HUAWEI-NGADSL-LINE-MIB

All MIBs › HUAWEI-NGADSL-LINE-MIB

Organization: Huawei Technologies Co.,Ltd.

Last Updated: 2012-07-20

Category: DSL and Broadband, Domain: DSL, Vendor: Huawei

Description: Huawei Next Generation ADSL line MIB for monitoring ADSL2/ADSL2+ line parameters, performance, and alarm thresholds.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HUAWEI-NGADSL-LINE-MIB?

HUAWEI-NGADSL-LINE-MIB is a Huawei broadband-access MIB that extends the IETF's RFC 4706 ADSL2-LINE MIB to cover Next-Generation ADSL (ADSL2/ADSL2+) line cards on Huawei access equipment. It exposes line-level configuration, physical-layer performance statistics, and alarm-threshold data for each subscriber's DSL line. Its monitoring purpose is squarely hardware/physical-layer health: tracking synchronized upstream/downstream rate, signal-to-noise margin, line attenuation, and error-second counts lets an operator detect a degrading copper line, crosstalk, or an intermittent sync loss before the subscriber experiences a full outage. It is explicitly built as an extension of the standard RFC 4706 ADSL2-LINE MIB rather than a wholly independent design. It is deployed on Huawei DSLAM/MSAN broadband access nodes serving fixed-line ADSL2/ADSL2+ subscribers. Engineers can download the HUAWEI-NGADSL-LINE-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in HUAWEI-NGADSL-LINE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Huawei DSLAM/MSAN broadband access equipment

Monitoring Examples

No sample object names were provided for this module, so specific leaf names cannot be cited, but its extension of RFC 4706 implies tables analogous to adsl2LineTable and adsl2PerfDataTable scoped per subscriber line. An operator would poll such a line's configuration and performance data to track synchronized upstream/downstream rate and signal-to-noise margin. A rising error-second count or a falling noise margin on one line, while neighboring lines stay stable, points to copper degradation or crosstalk affecting that specific subscriber's connection.

What Can Be Monitored

line sync rate (upstream/downstream)
signal-to-noise margin
line attenuation
error-second counters
line up/down status
alarm threshold state

Imported Objects

From ADSL2-LINE-MIB

adsl2	OBJECT-IDENTITY
adsl2ChAlarmConfProfileEntry	OBJECT-TYPE
adsl2ChAlarmConfProfileName	OBJECT-TYPE
adsl2ChConfProfProfileName	OBJECT-TYPE
adsl2ChStatusActDataRate	OBJECT-TYPE
adsl2ChStatusChannelNum	OBJECT-TYPE
adsl2ChStatusUnit	OBJECT-TYPE
adsl2ChannelStatusEntry	OBJECT-TYPE
adsl2LConfProfProfileName	OBJECT-TYPE
adsl2LineAlarmConfProfileName	OBJECT-TYPE
adsl2LineCmndConfLdsfFailReason	OBJECT-TYPE
adsl2LineConfProfEntry	OBJECT-TYPE
adsl2LineEntry	OBJECT-TYPE
adsl2PMChCurrEntry	OBJECT-TYPE
adsl2PMChCurrUnit	OBJECT-TYPE
adsl2PMChHist15MInterval	OBJECT-TYPE
adsl2PMChHist15MUnit	OBJECT-TYPE
adsl2PMChHist1DInterval	OBJECT-TYPE
adsl2PMChHist1DUnit	OBJECT-TYPE
adsl2PMLCurrUnit	OBJECT-TYPE
adsl2PMLHist15MInterval	OBJECT-TYPE
adsl2PMLHist15MUnit	OBJECT-TYPE
adsl2PMLHist1DInterval	OBJECT-TYPE
adsl2PMLHist1DUnit	OBJECT-TYPE
adsl2PMLHistInit15MInterval	OBJECT-TYPE
adsl2PMLHistinit1DInterval	OBJECT-TYPE
adsl2PMLineCurrEntry	OBJECT-TYPE
adsl2PMLineCurrInitEntry	OBJECT-TYPE
adsl2SCStatusDirection	OBJECT-TYPE
adsl2SCStatusEntry	OBJECT-TYPE

From HC-PerfHist-TC-MIB

HCPerfIntervalThreshold
HCPerfTimeElapsed

From HUAWEI-DEVICE-MIB

hwFrameIndex	OBJECT-TYPE
hwPortIndex	OBJECT-TYPE
hwPortOperStatus	OBJECT-TYPE
hwPortPrimaryStatus
hwPortSecondaryStatus
hwSlotIndex	OBJECT-TYPE

From HUAWEI-MIB

huaweiUtility

OBJECT-IDENTITY

From IF-MIB

ifIndex

OBJECT-TYPE

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Gauge32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DateAndTime
TEXTUAL-CONVENTION

