrorsP	1.3.6.1.4.1.193.72.300.80.1.55.1.25	AdslPerfCurrDayCount	read-only	Count of all PTM CRC errors on PTM preemtive traffic received on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.
ADS vdslVturChanIntervalXPrev1DayPtmCrcErrorsP	1.3.6.1.4.1.193.72.300.80.1.55.1.30	AdslPerfPrevDayCount	read-only	Count of all PTM CRC errors on PTM preemtive traffic blocks received on this channel within the most recent previous 1-day period.
PER vdslVturChanIntervalXCurr15MinPtmCv	1.3.6.1.4.1.193.72.300.80.1.55.1.35	PerfCurrentCount	read-only	Count of all PTM Coding violations on PTM non-preemtive received on this channel within the current 15 minute interval.
ADS vdslVturChanIntervalXCurr1DayPtmCv	1.3.6.1.4.1.193.72.300.80.1.55.1.40	AdslPerfCurrDayCount	read-only	Count of all PTM Coding violations on PTM non-preemtive received on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.
ADS vdslVturChanIntervalXPrev1DayPtmCv	1.3.6.1.4.1.193.72.300.80.1.55.1.45	AdslPerfPrevDayCount	read-only	Count of all PTM Coding violations on PTM non-preemtive blocks received on this channel within the most recent previous 1-day period.
PER vdslVturChanIntervalXCurr15MinPtmCvP	1.3.6.1.4.1.193.72.300.80.1.55.1.50	PerfCurrentCount	read-only	Count of all PTM Coding violations on PTM preemtive received on this channel within the current 15 minute interval.
ADS vdslVturChanIntervalXCurr1DayPtmCvP	1.3.6.1.4.1.193.72.300.80.1.55.1.55	AdslPerfCurrDayCount	read-only	Count of all PTM Coding violations on PTM preemtive received on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.
ADS vdslVturChanIntervalXPrev1DayPtmCvP	1.3.6.1.4.1.193.72.300.80.1.55.1.60	AdslPerfPrevDayCount	read-only	Count of all PTM Coding violations on PTM preemtive blocks received on this channel within the most recent previous 1-day period.
vdslLineMiscPhysStatusTable	1.3.6.1.4.1.193.72.300.80.1.60		not-accessible	This table contains information of MiscVdslConf configuration
vdslLineMiscPhysStatusEntry	1.3.6.1.4.1.193.72.300.80.1.60.1		not-accessible	An entry in vdslLineMiscPhysStatusTable.
BIT miscPhysStatusVdslProfileBitmap	1.3.6.1.4.1.193.72.300.80.1.60.1.5	Bits	read-only	VDSL2 profiles to be allowed by the near-end xTU on this line. It is coded in a bit map representation (0 if not allowed, 1 if allowed) as defined in G.997.1 (third revision), section 7.3.1.1.11: NOTE that profile 30a is not supported in EDA. BIT PROFILE 7 G.993.2 Profile 8a. 6 G.993.2 Profile 8b. 5 G.993.2 Profile 8c. 4 G.993.2 Profile 8d. 3 G.993.2 Profile 12a. 2 G.993.2 Profile 12b. 1 G.993.2 Profile 17a. 0 G.993.2 Profile 30a. Valid from: EDA 4.0
vdsl2Status	1.3.6.1.4.1.193.72.300.80.2
vdsl2SCStatusTable	1.3.6.1.4.1.193.72.300.80.2.5		not-accessible	The table vdsl2SCStatusTable contains status parameters of VDSL2/ADSL/ADSL2 and ADSL2+ sub-carriers. This table contains live data from equipment. This table is copied from draft-ietf-adslmib-vdsl2-01.txt, to secure a smooth migration to the VDSL2-LINE MIB when this MIB is approved.
vdsl2SCStatusEntry	1.3.6.1.4.1.193.72.300.80.2.5.1		not-accessible	The table Hfvdsl2SCStatusEntry contains status parameters of VDSL2/ADSL/ADSL2 and ADSL2+ sub-carriers. One index of this table is an interface index where the interface has an ifType of vdsl2(xxx). A second index of this table is the transmission direction. A third index identifies the specific segment of the sub-carriers status addressed.
VDS vdsl2SCStatusDirection	1.3.6.1.4.1.193.72.300.80.2.5.1.1	Vdsl2Direction	not-accessible	The direction of the sub-carrier either upstream or downstream
U32 vdsl2SCStatusSegment	1.3.6.1.4.1.193.72.300.80.2.5.1.2	Unsigned32	not-accessible	The segment of the sub-carriers status information provided by this row. Several status parameters in this table are retrieved in segments. The first segment of the status information is retrieved with vdsl2SCStatusSegment=1, the second segment is retrieved with vdsl2SCStatusSegment=2, and so on. When any status parameter is retrieved in n segments where n<8) then, for that parameter, GET operations for the rest segment numbers (n+1 to 8) are responded with a value that indicates: No measurement could be done. This table is from draft-ietf-adslmib-vdsl2-01.txt.
