PEA-ADSL-IPDSLAM

All MIBs › PEA-ADSL-IPDSLAM

Organization: Ericsson Danmark A/S - Denmark

Last Updated: 2004-05-03

Category: DSL and Broadband

Description: Manages ADSL line configuration, attainable rates, and performance counters on the Ericsson IP DSLAM platform.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is PEA-ADSL-IPDSLAM?

This MIB module is part of Ericsson's proprietary IP DSLAM (Digital Subscriber Line Access Multiplexer) management suite, extending the standard ADSL-LINE-MIB (RFC 2662) with parameters aligned to the ITU-T G.997.1 standard for DSL physical layer management. It exposes line-level data for ADSL modem pairs at both ends of the copper loop — the ATU-C (central office/DSLAM side) and ATU-R (remote/CPE side) — including signal-to-noise margin, output power, and loop attenuation. The MIB is used primarily to monitor hardware-level line quality and performance: administrators track per-port SNR margin, output power history, and bit allocation to detect degrading copper pairs, noise ingress, or failing modem hardware before a line drops. It explicitly builds on and complements the IETF ADSL-LINE-MIB, since that standard MIB predates and does not fully conform to G.997.1. The PEA-ADSL-IPDSLAM MIB is deployed in Ericsson IP DSLAM chassis in carrier and enterprise broadband access networks delivering ADSL service to subscribers.

IPNetwork Monitor allows you to monitor SNMP objects defined in PEA-ADSL-IPDSLAM. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Ericsson IP DSLAM
ADSL access multiplexer

Monitoring Examples

An operator would poll adslAtucPhysXTable and adslAturPhysXTable to compare central-office and customer-premises line statistics side by side, watching adslAtucPhysXPreviousSnrMgn and adslAtucPhysXPreviousOutputPwr for sudden drops indicating crosstalk or a wiring fault. adslAtucPhysXLoopAtn (loop attenuation) rising over time signals a lengthening or degrading copper path, while adslAtucPhysXBitAllocTable shows how bits are distributed across DMT tones, useful for spotting narrowband interference. Persistent SNR margin decline combined with rising loop attenuation on a specific adslAtucPhysXEntry would typically precede a customer-reported ADSL outage.

What Can Be Monitored

SNR margin (ATU-C/ATU-R)
output power
loop attenuation
bit allocation per tone
previous performance history
ADSL line traps

Imported Objects

From ADSL-LINE-EXT-MIB

adslAtucThreshold15MinSesL	OBJECT-TYPE
adslAtucThreshold15MinUasL	OBJECT-TYPE
adslAturThreshold15MinSesL	OBJECT-TYPE
adslAturThreshold15MinUasL	OBJECT-TYPE

From ADSL-LINE-MIB

adslAtucChanCurrTxRate	OBJECT-TYPE
adslAtucChanIntervalNumber	OBJECT-TYPE
adslAtucIntervalNumber	OBJECT-TYPE
adslAtucThresh15MinESs	OBJECT-TYPE
adslAtucThresh15MinLofs	OBJECT-TYPE
adslAtucThresh15MinLols	OBJECT-TYPE
adslAtucThresh15MinLoss	OBJECT-TYPE
adslAturChanCurrTxRate	OBJECT-TYPE
adslAturChanIntervalNumber	OBJECT-TYPE
adslAturIntervalNumber	OBJECT-TYPE
adslAturThresh15MinESs	OBJECT-TYPE
adslAturThresh15MinLofs	OBJECT-TYPE
adslAturThresh15MinLoss	OBJECT-TYPE
adslAturThresh15MinLprs	OBJECT-TYPE
adslLineAlarmConfProfileEntry	OBJECT-TYPE
adslLineConfProfileEntry	OBJECT-TYPE

From DIESEL-SMI

peaIpDslam

OBJECT-IDENTITY

From PEA-BRIDGE-IPDSLAM

lineIndex

OBJECT-TYPE

From PEA-EQUIPMENT-IPDSLAM

errorCode	OBJECT-TYPE
messageId	OBJECT-TYPE

From PEM-STANDARD

eventTime	OBJECT-TYPE
eventTypePem	OBJECT-TYPE
managedObjectClass	OBJECT-TYPE
managedObjectInstance	OBJECT-TYPE
perceivedSeverity	OBJECT-TYPE
probableCause	OBJECT-TYPE
sequenceNumber	OBJECT-TYPE

From RFC1213-MIB

DisplayString

From SNMPv2-CONF

NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Gauge32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

TEXTUAL-CONVENTION
TruthValue

How to Use in IPNetwork Monitor

Example using adslProprietaryPerfDataXFailedInits OID:

