| OID symbolic | OID numeric | Type | Access | Description |
|---|
| NTF circuitActive | 1.3.6.1.4.1.5812.0.25 | | | Indicates that the circuit became active |
| INT circuitAdminState | 1.3.6.1.4.1.5812.6.8.1.35 | INTEGER | read-write | Administrative state of the circuit. Circuits in the
disabled state do not consume network resources such as
bandwidth. The network continuously attempts to establish
circuits until successful while in the enabled state. The
'enabledButNotUsed' state tells that the transport segment
is established and network resources are assigned to it,
but, traffic is not allowed to pass though it. |
| U32 circuitBwdTDParam1 | 1.3.6.1.4.1.5812.6.8.1.30 | Unsigned32 | read-write | Parameter 1 of the backward traffic descriptor of
type circuitBwdTdType.
For type Ethernet, this value corresponds to CIR.
For type Frame Relay, this value corresponds to CIR.
For type ATM-CBR, this value corresponds to PCR(0+1). |
| U32 circuitBwdTDParam2 | 1.3.6.1.4.1.5812.6.8.1.31 | Unsigned32 | read-write | Parameter 2 of the backward traffic descriptor of
type circuitBwdTdType.
For type Ethernet, this value corresponds to Bc.
For type Frame Relay, this value corresponds to Bc. |
| U32 circuitBwdTDParam3 | 1.3.6.1.4.1.5812.6.8.1.32 | Unsigned32 | read-write | Parameter 3 of the backward traffic descriptor of
type circuitBwdTdType.
For type Ethernet, this value corresponds to Be.
For type Frame Relay, this value corresponds to Be. |
| U32 circuitBwdTDParam4 | 1.3.6.1.4.1.5812.6.8.1.33 | Unsigned32 | read-write | Parameter 4 of the backward traffic descriptor of
type circuitBwdTdType. |
| INT circuitBwdTDType | 1.3.6.1.4.1.5812.6.8.1.29 | INTEGER | read-write | Specifies the traffic descriptor type associated with
the backward traffic descriptor parameters. The backward
direction is 'out of the network' from the circuit endpoint.
TDType is independent to of the end-point protocol. |
| INT circuitClassOfService | 1.3.6.1.4.1.5812.6.8.1.34 | INTEGER | read-write | Specifies the class of service for Data or non-TDM
circuits. This value is in the range of 0-7 where 1
has the highest priority and 7 has the lowest. |
| U32 circuitDestConnectionID | 1.3.6.1.4.1.5812.6.8.1.7 | Unsigned32 | read-write | Connection Identifier of the destination circuit endpoint.
Based on the protocol type, further information may
be required to completely specify a circuit on a channel.
For example, Ethernet VLAN requires a VLAN Id, Frame Relay
requires a DLCI and ATM requires VPI and VCI. For ATM, this
field is encoded as 12 bits of VPI and 16 bits of VCI. |
| OCT circuitDestDescString | 1.3.6.1.4.1.5812.6.8.1.8 | OCTET STRING | read-only | Textual description of the destination side of the circuit endpoint. |
| U32 circuitDestInterfaceNum | 1.3.6.1.4.1.5812.6.8.1.6 | Unsigned32 | read-write | The interface number of the destination circuit endpoint. |
| IP circuitDestIpAddr | 1.3.6.1.4.1.5812.6.8.1.5 | IpAddress | read-write | IP address of the destination circuit endpoint. |
| INT circuitEndPoint1Protocol | 1.3.6.1.4.1.5812.6.8.1.22 | INTEGER | read-write | Protocol determines the connectionID. |
| INT circuitEndPoint2Protocol | 1.3.6.1.4.1.5812.6.8.1.28 | INTEGER | read-write | Protocol determines the connectionID. |
| circuitEntry | 1.3.6.1.4.1.5812.6.8.1 | | not-accessible | Entry in the table for a single transport channel |
| U32 circuitEventInterval | 1.3.6.1.4.1.5812.6.6 | Unsigned32 | read-write | For any circuit related events, events are generated at a specific
time interval. circuitEventInterval specifies that. The default value
is 1 second. |
| INT circuitEventNumPerInterval | 1.3.6.1.4.1.5812.6.7 | INTEGER | read-write | This object specifies the number of events generated per interval.
