NTNTECH-CHASSIS-CONFIGURATION-MIB

All MIBs › NTNTECH-CHASSIS-CONFIGURATION-MIB

Organization: Paradyne Corporation

Last Updated: 2004-11-17

Category: DSL and Broadband Access

Description: Manages chassis slot provisioning, card type assignment, and physical configuration for Paradyne nTech DSL equipment.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is NTNTECH-CHASSIS-CONFIGURATION-MIB?

NTNTECH-CHASSIS-CONFIGURATION-MIB manages the physical chassis configuration of Paradyne Corporation's nTech DSLAM product family, including the MUM200-2/MUM2000-2 modules and Mini/Micro DSLAMs such as the AMD8000-12 and SMD2000-series units, covering slot provisioning and card-type assignment. It exposes chassis- and card-level configuration tables for the multiplexer uplink module and per-line-type interface modules (Ethernet, T1, E1), plus SNMP trap-notification target configuration and authentication trap enable/disable settings. Its monitoring role is primarily configuration/hardware-inventory status: the chassis and interface tables let an operator confirm which card types and line configurations are installed and active in each chassis slot, catching a misconfigured or missing module before it affects DSL service. It underpins, and is used alongside, the companion NTNTECH-INTERFACE-MODULE-CONFIGURATION-MIB, which manages the actual DSL line parameters on those cards. It is deployed on Paradyne/nTech DSLAM chassis in telco central-office or remote-terminal DSL access deployments. Engineers can download the NTNTECH-CHASSIS-CONFIGURATION-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in NTNTECH-CHASSIS-CONFIGURATION-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Paradyne nTech DSLAM chassis (Mini/Micro DSLAM)
MUM200-2/MUM2000-2 multiplexer module

Monitoring Examples

An operator polls mumCfgTable to confirm the installed multiplexer uplink module type in a chassis slot, then checks uimCfgT1Table or uimCfgE1Entry to verify T1/E1 line card configuration matches provisioning records; a mismatch between expected and reported card type in chsCfgParameterConfiguration flags a hardware swap or slot misconfiguration.

What Can Be Monitored

installed card/module type per slot
Ethernet/T1/E1 line card configuration
SNMP trap notification target IPs
authentication trap enable state

Imported Objects

From NTNTECH-ROOT-MIB

NtnDefaultGateway
NtnDisplayString
NtnSubnetMask
NtnTimeTicks
ntntechChassis	OBJECT-IDENTITY

