CDM-570

All MIBs › CDM-570

Organization: Comtech EF Data Corp.

Last Updated: 2006-02-22

Category: Satellite, Vendor: Comtech EF Data

Description: Manages Comtech EF Data CDM-570 satellite modem configuration including modulation, coding rate, and link statistics.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is CDM-570?

The CDM-570 MIB is Comtech EF Data's proprietary module for managing the CDM-570 series of L-Band and IF-Band satellite modems used in VSAT and point-to-point satellite links. It exposes configuration and status data for modulation type, forward error correction/coding rate, transmit/receive frequencies, and link performance statistics such as Eb/No and demodulator lock state. Administrators use it to monitor the hardware and software health of the modem, including unit uptime, current operational state, alarm/fault conditions, and configuration/firmware consistency across a satellite link. Because it manages a physical WAN interface, it typically complements standard IF-MIB/RFC1213 interface counters rather than replacing them. It is deployed on satellite ground stations and remote VSAT terminals where continuous visibility into modem lock status and link quality is critical for maintaining connectivity. Engineers can download the CDM-570 file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in CDM-570. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Comtech EF Data CDM-570 satellite modem (L-Band and IF-Band variants)

Monitoring Examples

No specific object or table names were sampled for this MIB, so no fabricated object names are cited here; based on its stated purpose, an operator would typically poll modem status registers for demodulator lock state, receive signal level, and configured modulation/FEC rate to catch a degrading satellite link before it drops. A sudden loss-of-lock indication combined with falling Eb/No would signal a rain-fade or antenna-pointing problem requiring dispatch.

What Can Be Monitored

demodulator lock status
transmit/receive frequency
modulation and FEC coding rate
Eb/No signal quality
unit uptime
alarm/fault status

