Wellfleet-IPV6-MIB

All MIBs › Wellfleet-IPV6-MIB

Category: Wellfleet BayNetworks Routing Protocols

Description: Manages Wellfleet IPv6 interface addresses, neighbor discovery parameters, and routing table statistics.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Wellfleet-IPV6-MIB?

This is a vendor-specific proprietary MIB from Wellfleet Communications (later Bay Networks/Nortel), an early implementation for managing IPv6 on its multiprotocol routers, predating widespread IPv6 deployment. It exposes IPv6 interface address assignments, neighbor discovery protocol state, and routing table statistics. It supports software status monitoring because neighbor discovery cache state and routing table size reflect whether IPv6 reachability and route learning are functioning correctly on that router. It conceptually parallels the standard IETF IPv6 MIBs (RFC 2465/2466) though implemented as a Wellfleet-proprietary equivalent from that era. It is typically deployed on Wellfleet/Bay Networks routers that were early adopters piloting IPv6 alongside IPv4 in dual-stack network environments. Engineers can download the Wellfleet-IPV6-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in Wellfleet-IPV6-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Wellfleet/Bay Networks routers running IPv6

Monitoring Examples

No sample_objects were provided for this module; based on the short_desc, an operator would poll per-interface IPv6 address tables and the neighbor discovery cache for reachability state of adjacent nodes. A neighbor entry stuck in an 'incomplete' or 'stale' state, or a shrinking IPv6 routing table, would indicate a neighbor discovery failure or route withdrawal affecting IPv6 connectivity.

What Can Be Monitored

IPv6 interface address assignment
neighbor discovery cache entry state
IPv6 routing table size

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter
Gauge
IpAddress
TimeTicks

