All MIBs › ALCATEL-IND1-NTP-MIB
Organization: Alcatel-Lucent
Last Updated: 2010-05-13
Category: IP and Core Protocols, Vendor: Alcatel-Lucent
Description: Alcatel OmniSwitch NTP client/server MIB for managing time synchronization servers, keys, and stratum settings.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is ALCATEL-IND1-NTP-MIB?
ALCATEL-IND1-NTP-MIB is an Alcatel (now Alcatel-Lucent Enterprise) proprietary MIB for the OmniSwitch line, covering configuration and monitoring of the switch's Network Time Protocol (NTP) client and server functions. It exposes data on NTP operating mode (enable/disable, broadcast mode, monitoring), and a peer table listing each configured time-source peer along with its address, type, authentication settings, protocol version, and polling interval. As a monitoring tool it is used to verify that the switch's software clock-synchronization service is healthy, confirming NTP is enabled, that configured peers are reachable and correctly authenticated, and that time sync has not silently failed, which matters because clock drift on a switch can corrupt log timestamps and break certificate/security validation. It is a self-contained enterprise MIB but conceptually parallels the IETF NTP model even though it does not formally import the standard NTPv4 MIB. It is typically deployed on Alcatel-Lucent OmniSwitch campus/data-center switches to keep switch clocks synchronized with upstream time servers. Engineers can download the ALCATEL-IND1-NTP-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in ALCATEL-IND1-NTP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Alcatel-Lucent OmniSwitch enterprise/campus switches
Monitoring Examples
An administrator would check alaNtpEnable and alaNtpMonitorEnable to confirm NTP service and monitoring are turned on, then walk alaNtpPeerTable/alaNtpPeerEntry to see each configured peer's alaNtpPeerAddress, alaNtpPeerType, and alaNtpPeerAuth settings. A peer entry showing an unreachable alaNtpPeerIpAddress or failing alaNtpPeerAuth would indicate the switch has lost its authenticated time source and may be drifting out of sync. Polling alaNtpPeerMinpoll alongside peer reachability helps confirm the switch is actually completing sync cycles rather than just having NTP configured.
What Can Be Monitored
- NTP client/server enable status
- NTP broadcast mode
- configured NTP peer list
- peer authentication status
- peer polling interval
- NTP monitoring status
This MIB depends on
Related MIBs
Imported Objects
From ALCATEL-IND1-BASE
| softentIND1Ntp | OBJECT-IDENTITY |
From INET-ADDRESS-MIB
| InetAddress | |
| InetAddressType |
From SNMP-FRAMEWORK-MIB
| SnmpAdminString |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-IDENTITY | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| RowStatus |
How to Use in IPNetwork Monitor
Example using alaNtpStatsStatUptime OID:
Select an Alcatel-Lucent Enterprise OmniSwitch switch as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type alaNtpStatsStatUptime into the Find box to locate it in the OID tree, then select it and click OK. The number of seconds the local NTP server has been associated with the switch. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the value is unexpectedly low (e.g. under 10 minutes), since that indicates a recent, possibly unplanned, reboot or restart. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| alcatelIND1NTPMIB | 1.3.6.1.4.1.6486.801.1.2.1.26.1 | This module describes an authoritative enterprise-specific Simple Network Management Protocol (SNMP) Management Information Base (MIB): Propietary NTP MIB definitions The right to make changes in specification and other information contained in this document without prior notice is reserved. No liability shall be assumed for any incidental, indirect, special, or consequential damages whatsoever arising from or related to this document or the information contained herein. Vendors, end-users, and other interested parties are granted non-exclusive license to use this specification in connection with management of the products for which it is intended to be used. Copyright (C) 1995-2007 Alcatel-Lucent ALL RIGHTS RESERVED WORLDWIDE | ||
| alcatelIND1NTPMIBNotifications | 1.3.6.1.4.1.6486.801.1.2.1.26.1.0 | Branch For NTP MIB Subsystem Notifications. | ||
| NTF alaNtpMaxAssocTrap | 1.3.6.1.4.1.6486.801.1.2.1.26.1.0.1 | Notify the management entity on reaching the maximum allowable NTP client and peer associations. | ||
| alcatelIND1NTPMIBObjects | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1 | Branch For NTP Subsystem Managed Objects. | ||
| alaNtpConfig | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.1 | |||
| INT alaNtpEnable | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.1.1 | INTEGER | read-write | Enables/disables NTP clock discipline. |
| INT alaNtpMonitorEnable | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.1.2 | INTEGER | read-write | Enables/disables NTP monitor. |
| INT alaNtpBroadcastEnable | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.1.3 | INTEGER | read-write | Enables/disables NTP broadcast client. |
| alaNtpPeerTable | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.1.4 | not-accessible | Table containing the synchronization host this switch will be associated with. | |
| alaNtpPeerEntry | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.1.4.1 | not-accessible | Each entry corresponds to a synchronization host. | |
