CPQWCRM-MIB

All MIBs › CPQWCRM-MIB

Category: Device Management, Hardware and Environment, Vendor: HP/HPE

Description: Manages HP ProLiant Wide-Connect Resource Manager for cluster resource monitoring and failover management.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is CPQWCRM-MIB?

CPQWCRM-MIB is a legacy Compaq (later HP, enterprise OID 232, built on CPQHOST-MIB) proprietary MIB for the Compaq Wired for Management Console/Rack Manager, reporting environmental-controller status. Its objects cover MIB revision/condition, environmental-controller device status, connected-units count, a reference URL, and internal-device detail — type, free-text description, serial number, status, sensor count, and a sensor table (index, type, text, status, value, high/low/warn thresholds) with a parallel output table. As a hardware-status MIB it lets an administrator confirm a rack's environmental sensor readings against configured thresholds. It is deployed on legacy Compaq (HP) rack/console environmental-management hardware. Engineers can download the CPQWCRM-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in CPQWCRM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Legacy Compaq (HP) rack/console environmental-management hardware

Monitoring Examples

An administrator checks internalSensorValue against internalSensorSetWarn to catch a rack environmental sensor approaching its warning threshold on Compaq Wired for Management hardware.

What Can Be Monitored

environmental sensor readings vs. configured thresholds

Imported Objects

From CPQHOST-MIB

compaq

OBJECT-IDENTITY

From RFC-1212

OBJECT-TYPE

From RFC-1215

TRAP-TYPE

From RFC1213-MIB

DisplayString
sysContact
sysDescr
sysLocation
sysName

OIDs

OID symbolic	OID numeric	Type	Access	Description
NTF alarmInternal	1.3.6.1.4.1.232.167.0.5			Internal Unit Alarm
NTF alarmSensorInternal	1.3.6.1.4.1.232.167.0.1			Internal Sensor Alarm
NTF alarmSensorWaterCoolUnit	1.3.6.1.4.1.232.167.0.2			Water Cool Unit Sensor Alarm
NTF alarmWaterCoolUnit	1.3.6.1.4.1.232.167.0.6			Water Cool Unit System Alarm
cpqWcrm	1.3.6.1.4.1.232.167
cpqWcrmControl	1.3.6.1.4.1.232.167.5
cpqWcrmInternalMsgEntry	1.3.6.1.4.1.232.167.2.3.7.2.1		not-accessible	Entries of message table
cpqWcrmInternalMsgTable	1.3.6.1.4.1.232.167.2.3.7.2		not-accessible	Headline of message table
INT cpqWcrmInternalNumberOfMsgs	1.3.6.1.4.1.232.167.2.3.7.1	INTEGER	read-only	Number of messages that can be created with internal sensor
INT cpqWcrmInternalNumberOfOutputs	1.3.6.1.4.1.232.167.2.3.6.1	INTEGER	read-only	Number of outputs available on internal sensor
INT cpqWcrmInternalNumberOfSensors	1.3.6.1.4.1.232.167.2.3.5.1	INTEGER	read-only	Number of sensors connected to sensor unit 1
cpqWcrmInternalOutputEntry	1.3.6.1.4.1.232.167.2.3.6.2.1		not-accessible	Entries of output table
cpqWcrmInternalOutputTable	1.3.6.1.4.1.232.167.2.3.6.2		not-accessible	Headline of output table
cpqWcrmInternalSensorEntry	1.3.6.1.4.1.232.167.2.3.5.2.1		not-accessible	Entries of sensor table
cpqWcrmInternalSensorTable	1.3.6.1.4.1.232.167.2.3.5.2		not-accessible	Headline of sensor table
INT cpqWcrmInternalSerial	1.3.6.1.4.1.232.167.2.3.3	INTEGER	read-only	Serialnumber of sensor unit connected to port 1