Select an Ericsson IP DSLAM, ADSL access multiplexer (ADSL modem-pair line quality) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type adslProprietaryPerfDataXFailedInits into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. It reports the count of failed line initialization attempts since agent reset. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases between polls, since a rising count of errors, failures, or discards often points to a real underlying problem. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
peaAdslIpDslam	1.3.6.1.4.1.193.72.300.10			The IP DSLAM software supports a number of standard and proprietary MIBs. The MIB module defines objects for the management of a pair of ADSL modems at each end of the ADSL line and is an extension to the ADSL-LINE-MIB (RFC2662). The reason for this MIB module is that the original ADSL-LINE- MIB is not conforming to the G.997.1 standard. The draft extension MIB (RFC2662) is not released yet and is also lacking parameters defined in the G.997.1. One naming convention was added to those from the ADSL-LINE-MIB: an 'X' from 'extension' is added to all names.
adslXObjects	1.3.6.1.4.1.193.72.300.10.1
adslAtucPhysXTable	1.3.6.1.4.1.193.72.300.10.1.1		not-accessible	This table provides extra information in relation to the adslAtucPhysTable for ADSL lines.
adslAtucPhysXEntry	1.3.6.1.4.1.193.72.300.10.1.1.1		not-accessible	An entry in adslAtucPhysXTable.
INT adslAtucPhysXPreviousSnrMgn	1.3.6.1.4.1.193.72.300.10.1.1.1.1	INTEGER	read-only	This object contains the previous signal to noise margin for the ATU-C, i.e the total SNR margin recorded when the last synchronisation of the line was carried out.
INT adslAtucPhysXPreviousOutputPwr	1.3.6.1.4.1.193.72.300.10.1.1.1.2	INTEGER	read-only	This object contains the previous measured total output power transmitted by the ATU-C, i.e the total output power recorded when the last synchronisation of the line was carried out.
OCT adslAtucPhysXBitAllocTable	1.3.6.1.4.1.193.72.300.10.1.1.1.3	OCTET STRING	read-only	Upstream bit allocation table. Substituted by adslAtucPhysXBitAllocation in HMI 9.x
OCT adslAtucPhysXSnr	1.3.6.1.4.1.193.72.300.10.1.1.1.4	OCTET STRING	read-only	SNR measured in the upstream band. There are 64 tones in the upstream band and every tone is represented by 4 octets. Substituted by adslAtucPhysXToneSnrUs in HMI 9.x
INT adslAtucPhysXLoopAtn	1.3.6.1.4.1.193.72.300.10.1.1.1.5	INTEGER	read-only	Upstream loop attenuation. Measured difference in the total power transmitted by the peer ATU and the total power received by this ATU.
adslAturPhysXTable	1.3.6.1.4.1.193.72.300.10.1.2		not-accessible	This table provides extra information in relation to the adslAturPhysTable for ADSL lines.
adslAturPhysXEntry	1.3.6.1.4.1.193.72.300.10.1.2.1		not-accessible	An entry in adslAturPhysXTable.
INT adslAturPhysXPreviousSnrMgn	1.3.6.1.4.1.193.72.300.10.1.2.1.2	INTEGER	read-only	This object contains the previous signal to noise margin for the ATU-R, i.e the total SNR margin recorded when the last synchronisation of the line was carried out.
INT adslAturPhysXPreviousOutputPwr	1.3.6.1.4.1.193.72.300.10.1.2.1.3	INTEGER	read-only	This object contains the previous measured total output power transmitted by the ATU-R, i.e the total output power recorded when the last synchronisation of the line was carried out.
OCT adslAturPhysXBitAllocTable	1.3.6.1.4.1.193.72.300.10.1.2.1.4	OCTET STRING	read-only	Downstream bit allocation table, tones 0-255 Substituted by adslAturPhysXBitAllocation in HMI 9.x
OCT adslAturPhysXBitAllocTableExt	1.3.6.1.4.1.193.72.300.10.1.2.1.5	OCTET STRING	read-only	Downstream bit allocation table, tones 256-511 Substituted by adslAturPhysXBitAllocation in HMI 9.x
INT adslAturPhysXLoopAtn	1.3.6.1.4.1.193.72.300.10.1.2.1.6	INTEGER	read-only	Downstream loop attenuation. Measured difference in the total power transmitted by this ATU and the total power received by the peer ATU.
adslLineConfProfileXTable	1.3.6.1.4.1.193.72.300.10.1.3		not-accessible	This table provides extra information in relation to the adslLineConfProfileTable for ADSL line configuration profile.
adslLineConfProfileXEntry	1.3.6.1.4.1.193.72.300.10.1.3.1		not-accessible	Each entry corresponds to an ADSL line configuration profile. Each profile contains a set of ADSL line configuration parameters. The configuration parameters in a profile are applied to those lines referencing that profile.
STR adslConfXName	1.3.6.1.4.1.193.72.300.10.1.3.1.1	SnmpAdminString	read-only	This object is the unique profile name associated with this profile.
STR adslConfXAtucFrequencyBins	1.3.6.1.4.1.193.72.300.10.1.3.1.2	DisplayString	read-write	This object consists of a bitmap of 512 bits, where each bit disables or enables one carrier in the downstream (ATU-C) direction. 1 enables the carrier and 0 disables it. Each bitmap is represented as a list of 64 bytes, each representing a bitmap of 8 bits. The first byte of the list represents carriers 0-7, the second byte represents carriers 8-15, etc. The last byte represents carriers 504-511. In each byte, the LSB represents the lowest carrier in the range, while the MSB represents the highest carrier in the range.
STR adslConfXAturFrequencyBins	1.3.6.1.4.1.193.72.300.10.1.3.1.3	DisplayString	read-write	This object consists of a bitmap of 64 bits, where each bit disables or enables one carrier in the upstream (ATU-R) direction. 1 enables the carrier and 0 disables it. Each bitmap is represented as a list of 8 bytes, each representing a bitmap of 8 bits. The first byte of the list represents carriers 0-7, the second byte represents carriers 8-15, etc. The last byte represents carriers 56-63. In each byte, the LSB represents the lowest carrier in the range, while the MSB represents the highest carrier in the range.
STR adslConfXFrequencyBins	1.3.6.1.4.1.193.72.300.10.1.3.1.4	DisplayString	read-write	This object consists of a bitmap of 256 bits, where each bit disables or enables one carrier. One enables the carrier and zero disables it. The distribution between up- and downstream carriers is autonomously done in the CO-chipset, based upon the selected protocol. Each bitmap is represented as a list of 32 bytes, each representing a bitmap of 8 bits. The first byte of the list represents carriers 0-7, the second byte represents carriers 8-15, etc. The last byte represents carriers 248-255. In each byte, the LSB represents the lowest carrier in the range, while the MSB represents the highest carrier in the range.
INT adslPowerManagementMode	1.3.6.1.4.1.193.72.300.10.1.3.1.5	INTEGER	read-write	Power Management State Enabling (PMMode) as defined in G.997.1 (7.3.1.1.4). Only L2 mode is supported.
INT adslPrmMode	1.3.6.1.4.1.193.72.300.10.1.3.1.6	INTEGER	read-write	Disable or enable protection for a specific PRM frequency
INT adslPrmPower	1.3.6.1.4.1.193.72.300.10.1.3.1.7	INTEGER	read-write	Sets the power level of the PRM signal. Approximation: prmPower ~ 1000 * (Vrms^2). Valid range: 0 to (2E32)-1.
adslLineAlarmConfProfileXTable	1.3.6.1.4.1.193.72.300.10.1.4		not-accessible	This table provides extra information in relation to the adslLineAlarmConfProfileTable for an ADSL alarm configuration profile.
adslLineAlarmConfProfileXEntry	1.3.6.1.4.1.193.72.300.10.1.4.1		not-accessible	Each entry corresponds to an ADSL line alarm configuration profile. Each profile contains a set of ADSL line alarm configuration parameters. The configuration parameters in a profile are applied to those lines referencing that profile.
STR adslAlarmConfXName	1.3.6.1.4.1.193.72.300.10.1.4.1.1	SnmpAdminString	read-only	This object is the unique profile name associated with this profile.
INT adslAlarmConfXAtucThres1DayES	1.3.6.1.4.1.193.72.300.10.1.4.1.2	INTEGER	read-write	The number of Errored Seconds encountered by an ADSL interface within the 24 hour (1 day) data collection period, which causes the SNMP agent to send an adslAtucPerfXESsThresh1DayTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.
INT adslAlarmConfXAturThres1DayES	1.3.6.1.4.1.193.72.300.10.1.4.1.3	INTEGER	read-write	The number of Errored Seconds encountered by an ADSL interface within the 24 hour (1 day) data collection period, which causes the SNMP agent to send an adslAturPerfXESsThresh1DayTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.
INT adslAlarmConfXAtucThres1DaySesL	1.3.6.1.4.1.193.72.300.10.1.4.1.7	INTEGER	read-write	The number of Severely Errored Seconds encountered by an ADSL interface within the 24 hour (1 day) data collection period, which causes the SNMP agent to send an adslAturPerfXSesThresh1DayTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.
INT adslAlarmConfXAturThres1DaySesL	1.3.6.1.4.1.193.72.300.10.1.4.1.8	INTEGER	read-write	The number of Severely Errored Seconds encountered by an ADSL interface within the 24 hour (1 day) data collection period, which causes the SNMP agent to send an adslAturPerfXSesThresh1DayTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.
INT adslAlarmConfXAtucThres1DayUasL	1.3.6.1.4.1.193.72.300.10.1.4.1.9	INTEGER	read-write	The number of Unavailable Seconds encountered by an ADSL interface within the 24 hour (1 day) data collection period, which causes the SNMP agent to send an adslAturPerfXUasThresh1DayTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.
INT adslAlarmConfXAturThres1DayUasL	1.3.6.1.4.1.193.72.300.10.1.4.1.10	INTEGER	read-write	The number of Unavailable Seconds encountered by an ADSL interface within the 24 hour (1 day) data collection period, which causes the SNMP agent to send an adslAturPerfXUasThresh1DayTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.
INT adslAlarmConfXAtucThres1DayLofs	1.3.6.1.4.1.193.72.300.10.1.4.1.15	INTEGER	read-write	The number of Loss of Frame Seconds encountered by an ADSL interface within the 24 hour (1 day) data collection period, which causes the SNMP agent to send an adslAtucPerfXLofsThresh1DayTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.
INT adslAlarmConfXAturThres1DayLofs	1.3.6.1.4.1.193.72.300.10.1.4.1.20	INTEGER	read-write	The number of Loss of Frame Seconds encountered by an ADSL interface within the 24 hour (1 day) data collection period, which causes the SNMP agent to send an adslAturPerfXLofsThresh1DayTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.
INT adslAlarmConfXAtucThres1DayLoss	1.3.6.1.4.1.193.72.300.10.1.4.1.25	INTEGER	read-write	The number of Loss of Signal Seconds encountered by an ADSL interface within the 24 hour (1 day) data collection period, which causes the SNMP agent to send an adslAtucPerfXLossThresh1DayTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.
INT adslAlarmConfXAturThres1DayLoss	1.3.6.1.4.1.193.72.300.10.1.4.1.30	INTEGER	read-write	The number of Loss of Signal Seconds encountered by an ADSL interface within the 24 hour (1 day) data collection period, which causes the SNMP agent to send an adslAturPerfXLossThresh1DayTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.
INT adslAlarmConfXAtucThres1DayLols	1.3.6.1.4.1.193.72.300.10.1.4.1.35	INTEGER	read-write	The number of Loss of Link Seconds encountered by an ADSL interface within the 24 hour (1 day) data collection period, which causes the SNMP agent to send an adslAtucPerfXLolsThresh1DayTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.
INT adslAlarmConfXAturThres1DayLprs	1.3.6.1.4.1.193.72.300.10.1.4.1.40	INTEGER	read-write	The number of Loss of Power Seconds encountered by an ADSL interface within the 24 hour (1 day) data collection period, which causes the SNMP agent to send an adslAturPerfXLprsThresh1DayTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.
adslAtucPerfDataXTable	1.3.6.1.4.1.193.72.300.10.1.6		not-accessible	This table provides extra information in relation to the adslAtucPerfDataTable for each ATU-C.
adslAtucPerfDataXEntry	1.3.6.1.4.1.193.72.300.10.1.6.1		not-accessible	An entry in adslAtucPerfDataXTable.
PER adslAtucPerfXEcs	1.3.6.1.4.1.193.72.300.10.1.6.1.1	PerfCurrentCount	read-only	Count of forward error correction seconds since agent reset.
PER adslAtucPerfXCurr15MinEcs	1.3.6.1.4.1.193.72.300.10.1.6.1.2	PerfCurrentCount	read-only	Count of forward error correction seconds in the current 15 minute interval.
ADS adslAtucPerfXCurr1DayEcs	1.3.6.1.4.1.193.72.300.10.1.6.1.3	AdslPerfCurrDayCount	read-only	Count of the number of forward error correction seconds during the current day as measured by adslAtucPerfCurr1DayTimeElapsed.
ADS adslAtucPerfXPrev1DayEcs	1.3.6.1.4.1.193.72.300.10.1.6.1.4	AdslPerfPrevDayCount	read-only	Count of forward error correction seconds in the interval within the most recent previous 1-day period.
INT adslAtucPerfX1DayValidIntervals	1.3.6.1.4.1.193.72.300.10.1.6.1.10	INTEGER	read-only	The number of previous 1 day intervals in the 1 day interval table for which data was collected. Given that is the maximum # of intervals supported. The value will be unless the measurement was (re-)started within the last days, in which case the value will be the number of complete 1-day intervals for which the agent has at least some data.
INT adslAtucPerfX1DayInvalidIntervals	1.3.6.1.4.1.193.72.300.10.1.6.1.15	INTEGER	read-only	The number of intervals in the range from 0 to the value of adslAtucPerfX1DayValidIntervals for which no data is available.
adslAturPerfDataXTable	1.3.6.1.4.1.193.72.300.10.1.7		not-accessible	This table provides extra information in relation to the adslAturPerfDataTable for each ATU-R.
adslAturPerfDataXEntry	1.3.6.1.4.1.193.72.300.10.1.7.1		not-accessible	An entry in adslAturPerfDataXTable.
PER adslAturPerfXEcs	1.3.6.1.4.1.193.72.300.10.1.7.1.1	PerfCurrentCount	read-only	Count of forward error correction seconds since agent reset.
PER adslAturPerfXCurr15MinEcs	1.3.6.1.4.1.193.72.300.10.1.7.1.2	PerfCurrentCount	read-only	Count of forward error correction seconds in the current 15 minute interval.
ADS adslAturPerfXCurr1DayEcs	1.3.6.1.4.1.193.72.300.10.1.7.1.3	AdslPerfCurrDayCount	read-only	Count of the number of forward error correction seconds during the current day as measured by adslAturPerfCurr1DayTimeElapsed.
ADS adslAturPerfXPrev1DayEcs	1.3.6.1.4.1.193.72.300.10.1.7.1.4	AdslPerfPrevDayCount	read-only	Count of forward error correction seconds in the interval within the most recent previous 1-day period.
INT adslAturPerfX1DayValidIntervals	1.3.6.1.4.1.193.72.300.10.1.7.1.10	INTEGER	read-only	The number of previous 1 day intervals in the 1 day interval table for which data was collected. Given that is the maximum # of intervals supported. The value will be unless the measurement was (re-)started within the last days, in which case the value will be the number of complete 1-day intervals for which the agent has at least some data.
INT adslAturPerfX1DayInvalidIntervals	1.3.6.1.4.1.193.72.300.10.1.7.1.15	INTEGER	read-only	The number of intervals in the range from 0 to the value of adslAturPerfX1DayValidIntervals for which no data is available.
adslAtucIntervalXTable	1.3.6.1.4.1.193.72.300.10.1.8		not-accessible	This table provides extra information in relation to the adslAtucIntervalTable for each ATU-C performance collection interval. Performance Data Interval number 1 is the the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are optional. Interval number 1 is the only interval used currently.
adslAtucIntervalXEntry	1.3.6.1.4.1.193.72.300.10.1.8.1		not-accessible	An entry in the adslAtucIntervalXTable.
NUM adslAtucIntervalXEcs	1.3.6.1.4.1.193.72.300.10.1.8.1.1	PerfIntervalCount	read-only	Count of forward error correction seconds in the interval.
adslAturIntervalXTable	1.3.6.1.4.1.193.72.300.10.1.9		not-accessible	This table provides extra information in relation to the adslAturIntervalTable for each ATU-R performance collection interval. Performance Data Interval number 1 is the the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are optional. Interval number 1 is the only interval used currently.
adslAturIntervalXEntry	1.3.6.1.4.1.193.72.300.10.1.9.1		not-accessible	An entry in the adslAturIntervalXTable.
NUM adslAturIntervalXEcs	1.3.6.1.4.1.193.72.300.10.1.9.1.1	PerfIntervalCount	read-only	Count of forward error correction seconds in the interval.
adslAtucChanPerfDataXTable	1.3.6.1.4.1.193.72.300.10.1.10		not-accessible	This table provides extra ATU-C channel information in relation to the adslAtucChanPerfDataTable. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125).
adslAtucChanPerfDataXEntry	1.3.6.1.4.1.193.72.300.10.1.10.1		not-accessible	An entry in the adslAtucChanPerfDataXTable.
PER adslAtucChanPerfXCurr15MinHecv	1.3.6.1.4.1.193.72.300.10.1.10.1.1	PerfCurrentCount	read-only	Count of all header error correction violations received on this channel within the current 15 minute interval.
PER adslAtucChanPerfXCurr15MinTotalCells	1.3.6.1.4.1.193.72.300.10.1.10.1.2	PerfCurrentCount	read-only	Count of all ATM cells received on this channel within the current 15 minute interval.
