ALCATEL-IND1-BGP-MIB

All MIBs › ALCATEL-IND1-BGP-MIB

Organization: Alcatel-Lucent

Last Updated: 2008-09-14

Category: Routing Protocols, Vendor: Alcatel-Lucent

Description: Alcatel OmniSwitch BGP-4 routing protocol MIB for managing eBGP/iBGP sessions, peers, and route policies.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ALCATEL-IND1-BGP-MIB?

ALCATEL-IND1-BGP-MIB is an Alcatel-Lucent Enterprise proprietary MIB for the OmniSwitch "Birds Of Prey" product line, providing configuration management for global BGP-4 routing parameters such as router AS number, BGP process enable state, and related global routing settings. Although the provided source excerpt contains no specific object or table names, BGP configuration MIBs of this type typically expose peer/neighbor tables, session state, and route counts alongside global process controls. For status monitoring it would typically let an administrator confirm whether the BGP process is enabled and, via companion peer tables, whether expected eBGP/iBGP sessions are established, which is central to detecting a routing adjacency failure. It complements the standard BGP4-MIB (RFC 4273) with Alcatel-specific global configuration objects rather than replacing it. It is deployed on Alcatel-Lucent OmniSwitch routers/switches acting as BGP speakers in enterprise or data center core/edge networks. Engineers can download the ALCATEL-IND1-BGP-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in ALCATEL-IND1-BGP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Alcatel-Lucent OmniSwitch (Birds Of Prey product line)

Monitoring Examples

No object or table names were provided for this module, so specific OIDs cannot be cited; typically such a MIB would be used to confirm the BGP process global enable state and AS number configuration, with peer session state tracked via a companion peer table, but the concrete objects are not confirmed here.

What Can Be Monitored

global BGP process enable state
local AS number
BGP peer session state (via companion tables)
route redistribution configuration

Imported Objects

From ALCATEL-IND1-BASE

routingIND1Bgp

OBJECT-IDENTITY

From IPV6-TC

Ipv6Address

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Gauge32
IpAddress
MODULE-IDENTITY
OBJECT-IDENTITY
OBJECT-TYPE
TimeTicks
Unsigned32

From SNMPv2-TC

DisplayString
RowStatus

How to Use in IPNetwork Monitor

Example using alaBgpNumEstabExternalPeers OID:

Select an Alcatel-Lucent Enterprise OmniSwitch switch as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type alaBgpNumEstabExternalPeers into the Find box to locate it in the OID tree, then select it and click OK. The number of External Peers that are in ESTABLISHED state. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
IP alaBgpAggrAddr	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.3.1.1	IpAddress	read-only	Aggregate address.
STR alaBgpAggrCommunity	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.3.1.8	DisplayString	read-create	The value to set the COMMUNITY attribute when advertising this aggregate.
alaBgpAggrEntry	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.3.1		not-accessible	BGP Aggregation entry.
G32 alaBgpAggrLocalPref	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.3.1.7	Gauge32	read-create	This specifies the override default LOCAL PREF to be used when advertising this aggregate to internal peers. A value of 0 indicates not to override the default.
IP alaBgpAggrMask	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.3.1.2	IpAddress	read-only	Aggregate Mask.
G32 alaBgpAggrMetric	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.3.1.6	Gauge32	read-create	This specifies the MED to be used when advertising this aggregate to external peers. A value of 0 indicates not to send MED.
ROW alaBgpAggrRowStatus	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.3.1.9	RowStatus	read-create	Row status variable.
INT alaBgpAggrSet	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.3.1.4	INTEGER	read-create	If enabled aggregate all aspaths.
INT alaBgpAggrState	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.3.1.5	INTEGER	read-only	if active the aggregate is actively being advertised.
INT alaBgpAggrSummarize	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.3.1.3	INTEGER	read-create	If enabled only aggregate is advertised. Otherwise more specific routes are also advertised.
alaBgpAggrTable	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.3		not-accessible	BGP Aggregate configuration table.
INT alaBgpAsOriginInterval	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.37	INTEGER	read-write	The minimum interval in seconds between successive updates advertising the networks belonging to the local autonomous system.
INT alaBgpAspathCompare	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.36	INTEGER	read-write	Specifies whether to include aspath comparison in route selection.
INT alaBgpAspathMatchListAction	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.2.1.4	INTEGER	read-write	This determines whether to accept or reject a matching route.
alaBgpAspathMatchListEntry	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.2.1		not-accessible	Aspath matching entry .
STR alaBgpAspathMatchListId	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.2.1.1	DisplayString	read-only	Identifier of this list of autonomous system path matching criteria.
INT alaBgpAspathMatchListPriority	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.2.1.3	INTEGER	read-write	This determines the order in which the matching regular expressions are applied in the list identified by alaBgpAspathMatchListId.
STR alaBgpAspathMatchListRegExp	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.2.1.2	DisplayString	read-only	The regular expression identifying the autnomous system paths to be matched by this instance.
ROW alaBgpAspathMatchListRowStatus	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.2.1.5	RowStatus	read-write	Row status variable
INT alaBgpAspathMatchListSubIndex	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.2.1.6	INTEGER	read-only	The primary index of this list.
alaBgpAspathMatchListTable	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.2		not-accessible	BGP Policy Aspath criteria matching table.
INT alaBgpAspathPriMatchListAction	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.5.1.5	INTEGER	read-only	This determines whether to accept or reject a matching route.
alaBgpAspathPriMatchListEntry	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.5.1		not-accessible	Aspath matching entry .
STR alaBgpAspathPriMatchListId	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.5.1.1	DisplayString	read-only	Identifier of this list of autonomous system path matching criteria.
INT alaBgpAspathPriMatchListIntIdx	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.5.1.3	INTEGER	read-only	This is the order in which the matching regular expressions are created in the list identified by alaBgpAspathPriMatchListId.
INT alaBgpAspathPriMatchListPriority	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.5.1.2	INTEGER	read-only	This determines the order in which the matching regular expressions are applied in the list identified by alaBgpAspathPriMatchListId.
STR alaBgpAspathPriMatchListRegExp	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.5.1.4	DisplayString	read-only	The regular expression identifying the autnomous system paths to be matched by this instance
ROW alaBgpAspathPriMatchListRowStatus	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.5.1.6	RowStatus	read-only	Row status variable.
alaBgpAspathPriMatchListTable	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.5		not-accessible	Priority sorted view of BGP Policy Aspath matching table.
INT alaBgpAutonomousSystemNumber	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.2	INTEGER	read-write	Autonomous System Number.
INT alaBgpBfdAllNeighborStatus	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.45	INTEGER	read-write	Enables/Disables BFd for all BGP Neighbors.
INT alaBgpBfdStatus	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.44	INTEGER	read-write	Enables/Disables BFd for BGP protocol.
IP alaBgpClusterId	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.31	IpAddress	read-write	The local cluster id of this route reflection cluster.
INT alaBgpCommunityMatchListAction	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.4.1.5	INTEGER	read-write	This determines whether to accept or reject a matching route.
alaBgpCommunityMatchListEntry	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.4.1		not-accessible	Community matching entry .
STR alaBgpCommunityMatchListId	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.4.1.1	DisplayString	read-only	Identifier of this list of communities matching criteria.
INT alaBgpCommunityMatchListPriority	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.4.1.3	INTEGER	read-write	This determines the order in which the matching regular expressions are applied in the list identified by alaBgpCommunityMatchListId.
ROW alaBgpCommunityMatchListRowStatus	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.4.1.6	RowStatus	read-write	Row status variable.
STR alaBgpCommunityMatchListString	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.4.1.2	DisplayString	read-only	The string identifying the communities to be matched by this instance.
INT alaBgpCommunityMatchListSubIndex	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.4.1.7	INTEGER	read-only	The primary index of this list.
alaBgpCommunityMatchListTable	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.4		not-accessible	BGP Policy Community criteria matching table.
INT alaBgpCommunityMatchListType	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.4.1.4	INTEGER	read-write	This determines the matching type.
INT alaBgpCommunityPriMatchListAction	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.6.1.6	INTEGER	read-only	This determines whether to accept or reject a matching route.
alaBgpCommunityPriMatchListEntry	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.6.1		not-accessible	Community matching entry .
STR alaBgpCommunityPriMatchListId	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.6.1.1	DisplayString	read-only	Identifier of this list of communities matching criteria.
INT alaBgpCommunityPriMatchListIntIdx	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.6.1.3	INTEGER	read-only	This determines the order in which the matching regular expressions are created in the list identified by alaBgpCommunityPriMatchListId.
INT alaBgpCommunityPriMatchListPriority	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.6.1.2	INTEGER	read-only	This determines the order in which the matching regular expressions are applied in the list identified by alaBgpCommunityPriMatchListId.
ROW alaBgpCommunityPriMatchListRowStatus	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.6.1.7	RowStatus	read-only	Row status variable
STR alaBgpCommunityPriMatchListString	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.6.1.4	DisplayString	read-only	The string identifying the communities to be matched by this instance.
alaBgpCommunityPriMatchListTable	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.6		not-accessible	Priority sorted view of BGP Policy Community matching table.
INT alaBgpCommunityPriMatchListType	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.6.1.5	INTEGER	read-only	This determines the matching type.
INT alaBgpConfedId	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.10	INTEGER	read-write	Confederation identifier. A value of 0 means this local speaker is not a member of any confederation
IP alaBgpDampAddr	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.7.1.1	IpAddress	read-only	Destination address.
INT alaBgpDampCeil	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.35	INTEGER	read-only	The maximum value that the figure of merit of a route can attain. This is a floating point value with 2 digit precision. For example, a value of 3.5 is encoded as 350, a value of 0.9 is encoded as 90, a value of 9.45 is encoded as 945.
INT alaBgpDampClear	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.7.1.9	INTEGER	read-write	A value of clear will clear this damp history information.
INT alaBgpDampCutOff	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.33	INTEGER	read-write	When a route's figure of merit reaches this value, the route is considered damped. This is a floating point value with 2 digit precision. For example, a value of 3.5 is encoded as 350, a value of 0.9 is encoded as 90 ,a value of 9.45 is encoded as 945.
TIK alaBgpDampDuration	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.7.1.6	TimeTicks	read-only	Time in seconds since the flap was noticed.
INT alaBgpDampening	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.11	INTEGER	read-write	Enable/Disable BGP route dampening
INT alaBgpDampeningClear	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.32	INTEGER	read-write	Writing a value of clear into this variable will clear the dampening history.
alaBgpDampEntry	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.7.1		not-accessible	BGP Network entry.
INT alaBgpDampFigureOfMerit	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.7.1.4	INTEGER	read-only	The figure of merit value. This is a floating point value with 2 digit precision. For example, a value of 3.5 is encoded as 350, a value of 0.9 is encoded as 90, a value of 9.45 is encoded as 945.
C32 alaBgpDampFlaps	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.7.1.5	Counter32	read-only	The number of times this route has flapped.
INT alaBgpDampHalfLife	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.38	INTEGER	read-write	The time in seconds in which the penalty to a flapping route decreases to half its initial value.
INT alaBgpDampHalfLifeReach	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.12	INTEGER	not-accessible	The time in seconds in which the penalty to a flapping route decreases to half its initial value while the route remains reachable. Obsoleted by the variable alaBgpDampHalfLife.
INT alaBgpDampHalfLifeUnReach	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.13	INTEGER	not-accessible	The time in seconds in which the penalty to a flapping route decreases to half its initial value while the route remains unreachable. Obsoleted by the variable alaBgpDampHalfLife.
TIK alaBgpDampLastUpdateTime	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.7.1.7	TimeTicks	read-only	Time in seconds since this damp entry (figure of merit) was last updated.
