All MIBs › TIMETRA-SAS-SYSTEM-MIB
Organization: Alcatel
Last Updated: 2007-01-01
Category: Nokia SR OS / Alcatel-Lucent 7750 SR, System Management
Description: Manages Nokia/Alcatel-Lucent 7210 SAS system identity, software, and operational parameters.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is TIMETRA-SAS-SYSTEM-MIB?
This is a Nokia/Alcatel-Lucent proprietary SNMP MIB defining system-level management objects for the 7210/7x50 SAS (Service Access Switch) product line, covering identity, uplink, and general provisioning features specific to the SAS system architecture. It exposes configuration for redundant "uplink A/B" WAN-facing interfaces, including port, IP address, mask, and VLAN bindings, plus a route table and a keepalive ping address used for uplink health checking. It is centrally used to monitor the hardware/software health of the switch's dual-uplink redundancy scheme: which uplink (A or B) is currently active, and whether the configured ping target is reachable, both revealing an uplink failover event or WAN connectivity loss. It works alongside the general TIMETRA-CHASSIS-MIB and standard IF-MIB for full hardware/interface status. It is deployed on Nokia/Alcatel-Lucent 7210 SAS switches used at the network edge, typically in dual-homed access/aggregation topologies. Engineers can download the TIMETRA-SAS-SYSTEM-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in TIMETRA-SAS-SYSTEM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Nokia/Alcatel-Lucent 7210 SAS Service Access Switch
Monitoring Examples
An operator polls sbiUplinkAorB to see which of the two redundant uplinks is currently forwarding traffic, cross-checking sbiUplinkAIpAddr/sbiUplinkAVlan versus sbiUplinkBIpAddr/sbiUplinkBVlan to confirm both paths are correctly provisioned. sbiPingAddress combined with sbiUplinkRouteTable/sbiUplinkRouteEntry is monitored to detect loss of reachability to the upstream gateway, which would trigger an uplink switchover. A sudden change in sbiUplinkAorB during otherwise stable operation is a strong signal of an uplink failure event warranting investigation.
What Can Be Monitored
- active uplink (A vs B)
- uplink IP/VLAN configuration
- uplink route table entries
- ping-based uplink reachability
This MIB depends on
Related MIBs
Imported Objects
From IF-MIB
| InterfaceIndexOrZero |
From INET-ADDRESS-MIB
| InetAddress |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Gauge32 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| DateAndTime | |
| DisplayString | |
| RowPointer | |
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TimeStamp | |
| TruthValue |
From TIMETRA-CHASSIS-MIB
| TmnxLEDState | |
| TmnxSlotNumOrZero | |
| tmnxCardEntry | OBJECT-TYPE |
| tmnxChassisEntry | OBJECT-TYPE |
| tmnxChassisFanEntry | OBJECT-TYPE |
| tmnxChassisIndex | OBJECT-TYPE |
| tmnxChassisNotifyHwIndex | OBJECT-TYPE |
| tmnxChassisPowerSupplyEntry | OBJECT-TYPE |
| tmnxChassisPowerSupplyInputStatus | OBJECT-TYPE |
| tmnxChassisPowerSupplyOutputStatus | OBJECT-TYPE |
| tmnxCpmCardEntry | OBJECT-TYPE |
| tmnxHwClass | OBJECT-TYPE |
| tmnxHwEntry | OBJECT-TYPE |
| tmnxHwID | OBJECT-TYPE |
| tmnxHwName | OBJECT-TYPE |
| tmnxHwOperState | OBJECT-TYPE |
| tmnxHwTemperature | OBJECT-TYPE |
From TIMETRA-GLOBAL-MIB
| timetraSRMIBModules | OBJECT-IDENTITY |
| tmnxSRConfs | OBJECT-IDENTITY |
| tmnxSRNotifyPrefix | OBJECT-IDENTITY |
| tmnxSRObjs | OBJECT-IDENTITY |
| timetraSASConfs | OBJECT-IDENTITY |
| timetraSASModules | OBJECT-IDENTITY |
| timetraSASNotifyPrefix | OBJECT-IDENTITY |
| timetraSASObjs | OBJECT-IDENTITY |
From TIMETRA-TC-MIB
| IpAddressPrefixLength | |
| ServiceOperStatus | |
| TBurstSize | |
| TCIRRate | |
| TItemDescription | |
| TNamedItem | |
| TNamedItemOrEmpty | |
| TPIRRate | |
| TPolicyID | |
| TSysResource | |
| TTcpUdpPort | |
| TmnxActionType | |
| TmnxAdminState | |
| TmnxOperGrpHoldDownTime | |
| TmnxOperGrpHoldUpTime | |
| TmnxOperState | |
| TmnxPortID | |
| TmnxVwmCardType |
How to Use in IPNetwork Monitor
Example using sysOperGrpNumMembers OID:
Select a Nokia/Alcatel-Lucent 7210 SAS Service Access Switch (dual-uplink redundancy/keepalive status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type sysOperGrpNumMembers into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The value of sysOperGrpNumMembers indicates the number of members as part of this operational-group. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Gauge32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| timetraSASysMIBModule | 1.3.6.1.4.1.6527.6.2.1.1.7 | This document is the System SNMP MIB module for the Alcatel 7x50 device. The System MIB module defines SNMP objects to manage and provision system features. Copyright 2003-2014 Alcatel-Lucent. All rights reserved. Reproduction of this document is authorized on the condition that the foregoing copyright notice is included. This SNMP MIB module (Specification) embodies Alcatel's proprietary intellectual property. Alcatel retains all title and ownership in the Specification, including any revisions. Alcatel grants all interested parties a non-exclusive license to use and distribute an unmodified copy of this Specification in connection with management of Alcatel products, and without fee, provided this copyright notice and license appear on all copies. This Specification is supplied `as is', and Alcatel makes no warranty, either express or implied, as to the use, operation, condition, or performance of the Specification. | ||
| tmnxSASSysConformance | 1.3.6.1.4.1.6527.6.2.2.1.3 | |||
| tmnxSASSysCompliances | 1.3.6.1.4.1.6527.6.2.2.1.3.1 | |||
| tmnxSASSysGroups | 1.3.6.1.4.1.6527.6.2.2.1.3.2 | |||
| tmnxSASSysV1v0Group | 1.3.6.1.4.1.6527.6.2.2.1.3.2.1 | sas system group object definition for first release | ||
| tmnxSASSysV2v0Group | 1.3.6.1.4.1.6527.6.2.2.1.3.2.2 | sas system group object definition for 2.0 release | ||
| tmnxSASSysV3v0Group | 1.3.6.1.4.1.6527.6.2.2.1.3.2.3 | sas system group object definition for 3.0 release | ||
| tmnxSASSysV4v0Group | 1.3.6.1.4.1.6527.6.2.2.1.3.2.4 | sas system group object definition for 4.0 release | ||
| tmnxSASSysV5v0Group | 1.3.6.1.4.1.6527.6.2.2.1.3.2.5 | sas system group object definition for 5.0 release | ||
| tmnxSASSysObjsV6v0Group | 1.3.6.1.4.1.6527.6.2.2.1.3.2.6 | sas system group object definition for 5.0 release | ||
| tmnxSASSysQosV5v0Group | 1.3.6.1.4.1.6527.6.2.2.1.3.2.7 | sas system group object definition for 5.0 release | ||
| tmnxSASSysV6v0Group | 1.3.6.1.4.1.6527.6.2.2.1.3.2.8 | sas system group object definition for 6.0 release | ||
| tmnxSASSysConsoleV6v0Group | 1.3.6.1.4.1.6527.6.2.2.1.3.2.9 | sas system group object definition for 6.0 release | ||
| tmnxSASSysResPlcyV6v1Group | 1.3.6.1.4.1.6527.6.2.2.1.3.2.10 | sas system resource policy group object definition for 6.1 release | ||
| tmnxSASSysSecConformance | 1.3.6.1.4.1.6527.6.2.2.1.3.4 | |||
| tmnxSASSysSecGroups | 1.3.6.1.4.1.6527.6.2.2.1.3.4.1 | |||
| tmnxSASSysSecV4v0Group | 1.3.6.1.4.1.6527.6.2.2.1.3.4.1.1 | sas system security group object definition for 4.0 release | ||
| tmnxSASSysSecNotifyV4v0Group | 1.3.6.1.4.1.6527.6.2.2.1.3.4.1.2 | The group of notifications supported in 7210 4.0 release | ||
| tmnxSASChassisGroups | 1.3.6.1.4.1.6527.6.2.2.1.10 | |||