Imported Objects

From ComtechEFData

comtechEFData

MODULE-IDENTITY

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE

From SNMPv2-TC

DisplayString
MacAddress

OIDs

OID symbolic	OID numeric	Type	Access	Description
cdm570	1.3.6.1.4.1.6247.24			Module Identity for both CDM-570 L-Band and IF-Band Satellite Modems.
IP cdm570AccessIPAddress	1.3.6.1.4.1.6247.24.1.2.1.5.2.1.2	IpAddress	read-write	The IP addresses that can access the unit. The value of 0.0.0.0 means not defined.
INT cdm570AccessListEnforcement	1.3.6.1.4.1.6247.24.1.2.1.5.1	INTEGER	read-write	Enable or disable enforcement of the the access list. Note: Be sure that you have added the SNMP browser's/manager's IP Address to the access list before enabling access list filtering. Otherwise, the SNMP browser/manager will no longer be able to gain access to the unit.
cdm570AccessListEntry	1.3.6.1.4.1.6247.24.1.2.1.5.2.1		not-accessible	The entry for the access list table.
INT cdm570AccessListIndex	1.3.6.1.4.1.6247.24.1.2.1.5.2.1.1	INTEGER	read-only	The index for the access list from 1..4.
cdm570AccessLists	1.3.6.1.4.1.6247.24.1.2.1.5
cdm570AccessListTable	1.3.6.1.4.1.6247.24.1.2.1.5.2		not-accessible	The table that holds the access list.
INT cdm570AccessSubnetMaskLength	1.3.6.1.4.1.6247.24.1.2.1.5.2.1.3	INTEGER	read-write	The subnet mask length of the IP address for the access list. Subnet mask can be from 8..32. The value of 0 means not defined.
cdm570AlarmMask	1.3.6.1.4.1.6247.24.1.2.7
INT cdm570AlarmMaskBufferSlip	1.3.6.1.4.1.6247.24.1.2.7.7	INTEGER	read-write	Buffer slip alarm mask, where: 0 = Unmasked 1 = Masked
INT cdm570AlarmMaskEbNoAlarm	1.3.6.1.4.1.6247.24.1.2.7.5	INTEGER	read-write	Eb/No alarm mask, where: 0 = Unmasked 1 = Masked
INT cdm570AlarmMaskExtReference	1.3.6.1.4.1.6247.24.1.2.7.8	INTEGER	read-write	External reference alarm mask, where: 0 = Unmasked 1 = Masked
INT cdm570AlarmMaskG703BPV	1.3.6.1.4.1.6247.24.1.2.7.2	INTEGER	read-write	G.703 BPV alarm mask, where: 0 = Unmasked 1 = Masked
INT cdm570AlarmMaskRxAGC	1.3.6.1.4.1.6247.24.1.2.7.4	INTEGER	read-write	Rx AGC alarm mask, where: 0 = Unmasked 1 = Masked
INT cdm570AlarmMaskRxAIS	1.3.6.1.4.1.6247.24.1.2.7.6	INTEGER	read-write	Rx-AIS alarm mask, where: 0 = Unmasked 1 = Masked
INT cdm570AlarmMaskTxAIS	1.3.6.1.4.1.6247.24.1.2.7.3	INTEGER	read-write	Tx-AIS alarm mask, where: 0 = Unmasked 1 = Masked
INT cdm570AlarmMaskTxFIFO	1.3.6.1.4.1.6247.24.1.2.7.1	INTEGER	read-write	Tx FIFO alarm mask, where: 0 = Unmasked 1 = Masked
cdm570Alarms	1.3.6.1.4.1.6247.24.1.3.1
cdm570AUPC	1.3.6.1.4.1.6247.24.1.2.4.3
INT cdm570AUPCActionOnMaxPower	1.3.6.1.4.1.6247.24.1.2.4.3.4	INTEGER	read-write	Defines action on max. power condition, where: 0 = No action 1 = Generate Tx alarm
INT cdm570AUPCActionOnRemoteDemodUnlock	1.3.6.1.4.1.6247.24.1.2.4.3.5	INTEGER	read-write	Defines action on remote demod unlock, where: 0 = Go to nominal power 1 = Go to max power
INT cdm570AUPCEnable	1.3.6.1.4.1.6247.24.1.2.4.3.1	INTEGER	read-write	AUPC mode enable/disable, where: 0 = Disable 1 = Enable Note: To enable AUPC, framing must FIRST be enabled.
cdm570AUPCParams	1.3.6.1.4.1.6247.24.1.3.5
INT cdm570AUPCRemoteDemodEbNo	1.3.6.1.4.1.6247.24.1.3.5.1	INTEGER	read-only	Returns the value of the Eb/No ofthe remote demodulator. Units = 0.1 dB Responds 999 = remote demod unlocked. Responds 0 = EDMAC is disabled.
INT cdm570AUPCRemoteDemodTargetEbNo	1.3.6.1.4.1.6247.24.1.2.4.3.2	INTEGER	read-write	Target Eb/No value for remote demod, from 0.0 to 14.9 dB. Units = 0.1 dB.
INT cdm570AUPCTxPowerIncrease	1.3.6.1.4.1.6247.24.1.3.5.2	INTEGER	read-only	Returns the increase in Tx power level, in 0.1 dB (from the nominal setting) due to the action of AUPC. Responds with 999 if AUPC is disabled.