IP alaBgpDampMask	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.7.1.2	IpAddress	read-only	Destination mask.
INT alaBgpDampMaxFlapHistory	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.14	INTEGER	read-write	The time in seconds the flap history of a route is retained.
IP alaBgpDampPeerAddr	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.7.1.3	IpAddress	read-only	Neighbour address.
INT alaBgpDampReuse	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.34	INTEGER	read-write	When a route's figure of merit decays to this value, the route can be reused. This is a floating point value with 2 digit precision. For example, a value of 3.5 is encoded as 350, a value of 0.9 is encoded as 90 , a value of 9.45 is encoded as 945.
TIK alaBgpDampReuseTime	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.7.1.8	TimeTicks	read-only	Time in seconds until this route will be reused.
alaBgpDampTable	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.7		not-accessible	BGP Dampened paths table.
STR alaBgpDebugDescription	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.10.1.3	DisplayString	read-only	All the Debug Events/types described here stands deprecated in favour of MIB objects defined in alaDrcTmBgpDebug Configuration.
alaBgpDebugEntry	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.10.1		not-accessible	BGP debugging entry - has been deprecated in favour of alaDrcTmBgpDebug Configuration.
INT alaBgpDebugEvent	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.10.1.1	INTEGER	read-only	All the Debug Events/types described here stands deprecated in favour of MIB objects defined in alaDrcTmBgpDebug Configuration.
INT alaBgpDebugLevel	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.15	INTEGER	read-write	This object has been deprecated in favour of alaDrcTmBgpDebug Configuration.
INT alaBgpDebugStatus	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.10.1.2	INTEGER	read-write	All the Debug Events/types described here stands deprecated in favour of MIB objects defined in alaDrcTmBgpDebug Configuration.
alaBgpDebugTable	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.10		not-accessible	BGP debugging table - has been deprecated in favour of alaDrcTmBgpDebug Configuration.
G32 alaBgpDefaultLocalPref	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.6	Gauge32	read-write	The default LOCAL_PREF to be applied to routes learnt from neighbouring autonomous system.
INT alaBgpFastExternalFailOver	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.16	INTEGER	read-write	Enable/Disable Resetting session immediately if a link to a directly connected external peer is operationally down.
alaBgpGlobal	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1
INT alaBgpGracefulRestart	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.39	INTEGER	read-write	Enables BGP graceful restart capability.
INT alaBgpIgpSynchStatus	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.4	INTEGER	read-write	Enable/Disable BGP IGP Synchronization.
G32 alaBgpManualTag	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.8	Gauge32	read-only	Manual tag to be used. A value of 0 means no manual tagging.
INT alaBgpMaxPeers	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.20	INTEGER	read-only	Maximum BGP peers supported.
INT alaBgpMedAlways	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.5	INTEGER	read-write	Enable/Disable BGP Metric MULTI_EXIT_DISC comparison between routes from different Autonomous Systems.
alabgpMIBAggrGroup	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.2.1.3			A collection of objects for managing BGP aggregates.
alabgpMIBAspathListGroup	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.2.1.9			A collection of objects for managing BGP aspath lists.
alabgpMIBAspathPriListGroup	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.2.1.12			A collection of objects for managing BGP aspath lists by priority.
alabgpMIBCommunityListGroup	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.2.1.11			A collection of objects for managing BGP community lists.
alabgpMIBCommunityPriListGroup	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.2.1.13			A collection of objects for managing BGP community lists by priority.
alabgpMIBDampGroup	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.2.1.7			A collection of objects for managing BGP dampening.
alabgpMIBDebugGroup	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.2.1.15			A collection of objects for managing BGP debug infos. These objects have been deprecated, and this group is no longer mandatory.
alabgpMIBGlobalsGroup	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.2.1.1			A collection of objects providing information on global BGP state.
alabgpMIBNetwork6Group	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.2.1.16			A collection of objects for managing BGP IPv6 networks.
alabgpMIBNetworkGroup	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.2.1.4			A collection of objects for managing BGP networks.
alabgpMIBPath6AttrGroup	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.2.1.18			A collection of objects for managing BGP paths attributes.
alabgpMIBPathAttrGroup	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.2.1.6			A collection of objects for managing BGP paths attributes.
alabgpMIBPeer6Group	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.2.1.19			A collection of objects for managing BGP peers.
alabgpMIBPeerGroup	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.2.1.2			A collection of objects for managing BGP peers.
alabgpMIBPrefixListGroup	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.2.1.10			A collection of objects for managing BGP prefix lists.
alabgpMIBRedistRouteGroup	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.2.1.14			A collection of objects for managing BGP redistribution routes. These objects have been deprecated, and this group is no longer mandatory.
alabgpMIBRoute6Group	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.2.1.17			A collection of objects for managing BGP routes.
alabgpMIBRouteGroup	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.2.1.5			A collection of objects for managing BGP routes.
alabgpMIBRouteMapGroup	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.2.1.8			A collection of objects for managing BGP route maps.
INT alaBgpMissingMed	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.7	INTEGER	read-write	Specifies how to a missing med in a path attribute.
INT alaBgpMultiPath	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.29	INTEGER	read-write	Enable/Disable Equal-Cost MultiPaths
INT alaBgpMultiProtocolIpv4	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.42	INTEGER	read-write	Indicates whether IPv4 BGP4 capability is enabled.
INT alaBgpMultiProtocolIpv6	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.43	INTEGER	read-write	Indicates whether IPv6 BGP4 capability is enabled.
ADR alaBgpNetwork6Addr	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.11.1.1	Ipv6Address	read-write	The IPv6 address of the BGP Network.
STR alaBgpNetwork6Community	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.11.1.6	DisplayString	read-write	The value to set the COMMUNITY attribute when advertising this network.
alaBgpNetwork6Entry	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.11.1		not-accessible	BGP Network6 entry.
G32 alaBgpNetwork6LocalPref	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.11.1.5	Gauge32	read-write	This specifies the override default LOCAL PREF to be used when advertising this network to internal peers. A value of 0 indicates not to override the default.
U32 alaBgpNetwork6MaskLen	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.11.1.2	Unsigned32	read-write	The number of bits that are significant in the IPv6 address prefix of the BGP Network.
G32 alaBgpNetwork6Metric	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.11.1.4	Gauge32	read-write	This specifies the MED to be used when advertising this network to external peers. A value of 0 indicates not to send MED.
ROW alaBgpNetwork6RowStatus	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.11.1.7	RowStatus	read-write	Row status variable.
INT alaBgpNetwork6State	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.11.1.3	INTEGER	read-only	Indicates whether the network is being actively advertised or not.
alaBgpNetwork6Table	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.11		not-accessible	BGP Network6 configuration table.
IP alaBgpNetworkAddr	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.4.1.1	IpAddress	read-only	Aggregate address.
STR alaBgpNetworkCommunity	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.4.1.6	DisplayString	read-create	The value to set the COMMUNITY attribute when advertising this network.
alaBgpNetworkEntry	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.4.1		not-accessible	BGP Network entry.
G32 alaBgpNetworkLocalPref	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.4.1.5	Gauge32	read-create	This specifies the override default LOCAL PREF to be used when advertising this network to internal peers. A value of 0 indicates not to override the default.
IP alaBgpNetworkMask	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.4.1.2	IpAddress	read-only	Aggregate Mask.
G32 alaBgpNetworkMetric	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.4.1.4	Gauge32	read-create	This specifies the MED to be used when advertising this network to external peers. A value of 0 indicates not to send MED.
ROW alaBgpNetworkRowStatus	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.4.1.7	RowStatus	read-create	Row status variable.
INT alaBgpNetworkState	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.4.1.3	INTEGER	read-only	Indicates whether the network is being actively advertised or not.
alaBgpNetworkTable	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.4		not-accessible	BGP Network configuration table.
G32 alaBgpNumActiveRoutes	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.21	Gauge32	read-only	The number of active known routes in the BGP routing table
C32 alaBgpNumDampenedPaths	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.26	Counter32	read-only	The total number of dampened paths known to the system.
C32 alaBgpNumEstabExternalPeersEx	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.22	Counter32	read-only	The number of External Peers that are in ESTABLISHED state.
C32 alaBgpNumEstabInternalPeers	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.23	Counter32	read-only	The number of Internal Peers that are in ESTABLISHED state.
C32 alaBgpNumFeasiblePaths	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.25	Counter32	read-only	The total number of feasible paths known to the system.
C32 alaBgpNumIgpSyncWaitPaths	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.27	Counter32	read-only	The total number of paths learnt from internal peers that are waiting to be synchronized with IGP.
C32 alaBgpNumPaths	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.24	Counter32	read-only	The total number of paths known to the system.
C32 alaBgpNumPolicyChgPaths	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.28	Counter32	read-only	The total number of paths that are currently rejected but stored anticipating an inbound policy change for an external peer which is configured to accept dynamic policy changes.
ADR alaBgpPath6Addr	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.13.1.1	Ipv6Address	read-only	Destination address.
IP alaBgpPath6AggregatorAddr	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.13.1.15	IpAddress	read-only	The IP address of the last BGP4 speaker that performed route aggregation. A value of 0.0.0.0 indicates the absence of this attribute.
INT alaBgpPath6AggregatorAs	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.13.1.14	INTEGER	read-only	The AS number of the last BGP4 speaker that performed route aggregation. A value of 0 indicates the absence of this attribute.