INT cpqWcrmInternalStatus	1.3.6.1.4.1.232.167.2.3.4	INTEGER	read-only	General Status sensor unit connected to port 1 (1) OK (2) error, e. g. value overflow (3) configuration of sensor unit has changed, confirmation required (4) reset from sensor unit to confirm configuration changes (5) timeout of sensor unit, confirmation required to unload this unit (6) sensor unit detected, needs to be confirmed (7) unit is not available (8) supply voltage is too low
STR cpqWcrmInternalText	1.3.6.1.4.1.232.167.2.3.2	DisplayString	read-write	Descriptional text for sensor unit connected to port 1
INT cpqWcrmInternalTypeOfDevice	1.3.6.1.4.1.232.167.2.3.1	INTEGER	read-only	Type of sensor unit connected to port 1
INT cpqWcrmLogicRelay	1.3.6.1.4.1.232.167.3.1.4	INTEGER	read-write	Logic of alarm relay: (1) Relay will pick up in case of an alarm (2) Relay will release in case of an alarm (3) Relay off (general)
INT cpqWcrmMibCondition	1.3.6.1.4.1.232.167.1.3	INTEGER	read-only	The overall condition (status) of the system represented by this MIB. (2) OK (3) a minor problem, warning condition (yellow LED on Environmental Controller) (4) a major problem (red LED on Environmental Controller) (5) configuration of sensor units changed or unit detected (red/yellow/green LED on Environmental Controller)
INT cpqWcrmMibMajRev	1.3.6.1.4.1.232.167.1.1	INTEGER	read-only	The Major Revision level. A change in the major revision level represents a major change in the architecture of the MIB. A change in the major revision level may indicate a significant change in the information, correct interpretation of data may require a MIB document with the same major revision level.
INT cpqWcrmMibMinRev	1.3.6.1.4.1.232.167.1.2	INTEGER	read-only	The Minor Revision level. A change in the minor revision level may represent some minor additional support, no changes to any pre-existing information has occurred.
cpqWcrmMibRev	1.3.6.1.4.1.232.167.1
INT cpqWcrmResetRelay	1.3.6.1.4.1.232.167.3.1.3	INTEGER	read-write	Enable or disable acknowledging currently active alarm relay (with 'C' on Environmental Controller).
INT cpqWcrmResetUnit	1.3.6.1.4.1.232.167.5.1	INTEGER	read-write	Command to reset (acknowledge) alarms of Environmental Controller unit. Setting to 'reset' (2) will have same result as pressing 'C' on Units. Variable is automatically set back to 'noReset' (1).
INT cpqWcrmSetBeeper	1.3.6.1.4.1.232.167.3.1.2	INTEGER	read-write	Audible alarm in Environmental Controller unit: (2): beeper is on (1): beeper is off (general)
INT cpqWcrmSetFlowUnit	1.3.6.1.4.1.232.167.3.1.9	INTEGER	read-write	Unit of Water Flow, Liter/min or Gallon/min
INT cpqWcrmSetTempUnit	1.3.6.1.4.1.232.167.3.1.1	INTEGER	read-write	Unit of all temperature values and setpoints, Celsius or Fahrenheit
cpqWcrmSetup	1.3.6.1.4.1.232.167.3
STR cpqWcrmSetupDate	1.3.6.1.4.1.232.167.3.1.6	DisplayString	read-write	actual Date in format DD.MM.YYYY
cpqWcrmSetupGeneral	1.3.6.1.4.1.232.167.3.1
STR cpqWcrmSetupTime	1.3.6.1.4.1.232.167.3.1.7	DisplayString	read-write	actual Time in format HH:MM:SS, HH (0-23), MM (0-59), SS (0-59)
cpqWcrmStatus	1.3.6.1.4.1.232.167.2
INT cpqWcrmStatusDeviceEnvironmentalController	1.3.6.1.4.1.232.167.2.1	INTEGER	read-only	General Status of Environmental Controller unit itself (1) failed (2) OK
cpqWcrmStatusInternalMsg	1.3.6.1.4.1.232.167.2.3.7
cpqWcrmStatusInternalOutputs	1.3.6.1.4.1.232.167.2.3.6
cpqWcrmStatusInternalSensors	1.3.6.1.4.1.232.167.2.3.5
cpqWcrmStatusSensorInternal	1.3.6.1.4.1.232.167.2.3
cpqWcrmStatusSensorWaterCoolUnit	1.3.6.1.4.1.232.167.2.4
cpqWcrmStatusWaterCoolUnitMsg	1.3.6.1.4.1.232.167.2.4.7