| IPt alaNtpPeerAddressType | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.1.4.1.1 | InetAddressType | not-accessible | The InetAddress type of the synchronization host. Only types InetAddressIPv4 (1) and InetAddressDNS (16) are supported. |
| IP alaNtpPeerAddress | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.1.4.1.2 | InetAddress | not-accessible | The InetAddress of the synchronization host. |
| IP alaNtpPeerIpAddress | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.1.4.1.3 | IpAddress | read-only | The IP address of the synchronization host derrived from the InetAddress. |
| INT alaNtpPeerType | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.1.4.1.4 | INTEGER | read-create | Type of synchronization host that will communicate with this switch. |
| I32 alaNtpPeerAuth | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.1.4.1.5 | Integer32 | read-create | The authorization keyid for the remote host. |
| I32 alaNtpPeerVersion | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.1.4.1.6 | Integer32 | read-create | The NTP version to communicate with the remote host. |
| I32 alaNtpPeerMinpoll | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.1.4.1.7 | Integer32 | read-create | The minimum poll duration to the remote host. This value is a power of 2 seconds when the poll will occur. For example, 4 (2 to the power 4) is 16 seconds. The maximum poll value is 10. |
| INT alaNtpPeerPrefer | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.1.4.1.8 | INTEGER | read-create | Marks the host as a preferred connection. |
| ROW alaNtpPeerAdmin | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.1.4.1.9 | RowStatus | read-create | Used in accordance to installation and removal conventions for conceptual rows. The RowStatus values that are supported are the following: active(1) - The row is active and valid. createAndGo(4) - The row will be created and activated. destroy(6) - The row will be destroyed. |
| STR alaNtpPeerName | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.1.4.1.10 | SnmpAdminString | read-only | The DNS name for the peer association derrived from the InetAddress. |
| I32 alaNtpPeerStratum | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.1.4.1.11 | Integer32 | read-create | The stratum level of the remote peer. If this number is 16, the remote peer has not been synchronized. This parameter can only be set with a LOCALCLOCK server. |
| I32 alaNtpAuthDelay | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.1.5 | Integer32 | read-write | This field sets a specified time interval that is added to timestamps included in requests to the server that required authentication. Typically this delay is needed in cases of long delay paths, or servers whose clocks are unsynchronized. Value is in milli-seconds |
| I32 alaNtpBroadcastDelay | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.1.6 | Integer32 | read-write | This field sets a specified time interval that is added to timestamps included in messages from broadcast servers. Value is in milli-seconds |
| STR alaNtpKeysFile | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.1.7 | SnmpAdminString | read-only | Name of the file which has the authorization keys. |
| I32 alaNtpConfigReqKeyId | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.1.8 | Integer32 | read-write | Request messages ask for information from the NTP entity such as timestamp information, statistics, etc. This changes the authentication key identifier for request messages sent from the switch to another NTP entity. |
| I32 alaNtpConfigCtlKeyId | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.1.9 | Integer32 | read-write | Control messages attempt to change the configuration of the NTP entity in some fashion. This changes the authentication key identifier for control messages sent from the switch to another NTP entity. |
| I32 alaNtpConfigCfgKeyId | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.1.10 | Integer32 | read-write | Configuration messages changes information on the NTP entity. |
| I32 alaNtpPrecision | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.1.11 | Integer32 | read-write | This sets the server's advertised precision. |
| INT alaNtpPeerTests | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.1.12 | INTEGER | read-write | Enables/disable NTP peer synchronization tests. Disabling peer tests allows the NTP client to synchonize with servers that are themselves unsynchronized or would otherwise be eliminated by other time source tests. |
| I32 alaNtpSysStratum | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.1.13 | Integer32 | read-write | The stratum level of the local server. If this number is 16 it indicates that the switch is not synchronized. This helps the clients to select clocks with lower stratum number |
| I32 alaNtpMaxAssociation | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.1.14 | Integer32 | read-write | The maximum number of peer and client associations that the switch will serve. This helps ensure that the switch isn't overwhelmed by huge numbers of NTP synchronization requests |
| INT alaNtpAuthenticate | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.1.15 | INTEGER | read-write | Enable/Disable authentication of the NTP requests on the switch |
| alaNtpInfo | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2 | |||
| alaNtpPeerListTable | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.1 | not-accessible | Used to display a brief list of all NTP associations related to this switch (servers, peers, etc.). | |
