All MIBs › CPQHOST-MIB
Category: Hardware and Environment, Vendor: HP/HPE
Description: MIB from Compaq (now HPE) covering host operating system monitoring on ProLiant servers, including system parameter management, client identification, and trap delivery.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is CPQHOST-MIB?
CPQHOST-MIB is a Compaq (now HPE) host operating system management MIB used to monitor and manage host-level parameters on Compaq/HPE ProLiant servers running the Insight Management Agents. It covers host OS-level data such as client/host identification and SNMP trap delivery destination configuration, complementing the hardware-focused Compaq/HPE Insight MIBs that report physical component health. Its role in monitoring is centered on software/OS-level status: confirming the correct host identity is reported and that trap destinations are properly configured so fault notifications from the broader Compaq agent suite actually reach the management station. It is designed to be used alongside the rest of the Compaq/HPE Insight Manager MIB family, on which it depends for full server health visibility, and cpqhost-mib is typically loaded into the MIB compiler right beside those companion modules. It's typically deployed on Compaq/HPE ProLiant servers running Insight Management Agent software in Windows or Linux environments.
IPNetwork Monitor allows you to monitor SNMP objects defined in CPQHOST-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- HPE ProLiant DL380 Gen11 (2023) — current 2U 2P rack server, 4th/5th Gen Intel Xeon Scalable, PCIe Gen5
- HPE ProLiant ML350 Gen11 (2023) — current tower server, up to 64 cores, 8TB DDR5
Monitoring Examples
No sample objects were provided for this module, so a concrete polling example cannot be grounded in specific object names; in practice, administrators would use its host identification and trap-destination configuration objects to verify Insight Agent trap notifications are correctly routed to the management station, while actual hardware status such as temperature, power supply, or disk health would be cross-referenced via the companion Compaq Insight MIBs rather than CPQHOST-MIB itself.
What Can Be Monitored
- host/client identification
- SNMP trap destination configuration
- host agent status
This MIB depends on
Related MIBs
Imported Objects
From RFC-1212
| OBJECT-TYPE |
From RFC-1215
| TRAP-TYPE |
From RFC1155-SMI
| IpAddress | |
| enterprises |
From RFC1213-MIB
| DisplayString | |
| sysName |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| compaq | 1.3.6.1.4.1.232 | |||
| NTF cpqHo2AppErrorTrap | 1.3.6.1.4.1.232.0.11004 | An application has generated an exception. Specific error information is contained in the variable cpqHoSwPerfAppErrorDesc. | ||
| NTF cpqHo2GenericTrap | 1.3.6.1.4.1.232.0.11003 | Generic trap. | ||
| NTF cpqHo2NicStatusFailed | 1.3.6.1.4.1.232.0.11006 | This trap will be sent any time the status of a NIC changes to the Failed condition. | ||
| NTF cpqHo2NicStatusFailed2 | 1.3.6.1.4.1.232.0.11009 | This trap will be sent any time the status of a NIC changes to the Failed condition. | ||
| NTF cpqHo2NicStatusOk | 1.3.6.1.4.1.232.0.11005 | This trap will be sent any time the status of a NIC changes to the OK condition. | ||
| NTF cpqHo2NicStatusOk2 | 1.3.6.1.4.1.232.0.11008 | This trap will be sent any time the status of a NIC changes to the OK condition. | ||
| NTF cpqHo2NicSwitchoverOccurred | 1.3.6.1.4.1.232.0.11007 | This trap will be sent any time the configured redundant NIC becomes the active NIC. | ||
| NTF cpqHo2NicSwitchoverOccurred2 | 1.3.6.1.4.1.232.0.11010 | This trap will be sent any time the configured redundant NIC becomes the active NIC. | ||
| NTF cpqHo2PowerThresholdTrap | 1.3.6.1.4.1.232.0.11018 | Power threshold exceeded. | ||
| NTF cpqHoAppErrorTrap | 1.3.6.1.4.1.232.0.11002 | An application has generated an exception. Specific error information is contained in the variable cpqHoSwPerfAppErrorDesc. | ||
| STR cpqHoBootPagingFileMinimumSize | 1.3.6.1.4.1.232.11.2.13.6 | DisplayString | read-only | Minimum paging file size of the boot volume required to save the memory dump in the event of a system crash. The format is xxxMB or xxxGB, where xxx is the minimum paging file size in that unit shown right after it. |
| NTF cpqHoBootPagingFileOrFreeSpaceTooSmallTrap | 1.3.6.1.4.1.232.0.11019 | This trap is sent when the paging file size of the boot volume or the free space of memory dump target volume is too small to hold a crash dump. | ||
