QBSYS-SYSTEM-MIB

All MIBs › QBSYS-SYSTEM-MIB

Organization: Quantum Bridge Communications, Inc.

Last Updated: 2001-03-09

Category: DSL and Broadband Access, System Management

Description: Manages Quantum Bridge system-level configuration, hardware inventory, software version, and chassis management.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is QBSYS-SYSTEM-MIB?

QBSYS-SYSTEM-MIB is a vendor MIB for Quantum Bridge Technologies devices, defining system-level management objects covering chassis configuration, hardware inventory, and software version information. It exposes objects describing chassis and module hardware inventory, installed software versions, and general system configuration parameters for Quantum Bridge network equipment. Administrators often load QBSYS-SYSTEM-MIB into a MIB Browser to explore its object tree, using it to monitor hardware/software status such as chassis and module presence, hardware revision, and running software version across the device. As with many vendor system MIBs, it is organized via conformance groups and compliance statements (qbSysGroups, qbSysCompliances) and builds on standard SNMPv2-SMI/SNMPv2-CONF conventions rather than depending on unrelated external MIBs. It is deployed on Quantum Bridge chassis-based network devices where operators need visibility into system inventory and software version status via SNMP.

IPNetwork Monitor allows you to monitor SNMP objects defined in QBSYS-SYSTEM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Quantum Bridge Technologies chassis-based network device

Monitoring Examples

The sample objects available for this module, qbSysCompliances and qbSysGroups, are conformance-statement and object-group definitions rather than live data instances, so they describe which objects a compliant Quantum Bridge agent must implement rather than exposing values to poll directly. In practice, an operator would use the scalar and table objects referenced by these groups elsewhere in the MIB tree to check chassis hardware inventory and installed software version. Because only conformance objects were provided as samples here, a concrete polling scenario for specific hardware sensors can't be stated with certainty from this data alone.

What Can Be Monitored

chassis/module hardware inventory
installed software version
system configuration parameters
module presence/state

Imported Objects

From IF-MIB

InterfaceIndex
InterfaceIndexOrZero
ifIndex	OBJECT-TYPE

From QUANTUMBRIDGE-REG

qbMibs

OBJECT-IDENTITY

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Gauge32
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
TimeTicks
Unsigned32

From SNMPv2-TC

DisplayString
RowStatus
TEXTUAL-CONVENTION
TruthValue

How to Use in IPNetwork Monitor

Example using qbSysBootDiagsCode OID:

Select a Quantum Bridge Technologies chassis-based network device as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type qbSysBootDiagsCode into the Find box to locate it in the OID tree, then select it and click OK. It reports the boot-diagnostics error code from the device's last startup — 0 means no failure was detected. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is an Integer32-type OID, Value bounds is the most useful condition here — trigger an alert if the value is anything other than 0, since that indicates the device detected a boot diagnostics failure. Click Finish to create the monitor; you can adjust any parameter later.

