CISCO-WAN-CELL-EXT-MIB

All MIBs › CISCO-WAN-CELL-EXT-MIB

Organization: Cisco Systems, Inc.

Last Updated: 2014-03-05

Category: Network Interfaces, Vendor: Cisco Devices

Description: Extends Cisco WAN cellular interface management with additional 3G/4G modem configuration objects.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is CISCO-WAN-CELL-EXT-MIB?

CISCO-WAN-CELL-EXT-MIB is a Cisco enterprise MIB that extends CISCO-WAN-3G-MIB to add management support for Cisco's cellular WAN 4G/LTE modem products used in routers and industrial gateways. It exposes radio-layer performance data such as signal strength and quality indicators (RSRP, RSRQ, SNR, SINR, CQI) along with the modem's current operating band and configurable notification thresholds. Its primary monitoring use is hardware/radio status of the embedded LTE modem, tracking degrading signal conditions before they cause a WAN link outage, rather than general CPU/memory or environmental data. As an extension module it explicitly depends on CISCO-WAN-3G-MIB for its base object definitions and conventions. It is typically deployed on Cisco branch, industrial (IR8xx/IR1101-class), or IoT gateway routers that use LTE as a primary or backup WAN uplink. Engineers can download the CISCO-WAN-CELL-EXT-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in CISCO-WAN-CELL-EXT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Cisco cellular WAN router/gateway with 4G/LTE modem
Cisco IR8xx/IR1101 series industrial routers

Monitoring Examples

cwceLteRadioTable/cwceLteRadioEntry rows expose cwceLteCurrRsrp, cwceLteCurrRsrq, cwceLteCurrSnr, and cwceLteCurrSinr per radio instance, which an admin polls to detect degrading LTE signal quality at a remote site. Threshold objects cwceLteRsrpOnsetNotifThreshold and cwceLteRsrpAbateNotifThreshold pair with cwceLteNotifRsrp to trigger notifications from ciscoWanCellExtMIBNotifs when signal drops below or recovers above a configured RSRP threshold, alerting ops before the link fails.

What Can Be Monitored

LTE signal strength (RSRP)
reference signal quality (RSRQ)
SNR/SINR
channel quality indicator (CQI)
current operating band
signal threshold crossing notifications

Imported Objects

From CISCO-SMI

ciscoMgmt

OBJECT-IDENTITY

From CISCO-WAN-3G-MIB

C3gServiceCapability

From ENTITY-MIB

entPhysicalIndex	OBJECT-TYPE
entPhysicalName	OBJECT-TYPE

From IF-MIB

ifIndex

OBJECT-TYPE

From INET-ADDRESS-MIB

InetAddress
InetAddressType

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter64
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

RowStatus
StorageType
TEXTUAL-CONVENTION

How to Use in IPNetwork Monitor

Example using cwceLteEpsTotalBytesTx OID:

Select a Cisco IR8xx/IR1101 series industrial router (4G/LTE) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type cwceLteEpsTotalBytesTx into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. This object indicates the total data bytes transmitted by this bearer. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter64-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline (in bytes), since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
ciscoWanCellExtLte	1.3.6.1.4.1.9.9.817.1.1
ciscoWanCellExtMIB	1.3.6.1.4.1.9.9.817			This MIB module is an extension of CISCO-WAN-3G-MIB.my, and it provides network management support for Cisco cellular WAN 4G/LTE products. * ABBREVIATIONS, ACRONYMS, AND SYMBOLS * AMBR - Aggregate Maximum Bit Rate APN - Access Point Name ARP - Allocation and Retention Priority CQI - Channel Quality Indicator eNodeB - Evolved Node B EPS - Evolved Packet System E-UTRAN - Evolved Universal Terrestrial Radio Access GBR - Guaranteed Bit Rate LTE - Long Term Evolution MBR - Maximum Bit Rate PCRF - Policy and Charging Rules Function PDN - Packet Data Network QCI - QoS Class Identifier QOS - Quality of Service RF - Radio Frequency RSRP - Reference Signal Receive Power RSRQ - Reference Signal Receive Quality SINR - Signal-to-Interference plus Noise Ratio SNR - Signal-to-Noise Ratio UE - User Equipment
ciscoWanCellExtMIBCompliance	1.3.6.1.4.1.9.9.817.2.1.1			The compliance statement for the CISCO-WAN-CELL-EXT-MIB.
ciscoWanCellExtMIBCompliances	1.3.6.1.4.1.9.9.817.2.1
ciscoWanCellExtMIBConform	1.3.6.1.4.1.9.9.817.2
ciscoWanCellExtMIBGroups	1.3.6.1.4.1.9.9.817.2.2
ciscoWanCellExtMIBLteObjectGroup	1.3.6.1.4.1.9.9.817.2.2.1			A collection of objects for Cellular 4G/LTE.
ciscoWanCellExtMIBNotificationGroup	1.3.6.1.4.1.9.9.817.2.2.2			A collection of objects for Cellular WAN notifications.
ciscoWanCellExtMIBNotifs	1.3.6.1.4.1.9.9.817.0
ciscoWanCellExtMIBObjects	1.3.6.1.4.1.9.9.817.1
CIS cwceLteCurrCqiIndex	1.3.6.1.4.1.9.9.817.1.1.1.1.1.5	CiscoWanCellExtCqiIndex	read-only	This object indicates he LTE CQI Index reported by the modem.
U32 cwceLteCurrOperatingBand	1.3.6.1.4.1.9.9.817.1.1.1.1.1.6	Unsigned32	read-only	This object indicates the E-UTRAN Operating Band reported by the modem.
CIS cwceLteCurrRsrp	1.3.6.1.4.1.9.9.817.1.1.1.1.1.1	CiscoWanCellExtRsrp	read-only	This object indicates the LTE RSRP value reported by the modem.
CIS cwceLteCurrRsrq	1.3.6.1.4.1.9.9.817.1.1.1.1.1.2	CiscoWanCellExtRsrq	read-only	This object indicates the LTE RSRQ value reported by the modem.
CIS cwceLteCurrSinr	1.3.6.1.4.1.9.9.817.1.1.1.1.1.4	CiscoWanCellExtSINR	read-only	This object indicates the LTE SINR value measured in decibels (dB) reported by the modem.
CIS cwceLteCurrSnr	1.3.6.1.4.1.9.9.817.1.1.1.1.1.3	CiscoWanCellExtSNR	read-only	This object indicates the LTE SNR value reported by the modem.
U32 cwceLteEpsAmbr	1.3.6.1.4.1.9.9.817.1.1.2.5.1.8	Unsigned32	read-only	This object indicates the Aggregated Maximum Bit Rate. This object is valid only if the value of the corresponding cwceLteEpsBearerResType is 'defaultBearer'.
U32 cwceLteEpsArp	1.3.6.1.4.1.9.9.817.1.1.2.5.1.4	Unsigned32	read-only	This object indicates the Allocation and Retention Priority(ARP). ARP is a QoS parameter designed to facilitate decisions as to whether a bearer establishment/modification request can be accepted.
U32 cwceLteEpsBearerId	1.3.6.1.4.1.9.9.817.1.1.2.5.1.1	Unsigned32	not-accessible	This object indicates the EPS Bearer Identity which is allocated by the Mobility Management Entity (MME).
cwceLteEpsBearerQosEntry	1.3.6.1.4.1.9.9.817.1.1.2.5.1		not-accessible	An entry contains management information of Cellular 4G/LTE QoS parameters. An entry of this table is created if an interface capable of providing operational Cellular 4G/LTE QoS parameters is detected by the agent. An entry of this table is deleted by the agent if the corresponding entry in ifTable is removed.