INT cdm570AUPCTxPowerMaxIncrease	1.3.6.1.4.1.6247.24.1.2.4.3.3	INTEGER	read-write	Max increase in Tx Power permitted, from 0 to 9 dB. Units = dB.
cdm570Buffer	1.3.6.1.4.1.6247.24.1.6.1
INT cdm570BufferFillState	1.3.6.1.4.1.6247.24.1.3.2.2	INTEGER	read-only	Unit returns the value of the buffer fill state, between 1 to 99%. Returns 0 if demodulator is unlocked. Returns -1 if buffer is disabled.
STR cdm570CircuitID	1.3.6.1.4.1.6247.24.1.6.4.1	DisplayString	read-write	Sets or queries the user-defined Circuit ID string, which is a fixed length of 24 characters. Valid characters include: Space ( ) * + - , . / 0 thru 9 and A thru Z
INT cdm570ClearAllStoredEvents	1.3.6.1.4.1.6247.24.1.3.3.2	INTEGER	read-write	Forces the software to clear the event log. This is a command only.
INT cdm570ClearAllStoredStatistics	1.3.6.1.4.1.6247.24.1.3.4.3	INTEGER	read-write	Forces the software to clear the statistics log. This is a command only.
cdm570Compliance	1.3.6.1.4.1.6247.24.3.2.1			CDM-570 (Both L-Band and IF-Band) Compliance.
cdm570Compliances	1.3.6.1.4.1.6247.24.3.2
cdm570Config	1.3.6.1.4.1.6247.24.1.2
INT cdm570ConfigurationLoad	1.3.6.1.4.1.6247.24.1.5.2	INTEGER	read-write	Causes the device to retrieve a previously stored modem configuration from configuration memory location defined by the argument (0 to 9). This is a COMMAND ONLY. Get always responds with 0.
INT cdm570ConfigurationSave	1.3.6.1.4.1.6247.24.1.5.1	INTEGER	read-write	Causes the device to store the current modem configuration in configuration memory location defined by the argument (0 to 9). This is a COMMAND ONLY. Get always responds with 0.
cdm570Conformance	1.3.6.1.4.1.6247.24.3
INT cdm570DataInterface	1.3.6.1.4.1.6247.24.1.2.5.1	INTEGER	read-write	Terrestrial interface type, where: 0 = EIA-422/EIA-530 DCE 1 = V.35 DCE 2 = EIA-232 (sync) 3 = G.703 T1 AMI (forces Rx and Tx data rates to 1544 kbps) 4 = G.703 T1 B8ZS (forces Rx and Tx data rates to 1544 kbps) 5 = G.703 E1 Unbal AMI (forces Rx and Tx data rates to 2048 kbps) 6 = G.703 E1 Unbal HDB3 (forces Rx and Tx data rates to 2048 kbps) 7 = G.703 E1 Bal AMI (forces Rx and Tx data rates to 2048 kbps) 8 = G.703 E1 Bal HDB3 (forces Rx and Tx data rates to 2048 kbps) 9 = IP (Ethernet)
INT cdm570DataRateOption	1.3.6.1.4.1.6247.24.1.1.2.3	INTEGER	read-only	Data rate option, where: 0 = Base (512 kbps) 1 = Up to 2048 kbps 2 = Up to 5000 kbps 3 = Up to 9980 kbps
IP cdm570DefaultGateway	1.3.6.1.4.1.6247.24.1.2.1.3	IpAddress	read-write	The IP address of the default gateway.
cdm570EDMAC	1.3.6.1.4.1.6247.24.1.2.4.2
INT cdm570EDMACAddress	1.3.6.1.4.1.6247.24.1.2.4.2.2	INTEGER	read-write	For a Master, the EDMA Address is the range of addresses of distant-end units (modems or transceivers) which this unit, as the Master, will forward messages for. Only values which are integer multiples of ten are permitted. (10, 20, 30, 40, etc....) For a Slave, the EDMAC address is the address of the slave and is query only.
INT cdm570EDMACMode	1.3.6.1.4.1.6247.24.1.2.4.2.1	INTEGER	read-write	EDMAC mode, where: 0 = EDMAC Idle 1 = EDMAC Master 2 = EDMAC Slave
cdm570EthernetRemoteControl	1.3.6.1.4.1.6247.24.1.2.1
STR cdm570EventDate	1.3.6.1.4.1.6247.24.1.3.3.1.1.2	DisplayString	read-only	The date of the event in the form ddmmyy, where dd = day of the month (01 to 31) mm = month (01 to 12) yy = year (00 to 99)
STR cdm570EventDescription	1.3.6.1.4.1.6247.24.1.3.3.1.1.4	DisplayString	read-only	The event description string with following format: {1 of the following: Clear, Fault, Info} - {Texual Description of Event}
INT cdm570EventIndex	1.3.6.1.4.1.6247.24.1.3.3.1.1.1	INTEGER	read-only	The index for stored events table.
cdm570EventLog	1.3.6.1.4.1.6247.24.1.3.3
STR cdm570EventTime	1.3.6.1.4.1.6247.24.1.3.3.1.1.3	DisplayString	read-only	The time of the event in the form hhmmss, indicating the time from midnight, where: hh = hours (00 to 23) mm = minutes (00 to 59) ss = seconds (00 to 59)