See also: qbSysIotFileSysUpTime

OIDs

OID symbolic	OID numeric	Type	Access	Description
INT qbChassisBkplType	1.3.6.1.4.1.4323.2.2.1.1.19	INTEGER	read-only	The chassis backplane type.
INT qbChassisBulkStatsCtl	1.3.6.1.4.1.4323.2.2.1.1.21	INTEGER	read-write	The object allows to enable and disable bulk statistics collection on the OAS.
INT qbChassisNumSlots	1.3.6.1.4.1.4323.2.2.1.1.20	INTEGER	read-only	The number of slots in the chassis available for plug-in modules. QB3000 contains 7 slots, QB5000 contains 15 slots
INT qbChassisSysType	1.3.6.1.4.1.4323.2.2.1.1.18	INTEGER	read-only	The chassis system type.
U32 qbIfLocationAddr	1.3.6.1.4.1.4323.2.2.1.7.1.1.2	Unsigned32	read-only	The IOT address of the interface. If this is an IOAS's card interface, the object is set to 0.
QBS qbIfLocationPort	1.3.6.1.4.1.4323.2.2.1.7.1.1.3	QbSysPortLoc	read-only	The port number of the interface.
U32 qbIfLocationSerialNumber	1.3.6.1.4.1.4323.2.2.1.7.1.1.5	Unsigned32	read-only	If the qbIfLocationType indicates that this is an IOT, this object contains the IOT SerialNumber (as defined by qbSysIotSerialNumber) of the IOT to which this entry refers.
QBI qbIfLocationSlot	1.3.6.1.4.1.4323.2.2.1.7.1.1.1	QbIoasSlot	read-only	The slot number of the interface. If this is an IOT's interface the object is set to 0.
INT qbIfLocationType	1.3.6.1.4.1.4323.2.2.1.7.1.1.4	INTEGER	read-only	Indicates the entity to which this interface belongs: 1 - IOT, 2-IOAS.
INT qbRIPConfig	1.3.6.1.4.1.4323.2.2.1.1.11.10	INTEGER	read-write	This is a singular object in qbSysAgentGroup and is for enabling or disabling RIP Configuration system wide
INT qbSysAcoCtl	1.3.6.1.4.1.4323.2.2.1.1.8	INTEGER	read-write	The object allows to set the ACO (alarm cut off) function. When is set to clear(2) will turn off the ACO LED and supress visible alarms.Functionally it is equivalent to pushing the ACO button. Any new alarm causes the ACO button LED to illuminate. When read, this object always returns the value 'on(1)'
qbSysAgentGroup	1.3.6.1.4.1.4323.2.2.1.1.11
STR qbSysAgentReadCommunity	1.3.6.1.4.1.4323.2.2.1.1.11.5	DisplayString	read-write	This object is the read community string for the SNMP, see RFC1157.
STR qbSysAgentReadWriteCommunity	1.3.6.1.4.1.4323.2.2.1.1.11.6	DisplayString	read-write	This object is the read-write community string for the SNMP,see RFC1157. The read-write community string is required to modify this object.
IP qbSysAgentTrapDestAddr	1.3.6.1.4.1.4323.2.2.1.1.11.7.1.1	IpAddress	not-accessible	The destination address to which traps are to be transmitted.
STR qbSysAgentTrapDestComm	1.3.6.1.4.1.4323.2.2.1.1.11.7.1.3	DisplayString	read-create	Community string used for trap messages to this destination.
qbSysAgentTrapDestEntry	1.3.6.1.4.1.4323.2.2.1.1.11.7.1		not-accessible	Information relating to a set of traps and a destination address to which each trap in this set will be transmitted when it is generated. To create a new entry, a non-existent instance of qbSysAgentTrapDestAddr must be created. To remove an entry, an instance of qbSysAgentTrapDestEntryStatus of the entry must be set to destroy(6).
INT qbSysAgentTrapDestFilter	1.3.6.1.4.1.4323.2.2.1.1.11.7.1.2	INTEGER	read-create	Indicates which traps are sent to the destination address. Note that, currently,for Release 1, the only object 'all' can be set
INT qbSysAgentTrapDestPort	1.3.6.1.4.1.4323.2.2.1.1.11.7.1.5	INTEGER	read-create	The destination port number for this trap address.
ROW qbSysAgentTrapDestRowStatus	1.3.6.1.4.1.4323.2.2.1.1.11.7.1.4	RowStatus	read-create	The status of this conceptual row. This OBJECT can be set to: createAndGo(4) destroy(6) Setting this object to active(1) when its value is already active(1) is a no-op. Setting this object to createAndGo(4) causes the agent to attempt to create and commit the row based on the contents of the objects in the row. If all necessary information is present in the row and the values are acceptable to the agent, the agent will change the status to active(1). If any of the necessary objects are not available, the agent will reject the creation request. Setting this object to destroy(6) will remove the corresponding entry in this table. The following values may be read: active(1). The following objects cannot be modified while the value of this object is active(1): qbSysAgentTrapDestAddr.
qbSysAgentTrapDestTable	1.3.6.1.4.1.4323.2.2.1.1.11.7		not-accessible	This table contains information specifying which traps will be transmitted to a given destination address. The table is indexed by the destination address. Each entry in the table with a status of 'active' identifies a set of traps which, when generated, will be transmitted to the corresponding destination address listed in that entry.
NTF qbSysAlarm	1.3.6.1.4.1.4323.2.2.2.0.1			An SNMP trap definition for carrying Quantum Bridge system events. Some events have specific SNMP traps, such as linkUp or linkDown traps. (These are generally events with levels of info(3), warning(4), or fatal(5).) The events which do not have specific SNMP traps defined for them will be sent using this NOTIFICATION-TYPE if qbSysAlarmAsTrap is set to 'true(1)'.
T/F qbSysAlarmAsTrap	1.3.6.1.4.1.4323.2.2.1.3.13.1.5	TruthValue	read-only	If true, this Alarm initiates an SNMP trap.
QBA qbSysAlarmCondition	1.3.6.1.4.1.4323.2.2.1.3.6.1.6	QbAlarmCondition	read-only	The condition of the alarm.
DAT qbSysAlarmDateTime	1.3.6.1.4.1.4323.2.2.1.3.6.1.2	DateAndTimeForm	read-only	The date and time when this alarm was generated.
U32 qbSysAlarmDescrId	1.3.6.1.4.1.4323.2.2.1.3.13.1.1	Unsigned32	not-accessible	The unique alarm identifier.
qbSysAlarmEntry	1.3.6.1.4.1.4323.2.2.1.3.6.1		not-accessible	Information about a single alarm that is currently triggered.
INT qbSysAlarmHistoryClearAllCtl	1.3.6.1.4.1.4323.2.2.1.3.11	INTEGER	read-write	Setting this object to 'clear(2)' removes all entries from the qbSysAlarmHistoryTable, the qbSysEventHistoryTable and the qbSysNotificationHistoryTable. When read, this object always returns the value 'ready(1)'.
QBA qbSysAlarmHistoryCondition	1.3.6.1.4.1.4323.2.2.1.3.7.1.6	QbAlarmCondition	read-only	The condition of the alarm.
DAT qbSysAlarmHistoryDateTime	1.3.6.1.4.1.4323.2.2.1.3.7.1.2	DateAndTimeForm	read-only	The date and time when this alarm was generated.
qbSysAlarmHistoryEntry	1.3.6.1.4.1.4323.2.2.1.3.7.1		not-accessible	Information about a single alarm.
U32 qbSysAlarmHistoryId	1.3.6.1.4.1.4323.2.2.1.3.7.1.7	Unsigned32	read-only	The identifier of the alarm. This id is unique within a system. This is used to lookup the alarm description in the qbSysAlarmIdTable