From RFC1213-MIB

DisplayString
PhysAddress

From Wellfleet-COMMON-MIB

wfIpv6Group

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
ADR wfIpv6AddrAddress	1.3.6.1.4.1.18.3.5.3.16.1.1.4.1.2	Ipv6Address	read-only	The IPv6 address to which this entry's addressing information pertains.
INT wfIpv6AddrAnycastFlag	1.3.6.1.4.1.18.3.5.3.16.1.1.4.1.5	INTEGER	read-only	This object has the value 'true(1)', if this address is an anycast address and the value 'false(2)' otherwise.
wfIpv6AddrEntry	1.3.6.1.4.1.18.3.5.3.16.1.1.4.1		not-accessible	The addressing information for one of this node's interface addresses.
INT wfIpv6AddrIfIndex	1.3.6.1.4.1.18.3.5.3.16.1.1.4.1.1	INTEGER	read-only	The index value which uniquely identifies the IPv6 interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of wfIpv6IfIndex.
INT wfIpv6AddrPfxLength	1.3.6.1.4.1.18.3.5.3.16.1.1.4.1.3	INTEGER	read-only	The length of the prefix (in bits) associated with the IPv6 address of this entry.
ADR wfIpv6AddrPrefix	1.3.6.1.4.1.18.3.5.3.16.1.1.3.1.5	Ipv6AddressPrefix	read-write	The prefix associated with the IPv6 address of this interface.
INT wfIpv6AddrPrefixAdvPreferredLifetime	1.3.6.1.4.1.18.3.5.3.16.1.1.3.1.11	INTEGER	read-write	The value to be placed in the Preferred Lifetime field in the Prefix Information option of Router Advertisements. It is the length of time in seconds (relative to the time the Router Advertisement is sent) that this prefix will remain preferred, i.e. time until deprecation. A value of 0xffffffff represents infinity. The address generated from a deprecated prefix should no longer be used as a source address in new communications, but packets received on such an interface are processed as expected.
INT wfIpv6AddrPrefixAdvValidLifetime	1.3.6.1.4.1.18.3.5.3.16.1.1.3.1.12	INTEGER	read-write	The value to be placed in the Valid Lifetime field in the Prefix Information option of Router Advertisements. It is the length of time in seconds (relative to the time the Router Advertisement is sent) that this prefix will remain valid, i.e. time until invalidation. A value of 0xffffffff (-1) represents infinity. The address generated from an invalidated prefix should not appear as the destination or source address of a packet.
INT wfIpv6AddrPrefixAnycast	1.3.6.1.4.1.18.3.5.3.16.1.1.3.1.14	INTEGER	read-only	Whether this prefix is an anycast address prefix: true - anycast address prefix, false - unicast address prefix.
INT wfIpv6AddrPrefixAutonomousFlag	1.3.6.1.4.1.18.3.5.3.16.1.1.3.1.10	INTEGER	read-write	Autonomous address configuration flag. When set (1), indicates that this prefix can be used for autonomous address configuration (i.e. can be used to form a local interface address). If off(2), it is not used to form a local interface address but it is advertised in ND's Router Advertisements.
INT wfIpv6AddrPrefixCost	1.3.6.1.4.1.18.3.5.3.16.1.1.3.1.8	INTEGER	read-write	The Cost metric associated with this entry. (Used as the RIP metric)
INT wfIpv6AddrPrefixDelete	1.3.6.1.4.1.18.3.5.3.16.1.1.3.1.1	INTEGER	read-write	Create/Delete parameter. Default is created. Users perform a set operation on this object in order to create/delete this prefix entry.
INT wfIpv6AddrPrefixDisable	1.3.6.1.4.1.18.3.5.3.16.1.1.3.1.2	INTEGER	read-write	Enable/Disable parameter. Default is enabled. Users perform a set operation on this object in order to enable/disable the use of a given prefix.
wfIpv6AddrPrefixEntry	1.3.6.1.4.1.18.3.5.3.16.1.1.3.1		not-accessible	An interface entry containing objects of a particular IPv6 address prefix.
INT wfIpv6AddrPrefixIfIndex	1.3.6.1.4.1.18.3.5.3.16.1.1.3.1.3	INTEGER	read-only	The index value which uniquely identifies the IPv6 interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of wfIpv6IfIndex.
INT wfIpv6AddrPrefixIndex	1.3.6.1.4.1.18.3.5.3.16.1.1.3.1.4	INTEGER	read-only	A index value identifying this prefix on the IPv6 interface to which this entry's addressing information pertains.
INT wfIpv6AddrPrefixInvalid	1.3.6.1.4.1.18.3.5.3.16.1.1.3.1.13	INTEGER	read-only	Whether this entry is valid or not: valid - usable prefix, invalid - misconfigured.
INT wfIpv6AddrPrefixLength	1.3.6.1.4.1.18.3.5.3.16.1.1.3.1.6	INTEGER	read-write	The length of the prefix (in bits) associated with the IPv6 address of this entry. A prefix can not be shorter than 3 bits.
INT wfIpv6AddrPrefixOnLinkFlag	1.3.6.1.4.1.18.3.5.3.16.1.1.3.1.9	INTEGER	read-write	On-link flag. When set (1), indicates that this prefix can be used for on-link determination.
INT wfIpv6AddrPrefixPreference	1.3.6.1.4.1.18.3.5.3.16.1.1.3.1.7	INTEGER	read-write	The Routing Preference in 0 to 15 range. A value of 15 is `most preferred'. Default 15.
wfIpv6AddrPrefixTable	1.3.6.1.4.1.18.3.5.3.16.1.1.3		not-accessible	The list of IPv6 address prefixes of IPv6 interfaces.
INT wfIpv6AddrStatus	1.3.6.1.4.1.18.3.5.3.16.1.1.4.1.6	INTEGER	read-only	Address status. The preferred(1) state indicates that this is a valid address that can appear as the destination or source address of a packet. The deprecated(2) this is a valid but deprecated address that should no longer be used as a source address in new communications, but packets addressed to such an address are processed as expected. The invalid(3) state indicates that this is not valid address which should not appear as the destination or source address of a packet. The inaccessible(4) state indicates the address is not accessible because the interface to which this address is assigned is not operational.
wfIpv6AddrTable	1.3.6.1.4.1.18.3.5.3.16.1.1.4		not-accessible	The table of addressing information relevant to this node's interface addresses.
INT wfIpv6AddrType	1.3.6.1.4.1.18.3.5.3.16.1.1.4.1.4	INTEGER	read-only	The type of address. Note that 'stateless(2)' refers to an address that was statelessly autoconfigured; 'stateful(3)' refers to a address which was acquired by via a stateful protocol (e.g. DHCPv6, manual configuration)
wfIpv6AdjacentNodeEntry	1.3.6.1.4.1.18.3.5.3.16.1.1.7.1		not-accessible	A description of an adjacent node
wfIpv6AdjacentNodeTable	1.3.6.1.4.1.18.3.5.3.16.1.1.7		not-accessible	The list of Adjacent Static Nodes (static IPv6->MAC resolutions)
ADR wfIpv6AdjNodeAddress	1.3.6.1.4.1.18.3.5.3.16.1.1.7.1.3	Ipv6Address	read-only	The IPv6 address of this Adjacent Node
INT wfIpv6AdjNodeCost	1.3.6.1.4.1.18.3.5.3.16.1.1.7.1.8	INTEGER	read-write	The Cost of this Adjacent Node. (Used as the RIP metric)
INT wfIpv6AdjNodeDelete	1.3.6.1.4.1.18.3.5.3.16.1.1.7.1.1	INTEGER	read-write	Whether to Delete this Adjacent Node
INT wfIpv6AdjNodeDisable	1.3.6.1.4.1.18.3.5.3.16.1.1.7.1.2	INTEGER	read-write	Whether to Disable this Adjacent Node
INT wfIpv6AdjNodeEncaps	1.3.6.1.4.1.18.3.5.3.16.1.1.7.1.6	INTEGER	read-write	The link layer encapsulation type of this entry. 'Snap(2)' is to be specified only if IEEE 802.2 encapsulation is to be used over CSMACD or DS1 links. For 'pdn(4)', X.121 address is stored in wfIpv6AdjNodeWanAddr. For 'wan(3)', X.121 or E.164 FR address is stored in wfIpv6AdjNodeWanAddr.
INT wfIpv6AdjNodeIfIndex	1.3.6.1.4.1.18.3.5.3.16.1.1.7.1.4	INTEGER	read-only	The index value which uniquely identifies the local IPv6 interface through which this Adjacent Node should be reached. The interface identified by a particular value of this index is the same interface as identified by the same value of wfIpv6IfIndex. If this index is zero, this Adjacent Node is this router itself, i.e. 'wfIpv6AdjNodeAddress' address is treated as a router's own local address. IPv6 datagrams with such a destination address are considered to be consumed by this router itself. As an example, such an address can be an IPv6 anycast address assigned to this router.
INT wfIpv6AdjNodeInvalid	1.3.6.1.4.1.18.3.5.3.16.1.1.7.1.9	INTEGER	read-only	Whether the record passed validation or not