OIDs

OID symbolic	OID numeric	Type	Access	Description
U32 adsl2LineStatusCodingGainDs	1.3.6.1.2.1.10.238.1.1.1.1.65535	Unsigned32	read-only	The actual value of Coding gain upstream parameter,it ranges from 0 to 16. Unit: 0.5 dB
U32 adsl2LineStatusCodingGainUs	1.3.6.1.2.1.10.238.1.1.1.1.65536	Unsigned32	read-only	The actual value of Coding gain downstream parameter,it ranges from 0 to 16. Unit: 0.5 dB
U32 adsl2LineStatusPcbDs	1.3.6.1.2.1.10.238.1.1.1.1.65537	Unsigned32	read-only	Indicates Power Cut-back on downstream direction. It ranges from 0 to 400 units of 0.1 dB (physical values are 0 to 40 dB). Unit: tenth dB
U32 adsl2LineStatusPcbUs	1.3.6.1.2.1.10.238.1.1.1.1.65538	Unsigned32	read-only	Indicates Power Cut-back on upstream direction. It ranges from 0 to 400 units of 0.1 dB (physical values are 0 to 40 dB) Unit: tenth dB
OCT hwadsl2Dynamicprofile	1.3.6.1.2.1.10.238.1.1.1.1.65539	OCTET STRING	read-write	The value of this object identifies the row in the ADSL Dynamic Profile Table,which applies to this ADSL line, and channels if applicable. NULL - indicates that there is no Dynamic profile bound to this port.
U32 adsl2ChStatusINP	1.3.6.1.2.1.10.238.1.2.1.1.65535	Unsigned32	read-only	The actual impulse noise protection (INP) on the bearer channel in L0 state. Unit: 0.1 DMT symbol
U32 adsl2ChStatusRSRedundancy	1.3.6.1.2.1.10.238.1.2.1.1.65536	Unsigned32	read-only	The actual number of Reed-Solomon redundancy bytes per codeword used in the latency path in which the bearer channel is transported. The value is coded in bytes. The value 0 indicates no Reed-Solomon coding. Unit: byte
U32 adsl2ChStatusRSSymbols	1.3.6.1.2.1.10.238.1.2.1.1.65537	Unsigned32	read-only	The DMT Symbol number per codeword used in the latency path in which the bearer channel is transported. Unit: 0.01 DMT symbol
U32 adsl2ChStatusInterDepth	1.3.6.1.2.1.10.238.1.2.1.1.65538	Unsigned32	read-only	The actual Reed-Solomon codeword size used in the latency path in which the bearer channel is transported. The value ranges from 1 to 4096 by step of 1. The value 1 indicates no interleaving.
U32 adsl2ChStatusSymbolLength	1.3.6.1.2.1.10.238.1.2.1.1.65539	Unsigned32	read-only	The actual number of bits per symbol assigned to the latency path in which the bearer channel is transported. This value does not include trellis overhead. Unit: bit
U32 adsl2ChStatusRSSize	1.3.6.1.2.1.10.238.1.2.1.1.65540	Unsigned32	read-only	The actual Reed-Solomon codeword size used in the latency path in which the bearer channel is transported. Unit: byte
OCT adsl2SCStatusTxPSD	1.3.6.1.2.1.10.238.1.2.2.1.65535	OCTET STRING	read-only	The PSD MASK per sub-carrier.An array of 512 16-bits values, designed for supporting up to 512 (downstream) sub-carriers. It ranges from -1400 to -300 units of 0.1 dBm/Hz (physical values are -140 to -30 dBm/Hz) Unit: 0.1 dBm/Hz
OCT adsl2SCStatusSnrMargins	1.3.6.1.2.1.10.238.1.2.2.1.65536	OCTET STRING	read-only	SNR Margin is the maximum increase in dB of the noise power received at the ATU (ATU-R on downstream direction and ATU-C on upstream direction), such that the BER requirements are met for all bearer channels received at the ATU. It ranges from -640 to 630 units of 0.1 dB (physical values are -64 to 63 dB). Unit: 0.1 dB
C32 adsl2PMLEverBeforeFecs	1.3.6.1.2.1.10.238.1.4.1.1.1.65535	Counter32	read-only	Count of seconds since agent reset that there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibited during UAS or SES. Unit: seconds
C32 adsl2PMLEverBeforeEs	1.3.6.1.2.1.10.238.1.4.1.1.1.65536	Counter32	read-only	Count of seconds since agent reset that there was: ATU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 ATU-R: FEBE >= 1 for one or more bearer channels OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1. This parameter is inhibited during UAS. Unit: seconds
C32 adsl2PMLEverBeforeSes	1.3.6.1.2.1.10.238.1.4.1.1.1.65537	Counter32	read-only	Count of seconds since agent reset that there was: ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 ATU-R: (FEBE summed over all bearer channels) >= 18 OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1 This parameter is inhibited during UAS. Unit: seconds
C32 adsl2PMLEverBeforeLoss	1.3.6.1.2.1.10.238.1.4.1.1.1.65538	Counter32	read-only	Count of seconds since agent reset that there was LOS (or LOS-FE for ATU-R). Unit: seconds
C32 adsl2PMLEverBeforeUas	1.3.6.1.2.1.10.238.1.4.1.1.1.65539	Counter32	read-only	Count of seconds in Unavailability State since agent reset. Unavailability begins at the onset of 10 contiguous severely -errored seconds, and ends at the onset of 10 contiguous seconds with no severely-errored seconds. Unit: seconds
U32 adsl2PMLInitEverBeforeFullInits	1.3.6.1.2.1.10.238.1.4.1.2.1.65535	Unsigned32	read-only	Count of full initializations attempted on the line (successful and failed) since agent reset.
U32 adsl2PMLInitEverBeforeFailedFullInits	1.3.6.1.2.1.10.238.1.4.1.2.1.65536	Unsigned32	read-only	Count of failed full initializations on the line since agent reset.
U32 adsl2PMLInitEverBeforeShortInits	1.3.6.1.2.1.10.238.1.4.1.2.1.65537	Unsigned32	read-only	Count of short initializations attempted on the line (successful and failed) since agent reset.
U32 adsl2PMLInitEverBeforeFailedShortInits	1.3.6.1.2.1.10.238.1.4.1.2.1.65538	Unsigned32	read-only	Count of failed short initializations on the line since agent reset.
U32 adsl2PMChEverBeforeCodingViolations	1.3.6.1.2.1.10.238.1.4.2.1.1.65535	Unsigned32	read-only	Count of CRC-8 (FEBE for ATU-R) anomalies occurring in the channel since agent reset. This parameter is inhibited during UAS or SES. If the CRC is applied over multiple channels, then each related CRC-8 (or FEBE) anomaly should increment each of the counters related to the individual channels.
U32 adsl2PMChEverBeforeCorrectedBlocks	1.3.6.1.2.1.10.238.1.4.2.1.1.65536	Unsigned32	read-only	Count of FEC (FFEC for ATU-R) anomalies (corrected code words) occurring in the channel since agent reset. This parameter is inhibited during UAS or SES. If the FEC is applied over multiple channels, then each related FEC (or FFEC) anomaly should increment each of the counters related to the individual channels.
ADS adsl2LConfProfTrellisMode	1.3.6.1.2.1.10.238.1.5.1.2.1.65535	Adsl2TrellisMode	read-create	Enable and disable the trellis mode. This object is defaulted enabled(2). Options: 1. disable(1) - Disable the trellis 2. enable(2) - Enable the trellis
ADS adsl2LConfProfBitSwapDs	1.3.6.1.2.1.10.238.1.5.1.2.1.65536	Adsl2BitSwap	read-create	Enable and disable the bit swap downstream of a line. This object is defaulted enable(2). Options: 1. disable(1) - Disable the bit swap downstream of a line 2. enable(2) - Enable the bit swap downstream of a line
ADS adsl2LConfProfBitSwapUs	1.3.6.1.2.1.10.238.1.5.1.2.1.65537	Adsl2BitSwap	read-create	Enable and disable the bit swap upstream of a line. This object is defaulted enable(2). Options: 1. disable(1) - Disable the bit swap upstream of a line 2. enable(2) - Enable the bit swap upstream of a line
ADS adsl2LConfProfDpboEPsd	1.3.6.1.2.1.10.238.1.5.1.2.1.65538	Adsl2DpboEpsd	read-create	This parameter defines the PSD mask that is assumed to be permitted at the exchange. This parameter shall use the same format as PSDMASKds.The maximum number of breakpoints for DPBOEPSD is 16. This is a string of 16 pairs of values in the following structure: Octets 0+1 - Index of 1st sub-carrier used in the context of a first breakpoint Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1 Octets 3-5 - Same, for a 2nd breakpoint Octets 6-8 - Same, for a 3rd breakpoint This architecture continues until octets 45-47, which are associated with a 16th breakpoint. Each subcarrier index is an unsigned number in the range 1 and NSCds. Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are in the range 0 to 190 (0 to -95dBm/Hz). When the number of breakpoints is less than 16, all remaining octets are set to the value 0xff. Unit: 0.5dBm/Hz
U32 adsl2LConfProfDpboEsEL	1.3.6.1.2.1.10.238.1.5.1.2.1.65539	Unsigned32	read-create	This configuration parameter defines the assumed electrical length of cables (E-side cables) connecting exchange based DSL services to a remote flexibility point (cabinet), that hosts the xTU-C that is subject to spectrally shaped downstream power back-off depending on this length. For this parameter the electrical length is defined as the loss (in dB) of an equivalent length of hypothetical cable at a reference frequency defined by the network operator or in spectrum management regulations. DPBOESEL shall be coded as an unsigned integer representing an electrical length from 0 dB (coded as 0) to 255.5 dB (coded as 511) in steps of 0.5 dB. All values in the range are valid.If DPBOESEL is set to zero, the DPBO in this section shall be disabled. This object is defaulted 0. Unit: 0.5dB
U32 adsl2LConfProfDpboEsCableModelA	1.3.6.1.2.1.10.238.1.5.1.2.1.65540	Unsigned32	read-create	This configuration parameter defines a cable model in terms of three scalars DPBOESCMA, DPBOESCMB and DPBOESCMC that shall be used to describe the frequency dependent loss of E-side cables.Parameters DPBOESCMA, DPBOESCMB, DPBOESCMC shall be coded as unsigned integers representing a scalar value from -1 (coded as 0) to 1.5 (coded as 640) in step of 1/256. All values in the range are valid. This object is defaulted 256.
U32 adsl2LConfProfDpboEsCableModelB	1.3.6.1.2.1.10.238.1.5.1.2.1.65541	Unsigned32	read-create	This configuration parameter defines a cable model in terms of three scalars DPBOESCMA, DPBOESCMB and DPBOESCMC that shall be used to describe the frequency dependent loss of E-side cables.Parameters DPBOESCMA, DPBOESCMB, DPBOESCMC shall be coded as unsigned integers representing a scalar value from -1 (coded as 0) to 1.5 (coded as 640) in step of 1/256. All values in the range are valid.This object is defaulted 512.
U32 adsl2LConfProfDpboEsCableModelC	1.3.6.1.2.1.10.238.1.5.1.2.1.65542	Unsigned32	read-create	This configuration parameter defines a cable model in terms of three scalars DPBOESCMA, DPBOESCMB and DPBOESCMC that shall be used to describe the frequency dependent loss of E-side cables.Parameters DPBOESCMA, DPBOESCMB, DPBOESCMC shall be coded as unsigned integers representing a scalar value from -1 (coded as 0) to 1.5 (coded as 640) in step of 1/256. All values in the range are valid.This object is defaulted 256.
U32 adsl2LConfProfDpboMus	1.3.6.1.2.1.10.238.1.5.1.2.1.65543	Unsigned32	read-create	DPBOMUS defines the assumed Minimum Usable receive Signal PSD (in dBm/Hz) for exchange based services, used to modify parameter DPBOFMAX defined below. It shall be coded as an unsigned integer representing a PSD level from 0 dBm/Hz (coded as 0) to -127.5 dBm/Hz (coded as 255) in steps of 0.5 dBm/Hz. All values in the range are valid.This object is defaulted 180. Unit: 0.5dBm/Hz
