All MIBs › ADTRAN-ACTDAXL3-MIB
Category: DSL and Broadband, Vendor: ADTRAN
Description: Manages Layer 3 routing features of ADTRAN ACTDAX DSL access devices including IP routing and WAN interface configuration.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is ADTRAN-ACTDAXL3-MIB?
ADTRAN-ACTDAXL3-MIB is a vendor-specific MIB for ADTRAN's ACTDAX DSL access product line, covering Layer 3 routing features such as IP routing configuration and WAN interface setup on these DSL access devices. No module description or sample objects were supplied in the source, so exact object names cannot be confirmed, but by its stated scope this MIB would be used to monitor the software/routing status of the device, such as whether IP routes are correctly configured and whether WAN interfaces are up and passing traffic, rather than pure hardware sensors. It likely depends on standard IETF routing/interface MIBs (e.g. IF-MIB, IP-MIB) for baseline conventions given its Layer 3 routing focus. It is typically deployed on ADTRAN ACTDAX DSL access equipment used by carriers/ISPs to provide routed DSL access service to business or residential customers. Engineers can download the ADTRAN-ACTDAXL3-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in ADTRAN-ACTDAXL3-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- ADTRAN ACTDAX DSL access device
Monitoring Examples
No sample objects were available for this module, so no specific object or table names can be cited. Typically an operator would poll WAN interface operational status and IP routing table entries to detect a DSL access device with a down WAN link or a missing/incorrect route affecting customer connectivity. This remains a general description since the underlying object identifiers were not supplied in the source.
What Can Be Monitored
- WAN interface status
- IP routing configuration
- Layer 3 routing state
This MIB depends on
Related MIBs
Imported Objects
From ADTRAN-MIB
| adProdPhysAddress | OBJECT-TYPE |
From RFC-1212
| OBJECT-TYPE |
From RFC-1215
| TRAP-TYPE |
From RFC1155-SMI
| Gauge | |
| enterprises |
From RFC1213-MIB
| DisplayString |
From RFC1406-MIB
| dsx1LineIndex | OBJECT-TYPE |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| adACTDAXL3 | 1.3.6.1.4.1.664.1.9 | |||
| NTF adACTDAXL3bankAlarm | 1.3.6.1.4.1.664.1.9.0.937 | This trap indicates that the ACT 1241 bank is in alarm. | ||
| NTF adACTDAXL3bankAlarmClear | 1.3.6.1.4.1.664.1.9.0.936 | This trap indicates that a ACT 1241 bank has cleared. | ||
| NTF adACTDAXL3CurrentBES | 1.3.6.1.4.1.664.1.9.0.977 | This trap indicates that the current interval Bursty Errored Seconds threshold has been exceeded on the specified ds1 line. | ||
| NTF adACTDAXL3CurrentCSS | 1.3.6.1.4.1.664.1.9.0.974 | This trap indicates that the current interval Controlled Slip Seconds threshold has been exceeded on the specified ds1 line. | ||
| NTF adACTDAXL3CurrentES | 1.3.6.1.4.1.664.1.9.0.970 | This trap indicates that the current interval Errored Seconds threshold has been exceeded on the specified ds1 line. | ||
| NTF adACTDAXL3CurrentLCV | 1.3.6.1.4.1.664.1.9.0.979 | This trap indicates that the current interval Line Code Violations threshold has been exceeded on the specified ds1 line. | ||
| NTF adACTDAXL3CurrentLES | 1.3.6.1.4.1.664.1.9.0.976 | This trap indicates that the current interval Line Errored Seconds threshold has been exceeded on the specified ds1 line. | ||
| NTF adACTDAXL3CurrentPCV | 1.3.6.1.4.1.664.1.9.0.975 | This trap indicates that the current interval Path Code Violations threshold has been exceeded on the specified ds1 line. | ||
| NTF adACTDAXL3CurrentSEFS | 1.3.6.1.4.1.664.1.9.0.972 | This trap indicates that the current interval Severely Errored Framing Seconds threshold has been exceeded on the specified ds1 line. | ||
| NTF adACTDAXL3CurrentSES | 1.3.6.1.4.1.664.1.9.0.971 | This trap indicates that the current interval Severely Errored Seconds threshold has been exceeded on the specified ds1 line. | ||
| NTF adACTDAXL3CurrentUAS | 1.3.6.1.4.1.664.1.9.0.973 | This trap indicates that the current interval Unavailable Seconds threshold has been exceeded on the specified ds1 line. | ||
| NTF adACTDAXL3DailyBES | 1.3.6.1.4.1.664.1.9.0.967 | This trap indicates that the daily (total) interval Bursty Errored Seconds threshold has been exceeded on the specified ds1 line. | ||
| NTF adACTDAXL3DailyCSS | 1.3.6.1.4.1.664.1.9.0.964 | This trap indicates that the daily (total) interval Controlled Slip Seconds threshold has been exceeded on the specified ds1 line. | ||
| NTF adACTDAXL3DailyES | 1.3.6.1.4.1.664.1.9.0.960 | This trap indicates that the daily (total) interval Errored Seconds threshold has been exceeded on the specified ds1 line. | ||
| NTF adACTDAXL3DailyLCV | 1.3.6.1.4.1.664.1.9.0.969 | This trap indicates that the daily (total) interval Line Code Violations threshold has been exceeded on the specified ds1 line. | ||
| NTF adACTDAXL3DailyLES | 1.3.6.1.4.1.664.1.9.0.966 | This trap indicates that the daily (total) interval Line Errored Seconds threshold has been exceeded on the specified ds1 line. | ||
| NTF adACTDAXL3DailyPCV | 1.3.6.1.4.1.664.1.9.0.965 | This trap indicates that the daily (total) interval Path Code Violations threshold has been exceeded on the specified ds1 line. | ||
| NTF adACTDAXL3DailySEFS | 1.3.6.1.4.1.664.1.9.0.962 | This trap indicates that the daily (total) interval Severely Errored Framing Seconds threshold has been exceeded on the specified ds1 line. | ||
| NTF adACTDAXL3DailySES | 1.3.6.1.4.1.664.1.9.0.961 | This trap indicates that the daily (total) interval Severely Errored Seconds threshold has been exceeded on the specified ds1 line. | ||
| NTF adACTDAXL3DailyUAS | 1.3.6.1.4.1.664.1.9.0.963 | This trap indicates that the daily (total) interval Unavailable Seconds threshold has been exceeded on the specified ds1 line. | ||
| NTF adACTDAXL3FarCurrentBES | 1.3.6.1.4.1.664.1.9.0.997 | This trap indicates that the far end current interval Bursty Errored Seconds threshold has been exceeded on the specified ds1 line. | ||
| NTF adACTDAXL3FarCurrentCSS | 1.3.6.1.4.1.664.1.9.0.994 | This trap indicates that the far end current interval Controlled Slip Seconds threshold has been exceeded on the specified ds1 line. | ||
| NTF adACTDAXL3FarCurrentES | 1.3.6.1.4.1.664.1.9.0.990 | This trap indicates that the far end current interval Errored Seconds threshold has been exceeded on the specified ds1 line. | ||
| NTF adACTDAXL3FarCurrentLES | 1.3.6.1.4.1.664.1.9.0.996 | This trap indicates that the far end current interval Line Errored Seconds threshold has been exceeded on the specified ds1 line. | ||
| NTF adACTDAXL3FarCurrentPCV | 1.3.6.1.4.1.664.1.9.0.995 | This trap indicates that the far end current interval Path Code Violations threshold has been exceeded on the specified ds1 line. | ||
| NTF adACTDAXL3FarCurrentSEFS | 1.3.6.1.4.1.664.1.9.0.992 | This trap indicates that the far end current interval Severely Errored Framing Seconds threshold has been exceeded on the specified ds1 line. | ||