cwceLteEpsBearerQosTable	1.3.6.1.4.1.9.9.817.1.1.2.5		not-accessible	This table contains 4G/LTE QoS parameters requested by modem to the cellular network via PDN Context Activation Request message.
INT cwceLteEpsBearerResType	1.3.6.1.4.1.9.9.817.1.1.2.5.1.5	INTEGER	read-only	This object indicates the Bearer resource type.
INT cwceLteEpsBearerType	1.3.6.1.4.1.9.9.817.1.1.2.5.1.2	INTEGER	read-only	This object indicates the type of bearers. gbr - Guaranteed Bit Rate(GBR). GBR bearer has a minimum amount of bandwidth that is reserved by the network, and these resources are always consumed in a radio base station regardless of whether it is used or not. nonGbr - non-Guaranteed Bit Rate(Non-GBR). Non-GBR bearers are for best-effort services and do not consume any network resources. unknown - the type of bearers is unknown.
U32 cwceLteEpsGbr	1.3.6.1.4.1.9.9.817.1.1.2.5.1.6	Unsigned32	read-only	This object indicates the Guaranteed Bit Rate(GBR) which determines the resource reservation to guarantee a given data rate.
U32 cwceLteEpsMbr	1.3.6.1.4.1.9.9.817.1.1.2.5.1.7	Unsigned32	read-only	This object indicates the Maximum Bit Rate(MBR) which is used for policing the user traffic.
C64 cwceLteEpsPacketsRx	1.3.6.1.4.1.9.9.817.1.1.2.5.1.12	Counter64	read-only	This object indicates the number of packets received by this bearer.
C64 cwceLteEpsPacketsTx	1.3.6.1.4.1.9.9.817.1.1.2.5.1.11	Counter64	read-only	This object indicates the number of packets transmitted by this bearer.
U32 cwceLteEpsQCI	1.3.6.1.4.1.9.9.817.1.1.2.5.1.3	Unsigned32	read-only	This object indicates the QoS Class Identifier(QCI). The QCI along with the ARP characterizes the QoS of the bearer.
C64 cwceLteEpsTotalBytesRx	1.3.6.1.4.1.9.9.817.1.1.2.5.1.10	Counter64	read-only	This object indicates the total data bytes received by this bearer.
C64 cwceLteEpsTotalBytesTxEx	1.3.6.1.4.1.9.9.817.1.1.2.5.1.9	Counter64	read-only	This object indicates the total data bytes transmitted by this bearer.
IPt cwceLteIpv4AddrType	1.3.6.1.4.1.9.9.817.1.1.2.1	InetAddressType	read-only	The object indicates the type of Internet address for IPv4 addresses used by profiles and PDNs. The valid value for this object is ipv4(1).
IPt cwceLteIpv6AddrType	1.3.6.1.4.1.9.9.817.1.1.2.2	InetAddressType	read-only	The object indicates the type of Internet address for IPv6 addresses used by profiles and PDNs. The valid value for this object is ipv6(2).
CIS cwceLteNotifRsrp	1.3.6.1.4.1.9.9.817.1.1.1.1.1.7	CiscoWanCellExtRsrp	read-only	This object indicates the LTE RSRP value reported by the modem which triggered the most recent cwceLteRsrpOnsetNotif or cwceLteRsrpAbateNotif notification.
CIS cwceLteNotifRsrq	1.3.6.1.4.1.9.9.817.1.1.1.1.1.8	CiscoWanCellExtRsrq	read-only	This object indicates the LTE RSRP value reported by the modem which triggered the most recent cwceLteRsrqOnsetNotif or cwceLteRsrqAbateNotif notification.
INT cwceLtePdnConnStatus	1.3.6.1.4.1.9.9.817.1.1.2.4.1.3	INTEGER	read-only	This object indicates PDN session status of the profile. This is active when the call is established and PDN context has become active.
cwceLtePdnEntry	1.3.6.1.4.1.9.9.817.1.1.2.4.1		not-accessible	An entry contains management information of Cellular 4G/LTE PDN parameters. An entry of this table is created if an interface capable of providing operational Cellular 4G/LTE PDN parameters is detected by the agent. An entry of this table is deleted by the agent if the corresponding entry in ifTable is removed.
IP cwceLtePdnIpv4Addr	1.3.6.1.4.1.9.9.817.1.1.2.4.1.5	InetAddress	read-only	This object indicates current session EPS Bearer IPv4 address. The type of this address is determined by the value of the cwceLteIpv4AddrType object.
IP cwceLtePdnIpv6Addr	1.3.6.1.4.1.9.9.817.1.1.2.4.1.6	InetAddress	read-only	This object indicates current session EPS Bearer IPv6 address. The type of this address is determined by the value of the cwceLteIpv6AddrType object.