STR alaBgpPath6As	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.13.1.10	DisplayString	read-only	The sequence of AS path segments. Each AS path segment is represented by a triple . The TYPE is a 1-octet field which has two possible values: (1) AS_SET : unordered set of ASs a route in the UPDATE message has traversed. (2) AS_SEQUENCE : ordered set of ASs a route in the UPDATE message has traversed. The LENGTH is a 1-octet field containing the number of ASs in the value field. The VALUE field contains one or more AS numbers, each AS is represented in the octet string as a pair of octets according to the following algorithm: first-byte-of-pair = ASNumber / 256; second-byte-of-pair = ASNumber & 255;
INT alaBgpPath6Atomic	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.13.1.13	INTEGER	read-only	Indicates whether this path is generated without selecting a less specific route.
STR alaBgpPath6ClusterList	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.13.1.19	DisplayString	read-only	Sequence of Cluster Id values representing the reflection path that the route has passed, if this is a reflected route in the local AS. Size of zero (0) indicates the absence of this attribute. Refer RFC 2796 (BGP Route Reflection), Section 7
STR alaBgpPath6Community	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.13.1.16	DisplayString	read-only	The community attribute of the path. The communities are represented as series of 4 octet values.
alaBgpPath6Entry	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.13.1		not-accessible	BGP path6 entry.
INT alaBgpPath6LocalPref	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.13.1.11	INTEGER	read-only	The LOCAL_PREF attribute of the path. A value of -1 indicates the absence of this attribute.
U32 alaBgpPath6MaskLen	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.13.1.2	Unsigned32	read-only	Destination address length.
G32 alaBgpPath6Med	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.13.1.12	Gauge32	read-only	The Multi Exit Disc. attribute of the path. A value of 4294967295 indicates the absence of this attribute.
ADR alaBgpPath6NextHop	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.13.1.9	Ipv6Address	read-only	The NEXTHOP attribute of the path.
INT alaBgpPath6Origin	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.13.1.8	INTEGER	read-only	The ORIGIN attribute of the path.
IP alaBgpPath6OriginatorId	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.13.1.18	IpAddress	read-only	The Router Id of the BGP4 speaker that performed route reflection, if this is a reflected route in the local AS. A value of 0.0.0.0 indicates the absence of this attribute. Refer RFC 2796 (BGP Route Reflection), Section 7
IP alaBgpPath6PeerBgpId	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.13.1.3	IpAddress	read-only	The BGP Identifier of the peer who sent this path. For locally sourced routes, the value is 0.0.0.0.
STR alaBgpPath6PeerName	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.13.1.20	DisplayString	read-only	The symbolic name of the peer that sent this path. For paths corresponding to local or redistributed routes on this router, the value is set to 'none'.
G32 alaBgpPath6Pref	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.13.1.6	Gauge32	read-only	The degree of preference assigned to this path.
INT alaBgpPath6SrcProto	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.13.1.4	INTEGER	read-only	The protocol from which the path was learnt.
INT alaBgpPath6State	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.13.1.7	INTEGER	read-only	Indicates the state of the path. When path state is none it indicates that there are no paths to this prefix/len and the route is being purged from the system. Stale indicates that the peer that advertised this route's nexthop is in the process of graceful restart.
alaBgpPath6Table	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.13		not-accessible	BGP Path table.
OCT alaBgpPath6UnknownAttr	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.13.1.17	OCTET STRING	read-only	One or more path attributes not understood by this BGP4 speaker. Size of zero (0) indicates the absence of such attribute(s). Octets beyond the maximum size, if any, are not recorded by this object.
INT alaBgpPath6Weight	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.13.1.5	INTEGER	read-only	The weight assigned to this path.
IP alaBgpPathAddr	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.6.1.1	IpAddress	read-only	Destination address.
IP alaBgpPathAggregatorAddr	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.6.1.15	IpAddress	read-only	The IP address of the last BGP4 speaker that performed route aggregation. A value of 0.0.0.0 indicates the absence of this attribute.
INT alaBgpPathAggregatorAs	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.6.1.14	INTEGER	read-only	The AS number of the last BGP4 speaker that performed route aggregation. A value of 0 indicates the absence of this attribute.
STR alaBgpPathAs	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.6.1.10	DisplayString	read-only	The sequence of AS path segments. Each AS path segment is represented by a triple . The TYPE is a 1-octet field which has two possible values: (1) AS_SET : unordered set of ASs a route in the UPDATE message has traversed. (2) AS_SEQUENCE : ordered set of ASs a route in the UPDATE message has traversed. The LENGTH is a 1-octet field containing the number of ASs in the value field. The VALUE field contains one or more AS numbers, each AS is represented in the octet string as a pair of octets according to the following algorithm: first-byte-of-pair = ASNumber / 256; second-byte-of-pair = ASNumber & 255;.
INT alaBgpPathAtomic	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.6.1.13	INTEGER	read-only	Indicates whether this path is generated without selecting a less specific route.
STR alaBgpPathClusterList	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.6.1.19	DisplayString	read-only	Sequence of Cluster Id values representing the reflection path that the route has passed, if this is a reflected route in the local AS. Size of zero (0) indicates the absence of this attribute. Refer RFC 2796 (BGP Route Reflection), Section 7
STR alaBgpPathCommunity	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.6.1.16	DisplayString	read-only	The community attribute of the path. The communities are represented as series of 4 octet values.
alaBgpPathEntry	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.6.1		not-accessible	BGP path entry.
INT alaBgpPathLocalPref	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.6.1.11	INTEGER	read-only	The LOCAL_PREF attribute of the path. A value of -1 indicates the absence of this attribute.
IP alaBgpPathMask	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.6.1.2	IpAddress	read-only	Destination Mask.
G32 alaBgpPathMed	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.6.1.12	Gauge32	read-only	The Multi Exit Disc. attribute of the path. A value of 4294967295 indicates the absence of this attribute.
IP alaBgpPathNextHop	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.6.1.9	IpAddress	read-only	The NEXTHOP attribute of the path.
INT alaBgpPathOrigin	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.6.1.8	INTEGER	read-only	The ORIGIN attribute of the path.
IP alaBgpPathOriginatorId	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.6.1.18	IpAddress	read-only	The Router Id of the BGP4 speaker that performed route reflection, if this is a reflected route in the local AS. A value of 0.0.0.0 indicates the absence of this attribute. Refer RFC 2796 (BGP Route Reflection), Section 7
IP alaBgpPathPeerAddr	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.6.1.3	IpAddress	read-only	The IP address or the BGP Identifier of the peer who sent this path. For locally sourced routes, the value is 0.0.0.0. For peers with an IPv4 address, the value will be the peer's IPv4 address, and the value of alaBgpPathPeerInetType will be ipv4. For peers with an IPv6 address, the value will be the peer's BGP Identifier, and the value of alaBgpPathPeerInetType will be ipv6.
INT alaBgpPathPeerInetType	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.6.1.20	INTEGER	read-only	Indicates whether the peer who sent this path has an IPv4 address or an IPv6 address. If set to ipv4, the peer has an IPv4 address, and the value of alaBgpPathPeerAddr is the peer's IPv4 address. If set to ipv6, the peer has an IPv6 address, and the value of alaBgpPathPeerAddr is the peer's BGP Identifier. For locally sourced routes, the value is set to unknown.
STR alaBgpPathPeerName	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.6.1.21	DisplayString	read-only	The symbolic name of the peer that sent this path. For paths corresponding to local or redistributed routes on this router, the value is set to 'none'.
G32 alaBgpPathPref	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.6.1.6	Gauge32	read-only	The degree of preference assigned to this path.
INT alaBgpPathSrcProto	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.6.1.4	INTEGER	read-only	The protocol from which the path was learnt.
INT alaBgpPathState	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.6.1.7	INTEGER	read-only	Indicates the state of the path. When path state is none it indicates that there are no paths to this prefix/len and the route is being purged from the system. Stale indicates that the peer that advertised this route's nexthop is in the process of graceful restart.
alaBgpPathTable	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.6		not-accessible	BGP Path table.
OCT alaBgpPathUnknownAttr	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.6.1.17	OCTET STRING	read-only	One or more path attributes not understood by this BGP4 speaker. Size of zero (0) indicates the absence of such attribute(s). Octets beyond the maximum size, if any, are not recorded by this object.
INT alaBgpPathWeight	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.6.1.5	INTEGER	read-only	The weight assigned to this path.
INT alaBgpPeer6ActivateIpv6	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.72	INTEGER	read-write	If enabled, the Multiprotocol IPv6 Unicast capability is advertised to this peer. If disabled, the capability is not advertised in the OPEN message.
ADR alaBgpPeer6Addr	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.1	Ipv6Address	read-only	Ipv6 Address of the peer.
INT alaBgpPeer6AdminStatus	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.68	INTEGER	read-write	The desired state of the BGP connection. A transition from 'stop' to 'start' will cause the BGP Start Event to be generated. A transition from 'start' to 'stop' will cause the BGP Stop Event to be generated. This parameter can be used to restart BGP peer connections. Care should be used in providing write access to this object without adequate authentication.
INT alaBgpPeer6AS	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.2	INTEGER	read-write	Autonomous system of the peer.
STR alaBgpPeer6AspathListIn	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.35	DisplayString	read-write	The name of the aspath-list to be applied to the updates received from this peer. This is same as alaBgpAspathMatchListId.
STR alaBgpPeer6AspathListOut	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.34	DisplayString	read-write	The name of the aspath-list to be applied to the updates sent to this peer. This is same as alaBgpAspathMatchListId.
INT alaBgpPeer6AutoReStart	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.29	INTEGER	read-write	Enable/Disable the peer autostart status. If enabled, the peer will be automatically restarted (if administratively enabled) after the transition to IDLE state.
IP alaBgpPeer6BgpId	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.55	IpAddress	read-only	BGP Identifier of the peer.
INT alaBgpPeer6ClearCounter	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.28	INTEGER	read-write	Setting a value of clear into this variable will clear the per peer statistics.
INT alaBgpPeer6ClientStatus	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.30	INTEGER	read-write	If enabled this peer is a route reflection client.
STR alaBgpPeer6CommunityListIn	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.39	DisplayString	read-write	The name of the community-list to be applied to the updates received from this peer. This is same as alaBgpCommunityMatchListId.
