EFM-COMMON-MIB

All MIBs › EFM-COMMON-MIB

Organization: IETF Ethernet Interfaces and Hub MIB Working Group

Last Updated: 2005-03-22

Description: EFM-COMMON-MIB module

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is EFM-COMMON-MIB?

EFM-COMMON-MIB is a vendor-neutral, standards-based IETF MIB module defining common object types and conventions for Ethernet in the First Mile (EFM) OAM, based on IEEE 802.3ah Clause 30, applicable to Ethernet-like interfaces on any physical layer. As a common module, it establishes shared textual conventions and definitions used by the broader Ethernet OAM MIB suite rather than exposing device-specific monitoring tables of its own. It has no direct runtime monitoring objects itself (no sample objects were captured), but it underpins consistent representation of OAM-related fault/status data such as link-fault detection, remote loopback, and event notification across compliant implementations. As an IETF standards MIB, it is explicitly foundational to and depended upon by the full suite of 802.3ah Ethernet OAM MIB modules. It is typically deployed alongside other Ethernet OAM MIBs on carrier Ethernet access equipment supporting first-mile link monitoring between a subscriber and provider network. Engineers implementing or auditing this functionality typically reference the EFM-COMMON-MIB RFC/standard documentation for the authoritative specification.

IPNetwork Monitor allows you to monitor SNMP objects defined in EFM-COMMON-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

vendor-neutral, standards-based MIB, not tied to a specific manufacturer
Ethernet-like interfaces on carrier/access network equipment (802.3ah EFM OAM)

Monitoring Examples

This module defines shared conventions and types for the IEEE 802.3ah Ethernet OAM feature set rather than pollable runtime objects (no sample objects were captured), so there is no standalone monitoring scenario to describe; the actual pollable link-fault, loopback, and event objects live in the companion Ethernet OAM MIB modules that import these common definitions.

