All MIBs › TIMETRA-GMPLS-MIB
Organization: Nokia
Last Updated: 2014-04-02
Description: TIMETRA-GMPLS-MIB module
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is TIMETRA-GMPLS-MIB?
TIMETRA-GMPLS-MIB is a Nokia (formerly Alcatel-Lucent) enterprise MIB that manages and provisions Generalized MPLS (GMPLS) extensions on the SROS operating system used by 7750 SR and related routers. It falls into the MPLS/traffic-engineering configuration and status category, exposing per-virtual-router GMPLS general configuration and operational objects, including administrative/operational state, keepalive multiplier, LSP initialization retry timing, refresh timers, and rapid-retransmission parameters, plus a notification-prefix and conformance structure. Its monitoring value is on software/protocol status rather than physical hardware — confirming a virtual router's GMPLS instance is administratively and operationally up (vRtrGmplsGeneralAdminState/OperState), and that keepalive and LSP-retry timers are tuned appropriately to avoid unnecessary session flaps in optical/transport-integrated MPLS networks. It builds on Nokia's broader TIMETRA/SROS enterprise MIB tree and extends the standard MPLS/GMPLS signaling model (RFC 3945 and related GMPLS RFCs) into a vendor-specific management view. It is typically deployed on Nokia 7750 SR (and related SROS) routers in carrier networks that integrate packet and optical/transport GMPLS-controlled links. Engineers can download the TIMETRA-GMPLS-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in TIMETRA-GMPLS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Nokia (Alcatel-Lucent) 7750 SR router (SROS, GMPLS-enabled)
Monitoring Examples
An operator would poll vRtrGmplsGeneralTable/vRtrGmplsGeneralEntry to check vRtrGmplsGeneralAdminState against vRtrGmplsGeneralOperState for a virtual router's GMPLS instance, confirming it is both administratively enabled and operationally up. Reviewing vRtrGmplsGeneralKeepMultiplier, vRtrGmplsGenLspInitRetryTimeout, and vRtrGmplsGenRapidRetransmitTime/vRtrGmplsGenRapidRetryLimit would reveal whether GMPLS keepalive/retry timers are set too aggressively, a likely cause if the operator is seeing frequent unexpected GMPLS session or LSP re-establishment events (tmnxGmplsNotifyPrefix-rooted traps).
What Can Be Monitored
- GMPLS admin/operational state per virtual router
- keepalive multiplier/timer settings
- LSP initialization retry timeout
- rapid retransmit time/retry limit
- GMPLS notification/trap activity
This MIB depends on
Related MIBs
Imported Objects
From INET-ADDRESS-MIB
| InetAddress | |
| InetAddressType |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Counter64 | |
| Gauge32 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| DisplayString | |
| RowPointer | |
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TestAndIncr | |
| TimeInterval | |
| TimeStamp | |
| TruthValue |
From TIMETRA-GLOBAL-MIB
| timetraSRMIBModules | OBJECT-IDENTITY |
| tmnxSRConfs | OBJECT-IDENTITY |
| tmnxSRNotifyPrefix | OBJECT-IDENTITY |
| tmnxSRObjs | OBJECT-IDENTITY |
From TIMETRA-LMP-MIB
| tmnxLmpVRtrPeerNodeId | OBJECT-TYPE |
| tmnxLmpVRtrTeLinkId | OBJECT-TYPE |
From TIMETRA-TC-MIB
| TItemDescription | |
| TNamedItem | |
| TNamedItemOrEmpty | |
| TmnxAdminState | |
| TmnxEnabledDisabled | |
| TmnxOperState | |
| TmnxPortID |
From TIMETRA-VRTR-MIB
| tmnxSrlgGrpName | |
| vRtrID | OBJECT-TYPE |
| vRtrIfIndex | OBJECT-TYPE |
How to Use in IPNetwork Monitor
Example using vRtrGmplsPeerHelloTimeoutCount OID:
Select a Nokia (Alcatel-Lucent) 7750 SR router, SROS GMPLS-enabled (GMPLS instance admin/oper status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type vRtrGmplsPeerHelloTimeoutCount into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The value of vRtrGmplsPeerHelloTimeoutCount indicates number of times the Hello timeout timer expired for the peer. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| timetraGmplsMIBModule | 1.3.6.1.4.1.6527.1.1.3.97 | This document is the SNMP MIB module to manage and provision the GMPLS extensions for the Nokia SROS device. Copyright 2003-2016 Nokia. All rights reserved. Reproduction of this document is authorized on the condition that the foregoing copyright notice is included. This SNMP MIB module (Specification) embodies Nokia's proprietary intellectual property. Nokia retains all title and ownership in the Specification, including any revisions. Nokia grants all interested parties a non-exclusive license to use and distribute an unmodified copy of this Specification in connection with management of Nokia products, and without fee, provided this copyright notice and license appear on all copies. This Specification is supplied 'as is', and Nokia makes no warranty, either express or implied, as to the use, operation, condition, or performance of the Specification. | ||
| tmnxGmplsConformance | 1.3.6.1.4.1.6527.3.1.1.97 | |||
| tmnxGmplsCompliances | 1.3.6.1.4.1.6527.3.1.1.97.1 | |||
| tmnxGmplsV13v0Compliance | 1.3.6.1.4.1.6527.3.1.1.97.1.1 | The compliance statement for management of origin validation instances on Nokia SROS series systems release 13.0. | ||
| tmnxGmplsGroups | 1.3.6.1.4.1.6527.3.1.1.97.2 | |||
| tmnxGmplsGeneralV13v0Group | 1.3.6.1.4.1.6527.3.1.1.97.2.1 | The group of objects supporting the management of GMPLS protocol in version 13.0 of Nokia SROS series systems. | ||
| tmnxGmplsPathV13v0Group | 1.3.6.1.4.1.6527.3.1.1.97.2.2 | The group of objects supporting management of GMPLS Path objects on Nokia SROS series systems in version 13.0. | ||
| tmnxGmplsPeerV13v0Group | 1.3.6.1.4.1.6527.3.1.1.97.2.3 | The group of objects supporting management of Peer objects for GMPLS on Nokia SROS series systems in version 13.0. | ||
| tmnxGmplsLspV13v0Group | 1.3.6.1.4.1.6527.3.1.1.97.2.4 | The group of objects supporting management of Labeled Switch Path (LSP) objects for GMPLS on Nokia SROS series systems in version 13.0. | ||
| tmnxGmplsTunGrpV13v0Group | 1.3.6.1.4.1.6527.3.1.1.97.2.5 | The group of objects supporting management of GMPLS Tunnel Group objects on Nokia SROS series systems in version 13.0. | ||
| tmnxGmplsTunGrpMemberV13v0Group | 1.3.6.1.4.1.6527.3.1.1.97.2.6 | The group of objects supporting management of GMPLS Tunnel Group Member objects on Nokia SROS series systems in version 13.0. | ||
| tmnxGmplsTeLinkV13v0Group | 1.3.6.1.4.1.6527.3.1.1.97.2.7 | The group of objects supporting management of GMPLS Traffic Engineering (TE) Link objects on Nokia SROS series systems in version 13.0 | ||
| tmnxGmplsSessionV13v0Group | 1.3.6.1.4.1.6527.3.1.1.97.2.8 | The group of objects supporting management of GMPLS session objects on Nokia SROS series systems in version 13.0. | ||
| tmnxGmplsARHopV13v0Group | 1.3.6.1.4.1.6527.3.1.1.97.2.9 | The group of objects supporting management of GMPLS actual hops on Nokia SROS series systems in version 13.0. | ||
| tmnxGmplsNotificationV13v0Group | 1.3.6.1.4.1.6527.3.1.1.97.2.10 | The group of notifications supporting management of objects for GMPLS on Nokia SROS series systems in version 13.0. | ||
| tmnxGmplsCommandGroup | 1.3.6.1.4.1.6527.3.1.1.97.2.11 | The group of objects supporting management of GMPLS command switch objects on Nokia SROS series systems in version 13.0. | ||
| tmnxGmplsV13v1Group | 1.3.6.1.4.1.6527.3.1.1.97.2.12 | The group of objects supporting management of GMPLS objects on Nokia SROS series systems in version 13.0. | ||
| tmnxGmplsObjs | 1.3.6.1.4.1.6527.3.1.2.97 | |||
| TIM vRtrGmplsGeneralTblLastChanged | 1.3.6.1.4.1.6527.3.1.2.97.1 | TimeStamp | read-only | The value of vRtrGmplsGeneralTblLastChanged indicates the sysUpTime at the time of the last modification to vRtrGmplsGeneralTable by adding, deleting an entry or change to a writable object in the table. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value. |
| vRtrGmplsGeneralTable | 1.3.6.1.4.1.6527.3.1.2.97.2 | not-accessible | The vRtrGmplsGeneralTable contains objects for general control and management of GMPLS protocol instance within a virtual router. | |
| vRtrGmplsGeneralEntry | 1.3.6.1.4.1.6527.3.1.2.97.2.1 | not-accessible | The vRtrGmplsGeneralEntry contains configuration items for the GMPLS protocol running within a virtual router. | |
| ROW vRtrGmplsGeneralRowStatus | 1.3.6.1.4.1.6527.3.1.2.97.2.1.1 | RowStatus | read-create | The value of vRtrGmplsGeneralRowStatus specifies the row status used for creation, deletion, or control of vRtrGmplsGeneralTable entries. |
| TIM vRtrGmplsGeneralLastChange | 1.3.6.1.4.1.6527.3.1.2.97.2.1.2 | TimeStamp | read-only | The value of vRtrGmplsGeneralLastChange indicates the sysUpTime when this row was last modified. |
| TMN vRtrGmplsGeneralAdminState | 1.3.6.1.4.1.6527.3.1.2.97.2.1.3 | TmnxAdminState | read-create | The value of vRtrGmplsGeneralAdminState specifies whether GMPLS protocol is enabled or disabled. When vRtrGmplsGeneralAdminState is set to 'inService', the agent attempts to enable the GMPLS protocol instance on this router. When vRtrGmplsGeneralAdminState is set to 'outOfService', the agent attempts to disable the GMPLS protocol instance on this router. |
