Wellfleet-OSPF-MIB

All MIBs › Wellfleet-OSPF-MIB

Category: Wellfleet BayNetworks Routing Protocols

Description: Manages Wellfleet OSPF area configurations, neighbor adjacencies, LSA database, and route calculation statistics.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Wellfleet-OSPF-MIB?

Wellfleet-OSPF-MIB is a legacy vendor MIB from Wellfleet Communications (a router vendor later absorbed into Bay Networks/Nortel) for managing the OSPF interior gateway routing protocol on Wellfleet routers. It exposes OSPF area configuration, neighbor adjacency state, link-state advertisement (LSA) database contents, and route calculation statistics. Rather than hardware health, this MIB focuses on monitoring routing-protocol software status -- specifically OSPF neighbor adjacency state, LSA database size and age, and SPF recalculation counts -- which reveal routing instability or slow convergence. It closely parallels the later industry-standard OSPF-MIB (RFC 1253/1850), reflecting Wellfleet's proprietary OSPF implementation from before standardized MIBs were widely adopted. It was deployed on Wellfleet/Bay Networks routers in enterprise and service-provider backbone networks running OSPF, where Wellfleet-OSPF-MIB SNMP monitoring helped confirm neighbor adjacencies remained stable and converged.

IPNetwork Monitor allows you to monitor SNMP objects defined in Wellfleet-OSPF-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Wellfleet/Bay Networks routers

Monitoring Examples

No object names were available for this module, but a realistic scenario would involve polling OSPF neighbor adjacency and area tables to confirm all expected neighbors remain in the full adjacency state; a neighbor dropping out of full state, or a spike in SPF recalculations, would indicate topology instability or a flapping link that needs investigation.

What Can Be Monitored

OSPF neighbor adjacency state
OSPF area configuration
LSA database contents
SPF route recalculation statistics