| alaNtpPeerListEntry | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.1.1 | not-accessible | Each entry corresponds to one association. | |
| IPt alaNtpPeerListAddressType | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.1.1.1 | InetAddressType | not-accessible | The InetAddress type of the synchronization host. InetAddressIPv4 (1) is the only type currently supported. |
| IP alaNtpPeerListAddress | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.1.1.2 | InetAddress | not-accessible | The InetAddress of the association. |
| IP alaNtpPeerListIpAddress | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.1.1.3 | IpAddress | read-only | The IP address of the association. |
| IP alaNtpPeerListLocal | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.1.1.4 | IpAddress | read-only | The local interface address assigned by NTP to the remote association. If this address is 0.0.0.0, then the local address has yet to be determined. |
| I32 alaNtpPeerListStratum | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.1.1.5 | Integer32 | read-only | The stratum level of the remote peer. If this number is 16, the remote peer has not been synchronized. |
| I32 alaNtpPeerListPoll | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.1.1.6 | Integer32 | read-only | The polling interval, in seconds. |
| I32 alaNtpPeerListReach | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.1.1.7 | Integer32 | read-only | The reachability register of the remote association, in octal format. This number is determined by the NTP algorithm. |
| STR alaNtpPeerListDelay | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.1.1.8 | SnmpAdminString | read-only | The currently estimated delay of this remote association, in seconds. This time is determined by the NTP algorithm. |
| STR alaNtpPeerListOffset | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.1.1.9 | SnmpAdminString | read-only | The currently estimated offset of this remote association, in seconds. This time is determined by the NTP algorithm. |
| STR alaNtpPeerListDispersion | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.1.1.10 | SnmpAdminString | read-only | The currently estimated dispersion of this remote association, in seconds. This time is determined by the NTP algorithm. |
| INT alaNtpPeerListSynced | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.1.1.11 | INTEGER | read-only | Indicates that NTP is synchronized with this entity. |
| STR alaNtpPeerListName | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.1.1.12 | SnmpAdminString | read-only | The DNS name for the peer association, |
| alaNtpPeerShowTable | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.3 | not-accessible | Used to display a brief list of all NTP associations related to this switch (servers, peers, etc.). | |
| alaNtpPeerShowEntry | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.3.1 | not-accessible | Each entry corresponds to one association. | |
| IPt alaNtpPeerShowRemoteAddressType | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.3.1.1 | InetAddressType | not-accessible | The InetAddress type of the synchronization host. InetAddressIPv4 (1) is the only type currently supported. |
| IP alaNtpPeerShowRemoteAddress | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.3.1.2 | InetAddress | not-accessible | The InetAddress of the remote association. |
| IP alaNtpPeerShowRemoteIpAddress | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.3.1.3 | IpAddress | read-only | The IP address of the remote association. |
| IP alaNtpPeerShowLocal | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.3.1.4 | IpAddress | read-only | The local interface address assigned by NTP to the remote associations. |
| STR alaNtpPeerShowHmode | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.3.1.5 | SnmpAdminString | read-only | The host mode of this remote association. |
| STR alaNtpPeerShowPmode | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.3.1.6 | SnmpAdminString | read-only | The peer mode of this remote association. |
| I32 alaNtpPeerShowStratum | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.3.1.7 | Integer32 | read-only | The stratum level of the remote peer. |
| I32 alaNtpPeerShowPrecision | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.3.1.8 | Integer32 | read-only | The advertised precision of this association, which is a number from -4 to -20. |
| INT alaNtpPeerShowLeapIndicator | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.3.1.9 | INTEGER | read-only | The status of leap second insertion for this association. |
| STR alaNtpPeerShowReferenceId | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.3.1.10 | SnmpAdminString | read-only | This is a 32-bit code identifying the peers primary reference source. Normally an IP address. |
| STR alaNtpPeerShowRootDistance | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.3.1.11 | SnmpAdminString | read-only | This is a signed fixed-point number indicating the total roundtrip delay to the primary reference source at the root of the synchronization subnet, in seconds. |
| STR alaNtpPeerShowRootDispersion | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.3.1.12 | SnmpAdminString | read-only | This is a signed fixed-point number indicating the maximum error relative to the primary reference source at the root of the synchronization subnet, in seconds. |