PER adslAtucChanPerfXCurr15MinTotalUserCells	1.3.6.1.4.1.193.72.300.10.1.10.1.3	PerfCurrentCount	read-only	Count of all valid non-idle ATM cells successfuly trasmited to the UTOPIA bus within the current 15 minute interval.
PER adslAtucChanPerfXCurr15MinIdleCells	1.3.6.1.4.1.193.72.300.10.1.10.1.4	PerfCurrentCount	read-only	Count of all idle ATM cells received on this channel within the current 15 minute interval.
PER adslAtucChanPerfXCurr15MinIdleCellBitErrors	1.3.6.1.4.1.193.72.300.10.1.10.1.5	PerfCurrentCount	read-only	Count the number of bit errors in the payload of the valid idle ATM cells received on this channel within the current 15 minute interval. An approximate estimate of the BER is given by; idleCellBitErrors/(848idleCells)
ADS adslAtucChanPerfXCurr1DayHecv	1.3.6.1.4.1.193.72.300.10.1.10.1.6	AdslPerfCurrDayCount	read-only	Count of all header error correction violations received on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.
ADS adslAtucChanPerfXCurr1DayTotalCells	1.3.6.1.4.1.193.72.300.10.1.10.1.7	AdslPerfCurrDayCount	read-only	Count of all ATM cells received on this channel during the current day.
ADS adslAtucChanPerfXCurr1DayTotalUserCells	1.3.6.1.4.1.193.72.300.10.1.10.1.8	AdslPerfCurrDayCount	read-only	Count of all valid non-idle ATM cells successfuly trasmited to the UTOPIA bus during the current day.
ADS adslAtucChanPerfXCurr1DayIdleCells	1.3.6.1.4.1.193.72.300.10.1.10.1.9	AdslPerfCurrDayCount	read-only	Count of all idle ATM cells received on this channel during the current day.
ADS adslAtucChanPerfXCurr1DayIdleCellBitErr	1.3.6.1.4.1.193.72.300.10.1.10.1.10	AdslPerfCurrDayCount	read-only	Count the number of bit errors in the payload of the valid idle ATM cells received on this channel during the current day.
ADS adslAtucChanPerfXPrev1DayHecv	1.3.6.1.4.1.193.72.300.10.1.10.1.11	AdslPerfPrevDayCount	read-only	Count of all header error correction violations blocks received on this channel within the most recent previous 1-day period.
ADS adslAtucChanPerfXPrev1DayTotalCells	1.3.6.1.4.1.193.72.300.10.1.10.1.12	AdslPerfPrevDayCount	read-only	Count of all ATM cells received on this channel within the most recent previous 1-day period.
ADS adslAtucChanPerfXPrev1DayTotalUserCells	1.3.6.1.4.1.193.72.300.10.1.10.1.13	AdslPerfPrevDayCount	read-only	Count of all valid non-idle ATM cells successfuly trasmited to the UTOPIA bus within the most recent previous 1-day period.
ADS adslAtucChanPerfXPrev1DayIdleCells	1.3.6.1.4.1.193.72.300.10.1.10.1.14	AdslPerfPrevDayCount	read-only	Count of all idle ATM cells received on this channel within the most recent previous 1-day period.
ADS adslAtucChanPerfXPrev1DayIdleCellBitErr	1.3.6.1.4.1.193.72.300.10.1.10.1.15	AdslPerfPrevDayCount	read-only	Count the number of bit errors in the payload of the valid idle ATM cells received on this channel within the most recent previous 1-day period.
PER adslAtucChanPerfXCurr15MinOverFlowCells	1.3.6.1.4.1.193.72.300.10.1.10.1.16	PerfCurrentCount	read-only	Count the number oc cells discarded due to the received UTOPIA FIFO being full within the current 15 minute interval.
ADS adslAtucChanPerfXCurr1DayOverFlowCells	1.3.6.1.4.1.193.72.300.10.1.10.1.17	AdslPerfCurrDayCount	read-only	Count the number oc cells discarded due to the received UTOPIA FIFO being full during the current day.
PER adslAtucChanPerfXPrev1DayOverFlowCells	1.3.6.1.4.1.193.72.300.10.1.10.1.18	PerfCurrentCount	read-only	Count the number oc cells discarded due to the received UTOPIA FIFO being full within the most recent previous 1-day period.
adslAturChanPerfDataXTable	1.3.6.1.4.1.193.72.300.10.1.11		not-accessible	This table provides extra ATU-R channel information in relation to the adslAturChanPerfDataTable. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125).
adslAturChanPerfDataXEntry	1.3.6.1.4.1.193.72.300.10.1.11.1		not-accessible	An entry in the adslAturChanPerfDataXTable.
PER adslAturChanPerfXCurr15MinHecv	1.3.6.1.4.1.193.72.300.10.1.11.1.1	PerfCurrentCount	read-only	Count of all header error correction violations received on this channel within the current 15 minute interval.
PER adslAturChanPerfXCurr15MinTotalCells	1.3.6.1.4.1.193.72.300.10.1.11.1.2	PerfCurrentCount	read-only	Count of all ATM cells received on this channel within the current 15 minute interval.
PER adslAturChanPerfXCurr15MinTotalUserCells	1.3.6.1.4.1.193.72.300.10.1.11.1.3	PerfCurrentCount	read-only	Count of all valid non-idle ATM cells successfuly received to the UTOPIA bus within the current 15 minute interval.
ADS adslAturChanPerfXCurr1DayHecv	1.3.6.1.4.1.193.72.300.10.1.11.1.4	AdslPerfCurrDayCount	read-only	Count of all header error correction violations received on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed.
ADS adslAturChanPerfXCurr1DayTotalCells	1.3.6.1.4.1.193.72.300.10.1.11.1.5	AdslPerfCurrDayCount	read-only	Count of all ATM cells received on this channel during the current day.
ADS adslAturChanPerfXCurr1DayTotalUserCells	1.3.6.1.4.1.193.72.300.10.1.11.1.6	AdslPerfCurrDayCount	read-only	Count of all valid non-idle ATM cells successfuly received to the UTOPIA bus during the current day.
ADS adslAturChanPerfXPrev1DayHecv	1.3.6.1.4.1.193.72.300.10.1.11.1.7	AdslPerfPrevDayCount	read-only	Count of all header error correction violations received on this channel within the most recent previous 1-day period.
ADS adslAturChanPerfXPrev1DayTotalCells	1.3.6.1.4.1.193.72.300.10.1.11.1.8	AdslPerfPrevDayCount	read-only	Count of all ATM cells received on this channel within the most recent previous 1-day period.
ADS adslAturChanPerfXPrev1DayTotalUserCells	1.3.6.1.4.1.193.72.300.10.1.11.1.9	AdslPerfPrevDayCount	read-only	Count of all valid non-idle ATM cells successfuly received to the UTOPIA bus within the most recent previous 1-day period.
PER adslAturChanPerfXCurr15MinIdleCellBitErrors	1.3.6.1.4.1.193.72.300.10.1.11.1.10	PerfCurrentCount	read-only	Count the number of bit errors in the payload of the valid idle ATM cells received on this channel within the current 15 minute interval. An approximate estimate of the BER is given by; idleCellBitErrors/(848idleCells) Applies to ADSL2 only
ADS adslAturChanPerfXCurr1DayIdleCellBitErr	1.3.6.1.4.1.193.72.300.10.1.11.1.11	AdslPerfCurrDayCount	read-only	Count the number of bit errors in the payload of the valid idle ATM cells received on this channel during the current day. Applies to ADSL2 only.
ADS adslAturChanPerfXPrev1DayIdleCellBitErr	1.3.6.1.4.1.193.72.300.10.1.11.1.12	AdslPerfPrevDayCount	read-only	Count the number of bit errors in the payload of the valid idle ATM cells received on this channel within the most recent previous 1-day period. Applies to ADSL2 only.
adslAtucChanIntervalXTable	1.3.6.1.4.1.193.72.300.10.1.12		not-accessible	This table provides extra information in relation to the adslAtucChanIntervalTable for each ATU-C channel's performance collection interval. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125). Performance Data Interval number 1 is the the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are optional. Interval number 1 is the only interval used currently.
adslAtucChanIntervalXEntry	1.3.6.1.4.1.193.72.300.10.1.12.1		not-accessible	An entry in the adslAtucChanIntervalXTable.
NUM adslAtucChanIntervalXHecv	1.3.6.1.4.1.193.72.300.10.1.12.1.1	PerfIntervalCount	read-only	Count of all header error correction violations received on this channel during this interval.
NUM adslAtucChanIntervalXTotalCells	1.3.6.1.4.1.193.72.300.10.1.12.1.2	PerfIntervalCount	read-only	Count of all ATM cells received on this channel this interval.
NUM adslAtucChanIntervalXTotalUserCells	1.3.6.1.4.1.193.72.300.10.1.12.1.3	PerfIntervalCount	read-only	Count of all valid non-idle ATM cells succesfully transmitted to the UTOPIA bus on this interval.
NUM adslAtucChanIntervalXIdleCells	1.3.6.1.4.1.193.72.300.10.1.12.1.4	PerfIntervalCount	read-only	Count of all idle ATM cells received on this channel this interval.
NUM adslAtucChanIntervalXIdleCellBitErrors	1.3.6.1.4.1.193.72.300.10.1.12.1.5	PerfIntervalCount	read-only	Count the number of bit errors in the payload of the valid idle ATM cells received on this channel on this interval.
NUM adslAtucChanIntervalXOverFlowCells	1.3.6.1.4.1.193.72.300.10.1.12.1.6	PerfIntervalCount	read-only	Count the number oc cells discarded due to the received UTOPIA FIFO being full on this interval.
adslAturChanIntervalXTable	1.3.6.1.4.1.193.72.300.10.1.13		not-accessible	This table provides extra information in relation to the adslAturChanIntervalTable for each ATU-R channel's performance collection interval. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125). Performance Data Interval number 1 is the the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are optional. Interval number 1 is the only interval used currently.
adslAturChanIntervalXEntry	1.3.6.1.4.1.193.72.300.10.1.13.1		not-accessible	An entry in the adslAturChanIntervalXTable.
NUM adslAturChanIntervalXHecv	1.3.6.1.4.1.193.72.300.10.1.13.1.1	PerfIntervalCount	read-only	Count of all header error correction violations received on this channel during this interval.
NUM adslAturChanIntervalXTotalCells	1.3.6.1.4.1.193.72.300.10.1.13.1.2	PerfIntervalCount	read-only	Count of all ATM cells received on this channel this interval.
NUM adslAturChanIntervalXTotalUserCells	1.3.6.1.4.1.193.72.300.10.1.13.1.3	PerfIntervalCount	read-only	Count of all valid non-idle ATM cells succesfully received on the UTOPIA bus on this interval.
NUM adslAturChanIntervalXIdleCellBitErrors	1.3.6.1.4.1.193.72.300.10.1.13.1.4	PerfIntervalCount	read-only	Count the number of bit errors in the payload of the valid idle ATM cells received on this channel on this interval. Applies to ADSL2 only
adslAtucProprietaryPhysXTable	1.3.6.1.4.1.193.72.300.10.1.14		not-accessible	ADSL ATU-C Proprietary Physical Extension Table.
adslAtucProprietaryPhysXEntry	1.3.6.1.4.1.193.72.300.10.1.14.1		not-accessible	An entry in the adslAtucProprietaryPhysXTable.
I32 adslAtucProprietaryPhysXLogS	1.3.6.1.4.1.193.72.300.10.1.14.1.1	Integer32	read-only	Base 2 logarithm for the number of DMT sysmbols per code word in the downstream direction.
INT adslAtucProprietaryPhysXCodingType	1.3.6.1.4.1.193.72.300.10.1.14.1.2	INTEGER	read-only	Coding used in downstream. The following representation is used: 0 - No coding 1 - Trellis coding 2 - ReedSolomon coding 3 - Concatenayed trellis coding and ReedSolomon coding.
BIT adslAtucProprietaryPhysXCurrentFailures	1.3.6.1.4.1.193.72.300.10.1.14.1.3	Bits	read-only	Bit mask giving the set of current active failures on the upstream (bit set => failure is ON). A failure is declared when the corresponding defect is active for more than 2.5 (+/-0.5) sec. A failure is cleared when the corresponding defect is off for at least 10.5 (+/-0.5) sec. The bit index and corresponding failure are: Bit[30] - Set when unavailable time is counted Bit[29] - Set when the modem is not in the Running Showtime state Bit[25] - Loss of cell delineation - interleaved path Bit[24] - Loss of cell delineation - fast path Bit[19] - Loss of signal Bit[18] - Loss of frame Bit[17] - No cell delineation - interleaved Bit[16] - No cell delineation - fast Bit[15] - PTM TC Out-Of-Sync Violation for bearer channel B0 Bit[14] - PTM TC Coding Violation for bearer channel B0, non-preemptive Bit[13] - PTM TC Coding Violation for bearer channel B0, preemptive Bit[12] - PTM TC Out-Of-Sync Violation for bearer channel B1 Bit[11] - PTM TC Coding Violation for bearer channel B1, non-preemptive Bit[10] - PTM TC Coding Violation for bearer channel B1, preemptive Bit[07] - No common mode in Handshake. Set when the test configuration prevents the training in the only mode supported by the ATU-R Bit[06] - Bit rate is too high. Set when the line quality does allow support for the minimum bit rate configured Bit[05] - Communication problem. Sethwne initialisation could not be completed due to time-out or a CRC error in one of the message received from the ATU-R Bit[04] - No detection. Set when the ATU-R has not been detected after 2.5 seconds of attempts to activate the line. Note: The RunningShowtime state is left as soon as unavailable time is counted (10 consecutive severely errored seconds), so bits 1 and 2 are always set together.
BIT adslAtucProprietaryPhysXChangedFailures	1.3.6.1.4.1.193.72.300.10.1.14.1.4	Bits	read-only	Bit mask presenting the upstream failures that have changed (or at least toggled) since last GetLineStatus invocation.
U32 adslAtucProprietaryPhysXActualLineBitRate	1.3.6.1.4.1.193.72.300.10.1.14.1.5	Unsigned32	read-only	Actual line bit rate in the downstream direction.
U32 adslAtucProprietaryPhysXPreviousLineBitRate	1.3.6.1.4.1.193.72.300.10.1.14.1.6	Unsigned32	read-only	Previous line bit rate in the downstream direction.
U32 adslAtucProprietaryPhysXMSGc	1.3.6.1.4.1.193.72.300.10.1.14.1.7	Unsigned32	read-only	Octets in message based portion of the overhead framing structure.
U32 adslAtucProprietaryPhysXMSGlp	1.3.6.1.4.1.193.72.300.10.1.14.1.8	Unsigned32	read-only	ID of the latency path carrying the message based overhead.
INT adslAtucProprietaryRefPsd	1.3.6.1.4.1.193.72.300.10.1.14.1.9	INTEGER	read-only	Upstream refPSD. RefPSD = nominal PSD - power cutback. Maps to the HMI GetLineStatus.linkStatus[US].refPsd.
OCT adslAtucProprietaryPhysXgiNEpart	1.3.6.1.4.1.193.72.300.10.1.14.1.10	OCTET STRING	read-only	The near-end (US) linear scale carrier gain allocation. Granularity: 1/512 relative to the reference gain. Range is [4095..0]. Maps to the HMI GetLineCarrierGains. Substituded by: vdsl2SCStatusGainAlloc Deprecated from: EDA 4.0
OCT adslAtucProprietaryPhysXtssiNEpart	1.3.6.1.4.1.193.72.300.10.1.14.1.11	OCTET STRING	read-only	The US linear TSSI. Granularity: 1/32768 relative to the reference gain. Range is [32768..0]. Maps to the HMI GetLineLinearTssi
OCT adslAtucProprietaryPhysXLastRetrainCause	1.3.6.1.4.1.193.72.300.10.1.14.1.12	OCTET STRING	read-only	Bit[3:0] Identifies the cause of the last initialization failure, according to the G.997.1 recommendation. Possible values are: 1 - Wrong profile (cannot occur in our system) 2 - Configuration not feasible 3 - Communication problem (CRC or time-out error) 4 - No ATU-R detected Bit[7:4] If the last initialization failure is a 'Communication problem', this field identifies the type of communication problem that has occurred. Possible values are: 0 - Timeout during initialization 1 - CRC error during initialization message 2 - Unavailable time declared during Showtime at the near-end 3 - Dynamic Rate Adaptation triggered retrain at the near-end 4 - Unavailable time declared during Showtime at the far-end 5 - Dynamic Rate Adaptation triggered retrain at the far-end 6 - Far-end line counters unavailable. If the last initialization failure is a 'Configuration not feasible' failure, this field indicates whether this applies to the upstream or downstream direction. Possible values are: 0 - Upstream configuration not feasible. 1 - Downstream configuration not feasible. Maps to the HMI GetLineStatus.lastRetrainCause
adslAturProprietaryPhysXTable	1.3.6.1.4.1.193.72.300.10.1.15		not-accessible	ADSL ATU-R Proprietary Physical Extension Table.
adslAturProprietaryPhysXEntry	1.3.6.1.4.1.193.72.300.10.1.15.1		not-accessible	An entry in the adslAturProprietaryPhysXTable.
I32 adslAturProprietaryPhysXLogS	1.3.6.1.4.1.193.72.300.10.1.15.1.1	Integer32	read-only	Base 2 logarithm for the number of DMT symbols per code word in the upstream direction.
INT adslAturProprietaryPhysXCodingType	1.3.6.1.4.1.193.72.300.10.1.15.1.2	INTEGER	read-only	Coding used in upstream. The following representation is used: 0 - No coding 1 - Trellis coding 2 - ReedSolomon coding 3 - Concatenayed trellis coding and ReedSolomon coding.
BIT adslAturProprietaryPhysXCurrentFailures	1.3.6.1.4.1.193.72.300.10.1.15.1.3	Bits	read-only	Bit mask giving the set of current active failures on the downstream (bit set => failure is ON). A failure is declared when the corresponding defect is active for more than 2.5 (+/-0.5) sec. A failure is cleared when the corresponding defect is off for at least 10.5 (+/-0.5) sec. The bit index and corresponding failure are: Bit[30] - Set when unavailable time is counted Bit[29] - Set when the modem is not in the Running Showtime state Bit[25] - Loss of cell delineation - interleaved path Bit[24] - Loss of cell delineation - fast path Bit[19] - Loss of Signal Bit[18] - Loss of Frame Bit[17] - No cell delineation - interleaved Bit[16] - No cell delineation - fast Bit[15] - PTM remote TC Out-Of-Sync violation for bearer B0 Bit[14] - PTM remote TC Out-Of-Sync violation for bearer B1 Bit[13] - Loss of power. Note: the Running Showtime state is left as soon as unavailable time is counted (10 consecutive severely errored seconds), so bits 1 and 2 are always set together.
BIT adslAturProprietaryPhysXChangedFailures	1.3.6.1.4.1.193.72.300.10.1.15.1.4	Bits	read-only	Bit mask presenting the downstream failures that have changed (or at least toggled) since last GetLineStatus invocation.
U32 adslAturProprietaryPhysXActualLineBitRate	1.3.6.1.4.1.193.72.300.10.1.15.1.5	Unsigned32	read-only	Actual line bit rate in the upstream direction.