| TMN vRtrGmplsGeneralOperState | 1.3.6.1.4.1.6527.3.1.2.97.2.1.4 | TmnxOperState | read-only | The value of vRtrGmplsGeneralOperState indicates the current operating state of this GMPLS protocol instance on this router. |
| U32 vRtrGmplsGeneralKeepMultiplier | 1.3.6.1.4.1.6527.3.1.2.97.2.1.5 | Unsigned32 | read-create | The value of vRtrGmplsGeneralKeepMultiplier specifies if it is used by GMPLS to declare either a reservation down or the neighbor as down. |
| U32 vRtrGmplsGenLspInitRetryTimeout | 1.3.6.1.4.1.6527.3.1.2.97.2.1.6 | Unsigned32 | read-create | The value of vRtrGmplsGenLspInitRetryTimeout specifies the amount of time in seconds the software waits for an LSP path to come up after sending out the initial Path message. If the initial retry timeout period expires and the LSP path is not up, it is torn down and the LSP retry timer is started to schedule a new retry cycle using a new LSP-id. |
| U32 vRtrGmplsGeneralRefreshTime | 1.3.6.1.4.1.6527.3.1.2.97.2.1.7 | Unsigned32 | read-create | The value of vRtrGmplsGeneralRefreshTime controls the interval between the successive Path and Resv refresh messages. GMPLS declares the session down after it misses ((keep-multiplier + 0.5) * 1.5 * refresh-time)) consecutive refresh messages. |
| U32 vRtrGmplsGenRapidRetransmitTime | 1.3.6.1.4.1.6527.3.1.2.97.2.1.8 | Unsigned32 | read-create | The value of vRtrGmplsGenRapidRetransmitTime specifies the value of the rapid retransmission interval. This is used in the retransmission mechanism based on an exponential backoff timer in order to handle unacknowledged message objects. vRtrGmplsGenRapidRetransmitTime must be smaller than the regular refresh interval vRtrGmplsGeneralRefreshTime. |
| U32 vRtrGmplsGenRapidRetryLimit | 1.3.6.1.4.1.6527.3.1.2.97.2.1.9 | Unsigned32 | read-create | The value of vRtrGmplsGenRapidRetryLimit specifies the rapid retry limit. This is used in the retransmission mechanism based on an exponential backoff timer in order to handle unacknowledged message objects. The node stops retransmission of unacknowledged GMPLS messages whenever the updated backoff interval exceeds the value of vRtrGmplsGeneralRefreshTime or the number of retransmissions reaches the value of the vRtrGmplsGenRapidRetryLimit, whichever comes first. |
| U32 vRtrGmplsGenGrHlprMaxRcvryTm | 1.3.6.1.4.1.6527.3.1.2.97.2.1.10 | Unsigned32 | read-create | The value of vRtrGmplsGenGrHlprMaxRcvryTm specifies the maximum time in seconds, a graceful helper will wait for session recovery. This value is compared with the neighbor's advertised recovery time and the minimum of the two is used. This value is used to cap the recovery time advertised by the neighbor. |
| U32 vRtrGmplsGenGrHlprMaxRstrtTm | 1.3.6.1.4.1.6527.3.1.2.97.2.1.11 | Unsigned32 | read-create | The value of vRtrGmplsGenGrHlprMaxRstrtTm specifies the maximum time in seconds a graceful helper will wait for session restart after it has determined that the neighbor is down. This value is compared with the neighbor's advertised restart time and the minimum of the two is used. This is used to cap the restart time advertised by the neighbor. |
| INT vRtrGmplsGenOperDownReasonCode | 1.3.6.1.4.1.6527.3.1.2.97.2.1.12 | INTEGER | read-only | The value of vRtrGmplsGenOperDownReasonCode indicates the reason that the GMPLS instance is operationally down. |
| U32 vRtrGmplsGeneralLocalNodeId | 1.3.6.1.4.1.6527.3.1.2.97.2.1.13 | Unsigned32 | read-only | The value of vRtrGmplsGeneralLocalNodeId indicates the local Node ID of this GMPLS instance. |
| I32 vRtrGmplsPathIndexNext | 1.3.6.1.4.1.6527.3.1.2.97.3 | Integer32 | read-only | The value of vRtrGmplsPathIndexNext indicates the next appropriate value to be used for vRtrGmplsPathIndex when creating entries in the vRtrGmplsPathTable. If the number of unassigned entries is exhausted, a retrival operation will return a value of 0. To obtain the value of vRtrGmplsPathIndex for a new entry, the manager must first issue a management protocol retrieval operation to obtain the current value of this object. The agent should modify the value to reflect the next unassigned index after each retrieval operation. After a manager retrieves a value the agent will determine through its local policy when this index value will be made available for reuse. |
| TIM vRtrGmplsPathTblLastChanged | 1.3.6.1.4.1.6527.3.1.2.97.4 | TimeStamp | read-only | The value of vRtrGmplsPathTblLastChanged indicates the sysUpTime at the time of the last modification to vRtrGmplsPathTable by adding, deleting an entry or change to a writable object in the table. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value. |
| vRtrGmplsPathTable | 1.3.6.1.4.1.6527.3.1.2.97.5 | not-accessible | The vRtrGmplsPathTable contains objects for GMPLS path table. | |
| vRtrGmplsPathEntry | 1.3.6.1.4.1.6527.3.1.2.97.5.1 | not-accessible | Each row entry in vRtrGmplsPathEntry represents a GMPLS Path configured for a virtual router in the system. Entries can be created and deleted via SNMP SET operations. Setting RowStatus to 'active' requires vRtrGmplsPathName to have been assigned a valid value. | |
| I32 vRtrGmplsPathIndex | 1.3.6.1.4.1.6527.3.1.2.97.5.1.1 | Integer32 | not-accessible | The value of object vRtrGmplsPathIndex indicates the unique value which identifies this GMPLS Path for this virtual router in the Nokia SROS system. It is a unique value among entries with the same value of vRtrID. |
| ROW vRtrGmplsPathRowStatus | 1.3.6.1.4.1.6527.3.1.2.97.5.1.2 | RowStatus | read-create | The value of vRtrGmplsPathRowStatus specifies the row status used for creation, deletion, or control of vRtrGmplsPathTable entries. |
| TIM vRtrGmplsPathLastChange | 1.3.6.1.4.1.6527.3.1.2.97.5.1.3 | TimeStamp | read-only | The value of vRtrGmplsPathLastChange indicates the sysUpTime when this row was last modified. |
| TNA vRtrGmplsPathName | 1.3.6.1.4.1.6527.3.1.2.97.5.1.4 | TNamedItemOrEmpty | read-create | The value of vRtrGmplsPathName specifies administrative name for this GMPLS Path. The vRtrGmplsPathName must be unique within a virtual router instance. The value of vRtrGmplsPathName needs to be specified when creating a new entry in this table. |
| TMN vRtrGmplsPathAdminState | 1.3.6.1.4.1.6527.3.1.2.97.5.1.5 | TmnxAdminState | read-create | The value of vRtrGmplsPathAdminState specifies the desired administrative state for this GMPLS path. |
| TMN vRtrGmplsPathOperState | 1.3.6.1.4.1.6527.3.1.2.97.5.1.6 | TmnxOperState | read-only | The value of vRtrGmplsPathOperState indicates the current operational state of this GMPLS path. |
| TIM vRtrGmplsPathHopTblLastChanged | 1.3.6.1.4.1.6527.3.1.2.97.6 | TimeStamp | read-only | The value of vRtrGmplsPathHopTblLastChanged indicates the sysUpTime at the time of the last modification to vRtrGmplsPathHopTable by adding, deleting an entry or change to a writable object in the table. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value. |
| vRtrGmplsPathHopTable | 1.3.6.1.4.1.6527.3.1.2.97.7 | not-accessible | The vRtrGmplsPathHopTable is used to indicate the hops, strict or loose, for a GMPLS path defined in vRtrGmplsPathTable. Each row in this table is indexed primarily by the same index vRtrGmplsPathIndex, as the row of the corresponding table in vRtrGmplsPathTable. Each row also has a secondary index vRtrGmplsPathHopIndex corresponding to the next hop that this row corresponds to. | |
| vRtrGmplsPathHopEntry | 1.3.6.1.4.1.6527.3.1.2.97.7.1 | not-accessible | The vRtrGmplsPathHopEntry contains configuration items for GMPLS path hop table. | |
| I32 vRtrGmplsPathHopIndex | 1.3.6.1.4.1.6527.3.1.2.97.7.1.1 | Integer32 | not-accessible | The value of vRtrGmplsPathHopIndex indicates the unique value which identifies the GMPLS Path Hop for this virtual router in the Nokia SROS system. It is a unique value among entries with the same value of vRtrID. |
| ROW vRtrGmplsPathHopRowStatus | 1.3.6.1.4.1.6527.3.1.2.97.7.1.2 | RowStatus | read-create | The value of vRtrGmplsPathHopRowStatus specifies the row status used for creation, deletion, or control of vRtrGmplsPathHopTable entries. |
| TIM vRtrGmplsPathHopLastChange | 1.3.6.1.4.1.6527.3.1.2.97.7.1.3 | TimeStamp | read-only | The value of vRtrGmplsPathHopLastChange indicates the sysUpTime when this row was last modified. |
| TMN vRtrGmplsPathHopNodeId | 1.3.6.1.4.1.6527.3.1.2.97.7.1.4 | TmnxGmplsRouterId | read-create | The value of vRtrGmplsPathHopNodeId specifies a 32-bit unique node identifier for the Path Hop entry. |
| U32 vRtrGmplsPathHopTeLinkId | 1.3.6.1.4.1.6527.3.1.2.97.7.1.5 | Unsigned32 | read-create | The value of vRtrGmplsPathHopTeLinkId specifies the te-link id associated with this Path Hop entry. |
| INT vRtrGmplsPathHopStrictOrLoose | 1.3.6.1.4.1.6527.3.1.2.97.7.1.6 | INTEGER | read-create | The value of vRtrGmplsPathHopStrictOrLoose specifies whether this path hop is routed in a strict or loose fashion. |