| I32 alaNtpPeerShowPpoll | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.3.1.13 | Integer32 | read-only | The poll time for this association when it is a peer. |
| I32 alaNtpPeerShowHpoll | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.3.1.14 | Integer32 | read-only | The poll time for this association when it is a host. |
| I32 alaNtpPeerShowKeyid | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.3.1.15 | Integer32 | read-only | This is an integer identifying the cryptographic key used to generate the message authentication code. |
| I32 alaNtpPeerShowVersion | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.3.1.16 | Integer32 | read-only | What version of NTP this association is using. |
| I32 alaNtpPeerShowAssociation | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.3.1.17 | Integer32 | read-only | The number of seconds since this NTP entity was associated with the switch. |
| INT alaNtpPeerShowValid | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.3.1.18 | INTEGER | read-only | This is an integer indicating the validity of current NTP system variables. The validity is made false if system variable are changed and a new peer sample under the changed configuration has not been received. |
| I32 alaNtpPeerShowReach | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.3.1.19 | Integer32 | read-only | This is a shift register used to determine the reachability status of this peer. |
| I32 alaNtpPeerShowUnreach | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.3.1.20 | Integer32 | read-only | The number of times this NTP entity was unreachable. |
| I32 alaNtpPeerShowFlash | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.3.1.21 | Integer32 | read-only | This bitmap reveals the state at the last grumble from the peer and are most handy for diagnosing problems. Duplicate packet: 0x0001 Bogus packet: 0x0002 Protocol unsynchronized: 0x0004 Access denied: 0x0008 Authentication failure: 0x0010 Peer clock unsynchronized: 0x0020 Peer stratum out: 0x0040 Root delay/dispersion bounds check: 0x0080 Peer delay dispersion bounds check: 0x0100 Autokey failed: 0x0200 Proventic not confirmed: 0x0400 |
| STR alaNtpPeerShowBroadcastOffset | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.3.1.22 | SnmpAdminString | read-only | The broadcast delay. |
| I32 alaNtpPeerShowTTL | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.3.1.23 | Integer32 | read-only | This field displays the Time-to-Live (TTL) time in seconds and the mode (unicast, multicast, or broadcast) of NTP messages sent to a broadcast address. |
| I32 alaNtpPeerShowTimer | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.3.1.24 | Integer32 | read-only | The time to next poll in seconds. |
| I32 alaNtpPeerShowFlags | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.3.1.25 | Integer32 | read-only | This details which flags have been configured for this peer. Association configured: 0x01 System peer: 0x02 Enabled for burst mode synchronization: 0x04 Reference clock: 0x08 Preferred server: 0x10 Authentable: 0x20 Synchronization candidate: 0x40 Synchronization candidates short-list: 0x80 |
| STR alaNtpPeerShowReferenceTime | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.3.1.26 | SnmpAdminString | read-only | This is the local time, in timestamp format, when the peer clock was last updated. |
| STR alaNtpPeerShowOriginateTime | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.3.1.27 | SnmpAdminString | read-only | This is the local time, in timestamp format, of the peer when its latest NTP message was sent. |
| STR alaNtpPeerShowReceiveTime | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.3.1.28 | SnmpAdminString | read-only | This is the local time, in timestamp format, when the latest NTP message from the peer arrived. |
| STR alaNtpPeerShowTransmitTime | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.3.1.29 | SnmpAdminString | read-only | This is the local time, in timestamp format, at which the last NTP message was sent from this association. |
| STR alaNtpPeerShowOffset | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.3.1.30 | SnmpAdminString | read-only | The currently estimated offset of this remote association, in seconds. |
| STR alaNtpPeerShowDelay | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.3.1.31 | SnmpAdminString | read-only | The currently estimated delay of this remote association, in seconds. |
| STR alaNtpPeerShowDispersion | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.3.1.32 | SnmpAdminString | read-only | The currently estimated dispersion of this remote association, in seconds. |
| STR alaNtpPeerShowName | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.3.1.33 | SnmpAdminString | read-only | The DNS name for the peer association, |
| BIT alaNtpPeerShowStatus | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.3.1.34 | Bits | read-only | Peer selection status: Bits 0 - 7 - Rejected due to high stratum and/or failed sanity checks: 1 - Designated falsticker by the intersection algorithm: 2 - Excess, culled from the end of the candidate list: 3 - Outlyer, discarded by the clustering algorithm: 4 - Candidate, included in the final selection set: 5 - Selected for synchronization; but distance exceeds maximum: 6 - Selected for synchronization: 7 - Selected for synchronization, PPS signal in use: 8 Peer association status: Bits 9 - 12 - Peer association configured: 9 - Peer authentication required: 10 - Last peer message authenticated: 11 - Peer reachable: 12 |