| tmnxSASChassisNotificationV3v0Group | 1.3.6.1.4.1.6527.6.2.2.1.10.1 | The group of notifications supported in 7210 3.0 release | ||
| tmnxSASChassisGroup | 1.3.6.1.4.1.6527.6.2.2.1.10.2 | The group of notifications supported in 7210 5.0 release | ||
| tmnxSASChassisV61Group | 1.3.6.1.4.1.6527.6.2.2.1.10.3 | The group of notifications supported in 7210 6.1 release | ||
| tmnxSASSysObjs | 1.3.6.1.4.1.6527.6.2.2.2.5 | |||
| sysSASBofInfo | 1.3.6.1.4.1.6527.6.2.2.2.5.11 | |||
| NUM sbiUplinkAPort | 1.3.6.1.4.1.6527.6.2.2.2.5.11.1 | InterfaceIndexOrZero | read-write | Primary bof port used for autoconfig. When set to zero 'uplinAport' would be reset |
| IP sbiUplinkAIpAddr | 1.3.6.1.4.1.6527.6.2.2.2.5.11.2 | IpAddress | read-write | Primary bof port ip address |
| ADR sbiUplinkAMask | 1.3.6.1.4.1.6527.6.2.2.2.5.11.3 | IpAddressPrefixLength | read-write | The value of sbiActiveIpMask specifies the mask length of the subnet associated with the IP address of the primary bof port. |
| I32 sbiUplinkAVlan | 1.3.6.1.4.1.6527.6.2.2.2.5.11.5 | Integer32 | read-write | Vlan tag to be used on uplinkA, if set to -1 packets are sent out without vlan tag |
| NUM sbiUplinkBPort | 1.3.6.1.4.1.6527.6.2.2.2.5.11.6 | InterfaceIndexOrZero | read-write | Secondary bof port used for autoconfig. When set to zero 'uplinBport' would be reset |
| IP sbiUplinkBIpAddr | 1.3.6.1.4.1.6527.6.2.2.2.5.11.7 | IpAddress | read-write | Secondary bof port ip address |
| ADR sbiUplinkBMask | 1.3.6.1.4.1.6527.6.2.2.2.5.11.8 | IpAddressPrefixLength | read-write | The value of sbiActiveIpMask specifies the mask length of the subnet associated with the IP address of the bof uplink B port. |
| I32 sbiUplinkBVlan | 1.3.6.1.4.1.6527.6.2.2.2.5.11.10 | Integer32 | read-write | Vlan tag to be used on uplinkB, if set to -1 packets are sent out without vlan tag |
| IP sbiPingAddress | 1.3.6.1.4.1.6527.6.2.2.2.5.11.11 | IpAddress | read-write | IP address to be used for ping-test after booting. This is the last step in the auto-init process |
| sbiUplinkRouteTable | 1.3.6.1.4.1.6527.6.2.2.2.5.11.12 | not-accessible | The sbiUplinkRouteTable contains an entry for each static route configured for the given uplink A or B. These static routes are only used during the system bootup | |
| sbiUplinkRouteEntry | 1.3.6.1.4.1.6527.6.2.2.2.5.11.12.1 | not-accessible | Each row entry contains information about a static route configured for the inband mangement. Entries in this table can be created and deleted via SNMP SET operations to sbiUplinkRouteRowStatus. | |
| U32 sbiUplinkAorB | 1.3.6.1.4.1.6527.6.2.2.2.5.11.12.1.1 | Unsigned32 | not-accessible | If set to 1 this route is for the uplinkA, if it is set to 2 it is for uplinkB |
| IP sbiUplinkRouteDest | 1.3.6.1.4.1.6527.6.2.2.2.5.11.12.1.2 | IpAddress | not-accessible | The value of 'sbiUplinkBofRouteDest' specifies the destination IP address of this static route. |
| ADR sbiUplinkRouteMask | 1.3.6.1.4.1.6527.6.2.2.2.5.11.12.1.3 | IpAddressPrefixLength | not-accessible | The value of sbiUplinkRouteMask specifies the length of the subnet mask associated with the destination IP address of this static route. |
| IP sbiUplinkRouteNextHop | 1.3.6.1.4.1.6527.6.2.2.2.5.11.12.1.4 | IpAddress | read-create | The value of sbiUplinkRouteNextHop specifies the IP address of the next hop for this static route. This IP address should be in the same subnet as the ethernet port on the active CPM. The value of sbiUplinkRouteNextHop must be set to a valid IP address for the row creation to succeed. |
| ROW sbiUplinkRouteRowStatus | 1.3.6.1.4.1.6527.6.2.2.2.5.11.12.1.5 | RowStatus | read-create | sbiUplinkRouteRowStatus controls the creation and deletion of rows in the table. To create a row in this table, set the row status to createAndGo(4)'. The value of sbiUplinkRouteNextHop must also be set to a valid IP address for the row creation to succeed. To delete a row in this table, set the row status to delete(6). |
| NUM sbiNoServicePortOne | 1.3.6.1.4.1.6527.6.2.2.2.5.11.13 | InterfaceIndexOrZero | read-write | The value of sbiNoServicePortOne indicates service traffic on the port identified by this InterfaceIndex is disabled. |
| NUM sbiNoServicePortTwo | 1.3.6.1.4.1.6527.6.2.2.2.5.11.14 | InterfaceIndexOrZero | read-write | The value of sbiNoServicePortTwo indicates service traffic on the port identified by this InterfaceIndex is disabled. |
| INT sbiUplinkAdminMode | 1.3.6.1.4.1.6527.6.2.2.2.5.11.15 | INTEGER | read-write | sbiUplinkAdminMode when set to access-uplink, bof uplink would be used in l2 mode,the default mode is network |
| INT sbiUplinkOperMode | 1.3.6.1.4.1.6527.6.2.2.2.5.11.16 | INTEGER | read-only | sbiUplinkOperMode is operational mode of the system. This object is initialized during system bootup based on sbiUplinkAdminMode setting |
| INT sbiExpansionCardType | 1.3.6.1.4.1.6527.6.2.2.2.5.11.17 | INTEGER | read-write | sbiExpansionCardType identifies the expansion card type to the system before boot up. The system will not allow for provisioning of a different MDA than the one currently specified in the BOF. Changes to sbiExpansionCardType equires a reboot to take effect |
| T/F sbiConsoleDisabled | 1.3.6.1.4.1.6527.6.2.2.2.5.11.18 | TruthValue | read-write | The value of sbiConsoleDisabled determines whether or not the system console is disabled. When set to 'true' console is disabled. |
| OCT sbiPassword | 1.3.6.1.4.1.6527.6.2.2.2.5.11.19 | OCTET STRING | read-write | sbiPassword is used to enable the user to configure the bof password. |
| T/F sbiUplinkAAutoNegotiate | 1.3.6.1.4.1.6527.6.2.2.2.5.11.20 | TruthValue | read-write | The value of sbiUplinkAAutoNegotiate determines whether or not the speed and duplex parameters will be automatically negotiated on the uplinkAport. When set to 'true', auto-negotiation is enabled. |
| U32 sbiUplinkASpeed | 1.3.6.1.4.1.6527.6.2.2.2.5.11.21 | Unsigned32 | read-write | The value of sbiSpeed specifies the speed of the uplinkA port. This value is ignored if auto-negotiation is enabled. |
| INT sbiUplinkADuplex | 1.3.6.1.4.1.6527.6.2.2.2.5.11.22 | INTEGER | read-write | The value of sbiDuplex specifies the duplex mode for the uplinkA port. This value is ignored if auto-negotiation is enabled. |
| T/F sbiUplinkBAutoNegotiate | 1.3.6.1.4.1.6527.6.2.2.2.5.11.23 | TruthValue | read-write | The value of sbiUplinkBAutoNegotiate determines whether or not the speed and duplex parameters will be automatically negotiated on the uplinkBport. When set to 'true', auto-negotiation is enabled. |
| U32 sbiUplinkBSpeed | 1.3.6.1.4.1.6527.6.2.2.2.5.11.24 | Unsigned32 | read-write | The value of sbiSpeed specifies the speed of the uplinkB port. This value is ignored if auto-negotiation is enabled. |
| INT sbiUplinkBDuplex | 1.3.6.1.4.1.6527.6.2.2.2.5.11.25 | INTEGER | read-write | The value of sbiDuplex specifies the duplex mode for the uplinkB port. This value is ignored if auto-negotiation is enabled. |
| sysEthMgmtBofInfo | 1.3.6.1.4.1.6527.6.2.2.2.5.12 | |||
| T/F sbiEthMgmtDisabled | 1.3.6.1.4.1.6527.6.2.2.2.5.12.1 | TruthValue | read-write | The value of sbiEthMgmtDisabled determines whether or not the out of band ethernet management port is enabled. When set to 'true', out of band ethernet management port is disabled. |