STR alaBgpPeer6CommunityListOut	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.38	DisplayString	read-write	The name of the community-list to be applied to the updates sent to this peer. This is same as alaBgpCommunityMatchListId.
INT alaBgpPeer6ConfedStatus	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.31	INTEGER	read-write	If enabled this peer is a member of our confederation.
INT alaBgpPeer6ConnRetryInterval	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.63	INTEGER	read-write	Time interval in seconds for the ConnectRetry timer. The suggested value for this timer is 120 seconds.
INT alaBgpPeer6DefaultOriginate	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.41	INTEGER	read-write	If enabled a default route is sent to this neighbour.
C32 alaBgpPeer6DownTransitions	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.26	Counter32	read-only	The Number of times this peer session transitioned to IDLE state.
alaBgpPeer6Entry	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1		not-accessible	BGP IPv6 Peer configuration entry.
INT alaBgpPeer6HoldTime	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.61	INTEGER	read-only	Time interval in seconds for the Hold Timer established with the peer. The value of this object is calculated by this BGP speaker by using the smaller of the value in alaBgpPeer6HoldTimeConfigured and the Hold Time received in the OPEN message. This value must be at lease three seconds if it is not zero (0) in which case the session has not been established with the peer, or, the value of alaBgpPeer6HoldTimeConfigured is zero (0).
INT alaBgpPeer6HoldTimeConfigured	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.64	INTEGER	read-write	Time interval in seconds for the Hold Time configured for this BGP speaker with this peer. This value is placed in an OPEN message sent to this peer by this BGP speaker, and is compared with the Hold Time field in an OPEN message received from the peer when determining the Hold Time (alaBgpPeer6HoldTime) with the peer. This value must not be less than three seconds if it is not zero (0) in which case the Hold Time is NOT to be negotiated with the peer. The suggested value for this timer is 90 seconds.
INT alaBgpPeer6InSoftReset	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.10	INTEGER	read-only	Route refresh capability is Enabled/Disabled on the connection to this peer.
INT alaBgpPeer6Ipv4Multicast	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.12	INTEGER	read-only	Multiprotocol capability IPv4 Multicast is Enabled/Disabled on the connection to this peer .
IP alaBgpPeer6Ipv4NextHop	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.66	IpAddress	read-write	The IPv4 nexthop address to be used for IPv4 routes advertised to this peer.
INT alaBgpPeer6Ipv4Unicast	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.11	INTEGER	read-only	Multiprotocol capability IPv4 Unicast is Enabled/Disabled on the connection to this peer .
ADR alaBgpPeer6Ipv6NextHop	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.67	Ipv6Address	read-write	The IPv6 nexthop address to be used for IPv6 routes advertised to this peer.
INT alaBgpPeer6Ipv6Unicast	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.60	INTEGER	read-only	Indicates whether the peer has advertised Multiprotocol IPv6 Unicast capability in its BGP OPEN message.
INT alaBgpPeer6KeepAlive	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.62	INTEGER	read-only	Time interval in seconds for the KeepAlive timer established with the peer. The value of this object is calculated by this BGP speaker such that, when compared with alaBgpPeer6HoldTime, it has the same proportion as what alaBgpPeer6KeepAliveConfigured has when compared with alaBgpPeer6HoldTimeConfigured. If the value of this object is zero (0), it indicates that the session has not been established with the peer, or, the value of alaBgpPeer6KeepAliveConfigured is zero (0).
INT alaBgpPeer6KeepAliveConfigured	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.65	INTEGER	read-write	Time interval in seconds for the KeepAlive timer configured for this BGP speaker with this peer. The value of this object will only determine the KEEPALIVE messages' frequency relative to the value specified in alaBgpPeer6HoldTimeConfigured; the actual time interval for the KEEPALIVE messages is indicated by alaBgpPeer6KeepAlive. A reasonable maximum value for this timer would be configured to be one third of that of alaBgpPeer6HoldTimeConfigured. If the value of this object is zero (0), no periodical KEEPALIVE messages are sent to the peer after the BGP connection has been established. The suggested value for this timer is 30 seconds.
INT alaBgpPeer6LastDownReason	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.18	INTEGER	read-only	The general reason for termination of last established session with the peer since the protocol was operationally up.
TIK alaBgpPeer6LastDownTime	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.19	TimeTicks	read-only	The time elapsed since the BGP session with the peer was terminated.
TIK alaBgpPeer6LastReadTime	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.20	TimeTicks	read-only	The time elapsed since we last read data from the peer.
INT alaBgpPeer6LastRecvNotifyReason	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.24	INTEGER	read-only	The last notification reason received.
INT alaBgpPeer6LastSentNotifyReason	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.23	INTEGER	read-only	The last notification reason sent.
TIK alaBgpPeer6LastTransitionTime	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.53	TimeTicks	read-only	The time elapsed since the BGP session was operationally up or down to the peer.
TIK alaBgpPeer6LastUpTime	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.54	TimeTicks	read-only	The time elapsed since the BGP session with the peer was established.
TIK alaBgpPeer6LastWriteTime	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.48	TimeTicks	read-only	The time elapsed since we last sent data to the peer.
ADR alaBgpPeer6LocalAddr	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.17	Ipv6Address	read-write	Local IPv6 address of this connection.
STR alaBgpPeer6LocalIntfName	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.56	DisplayString	read-write	The user defined name used to identify the local IPv6 interface for this peer's TCP connection.
INT alaBgpPeer6LocalPort	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.70	INTEGER	read-only	The local port number for this peer's TCP connection.
G32 alaBgpPeer6MaxPrefix	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.6	Gauge32	read-write	The maximum prefixes to be accepted from this peer. If this maximum is reached, the peer will be sent a NOTIFY message with a CEASE ecode.
INT alaBgpPeer6MaxPrefixWarnOnly	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.7	INTEGER	read-write	If enabled, the operator will be warned when the peer reaches 80% of the configured maximum prefixes. To see this message, BGP debug for type 'warnings' must be activated and debug level set to 20.
STR alaBgpPeer6MD5Key	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.44	DisplayString	read-write	Value of the MD5 key used in TCP connection with the peer. This field is secured and returned value is non significant.
OCT alaBgpPeer6MD5KeyEncrypt	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.45	OCTET STRING	read-only	Value of the MD5 key encrypted using 3DES algorithm. It is calculated from MD5 key value, and is used only to restore configuration on reboot.
INT alaBgpPeer6MinRouteAdvertisementInterval	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.73	INTEGER	read-write	Time interval in seconds for the MinRouteAdvertisementInterval timer.
INT alaBgpPeer6MultiHop	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.5	INTEGER	read-write	If enabled the external peer is allowed to be multiple hops away.
STR alaBgpPeer6Name	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.4	DisplayString	read-write	A symbolic name for the neighbour.
INT alaBgpPeer6NextHopSelf	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.8	INTEGER	read-write	If enabled, nexthop processing in the updates sent to this peer is disabled and is set to the IPv6 address of the interface attached to this peer.
INT alaBgpPeer6Passive	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.3	INTEGER	read-write	Enable/Disable the peer passive status. If enabled the peer will not initiate a transport connection.
STR alaBgpPeer6Prefix6ListIn	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.75	DisplayString	read-write	The name of the prefix6-list to be applied to the updates received from this peer. This is same as alaBgpPrefix6MatchListId.
STR alaBgpPeer6Prefix6ListOut	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.74	DisplayString	read-write	The name of the prefix6-list to be applied to the updates sent to this peer. This is same as alaBgpPrefix6MatchListId.
STR alaBgpPeer6PrefixListIn	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.37	DisplayString	read-write	The name of the prefix-list to be applied to the updates received from this peer. This is same as alaBgpPrefixMatchListId.
STR alaBgpPeer6PrefixListOut	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.36	DisplayString	read-write	The name of the prefix-list to be applied to the updates sent to this peer. This is same as alaBgpPrefixMatchListId.
C32 alaBgpPeer6RcvdMsgs	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.49	Counter32	read-only	The Number of messages received from the peer.
C32 alaBgpPeer6RcvdNotifyMsgs	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.21	Counter32	read-only	The Number of notification messages received from this peer.
C32 alaBgpPeer6RcvdPrefixes	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.25	Counter32	read-only	The Number of prefixes received from this peer.
C32 alaBgpPeer6RcvdRtRefreshMsgs	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.13	Counter32	read-only	The number of route refresh messages received from this peer.
C32 alaBgpPeer6RcvdUpdMsgs	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.51	Counter32	read-only	The Number of update messages received from the peer.
INT alaBgpPeer6ReconfigureInBound	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.42	INTEGER	read-write	Setting a value of reconfigure into this variable will re-start inbound policy evaluation of the peer.
INT alaBgpPeer6ReconfigureOutBound	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.43	INTEGER	read-write	Setting a value of reconfigure into this variable will re-start outbound policy evaluation of the peer.
INT alaBgpPeer6RemovePrivateAs	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.32	INTEGER	read-write	If enabled private as numbers are stripped out in the updates sent to this peer.
INT alaBgpPeer6Restart	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.40	INTEGER	read-write	Setting a value of restart into this variable will restart the peer.
INT alaBgpPeer6RestartFwdState	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.59	INTEGER	read-only	Indicates whether the peer has preserved the forwarding state during the graceful restart. This value is defined only for a peer that has advertised graceful restart capability. For peers that are not capable of graceful restart, this value will be notPreserved.
INT alaBgpPeer6RestartState	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.58	INTEGER	read-only	Indicates whether the peer is currently performing a graceful restart. A value of none indicates that this peer is not capable of graceful restart.
INT alaBgpPeer6RestartTime	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.57	INTEGER	read-only	The graceful restart time interval advertised by this peer. A value of 0 indicates that this peer is not capable of graceful restart, and has not advertised this capability.
STR alaBgpPeer6RouteMapIn	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.16	DisplayString	read-write	The name of the policy map to be applied to the updates received from this peer. This is same as alaBgpPolicyRouteMapName.