| alaNtpClientListTable | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.4 | not-accessible | Used to display a brief list of all incoming NTP client associations related to this switch. | |
| alaNtpClientListEntry | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.4.1 | not-accessible | Each entry corresponds to one association. | |
| IPt alaNtpClientListAddressType | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.4.1.1 | InetAddressType | not-accessible | The InetAddress type of the incoming client association. InetAddressIPv4 (1) is the only type currently supported. |
| IP alaNtpClientListAddress | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.4.1.2 | InetAddress | not-accessible | The InetAddress of the client. |
| I32 alaNtpClientListVersion | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.4.1.3 | Integer32 | read-only | The NTP version used by the remote host for communication. |
| I32 alaNtpClientKey | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.2.4.1.4 | Integer32 | read-only | The authorization keyid for the remote host. |
| alaNtpStats | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.3 | |||
| alaNtpStatsPeerTable | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.3.2 | not-accessible | Table containing the synchronization host statistics. | |
| alaNtpStatsPeerEntry | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.3.2.1 | not-accessible | Each entry corresponds to a synchronization host. | |
| IPt alaNtpStatsPeerAddressType | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.3.2.1.1 | InetAddressType | not-accessible | The InetAddress type of the synchronization host. InetAddressIPv4 (1) is the only type currently supported. |
| IP alaNtpStatsPeerAddress | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.3.2.1.2 | InetAddress | not-accessible | The InetAddress of the synchronization host. |
| IP alaNtpStatsPeerIpAddress | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.3.2.1.3 | IpAddress | read-only | The IP address of the synchronization host. |
| IP alaNtpStatsPeerLocal | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.3.2.1.4 | IpAddress | read-only | The local interface address assigned by NTP to the remote association. |
| C32 alaNtpStatsPeerLastRcv | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.3.2.1.5 | Counter32 | read-only | The time since the last packet was received. |
| C32 alaNtpStatsPeerNextSend | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.3.2.1.6 | Counter32 | read-only | The time until the next packet is to be sent. |
| C32 alaNtpStatsPeerReachChange | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.3.2.1.7 | Counter32 | read-only | The time that the peer has been reachable. |
| C32 alaNtpStatsPeerPacketsSent | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.3.2.1.8 | Counter32 | read-only | The number of packets that have been sent. |
| C32 alaNtpStatsPeerPacketsRcvd | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.3.2.1.9 | Counter32 | read-only | The number of packets that have been received. |
| C32 alaNtpStatsPeerBadAuth | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.3.2.1.10 | Counter32 | read-only | The number of packets received with bad authentication. |
| C32 alaNtpStatsPeerBogusOrigin | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.3.2.1.11 | Counter32 | read-only | The number of bogus packets. |
| C32 alaNtpStatsPeerDuplicate | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.3.2.1.12 | Counter32 | read-only | The number of duplicated packets received. |
| C32 alaNtpStatsPeerBadDispersion | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.3.2.1.13 | Counter32 | read-only | The number bad dispersions. |
| C32 alaNtpStatsPeerBadRefTime | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.3.2.1.14 | Counter32 | read-only | The number of bad reference times received. |
| C32 alaNtpStatsPeerCandidateOrder | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.3.2.1.15 | Counter32 | read-only | The order of synchronization candidates. |
| I32 alaNtpStatsPeerReset | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.3.2.1.16 | Integer32 | read-write | The number of seconds since the statistics for this peer were last reset. Writing any value will reset the peer statistics. |
| STR alaNtpStatsPeerName | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.3.2.1.17 | SnmpAdminString | read-only | The DNS name for the peer association, |
| I32 alaNtpStatsReset | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.3.5 | Integer32 | read-write | Resets the statistics counters for the following subsystems: 0x01 - all peers 0x02 - i/o 0x04 - system 0x08 - memory 0x10 - timer 0x20 - authentication 0x40 - control |
| alaNtpStatsMonitorTable | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.3.6 | not-accessible | Table containing the association monitoring list. | |
| alaNtpStatsMonitorEntry | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.3.6.1 | not-accessible | Each entry corresponds to a synchronization host. | |
| U32 alaNtpStatsMonitorIndex | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.3.6.1.1 | Unsigned32 | not-accessible | Table index. |
| IP alaNtpStatsMonitorAddress | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.3.6.1.2 | IpAddress | read-only | The IP address of the remote association. |