| IP sbiEthMgmtActiveIpAddr | 1.3.6.1.4.1.6527.6.2.2.2.5.12.2 | IpAddress | read-write | The value of sbiEthMgmtActiveIpAddr specifies the IP address of the out of band ethernet port. |
| ADR sbiEthMgmtActiveIpMask | 1.3.6.1.4.1.6527.6.2.2.2.5.12.3 | IpAddressPrefixLength | read-write | The value of sbiEthMgmtActiveIpMask specifies the mask length of the subnet associated with the IP address of the out of band ethernet port. |
| T/F sbiEthMgmtAutoNegotiate | 1.3.6.1.4.1.6527.6.2.2.2.5.12.4 | TruthValue | read-write | The value of sbiEthMgmtAutoNegotiate determines whether or not the speed and duplex parameters will be automatically negotiated on the out of band ethernet port. |
| U32 sbiEthMgmtSpeed | 1.3.6.1.4.1.6527.6.2.2.2.5.12.5 | Unsigned32 | read-write | The value of sbiEthMgmtSpeed specifies the speed of the out of band ethernet port. This value is ignored if auto-negotiation is enabled. |
| INT sbiEthMgmtDuplex | 1.3.6.1.4.1.6527.6.2.2.2.5.12.6 | INTEGER | read-write | The value of sbiEthMgmtDuplex specifies the duplex mode for the out of band ethernet port. This value is ignored if auto-negotiation is enabled. |
| sbiEthMgmtStaticRouteTable | 1.3.6.1.4.1.6527.6.2.2.2.5.12.7 | not-accessible | The sbiEthMgmtStaticRouteTable contains an entry for each static route configured for the out of band ethernet port. These static routes are only used to route traffic generated by the out of band ethernet port.The table can have upto a maximum of 10 entries. | |
| sbiEthMgmtStaticRouteEntry | 1.3.6.1.4.1.6527.6.2.2.2.5.12.7.1 | not-accessible | Each row entry contains information about a static route configured for the out of band ethernet port. Entries in this table can be created and deleted via SNMP SET operations to sbiEthMgmtStaticRouteRowStatus. | |
| IP sbiEthMgmtStaticRouteDest | 1.3.6.1.4.1.6527.6.2.2.2.5.12.7.1.1 | IpAddress | not-accessible | The value of sbiEthMgmtStaticRouteDest specifies the destination IP address of this static route. |
| ADR sbiEthMgmtStaticRouteMask | 1.3.6.1.4.1.6527.6.2.2.2.5.12.7.1.2 | IpAddressPrefixLength | not-accessible | The value of sbiEthMgmtStaticRouteMask specifies the length of the subnet mask associated with the destination IP address of this static route. |
| IP sbiEthMgmtStaticRouteNextHop | 1.3.6.1.4.1.6527.6.2.2.2.5.12.7.1.3 | IpAddress | read-create | The value of sbiEthMgmtStaticRouteNextHop specifies the IP address of the next hop for this static route. This IP address should be in the same subnet as the ethernet port on the active CPM. The value of sbiEthMgmtStaticRouteNextHop must be set to a valid IP address for the row creation to succeed. |
| ROW sbiEthMgmtStaticRouteRowStatus | 1.3.6.1.4.1.6527.6.2.2.2.5.12.7.1.4 | RowStatus | read-create | sbiEthMgmtStaticRouteRowStatus controls the creation and deletion of rows in the table. To create a row in this table, set the row status to createAndGo(4)'. The value of sbiEthMgmtStaticRouteNextHop must also be set to a valid IP address for the row creation to succeed. To delete a row in this table, set the row status to delete(6). |
| sysMpointMgmtInfo | 1.3.6.1.4.1.6527.6.2.2.2.5.15 | |||
| TNA tSASMpointBwPlcy | 1.3.6.1.4.1.6527.6.2.2.2.5.15.1 | TNamedItem | read-write | The value of multipoint bandwidth management policy. |
| sysLoopBackInfo | 1.3.6.1.4.1.6527.6.2.2.2.5.16 | |||
| TMN sysLoopbackNoServPort | 1.3.6.1.4.1.6527.6.2.2.2.5.16.1 | TmnxPortID | read-write | Second loopback port used for internal sap creation |
| TMN sysMirrorLoopbackNoServPort | 1.3.6.1.4.1.6527.6.2.2.2.5.16.2 | TmnxPortID | read-write | Loopback port for mirroring |
| TMN sysTestHdNoServPort | 1.3.6.1.4.1.6527.6.2.2.2.5.16.3 | TmnxPortID | read-write | Loopback port for testhead |
| sysResourceProfInfo | 1.3.6.1.4.1.6527.6.2.2.2.5.17 | |||
| T/F sysG8032FastFloodEnable | 1.3.6.1.4.1.6527.6.2.2.2.5.17.1 | TruthValue | read-write | Enable disable G.8032 fast flood enable |
| TSY sysResIngTcamSapIngAcl | 1.3.6.1.4.1.6527.6.2.2.2.5.17.2 | TSysResource | read-write | sysResIngTcamSapIngAcl sets the resource to be used for Sap Ingress Acl application |
| TSY sysResIngTcamIngAclMac | 1.3.6.1.4.1.6527.6.2.2.2.5.17.3 | TSysResource | read-write | sysResIngTcamIngAclMac sets the resource to be used for mac match from the allocated sysResIngTcamSapIngAcl |
| TSY sysResIngTcamIngAclIpv4 | 1.3.6.1.4.1.6527.6.2.2.2.5.17.4 | TSysResource | read-write | sysResIngTcamIngAclIpv4 sets the resource to be used for ipv4 match from the allocated sysResIngTcamSapIngAcl |
| TSY sysResIngTcamIngAcl64bitIpv4Ipv6 | 1.3.6.1.4.1.6527.6.2.2.2.5.17.5 | TSysResource | read-write | sysResIngTcamIngAcl64bitIpv4 sets the resource to be used for ipv6 64 bit match from the allocated sysResIngTcamSapIngAcl |
| TSY sysResIngTcamIngAcl128bitIpv4Ipv6 | 1.3.6.1.4.1.6527.6.2.2.2.5.17.6 | TSysResource | read-write | sysResIngTcamIngAcl128bitIpv4Ipv6 sets the resource to be used for ipv6 128 bit match from the allocated sysResIngTcamSapIngAcl |
| TSY sysResIngTcamIngAcl64bitIpv6Only | 1.3.6.1.4.1.6527.6.2.2.2.5.17.7 | TSysResource | read-write | sysResIngTcamIngAcl64bitIpv6Only sets the resource to be used for Ipv6 64 bit match only from the allocated sysResIngTcamSapIngAcl |
| TSY sysResIngSapIngClass | 1.3.6.1.4.1.6527.6.2.2.2.5.17.8 | TSysResource | read-write | sysResIngSapIngClass sets the resource to be used for Sap Ingress classification |
| TSY sysResIngSapIngClassMac | 1.3.6.1.4.1.6527.6.2.2.2.5.17.9 | TSysResource | read-write | sysResIngSapIngClassMac sets the resource to be used for mac match from the allocated sysResIngSapIngClass |
| TSY sysResIngSapIngClassIpv4 | 1.3.6.1.4.1.6527.6.2.2.2.5.17.10 | TSysResource | read-write | sysResIngSapIngClassIpv4 sets the resource to be used for ipv4 match from the allocated sysResIngSapIngClass |
| TSY sysResIngSapIngClassIpv4Ipv6 | 1.3.6.1.4.1.6527.6.2.2.2.5.17.11 | TSysResource | read-write | sysResIngSapIngClassIpv4Ipv4Ipv6 sets the resource to be used for ipv4, ipv6 match from the allocated sysResIngSapIngClass |
| INT sysResFabricPathBandwidth | 1.3.6.1.4.1.6527.6.2.2.2.5.17.12 | INTEGER | read-write | This object is used to configure the system fabric path bandwidth |
| I32 sysResMaxIPv6Routes | 1.3.6.1.4.1.6527.6.2.2.2.5.17.13 | Integer32 | read-create | Specifies the number of routes to be reserved for use by IPv6. If the value is -1, then there is no limit. |
| TSY sysResIngTcamEthCfm | 1.3.6.1.4.1.6527.6.2.2.2.5.17.14 | TSysResource | read-write | sysResIngTcamEthCfm sets the resource to be used for Eth Cfm application |
| TSY sysResIngTcamEthCfmUpMep | 1.3.6.1.4.1.6527.6.2.2.2.5.17.15 | TSysResource | read-write | sysResIngTcamEthCfmUpMep sets the resource to be used for Up MEP from the allocated sysResIngTcamEthCfm |
| T/F sysG8032FastFloodEnableOperVal | 1.3.6.1.4.1.6527.6.2.2.2.5.17.16 | TruthValue | read-only | Shows current active value of sysG8032FastFloodEnable |
| TSY sysResEgrTcamSapEgrAcl | 1.3.6.1.4.1.6527.6.2.2.2.5.17.17 | TSysResource | read-write | sysResEgrTcamSapEgrAcl sets the resource to be used for Sap Egress Acl application |
| TSY sysResEgrTcamEgrAclMac | 1.3.6.1.4.1.6527.6.2.2.2.5.17.18 | TSysResource | read-write | sysResEgrTcamEgrAclMac sets the resource to be used for mac match from the allocated sysResEgrTcamSapEgrAcl |