cpqWcrmStatusWaterCoolUnitOutputs	1.3.6.1.4.1.232.167.2.4.6
cpqWcrmStatusWaterCoolUnitSensors	1.3.6.1.4.1.232.167.2.4.5
INT cpqWcrmTimeControl	1.3.6.1.4.1.232.167.3.1.8.2.1.6	INTEGER	read-write	Control via RTC
STR cpqWcrmTimeOff	1.3.6.1.4.1.232.167.3.1.8.2.1.5	DisplayString	read-write	Time to switch off current function, Format: HH:MM
STR cpqWcrmTimeOn	1.3.6.1.4.1.232.167.3.1.8.2.1.4	DisplayString	read-write	Time to switch on current function, Format: HH:MM
INT cpqWcrmTimerDayOfWeek	1.3.6.1.4.1.232.167.3.1.8.2.1.3	INTEGER	read-write	Selection of day of week for timer to switch
cpqWcrmTimerEntry	1.3.6.1.4.1.232.167.3.1.8.2.1		not-accessible	Entries of timer-table
INT cpqWcrmTimerFunction	1.3.6.1.4.1.232.167.3.1.8.2.1.7	INTEGER	read-write	Function which is controlled via timer 1-4: sending Traps to this Trap receiver will be disabled 5 - 8: scheduled alarm off
INT cpqWcrmTimerIndex	1.3.6.1.4.1.232.167.3.1.8.2.1.1	INTEGER	read-only	Index for the list of timer entries. Its value ranges between 1 and the value of cpqWcrmTimerNumber.
INT cpqWcrmTimerNumber	1.3.6.1.4.1.232.167.3.1.8.1	INTEGER	read-only	Number of value-table entries=number of outlets available on this unit
INT cpqWcrmTimerStatus	1.3.6.1.4.1.232.167.3.1.8.2.1.2	INTEGER	read-only	Actual status of the timer
cpqWcrmTimerTable	1.3.6.1.4.1.232.167.3.1.8.2		not-accessible	Headline of status-table
cpqWcrmTimerTable1	1.3.6.1.4.1.232.167.3.1.8
cpqWcrmTrapControl	1.3.6.1.4.1.232.167.4
cpqWcrmTraps	1.3.6.1.4.1.232.167.4.7
cpqWcrmTrapTableEntry	1.3.6.1.4.1.232.167.4.7.2.1		not-accessible	Entries of trapTable
INT cpqWcrmTraptableNumber	1.3.6.1.4.1.232.167.4.7.1	INTEGER	read-only	Number of trapTable entries. The number of trap-receiver
cpqWcrmTrapTableTable	1.3.6.1.4.1.232.167.4.7.2		not-accessible	A list of trap-receiver entries
INT cpqWcrmUnitsConnected	1.3.6.1.4.1.232.167.2.2	INTEGER	read-only	Number of sensor units connected to the Environmental Controller, Port 1 to 2
STR cpqWcrmURL	1.3.6.1.4.1.232.167.2.7	DisplayString	read-only	URL of the management interface in the format http[s]://ipaddr[:port#][/page]
cpqWcrmWaterCoolUnitMsgEntry	1.3.6.1.4.1.232.167.2.4.7.2.1		not-accessible	Entries of message table
cpqWcrmWaterCoolUnitMsgTable	1.3.6.1.4.1.232.167.2.4.7.2		not-accessible	Headline of message table
INT cpqWcrmWaterCoolUnitNumberOfMsgs	1.3.6.1.4.1.232.167.2.4.7.1	INTEGER	read-only	Number of alarms that can be created with water cool unit
INT cpqWcrmWaterCoolUnitNumberOfOutputs	1.3.6.1.4.1.232.167.2.4.6.1	INTEGER	read-only	Number of outputs available on sensor water cool unit
INT cpqWcrmWaterCoolUnitNumberOfSensors	1.3.6.1.4.1.232.167.2.4.5.1	INTEGER	read-only	Number of sensors connected to water cool unit
cpqWcrmWaterCoolUnitOutputEntry	1.3.6.1.4.1.232.167.2.4.6.2.1		not-accessible	Entries of output table
cpqWcrmWaterCoolUnitOutputTable	1.3.6.1.4.1.232.167.2.4.6.2		not-accessible	Headline of output table
cpqWcrmWaterCoolUnitSensorEntry	1.3.6.1.4.1.232.167.2.4.5.2.1		not-accessible	Entries of sensor table
cpqWcrmWaterCoolUnitSensorTable	1.3.6.1.4.1.232.167.2.4.5.2		not-accessible	Headline of sensor table
INT cpqWcrmWaterCoolUnitSerial	1.3.6.1.4.1.232.167.2.4.3	INTEGER	read-only	Serialnumber of sensor unit connected to port 2
INT cpqWcrmWaterCoolUnitStatus	1.3.6.1.4.1.232.167.2.4.4	INTEGER	read-only	General Status sensor unit connected to port 2 (1) OK (2) error (3) configuration of sensor unit has changed, confirmation required (4) reset from sensor unit to confirm configuration changes (5) timeout of sensor unit, confirmation required (6) sensor unit detected, needs to be confirmed (8) supply voltage is too low