U32 adsl2LConfProfDpboFMin	1.3.6.1.2.1.10.238.1.5.1.2.1.65544	Unsigned32	read-create	DPBOFMIN defines the minimum frequency from which the DPBO shall be applied. It shall be coded as a 16 bits unsigned integer representing a frequency in multiple of 4.3125 KHz. The range of valid values is from 0 kHz (coded as 0) to 8832 kHz (coded as 2048). This object is defaulted 0. Unit: 4.3125 KHz
U32 adsl2LConfProfDpboFMax	1.3.6.1.2.1.10.238.1.5.1.2.1.65545	Unsigned32	read-create	DPBOFMAX defines the maximum frequency at which DPBO may be applied. It shall be coded as a 16 bits unsigned integer representing a frequency in multiple of 4.3125 KHz. The range of valid values is from 138 kHz (coded as 32) to 29997.75 kHz (coded as 6956). This object is defaulted 511. Unit: 4.3125 KHz
U32 adsl2ChAlarmConfProfileMonitoringRateDs	1.3.6.1.2.1.10.238.1.5.3.3.1.65535	Unsigned32	read-create	The channel monitoring rate downstream. When the value you set is larger than the value of the rate downstream defined in the channel profile, it will not be successful. The value 0 means that no threshold is specified for the associated counter. This object is defaulted 0. Unit: bits/second
U32 adsl2ChAlarmConfProfileMonitoringRateUs	1.3.6.1.2.1.10.238.1.5.3.3.1.65536	Unsigned32	read-create	The channel monitoring rate upstream. When the value you set is larger than the value of the rate upstream defined in the channel profile, it will not be successful. The value 0 means that no threshold is specified for the associated counter. This object is defaulted 0. Unit: bits/second
adsl2Mode	1.3.6.1.2.1.10.238.1.65535
ADS hwadslmodecfg	1.3.6.1.2.1.10.238.1.65535.1	Adsl2CfgMode	read-write	This object is used to change ADSL management mode. After the mode being changed, system will automatically save data and reboot. Options: 1. rfc2662(1) - Management model based on RFC2662 and RFC3440 2. rfc4706(2) - Management model based on RFC4706 3. tr165(3) - Management model based on TR-165
INT hwadslabrmodecfg	1.3.6.1.2.1.10.238.1.65535.2	INTEGER	read-write	This object is used to change abr-calculation mode. Options: 1. normalMode(1) - Change mode to normal abr-calculation 2. ptMode(2) - Change mode to pt abr-calculation
hwadsl2MIB	1.3.6.1.4.1.2011.6.138			The MIB is used for defining HUAWEI NGADSL LINE MIB objects, which expand from RFC4706 ADSL2-LINE MIB.
hwadsl2	1.3.6.1.4.1.2011.6.138.1
hwadsl2Notifications	1.3.6.1.4.1.2011.6.138.1.0
hwadsl2Line	1.3.6.1.4.1.2011.6.138.1.1
hwadsl2LineTable	1.3.6.1.4.1.2011.6.138.1.1.1		not-accessible	The table hwadsl2LineTable contains configuration, command, and status parameters of the ADSL2 line. The index of this table is an interface index where the interface has an ifType of adsl2plus(238). Several objects in this table MUST be maintained in a persistent manner.
hwadsl2LineEntry	1.3.6.1.4.1.2011.6.138.1.1.1.1		not-accessible	The table hwadsl2LineTable contains configuration, command, and status parameters of the ADSL2 line. The index of this entry is an interface index where the interface has an ifType of adsl2plus(238). Several objects in this table MUST be maintained in a persistent manner.
U32 hwadsl2LineStatusCodingGainDsInfo	1.3.6.1.4.1.2011.6.138.1.1.1.1.1	Unsigned32	read-only	The actual value of Coding gain upstream parameter,it ranges from 0 to 16 units of 0.5 dB. Unit: 0.5 dB
U32 hwadsl2LineStatusCodingGainUsInfo	1.3.6.1.4.1.2011.6.138.1.1.1.1.2	Unsigned32	read-only	The actual value of Coding gain downstream parameter,it ranges from 0 to 16 units of 0.5 dB. Unit: 0.5 dB
U32 hwadsl2LineStatusPcbDsInfo	1.3.6.1.4.1.2011.6.138.1.1.1.1.3	Unsigned32	read-only	Indicates Power Cut-back on downstream direction. It ranges from 0 to 400 units of 0.1 dB (physical values are 0 to 40 dB). Unit: tenth dB
U32 hwadsl2LineStatusPcbUsInfo	1.3.6.1.4.1.2011.6.138.1.1.1.1.4	Unsigned32	read-only	Indicates Power Cut-back on upstream direction. It ranges from 0 to 400 units of 0.1 dB (physical values are 0 to 40 dB) and the invalid value is 4294967295. Unit: tenth dB
OCT hwadsl2DynamicprofileInfo	1.3.6.1.4.1.2011.6.138.1.1.1.1.5	OCTET STRING	read-write	The value of this object identifies the row in the ADSL Dynamic Profile Table,which applies to this ADSL line, and channels if applicable. NULL -Indicates that there is no Dynamic profile bound to this port.
HWA hwadsl2LineStatusInitResult	1.3.6.1.4.1.2011.6.138.1.1.1.1.6	Hwadsl2InitResult	read-only	Indicates the result of the last full initialization performed on the line. Options: 1. noFail(0) - Successful initialization 2. configError(1) - Configuration failure 3. configNotFeasible(2) - Configuration details not supported 4. commFail(3) - Communication failure 5. noPeerXtu(4) - Peer xTU not detected 6. otherCause(5) - Other initialization failure reason 7. ginpNotSelected(6) - G.998.4 Retransmission mode was not selected while RTX_MODE = FORCED or with RTX_MODE = RTX_TESTMODE 8. invalidValue(-1) - Invalid value
ADS hwadsl2LineStatusRtxUsedDs	1.3.6.1.4.1.2011.6.138.1.1.1.1.7	Adsl2StatusRtxUsed	read-only	This parameter specifies whether G.998.4 retransmission is used in a given transmit direction. Options: 1. rtxInuse(1) - RTX in use 2. rtxUnusedModeForbidden(2) - RTX not in use, due to RTX_MODE = FORBIDDEN 3. rtxUnusedNotSupportedXtuc(3) - RTX not in use, due to not supported by the XTU-C 4. rtxUnusedNotSupportedXtur(4) - RTX not in use, due to not supported by the XTU-R 5. rtxUnusedNotSupportedXtucAndXtur(5) - RTX not in use, due to not supported by the XTU-C and XTU-R 6. invalidValue(-1) - Invalid value
INT hwadsl2LineStatusLastRetrainInfo	1.3.6.1.4.1.2011.6.138.1.1.1.1.8	INTEGER	read-only	Indicates the last retrained information performed on the line. Options: 1. none(1) - No record is available 2. cpe-l3-trigger(2) - The terminal initiates a low power consumption L3 request 3. lom-us-trigger-dra(3) - The upstream noise margin is smaller than the minimum noise margin in rate dynamic adjustment 4. lom-ds-trigger-dra(4) - The downstream noise margin is smaller than the minimum noise margin in rate dynamic adjustment 5. cpe-never-answer-oam(5) - No OAM response is received from the CPE all the time 6. cpe-no-more-answer-oam(6) - No OAM response is received from the CPE 7. persistent-ncd-us(7) - Upstream continuous no cell delineation 8. persistent-ncd-ds(8) - Downstream continuous no cell delineation 9. persistent-lcd-us(9) - Upstream continuous loss of cell delineation 10.persistent-lcd-ds(10) - Downstream continuous loss of cell delineation 11.l2-problem-co-drop(11) - The CO is faulty during the switching from L0 to L2 12.l2-problem-cpe-drop(12) - The CPE is faulty during the switching from L0 to L2 13.bitswap-refused-us-co-drop(13) - The CO goes offline when the upstream bit swap fault occurs 10 times consecutively 14.bitswap-refused-us-cpe-drop(14) - The CPE goes offline when the downstream bit swap fault occurs 10 times consecutively 15.channel-change-us-co-drop(15) - The CO goes offline when the upstream net rate changes 16.channel-change-us-cpe-drop(16) - The CPE goes offline when the upstream net rate changes 17.noise-increase-us-co-drop(17) - The CO goes offline when the upstream noise increases 18.noise-increase-us-cpe-drop(18) - The CPE goes offline when the upstream noise increases 19.bitswap-refused-ds-co-drop(19) - The CO goes offline when the downstream bit swap fault occurs 10 times consecutively 20.bitswap-refused-ds-cpe-drop(20) - The CPE goes offline when the downstream bit swap fault occurs 10 times consecutively 21.channel-change-ds-co-drop(21) - The CO goes offline when the downstream net rate changes 22.channel-change-ds-cpe-drop(22) - The CPE goes offline when the downstream net rate changes 23.noise-increase-ds-co-drop(23) - The CO goes offline when the downstream noise increases 24.noise-increase-ds-cpe-drop(24) - The CPE goes offline when the downstream noise increases 25.lom-us-co-drop(25) - The CO goes offline when the upstream noise margin is smaller than the minimum noise margin 26.lom-us-cpe-drop(26) - The CPE goes offline when the upstream noise margin is smaller than the minimum noise margin 27.lom-ds-co-drop(27) - The CO goes offline when the downstream noise margin is smaller than the minimum noise margin 28.lom-ds-cpe-drop(28) - The CPE goes offline when the downstream noise margin is smaller than the minimum noise margin 29.sra-problem-us-co-drop(29) - The CO goes offline when the upstream SRA is faulty 30.sra-problem-us-cpe-drop(30) - The CPE goes offline when the upstream SRA is faulty 31.sra-failed-us-co-drop(31) - The CO goes offline when the upstream SRA fails 32.sra-failed-us-cpe-drop(32) - The CPE goes offline when the upstream SRA fails 33.sra-problem-ds-co-drop(33) - The CO goes offline when the downstream SRA is fault 34.sra-problem-ds-cpe-drop(34) - The CPE goes offline when the downstream SRA is faulty 35.sra-rejected-ds-co-drop(35) - The CO goes offline when the downstream SRA is rejected 36.sra-rejected-ds-cpe-drop(36) - The CPE goes offline when the downstream SRA is rejected 37.bitswap-problem-us-co-drop(37) - The CO goes offline when the upstream bit swap is faulty 38.bitswap-problem-us-cpe-drop(38) - The CPE goes offline when the upstream bit swap is faulty 39.bitswap-failed-us-co-drop(39) - The CO goes offline when the upstream bit swap fails 40.bitswap-failed-us-cpe-drop(40) - The CPE goes offline when the upstream bit swap fails 41.bitswap-problem-ds-co-drop(41) - The CO goes offline when the downstream bit swap is faulty 42.bitswap-problem-ds-cpe-drop(42) - The CPE goes offline when the downstream bit swap is faulty 43.bitswap-rejected-ds-co-drop(43) - The CO goes offline when the downstream bit swap is rejected 44.bitswap-rejected-ds-cpe-drop(44) - The CPE goes offline when the downstream bit swap is rejected 45.cpe-switched-off(45) - The CPE power supply is shut down 46.cpe-lost(46) - The CPE is disconnected 47.co-reset(47) - The CO resets the chipset or line 48.co-stop(48) - The CO actively deactivate the port 49.unknown(49) - Unknown reason
U32 hwadsl2LineStatusLineRateDs	1.3.6.1.4.1.2011.6.138.1.1.1.1.9	Unsigned32	read-only	The actual line rate downstream. Unit: bits/second
U32 hwadsl2LineStatusLineRateUs	1.3.6.1.4.1.2011.6.138.1.1.1.1.10	Unsigned32	read-only	The actual line rate upstream. Unit: bits/second
hwadsl2Status	1.3.6.1.4.1.2011.6.138.1.2
hwadsl2ChannelStatusTable	1.3.6.1.4.1.2011.6.138.1.2.1		not-accessible	The table hwadsl2ChannelStatusTable contains status parameters of the ADSL2 channel and live data from equipment. The indexes of this table are ifIndex and adsl2ChStatusUnit.
hwadsl2ChannelStatusEntry	1.3.6.1.4.1.2011.6.138.1.2.1.1		not-accessible	The table hwadsl2ChannelStatusTable contains status parameters of the ADSL2 channel and live data from equipment. The indexes of this entry are ifIndex and adsl2ChStatusUnit.
C32 hwadsl2ChStatusPhyRrrcBits	1.3.6.1.4.1.2011.6.138.1.2.1.1.1	Counter32	read-only	The bits in the channel that used to retransmission. Unit: bit
C32 hwadsl2ChStatusPhyRtxQueue	1.3.6.1.4.1.2011.6.138.1.2.1.1.2	Counter32	read-only	The number of the units for retransmission.