IP cwceLtePdnPriDnsIpv4Addr	1.3.6.1.4.1.9.9.817.1.1.2.4.1.7	InetAddress	read-only	This object indicates current session EPS Bearer Primary DNS IPv4 address. The type of this address is determined by the value of the cwceLteIpv4AddrType object.
IP cwceLtePdnPriDnsIpv6Addr	1.3.6.1.4.1.9.9.817.1.1.2.4.1.9	InetAddress	read-only	This object indicates current session EPS Bearer Primary DNS IPv6 address. The type of this address is determined by the value of the cwceLteIpv6AddrType object.
U32 cwceLtePdnProfileUsed	1.3.6.1.4.1.9.9.817.1.1.2.4.1.2	Unsigned32	read-only	This object indicates the cwceLteProfileIndex of the profile used by current EPS bearer to establish data connection.
IP cwceLtePdnSecDnsIpv4Addr	1.3.6.1.4.1.9.9.817.1.1.2.4.1.8	InetAddress	read-only	This object indicates current session EPS Bearer Secondary DNS IPv4 address. The type of this address is determined by the value of the cwceLteIpv4AddrType object.
IP cwceLtePdnSecDnsIpv6Addr	1.3.6.1.4.1.9.9.817.1.1.2.4.1.10	InetAddress	read-only	This object indicates current session EPS Bearer Secondary DNS IPv6 address. The type of this address is determined by the value of the cwceLteIpv6AddrType object.
cwceLtePdnTable	1.3.6.1.4.1.9.9.817.1.1.2.4		not-accessible	This table contains Cellular 4G/LTE Packet Data Network(PDN) information of all the PDN capable interfaces in the system.
CIS cwceLtePdnType	1.3.6.1.4.1.9.9.817.1.1.2.4.1.4	CiscoWanCellExtProtocolType	read-only	This object indicates current session PDN type.
cwceLteProfile	1.3.6.1.4.1.9.9.817.1.1.2
STR cwceLteProfileApn	1.3.6.1.4.1.9.9.817.1.1.2.3.1.5	SnmpAdminString	read-create	This object specifies configured profile of Access Point Name (APN). The value of this object should be provided by the APN service provider.
U32 cwceLteProfileApnAmbr	1.3.6.1.4.1.9.9.817.1.1.2.3.1.6	Unsigned32	read-create	This object specifies the profile APN-AMBR. APN-AMBR is aggregate bit rate across all Non-GBR bearers and across all PDN connections of the same APN. The value APN-AMBR is a parameter which is defined as part of a user's subscription, but may be overridden by the PCRF.
cwceLteProfileEntry	1.3.6.1.4.1.9.9.817.1.1.2.3.1		not-accessible	An entry contains management information of Cellular 4G/LTE profile parameters. Entries in this table can be created or deleted using cwceLteProfileRowStatus object. An entry of this table is deleted by the agent if the corresponding entry in entPhysicalTable is removed.
U32 cwceLteProfileIndex	1.3.6.1.4.1.9.9.817.1.1.2.3.1.1	Unsigned32	not-accessible	This object specifies profile index, combined with entPhysicalIndex to access profile table.
IP cwceLteProfileIPv4Addr	1.3.6.1.4.1.9.9.817.1.1.2.3.1.3	InetAddress	read-create	This object specifies the configured EPS Bearer IPv4 address. The type of this address is determined by the value of the cwceLteIpv4AddrType object. This object is valid only if the corresponding instance value of cwceLteProfileType is either 'ipv4' or 'ipv4V6'.
IP cwceLteProfileIPv6Addr	1.3.6.1.4.1.9.9.817.1.1.2.3.1.4	InetAddress	read-create	This object specifies the configured EPS Bearer IPv6 address. The type of this address is determined by the value of the cwceLteIpv6AddrType object. This object is valid only if the corresponding instance value of cwceLteProfileType is either 'ipv6' or 'ipv4V6'.
ROW cwceLteProfileRowStatus	1.3.6.1.4.1.9.9.817.1.1.2.3.1.8	RowStatus	read-create	This object specifies the status of the conceptual row. It's used to manage creation, modification and deletion of rows in this table. When a row is active, user cannot modify the value of the objects in that row. All objects in this row need to have valid value before the row can be active.
STO cwceLteProfileStorage	1.3.6.1.4.1.9.9.817.1.1.2.3.1.7	StorageType	read-create	This object specifies the storage type for this conceptual row.