STR cpqWcrmWaterCoolUnitText	1.3.6.1.4.1.232.167.2.4.2	DisplayString	read-write	Descriptional text for sensor unit connected to port 2
INT cpqWcrmWaterCoolUnitTypeOfDevice	1.3.6.1.4.1.232.167.2.4.1	INTEGER	read-only	Type of sensor unit connected to port 2
INT cpqWcrmWebAccess	1.3.6.1.4.1.232.167.3.1.5	INTEGER	read-write	Web access via HTTP: (1) view only (2) full Access, read and set (3) Web disabled (general)
INT internalMsgBeeper	1.3.6.1.4.1.232.167.2.3.7.2.1.5	INTEGER	read-write	Setup of Alarm beeper for this alarm 1: no audible alarm 2: audible alarm
INT internalMsgIndex	1.3.6.1.4.1.232.167.2.3.7.2.1.1	INTEGER	read-only	Index for the list of message entries. Its value ranges between 1 and the value of cpqWcrmInternalNumberOfMsgs.
INT internalMsgRelay	1.3.6.1.4.1.232.167.2.3.7.2.1.4	INTEGER	read-write	Setup of Alarm relay for this message/alarm 1: no switching of alarm relay 2: switching of alarm relay
INT internalMsgReset	1.3.6.1.4.1.232.167.2.3.7.2.1.10	INTEGER	read-write	Reset of this alarm 1: auto 2: manual, alarm needs confirmation, e. g. with 'C' key
INT internalMsgStatus	1.3.6.1.4.1.232.167.2.3.7.2.1.3	INTEGER	read-only	Actual message status 1: not available 2: configuration has changed (sensor new, changed, lost) 3: error 4: OK 5: alarm, e.g. smoke, vibration... 6: warning of analog value, value reached warning threshold 7: analog value too low, value reached low threshold 8: analog value too high, value reached high threshold 9: output is set to ON 10: output is set to OFF
STR internalMsgText	1.3.6.1.4.1.232.167.2.3.7.2.1.2	DisplayString	read-write	Descriptional text for each message (entry in the table)
INT internalMsgTrap1	1.3.6.1.4.1.232.167.2.3.7.2.1.6	INTEGER	read-write	Trap receiver 1 activated
INT internalMsgTrap2	1.3.6.1.4.1.232.167.2.3.7.2.1.7	INTEGER	read-write	Trap receiver 2 activated
INT internalMsgTrap3	1.3.6.1.4.1.232.167.2.3.7.2.1.8	INTEGER	read-write	Trap receiver 3 activated
INT internalMsgTrap4	1.3.6.1.4.1.232.167.2.3.7.2.1.9	INTEGER	read-write	Trap receiver 4 and Event Logging activated
INT internalOutputConfig	1.3.6.1.4.1.232.167.2.3.6.2.1.7	INTEGER	read-write	Configuration for output 1: disable remote control (e.g. keypad) 2: enable remote control
INT internalOutputDelay	1.3.6.1.4.1.232.167.2.3.6.2.1.8	INTEGER	read-write	Unsigned Value for delay, after this time the output will fall into the previous state
INT internalOutputIndex	1.3.6.1.4.1.232.167.2.3.6.2.1.1	INTEGER	read-only	Index for the list of output entries. Its value ranges between 1 and the value of cpqWcrmInternalNumberOfOutputs.
INT internalOutputSet	1.3.6.1.4.1.232.167.2.3.6.2.1.6	INTEGER	read-write	Command for output
INT internalOutputStatus	1.3.6.1.4.1.232.167.2.3.6.2.1.4	INTEGER	read-write	Actual status of the output
STR internalOutputText	1.3.6.1.4.1.232.167.2.3.6.2.1.3	DisplayString	read-write	Descriptional text for each output (entry in the table)
INT internalOutputTimeoutAction	1.3.6.1.4.1.232.167.2.3.6.2.1.9	INTEGER	read-write	State for output if timeout (RS422) occurs
INT internalOutputType	1.3.6.1.4.1.232.167.2.3.6.2.1.2	INTEGER	read-only	Type of output which is connected to internal sensor to output[internalOutputIndex] 1: no output connected 2: output failure 3: value overflow 4: output type 6, universal relay output 5: output type 8, power output