PHY wfIpv6AdjNodePhysicalAddr	1.3.6.1.4.1.18.3.5.3.16.1.1.7.1.5	PhysAddress	read-write	The Physical Address for this Adjacent Node. For FR PVC it is a 32 bit DLCI. For ATM PVC it is a 32 bit VCID which has circuit VCI in its most significant 20 bits and VPI in 12 least significant bits.
INT wfIpv6AdjNodePreference	1.3.6.1.4.1.18.3.5.3.16.1.1.7.1.7	INTEGER	read-write	The Routing Preference in 0 to 15 range. A value of 15 is 'most preferred'. Default 15.
STR wfIpv6AdjNodeWanAddr	1.3.6.1.4.1.18.3.5.3.16.1.1.7.1.10	DisplayString	read-write	WAN address (X.121, E.164, etc.) used to establish an SVC to the adjacent host. For X.25 PVC it contains LCN of the PVC encoded as a X.121 address uo to 4 octets in length.
wfIpv6Base	1.3.6.1.4.1.18.3.5.3.16.1.1.1
INT wfIpv6BaseDefaultHopLimit	1.3.6.1.4.1.18.3.5.3.16.1.1.1.5	INTEGER	read-write	The default value inserted into the 'Hop Limit' field of the IPv6 header of datagrams originated at this entity, whenever a Hop-Limit value is not supplied by the transport layer protocol.
INT wfIpv6BaseDelete	1.3.6.1.4.1.18.3.5.3.16.1.1.1.1	INTEGER	read-write	Create/Delete parameter. Default is created. Users perform a set operation on this object in order to create/delete IPv6.
INT wfIpv6BaseDisable	1.3.6.1.4.1.18.3.5.3.16.1.1.1.2	INTEGER	read-write	Enable/Disable parameter. Default is enabled. Users perform a set operation on this object in order to enable/disable IPv6.
INT wfIpv6BaseForwarding	1.3.6.1.4.1.18.3.5.3.16.1.1.1.4	INTEGER	read-write	The indication of whether this entity is acting as an IPv6 router in respect to the forwarding of datagrams received by, but not addressed to, this entity. IPv6 routers forward datagrams. IPv6 hosts do not (except those source-routed via the host). Note that for some managed nodes, this object may take on only a subset of the values possible. Accordingly, it is appropriate for an agent to return a `badValue' response if a management station attempts to change this object to an inappropriate value.
INT wfIpv6BaseHighestFilterRule	1.3.6.1.4.1.18.3.5.3.16.1.1.1.12	INTEGER	read-write	The highest rule number (wfIpv6FilterNumber) that can be used in a traffic filter definition.
INT wfIpv6BaseIfNumber	1.3.6.1.4.1.18.3.5.3.16.1.1.1.9	INTEGER	read-only	The number of network interfaces (regardless of their current state) present on this system.
INT wfIpv6BaseMinLinkMTU	1.3.6.1.4.1.18.3.5.3.16.1.1.1.6	INTEGER	read-write	This parameter indicates the minimum link MTU that is assumed for every link in the IPv6 internet. IPv6 specification defines this value to be 576 bytes, which is the default value of this attribute. By changing this parameter to other number it is possible to control the maximum size of packets that can be generated by this router if the Path MTU discovery is disabled.
INT wfIpv6BaseMTUDiscovery	1.3.6.1.4.1.18.3.5.3.16.1.1.1.7	INTEGER	read-write	Whether the Path MTU discovery support for self-originated traffic is enabled/disabled
INT wfIpv6BaseMTUTimeout	1.3.6.1.4.1.18.3.5.3.16.1.1.1.8	INTEGER	read-write	Timeout period for discovered Path MTU value in minutes. 0 indicates infinite timeout period, i.e. no timeout.
INT wfIpv6BaseNetworks	1.3.6.1.4.1.18.3.5.3.16.1.1.1.10	INTEGER	read-only	The number of network layer reachability entries in the routing table
INT wfIpv6BaseNodes	1.3.6.1.4.1.18.3.5.3.16.1.1.1.11	INTEGER	read-only	This parameter indicates the number of nodes known by IPv6
INT wfIpv6BaseState	1.3.6.1.4.1.18.3.5.3.16.1.1.1.3	INTEGER	read-only	The current state of the entire IPv6.
INT wfIpv6DbgInfoActiveInterfaces	1.3.6.1.4.1.18.3.5.3.16.1.1.10.1.5	INTEGER	read-only	The number of active IPv6 interface on this slot.
wfIpv6DbgInfoEntry	1.3.6.1.4.1.18.3.5.3.16.1.1.10.1		not-accessible	A description of a IPV6_NDISC interface
INT wfIpv6DbgInfoNetworks	1.3.6.1.4.1.18.3.5.3.16.1.1.10.1.3	INTEGER	read-only	The number of network layer reachability entries in the routing table on this slot
INT wfIpv6DbgInfoNodes	1.3.6.1.4.1.18.3.5.3.16.1.1.10.1.4	INTEGER	read-only	This parameter indicates the number of nodes known by IPv6 on this slot.
GAU wfIpv6DbgInfoRtmAddr	1.3.6.1.4.1.18.3.5.3.16.1.1.10.1.6	Gauge	read-only	Memory address of IPv6 RTM Environment on this slot.
INT wfIpv6DbgInfoSlot	1.3.6.1.4.1.18.3.5.3.16.1.1.10.1.1	INTEGER	read-only	Slot number of this information.
INT wfIpv6DbgInfoState	1.3.6.1.4.1.18.3.5.3.16.1.1.10.1.2	INTEGER	read-only	The current state of IPv6 on this slot.
wfIpv6DbgInfoTable	1.3.6.1.4.1.18.3.5.3.16.1.1.10		not-accessible	The debug info table
INT wfIpv6FilterAction	1.3.6.1.4.1.18.3.5.3.16.1.1.11.1.13	INTEGER	read-write	action. If 'forward(1), packet is to be forwarded; if 'discard(2)', packet is to be discarded
INT wfIpv6FilterDelete	1.3.6.1.4.1.18.3.5.3.16.1.1.11.1.1	INTEGER	read-write	Create/Delete parameter. Default is created. Users perform a set operation on this object in order to create/delete an IPv6 filtering rule.
INT wfIpv6FilterDisable	1.3.6.1.4.1.18.3.5.3.16.1.1.11.1.2	INTEGER	read-write	Enable/Disable parameter. Default is enabled. Users perform a set operation on this object in order to enable/disable an IPv6 filtering rule.
OCT wfIpv6FilterDstAddresses	1.3.6.1.4.1.18.3.5.3.16.1.1.11.1.11	OCTET STRING	read-write	Destination Address identification list. This identifies which packet destination addresses will match this rule. If non-null, the octet string contains one or more 2-tuples of this form: 16 octets: address prefix 1 octet: prefix length An encoding ::0/0 means 'match any address'. A null string also means 'match any address'.
wfIpv6FilterEntry	1.3.6.1.4.1.18.3.5.3.16.1.1.11.1		not-accessible	A filtering rule
INT wfIpv6FilterInIfIndex	1.3.6.1.4.1.18.3.5.3.16.1.1.11.1.8	INTEGER	read-write	Interface index which uniquely identifies the incoming IPv6 interface to which this entry is applicable. An interface identified by a particular value in this object is the same interface as identified by the same value of wfIpv6IfIndex. The index value of 0 means 'match any interface'.
INT wfIpv6FilterLog	1.3.6.1.4.1.18.3.5.3.16.1.1.11.1.14	INTEGER	read-write	Log Action. If 'true(1), a log event is generated when a packet matches this filter rule; if 'false(2)', no logging is done.
STR wfIpv6FilterName	1.3.6.1.4.1.18.3.5.3.16.1.1.11.1.4	DisplayString	read-write	Rule name - user specified name for this filter
INT wfIpv6FilterNumber	1.3.6.1.4.1.18.3.5.3.16.1.1.11.1.3	INTEGER	read-only	Filter rule number
CTR wfIpv6FilterOctets	1.3.6.1.4.1.18.3.5.3.16.1.1.11.1.7	Counter	read-only	The total number of octets in packets received that have matched this rule.
INT wfIpv6FilterOutIfIndex	1.3.6.1.4.1.18.3.5.3.16.1.1.11.1.9	INTEGER	read-write	Interface index which uniquely identifies the outgoing IPv6 interface to which this entry is applicable. An interface identified by a particular value in this object is the same interface as identified by the same value of wfIpv6IfIndex. The index value of 0 means 'match any interface', i.e. all packets that are to be forwarded will match this filter parameter. Note that packet which are addressed to the router itself will not match a filter that has zero as its wfIpv6FilterOutIfIndex value. The index value of -1 means that only packets which are addressed to the router itself match this filter parameter. The index value of -2 means that all packets, forwarded or addressed to the router itself, match this filter parameter.
CTR wfIpv6FilterPackets	1.3.6.1.4.1.18.3.5.3.16.1.1.11.1.6	Counter	read-only	The number of packets received that have matched this rule.