U32 qbSysAlarmHistoryIndex	1.3.6.1.4.1.4323.2.2.1.3.7.1.1	Unsigned32	not-accessible	Indicates the number of the alarm. Alarms are numbered sequentially from 1 - n. A management station can keep track of the last event it uploaded and periodically GET-NEXT from there to determine if there have been any new events. This means that, as alarms are removed from the table their indices are not reused until the next reset to default configuration (which loses all stored alarms). The agent must store the 'next available alarm number' value across re-initializations of the system, resetting it to 1 only when the configuration is reset to defaults.
INT qbSysAlarmHistoryLastIndex	1.3.6.1.4.1.4323.2.2.1.3.19	INTEGER	read-only	The index of the last entry in the qbSysAlarmHistoryTable, in time-order.
I32 qbSysAlarmHistoryMaxTableSize	1.3.6.1.4.1.4323.2.2.1.3.8	Integer32	read-only	The maximum number of entries in the AlarmHistoryTable. When the number of entries gets larger than this size, older entries are discarded.
STR qbSysAlarmHistoryMsg	1.3.6.1.4.1.4323.2.2.1.3.7.1.8	DisplayString	read-only	Textual message associated with the alarm.
DAT qbSysAlarmHistoryOutFilterDateTime	1.3.6.1.4.1.4323.2.2.1.3.10	DateAndTimeForm	read-only	obsolete.
QBE qbSysAlarmHistoryOutFilterLevel	1.3.6.1.4.1.4323.2.2.1.3.9	QbEventSeverity	read-only	obsolete.
QBE qbSysAlarmHistorySeverity	1.3.6.1.4.1.4323.2.2.1.3.7.1.5	QbEventSeverity	read-only	The severity of the alarm.
QBE qbSysAlarmHistorySrvAffect	1.3.6.1.4.1.4323.2.2.1.3.7.1.4	QbEventSrvAffect	read-only	Describes whether the event was service affecting.
STR qbSysAlarmHistorySubsystem	1.3.6.1.4.1.4323.2.2.1.3.7.1.3	DisplayString	read-only	The subsystem that generated this alarm.
qbSysAlarmHistoryTable	1.3.6.1.4.1.4323.2.2.1.3.7		not-accessible	A table of alarms in the order that they were generated.
U32 qbSysAlarmId	1.3.6.1.4.1.4323.2.2.1.3.6.1.7	Unsigned32	read-only	The identifier of the alarm. This id is unique within a system. This id maps to a qbSysAlarmIdEntry. This is used to lookup the alarm description in the qbSysAlarmIdTable.
qbSysAlarmIdEntry	1.3.6.1.4.1.4323.2.2.1.3.13.1		not-accessible	Information for a particular alarm id.
STR qbSysAlarmIdName	1.3.6.1.4.1.4323.2.2.1.3.13.1.2	DisplayString	read-only	The textual name of the alarm.
QBE qbSysAlarmIdSASeverity	1.3.6.1.4.1.4323.2.2.1.3.13.1.4	QbEventSeverity	read-only	The severity of the alarm when it is Service Affecting.
QBE qbSysAlarmIdSeverity	1.3.6.1.4.1.4323.2.2.1.3.13.1.3	QbEventSeverity	read-only	The severity of the alarm.
qbSysAlarmIdTable	1.3.6.1.4.1.4323.2.2.1.3.13		not-accessible	A table of alarm information for each identifier
U32 qbSysAlarmIndex	1.3.6.1.4.1.4323.2.2.1.3.6.1.1	Unsigned32	not-accessible	The internal index into the Alarm Table. The index is incremented for each new alarm entry put into the ring. When the alarm is cleared the entry is removed from the table. On a node reset, the object is reset to 0.
STR qbSysAlarmMsg	1.3.6.1.4.1.4323.2.2.1.3.6.1.8	DisplayString	read-only	Textual message associated with the alarm.
OID qbSysAlarmResource	1.3.6.1.4.1.4323.2.2.1.3.6.1.9	OBJECT IDENTIFIER	read-only	The Resource to which this alarm corresponds. For example, if the alarm refers to Module removal, the resource would be the OID 'qbSysModuleOperStatus', including the instance ID of the Module removed.
QBE qbSysAlarmSeverity	1.3.6.1.4.1.4323.2.2.1.3.6.1.5	QbEventSeverity	read-only	The severity of the alarm.
QBE qbSysAlarmSrvAffect	1.3.6.1.4.1.4323.2.2.1.3.6.1.4	QbEventSrvAffect	read-only	The type of the alarm. Can be 2 different modes: Service affecting and nonservice affecting.
STR qbSysAlarmSubsystem	1.3.6.1.4.1.4323.2.2.1.3.6.1.3	DisplayString	read-only	The subsystem that generated this alarm.
qbSysAlarmTable	1.3.6.1.4.1.4323.2.2.1.3.6		not-accessible	A table that conatins the currently triggered alarms in the order that have not been cleared yet. The index is incremented for each new alarm entry put onto the ring. When an alarm is cleared this entry is removed from the table.
INT qbSysApsAlarmStatus	1.3.6.1.4.1.4323.2.2.1.4.2	INTEGER	read-write	Indicates whether APS alarms should be generated for this interface.
INT qbSysAutonomousStatus	1.3.6.1.4.1.4323.2.2.1.1.9	INTEGER	read-only	The object enables or disables alarms at the CLI (when a user logged in). If on, autonomous alarms will display at CLI. If off, they will not be displayed.
I32 qbSysBootDiagsCodeEx	1.3.6.1.4.1.4323.2.2.1.1.4	Integer32	read-only	An error code giving more details about a boot diagnostics failure indicated by qbSysOperStatus 'warning(1)' or 'down(2)'. The value 0 indicates no failure detected.
U32 qbSysBootImageAddress	1.3.6.1.4.1.4323.2.2.1.1.12.1.1.3	Unsigned32	read-only	Not used.
qbSysBootImageEntry	1.3.6.1.4.1.4323.2.2.1.1.12.1.1		not-accessible	Not used.
INT qbSysBootImageIndex	1.3.6.1.4.1.4323.2.2.1.1.12.1.1.1	INTEGER	not-accessible	Not used.
STR qbSysBootImageName	1.3.6.1.4.1.4323.2.2.1.1.12.1.1.2	DisplayString	read-write	Not used.
qbSysBootImageTable	1.3.6.1.4.1.4323.2.2.1.1.12.1		not-accessible	Not used.
U32 qbSysCliMsgCode	1.3.6.1.4.1.4323.2.2.1.1.11.9	Unsigned32	read-write	This object is the read-write community string for the SNMP,see RFC1157. The read-write community string is required to modify this object.
qbSysCompliance	1.3.6.1.4.1.4323.2.2.3.1.1			The compliance statement for all agents that support this MIB. A compliant agent implements all objects defined in this MIB.
qbSysCompliances	1.3.6.1.4.1.4323.2.2.3.1
DAT qbSysConfigLastWriteDateTime	1.3.6.1.4.1.4323.2.2.1.2.1	DateAndTimeForm	read-only	The last time any configuration parameter value was written to flash memory. A zero-length value indicates that no changes have been made and that the system is running using all defaults. Note that this parameter must be saved in non-volatile memory across re-initializations of the system.
IP qbSysConfigLastWriteSource	1.3.6.1.4.1.4323.2.2.1.2.2	IpAddress	read-only	The source address of the entity that made the last configuration change to the system. The value 127.0.0.1 (the loopback address) indicates the local console. This value must also be saved in non-volatile memory across re-initializations of the system.
qbSysConfigParamsGroup	1.3.6.1.4.1.4323.2.2.1.2
qbSysConfigParamsGroupInfo	1.3.6.1.4.1.4323.2.2.3.2.2			The set of all accessible objects in the Configuration Parmaeters Group in this MIB.
NTF qbSysConfigurationEvent	1.3.6.1.4.1.4323.2.2.2.0.15			the qbSysConfigurationEvent typically represents some sort of configuration or provisioning action on the system.
qbSysConformance	1.3.6.1.4.1.4323.2.2.3
DAT qbSysDateTime	1.3.6.1.4.1.4323.2.2.1.1.1	DateAndTimeForm	read-write	The current date and time of the system. Note that this can also be used to set and reset the current date and time.
IP qbSysDefaultIpRouter	1.3.6.1.4.1.4323.2.2.1.1.11.4	IpAddress	read-write	This is a machine, connected to the same subnet as the sysctl management interface, which is capable of routing IP packets