| NTF adACTDAXL3FarCurrentSES | 1.3.6.1.4.1.664.1.9.0.991 | This trap indicates that the far end current interval Severely Errored Seconds threshold has been exceeded on the specified ds1 line. | ||
| NTF adACTDAXL3FarCurrentUAS | 1.3.6.1.4.1.664.1.9.0.993 | This trap indicates that the far end current interval Unavailable Seconds threshold has been exceeded on the specified ds1 line. | ||
| NTF adACTDAXL3FarDailyBES | 1.3.6.1.4.1.664.1.9.0.987 | This trap indicates that the far end daily (total) interval Bursty Errored Seconds threshold has been exceeded on the specified ds1 line. | ||
| NTF adACTDAXL3FarDailyCSS | 1.3.6.1.4.1.664.1.9.0.984 | This trap indicates that the far end daily (total) interval Controlled Slip Seconds threshold has been exceeded on the specified ds1 line. | ||
| NTF adACTDAXL3FarDailyES | 1.3.6.1.4.1.664.1.9.0.980 | This trap indicates that the far end daily (total) interval Errored Seconds threshold has been exceeded on the specified ds1 line. | ||
| NTF adACTDAXL3FarDailyLES | 1.3.6.1.4.1.664.1.9.0.986 | This trap indicates that the far end daily (total) interval Line Errored Seconds threshold has been exceeded on the specified ds1 line. | ||
| NTF adACTDAXL3FarDailyPCV | 1.3.6.1.4.1.664.1.9.0.985 | This trap indicates that the far end daily (total) interval Path Code Violations threshold has been exceeded on the specified ds1 line. | ||
| NTF adACTDAXL3FarDailySEFS | 1.3.6.1.4.1.664.1.9.0.982 | This trap indicates that the far end daily (total) interval Severely Errored Framing Seconds threshold has been exceeded on the specified ds1 line. | ||
| NTF adACTDAXL3FarDailySES | 1.3.6.1.4.1.664.1.9.0.981 | This trap indicates that the far end daily (total) interval Severely Errored Seconds threshold has been exceeded on the specified ds1 line. | ||
| NTF adACTDAXL3FarDailyUAS | 1.3.6.1.4.1.664.1.9.0.983 | This trap indicates that the far end daily (total) interval Unavailable Seconds threshold has been exceeded on the specified ds1 line. | ||
| NTF adACTDAXL3farLineLoop | 1.3.6.1.4.1.664.1.9.0.933 | This trap indicates that the far end has been commanded into a line loopback from the near end through the facility data link. | ||
| NTF adACTDAXL3farLineLoopClear | 1.3.6.1.4.1.664.1.9.0.932 | This trap indicates that the far end has cleared a line loopback which was commanded from the near end through the facility data link. | ||
| NTF adACTDAXL3farPayloadLoop | 1.3.6.1.4.1.664.1.9.0.935 | This trap indicates that the far end has been commanded into a payload loopback from the near end through the facility data link. | ||
| NTF adACTDAXL3farPayloadLoopClear | 1.3.6.1.4.1.664.1.9.0.934 | This trap indicates that the far end has cleared a payload loopback which was commanded from the near end through the facility data link. | ||
| NTF adACTDAXL3fdlLineLoop | 1.3.6.1.4.1.664.1.9.0.929 | This trap indicates that a line loopback has occured on the specified ds1 line. The line loopback was commanded from the far end through the facility data link. | ||
| NTF adACTDAXL3fdlLineLoopClear | 1.3.6.1.4.1.664.1.9.0.928 | This trap indicates that a line loopback has cleared on the specified ds1 line. The line loopback was commanded from the far end through the facility data link. | ||
| NTF adACTDAXL3fdlPayloadLoop | 1.3.6.1.4.1.664.1.9.0.931 | This trap indicates that a payload loopback has occured on the specified ds1 line. The payload loopback was commanded from the far end through the facility data link. | ||
| NTF adACTDAXL3fdlPayloadLoopClear | 1.3.6.1.4.1.664.1.9.0.930 | This trap indicates that a payload loopback has occured on the specified ds1 line. The payload loopback was commanded from the far end through the facility data link. | ||
| NTF adACTDAXL3LineLoop | 1.3.6.1.4.1.664.1.9.0.925 | This trap indicates that a line loopback has occured on the specified ds1 line. The line loopback was commanded by the hardware switch or through an administrative port. | ||
| NTF adACTDAXL3LineLoopClear | 1.3.6.1.4.1.664.1.9.0.924 | This trap indicates that a line loopback has cleared on the specified ds1 line. The line loopback was commanded by the hardware switch or through an administrative port. | ||
| NTF adACTDAXL3LocalLoop | 1.3.6.1.4.1.664.1.9.0.923 | This trap indicates that a local loopback has occured on the specified ds1 line. | ||
| NTF adACTDAXL3LocalLoopClear | 1.3.6.1.4.1.664.1.9.0.922 | This trap indicates that a local loopback has cleared on the specified ds1 line. | ||
| NTF adACTDAXL3LOS | 1.3.6.1.4.1.664.1.9.0.921 | This trap indicates that a loss of signal state has occured on the specified ds1 line. | ||
| NTF adACTDAXL3LOSclear | 1.3.6.1.4.1.664.1.9.0.920 | This trap indicates that a loss of signal state has cleared on the specified ds1 line. | ||
| adACTDAXL3mg | 1.3.6.1.4.1.664.2.9 | |||
| NTF adACTDAXL3PayloadLoop | 1.3.6.1.4.1.664.1.9.0.927 | This trap indicates that a payload loopback has occured on the specified ds1 line. The payload loopback was commanded by the hardware switch or through an administrative port. | ||
| NTF adACTDAXL3PayloadLoopClear | 1.3.6.1.4.1.664.1.9.0.926 | This trap indicates that a payload loopback has occured on the specified ds1 line. The payload loopback was commanded by the hardware switch or through an administrative port. | ||
| NTF adACTDAXL3RedAlarm | 1.3.6.1.4.1.664.1.9.0.919 | This trap indicates that a red alarm has occured on the specified ds1 line. | ||
| NTF adACTDAXL3RedAlarmClear | 1.3.6.1.4.1.664.1.9.0.918 | This trap indicates that a red alarm has cleared on the specified ds1 line. | ||
| NTF adACTDAXL3RxAIS | 1.3.6.1.4.1.664.1.9.0.915 | This trap indicates that an alarm indication signal (AIS) state has occured on the specified ds1 line. | ||
| NTF adACTDAXL3RxAISclear | 1.3.6.1.4.1.664.1.9.0.914 | This trap indicates that an alarm indication signal (AIS) state has cleared on the specified ds1 line. | ||
| NTF adACTDAXL3RxYellow | 1.3.6.1.4.1.664.1.9.0.911 | This trap indicates that yellow alarm is being received on the specified ds1 line. | ||
| NTF adACTDAXL3RxYellowClear | 1.3.6.1.4.1.664.1.9.0.910 | This trap indicates that a yellow alarm state has cleared on the specified ds1 line. | ||
| NTF adACTDAXL3systemHdwFailure | 1.3.6.1.4.1.664.1.9.0.907 | This trap indicates that a system hardware failure has occured on the ACT DAX. | ||
| NTF adACTDAXL3systemHdwFailureClear | 1.3.6.1.4.1.664.1.9.0.906 | This trap indicates that a system hardware failure has cleared on the ACT DAX. | ||
| NTF adACTDAXL3systemSfwFailure | 1.3.6.1.4.1.664.1.9.0.909 | This trap indicates that a system software failure has occured on the ACT DAX. | ||
| NTF adACTDAXL3systemSfwFailureClear | 1.3.6.1.4.1.664.1.9.0.908 | This trap indicates that a system software failure has cleared on the ACT DAX. | ||
| NTF adACTDAXL3TxAIS | 1.3.6.1.4.1.664.1.9.0.917 | This trap indicates that an alarm indication signal (AIS) is being transmitted on the specifed ds1 line. | ||
| NTF adACTDAXL3TxAISclear | 1.3.6.1.4.1.664.1.9.0.916 | This trap indicates that an alarm indication signal (AIS) is no longer being transmitted on the specified ds1 line. | ||