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter
Gauge
IpAddress

From RFC1213-MIB

DisplayString

From Wellfleet-COMMON-MIB

wfOspfGroup

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
wfOspfGeneralGroup	1.3.6.1.4.1.18.3.5.3.2.3.1
INT wfOspfGeneralDelete	1.3.6.1.4.1.18.3.5.3.2.3.1.1	INTEGER	read-write	'This value determines whether OSPF is configured'
INT wfOspfGeneralDisable	1.3.6.1.4.1.18.3.5.3.2.3.1.2	INTEGER	read-write	'The administrative status of OSPF in the router. The value 'enabled' denotes that the OSPF Process is active on at least one interface; 'disabled' disables it on all interfaces.'
INT wfOspfGeneralState	1.3.6.1.4.1.18.3.5.3.2.3.1.3	INTEGER	read-only	'The state of OSPF'
IP wfOspfRouterId	1.3.6.1.4.1.18.3.5.3.2.3.1.4	IpAddress	read-write	'A 32-bit integer uniquely identifying the router in the Autonomous System. By convention, to ensure uniqueness, this should default to the value of one of the router's IP interface addresses.' REFERENCE 'OSPF Version 2, C.1 Global parameters'
INT wfOspfVersionNumber	1.3.6.1.4.1.18.3.5.3.2.3.1.5	INTEGER	read-only	'The current version number of the OSPF protocol is 2.' REFERENCE 'OSPF Version 2, Title'
INT wfOspfAreaBdrRtrStatus	1.3.6.1.4.1.18.3.5.3.2.3.1.6	INTEGER	read-only	'A flag to note whether this router is an area border router.' REFERENCE 'OSPF Version 2, Section 3 Splitting the AS into Areas'
INT wfOspfASBdrRtrStatus	1.3.6.1.4.1.18.3.5.3.2.3.1.7	INTEGER	read-write	'A flag to note whether this router is an Autonomous System border router.' REFERENCE 'OSPF Version 2, Section 3.3 Classification of routers'
INT wfOspfTOSSupport	1.3.6.1.4.1.18.3.5.3.2.3.1.8	INTEGER	read-only	'The router's support for type-of-service routing.' REFERENCE 'OSPF Version 2, Appendix F.1.2 Optional TOS support'
INT wfOspfSpfHoldDown	1.3.6.1.4.1.18.3.5.3.2.3.1.9	INTEGER	read-write	Hold Down Timer for the SPF. The SPF will run at most once per hold down timer value. A value of 0 means no hold down.
GAU wfOspfSlotMask	1.3.6.1.4.1.18.3.5.3.2.3.1.10	Gauge	read-write	Slot mask for which slots OSPF is eligible to run on. The MSBit represents slot 1, the next most significant bit represents slot 2, and so on... Slots can be 1-14. Default is all slots on a BCN.
INT wfOspfNewAseMetricSupport	1.3.6.1.4.1.18.3.5.3.2.3.1.11	INTEGER	read-write	A parameter to specify if the new style ASE metric support is enabled. The new metric is not compatible with the pre-8.0 ASE metrics. The new metric support should be disabled if the router is to interoperate with routers running a pre-8.0 OSPF version.
INT wfOspfBackupDisable	1.3.6.1.4.1.18.3.5.3.2.3.1.12	INTEGER	read-only	This parameter enables or disables the backup OSPF soloist's backup link state database. When the parameter is set to disabled the OSPF backup soloist will not maintain a copy of the OSPF link state database.
GAU wfOspfPrimaryLogMask	1.3.6.1.4.1.18.3.5.3.2.3.1.13	Gauge	read-write	A parameter to specify which OSPF log messages should be logged. This will only effect the Primary OSPF gate. Each bit represents a message as defined below. A 1 in that bit location means to log it and a 0 means not to put that log message in the log. Changing this value will NOT restart OSPF, but will take effct immediately(if there are any messages to be logged. bit 31 bit 0 +---------------------------------------+ \| \| +---------------------------------------+ bit0 Trace Messages bit1 INFO Level messages bit2 debug level messages bit3 OSPF interface state change messages bit4 Nbr state changes bit5 self-origination of LSA's bit6 receipt of new LSA's bit7 changes to OSPF`s Routing Table bit8 Bad LS requests, Ack's, or updates bit9 receipt of less recent LSA's bit10 receipt of more recent self-originated LSA's bit11 receipt of MAxAge LSA's (i.e. LSA's being flushed) bit12 - 31 reserved
GAU wfOspfBackupLogMask	1.3.6.1.4.1.18.3.5.3.2.3.1.14	Gauge	read-only	A parameter to specify which OSPF log messages should be logged. This will only effect the Backup OSPF gate. Each bit represents a message as defined below. A 1 in that bit location means to log it a 0 means not to put that log message in the log. Changing this value will NOT restart OSPF, but will take effct immediately(if there are any messages to be logged. bit 31 bit 0 +---------------------------------------+ \| \| +---------------------------------------+ bit0 Trace Messages bit1 INFO Level messages bit2 debug level messages bit3 OSPF interface state change messages bit4 Nbr state changes bit5 self-origination of LSA's bit6 receipt of new LSA's bit7 changes to OSPF`s Routing Table bit8 Bad LS requests, Ack's, or updates bit9 receipt of less recent LSA's bit10 receipt of more recent self-originated LSA's bit11 receipt of MAxAge LSA's (i.e. LSA's being flushed) bit12 - 31 reserved
INT wfOspfAseTagDefault	1.3.6.1.4.1.18.3.5.3.2.3.1.15	INTEGER	read-write	This parameter indicates how ASE tags will be generated for those ASEs whose tags are not altered by an export route filter or announce route policy. default(1) indicates that a zero value is used. automatic(2) indicates that an automatic tag will be generated as specified in RFC 1403. proprietary(3) indicates that the wellfleet proprietary scheme will be used. In this case, the next hop is used for IGP routes and the neighbor AS is used for EGP routes.
INT wfOspfPrimarySlot	1.3.6.1.4.1.18.3.5.3.2.3.1.16	INTEGER	read-only	Slot on which OSPF Primary is running. Slots can be 1-14. Default is zero.
INT wfOspfBackupSlot	1.3.6.1.4.1.18.3.5.3.2.3.1.17	INTEGER	read-only	Slot on which OSPF Backup is running. Slots can be 1-14. Default is zero.
INT wfOspfMaximumPath	1.3.6.1.4.1.18.3.5.3.2.3.1.18	INTEGER	read-write	Maximum number of equal cost paths allowed for a network installed by OSPF.
STR wfOspfSlotPriority	1.3.6.1.4.1.18.3.5.3.2.3.1.19	DisplayString	read-write	Comma-separated list of slots specifying the order in which slots should attempt to bring up OSPF soloist. They are listed in the decreasing order of priority. Slot with priority 0, i.e. the first entry in the list, is most likely to have OSPF soloist running on it.
CTR wfOspfLsdbCount	1.3.6.1.4.1.18.3.5.3.2.3.1.20	Counter	read-only	Running count of LSDB entries
INT wfOspfMulticastExtensions	1.3.6.1.4.1.18.3.5.3.2.3.1.21	INTEGER	read-write	A Bit Mask indicating whether the router is forwarding IP multicast (Class D) datagrams based on the algorithms defined in the Multi- cast Extensions to OSPF. Bit 0, if set, indicates that the router can forward IP multicast datagrams in the router's directly attached areas (called intra-area mul- ticast routing). Bit 1, if set, indicates that the router can forward IP multicast datagrams between OSPF areas (called inter-area multicast routing). Bit 2, if set, indicates that the router can forward IP multicast datagrams between Auto- nomous Systems (called inter-AS multicast rout- ing). Only certain combinations of bit settings are allowed, namely: 0 (no multicast forwarding is enabled), 1 (intra-area multicasting only), 3 (intra-area and inter-area multicasting), 5 (intra-area and inter-AS multicasting) and 7 (multicasting everywhere). By default, no mul- ticast forwarding is enabled.