The default is 10 per second. |
| U32 circuitFailLocConnectionID1 | 1.3.6.1.4.1.5812.6.8.1.17 | Unsigned32 | read-only | Connection Identifier of the failed circuit endpoint. |
| U32 circuitFailLocConnectionID2 | 1.3.6.1.4.1.5812.6.8.1.21 | Unsigned32 | read-only | Connection Identifier of the failed circuit endpoint. |
| U32 circuitFailLocInterfaceNum1 | 1.3.6.1.4.1.5812.6.8.1.16 | Unsigned32 | read-only | Interface number where circuit failure code is
encountered. |
| U32 circuitFailLocInterfaceNum2 | 1.3.6.1.4.1.5812.6.8.1.20 | Unsigned32 | read-only | Interface number where circuit failure code is
encountered. |
| IP circuitFailLocIpAddr | 1.3.6.1.4.1.5812.6.8.1.13 | IpAddress | read-only | IP address of location where circuit failure code is
encountered. |
| INT circuitFailLocPort1 | 1.3.6.1.4.1.5812.6.8.1.15 | INTEGER | read-only | Port number where circuit failure code is
encountered. |
| INT circuitFailLocPort2 | 1.3.6.1.4.1.5812.6.8.1.19 | INTEGER | read-only | Port number where circuit failure code is
encountered. |
| INT circuitFailLocSlot1 | 1.3.6.1.4.1.5812.6.8.1.14 | INTEGER | read-only | Slot number where circuit failure code is
encountered. |
| INT circuitFailLocSlot2 | 1.3.6.1.4.1.5812.6.8.1.18 | INTEGER | read-only | Slot number where circuit failure code is
encountered. |
| U32 circuitFwdTDParam1 | 1.3.6.1.4.1.5812.6.8.1.24 | Unsigned32 | read-write | Parameter 1 of the forward traffic descriptor of
type circuitFwdTdType.
For type Ethernet, this value corresponds to CIR.
For type Frame Relay, this value corresponds to CIR.
For type ATM-CBR, this value corresponds to PCR(0+1). |
| U32 circuitFwdTDParam2 | 1.3.6.1.4.1.5812.6.8.1.25 | Unsigned32 | read-write | Parameter 2 of the forward traffic descriptor of
type circuitFwdTdType.
For type Ethernet, this value corresponds to Bc.
For type Frame Relay, this value corresponds to Bc. |
| U32 circuitFwdTDParam3 | 1.3.6.1.4.1.5812.6.8.1.26 | Unsigned32 | read-write | Parameter 3 of the forward traffic descriptor of
type circuitFwdTdType.
For type Ethernet, this value corresponds to Be.
For type Frame Relay, this value corresponds to Be. |
| U32 circuitFwdTDParam4 | 1.3.6.1.4.1.5812.6.8.1.27 | Unsigned32 | read-write | Parameter 4 of the forward traffic descriptor of
type circuitFwdTdType. |
| INT circuitFwdTDType | 1.3.6.1.4.1.5812.6.8.1.23 | INTEGER | read-write | Specifies the traffic descriptor type associated with
the forward traffic descriptor parameters. The forward
direction is 'into the network' from the circuit endpoint.
TDType is independent of the end-point protocol. |
| U32 circuitHoldPriority | 1.3.6.1.4.1.5812.6.8.1.39 | Unsigned32 | read-only | If a number of transport channels of a low Setup Priority need
to be cleared in order to release resources allowing for a higher priority
(Setup) transport channel to be established, this field specifies the
Hold priority where low Hold priority transport channels
are cleared before higher Hold priority transport channels. |
| U32 circuitID | 1.3.6.1.4.1.5812.6.8.1.10 | Unsigned32 | read-only | CircuitID is a unique ID given to a circuit. It is
equal to the TC-ID in the PM. |
| NTF circuitInactive | 1.3.6.1.4.1.5812.0.24 | | | Indicates that the circuit became inactive and specifies the reason for it becoming inactive |
| C64 circuitInCLP0Cells | 1.3.6.1.4.1.5812.6.8.1.52 | Counter64 | read-only | Number of cells received at the ingress point and passed
on to the circuit. |
| C64 circuitInCLP0CellsDiscard | 1.3.6.1.4.1.5812.6.8.1.58 | Counter64 | read-only | Number of octets received at the ingress point but are
discarded due to the non-conformance of the contract, i.e.,
it exceeds the traffic contract (BE). |
| C64 circuitInCLP0CellsTagged | 1.3.6.1.4.1.5812.6.8.1.62 | Counter64 | read-only | Number of tagged octets received. A tagged octet