INT qbSysDefaultRouterType	1.3.6.1.4.1.4323.2.2.1.1.11.8	INTEGER	read-write	This indicates the kind of the management port associated with the default gateway.
INT qbSysDiscreteInputAdminStatus	1.3.6.1.4.1.4323.2.2.1.1.10.1.3	INTEGER	read-write	The value determines the desired administrative status of a discrete input. If enabled, the The enabled and disabled states indicate that the discrete-input is enabled or disabled respectively. The unknown state indicates that the discrete input was not configured.
qbSysDiscreteInputEntry	1.3.6.1.4.1.4323.2.2.1.1.10.1		not-accessible	Information about a single Discrete Entry.
STR qbSysDiscreteInputName	1.3.6.1.4.1.4323.2.2.1.1.10.1.2	DisplayString	read-write	The user defined discrete input name.
INT qbSysDiscreteInputState	1.3.6.1.4.1.4323.2.2.1.1.10.1.4	INTEGER	read-only	The value determines the operational status of a discrete input. The on and off states indicate that the discrete-input is enabled or disabled respectively. The unknown state indicates that the discrete input was not configured.
qbSysDiscreteInputTable	1.3.6.1.4.1.4323.2.2.1.1.10		not-accessible	A list of discrete inputs entries. This table contains information specifying discrete inputs that are configured for this system. Each entry in the table with a status of 'active' identifies a discrete input that is currently enabled.
INT qbSysDiscreteInputType	1.3.6.1.4.1.4323.2.2.1.1.10.1.1	INTEGER	read-only	The user defined type of the discrete input.
NTF qbSysEvent	1.3.6.1.4.1.4323.2.2.2.0.2			An SNMP trap definition for carrying Quantum Bridge system events. Some events have specific SNMP traps, such as linkUp or linkDown traps. (These are generally events with levels of info(3), warning(4), or fatal(5).) The events which do not have specific SNMP traps defined for them will be sent using this NOTIFICATION-TYPE if qbSysEventAsTrap is set to 'true(1)'.
T/F qbSysEventAsTrap	1.3.6.1.4.1.4323.2.2.1.3.12.1.5	TruthValue	read-only	If true, this Event initiates an SNMP Trap.
U32 qbSysEventDescrId	1.3.6.1.4.1.4323.2.2.1.3.12.1.1	Unsigned32	not-accessible	The unique event identifier.
qbSysEventGroupInfo	1.3.6.1.4.1.4323.2.2.3.2.3			The set of all accessible objects in the system events group in this MIB.
INT qbSysEventHistoryClearAllCtl	1.3.6.1.4.1.4323.2.2.1.3.5	INTEGER	read-write	Setting this object to 'clear(2)' removes all entries from the qbSysAlarmHistoryTable, the qbSysEventHistoryTable and the qbSysNotificationHistoryTable. When read, this object always returns the value 'ready(1)'.
DAT qbSysEventHistoryDateTime	1.3.6.1.4.1.4323.2.2.1.3.1.1.2	DateAndTimeForm	read-only	The date and time when this event was generated.
qbSysEventHistoryEntry	1.3.6.1.4.1.4323.2.2.1.3.1.1		not-accessible	Information about a single event.
U32 qbSysEventHistoryId	1.3.6.1.4.1.4323.2.2.1.3.1.1.6	Unsigned32	read-only	The identifier of the event. This id is unique within a system. This id maps to a qbSysEventIdEntry. It is used to lookup the event description in the qbSysEventIdTable.
U32 qbSysEventHistoryIndex	1.3.6.1.4.1.4323.2.2.1.3.1.1.1	Unsigned32	not-accessible	Indicates the number of the event. Events are numbered sequentially from 1 - n. A management station can keep track of the last event it uploaded and periodically GET-NEXT from there to determine if there have been any new events. This means that, as events are removed from the table their indices are not reused until the next reset to default configuration (which loses all stored events). The agent must store the 'next available event number' value across re-initializations of the system, resetting it to 1 only when the configuration is reset to defaults.
INT qbSysEventHistoryLastIndex	1.3.6.1.4.1.4323.2.2.1.3.20	INTEGER	read-only	The index of the last entry in the qbSysEventHistoryTable, in time-order.
I32 qbSysEventHistoryMaxTableSize	1.3.6.1.4.1.4323.2.2.1.3.2	Integer32	read-only	The maximum number of entries in the qbSysEventHistoryTable. When the number of entries gets larger than this size, older entries are discarded. The event level is considered when discarding old events because the log is full (old debug or trace messages are discarded before even older warning or fatal messages).
STR qbSysEventHistoryMsg	1.3.6.1.4.1.4323.2.2.1.3.1.1.7	DisplayString	read-only	Textual message associated with the event.
DAT qbSysEventHistoryOutFilterDateTime	1.3.6.1.4.1.4323.2.2.1.3.4	DateAndTimeForm	read-only	obsolete.
QBE qbSysEventHistoryOutFilterLevel	1.3.6.1.4.1.4323.2.2.1.3.3	QbEventSeverity	read-only	obsolete.
QBE qbSysEventHistorySeverity	1.3.6.1.4.1.4323.2.2.1.3.1.1.5	QbEventSeverity	read-only	The severity of the event.
QBE qbSysEventHistorySrvAffect	1.3.6.1.4.1.4323.2.2.1.3.1.1.4	QbEventSrvAffect	read-only	Describes whether the event was service affecting.
STR qbSysEventHistorySubsystem	1.3.6.1.4.1.4323.2.2.1.3.1.1.3	DisplayString	read-only	The subsystem that generated this event.
qbSysEventHistoryTable	1.3.6.1.4.1.4323.2.2.1.3.1		not-accessible	A table of events in the order that they were generated. An event may or may not be added to this (conceptual) table based on whether it passes all of the input filter criteria identified below. When the table is retrieved via SNMP operations, it may or may not include a specific event based on the current output filter criteria.
qbSysEventIdEntry	1.3.6.1.4.1.4323.2.2.1.3.12.1		not-accessible	Information for a particular event id.
STR qbSysEventIdName	1.3.6.1.4.1.4323.2.2.1.3.12.1.2	DisplayString	read-only	The textual name of the event.
QBE qbSysEventIdSASeverity	1.3.6.1.4.1.4323.2.2.1.3.12.1.4	QbEventSeverity	read-only	The severity of the alarm when it is Service Affecting.
QBE qbSysEventIdSeverity	1.3.6.1.4.1.4323.2.2.1.3.12.1.3	QbEventSeverity	read-only	The severity of the event.
qbSysEventIdTable	1.3.6.1.4.1.4323.2.2.1.3.12		not-accessible	A table of event information for each identifier.
qbSysEventsGroup	1.3.6.1.4.1.4323.2.2.1.3
BIT qbSysFeatureKeys	1.3.6.1.4.1.4323.2.2.1.1.14	Bits	read-only	inidcates which features of OAS software are administratively enabled on this system. If a bit is set, then the corresponding feature is enabled. Note: unlimited number of features can be enabled or disabled via this object.
qbSysFileGroup	1.3.6.1.4.1.4323.2.2.1.1.12
NTF qbSysFlashInserted	1.3.6.1.4.1.4323.2.2.2.0.10			A qbSysFlashInserted trap signifies that the agent entity has detected that a flash has been inserted into the syscon module in the IOAS.
NTF qbSysFlashRemoved	1.3.6.1.4.1.4323.2.2.2.0.11			A qbSysFlashRemoved trap signifies that the agent entity has detected that a flash card has been removed from a syscon module in the IOAS.
qbSysGeneralGroup	1.3.6.1.4.1.4323.2.2.1.1
qbSysGeneralGroupInfo	1.3.6.1.4.1.4323.2.2.3.2.1			The set of all accessible objects in the General group of this MIB.