Imported Objects

From HCNUM-TC

CounterBasedGauge64

From IF-MIB

ifIndex

OBJECT-TYPE

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32
mib-2

From SNMPv2-TC

MacAddress
TEXTUAL-CONVENTION
TimeStamp

OIDs

OID symbolic	OID numeric	Type	Access	Description
efmOamMIB	1.3.6.1.2.1.9908			The MIB module for managing the new Ethernet OAM features introduced by the Ethernet in the First Mile task force (IEEE 802.3ah). The functionality presented here is based on IEEE 802.3ah [802.3ah], released in October, 2004. In particular, this MIB focused on the changes to Clause 30 of the draft that are not specific to any physical layer. These changes are primarily reflected in the new OAM features developed under this project, that can be applied to any Ethernet like interface. The OAM features are described in Clause 57 of [802.3ah]. The following reference is used throughout this MIB module: [802.3ah] refers to: IEEE Std 802.3ah-2004: 'Draft amendment to - Information technology - Telecommunications and information exchange between systems - Local and metropolitan are networks - Specific requirements - Part 3: Carrier sense multiple access with collision detection (CSMA/CD) access method and physical layer specifications - Media Access Control Parameters, Physical Layers and Management Parameters for subscriber access networks', October 2004. [802-2001] refers to: 'IEEE Standard for LAN/MAN (Local Area Network/Metropolitan Area Network): Overview and Architecture', IEEE 802, June 2001. Copyright (c) The Internet Society (2005). This version of this MIB module is part of RFC XXXX; See the RFC itself for full legal notices.
dot3OamMIB	1.3.6.1.2.1.9908.1
dot3OamTable	1.3.6.1.2.1.9908.1.1		not-accessible	Primary controls and status for the OAM capabilities of an Ethernet like interface. There will be one row in this table for each Ethernet like interface in the system that supports the Ethernet OAM functions defined in [802.3ah].
dot3OamEntry	1.3.6.1.2.1.9908.1.1.1		not-accessible	An entry in the table, containing information on the Ethernet OAM function for a single Ethernet like interface.
INT dot3OamAdminState	1.3.6.1.2.1.9908.1.1.1.1	INTEGER	read-write	This object is used to provision the default administrative OAM mode for this interface. This object represents the desired state of OAM for this interface. The dot3OamAdminState always starts in the disabled(1) state until an explicity management action or configuration information retained by the system causes a transition to the enabled(2) state. Note that the value of this object is ignored when the interface is not operating in full-duplex mode. OAM is not supported on half-duplex links.
INT dot3OamOperStatus	1.3.6.1.2.1.9908.1.1.1.2	INTEGER	read-only	At initialization and failure conditions, two OAM entities on the same full-duplex Ethernet link begin a discovery phase to determine what OAM capabilities may be used on that link. The progress of this initialization is controlled by the OAM sublayer. This value is always disabled(1) if OAM is disabled on this interface via the dot3OamAdminState. If the link has detected a fault and is transmitting OAMPDUs with a link fault indication, the value is linkFault(2). The passiveWait(3) state is returned only by OAM entities in passive mode (dot3OamMode) and reflects the state in which the OAM entity is waiting to see if the peer device is OAM capable. The activeSendLocal(4) is used by active mode devices (dot3OamMode) and reflects the OAM entity actively trying to discover whether the peer has OAM capability but has not yet made that determination. The state sendLocalAndRemote(5) reflects that the local OAM entity has discovered the peer but has not yet accepted or rejected the configuration of the peer. The local device can, for whatever reason, decide that the peer device is unacceptable and decline OAM peering. If the local OAM entity rejects the peer OAM entity, the state becomes oamPeeringLocallyRejected(7). If the OAM peering is allowed by the local device, the state moves to sendLocalAndRemoteOk(6). Note that both the sendLocalAndRemote(5) and oamPeeringLocallyRejected(7) states fall within the state SEND_LOCAL_REMOTE of the Discovery state diagram [802.3ah, Figure 57-5], with the difference being whether the local OAM client has actively rejected the peering or has just not indicated any decision yet. Whether a peering decision has been made is indicated via the local flags field in the OAMPDU (reflected in the aOAMLocalFlagsField of 30.3.6.1.10). If the remote OAM entity rejects the peering, the state becomes oamPeeringRemotelyRejected(8). Note that both the sendLocalAndRemoteOk(6) and oamPeeringRemotelyRejected(8) states fall within the state SEND_LOCAL_REMOTE_OK of the Discovery state diagram [802.3ah, Figure 57-5], with the difference being whether the remote OAM client has rejected the peering or has just not yet decided. This is indicated via the remote flags field in the OAM PDU (reflected in the aOAMRemoteFlagsField of 30.3.6.1.11). When the local OAM entity learns that both it and the remote OAM entity have accepted the peering, the state moves to operational(9) corresponding to the SEND_ANY state of the Discovery state diagram [802.3ah, Figure 57-5].
INT dot3OamMode	1.3.6.1.2.1.9908.1.1.1.3	INTEGER	read-write	This object configures the mode of OAM operation for this Ethernet like interface. OAM on Ethernet interfaces may be in 'active' mode or 'passive' mode. These two modes differ in that active mode provides additional capabilities to initiate monitoring activities with the remote OAM peer entity, while passive mode generally waits for the peer to initiate OAM actions with it. As an example, an active OAM entity can put the remote OAM entity in a loopback state, where a passive OAM entity cannot. The default value of dot3OamMode is dependent on the type of system on which this Ethernet like interface resides. The default value should be 'active(1)' unless it is known that this system should take on a subservient role to the other device connected over this interface. Changing this value results in incrementing the configuration revision field of locally generated OAMPDUs (30.3.6.1.12) and potentially re-doing the OAM discovery process if the dot3OamOperStatus was already operational(9).
I32 dot3OamMaxOamPduSize	1.3.6.1.2.1.9908.1.1.1.4	Integer32	read-only	The largest OAMPDU that the OAM entity supports. OAM entities exchange maximum OAMPDU sizes and negotiate to use the smaller of the two maximum OAMPDU sizes between the peers. This value is determined by the local implementation.