U32 hwadsl2ChStatusINP	1.3.6.1.4.1.2011.6.138.1.2.1.1.3	Unsigned32	read-only	If retransmission is not used in a given transmit direction, this parameter reports the actual impulse noise protection (INP) on the bearer channel in the L0 state. In the L1 or L2 state, the parameter contains the INP in the previous L0 state. If retransmission is used in a given transmit direction, this parameter reports the actual impulse noise protection (INP) against SHINE on the bearer channel in the L0 state. In the L2 state, the parameter contains the INP in the previous L0 state. Unit: 0.1 DMT symbol
U32 hwadsl2ChStatusRSRedundancy	1.3.6.1.4.1.2011.6.138.1.2.1.1.4	Unsigned32	read-only	The actual number of Reed-Solomon redundancy bytes per codeword used in the latency path in which the bearer channel is transported. The value is coded in bytes. The value 0 indicates no Reed-Solomon coding. Unit: byte
U32 hwadsl2ChStatusRSSymbols	1.3.6.1.4.1.2011.6.138.1.2.1.1.5	Unsigned32	read-only	The DMT Symbol number per codeword used in the latency path in which the bearer channel is transported. Unit: 0.01 DMT symbol
U32 hwadsl2ChStatusInterDepth	1.3.6.1.4.1.2011.6.138.1.2.1.1.6	Unsigned32	read-only	The actual Reed-Solomon codeword size used in the latency path in which the bearer channel is transported. The value ranges from 1 to 4096 by step of 1. The value 1 indicates no interleaving.
U32 hwadsl2ChStatusSymbolLength	1.3.6.1.4.1.2011.6.138.1.2.1.1.7	Unsigned32	read-only	The actual number of bits per symbol assigned to the latency path in which the bearer channel is transported. This value does not include trellis overhead. Unit: bit
U32 hwadsl2ChStatusRSSize	1.3.6.1.4.1.2011.6.138.1.2.1.1.8	Unsigned32	read-only	The actual Reed-Solomon codeword size used in the latency path in which the bearer channel is transported. Unit: byte
U32 hwadsl2ChStatusActNetDataRate	1.3.6.1.4.1.2011.6.138.1.2.1.1.9	Unsigned32	read-only	In L0 state, this parameter reports the Net Data Rate at which the bearer channel is operating. In L2 state, this parameter contains the Net Data Rate in the previous L0 state. This parameter is optional if G.998.4 retransmission function is not supported. The data rate is coded in steps of 1000 bit/s.
U32 hwadsl2ChStatusActINPAgainstREIN	1.3.6.1.4.1.2011.6.138.1.2.1.1.10	Unsigned32	read-only	If retransmission is used in a given transmit direction, this parameter reports the actual impulse noise protection (INP) against REIN (under specific conditions detailed in G.998.4) on the bearer channel in the L0 state. In the L2 state, the parameter contains the INP in the previous L0 state. The value is coded in fractions of DMT symbols with a granularity of 0.1 symbols.
hwadsl2SCStatusTable	1.3.6.1.4.1.2011.6.138.1.2.2		not-accessible	The table hwadsl2SCStatusTable contains status parameters of the ADSL2 sub-carriers. The following points apply to this table: 1. The main purpose of this table is to hold the results of a DELT. 2. This table also holds parameters obtained at line initialization time. 3. The rows in this table are volatile; that is, they are lost if the SNMP agent is rebooted. 4. Due to the large OCTET STRING attributes in this table, the worst case memory requirements for this table are very high. The manager may use the row status attribute of this table to delete rows in order to reclaim memory. 5. The manager may create rows in this table. The SNMP agent may create rows in this table. Only the manager may delete rows in this table. 6. The maximum number of rows allowable in this table is indicated by the scalar attribute adsl2ScalarSCMaxInterfaces. The number of rows available in this table is indicated by the scalar attribute adsl2ScalarSCAvailInterfaces. 7. The SNMP agent is permitted to create rows in this table when a DELT completes successfully or when line initialization occurs. It is not mandatory for the SNMP agent to create rows in this table; hence, it may be necessary for the manager to create rows in this table before any results can be stored. 8. If the manager attempts to create a row in this table and there are no more rows available, the creation attempt will fail, and the response to the SNMP SET PDU will contain the error noCreation(11). 9. If the SNMP agent attempts to create a row in this table and there are no more rows available, the creation attempt will fail, and the attribute adsl2LineCmndConfLdsfFailReason will indicate the reason for the failure. The failure reason will be either tableFull(10) or noResources(11). 10. An example of use of this table is as follows: Step 1. : The DELT is started by setting the : adsl2LineCmndConfLdsf from inhibit to force. Step 2. : The DELT completes, and valid data is : available. Step 3. : The row in the adsl2SCStatusTable where the : results will be stored does not yet exist so : the SNMP agent attempts to create the row. Step 4. : Due to a low memory condition, a row in the : adsl2SCStatusTable table cannot be created at : this time. Step 5. : The reason for the failure, tableFull(10), is : indicated in the adsl2LineCmndConfLdsfFailReason : attribute. 11. Another example of use of this table is as follows : Step 1. : The DELT is started by setting the : adsl2LineCmndConfLdsf from inhibit to force. Step 2. : The DELT completes and valid data is : available. Step 3. : The row in the adsl2SCStatusTable where the : results will be stored does not yet exist so : the SNMP agent attempts to create the row. Step 4. : The row creation is successful. Step 5. : The value of the attribute : adsl2LineCmndConfLdsfFailReasonreason is set : to success(2). 12. Another example of use of this table is as follows: Step 1. : The manager creates a row in adsl2SCStatusTable : for a particular ADSL2 line. Step 2. : The DELT is started on the above-mentioned : line by setting the adsl2LineCmndConfLdsf from : inhibit to force. Step 3. : The DELT completes, and valid data is : available. Step 4. : The value of the attribute : adsl2LineCmndConfLdsfFailReasonreason is set : to success(2). The indexes of this table are ifIndex and adsl2SCStatusDirection.
hwadsl2SCStatusEntry	1.3.6.1.4.1.2011.6.138.1.2.2.1		not-accessible	The table hwadsl2SCStatusTable contains status parameters of the ADSL2 sub-carriers. The following points apply to this table: 1. The main purpose of this table is to hold the results of a DELT. 2. This table also holds parameters obtained at line initialization time. 3. The rows in this table are volatile; that is, they are lost if the SNMP agent is rebooted. 4. Due to the large OCTET STRING attributes in this table, the worst case memory requirements for this table are very high. The manager may use the row status attribute of this table to delete rows in order to reclaim memory. 5. The manager may create rows in this table. The SNMP agent may create rows in this table. Only the manager may delete rows in this table. 6. The maximum number of rows allowable in this table is indicated by the scalar attribute adsl2ScalarSCMaxInterfaces. The number of rows available in this table is indicated by the scalar attribute adsl2ScalarSCAvailInterfaces. 7. The SNMP agent is permitted to create rows in this table when a DELT completes successfully or when line initialization occurs. It is not mandatory for the SNMP agent to create rows in this table; hence, it may be necessary for the manager to create rows in this table before any results can be stored. 8. If the manager attempts to create a row in this table and there are no more rows available, the creation attempt will fail, and the response to the SNMP SET PDU will contain the error noCreation(11). 9. If the SNMP agent attempts to create a row in this table and there are no more rows available, the creation attempt will fail, and the attribute adsl2LineCmndConfLdsfFailReason will indicate the reason for the failure. The failure reason will be either tableFull(10) or noResources(11). 10. An example of use of this table is as follows: Step 1. : The DELT is started by setting the : adsl2LineCmndConfLdsf from inhibit to force. Step 2. : The DELT completes, and valid data is : available. Step 3. : The row in the adsl2SCStatusTable where the : results will be stored does not yet exist so : the SNMP agent attempts to create the row. Step 4. : Due to a low memory condition, a row in the : adsl2SCStatusTable table cannot be created at : this time. Step 5. : The reason for the failure, tableFull(10), is : indicated in the adsl2LineCmndConfLdsfFailReason : attribute. 11. Another example of use of this table is as follows : Step 1. : The DELT is started by setting the : adsl2LineCmndConfLdsf from inhibit to force. Step 2. : The DELT completes and valid data is : available. Step 3. : The row in the adsl2SCStatusTable where the : results will be stored does not yet exist so : the SNMP agent attempts to create the row. Step 4. : The row creation is successful. Step 5. : The value of the attribute : adsl2LineCmndConfLdsfFailReasonreason is set : to success(2). 12. Another example of use of this table is as follows: Step 1. : The manager creates a row in adsl2SCStatusTable : for a particular ADSL2 line. Step 2. : The DELT is started on the above-mentioned : line by setting the adsl2LineCmndConfLdsf from : inhibit to force. Step 3. : The DELT completes, and valid data is : available. Step 4. : The value of the attribute : adsl2LineCmndConfLdsfFailReasonreason is set : to success(2). The indexes of this entry are ifIndex and adsl2SCStatusDirection.
OCT hwadsl2SCStatusInfoTxPSD	1.3.6.1.4.1.2011.6.138.1.2.2.1.1	OCTET STRING	read-only	The PSD MASK per sub-carrier.An array of 512 16-bits values, designed for supporting up to 512 (downstream) sub-carriers. It ranges from -1400 to -300 units of 0.1 dBm/Hz (physical values are -140 to -30 dBm/Hz). Unit: 0.1 dBm/Hz
OCT hwadsl2SCStatusInfoSnrMargins	1.3.6.1.4.1.2011.6.138.1.2.2.1.2	OCTET STRING	read-only	SNR Margin is the maximum increase in dB of the noise power received at the ATU (ATU-R on downstream direction and ATU-C on upstream direction), such that the BER requirements are met for all bearer channels received at the ATU. It ranges from -640 to 630 units of 0.1 dB (physical values are -64 to 63 dB). Unit: 0.1 dB
hwadsl2Inventory	1.3.6.1.4.1.2011.6.138.1.3
hwadsl2PM	1.3.6.1.4.1.2011.6.138.1.4
hwadsl2PMLine	1.3.6.1.4.1.2011.6.138.1.4.1
hwadsl2PMLineCurrTable	1.3.6.1.4.1.2011.6.138.1.4.1.1		not-accessible	The table hwadsl2PMLineCurrTable contains current Performance Monitoring results of ADSL2 line. The PM counters in the table are not reset even when the xtU is reinitialized. They are re-initialized only when the agent itself is reset or reinitialized. The indexes of this table are ifIndex and adsl2PMLCurrUnit.
hwadsl2PMLineCurrEntry	1.3.6.1.4.1.2011.6.138.1.4.1.1.1		not-accessible	The table hwadsl2PMLineCurrTable contains current Performance Monitoring results of ADSL2 line. The PM counters in the table are not reset even when the xtU is reinitialized. They are re-initialized only when the agent itself is reset or reinitialized. The indexes of this entry are ifIndex and adsl2PMLCurrUnit.