| TSY sysResEgrTcamEgrAclIpv4 | 1.3.6.1.4.1.6527.6.2.2.2.5.17.19 | TSysResource | read-write | sysResEgrTcamEgrAclIpv4 sets the resource to be used for ipv4 match from the allocated sysResEgrTcamSapEgrAcl |
| TSY sysResEgrTcamEgrAcl64bitIpv4Ipv6 | 1.3.6.1.4.1.6527.6.2.2.2.5.17.20 | TSysResource | read-write | sysResEgrTcamEgrAcl64bitIpv4 sets the resource to be used for ipv6 64 bit match from the allocated sysResEgrTcamSapEgrAcl |
| TSY sysResEgrTcamEgrAcl128bitIpv4Ipv6 | 1.3.6.1.4.1.6527.6.2.2.2.5.17.21 | TSysResource | read-write | sysResEgrTcamEgrAcl128bitIpv4Ipv6 sets the resource to be used for ipv6 128 bit match from the allocated sysResEgrTcamSapEgrAcl |
| TSY sysResEgrTcamEgrAcl64bitIpv6Only | 1.3.6.1.4.1.6527.6.2.2.2.5.17.22 | TSysResource | read-write | sysResEgrTcamEgrAcl64bitIpv6Only sets the resource to be used for Ipv6 64 bit match only from the allocated sysResEgrTcamSapEgrAcl |
| TSY sysResEgrSapEgrClass | 1.3.6.1.4.1.6527.6.2.2.2.5.17.23 | TSysResource | read-write | sysResEgrSapEgrClass sets the resource to be used for Sap Egress classification |
| TSY sysResEgrSapEgrClassMac | 1.3.6.1.4.1.6527.6.2.2.2.5.17.24 | TSysResource | read-write | sysResEgrSapEgrClassMac sets the resource to be used for mac match from the allocated sysResEgrSapEgrClass |
| TSY sysResEgrSapEgrClassIpv4 | 1.3.6.1.4.1.6527.6.2.2.2.5.17.25 | TSysResource | read-write | sysResEgrSapEgrClassIpv4 sets the resource to be used for ipv4 match from the allocated sysResEgrSapEgrClass |
| TSY sysResEgrSapEgrClassIpv4Ipv6 | 1.3.6.1.4.1.6527.6.2.2.2.5.17.26 | TSysResource | read-write | sysResEgrSapEgrClassIpv4Ipv4Ipv6 sets the resource to be used for ipv4, ipv6 match from the allocated sysResEgrSapEgrClass |
| TSY sysResIngTcamSapAggMeter | 1.3.6.1.4.1.6527.6.2.2.2.5.17.27 | TSysResource | read-write | sysResIngTcamSapAggMeter sets the resource to be used for sap-aggregate-meters |
| TSY sysResIngTcamSapAggMeterOperVal | 1.3.6.1.4.1.6527.6.2.2.2.5.17.28 | TSysResource | read-only | This object shows the operational value of sysResIngTcamSapAggMeter |
| T/F sysResQosSapIngQMode | 1.3.6.1.4.1.6527.6.2.2.2.5.17.29 | TruthValue | read-write | This object allows the user to switch between the current mode and 22Gig mode. |
| T/F sysResQosSapIngQOperMode | 1.3.6.1.4.1.6527.6.2.2.2.5.17.30 | TruthValue | read-only | This object returns the current operational value of sysResQosSapIngQMode |
| I32 sysResRouterEcmpMaxRoutesDst | 1.3.6.1.4.1.6527.6.2.2.2.5.17.31 | Integer32 | read-create | Specifies the number of routes to be reserved for use by ECMP. |
| T/F sysDhcpSnoopingSdpEnable | 1.3.6.1.4.1.6527.6.2.2.2.5.17.32 | TruthValue | read-write | Enable/disable dhcp snooping on SDPs |
| T/F sysDhcpSnoopingEnable | 1.3.6.1.4.1.6527.6.2.2.2.5.17.33 | TruthValue | read-write | Enable/disable dhcp snooping on the system. Currently for STU only. |
| I32 sysResRouterEcmpMaxRoutesDstOperVal | 1.3.6.1.4.1.6527.6.2.2.2.5.17.34 | Integer32 | read-only | Specifies the operational value of number of routes to be reserved for use by ECMP. |
| INT sysResIpMacMatchEnable | 1.3.6.1.4.1.6527.6.2.2.2.5.17.35 | INTEGER | read-create | Resource allocation for ip mac match enable |
| INT sysG8032FastFlood | 1.3.6.1.4.1.6527.6.2.2.2.5.17.40 | INTEGER | read-write | sysG8032FastFlood sets max-slices of 1 to 5 |
| TSY sysResIngTcamEthCfmDownMep | 1.3.6.1.4.1.6527.6.2.2.2.5.17.51 | TSysResource | read-write | sysResIngTcamEthCfmDownMep sets the resource to be used for Down MEP from the allocated sysResIngTcamEthCfm |
| INT sysResQosMbsPool | 1.3.6.1.4.1.6527.6.2.2.2.5.17.53 | INTEGER | read-write | This object allows the user to set buffer allocation at node or port level. 'node' means no change in the buffer allocation and works without any decommission ports. 'port' means buffers will be divided and shared across ports. In absence of decommission, buffers will be equally divided. If decommission entries are present, the division will happen as per decommission logic. Refer to tResDecommTable |
| INT sysResIngTcamEthCfmUpMepPrimaryVlan | 1.3.6.1.4.1.6527.6.2.2.2.5.17.54 | INTEGER | read-write | sysResIngTcamEthCfmUpMepPrimaryVlan sets max-slices of 0 to 8 |
| INT sysResIngTcamEthCfmDownMepPrimaryVlan | 1.3.6.1.4.1.6527.6.2.2.2.5.17.55 | INTEGER | read-write | sysResIngTcamEthCfmDownMepPrimaryVlan sets max-slices of 0 to 8 |
| I32 sysResRouterMaxIPSubnets | 1.3.6.1.4.1.6527.6.2.2.2.5.17.56 | Integer32 | read-create | Specifies the number of subnets to be reserved for IP. |
| T/F sysQosPortSchedModeEnable | 1.3.6.1.4.1.6527.6.2.2.2.5.17.57 | TruthValue | read-write | Enable disable qos port scheduler mode |
| I32 sysResMaxIPv6RoutesOperVal | 1.3.6.1.4.1.6527.6.2.2.2.5.17.58 | Integer32 | read-only | Specifies the number of routes to be reserved for use by IPv6. If the value is -1, then there is no limit. |
| sysSASObjs | 1.3.6.1.4.1.6527.6.2.2.2.5.18 | |||
| T/F tmnxSysConsoleAlarmInput | 1.3.6.1.4.1.6527.6.2.2.2.5.18.2 | TruthValue | read-write | Enable/Disable Console Alarm Input |
| sysSASVwmObjs | 1.3.6.1.4.1.6527.6.2.2.2.5.19 | |||
| tmnxVwmShelfTable | 1.3.6.1.4.1.6527.6.2.2.2.5.19.1 | not-accessible | The tmnxVwmShelfTable contains an entry for each VWM shelf in the device | |
| tmnxVwmShelfEntry | 1.3.6.1.4.1.6527.6.2.2.2.5.19.1.1 | not-accessible | Each row entry contains information about a VWM shelf Entries in this table can be created and deleted via SNMP SET operations to tmnxVwmShelfRowStatus. | |
| INT tmnxVwmShelfId | 1.3.6.1.4.1.6527.6.2.2.2.5.19.1.1.1 | INTEGER | accessible-for-notify | Shelf ID of the VWM Shelf |
| ROW tmnxVwmShelfRowStatus | 1.3.6.1.4.1.6527.6.2.2.2.5.19.1.1.2 | RowStatus | read-create | tmnxVwmShelfRowStatus controls the creation and deletion of rows in the table. To create a row in this table, set the row status to createAndGo(4)'. |
| TMN tmnxVwmShelfAdminState | 1.3.6.1.4.1.6527.6.2.2.2.5.19.1.1.3 | TmnxAdminState | read-create | The value of tmnxVwmShelfAdminState specifies the administrative state of the VWM shelf. |
| TMN tmnxVwmShelfOperState | 1.3.6.1.4.1.6527.6.2.2.2.5.19.1.1.4 | TmnxAdminState | read-only | The value of tmnxVwmShelfOperState specifies the operational state of the VWM shelf. |
| INT tmnxVwmShelfVwmType | 1.3.6.1.4.1.6527.6.2.2.2.5.19.1.1.5 | INTEGER | read-create | The value of tmnxVwmShelfVwmType specifies the vwm shelf type. |
| INT tmnxVwmShelfEquippedType | 1.3.6.1.4.1.6527.6.2.2.2.5.19.1.1.6 | INTEGER | read-only | The value of tmnxVwmshelfTypeConnected specifies the vwm shelf type.equipped to the system. |
| INT tmnxVwmshelfTypeConnected | 1.3.6.1.4.1.6527.6.2.2.2.5.19.1.1.7 | INTEGER | read-only | The value of tmnxVwmshelfTypeConnected specifies the vwm shelf optical type.connected to the system. |
| tmnxVwmShelfCardTable | 1.3.6.1.4.1.6527.6.2.2.2.5.19.2 | not-accessible | The tmnxVwmShelfCardTable contains an entry for each VWM shelf slot in the device | |
| tmnxVwmShelfCardEntry | 1.3.6.1.4.1.6527.6.2.2.2.5.19.2.1 | not-accessible | Each row entry contains information about a VWM shelf slot Entries in this table can be created and deleted via SNMP SET operations to tmnxVwmShelfRowStatus. | |