STR cdm570FirmwareRevision	1.3.6.1.4.1.6247.24.1.1.3.1	DisplayString	read-only	Unit returns the value of the internal software revision installed in the unit, in the form of: Boot: XXXXXX Bulk1: YYYYYY Bulk2: ZZZZZZ, where: XXXXXX = software version of boot YYYYYY = software version of bulk1 ZZZZZZ = software version of bulk2
INT cdm570ForceRedundentSwitch	1.3.6.1.4.1.6247.24.1.6.5.2	INTEGER	read-write	Force redundundent switch command.
cdm570Frame	1.3.6.1.4.1.6247.24.1.2.4
INT cdm570FramingMode	1.3.6.1.4.1.6247.24.1.2.4.1	INTEGER	read-write	Unit operating mode, where: 0 = Unframed 1 = EDMAC Framing 2 = EDMAC-2 Framing
cdm570G703T1	1.3.6.1.4.1.6247.24.1.2.5.3
cdm570Groups	1.3.6.1.4.1.6247.24.3.1
INT cdm570HigherOrderModulation	1.3.6.1.4.1.6247.24.1.1.2.4	INTEGER	read-only	Higer order modulation, where: 0 = None 1 = 8-PSK/8-QAM 2 = 16-QAM 3 = 8-PSK/8-QAM and 16-QAM
cdm570ID	1.3.6.1.4.1.6247.24.1.6.4
cdm570Interface	1.3.6.1.4.1.6247.24.1.2.5
cdm570InternalReference	1.3.6.1.4.1.6247.24.1.6.3
IP cdm570IpAddress	1.3.6.1.4.1.6247.24.1.2.1.1	IpAddress	read-write	The IP address for the 10/100 BaseTx Ethernet management port.
INT cdm570IPOption	1.3.6.1.4.1.6247.24.1.1.2.5	INTEGER	read-only	IP Controller card, where: 0 = None 1 = Installed
INT cdm570IpSubnetMask	1.3.6.1.4.1.6247.24.1.2.1.2	INTEGER	read-write	The network prefix length for the 10/100 BaseTx Ethernet management port.
MAC cdm570MacAddress	1.3.6.1.4.1.6247.24.1.2.1.4	MacAddress	read-only	The MAC address of the Ethernet interface.
INT cdm570ModelNumber	1.3.6.1.4.1.6247.24.1.1.2.2	INTEGER	read-only	Modem model number.
cdm570Monitor	1.3.6.1.4.1.6247.24.1.3
cdm570Notifications	1.3.6.1.4.1.6247.24.2
cdm570NotificationsGroup	1.3.6.1.4.1.6247.24.3.1.2			CDM-570 (Both L-Band and IF-Band) Notifications Group.
cdm570NotificationsPrefix	1.3.6.1.4.1.6247.24.2.0
cdm570Objects	1.3.6.1.4.1.6247.24.1
cdm570ObjectsGroup	1.3.6.1.4.1.6247.24.3.1.1			CDM-570 (Both L-Band and IF-Band) Objects Group.
cdm570ODU	1.3.6.1.4.1.6247.24.1.2.8
cdm570ODUComms	1.3.6.1.4.1.6247.24.1.6.6
INT cdm570ODUCommsEnabled	1.3.6.1.4.1.6247.24.1.6.6.1	INTEGER	read-write	ODU Comms, where 0 = Disabled 1 = Enabled
cdm570ODUParams	1.3.6.1.4.1.6247.24.1.3.6
cdm570RealTimeClock	1.3.6.1.4.1.6247.24.1.6.2
INT cdm570ReCenterBuffer	1.3.6.1.4.1.6247.24.1.6.1.1	INTEGER	read-write	Forces the software to recenter the receive Plesiochronous/Doppler buffer. This is a command only.
cdm570Redundancy	1.3.6.1.4.1.6247.24.1.6.5
INT cdm570RedundancyState	1.3.6.1.4.1.6247.24.1.6.5.1	INTEGER	read-only	Unit returns the redundancy state of the unit, where: 0 = Offline 1 = Online
cdm570Reference	1.3.6.1.4.1.6247.24.1.2.6
INT cdm570ReferenceFrequency	1.3.6.1.4.1.6247.24.1.2.6.1	INTEGER	read-write	External reference frequency, where: 0 = Internal 10 MHz 1 = External 1 MHz 2 = External 2 MHz 3 = External 5 MHz 4 = External 10 MHz 5 = External 20 MHz
INT cdm570RSCodecOption	1.3.6.1.4.1.6247.24.1.1.2.6	INTEGER	read-only	RS Codec Option, where: 0 = None 1 = Installed
STR cdm570RTCDate	1.3.6.1.4.1.6247.24.1.6.2.1	DisplayString	read-write	A date in the form dd/mm/yy, where dd = day of the month (01 to 31) mm = month (01 to 12) yy = year (00 to 99)
STR cdm570RTCTime	1.3.6.1.4.1.6247.24.1.6.2.2	DisplayString	read-write	A time in the form hh:mm:ss, indicating the time from midnight, where: hh = hours (00 to 23) mm = minutes (00 to 59) ss = seconds (00 to 59)
INT cdm570RTS	1.3.6.1.4.1.6247.24.1.2.5.2.1	INTEGER	read-write	Defines how RTS/CTS will operate at the main data interface, where: 0 = RTS/CTS Loop, No Action (RTS and CTS are looped, so that CTS echoes the state of RTS, but RTS does not control the ON/OFF state of the carrier) 1 = Loop, RTS controls Tx Ouput (RTS and CTS are looped, so that CTS echoes the state of RTS and RTS controls the ON/OFF state of the carrier - the modem will not bring up its TX carrier until RTS is asserted.) 2 = Ignore RTS, Assert CTS Query Only: 3 = 1:N system in use, RTS/CTS ignored