STR alaBgpPeer6RouteMapOut	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.15	DisplayString	read-write	The name of the policy map to be applied to the updates sent to this peer. This is same as alaBgpPolicyRouteMapName.
ROW alaBgpPeer6RowStatus	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.46	RowStatus	read-write	Row status variable.
C32 alaBgpPeer6SentMsgs	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.50	Counter32	read-only	The Number of messages sent to the peer.
C32 alaBgpPeer6SentNotifyMsgs	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.22	Counter32	read-only	The Number of notification messages sent to this peer.
C32 alaBgpPeer6SentRtRefreshMsgs	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.14	Counter32	read-only	The number of route refresh messages sent to this peer.
C32 alaBgpPeer6SentUpdMsgs	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.52	Counter32	read-only	The Number of update messages sent to the peer.
INT alaBgpPeer6SoftReconfig	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.9	INTEGER	read-write	Enable/Disable dynamic policy configurability on the connection to this peer.
INT alaBgpPeer6State	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.69	INTEGER	read-only	The BGP peer connection state.
alaBgpPeer6Table	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14		not-accessible	BGP IPv6 peer table.
INT alaBgpPeer6TcpWindowSize	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.71	INTEGER	read-only	The size of the socket buffers, in bytes, used for this TCP connection.
INT alaBgpPeer6TTL	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.33	INTEGER	read-write	TTL count for packets on this TCP connection.
INT alaBgpPeer6Type	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.27	INTEGER	read-only	This indicates whether the peer belongs to the local autonomous system(internal) or another autonomous system.
C32 alaBgpPeer6UpTransitions	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.14.1.47	Counter32	read-only	The Number of times this peer session transitioned to ESTABLISHED state.
INT alaBgpPeerActivateIpv6	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.64	INTEGER	read-create	If enabled, the Multiprotocol IPv6 Unicast capability is advertised to this peer. If disabled, the capability is not advertised in the OPEN message.
IP alaBgpPeerAddr	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.1	IpAddress	read-only	Ip Address of the peer.
INT alaBgpPeerAS	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.2	INTEGER	read-create	Autonomous system of the peer.
STR alaBgpPeerAspathListIn	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.35	DisplayString	read-create	The name of the aspath-list to be applied to the updates received from this peer. This is same as alaBgpAspathMatchListId.
STR alaBgpPeerAspathListOut	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.34	DisplayString	read-create	The name of the aspath-list to be applied to the updates sent to this peer. This is same as alaBgpAspathMatchListId.
INT alaBgpPeerAutoReStart	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.29	INTEGER	read-create	Enable/Disable the peer autostart status. If enabled, the peer will be automatically restarted (if administratively enabled) after the transition to IDLE state.
INT alaBgpPeerBfdStatus	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.65	INTEGER	read-create	Enables/Disables BFd for a particular Peer.
IP alaBgpPeerBgpId	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.55	IpAddress	read-only	BGP Identifier of the peer.
INT alaBgpPeerChanges	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.17	INTEGER	read-write	Enable/Disable logging of peer state changes to the syslog.
INT alaBgpPeerClearCounter	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.28	INTEGER	read-create	Setting a value of clear into this variable will clear the per peer statistics.
INT alaBgpPeerClientStatus	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.30	INTEGER	read-create	If enabled this peer is a route reflection client.
STR alaBgpPeerCommunityListIn	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.39	DisplayString	read-create	The name of the community-list to be applied to the updates received from this peer. This is same as alaBgpCommunityMatchListId.
STR alaBgpPeerCommunityListOut	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.38	DisplayString	read-create	The name of the community-list to be applied to the updates sent to this peer. This is same as alaBgpCommunityMatchListId.
INT alaBgpPeerConfedStatus	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.31	INTEGER	read-create	If enabled this peer is a member of our confederation.
INT alaBgpPeerDefaultOriginate	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.41	INTEGER	read-create	If enabled a default route is sent to this neighbour.
C32 alaBgpPeerDownTransitions	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.26	Counter32	read-only	The Number of times this peer session transitioned to IDLE state.
alaBgpPeerEntry	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1		not-accessible	BGP IPv4 Peer configuration entry.
INT alaBgpPeerInSoftReset	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.10	INTEGER	read-only	Route refresh capability is Enabled/Disabled on the connection to this peer.
INT alaBgpPeerIpv4Multicast	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.12	INTEGER	read-only	Multiprotocol capability IPv4 Multicast is Enabled/Disabled on the connection to this peer .
INT alaBgpPeerIpv4Unicast	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.11	INTEGER	read-only	Multiprotocol capability IPv4 Unicast is Enabled/Disabled on the connection to this peer .
ADR alaBgpPeerIpv6NextHop	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.61	Ipv6Address	read-create	The IPv6 nexthop for IPv6 routes advertised to this peer.
INT alaBgpPeerIpv6Unicast	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.60	INTEGER	read-only	Indicates whether the peer has advertised Multiprotocol IPv6 Unicast capability in its BGP OPEN message.
INT alaBgpPeerLastDownReason	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.18	INTEGER	read-only	The general reason for termination of last established session with the peer since the protocol was operationally up.
TIK alaBgpPeerLastDownTime	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.19	TimeTicks	read-only	The time elapsed since the BGP session with the peer was terminated.
TIK alaBgpPeerLastReadTime	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.20	TimeTicks	read-only	The time elapsed since we last read data from the peer.
INT alaBgpPeerLastRecvNotifyReason	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.24	INTEGER	read-only	The last notification reason received.
INT alaBgpPeerLastSentNotifyReason	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.23	INTEGER	read-only	The last notification reason sent.
TIK alaBgpPeerLastTransitionTime	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.53	TimeTicks	read-only	The time elapsed since the BGP session was operationally up or down to the peer.
TIK alaBgpPeerLastUpTime	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.54	TimeTicks	read-only	The time elapsed since the BGP session with the peer was established.
TIK alaBgpPeerLastWriteTime	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.48	TimeTicks	read-only	The time elapsed since we last sent data to the peer.
IP alaBgpPeerLocalAddr	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.17	IpAddress	read-create	Local Ip Address of this connection.
STR alaBgpPeerLocalIntfName	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.56	DisplayString	read-only	The user defined name used to identify the local IP interface for this peer's TCP connection.
INT alaBgpPeerLocalPort	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.62	INTEGER	read-only	The local port number for this peer's TCP connection.
G32 alaBgpPeerMaxPrefix	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.6	Gauge32	read-create	The maximum prefixes to be accepted from this peer. If this maximum is reached, the peer will be sent a NOTIFY message with a CEASE ecode.
INT alaBgpPeerMaxPrefixWarnOnly	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.7	INTEGER	read-create	If enabled, the operator will be warned when the peer reaches 80% of the configured maximum prefixes. To see this message, BGP debug for type 'warnings' must be activated and debug level set to 20.
STR alaBgpPeerMD5Key	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.44	DisplayString	read-create	Value of the MD5 key used in TCP connection with the peer. This field is secured and returned value is non significant.
OCT alaBgpPeerMD5KeyEncrypt	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.45	OCTET STRING	read-only	Value of the MD5 key encrypted using 3DES algorithm. It is calculated from MD5 key value, and is used only to restore configuration on reboot.
INT alaBgpPeerMultiHop	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.5	INTEGER	read-create	If enabled the external peer is allowed to be multiple hops away.
STR alaBgpPeerName	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.4	DisplayString	read-create	A symbolic name for the neighbour.
INT alaBgpPeerNextHopSelf	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.8	INTEGER	read-create	If enabled, nexthop processing in the updates sent to this peer is disabled and is set to the ip address of the interface attached to this peer.
INT alaBgpPeerPassive	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.3	INTEGER	read-create	Enable/Disable the peer passive status. If enabled the peer will not initiate a transport connection.
STR alaBgpPeerPrefix6ListIn	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.67	DisplayString	read-create	The name of the prefix6-list to be applied to the updates received from this peer. This is same as alaBgpPrefix6MatchListId.
STR alaBgpPeerPrefix6ListOut	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.66	DisplayString	read-create	The name of the prefix6-list to be applied to the updates sent to this peer. This is same as alaBgpPrefix6MatchListId.
STR alaBgpPeerPrefixListIn	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.37	DisplayString	read-create	The name of the prefix-list to be applied to the updates received from this peer. This is same as alaBgpPrefixMatchListId.
STR alaBgpPeerPrefixListOut	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.36	DisplayString	read-create	The name of the prefix-list to be applied to the updates sent to this peer. This is same as alaBgpPrefixMatchListId.
C32 alaBgpPeerRcvdMsgs	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.49	Counter32	read-only	The Number of messages received from the peer.
C32 alaBgpPeerRcvdNotifyMsgs	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.21	Counter32	read-only	The Number of notification messages received from this peer.
C32 alaBgpPeerRcvdPrefixes	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.25	Counter32	read-only	The Number of prefixes received from this peer.
C32 alaBgpPeerRcvdRtRefreshMsgs	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.13	Counter32	read-only	The number of route refresh messages received from this peer.
C32 alaBgpPeerRcvdUpdMsgs	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.51	Counter32	read-only	The Number of update messages received from the peer.
INT alaBgpPeerReconfigureInBound	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.42	INTEGER	read-create	Setting a value of reconfigure into this variable will re-start inbound policy evaluation of the peer.
INT alaBgpPeerReconfigureOutBound	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.43	INTEGER	read-create	Setting a value of reconfigure into this variable will re-start outbound policy evaluation of the peer.
INT alaBgpPeerRemovePrivateAs	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.32	INTEGER	read-create	If enabled private as numbers are stripped out in the updates sent to this peer.