GAU wfIpv6FilterPrecedence	1.3.6.1.4.1.18.3.5.3.16.1.1.11.1.5	Gauge	read-write	Precedence. This is a metric to be used to compare this policy rule to other rules that a given packet may match. A rule with a higher precedence value will be chosen over one with a smaller value. In the case of a tie, the rule index is used (lower wins). Note: if there is multiple filters that a given packet may match, it is advisable for a filter with a higher precedence value to be defined with a lower rule index than a filter with a lower precedence value to improve forwarding performance.
OCT wfIpv6FilterProtocols	1.3.6.1.4.1.18.3.5.3.16.1.1.11.1.12	OCTET STRING	read-write	List of upper layer protocol types (e.g., UDP is 16, TCP is 6, ICMP is 58) of the packet payload. If non-null, the octet string contains one or more 3-tuples of this form: 1 octet: protocol type (zero means 'any protocol') 2 octets: value of the first 16 bits of upper-layer payload (zero means 'any value')* 2 octets: value of the next 16 bits of upper-layer payload (zero means 'any value')* For UDP and TCP protocol the first 16 bits of payload correspond to the source port number and the next 16 bits of payload correspond to the destination port number. *If the protocol type is ICMP(58), the first 2-octets value identifies the ICMP Type and second 2-octets value should be set to 0. A null string also means 'match any protocol'.
OCT wfIpv6FilterSrcAddresses	1.3.6.1.4.1.18.3.5.3.16.1.1.11.1.10	OCTET STRING	read-write	Source Address identification list. This identifies which packet source addresses will match this rule. If non-null, the octet string contains one or more 2-tuples of this form: 16 octets: address prefix 1 octet: prefix length in bits An encoding ::0/0 means 'match any address'. A null string also means 'match any address'.
wfIpv6FilterTable	1.3.6.1.4.1.18.3.5.3.16.1.1.11		not-accessible	IPv6 Traffic Filters
wfIpv6IcmpEntry	1.3.6.1.4.1.18.3.5.3.16.2.1.1		not-accessible	An ICMPv6 statistics entry containing objects at a particular IPv6 interface. Note that a receiving interface is the interface to which a given ICMPv6 message is addressed which may not be necessarily the input interface for the message. Similarly, the sending interface is the interface that sources a given ICMP message which is usually but not necessarily the output interface for the message.
wfIpv6IcmpGroup	1.3.6.1.4.1.18.3.5.3.16.2
INT wfIpv6IcmpIfIndex	1.3.6.1.4.1.18.3.5.3.16.2.1.1.1	INTEGER	read-only	The index value which uniquely identifies the local interface to which this entry's information pertains. The interface identified by a particular value of this index is the same interface as identified by the same value of wfIpv6IfIndex.
CTR wfIpv6IcmpInAdminProhibs	1.3.6.1.4.1.18.3.5.3.16.2.1.1.5	Counter	read-only	Number of ICMP dest unreachable/communication administratively prohibited messages received. Note: may be sent by BFE or another system
CTR wfIpv6IcmpInDestUnreachs	1.3.6.1.4.1.18.3.5.3.16.2.1.1.4	Counter	read-only	The number of ICMP Destination Unreachable messages received.
CTR wfIpv6IcmpInEchoReps	1.3.6.1.4.1.18.3.5.3.16.2.1.1.10	Counter	read-only	The number of ICMP Echo Reply messages received.
CTR wfIpv6IcmpInEchos	1.3.6.1.4.1.18.3.5.3.16.2.1.1.9	Counter	read-only	The number of ICMP Echo (request) messages received.
CTR wfIpv6IcmpInErrors	1.3.6.1.4.1.18.3.5.3.16.2.1.1.3	Counter	read-only	The number of ICMP messages which the entity received but determined as having ICMP-specific errors (bad ICMP checksums, bad length, etc.).
CTR wfIpv6IcmpInGroupMembQueries	1.3.6.1.4.1.18.3.5.3.16.2.1.1.16	Counter	read-only	The number of ICMPv6 Group Membership Query messages received by the interface.
CTR wfIpv6IcmpInGroupMembReductions	1.3.6.1.4.1.18.3.5.3.16.2.1.1.18	Counter	read-only	The number of ICMPv6 Group Membership Reduction messages received by the interface.
CTR wfIpv6IcmpInGroupMembResponses	1.3.6.1.4.1.18.3.5.3.16.2.1.1.17	Counter	read-only	The number of ICMPv6 Group Membership Response messages received by the interface.
CTR wfIpv6IcmpInMsgs	1.3.6.1.4.1.18.3.5.3.16.2.1.1.2	Counter	read-only	The total number of ICMP messages which includes all those counted by wfIpv6IcmpInErrors.
CTR wfIpv6IcmpInNeighborAdvertisements	1.3.6.1.4.1.18.3.5.3.16.2.1.1.14	Counter	read-only	The number of ICMP Neighbor Advertisement messages received.
CTR wfIpv6IcmpInNeighborSolicits	1.3.6.1.4.1.18.3.5.3.16.2.1.1.13	Counter	read-only	The number of ICMP Neighbor Solicit messages received.
CTR wfIpv6IcmpInParmProbs	1.3.6.1.4.1.18.3.5.3.16.2.1.1.7	Counter	read-only	The number of ICMP Parameter Problem messages received.
CTR wfIpv6IcmpInPktTooBigs	1.3.6.1.4.1.18.3.5.3.16.2.1.1.8	Counter	read-only	The number of ICMP Packet Too Big messages received.
CTR wfIpv6IcmpInRedirects	1.3.6.1.4.1.18.3.5.3.16.2.1.1.15	Counter	read-only	The number of Redirect messages received.
CTR wfIpv6IcmpInRouterAdvertisements	1.3.6.1.4.1.18.3.5.3.16.2.1.1.12	Counter	read-only	The number of ICMP Router Advertisement messages received.
CTR wfIpv6IcmpInRouterSolicits	1.3.6.1.4.1.18.3.5.3.16.2.1.1.11	Counter	read-only	The number of ICMP Router Solicit messages received.
CTR wfIpv6IcmpInTimeExcds	1.3.6.1.4.1.18.3.5.3.16.2.1.1.6	Counter	read-only	The number of ICMP Time Exceeded messages received.
CTR wfIpv6IcmpOutAdminProhibs	1.3.6.1.4.1.18.3.5.3.16.2.1.1.22	Counter	read-only	Number of ICMP dest unreachable/communication administratively prohibited messages sent.
CTR wfIpv6IcmpOutDestUnreachs	1.3.6.1.4.1.18.3.5.3.16.2.1.1.21	Counter	read-only	The number of ICMP Destination Unreachable messages sent.
CTR wfIpv6IcmpOutEchoReps	1.3.6.1.4.1.18.3.5.3.16.2.1.1.27	Counter	read-only	The number of ICMP Echo Reply messages sent.
CTR wfIpv6IcmpOutEchos	1.3.6.1.4.1.18.3.5.3.16.2.1.1.26	Counter	read-only	The number of ICMP Echo (request) messages sent.
CTR wfIpv6IcmpOutErrors	1.3.6.1.4.1.18.3.5.3.16.2.1.1.20	Counter	read-only	The number of ICMP messages which this entity did not send due to problems discovered within ICMP such as a lack of buffers. This value should not include errors discovered outside the ICMP layer such as the inability of IPv6 to route the resultant datagram. In some implementations there may be no types of error which contribute to this counter's value.
CTR wfIpv6IcmpOutGroupMembQueries	1.3.6.1.4.1.18.3.5.3.16.2.1.1.33	Counter	read-only	The number of ICMPv6 Group Membership Query messages sent
CTR wfIpv6IcmpOutGroupMembReductions	1.3.6.1.4.1.18.3.5.3.16.2.1.1.35	Counter	read-only	The number of ICMPv6 Group Membership Reduction messages sent
CTR wfIpv6IcmpOutGroupMembResponses	1.3.6.1.4.1.18.3.5.3.16.2.1.1.34	Counter	read-only	The number of ICMPv6 Group Membership Response messages sent
CTR wfIpv6IcmpOutMsgs	1.3.6.1.4.1.18.3.5.3.16.2.1.1.19	Counter	read-only	The total number of ICMP messages which this entity attempted to send. Note that this counter includes all those counted by icmpOutErrors.
CTR wfIpv6IcmpOutNeighborAdvertisements	1.3.6.1.4.1.18.3.5.3.16.2.1.1.31	Counter	read-only	The number of ICMP Neighbor Advertisement messages received.
CTR wfIpv6IcmpOutNeighborSolicits	1.3.6.1.4.1.18.3.5.3.16.2.1.1.30	Counter	read-only	The number of ICMP Neighbor Solicitation messages sent.
CTR wfIpv6IcmpOutParmProbs	1.3.6.1.4.1.18.3.5.3.16.2.1.1.24	Counter	read-only	The number of ICMP Parameter Problem messages sent.
CTR wfIpv6IcmpOutPktTooBigs	1.3.6.1.4.1.18.3.5.3.16.2.1.1.25	Counter	read-only	The number of ICMP Packet Too Big messages sent.
CTR wfIpv6IcmpOutRedirects	1.3.6.1.4.1.18.3.5.3.16.2.1.1.32	Counter	read-only	The number of Redirect messages sent. For a host, this object will always be zero, since hosts do not send redirects.
CTR wfIpv6IcmpOutRouterAdvertisements	1.3.6.1.4.1.18.3.5.3.16.2.1.1.29	Counter	read-only	The number of ICMP Router Advertisement messages received.
CTR wfIpv6IcmpOutRouterSolicits	1.3.6.1.4.1.18.3.5.3.16.2.1.1.28	Counter	read-only	The number of ICMP Router Solicitation messages sent.
CTR wfIpv6IcmpOutTimeExcds	1.3.6.1.4.1.18.3.5.3.16.2.1.1.23	Counter	read-only	The number of ICMP Time Exceeded messages sent.