INT qbSysGlobalHistoryLastIndex	1.3.6.1.4.1.4323.2.2.1.3.21	INTEGER	read-only	This is a currently private value that can be used to retrieve the last entry in the qbSysNotificationHistoryTable, in time-order.
qbSysGroups	1.3.6.1.4.1.4323.2.2.3.2
qbSysIfLocationEntry	1.3.6.1.4.1.4323.2.2.1.7.1.1		not-accessible	An entry in the Quantum Bridge Interface Location Table. Every row in the ifTable has a corresponding entry in this table which contains location information in iotaddr.slot.port format.
qbSysIfLocationTable	1.3.6.1.4.1.4323.2.2.1.7.1		not-accessible	The Quantum Bridge Interface location table. This table contains physical mapping information for the device interfaces.
qbSysInterfaceGroupInfo	1.3.6.1.4.1.4323.2.2.3.2.7			The set of all accessible objects in the Interfaces Group of this MIB.
qbSysInterfacesGroup	1.3.6.1.4.1.4323.2.2.1.7
NUM qbSysIoasDwsIfIndex	1.3.6.1.4.1.4323.2.2.1.6.9.1.2	InterfaceIndex	read-create	The IOT's DWS interface index. Indicates the interface index of the IOAS DWS interface to which this IOT is attached.
U32 qbSysIotAddr	1.3.6.1.4.1.4323.2.2.1.6.9.1.3	Unsigned32	read-only	A Quantum Bridge identifier for the IOT device. This value can be changed if the IOAS is reset.
INT qbSysIotAdminStatus	1.3.6.1.4.1.4323.2.2.1.6.9.1.9	INTEGER	read-create	This object, when read, returns one of the following results: enable(5): IOT is currently operational disable(6): IOT is currently disabled( range, reset, standby, maintenance, or resetToDefault mode). Setting this object to one of the acceptable values gives the following results: reset(1): resets the IOT. This is the 'software reset button' of the agent. When set to 'reset(1)', the system will reset and reload its configuration from FLASH/NVRAM. resetToDefault(2): When set to resetDefault(2), the system will delete all provisioned data for this IOT and use default setings at initialization time. For both 'reset(1)' and 'resetToDefault(2)', the default IOT software version will be used unless the set PDU contains a value for qbSysIotSwVersion, in which case it will be used. range(3): When set to 'range', the IOAS will initiate or re-initiate the ranging process for the IOT. standby(4): When set to 'standby', the IOAS will halt communication with IOT, while retaining the associated connection parameters at both the IOAS and IOT. Setting this object to any other value results in an error.
STR qbSysIotDescr	1.3.6.1.4.1.4323.2.2.1.6.9.1.4	DisplayString	read-only	A textual description of the IOT. This value includes the full name and version identification of the system's hardware type, software operating-system, and networking software.
NTF qbSysIotDiscovered	1.3.6.1.4.1.4323.2.2.2.0.6			A qbSysIotDiscovered trap signifies that the agent entity has detected that a new IOT has been discovered/provisioned in the DWS network.
INT qbSysIotDsx1LineCoding	1.3.6.1.4.1.4323.2.2.1.6.9.1.11	INTEGER	read-create	This variable mirrors the dsx1LineCoding object defined in the RFC2495. When the object is set to a new value it effects all 4 DS1 ports of the IOT. NOte: The dsx1LineCoding value effects only one DS1 port.
qbSysIotEntry	1.3.6.1.4.1.4323.2.2.1.6.9.1		not-accessible	Information about a single IOT device in the system.
STR qbSysIotFileAcceptedVersion	1.3.6.1.4.1.4323.2.2.1.6.10.1.5	DisplayString	read-only	The name of a version currently accepted as the default image on this IOT. If no image is currently accepted, this entry will be null.
INT qbSysIotFileAction	1.3.6.1.4.1.4323.2.2.1.6.10.1.9	INTEGER	read-write	This command allow a remote initiation of a file based command. Currently, by convention, if this object's value is set to 'accept', the SNMP response determines its success. If this object's value is succesfully set to 'downLoad' the application can monitor the action's progress by polling the qbSysIotFileDownLoadStatus and qbSysIotFileErrorMsg objects. DownLoadAbort ends the current download.
STR qbSysIotFileAvailableVersion1	1.3.6.1.4.1.4323.2.2.1.6.10.1.2	DisplayString	read-only	The name of a version currently available on this IOT in the first FLASH region.
STR qbSysIotFileAvailableVersion2	1.3.6.1.4.1.4323.2.2.1.6.10.1.3	DisplayString	read-only	The name of a version currently running on this IOT in the second FLASH region.
INT qbSysIotFileDownLoadStatus	1.3.6.1.4.1.4323.2.2.1.6.10.1.10	INTEGER	read-only	The Status of the current download.
STR qbSysIotFileDownLoadVersion	1.3.6.1.4.1.4323.2.2.1.6.10.1.6	DisplayString	read-write	The name of a version of a file that the agent should attempt to download the next time qbSysIotFileAction is set to download.
qbSysIotFileEntry	1.3.6.1.4.1.4323.2.2.1.6.10.1		not-accessible	Information about files on a single IOT.
STR qbSysIotFileErrorMsg	1.3.6.1.4.1.4323.2.2.1.6.10.1.11	DisplayString	read-only	The error message, if any, pertaining to the current download.
TIK qbSysIotFileLastModification	1.3.6.1.4.1.4323.2.2.1.6.10.1.8	TimeTicks	read-only	The value of sysUpTime entry was last modified.
STR qbSysIotFileRunningVersion	1.3.6.1.4.1.4323.2.2.1.6.10.1.4	DisplayString	read-only	The name of the version currently running on this IOT.
U32 qbSysIotFileSerialNumber	1.3.6.1.4.1.4323.2.2.1.6.10.1.1	Unsigned32	not-accessible	The IOT serial number that these files should be associated with.
TIK qbSysIotFileSysUpTimeEx	1.3.6.1.4.1.4323.2.2.1.6.10.1.7	TimeTicks	read-only	The value of time since this IOT was initialized.
qbSysIotFileTable	1.3.6.1.4.1.4323.2.2.1.6.10		not-accessible	.
qbSysIotGroup	1.3.6.1.4.1.4323.2.2.1.6
qbSysIotGroupInfo	1.3.6.1.4.1.4323.2.2.3.2.6			The set of all accessible objects in the Intelligent Terminal Group of this MIB.
STR qbSysIotHwVersion	1.3.6.1.4.1.4323.2.2.1.6.9.1.8	DisplayString	read-only	The hardware version of the module.
STR qbSysIotLocation	1.3.6.1.4.1.4323.2.2.1.6.9.1.6	DisplayString	read-only	The physical location of the IOT. Note that, currently, this object readonly
NTF qbSysIotLos	1.3.6.1.4.1.4323.2.2.2.0.8			A qbSysIotOutOfService trap signifies that the agent entity has detected that an IOT has LOS condition.
STR qbSysIotManufSerialNum	1.3.6.1.4.1.4323.2.2.1.6.9.1.14	DisplayString	read-only	The IOT manufecturing serial number string.
STR qbSysIotName	1.3.6.1.4.1.4323.2.2.1.6.9.1.5	DisplayString	read-create	An administratively-assigned name for this IOT.
INT qbSysIotNumSlots	1.3.6.1.4.1.4323.2.2.1.6.9.1.19	INTEGER	read-only	The number of slots in the IOT chassis available for plug-in modules. QB616 contains 3 slots, all other IOT return 0
INT qbSysIotOperStatus	1.3.6.1.4.1.4323.2.2.1.6.9.1.10	INTEGER	read-only	This is the operational IOT status.
STR qbSysIotProductName	1.3.6.1.4.1.4323.2.2.1.6.9.1.16	DisplayString	read-only	An product name for this IOT.
NTF qbSysIotRemoved	1.3.6.1.4.1.4323.2.2.2.0.7			A qbSysIotRemoved trap signifies that the agent entity has detected that an IOT has been removed from the DWS network.