OCT hwadsl2PMLCurr15MInmainpeq	1.3.6.1.4.1.2011.6.138.1.4.1.1.1.1	OCTET STRING	read-only	This parameter is a count of the INMAINPEQi anomalies occurring on the line during current 15 minutes.
C32 hwadsl2PMLCurr15MInmame	1.3.6.1.4.1.2011.6.138.1.4.1.1.1.2	Counter32	read-only	This parameter is a count of the INMAME anomalies occurring on the line during current 15 minutes.
OCT hwadsl2PMLCurr15MInmaiat	1.3.6.1.4.1.2011.6.138.1.4.1.1.1.3	OCTET STRING	read-only	This parameter is a count of the INMAIATi anomalies occurring on the line during current 15 minutes.
OCT hwadsl2PMLCurr1DayInmainpeq	1.3.6.1.4.1.2011.6.138.1.4.1.1.1.4	OCTET STRING	read-only	This parameter is a count of the INMAINPEQi anomalies occurring on the line during current 1 day.
C32 hwadsl2PMLCurr1DayInmame	1.3.6.1.4.1.2011.6.138.1.4.1.1.1.5	Counter32	read-only	This parameter is a count of the INMAME anomalies occurring on the line during current 1 day.
OCT hwadsl2PMLCurr1DayInmaiat	1.3.6.1.4.1.2011.6.138.1.4.1.1.1.6	OCTET STRING	read-only	This parameter is a count of the INMAIATi anomalies occurring on the line during current 1 day.
OCT hwadsl2PMLEverBeforeInmainpeq	1.3.6.1.4.1.2011.6.138.1.4.1.1.1.7	OCTET STRING	read-only	This parameter is a count of the INMAINPEQi anomalies occurring on the line ever before.
C32 hwadsl2PMLEverBeforeInmame	1.3.6.1.4.1.2011.6.138.1.4.1.1.1.8	Counter32	read-only	This parameter is a count of the INMAME anomalies occurring on the line ever before.
OCT hwadsl2PMLEverBeforeInmaiat	1.3.6.1.4.1.2011.6.138.1.4.1.1.1.9	OCTET STRING	read-only	This parameter is a count of the INMAIATi anomalies occurring on the line ever before.
C32 hwadsl2PMLEverBeforeFecs	1.3.6.1.4.1.2011.6.138.1.4.1.1.1.10	Counter32	read-only	Count of seconds since agent reset that there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibited during UAS or SES. Unit: seconds
C32 hwadsl2PMLEverBeforeEs	1.3.6.1.4.1.2011.6.138.1.4.1.1.1.11	Counter32	read-only	Count of seconds since agent reset that there was: ATU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 ATU-R: FEBE >= 1 for one or more bearer channels OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1. This parameter is inhibited during UAS. Unit: seconds
C32 hwadsl2PMLEverBeforeSes	1.3.6.1.4.1.2011.6.138.1.4.1.1.1.12	Counter32	read-only	Count of seconds since agent reset that there was: ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 ATU-R: (FEBE summed over all bearer channels) >= 18 OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1 This parameter is inhibited during UAS. Unit: seconds
C32 hwadsl2PMLEverBeforeLoss	1.3.6.1.4.1.2011.6.138.1.4.1.1.1.13	Counter32	read-only	Count of seconds since agent reset that there was LOS (or LOS-FE for ATU-R). Unit: seconds
C32 hwadsl2PMLEverBeforeUas	1.3.6.1.4.1.2011.6.138.1.4.1.1.1.14	Counter32	read-only	Count of seconds in Unavailability State since agent reset. Unavailability begins at the onset of 10 contiguous severely -errored seconds, and ends at the onset of 10 contiguous seconds with no severely-errored seconds. Unit: seconds
DAT hwadsl2PMLCurr15MStartTime	1.3.6.1.4.1.2011.6.138.1.4.1.1.1.15	DateAndTime	read-only	Start time of the current 15-minute performance statistics.
DAT hwadsl2PMLCurr1DayStartTime	1.3.6.1.4.1.2011.6.138.1.4.1.1.1.16	DateAndTime	read-only	Start time of the current 1-day performance statistics.
C32 hwadsl2PMLCurr15MLofs	1.3.6.1.4.1.2011.6.138.1.4.1.1.1.17	Counter32	read-only	Count of seconds in the current 15 minute interval when there was Loss of Framing. Unit: seconds
C32 hwadsl2PMLCurr15MLols	1.3.6.1.4.1.2011.6.138.1.4.1.1.1.18	Counter32	read-only	Count of seconds in the current 15 minute interval when there was Loss of Link. Unit: seconds
C32 hwadsl2PMLCurr15MLops	1.3.6.1.4.1.2011.6.138.1.4.1.1.1.19	Counter32	read-only	Count of seconds in the current 15 minute interval when there was Loss of Power. Unit: seconds
C32 hwadsl2PMLCurr1DayLofs	1.3.6.1.4.1.2011.6.138.1.4.1.1.1.20	Counter32	read-only	Count of the number of seconds when there was Loss of Framing during the current day. Unit: seconds
C32 hwadsl2PMLCurr1DayLols	1.3.6.1.4.1.2011.6.138.1.4.1.1.1.21	Counter32	read-only	Count of the number of seconds when there was Loss of Link during the current day. Unit: seconds
C32 hwadsl2PMLCurr1DayLops	1.3.6.1.4.1.2011.6.138.1.4.1.1.1.22	Counter32	read-only	Count of the number of seconds when there was Loss of Power during the current day. Unit: seconds
C32 hwadsl2PMLEverBeforeLofs	1.3.6.1.4.1.2011.6.138.1.4.1.1.1.23	Counter32	read-only	Count of the number of seconds when there was Loss of Framing since agent reset. Unit: seconds
C32 hwadsl2PMLEverBeforeLols	1.3.6.1.4.1.2011.6.138.1.4.1.1.1.24	Counter32	read-only	Count of the number of seconds when there was Loss of Link since agent reset. Unit: seconds
C32 hwadsl2PMLEverBeforeLops	1.3.6.1.4.1.2011.6.138.1.4.1.1.1.25	Counter32	read-only	Count of the number of seconds when there was Loss of Power since agent reset. Unit: seconds
C32 hwadsl2PMLCurr15MLeftrs	1.3.6.1.4.1.2011.6.138.1.4.1.1.1.26	Counter32	read-only	If retransmission is used in a given transmit direction, this parameter is a count of the seconds with a near-end leftr defect present observed over the 15 minutes accumulation period.
C32 hwadsl2PMLCurr15MEfb	1.3.6.1.4.1.2011.6.138.1.4.1.1.1.27	Counter32	read-only	If retransmission is used in a given transmit direction, this parameter is a count of the number of error-free bits observed over the 15 minutes accumulation period.
C32 hwadsl2PMLCurr15MMinEftr	1.3.6.1.4.1.2011.6.138.1.4.1.1.1.28	Counter32	read-only	If retransmission is used in a given transmit direction, this parameter reports the minimum of the EFTR(Error-free throughput rate) observed over the 15 minutes accumulation period.
C32 hwadsl2PMLCurr1DayLeftrs	1.3.6.1.4.1.2011.6.138.1.4.1.1.1.29	Counter32	read-only	If retransmission is used in a given transmit direction, this parameter is a count of the seconds with a near-end leftr defect present observed over the 24 hours accumulation period.
C32 hwadsl2PMLCurr1DayEfb	1.3.6.1.4.1.2011.6.138.1.4.1.1.1.30	Counter32	read-only	If retransmission is used in a given transmit direction, this parameter is a count of the number of error-free bits observed over the 24 hours accumulation period.
C32 hwadsl2PMLCurr1DayMinEftr	1.3.6.1.4.1.2011.6.138.1.4.1.1.1.31	Counter32	read-only	If retransmission is used in a given transmit direction, this parameter reports the minimum of the EFTR(Error-free throughput rate) observed over the 24 hours accumulation period.
C32 hwadsl2PMLEverBeforeLeftrs	1.3.6.1.4.1.2011.6.138.1.4.1.1.1.32	Counter32	read-only	If retransmission is used in a given transmit direction, this parameter is a count of the seconds with a near-end leftr defect present observed ever before.
C32 hwadsl2PMLEverBeforeEfb	1.3.6.1.4.1.2011.6.138.1.4.1.1.1.33	Counter32	read-only	If retransmission is used in a given transmit direction, this parameter is a count of the number of error-free bits observed ever before.
C32 hwadsl2PMLEverBeforeMinEftr	1.3.6.1.4.1.2011.6.138.1.4.1.1.1.34	Counter32	read-only	If retransmission is used in a given transmit direction, this parameter reports the minimum of the EFTR(Error-free throughput rate) observed ever before.
hwadsl2PMLineHist15MinTable	1.3.6.1.4.1.2011.6.138.1.4.1.2		not-accessible	The table hwadsl2PMLineHist15MinTable contains Performance Monitoring results of ADSL2 line at last 15 minutes. The PM counters in the table are not reset even when the xtU is reinitialized. They are re-initialized only when the agent itself is reset or reinitialized. The indexes of this table are ifIndex, adsl2PMLHist15MUnit and adsl2PMLHist15MInterval.
hwadsl2PMLineHist15MinEntry	1.3.6.1.4.1.2011.6.138.1.4.1.2.1		not-accessible	The table hwadsl2PMLineHist15MinTable contains Performance Monitoring results of ADSL2 line at last 15 minutes. The PM counters in the table are not reset even when the xtU is reinitialized. They are re-initialized only when the agent itself is reset or reinitialized. The indexes of this entry are ifIndex, adsl2PMLHist15MUnit and adsl2PMLHist15MInterval.
OCT hwadsl2PMLHist15MInmainpeq	1.3.6.1.4.1.2011.6.138.1.4.1.2.1.1	OCTET STRING	read-only	This parameter is a count of the INMAINPEQi anomalies occurring on the line at last 15 minutes.
C32 hwadsl2PMLHist15MInmame	1.3.6.1.4.1.2011.6.138.1.4.1.2.1.2	Counter32	read-only	This parameter is a count of the INMAME anomalies occurring on the line at last 15 minutes.
OCT hwadsl2PMLHist15MInmaiat	1.3.6.1.4.1.2011.6.138.1.4.1.2.1.3	OCTET STRING	read-only	This parameter is a count of the INMAIATi anomalies occurring on the line at last 15 minutes.
DAT hwadsl2PMLHist15MStartTime	1.3.6.1.4.1.2011.6.138.1.4.1.2.1.4	DateAndTime	read-only	Start time of the historical 15-minute performance statistics.
C32 hwadsl2PMLHist15MLofs	1.3.6.1.4.1.2011.6.138.1.4.1.2.1.5	Counter32	read-only	Count of seconds in the interval when there was Loss of Framing. Unit: seconds
C32 hwadsl2PMLHist15MLols	1.3.6.1.4.1.2011.6.138.1.4.1.2.1.6	Counter32	read-only	Count of seconds in the interval when there was Loss of Link. Unit: seconds
C32 hwadsl2PMLHist15MLops	1.3.6.1.4.1.2011.6.138.1.4.1.2.1.7	Counter32	read-only	Count of seconds in the interval when there was Loss of Power. Unit: seconds
C32 hwadsl2PMLHist15MLeftrs	1.3.6.1.4.1.2011.6.138.1.4.1.2.1.8	Counter32	read-only	If retransmission is used in a given transmit direction, this parameter is a count of the seconds with a near-end leftr defect present observed over the 15 minutes accumulation period.
C32 hwadsl2PMLHist15MEfb	1.3.6.1.4.1.2011.6.138.1.4.1.2.1.9	Counter32	read-only	If retransmission is used in a given transmit direction, this parameter is a count of the number of error-free bits observed over the 15 minutes accumulation period.
C32 hwadsl2PMLHist15MMinEftr	1.3.6.1.4.1.2011.6.138.1.4.1.2.1.10	Counter32	read-only	If retransmission is used in a given transmit direction, this parameter reports the minimum of the EFTR(Error-free throughput rate) observed over the 15 minutes accumulation period.
hwadsl2PMLineHist1DayTable	1.3.6.1.4.1.2011.6.138.1.4.1.3		not-accessible	The table hwadsl2PMLineHist1DayTable contains Performance Monitoring results of ADSL2 line at last 1 day. The PM counters in the table are not reset even when the xtU is reinitialized. They are re-initialized only when the agent itself is reset or reinitialized. The indexes of this table are ifIndex, adsl2PMLHist1DUnit and adsl2PMLHist1DInterval.
hwadsl2PMLineHist1DayEntry	1.3.6.1.4.1.2011.6.138.1.4.1.3.1		not-accessible	The table hwadsl2PMLineHist1DayTable contains Performance Monitoring results of ADSL2 line at last 1 day. The PM counters in the table are not reset even when the xtU is reinitialized. They are re-initialized only when the agent itself is reset or reinitialized. The indexes of this entry are ifIndex, adsl2PMLHist1DUnit and adsl2PMLHist1DInterval.
