AIRESPACE-WIRELESS-MIB

All MIBs › AIRESPACE-WIRELESS-MIB

Organization: Airespace, Inc.

Last Updated: 2011-09-27

Category: Wireless and WLAN

Description: Manages wireless LAN controller configuration, access point associations, and client sessions on Airespace (Cisco) WLAN systems.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is AIRESPACE-WIRELESS-MIB?

AIRESPACE-WIRELESS-MIB is a private MIB originating from Airespace (acquired by Cisco, forming the basis of Cisco's Unified Wireless Network / WLC product line) for centralized WLAN controllers that terminate LWAPP tunnels from lightweight access points. It exposes a broad range of data: 802.11 SSID/ESS configuration, access point association and management, client sessions, AAA settings, mobility groups, IPsec, radio resource management, and global 802.11 parameters. Much of it is configuration-oriented, but objects like bsnDot11EssAdminStatus reflect the operational/software status of each wireless network, and radio resource management data supports detecting RF-level problems on associated access points, both relevant to overall WLAN service health. It builds on IEEE 802.11 standard concepts and the LWAPP tunnel architecture (precursor to CAPWAP, RFC 5415) between controller and access points. It is deployed on Airespace/Cisco Wireless LAN Controllers (the WLC 2000/4400/5500 family and successors) in enterprise campus Wi-Fi deployments. This is a heavily searched Cisco (Airespace heritage) MIB, since airespace-wireless-mib is the standard reference for monitoring Cisco Airespace/WLC wireless controller status via SNMP.

IPNetwork Monitor allows you to monitor SNMP objects defined in AIRESPACE-WIRELESS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Airespace / Cisco Wireless LAN Controllers (WLC)
Cisco Unified Wireless Network lightweight/LWAPP access points

Monitoring Examples

An admin polls bsnDot11EssTable/bsnDot11EssEntry (indexed by bsnDot11EssIndex) to check bsnDot11EssSsid, bsnDot11EssAdminStatus, and bsnDot11EssSecurityAuthType, confirming an SSID is administratively up and using the intended authentication method, which catches an accidental SSID shutdown or a security downgrade. bsnDot11EssSessionTimeout and bsnDot11EssMacFiltering reveal session and access-control policy in force, while bsnDot11EssStaticWEPSecurity, bsnDot11EssStaticWEPDefaultKey, and bsnDot11EssStaticWEPKeyIndex let an operator verify legacy WEP configuration consistency across controllers during a migration or audit.

What Can Be Monitored

SSID/ESS configuration and admin status
802.11 security/authentication type
WEP key configuration
session timeout policy
MAC filtering status
AP association state

Imported Objects

From AIRESPACE-REF-MIB

airespace

MODULE-IDENTITY

From INET-ADDRESS-MIB

InetAddress
InetAddressType

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Counter64
Gauge32
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
TimeTicks
Unsigned32

From SNMPv2-TC

DisplayString
MacAddress
RowStatus
TEXTUAL-CONVENTION
TimeInterval
TruthValue

How to Use in IPNetwork Monitor

Example using bsnTotalHandoffRequests OID:

Select a Cisco (Airespace) Wireless LAN Controller (legacy) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type bsnTotalHandoffRequests into the Find box to locate it in the OID tree, then select it and click OK. It reports the total handoff requests. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
bsnWireless	1.3.6.1.4.1.14179.2			This MIB is intended to be implemented on all those devices operating as Central Controllers (CC) that terminate the Light Weight Access Point Protocol tunnel from Light-weight LWAPP Access Points. This MIB provides configuration and status information for 802.11 Access Points, LAN configuration, AAA, Mobility, IpSec, Radio Rescouce Management and 802.11 global parameters. The relationship between controller and the LWAPP APs can be depicted as follows: +......+ +......+ +......+ +......+ + + + + + + + + + CC + + CC + + CC + + CC + + + + + + + + + +......+ +......+ +......+ +......+ .. . . . .. . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + AP + + AP + + AP + + AP + + AP + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + MN + + MN + + MN + + MN + + MN + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY Access Point ( AP ) An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends it to the controller to which it is logically connected. Basic Service Set Identifier (BSSID) The identifier for the service set comprising of all the 802.11 stations under the control of one coordinating Access Point. This identifier happens to be the MAC address of the dot11 radio interface of the Access Point. The wireless clients that associate with the Access Point get the wired uplink through this particular dot11 interface. Central Controller ( CC ) The central entity that terminates the LWAPP protocol tunnel from the LWAPP APs. Throughout this MIB, this entity also referred to as 'controller'. Light Weight Access Point Protocol ( LWAPP ) This is a generic protocol that defines the communication between the Access Points and the Central Controller. Mobile Node ( MN ) A roaming 802.11 wireless device in a wireless network associated with an access point. Station Management (SMT) This term refers to the internal management of the 802.11 protocol operations by the AP to work cooperatively with the other APs and 802.11 devices in the network. REFERENCE [1] Part 11 Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications. [2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol.
bsnEss	1.3.6.1.4.1.14179.2.1
bsnDot11EssTable	1.3.6.1.4.1.14179.2.1.1		not-accessible	Ess(WLAN) Configuration Table indexed by bsnDot11EssIndex. Maximum of 17 WLANs can be created on Airespace Switch. bsnDot11EssIndex of 17 is reserved for WLAN for Third Party APs(non-Airespace APs).
bsnDot11EssEntry	1.3.6.1.4.1.14179.2.1.1.1		not-accessible	An entry in bsnDot11EssTable
U32 bsnDot11EssIndex	1.3.6.1.4.1.14179.2.1.1.1.1	Unsigned32	read-create	Index of the Ess(WLAN) within Airespace Switch. Airespace Switch supports 517 ESS(Wlans) so index will be from 1 to 517. 517 is to be used for ESS(WLAN) created for support of Third Party APs(non-Airespace APs)
STR bsnDot11EssSsid	1.3.6.1.4.1.14179.2.1.1.1.2	DisplayString	read-create	SSID assigned to ESS(WLAN)
U32 bsnDot11EssSessionTimeout	1.3.6.1.4.1.14179.2.1.1.1.4	Unsigned32	read-create	Maximum time of a Mobile Station session. Value of 0 means infinite time(no timeout set).
INT bsnDot11EssMacFiltering	1.3.6.1.4.1.14179.2.1.1.1.5	INTEGER	read-create	A type of security policy for Mobile Stations (Clients). Select to filter clients by MAC address. By selecting this Security, you need to create MacFilters in bsnUsersTable or have MacFilters configured on Radius Servers specified in bsnRadiusAuthenticationTable
INT bsnDot11EssAdminStatus	1.3.6.1.4.1.14179.2.1.1.1.6	INTEGER	read-create	Administrative Status of ESS(WLAN). By disabling an ESS the corresponding SSID is no longer broadcasted in AP beacons.
INT bsnDot11EssSecurityAuthType	1.3.6.1.4.1.14179.2.1.1.1.7	INTEGER	read-only	Type of 802.11 Authentication.
INT bsnDot11EssStaticWEPSecurity	1.3.6.1.4.1.14179.2.1.1.1.8	INTEGER	read-create	Status of Static WEP Security policy. If enabled, WEP Encryption WEP Default Key, Key Index and Key Format should also be specified.
INT bsnDot11EssStaticWEPEncryptionType	1.3.6.1.4.1.14179.2.1.1.1.9	INTEGER	read-create	Type of Static WEP Encryption. Length of key specified in Default Key depends on this attribute.
WEP bsnDot11EssStaticWEPDefaultKey	1.3.6.1.4.1.14179.2.1.1.1.10	WEPKeytype	read-create	Static WEP Default Key. For wep104 encryption either 26 bit hex key or 13 bit ascii key should be specified. For wep40 encryption 10 bit hex key or 5 bit ascii key should be specified. For wep128 encryption 32 bit hex key or 16 bit ascii key should be specified.
INT bsnDot11EssStaticWEPKeyIndex	1.3.6.1.4.1.14179.2.1.1.1.11	INTEGER	read-create	According to 802.11 standard 4 keys are supported. So 802.11 Mobile Stations(Client) can have upto 4 keys. This index is for informing Mobile Station which key it should use for Static WEP Authentication
INT bsnDot11EssStaticWEPKeyFormat	1.3.6.1.4.1.14179.2.1.1.1.12	INTEGER	read-create	This is not persistant.Reading this attribute will always return default. The format of the key specified in Airespace switch keeps record of the Index.
INT bsnDot11Ess8021xSecurity	1.3.6.1.4.1.14179.2.1.1.1.13	INTEGER	read-create	Status of 802.1X security policy.
INT bsnDot11Ess8021xEncryptionType	1.3.6.1.4.1.14179.2.1.1.1.14	INTEGER	read-create	Type of 802.1X Encryption. This applies if bsnDot11Ess8021xSecurity is in enabled state.
INT bsnDot11EssWPASecurity	1.3.6.1.4.1.14179.2.1.1.1.16	INTEGER	read-create	Status of WPA security policy. This has been deprecated for cLWSecDot11EssCckmTable.
INT bsnDot11EssWPAEncryptionType	1.3.6.1.4.1.14179.2.1.1.1.17	INTEGER	read-create	Type of WPA Encryption. This applies when bsnDot11EssWPASecurity is in enable state. This has been deprecated for cLWSecDot11EssCckmTable.
INT bsnDot11EssIpsecSecurity	1.3.6.1.4.1.14179.2.1.1.1.18	INTEGER	read-create	Status of IpSec (VPN) security policy. Note that this cannot be applied with Web security policy.
INT bsnDot11EssVpnEncrTransform	1.3.6.1.4.1.14179.2.1.1.1.19	INTEGER	read-create	The Encryption algorithm employed by this Vpn(IpSec) Encryption. This applies only when bsnDot11EssIpsecSecurity is in enable state.
INT bsnDot11EssVpnAuthTransform	1.3.6.1.4.1.14179.2.1.1.1.20	INTEGER	read-create	The Hash algorithm employed by the Vpn Encrpytion. This applies only when bsnDot11EssIpsecSecurity is in enable state.
INT bsnDot11EssVpnIkeAuthMode	1.3.6.1.4.1.14179.2.1.1.1.21	INTEGER	read-create	The authentication type of the SA. It could be a certificate or a pre-shared key or xauthEnablePsk. This applies only when bsnDot11EssIpsecSecurity is in enable state.
OCT bsnDot11EssVpnSharedKey	1.3.6.1.4.1.14179.2.1.1.1.22	OCTET STRING	read-create	VPN Shared Key. This applies only when bsnDot11EssVpnSharedKey is in enable state and bsnDot11EssVpnIkeAuthMode is xauthEnablePsk or presharedKey.
U32 bsnDot11EssVpnSharedKeySize	1.3.6.1.4.1.14179.2.1.1.1.23	Unsigned32	read-only	VPN Shared Key size. This applies only when bsnDot11EssVpnSharedKey is in enable state and bsnDot11EssVpnIkeAuthMode is xauthEnablePsk or presharedKey.
INT bsnDot11EssVpnIkePhase1Mode	1.3.6.1.4.1.14179.2.1.1.1.24	INTEGER	read-create	VPN IKE Phase 1 Mode type as per the IpSec standards. This applies only when bsnDot11EssIpsecSecurity is in enable state.
I32 bsnDot11EssVpnIkeLifetime	1.3.6.1.4.1.14179.2.1.1.1.25	Integer32	read-create	Vpn IKE's Lifetime. This applies only when bsnDot11EssIpsecSecurity is in enable state.
INT bsnDot11EssVpnIkeDHGroup	1.3.6.1.4.1.14179.2.1.1.1.26	INTEGER	read-create	IKE's Diffie-Hellman Group. This applies only when bsnDot11EssIpsecSecurity is in enable state.
INT bsnDot11EssIpsecPassthruSecurity	1.3.6.1.4.1.14179.2.1.1.1.27	INTEGER	read-create	Status of IpSec Passthru security policy.
IP bsnDot11EssVpnPassthruGateway	1.3.6.1.4.1.14179.2.1.1.1.28	IpAddress	read-create	Ip address of VpnPassthru Gateway. This applies only when bsnDot11EssIpsecPassthruSecurity is in enable state.
INT bsnDot11EssWebSecurity	1.3.6.1.4.1.14179.2.1.1.1.29	INTEGER	read-create	Status of Web security policy. Note this policy cannot be applied with IpSec security policy.
INT bsnDot11EssRadioPolicy	1.3.6.1.4.1.14179.2.1.1.1.30	INTEGER	read-create	Radio Policy for a WLAN. It can either be All where it will be applicable to ALL types of protocols or it can be set to apply to combinations of 802.11a, 802.11b, 802.11g.
INT bsnDot11EssQualityOfService	1.3.6.1.4.1.14179.2.1.1.1.31	INTEGER	read-create	Quality of Service for a WLAN.Services such as VoIP should be set to Gold while non-discriminating services such as messaging can be set to Bronze.
INT bsnDot11EssDhcpRequired	1.3.6.1.4.1.14179.2.1.1.1.32	INTEGER	read-create	DHCP required for all clients on this WLAN
IP bsnDot11EssDhcpServerIpAddress	1.3.6.1.4.1.14179.2.1.1.1.33	IpAddress	read-create	IP Address of the DHCP Server. Make it 0.0.0.0 to disable DHCP Relay. Any value other than 0.0.0.0, it will be assumed that DHCP Relay is turned on.
INT bsnDot11EssVpnContivityMode	1.3.6.1.4.1.14179.2.1.1.1.34	INTEGER	read-create	Specifies if contivity mode for the IpSec is enabled. If enabled, user needs to specify the Quote of the Day Server's IPAddress in bsnDot11EssVpnQotdServerAddress.
IP bsnDot11EssVpnQotdServerAddress	1.3.6.1.4.1.14179.2.1.1.1.35	IpAddress	read-create	IP Address of the Quote of the Day Server.
I32 bsnDot11EssBlacklistTimeout	1.3.6.1.4.1.14179.2.1.1.1.37	Integer32	read-create	Set the timeout for blacklisted Mobile Stations after which the mobile station will be automatically de-authenticated. Mobile Station are blacklisted by MAC address and their status can be obtained from bsnMobileStationStatus. A timeout setting of 0 indicates no blacklist timeout is set and administrative control (bsnMobileStationDeleteAction ) is required to deauthenticate the station.
C32 bsnDot11EssNumberOfMobileStations	1.3.6.1.4.1.14179.2.1.1.1.38	Counter32	read-only	No of Mobile Stations currently associated with the WLAN.
INT bsnDot11EssWebPassthru	1.3.6.1.4.1.14179.2.1.1.1.39	INTEGER	read-create	For switches with version before 2.0: This is applicable only when the Web Security Type is enabled. When this attribute is enabled, it allows a client's NetBIOS packets to go through the switch before web auth is completed. (This is obsolete for Switch versions 2.0 to 2.2). For switch verions 3.0 and above: This is reintroduced as the web policy where the client is connected through the web without authentication that is there is no username/password input required. Moreover, if the bsnDot11EssWebPassthroughEmail is enabled, the user will be asked to enter an email address.
INT bsnDot11EssCraniteSecurity	1.3.6.1.4.1.14179.2.1.1.1.40	INTEGER	read-create	Status of Cranite Passthrough Security policy. If enabled, no other security can be enabled.
INT bsnDot11EssBlacklistingCapability	1.3.6.1.4.1.14179.2.1.1.1.41	INTEGER	read-create	This is the flag that can enable or disable the client backlisting feature for a WLAN. If enabled, the clients can be blacklisted by the Switch in case of repetitive auth failure and other reasons like it. If disabled, the clients cannot be blacklisted by the switch. The blacklist timeout value will only be effective if this feature is turned on.
STR bsnDot11EssInterfaceName	1.3.6.1.4.1.14179.2.1.1.1.42	DisplayString	read-create	Name of the interface used by this WLAN. By default it is set to be the management interface.
STR bsnDot11EssAclName	1.3.6.1.4.1.14179.2.1.1.1.43	DisplayString	read-create	Name of ACL for the WLAN. This is applicable only when Web Authentication is enabled as a security. An empty string value indicates that no ACL has been set (which is a valid option)
INT bsnDot11EssAAAOverride	1.3.6.1.4.1.14179.2.1.1.1.44	INTEGER	read-create	Enable or Disable AAA override for the global WLAN parameters.
INT bsnDot11EssWPAAuthKeyMgmtMode	1.3.6.1.4.1.14179.2.1.1.1.45	INTEGER	read-create	Enable or Disable WPA Pre-shared Key Mode. If enabled, a preshared key should be set for WPA authentication. This has been deprecated for cLWSecDot11EssCckmTable.
OCT bsnDot11EssWPAAuthPresharedKey	1.3.6.1.4.1.14179.2.1.1.1.46	OCTET STRING	read-create	WPA Authentication Preshared Key. This applies only when bsnDot11EssWPAAuthKeyMgmtMode is in enable state. This has been deprecated for cLWSecDot11EssCckmTable.
INT bsnDot11EssFortressSecurity	1.3.6.1.4.1.14179.2.1.1.1.47	INTEGER	read-create	Status of Fortress Passthrough Security policy. If enabled, no other security can be enabled.
INT bsnDot11EssWepAllowSharedKeyAuth	1.3.6.1.4.1.14179.2.1.1.1.48	INTEGER	read-create	Enable this flag to allow Shared Key Authentication when Static WEP is enabled.
INT bsnDot11EssL2tpSecurity	1.3.6.1.4.1.14179.2.1.1.1.49	INTEGER	read-create	Status of L2TP security policy. Note that this cannot be applied with Web security policy, Cranite or Fortress policy.
OCT bsnDot11EssWPAAuthPresharedKeyHex	1.3.6.1.4.1.14179.2.1.1.1.50	OCTET STRING	read-create	WPA Authentication Preshared Key in the hex format. This applies only when bsnDot11EssWPAAuthKeyMgmtMode is in enable state. This has been deprecated for cLWSecDot11EssCckmTable.
INT bsnDot11EssBroadcastSsid	1.3.6.1.4.1.14179.2.1.1.1.51	INTEGER	read-create	This attribute when enabled allows the switch to broadcast this SSID.
INT bsnDot11EssExternalPolicyValidation	1.3.6.1.4.1.14179.2.1.1.1.52	INTEGER	read-create	This attribute specifies if external policy servers will be used for validation. If no servers are configured in bsnExternalPolicyServerTable then it cannot be enabled.
INT bsnDot11EssRSNSecurity	1.3.6.1.4.1.14179.2.1.1.1.53	INTEGER	read-create	This attribute specifies status of RSN Security Policy. This has been deprecated for cLWSecDot11EssCckmTable.
INT bsnDot11EssRSNWPACompatibilityMode	1.3.6.1.4.1.14179.2.1.1.1.54	INTEGER	read-create	This attribute specifies RSN security's compatibility mode with WPA. This has been deprecated for cLWSecDot11EssCckmTable.
INT bsnDot11EssRSNAllowTKIPClients	1.3.6.1.4.1.14179.2.1.1.1.55	INTEGER	read-create	This attribute specifies whether TKIP clients are allowed by RSN Policy. This has been deprecated for cLWSecDot11EssCckmTable.
INT bsnDot11EssRSNAuthKeyMgmtMode	1.3.6.1.4.1.14179.2.1.1.1.56	INTEGER	read-create	This attribute specifies whether Preshared key is used or not. If used user should specify a key between 8 and 63 characters in bsnDot11EssRSNAuthPresharedKey attribute. This has been deprecated for cLWSecDot11EssCckmTable.
OCT bsnDot11EssRSNAuthPresharedKey	1.3.6.1.4.1.14179.2.1.1.1.57	OCTET STRING	read-create	RSN Authentication Preshared Key. This applies only when bsnDot11EssRSNAuthKeyMgmtMode is in enable state. This has been deprecated for cLWSecDot11EssCckmTable.
OCT bsnDot11EssRSNAuthPresharedKeyHex	1.3.6.1.4.1.14179.2.1.1.1.58	OCTET STRING	read-create	RSN Authentication Preshared Key in the hex format. This applies only when bsnDot11EssWPAAuthKeyMgmtMode is in enable state. This has been deprecated for cLWSecDot11EssCckmTable.
INT bsnDot11EssIPv6Bridging	1.3.6.1.4.1.14179.2.1.1.1.59	INTEGER	read-create	When enabled, IPv6 bridging is applied on the packets.
ROW bsnDot11EssRowStatus	1.3.6.1.4.1.14179.2.1.1.1.60	RowStatus	read-create	A row status type for the bsnDot11EssEntry
INT bsnDot11EssWmePolicySetting	1.3.6.1.4.1.14179.2.1.1.1.61	INTEGER	read-create	When enabled, WME Policy is applied on the packets.
INT bsnDot11Ess80211ePolicySetting	1.3.6.1.4.1.14179.2.1.1.1.62	INTEGER	read-create	When enabled, 802.11e Policy is applied on the packets.
INT bsnDot11EssWebPassthroughEmail	1.3.6.1.4.1.14179.2.1.1.1.63	INTEGER	read-create	When enabled, along with the bsnDot11EssWebPassthru attribute, the client is allowed to connect by entering his/her email address on the web connection page. There is no further authentication required.
INT bsnDot11Ess7920PhoneSupport	1.3.6.1.4.1.14179.2.1.1.1.64	INTEGER	read-create	When client cac limit is enabled, the 7920 Phones with old software where the Call Admission Control (CAC) Limit is Specified on the client will be supported on the WLAN. The support for clientCacLimit (by setting to value 1 or 3) cannot be enabled when the bsnDot11EssWmePolicySetting is set to allowed or required. When ap cac limit is enabled, the 7920 Phones with new software where the Call Admission Control (CAC) Limit is advertised by the AP, will be supported on the WLAN.
STR bsnDot11EssRadiusAuthPrimaryServer	1.3.6.1.4.1.14179.2.1.1.1.95	DisplayString	read-create	Primary Radius Authentication Server for this wlan.
STR bsnDot11EssRadiusAuthSecondaryServer	1.3.6.1.4.1.14179.2.1.1.1.96	DisplayString	read-create	Secondary Radius Authentication Server for this wlan.
STR bsnDot11EssRadiusAuthTertiaryServer	1.3.6.1.4.1.14179.2.1.1.1.97	DisplayString	read-create	Tertiary Radius Authentication Server for this wlan.
STR bsnDot11EssRadiusAcctPrimaryServer	1.3.6.1.4.1.14179.2.1.1.1.98	DisplayString	read-create	Primary Radius Accounting Server for this wlan.
STR bsnDot11EssRadiusAcctSecondaryServer	1.3.6.1.4.1.14179.2.1.1.1.99	DisplayString	read-create	Secondary Radius Accounting Server for this wlan.
STR bsnDot11EssRadiusAcctTertiaryServer	1.3.6.1.4.1.14179.2.1.1.1.100	DisplayString	read-create	Tertiary Radius Accounting Server for this wlan.
bsnMobileStationTable	1.3.6.1.4.1.14179.2.1.4		not-accessible	Mobile Station Table indexed by bsnMobileStationMacAddress. (Mobile Station is better referred to as Client in the current releases.)
bsnMobileStationEntry	1.3.6.1.4.1.14179.2.1.4.1		not-accessible	An entry in bsnMobileStationTable.
MAC bsnMobileStationMacAddress	1.3.6.1.4.1.14179.2.1.4.1.1	MacAddress	read-only	802.11 MAC Address of the Mobile Station.
IP bsnMobileStationIpAddress	1.3.6.1.4.1.14179.2.1.4.1.2	IpAddress	read-only	IP Address of the Mobile Station
STR bsnMobileStationUserName	1.3.6.1.4.1.14179.2.1.4.1.3	DisplayString	read-only	User Name,if any, of the Mobile Station. This would be non empty in case of Web Authentication and IPSec.
MAC bsnMobileStationAPMacAddr	1.3.6.1.4.1.14179.2.1.4.1.4	MacAddress	read-only	802.11 Mac Address of the AP to which the Mobile Station is associated.
INT bsnMobileStationAPIfSlotId	1.3.6.1.4.1.14179.2.1.4.1.5	INTEGER	read-only	Slot ID of AP Interface to which the mobile station is associated. The value 15 is used to indicate that the slot Id is invalid.
INT bsnMobileStationEssIndex	1.3.6.1.4.1.14179.2.1.4.1.6	INTEGER	read-only	Ess Index of the Wlan(SSID) that is being used by Mobile Station to connect to AP
STR bsnMobileStationSsid	1.3.6.1.4.1.14179.2.1.4.1.7	DisplayString	read-only	The SSID Advertised by Mobile Station
U32 bsnMobileStationAID	1.3.6.1.4.1.14179.2.1.4.1.8	Unsigned32	read-only	AID for the mobile station
INT bsnMobileStationStatus	1.3.6.1.4.1.14179.2.1.4.1.9	INTEGER	read-only	Status of the mobile station
INT bsnMobileStationReasonCode	1.3.6.1.4.1.14179.2.1.4.1.10	INTEGER	read-only	Reason Code as defined by 802.11 standards
INT bsnMobileStationMobilityStatus	1.3.6.1.4.1.14179.2.1.4.1.11	INTEGER	read-only	Mobility Role of the Mobile Station.
IP bsnMobileStationAnchorAddress	1.3.6.1.4.1.14179.2.1.4.1.12	IpAddress	read-only	If the Mobility Status of the Mobile Station is Anchor then it will have Peer Ip Address and will have Anchor IP if the Role is Foreign
INT bsnMobileStationCFPollable	1.3.6.1.4.1.14179.2.1.4.1.13	INTEGER	read-only	When this attribute is true, it shall indicate that the Mobile Station is able to respond to a CF-Poll with a data frame within a SIFS time. This attribute shall be false if the Mobile Station is not able to respond to a CF-Poll with a data frame within a SIFS time.
INT bsnMobileStationCFPollRequest	1.3.6.1.4.1.14179.2.1.4.1.14	INTEGER	read-only	Specifies whether CFP is requested by Mobile Station or not
INT bsnMobileStationChannelAgilityEnabled	1.3.6.1.4.1.14179.2.1.4.1.15	INTEGER	read-only	This attribute indicates that the PHY channel agility functionality is enabled.
INT bsnMobileStationPBCCOptionImplemented	1.3.6.1.4.1.14179.2.1.4.1.16	INTEGER	read-only	This attribute, when true, shall indicate that the PBCC modulation option as defined in subclause 18.4.6.6 is implemented. The default value of this attribute shall be false.
INT bsnMobileStationShortPreambleOptionImplemented	1.3.6.1.4.1.14179.2.1.4.1.17	INTEGER	read-only	This attribute, when true, shall indicate that the short preamble option as defined in subclause 18.2.2.2 is implemented. The default value of this attribute shall be false.
U32 bsnMobileStationSessionTimeout	1.3.6.1.4.1.14179.2.1.4.1.18	Unsigned32	read-only	Session Timeout of Mobile station
INT bsnMobileStationAuthenticationAlgorithm	1.3.6.1.4.1.14179.2.1.4.1.19	INTEGER	read-only	Authentication Algorithm of Mobile Station
INT bsnMobileStationWepState	1.3.6.1.4.1.14179.2.1.4.1.20	INTEGER	read-only	WEP State of Mobile Station
U32 bsnMobileStationPortNumber	1.3.6.1.4.1.14179.2.1.4.1.21	Unsigned32	read-only	The Port Number of this Airespace Switch on which the traffic of the Mobile Station is coming through.
INT bsnMobileStationDeleteAction	1.3.6.1.4.1.14179.2.1.4.1.22	INTEGER	read-write	Action to Deauthenticate the Mobile Station. Set the State to delete.
STR bsnMobileStationPolicyManagerState	1.3.6.1.4.1.14179.2.1.4.1.23	DisplayString	read-only	Policy Manager State of the mobile station.
INT bsnMobileStationSecurityPolicyStatus	1.3.6.1.4.1.14179.2.1.4.1.24	INTEGER	read-only	When this attribute has value completed, it shall indicate that the Mobile Station has completed the security policy checks. Otherwise the checks are yet to be completed.
INT bsnMobileStationProtocol	1.3.6.1.4.1.14179.2.1.4.1.25	INTEGER	read-only	The 802.11 protocol type of the client. The protocol is mobile when this client detail is seen on the anchor i.e it's mobility status is anchor.
INT bsnMobileStationMirrorMode	1.3.6.1.4.1.14179.2.1.4.1.26	INTEGER	read-write	If enabled, then mirroring for this client will be statically configured irrespective of the AP and the port this client is on.
STR bsnMobileStationInterface	1.3.6.1.4.1.14179.2.1.4.1.27	DisplayString	read-only	Name of the Interface of the mobile client to the switch.
INT bsnMobileStationApMode	1.3.6.1.4.1.14179.2.1.4.1.28	INTEGER	read-only	Mode of the AP to which the Mobile Station is associated.
I32 bsnMobileStationVlanId	1.3.6.1.4.1.14179.2.1.4.1.29	Integer32	read-only	Vlan ID of the Interface to which the client is associated.
INT bsnMobileStationPolicyType	1.3.6.1.4.1.14179.2.1.4.1.30	INTEGER	read-only	Mode of the AP to which the Mobile Station is associated.
INT bsnMobileStationEncryptionCypher	1.3.6.1.4.1.14179.2.1.4.1.31	INTEGER	read-only	Mode of the AP to which the Mobile Station is associated.
INT bsnMobileStationEapType	1.3.6.1.4.1.14179.2.1.4.1.32	INTEGER	read-only	Mode of the AP to which the Mobile Station is associated.
INT bsnMobileStationCcxVersion	1.3.6.1.4.1.14179.2.1.4.1.33	INTEGER	read-only	Represents the Cisco Compatible Extensions (CCX) Version the client is using for communication with the AP.
INT bsnMobileStationE2eVersion	1.3.6.1.4.1.14179.2.1.4.1.34	INTEGER	read-only	Represents the End-2-End Version the client is using for communication with the AP.
INT bsnMobileStationStatusCode	1.3.6.1.4.1.14179.2.1.4.1.42	INTEGER	read-only	Status Code of the Mobile Station
bsnMobileStationPerRadioPerVapTable	1.3.6.1.4.1.14179.2.1.5		not-accessible	Mobile Station Per Radio Per VAP(WLAN) Table. This table lists all Mobile Stations on a particular Airespace AP Interface for a particular ESS(Wlan). It only lists MAC Addresses. Further details for a Mobile Station can be found from bsnMobileStationTable once the MAC Address is knonwn. (Mobile Station is better referred to as Client in the current releases.)
bsnMobileStationPerRadioPerVapEntry	1.3.6.1.4.1.14179.2.1.5.1		not-accessible	An entry in MobileStationPerRadioPerVapTable.
I32 bsnMobileStationPerRadioPerVapIndex	1.3.6.1.4.1.14179.2.1.5.1.1	Integer32	read-only	The index of Mobile Station. The index starts from 1 and goes upto the total number of Mobile Stations on Airespace Radio Interface for a specific ESS (Wlan).
MAC bsnMobileStationMacAddr	1.3.6.1.4.1.14179.2.1.5.1.20	MacAddress	read-only	The MAC Address of Mobile Station.
bsnMobileStationStatsTable	1.3.6.1.4.1.14179.2.1.6		not-accessible	Mobile Station Statistics Table. (Mobile Station is better referred to as Client in the current releases.)
bsnMobileStationStatsEntry	1.3.6.1.4.1.14179.2.1.6.1		not-accessible	An entry in bsnMobileStationStatsTable.
I32 bsnMobileStationRSSI	1.3.6.1.4.1.14179.2.1.6.1.1	Integer32	read-only	Average packet RSSI for the Mobile Station.
C64 bsnMobileStationBytesReceived	1.3.6.1.4.1.14179.2.1.6.1.2	Counter64	read-only	Bytes received from Mobile Station
C64 bsnMobileStationBytesSent	1.3.6.1.4.1.14179.2.1.6.1.3	Counter64	read-only	Bytes sent to Mobile Station
C64 bsnMobileStationPolicyErrors	1.3.6.1.4.1.14179.2.1.6.1.4	Counter64	read-only	Number of Policy Errors for Mobile Station
C64 bsnMobileStationPacketsReceived	1.3.6.1.4.1.14179.2.1.6.1.5	Counter64	read-only	Packets received from Mobile Station
C64 bsnMobileStationPacketsSent	1.3.6.1.4.1.14179.2.1.6.1.6	Counter64	read-only	Packets sent to Mobile Station
I32 bsnMobileStationSnr	1.3.6.1.4.1.14179.2.1.6.1.26	Integer32	read-only	Signal to noise Ratio of the Mobile Station.
bsnRogueAPTable	1.3.6.1.4.1.14179.2.1.7		not-accessible	Rogue Table. This table lists all the Rogue APs detected by Airespace APs.
bsnRogueAPEntry	1.3.6.1.4.1.14179.2.1.7.1		not-accessible	An Entry in bsnRogueAPTable.
MAC bsnRogueAPDot11MacAddress	1.3.6.1.4.1.14179.2.1.7.1.1	MacAddress	read-create	MAC Address of Rogue Station.
I32 bsnRogueAPTotalDetectingAPs	1.3.6.1.4.1.14179.2.1.7.1.2	Integer32	read-only	Total number of Airespace APs that detected this rogue.
STR bsnRogueAPFirstReported	1.3.6.1.4.1.14179.2.1.7.1.3	DisplayString	read-only	Time Stamp when this Rogue was First Detected.
STR bsnRogueAPLastReported	1.3.6.1.4.1.14179.2.1.7.1.4	DisplayString	read-only	Time Stamp when this Rogue was Last Detected.
INT bsnRogueAPContainmentLevel	1.3.6.1.4.1.14179.2.1.7.1.5	INTEGER	read-create	If the state of the rogue is contained, this specifies the level of containment. Higher the level, more the number of detecting APs that are used to contain it. The value must be between 1 to 4 for 'contained' state.
INT bsnRogueAPType	1.3.6.1.4.1.14179.2.1.7.1.6	INTEGER	read-only	This attribute specifies if the Rogue is of ad-hoc type or is an AP.
INT bsnRogueAPOnNetwork	1.3.6.1.4.1.14179.2.1.7.1.7	INTEGER	read-only	This attribute specifies if the Rogue is on Wired Network or not.
I32 bsnRogueAPTotalClients	1.3.6.1.4.1.14179.2.1.7.1.8	Integer32	read-only	Total number of Clients detected on this rogue.
ROW bsnRogueAPRowStatus	1.3.6.1.4.1.14179.2.1.7.1.9	RowStatus	read-create	Row Status
I32 bsnRogueAPMaxDetectedRSSI	1.3.6.1.4.1.14179.2.1.7.1.10	Integer32	read-only	This is the max RSSI value of all the detctecting APs, which have detected this rogue.
BIT bsnRogueAPDetectingAPRadioType	1.3.6.1.4.1.14179.2.1.7.1.12	Bits	read-only	Radio type of detecting APs. If the radio type is detected by dot11bg radio or dot11a radio or both.
MAC bsnRogueAPDetectingAPMacAddress	1.3.6.1.4.1.14179.2.1.7.1.13	MacAddress	read-only	MAC Address of of detecting AP which received max RSSI
INT bsnRogueAPMaxRssiRadioType	1.3.6.1.4.1.14179.2.1.7.1.14	INTEGER	read-only	The radio type of detecting AP which received max RSSI value.
INT bsnRogueAPState	1.3.6.1.4.1.14179.2.1.7.1.24	INTEGER	read-create	This attribute is use to specify the state in which the Rogue AP is user can set the Rogue AP in alert, known or acknowledge state. Alert state means Rogue AP can be a potential threat. Trap will be sent out to trap recipients. Known state means its just internal AP which is not on the same Switch. Acknowledge state means an external AP whose existence is acceptable and not a threat (probably some other company's AP). Contained means containement is initiated and ongoing. Threat is usually the state when the rogue is found on wired network. known(4), knownContained(9) and trustedMissing(10) will appear in known rogue list. known rogues can be pre provisioned and known rogues state can be changed to alert(2)
INT bsnRogueAPClassType	1.3.6.1.4.1.14179.2.1.7.1.25	INTEGER	read-create	The AP class type of the client detected.
I32 bsnRogueAPChannel	1.3.6.1.4.1.14179.2.1.7.1.26	Integer32	read-only	This is the channel number of the last detecting APs, which has detected this rogue.
OCT bsnRogueAPDetectingAPName	1.3.6.1.4.1.14179.2.1.7.1.27	OCTET STRING	read-create	AP name of the detecting AP which received max RSSI
bsnRogueAPAirespaceAPTable	1.3.6.1.4.1.14179.2.1.8		not-accessible	Rogue Station Table. This table lists all the Airespace AP Interfaces that detected a particular Rogue.
bsnRogueAPAirespaceAPEntry	1.3.6.1.4.1.14179.2.1.8.1		not-accessible	An entry in bsnRogueAPAirespaceAPEntry.
MAC bsnRogueAPAirespaceAPMacAddress	1.3.6.1.4.1.14179.2.1.8.1.1	MacAddress	read-only	MAC Address of Airespace AP Interface that Detected the Rogue.
U32 bsnRogueAPAirespaceAPSlotId	1.3.6.1.4.1.14179.2.1.8.1.2	Unsigned32	read-only	The slot ID of the Airespace AP Interface that detected the Rogue.
INT bsnRogueAPRadioType	1.3.6.1.4.1.14179.2.1.8.1.3	INTEGER	read-only	The Airespace AP Interface type that detected the Rogue.
STR bsnRogueAPAirespaceAPName	1.3.6.1.4.1.14179.2.1.8.1.4	DisplayString	read-only	Name of Airespace AP Interface that detected the Rogue.
I32 bsnRogueAPChannelNumber	1.3.6.1.4.1.14179.2.1.8.1.5	Integer32	read-only	The advertised Channel Number of the Airespace AP Interface picked up from the Rogue.
STR bsnRogueAPSSID	1.3.6.1.4.1.14179.2.1.8.1.6	DisplayString	read-only	The SSID Advertised by Rogue Station.
I32 bsnRogueAPAirespaceAPRSSI	1.3.6.1.4.1.14179.2.1.8.1.7	Integer32	read-only	Rogue RSSI as seen by Airespace AP Interface.
INT bsnRogueAPContainmentMode	1.3.6.1.4.1.14179.2.1.8.1.8	INTEGER	read-only	If the rogue is in 'contained' state, this attribute shows the containment mode used by the AP.
U32 bsnRogueAPContainmentChannelCount	1.3.6.1.4.1.14179.2.1.8.1.9	Unsigned32	read-only	The number of channels used for rogue containment.
STR bsnRogueAPContainmentChannels	1.3.6.1.4.1.14179.2.1.8.1.10	DisplayString	read-only	This is the comma separated string of channels used for rogue containment.
C32 bsnRogueAPAirespaceAPLastHeard	1.3.6.1.4.1.14179.2.1.8.1.11	Counter32	read-only	No of seconds ago when this Rogue was last heard by this AP.
INT bsnRogueAPAirespaceAPWepMode	1.3.6.1.4.1.14179.2.1.8.1.12	INTEGER	read-only	The WEP mode on this detecting AP.
INT bsnRogueAPAirespaceAPPreamble	1.3.6.1.4.1.14179.2.1.8.1.13	INTEGER	read-only	The Preamble on this detecting AP.
INT bsnRogueAPAirespaceAPWpaMode	1.3.6.1.4.1.14179.2.1.8.1.14	INTEGER	read-only	The WPA mode on this detecting AP.
I32 bsnRogueAPAirespaceAPSNR	1.3.6.1.4.1.14179.2.1.8.1.27	Integer32	read-only	SNR seen by Airespace AP Interface from Rogue
INT bsnRogueAPChannelWidth	1.3.6.1.4.1.14179.2.1.8.1.28	INTEGER	read-only	This object represents the channel width of the rogue.
bsnThirdPartyAPTable	1.3.6.1.4.1.14179.2.1.9		not-accessible	Third Party Access Point Table. An entry needs to be configured in this table for a third party access point that needs to be supported by the Switch. Note: A third party ESS (Wlan) with ID 17 should be created in bsnDot11EssTable before adding entries here. Please also note that ACS currently supports only Aironet 350, 1200 and Orinoco 2000 Access Points as third party APs.
bsnThirdPartyAPEntry	1.3.6.1.4.1.14179.2.1.9.1		not-accessible	An entry in bsnThirdPartyAPTable.
MAC bsnThirdPartyAPMacAddress	1.3.6.1.4.1.14179.2.1.9.1.1	MacAddress	read-create	MAC Address of Third Party Access Point which is connected directly to this Airespace Switch.
I32 bsnThirdPartyAPInterface	1.3.6.1.4.1.14179.2.1.9.1.2	Integer32	read-create	Interface(Port Number) to which the Third Party AP is connected.
IP bsnThirdPartyAPIpAddress	1.3.6.1.4.1.14179.2.1.9.1.3	IpAddress	read-create	Static IP address of the 3rd Party AP, 0.0.0.0 indicating x its using DHCP
INT bsnThirdPartyAP802Dot1XRequired	1.3.6.1.4.1.14179.2.1.9.1.4	INTEGER	read-create	If 802.1X is required for the 3rd Party AP
INT bsnThirdPartyAPMirrorMode	1.3.6.1.4.1.14179.2.1.9.1.5	INTEGER	read-create	If enabled, then data from all the foreign AP users and all the foreign APs on this APs port will be mirrored. These clients are dynamically added to the switch's mirrored MAC list.
ROW bsnThirdPartyAPRowStatus	1.3.6.1.4.1.14179.2.1.9.1.24	RowStatus	read-create	Row Status in the ThirdPartyAPEntry.
bsnMobileStationByIpTable	1.3.6.1.4.1.14179.2.1.10		not-accessible	Mobile Station Table indexed by bsnMobileStationByIpAddress. NOTE: This is just to facilitate the search of mobile stations based on IP Address. Doing a get without the index doesn't return anything. (Mobile Station is better referred to as Client in the current releases.)