| NTF adACTDAXL3TxYellow | 1.3.6.1.4.1.664.1.9.0.913 | This trap indicates that a yellow alarm signal is being transmitted on the specifed ds1 line. | ||
| NTF adACTDAXL3TxYellowClear | 1.3.6.1.4.1.664.1.9.0.912 | This trap indicates that a yellow alarm signal is no longer being transmitted on the specified ds1 line. | ||
| INT adDAX3AlarmEnable | 1.3.6.1.4.1.664.2.9.6.2 | INTEGER | read-write | This bit map variable arms or disarms an individual or group of events identified in adDAX3AlarmStatus as a source for generation of System Alarm Trap. The various arm event bit positions are: 1 System Hardware Failure 2 System Software Failure 4 Channel Bank Out Of Service |
| INT adDAX3AlarmStatus | 1.3.6.1.4.1.664.2.9.6.1 | INTEGER | read-only | This bit map variable indicates alarm status for the ACTDAX and the ACT 1241 channel bank. This item does not include DS1 line status. The various alarm event bit positions are: 1 System Hardware Failure 2 System Software Failure 4 Channel Bank Out Of Service |
| INT adDAX3auditProgCode | 1.3.6.1.4.1.664.2.9.2.6 | INTEGER | read-only | A Get performs an audit of the units Program Code and returns the result as PASS or FAIL. |
| INT adDAX3backupTiming | 1.3.6.1.4.1.664.2.9.2.10 | INTEGER | read-write | The Backup Facility Timing for the ACT 1241 and the ACTDAX. The backup timing is only used if the adDAX3primaryTiming is either 'loopA' or 'loopB'. 'local' indicates that if the DS1 line fails, which is the primary timing source, then the ACTDAX will time to a local free-running oscillator. 'loop' indicates that if the DS1 line fails, which is the primary timing source, then the ACTDAX will time to the other DS1 line. If both DS1 lines fail then the ACTDAX will time to a local free-running oscillator. |
| INT adDAX3chanNumber | 1.3.6.1.4.1.664.2.9.3.1.1 | INTEGER | read-only | The channel number of this table entry |
| STR adDAX3chanUnit | 1.3.6.1.4.1.664.2.9.3.1.2 | DisplayString | read-only | The unit name plugged into this channel slot, for example, DSUDP |
| adDAX3config | 1.3.6.1.4.1.664.2.9.2 | |||
| adDAX3connEntry | 1.3.6.1.4.1.664.2.9.4.1 | not-accessible | An entry in the ACTDAX cross-connect matrix table. | |
| adDAX3connMapEntry | 1.3.6.1.4.1.664.2.9.5.1 | not-accessible | An entry in the ACTDAX cross-connect map table. | |
| adDAX3connMapTable | 1.3.6.1.4.1.664.2.9.5 | not-accessible | The ACTDAX cross-connect map table. | |
| adDAX3connTable | 1.3.6.1.4.1.664.2.9.4 | not-accessible | The ACTDAX cross-connect matrix table. | |
| INT adDAX3CurrentAlert | 1.3.6.1.4.1.664.2.9.7.1.4 | INTEGER | read-only | This DS1 performance status variable indicates Threshold Crossing Alerts for Near End Current 15 minute interval. An alert bit is set in this variable when the value of the dsx1CurrentTable object exceeds the Threshold Value. This variable contains the sum of alert values. Threshold Crossing Alert bit position values: 1 ES - Errored Seconds 2 SES - Severely Errored Seconds 4 SEFS - Severely Errored Framing Seconds 8 UAS - Unavailable Seconds 16 CSS - Controlled Slip Seconds 32 PCV - Path Coding Violations 64 LES - Line Errored Seconds 128 BES - Bursty Errored Seconds 256 DM - Degraded Minutes 512 LCV - Line Code Violations |
| INT adDAX3CurrentArm | 1.3.6.1.4.1.664.2.9.7.1.8 | INTEGER | read-write | This variable arms and disarms an individual or group of alerts identified in adDAX3CurrentAlert as a source for the generation of Threshold Crossing Alert Trap. This variable contains the sum of Arm values. Threshold Crossing Arm bit position values: 1 ES - Errored Seconds 2 SES - Severely Errored Seconds 4 SEFS - Severely Errored Framing Seconds 8 UAS - Unavailable Seconds 16 CSS - Controlled Slip Seconds 32 PCV - Path Coding Violations 64 LES - Line Errored Seconds 128 BES - Bursty Errored Seconds 256 DM - Degraded Minutes 512 LCV - Line Code Violations |
| INT adDAX3CurrentThrsBES | 1.3.6.1.4.1.664.2.9.8.1.10 | INTEGER | read-write | The DS1 performance monitor Threshold Value for the Current 15 minute Bursty Errored Seconds parameter. The default value is ?? for an approximate BER level of (10** -5). |
| INT adDAX3CurrentThrsCSS | 1.3.6.1.4.1.664.2.9.8.1.6 | INTEGER | read-write | The DS1 performance monitor Threshold Value for the Current 15 minute Controlled Slip Seconds parameter. The default value is 1 for an approximate BER level of (10** -5). |
| adDAX3CurrentThrsEntry | 1.3.6.1.4.1.664.2.9.8.1 | not-accessible | An entry in the DS1 Current Threshold Table. | |
| INT adDAX3CurrentThrsES | 1.3.6.1.4.1.664.2.9.8.1.2 | INTEGER | read-write | The DS1 performance monitor Threshold Value for the Current 15 minute Errored Seconds parameter. The default value is 65 for an approximate BER level of (10** -5). |
| INT adDAX3CurrentThrsIndex | 1.3.6.1.4.1.664.2.9.8.1.1 | INTEGER | read-only | The index value which uniquely identifies the DS1 interface. The interface identified by a particular value of this index is the same interface as identified by dsx1LineIndex in DS1 MIB. |
| INT adDAX3CurrentThrsLCV | 1.3.6.1.4.1.664.2.9.8.1.11 | INTEGER | read-write | The DS1 performance monitor Threshold Value for the Current 15 minute Line Code Violations parameter. The default value is 13,340 for an approximate BER level of (10** -5). |
| INT adDAX3CurrentThrsLES | 1.3.6.1.4.1.664.2.9.8.1.9 | INTEGER | read-write | The DS1 performance monitor Threshold Value for the Current 15 minute Line Errored Seconds parameter. The default value is 65 for an approximate BER level of (10** -5). |
| INT adDAX3CurrentThrsPCVesf | 1.3.6.1.4.1.664.2.9.8.1.8 | INTEGER | read-write | The DS1 performance monitor Threshold Value for the Current 15 minute Path Coding Violations parameter, when the Line Type is Extended Super Frame (ESF) DS1. Default value for an approximate BER level of (10**-5) is 13,296 CRC errors. |
| INT adDAX3CurrentThrsPCVsf | 1.3.6.1.4.1.664.2.9.8.1.7 | INTEGER | read-write | The DS1 performance monitor Threshold Value for the Current 15 minute Path Coding Violations parameter, when the Line Type is Super Frame (AT&T D4 format) DS1. Default value for an approximate BER level of (10**-5) is 72 Framing errors. |
| INT adDAX3CurrentThrsSEFS | 1.3.6.1.4.1.664.2.9.8.1.4 | INTEGER | read-write | The DS1 performance monitor Threshold Value for the Current 15 minute Severely Errored Framing Seconds parameter. The default value is 2 for an approximate BER level of (10** -5). |
| INT adDAX3CurrentThrsSES | 1.3.6.1.4.1.664.2.9.8.1.3 | INTEGER | read-write | The DS1 performance monitor Threshold Value for the Current 15 minute Severely Errored Seconds parameter. The default value is 10 for an approximate BER level of (10** -5). |
| adDAX3CurrentThrsTable | 1.3.6.1.4.1.664.2.9.8 | not-accessible | The DS1 Current Threshold Table. | |
| INT adDAX3CurrentThrsUAS | 1.3.6.1.4.1.664.2.9.8.1.5 | INTEGER | read-write | The DS1 performance monitor Threshold Value for the Current 15 minute Unavailable Seconds parameter. The default value is 10 for an approximate BER level of (10** -5). |