| STR cpqHoBootPagingFileSize | 1.3.6.1.4.1.232.11.2.13.5 | DisplayString | read-only | The paging file size of the boot volume in the format xxxMB or xxxGB, where xxx is the paging file size in that unit shown right after it. NULL value will be returned if this value could not be determined. |
| NTF cpqHoBootPagingFileTooSmallTrap | 1.3.6.1.4.1.232.0.11016 | This trap is sent when the paging file size of the boot volume or the target volume of the memory dump file is too small to hold a crash dump. This trap is not sent if cpqHoCrashDumpMonitoring is disabled. | ||
| STR cpqHoBootPagingFileVolumeFreeSpace | 1.3.6.1.4.1.232.11.2.13.7 | DisplayString | read-only | Free space of the boot volume required to save the memory dump in the event of a system crash. The format is xxxMB or xxxGB, where xxx is the minimum paging file size in that unit shown right after it. |
| STR cpqHoClientCommunity | 1.3.6.1.4.1.232.11.2.12.3.1.5 | DisplayString | read-only | A community name that can be used to query the client with SNMP. This community name should have, but is not required to have, the greatest possible access to client information. |
| STR cpqHoClientDelete | 1.3.6.1.4.1.232.11.2.12.2 | DisplayString | read-write | Setting this variable to the name of a client in the client table will cause that row in the table to be deleted. Any other set will fail. Note that the indices of the table will (most likely) be renumbered following a deletion. |
| cpqHoClientEntry | 1.3.6.1.4.1.232.11.2.12.3.1 | not-accessible | A client description. | |
| OCT cpqHoClientID | 1.3.6.1.4.1.232.11.2.12.3.1.6 | OCTET STRING | read-only | The unique identifier of this client. |
| INT cpqHoClientIndex | 1.3.6.1.4.1.232.11.2.12.3.1.1 | INTEGER | read-only | An index that uniquely specifies this entry. |
| IP cpqHoClientIpAddress | 1.3.6.1.4.1.232.11.2.12.3.1.4 | IpAddress | read-only | The IP address for this client, all octets should be set to 0xff if this machine does not support IP. The order will be in network byte order (ie MSB first.) |
| OCT cpqHoClientIpxAddress | 1.3.6.1.4.1.232.11.2.12.3.1.3 | OCTET STRING | read-only | The IPX address for this client, all octets should be set to 0xff if this machine does not support IPX. The format is NetAddr:NodeNumber and sent in MSB order: 1111111111 01234567:890123456789 |
| OCT cpqHoClientLastModified | 1.3.6.1.4.1.232.11.2.12.1 | OCTET STRING | read-only | The date/time of the last modification to the client table. field octets contents range ===== ====== ======= ===== 1 1-2 year 0..65536 2 3 month 1..12 3 4 day 1..31 4 5 hour 0..23 5 6 minute 0..59 6 7 second 0..60 (use 60 for leap-second) This field will be set to all 0's if there are no entries to the client table. The year field will be set to 0xFFFF if the agent does not support the client table. The year field is set with the most significant octet first. |
| STR cpqHoClientName | 1.3.6.1.4.1.232.11.2.12.3.1.2 | DisplayString | read-only | The Win95 machine name of this client. |
| cpqHoClients | 1.3.6.1.4.1.232.11.2.12 | |||
| cpqHoClientTable | 1.3.6.1.4.1.232.11.2.12.3 | not-accessible | A table of client descriptions. | |
| INT cpqHoCodeServer | 1.3.6.1.4.1.232.11.2.10.4 | INTEGER | read-only | This item indicates how many code server shares are currently configured on the system. If the value of this attribute is 0, this server has not been configured with code server shares. |
| cpqHoComponent | 1.3.6.1.4.1.232.11.2 | |||
| OCT cpqHoConfigChangedDate | 1.3.6.1.4.1.232.11.2.10.2 | OCTET STRING | read-only | The date/time when the agents were last loaded. field octets contents range ===== ====== ======= ===== 1 1-2 year 0..65536 2 3 month 1..12 3 4 day 1..31 4 5 hour 0..23 5 6 minute 0..59 6 7 second 0..60 (use 60 for leap-second) This field will be set to year = 0 if the agent cannot provide the date/time. The year field is set with the most significant octet first. |
| cpqHoCpuUtilEntry | 1.3.6.1.4.1.232.11.2.3.1.1 | not-accessible | A description of a CPU's utilization. | |
| INT cpqHoCpuUtilFiveMin | 1.3.6.1.4.1.232.11.2.3.1.1.3 | INTEGER | read-only | The CPU utilization as a percentage of the theoretical maximum during the last five minutes. A value of -1 indicates that no CPU utilization information is available for this processor. |