U32 adslAturProprietaryPhysXPreviousLineBitRate	1.3.6.1.4.1.193.72.300.10.1.15.1.6	Unsigned32	read-only	Previous line bit rate in the upstream direction.
U32 adslAturProprietaryPhysXMSGc	1.3.6.1.4.1.193.72.300.10.1.15.1.7	Unsigned32	read-only	Octets in message based portion of the overhead framing structure.
U32 adslAturProprietaryPhysXMSGlp	1.3.6.1.4.1.193.72.300.10.1.15.1.8	Unsigned32	read-only	ID of the latency path carrying the message based overhead.
INT adslAturProprietaryRefPsd	1.3.6.1.4.1.193.72.300.10.1.15.1.9	INTEGER	read-only	Downstream refPSD. RefPSD = nominal PSD - power cutback. Maps to the HMI GetLineStatus.linkStatus[DS].refPsd.
OCT adslAturProprietaryPhysXgiFELowpart0	1.3.6.1.4.1.193.72.300.10.1.15.1.10	OCTET STRING	read-only	The far-end (DS) linear scale carrier gain allocation. Granularity: 1/512 relative to the reference gain. Range is [4095..0]. Maps to the HMI GetLineCarrierGains. Substituded by: vdsl2SCStatusGainAlloc Deprecated from: EDA 4.0
OCT adslAturProprietaryPhysXgiFEHipart0	1.3.6.1.4.1.193.72.300.10.1.15.1.11	OCTET STRING	read-only	The far-end (DS) linear scale carrier gain allocation. Granularity: 1/512 relative to the reference gain. Range is [4095..0]. Maps to the HMI GetLineCarrierGains. Substituded by: vdsl2SCStatusGainAlloc Deprecated from: EDA 4.0
OCT adslAturProprietaryPhysXgiFELowpart1	1.3.6.1.4.1.193.72.300.10.1.15.1.12	OCTET STRING	read-only	The far-end (DS) linear scale carrier gain allocation. Granularity: 1/512 relative to the reference gain. Range is [4095..0]. Maps to the HMI GetLineCarrierGains. Substituded by: vdsl2SCStatusGainAlloc Deprecated from: EDA 4.0
OCT adslAturProprietaryPhysXgiFEHipart1	1.3.6.1.4.1.193.72.300.10.1.15.1.13	OCTET STRING	read-only	The far-end (DS) linear scale carrier gain allocation. Granularity: 1/512 relative to the reference gain. Range is [4095..0]. Maps to the HMI GetLineCarrierGains. Substituded by: vdsl2SCStatusGainAlloc Deprecated from: EDA 4.0
OCT adslAturProprietaryPhysXgiFELowpart2	1.3.6.1.4.1.193.72.300.10.1.15.1.14	OCTET STRING	read-only	The far-end (DS) linear scale carrier gain allocation. Granularity: 1/512 relative to the reference gain. Range is [4095..0]. Maps to the HMI GetLineCarrierGains. Substituded by: vdsl2SCStatusGainAlloc Deprecated from: EDA 4.0
OCT adslAturProprietaryPhysXgiFEHipart2	1.3.6.1.4.1.193.72.300.10.1.15.1.15	OCTET STRING	read-only	The far-end (DS) linear scale carrier gain allocation. Granularity: 1/512 relative to the reference gain. Range is [4095..0]. Maps to the HMI GetLineCarrierGains. Substituded by: vdsl2SCStatusGainAlloc Deprecated from: EDA 4.0
OCT adslAturProprietaryPhysXgiFELowpart3	1.3.6.1.4.1.193.72.300.10.1.15.1.16	OCTET STRING	read-only	The far-end (DS) linear scale carrier gain allocation. Granularity: 1/512 relative to the reference gain. Range is [4095..0]. Maps to the HMI GetLineCarrierGains. Substituded by: vdsl2SCStatusGainAlloc Deprecated from: EDA 4.0
OCT adslAturProprietaryPhysXgiFEHipart3	1.3.6.1.4.1.193.72.300.10.1.15.1.17	OCTET STRING	read-only	The far-end (DS) linear scale carrier gain allocation. Granularity: 1/512 relative to the reference gain. Range is [4095..0]. Maps to the HMI GetLineCarrierGains. Substituded by: vdsl2SCStatusGainAlloc Deprecated from: EDA 4.0
OCT adslAturProprietaryPhysXtssiFELowpart0	1.3.6.1.4.1.193.72.300.10.1.15.1.18	OCTET STRING	read-only	The far-end (DS) linear scale carrier gain allocation. Granularity: 1/512 relative to the reference gain. Range is [4095..0]. Maps to the HMI GetLineCarrierGains.
OCT adslAturProprietaryPhysXtssiFEHipart0	1.3.6.1.4.1.193.72.300.10.1.15.1.19	OCTET STRING	read-only	The far-end (DS) linear scale carrier gain allocation. Granularity: 1/512 relative to the reference gain. Range is [4095..0]. Maps to the HMI GetLineCarrierGains.
OCT adslAturProprietaryPhysXtssiFELowpart1	1.3.6.1.4.1.193.72.300.10.1.15.1.20	OCTET STRING	read-only	The far-end (DS) linear scale carrier gain allocation. Granularity: 1/512 relative to the reference gain. Range is [4095..0]. Maps to the HMI GetLineCarrierGains.
OCT adslAturProprietaryPhysXtssiFEHipart1	1.3.6.1.4.1.193.72.300.10.1.15.1.21	OCTET STRING	read-only	The far-end (DS) linear scale carrier gain allocation. Granularity: 1/512 relative to the reference gain. Range is [4095..0]. Maps to the HMI GetLineCarrierGains.
OCT adslAturProprietaryPhysXtssiFELowpart2	1.3.6.1.4.1.193.72.300.10.1.15.1.22	OCTET STRING	read-only	The far-end (DS) linear scale carrier gain allocation. Granularity: 1/512 relative to the reference gain. Range is [4095..0]. Maps to the HMI GetLineCarrierGains.
OCT adslAturProprietaryPhysXtssiFEHipart2	1.3.6.1.4.1.193.72.300.10.1.15.1.23	OCTET STRING	read-only	The far-end (DS) linear scale carrier gain allocation. Granularity: 1/512 relative to the reference gain. Range is [4095..0]. Maps to the HMI GetLineCarrierGains.
OCT adslAturProprietaryPhysXtssiFELowpart3	1.3.6.1.4.1.193.72.300.10.1.15.1.24	OCTET STRING	read-only	The far-end (DS) linear scale carrier gain allocation. Granularity: 1/512 relative to the reference gain. Range is [4095..0]. Maps to the HMI GetLineCarrierGains.
OCT adslAturProprietaryPhysXtssiFEHipart3	1.3.6.1.4.1.193.72.300.10.1.15.1.25	OCTET STRING	read-only	The far-end (DS) linear scale carrier gain allocation. Granularity: 1/512 relative to the reference gain. Range is [4095..0]. Maps to the HMI GetLineCarrierGains.
adslAtucProprietaryChanXTable	1.3.6.1.4.1.193.72.300.10.1.16		not-accessible	ADSL ATU-C Proprietary Channel Extension Table.
adslAtucProprietaryChanXEntry	1.3.6.1.4.1.193.72.300.10.1.16.1		not-accessible	An entry in the adslAtucProprietaryChanXEntry.
I32 adslAtucProprietaryChanXB	1.3.6.1.4.1.193.72.300.10.1.16.1.1	Integer32	read-only	Number of bearer channel bytes per data frame allocated to the downstream interleaved/fast buffer, summed over all bearer channels. Will be substituted by adslAtucProprietaryChanXB0B - and B1B
I32 adslAtucProprietaryChanXN	1.3.6.1.4.1.193.72.300.10.1.16.1.2	Integer32	read-only	Number of bytes in an downstream FEC output data frame for the interleaved/fast buffer.
I32 adslAtucProprietaryChanXR	1.3.6.1.4.1.193.72.300.10.1.16.1.3	Integer32	read-only	Number of downstream FEC redundancy bytes per ReedSolomon codeword for the interleaved/fast buffer.
I32 adslAtucProprietaryChanXD	1.3.6.1.4.1.193.72.300.10.1.16.1.4	Integer32	read-only	Downstream interleaved/fast depth.
U32 adslAtucProprietaryChanXSnum	1.3.6.1.4.1.193.72.300.10.1.16.1.5	Unsigned32	read-only	Numerator of the number of PMD symbols over which the FEC data frame spans. Note: This parameter is not supported by VDSL2 protocols.
U32 adslAtucProprietaryChanXSdenom	1.3.6.1.4.1.193.72.300.10.1.16.1.6	Unsigned32	read-only	Denominator of the number of PMD symbols over which the FEC data frame spans. Note: This parameter is not supported by VDSL2 protocols.
U32 adslAtucProprietaryChanXL	1.3.6.1.4.1.193.72.300.10.1.16.1.7	Unsigned32	read-only	Number of bits per symbol.
U32 adslAtucProprietaryChanXM	1.3.6.1.4.1.193.72.300.10.1.16.1.8	Unsigned32	read-only	Number of MUX data frames per FEC data frame (codeword). Note: This parameter applies to ADSL2 or VDSL2 protocols only.
U32 adslAtucProprietaryChanXT	1.3.6.1.4.1.193.72.300.10.1.16.1.9	Unsigned32	read-only	For ADSL2, T is the number of MUX data frames per sync octet. For VDSL2, T is the number of MUX data frames in an overhead subframe.
U32 adslAtucProprietaryChanXB0B	1.3.6.1.4.1.193.72.300.10.1.16.1.10	Unsigned32	read-only	B[0] is the nominal number of bearer octets per MUX data frame from bearer B0. In the case of ADSL2, the actual number of bearer octets per MUX data frame is B[0] + 1 if the MUX frame count is not a multiple of T. In the case of VDSL2, the actual number of bearer octets per MUX data frame varies between B[0] and B[0] + 1 if G/T is not an integer. This param will substitute adslAtucProprietaryChanXB
U32 adslAtucProprietaryChanXB1B	1.3.6.1.4.1.193.72.300.10.1.16.1.11	Unsigned32	read-only	B[1] is the nominal number of bearer octets per MUX data frame from bearer B1. This field is only used for VDSL2, where the actual number of bearer octets per MUX data frame is always B[1], regardless of G/T. This param will substitute adslAtucProprietaryChanXB
U32 adslAtucProprietaryChanActualInpB0	1.3.6.1.4.1.193.72.300.10.1.16.1.15	Unsigned32	read-only	The parameter gives the actual INP for the channel in DS direction. The actual INP is the calculated from the protocol dependant formulas: -VDSL2 protocol: INP = (4RDI)/(NL) -ADSL protocols: INP = (4RD)/L -No showtime: INP = 0
U32 adslAtucProprietaryChanActualInpB1	1.3.6.1.4.1.193.72.300.10.1.16.1.20	Unsigned32	read-only	The parameter gives the actual INP for the channel in DS direction. The actual INP is the calculated from the protocol dependant formulas: -VDSL2 protocol: INP = (4RDI)/(NL) -ADSL protocols: INP = (4RD)/L -No showtime: INP = 0
adslAturProprietaryChanXTable	1.3.6.1.4.1.193.72.300.10.1.17		not-accessible	ADSL ATU-R Proprietary Channel Extension Table.
adslAturProprietaryChanXEntry	1.3.6.1.4.1.193.72.300.10.1.17.1		not-accessible	An entry in the adslAturProprietaryChanXTable.
I32 adslAturProprietaryChanXB	1.3.6.1.4.1.193.72.300.10.1.17.1.1	Integer32	read-only	Number of bearer channel bytes per data frame allocated to the upstream interleaved/fast buffer, summed over all bearer channels. Will be substituted by adslAturProprietaryChanXB0B - and B1B
I32 adslAturProprietaryChanXN	1.3.6.1.4.1.193.72.300.10.1.17.1.2	Integer32	read-only	Number of bytes in an upstream FEC output data frame for the interleaved/fast buffer.
I32 adslAturProprietaryChanXR	1.3.6.1.4.1.193.72.300.10.1.17.1.3	Integer32	read-only	Number of upstream FEC redundancy bytes per ReedSolomon code word for the interleaved/fast buffer.
I32 adslAturProprietaryChanXD	1.3.6.1.4.1.193.72.300.10.1.17.1.4	Integer32	read-only	Upstream interleave/fast depth.
U32 adslAturProprietaryChanXSnum	1.3.6.1.4.1.193.72.300.10.1.17.1.5	Unsigned32	read-only	Numerator of the number of PMD symbols over which the FEC data frame spans. Note: This parameter is not supported by VDSL2 protocols.
U32 adslAturProprietaryChanXSdenom	1.3.6.1.4.1.193.72.300.10.1.17.1.6	Unsigned32	read-only	Denominator of the number of PMD symbols over which the FEC data frame spans. Note: This parameter is not supported by VDSL2 protocols.
U32 adslAturProprietaryChanXL	1.3.6.1.4.1.193.72.300.10.1.17.1.7	Unsigned32	read-only	Number of bits per symbol.
U32 adslAturProprietaryChanXM	1.3.6.1.4.1.193.72.300.10.1.17.1.8	Unsigned32	read-only	Number of MUX data frames per FEC data frame (codeword). Note: This parameter applies to ADSL2 or VDSL2 protocols only.
U32 adslAturProprietaryChanXT	1.3.6.1.4.1.193.72.300.10.1.17.1.9	Unsigned32	read-only	For ADSL2, T is the number of MUX data frames per sync octet. For VDSL2, T is the number of MUX data frames in an overhead subframe.
U32 adslAturProprietaryChanXB0B	1.3.6.1.4.1.193.72.300.10.1.17.1.10	Unsigned32	read-only	B[0] is the nominal number of bearer octets per MUX data frame from bearer B0. In the case of ADSL2, the actual number of bearer octets per MUX data frame is B[0] + 1 if the MUX frame count is not a multiple of T. In the case of VDSL2, the actual number of bearer octets per MUX data frame varies between B[0] and B[0] + 1 if G/T is not an integer. This param will substitute adslAturProprietaryChanXB
U32 adslAturProprietaryChanXB1B	1.3.6.1.4.1.193.72.300.10.1.17.1.11	Unsigned32	read-only	B[1] is the nominal number of bearer octets per MUX data frame from bearer B1. This field is only used for VDSL2, where the actual number of bearer octets per MUX data frame is always B[1], regardless of G/T. This param will substitute adslAturProprietaryChanXB
U32 adslAturProprietaryChanActualInpB0	1.3.6.1.4.1.193.72.300.10.1.17.1.15	Unsigned32	read-only	The parameter gives the actual INP for the channel in US direction. The actual INP is the calculated from the protocol dependant formulas: -VDSL2 protocol: INP = (4RDI)/(NL) -ADSL protocols: INP = (4RD)/L -No showtime: INP = 0
U32 adslAturProprietaryChanActualInpB1	1.3.6.1.4.1.193.72.300.10.1.17.1.20	Unsigned32	read-only	The parameter gives the actual INP for the channel in US direction. The actual INP is the calculated from the protocol dependant formulas: -VDSL2 protocol: INP = (4RDI)/(NL) -ADSL protocols: INP = (4RD)/L -No showtime: INP = 0
adslProprietaryLineConfProfileXTable	1.3.6.1.4.1.193.72.300.10.1.18		not-accessible	ADSL Proprietary Line Configuration Profile Extention Table.
adslProprietaryLineConfProfileXEntry	1.3.6.1.4.1.193.72.300.10.1.18.1		not-accessible	An entry in the adslProprietaryLineConfProfileXTable.
I32 adslAtucProprietaryConfXMaxPower	1.3.6.1.4.1.193.72.300.10.1.18.1.1	Integer32	read-write	Maximum allowed DS transmit power. Unit is 0.1 dBm.
I32 adslAtucProprietaryConfXMaxPsd	1.3.6.1.4.1.193.72.300.10.1.18.1.2	Integer32	read-write	Maximum allowed PSD expressed in dB: unit is 0.1 dB/Hz. The allowed range for the downstream direction is -36 to -52 dBm/Hz. Maps into HMI: MaxTxPsd.
INT adslAtucProprietaryConfXFixedPsd	1.3.6.1.4.1.193.72.300.10.1.18.1.3	INTEGER	read-write	When the flag is set (1), the transmit PSD will be fixed to the minimum of -40dBm/Hz and adslAtucProprietaryConfXMaxPsd. When this flag is not set (0), the modem can break the ADSL initialisation sequence and re-initialise at a more optimal PSD level.
INT adslAtucProprietaryConfXPowerAdaptivity	1.3.6.1.4.1.193.72.300.10.1.18.1.4	INTEGER	read-write	Flag only considered if adslAtucProprietaryConfXFixedPsd is notSet(0). If set, priority goes to power: the modem attempt to achieve the minimum power consumtion as soon as the minimum requested rate is achieved. If not set, priority goes to rate: the modem attempt to achieve the maximum requested bit rate before reducing the transmit power.
INT adslAtucProprietaryConfXOptionsFlagBit1	1.3.6.1.4.1.193.72.300.10.1.18.1.5	INTEGER	read-write	DBM/FBM flag. Possible values are: 0 - Dual Bit Mode (DBM) 1 - FEXT Bitmap Mode (FBM).
INT adslAtucProprietaryConfXOptionsFlagBit2	1.3.6.1.4.1.193.72.300.10.1.18.1.6	INTEGER	read-write	NTR support flag. Annex A and Annex B only. Possible values are: 0 - NTR support enabled 1 - NTR support disabled.
INT adslAtucProprietaryConfXDisableTrellis	1.3.6.1.4.1.193.72.300.10.1.18.1.7	INTEGER	read-write	Set this flag to disable trellis coding capability.
INT adslAtucProprietaryConfXRestartMode	1.3.6.1.4.1.193.72.300.10.1.18.1.8	INTEGER	read-write	Possible states are: 0 - Default behaviour. 1 - When the Running Showtime state is left due to the presence of ten consecutive SES, the modem goes to the Idle Configured state instead of going autonomously to the Running Activation state. 2 - Do not leave Running Showtime state in case of ten consecutive SES. When this option is active, the only way to leave the Running Showtime state is to send the Stop Line message.
INT adslAtucProprietaryConfXMaxFramingMode	1.3.6.1.4.1.193.72.300.10.1.18.1.9	INTEGER	read-write	Possible states are: 0 - default behaviour: suports framing modes one, two and three. 1 - reserved. 2 - reserved. 3 - Maximum framing mode is three: modem will only support framing one, two and three. The parameter is no longer supported in the DSP. Deprecated from: EDA 4.0
INT adslAtucProprietaryConfXDisableBitSwap	1.3.6.1.4.1.193.72.300.10.1.18.1.10	INTEGER	read-write	0 - Enable downstream bitswaps 1 - Disable downstream bitswaps.
INT adslAturProprietaryConfXDisableBitSwap	1.3.6.1.4.1.193.72.300.10.1.18.1.11	INTEGER	read-write	The value of this Mib object is with respect to adslAturProprietaryConfXUsBitSwapBehavior. If the value of adslAturProprietaryConfXUsBitSwapBehavior is classicUpstreamBitswap then it will get/set the US bitswap i.e Bit 0 of disableBitSwap. If the value of adslAturProprietaryConfXUsBitSwapBehavior is fullBandUpstreamBitswap then it will get/set the Full Band US bitswap i.e Bit 2 of disableBitSwap. 0 - Enable upstream bitswaps 1 - Disable upstream bitswaps.
INT adslAtucProprietaryConfXDisableHighBitRateInGLite	1.3.6.1.4.1.193.72.300.10.1.18.1.12	INTEGER	read-write	0 - Enable high bit rates in G.Lite 1 - Limit the upstream bit rate to a maximum of 512 kbps in G.lite. 2 - Limit the downstream bit rate to a maximum of 1.536 Mbps in G.Lite. 3 - Limit upstream and downstream bit rate in G.lite By default, the rate is not limited in G.lite. Maps to the HMI SetlineTestConfiguration.disableHighBitRateInGlite
INT adslAtucProprietaryChanConfXOptimiseImpulseNoiseResilienceIlv	1.3.6.1.4.1.193.72.300.10.1.18.1.13	INTEGER	read-write	Flag: when set to 1 the modem initialisation algorithm gives priority to the impulse noise protection. When set to 0, the modem initialisation algorithm gives priority to reach the maximum bit rate. In this case, the algorithm could initialise with a lower delay than the one specified with the maxDelay parameter.
