NTNTECH-CHASSIS-STATUS-MIB

All MIBs › NTNTECH-CHASSIS-STATUS-MIB

Organization: Paradyne Corporation

Last Updated: 2004-11-17

Category: DSL and Broadband Access

Description: Monitors chassis power, temperature, fan, and card insertion status for Paradyne nTech DSL platforms.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is NTNTECH-CHASSIS-STATUS-MIB?

NTNTECH-CHASSIS-STATUS-MIB is a Paradyne Corporation (nettonet/NTNTECH) enterprise MIB that monitors chassis-level hardware status across the Paradyne IPD12000, IPD4000, and Mini/Micro DSLAM product lines. Under chsStaMIBObjects/chsStaValues/valMultiplexerUplinkModule, it defines mumStaTable (multiplexer uplink module chassis type, fan state, MAC address, firmware revision, module type per mumStaIndex) and mumStaMgmtPortTable (management port type, link state, rate, and duplex), plus uplink interface module tables — uimStaTable, uimStaEthTable, uimStaT1Table, and uimStaE1Table — covering per-port link state and rate/duplex for Ethernet, T1, and E1 uplink modules. This gives operators direct visibility into DSLAM chassis health: fan status, module presence/type, and uplink port link state and speed/duplex settings, which is critical for diagnosing DSLAM hardware failures or degraded uplink connectivity in the field. It depends on NTNTECH-ROOT-MIB for its base OID tree and textual conventions (NtnDisplayString, NtnMacAddress), and is deployed on Paradyne DSLAM chassis and their multiplexer/uplink interface modules in DSL access networks. Field techs troubleshooting these DSLAMs often start with the NTNTECH-CHASSIS-STATUS-MIB MIB Browser view of the mumStaTable and uimSta tables.

IPNetwork Monitor allows you to monitor SNMP objects defined in NTNTECH-CHASSIS-STATUS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Paradyne IPD12000, IPD4000, and Mini/Micro DSLAM chassis (AMD8000-12, SMD2000 series, SuD2011/SuD2003/SuD2002 series, MUM200-2/MUM2000-2, and UIM uplink modules)

Monitoring Examples

An operator polls mumStaTable's mumStaFanState for chassis cooling status and uimStaEthTable's uimStaEthRxTxRate/uimStaEthDuplex for the Ethernet uplink module; a fan state showing failure combined with a T1/E1 uplink table showing an unexpected link-down state would point to a chassis overheating condition affecting uplink stability.

What Can Be Monitored

chassis fan state
multiplexer uplink module type and firmware revision
management port link state and rate/duplex
Ethernet/T1/E1 uplink module link state and rate/duplex