| INT cpqHoCpuUtilHour | 1.3.6.1.4.1.232.11.2.3.1.1.5 | INTEGER | read-only | The CPU utilization as a percentage of the theoretical maximum during the last hour. A value of -1 indicates that no CPU utilization information is available for this processor. |
| STR cpqHoCpuUtilHwLocation | 1.3.6.1.4.1.232.11.2.3.1.1.6 | DisplayString | read-only | A text description of the hardware location, on complex multi SBB hardware only, for the CPU. A NULL string indicates that the hardware location could not be determined or is irrelevant. |
| INT cpqHoCpuUtilMin | 1.3.6.1.4.1.232.11.2.3.1.1.2 | INTEGER | read-only | The CPU utilization as a percentage of the theoretical maximum during the last minute. A value of -1 indicates that no CPU utilization information is available for this processor. |
| cpqHoCpuUtilTable | 1.3.6.1.4.1.232.11.2.3.1 | not-accessible | A table of CPU utilization entries. | |
| INT cpqHoCpuUtilThirtyMin | 1.3.6.1.4.1.232.11.2.3.1.1.4 | INTEGER | read-only | The CPU utilization as a percentage of the theoretical maximum during the last thirty minutes. A value of -1 indicates that no CPU utilization information is available for this processor. |
| INT cpqHoCpuUtilUnitIndex | 1.3.6.1.4.1.232.11.2.3.1.1.1 | INTEGER | read-only | This number uniquely specifies a processor unit. A processing unit may be a set of processing chips that are on the same board or for other reasons work together as a unit. The main processor unit (if such a concept is valid for this machine) will always have the lowest (first) index. |
| INT cpqHoCrashDumpCondition | 1.3.6.1.4.1.232.11.2.2.9 | INTEGER | read-only | The condition of the Crash dump configuration. |
| INT cpqHoCrashDumpMonitoring | 1.3.6.1.4.1.232.11.2.2.10 | INTEGER | read-write | Enable/disable crash dump monitoring. If crash dump monitoring is enabled both crash dump TRAP's are generated and crash dump condition is updated. If crash dump monitoring is disabled, no crash dump TRAP is generated and the crash dump condition is set to other |
| NTF cpqHoCrashDumpNotEnabledTrap | 1.3.6.1.4.1.232.0.11015 | This trap is sent to the user to notify him that the Crash Dump is not enabled. This trap is not sent if cpqHoCrashDumpMonitoring is disabled. | ||
| INT cpqHoCrashDumpState | 1.3.6.1.4.1.232.11.2.2.8 | INTEGER | read-only | Crash dump state. Value of 'Unknown (-1)' is returned when crash dump state could not be determined. |
| STR cpqHoCriticalSoftwareUpdateData | 1.3.6.1.4.1.232.11.2.8.2 | DisplayString | read-write | Data for the Critical Software Update trap. |
| NTF cpqHoCriticalSoftwareUpdateTrap | 1.3.6.1.4.1.232.0.11014 | This trap is a send to the user to notify him of a Critical Software Update. | ||
| STR cpqHoDesc | 1.3.6.1.4.1.232.11.2.2.3 | DisplayString | read-only | A further description of the host OS. |
| cpqHoFileSys | 1.3.6.1.4.1.232.11.2.4 | |||
| INT cpqHoFileSysAllocUnitsTotal | 1.3.6.1.4.1.232.11.2.4.1.1.6 | INTEGER | read-only | The total number of files (directory entries) that can be stored on the file system if a limit exists other than total space used. This item will be set to -1 if no such limit exists. |
| INT cpqHoFileSysAllocUnitsUsed | 1.3.6.1.4.1.232.11.2.4.1.1.7 | INTEGER | read-only | The number of files (directory entries) on this file system. This item will be set to -1 if the agent does not determine this information. |
| INT cpqHoFileSysCondition | 1.3.6.1.4.1.232.11.2.4.2 | INTEGER | read-only | The overall condition of File System Threshold. This object represents the overall status of the server's File System Threshold. |
| STR cpqHoFileSysDesc | 1.3.6.1.4.1.232.11.2.4.1.1.2 | DisplayString | read-only | A description of the file system. |
| cpqHoFileSysEntry | 1.3.6.1.4.1.232.11.2.4.1.1 | not-accessible | A file system description. | |
| INT cpqHoFileSysIndex | 1.3.6.1.4.1.232.11.2.4.1.1.1 | INTEGER | read-only | An index that uniquely specifies this entry. |
| INT cpqHoFileSysPercentSpaceUsed | 1.3.6.1.4.1.232.11.2.4.1.1.5 | INTEGER | read-only | The percent of file system space currently in use. This item will be set to -1 if this information is not available. |
| INT cpqHoFileSysSpaceTotal | 1.3.6.1.4.1.232.11.2.4.1.1.3 | INTEGER | read-only | The file system size in megabytes. This item will be set to -1 if the agent is unable to determine this information. |
| INT cpqHoFileSysSpaceUsed | 1.3.6.1.4.1.232.11.2.4.1.1.4 | INTEGER | read-only | The megabytes of file system space currently in use. This item will be set to -1 if the agent is unable to determine this information. |