wfIpv6IcmpTable	1.3.6.1.4.1.18.3.5.3.16.2.1		not-accessible	IPv6 ICMP statistics
INT wfIpv6IfCfgLinkMTU	1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.13	INTEGER	read-write	The configured link MTU. It will be only considered if it is less than the default MTU of the underlying media. A value of zero indicates that the default MTU of the underlying media is to be used.
PHY wfIpv6IfCfgPhysicalAddress	1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.11	PhysAddress	read-write	The desired link layer address set by the user
OCT wfIpv6IfCfgToken	1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.7	OCTET STRING	read-write	The desired identifier (interface token) for this interface that is (at least) unique on the link this interface is attached to. The interface token is combined with an address prefix to form an interface address. If no token value is configured (the token length is zero), the interface token is autoconfigured according to the rules of the link type this interface is attached to.
INT wfIpv6IfCfgTokenLength	1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.8	INTEGER	read-write	The length of the configured interface token in bits.
INT wfIpv6IfCircuit	1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.6	INTEGER	read-write	The Circuit Number that this interface runs over. If Circuit Number is between 1 and 1023, it identifies a subnetwork/datalink layer interface, i.e. the layer below the network layer. A subnetwork layer interface is associated with a physical link or, in some rare cases, with a group of physical links. Generally, more than one subnetwork layer interface can be defined on a physical link (e.g. channels on a T1 link). If the Circuit Number is higher that 1023, it's a circuitless interface, i.e. a logical IPv6 interface that is not associated with any subnetwork layer or physical layer interface. Zero indicates that it's a tunnel endpoint, i.e. IPv6 packets are encapsulated and transmitted by another network layer protocol or another instance of the IPv6 protocol.
INT wfIpv6IfDelete	1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.1	INTEGER	read-write	Create/Delete parameter. Default is created. Users perform a set operation on this object in order to create/delete an IPv6 interface.
STR wfIpv6IfDescr	1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.5	DisplayString	read-write	An optional textual string containing description of the interface.
INT wfIpv6IfDisable	1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.2	INTEGER	read-write	Enable/Disable parameter. Default is enabled. Users perform a set operation on this object in order to enable/disable an IPv6 interface.
wfIpv6IfEntry	1.3.6.1.4.1.18.3.5.3.16.1.1.2.1		not-accessible	An interface entry containing objects at the a particular IPv6 interface.
INT wfIpv6IfFRBcastDlci	1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.23	INTEGER	read-write	Frame Relay broadcast dlci
INT wfIpv6IfFRMcast1Dlci	1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.24	INTEGER	read-write	Frame Relay multicast dlci #1
INT wfIpv6IfFRMcast2Dlci	1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.25	INTEGER	read-write	Frame Relay multicast dlci #2
INT wfIpv6IfFwdCacheSize	1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.14	INTEGER	read-write	Maximum number of entries allowed in the Forwarding (Cache) Table at one time. There is a forwarding table per interface. If this attribute is set to zero, the Forwarding Cache is not used on this interface.
INT wfIpv6IfIcmpErrorLimit	1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.20	INTEGER	read-write	The maximum number of ICMP Error messages that is allowed to be transmitted within 1 second interval out of this interface.
INT wfIpv6IfIndex	1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.4	INTEGER	read-only	A unique non-zero value for each interface.
IP wfIpv6IfIPv4TunnelLocalAddress	1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.27	IpAddress	read-write	If wfIpv6IfCircuit is zero and the tunnel protocol type is IPv4 or ip4sa, this parameter contains the local IPv4 address of this interface's tunnel.
IP wfIpv6IfIPv4TunnelRemoteAddress	1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.28	IpAddress	read-write	If wfIpv6IfCircuit is zero and the tunnel protocol type is IPv4 or ip4sa, this parameter contains the remote IPv4 address of this interface's tunnel. If this address is 0.0.0.0, this is interface to an automatic tunnel, i.e. the destination address of encapsulating header is derived from the destination address of encapsulated packet.
INT wfIpv6IfIpv6TunnelIfIndex	1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.29	INTEGER	read-write	If wfIpv6IfCircuit is zero and the tunnel protocol type is IPv6 or ip6sa, this parameter contains the IPv6 interface index of the local end of this interface's tunnel.
ADR wfIpv6IfIpv6TunnelRemoteAddress	1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.30	Ipv6Address	read-write	If wfIpv6IfCircuit is zero and the tunnel protocol type is IPv6 or ip6sa, this parameter contains the remote IPv6 address of this interface's tunnel. If this address is unspecified (::0), this is interface to an automatic tunnel, i.e. the destination address of encapsulating header is derived from the destination address of encapsulated packet.
TIK wfIpv6IfLastChange	1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.16	TimeTicks	read-only	The time (in hundredths of a second) since the node was last re-initialized at the time the interface entered its current operational state. Usually the time since boot.
INT wfIpv6IfMaxInfo	1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.18	INTEGER	read-only	The maximum size of the INFO (non-MAC) field that this port will receive or transmit (effective MTU size).
PHY wfIpv6IfPhysicalAddress	1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.12	PhysAddress	read-only	The Physical Address for this Interface - actual one used
INT wfIpv6IfReasmMaxSize	1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.17	INTEGER	read-only	The size of the largest IPv6 datagram which this entity can re-assemble from incoming IPv6 fragmented packets received on this interface.
INT wfIpv6IfRedirect	1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.19	INTEGER	read-write	Indicates whether we're sending out redirects on this Interface or not
GAU wfIpv6IfSlotMask	1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.15	Gauge	read-write	Slot mask for which slots a circuit-less interface is eligible to run on. The most significant bit represents slot 1, the next most significant bit represents slot 2, and so on... Slots can be 1-14. This is only valid if wfIpv6IfCircuit is greater than 1023.
OCT wfIpv6IfSMDSGroupAddress	1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.22	OCTET STRING	read-write	The SMDS group address
INT wfIpv6IfState	1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.3	INTEGER	read-only	The current operational state of the interface. Tokenless state indicates the no valid address token is assigned to the interface. This state usually indicates that the link-local interface address failed Duplicate Address Detection. Invalid state indicates an error in processing the cfg record.
CTR wfIpv6IfStatsCacheMisses	1.3.6.1.4.1.18.3.5.3.16.1.1.5.1.16	Counter	read-only	The number of FFT cache misses (i.e how many times did the cache gate have to do a look up in the RNP because the FFT didn't have the destination network
CTR wfIpv6IfStatsCacheNetworks	1.3.6.1.4.1.18.3.5.3.16.1.1.5.1.17	Counter	read-only	The number of network entries in the forwarding cache
CTR wfIpv6IfStatsCacheRemoves	1.3.6.1.4.1.18.3.5.3.16.1.1.5.1.18	Counter	read-only	The number of networks which have been flushed from the forwarding cache