INT wfOspfMulticastDeterministic	1.3.6.1.4.1.18.3.5.3.2.3.1.22	INTEGER	read-write	This controls whether or not the deterministic variation of the MOSPF Dijkstra is run or not
INT wfOspfMulticastRoutePinning	1.3.6.1.4.1.18.3.5.3.2.3.1.23	INTEGER	read-write	This controls whether or not the route pinning variation of the MOSPF Dijkstra is run or not
INT wfOspfOpaqueCapability	1.3.6.1.4.1.18.3.5.3.2.3.1.24	INTEGER	read-write	This controls whether or not the router will accept and process OPAQUE LSAs
INT wfOspfDeterministicMcastHoldDown	1.3.6.1.4.1.18.3.5.3.2.3.1.25	INTEGER	read-write	This controls whether or not the Hold Down feature for the Deterministic MOSPF is enabled. If it is enabled, a data flow does not go out of an interface even if it would when the feature is disabled, unless there is a reservation for the flow on the interface
INT wfMospfEntryTimeoutValue	1.3.6.1.4.1.18.3.5.3.2.3.1.26	INTEGER	read-write	The timer value for timing out MOSPF forward entries.
INT wfOspfMaxQueuedMcastPkts	1.3.6.1.4.1.18.3.5.3.2.3.1.27	INTEGER	read-write	This controls how many mcast packets can be queued on each slot for all flows before the building of mcast trees finishes. If it is not 0, the first a few data packets for a mcast flow are queued before the building of the mcast tree finishes. Otherwise, packets are quietly dropped before the tree is calculated.
INT wfOspfMcastUseDynTTL	1.3.6.1.4.1.18.3.5.3.2.3.1.28	INTEGER	read-write	This controls whether dynamic TTL threshold is used. Data forwarding is a little bit faster when it is NOT used. Dynamic TTL means the TTL threshold may be different per (source, group, downstream) tuple. See MOSPF spec, section 2.3.4.
INT wfOspfRfc1583Compatibility	1.3.6.1.4.1.18.3.5.3.2.3.1.29	INTEGER	read-write	Controls the preference rules used when choosing among multiple AS-external-LSAs advertising the same destination. When set to 'enabled', the preference rules remain those specified by RFC 1583. When set to 'disabled', the preference rules are those stated in RFC 2178, which prevent routing loops when AS- external-LSAs for the same destination have been originated from different areas.
INT wfOspfASEMcastEnable	1.3.6.1.4.1.18.3.5.3.2.3.1.30	INTEGER	read-write	This attribute indicates whether AS External routes are multicast capable. If enabled, the advertising ASBR sets the MC-bit in the ASE-LSAs for those routes, so that they can be used for multicast purpose. If an MOSPF router works as an ASBR to support IGMP Relay, it should has this attribute set to 'enabled'. By default, all external routes are multicast incapable. If it's known that an ASBR's external routes can only be used for unicast, this attribute must be set to 'disabled' on the ASBR. For example, if an ASBR has a BGP connection to an ISP but the routes learned via BGP can't be used for multicast because external multicast traffic should be injected by another router with a DVMRP tunnel to Mbone, this attribute on the ASBR should be set to 'disabled'.
INT wfOspfNssaBorderRouter	1.3.6.1.4.1.18.3.5.3.2.3.1.31	INTEGER	read-only	`A flag to note whether this router NSSA border router'
INT wfOspfLsaRefreshMax	1.3.6.1.4.1.18.3.5.3.2.3.1.32	INTEGER	read-write	`Maximum number of consecutive refreshes of self-originated Summary and External LSAs before applying a configured delay. A value of zero implies that there is no maximum.'
INT wfOspfLsaRefreshDelay	1.3.6.1.4.1.18.3.5.3.2.3.1.33	INTEGER	read-write	`Delay to apply between the maximum number of consecutive refreshes of self-originated Summary and External LSAs if a non-zero maximum is configured. The unit of delay is in seconds.'
INT wfOspfAggrUseMaxCost	1.3.6.1.4.1.18.3.5.3.2.3.1.34	INTEGER	read-write	When area range is configured, sum net lsa is generated depends on this mib attribute: enabled: Use Max Metric to aggregate networks. See RFC2328 3.5 IP subnetting support. disabled: Use Min Metric to aggregate networks. Bay Router pre-14.40 version does this way.
INT wfOspfFwdAddrComp	1.3.6.1.4.1.18.3.5.3.2.3.1.35	INTEGER	read-write	When enabled allows OSPF to comply with RFC1583 with respect to forwarding address changes. When disabled OSPF remains compatiable with pre-14.00rev1D code.
INT wfOspfMtuUseCommonDefault	1.3.6.1.4.1.18.3.5.3.2.3.1.36	INTEGER	read-write	when this parameter is enabled, OSPF will use the MTU size of ethernet, that is, 1500 in all the interfaces regardless of what IP passes onto OSPF if the wfOspfMtuSize at the interface is set to 1(= Default) or 2. If wfOspfMtuSize is greater than 2 then OSPF will use wfOspfMtuSize as the MTU size at the interface.
wfOspfAreaTable	1.3.6.1.4.1.18.3.5.3.2.3.2		not-accessible	-- The OSPF Area Data Structure contains information -- regarding the various areas. The interfaces and -- virtual links are configured as part of these areas. -- Area 0.0.0.0, by definition, is the Backbone Area 'Information describing the configured parameters and cumulative statistics of the router's attached areas.' REFERENCE 'OSPF Version 2, Section 6 The Area Data Structure'
wfOspfAreaEntry	1.3.6.1.4.1.18.3.5.3.2.3.2.1		not-accessible	'Information describing the configured parameters and cumulative statistics of one of the router's attached areas.'
INT wfOspfAreaDelete	1.3.6.1.4.1.18.3.5.3.2.3.2.1.1	INTEGER	read-write	This value determines if the OSPF router is configured with this area.
INT wfOspfAreaDisable	1.3.6.1.4.1.18.3.5.3.2.3.2.1.2	INTEGER	read-write	This value indicates the state of this area on the OSPF router.
INT wfOspfAreaState	1.3.6.1.4.1.18.3.5.3.2.3.2.1.3	INTEGER	read-only	This value indicates the state of the OSPF Area.
IP wfOspfAreaId	1.3.6.1.4.1.18.3.5.3.2.3.2.1.4	IpAddress	read-only	'A 32-bit integer uniquely identifying an area. Area ID 0.0.0.0 is used for the OSPF backbone.' REFERENCE 'OSPF Version 2, Appendix C.2 Area parameters'
INT wfOspfAuthType	1.3.6.1.4.1.18.3.5.3.2.3.2.1.5	INTEGER	read-write	'The authentication type specified for an area. Additional authentication types may be assigned locally on a per Area basis.' REFERENCE 'OSPF Version 2, Appendix E Authentication' -- none (0), -- simplePassword (1) -- reserved for future specification (2..255) -- reserved for AS specific values (> 255)
INT wfOspfImportASExtern	1.3.6.1.4.1.18.3.5.3.2.3.2.1.6	INTEGER	read-write	'The area's support for importing AS external link- state advertisements.' REFERENCE `OSPF NSSA Internet Draft, Appendix D: Configuration Parameters'
INT wfOspfStubMetric	1.3.6.1.4.1.18.3.5.3.2.3.2.1.7	INTEGER	read-write	'The metric value applied at the indicated type of service. By default, this equals the least metric at the type of service among the interfaces to other areas.'