From SNMPv2-SMI

IpAddress
MODULE-IDENTITY
OBJECT-TYPE

From SNMPv2-TC

TEXTUAL-CONVENTION

OIDs

OID symbolic	OID numeric	Type	Access	Description
ntntechChassisConfigurationMIB	1.3.6.1.4.1.8059.1.1.1			This mib module defines an SNMP API to manage the Paradyne Corporation's DSLAM chassis parameters. These parameter settings are specifically associated with the the MUM200-2 and MUM2000-2 modules and the Mini and Micro DSLAMs. The interface types are described below, AMD8000-12 12-Port ADSL Mini DSLAMs With Full Rate and G.lite Operational Modes SMD2000-12, SMD2000Q-12, SMD2000G-12 12-Port SDSL Mini DSLAMs: AC and DC Versions with Cap, 2B1Q and G.SHDSL line encoding SuD2011_12T, SuD2011_12E, SuD2003_12T, SuD2003_12E 12-Port SDSL Micro DSLAMs: Cap, 2B1Q and G.SHDSL line encoding SuD2011_6T, SuD2011_6E, SuD2002_6T, SuD2002_6E 6-Port SDSL Micro DSLAMs: Cap, 2B1Q and G.SHDSL line encoding MUM200-2, MUM2000-2 Multiplexer Uplink Module with Dual Uplink Interface Module Capacity UIM-10/100 Uplink Interface Module UIM-DS3 DS3 Uplink Interface Module UIM-E1 E1 Uplink Interface Module UIM-E3 E3 Uplink Interface Module UIM-T1 T1 Uplink Interface Module
chsCfgMIBObjects	1.3.6.1.4.1.8059.1.1.1.1
chsCfgParameterConfiguration	1.3.6.1.4.1.8059.1.1.1.1.1
prmCfgMultiplexerUplinkModule	1.3.6.1.4.1.8059.1.1.1.1.1.1
STR mumCfgNotes	1.3.6.1.4.1.8059.1.1.1.1.1.1.1	NtnDisplayString	read-write	The chassis system 'Notes' field is to be used as a scratchpad (i.e. chassis id or name) by the administrator. The default value is blank. The length of string must not exceed 128 alpha-numeric characters.
mumCfgTable	1.3.6.1.4.1.8059.1.1.1.1.1.1.2		not-accessible	A list of MUM200-2/2000-2 module or Mini/Micro DSLAM entries.
mumCfgEntry	1.3.6.1.4.1.8059.1.1.1.1.1.1.2.1		not-accessible	An entry containing management information applicable to a MUM200-2/MUM2000-2 module or Mini/Micro DSLAM.
INT mumCfgIndex	1.3.6.1.4.1.8059.1.1.1.1.1.1.2.1.1	INTEGER	read-only	Translates to the physical slot number that a MUM200-2/2000-2 module exists within a chassis. The Mini/Micro DSLAMs' physical location is set to 1 by default. See below, chassis type physical location(s) translation ------------ -------------------------------- IPD12000 MUM in slots 13,14 = mumCfgIndex 1,2 respecitively IPD4000 MUM in slot 5 = mumCfgIndex 1 Mini DSLAM NA = mumCfgIndex 1 Micro DSLAM NA = mumCfgIndex 1
IP mumCfgIpAddress	1.3.6.1.4.1.8059.1.1.1.1.1.1.2.1.2	IpAddress	read-write	IP Address assigned to a MUM200-2/2000-2 module or Mini/Micro DSLAM. This parameter is initially set to a default value, i.e 192.168.254.252 for a MUM200-2/2000-2 module located in slot 13 of an IPD12000, slot 5 of an IPD4000 DSLAM and a Mini/Micro DSLAM. The default value of 192.168.254.253 will be for a MUM200-2/2000-2 module located in slot 14 of an IPD12000 (duplicate IP addresses are not allowed). These default values can be modified by the user.
IP mumCfgSubnetMask	1.3.6.1.4.1.8059.1.1.1.1.1.1.2.1.3	IpAddress	read-write	The Subnet Mask assigned to a MUM200-2/2000-2 module or Mini/Micro DSLAM. This parameter is assiged by the user, the default value is 255.255.255.0.
IP mumCfgDefaultGateway	1.3.6.1.4.1.8059.1.1.1.1.1.1.2.1.4	IpAddress	read-write	The Default Gateway assigned to a MUM200-2/2000-2 module or Mini/Micro DSLAM. This value is assiged by the user, the default value is 0.0.0.0.
INT mumCfgInbandMgmt	1.3.6.1.4.1.8059.1.1.1.1.1.1.2.1.5	INTEGER	read-write	Inband management feature, when enabled [ON(1)], allows access to the DSLAM via the network against an assigned IP address, subnet mask, and default gateway.
INT mumCfgInbandMGMTVlanID	1.3.6.1.4.1.8059.1.1.1.1.1.1.2.1.6	INTEGER	read-write	The IP DSLAM supports 802.1Q Virtual LANs (VLANs). This parameter configuration applies to the inband management traffic only. It does not apply to out of band traffic received from the MGMT port. Note: for the case where the chassis type is an IPD12000 loaded with two MUMs, the setting of this parameter will affect both.