INT internalOutputValue	1.3.6.1.4.1.232.167.2.3.6.2.1.5	INTEGER	read-write	Value for output
INT internalSensorIndex	1.3.6.1.4.1.232.167.2.3.5.2.1.1	INTEGER	read-only	Index for the list of value entries. Its value ranges between 1 and the value of cpqWcrmInternalNumberOfSensors.
INT internalSensorSetHigh	1.3.6.1.4.1.232.167.2.3.5.2.1.6	INTEGER	read-write	Value for high setpoint of sensor
INT internalSensorSetLow	1.3.6.1.4.1.232.167.2.3.5.2.1.7	INTEGER	read-write	Value for low setpoint of sensor, also used as alarm delay
INT internalSensorSetWarn	1.3.6.1.4.1.232.167.2.3.5.2.1.8	INTEGER	read-write	Value for warning setpoint of sensor, also used as fan threshold
INT internalSensorStatus	1.3.6.1.4.1.232.167.2.3.5.2.1.4	INTEGER	read-only	Actual status of the sensor
STR internalSensorText	1.3.6.1.4.1.232.167.2.3.5.2.1.3	DisplayString	read-write	Descriptional text for each sensor (entry in the table)
INT internalSensorType	1.3.6.1.4.1.232.167.2.3.5.2.1.2	INTEGER	read-only	Type of sensor which is connected to internal sensor to sensor[internalSensorIndex] 1: no sensor connected 2: sensor failure 3: value overflow 4: sensor type 1, access sensor 5: sensor type 2, vibration sensor 6: sensor type 3, motion sensor 7: sensor type 4, smoke sensor 8: sensor type 5, air flow sensor 9: sensor type 6, reserved 10: sensor type 7, temperature sensor 11: sensor type 8, 4..20mA sensor 12: sensor type 9, humidity sensor 13: user sensor with normally opened contact 14: user sensor with normally closed contact 15: door locked sensor from locking device 16: remote unlock sensor (e.g. external keypad) 17: voltage sensor, indicates status of main voltage (OK, NOK) 18: voltage value 19: fan status, from Environmental Controller-FAS-Unit 20: leakage sensor
INT internalSensorValue	1.3.6.1.4.1.232.167.2.3.5.2.1.5	INTEGER	read-only	Value of sensor
NTF testTrap	1.3.6.1.4.1.232.167.0.10			Test trap sent to a trap receiver to check proper reception of traps
INT trapIndex	1.3.6.1.4.1.232.167.4.7.2.1.1	INTEGER	read-only	Index for the trap-receiver-table. Its value ranges between 1 and the value of traptableNumber
STR trapIPaddress	1.3.6.1.4.1.232.167.4.7.2.1.3	DisplayString	read-write	IP-address of trap-receiver
INT trapStatus	1.3.6.1.4.1.232.167.4.7.2.1.2	INTEGER	read-write	Enable or disable trap receiver
INT waterCoolUnitMsgBeeper	1.3.6.1.4.1.232.167.2.4.7.2.1.5	INTEGER	read-write	Setup of Alarm beeper for this alarm 2: no audible alarm 1: audible alarm
INT waterCoolUnitMsgIndex	1.3.6.1.4.1.232.167.2.4.7.2.1.1	INTEGER	read-only	Index for the list of alarm entries. Its value ranges between 1 and the value of cpqWcrmWaterCoolUnitNumberOfMsgs.
INT waterCoolUnitMsgRelay	1.3.6.1.4.1.232.167.2.4.7.2.1.4	INTEGER	read-write	Setup of Alarm relay for this alarm 2: no switching of alarm relay 1: switching of alarm relay
INT waterCoolUnitMsgReset	1.3.6.1.4.1.232.167.2.4.7.2.1.10	INTEGER	read-write	Reset of this alarm 1: auto 2: manual, alarm needs confirmation, e. g. with 'C' key
INT waterCoolUnitMsgStatus	1.3.6.1.4.1.232.167.2.4.7.2.1.3	INTEGER	read-only	Actual message status 4: OK 5: alarm 6: warning 7: analog value too low, value reached low threshold 8: analog value too high, value reached high threshold
STR waterCoolUnitMsgText	1.3.6.1.4.1.232.167.2.4.7.2.1.2	DisplayString	read-write	Descriptional text for each message (entry in the table)