OCT hwadsl2PMLHist1DayInmainpeq	1.3.6.1.4.1.2011.6.138.1.4.1.3.1.1	OCTET STRING	read-only	This parameter is a count of the INMAINPEQi anomalies occurring on the line at last 1 day.
C32 hwadsl2PMLHist1DayInmame	1.3.6.1.4.1.2011.6.138.1.4.1.3.1.2	Counter32	read-only	This parameter is a count of the INMAME anomalies occurring on the line at last 1 day.
OCT hwadsl2PMLHist1DayInmaiat	1.3.6.1.4.1.2011.6.138.1.4.1.3.1.3	OCTET STRING	read-only	This parameter is a count of the INMAIATi anomalies occurring on the line at last 1 day.
DAT hwadsl2PMLHist1DayStartTime	1.3.6.1.4.1.2011.6.138.1.4.1.3.1.4	DateAndTime	read-only	Start time of the historical 1-day performance statistics.
C32 hwadsl2PMLHist1DayLofs	1.3.6.1.4.1.2011.6.138.1.4.1.3.1.5	Counter32	read-only	Count of seconds during this interval that there was Loss of Framing. Unit: seconds
C32 hwadsl2PMLHist1DayLols	1.3.6.1.4.1.2011.6.138.1.4.1.3.1.6	Counter32	read-only	Count of seconds during this interval that there was Loss of Link. Unit: seconds
C32 hwadsl2PMLHist1DayLops	1.3.6.1.4.1.2011.6.138.1.4.1.3.1.7	Counter32	read-only	Count of seconds during this interval that there was Loss of Power. Unit: seconds
C32 hwadsl2PMLHist1DLeftrs	1.3.6.1.4.1.2011.6.138.1.4.1.3.1.8	Counter32	read-only	If retransmission is used in a given transmit direction, this parameter is a count of the seconds with a near-end leftr defect present observed over the 24 hours accumulation period.
C32 hwadsl2PMLHist1DEfb	1.3.6.1.4.1.2011.6.138.1.4.1.3.1.9	Counter32	read-only	If retransmission is used in a given transmit direction, this parameter is a count of the number of error-free bits observed over the 24 hours accumulation period.
C32 hwadsl2PMLHist1DMinEftr	1.3.6.1.4.1.2011.6.138.1.4.1.3.1.10	Counter32	read-only	If retransmission is used in a given transmit direction, this parameter reports the minimum of the EFTR(Error-free throughput rate) observed over the 24 hours accumulation period.
hwadsl2PMLineCurrInitTable	1.3.6.1.4.1.2011.6.138.1.4.1.4		not-accessible	The table hwadsl2PMLineCurrInitTable contains current initialization counters of the ADSL2 line. The PM counters in the table are not reset even when the XTU is reinitialized. They are reinitialized only when the agent itself is reset or reinitialized. The index of this table is ifIndex.
hwadsl2PMLineCurrInitEntry	1.3.6.1.4.1.2011.6.138.1.4.1.4.1		not-accessible	The table hwadsl2PMLineCurrInitTable contains current initialization counters of the ADSL2 line. The PM counters in the table are not reset even when the XTU is reinitialized. They are reinitialized only when the agent itself is reset or reinitialized. The index of this entry is ifIndex.
U32 hwadsl2PMLInitEverBeforeFullInits	1.3.6.1.4.1.2011.6.138.1.4.1.4.1.1	Unsigned32	read-only	Count of full initializations attempted on the line (successful and failed) since agent reset.
U32 hwadsl2PMLInitEverBeforeFailedFullInits	1.3.6.1.4.1.2011.6.138.1.4.1.4.1.2	Unsigned32	read-only	Count of failed full initializations on the line since agent reset.
U32 hwadsl2PMLInitEverBeforeShortInits	1.3.6.1.4.1.2011.6.138.1.4.1.4.1.3	Unsigned32	read-only	Count of short initializations attempted on the line (successful and failed) since agent reset.
U32 hwadsl2PMLInitEverBeforeFailedShortInits	1.3.6.1.4.1.2011.6.138.1.4.1.4.1.4	Unsigned32	read-only	Count of failed short initializations on the line since agent reset.
DAT hwadsl2PMLineCurrInit15MStartTime	1.3.6.1.4.1.2011.6.138.1.4.1.4.1.5	DateAndTime	read-only	Start time of the current init 15-minute performance statistics.
DAT hwadsl2PMLineCurrInit1DayStartTime	1.3.6.1.4.1.2011.6.138.1.4.1.4.1.6	DateAndTime	read-only	Start time of the current init 1-day performance statistics.
hwadsl2PMLineInitHist15MinTable	1.3.6.1.4.1.2011.6.138.1.4.1.5		not-accessible	The table hwadsl2PMLineInitHist15MinTable contains Performance Monitoring results of ADSL2 line initialize at last 15 minutes. The PM counters in the table are not reset even when the xtU is reinitialized. They are re-initialized only when the agent itself is reset or reinitialized. The indexes of this table are ifIndex and adsl2PMLHistInit15MInterval.
hwadsl2PMLineInitHist15MinEntry	1.3.6.1.4.1.2011.6.138.1.4.1.5.1		not-accessible	The table hwadsl2PMLineInitHist15MinTable contains Performance Monitoring results of ADSL2 line initialize at last 15 minutes. The PM counters in the table are not reset even when the xtU is reinitialized. They are re-initialized only when the agent itself is reset or reinitialized. The indexes of this entry are ifIndex and adsl2PMLHistInit15MInterval.
DAT hwadsl2PMLineInitHist15MinStartTime	1.3.6.1.4.1.2011.6.138.1.4.1.5.1.1	DateAndTime	read-only	Start time of the historical init 15-minute performance statistics.
hwadsl2PMLineInitHist1DayTable	1.3.6.1.4.1.2011.6.138.1.4.1.6		not-accessible	The table hwadsl2PMLineInitHist1DayTable contains Performance Monitoring results of ADSL2 line initialize at last one day. The indexes of this table are ifIndex and adsl2PMLHistinit1DInterval.
hwadsl2PMLineInitHist1DayEntry	1.3.6.1.4.1.2011.6.138.1.4.1.6.1		not-accessible	The table hwadsl2PMLineInitHist1DayTable contains Performance Monitoring results of ADSL2 line initialize at last one day. The indexes of this entry are ifIndex and adsl2PMLHistinit1DInterval.
DAT hwadsl2PMLineInitHist1DayStartTime	1.3.6.1.4.1.2011.6.138.1.4.1.6.1.1	DateAndTime	read-only	Start time of the historical init 1-day performance statistics.
hwadsl2PMChannel	1.3.6.1.4.1.2011.6.138.1.4.2
hwadsl2PMChCurrTable	1.3.6.1.4.1.2011.6.138.1.4.2.1		not-accessible	The table hwadsl2PMChCurrTable contains some extended current Performance Monitoring results of the ADSL2 channel. The PM counters in the table are not reset even when the XTU is reinitialized. They are reinitialized only when the agent itself is reset or reinitialized. The indexes of this table are ifIndex and adsl2PMChCurrUnit.
hwadsl2PMChCurrEntry	1.3.6.1.4.1.2011.6.138.1.4.2.1.1		not-accessible	The table hwadsl2PMChCurrTable contains some extended current Performance Monitoring results of the ADSL2 channel. The PM counters in the table are not reset even when the XTU is reinitialized. They are reinitialized only when the agent itself is reset or reinitialized. The indexes of this entry are ifIndex and adsl2PMChCurrUnit.
C32 hwadsl2PMChCurr15MRtxCW	1.3.6.1.4.1.2011.6.138.1.4.2.1.1.1	Counter32	read-only	Count of units request retransmission on this channel within the current 15 minute interval.
C32 hwadsl2PMChCurr15MRtxCorrectedCW	1.3.6.1.4.1.2011.6.138.1.4.2.1.1.2	Counter32	read-only	Count of units corrected by retransmission on this channel within the current 15 minute interval.
C32 hwadsl2PMChCurr15MRtxUncorrectedCW	1.3.6.1.4.1.2011.6.138.1.4.2.1.1.3	Counter32	read-only	Count of units uncorrected by retransmission on this channel within the current 15 minute interval.
C32 hwadsl2PMChCurr1DayRtxCW	1.3.6.1.4.1.2011.6.138.1.4.2.1.1.4	Counter32	read-only	Count of units request retransmission on this channel during the current day.
C32 hwadsl2PMChCurr1DayRtxCorrectedCW	1.3.6.1.4.1.2011.6.138.1.4.2.1.1.5	Counter32	read-only	Count of units corrected by retransmission on this channel during the current day.
C32 hwadsl2PMChCurr1DayRtxUncorrectedCW	1.3.6.1.4.1.2011.6.138.1.4.2.1.1.6	Counter32	read-only	Count of units uncorrected by retransmission on this channel during the current day.
C32 hwadsl2PMChEverBeforeRtxCW	1.3.6.1.4.1.2011.6.138.1.4.2.1.1.7	Counter32	read-only	Count of units request retransmission on this channel ever before.
C32 hwadsl2PMChEverBeforeRtxCorrectedCW	1.3.6.1.4.1.2011.6.138.1.4.2.1.1.8	Counter32	read-only	Count of units corrected by retransmission on this channel ever before.
C32 hwadsl2PMChEverBeforeRtxUncorrectedCW	1.3.6.1.4.1.2011.6.138.1.4.2.1.1.9	Counter32	read-only	Count of units uncorrected by retransmission on this channel ever before.
U32 hwadsl2PMChEverBeforeCodingViolations	1.3.6.1.4.1.2011.6.138.1.4.2.1.1.10	Unsigned32	read-only	Count of CRC-8 (FEBE for ATU-R) anomalies occurring in the channel since agent reset. This parameter is inhibited during UAS or SES. If the CRC is applied over multiple channels, then each related CRC-8 (or FEBE) anomaly should increment each of the counters related to the individual channels.
U32 hwadsl2PMChEverBeforeCorrectedBlocks	1.3.6.1.4.1.2011.6.138.1.4.2.1.1.11	Unsigned32	read-only	Count of FEC (FFEC for ATU-R) anomalies (corrected code words) occurring in the channel since agent reset. This parameter is inhibited during UAS or SES. If the FEC is applied over multiple channels, then each related FEC (or FFEC) anomaly should increment each of the counters related to the individual channels.
DAT hwadsl2PMChCur15MStartTime	1.3.6.1.4.1.2011.6.138.1.4.2.1.1.12	DateAndTime	read-only	Start time of the channel current 15-minute performance statistics.
DAT hwadsl2PMChCur1DayStartTime	1.3.6.1.4.1.2011.6.138.1.4.2.1.1.13	DateAndTime	read-only	Start time of the channel current 1-day performance statistics.
hwadsl2PMChHist15MinTable	1.3.6.1.4.1.2011.6.138.1.4.2.2		not-accessible	The table hwadsl2PMChHist15MinTable contains PM channel history for 15min intervals of the ADSL2 channel. The indexes of this table are ifIndex,adsl2PMChHist15MUnit and adsl2PMChHist15MInterval.
hwadsl2PMChHist15MinEntry	1.3.6.1.4.1.2011.6.138.1.4.2.2.1		not-accessible	The table hwadsl2PMChHist15MinTable contains PM channel history for 15min intervals of the ADSL2 channel. The indexes of this entry are ifIndex,adsl2PMChHist15MUnit and adsl2PMChHist15MInterval.
C32 hwadsl2PMChHist15MRtxCW	1.3.6.1.4.1.2011.6.138.1.4.2.2.1.1	Counter32	read-only	Count of units request retransmission on this channel within the last 15 minutes interval.
C32 hwadsl2PMChHist15MRtxCorrectedCW	1.3.6.1.4.1.2011.6.138.1.4.2.2.1.2	Counter32	read-only	Count of units corrected by retransmission on this channel within the last 15 minutes interval.
C32 hwadsl2PMChHist15MRtxUncorrectedCW	1.3.6.1.4.1.2011.6.138.1.4.2.2.1.3	Counter32	read-only	Count of units uncorrected by retransmission on this channel within the last 15 minutes interval.
DAT hwadsl2PMChHist15MStartTime	1.3.6.1.4.1.2011.6.138.1.4.2.2.1.4	DateAndTime	read-only	Start time of the historical 15-minute performance statistics.
hwadsl2PMChHist1DTable	1.3.6.1.4.1.2011.6.138.1.4.2.3		not-accessible	The table hwadsl2PMChHist1DayTable contains some extended PM channel history for 1-day intervals of ADSL2. The indexes of this table are ifIndex,adsl2PMChHist1DUnit and adsl2PMChHist1DInterval.
hwadsl2PMChHist1DEntry	1.3.6.1.4.1.2011.6.138.1.4.2.3.1		not-accessible	The table hwadsl2PMChHist1DayTable contains some extended PM channel history for 1-day intervals of ADSL2. The indexes of this entry are ifIndex,adsl2PMChHist1DUnit and adsl2PMChHist1DInterval.
C32 hwadsl2PMChHist1DRtxCW	1.3.6.1.4.1.2011.6.138.1.4.2.3.1.1	Counter32	read-only	Count of units request retransmission on this channel within the last 1 day interval.