INT adslAtucProprietaryChanConfXOptimiseImpulseNoiseResilienceFast	1.3.6.1.4.1.193.72.300.10.1.18.1.14	INTEGER	read-write	Flag: when set to 1 the modem initialisation algorithm gives priority to the impulse noise protection. When set to 0, the modem initialisation algorithm gives priority to reach the maximum bit rate. In this case, the algorithm could initialise with a lower delay than the one specified with the maxDelay parameter.
I32 adslAtucProprietaryChanConfXTxAtmFlagsFast	1.3.6.1.4.1.193.72.300.10.1.18.1.15	Integer32	read-write	Configure the behaviour of the downstream ATM processor (value is don't care if the UTOPIA port is not used for bearer). Normally set to zero. This is a bit array controlling the following features Bit[0] - Disable ATM payload scrambling. Bit[1] - Reserved. Set to 0. Bit[2] - Reserved. Set to 0. Bit[3] - Disable HEC regeneration. HEC is passed through transparently instead of being recomputed. Allowed values: 0, 1, 8 and 9.
I32 adslAtucProprietaryChanConfXRxAtmFlagsFast	1.3.6.1.4.1.193.72.300.10.1.18.1.16	Integer32	read-write	Configure the behaviour of the upstream ATM processor (value is don't care if the UTOPIA port is not used for bearer). Normally set to zero. This is a bit mask controlling the following features: Bit[0]- disable descrambler. No ATNM patload descrambling is applied. Bit[1]- Output cells during PRE_SYNC state. The ATM cells with correct HEC will be output the the PRE_SYNC state. Bit[2]- No cells discard on bad HEC. ATM cells with wrong HEC will be sent on the UTOPIA port. Bit[3]- No idle cells discard. Idle cells will be sent on UTOPIA port. Bit[4]- Disable cell delineation. Forces the delineation state to SYNC. Bit[5]- Disable unassigned cell filtering.
I32 adslAtucProprietaryChanConfXTxAtmFlagsIlv	1.3.6.1.4.1.193.72.300.10.1.18.1.17	Integer32	read-write	Configure the behaviour of the downstream ATM processor (value is don't care if the UTOPIA port is not used for bearer). Normally set to zero. This is a bit array controlling the following features Bit[0] - Disable ATM payload scrambling. Bit[1] - Reserved. Set to 0. Bit[2] - Reserved. Set to 0. Bit[3] - Disable HEC regeneration. HEC is passed through transparently instead of being recomputed. Allowed values: 0, 1, 8 and 9.
I32 adslAtucProprietaryChanConfXRxAtmFlagsIlv	1.3.6.1.4.1.193.72.300.10.1.18.1.18	Integer32	read-write	Configure the behaviour of the upstream ATM processor (value is don't care if the UTOPIA port is not used for bearer). Normally set to zero. This is a bit mask controlling the following features: Bit[0]- disable descrambler. No ATNM patload descrambling is applied. Bit[1]- Output cells during PRE_SYNC state. The ATM cells with correct HEC will be output the the PRE_SYNC state. Bit[2]- No cells discard on bad HEC. ATM cells with wrong HEC will be sent on the UTOPIA port. Bit[3]- No idle cells discard. Idle cells will be sent on UTOPIA port. Bit[4]- Disable cell delineation. Forces the delineation state to SYNC. Bit[5]- Disable unassigned cell filtering.
I32 adslAturProprietaryConfXMaxPower	1.3.6.1.4.1.193.72.300.10.1.18.1.19	Integer32	read-write	Maximum allowed US transmit power. Unit is 0.1 dBm.
I32 adslAturProprietaryConfXMaxPsd	1.3.6.1.4.1.193.72.300.10.1.18.1.20	Integer32	read-write	Maximum allowed PSD expressed in dB: unit is 0.1 dB/Hz. This field is not supported in the upstream direction in the current release, and must be set to -380 (-38dBm). Maps into HMI: MaxTxPsd.
INT adslAturProprietaryChanConfXOptimiseImpulseNoiseResilienceIlv	1.3.6.1.4.1.193.72.300.10.1.18.1.21	INTEGER	read-write	Flag: when set to 1 the modem initialisation algorithm gives priority to the impulse noise protection. When set to 0, the modem initialisation algorithm gives priority to reach the maximum bit rate. In this case, the algorithm could initialise with a lower delay than the one specified with the maxDelay parameter.
INT adslAturProprietaryChanConfXOptimiseImpulseNoiseResilienceFast	1.3.6.1.4.1.193.72.300.10.1.18.1.22	INTEGER	read-write	Flag: when set to 1 the modem initialisation algorithm gives priority to the impulse noise protection. When set to 0, the modem initialisation algorithm gives priority to reach the maximum bit rate. In this case, the algorithm could initialise with a lower delay than the one specified with the maxDelay parameter.
I32 adslAtucProprietaryConfXBoostFactor	1.3.6.1.4.1.193.72.300.10.1.18.1.23	Integer32	read-write	Applies an additional upstream power boost. Bits[4:0] - A five bit value X, indicating the boost factor Bits[7:5] - Set to 0x06 to enable, otherwise the boost factor is ignored. The applied upstream mean gi in dB expressed by the boost factor X is: 10log10(1+X/64)
I32 adslAtucProprietaryConfXMaxRxPower	1.3.6.1.4.1.193.72.300.10.1.18.1.24	Integer32	read-write	Maximum receive power at the ATUC. Unit is 0.1 dBm. The ATUC will request an Upstream Power Cutback such that the power received at the CO modem is not higher than MaxRxPower.
I32 adslAtucProprietaryConfXDeltaPsdNormal	1.3.6.1.4.1.193.72.300.10.1.18.1.25	Integer32	read-write	Delta PSD expressed in dBm: unit is 0.1 dBm/Hz. Defines a delta with respect to the protocols maximum nominal PSD value in the downstream direction. The allowed range is -40 to 4 dBm/Hz. Maps into HMI: protocolSpecificLinkConfig[DS].maxTxDeltaPsd[PSD_NORMAL].
I32 adslAtucProprietaryConfXDeltaPsdPlus	1.3.6.1.4.1.193.72.300.10.1.18.1.26	Integer32	read-write	Delta PSD expressed in dBm: unit is 0.1 dBm/Hz. Defines a delta with respect to the protocols maximum nominal PSD value in the downstream direction. The allowed range is -40 to 4 dBm/Hz. Maps into HMI: protocolSpecificLinkConfig[DS].maxTxDeltaPsd[PSD_PLUS].
I32 adslAtucProprietaryConfXDeltaPsdReach	1.3.6.1.4.1.193.72.300.10.1.18.1.27	Integer32	read-write	Delta PSD expressed in dBm: unit is 0.1 dBm/Hz. Defines a delta with respect to the protocols maximum nominal PSD value in the downstream direction. The allowed range is -40 to 4 dBm/Hz. Maps into HMI: protocolSpecificLinkConfig[DS].maxTxDeltaPsd[PSD_REACH].
I32 adslAturProprietaryConfXDeltaPsdNormal	1.3.6.1.4.1.193.72.300.10.1.18.1.28	Integer32	read-write	Delta PSD expressed in dBm: unit is 0.1 dBm/Hz. Defines a delta with respect to the protocols maximum nominal PSD value in the upstream direction. The allowed range is -40 to 4 dBm/Hz. Maps into HMI: protocolSpecificLinkConfig[US].maxTxDeltaPsd[PSD_NORMAL].
I32 adslAturProprietaryConfXDeltaPsdPlus	1.3.6.1.4.1.193.72.300.10.1.18.1.29	Integer32	read-write	Delta PSD expressed in dBm: unit is 0.1 dBm/Hz. Defines a delta with respect to the protocols maximum nominal PSD value in the upstream direction. The allowed range is -40 to 4 dBm/Hz. Maps into HMI: protocolSpecificLinkConfig[US].maxTxDeltaPsd[PSD_PLUS].
I32 adslAturProprietaryConfXDeltaPsdReach	1.3.6.1.4.1.193.72.300.10.1.18.1.30	Integer32	read-write	Delta PSD expressed in dBm: unit is 0.1 dBm/Hz. Defines a delta with respect to the protocols maximum nominal PSD value in the upstream direction. The allowed range is -40 to 4 dBm/Hz. Maps into HMI: protocolSpecificLinkConfig[US].maxTxDeltaPsd[PSD_REACH].
INT adslAtucProprietaryConfXAutomodePIalpha	1.3.6.1.4.1.193.72.300.10.1.18.1.31	INTEGER	read-write	Automode performance index alpha. The allowed range is 1 to 255. Maps into HMI: PhysicalLayerConfig.automodePIalpha.
INT adslAtucProprietaryConfXAutomodePIbeta	1.3.6.1.4.1.193.72.300.10.1.18.1.32	INTEGER	read-write	Automode performance index beta. The allowed range is 1 to 255. Maps into HMI: PhysicalLayerConfig.automodePIbeta.
INT adslAtucProprietaryConfXOptionsFlagBit4	1.3.6.1.4.1.193.72.300.10.1.18.1.33	INTEGER	read-write	Diagnostic mode (ADSL2 only). Possible values are: 0 - Diagnostic mode disabled 1 - Diagnostic mode enabled. Maps into HMI: PhysicalLayerConfig.optionFlags Bit[4].
INT adslAtucProprietaryConfXAdslPlusTxFilterId	1.3.6.1.4.1.193.72.300.10.1.18.1.34	INTEGER	read-write	Additional Tx filter setting for G.992.5 (ADSL2+). The allowed range is 0 to 15. Maps into HMI: PhysicalLayerConfig.adslPlusTxFilterId.
INT adslAtucProprietaryConfXDisableUS1bitConst	1.3.6.1.4.1.193.72.300.10.1.18.1.35	INTEGER	read-write	0 - Enable upstream 1 bit constellation 1 - Disable upstream 1 bit constellation. Maps into HMI: TestConfigMessage.disableUS1bitConst.
INT adslAtucProprietaryConfXDisableWindowing	1.3.6.1.4.1.193.72.300.10.1.18.1.36	INTEGER	read-write	0 - Enable the transmit windowing 1 - Disable the transmit windowing. Maps into HMI: TestConfigMessage.disableWindowing.
INT adslAtucProprietaryConfXDisableShowtimeExit	1.3.6.1.4.1.193.72.300.10.1.18.1.37	INTEGER	read-write	0 - Enable exit from showtime if CPE doesn't reply to GetCounter overhead message 1 - Disable exit from showtime if CPE doesn't reply to GetCounter overhead message. Maps into HMI: TestConfigMessage.disableShowtimeExit.
INT adslAtucProprietaryConfXDisableNitro	1.3.6.1.4.1.193.72.300.10.1.18.1.38	INTEGER	read-write	0 - Enable BCM Nitro feature 1 - Disable BCM Nitro feature. Maps into HMI: TestConfigMessage.disableNitro.
INT adslAtucProprietaryConfXDisableUpdateTestParameters	1.3.6.1.4.1.193.72.300.10.1.18.1.39	INTEGER	read-write	0 - Enable automatic test parameters update 1 - Disable automatic test parameters update. Maps into HMI: TestConfigMessage.disableUpdateTestParameters.
INT adslAtucProprietaryConfXTssiShapeNrOfBreakPoints	1.3.6.1.4.1.193.72.300.10.1.18.1.40	INTEGER	read-write	Configuration of custom TssiShape in showtime. Number of breakpoints (0 - disables custom TssiShape). Maps into HMI: PhysicalLayerConfig.customTssiShape. Must be configured while adsl_ifAdminStatus is down
OCT adslAtucProprietaryConfXTssiShapeAdsl2ProtocolType	1.3.6.1.4.1.193.72.300.10.1.18.1.41	OCTET STRING	read-write	Configuration of custom TssiShape in showtime. ADSL2 protocol (0 - disables custom TssiShape). bit_0: G.992.3 Annex A/B/J bit_1: G.992.5 Annex A/B/M bit_2: G.992.3 Annex L Maps into HMI: PhysicalLayerConfig.customTssiShape. Must be configured while adsl_ifAdminStatus is down
OCT adslAtucProprietaryConfXTssiShapeBreakPoint	1.3.6.1.4.1.193.72.300.10.1.18.1.42	OCTET STRING	read-write	Configuration of custom TssiShape for showtime. Defines 16 break points which maps into HMI: PhysicalLayerConfig.customTssiShape[0-15]. The bitmap for each breakpoint: bit_0-6: log Tssi in 0.5 db, [0,-62] bit_7-15: ToneIndex, [0,511] Must be configured while adsl_ifAdminStatus is down
INT adslAtucProprietaryChanConfXINPminIlvB0	1.3.6.1.4.1.193.72.300.10.1.18.1.43	INTEGER	read-write	Impulse Noise Protection in number of DMT symbols according to G.992.3. Possible values are: 0 -> No protection 1 -> 1/2 DMT symbol protection 2 -> 1 DMT symbol protection 3 -> 2 DMT symbol protection 4 -> 4 DMT symbol protection 5 -> 8 DMT symbol protection 6 -> 16 DMT symbol protection Note that the INP value must match the configured maximum delay to form a feasible profile
INT adslAtucProprietaryChanConfXINPminFastB0	1.3.6.1.4.1.193.72.300.10.1.18.1.44	INTEGER	read-write	Impulse Noise Protection in number of DMT symbols according to G.992.3. Possible values are: 0 -> No protection 1 -> 1/2 DMT symbol protection 2 -> 1 DMT symbol protection 3 -> 2 DMT symbol protection 4 -> 4 DMT symbol protection 5 -> 8 DMT symbol protection 6 -> 16 DMT symbol protection Note that the INP value must match the configured maximum delay to form a feasible profile
INT adslAtucProprietaryChanConfXINPminFastB1	1.3.6.1.4.1.193.72.300.10.1.18.1.45	INTEGER	read-write	Impulse Noise Protection in number of DMT symbols according to G.992.3. Possible values are: 0 -> No protection 1 -> 1/2 DMT symbol protection 2 -> 1 DMT symbol protection 3 -> 2 DMT symbol protection 4 -> 4 DMT symbol protection 5 -> 8 DMT symbol protection 6 -> 16 DMT symbol protection Note that the INP value must match the configured maximum delay to form a feasible profile
INT adslAturProprietaryChanConfXINPminIlvB0	1.3.6.1.4.1.193.72.300.10.1.18.1.46	INTEGER	read-write	Impulse Noise Protection in number of DMT symbols according to G.992.3. Possible values are: 0 -> No protection 1 -> 1/2 DMT symbol protection 2 -> 1 DMT symbol protection 3 -> 2 DMT symbol protection 4 -> 4 DMT symbol protection 5 -> 8 DMT symbol protection 6 -> 16 DMT symbol protection Note that the INP value must match the configured maximum delay to form a feasible profile
INT adslAturProprietaryChanConfXINPminFastB0	1.3.6.1.4.1.193.72.300.10.1.18.1.47	INTEGER	read-write	Impulse Noise Protection in number of DMT symbols according to G.992.3. Possible values are: 0 -> No protection 1 -> 1/2 DMT symbol protection 2 -> 1 DMT symbol protection 3 -> 2 DMT symbol protection 4 -> 4 DMT symbol protection 5 -> 8 DMT symbol protection 6 -> 16 DMT symbol protection Note that the INP value must match the configured maximum delay to form a feasible profile
INT adslAturProprietaryChanConfXINPminFastB1	1.3.6.1.4.1.193.72.300.10.1.18.1.48	INTEGER	read-write	Impulse Noise Protection in number of DMT symbols according to G.992.3. Possible values are: 0 -> No protection 1 -> 1/2 DMT symbol protection 2 -> 1 DMT symbol protection 3 -> 2 DMT symbol protection 4 -> 4 DMT symbol protection 5 -> 8 DMT symbol protection 6 -> 16 DMT symbol protection Note that the INP value must match the configured maximum delay to form a feasible profile
INT adslAtucProprietaryConfXOptionsFlagBit5	1.3.6.1.4.1.193.72.300.10.1.18.1.49	INTEGER	read-write	Custom PSD mask with extra Tx LPF. By enabling this feature an extra Tx LPF with a cutoff frequency at 950kHz and >27 dB attenuation above 1.5 MHz is inserted. Made deprecated. Use the adslEnableACIF instead. Valid from: EDA 1.3 Rxx Deprecated from: EDA 2.0 SP1 Possible values are: 0 - Extra TX LPF disabled 1 - Extra TX LPF enabled. Maps into HMI: PhysicalLayerConfig.optionFlags Bit[5].
INT adslAtucProprietaryConfXDisableShalfOptionBit0	1.3.6.1.4.1.193.72.300.10.1.18.1.50	INTEGER	read-write	Possible values are: 0 - enable S = 1/2 in ADSL1 1 - disable S = 1/2 in ADSL1 Maps into HMI: TestConfigMessage.disableShalfOption Bit[0]. Note that use of this option bit is restricted in EDA due to the impact on selected latency mode.
INT adslAtucProprietaryConfXDisableShalfOptionBit1	1.3.6.1.4.1.193.72.300.10.1.18.1.51	INTEGER	read-write	Possible values are: 0 - accept all CPE's 1 - ignore certain CPE reporting S = 1/2 support in R-MSG1. Maps into HMI: TestConfigMessage.disableShalfOption Bit[1]. Note that use of this option bit is restricted in EDA due to the impact on selected latency mode.
INT adslAtucProprietaryConfXDisableLargeD	1.3.6.1.4.1.193.72.300.10.1.18.1.52	INTEGER	read-write	Disables possible selection of a DS interleaving depth (D) greater than 64. 0 - normal operation 1 - disable DS interleave depth > 64 Note: This parameter is used for ADSL protocols only.
INT adslAtucProprietaryConfXForceSegmentation	1.3.6.1.4.1.193.72.300.10.1.18.1.53	INTEGER	read-write	0 - normal operation 1 - force segmentation of overhead msgs > 10 bytes Maps into HMI: TestConfigMessage.forceSegmentation.
INT adslAtucProprietaryConfXRelaxInpMinCheck	1.3.6.1.4.1.193.72.300.10.1.18.1.54	INTEGER	read-write	0 - strictly obay the config INP 1 - accept INPminDS=3 even if (config) INPmin > 3 Maps into HMI: TestConfigMessage.relaxInpMinCheck.
INT adslAtucProprietaryConfXhsTxPSD0	1.3.6.1.4.1.193.72.300.10.1.18.1.55	INTEGER	read-write	-128 is a special value indicating that this carrier set shall not be transmitted. Maps into HMI: PhysicalLayerConfig.hsTxPSD[0].
INT adslAtucProprietaryConfXhsTxPSD1	1.3.6.1.4.1.193.72.300.10.1.18.1.56	INTEGER	read-write	-128 is a special value indicating that this carrier set shall not be transmitted. Maps into HMI: PhysicalLayerConfig.hsTxPSD[1].
INT adslAtucProprietaryConfXhsTxPSD2	1.3.6.1.4.1.193.72.300.10.1.18.1.57	INTEGER	read-write	-128 is a special value indicating that this carrier set shall not be transmitted. Maps into HMI: PhysicalLayerConfig.hsTxPSD[2].
INT adslAtucProprietaryChanMinL2BitRateB0	1.3.6.1.4.1.193.72.300.10.1.18.1.58	INTEGER	read-write	The threshold for L2 entry. If the mean rate is below MinL2BitRate for L2LowRateSlots the L2 mode is entered (CO side initiated L2 entry). Valid range is [0..minBitRateDS] Maps into HMI: SetLineTrafficConfig.minL2BitRate.
INT adslAtucProprietaryChanMinL2BitRateB1	1.3.6.1.4.1.193.72.300.10.1.18.1.59	INTEGER	read-write	The threshold for L2 entry. If the mean rate is below MinL2BitRate for L2LowRateSlots the L2 mode is entered (CO side initiated L2 entry). Valid range is [0..minBitRateDS] Maps into HMI: SetLineTrafficConfig.minL2BitRate.
INT adslAtucProprietaryChanL2LowRateSlotsB0	1.3.6.1.4.1.193.72.300.10.1.18.1.60	INTEGER	read-write	The time interval for L2 entry. If the mean rate is below MinL2BitRate for L2LowRateSlots the L2 mode is entered (CO side initiated L2 entry). Valid range is [0..65535] Value 0 disables automatic power management. Maps into HMI: SetLineTrafficConfig.L2LowRateSlots.
INT adslAtucProprietaryChanL2LowRateSlotsB1	1.3.6.1.4.1.193.72.300.10.1.18.1.61	INTEGER	read-write	The time interval for L2 entry. If the mean rate is below MinL2BitRate for L2LowRateSlots the L2 mode is entered (CO side initiated L2 entry). Valid range is [0..65535] Value 0 disables automatic power management. Maps into HMI: SetLineTrafficConfig.L2LowRateSlots.