| TIM vRtrGmplsPeerTblLastChanged | 1.3.6.1.4.1.6527.3.1.2.97.8 | TimeStamp | read-only | The value of vRtrGmplsPeerTblLastChanged indicates the sysUpTime at the time of the last modification to vRtrGmplsPeerTable by adding, deleting an entry or change to a writable object in the table. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value. |
| vRtrGmplsPeerTable | 1.3.6.1.4.1.6527.3.1.2.97.9 | not-accessible | The vRtrGmplsPeerTable is used to indicate the neighbor peer(s) to which control channels may be established. | |
| vRtrGmplsPeerEntry | 1.3.6.1.4.1.6527.3.1.2.97.9.1 | not-accessible | The vRtrGmplsPeerEntry contains an entry that is created for every pair of peer that can establish control channels. | |
| ROW vRtrGmplsPeerRowStatus | 1.3.6.1.4.1.6527.3.1.2.97.9.1.1 | RowStatus | read-create | The value of vRtrGmplsPeerRowStatus specifies the row status used for creation, deletion, or control of vRtrGmplsPeerTable entries. |
| TIM vRtrGmplsPeerLastChange | 1.3.6.1.4.1.6527.3.1.2.97.9.1.2 | TimeStamp | read-only | The value of vRtrGmplsPeerLastChange indicates the sysUpTime when this row was last modified. |
| U32 vRtrGmplsPeerHelloInterval | 1.3.6.1.4.1.6527.3.1.2.97.9.1.3 | Unsigned32 | read-create | The value of vRtrGmplsPeerHelloInterval specifies the length of time in milliseconds, between the hello packets that the router sends on the interface. When the value of vRtrGmplsPeerHelloInterval is set to 0, the sending of hello messages is disabled. |
| TMN vRtrGmplsPeerAdminState | 1.3.6.1.4.1.6527.3.1.2.97.9.1.4 | TmnxAdminState | read-create | The value of vRtrGmplsPeerAdminState specifies the desired administrative state for this Peer. |
| TMN vRtrGmplsPeerOperState | 1.3.6.1.4.1.6527.3.1.2.97.9.1.5 | TmnxOperState | read-only | The value of vRtrGmplsPeerOperState indicates the current operational state for this GMPLS Peer. |
| INT vRtrGmplsPeerOperDownReason | 1.3.6.1.4.1.6527.3.1.2.97.9.1.6 | INTEGER | read-only | The value of vRtrGmplsPeerOperDownReason indicates the operational down reason for the GMPLS peer. |
| NUM vRtrGmplsPeerLastOperChange | 1.3.6.1.4.1.6527.3.1.2.97.9.1.7 | TimeInterval | read-only | The value of vRtrGmplsPeerLastOperChange indicates the time interval which has elapsed since the GMPLS peer's operational state last changed. |
| TMN vRtrGmplsPeerHelloState | 1.3.6.1.4.1.6527.3.1.2.97.9.1.8 | TmnxOperState | read-only | The value of vRtrGmplsPeerHelloState indicates the hello state for this GMPLS peer. |
| U32 vRtrGmplsPeerSourceInstance | 1.3.6.1.4.1.6527.3.1.2.97.9.1.9 | Unsigned32 | read-only | The value of vRtrGmplsPeerSourceInstance indicates the source instance for this GMPLS peer. |
| U32 vRtrGmplsPeerDestInstance | 1.3.6.1.4.1.6527.3.1.2.97.9.1.10 | Unsigned32 | read-only | The value of vRtrGmplsPeerDestInstance indicates the destination instance for this GMPLS peer. |
| C32 vRtrGmplsPeerHelloTimeoutCountEx | 1.3.6.1.4.1.6527.3.1.2.97.9.1.11 | Counter32 | read-only | The value of vRtrGmplsPeerHelloTimeoutCount indicates number of times the Hello timeout timer expired for the peer. |
| C32 vRtrGmplsPeerInstMismatchCount | 1.3.6.1.4.1.6527.3.1.2.97.9.1.12 | Counter32 | read-only | The value of vRtrGmplsPeerInstMismatchCount indicates number of times the source and destination instances received in a Hello message did not match the destination and source instance for this GMPLS peer. |
| IPt vRtrGmplsPeerDestIpAddrType | 1.3.6.1.4.1.6527.3.1.2.97.9.1.13 | InetAddressType | read-only | The value of vRtrGmplsPeerDestIpAddrType indicates the address type of vRtrGmplsPeerDestIpAddr. |
| IP vRtrGmplsPeerDestIpAddr | 1.3.6.1.4.1.6527.3.1.2.97.9.1.14 | InetAddress | read-only | The value of vRtrGmplsPeerDestIpAddr indicates the destination ip address of this GMPLS Peer. |
| IPt vRtrGmplsPeerNextHopIpAddrType | 1.3.6.1.4.1.6527.3.1.2.97.9.1.15 | InetAddressType | read-only | The value of vRtrGmplsPeerNextHopIpAddrType indicates the address type of vRtrGmplsPeerNextHopIpAddr. |
| IP vRtrGmplsPeerNextHopIpAddr | 1.3.6.1.4.1.6527.3.1.2.97.9.1.16 | InetAddress | read-only | The value of vRtrGmplsPeerNextHopIpAddr indicates the next-hop address for this GMPLS Peer. |
| U32 vRtrGmplsPeerIfIndex | 1.3.6.1.4.1.6527.3.1.2.97.9.1.17 | Unsigned32 | read-only | The value of vRtrGmplsPeerIfIndex indicates the interface index associated with vRtrGmplsPeerNextHopIpAddr for this GMPLS Peer. |
| TMN vRtrGmplsPeerNHOperState | 1.3.6.1.4.1.6527.3.1.2.97.9.1.18 | TmnxOperState | read-only | The value of vRtrGmplsPeerNHOperState indicates the next-hop operational state for this peer. |
| U32 vRtrGmplsPeerMTU | 1.3.6.1.4.1.6527.3.1.2.97.9.1.19 | Unsigned32 | read-only | The value of vRtrGmplsPeerMTU indicates the maximum transmission unit allowed for this peer. |
| U32 vRtrGmplsPeerNHChangedCnt | 1.3.6.1.4.1.6527.3.1.2.97.9.1.20 | Unsigned32 | read-only | The value of vRtrGmplsPeerNHChangedCnt indicates the number of changes in active next-hop address. |
| U32 vRtrGmplsPeerGrRestartTime | 1.3.6.1.4.1.6527.3.1.2.97.9.1.21 | Unsigned32 | read-only | The value of vRtrGmplsPeerGrRestartTime indicates the restart time required for the peer to change its operational state from outOfService to inService. |
| U32 vRtrGmplsPeerGrRecoveryTime | 1.3.6.1.4.1.6527.3.1.2.97.9.1.22 | Unsigned32 | read-only | The value of vRtrGmplsPeerGrRecoveryTime indicates the recovery time required for the peer to recover from operationally down state. |
| C32 vRtrGmplsPeerGrInvokedCount | 1.3.6.1.4.1.6527.3.1.2.97.9.1.23 | Counter32 | read-only | The value of vRtrGmplsPeerGrInvokedCount indicates the total number of times Graceful Restart helper procedure has been invoked for this peer. |
| T/F vRtrGmplsPeerGrRestartCap | 1.3.6.1.4.1.6527.3.1.2.97.9.1.24 | TruthValue | read-only | The value of vRtrGmplsPeerGrRestartCap indicates whether or not the neighbor supports graceful restart. |
| INT vRtrGmplsPeerGrState | 1.3.6.1.4.1.6527.3.1.2.97.9.1.25 | INTEGER | read-only | The value of vRtrGmplsPeerGrState indicates the current state of the peer after loss of communication. none - phase info not available. restartInProg - indicates restart phase is in progress recoveryInProg - indicates recovery phase is in progress cleanup - indicates cleanup in progress. |
| U32 vRtrGmplsPeerGrHelperTimeRem | 1.3.6.1.4.1.6527.3.1.2.97.9.1.26 | Unsigned32 | read-only | The value of vRtrGmplsPeerGrHelperTimeRem indicates the amount of time remaining in seconds, for the restart phase or recovery phase to timeout. If the timer expires, the RSVP session not recovered will be torn down. |
| BIT vRtrGmplsPeerFlags | 1.3.6.1.4.1.6527.3.1.2.97.9.1.27 | Bits | read-only | The value of vRtrGmplsPeerFlags indicates the set of properties for this GMPLS peer. The bits are defined as follows : localRefreshReduction - If set, implies that refresh reduction is configured locally for this peer. localReliableDelivery - If set, implies that reliable delivery is configured locally for this peer. remoteRefreshReduction - If set, implies that the refresh reduction is supported on the remote end. remoteMessageId - If set, implies that message ID object is supported on the remote end. localGrHelper - If set, implies that Graceful Restart Helper mode is enabled locally for this peer. |
| U32 vRtrGmplsPeerSrefreshTimeRem | 1.3.6.1.4.1.6527.3.1.2.97.9.1.28 | Unsigned32 | read-only | The value of vRtrGmplsPeerSrefreshTimeRem indicates the time remaining in the Srefresh timer. An Srefresh message is sent when this timer expires. |
| U32 vRtrGmplsPeerEpochNum | 1.3.6.1.4.1.6527.3.1.2.97.9.1.29 | Unsigned32 | read-only | The value of vRtrGmplsPeerEpochNum indicates the epoch number received from the peer. |
| U32 vRtrGmplsPeerMaxMsgId | 1.3.6.1.4.1.6527.3.1.2.97.9.1.30 | Unsigned32 | read-only | The value of vRtrGmplsPeerMaxMsgId indicates the highest message ID received from this peer. |
| C32 vRtrGmplsPeerOutofOrderMsgs | 1.3.6.1.4.1.6527.3.1.2.97.9.1.31 | Counter32 | read-only | The value of vRtrGmplsPeerOutofOrderMsgs indicates the number of out of order messages received from this peer. |
| C32 vRtrGmplsPeerRetransmittedMsgs | 1.3.6.1.4.1.6527.3.1.2.97.9.1.32 | Counter32 | read-only | The value of vRtrGmplsPeerRetransmittedMsgs indicates the number of times messages have been retransmitted to the peer because the peer did not acknowledge that it received the message. |
| G32 vRtrGmplsPeerDnStreamSessCnt | 1.3.6.1.4.1.6527.3.1.2.97.9.1.33 | Gauge32 | read-only | The value of vRtrGmplsPeerDnStreamSessCnt indicates the number of session associated with this peer which are currently down. |
| G32 vRtrGmplsPeerUpStreamSessCnt | 1.3.6.1.4.1.6527.3.1.2.97.9.1.34 | Gauge32 | read-only | The value of vRtrGmplsPeerUpStreamSessCnt indicates the number of session associated with this peer which are currently up. |
| C32 vRtrGmplsPeerPathTimeouts | 1.3.6.1.4.1.6527.3.1.2.97.9.1.35 | Counter32 | read-only | The value of vRtrGmplsPeerPathTimeouts indicates the number of PATH message timeout for this peer. |
| C32 vRtrGmplsPeerResvTimeouts | 1.3.6.1.4.1.6527.3.1.2.97.9.1.36 | Counter32 | read-only | The value of vRtrGmplsPeerResvTimeouts indicates the number of RESV message timeout for this peer. |