wfIpv6IfStatsEntry	1.3.6.1.4.1.18.3.5.3.16.1.1.5.1		not-accessible	An interface statistics entry containing objects at a particular IPv6 interface.
CTR wfIpv6IfStatsForwDatagrams	1.3.6.1.4.1.18.3.5.3.16.1.1.5.1.10	Counter	read-only	The number of output datagrams which this entity received and forwarded to their final destinations. In entities which do not act as IPv6 routers, this counter will include only those packets which were Source-Routed via this entity, and the Source-Route processing was successful. Note that for a successfully forwarded datagram the counter of the outgoing interface is incremented.
CTR wfIpv6IfStatsFragCreates	1.3.6.1.4.1.18.3.5.3.16.1.1.5.1.15	Counter	read-only	The number of output datagram fragments that have been generated as a result of fragmentation at this output interface.
CTR wfIpv6IfStatsFragFails	1.3.6.1.4.1.18.3.5.3.16.1.1.5.1.14	Counter	read-only	The number of IPv6 datagrams that have been discarded because they needed to be fragmented at this output interface but could not be.
CTR wfIpv6IfStatsFragOKs	1.3.6.1.4.1.18.3.5.3.16.1.1.5.1.13	Counter	read-only	The number of IPv6 datagrams that have been successfully fragmented at this output interface.
INT wfIpv6IfStatsIfIndex	1.3.6.1.4.1.18.3.5.3.16.1.1.5.1.1	INTEGER	read-only	The index value which uniquely identifies the IPv6 interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of wfIpv6IfIndex.
CTR wfIpv6IfStatsInAddrErrors	1.3.6.1.4.1.18.3.5.3.16.1.1.5.1.6	Counter	read-only	The number of input datagrams discarded because the IPv6 address in their IPv6 header's destination field was not a valid address to be received at this entity. This count includes invalid addresses (e.g., ::0) and unsupported addresses (e.g., addresses with unallocated prefixes). For entities which are not IPv6 routers and therefore do not forward datagrams, this counter includes datagrams discarded because the destination address was not a local address.
CTR wfIpv6IfStatsInDelivers	1.3.6.1.4.1.18.3.5.3.16.1.1.5.1.9	Counter	read-only	The total number of input datagrams successfully delivered to IPv6 user-protocols (including ICMP).
CTR wfIpv6IfStatsInDiscards	1.3.6.1.4.1.18.3.5.3.16.1.1.5.1.8	Counter	read-only	The number of input IPv6 datagrams for which no problems were encountered to prevent their continued processing, but which were discarded (e.g., for lack of buffer space). Note that this counter does not include any datagrams discarded while awaiting re-assembly.
CTR wfIpv6IfStatsInHdrErrors	1.3.6.1.4.1.18.3.5.3.16.1.1.5.1.3	Counter	read-only	The number of input datagrams discarded due to errors in their IPv6 headers, including version number mismatch, other format errors, hop count exceeded, errors discovered in processing their IPv6 options, etc.
CTR wfIpv6IfStatsInNoRoutes	1.3.6.1.4.1.18.3.5.3.16.1.1.5.1.5	Counter	read-only	The number of input datagrams discarded because no route could be found to transmit them to their destination.
CTR wfIpv6IfStatsInReceives	1.3.6.1.4.1.18.3.5.3.16.1.1.5.1.2	Counter	read-only	The total number of input datagrams received from interfaces, including those received in error.
CTR wfIpv6IfStatsInTooBigErrors	1.3.6.1.4.1.18.3.5.3.16.1.1.5.1.4	Counter	read-only	The number of input datagrams that could not be forwarded because their size exceeded the link MTU of outgoing interface.
CTR wfIpv6IfStatsInTruncatedPkts	1.3.6.1.4.1.18.3.5.3.16.1.1.5.1.24	Counter	read-only	The number of input datagrams discarded because datagram frame didn't carry enough data
CTR wfIpv6IfStatsInUnknownProtos	1.3.6.1.4.1.18.3.5.3.16.1.1.5.1.7	Counter	read-only	The number of locally-addressed datagrams received successfully but discarded because of an unknown or unsupported protocol.
CTR wfIpv6IfStatsMcastInPkts	1.3.6.1.4.1.18.3.5.3.16.1.1.5.1.22	Counter	read-only	The number of multicast packets received by the interface
CTR wfIpv6IfStatsMcastOutPkts	1.3.6.1.4.1.18.3.5.3.16.1.1.5.1.23	Counter	read-only	The number of multicast packets transmitted by the interface
CTR wfIpv6IfStatsOutDiscards	1.3.6.1.4.1.18.3.5.3.16.1.1.5.1.12	Counter	read-only	The number of output IPv6 datagrams for which no problem was encountered to prevent their transmission to their destination, but which were discarded (e.g., for lack of buffer space). Note that this counter would include datagrams counted in wfIpv6IfStatsForwDatagrams if any such packets met this (discretionary) discard criterion.
CTR wfIpv6IfStatsOutRequests	1.3.6.1.4.1.18.3.5.3.16.1.1.5.1.11	Counter	read-only	The total number of IPv6 datagrams which local IPv6 user-protocols (including ICMP) supplied to IPv6 in requests for transmission. Note that this counter does not include any datagrams counted in wfIpv6IfStatsForwDatagrams.
CTR wfIpv6IfStatsReasmFails	1.3.6.1.4.1.18.3.5.3.16.1.1.5.1.21	Counter	read-only	The number of failures detected by the IPv6 re- assembly algorithm (for whatever reason: timed out, errors, etc). Note that this is not necessarily a count of discarded IPv6 fragments since some algorithms (notably the algorithm in RFC 815) can lose track of the number of fragments by combining them as they are received. This counter is incremented at the interface to which these fragments were addressed which might not be necessarily the input interface for some of the fragments.
CTR wfIpv6IfStatsReasmOKs	1.3.6.1.4.1.18.3.5.3.16.1.1.5.1.20	Counter	read-only	The number of IPv6 datagrams successfully reassembled.
CTR wfIpv6IfStatsReasmReqds	1.3.6.1.4.1.18.3.5.3.16.1.1.5.1.19	Counter	read-only	The number of IPv6 fragments received which needed to be reassembled at this interface. Note that this counter is incremented at the interface to which these fragments were addressed which might not be necessarily the input interface for some of the fragments.
wfIpv6IfStatsTable	1.3.6.1.4.1.18.3.5.3.16.1.1.5		not-accessible	IPv6 interface statistics
wfIpv6IfTable	1.3.6.1.4.1.18.3.5.3.16.1.1.2		not-accessible	The list of IPv6 interface entries. This is the configuration table of logical IPv6 interfaces at the network layer. An IPv6 interface constitutes a logical network layer attachment to a link ('circuit' in the Bay Networks terminology) at the subnetwork/datalink layer, i.e. the layer immediately below the network layer including internet layer 'tunnels', such as tunnels over IPv4 or IPv6 itself. In Bay Network routers a subnetwork link (a.k.a. circuit) is identified with a circuit id. One or more circuits can be configured on a physical link. One or more IPv6 logical interfaces can be configured on a given circuit.
OCT wfIpv6IfToken	1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.9	OCTET STRING	read-only	The actual identifier (interface token) for this interface that is (at least) unique on the link this interface is attached to.
INT wfIpv6IfTokenLength	1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.10	INTEGER	read-only	The length of the interface token in bits.
INT wfIpv6IfTrEndStation	1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.21	INTEGER	read-write	Use Source Routing over token ring selection. Only applies if a token ring interface.
INT wfIpv6IfTunnelProtocol	1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.26	INTEGER	read-write	If wfIpv6IfCircuit is zero, this parameter specifies the tunnel protocol type: ip4st - IPv6-in-IPv4 static tunnel, ip6st - IPv6-in-Ipv6 static tunnel, ip4au - IPv6-in-IPv4 automatic tunnel, ip6au - IPv6-in-Ipv6 automatic tunnel, ip4sa - IPv6-in-Ipv4 semiautomatic tunnel, ip6sa - IPv6-in-Ipv6 semiautomatic tunnel. Static tunnels are tunnels where both local and remote endpoints must be defined. They are also called configured tunnels. Automatic tunnels are tunnels that don't have predefined remote address, i.e. the destination address of encapsulating header is derived from the destination address of encapsulated packet. They also called opened-end tunnels. A semiautomatic tunnel acts as a static tunnel for outgoing traffic and as an automatic (multipoint-to-point) tunnel for incoming traffic. Both local and remote endpoints must be configured.