INT waterCoolUnitMsgTrap1	1.3.6.1.4.1.232.167.2.4.7.2.1.6	INTEGER	read-write	Trap receiver 1 activated
INT waterCoolUnitMsgTrap2	1.3.6.1.4.1.232.167.2.4.7.2.1.7	INTEGER	read-write	Trap receiver 2 activated
INT waterCoolUnitMsgTrap3	1.3.6.1.4.1.232.167.2.4.7.2.1.8	INTEGER	read-write	Trap receiver 3 activated
INT waterCoolUnitMsgTrap4	1.3.6.1.4.1.232.167.2.4.7.2.1.9	INTEGER	read-write	Trap receiver 4 and Event Logging activated
INT waterCoolUnitOutputConfig	1.3.6.1.4.1.232.167.2.4.6.2.1.7	INTEGER	read-write	Configuration for output 1: disable remote control (e.g. keypad) 2: enable remote control
INT waterCoolUnitOutputDelay	1.3.6.1.4.1.232.167.2.4.6.2.1.8	INTEGER	read-write	Unsigned Value for delay, after this time the output will fall into the previous state
INT waterCoolUnitOutputIndex	1.3.6.1.4.1.232.167.2.4.6.2.1.1	INTEGER	read-only	Index for the list of output entries. Its value ranges between 1 and the value of cpqWcrmWaterCoolUnitNumberOfOutputs.
INT waterCoolUnitOutputSet	1.3.6.1.4.1.232.167.2.4.6.2.1.6	INTEGER	read-write	Command for output
INT waterCoolUnitOutputStatus	1.3.6.1.4.1.232.167.2.4.6.2.1.4	INTEGER	read-write	Actual status of the output
STR waterCoolUnitOutputText	1.3.6.1.4.1.232.167.2.4.6.2.1.3	DisplayString	read-write	Descriptional text for each output (entry in the table)
INT waterCoolUnitOutputTimeoutAction	1.3.6.1.4.1.232.167.2.4.6.2.1.9	INTEGER	read-write	State for output if timeout (RS422) occurs
INT waterCoolUnitOutputType	1.3.6.1.4.1.232.167.2.4.6.2.1.2	INTEGER	read-only	Type of output which is connected to water cool unit to output[waterCoolUnitOutputIndex] 1: no output connected 2: output failure 3: value overflow 4: water valve setpoint 5: water valve hysteresis 6: command for manual control 7: Flow Meter Model, 0=SIKA, 1=Chemline 8: minimum fan speed 9: min delta T, used for fan control 10: max delta T, used for fan control 11: specific heat capacity 12: setpoint heatload warning 13: setpoint Water Flow Loss Emergency Door Opening 14: setpoint High Temperature Emergency Door Opening 15: setpoint Condensation Pump Cycles (Warning) 16: setpoint Condensation Pump Running Time (Warning) 17: command for door opening, 0=lock door, 1=unlock door 18: KP parameter for PID controller 19: KI parameter for PID controller 20: KD parameter for PID controller 21: sampling time PID controller
INT waterCoolUnitOutputValue	1.3.6.1.4.1.232.167.2.4.6.2.1.5	INTEGER	read-write	Signed value for output
INT waterCoolUnitSensorIndex	1.3.6.1.4.1.232.167.2.4.5.2.1.1	INTEGER	read-only	Index for the list of value entries. Its value ranges between 1 and the value of cpqWcrmWaterCoolUnitNumberOfSensors.
INT waterCoolUnitSensorSetHigh	1.3.6.1.4.1.232.167.2.4.5.2.1.6	INTEGER	read-write	Value for high setpoint of sensor
INT waterCoolUnitSensorSetLow	1.3.6.1.4.1.232.167.2.4.5.2.1.7	INTEGER	read-write	Value for low setpoint of sensor, also used as alarm delay
INT waterCoolUnitSensorSetWarn	1.3.6.1.4.1.232.167.2.4.5.2.1.8	INTEGER	read-write	Value for warning setpoint of sensor, also used as fan threshold
INT waterCoolUnitSensorStatus	1.3.6.1.4.1.232.167.2.4.5.2.1.4	INTEGER	read-only	Actual status of the sensor
STR waterCoolUnitSensorText	1.3.6.1.4.1.232.167.2.4.5.2.1.3	DisplayString	read-write	Descriptional text for each sensor (entry in the table)