Imported Objects

From NTNTECH-ROOT-MIB

NtnDisplayString
NtnMacAddress
ntntechChassis	OBJECT-IDENTITY

From SNMPv2-SMI

MODULE-IDENTITY
OBJECT-TYPE

From SNMPv2-TC

TEXTUAL-CONVENTION

OIDs

OID symbolic	OID numeric	Type	Access	Description
ntntechChassisStatusMIB	1.3.6.1.4.1.8059.1.1.2			This mib module defines an SNMP API to manage the Paradyne Corporation's IPD12000, IPD4000, and Mini/Micro DSLAMs' chassis status. The interface types are described below, AMD8000-12 12-Port ADSL Mini DSLAMs With Full Rate and G.lite Operational Modes SMD2000-12, SMD2000Q-12, SMD2000G-12 12-Port SDSL Mini DSLAMs: AC and DC Versions with Cap, 2B1Q and G.SHDSL line encoding SuD2011_12T, SuD2011_12E, SuD2003_12T, SuD2003_12E 12-Port SDSL Micro DSLAMs: Cap, 2B1Q and G.SHDSL line encoding SuD2011_6T, SuD2011_6E, SuD2002_6T, SuD2002_6E 6-Port SDSL Micro DSLAMs: Cap, 2B1Q and G.SHDSL line encoding MUM200-2, MUM2000-2 Multiplexer Uplink Module with Dual Uplink Interface Module Capacity UIM-10/100 Uplink Interface Module UIM-DS3 DS3 Uplink Interface Module UIM-E1 E1 Uplink Interface Module UIM-E3 E3 Uplink Interface Module UIM-T1 T1 Uplink Interface Module
chsStaMIBObjects	1.3.6.1.4.1.8059.1.1.2.1
chsStaValues	1.3.6.1.4.1.8059.1.1.2.1.1
valMultiplexerUplinkModule	1.3.6.1.4.1.8059.1.1.2.1.1.1
INT mumStaChassisType	1.3.6.1.4.1.8059.1.1.2.1.1.1.1	INTEGER	read-only	The physical chassis type - IPD12000, IPD4000, or Mini/Micro DSLAM.
INT mumStaFanState	1.3.6.1.4.1.8059.1.1.2.1.1.1.2	INTEGER	read-only	Check the current state of the chassis fan unit. 1 = ON (all fans operational) 2 = Fault (at least one fan within the fan system has malfunctioned) 3 = Alert (all fans within the fan system have malfunctioned)
mumStaTable	1.3.6.1.4.1.8059.1.1.2.1.1.1.4		not-accessible	A list of MUM200-2/2000-2 module and Mini/Micro DSLAM entries.
mumStaEntry	1.3.6.1.4.1.8059.1.1.2.1.1.1.4.1		not-accessible	An entry containing management information applicable to a MUM200-2/MUM2000-2 module and Mini/Micro DSLAM.
INT mumStaIndex	1.3.6.1.4.1.8059.1.1.2.1.1.1.4.1.1	INTEGER	read-only	Translates to the physical slot number that a MUM200-2/2000-2 module exists within a chassis. The Mini/Micro DSLAMs' physical location is set to 1 by default. See below, chassis type physical location(s) translation ------------ -------------------------------- IPD12000 MUM in slots 13,14 = mumCfgIndex 1,2 respecitively IPD4000 MUM in slot 5 = mumCfgIndex 1 Mini DSLAM NA = mumCfgIndex 1 Micro DSLAM NA = mumCfgIndex 1
ADR mumStaMacAddress	1.3.6.1.4.1.8059.1.1.2.1.1.1.4.1.2	NtnMacAddress	read-only	The Mac Address of the MUM200-2/2000-2 module or Mini/Micro DSLAM.
OCT mumStaFirmWareRev	1.3.6.1.4.1.8059.1.1.2.1.1.1.4.1.3	OCTET STRING	read-only	The firmware revision of the MUM200-2/2000-2 module or Mini/Micro DSLAM.
INT mumStaType	1.3.6.1.4.1.8059.1.1.2.1.1.1.4.1.4	INTEGER	read-only	The physical multiplexer uplink module type.
mumStaMgmtPortTable	1.3.6.1.4.1.8059.1.1.2.1.1.1.5		not-accessible	A list of the hardware platform management port entries.
mumStaMgmtPortEntry	1.3.6.1.4.1.8059.1.1.2.1.1.1.5.1		not-accessible	An entry containing information about the state of the managment (ethernet type) port.