| U32 vRtrGmplsPeerLspHoldTimer | 1.3.6.1.4.1.6527.3.1.2.97.9.1.37 | Unsigned32 | read-create | The value of vRtrGmplsPeerLspHoldTimer specifies the time, in seconds, that the software waits after a session for this peer to become operationally up before activating data transmission on the session. |
| TIM vRtrGmplsLspTblLastChanged | 1.3.6.1.4.1.6527.3.1.2.97.10 | TimeStamp | read-only | The value of vRtrGmplsLspTblLastChanged indicates the sysUpTime at the time of the last modification to vRtrGmplsLspTable by adding, deleting an entry or change to a writable object in the table. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value. |
| vRtrGmplsLspTable | 1.3.6.1.4.1.6527.3.1.2.97.11 | not-accessible | The vRtrGmplsLspTable is used to indicate entry for each Labeled Switch Path (LSP) configured for a virtual router in the system. | |
| vRtrGmplsLspEntry | 1.3.6.1.4.1.6527.3.1.2.97.11.1 | not-accessible | Each row entry in vRtrGmplsLspEntry represents a Labeled Switch Path (LSP) configured for a virtual router in the system. Entries can be created and deleted via SNMP SET operations. Setting RowStatus to 'active' requires vRtrGmplsLspName to have been assigned a valid value. | |
| U32 vRtrGmplsLspIndex | 1.3.6.1.4.1.6527.3.1.2.97.11.1.1 | Unsigned32 | not-accessible | The value of vRtrGmplsLspIndex indicates the unique value which identifies the GMPLS Labeled Switch Path (LSP) for this virtual router in the Nokia SROS system. It is a unique value among entries with the same value of vRtrID. |
| ROW vRtrGmplsLspRowStatus | 1.3.6.1.4.1.6527.3.1.2.97.11.1.2 | RowStatus | read-create | The value of vRtrGmplsLspRowStatus specifies the row status used for creation, deletion, or control of vRtrGmplsLspTable entries. |
| TIM vRtrGmplsLspLastChange | 1.3.6.1.4.1.6527.3.1.2.97.11.1.3 | TimeStamp | read-only | The value of vRtrGmplsLspLastChange indicates the sysUpTime when this row was last modified. |
| TNA vRtrGmplsLspName | 1.3.6.1.4.1.6527.3.1.2.97.11.1.4 | TNamedItemOrEmpty | read-create | The value of vRtrGmplsLspName specifies the name for this Labeled Switch Path. The vRtrGmplsLspName must be unique within a virtual router instance. The value of vRtrGmplsLspName needs to be set at row creation time. |
| INT vRtrGmplsLspType | 1.3.6.1.4.1.6527.3.1.2.97.11.1.5 | INTEGER | read-create | The value of vRtrGmplsLspType specifies the type of GMPLS Labeled Switch Path (LSP). When the value of vRtrGmplsLspType is 'gmplsUni' it indicates that the Labeled Switch Path (LSP) is an RSVP signalled GMPLS LSP. The value of vRtrGmplsLspType needs to be set at row creation time. |
| TMN vRtrGmplsLspAdminState | 1.3.6.1.4.1.6527.3.1.2.97.11.1.6 | TmnxAdminState | read-create | The value of vRtrGmplsLspAdminState specifies the desired administrative state for this GMPLS Labeled Switch Path (LSP). |
| TMN vRtrGmplsLspOperState | 1.3.6.1.4.1.6527.3.1.2.97.11.1.7 | TmnxOperState | read-only | The value of vRtrGmplsLspOperState indicates the current operational state of this GMPLS Labeled Switch Path (LSP). |
| INT vRtrGmplsLspSwitchingType | 1.3.6.1.4.1.6527.3.1.2.97.11.1.8 | INTEGER | read-create | The value of vRtrGmplsLspSwitchingType specifies the type of switching that should be performed on a particular link. |
| INT vRtrGmplsLspEncodingType | 1.3.6.1.4.1.6527.3.1.2.97.11.1.9 | INTEGER | read-create | The value of vRtrGmplsLspEncodingType specifies the encoding type of the payload carried by the GMPLS Label Switch Path (LSP). |
| INT vRtrGmplsLspGeneralizedPid | 1.3.6.1.4.1.6527.3.1.2.97.11.1.10 | INTEGER | read-create | The value of vRtrGmplsLspGeneralizedPid specifies the type of payload carried by the GMPLS LSP. |
| INT vRtrGmplsLspE2EProtection | 1.3.6.1.4.1.6527.3.1.2.97.11.1.11 | INTEGER | read-create | The value of vRtrGmplsLspE2EProtection specifies the end to end protection type for this GMPLS LSP. When the value of vRtrGmplsLspE2EProtection is set to 'unprotected', the GMPLS LSP is not protected. The GMPLS LSP is a single working path. A protect path cannot be configured. When the value of vRtrGmplsLspE2EProtection is set to 'oneToN', a single protect path protects the working paths of one or more GMPLS LSPs. When the value of vRtrGmplsLspE2EProtection is set to 'sbr', full LSP rerouting is allowed for a failed working path. |
| U32 vRtrGmplsLspRevertTimer | 1.3.6.1.4.1.6527.3.1.2.97.11.1.12 | Unsigned32 | read-create | The value of vRtrGmplsLspRevertTimer specifies a revert timer for a Labeled Switch Path (LSP). The Labeled Switch Path (LSP) will be switched to the primary path only after the revert interval is over. When the value of vRtrGmplsLspRevertTimer is set to '0', the LSP will revert immediately. |
| U32 vRtrGmplsLspRetryLimit | 1.3.6.1.4.1.6527.3.1.2.97.11.1.13 | Unsigned32 | read-create | The value of vRtrGmplsLspRetryLimit specifies the maximum number of attempts the software should make to establish an LSP. A value of zero(0) specifies that an infinite number of retry attempts should be made. |
| U32 vRtrGmplsLspRetryTimer | 1.3.6.1.4.1.6527.3.1.2.97.11.1.14 | Unsigned32 | read-create | The value of vRtrGmplsLspRetryTimer specifies the time in seconds the software will wait before attempting to establish the failed LSP. |
| IPt vRtrGmplsLspToAddrType | 1.3.6.1.4.1.6527.3.1.2.97.11.1.15 | InetAddressType | read-create | The value of vRtrGmplsLspToAddrType specifies the destination address type of the Labeled Switch Path (LSP). |
| IP vRtrGmplsLspToAddr | 1.3.6.1.4.1.6527.3.1.2.97.11.1.16 | InetAddress | read-create | The value of vRtrGmplsLspToAddr specifies the destination address of this LSP. |
| G32 vRtrGmplsLspNumWorkingPath | 1.3.6.1.4.1.6527.3.1.2.97.11.1.17 | Gauge32 | read-only | The value of vRtrGmplsLspNumWorkingPath indicates the total number of working-paths for this GMPLS Labeled Switch Path (LSP). |
| G32 vRtrGmplsLspNumProtectPath | 1.3.6.1.4.1.6527.3.1.2.97.11.1.18 | Gauge32 | read-only | The value of vRtrGmplsLspNumProtectPath indicates the total number of protect-paths for this GMPLS Labeled Switch Path (LSP). |
| G32 vRtrGmplsLspNumWorkingPathUp | 1.3.6.1.4.1.6527.3.1.2.97.11.1.19 | Gauge32 | read-only | The value of vRtrGmplsLspNumWorkingPathUp indicates the total number of working-paths that are operationally up for this GMPLS Labeled Switch Path (LSP). |
| G32 vRtrGmplsLspNumProtectPathUp | 1.3.6.1.4.1.6527.3.1.2.97.11.1.20 | Gauge32 | read-only | The value of vRtrGmplsLspNumProtectPathUp indicates the total number of protect-paths that are operationally up for this GMPLS Labeled Switch Path (LSP). |
| NUM vRtrGmplsLspLastOperChange | 1.3.6.1.4.1.6527.3.1.2.97.11.1.21 | TimeInterval | read-only | The value of vRtrGmplsLspLastOperChange indicates the time interval which has elapsed since the GMPLS LSP's operational state last changed. |
| TIM vRtrGmplsLspPathTblLastChanged | 1.3.6.1.4.1.6527.3.1.2.97.12 | TimeStamp | read-only | The value of vRtrGmplsLspPathTblLastChanged indicates the sysUpTime at the time of the last modification to vRtrGmplsLspPathTable by adding, deleting an entry or change to a writable object in the table. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value. |
| vRtrGmplsLspPathTable | 1.3.6.1.4.1.6527.3.1.2.97.13 | not-accessible | The vRtrGmplsLspPathTable is used to indicate entry for each LSP Path configured for a virtual router in the system. | |
| vRtrGmplsLspPathEntry | 1.3.6.1.4.1.6527.3.1.2.97.13.1 | not-accessible | Each row entry in vRtrGmplsLspPathEntry represents a protecting or a working path configured corresponding to a LSP for a virtual router in the system. Entries can be created and deleted via SNMP SET operations. | |
| INT vRtrGmplsLspPathType | 1.3.6.1.4.1.6527.3.1.2.97.13.1.1 | INTEGER | not-accessible | The value of vRtrGmplsLspPathType specifies the path type for the GMPLS LSP path. When the value of vRtrGmplsLspPathType is set to 'working', the path is used a primary path for the LSP. When the value of vRtrGmplsLspPathType is set to 'protecting', the path is used as a secondary path for the LSP. |
| ROW vRtrGmplsLspPathRowStatus | 1.3.6.1.4.1.6527.3.1.2.97.13.1.2 | RowStatus | read-create | The value of vRtrGmplsLspPathRowStatus specifies the row status used for creation, deletion, or control of vRtrGmplsLspPathTable entries. |
| TIM vRtrGmplsLspPathLastChangedTime | 1.3.6.1.4.1.6527.3.1.2.97.13.1.3 | TimeStamp | read-only | The value of vRtrGmplsLspPathLastChangedTime indicates the last time, since system startup, that a writable object in this table was modified. |
| TMN vRtrGmplsLspPathAdminState | 1.3.6.1.4.1.6527.3.1.2.97.13.1.4 | TmnxAdminState | read-create | The value of vRtrGmplsLspPathAdminState specifies the administrative state of the GMPLS LSP Path. |
| TMN vRtrGmplsLspPathOperState | 1.3.6.1.4.1.6527.3.1.2.97.13.1.5 | TmnxGmplsSessionOperState | read-only | The value of vRtrGmplsLspPathOperState indicates the operational state of the GMPLS LSP Path. |