INT mumCfgInterConnection	1.3.6.1.4.1.8059.1.1.1.1.1.1.2.1.7	INTEGER	read-write	IPD12000 or IPD4000 DSLAM interconnect configuration provides the system manager the ability to daisy-chain one IP DSLAM to another so that a single router may be used for all DSLAMs in the chain.
INT mumCfgCommitChange	1.3.6.1.4.1.8059.1.1.1.1.1.1.2.1.8	INTEGER	read-write	Set to enabled(1) in order to commit the latest changes to the IP address, subnetmask, default gateway chassis parameters. This is only applicable to the SNE2040G-P and the SNE2040G-S.
mumCfgUplinkInterfaceModule	1.3.6.1.4.1.8059.1.1.1.1.1.1.3
uimCfgEthTable	1.3.6.1.4.1.8059.1.1.1.1.1.1.3.1		not-accessible	A list of ethernet Uplink Interface Module (UIM) entries.
uimCfgEthEntry	1.3.6.1.4.1.8059.1.1.1.1.1.1.3.1.1		not-accessible	An entry containing information applicable to an ethernet Uplink Interface Module (UIM).
INT uimCfgEthMumIndex	1.3.6.1.4.1.8059.1.1.1.1.1.1.3.1.1.1	INTEGER	read-only	Translates to the physical slot number that a MUM200-2/2000-2 module exists within a chassis. The Mini/Micro DSLAMs' physical location is set to 1 by default. See below, chassis type physical location(s) translation ------------ -------------------------------- IPD12000 MUM in slots 13,14 = uimCfgEthMumIndex 1,2 respecitively IPD4000 MUM in slot 5 = uimCfgEthMumIndex 1 Mini DSLAM NA = uimCfgEthMumIndex 1 Micro DSLAM NA = uimCfgEthMumIndex 1 Note: when configuring an ethernet UIM, the user must enter the index of the MUM, see above table, that corresponds with the IP address of the remote SNMP agent.
INT uimCfgEthIndex	1.3.6.1.4.1.8059.1.1.1.1.1.1.3.1.1.2	INTEGER	read-only	The physical slot used to access the UIM in the MUM200-2/2000-2 module or Mini/Micro DSLAM.
INT uimCfgEthRxTxRate	1.3.6.1.4.1.8059.1.1.1.1.1.1.3.1.1.3	INTEGER	read-write	The RxTx rate for an ethernet UIM.
INT uimCfgEthDuplex	1.3.6.1.4.1.8059.1.1.1.1.1.1.3.1.1.4	INTEGER	read-write	The current duplex setting for an ethernet UIM.
uimCfgT1Table	1.3.6.1.4.1.8059.1.1.1.1.1.1.3.2		not-accessible	A list of T1 Uplink Interface Module (UIM) entries.
uimCfgT1Entry	1.3.6.1.4.1.8059.1.1.1.1.1.1.3.2.1		not-accessible	An entry containing information applicable to a T1 Uplink Interface Module (UIM).
INT uimCfgT1MumIndex	1.3.6.1.4.1.8059.1.1.1.1.1.1.3.2.1.1	INTEGER	read-only	Translates to the physical slot number that a MUM200-2/2000-2 module exists within a chassis. The Mini/Micro DSLAMs' physical location is set to 1 by default. See below, chassis type physical location(s) translation ------------ -------------------------------- IPD12000 MUM in slots 13,14 = uimCfgT1MumIndex 1,2 respecitively IPD4000 MUM in slot 5 = uimCfgT1MumIndex 1 Mini DSLAM NA = uimCfgT1MumIndex 1 Micro DSLAM NA = uimCfgT1MumIndex 1 Note: when configuring a T1 UIM, the user must enter the index of the MUM, see above table, that corresponds with the IP address of the remote SNMP agent.
INT uimCfgT1Index	1.3.6.1.4.1.8059.1.1.1.1.1.1.3.2.1.2	INTEGER	read-only	The physical slot used to access the UIM in the MUM200-2/2000-2 module or Mini/Micro DSLAM.
INT uimCfgT1Frame	1.3.6.1.4.1.8059.1.1.1.1.1.1.3.2.1.3	INTEGER	read-write	The frame type parameter for a T1 UIM.
INT uimCfgT1LineCode	1.3.6.1.4.1.8059.1.1.1.1.1.1.3.2.1.4	INTEGER	read-write	The line code parameter for a T1 UIM.
INT uimCfgT1LineBuildout	1.3.6.1.4.1.8059.1.1.1.1.1.1.3.2.1.5	INTEGER	read-write	The line buildout parameter for a T1 UIM.
uimCfgE1Table	1.3.6.1.4.1.8059.1.1.1.1.1.1.3.3		not-accessible	A list of E1 Uplink Interface Module (UIM) entries.
uimCfgE1Entry	1.3.6.1.4.1.8059.1.1.1.1.1.1.3.3.1		not-accessible	An entry containing information applicable to an E1 Uplink Interface Module (UIM).