| INT cpqHoFileSysStatus | 1.3.6.1.4.1.232.11.2.4.1.1.8 | INTEGER | read-only | The Threshold Status. This object represent the status of the Filesystem threshold. |
| cpqHoFileSysTable | 1.3.6.1.4.1.232.11.2.4.1 | not-accessible | A table of file system descriptions. | |
| cpqHoFwVer | 1.3.6.1.4.1.232.11.2.14 | |||
| INT cpqHoFwVerCategory | 1.3.6.1.4.1.232.11.2.14.1.1.2 | INTEGER | read-only | Firmware Version Category. |
| INT cpqHoFwVerDeviceType | 1.3.6.1.4.1.232.11.2.14.1.1.3 | INTEGER | read-only | Firmware Version Device Type. |
| STR cpqHoFwVerDisplayName | 1.3.6.1.4.1.232.11.2.14.1.1.4 | DisplayString | read-only | Firmware Version Device Display Name. This is the display name of the device containing the firmware. |
| cpqHoFwVerEntry | 1.3.6.1.4.1.232.11.2.14.1.1 | not-accessible | A list of firmware items that are on the machine. | |
| INT cpqHoFwVerIndex | 1.3.6.1.4.1.232.11.2.14.1.1.1 | INTEGER | read-only | Firmware Version Index. The firmware version index uniquely identifies an entry in the cpqHoFwVer table. |
| STR cpqHoFwVerKeyString | 1.3.6.1.4.1.232.11.2.14.1.1.8 | DisplayString | read-only | Firmware Version Key String. This field is differentiate devices of the same type. |
| STR cpqHoFwVerLocation | 1.3.6.1.4.1.232.11.2.14.1.1.6 | DisplayString | read-only | Firmware Version Device Location. This is a printable string that specifies the location of the device that contains the firmware. |
| cpqHoFwVerTable | 1.3.6.1.4.1.232.11.2.14.1 | not-accessible | A list of firmware item entries. | |
| INT cpqHoFwVerUpdateMethod | 1.3.6.1.4.1.232.11.2.14.1.1.9 | INTEGER | read-only | Firmware Version update method. |
| STR cpqHoFwVerVersion | 1.3.6.1.4.1.232.11.2.14.1.1.5 | DisplayString | read-only | Firmware Version. This is the version of the device firmware. |
| STR cpqHoFwVerXmlString | 1.3.6.1.4.1.232.11.2.14.1.1.7 | DisplayString | read-only | Firmware Version Xml String. This is an XML string that specifies the location of the device that contains the firmware. This will be NULL string (size 0) if this information could not be provided. |
| cpqHoGeneric | 1.3.6.1.4.1.232.11.2.8 | |||
| STR cpqHoGenericData | 1.3.6.1.4.1.232.11.2.8.1 | DisplayString | read-write | Data for the generic trap. |
| NTF cpqHoGenericTrap | 1.3.6.1.4.1.232.0.11001 | Generic trap. | ||
| OCT cpqHoGUID | 1.3.6.1.4.1.232.11.2.10.3 | OCTET STRING | read-write | The globally unique identifier of this physical server. If the OS cannot determine a unique ID, it will default the variable to contain all 0's. The management station can then perform a SET to this variable to provide the unique ID. When the system is cellular, it will have its partition number appended at the end. |
| OCT cpqHoGUIDCanonical | 1.3.6.1.4.1.232.11.2.10.6 | OCTET STRING | read-write | The globally unique identifier in canonical format of this physical server. If the OS cannot determine a unique ID, it will default the variable to blank. |
| cpqHoHWInfo | 1.3.6.1.4.1.232.11.2.15 | |||
| INT cpqHoHWInfoPlatform | 1.3.6.1.4.1.232.11.2.15.1 | INTEGER | read-only | Hardware platform type. This object represents the platform type of the server's host system represented by this MIB. |
| cpqHoIfPhysMap | 1.3.6.1.4.1.232.11.2.5 | |||
| INT cpqHoIfPhysMapCondition | 1.3.6.1.4.1.232.11.2.5.1.1.9 | INTEGER | read-only | The condition of this interface. |
| INT cpqHoIfPhysMapDma | 1.3.6.1.4.1.232.11.2.5.1.1.5 | INTEGER | read-only | The number of the DMA channel used for this physical hardware interface. The number -1 indicates that this device does not use a DMA channel or this information is unavailable. |
| INT cpqHoIfPhysMapDuplexState | 1.3.6.1.4.1.232.11.2.5.1.1.8 | INTEGER | read-only | This variable describes the configured duplex state of the NIC. |
| cpqHoIfPhysMapEntry | 1.3.6.1.4.1.232.11.2.5.1.1 | not-accessible | A mapping of an interface table entry to physical hardware. | |
| INT cpqHoIfPhysMapIndex | 1.3.6.1.4.1.232.11.2.5.1.1.1 | INTEGER | read-only | An index that uniquely specifies this entry. This value is equal to the index of the entry in the MIB-II interface table to which this entry corresponds. |
| INT cpqHoIfPhysMapIoBaseAddr | 1.3.6.1.4.1.232.11.2.5.1.1.3 | INTEGER | read-only | The base I/O address of the physical hardware that implements this interface. |
| INT cpqHoIfPhysMapIrq | 1.3.6.1.4.1.232.11.2.5.1.1.4 | INTEGER | read-only | The number of the IRQ (interrupt) used for this physical hardware interface. The number zero (0) indicates that this device does not use an IRQ or this information is unavailable. |