| TMN vRtrGmplsLspPathBWSignalType | 1.3.6.1.4.1.6527.3.1.2.97.13.1.6 | TmnxGmplsSessionBWSignalType | read-create | The value of vRtrGmplsLspPathBWSignalType specifies the bandwith associated with this GMPLS LSP path. The bit-rate and values corresponding to the signal-type are : Signal Type (Bit-rate) Value (Bytes/Sec) (IEEE Floating point) -------------- --------------- --------------------- DS0 (0.064 Mbps) 0x45FA0000 DS1 (1.544 Mbps) 0x483C7A00 E1 (2.048 Mbps) 0x487A0000 DS2 (6.312 Mbps) 0x4940A080 E2 (8.448 Mbps) 0x4980E800 Ethernet (10.00 Mbps) 0x49989680 E3 (34.368 Mbps) 0x4A831A80 DS3 (44.736 Mbps) 0x4AAAA780 STS-1 (51.84 Mbps) 0x4AC5C100 Fast Ethernet (100.00 Mbps) 0x4B3EBC20 E4 (139.264 Mbps) 0x4B84D000 FC-0 133M 0x4B7DAD68 OC-3/STM-1 (155.52 Mbps) 0x4B9450C0 FC-0 266M 0x4BFDAD68 FC-0 531M 0x4C7D3356 OC-12/STM-4 (622.08 Mbps) 0x4C9450C0 GigE (1000.00 Mbps) 0x4CEE6B28 FC-0 1062M 0x4CFD3356 OC-48/STM-16 (2488.32 Mbps) 0x4D9450C0 OC-192/STM-64 (9953.28 Mbps) 0x4E9450C0 10GigE-LAN (10000.00 Mbps) 0x4E9502F9 OC-768/STM-256 (39813.12 Mbps) 0x4F9450C0 |
| INT vRtrGmplsLspPathSegProtType | 1.3.6.1.4.1.6527.3.1.2.97.13.1.7 | INTEGER | read-create | The value of vRtrGmplsLspPathSegProtType specifies the segment protection type for this GMPLS LSP path. When the value of vRtrGmplsLspPathSegProtType is set to 'unprotected', the GMPLS LSP path is not protected against any failures. When the value of vRtrGmplsLspPathSegProtType is set to 'sbr' (source based reroute), a path will be restored after a failure. When the value of vRtrGmplsLspPathSegProtType is set to 'gr' (guaranteed restoration), a shared backup is assigned to the path, and recovery resources are reserved. When the value of vRtrGmplsLspPathSegProtType is set to 'sncp' (sub-network connection protection), it provides a 50ms protection in case of a single failure. When the value of vRtrGmplsLspPathSegProtType is set to 'prc' (path restoration combined), it provides a 50ms protection even in the case of multiple failures. |
| U32 vRtrGmplsLspPathLspId | 1.3.6.1.4.1.6527.3.1.2.97.13.1.8 | Unsigned32 | read-only | The value of vRtrGmplsLspPathLspId indicates the LSP ID for the GMPLS LSP Path. When the value is set to '0' it indicates that there is no LSP ID assigned for this LSP Path. |
| U32 vRtrGmplsLspPathPeerNodeId | 1.3.6.1.4.1.6527.3.1.2.97.13.1.9 | Unsigned32 | read-create | The value of vRtrGmplsLspPathPeerNodeId specifies the unique peer node identifier to be used for signalling the GMPLS LSP Path. |
| U32 vRtrGmplsLspPathRetryAttempts | 1.3.6.1.4.1.6527.3.1.2.97.13.1.10 | Unsigned32 | read-only | The value of vRtrGmplsLspPathRetryAttempts indicates the total number of signalling attempts that have been made to change the operational state for this LSP Path to inService. |
| IPt vRtrGmplsLspPathFailNodeAddrType | 1.3.6.1.4.1.6527.3.1.2.97.13.1.11 | InetAddressType | read-only | The value vRtrGmplsLspPathFailNodeAddrType indicates the address type for vRtrGmplsLspPathFailNodeAddr. |
| IP vRtrGmplsLspPathFailNodeAddr | 1.3.6.1.4.1.6527.3.1.2.97.13.1.12 | InetAddress | read-only | The value of vRtrGmplsLspPathFailNodeAddr indicates the address of the node at which this GMPLS LSP Path failed. When no failure has occurred, this value is 0. |
| TMN vRtrGmplsLspPathFailCode | 1.3.6.1.4.1.6527.3.1.2.97.13.1.13 | TmnxGmplsLspPathFailCode | read-only | The value of vRtrGmplsLspPathFailCode indicates the reason for which this GMPLS LSP Path failed. A value of 0 indicates that no failure has occurred. |
| U32 vRtrGmplsLspPathNextRetryIn | 1.3.6.1.4.1.6527.3.1.2.97.13.1.14 | Unsigned32 | read-only | The value of vRtrGmplsLspPathNextRetryIn indicates the time remaining in seconds before the next retry for this GMPLS LSP Path is attempted. |
| U32 vRtrGmplsLspPathTimeoutIn | 1.3.6.1.4.1.6527.3.1.2.97.13.1.15 | Unsigned32 | read-only | The value of vRtrGmplsLspPathTimeoutIn indicates the amount of time in seconds the software waits for an LSP Path to come up after sending out the initial PATH message. If the timer expires and the LSP path is not operationally up, it is torn down and the LSP retry timer is started to schedule a new retry cycle. |
| U32 vRtrGmplsLspPathARHopListIndex | 1.3.6.1.4.1.6527.3.1.2.97.13.1.16 | Unsigned32 | read-only | The value of vRtrGmplsLspPathARHopListIndex indicates the primary index into the vRtrGmplsARHopTable identifying the actual hop list recorded for the LSP Path. A value of 0 implies that there is no recorded hop list associated with this LSP path. |
| NUM vRtrGmplsLspPathLastOperChange | 1.3.6.1.4.1.6527.3.1.2.97.13.1.17 | TimeInterval | read-only | The value of vRtrGmplsLspPathLastOperChange indicates the time interval which has elapsed since the GMPLS LSP Path's operational state last changed. |
| TIM tmnxGmplsTunGrpTableLastChanged | 1.3.6.1.4.1.6527.3.1.2.97.14 | TimeStamp | read-only | The tmnxGmplsTunGrpTableLastChanged indicates the time, since system startup, when tmnxGmplsTunGrpEntry last changed configuration. |
| tmnxGmplsTunGrpTable | 1.3.6.1.4.1.6527.3.1.2.97.15 | not-accessible | The tmnxGmplsTunGrpTable consists of the GMPLS Tunnel Group configuration information. | |
| tmnxGmplsTunGrpEntry | 1.3.6.1.4.1.6527.3.1.2.97.15.1 | not-accessible | The tmnxGmplsTunGrpEntry contains information pertaining to an individual GMPLS Tunnel Group. Rows in this table are created and destroyed using the tmnxGmplsTunGrpRowStatus object. A corresponding row in the tmnxPortTable will exist for each row in this table, based on tmnxGmplsTunGrpIfIndex. The tmnxPortEntry corresponding to this entry manages the administration, description, MAC address and other port related configuration. | |
| U32 tmnxGmplsTunGrpId | 1.3.6.1.4.1.6527.3.1.2.97.15.1.1 | Unsigned32 | not-accessible | The value of tmnxGmplsTunGrpId specifies a unique identifier for this GMPLS Tunnel Group. tmnxGmplsTunGrpId and tmnxEthTunnelIndex share the same number space and must be unique. For example, if a GMPLS Tunnel Group exists with tmnxGmplsTunGrpId = 1, an Ethernet Tunnel cannot be created with tmnxEthTunnelIndex = 1. |
| ROW tmnxGmplsTunGrpRowStatus | 1.3.6.1.4.1.6527.3.1.2.97.15.1.2 | RowStatus | read-create | The value of tmnxGmplsTunGrpRowStatus specifies the row status. It allows the creation and deletion of rows in tmnxGmplsTunGrpTable. A corresponding row in the tmnxPortTable is created by the system when a tmnxGmplsTunGrpRowStatus value of 'createAndGo (4)' is issued on a new row in the tmnxGmplsTunGrpTable. The corresponding row in the tmnxPortTable will be destroyed by the system when the tmnxGmplsTunGrpRowStatus value of 'destroy (6)' is issued. |
| TIM tmnxGmplsTunGrpLastChanged | 1.3.6.1.4.1.6527.3.1.2.97.15.1.3 | TimeStamp | read-only | The value of tmnxGmplsTunGrpLastChanged indicates the time, since system startup, that the configuration of this GMPLS Tunnel Group was created or modified. |
| INT tmnxGmplsTunGrpType | 1.3.6.1.4.1.6527.3.1.2.97.15.1.4 | INTEGER | read-create | The value of tmnxGmplsTunGrpType specifies the GMPLS Tunnel Group type. Code points: headEnd (1) - the head end of the GMPLS tunnel group (ingress node endpoint) tailEnd (2) - the tail end of the GMPLS tunnel group (egress node endpoint) |
| INT tmnxGmplsTunGrpMode | 1.3.6.1.4.1.6527.3.1.2.97.15.1.5 | INTEGER | read-create | The value of tmnxGmplsTunGrpMode specifies the mode of the GMPLS Tunnel Group. Code points: activeStandby (1) - only 1 member can be configured, with tmnxGmplsTunGrpMemberId = 1 - the member gLSP can be either unprotected (with only working-path) or protected (working-path and protection-path) - only one member path can be active at a time loadSharing (2) - maximum of 16 members can be configured - the member gLSP must be unprotected (with only working-path) - multiple member paths can be active at a time |
| IPt tmnxGmplsTunGrpFarEndAddrType | 1.3.6.1.4.1.6527.3.1.2.97.15.1.6 | InetAddressType | read-create | The value of tmnxGmplsTunGrpFarEndAddrType specifies the address type of tmnxGmplsTunGrpFarEndAddress. |
| IP tmnxGmplsTunGrpFarEndAddress | 1.3.6.1.4.1.6527.3.1.2.97.15.1.7 | InetAddress | read-create | The value of tmnxGmplsTunGrpFarEndAddress specifies the far-end address of this GMPLS Tunnel Group. If the value of tmnxGmplsTunGrpType is 'head-end(1)', this object represents the address of the receiver. If the value of tmnxGmplsTunGrpType is 'tail-end(1)', this object represents the address of the sender. |
| TMN tmnxGmplsTunGrpIfIndex | 1.3.6.1.4.1.6527.3.1.2.97.15.1.8 | TmnxPortID | read-only | The value of tmnxGmplsTunGrpIfIndex indicates the tmnxPortPortID for the GMPLS Tunnel Group. |
| TMN tmnxGmplsTunGrpActiveMembers | 1.3.6.1.4.1.6527.3.1.2.97.15.1.9 | TmnxGmplsTunGrpMemberList | read-only | The value of tmnxGmplsTunGrpActiveMembers indicates which members are actively receiving and transmitting data for this GMPLS Tunnel Group. |