| I32 alaNtpStatsMonitorPort | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.3.6.1.3 | Integer32 | read-only | The IP port number of the association. |
| IP alaNtpStatsMonitorLocalAddress | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.3.6.1.4 | IpAddress | read-only | The local IP address of the association. |
| C32 alaNtpStatsMonitorCount | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.3.6.1.5 | Counter32 | read-only | The number of NTP packets received from this association. |
| STR alaNtpStatsMonitorMode | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.3.6.1.6 | SnmpAdminString | read-only | The mode the NTP association uses in relation to the switch. |
| I32 alaNtpStatsMonitorVersion | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.3.6.1.7 | Integer32 | read-only | The version of NTP the association is using. |
| C32 alaNtpStatsMonitorDrop | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.3.6.1.8 | Counter32 | read-only | The number of NTP packets received from this association that were dropped. |
| C32 alaNtpStatsMonitorLast | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.3.6.1.9 | Counter32 | read-only | The number of seconds since the last NTP message has been received from this association. |
| C32 alaNtpStatsMonitorFirst | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.3.6.1.10 | Counter32 | read-only | The number of seconds since the first NTP message has been received from this association. |
| STR alaNtpStatsMonitorName | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.3.6.1.11 | SnmpAdminString | read-only | The DNS name for the peer association, |
| alaNtpStatsStat | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.4 | |||
| C32 alaNtpStatsStatUptimeEx | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.4.1 | Counter32 | read-only | The number of seconds the local NTP server has been associated with the switch. |
| C32 alaNtpStatsStatReset | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.4.2 | Counter32 | read-only | The number of seconds since the last time the local NTP server has been restarted. |
| C32 alaNtpStatsStatBadStratum | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.4.3 | Counter32 | read-only | The number of NTP packets received that had a corrupted stratum bit in the data of the packet. |
| C32 alaNtpStatsStatOldVersion | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.4.4 | Counter32 | read-only | The number of NTP packets received that were of an older version of NTP (either version 1 or 2). |
| C32 alaNtpStatsStatNewVersion | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.4.5 | Counter32 | read-only | The number of NTP packets received that were version 3 of NTP. |
| C32 alaNtpStatsStatUnknownVersion | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.4.6 | Counter32 | read-only | The number of NTP packets received that the version was unknown (most likely due to packet corruption). |
| C32 alaNtpStatsStatBadLength | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.4.7 | Counter32 | read-only | The number of NTP packets received that did not fit the NTP packet structure (most likely due to packet corruption). |
| C32 alaNtpStatsStatProcessed | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.4.8 | Counter32 | read-only | The total number of NTP packets processed. |
| C32 alaNtpStatsStatBadAuth | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.4.9 | Counter32 | read-only | The number of NTP packets rejected because they did not meet authentication standards. |
| C32 alaNtpStatsStatLimitRejects | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.4.10 | Counter32 | read-only | The number of NTP packets rejected because they did not meet authentication standards. |
| alaNtpStatsLoop | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.5 | |||
| STR alaNtpStatsLoopOffset | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.5.1 | SnmpAdminString | read-only | The currently estimated offset of this remote association, in seconds. This counter indicates the offset of the peer clock relative to the local clock. |
| STR alaNtpStatsLoopFrequency | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.5.2 | SnmpAdminString | read-only | A number determining the local clocks frequency in relation to a reference clocks Pulse per Second (PPS). If the clock is running in perfect synchronization, this number should be 1. Otherwise, it will be slightly lower or higher in order to compensate for the time discrepancy between the reference clock and the local clock. |
| I32 alaNtpStatsLoopPollAdjust | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.5.3 | Integer32 | read-only | Determines the peer polling time. |
| C32 alaNtpStatsLoopWatchdog | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.5.4 | Counter32 | read-only | Makes sure that NTP timer continues to run. |
| alaNtpStatsIo | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.6 | |||
| C32 alaNtpStatsIoReset | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.6.1 | Counter32 | read-only | The number of seconds since the last restart of NTP. |
| C32 alaNtpStatsIoRcvBuffers | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.6.2 | Counter32 | read-only | The number of switch receive buffers currently being used by this NTP entity. |
| C32 alaNtpStatsIoFreeRcvBuffers | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.6.3 | Counter32 | read-only | The number of free receive buffers. |