bsnMobileStationByIpEntry	1.3.6.1.4.1.14179.2.1.10.1		not-accessible	An entry in bsnMobileStationByIpTable.
IP bsnMobileStationByIpAddress	1.3.6.1.4.1.14179.2.1.10.1.1	IpAddress	read-only	IP Address of the Mobile Station
MAC bsnMobileStationByIpMacAddress	1.3.6.1.4.1.14179.2.1.10.1.2	MacAddress	read-only	802.11 Mac Address of the Mobile Station.
bsnMobileStationRssiDataTable	1.3.6.1.4.1.14179.2.1.11		not-accessible	Mobile Station RSSI data Table indexed by bsnMobileStationMacAddress, bsnMobileStationRssiDataApMacAddress, bsnMobileStationRssiDataApIfSlotId. (Mobile Station is better referred to as Client in the current releases.)
bsnMobileStationRssiDataEntry	1.3.6.1.4.1.14179.2.1.11.1		not-accessible	An entry in bsnMobileStationRssiDataTable.
MAC bsnMobileStationRssiDataApMacAddress	1.3.6.1.4.1.14179.2.1.11.1.1	MacAddress	read-only	802.11 Mac Address of the AP on which Mobile Station is associated.
U32 bsnMobileStationRssiDataApIfSlotId	1.3.6.1.4.1.14179.2.1.11.1.2	Unsigned32	read-only	SlotId of APIf on which mobile station is associated
INT bsnMobileStationRssiDataApIfType	1.3.6.1.4.1.14179.2.1.11.1.3	INTEGER	read-only	The interface type of the radio that sensed the rssi data.
STR bsnMobileStationRssiDataApName	1.3.6.1.4.1.14179.2.1.11.1.4	DisplayString	read-only	The Name of the AP that sensed the rssi data.
I32 bsnMobileStationRssiData	1.3.6.1.4.1.14179.2.1.11.1.5	Integer32	read-only	RSSI seen by Airespace AP Interface for the Mobile Station
U32 bsnAPIfPhyAntennaIndex	1.3.6.1.4.1.14179.2.1.11.1.6	Unsigned32	read-only	Antenna which recived the probe request from client. The antenna which reported the RSSI value for the client. For now value will be 0 to 1, in future it may change.
C32 bsnMobileStationRssiDataLastHeard	1.3.6.1.4.1.14179.2.1.11.1.25	Counter32	read-only	No of seconds ago when this RSSI data was recorded.
bsnWatchListClientTable	1.3.6.1.4.1.14179.2.1.12		not-accessible	Table of watch listed clients. When clients are added to this table by username or MAC address, ACS collects data for them to show trend reports. The switch generates Client Association and Client Authentication traps for the watch listed clients.The watch list feature can be enbaled or diabled by the bsnWatchListFeatureEnable flag on the switch.
bsnWatchListClientEntry	1.3.6.1.4.1.14179.2.1.12.1		not-accessible	An entry in bsnWatchListClientTable.
OCT bsnWatchListClientKey	1.3.6.1.4.1.14179.2.1.12.1.1	OCTET STRING	read-create	MAC Address or User Name of Client that is to be added to the watch list.
INT bsnWatchListClientType	1.3.6.1.4.1.14179.2.1.12.1.2	INTEGER	read-create	The type of the watch list client entry. The entry can be created by Client MAC Address or by Username.
ROW bsnWatchListClientRowStatus	1.3.6.1.4.1.14179.2.1.12.1.20	RowStatus	read-create	A row status type for the bsnWatchListClientEntry
bsnMobileStationByUsernameTable	1.3.6.1.4.1.14179.2.1.13		not-accessible	Mobile Station Table indexed by the Mobile Station Username and MAC Address. NOTE: This is just to facilitate the search of mobile stations based on User Name. Doing a get without the username doesn't return anything. (Mobile Station is better referred to as Client in the current releases.)
bsnMobileStationByUsernameEntry	1.3.6.1.4.1.14179.2.1.13.1		not-accessible	An entry in bsnMobileStationByUsernameTable.
OCT bsnMobileStationByUserName	1.3.6.1.4.1.14179.2.1.13.1.1	OCTET STRING	read-only	Username of the Mobile Station
MAC bsnMobileStationByUserMacAddress	1.3.6.1.4.1.14179.2.1.13.1.2	MacAddress	read-only	802.11 Mac Address of the Mobile Station.
bsnRogueClientTable	1.3.6.1.4.1.14179.2.1.14		not-accessible	Rogue Client Table. This table lists all the Rogue Clients detected by Airespace APs.
bsnRogueClientEntry	1.3.6.1.4.1.14179.2.1.14.1		not-accessible	An Entry in bsnRogueClientTable.
MAC bsnRogueClientDot11MacAddress	1.3.6.1.4.1.14179.2.1.14.1.1	MacAddress	not-accessible	Mac Address of Rogue Station.
I32 bsnRogueClientTotalDetectingAPs	1.3.6.1.4.1.14179.2.1.14.1.2	Integer32	read-only	Total number of Airespace APs that detected this rogue.
STR bsnRogueClientFirstReported	1.3.6.1.4.1.14179.2.1.14.1.3	DisplayString	read-only	Time Stamp when this Rogue was First Detected.
STR bsnRogueClientLastReported	1.3.6.1.4.1.14179.2.1.14.1.4	DisplayString	read-only	Time Stamp when this Rogue was Last Detected.
MAC bsnRogueClientBSSID	1.3.6.1.4.1.14179.2.1.14.1.5	MacAddress	read-only	This attribute specifies BSSID of the Rogue Client.
INT bsnRogueClientContainmentLevel	1.3.6.1.4.1.14179.2.1.14.1.6	INTEGER	read-write	If the state of the rogue is contained, this specifies the level of containment. Higher the level, more the number of detecting APs that are used to contain it. The value must be between 1 to 4 for 'contained' state.
I32 bsnRogueClientLastHeard	1.3.6.1.4.1.14179.2.1.14.1.7	Integer32	read-only	Number of seconds ago this rogue client was detected.
INT bsnRogueClientState	1.3.6.1.4.1.14179.2.1.14.1.24	INTEGER	read-write	This attribute is use to specify the state in which the Rogue AP is. User can set the Rogue Client in alert,known or acknowledge state. Alert state means Rogue Client can be a potential i threat.Trap will be sent out to trap recipients. Known state means its just internal Client which is not on the same Switch. Acknowledge state means an external Client whose existence is acceptable and not a threat (probably some other company's AP). Contained means containement is initiated and ongoing
bsnRogueClientAirespaceAPTable	1.3.6.1.4.1.14179.2.1.15		not-accessible	Rogue Station Table. This table lists all the Airespace AP Interface that detected a particular Rogue.
bsnRogueClientAirespaceAPEntry	1.3.6.1.4.1.14179.2.1.15.1		not-accessible	An entry in bsnRogueClientAirespaceAPEntry.
MAC bsnRogueClientAirespaceAPMacAddress	1.3.6.1.4.1.14179.2.1.15.1.1	MacAddress	read-only	Mac Address of Airespace AP Interface that Detected the Rogue.
U32 bsnRogueClientAirespaceAPSlotId	1.3.6.1.4.1.14179.2.1.15.1.2	Unsigned32	read-only	The slotId of the Airespace AP Interface that detected the Rogue.
INT bsnRogueClientRadioType	1.3.6.1.4.1.14179.2.1.15.1.3	INTEGER	read-only	The advertised SSID that the Airespace AP Interface picked up from the Rogue.
STR bsnRogueClientAirespaceAPName	1.3.6.1.4.1.14179.2.1.15.1.4	DisplayString	read-only	Name of Airespace AP Interface that detected the Rogue.
I32 bsnRogueClientChannelNumber	1.3.6.1.4.1.14179.2.1.15.1.5	Integer32	read-only	The advertised Channel Number of that the Airespace AP Interface picked up from the Rogue.
I32 bsnRogueClientAirespaceAPRSSI	1.3.6.1.4.1.14179.2.1.15.1.7	Integer32	read-only	RSSI seen by Airespace AP Interface from the Rogue
STR bsnRogueClientAirespaceAPLastHeard	1.3.6.1.4.1.14179.2.1.15.1.11	DisplayString	read-only	No of seconds ago when this Rogue was last heard by this AP.
I32 bsnRogueClientAirespaceAPSNR	1.3.6.1.4.1.14179.2.1.15.1.27	Integer32	read-only	SNR seen by Airespace AP Interface from Rogue
bsnRogueClientPerRogueAPTable	1.3.6.1.4.1.14179.2.1.16		not-accessible	Rogue Clients for each rogue. This table lists all Rogue Clients on a particular Rogue.
bsnRogueClientPerRogueAPEntry	1.3.6.1.4.1.14179.2.1.16.1		not-accessible	An entry in RogueClientPerRogueAPTable.
MAC bsnRogueAPDot11MacAddr	1.3.6.1.4.1.14179.2.1.16.1.1	MacAddress	read-only	The MAC Address of the Rogue AP.
MAC bsnRogueClientDot11MacAddr	1.3.6.1.4.1.14179.2.1.16.1.20	MacAddress	read-only	MAC Address of the Rogue Client.
bsnDot11QosProfileTable	1.3.6.1.4.1.14179.2.1.17		not-accessible	QOS Profiles specified in bsnDot11EssTable can be customized in this table. This is a lookup table for auto created profiles
bsnDot11QosProfileEntry	1.3.6.1.4.1.14179.2.1.17.1		not-accessible	An entry in bsnDot11QosProfileTable.
OCT bsnDot11QosProfileName	1.3.6.1.4.1.14179.2.1.17.1.1	OCTET STRING	read-only	QOS Profile Name. This will be one of bronze,gold, platinum,silver,uranium.
OCT bsnDot11QosProfileDesc	1.3.6.1.4.1.14179.2.1.17.1.2	OCTET STRING	read-write	QOS Profile Description.
INT bsnDot11QosAverageDataRate	1.3.6.1.4.1.14179.2.1.17.1.3	INTEGER	read-write	This is one of the per user bandwidth contracts(k). Specifies Average Data Rate per user. Value of 0 indicates the feature is disabled.
INT bsnDot11QosBurstDataRate	1.3.6.1.4.1.14179.2.1.17.1.4	INTEGER	read-write	This is one of the per user bandwidth contracts(k). Specifies Average Burst Data Rate per user. Value of 0 indicates the feature is disabled.
INT bsnDot11QosAvgRealTimeDataRate	1.3.6.1.4.1.14179.2.1.17.1.5	INTEGER	read-write	This is one of the per user bandwidth contracts(k). Specifies Average Real Time Data Rate per user. Value of 0 indicates the feature is disabled.
INT bsnDot11QosBurstRealTimeDataRate	1.3.6.1.4.1.14179.2.1.17.1.6	INTEGER	read-write	This is one of the per user bandwidth contracts(k). Specifies Burst Real Time Data Rate per user. Value of 0 indicates the feature is disabled.
INT bsnDot11QosMaxRFUsagePerAP	1.3.6.1.4.1.14179.2.1.17.1.7	INTEGER	read-write	This is one of the over the Air QOS parameter. Specifies maximum RF Usage per AP in percentage.
INT bsnDot11QosProfileQueueDepth	1.3.6.1.4.1.14179.2.1.17.1.8	INTEGER	read-write	This is one of the over the Air QOS parameter. Specifies Queue depth for the current profile.
INT bsnDot11WiredQosProtocol	1.3.6.1.4.1.14179.2.1.17.1.9	INTEGER	read-write	This is one of the over the Air QOS parameter. Specifies Queue depth for the current profile.
INT bsnDot11802Dot1PTag	1.3.6.1.4.1.14179.2.1.17.1.10	INTEGER	read-write	Specifies the type of wired QOS protocol for the current profile. Value of 0 indicates the feature is disabled.
INT bsnDot11ResetProfileToDefault	1.3.6.1.4.1.14179.2.1.17.1.40	INTEGER	read-write	Set this attribute to reset to restore the factory default value for the profile.
bsnTagTable	1.3.6.1.4.1.14179.2.1.18		not-accessible	RF ID Tag Table indexed by bsnTagDot11MacAddress.
bsnTagEntry	1.3.6.1.4.1.14179.2.1.18.1		not-accessible	An entry in bsnTagTable.
MAC bsnTagDot11MacAddress	1.3.6.1.4.1.14179.2.1.18.1.1	MacAddress	read-only	802.11 MAC Address of the RF ID Tag.
INT bsnTagType	1.3.6.1.4.1.14179.2.1.18.1.2	INTEGER	read-only	Type of the RF ID Tag.
U32 bsnTagTimeInterval	1.3.6.1.4.1.14179.2.1.18.1.3	Unsigned32	read-only	Time Interval after which the tag transmits data.
INT bsnTagBatteryStatus	1.3.6.1.4.1.14179.2.1.18.1.4	INTEGER	read-only	Battery Status of the RF ID Tag.
U32 bsnTagLastReported	1.3.6.1.4.1.14179.2.1.18.1.23	Unsigned32	read-only	No of seconds ago when this tag was heard by any AP.
bsnTagRssiDataTable	1.3.6.1.4.1.14179.2.1.19		not-accessible	RF ID Tag Detecting AP Table indexed by bsnTagDot11MacAddress, bsnTagRssiDataApMacAddress and bsnTagRssiDataApIfSlotId.
bsnTagRssiDataEntry	1.3.6.1.4.1.14179.2.1.19.1		not-accessible	An entry in bsnTagRssiDataTable.
MAC bsnTagRssiDataApMacAddress	1.3.6.1.4.1.14179.2.1.19.1.1	MacAddress	read-only	802.11 MAC Address of the AP detecting the RF ID Tag.
U32 bsnTagRssiDataApIfSlotId	1.3.6.1.4.1.14179.2.1.19.1.2	Unsigned32	read-only	Slot Id of the radio on AP detecting the RF ID Tag.
INT bsnTagRssiDataApIfType	1.3.6.1.4.1.14179.2.1.19.1.3	INTEGER	read-only	Interface Type of the radio on AP detecting the RF ID Tag.
STR bsnTagRssiDataApName	1.3.6.1.4.1.14179.2.1.19.1.4	DisplayString	read-only	Name of the AP detecting the RF ID Tag.
C32 bsnTagRssiDataLastHeard	1.3.6.1.4.1.14179.2.1.19.1.5	Counter32	read-only	No of seconds ago when this tag was heard by this detecting AP.
I32 bsnTagRssiData	1.3.6.1.4.1.14179.2.1.19.1.6	Integer32	read-only	RSSI of the RF ID Tag as seen by the radio on this detecting AP.
I32 bsnTagRssiDataSnr	1.3.6.1.4.1.14179.2.1.19.1.26	Integer32	read-only	SNR of the RF ID tag as seen by the radio on this detecting AP.
bsnTagStatsTable	1.3.6.1.4.1.14179.2.1.20		not-accessible	RF ID Tag Statistics Table.
bsnTagStatsEntry	1.3.6.1.4.1.14179.2.1.20.1		not-accessible	An entry in bsnTagStatsTable.
U32 bsnTagBytesReceived	1.3.6.1.4.1.14179.2.1.20.1.1	Unsigned32	read-only	Bytes received from an RF ID Tag
U32 bsnTagPacketsReceived	1.3.6.1.4.1.14179.2.1.20.1.20	Unsigned32	read-only	Packets received from an RF ID Tag
bsnMobileStationExtStatsTable	1.3.6.1.4.1.14179.2.1.21		not-accessible	This table was supported only by indoor mesh AP -cisco 1000. As this AP is not supported after 4.2.x.x. This table has been marked obsolete. Mobile Station Extended Statistics Table. (Mobile Station is better referred to as Client in the current releases.)
bsnMobileStationExtStatsEntry	1.3.6.1.4.1.14179.2.1.21.1		not-accessible	An entry in bsnMobileStationExtStatsTable.
I32 bsnMobileStationSampleTime	1.3.6.1.4.1.14179.2.1.21.1.1	Integer32	read-only	Time stats were sampled as seconds since the epoch.
C64 bsnMobileStationTxExcessiveRetries	1.3.6.1.4.1.14179.2.1.21.1.2	Counter64	read-only	Tx packets dropped due to excessive retries.
C64 bsnMobileStationTxRetries	1.3.6.1.4.1.14179.2.1.21.1.3	Counter64	read-only	Tx packets retransmitted.
C64 bsnMobileStationTxFiltered	1.3.6.1.4.1.14179.2.1.21.1.20	Counter64	read-only	Tx packets dropped by the built-in Tx filter
bsnAP	1.3.6.1.4.1.14179.2.2
bsnAPTable	1.3.6.1.4.1.14179.2.2.1		not-accessible	Table of Airespace APs managed by this Airespace Switch.
bsnAPEntry	1.3.6.1.4.1.14179.2.2.1.1		not-accessible	An entry in the bsnAPTable.
MAC bsnAPDot3MacAddress	1.3.6.1.4.1.14179.2.2.1.1.1	MacAddress	read-only	The MAC address of an AP.
INT bsnAPNumOfSlots	1.3.6.1.4.1.14179.2.2.1.1.2	INTEGER	read-only	Number of Radio Interfaces on the Airespace AP. Currently maximum two interfaces are supported. One would be of type 802.11a and other of type 802.11b/g.
OCT bsnAPName	1.3.6.1.4.1.14179.2.2.1.1.3	OCTET STRING	read-write	Name assigned to this AP. If an AP is not configured its factory default name will be ap: eg. ap:af:12:be
OCT bsnAPLocation	1.3.6.1.4.1.14179.2.2.1.1.4	OCTET STRING	read-write	User specified location of this AP. While configuring AP, user should specify a location for the AP so that its easy to figure out for some one where the AP is located.
INT bsnAPMonitorOnlyMode	1.3.6.1.4.1.14179.2.2.1.1.5	INTEGER	read-write	Monitor Only Mode Setting.
INT bsnAPOperationStatus	1.3.6.1.4.1.14179.2.2.1.1.6	INTEGER	read-only	Operation State of the AP. When AP associates with the Airespace Switch its state will be associated. When Airespace AP is disassociated from the Switch, its state will be disassociating. The state is downloading when the AP is downloading its firmware.
STR bsnAPSoftwareVersion	1.3.6.1.4.1.14179.2.2.1.1.8	DisplayString	read-only	Major Minor Software Version of AP
STR bsnAPBootVersion	1.3.6.1.4.1.14179.2.2.1.1.9	DisplayString	read-only	Major Minor Boot Version of AP
OCT bsnAPPrimaryMwarName	1.3.6.1.4.1.14179.2.2.1.1.10	OCTET STRING	read-write	sysName of the Airespace Switch which is suppose to be the Primary MWAR(switch) of the AP with which AP should associate. This work when AP is not directly connected to Airespace Switch, it tries to find Primary Switch and associates with it. If this attribute is left empty or AP is not able to find the Airespace Switch with this name, then it will associate with Secondary Switch.
INT bsnAPReset	1.3.6.1.4.1.14179.2.2.1.1.11	INTEGER	read-write	Set this attribute to reset the AP. When it comes up it will try to associate with the Primary Switch if that is set, else it will associate with the Master Switch. Reading this attribute will always return 0
INT bsnAPStatsTimer	1.3.6.1.4.1.14179.2.2.1.1.12	INTEGER	read-write	Configures the time interval in secs after which bsnAPDot11Counters Stats is sent from AP to Switch. If not configured this value is 0 which means never send the stats.
INT bsnAPPortNumber	1.3.6.1.4.1.14179.2.2.1.1.13	INTEGER	read-only	Port on the Switch on which this APs traffic is coming through.
STR bsnAPModel	1.3.6.1.4.1.14179.2.2.1.1.16	DisplayString	read-only	AP Model
STR bsnAPSerialNumber	1.3.6.1.4.1.14179.2.2.1.1.17	DisplayString	read-only	AP Serial Number.
INT bsnAPClearConfig	1.3.6.1.4.1.14179.2.2.1.1.18	INTEGER	read-write	Set this attribute to clear AP configuration and reset it to factory defaults. A value of clearAll(2) resets all values to factory defaults. A value of clear(1) resets all values except static IP of the AP. Reading this attribute will always return 0
IP bsnApIpAddress	1.3.6.1.4.1.14179.2.2.1.1.19	IpAddress	read-write	IP address of the AP. This will not be available when the switch is operating in the Layer2 mode. In this case, the attribute will return 0 as value.
INT bsnAPMirrorMode	1.3.6.1.4.1.14179.2.2.1.1.20	INTEGER	read-write	If enabled, then this AP's Client's Data is mirrored and this AP's clients are dynamically added to the switch's mirrored MAC list.
INT bsnAPRemoteModeSupport	1.3.6.1.4.1.14179.2.2.1.1.21	INTEGER	read-only	This specifies if the the Remote Mode is supported on this AP or not. If supported user can set bsnAPMonitorOnlyMode to remote. Otherwise not.
INT bsnAPType	1.3.6.1.4.1.14179.2.2.1.1.22	INTEGER	read-only	This is the model of the AP in enumeration.
OCT bsnAPSecondaryMwarName	1.3.6.1.4.1.14179.2.2.1.1.23	OCTET STRING	read-write	sysName of the Airespace Switch which is suppose to be the Secondary MWAR(switch) of the AP with which AP should associate if Primary Switch(configured through bsnAPPrimaryMwarName) is not available. If primary and secondary switches are not available then AP will associate with the tertiary switch.
OCT bsnAPTertiaryMwarName	1.3.6.1.4.1.14179.2.2.1.1.24	OCTET STRING	read-write	sysName of the Airespace Switch which is suppose to be the Tertiary MWAR(switch) of the AP with which AP should associate. If primary,secondary and tertiary switch are not available then it will associate with Master Switch.
INT bsnAPIsStaticIP	1.3.6.1.4.1.14179.2.2.1.1.25	INTEGER	read-write	This flag when disabled implies that AP will use DHCP to get the IP address. However, if it is enabled, then user should enter the IPAddress, Netmask and Gateway.
IP bsnAPNetmask	1.3.6.1.4.1.14179.2.2.1.1.26	IpAddress	read-write	The Netmask of the IP address of the AP.
IP bsnAPGateway	1.3.6.1.4.1.14179.2.2.1.1.27	IpAddress	read-write	The Gateway for the AP.
IP bsnAPStaticIPAddress	1.3.6.1.4.1.14179.2.2.1.1.28	IpAddress	read-write	The Static IP-Address configuration for the AP. This can only be changed when the LWAPP mode is in Layer-3.
INT bsnAPBridgingSupport	1.3.6.1.4.1.14179.2.2.1.1.29	INTEGER	read-write	This specifies if this AP is a Bridging AP. Bridging APs can be used in Bridging or Mesh network configurations.
OCT bsnAPGroupVlanName	1.3.6.1.4.1.14179.2.2.1.1.30	OCTET STRING	read-write	The AP Group to which this AP has been associated with. If it is empty, then no AP Group overriding has been set.
STR bsnAPIOSVersion	1.3.6.1.4.1.14179.2.2.1.1.31	DisplayString	read-only	IOS Version of IOS Cisco AP. Zero length string will be returned for other APs
INT bsnAPCertificateType	1.3.6.1.4.1.14179.2.2.1.1.32	INTEGER	read-only	Enum values denoting AP Certificate Type. 1 : manufactureinstalled : Manufacture Installed Certificate type (MIC). 2 : selfsigned : Self Signed Certificate type (SSC). 3 : localsignificance : Local Significance.
MAC bsnAPEthernetMacAddress	1.3.6.1.4.1.14179.2.2.1.1.33	MacAddress	read-only	The Ethernet MAC address of the AP.
INT bsnAPAdminStatus	1.3.6.1.4.1.14179.2.2.1.1.37	INTEGER	read-write	Admin State of the AP
bsnAPIfTable	1.3.6.1.4.1.14179.2.2.2		not-accessible	Each entry represents an 802.11 interface in an Airespace AP.
bsnAPIfEntry	1.3.6.1.4.1.14179.2.2.2.1		not-accessible	An entry in bsnAPIfTable.
U32 bsnAPIfSlotId	1.3.6.1.4.1.14179.2.2.2.1.1	Unsigned32	read-only	The slotId of this interface.
INT bsnAPIfType	1.3.6.1.4.1.14179.2.2.2.1.2	INTEGER	read-only	The type of this interface. dot11b also implies 802.11b/g.
INT bsnAPIfPhyChannelAssignment	1.3.6.1.4.1.14179.2.2.2.1.3	INTEGER	read-write	If this value is true, then bsnAPDot11CurrentChannel in bsnAPIfDot11PhyDSSSTable is assigned by dynamic algorithm and is read-only.
INT bsnAPIfPhyChannelNumber	1.3.6.1.4.1.14179.2.2.2.1.4	INTEGER	read-write	Current channel number of the AP Interface. Channel numbers will be from 1 to 14 for 802.11b interface type. Channel numbers will be from 34 to 173 for 802.11a interface type. Allowed channel numbers also depends on the current Country Code set in the Switch. This attribute cannot be set unless bsnAPIfPhyChannelAssignment is set to customized else this attribute gets assigned by dynamic algorithm.
INT bsnAPIfPhyTxPowerControl	1.3.6.1.4.1.14179.2.2.2.1.5	INTEGER	read-write	If this value is true, then bsnAPIfPhyTxPowerLevel is assigned by dynamic algorithm and is read-only.
INT bsnAPIfPhyTxPowerLevel	1.3.6.1.4.1.14179.2.2.2.1.6	INTEGER	read-write	The TxPowerLevel currently being used to transmit data. Some PHYs also use this value to determine the receiver sensitivity requirements for CCA. Valid values are between 1 to 8,depnding on what radio, and this attribute can be set only if bsnAPIfPhyTxPowerControl is set to customized.
INT bsnAPIfPhyAntennaMode	1.3.6.1.4.1.14179.2.2.2.1.7	INTEGER	read-write	Antenna Mode of the AP Interface. For 802.11a this attribute will always be omni for now. This attribute doesn't apply to interface of type 802.11b.
INT bsnAPIfPhyAntennaType	1.3.6.1.4.1.14179.2.2.2.1.8	INTEGER	read-write	This attribute specified if the Antenna currently used by AP Radio is internal or external. For 802.11a the antenna is always internal. For 802.11b you can set antenna type to be external or internal.
INT bsnAPIfPhyAntennaDiversity	1.3.6.1.4.1.14179.2.2.2.1.9	INTEGER	read-write	Diversity doesn't apply to AP Radio of type 802.11a. For 802.11b you can set it to connectorA, connectorB or enabled.
U32 bsnAPIfCellSiteConfigId	1.3.6.1.4.1.14179.2.2.2.1.10	Unsigned32	read-write	In a cell site configuration, this would be the cell Id of this AP Interface
INT bsnAPIfNumberOfVaps	1.3.6.1.4.1.14179.2.2.2.1.11	INTEGER	read-only	Number of WLANs currently active on this AP Interface.
INT bsnAPIfOperStatus	1.3.6.1.4.1.14179.2.2.2.1.12	INTEGER	read-only	Operational status of the interface.
INT bsnAPIfPortNumber	1.3.6.1.4.1.14179.2.2.2.1.13	INTEGER	read-only	Port number on Airespace Switch on which the traffic from this AP interface is received.
INT bsnAPIfPhyAntennaOptions	1.3.6.1.4.1.14179.2.2.2.1.14	INTEGER	read-only	This attribute specifies the Antenna types supported by the AP Radio whether it is internal or external or both. internalAndExternal(0)- internal and external antenna for both 11a and 11b internal(1) - only internal antenna is allowed. siacAp- 11b internal and 11a external external - only external antenna is allowed for 11a and 11b ext11bInt11a - external antenna for 11b and internal antenna for 11a.
C32 bsnApIfNoOfUsers	1.3.6.1.4.1.14179.2.2.2.1.15	Counter32	read-only	No of Users associated with this radio.
INT bsnAPIfWlanOverride	1.3.6.1.4.1.14179.2.2.2.1.16	INTEGER	read-write	This flag when disabled implies that all WLANs are available from this radio. However, if this is enabled, then only those WLANs that appear in the bsnApIfWlanOverrideTable will be available from this radio.
INT bsnAPIfPacketsSniffingFeature	1.3.6.1.4.1.14179.2.2.2.1.17	INTEGER	read-write	This flag when enabled implies that AP will sniff the 802.11a/bg packets. However, if it is enabled, then user should enter the server-ip-address on which Airopeek is running and the 802.11a/bg-channel-number to be sniffed. The above feature will work only when AP is in 'Sniffer' mode.
INT bsnAPIfSniffChannel	1.3.6.1.4.1.14179.2.2.2.1.18	INTEGER	read-write	This the 802.11a/bg-channel-number on which AP will sniff the packets.
IP bsnAPIfSniffServerIPAddress	1.3.6.1.4.1.14179.2.2.2.1.19	IpAddress	read-write	The machine ip address on which Airopeek application is running.
INT bsnAPIfAntennaGain	1.3.6.1.4.1.14179.2.2.2.1.20	INTEGER	read-write	Represents antenna gain in multiple of 0.5 dBi. An integer value 4 means 4 x 0.5 = 2 dBi of gain
STR bsnAPIfChannelList	1.3.6.1.4.1.14179.2.2.2.1.21	DisplayString	read-write	List of comma separated channels supported by this radio.
STR bsnAPIfAbsolutePowerList	1.3.6.1.4.1.14179.2.2.2.1.22	DisplayString	read-write	List of comma separated absolute power levels supported by this radio.
INT bsnAPIfRegulatoryDomainSupport	1.3.6.1.4.1.14179.2.2.2.1.23	INTEGER	read-only	If the regulatory domain on radio is supported or notSupported on the controller
INT bsnAPIfAdminStatus	1.3.6.1.4.1.14179.2.2.2.1.34	INTEGER	read-write	Admin status of the interface.
bsnAPIfSmtParamTable	1.3.6.1.4.1.14179.2.2.3		not-accessible	Each entry represents SMT parameters on an 802.11 interface of an Airespace AP.
bsnAPIfSmtParamEntry	1.3.6.1.4.1.14179.2.2.3.1		not-accessible	An entry in bsnAPIfSmtParamTable
INT bsnAPIfDot11BeaconPeriod	1.3.6.1.4.1.14179.2.2.3.1.1	INTEGER	read-only	This attribute shall specify the number of TU that a AP Interface shall use for scheduling Beacon tranmissions. This value is transmitted in Beacon and Probe Response frames.
INT bsnAPIfDot11MediumOccupancyLimit	1.3.6.1.4.1.14179.2.2.3.1.2	INTEGER	read-only	This attribute shall indicate the maximum amount of time, in TU, that a point coordinator may control the usage of the wireless medium without relinquishing control for long enough to allow at least one instance of DCF access to the medium. The default value of this attribute shall be 100, and the maximum value shall be 1000.
INT bsnAPIfDot11CFPPeriod	1.3.6.1.4.1.14179.2.2.3.1.3	INTEGER	read-only	The attribute shall describe the number of DTIM intervals between the start of CFPs. It is modified by MLME-START.request primitive.
INT bsnAPIfDot11CFPMaxDuration	1.3.6.1.4.1.14179.2.2.3.1.4	INTEGER	read-only	The attribute shall describe the maximum duration of the CFP in TU that may be generated by the PCF. It is modified by MLME-START.request primitive.
OCT bsnAPIfDot11OperationalRateSet	1.3.6.1.4.1.14179.2.2.3.1.5	OCTET STRING	read-only	This attribute shall specify the set of data rates at which the AP Interface may transmit data. Each octet contains a value representing a rate. Each rate shall be within the range from 2 to 127, corresponding to data rates in increments of 500 kb/s from 1 Mb/s to 63.5 Mb/s, and shall be supported (as indicated in the supported rates table) for receiving data. This value is reported in transmitted Beacon, Probe Request, Probe Response, Association Request, Association Response, Reassociation Request, and Reassociation Response frames, and is used to determine whether a BSS with which the AP Interface desires to synchronize is suitable. It is also used when starting a BSS, as specified in 10.3.
INT bsnAPIfDot11DTIMPeriod	1.3.6.1.4.1.14179.2.2.3.1.6	INTEGER	read-only	This attribute shall specify the number of beacon intervals that shall elapse between transmission of Beacons frames containing a TIM element whose DTIM Count field is 0. This value is transmitted in the DTIM Period field of Beacon frames.
INT bsnAPIfDot11MultiDomainCapabilityImplemented	1.3.6.1.4.1.14179.2.2.3.1.7	INTEGER	read-only	This attribute, when TRUE, indicates that the AP Interface implementation is capable of supporting multiple regulatory domains. The capability is disabled, otherwise. The default value of this attribute is FALSE.
INT bsnAPIfDot11MultiDomainCapabilityEnabled	1.3.6.1.4.1.14179.2.2.3.1.8	INTEGER	read-only	This attribute, when TRUE, indicates that the capability of the AP Interface to operate in multiple regulatory domains is enabled. The capability is disabled, otherwise. The default value of this attribute is FALSE.
OCT bsnAPIfDot11CountryString	1.3.6.1.4.1.14179.2.2.3.1.9	OCTET STRING	read-only	This attribute identifies the country in which the AP Interface is operating. The first two octets of this string is the two character country code as described in document ISO/IEC 3166-1. The third octet shall be one of the following: 1. an ASCII space character, if the regulations under which the AP Interface is operating encompass all environments in the country, 2. an ASCII 'O' character, if the regulations under which the AP Interface is operating are for an Outdoor environment only, or 3. an ASCII 'I' character, if the regulations under which the AP Interface is operating are for an Indoor environment only.
INT bsnAPIfDot11SmtParamsConfigType	1.3.6.1.4.1.14179.2.2.3.1.10	INTEGER	read-only	This attribute suggests if the Station parameters for this radio are automatically set or have been customized.
MAC bsnAPIfDot11BSSID	1.3.6.1.4.1.14179.2.2.3.1.30	MacAddress	read-only	BSSID of this AP config which would be the MAC Address of AP
bsnAPIfMultiDomainCapabilityTable	1.3.6.1.4.1.14179.2.2.4		not-accessible	Each entry represents an 803.2 or an 802.11 interface in an Airespace AP.
bsnAPIfMultiDomainCapabilityEntry	1.3.6.1.4.1.14179.2.2.4.1		not-accessible	Each entry represents an 803.2 or an 802.11 interface in an Airespace AP.
I32 bsnAPIfDot11MaximumTransmitPowerLevel	1.3.6.1.4.1.14179.2.2.4.1.1	Integer32	read-only	This attribute shall indicate the maximum transmit power, in dBm, allowed in the subband for the associated domain country string. The default value of this attribute shall be zero.
I32 bsnAPIfDot11FirstChannelNumber	1.3.6.1.4.1.14179.2.2.4.1.2	Integer32	read-only	This attribute shall indicate the value of the lowest channel number in the subband for the associated domain country string. The default value of this attribute shall be zero.
I32 bsnAPIfDot11NumberofChannels	1.3.6.1.4.1.14179.2.2.4.1.20	Integer32	read-only	This attribute shall indicate the value of the total number of channels allowed in the subband for the associated domain country string. The default value of this attribute shall be zero.
bsnAPIfMacOperationParamTable	1.3.6.1.4.1.14179.2.2.5		not-accessible	Group contains MAC attributes pertaining to the operation of the MAC. These would be read only attributes as they would be updated by RRM Dynamic Algorithm. If user needs to configure them then they can only be configured globally
bsnAPIfMacOperationParamEntry	1.3.6.1.4.1.14179.2.2.5.1		not-accessible	An entry in the bsnAPIfMacOperationParamEntry Table. Interface tables in this MIB module are indexed by bsnAPDot3MacAddress, bsnAPIfSlotId.
INT bsnAPIfDot11MacRTSThreshold	1.3.6.1.4.1.14179.2.2.5.1.1	INTEGER	read-only	If bsnAPIfMacParamsAutomaticOn is true then this is read only parameter updated by RRM dynamic algorithm
INT bsnAPIfDot11MacShortRetryLimit	1.3.6.1.4.1.14179.2.2.5.1.2	INTEGER	read-only	If bsnAPIfMacParamsAutomaticOn is true then this is read only parameter updated by RRM dynamic algorithm
INT bsnAPIfDot11MacLongRetryLimit	1.3.6.1.4.1.14179.2.2.5.1.3	INTEGER	read-only	If bsnAPIfMacParamsAutomaticOn is true then this is read only parameter updated by RRM dynamic algorithm
INT bsnAPIfDot11MacFragmentationThreshold	1.3.6.1.4.1.14179.2.2.5.1.4	INTEGER	read-only	If bsnAPIfMacParamsAutomaticOn is true then this is read only parameter updated by RRM dynamic algorithm
U32 bsnAPIfDot11MacMaxTransmitMSDULifetime	1.3.6.1.4.1.14179.2.2.5.1.5	Unsigned32	read-only	If bsnAPIfMacParamsAutomaticOn is true then this is read only parameter updated by RRM dynamic algorithm
INT bsnAPIfDot11MacParamsConfigType	1.3.6.1.4.1.14179.2.2.5.1.6	INTEGER	read-only	This attribute suggests if the MAC parameters for this radio are automatically set or have been customized.
U32 bsnAPIfDot11MacMaxReceiveLifetime	1.3.6.1.4.1.14179.2.2.5.1.25	Unsigned32	read-only	If bsnAPIfMacParamsAutomaticOn is true then this is read only parameter updated by RRM dynamic algorithm
bsnAPIfDot11CountersTable	1.3.6.1.4.1.14179.2.2.6		not-accessible	Group containing attributes that are MAC counters. Each instance represents counters on a AP dot11 interface
bsnAPIfDot11CountersEntry	1.3.6.1.4.1.14179.2.2.6.1		not-accessible	An entry in the dot11CountersEntry Table. Interface tables in this MIB module are indexed by bsnAPDot3MacAddress and bsnAPIfSlotId
C32 bsnAPIfDot11TransmittedFragmentCount	1.3.6.1.4.1.14179.2.2.6.1.1	Counter32	read-only	This counter shall be incremented for an acknowledged MPDU with an individual address in the address 1 field or an MPDU with a multicast address in the address 1 field of type Data or Management.
C32 bsnAPIfDot11MulticastTransmittedFrameCount	1.3.6.1.4.1.14179.2.2.6.1.2	Counter32	read-only	This counter shall increment only when the multicast bit is set in the destination MAC address of a successfully transmitted MSDU. When operating as a STA in an ESS, where these frames are directed to the AP, this implies having received an acknowledgment to all associated MPDUs.
C32 bsnAPIfDot11RetryCount	1.3.6.1.4.1.14179.2.2.6.1.3	Counter32	read-only	This counter shall increment when an MSDU is successfully transmitted after one or more retransmissions.
C32 bsnAPIfDot11MultipleRetryCount	1.3.6.1.4.1.14179.2.2.6.1.4	Counter32	read-only	This counter shall increment when an MSDU is successfully transmitted after more than one retransmission.
C32 bsnAPIfDot11FrameDuplicateCount	1.3.6.1.4.1.14179.2.2.6.1.5	Counter32	read-only	This counter shall increment when a frame is received that the Sequence Control field indicates is a duplicate.