| INT cpqHoIfPhysMapMemBaseAddr | 1.3.6.1.4.1.232.11.2.5.1.1.6 | INTEGER | read-only | The base memory address used by this physical hardware interface. The number zero (0) indicates that this device does not use system memory or this information is unavailable. |
| INT cpqHoIfPhysMapOverallCondition | 1.3.6.1.4.1.232.11.2.5.2 | INTEGER | read-only | The overall condition of all interfaces. |
| INT cpqHoIfPhysMapPort | 1.3.6.1.4.1.232.11.2.5.1.1.7 | INTEGER | read-only | The port number of the interface for multi-port NICs. A port number of -1 indicates that the port could not be determined. |
| INT cpqHoIfPhysMapSlot | 1.3.6.1.4.1.232.11.2.5.1.1.2 | INTEGER | read-only | The number of the slot containing the physical hardware that implements this interface. The number zero (0) indicates an embedded interface (on the system board) or an interface whose slot is unknown. Values may be unknown if the physical hardware has not been configured using the EISA Configuration Utility. |
| cpqHoIfPhysMapTable | 1.3.6.1.4.1.232.11.2.5.1 | not-accessible | A table of interface to physical hardware mappings. | |
| cpqHoInfo | 1.3.6.1.4.1.232.11.2.2 | |||
| cpqHoInterface | 1.3.6.1.4.1.232.11.2.1 | |||
| INT cpqHoMaxLogicalCPUSupported | 1.3.6.1.4.1.232.11.2.2.11 | INTEGER | read-only | Maximum number of logical CPUs supported by Operating System. |
| cpqHoMemory | 1.3.6.1.4.1.232.11.2.13 | |||
| INT cpqHoMibCondition | 1.3.6.1.4.1.232.11.1.3 | INTEGER | read-only | The overall condition. This object represents the overall status of the server's host system represented by this MIB. |
| cpqHoMibRev | 1.3.6.1.4.1.232.11.1 | |||
| INT cpqHoMibRevMajor | 1.3.6.1.4.1.232.11.1.1 | INTEGER | read-only | The Major Revision level of the MIB. A change in the major revision level represents a major change in the architecture of the MIB. A change in the major revision level may indicate a significant change in the information supported and/or the meaning of the supported information. Correct interpretation of data may require a MIB document with the same major revision level. |
| INT cpqHoMibRevMinor | 1.3.6.1.4.1.232.11.1.2 | INTEGER | read-only | The Minor Revision level of the MIB. A change in the minor revision level may represent some minor additional support, no changes to any pre-existing information has occurred. |
| OCT cpqHoMibStatusArray | 1.3.6.1.4.1.232.11.2.10.1 | OCTET STRING | read-only | The MIB Status Array is an array of MIB status structures. Each structure is made up of 4 octets. The first octet is the MIB presence. The second octet is MIB condition. The third octet is MIB major revision. The fourth octet is MIB minor revision. These blocks of 4 octets each are index by the mib identifier just after the compaq enterprise (eg in 1.3.6.1.232.11 mib, the index is 11). The 4 octets in the first block (block 0) are reserved for systems management and serve as an aggregate of the other mibs. Array element 0 is the status for all MIBs in the Compaq Enterprise. Array element n, where n > 0, is the status for the nth MIB in the Compaq Enterprise (.1.3.6.1.4.1.232.n). Octet Element Field ======== ======= ========= 0 0 Status of any Compaq MIBs 1 Condition of all Compaq MIBs 2 System Flags (see below) 3 Detailed type (see below) 4 1 Status of Compaq MIB 1 5 Condition of Compaq MIB 1 6 Major Revision of Compaq MIB 1 7 Minor Revision of Compaq MIB 1 8 2 Status of Compaq MIB 2 9 Condition of Compaq MIB 2 10 Major Revision of Compaq MIB 2 11 Minor Revision of Compaq MIB 2 . . . . n*4 n Status of Compaq MIB n (n*4)+1 Condition of Compaq MIB n (n*4)+2 Major Revision of Compaq MIB n (n*4)+3 Minor Revision of Compaq MIB n System Flags (octet 2) Bit Meaning ===== ========= 0 Equals 1 if the device is not a server, see detailed type below Equals 0 if the device is a server 1 This system contains enabled remote console functionality. 2 This system is configured to be an Integration Server. 3 Web Based Management is enabled. 