CDM-570L

All MIBs › CDM-570L

Organization: Comtech EF Data Corp.

Last Updated: 2006-02-22

Category: Satellite, Vendor: Comtech EF Data

Description: Manages Comtech EF Data CDM-570L low-power satellite modem configuration and RF link performance monitoring.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is CDM-570L?

CDM-570L is the MODULE-IDENTITY MIB for the Comtech EF Data CDM-570L satellite modem family (both L-Band and IF-Band variants), a low-power satellite communications modem used in VSAT and point-to-point satellite links. It defines the management identity/registration point for the modem's configuration and status objects, which in this product family typically cover RF/IF link parameters (transmit/receive frequency, modulation, FEC), demodulator lock/signal-quality status, and general unit configuration. As a satellite modem management MIB, it would be used to monitor the hardware and RF-link status of the modem: whether the demodulator has signal lock, receive signal level/Eb-No, and overall unit operational state, which are the key indicators of satellite link health. It typically works alongside a companion traps MIB (e.g., CDM-570Traps) for fault/alarm notifications rather than defining traps itself. It is deployed at remote and hub-site satellite ground stations for point-to-point or VSAT satellite data links. Engineers can download the CDM-570L file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in CDM-570L. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Comtech EF Data CDM-570L satellite modem

Monitoring Examples

No sample objects were provided for this module beyond its identity declaration, so specific leaf-object names cannot be confirmed; in practice, an operator monitoring a CDM-570L would poll demodulator lock and Eb/No objects to detect satellite link degradation from rain fade or antenna mispointing, and check the unit's configured frequency/modulation against expected values after a configuration change. Because no grounded sample objects were supplied, this is a generic rather than object-specific scenario.

What Can Be Monitored

demodulator lock status
receive signal level / Eb-No
transmit/receive frequency configuration
modulation and FEC settings
unit operational status

Imported Objects

From CDM-570

cdm570	MODULE-IDENTITY
cdm570AlarmMask	OBJECT-IDENTITY
cdm570Alarms	OBJECT-IDENTITY
cdm570Conformance	OBJECT-IDENTITY
cdm570ODU	OBJECT-IDENTITY
cdm570ODUParams	OBJECT-IDENTITY
cdm570SystemEquipmentID	OBJECT-IDENTITY