C32 bsnAPIfDot11RTSSuccessCount	1.3.6.1.4.1.14179.2.2.6.1.6	Counter32	read-only	This counter shall increment when a CTS is received in response to an RTS.
C32 bsnAPIfDot11RTSFailureCount	1.3.6.1.4.1.14179.2.2.6.1.7	Counter32	read-only	This counter shall increment when a CTS is not received in response to an RTS.
C32 bsnAPIfDot11ACKFailureCount	1.3.6.1.4.1.14179.2.2.6.1.8	Counter32	read-only	This counter shall increment when an ACK is not received when expected.
C32 bsnAPIfDot11ReceivedFragmentCount	1.3.6.1.4.1.14179.2.2.6.1.9	Counter32	read-only	This counter shall be incremented for each successfully received MPDU of type Data or Management.
C32 bsnAPIfDot11MulticastReceivedFrameCount	1.3.6.1.4.1.14179.2.2.6.1.10	Counter32	read-only	This counter shall increment when a MSDU is received with the multicast bit set in the destination MAC address.
C32 bsnAPIfDot11FCSErrorCount	1.3.6.1.4.1.14179.2.2.6.1.11	Counter32	read-only	This counter shall increment when an FCS error is detected in a received MPDU.
C32 bsnAPIfDot11TransmittedFrameCount	1.3.6.1.4.1.14179.2.2.6.1.12	Counter32	read-only	This counter shall increment for each successfully transmitted MSDU.
C32 bsnAPIfDot11WEPUndecryptableCount	1.3.6.1.4.1.14179.2.2.6.1.13	Counter32	read-only	This counter shall increment when a frame is received with the WEP subfield of the Frame Control field set to one and the WEPOn value for the key mapped to the TA's MAC address indicates that the frame should not have been encrypted or that frame is discarded due to the receiving STA not implementing the privacy option.
C32 bsnAPIfDot11FailedCount	1.3.6.1.4.1.14179.2.2.6.1.33	Counter32	read-only	This counter shall increment when an MSDU is not transmitted successfully due to the number of transmit attempts exceeding either the bsnAPIfDot11ShortRetryLimit or dot11LongRetryLimit.
bsnAPIfDot11PhyTxPowerTable	1.3.6.1.4.1.14179.2.2.8		not-accessible	Group of attributes for bsnAPIfDot11PhyTxPowerTable. Implemented as a table indexed on STA ID to allow for multiple instances on an Agent. This table has been deprecated. The level and power can be obtained from bsnAPIfTable(bsnAPIfAbsolutePowerList).
bsnAPIfDot11PhyTxPowerEntry	1.3.6.1.4.1.14179.2.2.8.1		not-accessible	An entry in the bsnAPIfDot11PhyTxPower Table. Interface tables in this MIB module are indexed by bsnAPDot3MacAddress, bsnAPIfSlotId.
INT bsnAPIfDot11NumberSupportedPowerLevels	1.3.6.1.4.1.14179.2.2.8.1.1	INTEGER	read-only	The number of power levels supported by the PMD. This attribute can have a value of 1 to 8.
INT bsnAPIfDot11TxPowerLevel1	1.3.6.1.4.1.14179.2.2.8.1.2	INTEGER	read-only	The transmit output power for LEVEL1 in mW. This is also the default power level. It is same as the Maximum power level available on an AP interface.
INT bsnAPIfDot11TxPowerLevel2	1.3.6.1.4.1.14179.2.2.8.1.3	INTEGER	read-only	The transmit output power for LEVEL2 in mW. It is 1/2 of the Maximum power level available on an AP interface.
INT bsnAPIfDot11TxPowerLevel3	1.3.6.1.4.1.14179.2.2.8.1.4	INTEGER	read-only	The transmit output power for LEVEL3 in mW. It is 1/4th of the Maximum power level available on an AP interface.
INT bsnAPIfDot11TxPowerLevel4	1.3.6.1.4.1.14179.2.2.8.1.5	INTEGER	read-only	The transmit output power for LEVEL4 in mW. It is 1/8th of the Maximum power level available on an AP interface.
INT bsnAPIfDot11TxPowerLevel5	1.3.6.1.4.1.14179.2.2.8.1.6	INTEGER	read-only	The transmit output power for LEVEL5 in mW. It is 1/16th of the Maximum power level available on an AP interface.
INT bsnAPIfDot11TxPowerLevel6	1.3.6.1.4.1.14179.2.2.8.1.7	INTEGER	read-only	The transmit output power for LEVEL6 in mW. It is 1/32th of the Maximum power level available on an AP interface.
INT bsnAPIfDot11TxPowerLevel7	1.3.6.1.4.1.14179.2.2.8.1.8	INTEGER	read-only	The transmit output power for LEVEL7 in mW. It is 1/64th of the Maximum power level available on an AP interface.
INT bsnAPIfDot11TxPowerLevel8	1.3.6.1.4.1.14179.2.2.8.1.28	INTEGER	read-only	The transmit output power for LEVEL8 in mW. It is 1/128th of the Maximum power level available on an AP interface.
bsnAPIfDot11PhyChannelTable	1.3.6.1.4.1.14179.2.2.9		not-accessible	Entry of attributes for bsnAPIfDot11PhyChannelEntry. Implemented as a table indexed on bsnAPDot3MacAddress, bsnAPIfSlotId allow for multiple instances on an Agent
bsnAPIfDot11PhyChannelEntry	1.3.6.1.4.1.14179.2.2.9.1		not-accessible	An entry in the bsnAPIfDot11PhyChannelEntry Table. Interface tables in this MIB module are indexed by bsnAPDot3MacAddress, bsnAPIfSlotId.
INT bsnAPIfDot11CurrentCCAMode	1.3.6.1.4.1.14179.2.2.9.1.1	INTEGER	read-only	The current CCA method in operation.Valid values are: energy detect only (edonly) = 01, carrier sense only (csonly) = 02, carrier sense and energy detect (edandcs)= 04 carrier sense with timer (cswithtimer)= 08 high rate carrier sense and energy detect (hrcsanded)=16.
I32 bsnAPIfDot11EDThreshold	1.3.6.1.4.1.14179.2.2.9.1.2	Integer32	read-only	The current Energy Detect Threshold being used by the Channel PHY.
I32 bsnAPIfDot11TIThreshold	1.3.6.1.4.1.14179.2.2.9.1.23	Integer32	read-only	The Threshold being used to detect a busy medium (frequency). CCA shall report a busy medium upon detecting the RSSI above this threshold.
bsnAPIfProfileThresholdConfigTable	1.3.6.1.4.1.14179.2.2.12		not-accessible	Table of attributes for various thresholds to be set on each Airespace AP Interface for Load performance profile , interference performance profile and Noise performance profile.
bsnAPIfProfileThresholdConfigEntry	1.3.6.1.4.1.14179.2.2.12.1		not-accessible	An entry (conceptual row) in the Phy Thresholds Table. Entries in this MIB are indexed by bsnAPDot3MacAddress and bsnAPIfSlotId
INT bsnAPIfProfileParamAssignment	1.3.6.1.4.1.14179.2.2.12.1.1	INTEGER	read-write	If this value is automatic then Profile Parameters in bsnRrmDot11aAPProfile at the global level will be used. If this value is customized then Profile Parameters in bsnAPIfProfileThresholdConfig Table will be used and user can customize them per AP.
INT bsnAPIfForeignInterferenceThreshold	1.3.6.1.4.1.14179.2.2.12.1.2	INTEGER	read-write	foreign interference threshold between 0 and 100 percent.
INT bsnAPIfForeignNoiseThreshold	1.3.6.1.4.1.14179.2.2.12.1.3	INTEGER	read-write	foreign noise threshold between -100 and -50 dBm.
INT bsnAPIfRFUtilizationThreshold	1.3.6.1.4.1.14179.2.2.12.1.4	INTEGER	read-write	RF utlization threshold between 0 and 100 percent.
U32 bsnAPIfThroughputThreshold	1.3.6.1.4.1.14179.2.2.12.1.5	Unsigned32	read-write	Airespace AP data-rate threshold between 1000 and 100000
INT bsnAPIfMobilesThreshold	1.3.6.1.4.1.14179.2.2.12.1.6	INTEGER	read-write	Airespace AP mobiles threshold between 1 and 75
INT bsnAPIfCoverageThreshold	1.3.6.1.4.1.14179.2.2.12.1.7	INTEGER	read-write	Airespace AP coverage threshold between 3 and 50
INT bsnAPIfMobileMinExceptionLevel	1.3.6.1.4.1.14179.2.2.12.1.8	INTEGER	read-write	Airespace AP mobile minimum exception level between 1 and 1000
INT bsnAPIfCoverageExceptionLevel	1.3.6.1.4.1.14179.2.2.12.1.28	INTEGER	read-write	Airespace AP coverage exception level between 0 and 100 percent.
bsnAPIfLoadParametersTable	1.3.6.1.4.1.14179.2.2.13		not-accessible	These are RRM performance related read only parameters per Airespace AP
bsnAPIfLoadParametersEntry	1.3.6.1.4.1.14179.2.2.13.1		not-accessible	An entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress and bsnAPIfSlotId
INT bsnAPIfLoadRxUtilization	1.3.6.1.4.1.14179.2.2.13.1.1	INTEGER	read-only	This is the percentage of time the Airespace AP receiver is busy operating on packets. It is a number from 0-100 representing a load from 0 to 1.
INT bsnAPIfLoadTxUtilization	1.3.6.1.4.1.14179.2.2.13.1.2	INTEGER	read-only	This is the percentage of time the Airespace AP transmitter is busy operating on packets. It is a number from 0-100 representing a load from 0 to 1.
INT bsnAPIfLoadChannelUtilization	1.3.6.1.4.1.14179.2.2.13.1.3	INTEGER	read-only	Channel Utilization
I32 bsnAPIfLoadNumOfClients	1.3.6.1.4.1.14179.2.2.13.1.4	Integer32	read-only	This is the number of clients attached to this Airespace AP at the last measurement interval(This comes from APF)
I32 bsnAPIfPoorSNRClients	1.3.6.1.4.1.14179.2.2.13.1.24	Integer32	read-only	This is the number of clients with poor SNR attached to this Airespace AP at the last measurement interval ( This comes from APF ).
bsnAPIfChannelInterferenceInfoTable	1.3.6.1.4.1.14179.2.2.14		not-accessible	This is a table of channel information like interference and noise from other 802.11 networks on each channel.
bsnAPIfChannelInterferenceInfoEntry	1.3.6.1.4.1.14179.2.2.14.1		not-accessible	An entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress, bsnAPIfSlotId
I32 bsnAPIfInterferenceChannelNo	1.3.6.1.4.1.14179.2.2.14.1.1	Integer32	read-only	Channel Number on AP
I32 bsnAPIfInterferencePower	1.3.6.1.4.1.14179.2.2.14.1.2	Integer32	read-only	Power of Interference from other 802.11 networks on this channel
INT bsnAPIfInterferenceUtilization	1.3.6.1.4.1.14179.2.2.14.1.22	INTEGER	read-only	Interference from other 802.11 networks on this channel
bsnAPIfChannelNoiseInfoTable	1.3.6.1.4.1.14179.2.2.15		not-accessible	This is a table of channel information like interference and noise from other 802.11 networks on each channel.
bsnAPIfChannelNoiseInfoEntry	1.3.6.1.4.1.14179.2.2.15.1		not-accessible	An entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress, bsnAPIfSlotId
I32 bsnAPIfNoiseChannelNo	1.3.6.1.4.1.14179.2.2.15.1.1	Integer32	read-only	Channel Number on AP
I32 bsnAPIfDBNoisePower	1.3.6.1.4.1.14179.2.2.15.1.21	Integer32	read-only	This is the average noise power in dBm on each channel that is available to Airespace AP
bsnAPIfProfileStateTable	1.3.6.1.4.1.14179.2.2.16		not-accessible	This is a table of state of interference monitor on each Airespace AP
bsnAPIfProfileStateEntry	1.3.6.1.4.1.14179.2.2.16.1		not-accessible	An entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress, bsnAPIfSlotId
PRO bsnAPIfLoadProfileState	1.3.6.1.4.1.14179.2.2.16.1.1	ProfileState	read-only	This field represents the current state of the LOAD monitor. This is a total measurement of the business of this Airespace AP. PASS indicates that this Airespace AP is performing adequately compared to the Airespace AP profile. FAIL indicates the Airespace AP is not performing adequately against the LOAD profile.
PRO bsnAPIfInterferenceProfileState	1.3.6.1.4.1.14179.2.2.16.1.2	ProfileState	read-only	This field represents the current state of Interference monitor. This is a total measurement of the interference present at this Airespace AP. PASS indicates that this Airespace AP is performing adequately compared to the Interference profile. FAIL indicates the Airespace AP is not performing adequately against the Interference profile.
PRO bsnAPIfNoiseProfileState	1.3.6.1.4.1.14179.2.2.16.1.3	ProfileState	read-only	This field represents the current state of Noise monitor. This is a total measurement of the noise present at this Airespace AP. PASS indicates that this Airespace AP is performing adequately compared to the noise profile. FAIL indicates the Airespace AP is not performing adequately against the noise profile.
PRO bsnAPIfCoverageProfileState	1.3.6.1.4.1.14179.2.2.16.1.24	ProfileState	read-only	This field represents the current state of coverage monitor. This is a total measurement of the client coverage at this Airespace AP. PASS indicates that this Airespace AP is performing adequately compared to the coverage profile. FAIL indicates the Airespace AP is not performing adequately against the coverage profile.
bsnAPIfRxNeighborsTable	1.3.6.1.4.1.14179.2.2.17		not-accessible	This is a table of Rx Neighbors for each Airespace AP with their RSSI value.
bsnAPIfRxNeighborsEntry	1.3.6.1.4.1.14179.2.2.17.1		not-accessible	An entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress bsnAPIfSlotId, bsnAPIfRxNeighborMacAddress
MAC bsnAPIfRxNeighborMacAddress	1.3.6.1.4.1.14179.2.2.17.1.1	MacAddress	read-only	MAC Address of Rx Neighbor of the Airespace AP
IP bsnAPIfRxNeighborIpAddress	1.3.6.1.4.1.14179.2.2.17.1.2	IpAddress	read-only	IP Address of Rx Neighbor of the Airespace AP
I32 bsnAPIfRxNeighborRSSI	1.3.6.1.4.1.14179.2.2.17.1.3	Integer32	read-only	RSSI value of the Rx Neighbor
I32 bsnAPIfRxNeighborSlot	1.3.6.1.4.1.14179.2.2.17.1.24	Integer32	read-only	Slot value of the Rx Neighbor
I32 bsnAPIfRxNeighborChannel	1.3.6.1.4.1.14179.2.2.17.1.26	Integer32	read-only	This object represents Channel information which neighboring Access point is using.
INT bsnAPIfRxNeighborChannelWidth	1.3.6.1.4.1.14179.2.2.17.1.27	INTEGER	read-only	This object represents Channel bandwidth information which neighboring Access point is using.
bsnAPIfStationRSSICoverageInfoTable	1.3.6.1.4.1.14179.2.2.18		not-accessible	This is a table of channel information like interference and noise from other 802.11 networks on each channel.
bsnAPIfStationRSSICoverageInfoEntry	1.3.6.1.4.1.14179.2.2.18.1		not-accessible	An entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress, bsnAPIfSlotId
I32 bsnAPIfStationRSSICoverageIndex	1.3.6.1.4.1.14179.2.2.18.1.1	Integer32	read-only	RSSI Coverage Index on AP
I32 bsnAPIfRSSILevel	1.3.6.1.4.1.14179.2.2.18.1.2	Integer32	read-only	RSSI Level
I32 bsnAPIfStationCountOnRSSI	1.3.6.1.4.1.14179.2.2.18.1.23	Integer32	read-only	Number of stations on this RSSI Level
bsnAPIfStationSNRCoverageInfoTable	1.3.6.1.4.1.14179.2.2.19		not-accessible	This is a table of Signal to Noise ratio Coverage information on an AP Interface.
bsnAPIfStationSNRCoverageInfoEntry	1.3.6.1.4.1.14179.2.2.19.1		not-accessible	An entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress, bsnAPIfSlotId
I32 bsnAPIfStationSNRCoverageIndex	1.3.6.1.4.1.14179.2.2.19.1.1	Integer32	read-only	SNR Coverage Index on AP
I32 bsnAPIfSNRLevel	1.3.6.1.4.1.14179.2.2.19.1.2	Integer32	read-only	SNR Level
I32 bsnAPIfStationCountOnSNR	1.3.6.1.4.1.14179.2.2.19.1.23	Integer32	read-only	Number of stations on this SNR Level
bsnAPIfRecommendedRFParametersTable	1.3.6.1.4.1.14179.2.2.20		not-accessible	This table list Best Channel,Best TxPowerLevel, Best RTSThreshold,Best FragmentationThreshold etc for this AP Interface as determined by RRM.
bsnAPIfRecommendedRFParametersEntry	1.3.6.1.4.1.14179.2.2.20.1		not-accessible	An entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress, bsnAPIfSlotId
I32 bsnAPIfRecommendedChannelNumber	1.3.6.1.4.1.14179.2.2.20.1.1	Integer32	read-only	Recommended ChannelNumber by RRM for this APIf
I32 bsnAPIfRecommendedTxPowerLevel	1.3.6.1.4.1.14179.2.2.20.1.2	Integer32	read-only	Recommended TxPowerLevel by RRM for this APIf
I32 bsnAPIfRecommendedRTSThreshold	1.3.6.1.4.1.14179.2.2.20.1.3	Integer32	read-only	Recommended RTSThreshold by RRM for this APIf
I32 bsnAPIfRecommendedFragmentationThreshold	1.3.6.1.4.1.14179.2.2.20.1.24	Integer32	read-only	Recommended Fragmentation Threshold by RRM for this APIf
bsnAPIfWlanOverrideTable	1.3.6.1.4.1.14179.2.2.21		not-accessible	Each entry represents an SSID added to the AP when the attribute bsnAPIfWlanOverride on the radio is enabled. This means only those WLANs on the switch that are added to this table will be available on such a radio.
bsnAPIfWlanOverrideEntry	1.3.6.1.4.1.14179.2.2.21.1		not-accessible	An entry in bsnAPIfWlanOverrideTable
U32 bsnAPIfWlanOverrideId	1.3.6.1.4.1.14179.2.2.21.1.1	Unsigned32	read-create	Index of the WLAN (bsnDot11EssIndex) added to the radio. Airespace Switch supports 16 Airespace WLANs so index will be from 1 to 16.
STR bsnAPIfWlanOverrideSsid	1.3.6.1.4.1.14179.2.2.21.1.2	DisplayString	read-only	SSID assigned to the override WLAN.
ROW bsnAPIfWlanOverrideRowStatus	1.3.6.1.4.1.14179.2.2.21.1.15	RowStatus	read-create	A row status type for the bsnAPIfWlanOverrideEntry
bsnMeshNodeTable	1.3.6.1.4.1.14179.2.2.22		not-accessible	This is a table of mesh nodes.
bsnMeshNodeEntry	1.3.6.1.4.1.14179.2.2.22.1		not-accessible	An entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress
INT bsnMeshNodeRole	1.3.6.1.4.1.14179.2.2.22.1.1	INTEGER	read-only	the role of this AP
OCT bsnMeshNodeGroup	1.3.6.1.4.1.14179.2.2.22.1.2	OCTET STRING	read-only	the bridge group name of this AP
INT bsnMeshNodeBackhaul	1.3.6.1.4.1.14179.2.2.22.1.3	INTEGER	read-only	the backhaul radio device for this AP
INT bsnMeshNodeBackhaulPAP	1.3.6.1.4.1.14179.2.2.22.1.4	INTEGER	read-only	the backhaul
INT bsnMeshNodeBackhaulRAP	1.3.6.1.4.1.14179.2.2.22.1.5	INTEGER	read-write	the backhaul radio device for this AP
I32 bsnMeshNodeDataRate	1.3.6.1.4.1.14179.2.2.22.1.6	Integer32	read-write	this nodes backhaul data rate
I32 bsnMeshNodeChannel	1.3.6.1.4.1.14179.2.2.22.1.7	Integer32	read-only	this nodes backhaul channel
INT bsnMeshNodeRoutingState	1.3.6.1.4.1.14179.2.2.22.1.8	INTEGER	read-only	routing state
C32 bsnMeshNodeMalformedNeighPackets	1.3.6.1.4.1.14179.2.2.22.1.9	Counter32	read-only	the number of malformed neighbor packets.
C32 bsnMeshNodePoorNeighSnr	1.3.6.1.4.1.14179.2.2.22.1.10	Counter32	read-only	poor neighbor snr
C32 bsnMeshNodeBlacklistPackets	1.3.6.1.4.1.14179.2.2.22.1.11	Counter32	read-only	the number of blacklist packets received
C32 bsnMeshNodeInsufficientMemory	1.3.6.1.4.1.14179.2.2.22.1.12	Counter32	read-only	occurences of insufficient memory conditions
C32 bsnMeshNodeRxNeighReq	1.3.6.1.4.1.14179.2.2.22.1.13	Counter32	read-only	Rx neighbor requests
C32 bsnMeshNodeRxNeighRsp	1.3.6.1.4.1.14179.2.2.22.1.14	Counter32	read-only	Rx neighbor responses
C32 bsnMeshNodeTxNeighReq	1.3.6.1.4.1.14179.2.2.22.1.15	Counter32	read-only	Tx neighbor requests
C32 bsnMeshNodeTxNeighRsp	1.3.6.1.4.1.14179.2.2.22.1.16	Counter32	read-only	Tx neighbor responses
C32 bsnMeshNodeParentChanges	1.3.6.1.4.1.14179.2.2.22.1.17	Counter32	read-only	number of parent changes
C32 bsnMeshNodeNeighTimeout	1.3.6.1.4.1.14179.2.2.22.1.18	Counter32	read-only	number of neighbor timeouts
MAC bsnMeshNodeParentMacAddress	1.3.6.1.4.1.14179.2.2.22.1.19	MacAddress	read-only	parents mac addressed
INT bsnMeshNodeAPType	1.3.6.1.4.1.14179.2.2.22.1.20	INTEGER	read-only	the type of AP
INT bsnMeshNodeEthernetBridge	1.3.6.1.4.1.14179.2.2.22.1.21	INTEGER	read-write	enable : Enables ethernet bridging on the AP. disable : Disables ethernet bridging on the AP. Changes are only applicable when AP is in 'Bridge' mode.
I32 bsnMeshNodeHops	1.3.6.1.4.1.14179.2.2.22.1.30	Integer32	read-only	number of hops to rap
bsnMeshNeighsTable	1.3.6.1.4.1.14179.2.2.23		not-accessible	This is a table of mesh neighbors.
bsnMeshNeighsEntry	1.3.6.1.4.1.14179.2.2.23.1		not-accessible	An entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress and bsnMeshNeighNeighMacAddress
MAC bsnMeshNeighMacAddress	1.3.6.1.4.1.14179.2.2.23.1.1	MacAddress	read-only	MAC Address of neighbor
INT bsnMeshNeighType	1.3.6.1.4.1.14179.2.2.23.1.2	INTEGER	read-only	neighbor type
INT bsnMeshNeighState	1.3.6.1.4.1.14179.2.2.23.1.3	INTEGER	read-only	neighbor state
I32 bsnMeshNeighSnr	1.3.6.1.4.1.14179.2.2.23.1.4	Integer32	read-only	explicitly set SNR
I32 bsnMeshNeighSnrUp	1.3.6.1.4.1.14179.2.2.23.1.5	Integer32	read-only	snr up
I32 bsnMeshNeighSnrDown	1.3.6.1.4.1.14179.2.2.23.1.6	Integer32	read-only	snr down
I32 bsnMeshNeighLinkSnr	1.3.6.1.4.1.14179.2.2.23.1.7	Integer32	read-only	link snr
I32 bsnMeshNeighAdjustedEase	1.3.6.1.4.1.14179.2.2.23.1.8	Integer32	read-only	hops adjusted ease
I32 bsnMeshNeighUnadjustedEase	1.3.6.1.4.1.14179.2.2.23.1.9	Integer32	read-only	ease to root AP from this AP
I32 bsnMeshNeighRapEase	1.3.6.1.4.1.14179.2.2.23.1.10	Integer32	read-only	unadjusted ease received in last hello
C32 bsnMeshNeighTxParent	1.3.6.1.4.1.14179.2.2.23.1.11	Counter32	read-only	tx packets to this node while a parent
C32 bsnMeshNeighRxParent	1.3.6.1.4.1.14179.2.2.23.1.12	Counter32	read-only	rx packets from this node while a parent
C32 bsnMeshNeighPoorSnr	1.3.6.1.4.1.14179.2.2.23.1.13	Counter32	read-only	packets with poor snr received from this node
I32 bsnMeshNeighLastUpdate	1.3.6.1.4.1.14179.2.2.23.1.14	Integer32	read-only	last received hello from this neighbor
I32 bsnMeshNeighParentChange	1.3.6.1.4.1.14179.2.2.23.1.20	Integer32	read-only	when this node last became parent
bsnAPIfRadarChannelStatisticsTable	1.3.6.1.4.1.14179.2.2.24		not-accessible	This is a table of channel information on which radar signal were detected. This will give the list of channels and last heard timestamp. Radar signals are detected only on 5Ghz range. So this will be detected for 802.11a interface.
bsnAPIfRadarChannelStatisticsEntry	1.3.6.1.4.1.14179.2.2.24.1		not-accessible	An entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress, bsnAPIfSlotId, bsnAPIfRadarDetectedCannelNumber.
I32 bsnAPIfRadarDetectedChannelNumber	1.3.6.1.4.1.14179.2.2.24.1.1	Integer32	read-only	Channel Number on which radar signals were detected.
I32 bsnAPIfRadarSignalLastHeard	1.3.6.1.4.1.14179.2.2.24.1.2	Integer32	read-only	This tells how many seconds ago radar signal was heard on the channel.
bsnGlobalDot11	1.3.6.1.4.1.14179.2.3
bsnGlobalDot11Config	1.3.6.1.4.1.14179.2.3.1
INT bsnGlobalDot11PrivacyOptionImplemented	1.3.6.1.4.1.14179.2.3.1.1	INTEGER	read-only	This attribute, when true, shall indicate that the IEEE 802.11 WEP option is implemented. The default value of this attribute shall be false.
U32 bsnGlobalDot11AuthenticationResponseTimeOut	1.3.6.1.4.1.14179.2.3.1.2	Unsigned32	read-write	This attribute shall specify the number of TU that a responding STA should wait for the next frame in the authentication sequence.
INT bsnGlobalDot11MultiDomainCapabilityImplemented	1.3.6.1.4.1.14179.2.3.1.3	INTEGER	read-only	This attribute, when TRUE, indicates that the station implementation is capable of supporting multiple regulatory domains. The capability is disabled, otherwise. The default value of this attribute is FALSE.
INT bsnGlobalDot11MultiDomainCapabilityEnabled	1.3.6.1.4.1.14179.2.3.1.4	INTEGER	read-only	This attribute, when TRUE, indicates that the capability of the station to operate in multiple regulatory domains is enabled. The capability is disabled, otherwise. The default value of this attribute is FALSE.
INT bsnGlobalDot11CountryIndex	1.3.6.1.4.1.14179.2.3.1.5	INTEGER	read-write	This attribute identifies the country in which the station is operating.
INT bsnGlobalDot11LoadBalancing	1.3.6.1.4.1.14179.2.3.1.6	INTEGER	read-write	This attribute specifies if load balancing of clients is enabled on disabled. Global configuration of Load Balancing is now removed. Use cLWlanLoadBalancingEnable to configure it per WLAN.
I32 bsnGlobalDot11RogueTimer	1.3.6.1.4.1.14179.2.3.1.7	Integer32	read-write	This attribute specifies in seconds, the time interval after which a Rogue Entry in Rogue Table will expire if no beacon is heard from a Rogue.
INT bsnPrimaryMwarForAPs	1.3.6.1.4.1.14179.2.3.1.8	INTEGER	read-write	This attribute specifies if this Switch acts a Master Switch for the Airespace APs. So if an Airespace AP doesn't find its Primary Switch, it will associate with this Switch.
INT bsnRtpProtocolPriority	1.3.6.1.4.1.14179.2.3.1.9	INTEGER	read-write	Real Time Protocol Priority.
STR bsnSystemCurrentTime	1.3.6.1.4.1.14179.2.3.1.10	DisplayString	read-only	This attribute will display the Current System time on the Switch.
STR bsnUpdateSystemTime	1.3.6.1.4.1.14179.2.3.1.11	DisplayString	read-write	Use this attribute to change the System time on the Switch. Specify the new time in this Format MM/DD/YYYY HH:MM:SS
INT bsnOperatingTemperatureEnvironment	1.3.6.1.4.1.14179.2.3.1.12	INTEGER	read-only	Operating Environment of the Airespace Switch. commercial is Commercial (0 to 40 C) and industrial is Industrial (-10 to 70 C)
I32 bsnSensorTemperature	1.3.6.1.4.1.14179.2.3.1.13	Integer32	read-only	Current Internal Temperature of the unit in Centigrade
I32 bsnTemperatureAlarmLowLimit	1.3.6.1.4.1.14179.2.3.1.14	Integer32	read-only	Internal Temperature Alarm Low Limit in Centigrade. If the bsnSensorTemperature goes below this limit bsnSensedTemperatureTooLow Alarm will be sent out
I32 bsnTemperatureAlarmHighLimit	1.3.6.1.4.1.14179.2.3.1.15	Integer32	read-only	Internal Temperature Alarm High Limit in Centigrade. If the bsnSensorTemperature goes above this limit bsnSensedTemperatureTooHigh Alarm will be sent out
IP bsnVirtualGatewayAddress	1.3.6.1.4.1.14179.2.3.1.16	IpAddress	read-write	Virtual Gateway Address of the Switch. This is used by web auth and Ipsec. If the virtual IP Address is changed, the Switch has to be rebooted for the new Address to take effect. This is now replaced by the Virtual Interface in bsnswitching MIB.
OCT bsnRFMobilityDomainName	1.3.6.1.4.1.14179.2.3.1.17	OCTET STRING	read-write	RF Mobility Group Name to which this Airespace Switch belongs. Airespace Switches on a network form a RF Group as well as a Mobility Group. RF Groups does the channel and power management of AP while Mobility Group does load balancing and hand off for clients.
INT bsnClientWatchListFeature	1.3.6.1.4.1.14179.2.3.1.18	INTEGER	read-write	This flag should be turned on for the client watch lists to be enabled on the switch. When enabled, the switch generates Client Association and Authentication traps for the watchlisted clients.
INT bsnRogueLocationDiscoveryProtocol	1.3.6.1.4.1.14179.2.3.1.19	INTEGER	read-write	This flag should be turned on to enable the Rogue Location Discovery Protocol feature on the switch. We can either enable this feature for all the APs or only for APs in monitor mode.
INT bsnRogueAutoContainFeature	1.3.6.1.4.1.14179.2.3.1.20	INTEGER	read-write	This flag should be turned on to allow the switch to contain the rogues automatically if detected on the wired network.
INT bsnOverAirProvisionApMode	1.3.6.1.4.1.14179.2.3.1.21	INTEGER	read-write	Over the Air Provisioning Mode for APs
I32 bsnMaximumNumberOfConcurrentLogins	1.3.6.1.4.1.14179.2.3.1.22	Integer32	read-write	This attribute specifies the maximum number of concurrent logins that the switch will allow for a single user. A value 0 implies that there is no restriction on the number of concurrent logins with a single username.
INT bsnAutoContainRoguesAdvertisingSsid	1.3.6.1.4.1.14179.2.3.1.23	INTEGER	read-write	This flag should be set to 1 to allow the switch to contain automatically those rogues that are advertising our SSID. If value is 0, only an alarm will be generated when such a rogue is detected.
INT bsnAutoContainAdhocNetworks	1.3.6.1.4.1.14179.2.3.1.24	INTEGER	read-write	This flag should be set to 1 to allow the switch to contain automatically the adhoc networks detected by the switch. If value is 0, only an alarm will be generated when such a network is detected.
INT bsnAutoContainTrustedClientsOnRogueAps	1.3.6.1.4.1.14179.2.3.1.25	INTEGER	read-write	This flag should be set to 1 to allow the switch to contain automatically those trusted clients that are associated to rogue APs. If value is 0, only an alarm will be generated when such a client is detected.
INT bsnValidateRogueClientsAgainstAAA	1.3.6.1.4.1.14179.2.3.1.26	INTEGER	read-write	This flag should be turned on to allow the switch to validate 'valid' mobiles associating with rogue APs. For example, if a client's MAC Address is found in the local MAC filter table, that client can be validated.
I32 bsnSystemTimezoneDelta	1.3.6.1.4.1.14179.2.3.1.27	Integer32	read-write	The delta (difference) between the local time and the Universal Coordinated Time in hours. For example, it is -8 for the PST and +1 for France. If the delta is -5.30 then this attribute will store -5 and bsnSystemTimezoneDeltaMinutes will store 30. This value i should be between -23 to +23
INT bsnSystemTimezoneDaylightSavings	1.3.6.1.4.1.14179.2.3.1.28	INTEGER	read-write	This flag specifies if daylight savings are enabled for the current timezone.
INT bsnAllowAuthorizeApAgainstAAA	1.3.6.1.4.1.14179.2.3.1.29	INTEGER	read-write	This flag specifies if LWAPP is allowed to get authorization via RADIUS or local database for an AP.
I32 bsnSystemTimezoneDeltaMinutes	1.3.6.1.4.1.14179.2.3.1.30	Integer32	read-write	The minutes component of delta (difference) between the local time and the Universal Coordinated Time.
INT bsnApFallbackEnabled	1.3.6.1.4.1.14179.2.3.1.31	INTEGER	read-write	This flag specifies if the APs should continue LWAPP discoveries to fallback to the primary switch in case they are not already associated with it i.e they are associated with their respective secondary or tertiary switch instead.
INT bsnAppleTalkEnabled	1.3.6.1.4.1.14179.2.3.1.32	INTEGER	read-write	This flag turns on the appletalk bridging in the switch such that the packets from Apple clients that use appletalk format can be processed by the switch. When this flag is off, these packets are dropped.
bsnTrustedApPolicyConfig	1.3.6.1.4.1.14179.2.3.1.40
INT bsnPolicyForMisconfiguredAps	1.3.6.1.4.1.14179.2.3.1.40.1	INTEGER	read-write	This flag should be turned on to allow the switch to contain misconfigured APs.
INT bsnEncryptionPolicyEnforced	1.3.6.1.4.1.14179.2.3.1.40.2	INTEGER	read-write	The encryption policy that is enforced on the trusted APs.
INT bsnPreamblePolicyEnforced	1.3.6.1.4.1.14179.2.3.1.40.3	INTEGER	read-write	The preamble policy that is enforced on the trusted APs.
INT bsnDot11ModePolicyEnforced	1.3.6.1.4.1.14179.2.3.1.40.4	INTEGER	read-write	The 802.11 Mode policy that is enforced on the trusted APs.
INT bsnRadioTypePolicyEnforced	1.3.6.1.4.1.14179.2.3.1.40.5	INTEGER	read-write	The radio type policy that is enforced on the trusted APs.
INT bsnValidateSsidForTrustedAp	1.3.6.1.4.1.14179.2.3.1.40.6	INTEGER	read-write	If enabled, the SSID of trusted APs will be validated by the switch.
INT bsnAlertIfTrustedApMissing	1.3.6.1.4.1.14179.2.3.1.40.7	INTEGER	read-write	If enabled, an alert will be generated when a trusted AP is missing.
I32 bsnTrustedApEntryExpirationTimeout	1.3.6.1.4.1.14179.2.3.1.40.8	Integer32	read-write	This attribute specifies in seconds, the time interval after which a Trusted AP Entry will expire if no beacon is heard from that AP.
bsnClientExclusionPolicyConfig	1.3.6.1.4.1.14179.2.3.1.41
INT bsnExcessive80211AssocFailures	1.3.6.1.4.1.14179.2.3.1.41.1	INTEGER	read-write	This flag specifies if client should be excluded (blacklisted) if repeated 802.11 Association Failures occurs with a client.
INT bsnExcessive80211AuthFailures	1.3.6.1.4.1.14179.2.3.1.41.2	INTEGER	read-write	This flag specifies if client should be excluded (blacklisted) if repeated 802.11 Authentication Failures occurs with a client.
INT bsnExcessive8021xAuthFailures	1.3.6.1.4.1.14179.2.3.1.41.3	INTEGER	read-write	This flag specifies if client should be excluded (blacklisted) if repeated 802.1x Authentication Failures occurs with a client.
INT bsnExternalPolicyServerFailures	1.3.6.1.4.1.14179.2.3.1.41.4	INTEGER	read-write	This flag specifies if client should be excluded (blacklisted) if repeated external policy server failures occurs with a client.
INT bsnExcessiveWebAuthFailures	1.3.6.1.4.1.14179.2.3.1.41.5	INTEGER	read-write	This flag specifies if client should be excluded (blacklisted) if repeated Web Authentication Failures occurs with a client.
INT bsnIPTheftORReuse	1.3.6.1.4.1.14179.2.3.1.41.6	INTEGER	read-write	This flag specifies if client should be excluded (blacklisted) if it appears to be reusing an IP Address.(Possible IP Theft)
bsnSignatureConfig	1.3.6.1.4.1.14179.2.3.1.42
bsnStandardSignatureTable	1.3.6.1.4.1.14179.2.3.1.42.1		not-accessible	The table listing Standard Signatures configured on the switch. The standard signatures are provided with the released product. The standard signatures can be updated via file download to the switch. The table is indexed by the precedence of the signatures.
bsnStandardSignatureEntry	1.3.6.1.4.1.14179.2.3.1.42.1.1		not-accessible	....
U32 bsnStandardSignaturePrecedence	1.3.6.1.4.1.14179.2.3.1.42.1.1.1	Unsigned32	read-only	Precedence of the signature. This specifies the order in which the signature is applied to a packet.
STR bsnStandardSignatureName	1.3.6.1.4.1.14179.2.3.1.42.1.1.2	DisplayString	read-only	This attribute is used to configure the name on a signature.
STR bsnStandardSignatureDescription	1.3.6.1.4.1.14179.2.3.1.42.1.1.3	DisplayString	read-only	This attribute is used to configure the description of a signature.
INT bsnStandardSignatureFrameType	1.3.6.1.4.1.14179.2.3.1.42.1.1.4	INTEGER	read-only	This attribute specifies the type of frame that needs to match a signature.
INT bsnStandardSignatureAction	1.3.6.1.4.1.14179.2.3.1.42.1.1.5	INTEGER	read-only	This attribute specifies the action to be taken once a packet is found to match a signature.
INT bsnStandardSignatureState	1.3.6.1.4.1.14179.2.3.1.42.1.1.6	INTEGER	read-only	This attribute specifies the state of a signature. It is used to match packets only if the state is enabled.
U32 bsnStandardSignatureFrequency	1.3.6.1.4.1.14179.2.3.1.42.1.1.7	Unsigned32	read-write	This specifies the frequency of the matching packets after which the specified action is taken.