U32 qbSysIotRollSerialNumber	1.3.6.1.4.1.4323.2.2.1.6.9.1.18	Unsigned32	read-create	This object when reads, returns the serial number of the selected IOT(the same as qbSysIotSerialNumber). When the object is set (the serial number must be be different) the agent ralls all existing configuration from the old serial number to the serial number. As a result of this, this row is deleted and a new row is created in the table.
ROW qbSysIotRowStatus	1.3.6.1.4.1.4323.2.2.1.6.9.1.13	RowStatus	read-create	The status of this conceptual row. This OBJECT can be set to: createAndGo(4) destroy(6) Setting this object to active(1) when its value is already active(1) is a no-op. Setting this object to createAndGo(4) causes the agent to attempt to create and commit the row based on the contents of the objects in the row. If all necessary information is present in the row and the values are acceptable to the agent, the agent will change the status to active(1). If any of the necessary objects are not available, the agent will reject the creation request. Setting this object to destroy(6) will remove the corresponding entry in this table. The following values may be read: active(1).
U32 qbSysIotSerialNumber	1.3.6.1.4.1.4323.2.2.1.6.9.1.1	Unsigned32	not-accessible	The IOT serial number.
STR qbSysIotSerialStr	1.3.6.1.4.1.4323.2.2.1.6.9.1.12	DisplayString	read-create	This string has the following format for old IOTs(YYWK-PC-XXXXXX) where yy - year, wk - week of the year, and xxxxxx - serial number. For new IOT models the FSAN serial string has the following format (QMBGXXXXXXXX) where XXXXXXXX - a unique hexedecimal serial number(e.g.1F338BE3).
INT qbSysIotSignalFmt	1.3.6.1.4.1.4323.2.2.1.6.9.1.17	INTEGER	read-create	The IOT signal format type.
STR qbSysIotSwVersion	1.3.6.1.4.1.4323.2.2.1.6.9.1.7	DisplayString	read-create	When in the same set pdu as qbSysIotAdminStatus, this object indicates the version of software that the IOT will boot from if qbSysIotAdminStatus indicates a reset. If this object is not set, the default image will be used. When read, this value returns a null string. Note that the running IOT software version can be retrieved from the qbSysIotFileTable entry described below.
qbSysIotTable	1.3.6.1.4.1.4323.2.2.1.6.9		not-accessible	A table of IOT devices in the system.
QBI qbSysIotType	1.3.6.1.4.1.4323.2.2.1.6.9.1.15	QbIotType	read-create	The IOT type.
IP qbSysMgmtIpAddr	1.3.6.1.4.1.4323.2.2.1.1.11.2	IpAddress	read-write	Active IP Address for SNMP Management of this chassis. This is the IP address used for network mangement.
IP qbSysMgmtIpMask	1.3.6.1.4.1.4323.2.2.1.1.11.3	IpAddress	read-write	This is the IP network mask associated with the Management interface.
qbSysMIB	1.3.6.1.4.1.4323.2.2			This module defines objects for the management of Quantum Bridge devices.
INT qbSysModuleAdminStatus	1.3.6.1.4.1.4323.2.2.1.4.1.1.5	INTEGER	read-write	This object, when read, returns one of the following results: other(1): module permanently enabled enable(3): module currently enabled disable(4): module currently disabled clearslot(5): used to clear slot Setting this object to one of the acceptable values gives the following results: other(1): gives an error reset(2): resets the module enable(3): if the module status is configurable, enables the module, else gives error disable(4): if the module status is configurable, disables the module, else gives error Setting this object to any other value results in an error. Note that, currently, this object 'readonly'
qbSysModuleApsEntry	1.3.6.1.4.1.4323.2.2.1.4.3.1		not-accessible	Entry contains module APS information.
QBA qbSysModuleApsGroupAdminMode	1.3.6.1.4.1.4323.2.2.1.4.3.1.1	QbApsGroupMode	read-write	This object is used to set the protection mode for a given slot. Note: Only main-a, main-b, au-1, au-2, au-3, au-4, au-5 au-6, au-7 or au-8 may be selected for. this object. Only slots containing SONET interfaces are valid.
INT qbSysModuleApsGroupOperMode	1.3.6.1.4.1.4323.2.2.1.4.3.1.2	INTEGER	read-only	This object indicates a protection mode of a given slot within an SPG group.
TIM qbSysModuleApsLastSwitchoverTime	1.3.6.1.4.1.4323.2.2.1.4.3.1.5	TimeStamp	read-only	The value of sysUpTime at the time of the last switchover of the a given card. The value is zero if there has not been a switchover since agent initialization.
QBA qbSysModuleApsSwitchAdminMode	1.3.6.1.4.1.4323.2.2.1.4.3.1.3	QbApsSwitchMode	read-write	This object is used to allow a user execution APS switch commands for a given slot.
INT qbSysModuleApsSwitchOperMode	1.3.6.1.4.1.4323.2.2.1.4.3.1.4	INTEGER	read-only	The object indicates the current highest priority switching state of the slot. noop - this value should be returned by a read request when no switch command has been written to a given slot since initialization. sf - signal failure on the slot sd - signal degrade on the slot fail - equipment fail or removed
qbSysModuleApsTable	1.3.6.1.4.1.4323.2.2.1.4.3		not-accessible	This tables lists OAS's modules. The number of entries is equals the number of cards in an OAS chassis.
NTF qbSysModuleDown	1.3.6.1.4.1.4323.2.2.2.0.3			A qbSysModuleDown trap signifies that the agent entity has detected that the qbSysModuleStatus object in this MIB has transitioned from the ok(2) state to one of another state.
qbSysModuleEntry	1.3.6.1.4.1.4323.2.2.1.4.1.1		not-accessible	Entry containing information about one module in the chassis.
STR qbSysModuleEqId	1.3.6.1.4.1.4323.2.2.1.4.1.1.11	DisplayString	read-only	The manufacturer's equipment identifier.
qbSysModuleGroup	1.3.6.1.4.1.4323.2.2.1.4
qbSysModuleGroupInfo	1.3.6.1.4.1.4323.2.2.3.2.4			The set of all accessible objects in the Module Group of this MIB.
STR qbSysModuleHwVersion	1.3.6.1.4.1.4323.2.2.1.4.1.1.12	DisplayString	read-only	The hardware version of the module.
NTF qbSysModuleInserted	1.3.6.1.4.1.4323.2.2.2.0.4			A qbSysModuleInserted trap signifies that the agent entity has detected that a board has been inserted into a particular slot in the IOAS.
TIM qbSysModuleLastSwitchoverTime	1.3.6.1.4.1.4323.2.2.1.4.1.1.15	TimeStamp	read-only	The value of sysUpTime at the last switchover of the switch cards. The value is zero if there has been no switchover since agent initialization.
OCT qbSysModuleLedStatus	1.3.6.1.4.1.4323.2.2.1.4.1.1.17	OCTET STRING	read-only	Led OCTET String A series of bytes containing status information about each of leds in the module. For every led two bytes are allocated. The first byte indicates the led type, the second byte indicates the led state (on/off). Therefore byte string size is different depending of the module types. The leds of modules as follows: SYSCON: 1 CR(0) 2 MJ(1) 3 MN(2) 4 MNTC(3) 5 Fault(4) 6 ACO(5) SWITCH/SWPROC - 1 FAULT(1) 2 ACTIVE(2) WAN/MOC12 1 FAULT(0) 2 ACTIVE(1) 3 LOS(2) AU-1 1 FAULT(0) 2 ACTIVE(1) 3 LOS(2)