INT wfOspfImportSum	1.3.6.1.4.1.18.3.5.3.2.3.2.1.8	INTEGER	read-write	'The area's support for importing Summary advertisements into a stub area. This variable should not be set unless wfOspfImportASExtern is set to FALSE'
CTR wfOspfSpfCnt	1.3.6.1.4.1.18.3.5.3.2.3.2.1.9	Counter	read-only	The number of times the OSPF SPF algorithm has been run for this area.
INT wfOspfPtpSpecCostEnable	1.3.6.1.4.1.18.3.5.3.2.3.2.1.10	INTEGER	read-write	This value indicates the formula used to calculate the cost for point to point links.
INT wfOspfAreaNssaTranslateCfg	1.3.6.1.4.1.18.3.5.3.2.3.2.1.11	INTEGER	read-write	`Indicates whether or not an NSSA Border routes is configured to performing NSSA translation of type-7 LSAs into type-5 LSAs.' REFERENCE `OSPF NSSA Internet Draft, Appendix D: Configuration Parameters'
INT wfOspfAreaNssaTranslateStatus	1.3.6.1.4.1.18.3.5.3.2.3.2.1.12	INTEGER	read-only	`Indicates whether or not an NSSA Border routes is performing NSSA translation of type-7 LSAs into type-5 LSAs.' REFERENCE `OSPF NSSA Internet Draft, Appendix D: Configuration Parameters'
INT wfOspfAreaNssaOriginateDefaultRoute	1.3.6.1.4.1.18.3.5.3.2.3.2.1.13	INTEGER	read-write	`whether or not an Type-7 default is originated by the ASBR'
INT wfOspfAreaNssaPropagateDefaultRoute	1.3.6.1.4.1.18.3.5.3.2.3.2.1.14	INTEGER	read-write	`Indicates whether or not the Type-7 default route LSA will have the propagate bit (P-bit) set. If the P-bit is set, the Type-7 default route LSA is translated into a Type-5 default route LSA and the Type-5 default route LSA is flooded into all non-stub areas. Otherwise the Type-7 default route LSA is not translated This parameter applies to NSSA internal ASBR only. For NSSA border ASBR, the P-bit is never set'
INT wfOspfAreaNssaDefaultRoutePathType	1.3.6.1.4.1.18.3.5.3.2.3.2.1.15	INTEGER	read-write	`The path type applied to the type-7 default route' REFERENCE `OSPF NSSA Internet Draft, Appendix D: Configuration Parameters'
wfOspfLsdbTable	1.3.6.1.4.1.18.3.5.3.2.3.3		not-accessible	-- OSPF Link State Database -- The Link State Database contains the Link State -- Advertisements from throughout the areas that the -- device is attached to. 'The OSPF Process's Links State Database.' REFERENCE 'OSPF Version 2, Section 12 Link State Advertisements'
wfOspfLsdbEntry	1.3.6.1.4.1.18.3.5.3.2.3.3.1		not-accessible	'A single Link State Advertisement.'
IP wfOspfLsdbAreaId	1.3.6.1.4.1.18.3.5.3.2.3.3.1.1	IpAddress	read-only	'The 32 bit identifier of the Area from which the LSA was received.' REFERENCE 'OSPF Version 2, Appendix C.2 Area parameters'
INT wfOspfLsdbType	1.3.6.1.4.1.18.3.5.3.2.3.3.1.2	INTEGER	read-only	'The type of the link state advertisement. Each link state type has a separate advertisement format.' REFERENCE 'OSPF Version 2, Appendix A.4.1 The Link State Advertisement header' stubLink (0), routerLink (1), networkLink (2), summaryLink (3), asSummaryLink (4), asExternalLink (5), multicastlink (6), opaquelink (15), resourcelink (16)
IP wfOspfLsdbLSID	1.3.6.1.4.1.18.3.5.3.2.3.3.1.3	IpAddress	read-only	'The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement.' REFERENCE 'OSPF Version 2, Section 12.1.4 Link State ID'
IP wfOspfLsdbRouterId	1.3.6.1.4.1.18.3.5.3.2.3.3.1.4	IpAddress	read-only	'The 32 bit number that uniquely identifies the originating router in the Autonomous System.' REFERENCE 'OSPF Version 2, Appendix C.1 Global parameters'
INT wfOspfLsdbSequence	1.3.6.1.4.1.18.3.5.3.2.3.3.1.5	INTEGER	read-only	-- Note that the OSPF Sequence Number is a 32 bit signed -- integer. It starts with the value '80000001'h, -- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h -- Thus, a typical sequence number will be very negative. 'The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.' REFERENCE 'OSPF Version 2, Section 12.1.6 LS sequence number'
INT wfOspfLsdbAge	1.3.6.1.4.1.18.3.5.3.2.3.3.1.6	INTEGER	read-only	'This field is the age of the link state advertisement in seconds.' (OSPF_LSDBMINAGE = 0) REFERENCE 'OSPF Version 2, Section 12.1.1 LS age'
INT wfOspfLsdbChecksum	1.3.6.1.4.1.18.3.5.3.2.3.3.1.7	INTEGER	read-only	'This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum.' REFERENCE 'OSPF Version 2, Section 12.1.7 LS checksum'
INT wfOspfLsdbMetric	1.3.6.1.4.1.18.3.5.3.2.3.3.1.8	INTEGER	read-only	'Metric from LSA, if applicable.'
IP wfOspfLsdbAseForwardAddr	1.3.6.1.4.1.18.3.5.3.2.3.3.1.9	IpAddress	read-only	'If an ASE, the forwarding address from the LSA.'
GAU wfOspfLsdbAseTag	1.3.6.1.4.1.18.3.5.3.2.3.3.1.10	Gauge	read-only	'If an ASE, the External Route Tag from the LSA.'
INT wfOspfLsdbAseType	1.3.6.1.4.1.18.3.5.3.2.3.3.1.11	INTEGER	read-only	'If an ASE, the external metric type from the LSA.'
INT wfOspfLsdbAdvLen	1.3.6.1.4.1.18.3.5.3.2.3.3.1.12	INTEGER	read-only	'The length of entire Link State Advertisement, including its header.' REFERENCE 'OSPF Version 2, Section 12 Link State Advertisements'
OCT wfOspfLsdbAdv	1.3.6.1.4.1.18.3.5.3.2.3.3.1.13	OCTET STRING	read-only	'This field is the actual OSPF advertisement in hexadecimal format'
wfOspfAreaRangeTable	1.3.6.1.4.1.18.3.5.3.2.3.4		not-accessible	'A range if IP addresses specified by an IP address/IP network mask pair. For example, class B address range of X.X.X.X with a network mask of 255.255.0.0 includes all IP addresses from X.X.0.0 to X.X.255.255' REFERENCE 'OSPF Version 2, Appendix C.2 Area parameters'
wfOspfAreaRangeEntry	1.3.6.1.4.1.18.3.5.3.2.3.4.1		not-accessible
INT wfOspfAreaRangeDelete	1.3.6.1.4.1.18.3.5.3.2.3.4.1.1	INTEGER	read-write	This value determines if an Area Range has been configured for the OSPF router.
INT wfOspfAreaRangeDisable	1.3.6.1.4.1.18.3.5.3.2.3.4.1.2	INTEGER	read-write	'This variable displays the status of the entry. Setting it to 'DISBALED' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.'
INT wfOspfAreaRangeState	1.3.6.1.4.1.18.3.5.3.2.3.4.1.3	INTEGER	read-only	The state of the OSPF Area Range.
IP wfOspfAreaRangeAreaID	1.3.6.1.4.1.18.3.5.3.2.3.4.1.4	IpAddress	read-only	'The Area the Address Range is to be found within.' REFERENCE 'OSPF Version 2, Appendix C.2 Area parameters'
IP wfOspfAreaRangeNet	1.3.6.1.4.1.18.3.5.3.2.3.4.1.5	IpAddress	read-only	'The IP Address of the Net or Subnet indicated by the range.' REFERENCE 'OSPF Version 2, Appendix C.2 Area parameters'
IP wfOspfAreaRangeMask	1.3.6.1.4.1.18.3.5.3.2.3.4.1.6	IpAddress	read-write	'The Subnet Mask that pertains to the Net or Subnet.' REFERENCE 'OSPF Version 2, Appendix C.2 Area parameters'
INT wfOspfAreaRangeStatus	1.3.6.1.4.1.18.3.5.3.2.3.4.1.7	INTEGER	read-write	'Set to either Advertise or DoNotAdvertise. Routing information is condensed at area boundaries. External to the area, at most a single route is advertised for each address range. The route is advertised if and only if the addre range's Status is set to Advertise. Unadvertised ranges allow the existence of certain networks to be intentionally hidden from other areas. Status is set to Advertise by default.' REFERENCE 'OSPF Version 2, Appendix C.2'