| INT tmnxVwmShelfCardId | 1.3.6.1.4.1.6527.6.2.2.2.5.19.2.1.1 | INTEGER | accessible-for-notify | Slot ID of the VWM Shelf slot |
| TMN tmnxVwmShelfCardType | 1.3.6.1.4.1.6527.6.2.2.2.5.19.2.1.2 | TmnxVwmCardType | read-write | tmnxVwmShelfCardType is the vwm slot type that is being configured by user |
| TMN tmnxVwmShelfCardEqType | 1.3.6.1.4.1.6527.6.2.2.2.5.19.2.1.3 | TmnxVwmCardType | read-only | tmnxVwmShelfCardEqType is the vwm slot type that is being provisioned |
| TMN tmnxVwmShelfCardAdminState | 1.3.6.1.4.1.6527.6.2.2.2.5.19.2.1.4 | TmnxAdminState | read-write | The value of tmnxVwmShelfCardAdminState specifies the administrative state of the VWM shelf slot. |
| TMN tmnxVwmShelfCardOperState | 1.3.6.1.4.1.6527.6.2.2.2.5.19.2.1.5 | TmnxAdminState | read-only | The value of tmnxVwmShelfCardOperState specifies the operational state of the VWM shelf slot. |
| sysQosObjs | 1.3.6.1.4.1.6527.6.2.2.2.5.20 | |||
| INT sysQosWredSlopes | 1.3.6.1.4.1.6527.6.2.2.2.5.20.1 | INTEGER | read-write | When tcp-non-tcp is set, 3 WRED slopes are used per queue. When high-low is set, 2 slopes are used per queue for both tcp and non-tcp traffic |
| sysClockInfo | 1.3.6.1.4.1.6527.6.2.2.2.5.21 | |||
| TMN tmnxPtpTimeUsePtp | 1.3.6.1.4.1.6527.6.2.2.2.5.21.1 | TmnxPtpTime | read-write | If this object is configured with 'system', ptp derived time (in UTC timescale) is used for all the system applications that need time, including the timestamps needed for OAM tools. If configured with 'oam', the system will use the PTP derived time (in UTC timescale) for only the timestamps needed by OAM. By default NTP derived time is used for all system applications. If NTP is not configured, then the system RTC is used for obtaining timestmaps in UTC timescale for all system applications |
| sysResProfPlcyObjs | 1.3.6.1.4.1.6527.6.2.2.2.5.22 | |||
| tResPlcyTable | 1.3.6.1.4.1.6527.6.2.2.2.5.22.1 | not-accessible | The tResPlcyTable has an entry for each user configured system resource policy. | |
| tResPlcyEntry | 1.3.6.1.4.1.6527.6.2.2.2.5.22.1.1 | not-accessible | An entry in this table would be created for every resource policy creation | |
| INT tResPlcyId | 1.3.6.1.4.1.6527.6.2.2.2.5.22.1.1.1 | INTEGER | not-accessible | system resource policy id |
| ROW tResPlcyRowStatus | 1.3.6.1.4.1.6527.6.2.2.2.5.22.1.1.2 | RowStatus | read-create | RowStatus of this policy entry |
| INT tResPlcyIngTcamSapAggMeter | 1.3.6.1.4.1.6527.6.2.2.2.5.22.1.1.3 | INTEGER | read-create | Ingress tcam sap aggregate meter resource |
| INT tResPlcyIngTcamQosSapIng | 1.3.6.1.4.1.6527.6.2.2.2.5.22.1.1.4 | INTEGER | read-create | Ingress tcam sap sap ingress resource |
| INT tResPlcyIngTcamQosSapIngIpv4 | 1.3.6.1.4.1.6527.6.2.2.2.5.22.1.1.5 | INTEGER | read-create | Ingress tcam sap ingress ipv4 resource |
| INT tResPlcyIngTcamQosSapIngIpv4Ipv6 | 1.3.6.1.4.1.6527.6.2.2.2.5.22.1.1.6 | INTEGER | read-create | Ingress tcam sap ingress ipv4, ipv6 resource |
| INT tResPlcyIngTcamQosSapIngMac | 1.3.6.1.4.1.6527.6.2.2.2.5.22.1.1.7 | INTEGER | read-create | Ingress tcam sap ingress mac resource |
| INT tResPlcyIngTcamAclSapIng | 1.3.6.1.4.1.6527.6.2.2.2.5.22.1.1.8 | INTEGER | read-create | Ingress tcam acl sap ingress resource |
| INT tResPlcyIngTcamAclSapIngIpv4 | 1.3.6.1.4.1.6527.6.2.2.2.5.22.1.1.9 | INTEGER | read-create | Ingress tcam acl sap ingress ipv4 resource |
| INT tResPlcyIngTcamAclSapIng64Ipv6 | 1.3.6.1.4.1.6527.6.2.2.2.5.22.1.1.10 | INTEGER | read-create | Ingress tcam acl sap ingress 64 bit ipv6 match resource |
| INT tResPlcyIngTcamAclSapIng128Ipv4Ipv6 | 1.3.6.1.4.1.6527.6.2.2.2.5.22.1.1.11 | INTEGER | read-create | Ingress tcam acl sap ingress 128 bit ipv6 resource |
| INT tResPlcyIngTcamAclSapIngMac | 1.3.6.1.4.1.6527.6.2.2.2.5.22.1.1.12 | INTEGER | read-create | Ingress tcam acl sap ingress mac resource |
| INT tResPlcyEgrTcamAclSapEgr | 1.3.6.1.4.1.6527.6.2.2.2.5.22.1.1.13 | INTEGER | read-create | Egress tcam acl sap sap egress 1resource |
| INT tResPlcyEgrTcamAclSapEgrMacIpv4 | 1.3.6.1.4.1.6527.6.2.2.2.5.22.1.1.14 | INTEGER | read-create | Egress tcam acl sap egress mac ipv4 resource |
| INT tResPlcyEgrTcamAclSapEgr128Ipv6 | 1.3.6.1.4.1.6527.6.2.2.2.5.22.1.1.15 | INTEGER | read-create | Egress tcam acl sap egress 128bit ipv6 resource |
| INT tResPlcyEgrTcamAclSapEgr64MacIpv6 | 1.3.6.1.4.1.6527.6.2.2.2.5.22.1.1.16 | INTEGER | read-create | Egress tcam acl sap egress mac resource |
| INT tResPlcyEgrTcamAclSapEgrMac | 1.3.6.1.4.1.6527.6.2.2.2.5.22.1.1.17 | INTEGER | read-create | Egress tcam acl sap egress mac resource |
| TIT tResPlcyDescription | 1.3.6.1.4.1.6527.6.2.2.2.5.22.1.1.18 | TItemDescription | read-create | user-provided description of the policy. |
| TIM tResPlcyLastChanged | 1.3.6.1.4.1.6527.6.2.2.2.5.22.1.1.19 | TimeStamp | read-only | timestamp of last change to this row. |
| INT tResPlcyIngTcamEthCfm | 1.3.6.1.4.1.6527.6.2.2.2.5.22.1.1.20 | INTEGER | read-create | Ingress tcam eth cfm resource |
| INT tResPlcyIngTcamEthCfmUpMep | 1.3.6.1.4.1.6527.6.2.2.2.5.22.1.1.21 | INTEGER | read-create | Ingress tcam eth cfm up-mep resource |
| U32 tResPlcyG8032CtrlSapStartVlan | 1.3.6.1.4.1.6527.6.2.2.2.5.22.1.1.22 | Unsigned32 | read-create | G8032 control sap tag start vlan |
| U32 tResPlcyG8032CtrlSapEndVlan | 1.3.6.1.4.1.6527.6.2.2.2.5.22.1.1.23 | Unsigned32 | read-create | G8032 control sap tag End vlan |
| INT tResPlcyResIpMacMatchEnable | 1.3.6.1.4.1.6527.6.2.2.2.5.22.1.1.24 | INTEGER | read-create | Resource allocation for ip mac match enable |
| INT tResPlcyIngTcamEthCfmDownMep | 1.3.6.1.4.1.6527.6.2.2.2.5.22.1.1.25 | INTEGER | read-create | Ingress tcam eth cfm down-mep resource |
| T/F tResPlcyIngTcamEthCfmUpMepEnable | 1.3.6.1.4.1.6527.6.2.2.2.5.22.1.1.27 | TruthValue | read-write | Enable/Disable Up Mep |
| T/F tResPlcyIngTcamEthCfmDownMepEnable | 1.3.6.1.4.1.6527.6.2.2.2.5.22.1.1.28 | TruthValue | read-write | Enable/Disable Down Mep |
| sysResProfDecommObjs | 1.3.6.1.4.1.6527.6.2.2.2.5.23 | |||
| tResDecommTable | 1.3.6.1.4.1.6527.6.2.2.2.5.23.1 | not-accessible | The tResDecommTable has an entry for each user configured system decommissioned resource port. | |
| tResDecommEntry | 1.3.6.1.4.1.6527.6.2.2.2.5.23.1.1 | not-accessible | An entry in this table would be created for every decommissioned entry created | |
| INT tResDecommId | 1.3.6.1.4.1.6527.6.2.2.2.5.23.1.1.1 | INTEGER | not-accessible | system resource decommision id |
| ROW tResDecommRowStatus | 1.3.6.1.4.1.6527.6.2.2.2.5.23.1.1.2 | RowStatus | read-create | RowStatus of this policy entry |
| U32 tResDecommFromPortMap | 1.3.6.1.4.1.6527.6.2.2.2.5.23.1.1.3 | Unsigned32 | read-create | tResDecommFromPortMap is the bit map of ports that are decommissioned |
| U32 tResDecommToPortMap | 1.3.6.1.4.1.6527.6.2.2.2.5.23.1.1.4 | Unsigned32 | read-create | tResDecommToPortMap is the bit map of ports that are are allocated the resources freed up by the ports in tResDecommFromPortMap |
| tResDecommOperTable | 1.3.6.1.4.1.6527.6.2.2.2.5.23.2 | not-accessible | The tResDecommOperTable has an entry for each user configured system decommissioned resource port. This table is updated only at boot time, the entries in this table will match the entries available in tResDecommTable until administrative decommission entries are modified by the user | |