| INT adDAX3daisyChain | 1.3.6.1.4.1.664.2.9.2.25 | INTEGER | read-write | Disable/Enable the Local Rear Panel Port of the ACTDAX for Daisy Chain operation. 'off' indicates that the Local Rear Panel Port will run the EASYMENU terminal interface. 'on' indicates that the Local Rear Panel Port can be connected to the remote port of the next unit downstream from the proxy agent. |
| STR adDAX3date | 1.3.6.1.4.1.664.2.9.2.4 | DisplayString | read-write | The current ACTDAX date value. A sequence of ASCII characters encoded as MM/DD/YY. For example, April 28, 1994 is 04/28/94. |
| STR adDAX3device_2 | 1.3.6.1.4.1.664.2.9.3.1.3 | DisplayString | read-only | The device name of the PM loop unit connected to the channel unit, for example, LR-IV |
| STR adDAX3device_3 | 1.3.6.1.4.1.664.2.9.3.1.4 | DisplayString | read-only | The device name of the PM loop unit connected to a secondary loop, for example, DDST-IV |
| STR adDAX3device_4 | 1.3.6.1.4.1.664.2.9.3.1.5 | DisplayString | read-only | The device name of the PM loop unit connected to a secondary loop, for example, DDST-IV |
| STR adDAX3device_5 | 1.3.6.1.4.1.664.2.9.3.1.6 | DisplayString | read-only | The device name of the PM loop unit connected to a secondary loop, for example, DDST-IV |
| INT adDAX3deviceAddress | 1.3.6.1.4.1.664.2.9.2.2 | INTEGER | read-only | The device address for this ACTDAX. The device address is used to access the device from the proxy agent. |
| INT adDAX3ds1AlineEqlz | 1.3.6.1.4.1.664.2.9.2.11 | INTEGER | read-write | The DS1 Line A transmit pre-equalizer circuitry provisioning for conditioning the T1 output signal for connection to a CSU, other customer premises equipment, or the DSX-1 cross-connect through various cable lengths between 0 and 655 feet. '0-110' indicates 0-110 feet. '110-220' indicates 110-220 feet. '220-330' indicates 220-330 feet. '330-440' indicates 330-440 feet. '440-550' indicates 440-550 feet. '550-655' indicates 550-655 feet. |
| INT adDAX3ds1Aoperation | 1.3.6.1.4.1.664.2.9.2.13 | INTEGER | read-write | The DS1 Line A Operational Status. 'disabled' turns off the faceplate indicators for DS1 A, disables EASY-MENU alarmsfor DS1 A, and stops data transmission for DS1 A. 'enabled' reverses the effect of 'disabled'. |
| INT adDAX3ds1BlineEqlz | 1.3.6.1.4.1.664.2.9.2.12 | INTEGER | read-write | The DS1 Line B transmit pre-equalizer circuitry provisioning for conditioning the T1 output signal for connection to a CSU, other customer premises equipment, or the DSX-1 cross-connect through various cable lengths between 0 and 655 feet. '0-110' indicates 0-110 feet. '110-220' indicates 110-220 feet. '220-330' indicates 220-330 feet. '330-440' indicates 330-440 feet. '440-550' indicates 440-550 feet. '550-655' indicates 550-655 feet. |
| INT adDAX3ds1Boperation | 1.3.6.1.4.1.664.2.9.2.14 | INTEGER | read-write | The DS1 Line B Operational Status. 'disabled' turns off the faceplate indicators for DS1 B, disables EASY-MENU alarmsfor DS1 B, and stops data transmission for DS1 B. 'enabled' reverses the effect of 'disabled'. |
| adDAX3ds1EventEntry | 1.3.6.1.4.1.664.2.9.7.1 | not-accessible | An entry in the DS1 Alarm/Alert Event Table. | |
| INT adDAX3ds1EventIndex | 1.3.6.1.4.1.664.2.9.7.1.1 | INTEGER | read-only | The index value which uniquely identifies the DS1 interface. The interface identified by a particular value of this index is the same interface as identified by dsx1LineIndex in DS1 MIB. |
| adDAX3ds1EventTable | 1.3.6.1.4.1.664.2.9.7 | not-accessible | The DS1 Alarm/Alert Event Table. | |
| INT adDAX3FarCurrentAlert | 1.3.6.1.4.1.664.2.9.7.1.6 | INTEGER | read-only | This DS1 performance status variable indicates Threshold Crossing Alerts for Far End Current 15 minute interval. An alert bit is set in this variable when the value of the dsx1FarEndCurrentTable object exceeds the Threshold Value. This variable contains the sum of alert values. Threshold Crossing Alert bit position values: 1 ES - Errored Seconds 2 SES - Severely Errored Seconds 4 SEFS - Severely Errored Framing Seconds 8 UAS - Unavailable Seconds 16 CSS - Controlled Slip Seconds 32 PCV - Path Coding Violations 64 LES - Line Errored Seconds 128 BES - Bursty Errored Seconds 256 DM - Degraded Minutes |
| INT adDAX3FarCurrentArm | 1.3.6.1.4.1.664.2.9.7.1.10 | INTEGER | read-write | This variable arms and disarms an individual or group of alerts identified in adDAX3FarCurrentAlert as a source for the generation of Threshold Crossing Alert Trap. This variable contains the sum of Arm values. Threshold Crossing Arm bit position values: 1 ES - Errored Seconds 2 SES - Severely Errored Seconds 4 SEFS - Severely Errored Framing Seconds 8 UAS - Unavailable Seconds 16 CSS - Controlled Slip Seconds 32 PCV - Path Coding Violations 64 LES - Line Errored Seconds 128 BES - Bursty Errored Seconds 256 DM - Degraded Minutes |
| INT adDAX3FarTotalAlert | 1.3.6.1.4.1.664.2.9.7.1.7 | INTEGER | read-only | This DS1 performance status variable indicates Threshold Crossing Alerts for Far End Total performance variables. An alert bit is set in this variable when the value of the dsx1FarEndTotalTable object exceeds the Threshold Value. This variable contains the sum of alert values. Threshold Crossing Alert bit position values: 1 ES - Errored Seconds 2 SES - Severely Errored Seconds 4 SEFS - Severely Errored Framing Seconds 8 UAS - Unavailable Seconds 16 CSS - Controlled Slip Seconds 32 PCV - Path Coding Violations 64 LES - Line Errored Seconds 128 BES - Bursty Errored Seconds 256 DM - Degraded Minutes |
| INT adDAX3FarTotalArm | 1.3.6.1.4.1.664.2.9.7.1.11 | INTEGER | read-write | This variable arms and disarms an individual or group of alerts identified in adDAX3FarTotalAlert as a source for the generation of Threshold Crossing Alert Trap. This variable contains the sum of Arm values. Threshold Crossing Arm bit position values: 1 ES - Errored Seconds 2 SES - Severely Errored Seconds 4 SEFS - Severely Errored Framing Seconds 8 UAS - Unavailable Seconds 16 CSS - Controlled Slip Seconds 32 PCV - Path Coding Violations 64 LES - Line Errored Seconds 128 BES - Bursty Errored Seconds 256 DM - Degraded Minutes |
| INT adDAX3LedStatus | 1.3.6.1.4.1.664.2.9.6.5 | INTEGER | read-only | This variable contains bit encoded values for the ACTDAX LED status: 1 RLBK-A (1=off, 0=yellow) 2 ESF-A (1=off, 0=green) 4 B8ZS-A (1=off, 0=green) 8 RLBK-B (1=off, 0=yellow) 16 ESF-B (1=off, 0=green) 32 B8ZS-B (1=off, 0=green) 64 TEST (1=off, 0=yellow) 128 unused 256 DS1-A combine with next bit 512 (00=off, 01=red, 10=green, 11=yellow) 1024 DS1-B combine with next bit 2048 (00=off, 01=red, 10=green, 11=yellow) 4096 STAT combine with next bit 8192 (00=off, 01=red, 10=green) 16384 DS0-PM combine with next bit 32768 (00=off, 01=red, 10=green). |
| INT adDAX3LineArm | 1.3.6.1.4.1.664.2.9.7.1.3 | INTEGER | read-write | This bit map variable arms or disarms an individual or group of events identified in adDAX3LineStatus as a source for generation of DS1 Alarm Trap. The various arm event bit positions are: 1 Far end LOF ( a.k.a., Yellow Alarm ) 2 Near end sending LOF Indication 4 Far end sending AIS ( Blue Alarm ) 8 Near end sending AIS 16 Near end LOF ( a.k.a., Red Alarm ) 32 Near end Loss Of Signal 64 Near end Local Loopback 128 Near end Line Loopback 256 Near end Payload Loopback 512 Far end Requested Line Loopback 1024 Far end Requested Payload Loopback 2048 Far end in Line Loopback (commanded from near end) 4096 Far end in Payload Loopback (commanded from near end) |