INT waterCoolUnitSensorType	1.3.6.1.4.1.232.167.2.4.5.2.1.2	INTEGER	read-only	Type of sensor which is connected to internal sensor to sensor[internalSensorIndex] 1: no sensor connected 2: sensor failure 3: value overflow 4: average temperature of air inlet to rack, average or max/min from each HEX 5: average temperature of air outlet from rack, average or max/min from each HEX 6: heatflow sensor 7: alarm: Bit 0: Leakage Bit 1: IIC Failure 8: warning: Bit 0..2: Fan Tach 1..3 Bit 3,4: Temp. sensor HEX1 In,Out Bit 5,6: Temp. sensor HEX2 In,Out Bit 7,8: Temp. sensor HEX3 In,Out Bit 9: Air temp. sensor Bit 10..12: IIC failure, HEX1..3 Bit 13: Waterflow low Bit 14,15: Watertemp. In,Out Bit 16: Waterflow sensor fail. Bit 17: Magnetic valve fail. Bit 18: Leakdetector fail. Bit 19: Uneven heat load Bit 20: Condensation Pump Cycles > Max Bit 21: Condensation Pump Running Time > Max 9: rpm speed of Fan1 10: rpm speed of Fan2 11: rpm speed of Fan3 12: fanSpeed setpoint, calculated from average temperatures 13: temperature air inlet to rack, HEX 1 14: temperature air outlet from rack, HEX 1 15: temperature air inlet to rack, HEX 1 16: temperature air outlet from rack, HEX 1 17: temperature air inlet to rack, HEX 1 18: temperature air outlet from rack, HEX 1 19: water temperature In 20: water temperature Out 21: water Flow 22: water valve status: MCS:0: Valve opened, 1: valve closed; MCSS: valve setpoint (%) 23: status: Bit 0..Bit 2: fan module 1..3 available Bit 3: water module available 24: condensation pump number of seconds on counter (last operating time) 25: condensation pump on/off cycle counter 26: rpm speed of Fan4 27: rpm speed of Fan5 28: rpm speed of Fan6 29: status of transfer switch, 1=AC1, 2=AC2, 3=AC1 and AC2 30: water valve actual value (%)
INT waterCoolUnitSensorValue	1.3.6.1.4.1.232.167.2.4.5.2.1.5	INTEGER	read-only	Value of sensor added to traps, msg index also added (waterCoolUnitMsgIndex) If msg index = 1, 5 or 6 This value represents the actual Server Intake Temperature. If msg index = 2: This value represents the bit coded warning condition Bit 0: Top Fan Module Failed Bit 1: Middle Fan Module Failed Bit 2: Bottom Fan Module Failed Bit 3: Top HEX Intake Air Temperature Sensor to Server Failed Bit 4: Top HEX Exhaust Air Temperature Sensor from Server Failed Bit 5: Middle HEX Intake Air Temperature Sensor to Server Failed Bit 6: Middle HEX Exhaust Air Temperature Sensor from Server Failed Bit 7: Bottom HEX Intake Air Temperature Sensor to Server Failed Bit 8: Bottom HEX Exhaust Air Temperature Sensor from Server Failed Bit 9: Air Temperature Sensor Failed Bit 10: Top Fan not installed Bit 11: Middle Fan not installed Bit 12: Bottom Fan not installed Bit 13: Waterflow low Bit 14: Water Unit Temperature Input Out of Range Bit 15: Water Unit Temperature Output Out of Range Bit 16: Waterflow Sensor Value Out of Range Bit 17: Water Valve Failed Bit 18: Leakdetector Failed Bit 19: Heat Load Warning Bit 20: The Condensation Pump has exceeded the max. number of cycles Bit 21: The Condensation Pump has exceeded the max. Running Time If msg index = 3: This value represents the bit coded alarm condition Bit 0: Leakage Detected Bit 1: Comm. Failure IIC

RFC description

Compaq (HP) Web-based Console Remote Management MIB. Manages remote console and management features for Compaq servers.

Start monitoring Legacy Compaq (HP) rack/console environmental-management hardware with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CPQWCRM-MIB

What Is CPQWCRM-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description