INT wfOspfAreaRangeMetric	1.3.6.1.4.1.18.3.5.3.2.3.4.1.8	INTEGER	read-write	'The metric to advertise into other areas as the distance from the OSPF router to any network in the range. The default of 0 means to use the value calculated by OSPF.' REFERENCE 'OSPF Version 2, Appendix C.2'
wfOspfIfTable	1.3.6.1.4.1.18.3.5.3.2.3.5		not-accessible	-- OSPF Interface Table -- The OSPF Interface Table augments the ifTable with OSPF -- specific information. 'The OSPF Interface Table describes the interfaces from the viewpoint of OSPF.' REFERENCE 'OSPF Version 2, Appendix C.3 Router interface parameters'
wfOspfIfEntry	1.3.6.1.4.1.18.3.5.3.2.3.5.1		not-accessible	'The OSPF Interface Entry describes one interface from the viewpoint of OSPF.'
INT wfOspfIfDelete	1.3.6.1.4.1.18.3.5.3.2.3.5.1.1	INTEGER	read-write	This variable determines in an OSPF Interface has been configured on the router.
INT wfOspfIfDisable	1.3.6.1.4.1.18.3.5.3.2.3.5.1.2	INTEGER	read-write	'The OSPF interface's administrative status. The value 'enabled' denotes that neighbor relationships may be formed on the interface, and the interface will be advertised as an internal route to some area. The value 'disabled' denotes that the interface is external to OSPF.'
INT wfOspfIfState	1.3.6.1.4.1.18.3.5.3.2.3.5.1.3	INTEGER	read-only	'The OSPF Interface State.' down (1), loopback (2), waiting (3), pointToPoint (4), designatedRouter (5), backupDesignatedRouter (6), otherDesignatedRouter (7)
IP wfOspfIfIpAddress	1.3.6.1.4.1.18.3.5.3.2.3.5.1.4	IpAddress	read-only	'The IP address of this OSPF interface.'
INT wfOspfAddressLessIf	1.3.6.1.4.1.18.3.5.3.2.3.5.1.5	INTEGER	read-only	'For the purpose of easing the instancing of addressed and addressless interfaces; This variable takes the value 0 on interfaces with IP Addresses, and the corresponding value of ifIndex for interfaces having no IP Address.'
IP wfOspfIfAreaId	1.3.6.1.4.1.18.3.5.3.2.3.5.1.6	IpAddress	read-write	'A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0.0.0.0 is used for the OSPF backbone.' default { '00000000'H } -- 0.0.0.0
INT wfOspfIfType	1.3.6.1.4.1.18.3.5.3.2.3.5.1.7	INTEGER	read-write	'The OSPF interface type. By way of a default, this field may be intuited from the corresponding value of ifType. Broadcast LANs, such as Ethernet and IEEE 802.5, take the value 'broadcast'. Medias which allow multiple devices to be connected but don't support a broadcast mechanism, such as X.25, take the value 'nbma'. Point to Point protocols take the value of 'pointtopoint'. Non-fully meshed technologies would take the value of either 'ietf' or 'pmp'. Passive interface take the value of 'passive'. An example topology is a Frame Relay cloud that does not have a PVC between every device on the cloud. broadcast (1), nbma (2), pointToPoint (3) point to multipoint - proprietary (4) point to multipoint - standard (5) passive (6)
INT wfOspfIfRtrPriority	1.3.6.1.4.1.18.3.5.3.2.3.5.1.8	INTEGER	read-write	'The priority of this interface. Used in multi-access networks, this field is used in the designated router election algorithm. The value 0 signifies that the router is not eligible to become the designated router on this particular network. In the event of a tie in this value, routers will use their router id as a tie breaker.'
INT wfOspfIfTransitDelay	1.3.6.1.4.1.18.3.5.3.2.3.5.1.9	INTEGER	read-write	'The estimated number of seconds it takes to transmit a link- state update packet over this interface.'
INT wfOspfIfRetransInterval	1.3.6.1.4.1.18.3.5.3.2.3.5.1.10	INTEGER	read-write	'The number of seconds between link-state advertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database description and link-state request packets.'
INT wfOspfIfHelloInterval	1.3.6.1.4.1.18.3.5.3.2.3.5.1.11	INTEGER	read-write	'The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for all routers attached to a common network.'
INT wfOspfIfRtrDeadInterval	1.3.6.1.4.1.18.3.5.3.2.3.5.1.12	INTEGER	read-write	'The number of seconds that a router's Hello packets have not been seen before it's neighbors declare the router down. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common network.'
INT wfOspfIfPollInterval	1.3.6.1.4.1.18.3.5.3.2.3.5.1.13	INTEGER	read-write	'The larger time interval, in seconds, between the Hello packets sent to an inactive non-broadcast multi- access neighbor.'
IP wfOspfIfDesignatedRouter	1.3.6.1.4.1.18.3.5.3.2.3.5.1.14	IpAddress	read-only	'The IP Address of the Designated Router.' default { '00000000'H } -- 0.0.0.0
IP wfOspfIfBackupDesignatedRouter	1.3.6.1.4.1.18.3.5.3.2.3.5.1.15	IpAddress	read-only	'The IP Address of the Backup Designated Router.' default { '00000000'H } -- 0.0.0.0
INT wfOspfIfMetricCost	1.3.6.1.4.1.18.3.5.3.2.3.5.1.16	INTEGER	read-write	'The cost of using this type of service on this interface. The default value of the TOS 0 Metric is 10^8 / ifSpeed. The value FFFF is distinguished to mean 'no route via this TOS'.'
OCT wfOspfIfAuthKey	1.3.6.1.4.1.18.3.5.3.2.3.5.1.17	OCTET STRING	read-write	'The Authentication Key. If the Area's Authorization Type is simplePassword, and the key length is shorter than 8 octets, the agent will left adjust and zero fill to 8 octets. When read, ospfIfAuthKey always returns an Octet String of length zero.' default { '0000000000000000'H } -- 0.0.0.0.0.0.0.0 REFERENCE 'OSPF Version 2, Section 9 The Interface Data Structure'
CTR wfOspfIfTxHellos	1.3.6.1.4.1.18.3.5.3.2.3.5.1.18	Counter	read-only	Number of OSPF Hello packets transmitted.
CTR wfOspfIfTxDBDescripts	1.3.6.1.4.1.18.3.5.3.2.3.5.1.19	Counter	read-only	Number of OSPF DataBase Description packets transmitted.
CTR wfOspfIfTxLinkStateReqs	1.3.6.1.4.1.18.3.5.3.2.3.5.1.20	Counter	read-only	Number of OSPF Link State Request packets transmitted.
CTR wfOspfIfTxLinkStateUpds	1.3.6.1.4.1.18.3.5.3.2.3.5.1.21	Counter	read-only	Number of OSPF Link State Update packets transmitted.
CTR wfOspfIfTxLinkStateAcks	1.3.6.1.4.1.18.3.5.3.2.3.5.1.22	Counter	read-only	Number of OSPF Link States Acknowledgements transmitted.
CTR wfOspfIfRxHellos	1.3.6.1.4.1.18.3.5.3.2.3.5.1.23	Counter	read-only	Number of OSPF Hello packets received.
CTR wfOspfIfRxDBDescripts	1.3.6.1.4.1.18.3.5.3.2.3.5.1.24	Counter	read-only	Number of OSPF DataBase Description packets received.
CTR wfOspfIfRxLinkStateReqs	1.3.6.1.4.1.18.3.5.3.2.3.5.1.25	Counter	read-only	Number of OSPF Link State Requests received.
CTR wfOspfIfRxLinkStateUpds	1.3.6.1.4.1.18.3.5.3.2.3.5.1.26	Counter	read-only	Number of OSPF Link State Updates received.
CTR wfOspfIfRxLinkStateAcks	1.3.6.1.4.1.18.3.5.3.2.3.5.1.27	Counter	read-only	Number of OSPF Link State Acknowledgements received.