U32 bsnStandardSignatureQuietTime	1.3.6.1.4.1.14179.2.3.1.42.1.1.8	Unsigned32	read-write	This specifies the quiet time in seconds during which no matching packets are found after which the attack is considered stopped.
U32 bsnStandardSignatureVersion	1.3.6.1.4.1.14179.2.3.1.42.1.1.9	Unsigned32	read-only	This specifies the signature version.
INT bsnStandardSignatureConfigType	1.3.6.1.4.1.14179.2.3.1.42.1.1.10	INTEGER	read-only	This attribute specifies the type of Signature configuration. It's protocol when the protocol format is used in the UI to configure this. Pattern is the config type for all signatures in the released signature file and when signatures are configured using pattern format. Note: the signatures will be allowed to be i configured in later releases.
T/F bsnStandardSignatureEnable	1.3.6.1.4.1.14179.2.3.1.42.1.1.11	TruthValue	read-write	This object configures the status of a particular standard signature on LWAPP APs, for use in performing signature analysis on the received 802.11 data and/or management frames. A value of 'true' makes the Controller send the 'Signature Add LWAPP Message' to all the joined APs with the status field set to 'enable'. This makes the joined APs perform signature analysis on the received 802.11 data and/or management frames and report the discrepancies observed, if any, to the Controller. A value of 'false' makes the Controller send the 'Signature Add LWAPP Message' to all the joined APs with the status field set to 'disable'. The joined APs doesn't perform the signature analysis on the received 802.11 data and/or management frames for this particular signature, till the signature is enabled.
BSN bsnStandardSignatureMacInfo	1.3.6.1.4.1.14179.2.3.1.42.1.1.12	BsnTxtSignatureMacInfo	read-only	This object defines the pattern followed by the LWAPP APs to perform signature analysis with this Standard signature and report the results to the Controller.
U32 bsnStandardSignatureMacFreq	1.3.6.1.4.1.14179.2.3.1.42.1.1.13	Unsigned32	read-write	This object specifies the frequency of matching packets from a particular source after which the specified action is taken.
ROW bsnStandardSignatureRowStatus	1.3.6.1.4.1.14179.2.3.1.42.1.1.20	RowStatus	read-only	Row Status for creation/deletion. Signature will allowed to be created, deleted and edited in later releases.
U32 bsnStandardSignatureInterval	1.3.6.1.4.1.14179.2.3.1.42.1.1.21	Unsigned32	read-write	Interval of the signature. This specifies the interval when the signature is applied to a packet.
bsnStandardSignaturePatternTable	1.3.6.1.4.1.14179.2.3.1.42.2		not-accessible	The table listing the matching patterns specified for a i Standard Signature. These are instrumental in matching the signature with a packet. A maximum of 5 i patterns may be specifed for a signature. These are used for matching in the order of their index.
bsnStandardSignaturePatternEntry	1.3.6.1.4.1.14179.2.3.1.42.2.1		not-accessible	....
U32 bsnStandardSignaturePatternIndex	1.3.6.1.4.1.14179.2.3.1.42.2.1.1	Unsigned32	read-only	Index of the pattern. This specifies the order in which the pattern is checked against the packet contents.
U32 bsnStandardSignaturePatternOffset	1.3.6.1.4.1.14179.2.3.1.42.2.1.2	Unsigned32	read-only	Offset from the start of the packet where the AP looks for a match to the pattern.
STR bsnStandardSignaturePatternString	1.3.6.1.4.1.14179.2.3.1.42.2.1.3	DisplayString	read-only	This is the pattern string that the AP uses to match at the offset. Example: 0x616c7068615f3178
STR bsnStandardSignaturePatternMask	1.3.6.1.4.1.14179.2.3.1.42.2.1.4	DisplayString	read-only	This is the pattern mask. This is the bit mask that the AP uses to mask out the bits in the packet at the given offset. Example: 0xffffffffffffffff
BSN bsnStandardSignaturePatternOffSetStart	1.3.6.1.4.1.14179.2.3.1.42.2.1.5	BsnSignaturePatternOffSetStart	read-only	This object indicates how an offset should be applied while doing signature analysis for QOS and non-QOS data frames with this standard signature.
ROW bsnStandardSignaturePatternRowStatus	1.3.6.1.4.1.14179.2.3.1.42.2.1.15	RowStatus	read-only	Row Status for creation/deletion. Signature Pattern will allowed to be created, deleted and edited in later releases.
bsnCustomSignatureTable	1.3.6.1.4.1.14179.2.3.1.42.3		not-accessible	The table listing Standard Signatures configured on the switch. The standard signatures are provided with the released product. The standard signatures can be updated via file download to the switch. The table is indexed by the precedence of the signatures.
bsnCustomSignatureEntry	1.3.6.1.4.1.14179.2.3.1.42.3.1		not-accessible	....
U32 bsnCustomSignaturePrecedence	1.3.6.1.4.1.14179.2.3.1.42.3.1.1	Unsigned32	read-only	Precedence of the signature. This specifies the order in which the signature is applied to a packet.
STR bsnCustomSignatureName	1.3.6.1.4.1.14179.2.3.1.42.3.1.2	DisplayString	read-only	This attribute is used to configure the name on a signature.
STR bsnCustomSignatureDescription	1.3.6.1.4.1.14179.2.3.1.42.3.1.3	DisplayString	read-only	This attribute is used to configure the description of a signature.
INT bsnCustomSignatureFrameType	1.3.6.1.4.1.14179.2.3.1.42.3.1.4	INTEGER	read-only	This attribute specifies the type of frame that needs to match a signature.
INT bsnCustomSignatureAction	1.3.6.1.4.1.14179.2.3.1.42.3.1.5	INTEGER	read-only	This attribute specifies the action to be taken once a packet is found to match a signature.
INT bsnCustomSignatureState	1.3.6.1.4.1.14179.2.3.1.42.3.1.6	INTEGER	read-only	This attribute specifies the state of a signature. It is used to match packets only if the state is enabled.
U32 bsnCustomSignatureFrequency	1.3.6.1.4.1.14179.2.3.1.42.3.1.7	Unsigned32	read-write	This specifies the frequency of the matching packets after which the specified action is taken.
U32 bsnCustomSignatureQuietTime	1.3.6.1.4.1.14179.2.3.1.42.3.1.8	Unsigned32	read-write	This specifies the quiet time in seconds during which no matching packets are found after which the attack is considered stopped.
U32 bsnCustomSignatureVersion	1.3.6.1.4.1.14179.2.3.1.42.3.1.9	Unsigned32	read-only	This specifies the signature version.
INT bsnCustomSignatureConfigType	1.3.6.1.4.1.14179.2.3.1.42.3.1.10	INTEGER	read-only	This attribute specifies the type of Signature configuration. It's protocol when the protocol format is used in the UI to configure this. Pattern is the config type for all signatures in the released signature file and when signatures are configured using pattern format. Note: the signatures will be allowed to be configured in later releases.
T/F bsnCustomSignatureEnable	1.3.6.1.4.1.14179.2.3.1.42.3.1.11	TruthValue	read-write	This object configures the status of a particular Custom signature on LWAPP APs, for use in performing signature analysis on the received 802.11 data and/or management frames. A value of 'true' makes the Controller send the 'Signature Add LWAPP Message' to all the joined APs with the status field set to 'enable'. This makes the joined APs perform signature analysis on the received 802.11 data and/or management frames and report the discrepancies observed, if any, to the Controller. A value of 'false' makes the Controller send the 'Signature Add LWAPP Message' to all the joined APs with the status field set to 'disable'. The joined APs doesn't perform the signature analysis on the received 802.11 data and/or management frames for this particular signature, till the signature is enabled.
BSN bsnCustomSignatureMacInfo	1.3.6.1.4.1.14179.2.3.1.42.3.1.12	BsnTxtSignatureMacInfo	read-only	This object defines the pattern followed by the LWAPP APs to perform signature analysis with this Custom signature and report the results to the Controller.
U32 bsnCustomSignatureMacFreq	1.3.6.1.4.1.14179.2.3.1.42.3.1.13	Unsigned32	read-write	This object specifies the frequency of matching packets from a particular source after which the specified action is taken.
ROW bsnCustomSignatureRowStatus	1.3.6.1.4.1.14179.2.3.1.42.3.1.20	RowStatus	read-only	Row Status for creation/deletion. Signature will allowed to be created, deleted and edited in later releases.
U32 bsnCustomSignatureInterval	1.3.6.1.4.1.14179.2.3.1.42.3.1.21	Unsigned32	read-write	Interval of the signature. This specifies the interval when the signature is applied to a packet.
bsnCustomSignaturePatternTable	1.3.6.1.4.1.14179.2.3.1.42.4		not-accessible	The table listing the matching patterns specified for a Standard Signature. These are instrumental in matching the signature with a packet. A maximum of 5 patterns may be specifed for a signature. These are used for matching in the order of their index.
bsnCustomSignaturePatternEntry	1.3.6.1.4.1.14179.2.3.1.42.4.1		not-accessible	....
U32 bsnCustomSignaturePatternIndex	1.3.6.1.4.1.14179.2.3.1.42.4.1.1	Unsigned32	read-only	Index of the pattern. This specifies the order in which the pattern is checked against the packet contents.
U32 bsnCustomSignaturePatternOffset	1.3.6.1.4.1.14179.2.3.1.42.4.1.2	Unsigned32	read-only	Offset from the start of the packet where the AP looks for a match to the pattern.
STR bsnCustomSignaturePatternString	1.3.6.1.4.1.14179.2.3.1.42.4.1.3	DisplayString	read-only	This is the pattern string that the AP uses to match at the offset. Example: 0x616c7068615f3178
STR bsnCustomSignaturePatternMask	1.3.6.1.4.1.14179.2.3.1.42.4.1.4	DisplayString	read-only	This is the pattern mask. This is the bit mask that the AP uses to mask out the bits in the packet at the given offset. Example: 0xffffffffffffffff
BSN bsnCustomSignaturePatternOffSetStart	1.3.6.1.4.1.14179.2.3.1.42.4.1.5	BsnSignaturePatternOffSetStart	read-only	This object indicates how an offset should be applied while doing signature analysis for QOS and non-QOS data frames with this custom signature.
ROW bsnCustomSignaturePatternRowStatus	1.3.6.1.4.1.14179.2.3.1.42.4.1.15	RowStatus	read-only	Row Status for creation/deletion. Signature Pattern will allowed to be created, deleted and edited in later releases.
INT bsnSignatureCheckState	1.3.6.1.4.1.14179.2.3.1.42.5	INTEGER	read-write	This flag should be enabled to enforce check of all standard and custom signatures. If disabled, there will be no check for signatures, both custom and standard, by the switch.
bsnRfIdTagConfig	1.3.6.1.4.1.14179.2.3.1.43
INT bsnRfIdTagStatus	1.3.6.1.4.1.14179.2.3.1.43.1	INTEGER	read-write	This flag should be turned on to allow the switch to collect data for tags.
U32 bsnRfIdTagDataTimeout	1.3.6.1.4.1.14179.2.3.1.43.2	Unsigned32	read-write	This is the number of seconds after which the tag data is deleted by the switch from its database if it didn't hear from the tag again.
INT bsnRfIdTagAutoTimeoutStatus	1.3.6.1.4.1.14179.2.3.1.43.3	INTEGER	read-write	This flag should be turned on to allow auto deletion of tag data in the switch after expiration of Tag Data Timeout
bsnAPNeighborAuthConfig	1.3.6.1.4.1.14179.2.3.1.44
INT bsnAPNeighborAuthStatus	1.3.6.1.4.1.14179.2.3.1.44.1	INTEGER	read-write	This flag should be turned on to allow the AP-Neighbor Authentication feature.
INT bsnAPNeighborAuthAlarmThreshold	1.3.6.1.4.1.14179.2.3.1.44.2	INTEGER	read-write	Authentication alarm trigger threshold.
OCT bsnRFNetworkName	1.3.6.1.4.1.14179.2.3.1.45	OCTET STRING	read-write	RF Network Group Name to which this Airespace Switch belongs. Airespace Switches on a network form a RF Network Group as well as a Mobility Group. RF Network Groups does the channel and power management of AP while Mobility Group does load balancing and hand off for clients.
INT bsnFastSSIDChangeFeature	1.3.6.1.4.1.14179.2.3.1.46	INTEGER	read-write	Configures Fast SSID changing feature for mobile-stations. When enabled, permits mobile-stations to change SSIDs without having to block and wait for SSID-cleanup on the switch to occur.
bsnBridgingPolicyConfig	1.3.6.1.4.1.14179.2.3.1.47
INT bsnBridgingZeroTouchConfig	1.3.6.1.4.1.14179.2.3.1.47.1	INTEGER	read-write	If enabled, allows new bridging APs to negotiate with the switch to acquire the shared secret key.
OCT bsnBridgingSharedSecretKey	1.3.6.1.4.1.14179.2.3.1.47.2	OCTET STRING	read-write	Key that is used to negotiate a secure LWAPP connection between a switch and a bridging or mesh AP.
INT bsnAcceptSelfSignedCertificate	1.3.6.1.4.1.14179.2.3.1.48	INTEGER	read-write	This flag specifies if controller will accept Self Signed Certificate from AP as part of authorization.
U32 bsnSystemClockTime	1.3.6.1.4.1.14179.2.3.1.49	Unsigned32	read-only	This object represents the current clock time of the controller and expressed as the number of seconds elapsed since 00:00:00 on January 1, 1970, Coordinated Universal Time (UTC).
bsnGlobalDot11b	1.3.6.1.4.1.14179.2.3.2
bsnGlobalDot11bConfig	1.3.6.1.4.1.14179.2.3.2.1
INT bsnGlobalDot11bNetworkStatus	1.3.6.1.4.1.14179.2.3.2.1.1	INTEGER	read-write	802.11b Network Admin Status.
INT bsnGlobalDot11bBeaconPeriod	1.3.6.1.4.1.14179.2.3.2.1.2	INTEGER	read-write	This attribute shall specify the number of TU that a AP Radio shall use for scheduling Beacon tranmissions. This value is transmitted in Beacon and Probe Response frames.
INT bsnGlobalDot11bDynamicChannelAssignment	1.3.6.1.4.1.14179.2.3.2.1.3	INTEGER	read-write	Dynamic channel assignment(DCA) has three modes. When the mode is auto, the channel assignment will be periodically updated for all Airespace APs that permit this operation. When the DCA is runOnce, channel assignments are updated based on the UPDATE_CMD received from the management. When the DCA is static, no dynamic channel assignments occurs and value are set to their global default. Default is auto.
INT bsnGlobalDot11bCurrentChannel	1.3.6.1.4.1.14179.2.3.2.1.4	INTEGER	read-write	The current operating frequency channel of the DSSS PHY. Valid channel numbers are as defined in 15.4.6.2. This attribute will be read-only if bsnAPIfPhyChannelAutomaticOn is true.
U32 bsnGlobalDot11bDynamicChannelUpdateInterval	1.3.6.1.4.1.14179.2.3.2.1.5	Unsigned32	read-only	When Channel dynamic alogirthm is running, this interval (in secs) specifies how often Channel assignement updates are attempted on an Airespace AP. NOTE: hysteresis is built into the algorithms so we will not have uproductive changes occuring. Default value is 600 secs
U32 bsnGlobalDot11bInputsForDCA	1.3.6.1.4.1.14179.2.3.2.1.6	Unsigned32	read-write	This attribute is a bit mask specifying what to include in DCA optimization.Below is a list of parameters and their corresponding bits identifiers. options bit -------------------------------------- none 0 SIGNAL STRENGTH 1 NOISE 2 FOREIGN INTERFERENCE 4 LOAD 8 DEVICE INTERFERENCE 32 Default value is 63( all bits on).
INT bsnGlobalDot11bChannelUpdateCmdInvoke	1.3.6.1.4.1.14179.2.3.2.1.7	INTEGER	read-write	When set to activate this starts a DCA calculation regardless of the dynamic update interval. This command should be invoke on Group Leader Airespace Switch.Invoking on a Airespace Switch which is not a Group leader has no effect.
I32 bsnGlobalDot11bChannelUpdateCmdStatus	1.3.6.1.4.1.14179.2.3.2.1.8	Integer32	read-only	After setting bsnGlobalDot11bChannelUpdateCmdInvoke to activate, the result of action can be monitored from here. It takes 5 minutes for the command to complete.
INT bsnGlobalDot11bDynamicTransmitPowerControl	1.3.6.1.4.1.14179.2.3.2.1.9	INTEGER	read-write	Dynamic transmit power (DTP) has three modes. When the mode is auto, the transmit power of each Airespace AP will be periodically updated for all Airespace APs that permit this operation. When the DTP is runOnce,transmit power update will occur based on the UPDATE_CMD received from the management. When the DTP is static, no dynamic transmit power updates occur and their global defaults are used. Default is auto.
U32 bsnGlobalDot11bDynamicTxPowerControlInterval	1.3.6.1.4.1.14179.2.3.2.1.10	Unsigned32	read-only	When Tx PowerControl dynamic alogirthm is running, this interval(in secs) specifies how often TxPower control updates are attempted on an Airespace AP. NOTE: hysteresis is build into the algorithms so we will not have uproductive changes occuring. Default value is 600 secs
INT bsnGlobalDot11bCurrentTxPowerLevel	1.3.6.1.4.1.14179.2.3.2.1.11	INTEGER	read-write	The TxPowerLevel N currently being used to transmit data. Some PHYs also use this value to determine the receiver sensitivity requirements for CCA.
U32 bsnGlobalDot11bInputsForDTP	1.3.6.1.4.1.14179.2.3.2.1.12	Unsigned32	read-write	This attribute is a bit mask specifying what to include in DCA optimization.Below is a list of parameters and their corresponding bits identifiers. options bit -------------------------------------- none 0 LOAD 1 SIGNAL STRENGTH 2 FOREIGN INTERFERENCE 4 NOISE 8 Default value is 15( all bits on).
INT bsnGlobalDot11bPowerUpdateCmdInvoke	1.3.6.1.4.1.14179.2.3.2.1.13	INTEGER	read-write	When set to activate this starts a DTP calculation regardless of the dynamic update interval. This command should be invoke on Group Leader Airespace Switch.Invoking on a Airespace Switch which is not a Group leader has no effect.
I32 bsnGlobalDot11bPowerUpdateCmdStatus	1.3.6.1.4.1.14179.2.3.2.1.14	Integer32	read-only	After setting bsnGlobalDot11aChannelUpdateCmdInvoke to activate, the result of action can be monitored from here. It takes 5 minutes for the command to complete.
INT bsnGlobalDot11bDataRate1Mhz	1.3.6.1.4.1.14179.2.3.2.1.15	INTEGER	read-write	Specify if this rate is supported or mandatory or disabled
INT bsnGlobalDot11bDataRate2Mhz	1.3.6.1.4.1.14179.2.3.2.1.16	INTEGER	read-write	Specify if this rate is supported or mandatory or disabled
INT bsnGlobalDot11bDataRate5AndHalfMhz	1.3.6.1.4.1.14179.2.3.2.1.17	INTEGER	read-write	Specify if this rate is supported or mandatory or disabled
INT bsnGlobalDot11bDataRate11Mhz	1.3.6.1.4.1.14179.2.3.2.1.18	INTEGER	read-write	Specify if this rate is supported or mandatory or disabled
INT bsnGlobalDot11bShortPreamble	1.3.6.1.4.1.14179.2.3.2.1.19	INTEGER	read-write	802.11b Short Preamble.
INT bsnGlobalDot11bDot11gSupport	1.3.6.1.4.1.14179.2.3.2.1.20	INTEGER	read-write	This attribute is enabled to also support 802.11g protocol on the 802.11b network. Enabling 802.11g allows additional data rates: 6, 9, 12, 18, 24, 36, 48, 54 Mbps.
INT bsnGlobalDot11bDataRate6Mhz	1.3.6.1.4.1.14179.2.3.2.1.21	INTEGER	read-write	Specify if this rate is supported or mandatory or disabled. This is configurable only if 802.11g support is enabled.
INT bsnGlobalDot11bDataRate9Mhz	1.3.6.1.4.1.14179.2.3.2.1.22	INTEGER	read-write	Specify if this rate is supported or mandatory or disabled. This is configurable only if 802.11g support is enabled.
INT bsnGlobalDot11bDataRate12Mhz	1.3.6.1.4.1.14179.2.3.2.1.23	INTEGER	read-write	Specify if this rate is supported or mandatory or disabled. This is configurable only if 802.11g support is enabled.
INT bsnGlobalDot11bDataRate18Mhz	1.3.6.1.4.1.14179.2.3.2.1.24	INTEGER	read-write	Specify if this rate is supported or mandatory or disabled. This is configurable only if 802.11g support is enabled.
INT bsnGlobalDot11bDataRate24Mhz	1.3.6.1.4.1.14179.2.3.2.1.25	INTEGER	read-write	Specify if this rate is supported or mandatory or disabled. This is configurable only if 802.11g support is enabled.
INT bsnGlobalDot11bDataRate36Mhz	1.3.6.1.4.1.14179.2.3.2.1.26	INTEGER	read-write	Specify if this rate is supported or mandatory or disabled. This is configurable only if 802.11g support is enabled.
INT bsnGlobalDot11bDataRate48Mhz	1.3.6.1.4.1.14179.2.3.2.1.27	INTEGER	read-write	Specify if this rate is supported or mandatory or disabled. This is configurable only if 802.11g support is enabled.
INT bsnGlobalDot11bDataRate54Mhz	1.3.6.1.4.1.14179.2.3.2.1.28	INTEGER	read-write	Specify if this rate is supported or mandatory or disabled. This is configurable only if 802.11g support is enabled.
INT bsnGlobalDot11bPicoCellMode	1.3.6.1.4.1.14179.2.3.2.1.29	INTEGER	read-write	Configures the 802.11b pico-cell mode. This cannot be enabled when the Fast Roaming Mode is enabled.
INT bsnGlobalDot11bFastRoamingMode	1.3.6.1.4.1.14179.2.3.2.1.30	INTEGER	read-write	Configures the 802.11b fast-roaming mode. This cannot be enabled when the Pico Cell Mode is enabled.
INT bsnGlobalDot11bFastRoamingVoipMinRate	1.3.6.1.4.1.14179.2.3.2.1.31	INTEGER	read-write	Configures the minimum transmission rate allowed for VoIP on any 802.11b radio.
INT bsnGlobalDot11bFastRoamingVoipPercentage	1.3.6.1.4.1.14179.2.3.2.1.32	INTEGER	read-write	Configures the percentage of effective bandwidth for the minimum rate reserved for VoIP.
INT bsnGlobalDot11b80211eMaxBandwidth	1.3.6.1.4.1.14179.2.3.2.1.33	INTEGER	read-write	This represents the maximum bandwidth allocated to 802.11e clients. It is expressed as percentage of the total bandwidth of 802.11b network. The value of this attribute can vary from 0 to 100.
INT bsnGlobalDot11bDTPCSupport	1.3.6.1.4.1.14179.2.3.2.1.34	INTEGER	read-write	This attribute may be used to enable the DTPC support on all 802.11b/g radios. DTPC or Dynamic Transmit Power Control support means that the radio's transmit power will be advertised in the beacons and probe responses.
INT bsnGlobalDot11bRxSopThreshold	1.3.6.1.4.1.14179.2.3.2.1.35	INTEGER	read-write	Configures the global 802.11b receiver start of packet threshold.
bsnGlobalDot11bPhy	1.3.6.1.4.1.14179.2.3.2.2
INT bsnGlobalDot11bMediumOccupancyLimit	1.3.6.1.4.1.14179.2.3.2.2.1	INTEGER	read-only	This attribute shall indicate the maximum amount of time, in TU, that a point coordinator may control the usage of the wireless medium without relinquishing control for long enough to allow at least one instance of DCF access to the medium. The default value of this attribute shall be 100, and the maximum value shall be 1000.
INT bsnGlobalDot11bCFPPeriod	1.3.6.1.4.1.14179.2.3.2.2.2	INTEGER	read-only	The attribute shall describe the number of DTIM intervals between the start of CFPs. It is modified by MLME-START.request primitive.
INT bsnGlobalDot11bCFPMaxDuration	1.3.6.1.4.1.14179.2.3.2.2.3	INTEGER	read-only	The attribute shall describe the maximum duration of the CFP in TU that may be generated by the PCF. It is modified by MLME-START.request primitive.
INT bsnGlobalDot11bCFPollable	1.3.6.1.4.1.14179.2.3.2.2.5	INTEGER	read-only	When this attribute is true, it shall indicate that the STA is able to respond to a CF-Poll with a data frame within a SIFS time. This attribute shall be false if the STA is not able to respond to a CF-Poll with a data frame within a SIFS time.
INT bsnGlobalDot11bCFPollRequest	1.3.6.1.4.1.14179.2.3.2.2.6	INTEGER	read-only	Specifies wheather CFP
INT bsnGlobalDot11bDTIMPeriod	1.3.6.1.4.1.14179.2.3.2.2.7	INTEGER	read-write	This attribute shall specify the number of beacon intervals that shall elapse between transmission of Beacons frames containing a TIM element whose DTIM Count field is 0. This value is transmitted in the DTIM Period field of Beacon frames.
I32 bsnGlobalDot11bMaximumTransmitPowerLevel	1.3.6.1.4.1.14179.2.3.2.2.8	Integer32	read-only	This attribute shall indicate the maximum transmit power, in dBm, allowed in the subband for the associated domain country string. The default value of this attribute shall be zero.
I32 bsnGlobalDot11bFirstChannelNumber	1.3.6.1.4.1.14179.2.3.2.2.9	Integer32	read-only	This attribute shall indicate the value of the lowest channel number in the subband for the associated domain country string. The default value of this attribute shall be zero.
I32 bsnGlobalDot11bNumberofChannels	1.3.6.1.4.1.14179.2.3.2.2.10	Integer32	read-only	This attribute shall indicate the value of the total number of channels allowed in the subband for the associated domain country string. The default value of this attribute shall be zero.
INT bsnGlobalDot11bRTSThreshold	1.3.6.1.4.1.14179.2.3.2.2.11	INTEGER	read-only	This attribute shall indicate the number of octets in an MPDU, below which an RTS/CTS handshake shall not be performed. An RTS/CTS handshake shall be performed at the beginning of any frame exchange sequence where the MPDU is of type Data or Management, the MPDU has an individual address in the Address1 field, and the length of the MPDU is greater than this threshold. (For additional details, refer to Table 21 in 9.7.) Setting this attribute to be larger than the maximum MSDU size shall have the effect of turning off the RTS/CTS handshake for frames of Data or Management type transmitted by this STA. Setting this attribute to zero shall have the effect of turning on the RTS/CTS handshake for all frames of Data or Management type transmitted by this STA. The default value of this attribute shall be 2347.
INT bsnGlobalDot11bShortRetryLimit	1.3.6.1.4.1.14179.2.3.2.2.12	INTEGER	read-only	This attribute shall indicate the maximum number of transmission attempts of a frame, the length of which is less than or equal to bsnGlobalDot11RTSThreshold, that shall be made before a failure condition is indicated. The default value of this attribute shall be 7.
INT bsnGlobalDot11bLongRetryLimit	1.3.6.1.4.1.14179.2.3.2.2.13	INTEGER	read-only	This attribute shall indicate the maximum number of transmission attempts of a frame, the length of which is greater than bsnGlobalDot11RTSThreshold, that shall be made before a failure condition is indicated. The default value of this attribute shall be 4.
INT bsnGlobalDot11bFragmentationThreshold	1.3.6.1.4.1.14179.2.3.2.2.14	INTEGER	read-write	This attribute shall specify the current maximum size, in octets, of the MPDU that may be delivered to the PHY. An MSDU shall be broken into fragments if its size exceeds the value of this attribute after adding MAC headers and trailers. An MSDU or MMPDU shall be fragmented when the resulting frame has individual address in the Address1 field, and the length of the frame is larger than this threshold. The default value for this attribute shall be the lesser of 2346 or the aMPDUMaxLength of the attached PHY and shall never exceed the lesser of 2346 or the aMPDUMaxLength of the attached PHY. The value of this attribute shall never be less than 256.
U32 bsnGlobalDot11bMaxTransmitMSDULifetime	1.3.6.1.4.1.14179.2.3.2.2.15	Unsigned32	read-only	The MaxTransmitMSDULifetime shall be the elapsed time in TU, after the initial transmission of an MSDU, after which further attempts to transmit the MSDU shall be terminated. The default value of this attribute shall be 512.
U32 bsnGlobalDot11bMaxReceiveLifetime	1.3.6.1.4.1.14179.2.3.2.2.16	Unsigned32	read-only	The MaxReceiveLifetime shall be the elapsed time in TU, after the initial reception of a fragmented MMPDU or MSDU, after which further attempts to reassemble the MMPDU or MSDU shall be terminated. The default value shall be 512.
I32 bsnGlobalDot11bEDThreshold	1.3.6.1.4.1.14179.2.3.2.2.17	Integer32	read-only	The current Energy Detect Threshold being used by the DSSS PHY.
INT bsnGlobalDot11bChannelAgilityEnabled	1.3.6.1.4.1.14179.2.3.2.2.18	INTEGER	read-only	This attribute indicates that the PHY channel agility functionality is enabled.
INT bsnGlobalDot11bPBCCOptionImplemented	1.3.6.1.4.1.14179.2.3.2.2.19	INTEGER	read-only	This attribute, when true, shall indicate that the PBCC modulation option as defined in subclause 18.4.6.6 is implemented. The default value of this attribute shall be false.
INT bsnGlobalDot11bShortPreambleOptionImplemented	1.3.6.1.4.1.14179.2.3.2.2.20	INTEGER	read-only	This attribute, when true, shall indicate that the short preamble option as defined in subclause 18.2.2.2 is implemented. The default value of this attribute shall be false.
bsnGlobalDot11a	1.3.6.1.4.1.14179.2.3.3
bsnGlobalDot11aConfig	1.3.6.1.4.1.14179.2.3.3.1
INT bsnGlobalDot11aNetworkStatus	1.3.6.1.4.1.14179.2.3.3.1.1	INTEGER	read-write	Dot11a Network Status
INT bsnGlobalDot11aLowBandNetwork	1.3.6.1.4.1.14179.2.3.3.1.2	INTEGER	read-only	Dot11a Low Band Network Status
INT bsnGlobalDot11aMediumBandNetwork	1.3.6.1.4.1.14179.2.3.3.1.3	INTEGER	read-only	Dot11a Mid Band Network Status
INT bsnGlobalDot11aHighBandNetwork	1.3.6.1.4.1.14179.2.3.3.1.4	INTEGER	read-only	Dot11a High Band Network Status
INT bsnGlobalDot11aBeaconPeriod	1.3.6.1.4.1.14179.2.3.3.1.5	INTEGER	read-write	This attribute shall specify the number of TU that a AP Radio shall use for scheduling Beacon tranmissions. This value is transmitted in Beacon and Probe Response frames.
INT bsnGlobalDot11aDynamicChannelAssignment	1.3.6.1.4.1.14179.2.3.3.1.6	INTEGER	read-write	Dynamic channel assignment(DCA) has three modes. When the mode is auto, the channel assignment will be periodically updated for all Airespace APs that permit this operation. When the DCA is runOnce, channel assignments are updated based on the UPDATE_CMD received from the management. When the DCA is static, no dynamic channel assignments occurs and value are set to their global default. Default is auto.
INT bsnGlobalDot11aCurrentChannel	1.3.6.1.4.1.14179.2.3.3.1.7	INTEGER	read-write	The number of the current operating frequency channel of the OFDM PHY.
U32 bsnGlobalDot11aDynamicChannelUpdateInterval	1.3.6.1.4.1.14179.2.3.3.1.8	Unsigned32	read-only	When Channel dynamic alogirthm is running, this interval(in secs) specifies how often Channel assignement updates are attempted on an Airespace AP. NOTE: hysteresis is build into the algorithms so we will not have uproductive changes occuring. Default value is 600 secs
U32 bsnGlobalDot11aInputsForDCA	1.3.6.1.4.1.14179.2.3.3.1.9	Unsigned32	read-write	This attribute is a bit mask specifying what to include in DCA optimization.Below is a list of parameters and their corresponding bits identifiers. options bit -------------------------------------- none 0 SIGNAL STRENGTH 1 NOISE 2 FOREIGN INTERFERENCE 4 LOAD 8 DEVICE INTERFERENCE 32 Default value is 63( all bits on).
INT bsnGlobalDot11aChannelUpdateCmdInvoke	1.3.6.1.4.1.14179.2.3.3.1.10	INTEGER	read-write	When set to activate this starts a DCA calculation regardless of the dynamic update interval. This command should be invoke on Group Leader Airespace Switch.Invoking on a Airespace Switch which is not a Group leader has no effect.
I32 bsnGlobalDot11aChannelUpdateCmdStatus	1.3.6.1.4.1.14179.2.3.3.1.11	Integer32	read-only	After setting bsnGlobalDot11aChannelUpdateCmdInvoke to activate, the result of action can be monitored from here. It takes 5 minutes for the command to complete.
INT bsnGlobalDot11aDynamicTransmitPowerControl	1.3.6.1.4.1.14179.2.3.3.1.12	INTEGER	read-write	Dynamic transmit power (DTP) has three modes. When the mode is auto, the transmit power of each Airespace AP will be periodically updated for all Airespace APs that permit this operation. When the DTP is runOnce,transmit power update will occur based on the UPDATE_CMD received from the management. When the DTP is static, no dynamic transmit power updates occur and their global defaults are used. Default is auto.
INT bsnGlobalDot11aCurrentTxPowerLevel	1.3.6.1.4.1.14179.2.3.3.1.13	INTEGER	read-write	The TxPowerLevel N currently being used to transmit data. Some PHYs also use this value to determine the receiver sensitivity requirements for CCA.
U32 bsnGlobalDot11aDynamicTxPowerControlInterval	1.3.6.1.4.1.14179.2.3.3.1.14	Unsigned32	read-only	When Tx PowerControl dynamic alogirthm is running, this interval(in secs) specifies how often TxPower control updates are attempted on an Airespace AP. NOTE: hysteresis is build into the algorithms so we will not have uproductive changes occuring. Default value is 600 secs
U32 bsnGlobalDot11aInputsForDTP	1.3.6.1.4.1.14179.2.3.3.1.15	Unsigned32	read-write	This attribute is a bit mask specifying what to include in DCA optimization.Below is a list of parameters and their corresponding bits identifiers. options bit -------------------------------------- none 0 LOAD 1 SIGNAL STRENGTH 2 FOREIGN INTERFERENCE 4 NOISE 8 Default value is 15( all bits on).
INT bsnGlobalDot11aPowerUpdateCmdInvoke	1.3.6.1.4.1.14179.2.3.3.1.16	INTEGER	read-write	When set to activate this starts a DTP calculation regardless of the dynamic update interval. This command should be invoke on Group Leader Airespace Switch.Invoking on a Airespace Switch which is not a Group leader has no effect.
I32 bsnGlobalDot11aPowerUpdateCmdStatus	1.3.6.1.4.1.14179.2.3.3.1.17	Integer32	read-only	After setting bsnGlobalDot11aChannelUpdateCmdInvoke to activate, the result of action can be monitored from here. It takes 5 minutes for the command to complete.
INT bsnGlobalDot11aDataRate6Mhz	1.3.6.1.4.1.14179.2.3.3.1.19	INTEGER	read-write	Specify if this rate is supported or mandatory or disabled
INT bsnGlobalDot11aDataRate9Mhz	1.3.6.1.4.1.14179.2.3.3.1.20	INTEGER	read-write	Specify if this rate is supported or mandatory or disabled
INT bsnGlobalDot11aDataRate12Mhz	1.3.6.1.4.1.14179.2.3.3.1.21	INTEGER	read-write	Specify if this rate is supported or mandatory or disabled
INT bsnGlobalDot11aDataRate18Mhz	1.3.6.1.4.1.14179.2.3.3.1.22	INTEGER	read-write	Specify if this rate is supported or mandatory or disabled
INT bsnGlobalDot11aDataRate24Mhz	1.3.6.1.4.1.14179.2.3.3.1.23	INTEGER	read-write	Specify if this rate is supported or mandatory or disabled
INT bsnGlobalDot11aDataRate36Mhz	1.3.6.1.4.1.14179.2.3.3.1.24	INTEGER	read-write	Specify if this rate is supported or mandatory or disabled