INT adslAtucProprietaryChanL2PacketB0	1.3.6.1.4.1.193.72.300.10.1.18.1.62	INTEGER	read-write	The UTOPIA output buffer threshold that triggers L0 entry (CO side initiated L0 entry). Valid range is [0..28] Maps into HMI: SetLineTrafficConfig.L2Packet.
INT adslAtucProprietaryChanL2PacketB1	1.3.6.1.4.1.193.72.300.10.1.18.1.63	INTEGER	read-write	The UTOPIA output buffer threshold that triggers L0 entry (CO side initiated L0 entry). Valid range is [0..28] Maps into HMI: SetLineTrafficConfig.L2Packet.
INT adslAtucProprietaryChanMaxL2BitRateB0	1.3.6.1.4.1.193.72.300.10.1.18.1.64	INTEGER	read-write	The threshold value for initiating L0 entry. (CPE side initiated L0 entry). Valid range is [minL2BitRate..maxBitRateDS] Maps into HMI: SetLineTrafficConfig.minL2BitRate.
INT adslAtucProprietaryChanMaxL2BitRateB1	1.3.6.1.4.1.193.72.300.10.1.18.1.65	INTEGER	read-write	The value used for initiating L0 entry. (CPE side initiated L0 entry). Valid range is [minL2BitRate..maxBitRateDS] Maps into HMI: SetLineTrafficConfig.maxL2BitRate.
INT adslAtucProprietaryL2TestConfigBit0	1.3.6.1.4.1.193.72.300.10.1.18.1.66	INTEGER	read-write	L2TestConfig bit mask: Bit[0]: Disable autonomous L2 entry/exit. Bit[1]: Disable autonomous L2 power trim. Bit[2]: Overrule L2 min/max rate calculation. Maps into HMI: SetLineTestConfig.L2TestConfig.
INT adslAtucProprietaryL2TestConfigBit1	1.3.6.1.4.1.193.72.300.10.1.18.1.67	INTEGER	read-write	L2TestConfig bit mask: Bit[0]: Disable autonomous L2 entry/exit. Bit[1]: Disable autonomous L2 power trim. Bit[2]: Overrule L2 min/max rate calculation. Maps into HMI: SetLineTestConfig.L2TestConfig.
INT adslAtucProprietaryL2TestConfigBit2	1.3.6.1.4.1.193.72.300.10.1.18.1.68	INTEGER	read-write	L2TestConfig bit mask: Bit[0]: Disable autonomous L2 entry/exit. Bit[1]: Disable autonomous L2 power trim. Bit[2]: Overrule L2 min/max rate calculation. Maps into HMI: SetLineTestConfig.L2TestConfig.
INT adslAtucProprietaryL2MinAtpr	1.3.6.1.4.1.193.72.300.10.1.18.1.69	INTEGER	read-write	Minimum power reduction at L2 entry. Valid range is [0..15] Maps into HMI: SetLineTrafficConfig.L2MinAtpr.
INT adslAtucProprietaryL0Time	1.3.6.1.4.1.193.72.300.10.1.18.1.70	INTEGER	read-write	Minimum time in L0 before L2 entry. Valid range is [0..65535] Maps into HMI: SetLinePhysicalConfig.L0Time.
INT adslAtucProprietaryL2Time	1.3.6.1.4.1.193.72.300.10.1.18.1.71	INTEGER	read-write	Minimum time in L2 before L0 entry. Valid range is [0..65535] Maps into HMI: SetLinePhysicalConfig.L2Time.
INT adslAtucProprietaryL2Atpr	1.3.6.1.4.1.193.72.300.10.1.18.1.72	INTEGER	read-write	Maximum aggregate transmit power reduction per L2 trim. Valid range is [0..31] Maps into HMI: SetLinePhysicalConfig.L2Atpr.
INT adslAtucProprietaryL2Atprt	1.3.6.1.4.1.193.72.300.10.1.18.1.73	INTEGER	read-write	Maximum total aggregate transmit power reduction in L2 trim mode. Valid range is [0..31] Maps into HMI: SetLinePhysicalConfig.L2Atprt.
INT adslAtucProprietaryRateAdaptationFlagsBit0Upstream	1.3.6.1.4.1.193.72.300.10.1.18.1.74	INTEGER	read-write	Possible values are: 0 - enable minimum SNR margin functionality 1 - disable minimum SNR margin functionality Maps into HMI: SetLinePhysicalConfig.linkconfig[US].rateAdaptationFlags.
INT adslAtucProprietaryRateAdaptationFlagsBit0Downstream	1.3.6.1.4.1.193.72.300.10.1.18.1.75	INTEGER	read-write	Possible values are: 0 - enable minimum SNR margin functionality 1 - disable minimum SNR margin functionality Maps into HMI: SetLinePhysicalConfig.linkconfig[DS].rateAdaptationFlags.
INT adslAtucValidRateExtension	1.3.6.1.4.1.193.72.300.10.1.18.1.76	INTEGER	read-write	Some ADSL2(+) CPE's do not strictly comply to the rate constrains negotiated during G.hs. To avoid initialization failure with those CPE's the rate check can be relaxed by a configurable value, allowing to extend the allowed rate interval
INT adslAtucProprietaryConfXMsgMinDS	1.3.6.1.4.1.193.72.300.10.1.18.1.77	INTEGER	read-write	This is minimum framing overhead for down stream.Allowed range is 4 to 28 inclusive of them.
INT adslAtucProprietaryConfXMsgMinUS	1.3.6.1.4.1.193.72.300.10.1.18.1.78	INTEGER	read-write	This is minimum framing overhead for up stream.Allowed range is 4 to 28 inclusive of them.
INT adslAturProprietaryConfXUsBitSwapBehavior	1.3.6.1.4.1.193.72.300.10.1.18.1.79	INTEGER	read-write	The adslAturProprietaryConfXUsBitSwapBehavior has effect only if the upstream bitswap is enabled in adslAturProprietaryConfXDisableBitSwap. The adslAturProprietaryConfXUsBitSwapBehavior controls the behaviour of the upstream bitswap: 0 - Classic upstream bitswaps 1 - FullBand upstream bitswaps.
INT adslAtucProprietaryConfXStrictPerCheck	1.3.6.1.4.1.193.72.300.10.1.18.1.80	INTEGER	read-write	When enabled, limit SRA such as to respect the 15 to 20ms PER constraint. Default disabled.
INT adslAtucProprietaryConfXTpsTcType	1.3.6.1.4.1.193.72.300.10.1.18.1.85	INTEGER	read-write	Configure allowed traffic type: ATM, PTM or both. Valid from: EDA 2.2 MA2 Obsoleted from: EDA 4.0 Replaced by vdslVtucProprietaryConfXTpsTcType in PEA-VDSL-IPDSLAM
INT adslAtucProprietaryConfXPsdOptimConfig	1.3.6.1.4.1.193.72.300.10.1.18.1.90	INTEGER	read-write	This parameter controls the selected PSD optimization modes: 0: No optimization. A fixed TSSI shape (either the default of the configured shape) is used. 1: PSD optimization. The TSSI shape that optimally fills the configured PSD mask is computed dynamically. 2: PSD shaping. The TSSI shape the provides optimal downstream performance within the PSD mask constraints is computed dynamically. Note: Applies to ADSL-only applications.
U32 adslAtucProprietaryConfXPsdMaskSelectUs	1.3.6.1.4.1.193.72.300.10.1.18.1.95	Unsigned32	read-write	The selected upstream PSD mask. This parameter is used only for annexes J and M of G.992.3 and G.992.5, and the same selection is used for all relevant enabled bits in xdsl2LConfProfAtuTransSysEna. Value Annex J Annex M 1 ADLU-32 EU-32 2 ADLU-36 EU-36 3 ADLU-40 EU-40 4 ADLU-44 EU-44 5 ADLU-48 EU-48 6 ADLU-52 EU-52 7 ADLU-56 EU-56 8 ADLU-60 EU-60 9 ADLU-64 EU-64 Applies only to lines running G.992.3 or G.992.5 This parameter is copied from draft-ietf-adslmib-vdsl2-01.txt, to secure a smooth migration to the VDSL2-LINE MIB when this MIB is approved.
T/F adslAtucProprietaryConfXDisableProtocolFallback	1.3.6.1.4.1.193.72.300.10.1.18.1.100	TruthValue	read-write	This parameter controls the protocol fallback mechanism. If set it disables protocol fallback mechanism. Note: Applies to ADSL-only applications.
adslLineXTable	1.3.6.1.4.1.193.72.300.10.1.19		not-accessible	This table is a proprietary extension of RFC2662. It contains ADSL line configuration and monitoring information. This includes the ATU-(R/C) capabilities and actual ADSL transmission system.
adslLineXEntry	1.3.6.1.4.1.193.72.300.10.1.19.1		not-accessible	An entry extends the adslLineEntry defined in [RFC2662]. Each entry corresponds to an ADSL line.
BIT adslLineXTransAtucCap	1.3.6.1.4.1.193.72.300.10.1.19.1.1	Bits	read-only	The transmission modes, represented by a bitmask that the ATU-C is capable of supporting. The modes available are limited by the design of the equipment.
BIT adslLineXTransAtucConfig	1.3.6.1.4.1.193.72.300.10.1.19.1.2	Bits	read-write	The transmission modes, represented by a bitmask, currently enabled by the ATU-C. The manager can only set those modes that are supported by the ATU-C. An ATU-C's supported modes are provided by adslLineXTransAtucCap. Setting a bit in the mask enables the protocol in question.
BIT adslLineXTransAtucActual	1.3.6.1.4.1.193.72.300.10.1.19.1.3	Bits	read-only	The actual transmission mode of the ATU-C. During ADSL line initialization, the ADSL Transceiver Unit - Remote terminal end (ATU-R) will determine the mode used for the link. This value will be limited a single transmission mode that is a subset of those modes enabled by the ATU-C and denoted by adslLineXTransAtucConfig. After an initialization has occurred, its mode is saved as the 'Current' mode and is persistence should the link go down.
BIT adslLineXTransAturCap	1.3.6.1.4.1.193.72.300.10.1.19.1.4	Bits	read-only	The transmission modes, represented by a bitmask that the ATU-R is capable of supporting. The modes available are limited by the design of the equipment.
adslProprietaryPerfDataXTable	1.3.6.1.4.1.193.72.300.10.1.20		not-accessible	ADSL Proprietary Performance Data Extension Table.
adslProprietaryPerfDataXEntry	1.3.6.1.4.1.193.72.300.10.1.20.1		not-accessible	An entry in adslProprietaryPerfDataXTable.
INT adslProprietaryPerfDataXReset	1.3.6.1.4.1.193.72.300.10.1.20.1.1	INTEGER	read-write	When set to 'reset' the ADSL line performance total counters are reset to 0.
U32 adslProprietaryPerfDataXSinceResetTimeElapsed	1.3.6.1.4.1.193.72.300.10.1.20.1.2	Unsigned32	read-only	Elapsed time in seconds since the last reset of the ADSL line performance total counters.
C32 adslProprietaryPerfDataXFailedInitsEx	1.3.6.1.4.1.193.72.300.10.1.20.1.3	Counter32	read-only	Count of failed line initialization attempts since agent reset.
adslAtucLineQualityThresholdTable	1.3.6.1.4.1.193.72.300.10.1.21		not-accessible	This table contains the downstream line quality alarm thresholds. Thresholds can be configured on a per channel basis
adslAtucLineQualityThresholdEntry	1.3.6.1.4.1.193.72.300.10.1.21.1		not-accessible	An entry in adslAtucLineQualityThresholdTable
U32 adslAtucLineQualityThresChan0	1.3.6.1.4.1.193.72.300.10.1.21.1.1	Unsigned32	read-write	Line quality alarm threshold for channel 0
U32 adslAtucLineQualityThresChan1	1.3.6.1.4.1.193.72.300.10.1.21.1.2	Unsigned32	read-write	Line quality alarm threshold for channel 1
adslAturLineQualityThresholdTable	1.3.6.1.4.1.193.72.300.10.1.22		not-accessible	This table contains the upstream line quality alarm thresholds. Thresholds can be configured on a per channel basis
adslAturLineQualityThresholdEntry	1.3.6.1.4.1.193.72.300.10.1.22.1		not-accessible	An entry in adslAturLineQualityThresholdTable
U32 adslAturLineQualityThresChan0	1.3.6.1.4.1.193.72.300.10.1.22.1.1	Unsigned32	read-write	Line quality alarm threshold for channel 0
U32 adslAturLineQualityThresChan1	1.3.6.1.4.1.193.72.300.10.1.22.1.2	Unsigned32	read-write	Line quality alarm threshold for channel 1
adslLineBondingConfTable	1.3.6.1.4.1.193.72.300.10.1.23		not-accessible	This table contains the Line Bonding configuration.
adslLineBondingConfEntry	1.3.6.1.4.1.193.72.300.10.1.23.1		not-accessible	An entry in adslLineBondingConfTable
INT adslLineBondGroupAdminStatus	1.3.6.1.4.1.193.72.300.10.1.23.1.1	INTEGER	read-write	The desired state of the bonding group.
BIT adslLineBondGroupMembers	1.3.6.1.4.1.193.72.300.10.1.23.1.2	Bits	read-write	Indicates which lines should be bonded in in this bonding group. Include main line and ordinary member lines. Note that the Channel 1 is not yet supported in IP DSLAM.
U32 adslLineBondDsGroupRateMin	1.3.6.1.4.1.193.72.300.10.1.23.1.3	Unsigned32	read-write	The configured minimum DS group rate.
U32 adslLineBondDsGroupRateMax	1.3.6.1.4.1.193.72.300.10.1.23.1.4	Unsigned32	read-write	The configured maximum DS group rate.
U32 adslLineBondUsGroupRateMin	1.3.6.1.4.1.193.72.300.10.1.23.1.5	Unsigned32	read-write	The configured minimum US group rate.
U32 adslLineBondUsGroupRateMax	1.3.6.1.4.1.193.72.300.10.1.23.1.6	Unsigned32	read-write	The configured maximum US group rate.
U32 adslAtucLineBondLineQualityThres	1.3.6.1.4.1.193.72.300.10.1.23.1.7	Unsigned32	read-write	Line quality alarm threshold for the bonding group.
U32 adslAturLineBondLineQualityThres	1.3.6.1.4.1.193.72.300.10.1.23.1.8	Unsigned32	read-write	Line quality alarm threshold for the bonding group.
T/F adslAturLineBondLineNoWaitAllBondingLines	1.3.6.1.4.1.193.72.300.10.1.23.1.10	TruthValue	read-write	This parameter controls bonding mode behaviour. If set, this allows the bonding group to be active as soon as at least one line is in Showtime. Note: This is a non-standardbehavior..
adslLineBondingStatusTable	1.3.6.1.4.1.193.72.300.10.1.24		not-accessible	This table contains the stautus information of this bonding group.
adslLineBondingStatusEntry	1.3.6.1.4.1.193.72.300.10.1.24.1		not-accessible	An entry in adslLineBondingStatusTable.
INT adslLineBondGroupOperStatus	1.3.6.1.4.1.193.72.300.10.1.24.1.1	INTEGER	read-write	The operational state of the bonding group. When operational state is down, no data traffic can be passed.
U32 adslLineBondGroupActualRateDs	1.3.6.1.4.1.193.72.300.10.1.24.1.2	Unsigned32	read-write	The actual DS rate for the bonding group.
U32 adslLineBondGroupActualRateUs	1.3.6.1.4.1.193.72.300.10.1.24.1.3	Unsigned32	read-write	The actual US rate for the bonding group.
OCT adslTxFilterConfig	1.3.6.1.4.1.193.72.300.10.1.25	OCTET STRING	read-write	TxFilter in ADSL chipset. The txFilterConfig[1..3] parameter for the C0 and B0 version of the chipset. Bytes [0..2] for CO version and bytes [3..5] for B0 version. NOTE: This parameter must be set from the configuration file to take effect!
OCT adslTxFilterActual	1.3.6.1.4.1.193.72.300.10.1.26	OCTET STRING	read-only	TxFilter in ADSL chipset. The value of the txFilterConfig[1..3] acually used in the ADSL chipset.
OCT adslPowerModes	1.3.6.1.4.1.193.72.300.10.1.27	OCTET STRING	read-write	Power Modes in DSL chipset. The PowerModeData[] in the IP DSLAM uses these indexes: POWERDOWN = 0 ACTIVATION = 1 SHOWTIME_256 = 2 LINETEST = 3 SHOWTIME_512 = 4 SHOWTIME_1024 = 5 SHOWTIME_2048 = 6 SHOWTIME_4096 = 7 NOTE: This parameter must be set from the configuration file to take effect!
I32 adslTxPowerCalibration	1.3.6.1.4.1.193.72.300.10.1.28	Integer32	read-write	Tuning the transmit power in ADSL chipset. Unit is 1/256 dB. Range ]-2,+3[ dB which corresponds to ]-512,+768[. NOTE: This parameter must be set from the configuration file to take effect!
I32 adslRxPowerCalibration	1.3.6.1.4.1.193.72.300.10.1.29	Integer32	read-write	Tuning the received reference power in ADSL chipset. Unit is 1/256 dB. Range [ -5 dB, 10 dB] which corresponds to [ -1280, +2560]. NOTE: This parameter must be set from the configuration file to take effect! To be substituted by adslRxAfeGains for HMI 9.x
INT adslLineStateLedControl	1.3.6.1.4.1.193.72.300.10.1.30	INTEGER	read-write	Line state visualisation functionality (green line-LED). If enabled, the chipset controls the line state LEDs. The feature is avalilable in EDN312 only.
OCT adslTxFilterConfigHmi5	1.3.6.1.4.1.193.72.300.10.1.31	OCTET STRING	read-write	TxFilter in ADSL chipset. The txFilterConfig1 - txFilterConfig2 parameter for the C0 and B0 version of the chipset. Bytes [0..1] for CO version and bytes [2..3] for B0 version. NOTE: This parameter must be set from the configuration file to take effect!
OCT adslTxFilterActualHmi5	1.3.6.1.4.1.193.72.300.10.1.32	OCTET STRING	read-only	TxFilter in ADSL chipset. The value of the txFilterConfig1 - txFilterConfig2 acually used in the ADSL chipset.
INT adslEnableDspCoreDump	1.3.6.1.4.1.193.72.300.10.1.33	INTEGER	read-write	When setting this parameter to 1 (true) the the uC does not load firmware image into the DSP after the next DSP reset. The DSP will then be ready for retrieving the DSP core file. Setting this parameter to 0 (false) for normal operation causing the IP DSLAM to autonomously recover from a DSP malfunction.
INT adslEnableACIF	1.3.6.1.4.1.193.72.300.10.1.34	INTEGER	read-write	Custom PSD mask with ACIF LPF. By enabling this feature an extra Tx LPF with a cutoff frequency at 950kHz and >27 dB attenuation above 1.5 MHz is inserted. Valid from: EDA 2.0 SP1 Possible values are: 0 - ACIF disabled 1 - ACIF enabled. Maps into HMI: BCM6410: PhysicalLayerConfig.optionFlags Bit[5]. BCM6411: SetTxFilter(ACIF filter). Note: must be set prior to setting adslIfAdminStatus up
adslAtucPhysXAllocTable	1.3.6.1.4.1.193.72.300.10.1.35		not-accessible	This table provides extra information in relation to the adslAtucPhysTable for DSL lines.
adslAtucPhysXAllocEntry	1.3.6.1.4.1.193.72.300.10.1.35.1		not-accessible	An entry in adslAtucPhysXAllocTable.
OCT adslAtucPhysXBitAllocation	1.3.6.1.4.1.193.72.300.10.1.35.1.1	OCTET STRING	read-only	Upstream bit allocation table.Tones are split in several blocks of 488 tones. Usage: adslAtucPhysXBitAllocation.lineNo.toneIndexPartId I.e. adslAtucPhysXBitAllocation.1.2 contains tones 489-976 on line 1. This parameter does not support lines running VDSL2. Substituded by: vdsl2SCStatusBitsAlloc Deprecated from: EDA 4.0
adslAturPhysXAllocTable	1.3.6.1.4.1.193.72.300.10.1.36		not-accessible	This table provides extra information in relation to the adslAtucPhysTable for DSL lines.
adslAturPhysXAllocEntry	1.3.6.1.4.1.193.72.300.10.1.36.1		not-accessible	An entry in adslAtucPhysXAllocTable.
OCT adslAturPhysXBitAllocation	1.3.6.1.4.1.193.72.300.10.1.36.1.1	OCTET STRING	read-only	Downstream bit allocation table. Tones are split in several blocks of 488 tones. Usage: adslAturPhysXBitAllocation.lineNo.toneIndexPartId I.e. adslAturPhysXBitAllocation.1.2 contains tones 489-976 on line 1. This parameter does not support lines running VDSL2. Substituded by: vdsl2SCStatusBitsAlloc Deprecated from: EDA 4.0