4-7 Reserved (reserved Bits should be zero) Detailed Type (octet 3) Bits 0-4 Detailed Type, only used if bit 0 in octet 2 is 1. Bits 5-7 Reserved for expansion. note, use these last in case we need more then 32 types someday. Type Values for Bits 0-4 (maps to CIM7 types) Unknown = 0 Server = 1 (yes a duplicate of the server flag) Desktop = 2 Workstation = 3 Portable = 4 Router = 5 Cluster = 6 Printer = 7 Switch = 8 (network switch) Repeater = 9 Remote Access Device = 10 Other = 11 Management Processor = 12 (rib, RILOE, iLo) Rack = 13 Enclosure = 14 KVM Switch = 15 (IP enabled keyboard video mouse switch). UPS = 16 Power Distribution Unit = 17 Environmental Monitor = 18 (eg CMC) Power Distribution Rack = 19 (PDR) Storage Device = 20 For all other blocks, they are defined as: Status This is a collection of flags. Each bit has the following meaning when it is on (1): Bit 2-7: RESERVED: Always 0 Bit 1: MIB is from offline data (only applies to global system status) Bit 0: MIB is available NOTE: bit 7 is the most significant bit, bit 0 is the least significant. Condition 0 - Not available 1 - Other 2 - OK 3 - Degraded 4 - Failed Major Revision 0..255, where 0 is not available Minor Revision 0..255, where 0 is not available |
| STR cpqHoName | 1.3.6.1.4.1.232.11.2.2.1 | DisplayString | read-only | The name of the host operating system (OS). |
| cpqHoOsCommon | 1.3.6.1.4.1.232.11.2.1.4 | |||
| OCT cpqHoOsCommonModuleDate | 1.3.6.1.4.1.232.11.2.1.4.2.1.4 | OCTET STRING | read-only | The module date. field octets contents range ===== ====== ======= ===== 1 1-2 year 0..65536 2 3 month 1..12 3 4 day 1..31 4 5 hour 0..23 5 6 minute 0..59 6 7 second 0..60 (use 60 for leap-second) This field will be set to year = 0 if the agent cannot provide the module date. The hour, minute, and second field will be set to zero (0) if they are not relevant. The year field is set with the most significant octet first. |
| cpqHoOsCommonModuleEntry | 1.3.6.1.4.1.232.11.2.1.4.2.1 | not-accessible | A description of a software module that provides an interface to the device this MIB describes. | |
| INT cpqHoOsCommonModuleIndex | 1.3.6.1.4.1.232.11.2.1.4.2.1.1 | INTEGER | read-only | A unique index for this module description. |
| STR cpqHoOsCommonModuleName | 1.3.6.1.4.1.232.11.2.1.4.2.1.2 | DisplayString | read-only | The module name. |
| STR cpqHoOsCommonModulePurpose | 1.3.6.1.4.1.232.11.2.1.4.2.1.5 | DisplayString | read-only | The purpose of the module described in this entry. |
| cpqHoOsCommonModuleTable | 1.3.6.1.4.1.232.11.2.1.4.2 | not-accessible | A table of software modules that provide an interface to the device this MIB describes. | |
| STR cpqHoOsCommonModuleVersion | 1.3.6.1.4.1.232.11.2.1.4.2.1.3 | DisplayString | read-only | The module version in XX.YY format. Where XX is the major version number and YY is the minor version number. This field will be null (size 0) string if the agent cannot provide the module version. |
| INT cpqHoOsCommonPollFreq | 1.3.6.1.4.1.232.11.2.1.4.1 | INTEGER | read-write | The Insight Agent's polling frequency. The frequency, in seconds, at which the Insight Agent requests information from the device driver. A frequency of zero (0) indicates that the Insight Agent retrieves the information upon request of a management station, it does not poll the device driver at a specific interval. If the poll frequency is zero (0) all attempts to write to this object will fail. If the poll frequency is non-zero, setting this value will change the polling frequency of the Insight Agent. Setting the poll frequency to zero (0) will always fail. An agent may choose to fail any request to change the poll frequency to a value that would severely impact system performance. |
| INT cpqHoOsType | 1.3.6.1.4.1.232.11.2.2.4 | INTEGER | read-only | Host Operating system enumeration. |
| INT cpqHoPagingMemoryFree | 1.3.6.1.4.1.232.11.2.13.4 | INTEGER | read-only | Available paging memory (in megabytes). A -1 will be returned if this value could not be determined. |
| INT cpqHoPagingMemorySize | 1.3.6.1.4.1.232.11.2.13.3 | INTEGER | read-only | Total virtual memory available from the OS (in megabytes). A -1 will be returned if this value could not be determined. |
| INT cpqHoPhysicalMemoryFree | 1.3.6.1.4.1.232.11.2.13.2 | INTEGER | read-only | The amount of free physical memory (in megabytes). A -1 will be returned if this value could not be determined. |
| INT cpqHoPhysicalMemorySize | 1.3.6.1.4.1.232.11.2.13.1 | INTEGER | read-only | Total amount of physical memory as seen by the OS (in megabytes). A -1 will be returned if this value could not be determined. |
| NTF cpqHoProcessCountNormal | 1.3.6.1.4.1.232.0.11013 | A monitored process count has returned back to normal. | ||
| NTF cpqHoProcessCountWarning | 1.3.6.1.4.1.232.0.11012 | A monitored process count has violated the thresholds set on cpqHoSWRunningCount | ||