STR qbSysModuleModel	1.3.6.1.4.1.4323.2.2.1.4.1.1.9	DisplayString	read-only	The manufacturer's model part number for the module.
STR qbSysModuleName	1.3.6.1.4.1.4323.2.2.1.4.1.1.3	DisplayString	read-write	A descriptive string used by network administrator to name the module.
INT qbSysModuleNumPorts	1.3.6.1.4.1.4323.2.2.1.4.1.1.7	INTEGER	read-only	The number of ports supported by the module.
INT qbSysModuleOperStatus	1.3.6.1.4.1.4323.2.2.1.4.1.1.4	INTEGER	read-only	The operational status of the module. If the status is not ok, the value of the moduleTestResult gives more detailed information about the module's failure condition(s).
OCT qbSysModulePortStatus	1.3.6.1.4.1.4323.2.2.1.4.1.1.8	OCTET STRING	read-only	A series of bytes containing status information about the module and each of the ports in the module. The first byte contains the status of the module (same value as moduleStatus), and subsequent bytes contain statuses for the first through last ports on the module (same value as ifOperStatus).
STR qbSysModuleProductName	1.3.6.1.4.1.4323.2.2.1.4.1.1.18	DisplayString	read-only	A descriptive string used by vendor to name the module.
PRO qbSysModuleProtectionMode	1.3.6.1.4.1.4323.2.2.1.4.1.1.14	ProtectionMode	read-write	Protection mode of a module.
NTF qbSysModuleRemoved	1.3.6.1.4.1.4323.2.2.2.0.5			A qbSysModuleRemoved trap signifies that the agent entity has detected that a board has been removed from a particular slot in the IOAS.
STR qbSysModuleSerialNum	1.3.6.1.4.1.4323.2.2.1.4.1.1.10	DisplayString	read-only	The manufacturer's serial number for the module.
INT qbSysModuleSlot	1.3.6.1.4.1.4323.2.2.1.4.1.1.1	INTEGER	read-only	This value is determined by the OAS slot number where the module is located. Valid range is from 1 to 15 for QB5000 and from 1 to 7 for QB3000.
NTF qbSysModuleSwitchover	1.3.6.1.4.1.4323.2.2.2.0.9			This notification is generated when the value of qbSysModuleStandbyStatus changes from active(1) to either standby(2) or notProtected(3) or notPresent(4). The notification is also generated when the value of qbSysModuleStandbyStatus changes from standby(2) to active(1). The varbind indicates the current mode of the affected card.
INT qbSysModuleSwitchoverReason	1.3.6.1.4.1.4323.2.2.1.4.1.1.16	INTEGER	read-only	The reason for the last switch card switchover. The value is none(1) if there has been no switchover since agent initialization.
STR qbSysModuleSwVersion	1.3.6.1.4.1.4323.2.2.1.4.1.1.13	DisplayString	read-only	The software version of the module.
qbSysModuleTable	1.3.6.1.4.1.4323.2.2.1.4.1		not-accessible	A list of IOAS's cards. The number of entries is the number of cards in the IOAS chassis.
INT qbSysModuleTestLeds	1.3.6.1.4.1.4323.2.2.1.4.1.1.19	INTEGER	read-write	This object tests the module LEDs. If the object is read, it should return ready. Setting the value test will initiate the LED test for this card.
INT qbSysModuleTestResult	1.3.6.1.4.1.4323.2.2.1.4.1.1.6	INTEGER	read-only	The result of the module's self test. A zero indicates that the module passed all tests. Bits set in the result indicate error conditions.
INT qbSysModuleType	1.3.6.1.4.1.4323.2.2.1.4.1.1.2	INTEGER	read-only	The module type.
QBN qbSysNotificationHistoryAction	1.3.6.1.4.1.4323.2.2.1.3.14.1.5	QbNotificationAction	read-only	The resource action that caused this event.
QBN qbSysNotificationHistoryAlarmCondition	1.3.6.1.4.1.4323.2.2.1.3.14.1.9	QbNotificationAlarmCondition	read-only	The alarm condition of the Notification.
INT qbSysNotificationHistoryClearAllCtl	1.3.6.1.4.1.4323.2.2.1.3.18	INTEGER	read-write	obsolete.
U32 qbSysNotificationHistoryCookie	1.3.6.1.4.1.4323.2.2.1.3.14.1.7	Unsigned32	read-only	This cookie is used to store augmenting information pertaining to this Notification. By convention, the cookie contains the value of the object 'pointed' to by qbSysNotificationHistoryResource. If this value is not syntactically consistent with the qbSysNotificationHistoryResource, then it is by convention set to '0'.
DAT qbSysNotificationHistoryDateTime	1.3.6.1.4.1.4323.2.2.1.3.14.1.8	DateAndTimeForm	read-only	The time when this Notification was generated.
qbSysNotificationHistoryEntry	1.3.6.1.4.1.4323.2.2.1.3.14.1		not-accessible	Information about a single Notification.
U32 qbSysNotificationHistoryIndex	1.3.6.1.4.1.4323.2.2.1.3.14.1.1	Unsigned32	not-accessible	A unique number of the entry.
I32 qbSysNotificationHistoryMaxTableSize	1.3.6.1.4.1.4323.2.2.1.3.15	Integer32	read-only	The maximum number of entries in the NotificationHistoryTable. When the number of entries gets larger than this size, older entries are discarded.
DAT qbSysNotificationHistoryOutFilterDateTime	1.3.6.1.4.1.4323.2.2.1.3.17	DateAndTimeForm	read-write	obsolete.
QBE qbSysNotificationHistoryOutFilterLevel	1.3.6.1.4.1.4323.2.2.1.3.16	QbEventSeverity	read-only	obsolete.
OID qbSysNotificationHistoryResource	1.3.6.1.4.1.4323.2.2.1.3.14.1.6	OBJECT IDENTIFIER	read-only	The Resource to which this entry corresponds. For example, if the Notication refers to Module removal, the resource would be the OID 'qbSysModuleOperStatus', including the instance ID of the Module removed.
QBE qbSysNotificationHistoryServiceAffecting	1.3.6.1.4.1.4323.2.2.1.3.14.1.10	QbEventSrvAffect	read-only	If this Notification's QbNotificationType is an alarm or event, then this obejct identifies whether the corresponding alarm or event was service affecting. Otherwise, it is nonServiceAffecting.
qbSysNotificationHistoryTable	1.3.6.1.4.1.4323.2.2.1.3.14		not-accessible	A table of Notifications in the order that they were generated. Currently these Notifications include qbSysUnsolicitedEvents and qbSysConfigurationEvents.
QBN qbSysNotificationHistoryType	1.3.6.1.4.1.4323.2.2.1.3.14.1.3	QbNotificationType	read-only	The type of Resource Event this notification represents. If this is a qbAlarm Notification, then the qbSysNotificationHistoryId refers to an entry in the qbSysAlarmIdTable. If it is of type qbEvent, the qbSysNotificationHistoryId refers to an entry in the qbSysEventIdTable.
U32 qbSysNotificationHistoryTypeId	1.3.6.1.4.1.4323.2.2.1.3.14.1.4	Unsigned32	read-only	This Id can optioanlly refer to a structure that augments the Notification.
OID qbSysNotificationOID	1.3.6.1.4.1.4323.2.2.1.3.14.1.2	OBJECT IDENTIFIER	read-only	Indicates OID of the Notifcation that this entry refers. Though primarily intended to be the qbSysUnsolicitedEvent or qbSysConfigurationEvent OID, this value could also be another NOTIFICATION OID, for example a standard SNMP NOTIFICATION.
qbSysNotificationPrefix	1.3.6.1.4.1.4323.2.2.2.0
qbSysNotifications	1.3.6.1.4.1.4323.2.2.2
qbSysObjects	1.3.6.1.4.1.4323.2.2.1