CTR wfOspfIfDrops	1.3.6.1.4.1.18.3.5.3.2.3.5.1.28	Counter	read-only	Number of OSPF packets dropped because of invalid information in the packet.
INT wfOspfMtuSize	1.3.6.1.4.1.18.3.5.3.2.3.5.1.29	INTEGER	read-write	Configure MTU size per OSPF interface This parameter has the following values/meanings: 1 - Use the MTU specified by IP 2 - Use the MTU of ethernet, regardless of what IP says > 2 - Use this value as the actual MTU. If the value is smaller than what OSPF needs as a minimum then the mtu specified by IP is used. For example, 3 would never be used as an MTU.
INT wfOspfIfMulticastForwarding	1.3.6.1.4.1.18.3.5.3.2.3.5.1.30	INTEGER	read-write	The way multicasts should forwarded on this interface; not forwarded, forwarded as data link multicasts, or forwarded as data link uni- casts. Data link multicasting is not meaning- ful on point to point and NBMA interfaces, and setting ospfMulticastForwarding to 0 effective- ly disables all multicast forwarding.
INT wfOspfIfOpaqueOn	1.3.6.1.4.1.18.3.5.3.2.3.5.1.31	INTEGER	read-write	This controls whether or not OPAQUE LSAs are to be flooded out this interface or not.
INT wfOspfIfBwRate	1.3.6.1.4.1.18.3.5.3.2.3.5.1.32	INTEGER	read-only	Available BW (token bucket rate) on the intf
INT wfOspfIfBwDepth	1.3.6.1.4.1.18.3.5.3.2.3.5.1.33	INTEGER	read-only	Available BW (token bucket depth) on the intf
INT wfOspfIfMtuMismatchDetect	1.3.6.1.4.1.18.3.5.3.2.3.5.1.34	INTEGER	read-write	Controls the interpretation of the MTU field in the database description packet header. Per RFC 2178 the MTU indicates the largest size IP packet that an OSPF interface can receive. If the MTU is greater than that which the interface can receive the packet is ignored and thus, an adjacency is not formed. In RFC 1583 this field does not exist. The value 'enabled' denotes RFC 2178 processing of the MTU field. The value 'disabled' denotes RFC 1583 processing.
wfOspfVirtIfTable	1.3.6.1.4.1.18.3.5.3.2.3.6		not-accessible	-- OSPF Virtual Interface Table -- The Virtual Interface Table describes the virtual -- links that the OSPF Process is configured to -- carry on. 'Information about this router's virtual interfaces.' REFERENCE 'OSPF Version 2, Appendix C.4 Virtual link parameters'
wfOspfVirtIfEntry	1.3.6.1.4.1.18.3.5.3.2.3.6.1		not-accessible	'Information about a single Virtual Interface.'
INT wfOspfVirtIfDelete	1.3.6.1.4.1.18.3.5.3.2.3.6.1.1	INTEGER	read-write
INT wfOspfVirtIfDisable	1.3.6.1.4.1.18.3.5.3.2.3.6.1.2	INTEGER	read-write	'This variable displays the validity or invalidity of the entry. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.'
INT wfOspfVirtIfState	1.3.6.1.4.1.18.3.5.3.2.3.6.1.3	INTEGER	read-only	'OSPF virtual interface states.' down (1), -- these use the same encoding pointToPoint (4) -- as the ospfIfTable
IP wfOspfVirtIfAreaID	1.3.6.1.4.1.18.3.5.3.2.3.6.1.4	IpAddress	read-only	'The Transit Area that the Virtual Link traverses. By definition, this is not 0.0.0.0'
IP wfOspfVirtIfNeighbor	1.3.6.1.4.1.18.3.5.3.2.3.6.1.5	IpAddress	read-only	'The Router ID of the Virtual Neighbor.'
INT wfOspfVirtIfTransitDelay	1.3.6.1.4.1.18.3.5.3.2.3.6.1.6	INTEGER	read-write	'The estimated number of seconds it takes to transmit a link- state update packet over this interface.'
INT wfOspfVirtIfRetransInterval	1.3.6.1.4.1.18.3.5.3.2.3.6.1.7	INTEGER	read-write	'The number of seconds between link-state advertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database description and link-state request packets. This value should be well over the expected round-trip time.'
INT wfOspfVirtIfHelloInterval	1.3.6.1.4.1.18.3.5.3.2.3.6.1.8	INTEGER	read-write	'The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for the virtual neighbor.'
INT wfOspfVirtIfRtrDeadInterval	1.3.6.1.4.1.18.3.5.3.2.3.6.1.9	INTEGER	read-write	'The number of seconds that a router's Hello packets have not been seen before it's neighbors declare the router down. This should be some multiple of the Hello interval. This value must be the same for the virtual neighbor.'
OCT wfOspfVirtIfAuthKey	1.3.6.1.4.1.18.3.5.3.2.3.6.1.10	OCTET STRING	read-write	'If Authentication Type is simplePassword, the device will left adjust and zero fill to 8 octets. When read, ospfVifAuthKey always returns a string of length zero.' REFERENCE 'OSPF Version 2, Section 9 The Interface Data Structure'
CTR wfOspfVirtIfTxHellos	1.3.6.1.4.1.18.3.5.3.2.3.6.1.11	Counter	read-only	Number of OSPF Hello packets transmitted on Virtual Interfaces.
CTR wfOspfVirtIfTxDBDescripts	1.3.6.1.4.1.18.3.5.3.2.3.6.1.12	Counter	read-only	Number of OSPF DataBase Description packets transmitted on Virtual Interfaces.
CTR wfOspfVirtIfTxLinkStateReqs	1.3.6.1.4.1.18.3.5.3.2.3.6.1.13	Counter	read-only	Number of OSPF Link State Request packets transmitted on Virtual Interfaces.
CTR wfOspfVirtIfTxLinkStateUpds	1.3.6.1.4.1.18.3.5.3.2.3.6.1.14	Counter	read-only	Number of OSPF Link State Update packets transmitted on Virtual Interfaces.
CTR wfOspfVirtIfTxLinkStateAcks	1.3.6.1.4.1.18.3.5.3.2.3.6.1.15	Counter	read-only	Number of OSPF Link State Acknowledgement packets transmitted on Virtual Interfaces.
CTR wfOspfVirtIfRxHellos	1.3.6.1.4.1.18.3.5.3.2.3.6.1.16	Counter	read-only	Number of OSPF Hello packets received on Virtual Interfaces.
CTR wfOspfVirtIfRxDBDescripts	1.3.6.1.4.1.18.3.5.3.2.3.6.1.17	Counter	read-only	Number of OSPF DataBase Description packets received on Virtual Interfaces.
CTR wfOspfVirtIfRxLinkStateReqs	1.3.6.1.4.1.18.3.5.3.2.3.6.1.18	Counter	read-only	Number of OSPF Link State Request packets recieved on Virtual Interfaces.
CTR wfOspfVirtIfRxLinkStateUpds	1.3.6.1.4.1.18.3.5.3.2.3.6.1.19	Counter	read-only	Number of OSPF Link State Update packets received on Virtual Interfaces.
CTR wfOspfVirtIfRxLinkStateAcks	1.3.6.1.4.1.18.3.5.3.2.3.6.1.20	Counter	read-only	Number of OSPF Link State Acknowledgement packets received on Virtual Interfaces.
CTR wfOspfVirtIfDrops	1.3.6.1.4.1.18.3.5.3.2.3.6.1.21	Counter	read-only	Number of OSPF packets dropped on Virtual Interfaces.
wfOspfNbrTable	1.3.6.1.4.1.18.3.5.3.2.3.7		not-accessible	-- OSPF Neighbor Table -- The OSPF Neighbor Table describes all neighbors in -- the locality of the subject router. 'A table of non-virtual neighbor information.' REFERENCE 'OSPF Version 2, Section 10 The Neighbor Data Structure'
wfOspfNbrEntry	1.3.6.1.4.1.18.3.5.3.2.3.7.1		not-accessible	'The information regarding a single neighbor.' REFERENCE 'OSPF Version 2, Section 10 The Neighbor Data Structure'
INT wfOspfNbrDelete	1.3.6.1.4.1.18.3.5.3.2.3.7.1.1	INTEGER	read-write	This variable indicates the existence of a static OSPF neighbor.
INT wfOspfNbrDisable	1.3.6.1.4.1.18.3.5.3.2.3.7.1.2	INTEGER	read-write	'This variable displays the status of the entry. Setting it to 'DISABLED' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.'