OCT vdsl2SCStatusSnr	1.3.6.1.4.1.193.72.300.80.2.5.1.5	OCTET STRING	read-only	The SNR Margin per sub-carrier group, expressing the ratio between the received signal power and received noise power per sub-scriber group. It is an array of 512 octets, designed for supporting up to 512 (downstream) sub-carriers groups and can be retrieved in a single segment. The number of utilized octets on downstream direction depends on NSds, and on upstream direction it depends on NSus. This value is referred here as NS. Octet i (0 <= i < NS) is set to a value in the range 0 to 254 to indicate that the respective downstream or upstream sub- carrier group i has SNR of: (-32 + Xdsl2SubcarrierSnr(i)/2) in dB (i.e., -32 to 95dB). The special value 255 means that no measurement could be done for the sub-carrier group because it is out of the PSD mask passband or that the noise PSD is out of range to be represented. Each value in this array is 8 bits wide. This table is from draft-ietf-adslmib-vdsl2-01.txt.
OCT vdsl2SCStatusBitsAlloc	1.3.6.1.4.1.193.72.300.80.2.5.1.10	OCTET STRING	read-only	The bits allocation per sub-carrier. An array of 256 octets (512 nibbles), designed for supporting up to 512 (downstream) sub-carriers. When more then 512 sub-carriers are supported, the status information is reported through multiple (up to 8) segments. The first segment is then used for the first 512 sub-carriers. The second segment is used for the sub-carriers 512 to 1023 and so on. The aggregate number of utilized nibbles on downstream direction (in all segments) depends on NSds, and on upstream direction it depends on NSus. This value is referred here as NS. The segment number is in vdsl2SCStatusSegment. Nibble i (0 <= i < MIN(NS-(segment-1)512,512)) in each segment is set to a value in the range 0 to 15 to indicate that the respective downstream or upstream sub-carrier j (j=(segement-1)512+i) has the same amount of bits allocation. This table is from draft-ietf-adslmib-vdsl2-01.txt.
OCT vdsl2SCStatusGainAlloc	1.3.6.1.4.1.193.72.300.80.2.5.1.15	OCTET STRING	read-only	The gain allocation per sub-carrier. An array of 512 16-bits values, designed for supporting up to 512 (downstream) sub- carriers. When more then 512 sub-carriers are supported, the status information is reported through multiple (up to 8) segments. The first segment is then used for the first 512 sub-carriers. The second segment is used for the sub-carriers 512 to 1023 and so on. The aggregate number of utilized octets on downstream direction depends on NSds, and on upstream direction it depends on NSus. This value is referred here as NS. The segment number is in vdsl2SCStatusSegment. Value i (0 <= i < MIN(NS-(segment-1)512,512)) in each segment is set to a value in the range 0 to 4093 to indicate that the respective downstream or upstream sub-carrier j (j=(segement-1)512+i) has the same amount of gain value. The gain value is represented as a multiple of 1/512 on linear scale. Each value in this array is 16 bits wide and is stored in big endian format. This table is from draft-ietf-adslmib-vdsl2-01.txt.
vdsl2ProfileChannel	1.3.6.1.4.1.193.72.300.80.3
vdsl2ChConfProfileTable	1.3.6.1.4.1.193.72.300.80.3.1		not-accessible	The table vdsl2ChConfProfileTable contains DSL channel profile configuration. Entries in this table MUST be maintained in a persistent manner. This table is copied from draft-ietf-adslmib-vdsl2-01.txt, to secure a smooth migration to the VDSL2-LINE MIB when this MIB is approved.
vdsl2ChConfProfileEntry	1.3.6.1.4.1.193.72.300.80.3.1.1		not-accessible	The table vdsl2ChConfProfileTable contains DSL channel profile configuration. A default profile with an index of 'DEFVAL' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document
STR vdsl2ChConfProfProfileName	1.3.6.1.4.1.193.72.300.80.3.1.1.1	SnmpAdminString	not-accessible	This object identifies a row in this table.
U32 vdsl2ChConfProfMinResDataRateDs	1.3.6.1.4.1.193.72.300.80.3.1.1.4	Unsigned32	read-create	Minimum Reserved Data Rate on Downstream direction. The minimum reserved net data rate for the bearer channel, coded in bit/s. This parameter is used only if the Rate Adaptation Mode in the direction of the bearer channel (i.e., Xdsl2LineConfRaModeDs) is set to dynamicRa. This table is from draft-ietf-adslmib-vdsl2-01.txt.
U32 vdsl2ChConfProfMinResDataRateUs	1.3.6.1.4.1.193.72.300.80.3.1.1.5	Unsigned32	read-create	Minimum Reserved Data Rate on Upstream direction. The minimum reserved net data rate for the bearer channel, coded in bit/s. This parameter is used only if the Rate Adaptation Mode in the direction of the bearer channel (i.e., Xdsl2LineConfRaModeUs) is set to dynamicRa. This table is from draft-ietf-adslmib-vdsl2-01.txt.

RFC description

VDSL line performance monitoring and alarm configuration for Ericsson IP-based DSLAMs.

Start monitoring Ericsson Diax IP DSLAM, VDSL/VDSL2 access equipment with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download PEA-VDSL-IPDSLAM

What Is PEA-VDSL-IPDSLAM?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description