INT mumStaMgmtPortMumIndex	1.3.6.1.4.1.8059.1.1.2.1.1.1.5.1.1	INTEGER	read-only	Translates to the physical slot number that a MUM200-2/2000-2 module exists within a chassis. The Mini/Micro DSLAMs' physical location is set to 1 by default. See below, chassis type physical location(s) translation ------------ -------------------------------- IPD12000 MUM in slots 13,14 = mumStaMgmtPortMumIndex 1,2 respecitively IPD4000 MUM in slot 5 = mumStaMgmtPortMumIndex 1 Mini DSLAM NA = mumStaMgmtPortMumIndex 1 Micro DSLAM NA = mumStaMgmtPortMumIndex 1
INT mumStaMgmtPortType	1.3.6.1.4.1.8059.1.1.2.1.1.1.5.1.2	INTEGER	read-only	The management port type installed in the MUM200-2/2000-2 module or Mini/Micro DSLAM.
INT mumStaMgmtPortLinkState	1.3.6.1.4.1.8059.1.1.2.1.1.1.5.1.3	INTEGER	read-only	The management port Link state.
INT mumStaMgmtPortRxTxRate	1.3.6.1.4.1.8059.1.1.2.1.1.1.5.1.4	INTEGER	read-only	The RxTx rate for an ethernet management port.
INT mumStaMgmtPortDuplex	1.3.6.1.4.1.8059.1.1.2.1.1.1.5.1.5	INTEGER	read-only	The current duplex setting for an ethernet UIM.
mumStaUplinkInterfaceModule	1.3.6.1.4.1.8059.1.1.2.1.1.1.6
uimStaTable	1.3.6.1.4.1.8059.1.1.2.1.1.1.6.1		not-accessible	A list of MUM200-2/2000-2 module or Mini/Micro DSLAM Uplink Interface Module (UIM) entries.
uimStaEntry	1.3.6.1.4.1.8059.1.1.2.1.1.1.6.1.1		not-accessible	An entry containing information applicable to a MUM200-2, MUM2000-2, or Mini/Micro DSLAM Uplink Interface Module (UIM).
INT uimStaMumIndex	1.3.6.1.4.1.8059.1.1.2.1.1.1.6.1.1.1	INTEGER	read-only	Translates to the physical slot number that a MUM200-2/2000-2 module exists within a chassis. The Mini/Micro DSLAMs' physical location is set to 1 by default. See below, chassis type physical location(s) translation ------------ -------------------------------- IPD12000 MUM in slots 13,14 = uimStaMumIndex 1,2 respecitively IPD4000 MUM in slot 5 = uimStaMumIndex 1 Mini DSLAM NA = uimStaMumIndex 1 Micro DSLAM NA = uimStaMumIndex 1
INT uimStaIndex	1.3.6.1.4.1.8059.1.1.2.1.1.1.6.1.1.2	INTEGER	read-only	The physical slot used to access the UIM in the MUM200-2/2000-2 module or Mini/Micro DSLAM.
INT uimStaType	1.3.6.1.4.1.8059.1.1.2.1.1.1.6.1.1.3	INTEGER	read-only	The UIM type installed in the MUM200-2/2000-2 module or Mini/Micro DSLAM. Exception: A MUM200-2 module will represent a T1 or E1 UIM with the uimT1(2) identifier. In addition, the MUM200-2 will represent a DS3 or E3 UIM with the uimDS3(3) identifier.
INT uimStaLinkState	1.3.6.1.4.1.8059.1.1.2.1.1.1.6.1.1.4	INTEGER	read-only	The UIM Link state.
uimStaEthTable	1.3.6.1.4.1.8059.1.1.2.1.1.1.6.2		not-accessible	A list of ethernet Uplink Interface Module (UIM) entries.
uimStaEthEntry	1.3.6.1.4.1.8059.1.1.2.1.1.1.6.2.1		not-accessible	An entry containing information applicable to an ethernet Uplink Interface Module (UIM).
INT uimStaEthMumIndex	1.3.6.1.4.1.8059.1.1.2.1.1.1.6.2.1.1	INTEGER	read-only	Translates to the physical slot number that a MUM200-2/2000-2 module exists within a chassis. The Mini/Micro DSLAMs' physical location is set to 1 by default. See below, chassis type physical location(s) translation ------------ -------------------------------- IPD12000 MUM in slots 13,14 = uimStaEthMumIndex 1,2 respecitively IPD4000 MUM in slot 5 = uimStaEthMumIndex 1 Mini DSLAM NA = uimStaEthMumIndex 1 Micro DSLAM NA = uimStaEthMumIndex 1