INT alaBgpPeerRestart	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.40	INTEGER	read-create	Setting a value of restart into this variable will restart the peer.
INT alaBgpPeerRestartFwdState	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.59	INTEGER	read-only	Indicates whether the peer has preserved the forwarding state during the graceful restart. This value is defined only for a peer that has advertised graceful restart capability. For peers that are not capable of graceful restart, this value will be notPreserved.
INT alaBgpPeerRestartState	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.58	INTEGER	read-only	Indicates whether the peer is currently performing a graceful restart. A value of none indicates that this peer is not capable of graceful restart.
INT alaBgpPeerRestartTime	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.57	INTEGER	read-only	The graceful restart time interval advertised by this peer. A value of 0 indicates that this peer is not capable of graceful restart, and has not advertised this capability.
STR alaBgpPeerRouteMapIn	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.16	DisplayString	read-create	The name of the policy map to be applied to the updates received from this peer. This is same as alaBgpPolicyRouteMapName.
STR alaBgpPeerRouteMapOut	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.15	DisplayString	read-create	The name of the policy map to be applied to the updates sent to this peer. This is same as alaBgpPolicyRouteMapName.
ROW alaBgpPeerRowStatus	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.46	RowStatus	read-create	Row status variable.
C32 alaBgpPeerSentMsgs	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.50	Counter32	read-only	The Number of messages sent to the peer.
C32 alaBgpPeerSentNotifyMsgs	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.22	Counter32	read-only	The Number of notification messages sent to this peer.
C32 alaBgpPeerSentRtRefreshMsgs	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.14	Counter32	read-only	The number of route refresh messages sent to this peer.
C32 alaBgpPeerSentUpdMsgs	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.52	Counter32	read-only	The Number of update messages sent to the peer.
INT alaBgpPeerSoftReconfig	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.9	INTEGER	read-create	Enable/Disable dynamic policy configurability on the connection to this peer.
alaBgpPeerTable	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2		not-accessible	BGP IPv4 peer table.
INT alaBgpPeerTcpWindowSize	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.63	INTEGER	read-only	The size of the socket buffers, in bytes, used for this TCP connection.
INT alaBgpPeerTTL	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.33	INTEGER	read-create	TTL count for packets on this TCP connection.
INT alaBgpPeerType	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.27	INTEGER	read-only	This indicates whether the peer belongs to the local autonomous system(internal) or another autonmous system.
C32 alaBgpPeerUpTransitions	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.2.1.47	Counter32	read-only	The Number of times this peer session transitioned to ESTABLISHED state.
alaBgpPolicy	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8
INT alaBgpPrefix6MatchListAction	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.7.1.6	INTEGER	read-create	This determines whether to accept or reject a matching route.
ADR alaBgpPrefix6MatchListAddr	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.7.1.2	Ipv6Address	not-accessible	The IPv6 Prefix to be matched. A value of 0 indicates default route prefix.
INT alaBgpPrefix6MatchListAddrLength	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.7.1.3	INTEGER	not-accessible	The length in bits of the IPv6 prefix being matched. A value of 0 indicates default route prefix.
alaBgpPrefix6MatchListEntry	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.7.1		not-accessible	BGP Prefix6 matching instance.
INT alaBgpPrefix6MatchListGE	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.7.1.4	INTEGER	read-create	Specifies the minimum length of the mask to be matched. A value of 0 means this criteria is absent. The value of alaBgpPrefix6MatchListGE must be > length of (alaBgpPrefix6MatchListAddrLength) and < alaBgpPrefix6MatchListLE.
STR alaBgpPrefix6MatchListId	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.7.1.1	DisplayString	not-accessible	Identifier of this list of autonomous system path matching criteria.
INT alaBgpPrefix6MatchListLE	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.7.1.5	INTEGER	read-create	Specifies the maximum length (inclusive) of the mask to be matched. A value of 0 means this criteria is absent. The value of alaBgpPrefix6MatchListLE must be >= alaBgpPrefix6MatchListGE and <= 32.
ROW alaBgpPrefix6MatchListRowStatus	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.7.1.7	RowStatus	read-create	Row status variable
alaBgpPrefix6MatchListTable	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.7		not-accessible	BGP Policy prefix6 matching criteria table.
INT alaBgpPrefixMatchListAction	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.3.1.6	INTEGER	read-write	This determines whether to accept or reject a matching route.
IP alaBgpPrefixMatchListAddr	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.3.1.2	IpAddress	read-only	The address to be matched.
alaBgpPrefixMatchListEntry	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.3.1		not-accessible	BGP Prefix matching instance.
INT alaBgpPrefixMatchListGE	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.3.1.4	INTEGER	read-write	Specifies the minimum length of the mask to be matched. A value of 0 means this criteria is absent. The value of alaBgpPrefixMatchListGE must be > length of (alaBgpPrefixMatchListMask) and < alaBgpPrefixMatchListLE.
STR alaBgpPrefixMatchListId	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.3.1.1	DisplayString	read-only	Identifier of this list of autonomous system path matching criteria.
INT alaBgpPrefixMatchListLE	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.3.1.5	INTEGER	read-write	Specifies the maximum length (inclusive) of the mask to be matched. A value of 0 means this criteria is absent. The value of alaBgpPrefixMatchListLE must be >= alaBgpPrefixMatchListGE and <= 32.
IP alaBgpPrefixMatchListMask	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.3.1.3	IpAddress	read-only	The mask to be matched.
ROW alaBgpPrefixMatchListRowStatus	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.3.1.7	RowStatus	read-write	Row status variable
alaBgpPrefixMatchListTable	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.3		not-accessible	BGP Policy prefix matching criteria table.
INT alaBgpPromiscuousNeighbours	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.9	INTEGER	read-write	Enable/Disable BGP to accept connections from neighbours that are not configured.
INT alaBgpProtoOperState	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.19	INTEGER	read-only	The BGP protocol operational state.
INT alaBgpProtoStatus	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.1	INTEGER	read-write	Enable/Disable BGP protocol
STR alaBgpRedistRouteCommunity	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.9.1.6	DisplayString	read-write	The value to set the COMMUNITY attribute when advertising this network. This object has been deprecated. Use alaRouteMapRedistProtoEntry objects of AlcatelIND1RouteMap.mib.
IP alaBgpRedistRouteDest	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.9.1.2	IpAddress	read-only	The destination IP address of this route. This object has been deprecated. Use alaRouteMapRedistProtoEntry objects of AlcatelIND1RouteMap.mib.
INT alaBgpRedistRouteEffect	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.9.1.8	INTEGER	read-write	Controls the redistribution of routes in this range. This object has been deprecated. Use alaRouteMapRedistProtoEntry objects of AlcatelIND1RouteMap.mib.
alaBgpRedistRouteEntry	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.9.1		not-accessible	A configuration table which controls the routes to be redistributed by BGP from other routing protocols. This entry has been deprecated. Use the alaRouteMapRedistProtoEntry of AlcatelIND1RouteMap.mib.
G32 alaBgpRedistRouteLocalPref	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.9.1.5	Gauge32	read-write	The value to override the default local pref sent to internal peers. If 0, no override is applied. This object has been deprecated. Use alaRouteMapRedistProtoEntry objects of AlcatelIND1RouteMap.mib.
IP alaBgpRedistRouteMask	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.9.1.3	IpAddress	read-only	The network mask for this route. This object has been deprecated. Use alaRouteMapRedistProtoEntry objects of AlcatelIND1RouteMap.mib.
G32 alaBgpRedistRouteMetric	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.9.1.4	Gauge32	read-write	The med to be sent to external peers. If 0, no med is sent. This object has been deprecated. Use alaRouteMapRedistProtoEntry objects of AlcatelIND1RouteMap.mib.
INT alaBgpRedistRouteProto	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.9.1.1	INTEGER	read-write	Protocol from where this route is to be imported from. This object has been deprecated. Use alaRouteMapRedistProtoEntry objects of AlcatelIND1RouteMap.mib.
ROW alaBgpRedistRouteRowStatus	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.9.1.9	RowStatus	read-write	Row status variable. This object has been deprecated. Use alaRouteMapRedistProtoEntry objects of AlcatelIND1RouteMap.mib.
INT alaBgpRedistRouteSubnetMatch	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.9.1.7	INTEGER	read-write	Redistribute all the subnet routes if it is enabled. Otherwise, redistribute only matching network route. This object has been deprecated. Use alaRouteMapRedistProtoEntry objects of AlcatelIND1RouteMap.mib.
alaBgpRedistRouteTable	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.9		not-accessible	A configuration table which controls the routes to be redistributed by BGP from other routing protocols. This table has been deprecated. Use the alaRouteMapRedistProtoTable of AlcatelIND1RouteMap.mib.
INT alaBgpRestartInterval	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.40	INTEGER	read-write	Determines how long, in seconds, peering BGP routers are told to wait for this router to complete graceful restart and re-establish peering session. It is recommended that this value not be more than the configured Hold Time interval.
INT alaBgpRestartStatus	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.41	INTEGER	read-only	Indicates whether the router is currently performing a graceful restart.
ADR alaBgpRoute6Addr	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.12.1.1	Ipv6Address	read-only	Destination address.
STR alaBgpRoute6AdvNeighbors	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.12.1.11	DisplayString	read-only	List of (addresses of) neighbours to whom this route has been advertised is encoded here.
alaBgpRoute6Entry	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.12.1		not-accessible	BGP Route entry.
C32 alaBgpRoute6FeasiblePaths	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.12.1.5	Counter32	read-only	Number of Feasible paths available to this destination.
ADR alaBgpRoute6IgpNextHop	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.12.1.7	Ipv6Address	read-only	The IGP Nexthop to reach this destination.
INT alaBgpRoute6IsAggregate	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.12.1.9	INTEGER	read-only	Indicates whether the route is an aggregate.
INT alaBgpRoute6IsAggregateContributor	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.12.1.10	INTEGER	read-only	Indicates whether the route is a contributor to an aggregate.
INT alaBgpRoute6IsAggregateList	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.12.1.12	INTEGER	read-only	Indicates whether the route is on an aggregate list.
INT alaBgpRoute6IsAggregateWait	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.12.1.13	INTEGER	read-only	Indicates whether the route is an aggregate waiting for a contributor.