cdm570RTSCTSOper	1.3.6.1.4.1.6247.24.1.2.5.2
cdm570Rx	1.3.6.1.4.1.6247.24.1.2.3
INT cdm570RxAlarms	1.3.6.1.4.1.6247.24.1.3.1.3	INTEGER	read-only	Modem RX Traffic Faults Value Description of status parameter 0 Rx Traffic OK 1 Demodulator unlocked 3 AGC Alarm - signal out of range 5 RS Frame sync alarm 7 EDMAC Frame sync alarm 10 Buffer underflow 11 Buffer overflow 13 Eb/No alarm 15 AIS detected on incoming data
INT cdm570RxBERMultiplier	1.3.6.1.4.1.6247.24.1.3.2.1	INTEGER	read-only	Estimated corrected BER. The BER is calculated by mubliplying the Multiplier by 10E-10. Calculuation: RxBER = (Multiplier) * 0.0000000001 Returns 2147483647 (max int) if demod is unlocked.
INT cdm570RxBufferSize	1.3.6.1.4.1.6247.24.1.2.3.9	INTEGER	read-write	Rx buffer size, where: 0 = Buffer disabled (Clock mode = Rx satellite) 1 = +/- 1024 bits 2 = +/- 2048 bits 3 = +/- 4096 bits 4 = +/- 8192 bits 5 = +/- 16384 bits 6 = +/- 32786 bits 7 = +/- 128 bits 8 = +/- 256 bits 9 = +/- 512 bits
INT cdm570RxDataInvert	1.3.6.1.4.1.6247.24.1.2.3.8	INTEGER	read-write	Invert receive data, where: 0 = Normal 1 = Inverted
INT cdm570RxDataRate	1.3.6.1.4.1.6247.24.1.2.3.2	INTEGER	read-write	Rx data rate in bps (Varies based on chart below.) Units = bps Resolution = 1 bps FEC Type Modulation Code Rate Data Rate High Rate -------- ----------- ---------- --------------------- --------- None BPSK Uncoded 4.8 kbps to 3.0 Mbps None QPSK/OQPSK Uncoded 9.6 kbps to 5.0 Mbps Viterbi BPSK Rate 1/2 2.4 kbps to 1.5 Mbps Viterbi QPSK/OQPSK Rate 1/2 4.8 kbps to 3.0 Mbps Viterbi QPSK/OQPSK Rate 3/4 7.2 kbps to 4.5 Mbps Viterbi QPSK/OQPSK Rate 7/8 8.4 kbps to 5.0 Mbps Vit + RS BPSK Rate 1/2 2.4 kbps to 1.363 Mbps Vit + RS QPSK/OQPSK Rate 1/2 4.3 kbps to 2.727 Mbps Vit + RS QPSK/OQPSK Rate 3/4 6.5 kbps to 4.091 Mbps Vit + RS QPSK/OQPSK Rate 7/8 7.5 kbps to 4.666 Mbps Vit + RS 16-QAM Rate 3/4 13.0 kbps to 4.0 Mbps Vit + RS 16-QAM Rate 7/8 16.8 kbps to 4.666 Mbps TCM + RS 8-PSK Rate 2/3 8.7 kbps to 4.4 Mbps Turbo BPSK Rate 5/16 2.4 kbps to 0.937 Mbps Turbo BPSK Rate 21/44 2.4 kbps to 1.430 Mbps Turbo QPSK/OQPSK Rate 21/44 4.8 kbps to 2.860 Mbps Turbo QPSK/OQPSK Rate 3/4 7.2 kbps to 4.5 Mbps N/A Turbo QPSK/OQPSK Rate 7/8 8.4 kbps to 5.0 Mbps 5.25 Mbps Turbo QPSK/OQPSK Rate 0.95 9.1 kbps to 5.0 Mbps 5.667 Mbps Turbo 8-PSK/8-QAM Rate 3/4 10.8 kbps to 5.0 Mbps 6.75 Mbps Turbo 8-PSK/Q-QAM Rate 7/8 13.6 kbps to 5.0 Mbps 7.875 Mbps Turbo 8-PSK/Q-QAM Rate 0.95 15.3 kbps to 5.0 Mbps 8.5 Mbps Turbo 16-QAM Rate 3/4 14.4 kbps to 5.0 Mbps 9.0 Mbps Turbo 16-QAM Rate 7/8 16.8 kbps to 5.0 Mbps 9.98 Mbps
INT cdm570RxDemodAcqSweepWidth	1.3.6.1.4.1.6247.24.1.2.3.11	INTEGER	read-write	Rx +/- acquisition sweep range of demodulator, in KHz, ranging from: +/- 1 to +/- 32 KHz (rates = 625 ksym/second).
INT cdm570RxDemodType	1.3.6.1.4.1.6247.24.1.2.3.4	INTEGER	read-write	Rx demodulation type, where: 0 = BPSK 1 = QPSK 2 = OQPSK 3 = 8-PSK 4 = 16-QAM (Turbo or Viterbi + RS only) 5 = 8-QAM Depending on FEC type, not all of these selections will be valid.
INT cdm570RxDescrambler	1.3.6.1.4.1.6247.24.1.2.3.10	INTEGER	read-write	Rx descrambler state, where: 0 = Off 1 = On (default descrambler type) 2 = On - IESS-315 (Turbo only)
INT cdm570RxEbNo	1.3.6.1.4.1.6247.24.1.3.2.5	INTEGER	read-only	Unit returns the value of Eb/No, between 0 and 16 db. Units = 0.1 dB. Resolution 0.1 dB. Returns 999 if demod is unlocked. For values greater than 16 dB, the reply will be 160.
INT cdm570RxEbNoAlarmPoint	1.3.6.1.4.1.6247.24.1.2.3.6	INTEGER	read-write	Rx Eb/No alarm point in 0.1 dB, with a range between 0.1 dB and 16 dB. Units = 0.1 dB. Resolution = 0.1 dB.