| U32 tmnxGmplsTunGrpMemberThreshold | 1.3.6.1.4.1.6527.3.1.2.97.15.1.10 | Unsigned32 | read-create | The value of tmnxGmplsTunGrpMemberThreshold specifies the threshold for the GMPLS Tunnel Group. This object is only valid when tmnxGmplsTunGrpMode is set to 'loadSharing (2)'. When a member's operational state changes and the number of operational members is less than or equal to tmnxGmplsTunGrpMemberThreshold, the GMPLS Tunnel Group is set operationally down. When the number of operational members become greater than tmnxGmplsTunGrpMemberThreshold, the GMPLS Tunnel Group is set operationally up. The value of zero specifies to bring the GMPLS Tunnel Group operationally down only when all members are operationally down, and bring the GMPLS Tunnel Group operationally up when at least one member is operationally up. |
| TIM tmnxGmplsTunGrpMemTblLastChanged | 1.3.6.1.4.1.6527.3.1.2.97.16 | TimeStamp | read-only | The tmnxGmplsTunGrpMemTblLastChanged indicates the time, since system startup, when tmnxGmplsTunGrpMemberEntry last changed configuration. |
| tmnxGmplsTunGrpMemberTable | 1.3.6.1.4.1.6527.3.1.2.97.17 | not-accessible | The tmnxGmplsTunGrpMemberTable consists of the members associated with the corresponding tmnxGmplsTunGrpEntry. | |
| tmnxGmplsTunGrpMemberEntry | 1.3.6.1.4.1.6527.3.1.2.97.17.1 | not-accessible | The tmnxGmplsTunGrpMemberEntry contains information pertaining to an individual member interface associated with a tmnxGmplsTunGrpEntry. Rows in this table are created and destroyed using the tmnxGmplsTunGrpMemberRowStatus object. | |
| U32 tmnxGmplsTunGrpMemberId | 1.3.6.1.4.1.6527.3.1.2.97.17.1.1 | Unsigned32 | not-accessible | The value of tmnxGmplsTunGrpMemberId specifies a unique identifier for this member in the given GMPLS Tunnel Group. When the value of tmnxGmplsTunGrpMode is 'activeStandby (1)', only a value of 1 is supported for this object. |
| ROW tmnxGmplsTunGrpMemberRowStatus | 1.3.6.1.4.1.6527.3.1.2.97.17.1.2 | RowStatus | read-create | The tmnxGmplsTunGrpMemberRowStatus controls the creation and deletion of rows in the tmnxGmplsTunGrpMemberTable. |
| TIM tmnxGmplsTunGrpMemberLastChanged | 1.3.6.1.4.1.6527.3.1.2.97.17.1.3 | TimeStamp | read-only | The value of tmnxGmplsTunGrpMemberLastChanged indicates the time, since system startup, that the configuration of this member was created or modified. |
| TMN tmnxGmplsTunGrpMemberAdminStatus | 1.3.6.1.4.1.6527.3.1.2.97.17.1.4 | TmnxAdminState | read-create | The value of tmnxGmplsTunGrpMemberAdminStatus specifies the administrative status of this member. |
| TMN tmnxGmplsTunGrpMemberOperStatus | 1.3.6.1.4.1.6527.3.1.2.97.17.1.5 | TmnxOperState | read-only | The value of tmnxGmplsTunGrpMemberOperStatus indicates the operational status of this member. |
| TIT tmnxGmplsTunGrpMemberGlspSesName | 1.3.6.1.4.1.6527.3.1.2.97.17.1.6 | TItemDescription | read-create | The value of tmnxGmplsTunGrpMemberGlspSesName specifies the GMPLS LSP working path's session name of this member. This object is only valid for LSPs where the vRtrGmplsLspPathType is set to 'working (1)'. |
| BIT tmnxGmplsTunGrpMemberRsnDnFlgs | 1.3.6.1.4.1.6527.3.1.2.97.17.1.7 | Bits | read-only | The value of tmnxGmplsTunGrpMemberRsnDnFlgs indicates the reason(s) why this member is operationally down. The recognized BIT values are: unknown (0) - unspecified or unknown adminDn (1) - the member or related GMPLS tunnel group is administratively down wpLspDn (2) - the associated working LSP path is operationally down wpPortDn (3) - the DB link port associated with the working LSP path is operationally down wpPortNoRsrc (4) - the DB link port associated with the working LSP path does not have enough resources to support the services over the logical port of the GMPLS tunnel group ppLspDn (5) - the associated protect LSP path is operationally down ppPortDn (6) - the DB link port associated with the protect LSP path is operationally down ppPortNoRsrc (7) - the DB link port associated with the protect LSP path does not have enough resources to support the services over the logical port of the GMPLS tunnel group |
| TMN tmnxGmplsTunGrpMemberWpIfIndex | 1.3.6.1.4.1.6527.3.1.2.97.17.1.8 | TmnxPortID | read-only | The value of tmnxGmplsTunGrpMemberWpIfIndex indicates the tmnxPortPortID for the working path of the member. |
| TMN tmnxGmplsTunGrpMemberPpIfIndex | 1.3.6.1.4.1.6527.3.1.2.97.17.1.9 | TmnxPortID | read-only | The value of tmnxGmplsTunGrpMemberPpIfIndex indicates the tmnxPortPortID for the protect path of the member. This object is only valid for GMPLS tunnel groups with tmnxGmplsTunGrpMode set to 'activeStandby (2)'. |
| TIM vRtrGmplsTeLinkTblLastChanged | 1.3.6.1.4.1.6527.3.1.2.97.18 | TimeStamp | read-only | The value of vRtrGmplsTeLinkTblLastChanged indicates the sysUpTime at the time of the last modification to vRtrGmplsTeLinkTable by adding, deleting an entry or change to a writable object in the table. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value. |
| vRtrGmplsTeLinkTable | 1.3.6.1.4.1.6527.3.1.2.97.19 | not-accessible | The vRtrGmplsTeLinkTable is used to indicate entry for each Traffic Engineering (TE) Link configured for a virtual router in the system. | |
| vRtrGmplsTeLinkEntry | 1.3.6.1.4.1.6527.3.1.2.97.19.1 | not-accessible | Each row entry in vRtrGmplsTeLinkEntry represents a TE link on a given virtual router in the system. Entries can be created and deleted via SNMP SET operations. | |
| ROW vRtrGmplsTeLinkRowStatus | 1.3.6.1.4.1.6527.3.1.2.97.19.1.1 | RowStatus | read-create | The value of vRtrGmplsTeLinkRowStatus specifies the row status used for creation, deletion, or control of vRtrGmplsTeLinkTable entries. |
| TIM vRtrGmplsTeLinkLastChanged | 1.3.6.1.4.1.6527.3.1.2.97.19.1.2 | TimeStamp | read-only | The value of vRtrGmplsTeLinkLastChanged indicates the sysUpTime when this row was last modified. |
| TMN vRtrGmplsTeLinkAdminState | 1.3.6.1.4.1.6527.3.1.2.97.19.1.3 | TmnxAdminState | read-create | The value of vRtrGmplsTeLinkAdminState specifies the administrative state of this TE link. |
| TMN vRtrGmplsTeLinkOperState | 1.3.6.1.4.1.6527.3.1.2.97.19.1.4 | TmnxOperState | read-only | The value of vRtrGmplsTeLinkOperState indicates the operational state of this TE link. |
| TIM vRtrGmplsLspPathExSrlgTblLastCh | 1.3.6.1.4.1.6527.3.1.2.97.20 | TimeStamp | read-only | The value of the object vRtrGmplsLspPathExSrlgTblLastCh indicates the time of the last change to any row of vRtrGmplsLspPathExclSrlgTable. |
| vRtrGmplsLspPathExclSrlgTable | 1.3.6.1.4.1.6527.3.1.2.97.21 | not-accessible | The vRtrGmplsLspPathExclSrlgTable table contains the Exclude SRLG groups that are mapped to this GMPLS Lsp Path. | |
| vRtrGmplsLspPathExclSrlgEntry | 1.3.6.1.4.1.6527.3.1.2.97.21.1 | not-accessible | Each row entry represents a mapping between Gmpls LSP Path and an SRLG Group. | |
| ROW vRtrGmplsLspPathExclSrlgRowStat | 1.3.6.1.4.1.6527.3.1.2.97.21.1.1 | RowStatus | read-create | The value of the object vRtrGmplsLspPathExclSrlgRowStat specifies the Row status of this table row. This object is used to create or delete rows in this table. |
| vRtrGmplsGeneralStatTable | 1.3.6.1.4.1.6527.3.1.2.97.22 | not-accessible | The vRtrGmplsGeneralStatTable contains statistics for a GMPLS protocol instance within a virtual router. | |
| vRtrGmplsGeneralStatEntry | 1.3.6.1.4.1.6527.3.1.2.97.22.1 | not-accessible | Each row entry represents a collection of statistics for an instance of the GMPLS protocol running within a virtual router. Entries cannot be created and deleted via SNMP SET operations. | |
| G32 vRtrGmplsGenWorkingPathOriginate | 1.3.6.1.4.1.6527.3.1.2.97.22.1.1 | Gauge32 | read-only | The value of vRtrGmplsGenWorkingPathOriginate indicates the number of working path LSPs that originate at this virtual router. |
| G32 vRtrGmplsGenWorkingPathTerminate | 1.3.6.1.4.1.6527.3.1.2.97.22.1.2 | Gauge32 | read-only | The value of vRtrGmplsGenWorkingPathTerminate indicates the number of working path LSPs that terminate at this virtual router. |
| G32 vRtrGmplsGenProtectPathOriginate | 1.3.6.1.4.1.6527.3.1.2.97.22.1.3 | Gauge32 | read-only | The value of vRtrGmplsGenProtectPathOriginate indicates the number of protect path LSPs that originate at this virtual router. |
| G32 vRtrGmplsGenProtectPathTerminate | 1.3.6.1.4.1.6527.3.1.2.97.22.1.4 | Gauge32 | read-only | The value of vRtrGmplsGenProtectPathTerminate indicates the number of protect path LSPs that terminate at this virtual router. |
| vRtrGmplsPeerStatTable | 1.3.6.1.4.1.6527.3.1.2.97.23 | not-accessible | The vRtrGmplsPeerStatTable contains statistics for GMPLS peer. | |
| vRtrGmplsPeerStatEntry | 1.3.6.1.4.1.6527.3.1.2.97.23.1 | not-accessible | Each row entry represents a collection of statistics for GMPLS peer. Entries cannot be created and deleted via SNMP SET operations. | |
| C64 vRtrGmplsPeerRxBadPktCount | 1.3.6.1.4.1.6527.3.1.2.97.23.1.1 | Counter64 | read-only | The value of vRtrGmplsPeerRxBadPktCount indicates the total number of bad packets received by this GMPLS Peer. |
| C64 vRtrGmplsPeerTxHello | 1.3.6.1.4.1.6527.3.1.2.97.23.1.2 | Counter64 | read-only | The value of vRtrGmplsPeerTxHello indicates the number of RSVP HELLO messages transmitted by this GMPLS Peer. |
| C64 vRtrGmplsPeerRxHello | 1.3.6.1.4.1.6527.3.1.2.97.23.1.3 | Counter64 | read-only | The value of vRtrGmplsPeerRxHello indicates the number of RSVP HELLO messages received by this GMPLS Peer. |