| tResDecommOperEntry | 1.3.6.1.4.1.6527.6.2.2.2.5.23.2.1 | not-accessible | An entry in this table would be created for every decommissioned entry created | |
| INT tResDecommOperId | 1.3.6.1.4.1.6527.6.2.2.2.5.23.2.1.1 | INTEGER | not-accessible | system resource decommision id |
| U32 tResDecommOperFromPortMap | 1.3.6.1.4.1.6527.6.2.2.2.5.23.2.1.2 | Unsigned32 | read-only | tResDecommOperFromPortMap is the bit map of ports that are decommissioned |
| U32 tResDecommOperToPortMap | 1.3.6.1.4.1.6527.6.2.2.2.5.23.2.1.3 | Unsigned32 | read-only | tResDecommOperToPortMap is the bit map of ports that are are allocated the resources freed up by the ports in tResDecommFromPortMap |
| sysOperGrpObjs | 1.3.6.1.4.1.6527.6.2.2.2.5.24 | |||
| TIM sysOperGrpTblLastChanged | 1.3.6.1.4.1.6527.6.2.2.2.5.24.1 | TimeStamp | read-only | The value of sysOperGrpTblLastChanged indicates the sysUpTime at the time of the last modification of sysOperGrpTable. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value. |
| sysOperGrpTable | 1.3.6.1.4.1.6527.6.2.2.2.5.24.2 | not-accessible | A table that contains Operational-Group information. | |
| sysOperGrpEntry | 1.3.6.1.4.1.6527.6.2.2.2.5.24.2.1 | not-accessible | Each row specifies information about a specific Operational-Group. | |
| TNA sysOperGrpName | 1.3.6.1.4.1.6527.6.2.2.2.5.24.2.1.1 | TNamedItem | not-accessible | The value of the object sysOperGrpName specifies the Operational-Group identifier. |
| ROW sysOperGrpRowStatus | 1.3.6.1.4.1.6527.6.2.2.2.5.24.2.1.2 | RowStatus | read-create | This value of the object sysOperGrpRowStatus specifies the status of this row. |
| TIM sysOperGrpLastChange | 1.3.6.1.4.1.6527.6.2.2.2.5.24.2.1.3 | TimeStamp | read-only | The value of sysOperGrpLastChange indicates the timestamp of last change to this row in sysOperGrpTable. |
| SER sysOperGrpOperStatus | 1.3.6.1.4.1.6527.6.2.2.2.5.24.2.1.4 | ServiceOperStatus | read-only | The value of sysOperGrpOperStatus indicates the operational state of this group. |
| TMN sysOperGrpHoldDownTime | 1.3.6.1.4.1.6527.6.2.2.2.5.24.2.1.5 | TmnxOperGrpHoldDownTime | read-create | The value of sysOperGrpHoldDownTime specifies number of seconds to wait before notifying clients monitoring this group when its operational status transitions from up to down. |
| TMN sysOperGrpCreationOrigin | 1.3.6.1.4.1.6527.6.2.2.2.5.24.2.1.6 | TmnxSysOperGrpCreationOrigin | read-only | The value of sysOperGrpCreationOrigin indicates the protocol or mechanism which created this group. |
| TMN sysOperGrpHoldUpTime | 1.3.6.1.4.1.6527.6.2.2.2.5.24.2.1.7 | TmnxOperGrpHoldUpTime | read-create | The value of sysOperGrpHoldUpTime specifies number of seconds to wait before notifying clients monitoring this group when its operational status transitions from down to up. |
| TMN sysOperGrpHoldUpTimeRemain | 1.3.6.1.4.1.6527.6.2.2.2.5.24.2.1.8 | TmnxOperGrpHoldUpTime | read-only | The value of sysOperGrpHoldUpTimeRemain indicates the number of seconds remaining in the sysOperGrpHoldUpTime. |
| TMN sysOperGrpHoldDownTimeRemain | 1.3.6.1.4.1.6527.6.2.2.2.5.24.2.1.9 | TmnxOperGrpHoldDownTime | read-only | The value of sysOperGrpHoldDownTimeRemain indicates the number of seconds remaining in the sysOperGrpHoldDownTime. |
| G32 sysOperGrpNumMembersEx | 1.3.6.1.4.1.6527.6.2.2.2.5.24.2.1.10 | Gauge32 | read-only | The value of sysOperGrpNumMembers indicates the number of members as part of this operational-group. |
| G32 sysOperGrpNumMonitoring | 1.3.6.1.4.1.6527.6.2.2.2.5.24.2.1.11 | Gauge32 | read-only | The value of sysOperGrpNumMonitoring indicates the number of objects monitoring this operational-group. |
| tmnxSASChassisObjs | 1.3.6.1.4.1.6527.6.2.2.2.6 | |||
| tmnxSASChassisNotificationObjs | 1.3.6.1.4.1.6527.6.2.2.2.6.1 | |||
| tmnxSASChassisNotification | 1.3.6.1.4.1.6527.6.2.2.2.6.2 | |||
| NTF tmnxEnvTempTooLow | 1.3.6.1.4.1.6527.6.2.2.2.6.2.1 | Generated when the temperature sensor reading on an equipment object is lesser than its configured threshold. | ||
| NTF tmnxRootDirFull | 1.3.6.1.4.1.6527.6.2.2.2.6.2.2 | Generated when the dosfs root directory is full, number of files in root directory has reached the threshold limit. | ||
| NTF tmnxEqPowerInputFailure | 1.3.6.1.4.1.6527.6.2.2.2.6.2.3 | Generated when one of the chassis's power source supplies fails. | ||
| NTF tmnxEqPowerOutputFailure | 1.3.6.1.4.1.6527.6.2.2.2.6.2.4 | Generated when one of the chassis's power output fails. | ||
| NTF tmnxEqMDACfgMissing | 1.3.6.1.4.1.6527.6.2.2.2.6.2.5 | Generated when a supported MDA is inserted into a slot, but the current configuration is not sufficient for the MDA to operate. | ||
| NTF tmnxVwmShelfInserted | 1.3.6.1.4.1.6527.6.2.2.2.6.2.6 | Generated when the vwm-shelf is inserted | ||
| NTF tmnxVwmShelfIdMismatch | 1.3.6.1.4.1.6527.6.2.2.2.6.2.7 | tmnxVwmShelfIdMismatch is when the vwm-shelf configured by the user does not match the rotary switch setting | ||
| NTF tmnxVwmShelfRemoved | 1.3.6.1.4.1.6527.6.2.2.2.6.2.8 | Generated when the vwm-shelf is removed | ||
| NTF tmnxUsbUnknownDev | 1.3.6.1.4.1.6527.6.2.2.2.6.2.9 | Generated when unsupported USB device is inserted into a 7210 device | ||
| NTF tmnxAlarmInputVoltageFailure | 1.3.6.1.4.1.6527.6.2.2.2.6.2.10 | Generated when the internal alam input voltage fails | ||
| NTF tmnxVwmShelfCardInserted | 1.3.6.1.4.1.6527.6.2.2.2.6.2.11 | Generated when a VWM shelf line card is inserted. | ||
| NTF tmnxVwmShelfCardRemoved | 1.3.6.1.4.1.6527.6.2.2.2.6.2.12 | Generated when a VWM shelf line card is removed. | ||
| NTF tmnxVwmShelfCardIdMismatch | 1.3.6.1.4.1.6527.6.2.2.2.6.2.13 | Generated when there is a VWM shelf line card mismatch with configured id. | ||
| NTF tmnxVwmShelfPSInputFailure | 1.3.6.1.4.1.6527.6.2.2.2.6.2.14 | Generated when there is a input power supply failure on VWM shelf | ||
| NTF tmnxVwmShelfPSOutputFailure | 1.3.6.1.4.1.6527.6.2.2.2.6.2.15 | Generated when there is a output power supply failure on VWM shelf | ||
| NTF tmnxVwmShelfInputLoss | 1.3.6.1.4.1.6527.6.2.2.2.6.2.16 | Generated when there is a loss on VWM shelf input | ||
| NTF tmnxVwmShelfOutputLoss | 1.3.6.1.4.1.6527.6.2.2.2.6.2.17 | Generated when there is a loss on VWM shelf output | ||
| NTF tmnxVwmShelfCardCfgError | 1.3.6.1.4.1.6527.6.2.2.2.6.2.18 | Generated when the vwm shelf inserted does not match with configured shelf id, card | ||
| NTF sysOperGrpOperStatusChanged | 1.3.6.1.4.1.6527.6.2.2.2.6.2.25 | [CAUSE] The svcOperGrpOperStatusChanged notification is generated when there is a change in the value of svcOperGrpOperStatus. [EFFECT] Status of the one or more of the members of the operational group has changed. [RECOVERY] Operational status of the members of the operational-group will need to be investigated. | ||
| tmnxChassisExtnTable | 1.3.6.1.4.1.6527.6.2.2.2.6.3 | not-accessible | The chassis table has an entry for each chassis in the system. This table extends the tmnxChassisTable for the SAS platform | |
| tmnxChassisExtnEntry | 1.3.6.1.4.1.6527.6.2.2.2.6.3.1 | not-accessible | An entry in this table would be created for every entry in the tmnxChassisEntry | |