INT cdm570RxFECCodeRate	1.3.6.1.4.1.6247.24.1.2.3.3	INTEGER	read-write	Rx code rate, where 0 = Rate 5/16 (Turbo only) 1 = Rate 22/44 (Turbo only) 2 = Rate 1/2 3 = Rate 2/3 (8-PSK TCM or 16-QAM only) 4 = Rate 3/4 5 = Rate 7/8 6 = Rate 0.95 (Turbo only) 7 = Rate 1/1 (Uncoded or No FEC)
INT cdm570RxFECType	1.3.6.1.4.1.6247.24.1.2.3.5	INTEGER	read-write	Rx FEC type where: 0 = Uncoded 1 = Viterbi 2 = Viterbit + Reed-Solomon 5 = TCM + Reed-Solomon (Code Rate = 2/3) 6 = Turbo 7 = TPC/LDPC Depending on hardware, not all of these selections will be valid.
INT cdm570RxFrequency	1.3.6.1.4.1.6247.24.1.2.3.1	INTEGER	read-write	Receive frequency for both CDM-570L (L-Band) modem and CDM-570 (IF-band) modems. L-Band is 950 MHz to 1950 MHz. IF-Band is 50 MHz to 90 MHz and 100 MHz to 180 MHz. Units = Hz. Resolution = 100 Hz.
INT cdm570RxFrequencyOffset	1.3.6.1.4.1.6247.24.1.3.2.3	INTEGER	read-only	Unit returns the value of the measured frequency offset of the carrier being demodulated in Hz. Units = Hz. Resolution 100 Hz. Range = -200,000 Hz to 0 Hz and 0 Hz to 200,000 Hz.
cdm570RxParams	1.3.6.1.4.1.6247.24.1.3.2
INT cdm570RxSignalLevel	1.3.6.1.4.1.6247.24.1.3.2.4	INTEGER	read-only	Unit returns the value of the Rx signal level, in dBm, between -99 dBm and -5 dBm. Returns -100 if signal is less than -99 dBm. Returns -4 if signal is greater than -5 dBm.
INT cdm570RxSpectrumInvert	1.3.6.1.4.1.6247.24.1.2.3.7	INTEGER	read-write	Rx spectrum inversion, where: 0 = Normal 1 = Rx spectrum inverted
INT cdm570RxSymbolRate	1.3.6.1.4.1.6247.24.1.2.3.12	INTEGER	read-only	Rx symbol rate in symbols per second (sps) Units = symbols per second (sps) Resolution = 1 sps
NTF cdm570RxTrafficAlarm	1.3.6.1.4.1.6247.24.2.0.3			Modem RX Traffic Faults Trap
cdm570SaveLoad	1.3.6.1.4.1.6247.24.1.5
STR cdm570SerialNumber	1.3.6.1.4.1.6247.24.1.1.1.1	DisplayString	read-only	Used to query the unit 9-digit serial number. Unit returns its S/N in the form xxxxxxxxx.
cdm570SNMP	1.3.6.1.4.1.6247.24.1.2.1.6
STR cdm570SNMPTrapCommunity	1.3.6.1.4.1.6247.24.1.2.1.6.3	DisplayString	read-write	The community that will be included in SNMP notifications (traps) that are sent from unit.
IP cdm570SNMPTrapDestinationIpAddress1	1.3.6.1.4.1.6247.24.1.2.1.6.1	IpAddress	read-write	The IP address were SNMP notifications (traps) are to be sent. This IP address should correspond to a SNMP manager or browser.
IP cdm570SNMPTrapDestinationIpAddress2	1.3.6.1.4.1.6247.24.1.2.1.6.2	IpAddress	read-write	The IP address were SNMP notifications (traps) are to be sent. This IP address should correspond to a SNMP manager or browser.
INT cdm570SNMPTrapVersion	1.3.6.1.4.1.6247.24.1.2.1.6.4	INTEGER	read-write	The SNMP version that will be used when sending traps from the unit. SNMPv1 will send V1 traps. SNMPv2 will send V2 notifications.
INT cdm570StatisticAvgEbNo	1.3.6.1.4.1.6247.24.1.3.4.2.1.5	INTEGER	read-only	Minimum Eb/No during sample period. Units = 0.1 dB. Returns 999 if demod was unlocked during sample period.
INT cdm570StatisticAvgTxPowerIncrease	1.3.6.1.4.1.6247.24.1.3.4.2.1.7	INTEGER	read-only	Average Tx power level increase during sample period. Units = 0.1 dB
STR cdm570StatisticDate	1.3.6.1.4.1.6247.24.1.3.4.2.1.2	DisplayString	read-only	The date of the statistic in the form ddmmyy, where: dd = day of the month (01 to 31) mm = month (01 to 12) yy = year (00 to 99)
INT cdm570StatisticIndex	1.3.6.1.4.1.6247.24.1.3.4.2.1.1	INTEGER	read-only	Index for stored statistics table.
INT cdm570StatisticMaxTxPowerIncrease	1.3.6.1.4.1.6247.24.1.3.4.2.1.6	INTEGER	read-only	Max. Tx power level increase during sample period. Units = 0.1 dB
INT cdm570StatisticMinEbNo	1.3.6.1.4.1.6247.24.1.3.4.2.1.4	INTEGER	read-only	Minimum Eb/No during sample period. Units = 0.1 dB. Returns 999 if demod was unlocked during sample period.