INT uimCfgE1MumIndex	1.3.6.1.4.1.8059.1.1.1.1.1.1.3.3.1.1	INTEGER	read-only	Translates to the physical slot number that a MUM200-2/2000-2 module exists within a chassis. The Mini/Micro DSLAMs' physical location is set to 1 by default. See below, chassis type physical location(s) translation ------------ -------------------------------- IPD12000 MUM in slots 13,14 = uimCfgE1MumIndex 1,2 respecitively IPD4000 MUM in slot 5 = uimCfgE1MumIndex 1 Mini DSLAM NA = uimCfgE1MumIndex 1 Micro DSLAM NA = uimCfgE1MumIndex 1 Note: when configuring an E1 UIM, the user must enter the index of the MUM, see above table, that corresponds with the IP address of the remote SNMP agent.
INT uimCfgE1Index	1.3.6.1.4.1.8059.1.1.1.1.1.1.3.3.1.2	INTEGER	read-only	The physical slot used to access the UIM in the MUM200-2/2000-2 module or Mini/Micro DSLAM.
INT uimCfgE1Frame	1.3.6.1.4.1.8059.1.1.1.1.1.1.3.3.1.3	INTEGER	read-write	The frame type parameter for an E1 UIM.
INT uimCfgE1LineCode	1.3.6.1.4.1.8059.1.1.1.1.1.1.3.3.1.4	INTEGER	read-write	The line code parameter for an E1 UIM.
mumSNMPConfiguration	1.3.6.1.4.1.8059.1.1.1.1.1.1.4
snmpCfgNoticeIpTable	1.3.6.1.4.1.8059.1.1.1.1.1.1.4.1		not-accessible	A list of SNMP trap notification Ip Addresses.
snmpCfgNoticeIpEntry	1.3.6.1.4.1.8059.1.1.1.1.1.1.4.1.1		not-accessible	An entry containing SNMP information applicable to a MUM200-2/MUM2000-2 module or Mini/Micro DSLAM.
INT snmpCfgNoticeIndex	1.3.6.1.4.1.8059.1.1.1.1.1.1.4.1.1.1	INTEGER	read-only	An integer value that points to one of four trap notification IP addresses.
IP snmpCfgNoticeIpAddress	1.3.6.1.4.1.8059.1.1.1.1.1.1.4.1.1.2	IpAddress	read-write	IP Address of the location or computer to which you would like trap notifications sent. The default value is 0.0.0.0 and it can be modified by the user.
INT snmpCfgAuthenticationTrapState	1.3.6.1.4.1.8059.1.1.1.1.1.1.4.2	INTEGER	read-write	Indicates whether Authentication traps should be generated. By default, this object should have the value enabled(1).
INT snmpCfgEnvironmentTrapState	1.3.6.1.4.1.8059.1.1.1.1.1.1.4.3	INTEGER	read-write	Indicates whether the fan and temperature traps should be generated. By default, this object should have the value enabled(1).
INT snmpCfgColdstartTrapState	1.3.6.1.4.1.8059.1.1.1.1.1.1.4.4	INTEGER	read-write	Indicates whether Cold Start traps should be generated. By default, this object should have the value disabled(2).
INT snmpCfgModulePortTrapState	1.3.6.1.4.1.8059.1.1.1.1.1.1.4.5	INTEGER	read-write	Indicates whether the module present/removed and link up/down traps should be generated. By default, this object should have the value disabled(2).
snmpCfgCommunity	1.3.6.1.4.1.8059.1.1.1.1.1.1.4.6
OCT comReadWriteAccess	1.3.6.1.4.1.8059.1.1.1.1.1.1.4.6.1	OCTET STRING	read-write	The community string that will allow the user read/write access to the agent. In otherwords, the user will be allowed to view and set parameter attributes. Note: since this is a hidden attribute, for security purposes, when performing a get on this OID the string that is returned will be represented by asterisk(s).
OCT comReadOnlyAccess	1.3.6.1.4.1.8059.1.1.1.1.1.1.4.6.2	OCTET STRING	read-write	The community string that will allow the user read access to the agent. In otherwords, the user will be allowed to view parameter attributes. Note: since this is a hidden attribute, for security purposes, when performing a get on this OID the string that is returned will be represented by asterisk(s).
mumCfgUniques	1.3.6.1.4.1.8059.1.1.1.1.1.1.5
INT unqEmbHttpWebsrvrState	1.3.6.1.4.1.8059.1.1.1.1.1.1.5.1	INTEGER	read-write	This configuration parameter allows the user the ability to disable, or enable, the embedded webserver. By default, this object should have the value enabled(1).
mumCfgAdvanced	1.3.6.1.4.1.8059.1.1.1.1.1.1.6
advCfgTable	1.3.6.1.4.1.8059.1.1.1.1.1.1.6.1		not-accessible	A list of the Advanced Configuration entries.
advCfgEntry	1.3.6.1.4.1.8059.1.1.1.1.1.1.6.1.1		not-accessible	An entry containing information applicable to an Advanced Configuration parameter.