cwceLteProfileTable	1.3.6.1.4.1.9.9.817.1.1.2.3		not-accessible	This table contains Cellular LTE PDN profiles. Cellular device contains multiple profile entries which can be used to establish cellular data connections (PDN contexts). Users can choose any of available PDN profiles to establish data connections. Data connections are described in cwcePacketLteSessionTable. This table is valid only in 4G/LTE Technology mode.
CIS cwceLteProfileType	1.3.6.1.4.1.9.9.817.1.1.2.3.1.2	CiscoWanCellExtProtocolType	read-create	This object specifies the configured EPS Bearer type.
cwceLteRadio	1.3.6.1.4.1.9.9.817.1.1.1
cwceLteRadioEntry	1.3.6.1.4.1.9.9.817.1.1.1.1.1		not-accessible	An entry contains management information of Cellular 4G/LTE Radio signal parameters and notification information. An entry of this table is created if an entity capable of providing operational Cellular 4G/LTE Radio signal parameters and administrative notification information is detected by the agent. An entry of this table is deleted by the agent if the corresponding entry in entPhysicalTable is removed.
cwceLteRadioHistory	1.3.6.1.4.1.9.9.817.1.1.1.2
cwceLteRadioHistoryRsrpEntry	1.3.6.1.4.1.9.9.817.1.1.1.2.1.1		not-accessible	An entry contains management information of Cellular 4G/LTE RSRP Radio history parameters. An entry of this table is created if an entity capable of providing operational Cellular 4G/LTE RSRP Radio history is detected by the agent. An entry of this table is deleted by the agent if the corresponding entry in entPhysicalTable is removed.
OCT cwceLteRadioHistoryRsrpPerHour	1.3.6.1.4.1.9.9.817.1.1.1.2.1.1.3	OCTET STRING	read-only	This object indicates per-hour weakest RSRP value history. It contains a per-hour history of weakest RSRP values for the last 72 hours. The octet in the string is the weakest RSRP value measured in an hour interval.
OCT cwceLteRadioHistoryRsrpPerMinute	1.3.6.1.4.1.9.9.817.1.1.1.2.1.1.2	OCTET STRING	read-only	This object indicates per-minute weakest RSRP value history. It contains a per-minute history of weakest RSRP values for the last 60 minutes. The octet in the string is the weakest RSRP value measured in a minute interval.
OCT cwceLteRadioHistoryRsrpPerSecond	1.3.6.1.4.1.9.9.817.1.1.1.2.1.1.1	OCTET STRING	read-only	This object indicates per-second RSRP history. It contains a per-second history of RSRP values for the last 60 seconds.
cwceLteRadioHistoryRsrpTable	1.3.6.1.4.1.9.9.817.1.1.1.2.1		not-accessible	This table contains Cellular 4G/LTE RSRP history. The history of RSRP are carried in an octet of string. Each octet in the octet string has a value from 40 to 140 and the 150 value is reserved to indicate an uninitialized (Invalid) value. The format of the octet string with n octets is as following: [ octet 0 is latest, octet 1 is latest-1, . . octet n-2 is oldest-1, octet n-1 is oldest ] To convert the provided value into dBm the following formula should be used: dBm = (-1)*value
cwceLteRadioHistoryRsrqEntry	1.3.6.1.4.1.9.9.817.1.1.1.2.2.1		not-accessible	An entry contains management information of Cellular 4G/LTE RSRQ Radio history parameters. An entry of this table is created if an entity capable of providing operational Cellular 4G/LTE RSRQ Radio history is detected by the agent. An entry of this table is deleted by the agent if the corresponding entry in entPhysicalTable is removed.
OCT cwceLteRadioHistoryRsrqPerHour	1.3.6.1.4.1.9.9.817.1.1.1.2.2.1.3	OCTET STRING	read-only	This object indicates per-hour weakest RSRQ value history. It contains a per-hour history of weakest RSRQ values for the last 72 hours. The octet in the string is the weakest RSRQ value measured in an hour interval.
OCT cwceLteRadioHistoryRsrqPerMinute	1.3.6.1.4.1.9.9.817.1.1.1.2.2.1.2	OCTET STRING	read-only	This object indicates per-minute weakest RSRQ value history. It contains a per-minute history of weakest RSRQ values for the last 60 minutes. The octet in the string is the weakest RSRQ value measured in a minute interval.