| C32 alaNtpStatsIoUsedRcvBuffers | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.6.4 | Counter32 | read-only | The number of receive buffers currently being used. |
| C32 alaNtpStatsIoRefills | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.6.5 | Counter32 | read-only | The number of times we added packets. |
| C32 alaNtpStatsIoDroppedPackets | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.6.6 | Counter32 | read-only | The number of packets dropped. |
| C32 alaNtpStatsIoIgnoredPackets | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.6.7 | Counter32 | read-only | The number of packets ignored. |
| C32 alaNtpStatsIoRcvPackets | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.6.8 | Counter32 | read-only | The total number of NTP packets received by the switch. |
| C32 alaNtpStatsIoSentPackets | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.6.9 | Counter32 | read-only | The total number of NTP packets sent by the switch. |
| C32 alaNtpStatsIoNotSentPackets | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.6.10 | Counter32 | read-only | The number of NTP packets generated but not sent due to restrictions. |
| C32 alaNtpStatsIoInterrupts | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.6.11 | Counter32 | read-only | The number of times NTP information was interrupted in the process of transmitting or receiving. |
| C32 alaNtpStatsIoInterruptsRcv | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.6.12 | Counter32 | read-only | The number of packets received by the interrupt handler. |
| alaNtpAccess | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.7 | |||
| alaNtpAccessKeyIdTable | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.7.1 | not-accessible | Table containing the trusted keys. | |
| alaNtpAccessKeyIdEntry | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.7.1.1 | not-accessible | Entry of a trusted key. | |
| I32 alaNtpAccessKeyIdKeyId | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.7.1.1.1 | Integer32 | not-accessible | Keyid of the key in the key file. |
| INT alaNtpAccessKeyIdTrust | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.7.1.1.2 | INTEGER | read-write | The current state of trust of the table entry. |
| alaNtpAccessRestrictedTable | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.7.2 | not-accessible | Table containing the restricted addresses. | |
| alaNtpAccessRestrictedEntry | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.7.2.1 | not-accessible | Entry of a restricted address. | |
| IP alaNtpAccessRestrictedIpAddress | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.7.2.1.1 | IpAddress | not-accessible | IP address to restrict. |
| IP alaNtpAccessRestrictedMask | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.7.2.1.2 | IpAddress | not-accessible | IP mask to restrict. |
| I32 alaNtpAccessRestrictedRestrictions | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.7.2.1.3 | Integer32 | read-create | A mask indicating the restrictions to apply to the entry. 0x0001 - ignore, Ignore all packets from hosts. Can't use this on default (0.0.0.0). 0x0002 - noserve, Ignore NTP packets other than information queries and config-uration requests. 0x0004 - notrust, Treat these hosts normally in other respects, but never use them as synchronization sources. 0x0008 - noquery, Ignore all NTP information queries and configuration requests from the source. 0x0010 - nomodify, Ignore all NTP information queries and configuration requests that attempt to modify the state of the server. 0x0020 - nopeer, Provide stateless time service to polling hosts, but do not allocate peer memory resources to these hosts even if they otherwise might be considered useful as future synchronization partners. 0x0040 - notrap, Decline to provide control message trap service to matching hosts. 0x0080 - lowpriotrap, Declare traps set by matching hosts to be low priority. 0x0100 - limited, These hosts are subject to a limitation of the number of clients from the same net. 0x0200 - version. Serves only current version. 0x0400 - demobilize. A demobilization packet (kod) packet is sent. |
| C32 alaNtpAccessRestrictedCount | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.7.2.1.4 | Counter32 | read-only | Number of packets matched. |
| ROW alaNtpAccessRestrictedRowStatus | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.7.2.1.5 | RowStatus | read-create | Used in accordance to installation and removal conventions for conceptual rows. The RowStatus values that are supported are the following: active(1) - The row is active and valid. createAndGo(4) - The row will be created and activated. destroy(6) - The row will be destroyed. |
| INT alaNtpAccessRereadKeyFile | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.7.3 | INTEGER | read-write | Reloads the keyfile containing all currently existing keys into the alaNtpAccessKeyIdTable in the switch's memory. Reading this object will yield one of the three following values: inProgress(2), successful(3), failed(4) A value of inProgress means that table reload procedure is inProgress and not yet complete. A sucessful reply means the last attempted keyfile load completed successfully. A failed response indicates the last attempt to reload failed. Writing a value of 1 to this object initiates a reload of the table. |
| alaNtpLocalInfo | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.8 | |||
| IP alaNtpInfoPeer | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.8.1 | IpAddress | read-only | The IP address of the remote association. |