cdm570Statistics	1.3.6.1.4.1.6247.24.1.3.4
INT cdm570StatisticsSampleInterval	1.3.6.1.4.1.6247.24.1.3.4.1	INTEGER	read-write	Used to set the sample interval for the statistics logging function, where the enumerated lists goes from 0 to 9 in 10 minute steps. Setting 0 disables the statistics logging function.
STR cdm570StatisticTime	1.3.6.1.4.1.6247.24.1.3.4.2.1.3	DisplayString	read-only	The time of the statistic in the form hhmmss, indicating the time from midnight, where: hh = hours (00 to 23) mm = minutes (00 to 59) ss = seconds (00 to 59)
cdm570StoredEventsEntry	1.3.6.1.4.1.6247.24.1.3.3.1.1		not-accessible	The entry for the stored events table.
cdm570StoredEventsTable	1.3.6.1.4.1.6247.24.1.3.3.1		not-accessible	The table for stored events.
cdm570StoredStatisticsEntry	1.3.6.1.4.1.6247.24.1.3.4.2.1		not-accessible	Entry for stored statistics table.
cdm570StoredStatisticsTable	1.3.6.1.4.1.6247.24.1.3.4.2		not-accessible	Description.
cdm570System	1.3.6.1.4.1.6247.24.1.1
cdm570SystemEquipmentID	1.3.6.1.4.1.6247.24.1.1.2
cdm570SystemFirmware	1.3.6.1.4.1.6247.24.1.1.3
cdm570SystemInfo	1.3.6.1.4.1.6247.24.1.1.1
INT cdm570T1LineBuildOut	1.3.6.1.4.1.6247.24.1.2.5.3.1	INTEGER	read-write	Valid only for T1 interface, where: 0 = 0 - 133 feet 1 = 133 - 266 feet 2 = 266 - 399 feet 3 = 399 - 533 feet 4 = 533 - 655 feet
INT cdm570Temperature	1.3.6.1.4.1.6247.24.1.1.1.2	INTEGER	read-only	Unit returns the value of the internal temperature, in degrees Celsius.
cdm570Test	1.3.6.1.4.1.6247.24.1.4
INT cdm570TurboOption	1.3.6.1.4.1.6247.24.1.1.2.1	INTEGER	read-only	Turbo option, where: 0 = None 1 = Turbo 2 = TPC/LDPC
cdm570Tx	1.3.6.1.4.1.6247.24.1.2.2
INT cdm570TxAlarms	1.3.6.1.4.1.6247.24.1.3.1.2	INTEGER	read-only	Modem TX Traffic Faults: Value Description of Tx Traffic status 0 Tx traffic OK 1 No clock from terrestrial interface 3 Tx FIFO slip 5 Loss of External Reference 7 AUPC upper limit reached 9 AIS Detected on incoming data 11 Bipolar violation on G.705 interface
INT cdm570TxCarrierState	1.3.6.1.4.1.6247.24.1.2.2.11	INTEGER	read-write	Transmit carrier state, where: 0 = Off 1 = On 2 = RTI (Receive/Transmit Inhibit) The following values are query only: 3 = External Control (read only) 4 = BUC warm-up delay (read only) 5 = STDMA Burst (ready only)
INT cdm570TxClockSource	1.3.6.1.4.1.6247.24.1.2.2.8	INTEGER	read-write	Transmit clock source, where: 0 = Internal 1 = Tx Terrestrial 2 = Loop-Timed
INT cdm570TxDataInvert	1.3.6.1.4.1.6247.24.1.2.2.7	INTEGER	read-write	Invert transmit data, where: 0 = Normal 1 = Inverted
INT cdm570TxDataRate	1.3.6.1.4.1.6247.24.1.2.2.2	INTEGER	read-write	Tx data rate in bps (Varies based on chart below.) Units = bps Resolution = 1 bps FEC Type Modulation Code Rate Data Rate High Rate -------- ----------- ---------- --------------------- --------- None BPSK Uncoded 4.8 kbps to 3.0 Mbps None QPSK/OQPSK Uncoded 9.6 kbps to 5.0 Mbps Viterbi BPSK Rate 1/2 2.4 kbps to 1.5 Mbps Viterbi QPSK/OQPSK Rate 1/2 4.8 kbps to 3.0 Mbps Viterbi QPSK/OQPSK Rate 3/4 7.2 kbps to 4.5 Mbps Viterbi QPSK/OQPSK Rate 7/8 8.4 kbps to 5.0 Mbps Vit + RS BPSK Rate 1/2 2.4 kbps to 1.363 Mbps Vit + RS QPSK/OQPSK Rate 1/2 4.3 kbps to 2.727 Mbps Vit + RS QPSK/OQPSK Rate 3/4 6.5 kbps to 4.091 Mbps Vit + RS QPSK/OQPSK Rate 7/8 7.5 kbps to 4.666 Mbps Vit + RS 16-QAM Rate 3/4 13.0 kbps to 4.0 Mbps Vit + RS 16-QAM Rate 7/8 16.8 kbps to 4.666 Mbps TCM + RS 8-PSK Rate 2/3 8.7 kbps to 4.4 Mbps Turbo BPSK Rate 5/16 2.4 kbps to 0.937 Mbps Turbo BPSK Rate 21/44 2.4 kbps to 1.430 Mbps Turbo QPSK/OQPSK Rate 21/44 4.8 kbps to 2.860 Mbps Turbo QPSK/OQPSK Rate 3/4 7.2 kbps to 4.5 Mbps N/A Turbo QPSK/OQPSK Rate 7/8 8.4 kbps to 5.0 Mbps 5.25 Mbps Turbo QPSK/OQPSK Rate 0.95 9.1 kbps to 5.0 Mbps 5.667 Mbps Turbo 8-PSK/8-QAM Rate 3/4 10.8 kbps to 5.0 Mbps 6.75 Mbps Turbo 8-PSK/Q-QAM Rate 7/8 13.6 kbps to 5.0 Mbps 7.875 Mbps Turbo 8-PSK/Q-QAM Rate 0.95 15.3 kbps to 5.0 Mbps 8.5 Mbps Turbo 16-QAM Rate 3/4 14.4 kbps to 5.0 Mbps 9.0 Mbps Turbo 16-QAM Rate 7/8 16.8 kbps to 5.0 Mbps 9.98 Mbps