| NTF cpqHoProcessEventTrap | 1.3.6.1.4.1.232.0.11011 | A monitored process has either started or stopped running. | ||
| cpqHostOs | 1.3.6.1.4.1.232.11 | |||
| cpqHoSwPerf | 1.3.6.1.4.1.232.11.2.9 | |||
| STR cpqHoSwPerfAppErrorDesc | 1.3.6.1.4.1.232.11.2.9.1 | DisplayString | read-only | This string holds error information about the last application error that occurred in the system. |
| cpqHoSWRunning | 1.3.6.1.4.1.232.11.2.6 | |||
| INT cpqHoSWRunningConfigStatus | 1.3.6.1.4.1.232.11.2.6.1.1.13 | INTEGER | read-only | The configuration state of the software. The level of initialization the software has performed. |
| INT cpqHoSWRunningCount | 1.3.6.1.4.1.232.11.2.6.1.1.8 | INTEGER | read-only | For each process name, the number of instances of the process running on the system is kept count of, in this variable. |
| INT cpqHoSWRunningCountMax | 1.3.6.1.4.1.232.11.2.6.1.1.10 | INTEGER | read-write | This is the upper threshold on cpqHoSWRunningCount to be set by the user. |
| INT cpqHoSWRunningCountMin | 1.3.6.1.4.1.232.11.2.6.1.1.9 | INTEGER | read-write | This is the lower threshold on cpqHoSWRunningCount to be set by the user. |
| OCT cpqHoSWRunningDate | 1.3.6.1.4.1.232.11.2.6.1.1.5 | OCTET STRING | read-only | The software date. field octets contents range ===== ====== ======= ===== 1 1-2 year 0..65536 2 3 month 1..12 3 4 day 1..31 4 5 hour 0..23 5 6 minute 0..59 6 7 second 0..60 (use 60 for leap-second) This field will be set to year = 0 if the agent cannot provide the software date. The hour, minute, and second field will be set to zero (0) if they are not relevant. |
| STR cpqHoSWRunningDesc | 1.3.6.1.4.1.232.11.2.6.1.1.3 | DisplayString | read-only | A description of the software. |
| cpqHoSWRunningEntry | 1.3.6.1.4.1.232.11.2.6.1.1 | not-accessible | A description of a software program running on the system. | |
| OCT cpqHoSWRunningEventTime | 1.3.6.1.4.1.232.11.2.6.1.1.11 | OCTET STRING | read-only | The system time at which the monitored event, as per cpqHoSWRunningMonitor, last occurred. field octets contents range ===== ====== ======== ===== 1 1-2 year 0..65536 2 3 month 1..12 3 4 day 1..31 4 5 hour 0..23 5 6 minute 0..59 6 7 second 0..60 (use 60 for leap-second) The hour, minute, and second field will be set to zero (0) if they are not relevant. |
| STR cpqHoSWRunningIdentifier | 1.3.6.1.4.1.232.11.2.6.1.1.14 | DisplayString | read-only | The unique identifier of the sofware. This identifier should be unique for all instances of the sofware running in the environment. |
| INT cpqHoSWRunningIndex | 1.3.6.1.4.1.232.11.2.6.1.1.1 | INTEGER | read-only | An index that uniquely specifies this entry. |
| INT cpqHoSWRunningMonitor | 1.3.6.1.4.1.232.11.2.6.1.1.6 | INTEGER | read-only | The user specified monitor option for a process. |
| STR cpqHoSWRunningName | 1.3.6.1.4.1.232.11.2.6.1.1.2 | DisplayString | read-only | The name of the software. |
| INT cpqHoSWRunningRedundancyMode | 1.3.6.1.4.1.232.11.2.6.1.1.15 | INTEGER | read-only | When the software is running in a high availability mode, the failover mode of this instance of the software. |
| INT cpqHoSWRunningState | 1.3.6.1.4.1.232.11.2.6.1.1.7 | INTEGER | read-only | The current state of monitored process. |
| INT cpqHoSWRunningStatus | 1.3.6.1.4.1.232.11.2.6.1.1.12 | INTEGER | read-only | The overall alarm state of the resources managed by the software, or the software itself. |
| NTF cpqHoSWRunningStatusChangeTrap | 1.3.6.1.4.1.232.0.11017 | This trap notifies the user that the running software has changed status, configuration status, or redundancy mode. | ||
| cpqHoSWRunningTable | 1.3.6.1.4.1.232.11.2.6.1 | not-accessible | A table of descriptions of software running on the system. | |
| STR cpqHoSwRunningTrapDesc | 1.3.6.1.4.1.232.11.2.6.2 | DisplayString | read-only | The error message for a process monitor event. |
| STR cpqHoSWRunningVersion | 1.3.6.1.4.1.232.11.2.6.1.1.4 | DisplayString | read-only | The version of the software. This field will be a null (size 0) string if the agent cannot provide the software version. |
| cpqHoSwVer | 1.3.6.1.4.1.232.11.2.7 | |||
| STR cpqHoSwVerAgentsVer | 1.3.6.1.4.1.232.11.2.7.3 | DisplayString | read-only | A string that specifies the version of the Insight Management Agents running on the system. |