OCT cwceLteRadioHistoryRsrqPerSecond	1.3.6.1.4.1.9.9.817.1.1.1.2.2.1.1	OCTET STRING	read-only	This object indicates per-second RSRQ history. It contains a per-second history of RSRQ values for the last 60 seconds.
cwceLteRadioHistoryRsrqTable	1.3.6.1.4.1.9.9.817.1.1.1.2.2		not-accessible	This table contains Cellular 4G/LTE RSRQ history. The history of RSRQ are carried in an octet of string. Each octet in the octet string has a value from 3 to 20 and the 25 value is reserved to indicate an uninitialized (Invalid) value. The format of the octet string with n octets is as following: [ octet 0 is latest, octet 1 is latest-1, . . octet n-2 is oldest-1, octet n-1 is oldest ] To convert the provided value into dB the following formula should be used: dB = (-1)*value
cwceLteRadioTable	1.3.6.1.4.1.9.9.817.1.1.1.1		not-accessible	This table contains entPhysicalTable entries which are capable of providing operational Cellular 4G/LTE Radio signal parameters and administrative notification information.
NTF cwceLteRsrpAbateNotif	1.3.6.1.4.1.9.9.817.0.4			If RSRP goes above cwceLteRsrqAbateNotifThreshold and the service bit in cwceLteRsrpOnsetNotifFlag is set, this notification will be generated. Object cwceLteRsrpAbateNotifFlag will indicate which service generates this notification and the associated RSRP will be reported in cwceLteNotifRsrp. Please note that cwceLteNotifRsrp is used to indicate the RSRP value that triggers the notification, user should go to the corresponding radio table to get the current RSRP value.
C3G cwceLteRsrpAbateNotifFlag	1.3.6.1.4.1.9.9.817.1.1.1.1.1.14	C3gServiceCapability	read-write	This object specifies the flag bitmap to control the generation of notification cwceLteRsrpAbateNotif. Each bit represents a service as defined in C3gServiceCapability, set the bit value to 1 to enable (and 0 to disable) the generation of notification cwceLteRsrpAbateNotif for that service. The default value of this object is all bits are 0. Notifications are not generated in technology modes where RSRP is not relevant.
CIS cwceLteRsrpAbateNotifThreshold	1.3.6.1.4.1.9.9.817.1.1.1.1.1.10	CiscoWanCellExtRsrp	read-write	This object specifies the RSRP abate threshold value. If the value of cwceLteCurrRsrp goes above the threshold and the service bit in cwceLteRsrpOnsetNotifFlag is set, the cwceLteRsrpAbateNotif notification for that service will be sent. The absolute value of cwceLteRsrpAbateNotifThreshold should be less than or equal to the absolute value of cwceLteRsrpOnsetNotifThreshold (\|cwceLteRsrpAbateNotifThreshold\| <= \|cwceLteRsrpOnsetNotifThreshold\|).
NTF cwceLteRsrpOnsetNotif	1.3.6.1.4.1.9.9.817.0.3			If RSRP goes below cwceLteRsrpOnsetNotifThreshold and the service bit in cwceLteRsrpOnsetNotifFlag is set, this notification will be generated. Object cwceLteRsrpOnsetNotifFlag will indicate which service generates this notification and the associated RSRP will be reported in cwceLteNotifRsrp. Please note that cwceLteNotifRsrp is used to indicate the RSRP value that triggers the notification, user should go to the corresponding radio table to get the current RSRP value.
C3G cwceLteRsrpOnsetNotifFlag	1.3.6.1.4.1.9.9.817.1.1.1.1.1.13	C3gServiceCapability	read-write	This object specifies the flag bitmap to control the generation of notification cwceLteRsrpOnsetNotif. Each bit represents a service as defined in C3gServiceCapability, set the bit value to 1 to enable (and 0 to disable) the generation of notification cwceLteRsrpOnsetNotif for that service. The default value of this object is all bits are 0. Notifications are not generated in technology modes where RSRP is not relevant.