| STR alaNtpInfoMode | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.8.2 | SnmpAdminString | read-only | The peer mode of this remote association. |
| INT alaNtpInfoLeapIndicator | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.8.3 | INTEGER | read-only | The status of leap second insertion for this association. |
| I32 alaNtpInfoStratum | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.8.4 | Integer32 | read-only | The stratum level of the remote peer. If this number is 16, the remote peer has not been synchronized. |
| I32 alaNtpInfoPrecision | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.8.5 | Integer32 | read-only | The advertised precision of the switch. It will be a number between -4 and -20. |
| STR alaNtpInfoDistance | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.8.6 | SnmpAdminString | read-only | This is a signed fixed-point number indicating the total roundtrip delay to the primary reference source at the root of the synchronization subnet, in seconds. |
| STR alaNtpInfoDispersion | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.8.7 | SnmpAdminString | read-only | This is a signed fixed-point number indicating the maximum error relative to the primary reference source at the root of the synchronization subnet, in seconds. |
| STR alaNtpInfoReferenceId | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.8.8 | SnmpAdminString | read-only | This is a 32-bit code identifying the particular reference clock. Can be an IP address. |
| STR alaNtpInfoReferenceTime | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.8.9 | SnmpAdminString | read-only | This is the local time at which the local clock was last set or corrected. |
| STR alaNtpInfoFrequency | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.8.10 | SnmpAdminString | read-only | A number determining the local clocks frequency in relation to a reference clock's Pulse per Second (PPS). If the clock is running in perfect synchronization, this number should be 1. Otherwise, it will be slightly lower or higher in order to compensate for the time difference. |
| STR alaNtpInfoStability | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.8.11 | SnmpAdminString | read-only | The stability of the clock in relation to a reference clock's Pulse per Second (PPS). |
| STR alaNtpInfoBroadcastDelay | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.8.12 | SnmpAdminString | read-only | The broadcast delay, in seconds, of this association. |
| STR alaNtpInfoAuthDelay | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.8.13 | SnmpAdminString | read-only | The authentication delay, in seconds, of this association. |
| INT ntpClientConfig | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.9 | INTEGER | read-write | The Agent Config Information 1 -- Default(Loopback0 or closest IP) 2 -- Non Loopback0 3 -- Interface IP Specified by User |
| IP ntpClientIP | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.10 | IpAddress | read-write | The interface IP Address to be used in NTP Packets for Source IP field. |
| INT alaNtpSrcIpConfig | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.11 | INTEGER | read-write | The Agent Config Information 1 -- Default(Loopback0 or closest IP) 2 -- Non Loopback0 3 -- Interface IP Specified by User |
| IP alaNtpSrcIp | 1.3.6.1.4.1.6486.801.1.2.1.26.1.1.12 | IpAddress | read-write | The interface IP Address to be used in NTP Packets for Source IP field. |
| alaIND1NtpMIBConformance | 1.3.6.1.4.1.6486.801.1.2.1.26.1.2 | Branch For Ntp Subsystem Managed Objects. | ||
| alaIND1NtpMIBGroups | 1.3.6.1.4.1.6486.801.1.2.1.26.1.2.1 | Branch For Ntp Subsystem Managed Objects. | ||
| alaNtpConfigGroup | 1.3.6.1.4.1.6486.801.1.2.1.26.1.2.1.1 | Collection of NTP configuration objects. | ||
| alaNtpInfoGroup | 1.3.6.1.4.1.6486.801.1.2.1.26.1.2.1.2 | Collection of NTP peer information objects. | ||
| alaNtpStatsGroup | 1.3.6.1.4.1.6486.801.1.2.1.26.1.2.1.3 | Collection of NTP peer information objects. | ||
| alaNtpStatsStatGroup | 1.3.6.1.4.1.6486.801.1.2.1.26.1.2.1.4 | Collection of NTP statistic objects. | ||
| alaNtpStatsLoopGroup | 1.3.6.1.4.1.6486.801.1.2.1.26.1.2.1.5 | Collection of NTP clocking objects. | ||
| alaNtpStatsIoGroup | 1.3.6.1.4.1.6486.801.1.2.1.26.1.2.1.6 | Collection of NTP send and receive statistics objects. | ||
| alaNtpAccessGroup | 1.3.6.1.4.1.6486.801.1.2.1.26.1.2.1.7 | Collection of NTP authentication control objects. | ||
| alaNtpLocalInfoGroup | 1.3.6.1.4.1.6486.801.1.2.1.26.1.2.1.8 | Collection of NTP local clock information objects. | ||
| alaNtpEventsGroup | 1.3.6.1.4.1.6486.801.1.2.1.26.1.2.1.9 | Notify the management entity on reaching the maximum allowable NTP client and peer associations. | ||
| alaNtpSrcIpGroup | 1.3.6.1.4.1.6486.801.1.2.1.26.1.2.1.10 | Collection of NTP source IP information objects. | ||
| alaNtpStatsMonitorGroup | 1.3.6.1.4.1.6486.801.1.2.1.26.1.2.1.11 | Each entry corresponds to a synchronization host. | ||
| alaIND1NtpMIBCompliances | 1.3.6.1.4.1.6486.801.1.2.1.26.1.2.2 | Branch For Ntp Subsystem Managed Objects. | ||
| alaIND1NtpMonitorMIBCompliance | 1.3.6.1.4.1.6486.801.1.2.1.26.1.2.2.1 | Compliance statement for Health Monitoring. |
RFC description
Manages NTP (Network Time Protocol) configuration and status on Alcatel-Lucent enterprise switching platforms.
Start monitoring Alcatel-Lucent Enterprise OmniSwitch switches with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.