| OCT cpqHoSwVerDate | 1.3.6.1.4.1.232.11.2.7.2.1.6 | OCTET STRING | read-only | The date of the software item, if any. field octets contents range ===== ====== ======= ===== 1 1-2 year 0..65535 2 3 month 1..12 3 4 day 1..31 4 5 hour 0..23 5 6 minute 0..59 6 7 second 0..60 (use 60 for leap-second) The year field is set with the most significant octet first. An entry of zero (0) means that there is no date associated with this software item. Zero is the default. |
| STR cpqHoSwVerDescription | 1.3.6.1.4.1.232.11.2.7.2.1.5 | DisplayString | read-write | The description of this software item. |
| cpqHoSwVerEntry | 1.3.6.1.4.1.232.11.2.7.2.1 | not-accessible | A list of software items that are on the machine. | |
| INT cpqHoSwVerIndex | 1.3.6.1.4.1.232.11.2.7.2.1.1 | INTEGER | read-only | An index that uniquely identifies an entry in the cpqHoSwVer table. |
| STR cpqHoSwVerLocation | 1.3.6.1.4.1.232.11.2.7.2.1.7 | DisplayString | read-write | The location of this software item on the server. |
| STR cpqHoSwVerName | 1.3.6.1.4.1.232.11.2.7.2.1.4 | DisplayString | read-write | The name of this software item. |
| INT cpqHoSwVerNextIndex | 1.3.6.1.4.1.232.11.2.7.1 | INTEGER | read-only | The index of the next available entry in the cpqHoSwVer table. If the maximum number of entries to the cpqHoSwVer table has been reached, this index will contain -1. |
| INT cpqHoSwVerStatus | 1.3.6.1.4.1.232.11.2.7.2.1.2 | INTEGER | read-only | Status for the software item. |
| cpqHoSwVerTable | 1.3.6.1.4.1.232.11.2.7.2 | not-accessible | A list of software item entries. | |
| INT cpqHoSwVerType | 1.3.6.1.4.1.232.11.2.7.2.1.3 | INTEGER | read-write | Type of software item. |
| STR cpqHoSwVerVersion | 1.3.6.1.4.1.232.11.2.7.2.1.8 | DisplayString | read-only | An string that specifies the version of this item. |
| STR cpqHoSwVerVersionBinary | 1.3.6.1.4.1.232.11.2.7.2.1.9 | DisplayString | read-only | An string that specifies the version of this item based on the binary version resource. |
| STR cpqHoSystemRole | 1.3.6.1.4.1.232.11.2.2.6 | DisplayString | read-write | The system role. This is a settable free form text field intended to be assigned by a remote console briefly describing the system's function. |
| STR cpqHoSystemRoleDetail | 1.3.6.1.4.1.232.11.2.2.7 | DisplayString | read-write | The system detailed description. This is a settable free form text field intended to be assigned by a remote console describing the system function in detail. |
| cpqHoSystemStatus | 1.3.6.1.4.1.232.11.2.10 | |||
| INT cpqHoTelnet | 1.3.6.1.4.1.232.11.2.2.5 | INTEGER | read-only | Telnet on socket 23 is available. |
| INT cpqHoTrapFlags | 1.3.6.1.4.1.232.11.2.11.1 | INTEGER | read-only | The Trap Flags. This is a collection of flags used during trap delivery. Each bit has the following meaning: Bit 5-31: RESERVED: Always 0. Bit 2-4: Trap Condition 0 = Not used (for backward compatibility) 1 = Condition unknown or N/A 2 = Condition ok 3 = Condition degraded 4 = Condition failed 5-7 = reserved Bit 1: Client IP address type 0 = static entry 1 = DHCP entry Bit 0: Agent Type 0 = Server 1 = Client NOTE: bit 31 is the most significant bit, bit 0 is the least significant. |
| cpqHoTrapInfo | 1.3.6.1.4.1.232.11.2.11 | |||
| cpqHoUtil | 1.3.6.1.4.1.232.11.2.3 | |||
| STR cpqHoVersion | 1.3.6.1.4.1.232.11.2.2.2 | DisplayString | read-only | The version of the host OS. |
| INT cpqHoWebMgmtPort | 1.3.6.1.4.1.232.11.2.10.5 | INTEGER | read-only | This item indicates the port used by the Insight Web Agent. If the port cannot be determined or the Web Management agent is not enabled, this value will be -1. |
| cpqPwrThreshold | 1.3.6.1.4.1.232.11.2.16 | |||
| INT cpqPwrWarnDuration | 1.3.6.1.4.1.232.11.2.16.3 | INTEGER | read-write | Duration that power usage must be exceeded before warning (in minutes). |
| INT cpqPwrWarnThreshold | 1.3.6.1.4.1.232.11.2.16.2 | INTEGER | read-write | The threshold the power usage must exceed (in Watts). |
| STR cpqPwrWarnType | 1.3.6.1.4.1.232.11.2.16.1 | DisplayString | read-write | Type of power reading on which the warning is based. |
| STR cpqSerialNum | 1.3.6.1.4.1.232.11.2.16.4 | DisplayString | read-write | Serial number of the server. |
| STR cpqServerUUID | 1.3.6.1.4.1.232.11.2.16.5 | DisplayString | read-write | Server UUID |
RFC description
Compaq (now HPE) host operating system MIB for monitoring and managing host system parameters, client identification, and trap delivery on Compaq/HPE ProLiant servers.
Start monitoring HP/Compaq ProLiant server (host OS management) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.