INT bsnGlobalDot11aDataRate48Mhz	1.3.6.1.4.1.14179.2.3.3.1.25	INTEGER	read-write	Specify if this rate is supported or mandatory or disabled
INT bsnGlobalDot11aDataRate54Mhz	1.3.6.1.4.1.14179.2.3.3.1.26	INTEGER	read-write	Specify if this rate is supported or mandatory or disabled
INT bsnGlobalDot11aPicoCellMode	1.3.6.1.4.1.14179.2.3.3.1.27	INTEGER	read-write	Configures the 802.11a pico-cell mode. This cannot be enabled when the Fast Roaming Mode is enabled.
INT bsnGlobalDot11aFastRoamingMode	1.3.6.1.4.1.14179.2.3.3.1.28	INTEGER	read-write	Configures the 802.11a fast-roaming mode. This cannot be enabled when the Pico Cell Mode is enabled.
INT bsnGlobalDot11aFastRoamingVoipMinRate	1.3.6.1.4.1.14179.2.3.3.1.29	INTEGER	read-write	Configures the minimum transmission rate allowed for VoIP on any 802.11a radio.
INT bsnGlobalDot11aFastRoamingVoipPercentage	1.3.6.1.4.1.14179.2.3.3.1.30	INTEGER	read-write	Configures the percentage of effective bandwidth for the minimum rate reserved for VoIP.
INT bsnGlobalDot11a80211eMaxBandwidth	1.3.6.1.4.1.14179.2.3.3.1.31	INTEGER	read-write	This represents the maximum bandwidth allocated to 802.11e clients. It is expressed as percentage of the total bandwidth of 802.11a network. The value of this attribute can vary from 0 to 100.
INT bsnGlobalDot11aDTPCSupport	1.3.6.1.4.1.14179.2.3.3.1.32	INTEGER	read-write	This attribute may be used to enable the DTPC support on all 802.11a radios. DTPC or Dynamic Transmit Power Control support means that the radio's transmit power will be advertised in the beacons and probe responses.
INT bsnGlobalDot11aRxSopThreshold	1.3.6.1.4.1.14179.2.3.3.1.33	INTEGER	read-write	Configures the global 802.11a receiver start of packet threshold.
bsnGlobalDot11aPhy	1.3.6.1.4.1.14179.2.3.3.2
INT bsnGlobalDot11aMediumOccupancyLimit	1.3.6.1.4.1.14179.2.3.3.2.1	INTEGER	read-only	This attribute shall indicate the maximum amount of time, in TU, that a point coordinator may control the usage of the wireless medium without relinquishing control for long enough to allow at least one instance of DCF access to the medium. The default value of this attribute shall be 100, and the maximum value shall be 1000.
INT bsnGlobalDot11aCFPPeriod	1.3.6.1.4.1.14179.2.3.3.2.2	INTEGER	read-only	The attribute shall describe the number of DTIM intervals between the start of CFPs. It is modified by MLME-START.request primitive.
INT bsnGlobalDot11aCFPMaxDuration	1.3.6.1.4.1.14179.2.3.3.2.3	INTEGER	read-only	The attribute shall describe the maximum duration of the CFP in TU that may be generated by the PCF. It is modified by MLME-START.request primitive.
INT bsnGlobalDot11aCFPollable	1.3.6.1.4.1.14179.2.3.3.2.5	INTEGER	read-only	When this attribute is true, it shall indicate that the STA is able to respond to a CF-Poll with a data frame within a SIFS time. This attribute shall be false if the STA is not able to respond to a CF-Poll with a data frame within a SIFS time.
INT bsnGlobalDot11aCFPollRequest	1.3.6.1.4.1.14179.2.3.3.2.6	INTEGER	read-only	Specifies whether CFP
INT bsnGlobalDot11aDTIMPeriod	1.3.6.1.4.1.14179.2.3.3.2.7	INTEGER	read-write	This attribute shall specify the number of beacon intervals that shall elapse between transmission of Beacons frames containing a TIM element whose DTIM Count field is 0. This value is transmitted in the DTIM Period field of Beacon frames.
I32 bsnGlobalDot11aMaximumTransmitPowerLevel	1.3.6.1.4.1.14179.2.3.3.2.8	Integer32	read-only	This attribute shall indicate the maximum transmit power, in dBm, allowed in the subband for the associated domain country string. The default value of this attribute shall be zero.
I32 bsnGlobalDot11aFirstChannelNumber	1.3.6.1.4.1.14179.2.3.3.2.9	Integer32	read-only	This attribute shall indicate the value of the lowest channel number in the subband for the associated domain country string. The default value of this attribute shall be zero.
I32 bsnGlobalDot11aNumberofChannels	1.3.6.1.4.1.14179.2.3.3.2.10	Integer32	read-only	This attribute shall indicate the value of the total number of channels allowed in the subband for the associated domain country string. The default value of this attribute shall be zero.
INT bsnGlobalDot11aRTSThreshold	1.3.6.1.4.1.14179.2.3.3.2.11	INTEGER	read-only	This attribute shall indicate the number of octets in an MPDU, below which an RTS/CTS handshake shall not be performed. An RTS/CTS handshake shall be performed at the beginning of any frame exchange sequence where the MPDU is of type Data or Management, the MPDU has an individual address in the Address1 field, and the length of the MPDU is greater than this threshold. (For additional details, refer to Table 21 in 9.7.) Setting this attribute to be larger than the maximum MSDU size shall have the effect of turning off the RTS/CTS handshake for frames of Data or Management type transmitted by this STA. Setting this attribute to zero shall have the effect of turning on the RTS/CTS handshake for all frames of Data or Management type transmitted by this STA. The default value of this attribute shall be 2347.
INT bsnGlobalDot11aShortRetryLimit	1.3.6.1.4.1.14179.2.3.3.2.12	INTEGER	read-only	This attribute shall indicate the maximum number of transmission attempts of a frame, the length of which is less than or equal to bsnGlobalDot11RTSThreshold, that shall be made before a failure condition is indicated. The default value of this attribute shall be 7.
INT bsnGlobalDot11aLongRetryLimit	1.3.6.1.4.1.14179.2.3.3.2.13	INTEGER	read-only	This attribute shall indicate the maximum number of transmission attempts of a frame, the length of which is greater than bsnGlobalDot11RTSThreshold, that shall be made before a failure condition is indicated. The default value of this attribute shall be 4.
INT bsnGlobalDot11aFragmentationThreshold	1.3.6.1.4.1.14179.2.3.3.2.14	INTEGER	read-write	This attribute shall specify the current maximum size, in octets, of the MPDU that may be delivered to the PHY. An MSDU shall be broken into fragments if its size exceeds the value of this attribute after adding MAC headers and trailers. MSDU or MMPDU shall be fragmented when the resulting frame has an individual address in the Address1 field, and the length of the frame is larger than this threshold. The default value for this attribute shall be the lesser of 2346 or the aMPDUMaxLength of the attached PHY and shall never exceed the lesser of 2346 or the aMPDUMaxLength of the attached PHY. The value of this attribute shall never be less than 256.
U32 bsnGlobalDot11aMaxTransmitMSDULifetime	1.3.6.1.4.1.14179.2.3.3.2.15	Unsigned32	read-only	The MaxTransmitMSDULifetime shall be the elapsed time in TU, after the initial transmission of an MSDU, after which further attempts to transmit the MSDU shall be terminated. The default value of this attribute shall be 512.
U32 bsnGlobalDot11aMaxReceiveLifetime	1.3.6.1.4.1.14179.2.3.3.2.16	Unsigned32	read-only	The MaxReceiveLifetime shall be the elapsed time in TU, after the initial reception of a fragmented MMPDU or MSDU, after which further attempts to reassemble the MMPDU or MSDU shall be terminated. The default value shall be 512.
I32 bsnGlobalDot11aTIThreshold	1.3.6.1.4.1.14179.2.3.3.2.17	Integer32	read-only	The Threshold being used to detect a busy medium (frequency). CCA shall report a busy medium upon detecting the RSSI above this threshold.
INT bsnGlobalDot11aChannelAgilityEnabled	1.3.6.1.4.1.14179.2.3.3.2.18	INTEGER	read-only	This attribute indicates that the PHY channel agility functionality is enabled.
bsnGlobalDot11h	1.3.6.1.4.1.14179.2.3.4
bsnGlobalDot11hConfig	1.3.6.1.4.1.14179.2.3.4.1
INT bsnGlobalDot11hPowerConstraint	1.3.6.1.4.1.14179.2.3.4.1.1	INTEGER	read-write	Local maximum transmit power for a channel is defined as maximum transmit power level specified for the channel in the Country element minus the local power constraint specified for the channel in the Power Constraint element.The power constraint is coded as an unsigned integer in units of decibels. To disable power constraint set Power Constraint to 0.
INT bsnGlobalDot11hChannelSwitchEnable	1.3.6.1.4.1.14179.2.3.4.1.2	INTEGER	read-write	To enable or disable channel switch. When disabling Channel Switch no need to pass mode and count
INT bsnGlobalDot11hChannelSwitchMode	1.3.6.1.4.1.14179.2.3.4.1.3	INTEGER	read-write	The Channel Switch Mode indicates any restriction on transmission until a channel switch. An Channel mode set to 1 means that the STA in a BSS to which the frame containing the element is addressed shall tranmit no further frames with in the BSS until the scheduled channel switch. A Channel switch mode set to 0 does not impose any requirement on the receiving STA.
bsnRrm	1.3.6.1.4.1.14179.2.4
bsnRrmDot11a	1.3.6.1.4.1.14179.2.4.1
bsnRrmDot11aGroup	1.3.6.1.4.1.14179.2.4.1.1
INT bsnRrmDot11aGlobalAutomaticGrouping	1.3.6.1.4.1.14179.2.4.1.1.1	INTEGER	read-write	Dynamic grouping has two modes: on and off. When the grouping is off, no dynamic grouping occurs. Each Airespace Switch optimizes only its own Airespace APs' parameters. When grouping is on, the Airespace Switches form groups and elect leaders to perform better dynamic parameter optimization.
MAC bsnRrmDot11aGroupLeaderMacAddr	1.3.6.1.4.1.14179.2.4.1.1.2	MacAddress	read-only	This is the MAC address of the group leader for the dot11a group containing this Airespace Switch.
INT bsnRrmIsDot11aGroupLeader	1.3.6.1.4.1.14179.2.4.1.1.3	INTEGER	read-only	If this Airespace Switch is a Dot11a Group Leader then this attribute will be true else it will be false.
U32 bsnRrmDot11aGroupLastUpdateTime	1.3.6.1.4.1.14179.2.4.1.1.4	Unsigned32	read-only	Last time the dot11a grouping was updated on this Airespace Switch. This is valid only if the Airespace Switch is a group leader.
U32 bsnRrmDot11aGlobalGroupInterval	1.3.6.1.4.1.14179.2.4.1.1.5	Unsigned32	read-only	When grouping is on, this interval(in secs) represents the period with which the grouping algorithm is run. Grouping algorithm will also run when the group contents changes and the automatic grouping is enabled. A dynamic grouping can be started upon request from the system administrator. Default value is 3600 secs.
bsnWrasDot11aGroupTable	1.3.6.1.4.1.14179.2.4.1.1.9		not-accessible	This is a table of Airespace Switch addresses that identifies the members of the Dot11a RF group containing this Airespace Switch. Max size is 20 entries.This has been deprecated for clrRrmDot11BandGrpMemberTable.
bsnWrasDot11aGroupEntry	1.3.6.1.4.1.14179.2.4.1.1.9.1		not-accessible	...
MAC bsnWrasDot11aPeerMacAddress	1.3.6.1.4.1.14179.2.4.1.1.9.1.1	MacAddress	read-only	The MAC address of the member Switch.
IP bsnWrasDot11aPeerIpAddress	1.3.6.1.4.1.14179.2.4.1.1.9.1.21	IpAddress	read-only	The IP address of the Airespace Switch.
bsnRrmDot11aAPDefault	1.3.6.1.4.1.14179.2.4.1.6
INT bsnRrmDot11aForeignInterferenceThreshold	1.3.6.1.4.1.14179.2.4.1.6.1	INTEGER	read-write	foreign 802.11A interference threshold between 0 and 100 percent.
INT bsnRrmDot11aForeignNoiseThreshold	1.3.6.1.4.1.14179.2.4.1.6.2	INTEGER	read-write	802.11A foreign noise threshold between -127 and 0 dBm.
INT bsnRrmDot11aRFUtilizationThreshold	1.3.6.1.4.1.14179.2.4.1.6.3	INTEGER	read-write	802.11A RF utlization threshold between 0 and 100 percent.
U32 bsnRrmDot11aThroughputThreshold	1.3.6.1.4.1.14179.2.4.1.6.4	Unsigned32	read-write	802.11A throughput threshold between 1000 and 100000
INT bsnRrmDot11aMobilesThreshold	1.3.6.1.4.1.14179.2.4.1.6.5	INTEGER	read-write	802.11A mobiles threshold between 1 and 75
INT bsnRrmDot11aCoverageThreshold	1.3.6.1.4.1.14179.2.4.1.6.6	INTEGER	read-write	802.11A coverage threshold between 3 and 50.
INT bsnRrmDot11aMobileMinExceptionLevel	1.3.6.1.4.1.14179.2.4.1.6.7	INTEGER	read-write	802.11A mobile minimum exception level between 1 and 75
INT bsnRrmDot11aCoverageExceptionLevel	1.3.6.1.4.1.14179.2.4.1.6.8	INTEGER	read-write	802.11A coverage exception level between 0 and 100 percent.
U32 bsnRrmDot11aSignalMeasurementInterval	1.3.6.1.4.1.14179.2.4.1.6.9	Unsigned32	read-write	This interval (in secs) specifies how often do we get new signal strength measurements at each Airespace AP. Default is 300 secs
U32 bsnRrmDot11aNoiseMeasurementInterval	1.3.6.1.4.1.14179.2.4.1.6.10	Unsigned32	read-write	This interval( in secs) specifies how often do we get new noise and interference measurements at each Airespace AP. Default is 300 secs
U32 bsnRrmDot11aLoadMeasurementInterval	1.3.6.1.4.1.14179.2.4.1.6.11	Unsigned32	read-write	This interval( in secs) specifies how often do we get new load measurements at each Airespace AP. Default is 300 secs
U32 bsnRrmDot11aCoverageMeasurementInterval	1.3.6.1.4.1.14179.2.4.1.6.12	Unsigned32	read-write	This interval( in secs) specifies how often do we get new coverage measurements at each Airespace AP. Default is 300 secs
INT bsnRrmDot11aChannelMonitorList	1.3.6.1.4.1.14179.2.4.1.6.13	INTEGER	read-write	This attribute specifies the channels on which the switch monitors noise, interference and rogues. The first option allows monitoring on all channels while the second one on only those that are supported by the country of operation. the option dca implies that the monitor channel list will include those channels that are used by automatic channel assignment.
INT bsnRrmDot11aSetFactoryDefault	1.3.6.1.4.1.14179.2.4.1.7	INTEGER	read-write	When set to activate all rrm parameters are reset to factory defaults
bsnRrmDot11b	1.3.6.1.4.1.14179.2.4.2
bsnRrmDot11bGroup	1.3.6.1.4.1.14179.2.4.2.1
INT bsnRrmDot11bGlobalAutomaticGrouping	1.3.6.1.4.1.14179.2.4.2.1.1	INTEGER	read-write	Dynamic grouping has two modes: on and off. When the grouping is off, no dynamic grouping occurs. Each Airespace Switch optimizes only its own Airespace APs' parameters. When grouping is on, the Airespace Switchs form groups and elect leaders to perform better dynamic parameter optimization.This has been deprecated for clrRrmDot11BandGrpTable.
MAC bsnRrmDot11bGroupLeaderMacAddr	1.3.6.1.4.1.14179.2.4.2.1.2	MacAddress	read-only	This is the MAC address of the group leader for the dot11b group containing this Airespace Switch.This has been deprecated for clrRrmDot11BandGrpTable.
INT bsnRrmIsDot11bGroupLeader	1.3.6.1.4.1.14179.2.4.2.1.3	INTEGER	read-only	If this Airespace Switch is a Dot11b Group Leader then this attribute will be true else it will be false.This has been deprecated for clrRrmDot11BandGrpTable.
U32 bsnRrmDot11bGroupLastUpdateTime	1.3.6.1.4.1.14179.2.4.2.1.4	Unsigned32	read-only	Last time the dot11b grouping was updated on this Airespace Switch. This is valid only if the Airespace Switch is a group leader.This has been deprecated for clrRrmDot11BandGrpTable.
U32 bsnRrmDot11bGlobalGroupInterval	1.3.6.1.4.1.14179.2.4.2.1.5	Unsigned32	read-only	When grouping is on, this interval(in secs) represents the period with which the grouping algorithm is run. Grouping algorithm will also run when the group contents changes and the automatic grouping is enabled. A dynamic grouping can be started upon request from the system administrator. Default value is 3600 secs.This has been deprecated for clrRrmDot11BandGrpTable.
bsnWrasDot11bGroupTable	1.3.6.1.4.1.14179.2.4.2.1.9		not-accessible	This is a table of Airespace Switch addresses that identifies the members of the Dot11b RF group containing this Airespace Switch. Max size is 20 entries.This has been deprecated for clrRrmDot11BandGrpMemberTable.
bsnWrasDot11bGroupEntry	1.3.6.1.4.1.14179.2.4.2.1.9.1		not-accessible	...
MAC bsnWrasDot11bPeerMacAddress	1.3.6.1.4.1.14179.2.4.2.1.9.1.1	MacAddress	read-only	The MAC address of the GIGE interface.
IP bsnWrasDot11bPeerIpAddress	1.3.6.1.4.1.14179.2.4.2.1.9.1.21	IpAddress	read-only	The IP address of the Airespace Switch.
bsnRrmDot11bAPDefault	1.3.6.1.4.1.14179.2.4.2.6
INT bsnRrmDot11bForeignInterferenceThreshold	1.3.6.1.4.1.14179.2.4.2.6.1	INTEGER	read-write	Foreign 802.11A interference threshold between 0 and 100 percent.
INT bsnRrmDot11bForeignNoiseThreshold	1.3.6.1.4.1.14179.2.4.2.6.2	INTEGER	read-write	802.11A foreign noise threshold between -127 and 0 dBm.
INT bsnRrmDot11bRFUtilizationThreshold	1.3.6.1.4.1.14179.2.4.2.6.3	INTEGER	read-write	802.11A RF utlization threshold between 0 and 100 percent.
U32 bsnRrmDot11bThroughputThreshold	1.3.6.1.4.1.14179.2.4.2.6.4	Unsigned32	read-write	802.11A Airespace AP data-rate threshold between 1000 and 100000
INT bsnRrmDot11bMobilesThreshold	1.3.6.1.4.1.14179.2.4.2.6.5	INTEGER	read-write	802.11A Airespace AP mobiles threshold between 1 and 75
INT bsnRrmDot11bCoverageThreshold	1.3.6.1.4.1.14179.2.4.2.6.6	INTEGER	read-write	802.11A Airespace AP coverage threshold between 3 and 50.
INT bsnRrmDot11bMobileMinExceptionLevel	1.3.6.1.4.1.14179.2.4.2.6.7	INTEGER	read-write	802.11A Airespace AP mobile minimum exception level between 1 and 75
INT bsnRrmDot11bCoverageExceptionLevel	1.3.6.1.4.1.14179.2.4.2.6.8	INTEGER	read-write	802.11A Airespace AP coverage exception level between 0 and 100 percent.
U32 bsnRrmDot11bSignalMeasurementInterval	1.3.6.1.4.1.14179.2.4.2.6.9	Unsigned32	read-write	This interval( in secs) specifies how often do we get new signal strength measurements at each Airespace AP. Default is 300 secs
U32 bsnRrmDot11bNoiseMeasurementInterval	1.3.6.1.4.1.14179.2.4.2.6.10	Unsigned32	read-write	This interval( in secs) specifies how often do we get new noise and interference measurements at each Airespace AP. Default is 300 secs
U32 bsnRrmDot11bLoadMeasurementInterval	1.3.6.1.4.1.14179.2.4.2.6.11	Unsigned32	read-write	This interval( in secs) specifies how often do we get new load measurements at each Airespace AP. Default is 300 secs
U32 bsnRrmDot11bCoverageMeasurementInterval	1.3.6.1.4.1.14179.2.4.2.6.12	Unsigned32	read-write	This interval( in secs) specifies how often do we get new coverage measurements at each Airespace AP. Default is 300 secs
INT bsnRrmDot11bChannelMonitorList	1.3.6.1.4.1.14179.2.4.2.6.13	INTEGER	read-write	This attribute specifies the channels on which the switch monitors noise, interference and rogues. The first option allows monitoring on all channels while the second one on only those that are supported by the country of operation. the option dca implies that the monitor channel list will include those channels that are used by automatic channel assignment.
INT bsnRrmDot11bSetFactoryDefault	1.3.6.1.4.1.14179.2.4.2.7	INTEGER	read-write	When set to activate all rrm parameters are reset to factory defaults
bsnAAA	1.3.6.1.4.1.14179.2.5
bsnRadiusAuthServerTable	1.3.6.1.4.1.14179.2.5.1		not-accessible	The (conceptual) table listing the RADIUS authentication servers with which the client shares a secret.
bsnRadiusAuthServerEntry	1.3.6.1.4.1.14179.2.5.1.1		not-accessible	An entry (conceptual row) representing a RADIUS authentication server with which the client shares a secret.
I32 bsnRadiusAuthServerIndex	1.3.6.1.4.1.14179.2.5.1.1.1	Integer32	read-create	A number uniquely identifying each RADIUS Authentication server with which this client communicates.
IP bsnRadiusAuthServerAddress	1.3.6.1.4.1.14179.2.5.1.1.2	IpAddress	read-create	The IP address of the RADIUS authentication server referred to in this table entry.
I32 bsnRadiusAuthClientServerPortNumber	1.3.6.1.4.1.14179.2.5.1.1.3	Integer32	read-create	The UDP port the client is using to send requests to this server.
OCT bsnRadiusAuthServerKey	1.3.6.1.4.1.14179.2.5.1.1.4	OCTET STRING	read-create	The authentication and encryption key shared between the Radius client and this Radius Server. When the bsnRadiusAuthServerKeyFormat is hex it can have max length of 128 bytes. If the bsnRadiusAuthServerKeyFormat is Ascii it can have max length of 64 bytes.
INT bsnRadiusAuthServerStatus	1.3.6.1.4.1.14179.2.5.1.1.5	INTEGER	read-create	Server enable or disable status.
INT bsnRadiusAuthServerKeyFormat	1.3.6.1.4.1.14179.2.5.1.1.6	INTEGER	read-create	Format of the server key. When hex, the number of characters in the key should be even.
INT bsnRadiusAuthServerRFC3576	1.3.6.1.4.1.14179.2.5.1.1.7	INTEGER	read-create	Support for Dynamic Authorization Extensions to RADIUS.
INT bsnRadiusAuthServerIPSec	1.3.6.1.4.1.14179.2.5.1.1.8	INTEGER	read-create	IPSec over RADIUS
INT bsnRadiusAuthServerIPSecAuth	1.3.6.1.4.1.14179.2.5.1.1.9	INTEGER	read-create	The Hash algorithm employed by the IPSec Encrpytion. This applies only when bsnRadiusAuthServerIPSec is in enable state.
INT bsnRadiusAuthServerIPSecEncryption	1.3.6.1.4.1.14179.2.5.1.1.10	INTEGER	read-create	The Encryption algorithm employed by this IpSec Encryption. This applies only when bsnRadiusAuthServerIPSec is in enable state.
INT bsnRadiusAuthServerIPSecIKEPhase1	1.3.6.1.4.1.14179.2.5.1.1.11	INTEGER	read-create	VPN IKE Phase 1 Mode type as per the IpSec standards. This applies only when bsnRadiusAuthServerIPSec is in enable state.
I32 bsnRadiusAuthServerIPSecIKELifetime	1.3.6.1.4.1.14179.2.5.1.1.12	Integer32	read-create	IPSec IKE's Lifetime. This applies only when bsnRadiusAuthServerIPSec is in enable state.
INT bsnRadiusAuthServerIPSecDHGroup	1.3.6.1.4.1.14179.2.5.1.1.13	INTEGER	read-create	IKE's Diffie-Hellman Group. This applies only when bsnRadiusAuthServerIPSec is in enable state.
INT bsnRadiusAuthServerNetworkUserConfig	1.3.6.1.4.1.14179.2.5.1.1.14	INTEGER	read-create	When enabled, this entry is considered as network user radius authenticating server entry.
INT bsnRadiusAuthServerMgmtUserConfig	1.3.6.1.4.1.14179.2.5.1.1.15	INTEGER	read-create	When enabled, this entry is considered as management user radius authenticating server entry.
INT bsnRadiusAuthServerRetransmitTimeout	1.3.6.1.4.1.14179.2.5.1.1.17	INTEGER	read-create	Time in seconds after which a radius authentication request will timeout and a retransmission will be taken up by the switch.
OCT bsnRadiusAuthServerKeyWrapKEKkey	1.3.6.1.4.1.14179.2.5.1.1.18	OCTET STRING	read-create	Key-encryption-key (KEK) used as the key for the 128 bit AES Key Wrap algorithm to encrypt the PMK in the key attribute. If the key is present in request, it should be taken as a hint by the server that the sender prefers this method of encryption over others. To maintain security actual keys after configuration are never returned in get request. If keys are configured then '***' is returned. If keys are not configured then empty string is retunred. bsnRadiusAuthServerKeyFormat is used this key. if the format chosen is ascii then it should be 16 bytes in length. if the format chosen is hex then it should be 32 bytes in length.
OCT bsnRadiusAuthServerKeyWrapMACKkey	1.3.6.1.4.1.14179.2.5.1.1.19	OCTET STRING	read-create	Message-authenticator-code-key ( MACK) - used as the key for the HMAC-SHA-1 algorithm to sign the RADIUS message to prevent spoofing. MACK must be configured when KEK is configured. To maintain security actual keys after configuration are never returned in get request. If keys are configured then '***' is returned. If keys are not configured then empty string is returned. bsnRadiusAuthServerKeyFormat is used this key. if the format chosen is ascii then it should be 20 bytes in length. If the format chosen is hex then it should be 40 bytes in length.
INT bsnRadiusAuthServerKeyWrapFormat	1.3.6.1.4.1.14179.2.5.1.1.20	INTEGER	read-create	Format for the Key Wrap keys. This object is mandatory for manager to send if the key Wrap keys are being configured. Get on this object will always return hex(1)
ROW bsnRadiusAuthServerRowStatus	1.3.6.1.4.1.14179.2.5.1.1.26	RowStatus	read-create	Row Status for creation/deletion
IPt bsnRadiusAuthServerInetAddressType	1.3.6.1.4.1.14179.2.5.1.1.27	InetAddressType	read-create	The IP address of the RADIUS authentication server referred to in this table entry.
IP bsnRadiusAuthServerInetAddress	1.3.6.1.4.1.14179.2.5.1.1.28	InetAddress	read-create	The IP address of the RADIUS authentication server referred to in this table entry.
bsnRadiusAccServerTable	1.3.6.1.4.1.14179.2.5.2		not-accessible	The (conceptual) table listing the RADIUS accounting servers with which the client shares a secret.
bsnRadiusAccServerEntry	1.3.6.1.4.1.14179.2.5.2.1		not-accessible	An entry (conceptual row) representing a RADIUS accounting server with which the client shares a secret.
I32 bsnRadiusAccServerIndex	1.3.6.1.4.1.14179.2.5.2.1.1	Integer32	read-create	A number uniquely identifying each RADIUS Accounting server with which this client communicates.
IP bsnRadiusAccServerAddress	1.3.6.1.4.1.14179.2.5.2.1.2	IpAddress	read-create	The IP address of the RADIUS accounting server referred to in this table entry.
I32 bsnRadiusAccClientServerPortNumber	1.3.6.1.4.1.14179.2.5.2.1.3	Integer32	read-create	The UDP port the client is using to send requests to this server.
OCT bsnRadiusAccServerKey	1.3.6.1.4.1.14179.2.5.2.1.4	OCTET STRING	read-create	The authentication and encryption key shared between the Radius client and this Radius Server. When the bsnRadiusAccServerKeyFormat is hex it can have max length of 128 bytes. If the bsnRadiusAccServerKeyFormat is Ascii it can have max length of 64 bytes.
INT bsnRadiusAccServerStatus	1.3.6.1.4.1.14179.2.5.2.1.5	INTEGER	read-create	Server enable or disable status.
INT bsnRadiusAccServerKeyFormat	1.3.6.1.4.1.14179.2.5.2.1.6	INTEGER	read-create	Format of the server key. When hex, the number of characters in the key should be even.
INT bsnRadiusAccServerIPSec	1.3.6.1.4.1.14179.2.5.2.1.7	INTEGER	read-create	IPSec over RADIUS
INT bsnRadiusAccServerIPSecAuth	1.3.6.1.4.1.14179.2.5.2.1.8	INTEGER	read-create	The Hash algorithm employed by the IPSec Encrpytion. This applies only when bsnRadiusAccServerIPSec is in enable state.
INT bsnRadiusAccServerIPSecEncryption	1.3.6.1.4.1.14179.2.5.2.1.9	INTEGER	read-create	The Encryption algorithm employed by this IpSec Encryption. This applies only when bsnRadiusAccServerIPSec is in enable state.
INT bsnRadiusAccServerIPSecIKEPhase1	1.3.6.1.4.1.14179.2.5.2.1.10	INTEGER	read-create	VPN IKE Phase 1 Mode type as per the IpSec standards. This applies only when bsnRadiusAccServerIPSec is in enable state.
I32 bsnRadiusAccServerIPSecIKELifetime	1.3.6.1.4.1.14179.2.5.2.1.11	Integer32	read-create	IPSec IKE's Lifetime. This applies only when bsnRadiusAccServerIPSec is in enable state.
INT bsnRadiusAccServerIPSecDHGroup	1.3.6.1.4.1.14179.2.5.2.1.12	INTEGER	read-create	IKE's Diffie-Hellman Group. This applies only when bsnRadiusAccServerIPSec is in enable state.
INT bsnRadiusAccServerNetworkUserConfig	1.3.6.1.4.1.14179.2.5.2.1.13	INTEGER	read-create	When enabled, this entry is considered as network user radius accounting server entry.
INT bsnRadiusAccServerRetransmitTimeout	1.3.6.1.4.1.14179.2.5.2.1.14	INTEGER	read-create	Time in seconds after which a radius accounting request will timeout and a retransmission will be taken up by the switch.
ROW bsnRadiusAccServerRowStatus	1.3.6.1.4.1.14179.2.5.2.1.26	RowStatus	read-create	Row Status for creation/deletion
IPt bsnRadiusAccServerInetAddressType	1.3.6.1.4.1.14179.2.5.2.1.27	InetAddressType	read-create	The IP address of the RADIUS accounting server referred to in this table entry.
IP bsnRadiusAccServerInetAddress	1.3.6.1.4.1.14179.2.5.2.1.28	InetAddress	read-create	The IP address of the RADIUS accounting server referred to in this table entry.
bsnRadiusAuthServerStatsTable	1.3.6.1.4.1.14179.2.5.3		not-accessible	The listing the Statistics of RADIUS authentication servers.
bsnRadiusAuthServerStatsEntry	1.3.6.1.4.1.14179.2.5.3.1		not-accessible	An entry representing statistics a RADIUS authentication server with which the client shares a secret.
TIK bsnRadiusAuthClientRoundTripTime	1.3.6.1.4.1.14179.2.5.3.1.6	TimeTicks	read-only	The time interval (in hundredths of a second) between the most recent Access-Reply/Access-Challenge and the Access-Request that matched it from this RADIUS authentication server.
C32 bsnRadiusAuthClientAccessRequests	1.3.6.1.4.1.14179.2.5.3.1.7	Counter32	read-only	The number of RADIUS Access-Request packets sent to this server. This does not include retransmissions.
C32 bsnRadiusAuthClientAccessRetransmissions	1.3.6.1.4.1.14179.2.5.3.1.8	Counter32	read-only	The number of RADIUS Access-Request packets retransmitted to this RADIUS authentication server.
C32 bsnRadiusAuthClientAccessAccepts	1.3.6.1.4.1.14179.2.5.3.1.9	Counter32	read-only	The number of RADIUS Access-Accept packets (valid or invalid) received from this server.
C32 bsnRadiusAuthClientAccessRejects	1.3.6.1.4.1.14179.2.5.3.1.10	Counter32	read-only	The number of RADIUS Access-Reject packets (valid or invalid) received from this server.
C32 bsnRadiusAuthClientAccessChallenges	1.3.6.1.4.1.14179.2.5.3.1.11	Counter32	read-only	The number of RADIUS Access-Challenge packets (valid or invalid) received from this server.
C32 bsnRadiusAuthClientMalformedAccessResponses	1.3.6.1.4.1.14179.2.5.3.1.12	Counter32	read-only	The number of malformed RADIUS Access-Response packets received from this server. Malformed packets include packets with an invalid length. Bad authenticators or Signature attributes or unknown types are not included as malformed access responses.
C32 bsnRadiusAuthClientBadAuthenticators	1.3.6.1.4.1.14179.2.5.3.1.13	Counter32	read-only	The number of RADIUS Access-Response packets containing invalid authenticators or Signature attributes received from this server.
G32 bsnRadiusAuthClientPendingRequests	1.3.6.1.4.1.14179.2.5.3.1.14	Gauge32	read-only	The number of RADIUS Access-Request packets destined for this server that have not yet timed out or received a response. This variable is incremented when an Access-Request is sent and decremented due to receipt of an Acess-Accept, Access-Reject or Access-Challenge, a timeout or retransmission.
C32 bsnRadiusAuthClientTimeouts	1.3.6.1.4.1.14179.2.5.3.1.15	Counter32	read-only	The number of authentication timeouts to this server. After a timeout the client may retry to the same server, send to a different server, or give up. A retry to the same server is counted as a retransmit as well as a timeout. A send to a different server is counted as a Request as well as a timeout.
C32 bsnRadiusAuthClientUnknownTypes	1.3.6.1.4.1.14179.2.5.3.1.16	Counter32	read-only	The number of RADIUS packets of unknown type which were received from this server on the authentication port.
C32 bsnRadiusAuthClientPacketsDropped	1.3.6.1.4.1.14179.2.5.3.1.36	Counter32	read-only	The number of RADIUS packets of which were received from this server on the authentication port and dropped for some other reason.
bsnRadiusAccServerStatsTable	1.3.6.1.4.1.14179.2.5.4		not-accessible	The (conceptual) table listing the RADIUS accounting servers with which the client shares a secret.
bsnRadiusAccServerStatsEntry	1.3.6.1.4.1.14179.2.5.4.1		not-accessible	An entry (conceptual row) representing a RADIUS accounting server with which the client shares a secret.
TIK bsnRadiusAccClientRoundTripTime	1.3.6.1.4.1.14179.2.5.4.1.6	TimeTicks	read-only	The time interval between the most recent Accounting-Response and the Accounting-Request that matched it from this RADIUS accounting server.
C32 bsnRadiusAccClientRequests	1.3.6.1.4.1.14179.2.5.4.1.7	Counter32	read-only	The number of RADIUS Accounting-Request packets sent. This does not include retransmissions.
C32 bsnRadiusAccClientRetransmissions	1.3.6.1.4.1.14179.2.5.4.1.8	Counter32	read-only	The number of RADIUS Accounting-Request packets retransmitted to this RADIUS accounting server. Retransmissions include retries where the Identifier and Acct-Delay have been updated, as well as those in which they remain the same.
C32 bsnRadiusAccClientResponses	1.3.6.1.4.1.14179.2.5.4.1.9	Counter32	read-only	The number of RADIUS packets received on the accounting port from this server.
C32 bsnRadiusAccClientMalformedResponses	1.3.6.1.4.1.14179.2.5.4.1.10	Counter32	read-only	The number of malformed RADIUS Accounting-Response packets received from this server. Malformed packets include packets with an invalid length. Bad authenticators and unknown types are not included as malformed accounting responses.
C32 bsnRadiusAccClientBadAuthenticators	1.3.6.1.4.1.14179.2.5.4.1.11	Counter32	read-only	The number of RADIUS Accounting-Response packets which contained invalid authenticators received from this server.
G32 bsnRadiusAccClientPendingRequests	1.3.6.1.4.1.14179.2.5.4.1.12	Gauge32	read-only	The number of RADIUS Accounting-Request packets sent to this server that have not yet timed out or received a response. This variable is incremented when an Accounting-Request is sent and decremented due to receipt of an Accounting-Response, a timeout or a retransmission.
C32 bsnRadiusAccClientTimeouts	1.3.6.1.4.1.14179.2.5.4.1.13	Counter32	read-only	The number of accounting timeouts to this server. After a timeout the client may retry to the same server, send to a different server, or give up. A retry to the same server is counted as a retransmit as well as a timeout. A send to a different server is counted as an Accounting-Request as well as a timeout.