INT uimStaEthIndex	1.3.6.1.4.1.8059.1.1.2.1.1.1.6.2.1.2	INTEGER	read-only	The physical slot used to access the UIM in the MUM200-2/2000-2 module or Mini/Micro DSLAM.
INT uimStaEthRxTxRate	1.3.6.1.4.1.8059.1.1.2.1.1.1.6.2.1.3	INTEGER	read-only	The current RxTx rate for an ethernet UIM.
INT uimStaEthDuplex	1.3.6.1.4.1.8059.1.1.2.1.1.1.6.2.1.4	INTEGER	read-only	The current duplex setting for an ethernet UIM.
uimStaT1Table	1.3.6.1.4.1.8059.1.1.2.1.1.1.6.3		not-accessible	A list of T1 Uplink Interface Module (UIM) entries.
uimStaT1Entry	1.3.6.1.4.1.8059.1.1.2.1.1.1.6.3.1		not-accessible	An entry containing information applicable to a T1 Uplink Interface Module (UIM).
INT uimStaT1MumIndex	1.3.6.1.4.1.8059.1.1.2.1.1.1.6.3.1.1	INTEGER	read-only	Translates to the physical slot number that a MUM200-2/2000-2 module exists within a chassis. The Mini/Micro DSLAMs' physical location is set to 1 by default. See below, chassis type physical location(s) translation ------------ -------------------------------- IPD12000 MUM in slots 13,14 = uimStaT1MumIndex 1,2 respecitively IPD4000 MUM in slot 5 = uimStaT1MumIndex 1 Mini DSLAM NA = uimStaT1MumIndex 1 Micro DSLAM NA = uimStaT1MumIndex 1
INT uimStaT1Index	1.3.6.1.4.1.8059.1.1.2.1.1.1.6.3.1.2	INTEGER	read-only	The physical slot used to access the UIM in the MUM200-2/2000-2 module or Mini/Micro DSLAM.
INT uimStaT1RxTxRate	1.3.6.1.4.1.8059.1.1.2.1.1.1.6.3.1.3	INTEGER	read-only	The current RxTx rate for a T1 UIM.
uimStaE1Table	1.3.6.1.4.1.8059.1.1.2.1.1.1.6.4		not-accessible	A list of E1 Uplink Interface Module (UIM) entries.
uimStaE1Entry	1.3.6.1.4.1.8059.1.1.2.1.1.1.6.4.1		not-accessible	An entry containing information applicable to an E1 Uplink Interface Module (UIM).
INT uimStaE1MumIndex	1.3.6.1.4.1.8059.1.1.2.1.1.1.6.4.1.1	INTEGER	read-only	Translates to the physical slot number that a MUM200-2/2000-2 module exists within a chassis. The Mini/Micro DSLAMs' physical location is set to 1 by default. See below, chassis type physical location(s) translation ------------ -------------------------------- IPD12000 MUM in slots 13,14 = uimStaE1MumIndex 1,2 respecitively IPD4000 MUM in slot 5 = uimStaE1MumIndex 1 Mini DSLAM NA = uimStaE1MumIndex 1 Micro DSLAM NA = uimStaE1MumIndex 1
INT uimStaE1Index	1.3.6.1.4.1.8059.1.1.2.1.1.1.6.4.1.2	INTEGER	read-only	The physical slot used to access the UIM in the MUM200-2/2000-2 module or Mini/Micro DSLAM.
INT uimStaE1RxTxRate	1.3.6.1.4.1.8059.1.1.2.1.1.1.6.4.1.3	INTEGER	read-only	The current RxTx rate for an E1 UIM.

RFC description

Paradyne DSL/DSLAM chassis status monitoring for IPD and Mini/Micro DSLAM platforms.

Start monitoring Paradyne IPD12000/IPD4000/Mini-Micro DSLAM chassis with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download NTNTECH-CHASSIS-STATUS-MIB

What Is NTNTECH-CHASSIS-STATUS-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description