| INT adDAX3LineStatus | 1.3.6.1.4.1.664.2.9.7.1.2 | INTEGER | read-only | This bit map variable indicates both alarm and loopback status for the DS1 Line. The various alarm event bit positions are: 1 Far end LOF ( a.k.a., Yellow Alarm ) 2 Near end sending LOF Indication 4 Far end sending AIS ( Blue Alarm ) 8 Near end sending AIS 16 Near end LOF ( a.k.a., Red Alarm ) 32 Near end Loss Of Signal 64 Near end Local Loopback 128 Near end Line Loopback 256 Near end Payload Loopback 512 Far end Requested Line Loopback 1024 Far end Requested Payload Loopback 2048 Far end in Line Loopback (commanded from near end) 4096 Far end in Payload Loopback (commanded from near end) |
| STR adDAX3mdmDialCmd | 1.3.6.1.4.1.664.2.9.2.21 | DisplayString | read-write | The modem dialing command string. The dialing command will be sent to the modem before the phone number. Maximum of 15 characters. The factory default is 'ATDT'. |
| STR adDAX3mdmDialCmdSfx | 1.3.6.1.4.1.664.2.9.2.22 | DisplayString | read-write | The modem dialing command suffix. The dialing command suffix will be sent to the modem after the phone number. Maximum of 5 characters. Any control character should be entered as '^' plus the character. The factory default is '^M'. |
| STR adDAX3mdmHangUpCmd | 1.3.6.1.4.1.664.2.9.2.23 | DisplayString | read-write | The modem hang-up command. The hang-up command will be sent to the modem to hang-up the line. Maximum of 15 characters. Any control character should be entered as '^' plus the character. The first three characters should be the escape code sequence for the modem. The factory default is '+++ATH^M'. |
| INT adDAX3mdmInit | 1.3.6.1.4.1.664.2.9.2.24 | INTEGER | read-write | A Set will send the modem initialization string to the modem connected to the remote port. This WILL DISRUPT communications to this device. |
| STR adDAX3mdmInitCmd | 1.3.6.1.4.1.664.2.9.2.20 | DisplayString | read-write | The modem initialization command string. The initialization string will be sent to the modem on unit power-up, before a call is made, and on user command. Maximum of 40 characters. Any control character should be entered as '^' plus the character. The factory default is 'ATE0Q0V1X4&C1&D2S0=1^M'. |
| STR adDAX3password | 1.3.6.1.4.1.664.2.9.2.1 | DisplayString | read-write | The password string used for authentication of SNMP messages between Proxy Agent and ACTDAX. Maximum of 12 characters. The factory default is 'PASSWORD'. This password is NOT the same as either the read-only or read/write passwords for the EASYMENU terminal interface. |
| STR adDAX3phone | 1.3.6.1.4.1.664.2.9.2.19 | DisplayString | read-write | The dialing sequence (phone number) to reach the network manager. Maximum of 35 characters. |
| INT adDAX3primaryTiming | 1.3.6.1.4.1.664.2.9.2.9 | INTEGER | read-write | The Primary Facility Timing for the ACT 1241 and the ACTDAX. The timing set on the ACT OIU must match the timing set on the ACT DAX. 'localOrExternal' indicates that the ACTDAX is timed either a local free-running oscillator or frequency locked to an external clock signal. 'loopA' indicates that the ACTDAX is frequency locked to the received DS1 A line signal. 'loopB' indicates that the ACTDAX is frequency locked to the received DS1 B line signal. |
| INT adDAX3remPortBaudRate | 1.3.6.1.4.1.664.2.9.2.16 | INTEGER | read-write | The ACTDAX Remote Port Baud Rate. Changing the remote port buad rate WILL TERMINATE communications to this device at the current baud rate. |
| INT adDAX3remPortConnect | 1.3.6.1.4.1.664.2.9.2.18 | INTEGER | read-write | The ACTDAX Remote Port Connection Type. Changing the connection type may disrupt communication to this device. 'direct' indicates a direct connection to the proxy agent. 'dialUp' indicates a dial-Up connection to the proxy agent. The adDAX3phone should be set. |
| INT adDAX3remPortProtocol | 1.3.6.1.4.1.664.2.9.2.17 | INTEGER | read-only | The ACTDAX Remote Port Protocol. |
| INT adDAX3resetFactoryConfig | 1.3.6.1.4.1.664.2.9.2.8 | INTEGER | read-write | A Set resets ALL provisioning to the factory defaults. |
| INT adDAX3resetPM | 1.3.6.1.4.1.664.2.9.2.5 | INTEGER | read-write | Resets Performance Monitor DS1 statistic counters in ACTDAX. Parameter value 1 resets all lines, 2 resets line 1 (DS1-A), 3 resets line 2 (DS1-B). |
| INT adDAX3selfTestAndRestart | 1.3.6.1.4.1.664.2.9.2.7 | INTEGER | read-write | A Set restarts ACTDAX and performs unit self-test. Results of last unit self-test are shown as PASS or FAIL. |
| INT adDAX3sysAlarm | 1.3.6.1.4.1.664.2.9.6.3 | INTEGER | read-only | This item can be polled to determine if there are any active alarms on the ACTDAX or its corresponding intelligent units. |
| INT adDAX3sysAlarmEnable | 1.3.6.1.4.1.664.2.9.6.4 | INTEGER | read-write | This is a global enable/disable for all enterprise traps from this node controller. |
| adDAX3systemEvent | 1.3.6.1.4.1.664.2.9.6 | |||
| STR adDAX3time | 1.3.6.1.4.1.664.2.9.2.3 | DisplayString | read-write | The current ACTDAX time value. A sequence of ASCII characters encoded as HH:MM:SS. For example, 1:15 pm is 13:15:00. |
| INT adDAX3TotalAlert | 1.3.6.1.4.1.664.2.9.7.1.5 | INTEGER | read-only | This DS1 performance status variable indicates Threshold Crossing Alerts for Near End Total performance variables. An alert bit is set in this variable when the value of the dsx1TotalTable object exceeds the Threshold Value. This variable contains the sum of alert values. Threshold Crossing Alert bit position values: 1 ES - Errored Seconds 2 SES - Severely Errored Seconds 4 SEFS - Severely Errored Framing Seconds 8 UAS - Unavailable Seconds 16 CSS - Controlled Slip Seconds 32 PCV - Path Coding Violations 64 LES - Line Errored Seconds 128 BES - Bursty Errored Seconds 256 DM - Degraded Minutes 512 LCV - Line Code Violations |
| INT adDAX3TotalArm | 1.3.6.1.4.1.664.2.9.7.1.9 | INTEGER | read-write | This variable arms and disarms an individual or group of alerts identified in adDAX3TotalAlert as a source for the generation of Threshold Crossing Alert Trap. This variable contains the sum of Arm values. Threshold Crossing Arm bit position values: 1 ES - Errored Seconds 2 SES - Severely Errored Seconds 4 SEFS - Severely Errored Framing Seconds 8 UAS - Unavailable Seconds 16 CSS - Controlled Slip Seconds 32 PCV - Path Coding Violations 64 LES - Line Errored Seconds 128 BES - Bursty Errored Seconds 256 DM - Degraded Minutes 512 LCV - Line Code Violations |
| INT adDAX3TotalThrsBES | 1.3.6.1.4.1.664.2.9.9.1.10 | INTEGER | read-write | The DS1 performance monitor Threshold Value for the Total Bursty Errored Seconds parameter. The default value is ??? for an approximate BER level of (10** -5). |
| INT adDAX3TotalThrsCSS | 1.3.6.1.4.1.664.2.9.9.1.6 | INTEGER | read-write | The DS1 performance monitor Threshold Value for the Total Controlled Slip Seconds parameter. The default value is 4 for an approximate BER level of(10** -5). |