| TMN tmnxChassisUpdateGoldenBootstrapImage | 1.3.6.1.4.1.6527.6.2.2.2.6.3.1.1 | TmnxActionType | read-write | Setting this action variable to 'doAction' causes the current golden bootstrap image to be updated with the image at the location specified by tmnxChassisGoldenBootstrapImageSrc. If no location is specified by tmnxChassisGoldenBootstrapImageSrc, cf1:/boot.tim will be saved as the golden bootstrap image. |
| STR tmnxChassisGoldenBootstrapImageSrc | 1.3.6.1.4.1.6527.6.2.2.2.6.3.1.2 | DisplayString | read-write | The value of tmnxChassisGoldenBootstrapImageSrc specifies the source filepath or file-URL which will be saved as the golden bootstrap image when tmnxChassisUpdateGoldenBootstrapImage is set to 'doAction'. If 'tmnxChassisGoldenBootstrapImage' is set to the empty string, ''H, cf1:/boot.tim will be saved as the golden bootstrap image. |
| TMN tmnxChassisValidateGoldenBootstrapImage | 1.3.6.1.4.1.6527.6.2.2.2.6.3.1.3 | TmnxActionType | read-write | Setting this action variable to 'doAction' causes the current golden bootstrap image to be validated and upon completion tmnxChassisGoldenBootstrapImageVersion will be populated with its version. If the validation fails tmnxChassisGoldenBootstrapImageVersion will be populated apropriately. |
| STR tmnxChassisGoldenBootstrapImageVersion | 1.3.6.1.4.1.6527.6.2.2.2.6.3.1.4 | DisplayString | read-only | This object is populated with the version of the golden bootstrap image when validation is completed. If the validation fails, one of the following values is set: 'Invalid Golden Bootstrap Image' - Indicates the image is invalid. |
| TMN tmnxChassisRebootAutoInit | 1.3.6.1.4.1.6527.6.2.2.2.6.3.1.5 | TmnxActionType | read-write | Setting this action variable to 'doAction', will reset the bof and reboot the system |
| INT tmnxChassisLowTempState | 1.3.6.1.4.1.6527.6.2.2.2.6.3.1.6 | INTEGER | read-only | The current Low Temperature state of this chassis. stateOk Indicates chassis is above the low temperature threshold. stateLowTemp Indicates chassis is below the low temperature threshold. |
| TMN tmnxChassisSystemLEDState | 1.3.6.1.4.1.6527.6.2.2.2.6.3.1.7 | TmnxLEDState | read-only | The current state of the System LED in this chassis. |
| tmnxHwExtnTable | 1.3.6.1.4.1.6527.6.2.2.2.6.4 | not-accessible | The tmnxHwTable has an entry for each managed hardware component. This table extends the TmnxHwEntry for the SAS platform | |
| tmnxHwExtnEntry | 1.3.6.1.4.1.6527.6.2.2.2.6.4.1 | not-accessible | An entry in this table would be created for every entry in the tmnxChassisEntry | |
| I32 tmnxHwLowTempThreshold | 1.3.6.1.4.1.6527.6.2.2.2.6.4.1.1 | Integer32 | read-only | The low temperature threshold for this hardware component in degrees celsius. When the value of tmnxHwTemperature lowers below tmnxHwLowTempThreshold, a 'temperature too low' event will be generated. |
| tmnxFabricPolicyTable | 1.3.6.1.4.1.6527.6.2.2.2.6.5 | not-accessible | This table provides the context to configure the fabric policy in use by different applications. Currently, PBB is the only application using it and only one default object is supported | |
| tmnxFabricPolicyEntry | 1.3.6.1.4.1.6527.6.2.2.2.6.5.1 | not-accessible | ||
| TPO tmnxFabricPolicyIndex | 1.3.6.1.4.1.6527.6.2.2.2.6.5.1.1 | TPolicyID | not-accessible | the policy ID is the index to this table. |
| ROW tmnxFabricPolicyRowStatus | 1.3.6.1.4.1.6527.6.2.2.2.6.5.1.2 | RowStatus | read-create | Row Status for the policy. |
| TCI tmnxFabricPolicyCIR | 1.3.6.1.4.1.6527.6.2.2.2.6.5.1.3 | TCIRRate | read-create | The CIR specified by the user. |
| TPI tmnxFabricPolicyPIR | 1.3.6.1.4.1.6527.6.2.2.2.6.5.1.4 | TPIRRate | read-create | The PIR specified by the user. |
| TBU tmnxFabricPolicyCBS | 1.3.6.1.4.1.6527.6.2.2.2.6.5.1.5 | TBurstSize | read-create | The amount of reserved buffer space (in kilo bytes). |
| TBU tmnxFabricPolicyMBS | 1.3.6.1.4.1.6527.6.2.2.2.6.5.1.6 | TBurstSize | read-create | The maximum amount of buffer space (in kilo bytes) allowed |
| I32 tmnxFabricPolicyMpointFabricPort | 1.3.6.1.4.1.6527.6.2.2.2.6.5.1.7 | Integer32 | read-create | |
| tmnxChassisPowerSupplyExtnTable | 1.3.6.1.4.1.6527.6.2.2.2.6.6 | not-accessible | This table extends the Power Supply Information defined in tmnxChassisPowerSupplyTable | |
| tmnxChassisPowerSupplyExtnEntry | 1.3.6.1.4.1.6527.6.2.2.2.6.6.1 | not-accessible | Contains information regarding a power supply tray. | |
| INT tmnxChassisPowerSupplyAssignedDCType | 1.3.6.1.4.1.6527.6.2.2.2.6.6.1.1 | INTEGER | read-only | tmnxChassisPowerSupplyAssignedDCType when set to `m48-dc`, the power supply is -48V DC, when set to P24-dc it is +24V DC. tmnxChassisPowerSupplyAssignedDCType is set to m48-dc or p24-dc if tmnxChassisPowerSupplyAssignedType is of type `dc`, If tmnxChassisPowerSupplyAssignedType is not `dc` tmnxChassisPowerSupplyAssignedDCType will be set to not-applicable. |
| tmnxChassisFanExtnTable | 1.3.6.1.4.1.6527.6.2.2.2.6.7 | not-accessible | This table extends the system fan information | |
| tmnxChassisFanExtnEntry | 1.3.6.1.4.1.6527.6.2.2.2.6.7.1 | not-accessible | Contains information regarding Fan tray. | |
| TMN tmnxChassisFanCfgMode | 1.3.6.1.4.1.6527.6.2.2.2.6.7.1.1 | TmnxFanCfgMode | read-create | tmnxChassisFanCfgMode is the configuration object used to determine how the fan in controlled. It can be either user controlled (on|off) or in 'auto' mode where the operation will be based on threshold values. |
| INT tmnxChassisFanOperMode | 1.3.6.1.4.1.6527.6.2.2.2.6.7.1.2 | INTEGER | read-only | tmnxChassisFanOperMode is a read only object which will determine the current mode of operation. |
| tmnxSASCardObjs | 1.3.6.1.4.1.6527.6.2.2.2.6.8 | |||
| tmnxCardExtnTable | 1.3.6.1.4.1.6527.6.2.2.2.6.8.1 | not-accessible | The tmnxCardExtnTable has an entry for each one of the entry in tmnxCardTable | |
| tmnxCardExtnEntry | 1.3.6.1.4.1.6527.6.2.2.2.6.8.1.1 | not-accessible | The tmnxCardExtnEntry extends tmnxCardEntry capabilities | |
| INT tmnxCardSysResPlcyId | 1.3.6.1.4.1.6527.6.2.2.2.6.8.1.1.1 | INTEGER | read-write | system resource policy id attached to this card |
| tmnxCpmCardExtnTable | 1.3.6.1.4.1.6527.6.2.2.2.6.8.2 | not-accessible | The tmnxCpmCardExtnTable has an entry for each CPM card or module in each chassis in the TMNX system. | |
| tmnxCpmCardExtnEntry | 1.3.6.1.4.1.6527.6.2.2.2.6.8.2.1 | not-accessible | Each row entry represents a CPM card or module in a chassis in the system. Entries cannot be created and deleted via SNMP SET operations. When a tmnxChassisEntry is created, a tmnxCpmCardExtnEntry is created for each CPM card or module in that chassis. Before a tmnxChassisEntry can be deleted, each tmnxCpmCardEntry for that chassis must be in the proper state for removal. | |
| STR tmnxCpmCardBootImageSource | 1.3.6.1.4.1.6527.6.2.2.2.6.8.2.1.1 | DisplayString | read-only | tmnxCpmCardBootImageSource indicates the compact flash slot where the Boot image file was found when the system last rebooted. For example, if the BOF file was found on compact flash slot 1, the value of this variable will be 'cf1:' |
| aluExtTmnxChassisTable | 1.3.6.1.4.1.6527.6.2.2.2.6.9 | not-accessible | The chassis table has an entry for each chassis in the system. | |