represents non-conforming octet to the contract
(when CIR < octet contract < BE).In these octets,
the DE (Discard Enable) is set. |
| C64 circuitInCLP1Cells | 1.3.6.1.4.1.5812.6.8.1.53 | Counter64 | read-only | Number of cells received at the ingress point and passed
on to the circuit. |
| C64 circuitInCLP1CellsDiscard | 1.3.6.1.4.1.5812.6.8.1.59 | Counter64 | read-only | Number of octets received at the ingress point but are
discarded due to the non-conformance of the contract, i.e.,
it exceeds the traffic contract (BE). |
| C64 circuitInDEFrames | 1.3.6.1.4.1.5812.6.8.1.49 | Counter64 | read-only | Number of frames received at the ingress point and passed
on to the circuit. |
| C64 circuitInDEFramesDiscard | 1.3.6.1.4.1.5812.6.8.1.55 | Counter64 | read-only | Number of frames received at the ingress point but are
discarded due to the non-conformance of the contract, i.e.,
it exceeds the traffic contract (BE). |
| C64 circuitInDEOctets | 1.3.6.1.4.1.5812.6.8.1.51 | Counter64 | read-only | Number of octets received at the ingress point and passed
on to the circuit. |
| C64 circuitInDEOctetsDiscard | 1.3.6.1.4.1.5812.6.8.1.57 | Counter64 | read-only | Number of octets received at the ingress point but are
discarded due to the non-conformance of the contract, i.e.,
it exceeds the traffic contract (BE). |
| C64 circuitInFrames | 1.3.6.1.4.1.5812.6.8.1.48 | Counter64 | read-only | Number of frames received at the ingress point and passed
on to the circuit. |
| C64 circuitInFramesDiscard | 1.3.6.1.4.1.5812.6.8.1.54 | Counter64 | read-only | Number of frames received at the ingress point but are
discarded due to the non-conformance of the contract, i.e.,
it exceeds the traffic contract (BE). |
| C64 circuitInFramesTagged | 1.3.6.1.4.1.5812.6.8.1.60 | Counter64 | read-only | Number of tagged frames received. A tagged frame
represents non-conforming frames to the contract
(when CIR < frame contract < BE). In these frames,
the DE (Discard Enable) is set. |
| C64 circuitInOctets | 1.3.6.1.4.1.5812.6.8.1.50 | Counter64 | read-only | Number of octets received at the ingress point and passed
on to the circuit. |
| C64 circuitInOctetsDiscard | 1.3.6.1.4.1.5812.6.8.1.56 | Counter64 | read-only | Number of octets received at the ingress point but are
discarded due to the non-conformance of the contract, i.e.,
it exceeds the traffic contract (BE). |
| C64 circuitInOctetsTagged | 1.3.6.1.4.1.5812.6.8.1.61 | Counter64 | read-only | Number of tagged octets received. A tagged octet
represents non-conforming octet to the contract
(when CIR < octet contract < BE).In these octets,
the DE (Discard Enable) is set. |
| T/F circuitIsRedundancyReqd | 1.3.6.1.4.1.5812.6.8.1.40 | TruthValue | read-write | Specifies if the circuit is to be established over rings
that are logically configured as 'protected'. A protected
ring could physically be in a fault state where one fiber
has failed. A circuit that requires redundancy will be
established over rings logically configured as 'protected'
even though the current physical state of a protected ring
may be in a fault state. |
| INT circuitLoadBalanceInterval | 1.3.6.1.4.1.5812.6.2 | INTEGER | read-write | The default load balancing schedule is to examine 1 circuit every 3
minutes at the GNE. Regardless of whether the circuit is moved to a better
ring path or not, the next circuit is not examined until another 3 minutes
(default) had expired. The duration of the load balance timer will be
configurable from a range of 0 to 65535 seconds. Using a value of 0 will
turn off load balancing. |
| INT circuitLoadBalanceNumPerInterval | 1.3.6.1.4.1.5812.6.3 | INTEGER | read-write | Indicates the number of circuits being loadbalanced in a fixed interval.