C32 hwadsl2PMChHist1DRtxCorrectedCW	1.3.6.1.4.1.2011.6.138.1.4.2.3.1.2	Counter32	read-only	Count of units corrected by retransmission on this channel within the last 1 day interval.
C32 hwadsl2PMChHist1DRtxUncorrectedCW	1.3.6.1.4.1.2011.6.138.1.4.2.3.1.3	Counter32	read-only	Count of units uncorrected by retransmission on this channel within the last 1 day interval.
DAT hwadsl2PMChHist1DStartTime	1.3.6.1.4.1.2011.6.138.1.4.2.3.1.4	DateAndTime	read-only	Start time of the historical 1-day performance statistics.
hwadsl2Profile	1.3.6.1.4.1.2011.6.138.1.5
hwadsl2ProfileLine	1.3.6.1.4.1.2011.6.138.1.5.1
hwadsl2LineConfProfTable	1.3.6.1.4.1.2011.6.138.1.5.1.2		not-accessible	The table hwadsl2LineConfProfTable contains huawei private ADSL2 line profile configuration.Entries in this table MUST be maintained in a persistent manner. The index of this table is adsl2LConfProfProfileName.
hwadsl2LineConfProfEntry	1.3.6.1.4.1.2011.6.138.1.5.1.2.1		not-accessible	The table hwadsl2LineConfProfTable contains huawei private ADSL2 line profile configuration.Entries in this table MUST be maintained in a persistent manner. The index of this entry is adsl2LConfProfProfileName.
U32 hwadsl2LConfProfInmIatoDs	1.3.6.1.4.1.2011.6.138.1.5.1.2.1.1	Unsigned32	read-create	The parameter of downstream impulse noise monitoring inter arrival time offset. This is the Inter Arrival Time Offset that the xTU receiver shall use to determine in which bin of the Inter Arrival Time histogram the IAT is reported. The valid values for INMIATO ranges from 3 to 511 DMT symbols in steps of 1 DMT symbol.
U32 hwadsl2LConfProfInmIatsDs	1.3.6.1.4.1.2011.6.138.1.5.1.2.1.2	Unsigned32	read-create	The parameter of downstream impulse noise monitoring inter arrival time step. This is the Inter Arrival Time Step that the xTU receiver shall use to determine in which bin of the Inter Arrival Time histogram the IAT is reported. The valid values for INMIATS ranges from 0 to 7 in steps of 1.
U32 hwadsl2LConfProfInmCcDs	1.3.6.1.4.1.2011.6.138.1.5.1.2.1.3	Unsigned32	read-create	The parameter of Downstream impulse noise monitoring cluster continuation value. This is the Cluster Continuation value that the xTU receiver shall use in the cluster indication process described in the relevant ITU-T Recommendation. The valid values for INMCC range from 0 to 64 DMT symbols in steps of 1 DMT symbol.
U32 hwadsl2LConfProfInmInpeqModeDs	1.3.6.1.4.1.2011.6.138.1.5.1.2.1.4	Unsigned32	read-create	The parameter of Downstream impulse noise monitoring equivalent impulse noise protect mode. This is the INM Equivalent INP Mode that the xTU receiver shall use in the computation of the Equivalent INP, as defined in the relevant ITU-T Recommendation. The valid values for INM_INPEQ_MODE are 0, 1, 2, 3, and 4.
ADS hwadsl2LConfProfRfiBands	1.3.6.1.4.1.2011.6.138.1.5.1.2.1.5	Adsl2RfiBand	read-create	The RFI notch parameter. It is a string consist of begin tone index, end tone index and psd value. This is a string of 4 groups of values in the following structure: Octets 0+1 - Index of start sub-carrier used in the context of a first group Octets 2+3 - Index of end sub-carrier used in the context of a first group Octet 4+5 - The psd value configurated in the first group Octets 6-11 - Same, for a 2nd group This architecture continues until octets 22-23, which are associated with a 4th group.It can contain as most as 4 groups.
ADS hwadsl2LConfProfReferenceClock	1.3.6.1.4.1.2011.6.138.1.5.1.2.1.6	Adsl2LConfProfReferenceClockType	read-create	This object configures the clock reference for the ATU-C in an ADSL Line.
U32 hwadsl2LConfProfL3Time	1.3.6.1.4.1.2011.6.138.1.5.1.2.1.7	Unsigned32	read-create	This minimum time (in seconds) between an Entry into the L3 state and the L0 or L2 state. Unit: seconds
U32 hwadsl2LConfProfDpboEselMin	1.3.6.1.4.1.2011.6.138.1.5.1.2.1.8	Unsigned32	read-create	DPBOESELMIN in dB is the minimum of all main cable losses for the KVz supplied when using the SOL model (expansion of a KVz and ADSL2 provision of additional KVz areas from this KVz using cross-cables to additional KVz), including the KVz at the MSAN site. This value must be adjustable as the minimum requirement via the SNMP interface in the configuration profile for each ADSL2 port, and is set individually for each MSAN site and usage. As an option, adjustment can be done for each MSAN or line card, thus taking effect for entire port groups. It is used only for determining the MUF. Unit: 0.5dB
ADS hwadsl2LConfProfTrellisMode	1.3.6.1.4.1.2011.6.138.1.5.1.2.1.9	Adsl2TrellisMode	read-create	Enables and disables the trellis mode. This object is defaulted enabled(2).
ADS hwadsl2LConfProfBitSwapDs	1.3.6.1.4.1.2011.6.138.1.5.1.2.1.10	Adsl2BitSwap	read-create	Enables and disables the bit swap downstream of a line.
ADS hwadsl2LConfProfBitSwapUs	1.3.6.1.4.1.2011.6.138.1.5.1.2.1.11	Adsl2BitSwap	read-create	Enables and disables the bit swap upstream of a line.
ADS hwadsl2LConfProfDpboEPsd	1.3.6.1.4.1.2011.6.138.1.5.1.2.1.12	Adsl2DpboEpsd	read-create	This parameter defines the PSD mask that is assumed to be permitted at the exchange. This parameter shall use the same format as PSDMASKds.The maximum number of breakpoints for DPBOEPSD is 16. This is a string of 16 pairs of values in the following structure: Octets 0+1 - Index of 1st sub-carrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1 Octets 3-5 - Same, for a 2nd breakpoint Octets 6-8 - Same, for a 3rd breakpoint This architecture continues until octets 45-47, which are associated with a 16th breakpoint. Each subcarrier index is an unsigned number in the range 1 and NSCds. Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are in the range 0 to 190 (0 to -95dBm/Hz). When the number of breakpoints is less than 16, all remaining octets are set to the value 0xff.
U32 hwadsl2LConfProfDpboEsEL	1.3.6.1.4.1.2011.6.138.1.5.1.2.1.13	Unsigned32	read-create	This configuration parameter defines the assumed electrical length of cables (E-side cables) connecting exchange based DSL services to a remote flexibility point (cabinet), that hosts the xTU-C that is subject to spectrally shaped downstream power back-off depending on this length. For this parameter the electrical length is defined as the loss (in dB) of an equivalent length of hypothetical cable at a reference frequency defined by the network operator or in spectrum management regulations. DPBOESEL shall be coded as an unsigned integer representing an electrical length from 0 dB (coded as 0) to 255.5 dB (coded as 511) in steps of 0.5 dB. All values in the range are valid.If DPBOESEL is set to zero, the DPBO in this section shall be disabled. Unit: 0.5dB
U32 hwadsl2LConfProfDpboEsCableModelA	1.3.6.1.4.1.2011.6.138.1.5.1.2.1.14	Unsigned32	read-create	This configuration parameter defines a cable model in terms of three scalars DPBOESCMA, DPBOESCMB and DPBOESCMC that shall be used to describe the frequency dependent loss of E-side cables.Parameters DPBOESCMA, DPBOESCMB, DPBOESCMC shall be coded as unsigned integers representing a scalar value from -1 (coded as 0) to 1.5 (coded as 640) in step of 1/256. All values in the range are valid.
U32 hwadsl2LConfProfDpboEsCableModelB	1.3.6.1.4.1.2011.6.138.1.5.1.2.1.15	Unsigned32	read-create	This configuration parameter defines a cable model in terms of three scalars DPBOESCMA, DPBOESCMB and DPBOESCMC that shall be used to describe the frequency dependent loss of E-side cables.Parameters DPBOESCMA, DPBOESCMB, DPBOESCMC shall be coded as unsigned integers representing a scalar value from -1 (coded as 0) to 1.5 (coded as 640) in step of 1/256. All values in the range are valid.
U32 hwadsl2LConfProfDpboEsCableModelC	1.3.6.1.4.1.2011.6.138.1.5.1.2.1.16	Unsigned32	read-create	This configuration parameter defines a cable model in terms of three scalars DPBOESCMA, DPBOESCMB and DPBOESCMC that shall be used to describe the frequency dependent loss of E-side cables.Parameters DPBOESCMA, DPBOESCMB, DPBOESCMC shall be coded as unsigned integers representing a scalar value from -1 (coded as 0) to 1.5 (coded as 640) in step of 1/256. All values in the range are valid.
U32 hwadsl2LConfProfDpboMus	1.3.6.1.4.1.2011.6.138.1.5.1.2.1.17	Unsigned32	read-create	DPBOMUS defines the assumed Minimum Usable receive Signal PSD (in dBm/Hz) for exchange based services, used to modify parameter DPBOFMAX defined below. It shall be coded as an unsigned integer representing a PSD level from 0 dBm/Hz (coded as 0) to -127.5 dBm/Hz (coded as 255) in steps of 0.5 dBm/Hz. All values in the range are valid. Unit: 0.5dBm/Hz
U32 hwadsl2LConfProfDpboFMin	1.3.6.1.4.1.2011.6.138.1.5.1.2.1.18	Unsigned32	read-create	DPBOFMIN defines the minimum frequency from which the DPBO shall be applied. It shall be coded as a 16 bits unsigned integer representing a frequency in multiple of 4.3125 KHz. The range of valid values is from 0 kHz (coded as 0) to 8832 kHz (coded as 2048). Unit: 4.3125 KHz
U32 hwadsl2LConfProfDpboFMax	1.3.6.1.4.1.2011.6.138.1.5.1.2.1.19	Unsigned32	read-create	DPBOFMAX defines the maximum frequency at which DPBO may be applied. It shall be coded as a 16 bits unsigned integer representing a frequency in multiple of 4.3125 KHz. The range of valid values is from 138 kHz (coded as 32) to 29997.75 kHz (coded as 6956). Unit: 4.3125 KHz
hwadsl2ProfileChannel	1.3.6.1.4.1.2011.6.138.1.5.2
hwadsl2ChConfProfileTable	1.3.6.1.4.1.2011.6.138.1.5.2.1		not-accessible	The table hwadsl2ChConfProfileTable contains huawei private ADSL2 channel profile configuration. Entries in this table MUST be maintained in a persistent manner. The index of this table is adsl2ChConfProfProfileName.
hwadsl2ChConfProfileEntry	1.3.6.1.4.1.2011.6.138.1.5.2.1.1		not-accessible	The table hwadsl2ChConfProfileTable contains huawei private ADSL2 channel profile configuration. Entries in this table MUST be maintained in a persistent manner. The index of this entry is adsl2ChConfProfProfileName.
ADS hwadsl2ChConfProfDataPathMode	1.3.6.1.4.1.2011.6.138.1.5.2.1.1.1	Adsl2DataPathMode	read-create	The channel data path mode. Options: 1. atm(1) - ATM data path 2. ptm(2) - PTM data path 3. both(3) - ATM and PTM data path Huawei defined.
ADS hwadsl2ChConfProfErasureDecoding	1.3.6.1.4.1.2011.6.138.1.5.2.1.1.2	Adsl2ProfSwitchType	read-create	Enable or disable the erasure decoding of a channel. Options: 1. enable(1) - Open the erasure decoding of a channel 2. disable(2) - Close the erasure decoding of a channel
ADS hwadsl2ChConfProfPhyRcontrolDs	1.3.6.1.4.1.2011.6.138.1.5.2.1.1.3	Adsl2PhyRControl	read-create	To enable or disable the retransmission function of downstream PHY-R. Options: 1. enable(1) - Enable the retransmission function of downstream PHY-R 2. disable(2) - Disable the retransmission function of downstream PHY-R
ADS hwadsl2ChConfProfPhyRcontrolUs	1.3.6.1.4.1.2011.6.138.1.5.2.1.1.4	Adsl2PhyRControl	read-create	To enable or disable the retransmission function of upstream PHY-R. Options: 1. enable(1) - Enable the retransmission function of upstream PHY-R 2. disable(2) - Disable the retransmission function of upstream PHY-R