wfIpv6Log	1.3.6.1.4.1.18.3.5.3.16.5.1
OCT wfIpv6LogCfgEvents	1.3.6.1.4.1.18.3.5.3.16.5.1.7	OCTET STRING	read-write	User-defined vector of enabled debug messages at boot moment. Coded as instance above
INT wfIpv6LogDelete	1.3.6.1.4.1.18.3.5.3.16.5.1.1	INTEGER	read-write	Create/Delete parameter. Default is created. Users perform a set operation on this object in order to create/delete wfIpv6Log mib object.
INT wfIpv6LogDisable	1.3.6.1.4.1.18.3.5.3.16.5.1.2	INTEGER	read-write	Enable/Disable parameter. Default is enabled.
INT wfIpv6LogEvent	1.3.6.1.4.1.18.3.5.3.16.5.1.4	INTEGER	read-write	Indicates whether a log message which corresponds to the value of this attributes should be sent to the log. It affects wfIpv6LogCodes only. In order to save combined list of messages you have to set wfIpv6LogCfgEvents directly as copy of wfIpv6LogEvents.
INT wfIpv6LogEventDisable	1.3.6.1.4.1.18.3.5.3.16.5.1.5	INTEGER	read-write	Indicates whether a log event defined in wfIpv6LogEvent is to be logged.
OCT wfIpv6LogEvents	1.3.6.1.4.1.18.3.5.3.16.5.1.6	OCTET STRING	read-only	Vector of enabled debug messages (to check only). Messages are identified via the string of bits contained within this attribute. The first octet contains bits 0 to 7, the second octet contains bits 8 to 15, and so on, with the most significant bit referring to the lowest bit number in the octet (e.g., the MSB of the first octet refers to bit 0). If a bit, i, is present and set, then the DEBUG log message with the code (i) is enabled.
wfIpv6LogGroup	1.3.6.1.4.1.18.3.5.3.16.5
INT wfIpv6LogLevel	1.3.6.1.4.1.18.3.5.3.16.5.1.3	INTEGER	read-write	BGP log event level. Setting log to a specific level enables logging IPv6 events of this level and higher.
wfIpv6NDiscGroup	1.3.6.1.4.1.18.3.5.3.16.3
INT wfIpv6NdiscIfDefaultLifetime	1.3.6.1.4.1.18.3.5.3.16.3.1.1.13	INTEGER	read-write	The lifetime associated with the default router in units of seconds.
INT wfIpv6NdiscIfDelete	1.3.6.1.4.1.18.3.5.3.16.3.1.1.1	INTEGER	read-write	Create/Delete parameter. Default is created. Users perform a set operation on this object in order to create/delete an IPV6_NDISC Interface instance.
INT wfIpv6NdiscIfDisable	1.3.6.1.4.1.18.3.5.3.16.3.1.1.2	INTEGER	read-write	Enable/Disable parameter. Default is enabled. Users perform a set operation on this object in order to enable/disable a IPV6_NDISC interface.
INT wfIpv6NdiscIfDupAddrDetectTransmits	1.3.6.1.4.1.18.3.5.3.16.3.1.1.14	INTEGER	read-write	The number of consecutive Neighbor Solicitations messages sent while performing Duplicate Address Detection on a tentative address. A value of zero indicates that no Duplicate Address Detection needs to be performed. A value of one indicates a single transmission with no follow up retransmission.
wfIpv6NdiscIfEntry	1.3.6.1.4.1.18.3.5.3.16.3.1.1		not-accessible	A description of a IPV6_NDISC interface
INT wfIpv6NdiscIfIndex	1.3.6.1.4.1.18.3.5.3.16.3.1.1.4	INTEGER	read-only	The index value which uniquely identifies the local interface to which this entry's information pertains. The interface identified by a particular value of this index is the same interface as identified by the same value of wfIpv6IfIndex.
INT wfIpv6NdiscIfManagedFlag	1.3.6.1.4.1.18.3.5.3.16.3.1.1.6	INTEGER	read-write	Managed Address Configuration flag. When set, hosts use the administered (stateful) protocol for address autoconfiguration in addition to any addresses autoconfigured using stateless address autoconfiguration.
INT wfIpv6NdiscIfMaxHopLimit	1.3.6.1.4.1.18.3.5.3.16.3.1.1.10	INTEGER	read-write	Maximum hop limit (network diameter) to advertise
INT wfIpv6NdiscIfMaxRtrAdvInterval	1.3.6.1.4.1.18.3.5.3.16.3.1.1.12	INTEGER	read-write	The maximum time allowed between sending unsolicited multicast Router Advertisements, in seconds.
INT wfIpv6NdiscIfMinRtrAdvInterval	1.3.6.1.4.1.18.3.5.3.16.3.1.1.11	INTEGER	read-write	The minimum time allowed between sending unsolicited multicast Router Advertisements, in seconds.
INT wfIpv6NdiscIfOtherCfgFlag	1.3.6.1.4.1.18.3.5.3.16.3.1.1.7	INTEGER	read-write	Other Stateful Configuration flag. When set, hosts use the administered (stateful) protocol for autoconfiguration of non-address information.
INT wfIpv6NdiscIfReachableTime	1.3.6.1.4.1.18.3.5.3.16.3.1.1.8	INTEGER	read-write	The time, in milliseconds, that a node assumes a neighbor is reachable after having received a reachability confirmation. A value of zero means unspecified (by this router).
INT wfIpv6NdiscIfRetransTimer	1.3.6.1.4.1.18.3.5.3.16.3.1.1.9	INTEGER	read-write	The time, in milliseconds, between retransmitted Neighbor Solicitation messages. A value of zero means unspecified (by this router).
INT wfIpv6NdiscIfSendAdvertisements	1.3.6.1.4.1.18.3.5.3.16.3.1.1.5	INTEGER	read-write	Indicates whether or not periodic Router Advertisements are to be sent.
INT wfIpv6NdiscIfState	1.3.6.1.4.1.18.3.5.3.16.3.1.1.3	INTEGER	read-only	The current state of IPV6_NDISC on this interface.
wfIpv6NdiscIfTable	1.3.6.1.4.1.18.3.5.3.16.3.1		not-accessible	The list of configured Neighbor Discovery (ND) interfaces
wfIpv6NetToMediaEntry	1.3.6.1.4.1.18.3.5.3.16.1.1.9.1		not-accessible	A description of a resolved node
wfIpv6NetToMediaEntryTable	1.3.6.1.4.1.18.3.5.3.16.1.1.9		not-accessible	The IPv6 address translation table contain the IPv6 Address to `physical' address equivalences. Some interfaces do not use translation tables for determining address equivalences; if all interfaces are of this type, then the Address Translation table is empty, i.e., has zero entries.
INT wfIpv6NetToMediaIfIndex	1.3.6.1.4.1.18.3.5.3.16.1.1.9.1.1	INTEGER	read-only	The interface on which this entry's equivalence is effective. The interface identified by a particular value of this index is the same interface as identified by the same value of wfIpv6IfIndex.
INT wfIpv6NetToMediaInvalid	1.3.6.1.4.1.18.3.5.3.16.1.1.9.1.5	INTEGER	read-write	Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the wfIpv6NetToMediaTable. That is, it effectively disassociates the interface identified with said entry from the mapping identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant wfIpv6NetToMediaInvalid object.
ADR wfIpv6NetToMediaNetAddress	1.3.6.1.4.1.18.3.5.3.16.1.1.9.1.2	Ipv6Address	read-only	The IPv6 Address corresponding to the media-dependent `physical' address.
PHY wfIpv6NetToMediaPhysAddress	1.3.6.1.4.1.18.3.5.3.16.1.1.9.1.3	PhysAddress	read-only	The media-dependent `physical' address.
INT wfIpv6NetToMediaType	1.3.6.1.4.1.18.3.5.3.16.1.1.9.1.4	INTEGER	read-only	The type of mapping.
wfIpv6PolicyGroup	1.3.6.1.4.1.18.3.5.3.16.6
GAU wfIpv6RouteAge	1.3.6.1.4.1.18.3.5.3.16.1.1.8.1.9	Gauge	read-only	The number of seconds since this route was last updated or otherwise determined to be correct. Note that no semantics of `too old' can be implied except through knowledge of the routing protocol by which the route was learned.
ADR wfIpv6RouteDest	1.3.6.1.4.1.18.3.5.3.16.1.1.8.1.1	Ipv6Address	read-only	The destination IPv6 address of this route. An entry with a value of ::0 is considered a default route. This object may not take a Multicast address value.
wfIpv6RouteEntry	1.3.6.1.4.1.18.3.5.3.16.1.1.8.1		not-accessible	A routing entry
INT wfIpv6RouteIfIndex	1.3.6.1.4.1.18.3.5.3.16.1.1.8.1.3	INTEGER	read-only	The index value which uniquely identifies the local interface through which the next hop of this route should be reached. The interface identified by a particular value of this index is the same interface as identified by the same value of wfIpv6IfIndex.