INT cdm570TxFECCodeRate	1.3.6.1.4.1.6247.24.1.2.2.3	INTEGER	read-write	Transmit code rate, where 0 = Rate 5/16 (Turbo only) 1 = Rate 22/44 (Turbo only) 2 = Rate 1/2 3 = Rate 2/3 (8-PSK TCM or 16-QAM only) 4 = Rate 3/4 5 = Rate 7/8 6 = Rate 0.95 (Turbo only) 7 = Rate 1/1 (Uncoded or No FEC)
INT cdm570TxFECType	1.3.6.1.4.1.6247.24.1.2.2.5	INTEGER	read-write	Transmit FEC type where: 0 = Uncoded 1 = Viterbi 2 = Viterbit + Reed-Solomon 5 = TCM + Reed-Solomon (Code Rate = 2/3) 6 = Turbo 7 = TPC/LDPC Depending on hardware, not all of these selections will be valid.
INT cdm570TxFrequency	1.3.6.1.4.1.6247.24.1.2.2.1	INTEGER	read-write	Transmit frequency for both CDM-570L (L-Band) modem and CDM-570 (IF-band) modems. L-Band is 950 MHz to 1950 MHz. IF-Band is 50 MHz to 90 MHz and 100 MHz to 180 MHz. Units = Hz. Resolution = 100 Hz.
INT cdm570TxModType	1.3.6.1.4.1.6247.24.1.2.2.4	INTEGER	read-write	Transmit modulation type, where: 0 = BPSK 1 = QPSK 2 = OQPSK 3 = 8-PSK 4 = 16-QAM (Turbo or Viterbi + RS only) 5 = 8-QAM Depending on FEC type, not all of these selections will be valid.
INT cdm570TxPowerLevel	1.3.6.1.4.1.6247.24.1.2.2.10	INTEGER	read-write	Transmit output power level for both CDM-570L (L-Band) modem and CDM-570 (IF-band) modem. CDM-570L power level is between -40 and 0 dBm. CDM-570 power level is between -25 and 0 dBm. Units = 0.1 dBm
INT cdm570TxScrambler	1.3.6.1.4.1.6247.24.1.2.2.9	INTEGER	read-write	Transmit scrambler state, where: 0 = Off 1 = On (Default scrambler type) 2 = On = IESS-315 (Turbo only)
INT cdm570TxSpectrumInvert	1.3.6.1.4.1.6247.24.1.2.2.6	INTEGER	read-write	Transmit spectrum invert selection, where: 0 = Normal 1 = Transmit spectrum inverted
INT cdm570TxSymbolRate	1.3.6.1.4.1.6247.24.1.2.2.12	INTEGER	read-only	Tx symbol rate in symbols per second (sps) Units = symbols per second (sps) Resolution = 1 sps
NTF cdm570TxTrafficAlarm	1.3.6.1.4.1.6247.24.2.0.2			Modem TX Traffic Faults Trap
NTF cdm570UnitAlarm	1.3.6.1.4.1.6247.24.2.0.1			Modem Unit Faults Trap
INT cdm570UnitAlarms	1.3.6.1.4.1.6247.24.1.3.1.1	INTEGER	read-only	Modem Unit Faults: Value Description of unit fault 0 No faults 1 +5 Volt power supply 2 +12 Volt power supply 3 -5 Volt power supply 4 +23 Volt power supply 5 -12 Volt power supply 6 Tx synthesizer lock 7 Rx 1st LO synthesize lock 8 Rx 2nd LO synthesize lock 9 Ref PLL lock 14 MPP50 (IP Module) Fault 15 EEPROM checksum error
INT cdm570UnitTestMode	1.3.6.1.4.1.6247.24.1.4.1	INTEGER	read-write	Unit Test Mode where: 0 = Normal Mode 1 = IF Loopback 2 = Digital Loopback 3 = IO Loopback 4 = RF Loopback 5 = Tx CW 6 = Tx Alternating Pattern
cdm570Util	1.3.6.1.4.1.6247.24.1.6
INT cdm570WarmUpCountdown	1.3.6.1.4.1.6247.24.1.6.3.3	INTEGER	read-write	As a query, returns the Warm-up delay countdown in seconds remaining. As a command, only takes the argument 0 and is used to truncate the warm-up delay period to zero, forcing the unit into 'instanct-on' mode.
INT cdm570WarmUpDelay	1.3.6.1.4.1.6247.24.1.6.3.2	INTEGER	read-write	Warm-up delay for internal frequency reference (OCXO), where: 0 = Disabled (instant on - no delay for OCXO to reach temperature) 1 = Enabled (unit waits until OCXO reaches correct temperature)

RFC description

Comtech CDM-570 L-Band and IF-Band satellite modem monitoring including temperature, system info, and turbo options.

Start monitoring Comtech EF Data satellite modems with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CDM-570

What Is CDM-570?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description