| adDAX3TotalThrsEntry | 1.3.6.1.4.1.664.2.9.9.1 | not-accessible | An entry in the DS1 Total Threshold Table. | |
| INT adDAX3TotalThrsES | 1.3.6.1.4.1.664.2.9.9.1.2 | INTEGER | read-write | The DS1 performance monitor Threshold Value for the Total Errored Seconds parameter. The default value is 648 for an approximate BER level of (10** -5). |
| INT adDAX3TotalThrsIndex | 1.3.6.1.4.1.664.2.9.9.1.1 | INTEGER | read-only | The index value which uniquely identifies the DS1 interface. The interface identified by a particular value of this index is the same interface as identified by dsx1LineIndex in DS1 MIB. |
| INT adDAX3TotalThrsLCV | 1.3.6.1.4.1.664.2.9.9.1.11 | INTEGER | read-write | The DS1 performance monitor Threshold Value for the Total Line Code Violations parameter. The default value is 133,400 for an approximate BER level of (10** -5). |
| INT adDAX3TotalThrsLES | 1.3.6.1.4.1.664.2.9.9.1.9 | INTEGER | read-write | The DS1 performance monitor Threshold Value for the Total Line Errored Seconds parameter. The default value is 648 for an approximate BER level of (10** -5). |
| INT adDAX3TotalThrsPCVesf | 1.3.6.1.4.1.664.2.9.9.1.8 | INTEGER | read-write | The DS1 performance monitor Threshold Value for the Total Path Coding Violations parameter, when the Line Type is Extended Super Frame (ESF) DS1. The default value for an approximate BER level of (10**-5) is 132,960 CRC errors. |
| INT adDAX3TotalThrsPCVsf | 1.3.6.1.4.1.664.2.9.9.1.7 | INTEGER | read-write | The DS1 performance monitor Threshold Value for the Total Path Coding Violations parameter, when the Line Type is Super Frame (AT&T D4 format) DS1. The default value for an approximate BER level of (10**-5) is 691 framing errors. |
| INT adDAX3TotalThrsSEFS | 1.3.6.1.4.1.664.2.9.9.1.4 | INTEGER | read-write | The DS1 performance monitor Threshold Value for the Total Severely Errored Framing Seconds parameter. The default value is 17 for an approximate BER level of (10** -5). |
| INT adDAX3TotalThrsSES | 1.3.6.1.4.1.664.2.9.9.1.3 | INTEGER | read-write | The DS1 performance monitor Threshold Value for the Total Severely Errored Seconds parameter. The default value is 100 for an approximate BER level of (10** -5). |
| adDAX3TotalThrsTable | 1.3.6.1.4.1.664.2.9.9 | not-accessible | The DS1 Total Threshold Table. | |
| INT adDAX3TotalThrsUAS | 1.3.6.1.4.1.664.2.9.9.1.5 | INTEGER | read-write | The DS1 performance monitor Threshold Value for the Total Unavailable Seconds parameter. The default value is 10 for an approximate BER level of (10** -5). |
| INT adDAX3trunkProcessMode | 1.3.6.1.4.1.664.2.9.2.15 | INTEGER | read-only | This item indicates how trunk processing will be initiated towards the channel units in the ACT bank in response to a DS1 alarm. This item changes based on the cross-connect matrix configuration. 'liuA' indicates that all connected digroup channels connected to DS1 Line A and are configured as full transparent connections. For an alarm on DS1 Line A the normal bank facilities for trunk conditioning and CGA code insertion will be used. 'liuB' indicates that all connected digroup channels connected to DS1 Line B and are configured as full transparent connections. For an alarm on DS1 Line B the normal bank facilities for trunk conditioning and CGA code insertion will be used. 'dax' indicates a cross connect matrix configuration other than that for 'liuA' or 'liuB'. The ACT DAX will initiate trunk processing toward all the DS0 channels in the digroup on a channel by channel basis. |
| adDAX3unit | 1.3.6.1.4.1.664.2.9.3.1 | not-accessible | ||
| adDAX3unitMap | 1.3.6.1.4.1.664.2.9.3 | not-accessible | The ACT DAX channel configuration table which shows what intelligent devices are active in each channel. | |
| INT adDAXChnl1 | 1.3.6.1.4.1.664.2.9.5.1.2 | INTEGER | read-only | The DSO channel connected to channel 1 of adDAXPort. |
| INT adDAXChnl10 | 1.3.6.1.4.1.664.2.9.5.1.11 | INTEGER | read-only | The DSO channel connected to channel 10 of adDAXPort. |
| INT adDAXChnl11 | 1.3.6.1.4.1.664.2.9.5.1.12 | INTEGER | read-only | The DSO channel connected to channel 11 of adDAXPort. |
| INT adDAXChnl12 | 1.3.6.1.4.1.664.2.9.5.1.13 | INTEGER | read-only | The DSO channel connected to channel 12 of adDAXPort. |
| INT adDAXChnl13 | 1.3.6.1.4.1.664.2.9.5.1.14 | INTEGER | read-only | The DSO channel connected to channel 13 of adDAXPort. |
| INT adDAXChnl14 | 1.3.6.1.4.1.664.2.9.5.1.15 | INTEGER | read-only | The DSO channel connected to channel 14 of adDAXPort. |
| INT adDAXChnl15 | 1.3.6.1.4.1.664.2.9.5.1.16 | INTEGER | read-only | The DSO channel connected to channel 15 of adDAXPort. |
| INT adDAXChnl16 | 1.3.6.1.4.1.664.2.9.5.1.17 | INTEGER | read-only | The DSO channel connected to channel 16 of adDAXPort. |
| INT adDAXChnl17 | 1.3.6.1.4.1.664.2.9.5.1.18 | INTEGER | read-only | The DSO channel connected to channel 17 of adDAXPort. |
| INT adDAXChnl18 | 1.3.6.1.4.1.664.2.9.5.1.19 | INTEGER | read-only | The DSO channel connected to channel 18 of adDAXPort. |
| INT adDAXChnl19 | 1.3.6.1.4.1.664.2.9.5.1.20 | INTEGER | read-only | The DSO channel connected to channel 19 of adDAXPort. |
| INT adDAXChnl2 | 1.3.6.1.4.1.664.2.9.5.1.3 | INTEGER | read-only | The DSO channel connected to channel 2 of adDAXPort. |
| INT adDAXChnl20 | 1.3.6.1.4.1.664.2.9.5.1.21 | INTEGER | read-only | The DSO channel connected to channel 20 of adDAXPort. |
| INT adDAXChnl21 | 1.3.6.1.4.1.664.2.9.5.1.22 | INTEGER | read-only | The DSO channel connected to channel 21 of adDAXPort. |
| INT adDAXChnl22 | 1.3.6.1.4.1.664.2.9.5.1.23 | INTEGER | read-only | The DSO channel connected to channel 22 of adDAXPort. |
| INT adDAXChnl23 | 1.3.6.1.4.1.664.2.9.5.1.24 | INTEGER | read-only | The DSO channel connected to channel 23 of adDAXPort. |
| INT adDAXChnl24 | 1.3.6.1.4.1.664.2.9.5.1.25 | INTEGER | read-only | The DSO channel connected to channel 24 of adDAXPort. |
| INT adDAXChnl3 | 1.3.6.1.4.1.664.2.9.5.1.4 | INTEGER | read-only | The DSO channel connected to channel 3 of adDAXPort. |
| INT adDAXChnl4 | 1.3.6.1.4.1.664.2.9.5.1.5 | INTEGER | read-only | The DSO channel connected to channel 4 of adDAXPort. |
| INT adDAXChnl5 | 1.3.6.1.4.1.664.2.9.5.1.6 | INTEGER | read-only | The DSO channel connected to channel 5 of adDAXPort. |
| INT adDAXChnl6 | 1.3.6.1.4.1.664.2.9.5.1.7 | INTEGER | read-only | The DSO channel connected to channel 6 of adDAXPort. |
| INT adDAXChnl7 | 1.3.6.1.4.1.664.2.9.5.1.8 | INTEGER | read-only | The DSO channel connected to channel 7 of adDAXPort. |
| INT adDAXChnl8 | 1.3.6.1.4.1.664.2.9.5.1.9 | INTEGER | read-only | The DSO channel connected to channel 8 of adDAXPort. |
| INT adDAXChnl9 | 1.3.6.1.4.1.664.2.9.5.1.10 | INTEGER | read-only | The DSO channel connected to channel 9 of adDAXPort. |