INT wfIpv6RouteIndex	1.3.6.1.4.1.18.3.5.3.16.1.1.8.1.4	INTEGER	read-only	The value which uniquely identifies the route among the routes to the same network layer destination
OID wfIpv6RouteInfo	1.3.6.1.4.1.18.3.5.3.16.1.1.8.1.13	OBJECT IDENTIFIER	read-only	A reference to MIB definitions specific to the particular routing protocol which is responsible for this route, as determined by the value specified in the route's wfIpv6RouteProto value. If this information is not present, its value should be set to the OBJECT ID { 0 0 }, which is a syntactically valid object identifier, and any implementation conforming to ASN.1 and the Basic Encoding Rules must be able to generate and recognize this value.
GAU wfIpv6RouteMetric	1.3.6.1.4.1.18.3.5.3.16.1.1.8.1.11	Gauge	read-only	The routing metric for this route. The semantics of this metric are determined by the routing protocol specified in the route's ipv6RouteProtocol value. When this is unknown or not relevant to the protocol indicated by ipv6RouteProtocol, the object value should be set to its maximum value (4,294,967,295).
ADR wfIpv6RouteNextHop	1.3.6.1.4.1.18.3.5.3.16.1.1.8.1.5	Ipv6Address	read-only	On remote routes, the address of the next system en route; Otherwise, ::0
OCT wfIpv6RouteNextHopRDI	1.3.6.1.4.1.18.3.5.3.16.1.1.8.1.10	OCTET STRING	read-only	The Routing Domain ID of the Next Hop. When this is unknown or not relevant to the protocol indicated by ipv6RouteProtocol, it is an octet string of zero size.
INT wfIpv6RoutePfxLength	1.3.6.1.4.1.18.3.5.3.16.1.1.8.1.2	INTEGER	read-only	Indicates the prefix length of the destination address.
INT wfIpv6RoutePolicy	1.3.6.1.4.1.18.3.5.3.16.1.1.8.1.8	INTEGER	read-only	The general set of conditions that would cause the selection of one multipath route (set of next hops for a given destination) is referred to as 'policy'. Unless the mechanism indicated by wfIpv6RouteProtocol specified otherwise, the policy specifier is the Priority field of the IPv6 packet header. The encoding of IPv6 Priority is specified by the following convention: 0 - uncharacterized traffic 1 - 'filler' traffic (e.g., netnews) 2 - unattended data transfer (e.g., email) 3 - reserved 4 - attended bulk transfer (e.g., FTP, NFS) 5 - reserved 6 - interactive traffic (e.g., telnet, X) 7 - internet control traffic (e.g., routing protocols, SNMP) Protocols defining 'policy' otherwise must either define a set of values which are valid for this object or must implement an integer- instanced policy table for which this object's value acts as an index.
INT wfIpv6RouteProtocol	1.3.6.1.4.1.18.3.5.3.16.1.1.8.1.7	INTEGER	read-only	The routing mechanism via which this route was learned.
wfIpv6RouteTable	1.3.6.1.4.1.18.3.5.3.16.1.1.8		not-accessible	IPv6 Routing table
INT wfIpv6RouteType	1.3.6.1.4.1.18.3.5.3.16.1.1.8.1.6	INTEGER	read-only	The type of route. Note that 'direct(3)' refers to a route for which the next hop is the final destination; 'indirect(4)' refers to a route for which the next hop is not the final destination; 'discard(5)' refers to a route indicating that packets to destinations matching this route are to be discarded (sometimes called black-hole route).
GAU wfIpv6RouteWeight	1.3.6.1.4.1.18.3.5.3.16.1.1.8.1.12	Gauge	read-only	The system internal weight value for this route. The semantics of this value are determined by the implementation specific rules. Generally, within routes with the same wfIpv6RoutePolicy value, the lower the weight value the more preferred is the route.
wfIpv6RoutingGeneralGroup	1.3.6.1.4.1.18.3.5.3.16.1.1
wfIpv6RoutingGroup	1.3.6.1.4.1.18.3.5.3.16.1
INT wfIpv6StaticRouteCost	1.3.6.1.4.1.18.3.5.3.16.1.1.6.1.9	INTEGER	read-write	The Cost of this Static Route. (Used as the RIP metric)
INT wfIpv6StaticRouteDelete	1.3.6.1.4.1.18.3.5.3.16.1.1.6.1.1	INTEGER	read-write	Create/Delete parameter. Default is created. Users perform a set operation on this object in order to create/delete the IPv6 Static Route.
INT wfIpv6StaticRouteDisable	1.3.6.1.4.1.18.3.5.3.16.1.1.6.1.2	INTEGER	read-write	Enable/Disable parameter. Default is enabled. Users perform a set operation on this object in order to enable/disable this IPv6 Static Route.
wfIpv6StaticRouteEntry	1.3.6.1.4.1.18.3.5.3.16.1.1.6.1		not-accessible	A static route definition
INT wfIpv6StaticRouteId	1.3.6.1.4.1.18.3.5.3.16.1.1.6.1.4	INTEGER	read-only	The Route Identifier: which numbered route this is to be
INT wfIpv6StaticRouteIfIndex	1.3.6.1.4.1.18.3.5.3.16.1.1.6.1.3	INTEGER	read-only	The index value which uniquely identifies the local IPv6 interface to be used for forwarding to this Next Hop. The interface identified by a particular value of this index is the same interface as identified by the same value of wfIpv6IfIndex. If this parameter is 0, this is a black-hole route, i.e. packets to destinations matching this route are to be discarded.
INT wfIpv6StaticRouteInvalid	1.3.6.1.4.1.18.3.5.3.16.1.1.6.1.10	INTEGER	read-only	Whether this Static Route is valid or not
ADR wfIpv6StaticRouteNextHopAddr	1.3.6.1.4.1.18.3.5.3.16.1.1.6.1.7	Ipv6Address	read-write	The IPv6 Address of the next hop node. This parameter is ignored for black-hole static routes.
ADR wfIpv6StaticRoutePfx	1.3.6.1.4.1.18.3.5.3.16.1.1.6.1.5	Ipv6AddressPrefix	read-write	The destination IPv6 address prefix of this static route
INT wfIpv6StaticRoutePfxLength	1.3.6.1.4.1.18.3.5.3.16.1.1.6.1.6	INTEGER	read-write	The length (in bits) of the address prefix for this static route
INT wfIpv6StaticRoutePreference	1.3.6.1.4.1.18.3.5.3.16.1.1.6.1.8	INTEGER	read-write	The Routing Preference in 0 to 15 range. A value of 15 is 'most preferred'. Default 15.
wfIpv6StaticRouteTable	1.3.6.1.4.1.18.3.5.3.16.1.1.6		not-accessible	The list of static routes
wfIpv6Udp	1.3.6.1.4.1.18.3.5.3.16.4.1
wfIpv6UdpEntry	1.3.6.1.4.1.18.3.5.3.16.4.2.1		not-accessible	Information about a particular current UDP listener.
wfIpv6UdpGroup	1.3.6.1.4.1.18.3.5.3.16.4
CTR wfIpv6UdpInDatagrams	1.3.6.1.4.1.18.3.5.3.16.4.1.1	Counter	read-only	The total number of UDP datagrams delivered to UDP users.
CTR wfIpv6UdpInErrors	1.3.6.1.4.1.18.3.5.3.16.4.1.3	Counter	read-only	The number of received UDP datagrams that could not be delivered for reasons other than the lack of an application at the destination port.
ADR wfIpv6UdpLocalAddress	1.3.6.1.4.1.18.3.5.3.16.4.2.1.2	Ipv6Address	read-only	The local IPv6 address for this UDP listener. In the case of a UDP listener which is willing to accept datagrams for any IPv6 address associated with the interface, the value ::0 is used.
INT wfIpv6UdpLocalIfIndex	1.3.6.1.4.1.18.3.5.3.16.4.2.1.1	INTEGER	read-only	The index value which uniquely identifies the local interface to which this entry's information pertains. The interface identified by a particular value of this index is the same interface as identified by the same value of wfIpv6IfIndex.
INT wfIpv6UdpLocalPort	1.3.6.1.4.1.18.3.5.3.16.4.2.1.3	INTEGER	read-only	The local port value
CTR wfIpv6UdpNoPorts	1.3.6.1.4.1.18.3.5.3.16.4.1.2	Counter	read-only	The total number of received UDP datagrams for which there was no application at the destination port.
CTR wfIpv6UdpOutDatagrams	1.3.6.1.4.1.18.3.5.3.16.4.1.4	Counter	read-only	The total number of UDP datagrams sent from this entity.
wfIpv6UdpTable	1.3.6.1.4.1.18.3.5.3.16.4.2		not-accessible	The UDP listener table contains information about this entity's UDP end-points on which a local application is currently accepting datagrams.

RFC description

IPv6 routing MIB managing IPv6 routing, ICMP, neighbor discovery, UDP, and policy-based forwarding.

Start monitoring Wellfleet/Bay Networks routers running IPv6 (neighbor-discovery/routing-table status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Wellfleet-IPV6-MIB

What Is Wellfleet-IPV6-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description