adslAtucPhysXSnrTable	1.3.6.1.4.1.193.72.300.10.1.37		not-accessible	This table provides extra information in relation to the adslAtucPhysTable for DSL lines.
adslAtucPhysXSnrEntry	1.3.6.1.4.1.193.72.300.10.1.37.1		not-accessible	An entry in adslAtucPhysXSnrTable.
OCT adslAtucPhysXToneSnrUs	1.3.6.1.4.1.193.72.300.10.1.37.1.1	OCTET STRING	read-only	Upstream Snr table. Tones are split in several blocks of 244 tones. Each tone Snr value given in 2 octets (little endian). Usage: adslAtucPhysXToneSnrUs.lineNo.toneIndexPartId I.e. adslAtucPhysXBitSnrDs.1.2 contains tones 245-488 on line 1. Substituded by: vdsl2SCStatusSnr Deprecated from: EDA 4.0
adslDeviceConfigData	1.3.6.1.4.1.193.72.300.10.1.39
adslRxAfeGains	1.3.6.1.4.1.193.72.300.10.1.39.1
I32 adslRxAfeGains0	1.3.6.1.4.1.193.72.300.10.1.39.1.1	Integer32	read-write	Fine tune received power (1/256 dB). Used to indicate the attenuation of the received analog front-end between the line and ADC for an AGC gain of 0 dB. Unit is 1/256 dB. The allowed range is [-25, -10] dB. -rxAfeGains0: attenuation in US0 band over POTS -rxAfeGains1: attenuation in US0 band over ISDN -rxAfeGains2: attenuation in US1 band (only forG.992.3) -rxAfeGains3: attenuation in US2 band (only for G.992.3) Substitutes adslRxPowerCalibration.
I32 adslRxAfeGains1	1.3.6.1.4.1.193.72.300.10.1.39.1.2	Integer32	read-write	Fine tune received power (1/256 dB). Used to indicate the attenuation of the received analog front-end between the line and ADC for an AGC gain of 0 dB. Unit is 1/256 dB. The allowed range is [-25, -10] dB. -rxAfeGains0: attenuation in US0 band over POTS -rxAfeGains1: attenuation in US0 band over ISDN -rxAfeGains2: attenuation in US1 band (only forG.992.3) -rxAfeGains3: attenuation in US2 band (only for G.992.3) Substitutes adslRxPowerCalibration.
I32 adslRxAfeGains2	1.3.6.1.4.1.193.72.300.10.1.39.1.3	Integer32	read-write	Fine tune received power (1/256 dB). Used to indicate the attenuation of the received analog front-end between the line and ADC for an AGC gain of 0 dB. Unit is 1/256 dB. The allowed range is [-25, -10] dB. -rxAfeGains0: attenuation in US0 band over POTS -rxAfeGains1: attenuation in US0 band over ISDN -rxAfeGains2: attenuation in US1 band (only forG.992.3) -rxAfeGains3: attenuation in US2 band (only for G.992.3) Substitutes adslRxPowerCalibration.
I32 adslRxAfeGains3	1.3.6.1.4.1.193.72.300.10.1.39.1.4	Integer32	read-write	Fine tune received power (1/256 dB). Used to indicate the attenuation of the received analog front-end between the line and ADC for an AGC gain of 0 dB. Unit is 1/256 dB. The allowed range is [-25, -10] dB. -rxAfeGains0: attenuation in US0 band over POTS -rxAfeGains1: attenuation in US0 band over ISDN -rxAfeGains2: attenuation in US1 band (only forG.992.3) -rxAfeGains3: attenuation in US2 band (only for G.992.3) Substitutes adslRxPowerCalibration.
adslAgcGains	1.3.6.1.4.1.193.72.300.10.1.39.2
I32 adslAgcGains0	1.3.6.1.4.1.193.72.300.10.1.39.2.1	Integer32	read-write	Fine tune AGC gains (1/256 dB). The agcGains(i), i = 0..6, is used to indicate the real gain of the AGC for a nominal value of (6 * i -12) dB with respect to the AGC setting of 0 dB (agcGains[2] is always equal to 0). Range: [-18, 24] dB
I32 adslAgcGains1	1.3.6.1.4.1.193.72.300.10.1.39.2.2	Integer32	read-write	Fine tune AGC gains (1/256 dB). The agcGains[i], i = 0..6, is used to indicate the real gain of the AGC for a nominal value of (6 * i -12) dB with respect to the AGC setting of 0 dB (agcGains[2] is always equal to 0). Range: [-18, 24] dB
I32 adslAgcGains2	1.3.6.1.4.1.193.72.300.10.1.39.2.3	Integer32	read-write	Fine tune AGC gains (1/256 dB). The agcGains[i], i = 0..6, is used to indicate the real gain of the AGC for a nominal value of (6 * i -12) dB with respect to the AGC setting of 0 dB (agcGains[2] is always equal to 0). Range: [-18, 24] dB
I32 adslAgcGains3	1.3.6.1.4.1.193.72.300.10.1.39.2.4	Integer32	read-write	Fine tune AGC gains (1/256 dB). The agcGains[i], i = 0..6, is used to indicate the real gain of the AGC for a nominal value of (6 * i -12) dB with respect to the AGC setting of 0 dB (agcGains[2] is always equal to 0). Range: [-18, 24] dB
I32 adslAgcGains4	1.3.6.1.4.1.193.72.300.10.1.39.2.5	Integer32	read-write	Fine tune AGC gains (1/256 dB). The agcGains[i], i = 0..6, is used to indicate the real gain of the AGC for a nominal value of (6 * i -12) dB with respect to the AGC setting of 0 dB (agcGains[2] is always equal to 0). Range: [-18, 24] dB
I32 adslAgcGains5	1.3.6.1.4.1.193.72.300.10.1.39.2.6	Integer32	read-write	Fine tune AGC gains (1/256 dB). The agcGains[i], i = 0..6, is used to indicate the real gain of the AGC for a nominal value of (6 * i -12) dB with respect to the AGC setting of 0 dB (agcGains[2] is always equal to 0). Range: [-18, 24] dB
I32 adslAgcGains6	1.3.6.1.4.1.193.72.300.10.1.39.2.7	Integer32	read-write	Fine tune AGC gains (1/256 dB). The agcGains[i], i = 0..6, is used to indicate the real gain of the AGC for a nominal value of (6 * i -12) dB with respect to the AGC setting of 0 dB (agcGains[2] is always equal to 0). Range: [-18, 24] dB
adslAtuc1DayIntervalXTable	1.3.6.1.4.1.193.72.300.10.1.45		not-accessible	This table provides one row for each ATUC performance data collection in a 1 day measurement interval. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94).
adslAtuc1DayIntervalXEntry	1.3.6.1.4.1.193.72.300.10.1.45.1		not-accessible	An entry in the adslAtuc1DayIntervalXTable.
INT adslAtuc1DayIntervalXNumber	1.3.6.1.4.1.193.72.300.10.1.45.1.1	INTEGER	not-accessible	Performance Data Interval number 1 is the most recent previous 1 day interval.
NUM adslAtuc1DayIntervalXLofs	1.3.6.1.4.1.193.72.300.10.1.45.1.5	Perf1DayIntervalXCount	read-only	Count of seconds in the interval when there was Loss of Framing.
NUM adslAtuc1DayIntervalXLoss	1.3.6.1.4.1.193.72.300.10.1.45.1.10	Perf1DayIntervalXCount	read-only	Count of seconds in the interval when there was Loss of Signal.
NUM adslAtuc1DayIntervalXLols	1.3.6.1.4.1.193.72.300.10.1.45.1.15	Perf1DayIntervalXCount	read-only	Count of seconds in the interval when there was Loss of Link.
NUM adslAtuc1DayIntervalXESs	1.3.6.1.4.1.193.72.300.10.1.45.1.20	Perf1DayIntervalXCount	read-only	Count of Errored Seconds in the interval. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.
NUM adslAtuc1DayIntervalXEcs	1.3.6.1.4.1.193.72.300.10.1.45.1.25	Perf1DayIntervalXCount	read-only	Count of forward error correction seconds in the interval.
NUM adslAtuc1DayIntervalXInits	1.3.6.1.4.1.193.72.300.10.1.45.1.30	Perf1DayIntervalXCount	read-only	Count of the line initialization attempts during the interval. Includes both successful and failed attempts.
T/F adslAtuc1DayIntervalXValidData	1.3.6.1.4.1.193.72.300.10.1.45.1.35	TruthValue	read-only	This variable indicates if the data for this interval is valid.
adslAtur1DayIntervalXTable	1.3.6.1.4.1.193.72.300.10.1.50		not-accessible	This table provides one row for each ATUR performance data collection in a 1 day measurement interval. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94).
adslAtur1DayIntervalXEntry	1.3.6.1.4.1.193.72.300.10.1.50.1		not-accessible	An entry in the adslAtur1DayIntervalXTable.
INT adslAtur1DayIntervalXNumber	1.3.6.1.4.1.193.72.300.10.1.50.1.1	INTEGER	not-accessible	Performance Data Interval number 1 is the most recent previous 1 day interval.
NUM adslAtur1DayIntervalXLofs	1.3.6.1.4.1.193.72.300.10.1.50.1.5	Perf1DayIntervalXCount	read-only	Count of seconds in the interval when there was Loss of Framing.
NUM adslAtur1DayIntervalXLoss	1.3.6.1.4.1.193.72.300.10.1.50.1.10	Perf1DayIntervalXCount	read-only	Count of seconds in the interval when there was Loss of Signal.
NUM adslAtur1DayIntervalXLprs	1.3.6.1.4.1.193.72.300.10.1.50.1.15	Perf1DayIntervalXCount	read-only	Count of seconds in the interval when there was Loss of Power.
NUM adslAtur1DayIntervalXESs	1.3.6.1.4.1.193.72.300.10.1.50.1.20	Perf1DayIntervalXCount	read-only	Count of Errored Seconds in the interval. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.
NUM adslAtur1DayIntervalXEcs	1.3.6.1.4.1.193.72.300.10.1.50.1.25	Perf1DayIntervalXCount	read-only	Count of forward error correction seconds in the interval.
T/F adslAtur1DayIntervalXValidData	1.3.6.1.4.1.193.72.300.10.1.50.1.30	TruthValue	read-only	This variable indicates if the data for this interval is valid.
adslAtucChan1DayIntervalXTable	1.3.6.1.4.1.193.72.300.10.1.55		not-accessible	This table provides one row for each ATUC channel's performance data collection in a 1 day measurement interval. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125).
adslAtucChan1DayIntervalXEntry	1.3.6.1.4.1.193.72.300.10.1.55.1		not-accessible	An entry in the adslAtucChan1DayIntervalXTable.
INT adslAtucChan1DayIntervalXNumber	1.3.6.1.4.1.193.72.300.10.1.55.1.1	INTEGER	not-accessible	Performance Data Interval number 1 is the most recent previous 1 day interval.
NUM adslAtucChan1DayIntervalXCorrectedBlks	1.3.6.1.4.1.193.72.300.10.1.55.1.5	Perf1DayIntervalXCount	read-only	Count of all blocks received with errors that were corrected on this channel during this interval.
NUM adslAtucChan1DayIntervalXUncorrectBlks	1.3.6.1.4.1.193.72.300.10.1.55.1.10	Perf1DayIntervalXCount	read-only	Count of all blocks received with uncorrectable errors on this channel during this interval.
NUM adslAtucChan1DayIntervalXHecv	1.3.6.1.4.1.193.72.300.10.1.55.1.15	Perf1DayIntervalXCount	read-only	Count of all header error correction violations received on this channel during this interval.
NUM adslAtucChan1DayIntervalXTotalCells	1.3.6.1.4.1.193.72.300.10.1.55.1.20	Perf1DayIntervalXCount	read-only	Count of all ATM cells received on this channel during this interval.
NUM adslAtucChan1DayIntervalXTotalUserCells	1.3.6.1.4.1.193.72.300.10.1.55.1.25	Perf1DayIntervalXCount	read-only	Count of all valid non-idle ATM cells succesfully transmitted to the UTOPIA bus on this interval.
NUM adslAtucChan1DayIntervalXOverFlowCells	1.3.6.1.4.1.193.72.300.10.1.55.1.30	Perf1DayIntervalXCount	read-only	Count the number of cells discarded due to the received UTOPIA FIFO being full on this interval.
NUM adslAtucChan1DayIntervalXIdleCells	1.3.6.1.4.1.193.72.300.10.1.55.1.35	Perf1DayIntervalXCount	read-only	Count of all idle ATM cells received on this channel this interval.
NUM adslAtucChan1DayIntervalXIdleCellBitErrors	1.3.6.1.4.1.193.72.300.10.1.55.1.40	Perf1DayIntervalXCount	read-only	Count the number of bit errors in the payload of the valid idle ATM cells received on this channel on this interval.
T/F adslAtucChan1DayIntervalXValidData	1.3.6.1.4.1.193.72.300.10.1.55.1.45	TruthValue	read-only	This variable indicates if the data for this interval is valid.
adslAturChan1DayIntervalXTable	1.3.6.1.4.1.193.72.300.10.1.60		not-accessible	This table provides one row for each ATUR channel's performance data collection in a 1 day measurement interval. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125).
adslAturChan1DayIntervalXEntry	1.3.6.1.4.1.193.72.300.10.1.60.1		not-accessible	An entry in the adslAturChan1DayIntervalXTable.
INT adslAturChan1DayIntervalXNumber	1.3.6.1.4.1.193.72.300.10.1.60.1.1	INTEGER	not-accessible	Performance Data Interval number 1 is the most recent previous 1 day interval.
NUM adslAturChan1DayIntervalXCorrectedBlks	1.3.6.1.4.1.193.72.300.10.1.60.1.5	Perf1DayIntervalXCount	read-only	Count of all blocks received with errors that were corrected on this channel during this interval.
NUM adslAturChan1DayIntervalXUncorrectBlks	1.3.6.1.4.1.193.72.300.10.1.60.1.10	Perf1DayIntervalXCount	read-only	Count of all blocks received with uncorrectable errors on this channel during this interval.
NUM adslAturChan1DayIntervalXHecv	1.3.6.1.4.1.193.72.300.10.1.60.1.15	Perf1DayIntervalXCount	read-only	Count of all header error correction violations received on this channel during this interval.
NUM adslAturChan1DayIntervalXTotalCells	1.3.6.1.4.1.193.72.300.10.1.60.1.20	Perf1DayIntervalXCount	read-only	Count of all ATM cells received on this channel this interval.
NUM adslAturChan1DayIntervalXTotalUserCells	1.3.6.1.4.1.193.72.300.10.1.60.1.25	Perf1DayIntervalXCount	read-only	Count of all valid non-idle ATM cells succesfully received on the UTOPIA bus on this interval.
NUM adslAturChan1DayIntervalXIdleCellBitErrors	1.3.6.1.4.1.193.72.300.10.1.60.1.30	Perf1DayIntervalXCount	read-only	Count the number of bit errors in the payload of the valid idle ATM cells received on this channel on this interval. Applies to ADSL2 only.
T/F adslAturChan1DayIntervalXValidData	1.3.6.1.4.1.193.72.300.10.1.60.1.35	TruthValue	read-only	This variable indicates if the data for this interval is valid.
TON tonePartIdIndex	1.3.6.1.4.1.193.72.300.10.1.65	TonePartIdIndex	not-accessible	The Tone Part ID index.
adslXTraps	1.3.6.1.4.1.193.72.300.10.2
adslAtucXTraps	1.3.6.1.4.1.193.72.300.10.2.1
adslAtucXTrapsEntry	1.3.6.1.4.1.193.72.300.10.2.1.0
NTF adslAtucXInitFailureTrap	1.3.6.1.4.1.193.72.300.10.2.1.0.1			Sent if initialisation of the line failed. One likely reason is that requested configuration can't be implemented on the current line conditions. More information about the reason can be fetched from the current line status. Valid from: EDA 1.1R2A Parameters 1: Managed object class IP DSLAM Port 2: Managed object ID (MAC + PortNo) 3: Sequence number (Alarm sequence number) 4: Perceived severity Major 5: Event time (Timestamp is retrieved from a SNTP server) 6: Event type ProcessingErrorAlarm 7: Probable cause ConfigurationOrCustomisationError 8: Err Code (Additional error information)
NTF adslAtucIncorrectConfigurationTrap	1.3.6.1.4.1.193.72.300.10.2.1.0.2			The current configuration is not allowed. The operator must change the configuration settings. Valid from: EDA 1.1R2A Parameters 1: Managed object class IP DSLAM Port 2: Managed object ID (MAC + PortNo) 3: Sequence number (Alarm sequence number) 4: Perceived severity Major 5: Event time (Timestamp is retrieved from a SNTP server) 6: Event type ProcessingErrorAlarm 7: Probable cause ConfigurationOrCustomisationError 8: Message ID (Internal message number) 9: Err Code (Additional error information)
NTF adslAtucPerfXESsThresh15MinTrap	1.3.6.1.4.1.193.72.300.10.2.1.0.3			Errored Second 15-minute interval threshold reached. Valid from: EDA 1.1R2A Parameters 1: Managed object class IP DSLAM Port 2: Managed object ID (MAC + PortNo) 3: Sequence number (Alarm sequence number) 4: Perceived severity Warning 5: Event time (Timestamp is retrieved from a SNTP server) 6: Event type QualityOfServiceAlarm 7: Probable cause TransmissionError 8: Threshold parameter (adslAtucThresh15MinESs threshold value)
NTF adslAtucPerfXESsThresh1DayTrap	1.3.6.1.4.1.193.72.300.10.2.1.0.4			Errored Second 1 Day interval threshold reached. Valid from: EDA 1.1R2A Parameters 1: Managed object class IP DSLAM Port 2: Managed object ID (MAC + PortNo) 3: Sequence number (Alarm sequence number) 4: Perceived severity Warning 5: Event time (Timestamp is retrieved from a SNTP server) 6: Event type QualityOfServiceAlarm 7: Probable cause TransmissionError 8: Threshold parameter (adslAlarmConfXAtucThres1DayES threshold value)
NTF adslAtucPerfXSesThresh15MinTrap	1.3.6.1.4.1.193.72.300.10.2.1.0.5			Severely Errored Second 15-minute interval threshold reached. Valid from: EDA 1.1R2A Parameters 1: Managed object class IP DSLAM Port 2: Managed object ID (MAC + PortNo) 3: Sequence number (Alarm sequence number) 4: Perceived severity Warning 5: Event time (Timestamp is retrieved from a SNTP server) 6: Event type QualityOfServiceAlarm 7: Probable cause TransmissionError 8: Threshold parameter (adslAtucThreshold15MinSesL threshold value)
NTF adslAtucPerfXSesThresh1DayTrap	1.3.6.1.4.1.193.72.300.10.2.1.0.6			Severely Errored Second 1 Day interval threshold reached. Valid from: EDA 1.1R2A Parameters 1: Managed object class IP DSLAM Port 2: Managed object ID (MAC + PortNo) 3: Sequence number (Alarm sequence number) 4: Perceived severity Warning 5: Event time (Timestamp is retrieved from a SNTP server) 6: Event type QualityOfServiceAlarm 7: Probable cause TransmissionError 8: Threshold parameter (adslAlarmConfXAtucThres1DaySesL threshold value)
NTF adslAtucPerfXUasThresh15MinTrap	1.3.6.1.4.1.193.72.300.10.2.1.0.7			Unavailable Second 15-minute interval threshold reached. Valid from: EDA 1.1R2A Parameters 1: Managed object class IP DSLAM Port 2: Managed object ID (MAC + PortNo) 3: Sequence number (Alarm sequence number) 4: Perceived severity Warning 5: Event time (Timestamp is retrieved from a SNTP server) 6: Event type QualityOfServiceAlarm 7: Probable cause TransmissionError 8: Threshold parameter (adslAtucThreshold15MinUasL threshold value)
NTF adslAtucPerfXUasThresh1DayTrap	1.3.6.1.4.1.193.72.300.10.2.1.0.8			Unavailable Second 1 Day interval threshold reached. Valid from: EDA 1.1R2A Parameters 1: Managed object class IP DSLAM Port 2: Managed object ID (MAC + PortNo) 3: Sequence number (Alarm sequence number) 4: Perceived severity Warning 5: Event time (Timestamp is retrieved from a SNTP server) 6: Event type QualityOfServiceAlarm 7: Probable cause TransmissionError 8: Threshold parameter (adslAlarmConfXAtucThres1DayUasL threshold value)