From ComtechEFData

comtechEFData

MODULE-IDENTITY

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE

OIDs

OID symbolic	OID numeric	Type	Access	Description
cdm570	1.3.6.1.4.1.6247.24			Module Identity for both CDM-570 L-Band and IF-Band Satellite Modems.
INT cdm570LBUCOption	1.3.6.1.4.1.6247.24.1.1.2.7	INTEGER	read-only	BUC option, where: 0 = None 1 = 100 watt 2 = 150 watt
INT cdm570LAlarmMaskBUC	1.3.6.1.4.1.6247.24.1.2.7.9	INTEGER	read-write	BUC alarm mask, where: 0 = Unmasked 1 = Masked
INT cdm570LAlarmMaskLNB	1.3.6.1.4.1.6247.24.1.2.7.10	INTEGER	read-write	LNB alarm mask, where: 0 = Unmasked 1 = Masked
cdm570LBUC	1.3.6.1.4.1.6247.24.1.2.8.1
INT cdm570LBUCDCPower	1.3.6.1.4.1.6247.24.1.2.8.1.1	INTEGER	read-write	BUC power control, where: 0 = Disable BUC DC Power 1 = Enable BUC DC Power
cdm570LBUCFSK	1.3.6.1.4.1.6247.24.1.2.8.1.2
INT cdm570LBUCComms	1.3.6.1.4.1.6247.24.1.2.8.1.2.1	INTEGER	read-write	Enables or disables communication, via the FSK link, with an externally connected Block Up Converted (BUC), where: 0 = Disabled 1 = Enabled
INT cdm570LBUCAddress	1.3.6.1.4.1.6247.24.1.2.8.1.2.2	INTEGER	read-write	Indicates the BUC address, between 1 and 15.
INT cdm570LBUCRFOutput	1.3.6.1.4.1.6247.24.1.2.8.1.2.3	INTEGER	read-write	Indicates BUC output enable, where: 0 = Off (output disabled) 1 = On (output enabled)
INT cdm570LBUC10MHzReference	1.3.6.1.4.1.6247.24.1.2.8.1.3	INTEGER	read-write	Enables or disables the 10 MHz frequency reference to the BUC, where: 0 = Disabled 1 = Enabled
cdm570LBUCAlarm	1.3.6.1.4.1.6247.24.1.2.8.1.4
INT cdm570LBUCHighCurrentLimit	1.3.6.1.4.1.6247.24.1.2.8.1.4.1	INTEGER	read-write	BUC high current limit, between 500 and 4000 mA.
INT cdm570LBUCLowCurrentLimit	1.3.6.1.4.1.6247.24.1.2.8.1.4.2	INTEGER	read-write	BUC low current limit, between 0 and 3000 mA. BUC low current limit must not exceed BUC high current limit.
cdm570LBUCLO	1.3.6.1.4.1.6247.24.1.2.8.1.5
INT cdm570LBUCLOFrequency	1.3.6.1.4.1.6247.24.1.2.8.1.5.1	INTEGER	read-write	BUC transmit LO frequency in the range of 3000 to 65000 MHz. Setting 0 disables this feature. Terminal Frequency = BUC_LO +/- Tx_Frequency (depending on LO mix).
INT cdm570LBUCLOMix	1.3.6.1.4.1.6247.24.1.2.8.1.5.2	INTEGER	read-write	BUC LO frequency mix, where: 0 = Low-side mix 1 = High-side mix
cdm570LLNB	1.3.6.1.4.1.6247.24.1.2.8.2
INT cdm570LLNBDCPower	1.3.6.1.4.1.6247.24.1.2.8.2.1	INTEGER	read-write	LNB power control, where: 0 = Off 1 = On, 13V LNB voltage 2 = On, 18V LNB voltage 3 = On, 24V LNB voltage
INT cdm570LLNB10MHzReference	1.3.6.1.4.1.6247.24.1.2.8.2.2	INTEGER	read-write	LNB 10MHz frequency reference, where: 0 = Disable LNB 10MHz reference 1 = Enable LNB 10MHz reference
cdm570LLNBAlarm	1.3.6.1.4.1.6247.24.1.2.8.2.3
INT cdm570LLNBHighCurrentLimit	1.3.6.1.4.1.6247.24.1.2.8.2.3.1	INTEGER	read-write	LNB upper alarm limit for current, between 50 and 600 mA.
INT cdm570LLNBLowCurrentLimit	1.3.6.1.4.1.6247.24.1.2.8.2.3.2	INTEGER	read-write	LNB lower alarm limit for current, between 10 and 400 mA.
cdm570LLNBLO	1.3.6.1.4.1.6247.24.1.2.8.2.4
INT cdm570LLNBLOFrequency	1.3.6.1.4.1.6247.24.1.2.8.2.4.1	INTEGER	read-write	LNB receieve LO frequency, in the range of 3000 to 65000 MHz. Setting a 0 disables the feature. Terminal Frequency = LNB_LO +/- Rx_Frequency (depending on High/Low Mix)
INT cdm570LLNBLOMix	1.3.6.1.4.1.6247.24.1.2.8.2.4.2	INTEGER	read-write	LO frequency mix, where: 0 = Low-side mix 1 = High-side mix
INT cdm570LODUAlarms	1.3.6.1.4.1.6247.24.1.3.1.4	INTEGER	read-only	ODU Faults Value Description of status parameter 0 No ODU faults 1 BUC PLL 3 BUC current 5 BUC voltage 7 LNB current 9 LNB voltage 11 BUC temperature 13 BUC checksum
cdm570LBUCParams	1.3.6.1.4.1.6247.24.1.3.6.1
INT cdm570LBUCCurrent	1.3.6.1.4.1.6247.24.1.3.6.1.1	INTEGER	read-only	Indicates the value of the BUC current, between 0 and 9999 mA. Units = mA.
INT cdm570LBUCVoltage	1.3.6.1.4.1.6247.24.1.3.6.1.2	INTEGER	read-only	Indicates the value ofthe BUC voltage, between 0 and 64 volts in 0.1 volts. Units = 0.1 volts.
INT cdm570LBUCTemperature	1.3.6.1.4.1.6247.24.1.3.6.1.3	INTEGER	read-only	Indicates the BUC temperature in degrees Celsius. If not available, response is -99. Note: This query is only valid when FSK and BUC power are turned On.
INT cdm570LBUCSoftwareVersion	1.3.6.1.4.1.6247.24.1.3.6.1.4	INTEGER	read-only	Indicates the BUC software version, between 1 and 15. If not available, response is 0.
INT cdm570LBUCPLLAlarm	1.3.6.1.4.1.6247.24.1.3.6.1.5	INTEGER	read-only	BUC PLL lock state, where: 0 = Locked 1 = Unlocked 9 = Unavailable
INT cdm570LBUCPowerLevel	1.3.6.1.4.1.6247.24.1.3.6.1.6	INTEGER	read-only	BUC output power level in 0.1 watts. Units = 0.1 watts. Returns 0 when FSK and BUC power are not enabled.
INT cdm570LBUCTerminalTxFrequency	1.3.6.1.4.1.6247.24.1.3.6.1.7	INTEGER	read-only	Terminal Tx Frequency = BUC_LO +/- Tx_Frequency (depending on LO mix) Units = 100 Hz Resolution = 100 Hz Returns 0 if BUC LO is zero.
cdm570LLNBParams	1.3.6.1.4.1.6247.24.1.3.6.2
INT cdm570LLNBCurrent	1.3.6.1.4.1.6247.24.1.3.6.2.1	INTEGER	read-only	Indicates the value of the LNB current, between 0 and 999 mA.
INT cdm570LLNBVoltage	1.3.6.1.4.1.6247.24.1.3.6.2.2	INTEGER	read-only	Indicates the value of the LNB voltage, between 0 and 30 volts. Units = 0.1 volts If not available, response is 0.
INT cdm570LLNBTerminalRxFrequency	1.3.6.1.4.1.6247.24.1.3.6.2.3	INTEGER	read-only	Terminal Rx frequency = LNB LO +/- Rx_Frequency (depending on LO mix) Units = 100 Hz Resolution = 100 Hz Returns 0 if LNB_LO is zero.
cdm570Notifications	1.3.6.1.4.1.6247.24.2
cdm570NotificationsPrefix	1.3.6.1.4.1.6247.24.2.0
NTF cdm570LODUAlarm	1.3.6.1.4.1.6247.24.2.0.4			CDM-570L BUC and LNB ODU Alarm Trap
cdm570LGroups	1.3.6.1.4.1.6247.24.3.3
cdm570LObjectsGroup	1.3.6.1.4.1.6247.24.3.3.1			CDM-570L Objects Group.
cdm570LNotificationsGroup	1.3.6.1.4.1.6247.24.3.3.2			CDM-570L Notifications Group.
cdm570LCompliances	1.3.6.1.4.1.6247.24.3.4
cdm570LCompliance	1.3.6.1.4.1.6247.24.3.4.1			CDM-570L Compliance.

RFC description

CDM-570 L-Band and IF-Band satellite modem management including BUC/LNB alarms.

Start monitoring Comtech EF Data satellite modems with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CDM-570L

What Is CDM-570L?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description