| C64 vRtrGmplsPeerTxPaths | 1.3.6.1.4.1.6527.3.1.2.97.23.1.4 | Counter64 | read-only | The value of vRtrGmplsPeerTxPaths indicates the total number of RSVP PATH messages that have been transmitted by this GMPLS Peer. |
| C64 vRtrGmplsPeerRxPaths | 1.3.6.1.4.1.6527.3.1.2.97.23.1.5 | Counter64 | read-only | The value of vRtrGmplsPeerRxPaths indicates the total number of RSVP PATH messages that have been received by this GMPLS Peer. |
| C64 vRtrGmplsPeerTxPathErr | 1.3.6.1.4.1.6527.3.1.2.97.23.1.6 | Counter64 | read-only | The value of vRtrGmplsPeerTxPathErr indicates the total number of RSVP PATH ERROR messages that have been transmitted by this GMPLS Peer. |
| C64 vRtrGmplsPeerRxPathErr | 1.3.6.1.4.1.6527.3.1.2.97.23.1.7 | Counter64 | read-only | The value of vRtrGmplsPeerRxPathErr indicates the total number of RSVP PATH ERROR messages that have been received by this GMPLS Peer. |
| C64 vRtrGmplsPeerTxPathTear | 1.3.6.1.4.1.6527.3.1.2.97.23.1.8 | Counter64 | read-only | The value of vRtrGmplsPeerTxPathTear indicates the number of RSVP PATH TEAR messages that have been transmitted from this GMPLS Peer. |
| C64 vRtrGmplsPeerRxPathTear | 1.3.6.1.4.1.6527.3.1.2.97.23.1.9 | Counter64 | read-only | The value of vRtrGmplsPeerRxPathTear indicates the number of RSVP PATH TEAR messages that have been received from this GMPLS Peer. |
| C64 vRtrGmplsPeerTxResv | 1.3.6.1.4.1.6527.3.1.2.97.23.1.10 | Counter64 | read-only | The value of vRtrGmplsPeerTxResv indicates the total number of RSVP RESV messages that have been transmitted by this GMPLS Peer. |
| C64 vRtrGmplsPeerRxResv | 1.3.6.1.4.1.6527.3.1.2.97.23.1.11 | Counter64 | read-only | The value of vRtrGmplsPeerRxResv indicates the total number of RSVP RESV messages that have been received by this GMPLS Peer. |
| C64 vRtrGmplsPeerTxResvErr | 1.3.6.1.4.1.6527.3.1.2.97.23.1.12 | Counter64 | read-only | The value of vRtrGmplsPeerTxResvErr indicates the total number of RSVP RESV ERROR messages that have been transmiited by this GMPLS Peer. |
| C64 vRtrGmplsPeerRxResvErr | 1.3.6.1.4.1.6527.3.1.2.97.23.1.13 | Counter64 | read-only | The value of vRtrGmplsPeerRxResvErr indicates the total number of RSVP RESV ERROR messages that have been received on this GMPLS Peer. |
| C64 vRtrGmplsPeerTxResvTear | 1.3.6.1.4.1.6527.3.1.2.97.23.1.14 | Counter64 | read-only | The value of vRtrGmplsPeerTxResvTear indicates the total number of RSVP RESV TEAR messages that have been transmitted from this GMPLS Peer. |
| C64 vRtrGmplsPeerRxResvTear | 1.3.6.1.4.1.6527.3.1.2.97.23.1.15 | Counter64 | read-only | The value of vRtrGmplsPeerRxResvTear indicates the total number of RSVP RESV TEAR messages that have been received by this GMPLS Peer. |
| C64 vRtrGmplsPeerTxNotify | 1.3.6.1.4.1.6527.3.1.2.97.23.1.16 | Counter64 | read-only | The value of vRtrGmplsPeerTxNotify indicates the total number of notification messages transmitted by this GMPLS Peer. |
| C64 vRtrGmplsPeerRxNotify | 1.3.6.1.4.1.6527.3.1.2.97.23.1.17 | Counter64 | read-only | The value of vRtrGmplsPeerRxNotify indicates the total number of notification messages received by this GMPLS Peer. |
| C64 vRtrGmplsPeerTxSRefreshes | 1.3.6.1.4.1.6527.3.1.2.97.23.1.18 | Counter64 | read-only | The value of vRtrGmplsPeerTxSRefreshes indicates the total number of summary refresh, SREFRESH, messages that have been transmitted on this RSVP interface. |
| C64 vRtrGmplsPeerRxSRefreshes | 1.3.6.1.4.1.6527.3.1.2.97.23.1.19 | Counter64 | read-only | The value of vRtrGmplsPeerRxSRefreshes indicates the total number of summary refresh, SREFRESH, messages that have been received on this RSVP interface. |
| C64 vRtrGmplsPeerTxAcks | 1.3.6.1.4.1.6527.3.1.2.97.23.1.20 | Counter64 | read-only | The value of vRtrGmplsPeerTxAcks indicates the total number of RSVP ACK messages that have been transmitted on this RSVP interface when refresh reduction is enabled. |
| C64 vRtrGmplsPeerRxAcks | 1.3.6.1.4.1.6527.3.1.2.97.23.1.21 | Counter64 | read-only | The value of vRtrGmplsPeerRxAcks indicates the total number of RSVP ACK messages that have been received on this RSVP interface when refresh reduction is enabled. |
| vRtrGmplsSessionTable | 1.3.6.1.4.1.6527.3.1.2.97.24 | not-accessible | The vRtrGmplsSessionTable contains objects for reporting sessions associated with the GMPLS protocol running in a virtual router. | |
| vRtrGmplsSessionEntry | 1.3.6.1.4.1.6527.3.1.2.97.24.1 | not-accessible | Each row entry represents a session of the GMPLS protocol within a virtual router. Entries in this table cannot be created and deleted via SNMP SET operations. An entry in this table is created be the agent when the GMPLS protocol establishes a session. The entry is destroyed when the GMPLS session is removed. | |
| IPt vRtrGmplsSessEndpointType | 1.3.6.1.4.1.6527.3.1.2.97.24.1.1 | InetAddressType | not-accessible | The value of vRtrGmplsSessEndpointType indicates the address type of vRtrGmplsSessEndpoint |
| IP vRtrGmplsSessEndpoint | 1.3.6.1.4.1.6527.3.1.2.97.24.1.2 | InetAddress | not-accessible | The value of vRtrGmplsSessEndpoint indicates the endpoint address of of this session. |
| IPt vRtrGmplsSessExtTunnelIdType | 1.3.6.1.4.1.6527.3.1.2.97.24.1.3 | InetAddressType | not-accessible | The value of vRtrGmplsSessExtTunnelIdType indicates the address type of vRtrGmplsSessExtTunnelId. |
| IP vRtrGmplsSessExtTunnelId | 1.3.6.1.4.1.6527.3.1.2.97.24.1.4 | InetAddress | not-accessible | The value of vRtrGmplsSessExtTunnelId indicates the extended tunnel id for this session. |
| IPt vRtrGmplsSessSenderType | 1.3.6.1.4.1.6527.3.1.2.97.24.1.5 | InetAddressType | not-accessible | The value of vRtrGmplsSessSenderType indicates the address type of vRtrGmplsSessSender. |
| IP vRtrGmplsSessSender | 1.3.6.1.4.1.6527.3.1.2.97.24.1.6 | InetAddress | not-accessible | The value of vRtrGmplsSessSender indicates the sender address for this session. |
| TMN vRtrGmplsSessionOperState | 1.3.6.1.4.1.6527.3.1.2.97.24.1.7 | TmnxGmplsSessionOperState | read-only | The value of vRtrGmplsSessionOperState indicates the current operational state of this GMPLS session. |
| T/F vRtrGmplsSessionIsProtectPath | 1.3.6.1.4.1.6527.3.1.2.97.24.1.8 | TruthValue | read-only | The value of vRtrGmplsSessionIsProtectPath when 'true' indicates that this session is for a protecting LSP. |
| INT vRtrGmplsSessionType | 1.3.6.1.4.1.6527.3.1.2.97.24.1.9 | INTEGER | read-only | The value of vRtrGmplsSessionType indicates this node's position in the path of this GMPLS session. |
| STR vRtrGmplsSessionName | 1.3.6.1.4.1.6527.3.1.2.97.24.1.10 | DisplayString | read-only | The value of vRtrGmplsSessionName indicates the session name for this GMPLS session. |
| U32 vRtrGmplsSessionSetupPriority | 1.3.6.1.4.1.6527.3.1.2.97.24.1.11 | Unsigned32 | read-only | The value of vRtrGmplsSessionSetupPriority indicates the setup priority used for this GMPLS session. A value of zero (0) is the highest priority and a value of seven (7) is the lowest priority. |
| U32 vRtrGmplsSessionHoldPriority | 1.3.6.1.4.1.6527.3.1.2.97.24.1.12 | Unsigned32 | read-only | The value of vRtrGmplsSessionHoldPriority indicates the hold priority to be used for this GMPLS session. A value of zero (0) is the highest priority and a value of seven (7) is the lowest priority. |
| U32 vRtrGmplsSessUpStreamPeer | 1.3.6.1.4.1.6527.3.1.2.97.24.1.13 | Unsigned32 | read-only | The value of vRtrGmplsSessUpStreamPeer indicates the upstream peer node-id for this GMPLS session. |
| U32 vRtrGmplsSessUpStreamTeLink | 1.3.6.1.4.1.6527.3.1.2.97.24.1.14 | Unsigned32 | read-only | The value of vRtrGmplsSessUpStreamTeLink indicates the upstream TE link ID for this GMPLS session. |
| U32 vRtrGmplsSessUpStreamDbLinkId | 1.3.6.1.4.1.6527.3.1.2.97.24.1.15 | Unsigned32 | read-only | The value of vRtrGmplsSessUpStreamDbLinkId indicates the upstream data-bearer link ID for this GMPLS session. |
| U32 vRtrGmplsSessUpStrmRmtDbLinkId | 1.3.6.1.4.1.6527.3.1.2.97.24.1.16 | Unsigned32 | read-only | The value of vRtrGmplsSessUpStrmRmtDbLinkId indicates the upstream remote data-bearer link ID for this GMPLS session. |
| U32 vRtrGmplsSessDnStreamPeer | 1.3.6.1.4.1.6527.3.1.2.97.24.1.17 | Unsigned32 | read-only | The value of vRtrGmplsSessDnStreamPeer indicates the downstream peer node-id for this GMPLS session. |
| U32 vRtrGmplsSessDnStreamTeLink | 1.3.6.1.4.1.6527.3.1.2.97.24.1.18 | Unsigned32 | read-only | The value of vRtrGmplsSessDnStreamTeLink indicates the downstream TE link ID for this GMPLS session. |
| U32 vRtrGmplsSessDnStreamDbLinkId | 1.3.6.1.4.1.6527.3.1.2.97.24.1.19 | Unsigned32 | read-only | The value of vRtrGmplsSessDnStreamDbLinkId indicates the downstream data-bearer link ID for this GMPLS session. |
| U32 vRtrGmplsSessDnStrmRmtDbLinkId | 1.3.6.1.4.1.6527.3.1.2.97.24.1.20 | Unsigned32 | read-only | The value of vRtrGmplsSessDnStrmRmtDbLinkId indicates the downstream remote data-bearer link ID for this GMPLS session. |