INT alaBgpRoute6IsDampened	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.12.1.19	INTEGER	read-only	Indicates whether the route is being route flap dampened.
INT alaBgpRoute6IsHidden	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.12.1.8	INTEGER	read-only	Indicates whether the route is hidden by an aggregate.
INT alaBgpRoute6IsOnDeleteList	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.12.1.18	INTEGER	read-only	Indicates whether the route is placed on delete list.
INT alaBgpRoute6IsOnEbgpChgList	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.12.1.14	INTEGER	read-only	Indicates whether the route is placed on list of EBGP routes.
INT alaBgpRoute6IsOnIbgpChgList	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.12.1.16	INTEGER	read-only	Indicates whether the route is placed on list of IBGP non-reflector-client routes.
INT alaBgpRoute6IsOnIbgpClientChgList	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.12.1.15	INTEGER	read-only	Indicates whether the route is placed on list of IBGP reflector-client routes.
INT alaBgpRoute6IsOnLocalChgList	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.12.1.17	INTEGER	read-only	Indicates whether the route is placed on list of local routes.
U32 alaBgpRoute6MaskLen	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.12.1.2	Unsigned32	read-only	Destination address length.
ADR alaBgpRoute6NextHop	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.12.1.6	Ipv6Address	read-only	The BGP Nexthop to reach this destination.
C32 alaBgpRoute6Paths	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.12.1.4	Counter32	read-only	Number of total paths available to this destination.
INT alaBgpRoute6State	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.12.1.3	INTEGER	read-only	Indicates whether the route is being actively advertised or not.
alaBgpRoute6Table	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.12		not-accessible	BGP IPv6 Routing table.
IP alaBgpRouteAddr	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.5.1.1	IpAddress	read-only	Destination address.
STR alaBgpRouteAdvNeighbors	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.5.1.11	DisplayString	read-only	List of (addresses of) neighbours to whom this route has been advertised is encoded here.
alaBgpRouteEntry	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.5.1		not-accessible	BGP Route entry.
C32 alaBgpRouteFeasiblePaths	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.5.1.5	Counter32	read-only	Number of Feasible paths available to this destination.
IP alaBgpRouteIgpNextHop	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.5.1.7	IpAddress	read-only	The IGP Nexthop to reach this destination.
INT alaBgpRouteIsAggregate	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.5.1.9	INTEGER	read-only	Indicates whether the route is an aggregate.
INT alaBgpRouteIsAggregateContributor	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.5.1.10	INTEGER	read-only	Indicates whether the route is a contributor to an aggregate.
INT alaBgpRouteIsAggregateList	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.5.1.12	INTEGER	read-only	Indicates whether the route is on an aggregate list.
INT alaBgpRouteIsAggregateWait	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.5.1.13	INTEGER	read-only	Indicates whether the route is an aggregate waiting for a contributor.
INT alaBgpRouteIsDampened	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.5.1.19	INTEGER	read-only	Indicates whether the route is being route flap dampened.
INT alaBgpRouteIsHidden	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.5.1.8	INTEGER	read-only	Indicates whether the route is hidden by an aggregate.
INT alaBgpRouteIsOnDeleteList	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.5.1.18	INTEGER	read-only	Indicates whether the route is placed on delete list.
INT alaBgpRouteIsOnEbgpChgList	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.5.1.14	INTEGER	read-only	Indicates whether the route is placed on list of EBGP routes.
INT alaBgpRouteIsOnIbgpChgList	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.5.1.16	INTEGER	read-only	Indicates whether the route is placed on list of IBGP non-reflector-client routes.
INT alaBgpRouteIsOnIbgpClientChgList	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.5.1.15	INTEGER	read-only	Indicates whether the route is placed on list of IBGP reflector-client routes.
INT alaBgpRouteIsOnLocalChgList	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.5.1.17	INTEGER	read-only	Indicates whether the route is placed on list of local routes.
INT alaBgpRouteMapAction	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.1.1.19	INTEGER	read-write	This determines whether to allow a matching route to pass through.
STR alaBgpRouteMapAsPathMatchListId	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.1.1.3	DisplayString	read-write	This is same as alaBgpAspathMatchListId. It identifies the matching criteria list of Autonomous system paths. Empty quotes indicate no autonomous system paths matching criteria is to be applied.
STR alaBgpRouteMapAsPrepend	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.1.1.11	DisplayString	read-write	The value to prepend to the AS_PATH attribute of the routes matched by this RouteMap instance. Empty quotes indicates no AS_PATH prepending is to be done.
STR alaBgpRouteMapCommunity	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.1.1.13	DisplayString	read-write	The value to set the COMMUNITY attribute of the routes matched by this RouteMap instance.
STR alaBgpRouteMapCommunityMatchListId	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.1.1.5	DisplayString	read-write	This is same as alaBgpCommunityMatchListId. It identifies the matching criteria list of communities. Empty quotes indicate no community matching criteria is to be applied.
alaBgpRouteMapEntry	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.1.1		not-accessible	BGP Route Map Entry.
INT alaBgpRouteMapInst	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.1.1.2	INTEGER	read-only	Instance of this route map.
G32 alaBgpRouteMapLocalPref	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.1.1.7	Gauge32	read-write	The value to set the LOCAL PREF attribute of the routes matched by this RouteMap instance. This value is added to/is subtracted from/replaces the LOCAL PREF attribute in conjunction with the associated value of alaBgpRouteMapLocalPrefMode.
INT alaBgpRouteMapLocalPrefMode	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.1.1.8	INTEGER	read-write	This variable specifies how alaBgpRouteMapLocalPref is to be operated on an existing LPREF attribute of a route on which this RouteMap instance is applied to.
STR alaBgpRouteMapMatchAsRegExp	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.1.1.14	DisplayString	read-write	AsPath regular expression matching primitive.
STR alaBgpRouteMapMatchCommunity	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.1.1.17	DisplayString	read-write	Community match primitive
IP alaBgpRouteMapMatchMask	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.1.1.16	IpAddress	read-write	Prefix match mask primitive
IP alaBgpRouteMapMatchPrefix	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.1.1.15	IpAddress	read-write	Prefix match primitive.
G32 alaBgpRouteMapMed	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.1.1.9	Gauge32	read-write	The value to set the MULTI EXIT DISC attribute of the routes matched by this RouteMap instance. This value is added to/is subtracted from/replaces the MULTI EXIT DISC attribute in conjunction with the associated value of alaBgpRouteMapMedMode.
INT alaBgpRouteMapMedMode	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.1.1.10	INTEGER	read-write	This variable specifies how alaBgpRouteMapMed is to be operated on an existing MULTI EXIT DISC attribute of a route on which this RouteMap instance is applied to.
STR alaBgpRouteMapName	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.1.1.1	DisplayString	read-only	Name of the route map.
INT alaBgpRouteMapOrigin	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.1.1.6	INTEGER	read-write	The value to set the origin of the routes matched by this RouteMap instance. A value of none means no origin is to be set.
STR alaBgpRouteMapPrefixMatchListId	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.1.1.4	DisplayString	read-write	This is same as alaBgpPrefixMatchListId. It identifies the matching criteria list of prefixes. Empty quotes indicate no prefix matching criteria is to be applied.
ROW alaBgpRouteMapRowStatus	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.1.1.20	RowStatus	read-write	Row status variable
INT alaBgpRouteMapSetCommunityMode	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.1.1.12	INTEGER	read-write	Determines whether alaBgpRouteMapCommunity will be adding to or replacing the COMMUNITY attribute of the routes matched by this RouteMap instance.
alaBgpRouteMapTable	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.1		not-accessible	BGP Policy RouteMap table.
INT alaBgpRouteMapWeight	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.8.1.1.18	INTEGER	read-write	This sets the weight for the incoming route. This parameter has no effect on outbound policy.
IP alaBgpRouteMask	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.5.1.2	IpAddress	read-only	Destination Mask.
IP alaBgpRouteNextHop	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.5.1.6	IpAddress	read-only	The BGP Nexthop to reach this destination.
C32 alaBgpRoutePaths	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.5.1.4	Counter32	read-only	Number of total paths available to this destination.
INT alaBgpRouteReflection	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.30	INTEGER	read-write	Enable/Disable Route reflection
IP alaBgpRouterId	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.3	IpAddress	read-only	Configured BGP router ID.
INT alaBgpRouteState	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.5.1.3	INTEGER	read-only	Indicates whether the route is being actively advertised or not.
alaBgpRouteTable	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.5		not-accessible	BGP Routing table.
INT alaBgpVersion	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1.1.18	INTEGER	read-only	The BGP Version in use.
alcatelIND1BGPMIB	1.3.6.1.4.1.6486.801.1.2.1.10.5.1			This module describes an authoritative enterprise-specific Simple Network Management Protocol (SNMP) Management Information Base (MIB): For the Birds Of Prey Product Line Configuration Of Global BGP Configuration Parameters. The right to make changes in specification and other information contained in this document without prior notice is reserved. No liability shall be assumed for any incidental, indirect, special, or consequential damages whatsoever arising from or related to this document or the information contained herein. Vendors, end-users, and other interested parties are granted non-exclusive license to use this specification in connection with management of the products for which it is intended to be used. Copyright (C) 1995-2007 Alcatel-Lucent ALL RIGHTS RESERVED WORLDWIDE
alcatelIND1BGPMIBCompliance	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.2.2.1			The compliance statement for entities which implement the BGP4 mib.
alcatelIND1BGPMIBCompliances	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.2.2			Branch For Border Gateway Protocol (BGP) Subsystem Compliance Statements.
alcatelIND1BGPMIBConformance	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.2			Branch For Border Gateway Protocol (BGP) Subsystem Conformance Information.
alcatelIND1BGPMIBGroups	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.2.1			Branch For Border Gateway Protocol (BGP) Subsystem Units Of Conformance.
alcatelIND1BGPMIBObjects	1.3.6.1.4.1.6486.801.1.2.1.10.5.1.1			Branch For Border Gateway Protocol (BGP) Subsystem Managed Objects.

RFC description

Provides configuration and monitoring of BGP (Border Gateway Protocol) for Alcatel-Lucent enterprise routing systems.

Start monitoring Alcatel-Lucent Enterprise OmniSwitch switches with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ALCATEL-IND1-BGP-MIB