| INT adDAXCircuitType | 1.3.6.1.4.1.664.2.9.4.1.6 | INTEGER | read-write | The ciruit type for the connection. The ciruit type will determine the settings for adDAXSgnlState, adDAXTroubleInsert, adDAXTroubleCode, adDAXFromTC, and adDAXToTC. For voice circuit types such as 'fxo-fxs', 'fxo' represents the from channel and 'fxs' represents the to channel. 'fullTransparent' indicates SgnlState=transparent, TroubleInsert=no, FromTC=none, and ToTC=none. 'dataTransparent' indicates SgnlState=transparent, TroubleCode=9Ah, FromTC=none, and ToTC=none. 'dataSW56' indicates SgnlState=2state, TroubleCode=9Ah, FromTC=0000, ToTC=0000. 'voiceTransparent' indicates SgnlState=transparent, TroubleCode=7Fh, FromTC=none, and ToTC=none. 'dpt-dpo' indicates SgnlState=2state, TroubleCode=7Fh, FromTC=0000, ToTC=0011. 'dpo-dpt' indicates SgnlState=2state, TroubleCode=7Fh, FromTC=0011, ToTC=0000. 'fxo-fxs' indicates SgnlState=4state, TroubleCode=7Fh, FromTC=0100, ToTC=1101. 'fxs-fxo' indicates SgnlState=4state, TroubleCode=7Fh, FromTC=1101, ToTC=0100. 'em' indicates SgnlState=2state, TroubleCode=7Fh, FromTC=0011, ToTC=0011. 'plar-d3' indicates SgnlState=2state, TroubleCode=7Fh, FromTC=0000, ToTC=0000. 'plar-d4' indicates SgnlState=2state, TroubleCode=7Fh, FromTC=1111, ToTC=1111. |
| INT adDAXConnStatus | 1.3.6.1.4.1.664.2.9.4.1.3 | INTEGER | read-write | The Connection Status for the channel. 'unmapped' indicates that the channel is not connected. 'connected' indicates that the channel is connected to the channel indicated by adDAXToPort and adDAXToChannel with the attributes defined by the other objects in adDAX3connTable. All connections are two-way connections, therefore any set operation performed will also change the corresponding table entry for which the To channel is the From channel. In short, any connection can be identified by either side of the connection. The From and To designations have no true directional significance but are used to differentiate between the two sides of the circuit for assigning circuit parameters. To channels and circuit parameters can be assigned but will not take affect until this object is set to 'connected'. |
| INT adDAXFromChannel | 1.3.6.1.4.1.664.2.9.4.1.2 | INTEGER | read-only | This object is the identifier of one of the 24 channels in the DS1 port identified by adDAXFromPort. For 'a1' or 'b1' this object identifies a time slot in the DS1 stream. For 'a0' this object identifies a physical channel slot in the channel bank. |
| INT adDAXFromPort | 1.3.6.1.4.1.664.2.9.4.1.1 | INTEGER | read-only | This object is the identifier of one of the three ports. The ACTDAX serves a a cross-point matrix switch between 72 total DS0 channels distributed in three ports of 24 channels each, and can be configured to cross-connect any of the 72 DS0 channels to any other DS0 channel. The three ports are the DS1 Line A port (a1), the DS1 Line B port (b1), and the channel bank (a0). This object in combination with adDAXFromChannel defines one of the 72 DS0 channels which can be connected. |
| INT adDAXFromTC | 1.3.6.1.4.1.664.2.9.4.1.11 | INTEGER | read-write | The trunk conditioning bits that will be inserted in the From channel in place of received signaling bits during an alarm state on the To channel port. The first two bits will be inserted for the A-bit and B-bit, respectively, during the first 2.5 seconds of the alarm. The second two bits will be inserted for the A-bit and B-bit, respectively, after the first 2.5 seconds of the alarm until the alarm clears. For example, if '0110' is chosen, then during the first 2.5 seconds of the alarm the A-bit will be '0' and the B-bit will be '1'. After the first 2.5 seconds the A-bit will be '1' and the B-bit will be '0'. |
| STR adDAXlastSetResponse | 1.3.6.1.4.1.664.2.9.4.1.15 | DisplayString | read-only | The response to the last set operation performed on an object in this table. The repsonse indicates either SUCCESS or an explanation of failure. |
| INT adDAXPort | 1.3.6.1.4.1.664.2.9.5.1.1 | INTEGER | read-only | This object is the identifier of one of the three ports. The ACTDAX serves a a cross-point matrix switch between 72 total DS0 channels distributed in three ports of 24 channels each, and can be configured to cross-connect any of the 72 DS0 channels to any other DS0 channel. The three ports are the DS1 Line A port (a1), the DS1 Line B port (b1), and the channel bank (a0). |
| INT adDAXSgnlState | 1.3.6.1.4.1.664.2.9.4.1.8 | INTEGER | read-write | The signaling state of the circuit. 'transparent' indicates that no signal bit robbing is performed. 'state2' indicates that the A-bit is robbed and inserted in both the A-bit and B-bit positions in the outgoing data stream. 'state4' indicates that both the A-bit and B-bit are robbed and inserted in the outgoing data stream. 'state16' indicates that the A-bit, B-bit, C-bit, and D-bit are robbed and inserted in the outgoing data stream. The 16-state signaling can only be set for connections between the DS1 lines and then only if the DS1 lines are configured for ESF framing. |
| INT adDAXTermination | 1.3.6.1.4.1.664.2.9.4.1.7 | INTEGER | read-write | The termination status of the circuit. Terminating the circuit in one direction is equivalent to not connecting the circuit in that direction. The Unassigned Channel Code will be transmitted in that direction of the circuit instead of circuit data. In addition, if the Trunk Conditioning signaling bit states are defined, then the post 2.5 second trunk conditioning signaling bits will be inserted in that direction. |
| INT adDAXToChannel | 1.3.6.1.4.1.664.2.9.4.1.5 | INTEGER | read-write | The channel in adDAXToPort that is connected to the channel indicated by adDAXFromPort and adDAXFromChannel. |
| INT adDAXToPort | 1.3.6.1.4.1.664.2.9.4.1.4 | INTEGER | read-write | The port of the DS0 channel connected to the channel indicated by adDAXFromPort and adDAXFromChannel. The three possible ports are the DS1 Line A port (a1), the DS1 Line B port (b1), and the channel bank (a0). |
| INT adDAXToTC | 1.3.6.1.4.1.664.2.9.4.1.12 | INTEGER | read-write | The trunk conditioning bits that will be inserted in the To channel in place of received signaling bits during an alarm state on the From channel port. The first two bits will be inserted for the A-bit and B-bit, respectively, during the first 2.5 seconds of the alarm. The second two bits will be inserted for the A-bit and B-bit, respectively, after the first 2.5 seconds of the alarm until the alarm clears. For example, if '0110' is chosen, then during the first 2.5 seconds of the alarm the A-bit will be '0' and the B-bit will be '1'. After the first 2.5 seconds the A-bit will be '1' and the B-bit will be '0'. |
| STR adDAXTroubleCode | 1.3.6.1.4.1.664.2.9.4.1.10 | DisplayString | read-write | The Trouble Insertion Code that will be inserted toward a DS0 channel instead of outgoing data when the source channels's port is in an alarm state. The TroubleCode will be the same for both the From and To channels. If adDAXTroubleInsert is set to 'none', then the Trouble Code will show 'N/A'. The Trouble Code should be entered as a two digit hex value, i.e. '9A' for a hex value of 9Ah. |