ADS hwadsl2ChConfProfInpMaxDs	1.3.6.1.4.1.2011.6.138.1.5.2.1.1.5	Adsl2SymbolProtection	read-create	Maximum Impulse Noise Protection on downstream direction.
ADS hwadsl2ChConfProfInpMaxUs	1.3.6.1.4.1.2011.6.138.1.5.2.1.1.6	Adsl2SymbolProtection	read-create	Maximum Impulse Noise Protection on upstream direction.
U32 hwadsl2ChConfProfMinRtxRatioDs	1.3.6.1.4.1.2011.6.138.1.5.2.1.1.7	Unsigned32	read-create	This object is used to config the minimum retransmission band width parameter downstream.
U32 hwadsl2ChConfProfMinRtxRatioUs	1.3.6.1.4.1.2011.6.138.1.5.2.1.1.8	Unsigned32	read-create	This object is used to config the minimum retransmission band width parameter upstream.
U32 hwadsl2ChConfProfMinRSoverheadDs	1.3.6.1.4.1.2011.6.138.1.5.2.1.1.9	Unsigned32	read-create	This object is used to config the minimum RSoverhead parameter downstream.
U32 hwadsl2ChConfProfMinRSoverheadUs	1.3.6.1.4.1.2011.6.138.1.5.2.1.1.10	Unsigned32	read-create	This object is used to config the minimum RSoverhead parameter upstream.
hwadsl2ProfileAlarmConf	1.3.6.1.4.1.2011.6.138.1.5.3
hwadsl2ChAlarmConfProfileTable	1.3.6.1.4.1.2011.6.138.1.5.3.1		not-accessible	The table hwadsl2ChAlarmConfProfileTable contains ADSL2 channel PM thresholds profiles. Entries in this table MUST be maintained in a persistent manner. The index of this table is adsl2ChAlarmConfProfileName.
hwadsl2ChAlarmConfProfileEntry	1.3.6.1.4.1.2011.6.138.1.5.3.1.1		not-accessible	The table hwadsl2ChAlarmConfProfileTable contains ADSL2 channel PM thresholds profiles. Entries in this table MUST be maintained in a persistent manner. The index of this entry is adsl2ChAlarmConfProfileName.
U32 hwadsl2ChAlarmConfProfileMonitoringRateDs	1.3.6.1.4.1.2011.6.138.1.5.3.1.1.1	Unsigned32	read-create	The channel monitoring rate downstream. When the value you set is larger than the value of the rate downstream defined in the channel profile, it will not be successful. The value 0 means that no threshold is specified for the associated counter. Unit: bits/second
U32 hwadsl2ChAlarmConfProfileMonitoringRateUs	1.3.6.1.4.1.2011.6.138.1.5.3.1.1.2	Unsigned32	read-create	The channel monitoring rate upstream. When the value you set is larger than the value of the rate upstream defined in the channel profile, it will not be successful. The value 0 means that no threshold is specified for the associated counter. Unit: bits/second
hwadsl2LineAlarmConfProfileTable	1.3.6.1.4.1.2011.6.138.1.5.3.2		not-accessible	The table hwadsl2LineAlarmConfProfileTable contains ADSL2 line PM thresholds profiles. A default profile with an index of 'DEFVAL' will always exist, and its parameters will be set to vendor- specific values, unless otherwise specified in this document. The index of this table is adsl2LineAlarmConfProfileName.
hwadsl2LineAlarmConfProfileEntry	1.3.6.1.4.1.2011.6.138.1.5.3.2.1		not-accessible	The table hwadsl2LineAlarmConfProfileTable contains ADSL2 line PM thresholds profiles. A default profile with an index of 'DEFVAL' will always exist, and its parameters will be set to vendor- specific values, unless otherwise specified in this document. The index of this entry is adsl2LineAlarmConfProfileName.
NUM hwadsl2LineAlarmConfProfileXturThresh15MinLeftrs	1.3.6.1.4.1.2011.6.138.1.5.3.2.1.1	HCPerfIntervalThreshold	read-create	A threshold for the hwadsl2PMLCurr15MLeftrs counter, when adsl2PMLCurrUnit is ATUR {2}. The value 0 means that no threshold is specified for the associated counter. Unit: seconds
INT hwAdsl2LineAlarmConfProfileDyingGaspAlarmSwitch	1.3.6.1.4.1.2011.6.138.1.5.3.2.1.2	INTEGER	read-create	This object enable/disable the report of LOSS-OF-POWER alarm in an ADSL line. Options: 1. enable(1) - The report of LOSS-OF-POWER alarm in an ADSL line is enabled 2. disable(2) - The report of LOSS-OF-POWER alarm in an ADSL line is disabled
INT hwAdsl2LineAlarmConfProfileActiveFailAlarmSwitch	1.3.6.1.4.1.2011.6.138.1.5.3.2.1.3	INTEGER	read-create	This object enable/disable the active fail alarm switch. Options: 1. enable(1) - The active fail alarm switch is enabled 2. disable(2) - The active fail alarm switch is disabled
hwadsl2Scalar	1.3.6.1.4.1.2011.6.138.1.6
hwadsl2ScalarSC	1.3.6.1.4.1.2011.6.138.1.6.1
hwadsl2Conformance	1.3.6.1.4.1.2011.6.138.1.8
hwadsl2Mode	1.3.6.1.4.1.2011.6.138.1.9
ADS hwadslmodecfgCfg	1.3.6.1.4.1.2011.6.138.1.9.1	Adsl2CfgMode	read-write	This object is used to change ADSL management mode. After the mode being changed, system will automatically save data and reboot.
INT hwadslabrmodecfgCfg	1.3.6.1.4.1.2011.6.138.1.9.2	INTEGER	read-write	This object is used to change abr-calculation mode. Options: 1. normalMode(1) - Normal abr-calculation mode 2. ptMode(2) - PT abr-calculation mode
hwAdsl2TrapsVbOids	1.3.6.1.4.1.2011.6.138.1.10
OCT hwadsl2LinePMThresholdItem	1.3.6.1.4.1.2011.6.138.1.10.0	OCTET STRING	accessible-for-notify	Indicate the threshold item.
G32 hwadsl2LineTemplateID	1.3.6.1.4.1.2011.6.138.1.10.1	Gauge32	accessible-for-notify	Indicate line template ID.
OCT hwadsl2ActivationFailureCause	1.3.6.1.4.1.2011.6.138.1.10.2	OCTET STRING	accessible-for-notify	The reason of activation failure.
I32 hwadsl2ChipsetID	1.3.6.1.4.1.2011.6.138.1.10.3	Integer32	accessible-for-notify	The Chipset ID.
INT hwAdsl2SwitchResult	1.3.6.1.4.1.2011.6.138.1.10.4	INTEGER	accessible-for-notify	Mode switch result. Options: 1. success(0) - Indicates that the adsl mode switch result is success 2. fail(1) - Indicates that the adsl mode switch result is fail
I32 hwAdsl2RequestID	1.3.6.1.4.1.2011.6.138.1.10.5	Integer32	accessible-for-notify	Request ID.
INT hwadsl2LineCmndConfLdsfResult	1.3.6.1.4.1.2011.6.138.1.10.6	INTEGER	accessible-for-notify	The result of the test. Options: 1. success(0) - Indicates that the test result is success 2. fail(1) - Indicates that the test result is fail
I32 hwadsl2LinePMThresholdValue	1.3.6.1.4.1.2011.6.138.1.10.7	Integer32	accessible-for-notify	Indicate the threshold value of threshold item.
I32 hwadsl2LinePMCurrentValue	1.3.6.1.4.1.2011.6.138.1.10.8	Integer32	accessible-for-notify	Indicate the current value of threshold item.
I32 hwadsl2ChPMThresholdValue	1.3.6.1.4.1.2011.6.138.1.10.9	Integer32	accessible-for-notify	Indicate the threshold value of threshold item.
I32 hwadsl2ChPMCurrentValue	1.3.6.1.4.1.2011.6.138.1.10.10	Integer32	accessible-for-notify	Indicate the current value of threshold item.
hwadsl2Traps	1.3.6.1.4.1.2011.6.138.1.11
hwAdsl2CommonTraps	1.3.6.1.4.1.2011.6.138.1.11.1
hwAdsl2CommonTrapsPrefix	1.3.6.1.4.1.2011.6.138.1.11.1.0
NTF hwAdsl2ModeSwitchResultTrap	1.3.6.1.4.1.2011.6.138.1.11.1.0.1			Adsl2 mode switch result trap. This trap message is generated when the result of the recent ADSL mode switch process.
NTF hwAdsl2AdminModeTrap	1.3.6.1.4.1.2011.6.138.1.11.1.0.2			Adsl2 administration mode trap. This trap message is generated when the ADSL mode is the system worked.
NTF hwAdsl2DeltOperResultTrap	1.3.6.1.4.1.2011.6.138.1.11.1.0.3			NGADSL delt trap. This trap message is generated when delt test result reported.
NTF hwAdsl2PortStatusChangeTrap	1.3.6.1.4.1.2011.6.138.1.11.1.0.4			Adsl2 port status change trap. This trap message is generated when port status changes.
hwadsl2AlarmTraps	1.3.6.1.4.1.2011.6.138.1.11.2
hwadsl2AlarmTrapsPrefix	1.3.6.1.4.1.2011.6.138.1.11.2.0
NTF hwadsl2PortAutoDeactiveAlarmTrap	1.3.6.1.4.1.2011.6.138.1.11.2.0.0			Port automatically trap. This trap message is generated when the ADSL port is automatically deactivated. The ADSL port is automatically deactivated due to the line fault.
NTF hwAdsl2PortReactiveAlarmTrap	1.3.6.1.4.1.2011.6.138.1.11.2.0.1			Port reactive trap. This trap message is generated when the ADSL port is re-activated after the ADSL line recovers.
NTF hwAdsl2PortATURPowerOffAlarmTrap	1.3.6.1.4.1.2011.6.138.1.11.2.0.2			Port ATU-R power off trap. This trap message is generated when ATU-R is powered off.
NTF hwAdsl2ChipsetRecoverAlarmTrap	1.3.6.1.4.1.2011.6.138.1.11.2.0.3			Chipset recover trap. This trap message is generated when the ADSL chipset recovers.
NTF hwAdsl2PortDeactiveAlarmTrap	1.3.6.1.4.1.2011.6.138.1.11.2.0.4			Port deactive trap. This trap message is generated when some xDSL ports or all the xDSL ports are automatically deactivated. Some xDSL ports or all the xDSL ports are automatically deactivated due to lack of licenses.
NTF hwAdsl2LinePerformanceStatAlarmTrap	1.3.6.1.4.1.2011.6.138.1.11.2.0.5			Line performance statistics trap. This trap message is generated when the line performance statistics of the ADSL port reach the threshold.
NTF hwAdsl2DownstreamActivationRateAlarmTrap	1.3.6.1.4.1.2011.6.138.1.11.2.0.6			ADSL channel downstream activation rate trap. This trap message is generated when the ADSL channel downstream activation rate is lower than the threshold.
NTF hwAdsl2ChannelPerformanceStatAlarmTrap	1.3.6.1.4.1.2011.6.138.1.11.2.0.7			Channel performance statistics trap. This trap message is generated when the channel performance statistics of the ADSL port reach the threshold.
NTF hwAdsl2UpstreamActivationRateAlarmTrap	1.3.6.1.4.1.2011.6.138.1.11.2.0.8			ADSL channel upstream activation rate trap. This trap message is generated when the ADSL channel upstream activation rate is lower than the threshold.
NTF hwAdsl2UpstreamRateIncreaseAlarmTrap	1.3.6.1.4.1.2011.6.138.1.11.2.0.9			ADSL channel upstream rate increases trap. This trap message is generated when the ADSL channel upstream rate increases to a value higher than the threshold.
NTF hwAdsl2UpstreamRateDecreaseAlarmTrap	1.3.6.1.4.1.2011.6.138.1.11.2.0.10			ADSL channel upstream rate decreases trap. This trap message is generated when the ADSL channel upstream rate decreases to a value lower than the threshold.
NTF hwAdsl2DownstreamRateIncreaseAlarmTrap	1.3.6.1.4.1.2011.6.138.1.11.2.0.11			ADSL channel downstream rate increases trap. This trap message is generated when the ADSL channel downstream rate increases to a value higher than the threshold.
NTF hwAdsl2DownstreamRateDecreaseAlarmTrap	1.3.6.1.4.1.2011.6.138.1.11.2.0.12			ADSL channel downstream rate decreases trap. This trap message is generated when the ADSL channel downstream rate decreases to a value lower than the threshold.
NTF hwAdsl2FailedActiveAlarmTrap	1.3.6.1.4.1.2011.6.138.1.11.2.0.13			Failed active trap. This trap message is generated when it failed to activate the port using the ADSL line configuration parameters.
NTF hwAdsl2ChipsetNotAvailableAlarmTrap	1.3.6.1.4.1.2011.6.138.1.11.2.0.14			Chipset not available trap. This trap message is generated when the ADSL chipset is not available.

RFC description

Huawei ADSL2 line management extending RFC 4706, monitoring DSL port status, performance, and configuration.

Start monitoring Huawei DSLAM/MSAN broadband access equipment (Next-Generation ADSL2/ADSL2+) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HUAWEI-NGADSL-LINE-MIB

What Is HUAWEI-NGADSL-LINE-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description