CIS cwceLteRsrpOnsetNotifThreshold	1.3.6.1.4.1.9.9.817.1.1.1.1.1.9	CiscoWanCellExtRsrp	read-write	This object specifies the RSRP onset threshold value. If the value of cwceLteCurrRsrp goes below the threshold and the service bit in cwceLteRsrpOnsetNotifFlag is set, the cwceLteRsrqOnsetNotif notification for that service will be sent. The absolute value of cwceLteRsrpAbateNotifThreshold should be less than or equal to the absolute value of cwceLteRsrpOnsetNotifThreshold (\|cwceLteRsrpAbateNotifThreshold\| <= \|cwceLteRsrpOnsetNotifThreshold\|).
NTF cwceLteRsrqAbateNotif	1.3.6.1.4.1.9.9.817.0.2			If RSRQ goes above cwceLteRsrqAbateNotifThreshold and the service bit in cwceLteRsrqOnsetNotifFlag is set, this notification will be generated. Object cwceLteRsrqAbateNotifFlag will indicate which service generates this notification and the associated RSRQ will be reported in cwceLteNotifRsrq. Please note that cwceLteNotifRsrq is used to indicate the RSRQ value that triggers the notification, user should go to the corresponding radio table to get the current RSRQ value.
C3G cwceLteRsrqAbateNotifFlag	1.3.6.1.4.1.9.9.817.1.1.1.1.1.16	C3gServiceCapability	read-write	This object specifies the flag bitmap to control the generation of notification cwceLteRsrqAbateNotif. Each bit represents a service as defined in C3gServiceCapability, set the bit value to 1 to enable (and 0 to disable) the generation of notification cwceLteRsrqAbateNotif for that service. The default value of this object is all bits are 0. Notifications are not generated in technology modes where RSRQ is not relevant.
CIS cwceLteRsrqAbateNotifThreshold	1.3.6.1.4.1.9.9.817.1.1.1.1.1.12	CiscoWanCellExtRsrq	read-write	This object specifies the RSRQ abate threshold value. If the value of cwceLteCurrRsrq goes above the threshold and the service bit in cwceLteRsrqOnsetNotifFlag is set, the cwceLteRsrqAbateNotif notification for that service will be sent. The absolute value of cwceLteRsrqAbateNotifThreshold should be less than or equal to the absolute value of cwceLteRsrqOnsetNotifThreshold (\|cwceLteRsrqAbateNotifThreshold\| <= \|cwceLteRsrqOnsetNotifThreshold\|).
NTF cwceLteRsrqOnsetNotif	1.3.6.1.4.1.9.9.817.0.1			If RSRQ goes below cwceLteRsrqOnsetNotifThreshold and the service bit in cwceLteRsrqOnsetNotifFlag is set, this notification will be generated. Object cwceLteRsrqOnsetNotifFlag will indicate which service generates this notification and the associated RSRQ will be reported in cwceLteNotifRsrq. Please note that cwceLteNotifRsrq is used to indicate the RSRQ value that triggers the notification, user should go to the corresponding radio table to get the current RSRQ value.
C3G cwceLteRsrqOnsetNotifFlag	1.3.6.1.4.1.9.9.817.1.1.1.1.1.15	C3gServiceCapability	read-write	This object specifies the flag bitmap to control the generation of notification cwceLteRsrqOnsetNotif. Each bit represents a service as defined in C3gServiceCapability, set the bit value to 1 to enable (and 0 to disable) the generation of notification cwceLteRsrqOnsetNotif for that service. The default value of this object is all bits are 0. Notifications are not generated in technology modes where RSRQ is not relevant.
CIS cwceLteRsrqOnsetNotifThreshold	1.3.6.1.4.1.9.9.817.1.1.1.1.1.11	CiscoWanCellExtRsrq	read-write	This object specifies the RSRQ onset threshold value. If the value of cwceLteCurrRsrq goes below the threshold and the service bit in cwceLteRsrqOnsetNotifFlag is set, the cwceLteRsrqOnsetNotif notification for that service will be sent. The absolute value of cwceLteRsrqAbateNotifThreshold should be less than or equal to the absolute value of cwceLteRsrqOnsetNotifThreshold (\|cwceLteRsrqAbateNotifThreshold\| <= \|cwceLteRsrqOnsetNotifThreshold\|).

RFC description

Cisco vendor-private MIB for managing 4G/LTE cellular WAN interfaces and mobile broadband connectivity on routers.

Start monitoring Cisco IR8xx/IR1101 series industrial routers (4G/LTE) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CISCO-WAN-CELL-EXT-MIB