INT advCfgMumIndex	1.3.6.1.4.1.8059.1.1.1.1.1.1.6.1.1.1	INTEGER	read-only	Translates to the physical slot number that a MUM200-2/2000-2 module exists within a chassis. The Mini/Micro DSLAMs' physical location is set to 1 by default. See below, chassis type physical location(s) translation ------------ -------------------------------- IPD12000 MUM in slots 13,14 = uimCfgE1MumIndex 1,2 respecitively IPD4000 MUM in slot 5 = uimCfgE1MumIndex 1 Mini DSLAM NA = uimCfgE1MumIndex 1 Micro DSLAM NA = uimCfgE1MumIndex 1 Note: when configuring an Advanced Configuration parameter, the user must enter the index of the MUM, see above table, that corresponds with the IP address of the remote SNMP agent.
INT advCfgTFTPState	1.3.6.1.4.1.8059.1.1.1.1.1.1.6.1.1.2	INTEGER	read-write	This configuration parameter allows the user the ability to disable, or enable, the TFTP server. By default, this object should have the value enabled(1).
INT advCfgTelnetState	1.3.6.1.4.1.8059.1.1.1.1.1.1.6.1.1.3	INTEGER	read-write	This configuration parameter allows the user the ability to disable, or enable, telnet. By default, this object should have the value enabled(1).
IP advCfgMgmtFltrIpStart	1.3.6.1.4.1.8059.1.1.1.1.1.1.6.1.1.4	IpAddress	read-write	The start value for the management IP filter range. This parameter is initially set to a default filter range of 0.0.0.0 - 255.255.255.255. Connection to the management system will be allowed only if the user's Ip address value falls within the defined mumCfgMgmtIpStart and mumCfgMgmtIpEnd range.
IP advCfgMgmtFltrIpEnd	1.3.6.1.4.1.8059.1.1.1.1.1.1.6.1.1.5	IpAddress	read-write	The end value for the management IP filter range. This parameter is initially set to a default filter range of 0.0.0.0 - 255.255.255.255. Connection to the management system will be allowed only if the user's Ip address value falls within the defined mumCfgMgmtIpStart and mumCfgMgmtIpEnd range.
NTN advCfgMgmtSessionTimeout	1.3.6.1.4.1.8059.1.1.1.1.1.1.6.1.1.6	NtnTimeTicks	read-write	This value defines the length of a password session in seconds. If the session has been idle for a time greater than this value, the browser will be challenged again, even if it has provided authentication credentials with the request.
mumCfgManagementPort	1.3.6.1.4.1.8059.1.1.1.1.1.1.7
mgmtPortCfgTable	1.3.6.1.4.1.8059.1.1.1.1.1.1.7.1		not-accessible	A list of the hardware platform management port entries.
mgmtPortCfgEntry	1.3.6.1.4.1.8059.1.1.1.1.1.1.7.1.1		not-accessible	An entry containing information applicable to the managment (ethernet type) port.
INT mgmtPortCfgMumIndex	1.3.6.1.4.1.8059.1.1.1.1.1.1.7.1.1.1	INTEGER	read-only	Translates to the physical slot number that a MUM200-2/2000-2 module exists within a chassis. The Mini/Micro DSLAMs' physical location is set to 1 by default. See below, chassis type physical location(s) translation ------------ -------------------------------- IPD12000 MUM in slots 13,14 = uimCfgEthMumIndex 1,2 respecitively IPD4000 MUM in slot 5 = uimCfgEthMumIndex 1 Mini DSLAM NA = uimCfgEthMumIndex 1 Micro DSLAM NA = uimCfgEthMumIndex 1 Note: when configuring a management port, the user must enter the index of the MUM, see above table, that corresponds with the IP address of the remote SNMP agent.
INT mgmtPortCfgRxTxRate	1.3.6.1.4.1.8059.1.1.1.1.1.1.7.1.1.2	INTEGER	read-write	Set the RxTx rate for an ethernet management port.
INT mgmtPortCfgDuplex	1.3.6.1.4.1.8059.1.1.1.1.1.1.7.1.1.3	INTEGER	read-write	Set the duplex setting for an ethernet management port.
INT mgmtPortCfgType	1.3.6.1.4.1.8059.1.1.1.1.1.1.7.1.1.4	INTEGER	read-write	Set the management port type as follows. By setting this port to mgmt(1), it will operate as a non-bridge mode connection. Setting it to uplink(2), this port will operate like an uplink interface module, i.e. a bridge mode connection. Note: this applies to the AuD8000-12 micro DSLAM only.

RFC description

Paradyne DSLAM and DSL equipment chassis configuration management and parameters.

Start monitoring Paradyne nTech DSLAMs with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download NTNTECH-CHASSIS-CONFIGURATION-MIB

What Is NTNTECH-CHASSIS-CONFIGURATION-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description