INT wfOspfNbrState	1.3.6.1.4.1.18.3.5.3.2.3.7.1.3	INTEGER	read-only	'The State of the relationship with this Neighbor.' REFERENCE 'OSPF Version 2, Section 10.1 Neighbor States' down (1), attempt (2), init (3), twoWay (4), exchangeStart (5), exchange (6), loading (7), full (8)
IP wfOspfNbrIpAddr	1.3.6.1.4.1.18.3.5.3.2.3.7.1.4	IpAddress	read-only	'The IP address of this neighbor.'
IP wfOspfNbrIfAddr	1.3.6.1.4.1.18.3.5.3.2.3.7.1.5	IpAddress	read-write	'The Interface IP address for this neighbor.'
INT wfOspfNbrAddressLessIndex	1.3.6.1.4.1.18.3.5.3.2.3.7.1.6	INTEGER	read-only	' On an interface having an IP Address, zero. On addressless interfaces, the corresponding value of ifIndex in the Internet Standard MIB. On row creation, this can be derived from the instance.'
IP wfOspfNbrRtrId	1.3.6.1.4.1.18.3.5.3.2.3.7.1.7	IpAddress	read-only	'A 32-bit integer (represented as a type IpAddress) uniquely identifying the neighboring router in the Autonomous System.' default { '00000000'H } -- 0.0.0.0
INT wfOspfNbrOptions	1.3.6.1.4.1.18.3.5.3.2.3.7.1.8	INTEGER	read-only	'A Bit Mask corresponding to the neighbor's options field. Bit 0, if set, indicates that the area accepts and operates on external information; if zero, it is a stub area. Bit 1, if set, indicates that the system will operate on Type of Service metrics other than TOS 0. If zero, the neighbor will ignore all metrics except the TOS 0 metric.' REFERENCE 'OSPF Version 2, Section 12.1.2 Options'
INT wfOspfNbrPriority	1.3.6.1.4.1.18.3.5.3.2.3.7.1.9	INTEGER	read-write	'The priority of this neighbor in the designated router election algorithm. The value 0 signifies that the neighbor is not eligible to become the designated router on this particular network.' This is the user configurable/changeable neighbor's priority
CTR wfOspfNbrEvents	1.3.6.1.4.1.18.3.5.3.2.3.7.1.10	Counter	read-only	'The number of times this neighbor relationship has changed state, or an error has occurred.'
GAU wfOspfNbrLSRetransQLen	1.3.6.1.4.1.18.3.5.3.2.3.7.1.11	Gauge	read-only	'The current length of the retransmission queue.'
INT wfOspfCurNbrPriority	1.3.6.1.4.1.18.3.5.3.2.3.7.1.12	INTEGER	read-only	This value represents the priority of the neighbor as indicated in received Hello packets. In most cases, this will be the same as wfOspfCfgNbrPriority. If they are different, it indicates a misconfiguration
wfOspfVirtNbrTable	1.3.6.1.4.1.18.3.5.3.2.3.8		not-accessible	-- WFOSPF Virtual Neighbor Table -- This table describes all virtual neighbors. -- Since Virtual Links are configured in the -- virtual interface table, this table is read-only. 'A table of virtual neighbor information.' REFERENCE 'OSPF Version 2, '
wfOspfVirtNbrEntry	1.3.6.1.4.1.18.3.5.3.2.3.8.1		not-accessible	'Virtual neighbor information.' REFERENCE 'OSPF Version 2, '
IP wfOspfVirtNbrArea	1.3.6.1.4.1.18.3.5.3.2.3.8.1.1	IpAddress	read-only	'The Transit Area Identifier.'
IP wfOspfVirtNbrRtrId	1.3.6.1.4.1.18.3.5.3.2.3.8.1.2	IpAddress	read-only	'A 32-bit integer uniquely identifying the neighboring router in the Autonomous System.'
IP wfOspfVirtNbrIpAddr	1.3.6.1.4.1.18.3.5.3.2.3.8.1.3	IpAddress	read-only	'The IP address this Virtual Neighbor is using.'
INT wfOspfVirtNbrOptions	1.3.6.1.4.1.18.3.5.3.2.3.8.1.4	INTEGER	read-only	'A bit map corresponding to the neighbor's options field. Thus, Bit 1, if set, indicates that the neighbor supports Type of Service Routing; if zero, no metrics other than TOS 0 are in use by the neighbor.'
INT wfOspfVirtNbrState	1.3.6.1.4.1.18.3.5.3.2.3.8.1.5	INTEGER	read-only	'The state of the Virtual Neighbor Relationship.' down (1), attempt (2), init (3), twoWay (4), exchangeStart (5), exchange (6), loading (7), full (8)
CTR wfOspfVirtNbrEvents	1.3.6.1.4.1.18.3.5.3.2.3.8.1.6	Counter	read-only	'The number of times this virtual link has changed its state, or an error has occurred.'
GAU wfOspfVirtNbrLSRetransQLen	1.3.6.1.4.1.18.3.5.3.2.3.8.1.7	Gauge	read-only	'The current length of the retransmission queue.'
wfOspfDynNbrTable	1.3.6.1.4.1.18.3.5.3.2.3.9		not-accessible	-- OSPF Dynamic Neighbor Table -- The OSPF Dynamic Neighbor Table describes all neighbors in -- the locality of the subject router learned during operation. 'A table of non-virtual neighbor information.' REFERENCE 'OSPF Version 2, Section 10 The Neighbor Data Structure'
wfOspfDynNbrEntry	1.3.6.1.4.1.18.3.5.3.2.3.9.1		not-accessible	'The information regarding a single neighbor.' REFERENCE 'OSPF Version 2, Section 10 The Neighbor Data Structure'
INT wfOspfDynNbrState	1.3.6.1.4.1.18.3.5.3.2.3.9.1.1	INTEGER	read-only	'The State of the relationship with this Neighbor.' REFERENCE 'OSPF Version 2, Section 10.1 Neighbor States' down (1), attempt (2), init (3), twoWay (4), exchangeStart (5), exchange (6), loading (7), full (8)
IP wfOspfDynNbrIpAddr	1.3.6.1.4.1.18.3.5.3.2.3.9.1.2	IpAddress	read-only	'The IP address of this neighbor.'
IP wfOspfDynNbrIfAddr	1.3.6.1.4.1.18.3.5.3.2.3.9.1.3	IpAddress	read-only	'The Interface IP address for this neighbor.'
INT wfOspfDynNbrAddressLessIndex	1.3.6.1.4.1.18.3.5.3.2.3.9.1.4	INTEGER	read-only	' On an interface having an IP Address, zero. On addressless interfaces, the corresponding value of ifIndex in the Internet Standard MIB. On row creation, this can be derived from the instance.'
IP wfOspfDynNbrRtrId	1.3.6.1.4.1.18.3.5.3.2.3.9.1.5	IpAddress	read-only	'A 32-bit integer (represented as a type IpAddress) uniquely identifying the neighboring router in the Autonomous System.' default { '00000000'H } -- 0.0.0.0
INT wfOspfDynNbrOptions	1.3.6.1.4.1.18.3.5.3.2.3.9.1.6	INTEGER	read-only	'A Bit Mask corresponding to the neighbor's options field. Bit 0, if set, indicates that the area accepts and operates on external information; if zero, it is a stub area. Bit 1, if set, indicates that the system will operate on Type of Service metrics other than TOS 0. If zero, the neighbor will ignore all metrics except the TOS 0 metric.' REFERENCE 'OSPF Version 2, Section 12.1.2 Options'
INT wfOspfDynNbrPriority	1.3.6.1.4.1.18.3.5.3.2.3.9.1.7	INTEGER	read-only	'The priority of this neighbor in the designated router election algorithm. The value 0 signifies that the neighbor is not eligible to become the designated router on this particular network.'
CTR wfOspfDynNbrEvents	1.3.6.1.4.1.18.3.5.3.2.3.9.1.8	Counter	read-only	'The number of times this neighbor relationship has changed state, or an error has occurred.'
GAU wfOspfDynNbrLSRetransQLen	1.3.6.1.4.1.18.3.5.3.2.3.9.1.9	Gauge	read-only	'The current length of the retransmission queue.'
wfOspfBackupLsdbTable	1.3.6.1.4.1.18.3.5.3.2.3.10		not-accessible	-- OSPF Backup Link State Database -- The Backup Link State Database contains the Link State -- Advertisements from throughout the areas that the -- device is attached to. 'The OSPF Process's Links State Database.' REFERENCE 'OSPF Version 2, Section 12 Link State Advertisements'