C32 bsnRadiusAccClientUnknownTypes	1.3.6.1.4.1.14179.2.5.4.1.14	Counter32	read-only	The number of RADIUS packets of unknown type which were received from this server on the accounting port.
C32 bsnRadiusAccClientPacketsDropped	1.3.6.1.4.1.14179.2.5.4.1.34	Counter32	read-only	The number of RADIUS packets which were received from this server on the accounting port and dropped for some other reason.
bsnUsersTable	1.3.6.1.4.1.14179.2.5.5		not-accessible	The (conceptual) table listing Wlan Users
bsnUsersEntry	1.3.6.1.4.1.14179.2.5.5.1		not-accessible	....
OCT bsnUserName	1.3.6.1.4.1.14179.2.5.5.1.2	OCTET STRING	read-create	User Name
OCT bsnUserPassword	1.3.6.1.4.1.14179.2.5.5.1.3	OCTET STRING	read-create	User Password
INT bsnUserEssIndex	1.3.6.1.4.1.14179.2.5.5.1.4	INTEGER	read-create	User WLAN ID. Value 0 implies that this applies to any WLAN ID.
INT bsnUserAccessMode	1.3.6.1.4.1.14179.2.5.5.1.5	INTEGER	read-create	User Access Mode.
INT bsnUserType	1.3.6.1.4.1.14179.2.5.5.1.6	INTEGER	read-create	User Type.
OCT bsnUserInterfaceName	1.3.6.1.4.1.14179.2.5.5.1.7	OCTET STRING	read-create	Interface Name.
ROW bsnUserRowStatus	1.3.6.1.4.1.14179.2.5.5.1.26	RowStatus	read-create	Row Status
bsnBlackListClientTable	1.3.6.1.4.1.14179.2.5.6		not-accessible	The table listing Wlan Black Listed Clients
bsnBlackListClientEntry	1.3.6.1.4.1.14179.2.5.6.1		not-accessible	....
OCT bsnBlackListClientMacAddress	1.3.6.1.4.1.14179.2.5.6.1.1	OCTET STRING	read-create	Black Listed Client MAC Address
OCT bsnBlackListClientDescription	1.3.6.1.4.1.14179.2.5.6.1.2	OCTET STRING	read-create	Black Listed Client Description
ROW bsnBlackListClientRowStatus	1.3.6.1.4.1.14179.2.5.6.1.22	RowStatus	read-create	Row Status
bsnAclTable	1.3.6.1.4.1.14179.2.5.7		not-accessible	The table listing ACLs (Access Control Lists) on the Switch.
bsnAclEntry	1.3.6.1.4.1.14179.2.5.7.1		not-accessible	....
OCT bsnAclName	1.3.6.1.4.1.14179.2.5.7.1.1	OCTET STRING	read-create	Name of the Access Control List.
INT bsnAclApplyMode	1.3.6.1.4.1.14179.2.5.7.1.2	INTEGER	read-only	The apply mode of the ACL on the switch. Mode value 'applied' means the ACL has been applied on the switch.
ROW bsnAclRowStatus	1.3.6.1.4.1.14179.2.5.7.1.20	RowStatus	read-create	Row Status of the ACL.
bsnAclRuleTable	1.3.6.1.4.1.14179.2.5.8		not-accessible	The table listing Acl Rules(Access Control List Entries) on the ACL with name bsnAclName.
bsnAclRuleEntry	1.3.6.1.4.1.14179.2.5.8.1		not-accessible	....
U32 bsnAclRuleIndex	1.3.6.1.4.1.14179.2.5.8.1.2	Unsigned32	read-create	Index of the ACL rule. This can be updated to reset the sequence of the rules of an ACL.
INT bsnAclRuleAction	1.3.6.1.4.1.14179.2.5.8.1.3	INTEGER	read-create	The permission mode of a rule.
INT bsnAclRuleDirection	1.3.6.1.4.1.14179.2.5.8.1.4	INTEGER	read-create	The direction of the packet to which the rule may be applied.
IP bsnAclRuleSourceIpAddress	1.3.6.1.4.1.14179.2.5.8.1.5	IpAddress	read-create	Source IP Address of the ACL rule. A value 0 implies any source address.
IP bsnAclRuleSourceIpNetmask	1.3.6.1.4.1.14179.2.5.8.1.6	IpAddress	read-create	Source IP Netmask of the ACL rule. A value 0 implies any source mask.
IP bsnAclRuleDestinationIpAddress	1.3.6.1.4.1.14179.2.5.8.1.7	IpAddress	read-create	Destination IP Address of the ACL rule. A value 0 implies any destination address.
IP bsnAclRuleDestinationIpNetmask	1.3.6.1.4.1.14179.2.5.8.1.8	IpAddress	read-create	Destination Netmask of the ACL rule. A value 0 implies any destination mask.
U32 bsnAclRuleProtocol	1.3.6.1.4.1.14179.2.5.8.1.9	Unsigned32	read-create	Protocol of the packet. It can be either of the pre specified protocols like TCP, UDP, ICMP, ESP, AH, GRE, IP, Ethernet Over IP, OSPF or any number between 0 and 255. A value 256 implies that this rule applies to 'Any' protocol.
U32 bsnAclRuleStartSourcePort	1.3.6.1.4.1.14179.2.5.8.1.10	Unsigned32	read-create	Source Port of the packet. It can be either of the pre specified ports like HTTP, HTTPS, Telnet, RADIUS etc or any number between 0 and 65535. A value 65536 implies that this rule applies to 'Any' source port. This value can be set only if the protocol is set to TCP or UDP. Otherwise the value is set to Any(65536)
U32 bsnAclRuleEndSourcePort	1.3.6.1.4.1.14179.2.5.8.1.11	Unsigned32	read-create	Source Port of the packet. It can be either of the pre specified ports like HTTP, HTTPS, Telnet, RADIUS etc or any number between 0 and 65535. A value 65536 implies that this rule applies to 'Any' source port. This value can be set only if the protocol is set to TCP or UDP. Otherwise the value is set to Any(65536)
U32 bsnAclRuleStartDestinationPort	1.3.6.1.4.1.14179.2.5.8.1.12	Unsigned32	read-create	Destination Port of the packet. It can be either of the pre specified ports like HTTP, HTTPS, Telnet, RADIUS etc or any number between 0 and 65535. A value 65536 implies that this rule aplpies to 'Any' Destination port. This value can be set only if the protocol is set to TCP or UDP. Otherwise the value is set to Any(65536)
U32 bsnAclRuleEndDestinationPort	1.3.6.1.4.1.14179.2.5.8.1.13	Unsigned32	read-create	Destination Port of the packet. It can be either of the pre specified ports like HTTP, HTTPS, Telnet, RADIUS etc or any number between 0 and 65535. A value 65536 implies that this rule aplpies to 'Any' Destination port. This value can be set only if the protocol is set to TCP or UDP. Otherwise the value is set to Any(65536)
U32 bsnAclRuleDscp	1.3.6.1.4.1.14179.2.5.8.1.14	Unsigned32	read-create	DSCP value of the rule. A value 256 implies Any
U32 bsnAclNewRuleIndex	1.3.6.1.4.1.14179.2.5.8.1.15	Unsigned32	read-create	New Index of the ACL rule. This attribute should be updated if the requirement is to reset the sequence of the rules of an ACL. A read on this will not yield anything.
ROW bsnAclRuleRowStatus	1.3.6.1.4.1.14179.2.5.8.1.40	RowStatus	read-create	Row Status of the ACL Rule.
bsnMacFilterTable	1.3.6.1.4.1.14179.2.5.9		not-accessible	The table listing MAC Filter entries
bsnMacFilterEntry	1.3.6.1.4.1.14179.2.5.9.1		not-accessible	....
OCT bsnMacFilterAddress	1.3.6.1.4.1.14179.2.5.9.1.1	OCTET STRING	read-create	MAC Address of the entry
INT bsnMacFilterWlanId	1.3.6.1.4.1.14179.2.5.9.1.2	INTEGER	read-create	WLAN ID of the WLAN that the user can connect to. 0 means any WLAN ID.
OCT bsnMacFilterInterfaceName	1.3.6.1.4.1.14179.2.5.9.1.3	OCTET STRING	read-create	Interface Name.
OCT bsnMacFilterDescription	1.3.6.1.4.1.14179.2.5.9.1.4	OCTET STRING	read-create	Description of the MAC Filter entry.
ROW bsnMacFilterRowStatus	1.3.6.1.4.1.14179.2.5.9.1.24	RowStatus	read-create	Row Status
bsnLocalNetUserTable	1.3.6.1.4.1.14179.2.5.10		not-accessible	The table listing Local Net User entries.
bsnLocalNetUserEntry	1.3.6.1.4.1.14179.2.5.10.1		not-accessible	....
OCT bsnLocalNetUserName	1.3.6.1.4.1.14179.2.5.10.1.1	OCTET STRING	read-create	Name of the net user.
INT bsnLocalNetUserWlanId	1.3.6.1.4.1.14179.2.5.10.1.2	INTEGER	read-create	WLAN ID of the WLAN that the user can connect to. 0 means any WLAN ID.
OCT bsnLocalNetUserPassword	1.3.6.1.4.1.14179.2.5.10.1.3	OCTET STRING	read-create	User Password.
OCT bsnLocalNetUserDescription	1.3.6.1.4.1.14179.2.5.10.1.4	OCTET STRING	read-create	Description of the Net User entry.
NUM bsnLocalNetUserLifetime	1.3.6.1.4.1.14179.2.5.10.1.5	TimeInterval	read-create	This object indicates the lifetime of an user account expressed in hundredths of a second. Lifetime period other than 0 will make it a guest-user. Minimum value for guest user is 60 seconds (6000). Once configured as non-guest user can not be change to guest user and vice-versa. Default value is for a day and max lifetime is 259200000(30 days). WLANIds, which have webauth policy are valid for guest access user.
TIK bsnLocalNetUserStartTime	1.3.6.1.4.1.14179.2.5.10.1.6	TimeTicks	read-only	This object indicates the time when the guest user account was created and expressed as the number of seconds elapsed since 1st Jan, 1970.
NUM bsnLocalNetUserRemainingTime	1.3.6.1.4.1.14179.2.5.10.1.7	TimeInterval	read-only	This object indicates the remaining session time for the guest user in hundredths of a second.
ROW bsnLocalNetUserRowStatus	1.3.6.1.4.1.14179.2.5.10.1.24	RowStatus	read-create	Row Status
bsnLocalManagementUserTable	1.3.6.1.4.1.14179.2.5.11		not-accessible	The (conceptual) table listing Local Management Users
bsnLocalManagementUserEntry	1.3.6.1.4.1.14179.2.5.11.1		not-accessible	....
OCT bsnLocalManagementUserName	1.3.6.1.4.1.14179.2.5.11.1.1	OCTET STRING	read-create	User Name
OCT bsnLocalManagementUserPassword	1.3.6.1.4.1.14179.2.5.11.1.2	OCTET STRING	read-create	User Password
INT bsnLocalManagementUserAccessMode	1.3.6.1.4.1.14179.2.5.11.1.3	INTEGER	read-create	User Access Mode.
ROW bsnLocalManagementUserRowStatus	1.3.6.1.4.1.14179.2.5.11.1.23	RowStatus	read-create	Row Status
T/F bsnRadiusAuthKeyWrapEnable	1.3.6.1.4.1.14179.2.5.12	TruthValue	read-write	When keyWrap is enable then for 801.1X and 802.11i client Authentication, request is sent to those radius servers which has KEK and MACK keys are configured. Radius servers are widely used for user authentications. In 802.11i and 802.1X type authentication, the controller recives Pairwise Master KEy(PMK) from RADIUS sever using vendor specific RADIUS attributes, which uses MPPE RFC3078. Since MPPE uses RC4 algorithm to provide data confidentiality, it is not FIPS approved. For this RADIUS key WRAP attributes, bsnRadiusAuthServerKeyWrap and bsnRadiusAuthServerKeyWrapMACKkey have been added, which are used to securely transfer encryption keys using non-proprietary techniques.
INT bsnRadiusAuthCacheCredentialsLocally	1.3.6.1.4.1.14179.2.5.14	INTEGER	read-write	Enable or disable caching of credentials locally for RADIUS Auth servers. This is used when a client uses a one time password authentication scheme.
INT bsnAAAMacDelimiter	1.3.6.1.4.1.14179.2.5.15	INTEGER	read-write	The delimiter to be used for mac filtering. It can be colon as in xx:xx:xx:xx:xx:xx or hyphen as in xx-xx-xx-xx-xx-xx or single hyphen as in xxxxxx-xxxxxx or no delimiter as in xxxxxxxxxxxx.
INT bsnAAARadiusCompatibilityMode	1.3.6.1.4.1.14179.2.5.16	INTEGER	read-write	The required compatibility mode for MAC filtering. For ciscoACS, the expected MAC delimiter setting is colon and for orinocoRadius, it is singleHyphen.
INT bsnAAARadiusCallStationIdType	1.3.6.1.4.1.14179.2.5.17	INTEGER	read-write	This attribute configures the call station ID information sent in RADIUS messages. The value undefined cannot be set during the write operation.
STR bsnExternalPolicyServerAclName	1.3.6.1.4.1.14179.2.5.18	DisplayString	read-write	This attribute configures the ACL Name for External Policy Servers
bsnExternalPolicyServerTable	1.3.6.1.4.1.14179.2.5.19		not-accessible	The (conceptual) table listing the External Policy servers with which client share a secret.
bsnExternalPolicyServerEntry	1.3.6.1.4.1.14179.2.5.19.1		not-accessible	An entry (conceptual row) representing an External policy server with which the client shares a secret.
I32 bsnExternalPolicyServerIndex	1.3.6.1.4.1.14179.2.5.19.1.1	Integer32	read-create	A number uniquely identifying each External Policy server with which this client communicates.
IP bsnExternalPolicyServerAddress	1.3.6.1.4.1.14179.2.5.19.1.2	IpAddress	read-create	The IP address of the External Policy server referred to in this table entry.
I32 bsnExternalPolicyServerPortNumber	1.3.6.1.4.1.14179.2.5.19.1.3	Integer32	read-create	The UDP port the client is using to send requests to this server.
OCT bsnExternalPolicyServerKey	1.3.6.1.4.1.14179.2.5.19.1.4	OCTET STRING	read-create	The authentication and encryption key shared between the client and this External Policy Server.
INT bsnExternalPolicyServerAdminStatus	1.3.6.1.4.1.14179.2.5.19.1.5	INTEGER	read-create	Server enable or disable status.
INT bsnExternalPolicyServerConnectionStatus	1.3.6.1.4.1.14179.2.5.19.1.6	INTEGER	read-only	Server enable or disable status.
ROW bsnExternalPolicyServerRowStatus	1.3.6.1.4.1.14179.2.5.19.1.26	RowStatus	read-create	Row Status for creation/deletion
I32 bsnAAALocalDatabaseSize	1.3.6.1.4.1.14179.2.5.20	Integer32	read-write	This attribute is the total number of entries permitted in the local users database. This is the combined total of entries for Local Management Users, Local Net Users, Disabled Clients (previously known as blacklistclients and the MAC Filters. If the database size limit is reached, no more entries in any of these user lists are allowed to be created. To continue creating more entries, one should increase the size of the database. This value is applied on reboot and then matches the bsnAACurrentLocalDatabaseSize.
I32 bsnAAACurrentLocalDatabaseSize	1.3.6.1.4.1.14179.2.5.21	Integer32	read-only	This attribute is the maximum number of entries in the local users database that is effective currently. This is the combined total of entries for Local Management Users, Local Net Users, Disabled Clients (previously known as blacklist clients) and the MAC Filters.
bsnAPAuthorizationTable	1.3.6.1.4.1.14179.2.5.22		not-accessible	The table listing AP Authorization entries
bsnAPAuthorizationEntry	1.3.6.1.4.1.14179.2.5.22.1		not-accessible	BsnAPAuthorizationEntry
OCT bsnAPAuthMacAddress	1.3.6.1.4.1.14179.2.5.22.1.1	OCTET STRING	read-create	MAC Address of the AP entry
INT bsnAPAuthCertificateType	1.3.6.1.4.1.14179.2.5.22.1.2	INTEGER	read-create	Supported certificate types are MIC, SSC (Self-Signed-Certificate) or no certificate.
OCT bsnAPAuthHashKey	1.3.6.1.4.1.14179.2.5.22.1.3	OCTET STRING	read-create	SHA1 hash key for SSC certificate validation. It has to be 40/64 hexa-decimal characters. This is considered when certificate type is SSC.
ROW bsnAPAuthRowStatus	1.3.6.1.4.1.14179.2.5.22.1.20	RowStatus	read-create	Row Status
bsnTrap	1.3.6.1.4.1.14179.2.6
bsnTrapControl	1.3.6.1.4.1.14179.2.6.1
U32 bsnDot11StationTrapControlMask	1.3.6.1.4.1.14179.2.6.1.1	Unsigned32	read-write	This mask describes what events merit traps to network management. If the bit for a particular event is turned on then notification will be generated on event occurence. Event corresponding value ----- ----------------- bsnDot11StationDisassociate 1 bsnDot11StationDeauthenticate 2 bsnDot11StationAuthenticateFail 4 bsnDot11StationAssociateFail 8 bsnDot11StationBlacklisted 16 bsnDot11StationAssociate 32 ciscoLwappDot11ClientMovedToRunState 64 By Default all bits are off.
U32 bsnAPTrapControlMask	1.3.6.1.4.1.14179.2.6.1.2	Unsigned32	read-write	This mask describes what events merit traps to network management. If the bit for a particular event is turned on then notification will be generated on event occurance. Event corresponding bit ----- ----------------- bsnAPAssociate/Disassociate 1 bsnAPIfUp/Down 4 bsnAPAuthorizationFailureCause 16 bsnAPModeChanged 32 bsnAPTimeSyncFailure 64 By Default all bits are on.
U32 bsnAPProfileTrapControlMask	1.3.6.1.4.1.14179.2.6.1.3	Unsigned32	read-write	This mask describes what events merit traps to network management. If the bit for a particular event is turned on then notification will be generated on event occurance. Event corresponding bit ----- ----------------- LoadProfileFail 1 NoiseProfileFail 2 InterferenceProfileFail 4 CoverageProfileFailed 8
U32 bsnAPParamUpdateTrapControlMask	1.3.6.1.4.1.14179.2.6.1.4	Unsigned32	read-write	Mac Parameters are updated for a Airespace AP interface whenever Dynamic Algorithm are run. This mask describes what update events merit traps to network management. If the bit for a particular event is turned on then notification will be generated on event occurance. Event corresponding bit ----- ----------------- TxPowerChange 1 ChannelChange 2 AntennaChange 4 RTSCTSThresholdChange 8 EDThresholdChange 16 FragmentationThresholdChange 32
U32 bsnIpsecTrapsMask	1.3.6.1.4.1.14179.2.6.1.5	Unsigned32	read-write	This mask describes what events merit traps to network management. If the bit for a particular event is turned on then notification will be generated on event occurance. Event corresponding bit ----- ----------------- bsnIpsecEspAuthFailureTrap 1 bsnIpsecEspReplayFailureTrap 2 bsnIpsecEspPolicyFailureTrap 4 bsnIpsecEspInvalidSpiTrap 8 bsnIpsecOtherPolicyFailureTrap 16 bsnIpsecIkeNegFailure 32 bsnIpsecSuiteNegFailure 64 bsnIpsecInvalidCookieTrap 128
INT bsnRogueAPTrapEnable	1.3.6.1.4.1.14179.2.6.1.6	INTEGER	read-write	If Rogue AP Detection and Removed Traps need to be sent
INT bsnRADIUSServerTrapEnable	1.3.6.1.4.1.14179.2.6.1.7	INTEGER	read-write	if RADIUS Server Traps need to be sent
INT bsnAuthenticationFailureTrapEnable	1.3.6.1.4.1.14179.2.6.1.8	INTEGER	read-write	If Authentication Failure Traps need to be sent
INT bsnConfigSaveTrapEnable	1.3.6.1.4.1.14179.2.6.1.9	INTEGER	read-write	If Rogue AP Detection and Removed Traps need to be sent
U32 bsn80211SecurityTrapControlMask	1.3.6.1.4.1.14179.2.6.1.10	Unsigned32	read-write	This mask is for Security related trap controls. Event corresponding bit ----- ----------------- bsnWepKeyDecryptError 1 bsnSignatureAttackDetected 2 By Default all bits are off.
INT bsnWpsTrapControlEnable	1.3.6.1.4.1.14179.2.6.1.11	INTEGER	read-write	This control is for WPS(Wireless Intrusion Protection System) related traps.
bsnTrapVariable	1.3.6.1.4.1.14179.2.6.2
OCT bsnAuthFailureUserName	1.3.6.1.4.1.14179.2.6.2.1	OCTET STRING	accessible-for-notify
INT bsnAuthFailureUserType	1.3.6.1.4.1.14179.2.6.2.2	INTEGER	accessible-for-notify
IP bsnRemoteIPv4Address	1.3.6.1.4.1.14179.2.6.2.3	IpAddress	accessible-for-notify
I32 bsnIpsecErrorCount	1.3.6.1.4.1.14179.2.6.2.4	Integer32	accessible-for-notify
I32 bsnIpsecSPI	1.3.6.1.4.1.14179.2.6.2.5	Integer32	accessible-for-notify
I32 bsnRemoteUdpPort	1.3.6.1.4.1.14179.2.6.2.6	Integer32	accessible-for-notify
I32 bsnIkeAuthMethod	1.3.6.1.4.1.14179.2.6.2.7	Integer32	accessible-for-notify
I32 bsnIkeTotalInitFailures	1.3.6.1.4.1.14179.2.6.2.8	Integer32	accessible-for-notify
I32 bsnIkeTotalInitNoResponses	1.3.6.1.4.1.14179.2.6.2.9	Integer32	accessible-for-notify
I32 bsnIkeTotalRespFailures	1.3.6.1.4.1.14179.2.6.2.10	Integer32	accessible-for-notify
I32 bsnNotifiesSent	1.3.6.1.4.1.14179.2.6.2.11	Integer32	accessible-for-notify
I32 bsnNotifiesReceived	1.3.6.1.4.1.14179.2.6.2.12	Integer32	accessible-for-notify
I32 bsnSuiteInitFailures	1.3.6.1.4.1.14179.2.6.2.13	Integer32	accessible-for-notify
I32 bsnSuiteRespondFailures	1.3.6.1.4.1.14179.2.6.2.14	Integer32	accessible-for-notify
OCT bsnInitiatorCookie	1.3.6.1.4.1.14179.2.6.2.15	OCTET STRING	accessible-for-notify	The initiator cookie used in an ISAKMP message, to be associated with a trap.
OCT bsnResponderCookie	1.3.6.1.4.1.14179.2.6.2.16	OCTET STRING	accessible-for-notify	The responder cookie used in an ISAKMP message, to be associated with a trap.
I32 bsnIsakmpInvalidCookies	1.3.6.1.4.1.14179.2.6.2.17	Integer32	accessible-for-notify
I32 bsnCurrentRadiosCount	1.3.6.1.4.1.14179.2.6.2.18	Integer32	accessible-for-notify
I32 bsnLicenseRadioCount	1.3.6.1.4.1.14179.2.6.2.19	Integer32	accessible-for-notify
MAC bsnAPMacAddrTrapVariable	1.3.6.1.4.1.14179.2.6.2.20	MacAddress	accessible-for-notify
STR bsnAPNameTrapVariable	1.3.6.1.4.1.14179.2.6.2.21	DisplayString	accessible-for-notify
I32 bsnAPSlotIdTrapVariable	1.3.6.1.4.1.14179.2.6.2.22	Integer32	accessible-for-notify	Number of Radio Interfaces on the Airespace AP.
I32 bsnAPChannelNumberTrapVariable	1.3.6.1.4.1.14179.2.6.2.23	Integer32	accessible-for-notify
I32 bsnAPCoverageThresholdTrapVariable	1.3.6.1.4.1.14179.2.6.2.24	Integer32	accessible-for-notify
I32 bsnAPCoverageFailedClients	1.3.6.1.4.1.14179.2.6.2.25	Integer32	accessible-for-notify
I32 bsnAPCoverageTotalClients	1.3.6.1.4.1.14179.2.6.2.26	Integer32	accessible-for-notify
MAC bsnClientMacAddr	1.3.6.1.4.1.14179.2.6.2.27	MacAddress	accessible-for-notify
I32 bsnClientRssi	1.3.6.1.4.1.14179.2.6.2.28	Integer32	accessible-for-notify
I32 bsnClientSnr	1.3.6.1.4.1.14179.2.6.2.29	Integer32	accessible-for-notify
I32 bsnInterferenceEnergyBeforeChannelUpdate	1.3.6.1.4.1.14179.2.6.2.30	Integer32	accessible-for-notify
I32 bsnInterferenceEnergyAfterChannelUpdate	1.3.6.1.4.1.14179.2.6.2.31	Integer32	accessible-for-notify
I32 bsnAPPortNumberTrapVariable	1.3.6.1.4.1.14179.2.6.2.32	Integer32	accessible-for-notify
I32 bsnMaxRogueCount	1.3.6.1.4.1.14179.2.6.2.33	Integer32	accessible-for-notify
MAC bsnStationMacAddress	1.3.6.1.4.1.14179.2.6.2.34	MacAddress	accessible-for-notify
MAC bsnStationAPMacAddr	1.3.6.1.4.1.14179.2.6.2.35	MacAddress	accessible-for-notify
INT bsnStationAPIfSlotId	1.3.6.1.4.1.14179.2.6.2.36	INTEGER	accessible-for-notify
INT bsnStationReasonCode	1.3.6.1.4.1.14179.2.6.2.37	INTEGER	accessible-for-notify	unspecified - Unspecified. previousAuthNotValid - Previous Authentication was not valid. deauthenticationLeaving - Leaving due to deauthentication. disassociationDueToInactivity - Disassociation due to Inactivity. disassociationAPBusy - Disassociation since AP was busy. class2FrameFromNonAuthStation - Class 2 frame from non authenticated station. class2FrameFromNonAssStation - Class 2 frame from non associated station. disassociationStaHasLeft - Station has left due to disassociation. staReqAssociationWithoutAuth - Station send association request without authentication. invalidInformationElement - Invalid information element. groupCipherInvalid - Invalid group Cipher. unicastCipherInvalid - Invalid unicast cipher. akmpInvalid - Invalid AKMP. unsupportedRsnVersion - Unsupported RSN version. invalidRsnIeCapabilities - Invalid RSN IE capabilities. cipherSuiteRejected - Cipher suite rejected. missingReasonCode - Reason code is missing. maxAssociatedClientsReached - Maximum allowed associated client number has reached. maxAssociatedClientsReachedOnRadio - Maximum allowed associated client number has reached on radio. maxAssociatedClientsReachedOnWlan - Maximum allowed associated client number has reached on wlan. unSpecifiedQosFailure - Unsupported QOS failure. qosPolicyMismatch - Mismatch on QOS policy. inSufficientBandwidth - Insufficient bandwidth. inValidQosParams - Invalid QOS parameters.
INT bsnStationBlacklistingReasonCode	1.3.6.1.4.1.14179.2.6.2.38	INTEGER	accessible-for-notify
STR bsnStationUserName	1.3.6.1.4.1.14179.2.6.2.39	DisplayString	accessible-for-notify	The user name of a client. This is used for the Client Associated trap. It may be null when not known.
INT bsnRogueAPOnWiredNetwork	1.3.6.1.4.1.14179.2.6.2.40	INTEGER	accessible-for-notify	This is the flag used on the bsnRogueAPDetected trap to state if the rogue is found on the wired network. Typically, after a rogue is found, there may be another bsnRogueAPDetected trap that will have the value of this flag 1 if the rogue is detected on the wired network.
MAC bsnNavDosAttackSourceMacAddr	1.3.6.1.4.1.14179.2.6.2.41	MacAddress	accessible-for-notify	MAC address generating the attack.
INT bsnWlanIdTrapVariable	1.3.6.1.4.1.14179.2.6.2.42	INTEGER	accessible-for-notify	WLAN ID used by the client when the WPA MIC error counter measure was activated.
IP bsnUserIpAddress	1.3.6.1.4.1.14179.2.6.2.43	IpAddress	accessible-for-notify
INT bsnRogueAdhocMode	1.3.6.1.4.1.14179.2.6.2.44	INTEGER	accessible-for-notify	This is the flag used on the bsnRogueAPDetected trap to state if the rogue found is an Adhoc rogue or it is an AP.
INT bsnClearTrapVariable	1.3.6.1.4.1.14179.2.6.2.45	INTEGER	accessible-for-notify	This is the flag is used to indicate if this is a clear trap for the original alert or not.
IP bsnDuplicateIpTrapVariable	1.3.6.1.4.1.14179.2.6.2.46	IpAddress	accessible-for-notify	This field is used on the bsnDuplicateIpAddressReported trap to contain the IP Address in question when switch or an AP detected a duplicate IP Address on another machine.
INT bsnDuplicateIpTrapClear	1.3.6.1.4.1.14179.2.6.2.47	INTEGER	accessible-for-notify	This is the flag used to indicate clear state for the bsnDuplicateIpAddressReported trap.
INT bsnDuplicateIpReportedByAP	1.3.6.1.4.1.14179.2.6.2.48	INTEGER	accessible-for-notify	This is the flag used on the bsnDuplicateIpAddressReported trap to indicate whether the switch or an AP detected a duplicate IP Address on another machine.
INT bsnTrustedApRadioPolicyRequired	1.3.6.1.4.1.14179.2.6.2.49	INTEGER	accessible-for-notify	This is the radio policy required by a trusted Rogue.
INT bsnTrustedApEncryptionUsed	1.3.6.1.4.1.14179.2.6.2.50	INTEGER	accessible-for-notify	This is the encryption type used by a trusted Rogue.
INT bsnTrustedApEncryptionRequired	1.3.6.1.4.1.14179.2.6.2.51	INTEGER	accessible-for-notify	This is the encryption type required by a trusted Rogue.
INT bsnTrustedApRadioPolicyUsed	1.3.6.1.4.1.14179.2.6.2.52	INTEGER	accessible-for-notify	This is the radio policy used by a trusted Rogue.
INT bsnNetworkType	1.3.6.1.4.1.14179.2.6.2.53	INTEGER	accessible-for-notify
INT bsnNetworkState	1.3.6.1.4.1.14179.2.6.2.54	INTEGER	accessible-for-notify
INT bsnSignatureType	1.3.6.1.4.1.14179.2.6.2.55	INTEGER	accessible-for-notify	Type of Signature whose attack is detected by the switch.
STR bsnSignatureName	1.3.6.1.4.1.14179.2.6.2.56	DisplayString	accessible-for-notify	Name of the Signature whose attack is detected by the switch.
STR bsnSignatureDescription	1.3.6.1.4.1.14179.2.6.2.57	DisplayString	accessible-for-notify	Description of the Signature whose attack is detected by the switch.
MAC bsnImpersonatedAPMacAddr	1.3.6.1.4.1.14179.2.6.2.58	MacAddress	accessible-for-notify	MAC Address of the AP impersonated by another AP.
INT bsnTrustedApPreambleUsed	1.3.6.1.4.1.14179.2.6.2.59	INTEGER	accessible-for-notify	The Preamble on this detecting AP.
INT bsnTrustedApPreambleRequired	1.3.6.1.4.1.14179.2.6.2.60	INTEGER	accessible-for-notify	The Preamble on this detecting AP.
INT bsnSignatureAttackPreced	1.3.6.1.4.1.14179.2.6.2.61	INTEGER	accessible-for-notify	The preced in the standard/custom signature list.
INT bsnSignatureAttackFrequency	1.3.6.1.4.1.14179.2.6.2.62	INTEGER	accessible-for-notify	The preced in the standard/custom signature list.
INT bsnSignatureAttackChannel	1.3.6.1.4.1.14179.2.6.2.63	INTEGER	accessible-for-notify	The preced in the standard/custom signature list.
MAC bsnSignatureAttackerMacAddress	1.3.6.1.4.1.14179.2.6.2.64	MacAddress	accessible-for-notify	The MAC address of the Attacker's mac-interface.
OCT bsnLicenseKeyTrapVariable	1.3.6.1.4.1.14179.2.6.2.65	OCTET STRING	accessible-for-notify	This is the license key that has been found to be deleted, expired or is mismatched causing AP functionality to be disabled on the switch.
INT bsnApFunctionalityDisableReasonCode	1.3.6.1.4.1.14179.2.6.2.66	INTEGER	accessible-for-notify	This is the reason why the AP functionality was disabled on the switch. It could be either expiry or deletion or mismatch found of the license key.
INT bsnLicenseKeyFeatureSetTrapVariable	1.3.6.1.4.1.14179.2.6.2.67	INTEGER	accessible-for-notify	This is the switch feature set whose license key has expired or is deleted or is mismatched. To enable the AP functionality again, the license key for this feature set should be re-configured.
INT bsnApRegulatoryDomain	1.3.6.1.4.1.14179.2.6.2.68	INTEGER	accessible-for-notify	The regulatory domain configured on an AP.
INT bsnAPAuthorizationFailureCause	1.3.6.1.4.1.14179.2.6.2.69	INTEGER	accessible-for-notify	This denotes the reason for AP authorization failure. [entrydoesnotexist]: The AP has not been added to Controller's AP Authorization List. [keymismatch]: The key entry in Controller's AP Authorization list does not match the SHA1 key received from the AP. [invalidCert]: Could not verify the self signed Certificate. [entryIsMIC]: AP has Self Signed Certificate where as in Controller AP Authorization list has Manufactured Installed Certificate [aaaEntryDoesNotExist]: RADIUS authorization for the AP failed. [unknown]: Default.
INT bsnAPIfUpDownCause	1.3.6.1.4.1.14179.2.6.2.70	INTEGER	accessible-for-notify	This denotes the reason for AP If up or down normal - radio Failure - radio failed radioLowPower - AP is not able draw enough power. maxRetransmission - max retransmission of AP Reached. echoTimeout - heartbeat timeout. configAP - admin enable/disable AP configRadio - admin enable/disable config radio configNetwork - admin enable/disable network adminConfigured - admin configuration missedRekey - Missed Rekey detectingInLinePower - Detecting in-line power newDiscovery - New Discovery
INT bsnAPInvalidRadioType	1.3.6.1.4.1.14179.2.6.2.71	INTEGER	accessible-for-notify	Radio types which are not supported by controller.
OCT locationNotifyContent	1.3.6.1.4.1.14179.2.6.2.72	OCTET STRING	accessible-for-notify	This is the content of the notification.
BSN bsnSignatureMacInfo	1.3.6.1.4.1.14179.2.6.2.73	BsnTxtSignatureMacInfo	accessible-for-notify	This object defines the pattern followed by the LWAPP APs to perform signature analysis with this signature and report the results to the Controller.
MAC bsnImpersonatingSourceMacAddr	1.3.6.1.4.1.14179.2.6.2.74	MacAddress	accessible-for-notify	This is the source mac address which is impersonating the AP.
I32 bsnAPPreviousChannelNumberTrapVariable	1.3.6.1.4.1.14179.2.6.2.83	Integer32	accessible-for-notify
BIT bsnAPReasonCodeTrapVariable	1.3.6.1.4.1.14179.2.6.2.84	Bits	accessible-for-notify
I32 bsnNoiseBeforeChannelUpdate	1.3.6.1.4.1.14179.2.6.2.85	Integer32	accessible-for-notify
I32 bsnNoiseAfterChannelUpdate	1.3.6.1.4.1.14179.2.6.2.86	Integer32	accessible-for-notify
I32 bsnInterferenceBeforeChannelUpdate	1.3.6.1.4.1.14179.2.6.2.87	Integer32	accessible-for-notify
I32 bsnInterferenceAfterChannelUpdate	1.3.6.1.4.1.14179.2.6.2.88	Integer32	accessible-for-notify
bsnTraps	1.3.6.1.4.1.14179.2.6.3
NTF bsnDot11StationDisassociate	1.3.6.1.4.1.14179.2.6.3.1			The disassociate notification shall be sent when the Station sends a Disassociation frame. The value of the notification shall include the MAC address of the MAC to which the Disassociation frame was sent and the reason for the disassociation
NTF bsnDot11StationDeauthenticate	1.3.6.1.4.1.14179.2.6.3.2			The deauthenticate notification shall be sent when the Station sends a Deauthentication frame. The value of the notification shall include the MAC address of the MAC to which the Deauthentication frame was sent and the reason for the deauthentication.
NTF bsnDot11StationAuthenticateFail	1.3.6.1.4.1.14179.2.6.3.3			The authenticate failure notification shall be sent when the Station sends an Authentication frame with a status code other than 'successful'. The value of the notification shall include the MAC address of the MAC to which the Authentication frame was sent and the reason for the authentication failure.
NTF bsnDot11StationAssociateFail	1.3.6.1.4.1.14179.2.6.3.4			The associate failure notification shall be sent when the Station sends an Association frame with a status code other than 'successful'. The value of the notification shall include the MAC address of the MAC to which the Authentication frame was sent and the reason for the authentication failure.
NTF bsnAPUp	1.3.6.1.4.1.14179.2.6.3.5			When Airespace AP operation status goes up this trap will be sent
NTF bsnAPDown	1.3.6.1.4.1.14179.2.6.3.6			When Airespace AP operation status goes down this trap will be sent
NTF bsnAPAssociated	1.3.6.1.4.1.14179.2.6.3.7			When Airespace AP Associates to a Airespace Switch, AP associated notification will be sent with dot3 MAC address of Airespace AP.This will help management system to discover Airespace AP and add to system.
NTF bsnAPDisassociated	1.3.6.1.4.1.14179.2.6.3.8			When Airespace AP disassociates from Airespace Switch, AP disassociated notification will be sent with dot3 MAC address of Airespace AP management system to remove Airespace AP from this Airespace Switch
NTF bsnAPIfUp	1.3.6.1.4.1.14179.2.6.3.9			When Airespace AP's interface's operation status goes up this trap will be sent
NTF bsnAPIfDown	1.3.6.1.4.1.14179.2.6.3.10			When Airespace AP's interface's operation status goes down this trap will be sent.
NTF bsnAPLoadProfileFailed	1.3.6.1.4.1.14179.2.6.3.11			When LOAD Profile state changes from PASS to FAIL, notification will be sent with Dot3 MAC address of Airespace AP and slot ID of Airespace AP IF. This trap sending can be enable/disable using bsnRrmProfileTrapControlFlag
NTF bsnAPNoiseProfileFailed	1.3.6.1.4.1.14179.2.6.3.12			When Noise Profile state changes from PASS to FAIL, notification will be sent with Dot3 MAC address of Airespace AP and slot ID of Airespace AP IF. This trap sending can be enable/disable using bsnRrmProfileTrapControlFlag
NTF bsnAPInterferenceProfileFailed	1.3.6.1.4.1.14179.2.6.3.13			When Interference Profile state changes from PASS to FAIL, notification will be sent with Dot3 MAC address of Airespace AP and slot ID of Airespace AP IF. This trap sending can be enable/disable using bsnRrmProfileTrapControlFlag
NTF bsnAPCoverageProfileFailed	1.3.6.1.4.1.14179.2.6.3.14			When Coverage Profile state changes from PASS to FAIL, notification will be sent with Dot3 MAC address of Airespace AP and slot ID of Airespace AP IF. This trap sending can be enable/disable using bsnRrmProfileTrapControlFlag