| NUM vRtrGmplsSessLastOperChange | 1.3.6.1.4.1.6527.3.1.2.97.24.1.21 | TimeInterval | read-only | The value of vRtrGmplsSessLastOperChange indicates the time interval which has elapsed since the GMPLS session's operational state last changed. |
| T/F vRtrGmplsSessDataPathIsActive | 1.3.6.1.4.1.6527.3.1.2.97.24.1.22 | TruthValue | read-only | The value of vRtrGmplsSessDataPathIsActive indicates whether the data path is active or not for this GMPLS session. |
| TMN vRtrGmplsSessionOperBandwidth | 1.3.6.1.4.1.6527.3.1.2.97.24.1.23 | TmnxGmplsSessionBWSignalType | read-only | The value of vRtrGmplsSessionOperBandwidth indicates the operational bandwidth for this GMPLS session. |
| U32 vRtrGmplsSessionHoldTimerRem | 1.3.6.1.4.1.6527.3.1.2.97.24.1.24 | Unsigned32 | read-only | The value of vRtrGmplsSessionHoldTimerRem indicates the time remaining, in seconds that the software waits after a session for this peer to become operationally up before activating data transmission on the session. |
| U32 vRtrGmplsSessionNumWP | 1.3.6.1.4.1.6527.3.1.2.97.24.1.25 | Unsigned32 | read-only | The value of vRtrGmplsSessionNumWP indicates the total number of working path associated with this protect path. The value of vRtrGmplsSessionNumWP is valid only when vRtrGmplsSessionIsProtectPath is set to 'true', otherwise the value of vRtrGmplsSessionNumWP is 0. |
| vRtrGmplsSessionStatsTable | 1.3.6.1.4.1.6527.3.1.2.97.25 | not-accessible | The vRtrGmplsSessionStatsTable contains objects for reporting statistics for the sessions associated with the GMPLS protocol running in a virtual router. | |
| vRtrGmplsSessionStatsEntry | 1.3.6.1.4.1.6527.3.1.2.97.25.1 | not-accessible | Each row entry represents statistics for a session of the GMPLS protocol within a virtual router. Entries in this table cannot be created and deleted via SNMP SET operations. An entry in this table is created be the agent when the GMPLS protocol establishes a session. The entry is destroyed when the GMPLS session is removed. | |
| C64 vRtrGmplsSessStatRxPaths | 1.3.6.1.4.1.6527.3.1.2.97.25.1.1 | Counter64 | read-only | The value of vRtrGmplsSessStatRxPaths indicates the total number of PATH messages received for this GMPLS sessio. |
| C64 vRtrGmplsSessStatTxPaths | 1.3.6.1.4.1.6527.3.1.2.97.25.1.2 | Counter64 | read-only | The value of vRtrGmplsSessStatTxPaths indicates the total number of PATH messages transmitted for this GMPLS sessio. |
| C64 vRtrGmplsSessStatRxResv | 1.3.6.1.4.1.6527.3.1.2.97.25.1.3 | Counter64 | read-only | The value of vRtrGmplsSessStatRxResv indicates the total number of RESV messages received for this GMPLS session. |
| C64 vRtrGmplsSessStatTxResv | 1.3.6.1.4.1.6527.3.1.2.97.25.1.4 | Counter64 | read-only | The value of vRtrGmplsSessStatTxResv indicates the total number of RESV messages transmitted for this GMPLS session. |
| C64 vRtrGmplsSessStatSummRxPath | 1.3.6.1.4.1.6527.3.1.2.97.25.1.5 | Counter64 | read-only | The value of vRtrGmplsSessStatSummRxPath indicates the total number of summary PATH messages received. |
| C64 vRtrGmplsSessStatSummTxPath | 1.3.6.1.4.1.6527.3.1.2.97.25.1.6 | Counter64 | read-only | The value of vRtrGmplsSessStatSummTxPath indicates the total number of summary PATH messages transmitted. |
| C64 vRtrGmplsSessStatSummRxResv | 1.3.6.1.4.1.6527.3.1.2.97.25.1.7 | Counter64 | read-only | The value of vRtrGmplsSessStatSummRxResv indicates the total number of summary RESV messages received. |
| C64 vRtrGmplsSessStatSummTxResv | 1.3.6.1.4.1.6527.3.1.2.97.25.1.8 | Counter64 | read-only | The value of vRtrGmplsSessStatSummTxResv indicates the total number of summary RESV messages transmitted. |
| vRtrGmplsARHopTable | 1.3.6.1.4.1.6527.3.1.2.97.26 | not-accessible | The vRtrGmplsARHopTable contains objects for actual-hop associated with the GMPLS protocol running in a virtual router. | |
| vRtrGmplsARHopEntry | 1.3.6.1.4.1.6527.3.1.2.97.26.1 | not-accessible | Each row entry represents actual-hop information for the GMPLS protocol within a virtual router. Entries in this table cannot be created and deleted via SNMP SET operations. An entry in this table is created be the agent when the GMPLS protocol establishes a session. The entry is destroyed when the GMPLS session is removed. | |
| U32 vRtrGmplsARHopListIndex | 1.3.6.1.4.1.6527.3.1.2.97.26.1.1 | Unsigned32 | not-accessible | The value of vRtrGmplsARHopListIndex indicates the list index identifying the actual hop list for this GMPLS. |
| U32 vRtrGmplsARHopIndex | 1.3.6.1.4.1.6527.3.1.2.97.26.1.2 | Unsigned32 | not-accessible | The value of vRtrGmplsARHopIndex indicates the secondary index identifying the particular hop within the list. |
| ADR vRtrGmplsARHopAddrType | 1.3.6.1.4.1.6527.3.1.2.97.26.1.3 | TmnxGmplsARHopAddressType | read-only | The value of vRtrGmplsARHopAddrType indicates the address type of the particular hop. |
| TMN vRtrGmplsARHopRouterId | 1.3.6.1.4.1.6527.3.1.2.97.26.1.4 | TmnxGmplsRouterId | read-only | The value of vRtrGmplsARHopRouterId indicates the router ID for the node corresponding to this hop. |
| U32 vRtrGmplsARHopUnnumIfId | 1.3.6.1.4.1.6527.3.1.2.97.26.1.5 | Unsigned32 | read-only | The value of vRtrGmplsARHopUnnumIfId indicates the unnumbered interface identifier of this hop. This object should be used in conjunction with vRtrGmplsARHopRouterId which would contain the Router ID for the unnumbered interface. |
| U32 vRtrGmplsARHopSrlgListIndex | 1.3.6.1.4.1.6527.3.1.2.97.26.1.6 | Unsigned32 | read-only | The value of vRtrGmplsARHopSrlgListIndex indicates the SRLG list index corresponding to this hop. |
| U32 vRtrGmplsARHopDownStreamLabel | 1.3.6.1.4.1.6527.3.1.2.97.26.1.7 | Unsigned32 | read-only | The value of vRtrGmplsARHopDownStreamLabel indicates the downstream label for this hop. |
| U32 vRtrGmplsARHopUpStreamLabel | 1.3.6.1.4.1.6527.3.1.2.97.26.1.8 | Unsigned32 | read-only | The value of vRtrGmplsARHopUpStreamLabel indicates the upstream label for this hop. |
| vRtrGmplsSrlgListTable | 1.3.6.1.4.1.6527.3.1.2.97.27 | not-accessible | The vRtrGmplsSrlgListTable contains objects for an srlg-list associated with the GMPLS protocol running in a virtual router. | |
| vRtrGmplsSrlgListEntry | 1.3.6.1.4.1.6527.3.1.2.97.27.1 | not-accessible | Each row entry represents SRLG List information for the GMPLS protocol within a virtual router. Entries in this table cannot be created and deleted via SNMP SET operations. An entry in this table is created be the agent when the GMPLS protocol establishes a session. The entry is destroyed when the GMPLS session is removed. | |
| U32 vRtrGmplsSrlgListIndex | 1.3.6.1.4.1.6527.3.1.2.97.27.1.1 | Unsigned32 | not-accessible | The value of vRtrGmplsSrlgListIndex indicates the SRLG list index for this GMPLS. |
| U32 vRtrGmplsSrlgValue | 1.3.6.1.4.1.6527.3.1.2.97.27.1.2 | Unsigned32 | not-accessible | The value of vRtrGmplsSrlgValue indicates the SRLG value for this row. |
| INT vRtrGmplsSrlgListType | 1.3.6.1.4.1.6527.3.1.2.97.27.1.3 | INTEGER | read-only | The value of vRtrGmplsSrlgListType indicates the type of SRLG list. If the value for vRtrGmplsSrlgListType is record(1), the SRLG list represents the SRLGs recorded for a hop in the Record Route Object(RRO). |
| tmnxGmplsCmdObjs | 1.3.6.1.4.1.6527.3.1.2.97.28 | |||
| vRtrGmplsCommandTable | 1.3.6.1.4.1.6527.3.1.2.97.28.1 | not-accessible | The vRtrGmplsCommandTable maintains the one-shot action commands that effect the state of the GMPLS operation. | |
| vRtrGmplsCommandEntry | 1.3.6.1.4.1.6527.3.1.2.97.28.1.1 | not-accessible | The vRtrGmplsCommandEntry contains the command available to execute on an existing GMPLS LSP Path. | |
| INT vRtrGmplsCommandSwitch | 1.3.6.1.4.1.6527.3.1.2.97.28.1.1.1 | INTEGER | read-create | The value of vRtrGmplsCommandSwitch specifies the switch command to initiate on GMPLS LSP Path. When read, this object returns the last command written or 'noCmd (0)' if no command has been written to this GMPLS LSP Path since initialization. The return of the last command written does not imply that this command is currently in effect. This request may be preempted by a higher priority local or remote request. The value 'noCmd (0)' may not be used in a write command. The value 'clearLockout (1)' clears the lockout on the protection path. The value of 'forceSwitch (2)' switches the active path to the protection path. The value of 'manualSwitch (3)' switches the active path to the protection path. The value of 'revertSwitch (4)' switches the active path to the working path. The value of 'lockout (5)' prevents the working path from switching to the protection path. |
| tmnxGmplsNotifyPrefix | 1.3.6.1.4.1.6527.3.1.3.97 | |||
| tmnxGmplsNotifications | 1.3.6.1.4.1.6527.3.1.3.97.0 | |||
| NTF vRtrGmplsLspPathStateChange | 1.3.6.1.4.1.6527.3.1.3.97.0.1 | A vRtrGmplsLspPathStateChange notification is generated when the operational state of the GMPLS LSP Path changes. |
RFC description
Nokia SROS GMPLS (Generalized Multi-Protocol Label Switching) extensions for optical network control.
Start monitoring Nokia (Alcatel-Lucent) 7750 SR router, SROS GMPLS-enabled (GMPLS instance admin/oper status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.