| INT adDAXTroubleInsert | 1.3.6.1.4.1.664.2.9.4.1.9 | INTEGER | read-write | If the source channel's port is in an alarm state, the the Trouble Insertion Code will be inserted toward the DS0 channel in place of the outgoing data. The available options include two common trouble codes, TRB (7f hex) and MOS (9a hex). The Trouble Insertion Code can be set to None to have no Trouble Code inserted and to allow the outgoing data to pass through in alarm conditions. The Trouble Code may also be set to a custom hex value with adACTDAXTroubleCode when this object is set to 'userDefined'. |
| STR adDAXUAC | 1.3.6.1.4.1.664.2.9.4.1.13 | DisplayString | read-write | The Unassigned Channel Code (UAC) is transmitted towards the From channel when the channel is not not assigned to a connection, or the channel is terminated in a connection. The factory default is Command Mode Idle (FEh). The Unassigned Channel Code should be entered as a two digit hex value, i.e. 'FE' for a hex value of FEh. |
| INT adDAXZeroCodeSuppress | 1.3.6.1.4.1.664.2.9.4.1.14 | INTEGER | read-write | This object indicates if Zero Code Suppression is enabled or disabled for the from channel. If Zero Code Suppression is enabled, zero bytes transmitted from the DS1 interface for this channel will be replaced with the code '00000010'. Zero Code Suppression does not apply to DS0 channels in the 'a0' port. |
| GAU adDS1DailyIntervalBESs | 1.3.6.1.4.1.664.2.9.10.1.11 | Gauge | read-only | The number of Bursty Errored Seconds encountered by a DS1 interface in one of the previous daily intervals. |
| GAU adDS1DailyIntervalCSSs | 1.3.6.1.4.1.664.2.9.10.1.8 | Gauge | read-only | The number of Controlled Slip Seconds encountered by a DS1 interface in one of the previous daily intervals. |
| GAU adDS1DailyIntervalDMs | 1.3.6.1.4.1.664.2.9.10.1.12 | Gauge | read-only | The number of Degraded Minutes encountered by a DS1 interface in one of the previous daily intervals. |
| adDS1DailyIntervalEntry | 1.3.6.1.4.1.664.2.9.10.1 | not-accessible | An entry in the DS1 Daily Interval Table. | |
| GAU adDS1DailyIntervalESs | 1.3.6.1.4.1.664.2.9.10.1.4 | Gauge | read-only | The number of Errored Seconds encountered by a DS1 interface in one of the prevoius daily intervals. |
| INT adDS1DailyIntervalIndex | 1.3.6.1.4.1.664.2.9.10.1.1 | INTEGER | read-only | The index value which uniquely identifies the DS1 interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value as a dsx1LineIndex object instance. |
| GAU adDS1DailyIntervalLCVs | 1.3.6.1.4.1.664.2.9.10.1.13 | Gauge | read-only | The number of Line Code Violations encountered by a DS1 interface in one of the previous daily intervals. |
| GAU adDS1DailyIntervalLESs | 1.3.6.1.4.1.664.2.9.10.1.10 | Gauge | read-only | The number of Line Errored Seconds encountered by a DS1 interface in one of the previous daily intervals. |
| INT adDS1DailyIntervalNumber | 1.3.6.1.4.1.664.2.9.10.1.2 | INTEGER | read-only | A number between 1 and 6, where 1 is the most recently completed 15 minute interval and 6 is the least recently completed daily interval (assuming that all 6 intervals are valid). |
| GAU adDS1DailyIntervalPCVs | 1.3.6.1.4.1.664.2.9.10.1.9 | Gauge | read-only | The number of Path Coding Violations encountered by a DS1 interface in one of the previous daily intervals. |
| GAU adDS1DailyIntervalSEFSs | 1.3.6.1.4.1.664.2.9.10.1.6 | Gauge | read-only | The number of Severely Errored Framing Seconds encountered by a DS1 interface in one of the previous daily intervals. |
| GAU adDS1DailyIntervalSESs | 1.3.6.1.4.1.664.2.9.10.1.5 | Gauge | read-only | The number of Severely Errored Seconds encountered by a DS1 interface in one of the previous daily intervals. |
| adDS1DailyIntervalTable | 1.3.6.1.4.1.664.2.9.10 | not-accessible | The DS1 Daily Interval Table. | |
| GAU adDS1DailyIntervalUASs | 1.3.6.1.4.1.664.2.9.10.1.7 | Gauge | read-only | The number of Unavailable Seconds encountered by a DS1 interface in one of the previous daily intervals. |
| INT adDS1DailyIntervalValid | 1.3.6.1.4.1.664.2.9.10.1.3 | INTEGER | read-only | Indicates if this daily interval contains valid data. |
| GAU adDS1FarEndDailyIntervalBESs | 1.3.6.1.4.1.664.2.9.11.1.11 | Gauge | read-only | The number of Far End Bursty Errored Seconds encountered by a DS1 interface in one of the previous daily intervals. |
| GAU adDS1FarEndDailyIntervalCSSs | 1.3.6.1.4.1.664.2.9.11.1.8 | Gauge | read-only | The number of Far End Controlled Slip Seconds encountered by a DS1 interface in one of the previous daily intervals. |
| GAU adDS1FarEndDailyIntervalDMs | 1.3.6.1.4.1.664.2.9.11.1.12 | Gauge | read-only | The number of Far End Degraded Minutes encountered by a DS1 interface in one of the previous daily intervals. |
| adDS1FarEndDailyIntervalEntry | 1.3.6.1.4.1.664.2.9.11.1 | not-accessible | An entry in the DS1 Daily Interval Table. | |
| GAU adDS1FarEndDailyIntervalESs | 1.3.6.1.4.1.664.2.9.11.1.4 | Gauge | read-only | The number of Far End Errored Seconds encountered by a DS1 interface in one of the prevoius daily intervals. |
| INT adDS1FarEndDailyIntervalIndex | 1.3.6.1.4.1.664.2.9.11.1.1 | INTEGER | read-only | The index value which uniquely identifies the DS1 interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value as a dsx1LineIndex object instance. |
| GAU adDS1FarEndDailyIntervalLCVs | 1.3.6.1.4.1.664.2.9.11.1.13 | Gauge | read-only | The number of Far End Line Code Violations encountered by a DS1 interface in one of the previous daily intervals. |
| GAU adDS1FarEndDailyIntervalLESs | 1.3.6.1.4.1.664.2.9.11.1.10 | Gauge | read-only | The number of Far End Line Errored Seconds encountered by a DS1 interface in one of the previous daily intervals. |
| INT adDS1FarEndDailyIntervalNumber | 1.3.6.1.4.1.664.2.9.11.1.2 | INTEGER | read-only | A number between 1 and 6, where 1 is the most recently completed 15 minute interval and 6 is the least recently completed daily interval (assuming that all 6 intervals are valid). |
| GAU adDS1FarEndDailyIntervalPCVs | 1.3.6.1.4.1.664.2.9.11.1.9 | Gauge | read-only | The number of Far End Path Coding Violations encountered by a DS1 interface in one of the previous daily intervals. |
| GAU adDS1FarEndDailyIntervalSEFSs | 1.3.6.1.4.1.664.2.9.11.1.6 | Gauge | read-only | The number of Far End Severely Errored Framing Seconds encountered by a DS1 interface in one of the previous daily intervals. |
| GAU adDS1FarEndDailyIntervalSESs | 1.3.6.1.4.1.664.2.9.11.1.5 | Gauge | read-only | The number of Far End Severely Errored Seconds encountered by a DS1 interface in one of the previous daily intervals. |
| adDS1FarEndDailyIntervalTable | 1.3.6.1.4.1.664.2.9.11 | not-accessible | The DS1 Daily Interval Table. | |
| GAU adDS1FarEndDailyIntervalUASs | 1.3.6.1.4.1.664.2.9.11.1.7 | Gauge | read-only | The number of Far End Unavailable Seconds encountered by a DS1 interface in one of the previous daily intervals. |
| INT adDS1FarEndDailyIntervalValid | 1.3.6.1.4.1.664.2.9.11.1.3 | INTEGER | read-only | Indicates if this far end daily interval contains valid data. |
| adMgmt | 1.3.6.1.4.1.664.2 | |||
| adProducts | 1.3.6.1.4.1.664.1 | |||
| adtran | 1.3.6.1.4.1.664 |
RFC description
Manages configuration and monitoring of the ACTDAX T1 LIU controller for the ACT1241 Channel Bank.
Start monitoring ADTRAN ACTDAX DSL access equipment (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.