NTF bsnAPCurrentTxPowerChanged	1.3.6.1.4.1.14179.2.6.3.15			Whenever dynamic algorithms are running and bsnAPIfPhyPowerAutomaticOn is true, Airespace AP Interface's CurrentTxPower might get updated by algorithm. When this occurs notification will be sent with Dot3 MAC address of Airespace AP and slot ID of Airespace AP IF along with the currentTxPower for this Airespace AP IF
NTF bsnAPCurrentChannelChanged	1.3.6.1.4.1.14179.2.6.3.16			Whenever dynamic algorithms are running and bsnAPIfPhyChannelAutomaticOn is true, Airespace AP Interface's CurrentChannel might get updated by algorithm. When this occurs notification will be sent with Dot3 MAC address of Airespace AP and slot ID of Airespace AP IF along with the currentChannel for this Airespace AP IF
NTF bsnRrmDot11aGroupingDone	1.3.6.1.4.1.14179.2.6.3.21			When Grouping is done, this notification will be sent from the previous Group Leader where grouping algorithm was run. It has MAC address of the new Group Leader.
NTF bsnRrmDot11bGroupingDone	1.3.6.1.4.1.14179.2.6.3.22			When Grouping is done, this notification will be sent from the previous Group Leader where grouping algorithm was run. It has MAC address of the new Group Leader.
NTF bsnConfigSaved	1.3.6.1.4.1.14179.2.6.3.23			When configuration is save either from CLI or web interface This trap will be sent to inform NMS to do refresh
NTF bsnDot11EssCreated	1.3.6.1.4.1.14179.2.6.3.24			Whenever a new Ess (WLAN) is created, this notification will be sent along with EssIndex
NTF bsnDot11EssDeleted	1.3.6.1.4.1.14179.2.6.3.25			Whenever a Ess (WLAN)is deleted, this notification will be sent along with EssIndex
NTF bsnRADIUSServerNotResponding	1.3.6.1.4.1.14179.2.6.3.26			This trap is to indicate that no RADIUS server(s) are responding to authentication requests sent by the RADIUS client within the MWAR device(Switch).
NTF bsnAuthenticationFailure	1.3.6.1.4.1.14179.2.6.3.27			This trap is to inform that client authentication failure has occured at MWAR(Switch). This could be cli/web user, wlan user, or Mac Authorized user. ServiceType will indicate which type of user it is and userName will be cli/web/wlan userName or MacAddress of Mac Authorized User
NTF bsnIpsecEspAuthFailureTrap	1.3.6.1.4.1.14179.2.6.3.28			IPsec packets with invalid hashes were found in an inbound ESP SA. The total number of authentication errors accumulated is sent for the specific row of the ipsecSaEspInTable table for the SA; this provides the identity of the SA in which the error occurred. Implementations SHOULD send one trap per SA (within a reasonable time period), rather than sending one trap per packet.
NTF bsnIpsecEspReplayFailureTrap	1.3.6.1.4.1.14179.2.6.3.29			IPsec packets with invalid sequence numbers were found in an inbound ESP SA. The total number of replay errors accumulated is sent for the specific row of the ipsecSaEspInTable table for the SA; this provides the identity of the SA in which the error occurred. Implementations SHOULD send one trap per SA (within a reasonable time period), rather than sending one trap per packet.
NTF bsnIpsecEspInvalidSpiTrap	1.3.6.1.4.1.14179.2.6.3.31			A packet with an unknown SPI was detected from the specified peer with the specified SPI using the specified protocol. The destination address of the received packet is specified by ipsecLocalAddress. The value ifIndex may be 0 if this optional linkage is unsupported. If the object ipsecSecurityProtocol has the value for IPcomp, then the ipsecSPI object is the CPI of the packet. Implementations SHOULD send one trap per peer (within a reasonable time period), rather than sending one trap per packet.
NTF bsnIpsecIkeNegFailure	1.3.6.1.4.1.14179.2.6.3.33			An attempt to negotiate a phase 1 IKE SA failed. The notification counts are also sent as part of the trap, along with the current value of the total negotiation error counters for ISAKMP.
NTF bsnIpsecSuiteNegFailure	1.3.6.1.4.1.14179.2.6.3.34			An attempt to negotiate a phase 2 SA suite for the specified selector failed. The current total failure counts are passed as well as the notification type counts for the notify involved in the failure.
NTF bsnIpsecInvalidCookieTrap	1.3.6.1.4.1.14179.2.6.3.35			ISAKMP packets with invalid cookies were detected from the specified source, intended for the specified destination. The initiator and responder cookies are also sent with the trap. The current count is sent to allow the trap to accurately relfect dropped and throttled traps. Implementations SHOULD send one trap per peer (within a reasonable time period, rather than sending one trap per packet.
NTF bsnRogueAPDetected	1.3.6.1.4.1.14179.2.6.3.36			When a Rogue AP is detected this Trap will be sent out along with APMacAddress on which its detected
NTF bsnAPLoadProfileUpdatedToPass	1.3.6.1.4.1.14179.2.6.3.37			When LOAD Profile state changes from FAIL to PASSt this notification will be sent with Dot3 MAC address of Airespace AP and slot ID of Airespace AP IF. This trap sending can be enable/disable using bsnRrmProfileTrapControlFlag
NTF bsnAPNoiseProfileUpdatedToPass	1.3.6.1.4.1.14179.2.6.3.38			When Noise Profile state changes from FAIL tp PASS, notification will be sent with Dot3 MAC address of Airespace AP and slot ID of Airespace AP IF. This trap sending can be enable/disable using bsnRrmProfileTrapControlFlag
NTF bsnAPInterferenceProfileUpdatedToPass	1.3.6.1.4.1.14179.2.6.3.39			When Interference Profile state changes from FAIL tp PASS, notification will be sent with Dot3 MAC address of Airespace AP and slot ID of Airespace AP IF. This trap sending can be enable /disable using bsnRrmProfileTrapControlFlag
NTF bsnAPCoverageProfileUpdatedToPass	1.3.6.1.4.1.14179.2.6.3.40			When Coverage Profile state changes from FAIL tp PASS, notification will be sent with Dot3 MAC address of Airespace AP and slot ID of Airespace AP IF. This trap sending can be enable/disable using bsnRrmProfileTrapControlFlag
NTF bsnRogueAPRemoved	1.3.6.1.4.1.14179.2.6.3.41			When a Rogue AP that was detected earlier no longer exists this Trap will be sent out along with APMacAddress on which its detected
NTF bsnRadiosExceedLicenseCount	1.3.6.1.4.1.14179.2.6.3.42			Whenever the currently associated Radios exceed the License Count This trap will be sent to annoy the Customer
NTF bsnSensedTemperatureTooHigh	1.3.6.1.4.1.14179.2.6.3.43			Temperature sensor temp too High - temp is too high on the unit. Immediate action should be taken
NTF bsnSensedTemperatureTooLow	1.3.6.1.4.1.14179.2.6.3.44			Temperature sensor temp too Low - temp is too high on the unit. Immediate action should be taken
NTF bsnTemperatureSensorFailure	1.3.6.1.4.1.14179.2.6.3.45			Temperature sensor hw failure - temp sensor has failed. Temperature is unknown
NTF bsnTemperatureSensorClear	1.3.6.1.4.1.14179.2.6.3.46			Temperature sensor clear -- temp sensor alarm condition is over. sensor is operating within proper temp range
NTF bsnPOEControllerFailure	1.3.6.1.4.1.14179.2.6.3.47			POE Controller has failed. Its a very critical trap. User intervention is required.
NTF bsnMaxRogueCountExceeded	1.3.6.1.4.1.14179.2.6.3.48			The number of rogues has exceeded the maximum Rogues allowed
NTF bsnMaxRogueCountClear	1.3.6.1.4.1.14179.2.6.3.49			The number of rogues is within the maximum Rogues allowed
NTF bsnApMaxRogueCountExceeded	1.3.6.1.4.1.14179.2.6.3.50			The number of rogues has exceeded the maximum Rogues allowed on the AP
NTF bsnApMaxRogueCountClear	1.3.6.1.4.1.14179.2.6.3.51			The number of rogues is within the maximum Rogues allowed on the AP
NTF bsnDot11StationBlacklisted	1.3.6.1.4.1.14179.2.6.3.52			The station blacklisted notification shall be sent when the client is blacklisted. The reason could be repeated auth or association failures or IP Address theft. The value of the notification shall include the MAC address of the MAC to which the Authentication frame was sent, the MAC and Slot Id of AP that client was associated to and the reason for black listing.
NTF bsnDot11StationAssociate	1.3.6.1.4.1.14179.2.6.3.53			The associate notification shall be sent when any of the watchlisted clients(present on at least one watch list) associates with an AP. The value of the notification shall include the MAC address and the Slot ID of the radio to which the station Associated.
NTF bsnApBigNavDosAttack	1.3.6.1.4.1.14179.2.6.3.55			The AP sent a string of messages with large NAV field. This is most likely a malicious denial of service attack.
NTF bsnTooManyUnsuccessLoginAttempts	1.3.6.1.4.1.14179.2.6.3.56			The Management User made too many unsuccessful login attempts.
NTF bsnWepKeyDecryptError	1.3.6.1.4.1.14179.2.6.3.57			Issued when a decrypt error occurrs. The WEP Key configured at the station may be wrong.
NTF bsnWpaMicErrorCounterActivated	1.3.6.1.4.1.14179.2.6.3.58			Issued when a WPA MIC error occurs and a counter measure is activated at the AP.
NTF bsnRogueAPDetectedOnWiredNetwork	1.3.6.1.4.1.14179.2.6.3.59			When a Rogue is detected on the wired network this trap will be sent out. The same trap with bsnRogueAPOnWiredNetwork set to no will clear the previous trap.
NTF bsnApHasNoRadioCards	1.3.6.1.4.1.14179.2.6.3.60			When an AP has no radio cards present on it, the switch sends this trap.
NTF bsnDuplicateIpAddressReported	1.3.6.1.4.1.14179.2.6.3.61			This trap is issued when the switch or an AP detects another machine using its IP Address. The first variable has value yes if the duplicate IP is reported by an AP. In that case, the second attribute will carry the AP MAC Address. The third variable is the duplicate IP address in question and the last attribute is the MAC Address of the machine that is found to be using the duplicate IP.
NTF bsnAPContainedAsARogue	1.3.6.1.4.1.14179.2.6.3.62			When our AP detects that it is being contained by another AP, this trap is issued. The clear flag is true if the AP is no longer being contained.
NTF bsnTrustedApHasInvalidSsid	1.3.6.1.4.1.14179.2.6.3.63			Issued when a Trusted Rogue AP is auto contained for advertising invalid SSID. If the clear variable has value true, then the trap clears the earlier alert.
NTF bsnTrustedApIsMissing	1.3.6.1.4.1.14179.2.6.3.64			Issued when a Trusted Rogue AP is missing or has failed. If the clear variable has value true, then the trap clears the earlier alert.
NTF bsnAdhocRogueAutoContained	1.3.6.1.4.1.14179.2.6.3.65			Issued when an Adhoc Rogue is auto contained. If the clear variable has value true, then the trap clears the earlier alert.
NTF bsnRogueApAutoContained	1.3.6.1.4.1.14179.2.6.3.66			Issued when a Rogue AP is auto contained for advertising our SSID. If the clear variable has value true, then the trap clears the earlier alert.
NTF bsnTrustedApHasInvalidEncryption	1.3.6.1.4.1.14179.2.6.3.67			Issued when a Trusted Rogue AP is auto contained for using invalid encryption. The second param is for the encryption used and the third param is for encryption required. If the clear variable has value true, then the trap clears the earlier alert.
NTF bsnTrustedApHasInvalidRadioPolicy	1.3.6.1.4.1.14179.2.6.3.68			Issued when a Trusted Rogue AP is auto contained for using invalid radio policy. The second param is for the radio policy used and the third param is for radio policy required. If the clear variable has value true, then the trap clears the earlier alert.
NTF bsnNetworkStateChanged	1.3.6.1.4.1.14179.2.6.3.69			When the 802.11a or b/g network state is changed this trap is issued.
NTF bsnSignatureAttackDetected	1.3.6.1.4.1.14179.2.6.3.70			This trap is sent out when a signature attack is detected by the switch. The standard and custom signatures are predefined on the switch (see bsnSignatureConfig group). The signatures also defines if its detection should be reported. The trap variables bsnSignatureName and bsnSignatureDescription are retrieved from the detected signature definition. Clear Trap Variable is turned on when the signature attack stops. The signature's quiet time configuration speicifes the time after which the clear trap would be sent. bsnSignatureMacInfo indicates whether the signature is used to track pattern matches for all source MAC addresses together or seperately for individual source MAC addresses. bsnSignatureAttackFrequency will carry the value for a specific MAC address or for all MAC addresses depending on bsnSignatureMacInfo.
NTF bsnAPRadioCardTxFailure	1.3.6.1.4.1.14179.2.6.3.71			This trap is sent by the switch when a radio card on an AP stops transmitting.
NTF bsnAPRadioCardTxFailureClear	1.3.6.1.4.1.14179.2.6.3.72			This trap is sent by the switch when a radio card on an AP starts transmitting again after a prior failure.
NTF bsnAPRadioCardRxFailure	1.3.6.1.4.1.14179.2.6.3.73			This trap is sent by the switch when a radio card on an AP stops receiving.
NTF bsnAPRadioCardRxFailureClear	1.3.6.1.4.1.14179.2.6.3.74			This trap is sent by the switch when a radio card on an AP starts receiving again after a prior failure.
NTF bsnAPImpersonationDetected	1.3.6.1.4.1.14179.2.6.3.75			This trap is sent by the switch when a radio of an authenticated AP hears from another AP whose MAC Address neither matches that of a rogue's and nor is it an authenticated neighbor of the detecting AP.
NTF bsnTrustedApHasInvalidPreamble	1.3.6.1.4.1.14179.2.6.3.76			Issued when a Trusted Rogue AP is auto contained for using invalid preamble. The second param is for the preamble used and the third param is for preamble required. If the clear variable has value true, then the trap clears the earlier alert.
NTF bsnAPIPAddressFallback	1.3.6.1.4.1.14179.2.6.3.77			This trap is sent out when an AP, with the configured static ip-address, fails to establish connection with outside world and starts using DHCP as a fallback option.
NTF bsnAPFunctionalityDisabled	1.3.6.1.4.1.14179.2.6.3.78			This trap is sent out when AP functionality on the switch is disabled because the License key has expired or has been deleted or doesn't match the switch image.
NTF bsnAPRegulatoryDomainMismatch	1.3.6.1.4.1.14179.2.6.3.79			This trap is generated if an AP's regulatory domain doesn't match the country the switch is configured for. Due to the mismatch, the AP will fail to associate with the Switch.
NTF bsnRxMulticastQueueFull	1.3.6.1.4.1.14179.2.6.3.80			This trap indicates that the CPU's Receive Multicast Queue is Full.
NTF bsnRadarChannelDetected	1.3.6.1.4.1.14179.2.6.3.81			This trap is sent when radar signals are detected on the current channel
NTF bsnRadarChannelCleared	1.3.6.1.4.1.14179.2.6.3.82			This trap will be generated, if a radar trap has been generated earlier, after the expiry of Non-Occupancy Period.
NTF bsnAPAuthorizationFailure	1.3.6.1.4.1.14179.2.6.3.83			This trap is sent out in case of authorization failure while attempting to associate the AP to the controller. bsnAPDot3MacAddress represents the mac-address of that AP. bsnAPName is name of AP
NTF radioCoreDumpTrap	1.3.6.1.4.1.14179.2.6.3.84			When radio module in AP dumps core, it informs controller and controller generates this trap. The core file can be retrieved on demand.
NTF invalidRadioTrap	1.3.6.1.4.1.14179.2.6.3.85			This trap will be generated when an AP has joined is using unsupported radio or a radio slot not currently not being used.
NTF countryChangeTrap	1.3.6.1.4.1.14179.2.6.3.86			This trap will be generated when an operator changes the country of operation. New country code will be sent in trap.
NTF unsupportedAPTrap	1.3.6.1.4.1.14179.2.6.3.87			This trap will be generated when unsupported AP try to join 40xx/410x or 3500 with 64MB flash.
NTF heartbeatLossTrap	1.3.6.1.4.1.14179.2.6.3.88			This trap will be generated when controller loses connection with the Supervisor Switch in which it is physically embedded and doesn't hear the heartbeat keepalives from the Supervisor.
NTF locationNotifyTrap	1.3.6.1.4.1.14179.2.6.3.89			This trap will be generated by the location server for notifications of location events.
bsnUtility	1.3.6.1.4.1.14179.2.7
bsnSyslog	1.3.6.1.4.1.14179.2.7.1
INT bsnSyslogEnable	1.3.6.1.4.1.14179.2.7.1.1	INTEGER	read-write
STR bsnSyslogRemoteAddress	1.3.6.1.4.1.14179.2.7.1.2	DisplayString	read-write	This would be the IP Address or host name
bsnPing	1.3.6.1.4.1.14179.2.7.2
bsnPingTestTable	1.3.6.1.4.1.14179.2.7.2.1		not-accessible	PingTest Table
bsnPingTestEntry	1.3.6.1.4.1.14179.2.7.2.1.1		not-accessible	An Entry (conceptual row) in the bsnPingTest Table.
I32 bsnPingTestId	1.3.6.1.4.1.14179.2.7.2.1.1.1	Integer32	read-create	Test ID
IP bsnPingTestIPAddress	1.3.6.1.4.1.14179.2.7.2.1.1.2	IpAddress	read-create	Ip Address to ping
I32 bsnPingTestSendCount	1.3.6.1.4.1.14179.2.7.2.1.1.3	Integer32	read-create	Number of bytes sent
I32 bsnPingTestReceivedCount	1.3.6.1.4.1.14179.2.7.2.1.1.4	Integer32	read-only	Number of bytes received.
INT bsnPingTestStatus	1.3.6.1.4.1.14179.2.7.2.1.1.5	INTEGER	read-only	Status of the ping test
U32 bsnPingTestMaxTimeInterval	1.3.6.1.4.1.14179.2.7.2.1.1.6	Unsigned32	read-only	Maximum time interval in msec.
U32 bsnPingTestMinTimeInterval	1.3.6.1.4.1.14179.2.7.2.1.1.7	Unsigned32	read-only	Minimum time interval in msec.
U32 bsnPingTestAvgTimeInterval	1.3.6.1.4.1.14179.2.7.2.1.1.8	Unsigned32	read-only	Average time interval in msec.
ROW bsnPingTestRowStatus	1.3.6.1.4.1.14179.2.7.2.1.1.25	RowStatus	read-create	Row Status
bsnLinkTest	1.3.6.1.4.1.14179.2.7.3
bsnLinkTestTable	1.3.6.1.4.1.14179.2.7.3.1		not-accessible	LinkTest Table
bsnLinkTestEntry	1.3.6.1.4.1.14179.2.7.3.1.1		not-accessible	An Entry (conceptual row) in the bsnLinkTest Table.
I32 bsnLinkTestId	1.3.6.1.4.1.14179.2.7.3.1.1.1	Integer32	read-create	Link Test ID
MAC bsnLinkTestMacAddress	1.3.6.1.4.1.14179.2.7.3.1.1.2	MacAddress	read-create	MAC Address of link to test
I32 bsnLinkTestSendPktCount	1.3.6.1.4.1.14179.2.7.3.1.1.3	Integer32	read-create	Number of packets sent.
I32 bsnLinkTestSendPktLength	1.3.6.1.4.1.14179.2.7.3.1.1.4	Integer32	read-create	Length of sent packet
I32 bsnLinkTestReceivedPktCount	1.3.6.1.4.1.14179.2.7.3.1.1.5	Integer32	read-only	Number of received packets.
I32 bsnLinkTestClientRSSI	1.3.6.1.4.1.14179.2.7.3.1.1.6	Integer32	read-only	Client RSSI value of link.
I32 bsnLinkTestLocalSNR	1.3.6.1.4.1.14179.2.7.3.1.1.7	Integer32	read-only	Local SNR of the link
I32 bsnLinkTestLocalRSSI	1.3.6.1.4.1.14179.2.7.3.1.1.8	Integer32	read-only	Local RSSI of the link.
INT bsnLinkTestStatus	1.3.6.1.4.1.14179.2.7.3.1.1.9	INTEGER	read-only	Status of the link test.
ROW bsnLinkTestRowStatus	1.3.6.1.4.1.14179.2.7.3.1.1.30	RowStatus	read-create	Row Status
bsnMobility	1.3.6.1.4.1.14179.2.8
bsnMobilityConfig	1.3.6.1.4.1.14179.2.8.1
I32 bsnMobilityProtocolPortNum	1.3.6.1.4.1.14179.2.8.1.1	Integer32	read-write	Port Number on which mobility Protocol runs
INT bsnMobilityDynamicDiscovery	1.3.6.1.4.1.14179.2.8.1.3	INTEGER	read-write	Statically Configured is always enabled if members are defined. To further enable rrm discovery, learned discovery, broadcast discovery, enable/disable this attribute.
INT bsnMobilityStatsReset	1.3.6.1.4.1.14179.2.8.1.4	INTEGER	read-write	Reset mobility statistics by setting this atribute to resetNow. If you try to read this attribute value will always be 0.
bsnMobilityGroupMembersTable	1.3.6.1.4.1.14179.2.8.1.10		not-accessible	MWAR List (statically configured members of the mobility group)
bsnMobilityGroupMembersEntry	1.3.6.1.4.1.14179.2.8.1.10.1		not-accessible	An Entry (conceptual row) in the bsnMobilityGroupMembers Table.
MAC bsnMobilityGroupMemberMacAddress	1.3.6.1.4.1.14179.2.8.1.10.1.1	MacAddress	read-create	Member switch MAC Address
IP bsnMobilityGroupMemberIPAddress	1.3.6.1.4.1.14179.2.8.1.10.1.2	IpAddress	read-create	Member switch IP Address
STR bsnMobilityGroupMemberGroupName	1.3.6.1.4.1.14179.2.8.1.10.1.3	DisplayString	read-create	Member's group name. If left empty while adding a new group member, this assumes the default mobility group name of the switch.
ROW bsnMobilityGroupMemberRowStatus	1.3.6.1.4.1.14179.2.8.1.10.1.22	RowStatus	read-create	Row Status
bsnMobilityAnchorsTable	1.3.6.1.4.1.14179.2.8.1.11		not-accessible	Statically configured mobility anchors
bsnMobilityAnchorsEntry	1.3.6.1.4.1.14179.2.8.1.11.1		not-accessible	An Entry (conceptual row) in the bsnMobilityAnchorsTable Table.
STR bsnMobilityAnchorWlanSsid	1.3.6.1.4.1.14179.2.8.1.11.1.1	DisplayString	read-create	Local wlan-ssid to connect to Guest/Anchor switch
IP bsnMobilityAnchorSwitchIPAddress	1.3.6.1.4.1.14179.2.8.1.11.1.2	IpAddress	read-create	Guest/Anchor switch IP Address
ROW bsnMobilityAnchorRowStatus	1.3.6.1.4.1.14179.2.8.1.11.1.20	RowStatus	read-create	Row Status
bsnMobilityStats	1.3.6.1.4.1.14179.2.8.2
C32 bsnTotalHandoffRequestsEx	1.3.6.1.4.1.14179.2.8.2.1	Counter32	read-only	Total handoff requests
C32 bsnTotalHandoffs	1.3.6.1.4.1.14179.2.8.2.2	Counter32	read-only	Total handoffs
C32 bsnCurrentExportedClients	1.3.6.1.4.1.14179.2.8.2.3	Counter32	read-only	Current exported client count
C32 bsnTotalExportedClients	1.3.6.1.4.1.14179.2.8.2.4	Counter32	read-only	Total exported client count
C32 bsnCurrentImportedClients	1.3.6.1.4.1.14179.2.8.2.5	Counter32	read-only	Current Imported client count
C32 bsnTotalImportedClients	1.3.6.1.4.1.14179.2.8.2.6	Counter32	read-only	Total Imported client count
C32 bsnTotalHandoffErrors	1.3.6.1.4.1.14179.2.8.2.7	Counter32	read-only	Total handoff errors
C32 bsnTotalCommunicationErrors	1.3.6.1.4.1.14179.2.8.2.8	Counter32	read-only	Total communication errors
bsnMobilityGroupDirectoryTable	1.3.6.1.4.1.14179.2.8.2.9		not-accessible	MWAR List (statically configured members of the mobility group)
bsnMobilityGroupDirectoryEntry	1.3.6.1.4.1.14179.2.8.2.9.1		not-accessible	An Entry (conceptual row) in the bsnMobilityGroupDirectory Table.
IP bsnGroupDirectoryMemberIPAddress	1.3.6.1.4.1.14179.2.8.2.9.1.1	IpAddress	read-only	Mwar Ip Address
MAC bsnGroupDirectoryMemberMacAddress	1.3.6.1.4.1.14179.2.8.2.9.1.2	MacAddress	read-only	Mwar Mac Address
INT bsnGroupDirectoryDicoveryType	1.3.6.1.4.1.14179.2.8.2.9.1.3	INTEGER	read-only	Discovery type of the Group Directory.
C32 bsnMemberCurrentAnchoredClients	1.3.6.1.4.1.14179.2.8.2.9.1.4	Counter32	read-only	Current anchored client count
C32 bsnMemberTotalAnchoredClients	1.3.6.1.4.1.14179.2.8.2.9.1.5	Counter32	read-only	Total anchored client count
C32 bsnMemberCurrentExportedClients	1.3.6.1.4.1.14179.2.8.2.9.1.6	Counter32	read-only	Current exported client count
C32 bsnMemberTotalExportedClients	1.3.6.1.4.1.14179.2.8.2.9.1.7	Counter32	read-only	Total exported client count
C32 bsnMemberCurrentImportedClients	1.3.6.1.4.1.14179.2.8.2.9.1.8	Counter32	read-only	Current Imported client count
C32 bsnMemberTotalImportedClients	1.3.6.1.4.1.14179.2.8.2.9.1.9	Counter32	read-only	Total Imported client count
C32 bsnMemberTotalHandoffErrors	1.3.6.1.4.1.14179.2.8.2.9.1.10	Counter32	read-only	Total handoff errors
C32 bsnMemberTotalCommunicationErrors	1.3.6.1.4.1.14179.2.8.2.9.1.30	Counter32	read-only	Total Communication errors
C32 bsnTotalReceiveErrors	1.3.6.1.4.1.14179.2.8.2.10	Counter32	read-only	Total receive errors
C32 bsnTotalTransmitErrors	1.3.6.1.4.1.14179.2.8.2.11	Counter32	read-only	Total Transmit errors
C32 bsnTotalResponsesRetransmitted	1.3.6.1.4.1.14179.2.8.2.12	Counter32	read-only	Total Responses Retransmitted
C32 bsnTotalHandoffEndRequestsReceived	1.3.6.1.4.1.14179.2.8.2.13	Counter32	read-only	Total Handoff End Requests Received
C32 bsnTotalStateTransitionsDisallowed	1.3.6.1.4.1.14179.2.8.2.14	Counter32	read-only	Total State Transitions Disallowed
C32 bsnTotalResourceErrors	1.3.6.1.4.1.14179.2.8.2.15	Counter32	read-only	Total Resource Errors
C32 bsnTotalHandoffRequestsSent	1.3.6.1.4.1.14179.2.8.2.16	Counter32	read-only	Total Handoff Requests Sent
C32 bsnTotalHandoffRepliesReceived	1.3.6.1.4.1.14179.2.8.2.17	Counter32	read-only	Total Handoff Replies Received
C32 bsnTotalHandoffAsLocalReceived	1.3.6.1.4.1.14179.2.8.2.18	Counter32	read-only	Total Handoffs As Local Received
C32 bsnTotalHandoffAsForeignReceived	1.3.6.1.4.1.14179.2.8.2.19	Counter32	read-only	Total Handoffs As Foreign Received
C32 bsnTotalHandoffDeniesReceived	1.3.6.1.4.1.14179.2.8.2.20	Counter32	read-only	Total Handoff Denies Received
C32 bsnTotalAnchorRequestsSent	1.3.6.1.4.1.14179.2.8.2.21	Counter32	read-only	Total Anchor Requests Sent
C32 bsnTotalAnchorDenyReceived	1.3.6.1.4.1.14179.2.8.2.22	Counter32	read-only	Total Anchor Deny Received
C32 bsnTotalAnchorGrantReceived	1.3.6.1.4.1.14179.2.8.2.23	Counter32	read-only	Total Anchor Grant Received
C32 bsnTotalAnchorTransferReceived	1.3.6.1.4.1.14179.2.8.2.24	Counter32	read-only	Total Anchor Transfer Received
C32 bsnTotalHandoffRequestsIgnored	1.3.6.1.4.1.14179.2.8.2.25	Counter32	read-only	Total Handoff Requests Ignored
C32 bsnTotalPingPongHandoffRequestsDropped	1.3.6.1.4.1.14179.2.8.2.26	Counter32	read-only	Total Ping Pong Handoff Requests Dropped
C32 bsnTotalHandoffRequestsDropped	1.3.6.1.4.1.14179.2.8.2.27	Counter32	read-only	Total Handoff Requests Dropped
C32 bsnTotalHandoffRequestsDenied	1.3.6.1.4.1.14179.2.8.2.28	Counter32	read-only	Total Handoff Requests Denied
C32 bsnTotalClientHandoffAsLocal	1.3.6.1.4.1.14179.2.8.2.29	Counter32	read-only	Total Client Handoffs As Local
C32 bsnTotalClientHandoffAsForeign	1.3.6.1.4.1.14179.2.8.2.30	Counter32	read-only	Total Client Handoffs As Foreign
C32 bsnTotalAnchorRequestsReceived	1.3.6.1.4.1.14179.2.8.2.31	Counter32	read-only	Total Anchor Requests Received
C32 bsnTotalAnchorRequestsDenied	1.3.6.1.4.1.14179.2.8.2.32	Counter32	read-only	Total Anchor Requests Denied
C32 bsnTotalAnchorRequestsGranted	1.3.6.1.4.1.14179.2.8.2.33	Counter32	read-only	Total Anchor Requests Granted
C32 bsnTotalAnchorTransferred	1.3.6.1.4.1.14179.2.8.2.34	Counter32	read-only	Total Anchor Transferred
C32 bsnTotalHandoffRequestsReceived	1.3.6.1.4.1.14179.2.8.2.35	Counter32	read-only	Total Handoff Requests Received
bsnIpsec	1.3.6.1.4.1.14179.2.9
OCT bsnWrasIpsecCACertificate	1.3.6.1.4.1.14179.2.9.1	OCTET STRING	read-only
OCT bsnWrasIpsecCACertificateUpdate	1.3.6.1.4.1.14179.2.9.2	OCTET STRING	read-write	Note this attribute is for updating the certificate If you try to read it, it will always be ***
bsnWrasIpsecCertTable	1.3.6.1.4.1.14179.2.9.3		not-accessible	A table of Certificates.
bsnWrasIpsecCertEntry	1.3.6.1.4.1.14179.2.9.3.1		not-accessible	Each entry contains a specific certificate.
STR bsnWrasIpsecCertName	1.3.6.1.4.1.14179.2.9.3.1.1	DisplayString	read-create	The name assigned to this set of IKE Certificates.
OCT bsnWrasIpsecCertificateUpdate	1.3.6.1.4.1.14179.2.9.3.1.2	OCTET STRING	read-create	If you try to read this it will always be ***
OCT bsnWrasIpsecCertificate	1.3.6.1.4.1.14179.2.9.3.1.3	OCTET STRING	read-only
OCT bsnWrasIpsecCertPassword	1.3.6.1.4.1.14179.2.9.3.1.4	OCTET STRING	read-create
ROW bsnWrasIpsecCertStatus	1.3.6.1.4.1.14179.2.9.3.1.24	RowStatus	read-create	A row status type for the IKE Cert Entry.
bsnAPGroupsVlanConfig	1.3.6.1.4.1.14179.2.10
INT bsnAPGroupsVlanFeature	1.3.6.1.4.1.14179.2.10.1	INTEGER	read-write	When enabled, Site Specific WLAN feature is enforced.
bsnAPGroupsVlanTable	1.3.6.1.4.1.14179.2.10.2		not-accessible	Wireless Sites Table.
bsnAPGroupsVlanEntry	1.3.6.1.4.1.14179.2.10.2.1		not-accessible	An entry in bsnAPGroupsVlanTable.
OCT bsnAPGroupsVlanName	1.3.6.1.4.1.14179.2.10.2.1.1	OCTET STRING	read-create	The string is an unique identifier/name assigned to a site.
OCT bsnAPGroupsVlanDescription	1.3.6.1.4.1.14179.2.10.2.1.2	OCTET STRING	read-create	Description about the site.
ROW bsnAPGroupsVlanRowStatus	1.3.6.1.4.1.14179.2.10.2.1.20	RowStatus	read-create	Row Status for creation/deletion of entries in bsnAPGroupsVlanTable
bsnAPGroupsVlanMappingTable	1.3.6.1.4.1.14179.2.10.3		not-accessible	A table for the WLAN-interace-mappings allowed for each configured site. Each site can have a set of WLANs associated with it.
bsnAPGroupsVlanMappingEntry	1.3.6.1.4.1.14179.2.10.3.1		not-accessible	An entry in bsnAPGroupsVlanMappingTable.
STR bsnAPGroupsVlanMappingSsid	1.3.6.1.4.1.14179.2.10.3.1.1	DisplayString	read-create	When an AP is associated with a site, and the site has an associated set of WLANs, then only those WLANs are beamed by the AP. Here 'bsnAPGroupsVlanMappingSsid' is the wlan to be used when a client connects on this AP.
OCT bsnAPGroupsVlanMappingInterfaceName	1.3.6.1.4.1.14179.2.10.3.1.2	OCTET STRING	read-create	When an AP is associated with a site, and the site has an associated set of WLANs, then only those WLANs are beamed by the AP. Here 'bsnAPGroupsVlanMappingInterfaceName' is the interface to be used when a client connects to the 'bsnAPGroupsVlanMappingSsid' WLAN on this AP.
ROW bsnAPGroupsVlanMappingRowStatus	1.3.6.1.4.1.14179.2.10.3.1.20	RowStatus	read-create	Row Status for creation/deletion of WLAN-interface-mappings asscoiated with sites.
bsnWrasGroups	1.3.6.1.4.1.14179.2.50
bsnEssGroup	1.3.6.1.4.1.14179.2.50.1			This collection of objects provides information about Airespace Wireless LAN Configuration Attributes These objects are defined under bsnEss object.
bsnApGroup	1.3.6.1.4.1.14179.2.50.2			This collection of objects provide the information about Airespace APs that are associated with the Switch. These objects are defined under bsnAP object.
bsnGlobalDot11Group	1.3.6.1.4.1.14179.2.50.3			This collection of objects provide the information about Airespace 802.11 standard attributes applied globally. These objects are defined under bsnGlobalDot11 object.
bsnRrmGroup	1.3.6.1.4.1.14179.2.50.4			This collection of objects provide the information about Airespace Radio Resource Management Configuration Parameters. These objects are defined under bsnRrm object.
bsnAAAGroup	1.3.6.1.4.1.14179.2.50.5			This collection of objects provide the information about Airespace Authentication, Authorization, and Accounting Attributes. These objects are defined under bsnAAA object.
bsnTrapsGroup	1.3.6.1.4.1.14179.2.50.6			This collection of objects provide the information about Airespace Trap Configuration and Trap definition. These objects are defined under bsnTrap.
bsnUtilityGroup	1.3.6.1.4.1.14179.2.50.7			This collection of objects provide the information about Airespace General Utilities such as ping, syslog. These objects are defined under bsnUtility.
bsnMobilityGroup	1.3.6.1.4.1.14179.2.50.8			This collection of objects provide the information about Airespace Mobility Group Parameters and ststistics. These are objects defined under bsnMobility.
bsnIpsecGroup	1.3.6.1.4.1.14179.2.50.9			This collection of objects provide the information about Airespace Global IpSec Group. These objects are defined under bsnIpsec.
bsnWrasDepGroup	1.3.6.1.4.1.14179.2.50.10			This collection of objects are derprecated in bsnWireless module.
bsnWrasObsGroup	1.3.6.1.4.1.14179.2.50.11			This collection of objects are obsoleted in bsnWireless module.
bsnWrasTrap	1.3.6.1.4.1.14179.2.50.12			This collection of objects provides all notification that Switch need to generate to the Management System.
bsnEssGroupRev1	1.3.6.1.4.1.14179.2.50.13			This collection of objects provides information about Airespace Wireless LAN Configuration Attributes These objects are defined under bsnEss object.
bsnGlobalDot11GroupRev1	1.3.6.1.4.1.14179.2.50.14			This collection of objects provide the information about Airespace 802.11 standard attributes applied globally. These objects are defined under bsnGlobalDot11 object.
bsnAAAGroupRev1	1.3.6.1.4.1.14179.2.50.15			This collection of objects provide the information about Airespace Authentication, Authorization, and Accounting Attributes. These objects are defined under bsnAAA object.
bsnTrapsGroupRev1	1.3.6.1.4.1.14179.2.50.16			This collection of objects provide the information about Airespace Trap Configuration and Trap definition. These objects are defined under bsnTrap.
bsnWrasTrapRev1	1.3.6.1.4.1.14179.2.50.17			This collection of objects provides all notification that Switch need to generate to the Management System.
bsnApGroupRev1	1.3.6.1.4.1.14179.2.50.18			This collection of objects provide the information about Airespace APs that are associated with the Switch. These objects are defined under bsnAP object.
bsnUtilityGroupRev1	1.3.6.1.4.1.14179.2.50.19			This collection of objects provide the information about Airespace General Utilities such as ping, syslog. These objects are defined under bsnUtility.
bsnWrasObsGroupRev1	1.3.6.1.4.1.14179.2.50.20			This collection of objects are obsoleted in bsnWireless module.
bsnWrasObsTrap	1.3.6.1.4.1.14179.2.50.21			This collection of objects provides all notification that Switch need to generate to the Management System.
bsnWrasCompliances	1.3.6.1.4.1.14179.2.51
bsnWrasCompliance	1.3.6.1.4.1.14179.2.51.1			The compliance statement for the SNMP entities that implement the bsnWireless module.
bsnWrasComplianceRev1	1.3.6.1.4.1.14179.2.51.2			The compliance statement for the SNMP entities that implement the bsnWireless module.

RFC description

Management of Airespace wireless controllers (LWAPP) for 802.11 access points, AAA, mobility, and QoS.

Start monitoring Cisco (Airespace) Wireless LAN Controllers (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download AIRESPACE-WIRELESS-MIB