INT qbSysOperStatus	1.3.6.1.4.1.4323.2.2.1.1.2	INTEGER	read-only	The current operational status of the Quantum Bridge IOAS System as a whole. A value 'unknown(1)' indicates that the current state of the system could not be determined. The value 'running(2)' indicates that the system is up and running and that no unusual error conditions have been detected. The 'warning(3)' state indicates that the agent has been informed of an unusual error condition by the operational software (e.g., a device driver) but that the system is still 'operational'. (The qbSysBootDiagsCode object may provide more information.) A value of 'testing(4)', indicates that the system is not available for use because it is in the testing state.
INT qbSysPort	1.3.6.1.4.1.4323.2.2.1.5.1.1.1	INTEGER	read-only	A port number that uniquely identifies this port within a card. The value is determined by the location of the port in the module. Valid entries are 1 to the value of moduleNumPorts for this module.
INT qbSysPortBwSharing	1.3.6.1.4.1.4323.2.2.1.1.15	INTEGER	read-write	This object shows and controls the bandwidth allocation between Au-1 and au-2. If it is set to 622, then there is no port sharing enabled between the ports. Any other setting will enable port sharing, and the 622 Mbis/sec of bandwidth is split between the 2 ports. Note. If protection is being used, then the bandwidth should be set to 622.
qbSysPortEntry	1.3.6.1.4.1.4323.2.2.1.5.1.1		not-accessible	Entry containing information for a particular port in a module.
qbSysPortGroup	1.3.6.1.4.1.4323.2.2.1.5
qbSysPortGroupInfo	1.3.6.1.4.1.4323.2.2.3.2.5			The set of all accessible objects in the Port Group of this MIB.
U32 qbSysPortIfIndex	1.3.6.1.4.1.4323.2.2.1.5.1.1.5	Unsigned32	read-only	The value of the instance of the ifIndex object, defined in MIB-II, for the interface corresponding to this port.
INT qbSysPortLoopbackConfig	1.3.6.1.4.1.4323.2.2.1.5.1.1.6	INTEGER	read-write	The current loopback state of the port. The values mean: unLoop Not in the loopback state. A device that is not capable of performing a loopback on this interface will always return this value. facility The received signal at this interface is looped back out through the corresponding transmitter in the return direction.This test can be performed only on main card interfaces. terminalLoop The signal that is about to be transmitted is connected to the associated incoming receiver. This test can be performed on main and dws interfaces.
STR qbSysPortName	1.3.6.1.4.1.4323.2.2.1.5.1.1.2	DisplayString	read-only	A descriptive string used by the network administrator to name the port. This string has the same value as the ifName object
INT qbSysPortOperStatus	1.3.6.1.4.1.4323.2.2.1.5.1.1.4	INTEGER	read-only	The current operational status of the port.
qbSysPortTable	1.3.6.1.4.1.4323.2.2.1.5.1		not-accessible	A list of port entries. The number of entries is determined by the number of modules in the chassis and the number of ports in each module.
INT qbSysPortType	1.3.6.1.4.1.4323.2.2.1.5.1.1.3	INTEGER	read-only	The physical layer port type.
INT qbSysPowerSupplyType	1.3.6.1.4.1.4323.2.2.1.1.7	INTEGER	read-only	The type of power supply.
NTF qbSysProvChanges	1.3.6.1.4.1.4323.2.2.2.0.12			A qbSysConfigChanges trap that the agent entity has detected that provisoning changes were detected. The varbind indicates that type of changes occured for a given system. Note: Release 2
INT qbSysProvType	1.3.6.1.4.1.4323.2.2.1.2.3	INTEGER	read-only	The type of provisioning that occured to the system. provIot indicates that an IOT added/removed, or changed state. provConn indicates that a connection added/removed, or changed state.
INT qbSysResetCtl	1.3.6.1.4.1.4323.2.2.1.1.3	INTEGER	read-write	This is the 'software reset button' of the agent. When read, this object always returns the value 'ready(1)'. When set to 'reset(2)', the system will reset and reload its configuration from FLASH/NVRAM. Note that when this object is set, the object qbSysResetVersion will be used to get the software version to be booted from.
STR qbSysResetVersion	1.3.6.1.4.1.4323.2.2.1.1.13	DisplayString	read-write	The version used by the system controller when remotely reset.
STR qbSysRunningImageVersion	1.3.6.1.4.1.4323.2.2.1.1.6	DisplayString	read-only	The running image version.
U32 qbSysSnmpRevision	1.3.6.1.4.1.4323.2.2.1.1.11.1	Unsigned32	read-only	The revision number of the SNMP agent implementation. The first two bytes indicate major revision number, the second two bytes indicate the minor revision number
T/F qbSysSwAccepted	1.3.6.1.4.1.4323.2.2.1.1.17	TruthValue	read-write	if true, the software in the switch is accepted.
INT qbSysTestLeds	1.3.6.1.4.1.4323.2.2.1.1.16	INTEGER	read-write	This object tests the system LEDs. If the object is read it should return ready. Setting the value test will initiate the LED test.
QBS qbSysTransferDest	1.3.6.1.4.1.4323.2.2.1.1.12.2.1.4	QbStorageType	read-create	Not used.
STR qbSysTransferDestName	1.3.6.1.4.1.4323.2.2.1.1.12.2.1.5	DisplayString	read-create	Not used.
qbSysTransferEntry	1.3.6.1.4.1.4323.2.2.1.1.12.2.1		not-accessible	Not used.
U32 qbSysTransferIndex	1.3.6.1.4.1.4323.2.2.1.1.12.2.1.1	Unsigned32	not-accessible	Not used.
U32 qbSysTransferIot	1.3.6.1.4.1.4323.2.2.1.1.12.2.1.7	Unsigned32	read-create	not used.
INT qbSysTransferOperProgress	1.3.6.1.4.1.4323.2.2.1.1.12.2.1.9	INTEGER	read-only	notused.
QBT qbSysTransferOperStatus	1.3.6.1.4.1.4323.2.2.1.1.12.2.1.8	QbTransferStatus	read-only	Not used.
ROW qbSysTransferRowStatus	1.3.6.1.4.1.4323.2.2.1.1.12.2.1.10	RowStatus	read-create	not used.
IP qbSysTransferServerAddr	1.3.6.1.4.1.4323.2.2.1.1.12.2.1.6	IpAddress	read-create	Not used.
QBS qbSysTransferSrc	1.3.6.1.4.1.4323.2.2.1.1.12.2.1.2	QbStorageType	read-create	Not used.
STR qbSysTransferSrcName	1.3.6.1.4.1.4323.2.2.1.1.12.2.1.3	DisplayString	read-create	Not used.
qbSysTransferTable	1.3.6.1.4.1.4323.2.2.1.1.12.2		not-accessible	Not used.
NTF qbSysUnsolicitedEvent	1.3.6.1.4.1.4323.2.2.2.0.14			The qbSysUnsolicited Event. Unsolicited Events typeically are fault or discovery events such as resource added or removed or alarm information.
INT qbSysWatchdogUpdate	1.3.6.1.4.1.4323.2.2.1.1.5	INTEGER	read-write	The number of seconds between watchdog timer updates. A watch dog reset will occur if the timer is not updated within one cycle. A value of 0 disables the watchdog timeout. The valid range of a functioning update is 1-60 seconds.
NTF qbWanRxLos	1.3.6.1.4.1.4323.2.2.2.0.13			A qbDwsRxLos trap indicates Loss of Signal by the WAN/Sonet card receiver. The trap is generated by a WAN card when a WAN card receiver problem is detected. The trap contains the WAN port interface index.

RFC description

Vendor-specific MIB for QBiS system management covering general system properties and operational status.

Start monitoring Quantum Bridge Technologies chassis-based network device (system inventory/software version) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download QBSYS-SYSTEM-MIB