NTF adslAtucDspUnexpectedResponseTrap	1.3.6.1.4.1.193.72.300.10.2.1.0.9			DSP replies with an unexpected result code such as: 'unknown application id', 'unknown command id', 'wrong message format', 'request data not valid' or 'request cannot be performed in current state'. This should not happen and comes from either incompatible SW versions or state mismatch between UC and DSP due to internal SW problems. If necessary a LinkDown should proceed this fault.The line will be reset and possibly taken into service again. In case too many line resets have been performed a DSP Communication Failure shall be triggered and the DSP reset and reloaded. The operator must change the configuration settings. Valid from: EDA 1.1R2A Parameters 1: Managed object class IP DSLAM Port 2: Managed object ID (MAC + PortNo) 3: Sequence number (Alarm sequence number) 4: Perceived severity Minor 5: Event time (Timestamp is retrieved from a SNTP server) 6: Event type Equipment 7: Probable cause UnexpectedInformation 8: Message ID (Internal message number) 9: Err Code (Additional error information)
NTF adslAtucDspLineResetTrap	1.3.6.1.4.1.193.72.300.10.2.1.0.10			The indicated line has autonomously reset itself. This should not occur and can be due to CPU overload or some other internal DSP SW failure. If necessary a LinkDown should proceed this fault. The line will be reset and possibly taken into service again. In case too many line resets have been performed a DSP Communication Failure shall be triggered and the DSP reset and reloaded. Valid from: EDA 1.1R2A Parameters 1: Managed object class IP DSLAM Port 2: Managed object ID (MAC + PortNo) 3: Sequence number (Alarm sequence number) 4: Perceived severity Minor 5: Event time (Timestamp is retrieved from a SNTP server) 6: Event type ProcessingErrorAlarm 7: Probable cause EquipmentMalfunction
NTF adslAtucLineQualityThreshNotReachedTrap	1.3.6.1.4.1.193.72.300.10.2.1.0.11			Line Quality threshold not reached. Valid from: EDA 2.1 Parameters 1: Managed object class IP DSLAM Port 2: Managed object ID (MAC + PortNo) 3: Sequence number (Alarm sequence number) 4: Perceived severity Warning 5: Event time (Timestamp is retrieved from a SNTP server) 6: Event type QualityOfServiceAlarm 7: Probable cause ThresholdCrossed 8: Threshold Line quality alarm threshold
NTF adslAtucLineBondLineQualityThreshNotReachedTrap	1.3.6.1.4.1.193.72.300.10.2.1.0.12			Line Quality threshold not reached. Valid from: EDA 2.2 Parameters 1: Managed object class IP DSLAM Port 2: Managed object ID (MAC + PortNo) 3: Sequence number (Alarm sequence number) 4: Perceived severity Warning 5: Event time (Timestamp is retrieved from a SNTP server) 6: Event type QualityOfServiceAlarm 7: Probable cause ThresholdCrossed 8: Threshold Line quality alarm threshold
NTF adslAtucPerfXLofsThresh15MinTrap	1.3.6.1.4.1.193.72.300.10.2.1.0.15			Count of Loss of Frame seconds in current 15-minute interval has reached the threshold value configured by the adslAtucThresh15MinLofs parameter. Valid from: EDA 2.2 MA2 Parameters 1: Managed object class IP DSLAM Port 2: Managed object ID (MAC + PortNo) 3: Sequence number (Alarm sequence number) 4: Perceived severity Warning 5: Event time (Timestamp is retrieved from a SNTP server) 6: Event type QualityOfServiceAlarm 7: Probable cause TransmissionError 8: Threshold parameter (adslAtucThresh15MinLofs threshold value)
NTF adslAtucPerfXLofsThresh1DayTrap	1.3.6.1.4.1.193.72.300.10.2.1.0.20			Count of Loss of Frame seconds in current 1-day interval has reached the threshold value configured by adslAlarmConfXAtucThres1DayLofs parameter. Valid from: EDA 2.2 MA2 Parameters 1: Managed object class IP DSLAM Port 2: Managed object ID (MAC + PortNo) 3: Sequence number (Alarm sequence number) 4: Perceived severity Warning 5: Event time (Timestamp is retrieved from a SNTP server) 6: Event type QualityOfServiceAlarm 7: Probable cause TransmissionError 8: Threshold parameter (adslAlarmConfXAtucThres1DayLofs threshold value)
NTF adslAtucPerfXLossThresh15MinTrap	1.3.6.1.4.1.193.72.300.10.2.1.0.25			Count of Loss of Signal seconds in current 15-minute interval has reached the threshold value configured by the adslAtucThresh15MinLoss parameter. Valid from: EDA 2.2 MA2 Parameters 1: Managed object class IP DSLAM Port 2: Managed object ID (MAC + PortNo) 3: Sequence number (Alarm sequence number) 4: Perceived severity Warning 5: Event time (Timestamp is retrieved from a SNTP server) 6: Event type QualityOfServiceAlarm 7: Probable cause TransmissionError 8: Threshold parameter (adslAtucThresh15MinLoss threshold value)
NTF adslAtucPerfXLossThresh1DayTrap	1.3.6.1.4.1.193.72.300.10.2.1.0.30			Count of Loss of Signal seconds in current 1-day interval has reached the threshold value configured by adslAlarmConfXAtucThres1DayLoss parameter. Valid from: EDA 2.2 MA2 Parameters 1: Managed object class IP DSLAM Port 2: Managed object ID (MAC + PortNo) 3: Sequence number (Alarm sequence number) 4: Perceived severity Warning 5: Event time (Timestamp is retrieved from a SNTP server) 6: Event type QualityOfServiceAlarm 7: Probable cause TransmissionError 8: Threshold parameter (adslAlarmConfXAtucThres1DayLoss threshold value)
NTF adslAtucPerfXLolsThresh15MinTrap	1.3.6.1.4.1.193.72.300.10.2.1.0.35			Count of Loss of Link seconds in current 15-minute interval has reached the threshold value configured by the adslAtucThresh15MinLols parameter. Valid from: EDA 2.2 MA2 Parameters 1: Managed object class IP DSLAM Port 2: Managed object ID (MAC + PortNo) 3: Sequence number (Alarm sequence number) 4: Perceived severity Warning 5: Event time (Timestamp is retrieved from a SNTP server) 6: Event type QualityOfServiceAlarm 7: Probable cause TransmissionError 8: Threshold parameter (adslAtucThresh15MinLols threshold value)
NTF adslAtucPerfXLolsThresh1DayTrap	1.3.6.1.4.1.193.72.300.10.2.1.0.40			Count of Loss of Link seconds in current 1-day interval has reached the threshold value configured by adslAlarmConfXAtucThres1DayLols parameter. Valid from: EDA 2.2 MA2 Parameters 1: Managed object class IP DSLAM Port 2: Managed object ID (MAC + PortNo) 3: Sequence number (Alarm sequence number) 4: Perceived severity Warning 5: Event time (Timestamp is retrieved from a SNTP server) 6: Event type QualityOfServiceAlarm 7: Probable cause TransmissionError 8: Threshold parameter (adslAlarmConfXAtucThres1DayLols threshold value)
adslAturXTraps	1.3.6.1.4.1.193.72.300.10.2.2
adslAturXTrapsEntry	1.3.6.1.4.1.193.72.300.10.2.2.0
NTF adslAturPerfXESsThresh15MinTrap	1.3.6.1.4.1.193.72.300.10.2.2.0.2			Errored Second 15-minute interval threshold reached. Valid from: EDA 1.1R2A Parameters 1: Managed object class IP DSLAM Port 2: Managed object ID (MAC + PortNo) 3: Sequence number (Alarm sequence number) 4: Perceived severity Warning 5: Event time (Timestamp is retrieved from a SNTP server) 6: Event type QualityOfServiceAlarm 7: Probable cause TransmissionError 8: Threshold parameter (adslAturThresh15MinESs threshold value)
NTF adslAturPerfXESsThresh1DayTrap	1.3.6.1.4.1.193.72.300.10.2.2.0.3			Errored Second 1 Day interval threshold reached. Valid from: EDA 1.1R2A Parameters 1: Managed object class IP DSLAM Port 2: Managed object ID (MAC + PortNo) 3: Sequence number (Alarm sequence number) 4: Perceived severity Warning 5: Event time (Timestamp is retrieved from a SNTP server) 6: Event type QualityOfServiceAlarm 7: Probable cause TransmissionError 8: Threshold parameter (adslAlarmConfXAturThres1DayES threshold value)
NTF adslAturPerfXSesThresh15MinTrap	1.3.6.1.4.1.193.72.300.10.2.2.0.4			Severely Errored Second 15-minute interval threshold reached. Valid from: EDA 1.1R2A Parameters 1: Managed object class IP DSLAM Port 2: Managed object ID (MAC + PortNo) 3: Sequence number (Alarm sequence number) 4: Perceived severity Warning 5: Event time (Timestamp is retrieved from a SNTP server) 6: Event type QualityOfServiceAlarm 7: Probable cause TransmissionError 8: Threshold parameter (adslAturThreshold15MinSesL threshold value)
NTF adslAturPerfXSesThresh1DayTrap	1.3.6.1.4.1.193.72.300.10.2.2.0.5			Severely Errored Second 1 Day interval threshold reached. Valid from: EDA 1.1R2A Parameters 1: Managed object class IP DSLAM Port 2: Managed object ID (MAC + PortNo) 3: Sequence number (Alarm sequence number) 4: Perceived severity Warning 5: Event time (Timestamp is retrieved from a SNTP server) 6: Event type QualityOfServiceAlarm 7: Probable cause TransmissionError 8: Threshold parameter (adslAlarmConfXAturThres1DaySesL threshold value)
NTF adslAturPerfXUasThresh15MinTrap	1.3.6.1.4.1.193.72.300.10.2.2.0.6			Unavailable Second 15-minute interval threshold reached. Valid from: EDA 1.1R2A Parameters 1: Managed object class IP DSLAM Port 2: Managed object ID (MAC + PortNo) 3: Sequence number (Alarm sequence number) 4: Perceived severity Warning 5: Event time (Timestamp is retrieved from a SNTP server) 6: Event type QualityOfServiceAlarm 7: Probable cause TransmissionError 8: Threshold parameter (adslAturThreshold15MinUasL threshold value)
NTF adslAturPerfXUasThresh1DayTrap	1.3.6.1.4.1.193.72.300.10.2.2.0.7			Unavailable Second 1 Day interval threshold reached. Valid from: EDA 1.1R2A Parameters 1: Managed object class IP DSLAM Port 2: Managed object ID (MAC + PortNo) 3: Sequence number (Alarm sequence number) 4: Perceived severity Warning 5: Event time (Timestamp is retrieved from a SNTP server) 6: Event type QualityOfServiceAlarm 7: Probable cause TransmissionError 8: Threshold parameter (adslAlarmConfXAturThres1DayUasL threshold value)
NTF adslAturLineQualityThreshNotReachedTrap	1.3.6.1.4.1.193.72.300.10.2.2.0.8			Line Quality threshold not reached. Valid from: EDA 2.1 Parameters 1: Managed object class IP DSLAM Port 2: Managed object ID (MAC + PortNo) 3: Sequence number (Alarm sequence number) 4: Perceived severity Warning 5: Event time (Timestamp is retrieved from a SNTP server) 6: Event type QualityOfServiceAlarm 7: Probable cause ThresholdCrossed 8: Threshold Line quality alarm threshold
NTF adslAturLineBondLineQualityThreshNotReachedTrap	1.3.6.1.4.1.193.72.300.10.2.2.0.9			Line Quality threshold not reached. Valid from: EDA 2.2 Parameters 1: Managed object class IP DSLAM Port 2: Managed object ID (MAC + PortNo) 3: Sequence number (Alarm sequence number) 4: Perceived severity Warning 5: Event time (Timestamp is retrieved from a SNTP server) 6: Event type QualityOfServiceAlarm 7: Probable cause ThresholdCrossed 8: Threshold Line quality alarm threshold
NTF adslAturPerfXLofsThresh15MinTrap	1.3.6.1.4.1.193.72.300.10.2.2.0.15			Count of Loss of Frame seconds in current 15-minute interval has reached the threshold value configured by the adslAturThresh15MinLofs parameter. Valid from: EDA 2.2 MA2 Parameters 1: Managed object class IP DSLAM Port 2: Managed object ID (MAC + PortNo) 3: Sequence number (Alarm sequence number) 4: Perceived severity Warning 5: Event time (Timestamp is retrieved from a SNTP server) 6: Event type QualityOfServiceAlarm 7: Probable cause TransmissionError 8: Threshold parameter (adslAturThresh15MinLofs threshold value)
NTF adslAturPerfXLofsThresh1DayTrap	1.3.6.1.4.1.193.72.300.10.2.2.0.20			Count of Loss of Frame seconds in current 1-day interval has reached the threshold value configured by the adslAlarmConfXAturThres1DayLofs parameter. Valid from: EDA 2.2 MA2 Parameters 1: Managed object class IP DSLAM Port 2: Managed object ID (MAC + PortNo) 3: Sequence number (Alarm sequence number) 4: Perceived severity Warning 5: Event time (Timestamp is retrieved from a SNTP server) 6: Event type QualityOfServiceAlarm 7: Probable cause TransmissionError 8: Threshold parameter (adslAlarmConfXAturThres1DayLofs threshold value)
NTF adslAturPerfXLossThresh15MinTrap	1.3.6.1.4.1.193.72.300.10.2.2.0.25			Count of Loss of Signal seconds in current 15-minute interval has reached the threshold value configured by the adslAturThresh15MinLoss parameter. Valid from: EDA 2.2 MA2 Parameters 1: Managed object class IP DSLAM Port 2: Managed object ID (MAC + PortNo) 3: Sequence number (Alarm sequence number) 4: Perceived severity Warning 5: Event time (Timestamp is retrieved from a SNTP server) 6: Event type QualityOfServiceAlarm 7: Probable cause TransmissionError 8: Threshold parameter (adslAturThresh15MinLoss threshold value)
NTF adslAturPerfXLossThresh1DayTrap	1.3.6.1.4.1.193.72.300.10.2.2.0.30			Count of Loss of Signal seconds in current 1-day interval has reached the threshold value configured by the adslAlarmConfXAturThres1DayLoss parameter. Valid from: EDA 2.2 MA2 Parameters 1: Managed object class IP DSLAM Port 2: Managed object ID (MAC + PortNo) 3: Sequence number (Alarm sequence number) 4: Perceived severity Warning 5: Event time (Timestamp is retrieved from a SNTP server) 6: Event type QualityOfServiceAlarm 7: Probable cause TransmissionError 8: Threshold parameter (adslAlarmConfXAturThres1DayLoss threshold value)
NTF adslAturPerfXLprsThresh15MinTrap	1.3.6.1.4.1.193.72.300.10.2.2.0.35			Count of Loss of Power seconds in current 15-minute interval has reached the threshold value configured by the adslAtucThresh15MinLprs parameter. Valid from: EDA 2.2 MA2 Parameters 1: Managed object class IP DSLAM Port 2: Managed object ID (MAC + PortNo) 3: Sequence number (Alarm sequence number) 4: Perceived severity Warning 5: Event time (Timestamp is retrieved from a SNTP server) 6: Event type QualityOfServiceAlarm 7: Probable cause TransmissionError 8: Threshold parameter (adslAturThresh15MinLprs threshold value)
NTF adslAturPerfXLprsThresh1DayTrap	1.3.6.1.4.1.193.72.300.10.2.2.0.40			Count of Loss of Power seconds in current 1-day interval has reached the threshold value configured by the adslAlarmConfXAturThres1DayLprs parameter. Valid from: EDA 2.2 MA2 Parameters 1: Managed object class IP DSLAM Port 2: Managed object ID (MAC + PortNo) 3: Sequence number (Alarm sequence number) 4: Perceived severity Warning 5: Event time (Timestamp is retrieved from a SNTP server) 6: Event type QualityOfServiceAlarm 7: Probable cause TransmissionError 8: Threshold parameter (adslAlarmConfXAturThres1DayLprs threshold value)
adslDeviceTraps	1.3.6.1.4.1.193.72.300.10.2.3
adslDeviceTrapsEntry	1.3.6.1.4.1.193.72.300.10.2.3.0
NTF adslDspLoadingFailureTrap	1.3.6.1.4.1.193.72.300.10.2.3.0.1			DSP software could not be loaded and started, either incompatible or inoperable HW, damaged or wrong load file. ADSL system inoperable. Valid from: EDA 1.1R2A Parameters 1: Managed object class IP DSLAM 2: Managed object ID (MAC) 3: Sequence number (Alarm sequence number) 4: Perceived severity Critical 5: Event time (Timestamp is retrieved from a SNTP server) 6: Event type Equipment 7: Probable cause EquipmentMalfunction
NTF adslDspCommunicationFailureTrap	1.3.6.1.4.1.193.72.300.10.2.3.0.3			DSP does not reply to a request or too many DSP Unexpected Response Failures have been detected. DSP will be reset and reloaded. Affects all lines in the IP DSLAM. Valid from: EDA 1.1R2A Parameters 1: Managed object class IP DSLAM 2: Managed object ID (MAC) 3: Sequence number (Alarm sequence number) 4: Perceived severity Major 5: Event time (Timestamp is retrieved from a SNTP server) 6: Event type CommunicationsAlarm 7: Probable cause SoftwareError
NTF adslDspInoperableTrap	1.3.6.1.4.1.193.72.300.10.2.3.0.4			The DSP has been reloaded and restarted to many times due to errors. ADSL is considered inoperable. In case SW load modules are correct this is most likely a HW problem. Valid from: EDA 1.1R2A Parameters 1: Managed object class IP DSLAM 2: Managed object ID (MAC) 3: Sequence number (Alarm sequence number) 4: Perceived severity Critical 5: Event time (Timestamp is retrieved from a SNTP server) 6: Event type Equipment 7: Probable cause EquipmentMalfunction
NTF adslDspHardwareFailureTrap	1.3.6.1.4.1.193.72.300.10.2.3.0.5			HW failure was detected. HW should be replaced. ADSL system is inoperable. Valid from: EDA 1.1R2A Obsoleted from: EDA 2.2R1A Parameters 1: Managed object class IP DSLAM 2: Managed object ID (MAC) 3: Sequence number (Alarm sequence number) 4: Perceived severity Critical 5: Event time (Timestamp is retrieved from a SNTP server) 6: Event type Equipment 7: Probable cause EquipmentMalfunction
adslXObjectsGroups	1.3.6.1.4.1.193.72.300.10.3
adslXObjectsGroup	1.3.6.1.4.1.193.72.300.10.3.1			Current adslXObjects Group
adslXObjectsDeprecatedGroup	1.3.6.1.4.1.193.72.300.10.3.2			Deprecated adslXObjects Group
adslXObjectsObsoleteGroup	1.3.6.1.4.1.193.72.300.10.3.3			Deprecated adslXObjects Group
adslXTrapsGroups	1.3.6.1.4.1.193.72.300.10.4
adslXTrapsGroup	1.3.6.1.4.1.193.72.300.10.4.1			adslX Traps Group

RFC description

Manages ADSL IP DSLAM equipment including line configuration, threshold monitoring, and performance statistics.

Start monitoring Ericsson IP DSLAM, ADSL access multiplexer (ADSL modem-pair line quality) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download PEA-ADSL-IPDSLAM