wfOspfBackupLsdbEntry	1.3.6.1.4.1.18.3.5.3.2.3.10.1		not-accessible	'A single Link State Advertisement.'
IP wfOspfBackupLsdbAreaId	1.3.6.1.4.1.18.3.5.3.2.3.10.1.1	IpAddress	read-only	'The 32 bit identifier of the Area from which the LSA was received.' REFERENCE 'OSPF Version 2, Appendix C.2 Area parameters'
INT wfOspfBackupLsdbType	1.3.6.1.4.1.18.3.5.3.2.3.10.1.2	INTEGER	read-only	'The type of the link state advertisement. Each link state type has a separate advertisement format.' REFERENCE 'OSPF Version 2, Appendix A.4.1 The Link State Advertisement header' stubLink (0), routerLink (1), networkLink (2), summaryLink (3), asSummaryLink (4), asExternalLink (5)
IP wfOspfBackupLsdbLSID	1.3.6.1.4.1.18.3.5.3.2.3.10.1.3	IpAddress	read-only	'The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement.' REFERENCE 'OSPF Version 2, Section 12.1.4 Link State ID'
IP wfOspfBackupLsdbRouterId	1.3.6.1.4.1.18.3.5.3.2.3.10.1.4	IpAddress	read-only	'The 32 bit number that uniquely identifies the originating router in the Autonomous System.' REFERENCE 'OSPF Version 2, Appendix C.1 Global parameters'
INT wfOspfBackupLsdbSequence	1.3.6.1.4.1.18.3.5.3.2.3.10.1.5	INTEGER	read-only	-- Note that the OSPF Sequence Number is a 32 bit signed -- integer. It starts with the value '80000001'h, -- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h -- Thus, a typical sequence number will be very negative. 'The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.' REFERENCE 'OSPF Version 2, Section 12.1.6 LS sequence number'
INT wfOspfBackupLsdbAge	1.3.6.1.4.1.18.3.5.3.2.3.10.1.6	INTEGER	read-only	'This field is the age of the link state advertisement in seconds.' (OSPF_LSDBMINAGE = 0) REFERENCE 'OSPF Version 2, Section 12.1.1 LS age'
INT wfOspfBackupLsdbChecksum	1.3.6.1.4.1.18.3.5.3.2.3.10.1.7	INTEGER	read-only	'This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum.' REFERENCE 'OSPF Version 2, Section 12.1.7 LS checksum'
INT wfOspfBackupLsdbMetric	1.3.6.1.4.1.18.3.5.3.2.3.10.1.8	INTEGER	read-only	'Metric from LSA, if applicable.'
IP wfOspfBackupLsdbAseForwardAddr	1.3.6.1.4.1.18.3.5.3.2.3.10.1.9	IpAddress	read-only	'If an ASE, the forwarding address from the LSA.'
GAU wfOspfBackupLsdbAseTag	1.3.6.1.4.1.18.3.5.3.2.3.10.1.10	Gauge	read-only	'If an ASE, the External Route Tag from the LSA.'
INT wfOspfBackupLsdbAseType	1.3.6.1.4.1.18.3.5.3.2.3.10.1.11	INTEGER	read-only	'If an ASE, the external metric type from the LSA.'
INT wfOspfBackupLsdbAdvLen	1.3.6.1.4.1.18.3.5.3.2.3.10.1.12	INTEGER	read-only	'The length of entire Link State Advertisement, including its header.' REFERENCE 'OSPF Version 2, Section 12 Link State Advertisements'
OCT wfOspfBackupLsdbAdv	1.3.6.1.4.1.18.3.5.3.2.3.10.1.13	OCTET STRING	read-only	'This field is the actual OSPF advertisement in hexadecimal format'
wfMospfForwardTable	1.3.6.1.4.1.18.3.5.3.2.3.11		not-accessible
wfMospfForwardEntry	1.3.6.1.4.1.18.3.5.3.2.3.11.1		not-accessible	A forwarding entry
IP wfMospfForwardSource	1.3.6.1.4.1.18.3.5.3.2.3.11.1.1	IpAddress	read-only	The source IP address of this entry. It could be either a host, or a network, depending upon the value of wfMospfForwardSourceMask
IP wfMospfForwardGroup	1.3.6.1.4.1.18.3.5.3.2.3.11.1.2	IpAddress	read-only	The destinatino group address of this entry
IP wfMospfForwardSourceMask	1.3.6.1.4.1.18.3.5.3.2.3.11.1.3	IpAddress	read-only	The mask for the source of this entry.
IP wfMospfForwardSourceNetMask	1.3.6.1.4.1.18.3.5.3.2.3.11.1.4	IpAddress	read-only	The mask for the network that the source is on.
INT wfMospfForwardFlag	1.3.6.1.4.1.18.3.5.3.2.3.11.1.5	INTEGER	read-only	Flags associated with the entry. 0x10000000 (re)calculation of the entry not done yet 0x00000001 the entry is associated with a RSVP session
IP wfMospfForwardUpstreamAddress	1.3.6.1.4.1.18.3.5.3.2.3.11.1.6	IpAddress	read-only	The IP address of the upstream intf for the entry.
INT wfMospfForwardUpstreamIfIndex	1.3.6.1.4.1.18.3.5.3.2.3.11.1.7	INTEGER	read-only	The circuit number of the upstream intf for the entry.
INT wfMospfForwardBwBucketDepth	1.3.6.1.4.1.18.3.5.3.2.3.11.1.8	INTEGER	read-only	Depth parameter of the flow spec for the entry
INT wfMospfForwardBwBucketRate	1.3.6.1.4.1.18.3.5.3.2.3.11.1.9	INTEGER	read-only	Rate parameter of the flow spec for the entry
INT wfMospfForwardAge	1.3.6.1.4.1.18.3.5.3.2.3.11.1.10	INTEGER	read-only	The number of seconds since this route was last updated or otherwise determined to be correct.
OCT wfMospfForwardDownstream	1.3.6.1.4.1.18.3.5.3.2.3.11.1.11	OCTET STRING	read-only	list of downstream intfs for this entry. Each one is in the format of (intf_addr (u_int32), intf_cct (u_int16), ttl (u_int16))
wfOspfNSSARangeTable	1.3.6.1.4.1.18.3.5.3.2.3.12		not-accessible	-- OSPF NSSA Range Table -- The OSPF NSSA Range Table describes the Type-7 address -- ranges used in translation/aggregation of Type-7 LSAs -- into Type-5 LSAs. REFERENCE 'OSPF Internet Draft, Section 3.2 Type-7 Address Range'
wfOspfNSSARangeEntry	1.3.6.1.4.1.18.3.5.3.2.3.12.1		not-accessible
INT wfOspfNSSARangeDelete	1.3.6.1.4.1.18.3.5.3.2.3.12.1.1	INTEGER	read-write	This value determines if an type-7 Range has been configured for the OSPF NSSA border router .
INT wfOspfNSSARangeDisable	1.3.6.1.4.1.18.3.5.3.2.3.12.1.2	INTEGER	read-write	`This variable displays the status of the entry. Setting it to `DISBALED' has the effect of rendering it inoperative. '
IP wfOspfNSSARangeNet	1.3.6.1.4.1.18.3.5.3.2.3.12.1.3	IpAddress	read-only	`The IP Address of the Net or Subnet indicated by the range.' REFERENCE `OSPF NSSA Internet Draft, 3.2 type-7 address range'
IP wfOspfNSSARangeMask	1.3.6.1.4.1.18.3.5.3.2.3.12.1.4	IpAddress	read-write	`The Subnet Mask that pertains to the Net or Subnet.' REFERENCE `OSPF NSSA Internet Draft, 3.2 type-7 address range'
INT wfOspfNSSARangeStatus	1.3.6.1.4.1.18.3.5.3.2.3.12.1.5	INTEGER	read-write	`Set to either Advertise or DoNotAdvertise. Routing information is condensed at area boundaries. External to the area, at most a single route is advertised for each address range. The route is advertised if and only if the addre range's Status is set to Advertise. Unadvertised ranges allow the existence of certain networks to be intentionally hidden from other areas. Status is set to Advertise by default.' REFERENCE `OSPF NSSA Internet Draft, 3.2 type-7 address range'
INT wfOspfNSSARangeExternRouteTag	1.3.6.1.4.1.18.3.5.3.2.3.12.1.6	INTEGER	read-write	`External route tag. This value is used in the aggregated type-5 LSA' REFERENCE `OSPF NSSA Internet Draft, 3.2 type-7 address range'

RFC description

Manages OSPF routing protocol configuration and state on Wellfleet/Nortel router platforms.

Start monitoring Wellfleet/Bay Networks routers (OSPF neighbor-adjacency/LSA-database status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Wellfleet-OSPF-MIB

What Is Wellfleet-OSPF-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description