| aluExtTmnxChassisEntry | 1.3.6.1.4.1.6527.6.2.2.2.6.9.1 | not-accessible | Each row entry represents a chassis in the system. The agent creates the row for the first chassis in the system, with tmnxChassisIndex = 1, which is auto-discovered by the active CPM card. Additional chassis entries can be created and deleted via SNMP SET operations. Creation requires a SET request containing at least tmnxChassisAdminMode and tmnxChassisRowStatus. Note that the first Alcatel 7x50 series product release does not support multiple chassis, therefore there will not be more than one row entry in this table; attempts to create additional rows in this table will be denied. | |
| INT aluExtPoePowerMode | 1.3.6.1.4.1.6527.6.2.2.2.6.9.1.3 | INTEGER | read-write | aluExtPoePowerMode represents set of poe capabilities, the mode is general for all MDAs, ports |
| INT aluExtPoePowerSupplyStatus | 1.3.6.1.4.1.6527.6.2.2.2.6.9.1.4 | INTEGER | read-only | Current status of the PoE Power Supply. |
| INT aluExtPoeExternalPowerSupplyStatus | 1.3.6.1.4.1.6527.6.2.2.2.6.9.1.5 | INTEGER | read-only | Current status of the PoE External Power Supply connection |
| tCardResOperTable | 1.3.6.1.4.1.6527.6.2.2.2.6.10 | not-accessible | The tCardResOperTable has an entry for each CPM card or module in each chassis in the TMNX system, this table provides the operations system resource values used on the card | |
| tCardResOperEntry | 1.3.6.1.4.1.6527.6.2.2.2.6.10.1 | not-accessible | Each row entry represents a CPM card or module in a chassis in the system. Entries cannot be created and deleted via SNMP SET operations. When a tmnxChassisEntry is created, a tCardResOperEntry is created for each CPM card or module in that chassis. Before a tmnxChassisEntry can be deleted, each tCardResOperEntry for that chassis must be in the proper state for removal. | |
| INT tCardResOperIngTcamSapAggMeter | 1.3.6.1.4.1.6527.6.2.2.2.6.10.1.1 | INTEGER | read-only | Ingress tcam sap aggregate meter resource |
| INT tCardResOperIngTcamQosSapIng | 1.3.6.1.4.1.6527.6.2.2.2.6.10.1.2 | INTEGER | read-only | Ingress tcam sap sap ingress resource |
| INT tCardResOperIngTcamQosSapIngIpv4 | 1.3.6.1.4.1.6527.6.2.2.2.6.10.1.3 | INTEGER | read-only | Ingress tcam sap ingress ipv4 resource |
| INT tCardResOperIngTcamQosSapIngIpv4Ipv6 | 1.3.6.1.4.1.6527.6.2.2.2.6.10.1.4 | INTEGER | read-only | Ingress tcam sap ingress ipv4, ipv6 resource |
| INT tCardResOperIngTcamQosSapIngMac | 1.3.6.1.4.1.6527.6.2.2.2.6.10.1.5 | INTEGER | read-only | Ingress tcam sap ingress mac resource |
| INT tCardResOperIngTcamAclSapIng | 1.3.6.1.4.1.6527.6.2.2.2.6.10.1.6 | INTEGER | read-only | Ingress tcam acl sap ingress resource |
| INT tCardResOperIngTcamAclSapIngIpv4 | 1.3.6.1.4.1.6527.6.2.2.2.6.10.1.7 | INTEGER | read-only | Ingress tcam acl sap ingress ipv4 resource |
| INT tCardResOperIngTcamAclSapIng64Ipv6 | 1.3.6.1.4.1.6527.6.2.2.2.6.10.1.8 | INTEGER | read-only | Ingress tcam acl sap ingress 64 bit ipv6 match resource |
| INT tCardResOperIngTcamAclSapIng128Ipv4Ipv6 | 1.3.6.1.4.1.6527.6.2.2.2.6.10.1.9 | INTEGER | read-only | Ingress tcam acl sap ingress 128 bit ipv6 resource |
| INT tCardResOperIngTcamAclSapIngMac | 1.3.6.1.4.1.6527.6.2.2.2.6.10.1.10 | INTEGER | read-only | Ingress tcam acl sap ingress mac resource |
| INT tCardResOperEgrTcamAclSapEgr | 1.3.6.1.4.1.6527.6.2.2.2.6.10.1.11 | INTEGER | read-only | Egress tcam acl sap sap egress 1resource |
| INT tCardResOperEgrTcamAclSapEgrMacIpv4 | 1.3.6.1.4.1.6527.6.2.2.2.6.10.1.12 | INTEGER | read-only | Egress tcam acl sap egress mac ipv4 resource |
| INT tCardResOperEgrTcamAclSapEgr128Ipv6 | 1.3.6.1.4.1.6527.6.2.2.2.6.10.1.13 | INTEGER | read-only | Egress tcam acl sap egress 128bit ipv6 resource |
| INT tCardResOperEgrTcamAclSapEgr64MacIpv6 | 1.3.6.1.4.1.6527.6.2.2.2.6.10.1.14 | INTEGER | read-only | Egress tcam acl sap egress mac resource |
| INT tCardResOperEgrTcamAclSapEgrMac | 1.3.6.1.4.1.6527.6.2.2.2.6.10.1.15 | INTEGER | read-only | Egress tcam acl sap egress mac resource |
| INT tCardResOperIngTcamEthCfm | 1.3.6.1.4.1.6527.6.2.2.2.6.10.1.18 | INTEGER | read-only | Ingress tcam eth cfm resource |
| INT tCardResOperIngTcamEthCfmUpMep | 1.3.6.1.4.1.6527.6.2.2.2.6.10.1.19 | INTEGER | read-only | Ingress tcam eth cfm up-mep resource |
| U32 tCardResOperG8032CtrlSapStartVlan | 1.3.6.1.4.1.6527.6.2.2.2.6.10.1.20 | Unsigned32 | read-only | G8032 control sap tag start vlan |
| U32 tCardResOperG8032CtrlSapEndVlan | 1.3.6.1.4.1.6527.6.2.2.2.6.10.1.21 | Unsigned32 | read-only | G8032 control sap tag End vlan |
| INT tCardResOperResIpMacMatchEnable | 1.3.6.1.4.1.6527.6.2.2.2.6.10.1.22 | INTEGER | read-only | Resource allocation for ip mac match enable |
| INT tCardResOperIngTcamEthCfmDownMep | 1.3.6.1.4.1.6527.6.2.2.2.6.10.1.23 | INTEGER | read-only | Ingress tcam eth cfm down-mep resource |
| INT tCardResOperIngTcamIpMulticast | 1.3.6.1.4.1.6527.6.2.2.2.6.10.1.24 | INTEGER | read-only | tCardResOperIngTcamIpMulticast sets the resource to be used for ip-multicast. |
| tmnxSASSecurityObjects | 1.3.6.1.4.1.6527.6.2.2.2.15 | |||
| tmnxSASSecurityNotificationObjs | 1.3.6.1.4.1.6527.6.2.2.2.15.5 | |||
| TNA tmnxLoginUserName | 1.3.6.1.4.1.6527.6.2.2.2.15.5.1 | TNamedItem | accessible-for-notify | The value of tmnxUserName specifies the name for a system user. This name must be unique amongst the table entries. tmnxUserName will be sent in the notifications when the user crosses the threshold login attempts configured in tmnxPasswordAttemptsCount |
| IP tmnxLoginUserSrcIPAddress | 1.3.6.1.4.1.6527.6.2.2.2.15.5.2 | InetAddress | accessible-for-notify | The value of tmnxLoginUserSrcIPAddress specifies the source address of the client station from where the user has tried to login |
| INT tmnxLoginMaxAttempts | 1.3.6.1.4.1.6527.6.2.2.2.15.5.3 | INTEGER | accessible-for-notify | The value of tmnxLoginMaxAttempts specifies the number of times user could attempt to login before raising a max attempt trap |
| STR tmnxChassisNotifyMDACfgFailReason | 1.3.6.1.4.1.6527.6.2.2.2.15.5.4 | DisplayString | accessible-for-notify | Used by tmnxEqMDACfgMissing, the value of tmnxChassisNotifyMDACfgFailReason contains the reason for MDA config failure. |
| tmnxSASSysMIBNotifyPrefix | 1.3.6.1.4.1.6527.6.2.2.3.1 | |||
| tmnxSASSysNotifications | 1.3.6.1.4.1.6527.6.2.2.3.1.3 | |||
| NTF tmnxDyingGasp | 1.3.6.1.4.1.6527.6.2.2.3.1.3.1 | tmnxDyingGasp trap is generated when the system goes down due to power failure. System would make best effort to send out this trap with the power remaining in Dying Gasp capacitor | ||
| tmnxSASSecurityNotifyPrefix | 1.3.6.1.4.1.6527.6.2.2.3.2 | |||
| tmnxSASSecurityNotifications | 1.3.6.1.4.1.6527.6.2.2.3.2.0 | |||
| NTF tmnxUserLoginMaxAttempts | 1.3.6.1.4.1.6527.6.2.2.3.2.0.1 | The tmnxUserLoginMaxAttempts is generated when a user failed to authenticate in more than the permitted number of login retries. | ||
| NTF tmnxSSHUserLoginMaxAttempts | 1.3.6.1.4.1.6527.6.2.2.3.2.0.3 | The tmnxSSHUserLoginMaxAttempts is generated when a user failed to authenticate in more than the permitted number of login retries through SSH. |
RFC description
Nokia Timetra vendor-private MIB for managing Service Assurance Service (SAS) system operations.
Start monitoring Nokia/Alcatel-Lucent 7210 SAS Service Access Switch (dual-uplink redundancy/keepalive status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.