The maximum value is 10 circuits per second. |
| NTF circuitLoadBalancing | 1.3.6.1.4.1.5812.0.26 | | | Indicates that the circuit underwent load balancing |
| circuitMIB | 1.3.6.1.4.1.5812.6.1 | | | The MIB module for transport channels |
| OCT circuitName | 1.3.6.1.4.1.5812.6.8.1.9 | OCTET STRING | read-write | CircuitName is a unique name given to a circuit. |
| IP circuitNewIpAddrToSwap | 1.3.6.1.4.1.5812.6.5 | IpAddress | read-write | When a chassis running several circuits has to be moved to a new
location with a new different IpAddress, then all the associated circuits
has to be properly modified with the new IpAddress. This object will
specify the old-IpAddress. This process is almost transparent to the user,
but, he will notice traffic loss due to the circuits being brought down
and up. |
| IP circuitOldIpAddrToSwap | 1.3.6.1.4.1.5812.6.4 | IpAddress | read-write | When a chassis running several circuits has to be moved to a new
location with a new different IpAddress, then all the associated circuits
has to be properly modified with the new IpAddress. This object will
specify the old-IpAddress. This process is almost transparent to the user,
but, he will notice traffic loss due to the circuits being brought down
and up. |
| INT circuitOperState | 1.3.6.1.4.1.5812.6.8.1.36 | INTEGER | read-only | Aperational state of the circuit. Circuits in the
disabled state do not consume network resources such as
bandwidth. The network continuously attempts to establish
circuits until successful while in the enabled state. |
| C64 circuitOutCLP0Cells | 1.3.6.1.4.1.5812.6.8.1.67 | Counter64 | read-only | Number of cells sent out through the circuit. |
| C64 circuitOutCLP1Cells | 1.3.6.1.4.1.5812.6.8.1.68 | Counter64 | read-only | Number of cells sent out through the circuit. |
| C64 circuitOutDEFrames | 1.3.6.1.4.1.5812.6.8.1.64 | Counter64 | read-only | Number of frames sent out through the circuit. |
| C64 circuitOutDEOctets | 1.3.6.1.4.1.5812.6.8.1.66 | Counter64 | read-only | Number of octets sent out through the circuit. |
| C64 circuitOutFrames | 1.3.6.1.4.1.5812.6.8.1.63 | Counter64 | read-only | Number of frames sent out through the circuit. |
| C64 circuitOutOctets | 1.3.6.1.4.1.5812.6.8.1.65 | Counter64 | read-only | Number of octets sent out through the circuit. |
| INT circuitPreferredEP1OptPort | 1.3.6.1.4.1.5812.6.8.1.42 | INTEGER | read-write | If the circuit spans one or two rings, this is the port number
of the first preferred ring. |
| INT circuitPreferredEP1OptSlot | 1.3.6.1.4.1.5812.6.8.1.41 | INTEGER | read-write | If the circuit spans one or two rings, this is the slot number
of the first preferred ring. Preferred rings allow a manual overide
of the routed circuit path. |
| INT circuitPreferredEP1OptVport | 1.3.6.1.4.1.5812.6.8.1.43 | INTEGER | read-write | If the circuit spans one or two rings, this is the lambda number
of the first preferred ring. |
| INT circuitPreferredEP2OptPort | 1.3.6.1.4.1.5812.6.8.1.45 | INTEGER | read-write | If the circuit spans two rings, this is the port number
of the second preferred ring. |
| INT circuitPreferredEP2OptSlot | 1.3.6.1.4.1.5812.6.8.1.44 | INTEGER | read-write | If the circuit spans two rings, this is the slot number
of the second preferred ring. Preferred rings allow a manual overide
of the routed circuit path. |
| INT circuitPreferredEP2OptVport | 1.3.6.1.4.1.5812.6.8.1.46 | INTEGER | read-write | If the circuit spans two rings, this is the lambda number
of the second preferred ring. |
| STR circuitReasonText | 1.3.6.1.4.1.5812.6.8.1.12 | DisplayString | read-only | Provides the reason for the error indicated. |
| INT circuitRowStatus | 1.3.6.1.4.1.5812.6.8.1.11 | INTEGER | read-write | Indicates if a row has been created or deleted.
See SNMPv2-TC for complete description. |
| U32 circuitSetupPriority | 1.3.6.1.4.1.5812.6.8.1.38 | Unsigned32 | read-only | If there are insufficient network resources for establishing
all transport channels, this field specifies the priority of the
transport channel. |
| U32 circuitSrcConnectionID | 1.3.6.1.4.1.5812.6.8.1.3 | Unsigned32 | read-write | Connection Identifier of the source circuit endpoint.
Based on the protocol type, further information may
be required to completely specify a circuit on a channel.
For example, Ethernet VLAN requires a VLAN Id, Frame Relay
requires a DLCI and ATM requires VPI and VCI. For ATM, this
field is encoded as 12 bits of VPI and 16 bits of VCI. |
| OCT circuitSrcDescString | 1.3.6.1.4.1.5812.6.8.1.4 | OCTET STRING | read-only | Textual description of the source side of the circuit endpoint. |
| U32 circuitSrcInterfaceNum | 1.3.6.1.4.1.5812.6.8.1.2 | Unsigned32 | read-write | The interface number of the source circuit endpoint. |
| IP circuitSrcIpAddr | 1.3.6.1.4.1.5812.6.8.1.1 | IpAddress | read-write | IP address of the source circuit endpoint. |
| circuitTable | 1.3.6.1.4.1.5812.6.8 | | not-accessible | A table containing information about the transport channels in the system |
| U32 circuitTimeSinceStatusChange | 1.3.6.1.4.1.5812.6.8.1.37 | Unsigned32 | read-only | Gives the time (in seconds) since the most recent status change. |
| INT circuitUseAlternateRing | 1.3.6.1.4.1.5812.6.8.1.47 | INTEGER | read-write | Allows operator to specify whether an alternate ring can
be used if the preferred ring(s) fail. This requires the
ability to load-balance back onto the preferred ring once
it becomes available. The format for this field is Boolean. |