U32 dot3OamConfigRevision	1.3.6.1.2.1.9908.1.1.1.5	Unsigned32	read-only	The configuration revision of the OAM entity as reflected in the latest OAMPDU sent by the OAM entity. The config revision is used by OAM entities to indicate configuration changes have occured which might require the peer OAM entity to re-evaluate whether the peering is allowed. See local_satisfied in [802.3ah, 57.3.1.2].
BIT dot3OamFunctionsSupported	1.3.6.1.2.1.9908.1.1.1.6	Bits	read-only	The OAM functions supported on this Ethernet like interface. OAM consists of separate functional sets beyond the basic discovery process which is always required. These functional groups can be supported independently by any implementation. These values are communicated to the peer via the local configuration field of Information OAMPDUs.
dot3OamPeerTable	1.3.6.1.2.1.9908.1.2		not-accessible	Information about the OAM peer for a particular Ethernet like interface. OAM entities communicate with a single OAM peer entity on full-duplex Ethernet links on which OAM is enabled and operating properly. In certain states, the OAM peer information is not available. Whether peer information is available is communicated via the dot3OamPeerStatus object. When this object is inactive, all other information in the row is to be considered invalid.
dot3OamPeerEntry	1.3.6.1.2.1.9908.1.2.1		not-accessible	An entry in the table, containing information on the peer OAM entity for a single Ethernet like interface. Note that there is at most one OAM peer for each Ethernet like interface. There is exactly one row in this table for each Ethernet like interface supporting OAM.
INT dot3OamPeerStatus	1.3.6.1.2.1.9908.1.2.1.1	INTEGER	read-only	This object indicates whether the information in this row should be considered valid. When active(1), the information is valid and represents the current peer of the OAM entity. When inactive(2), the information in this row is invalid. A value of inactive(2) is returned if the dot3OamOperStatus is disabled, passiveWait, or activeSendLocal. For all other values of dot3OamOperStatus, a value of active(1) is returned.
MAC dot3OamPeerMacAddress	1.3.6.1.2.1.9908.1.2.1.2	MacAddress	read-only	The MAC address of the peer OAM entity. The MAC address is derived from the most recently received OAMPDU. This value is initialized to all zeros (0x000000000000). This value is invalid if the dot3OamPeerStatus is inactive. An OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) and a Slow Protocols subtype equal to that of the subtype reserved for OAM.
DOT dot3OamPeerVendorOui	1.3.6.1.2.1.9908.1.2.1.3	Dot3Oui	read-only	The OUI of the OAM peer as reflected in the latest Information OAMPDU received with a Local Information TLV. The OUI can be used to identify the vendor of the remote OAM entity. This value is initialized to all zeros (0x000000). This value is considered invalid if the dot3OamPeerStatus is inactive. An Information OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, (4) a OAM code that equals the code reserved for Information OAMPDUs.
U32 dot3OamPeerVendorInfo	1.3.6.1.2.1.9908.1.2.1.4	Unsigned32	read-only	The Vendor Info of the OAM peer as reflected in the latest Information OAMPDU received with a Local Information TLV. The vendor information field is within the Local Information TLV, and can be used to determine additional information about the peer entity. The format of the vendor information is unspecified within the 32-bit field. This value is intialized to all zeros (0x00000000). This value is invalid if the dot3OamPeerStatus is inactive. An Information OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, and (4) a OAM code that equals the code reserved for Information OAMPDUs.
INT dot3OamPeerMode	1.3.6.1.2.1.9908.1.2.1.5	INTEGER	read-only	The mode of the OAM peer as reflected in the latest Information OAMPDU received with a Local Information TLV. The mode of the peer can be determined from the Configuration field in the Local Information TLV of the last Information OAMPDU received from the peer. This value is initialized to unknown(3), and is not valid if the dot3OamPeerStatus is inactive. An Information OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, and (4) a OAM code that equals the code reserved for Information OAMPDUs.
I32 dot3OamPeerMaxOamPduSize	1.3.6.1.2.1.9908.1.2.1.6	Integer32	read-only	The maximum size of OAMPDU supported by the peer as reflected in the latest Information OAMPDU received with a Local Information TLV. Ethernet OAM on this interface must not use OAMPDUs that exceed this size. The maximum OAMPDU size can be determined from the PDU Configuration field of the Local Information TLV of the last Information OAMPDU received from the peer. This value is initialized to 64, and is invalid if the dot3OamPeerStatus is inactive. An Information OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, and (4) a OAM code that equals the code reserved for Information OAMPDUs.
U32 dot3OamPeerConfigRevision	1.3.6.1.2.1.9908.1.2.1.7	Unsigned32	read-only	The configuration revision of the OAM peer as reflected in the latest OAMPDU. This attribute is changed by the peer whenever it has a local configuration change for Ethernet OAM this interface. This value is initialized to all zeros (0x00000000), and is invalid if the dot3OamPeerStatus is inactive. The configuration revision can be determined from the Revision field of the Local Information TLV of the most recently received Information OAMPDU with a Local Information TLV. An Information OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, and (4) a OAM code that equals the code reserved for Information OAMPDUs.
BIT dot3OamPeerFunctionsSupported	1.3.6.1.2.1.9908.1.2.1.8	Bits	read-only	The OAM functions supported on this Ethernet like interface. OAM consists of separate functionality sets above the basic discovery process. This value indicates the capabilities of the peer OAM entity with respect to these functions. This value is initialized so all bits are clear, and is invalid if the dot3OamPeerStatus is inactive. The capbilities of the OAM peer can be determined from the configuration field of the Local Information TLV of the most recently received Information OAMPDU with a Local Information TLV. An Information OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, and (4) a OAM code that equals the code reserved for Information OAMPDUs.
dot3OamLoopbackTable	1.3.6.1.2.1.9908.1.3		not-accessible	This table contains methods to control the loopback state of the local link as well as indicating the status of the loopback function. Loopback can be used to place the remote OAM entity in a state where every received frame (except OAMPDUs) are echoed back over the same interface on which they were received. In this state, at the remote entity, 'normal' traffic is disabled as only the looped back frames are transmitted on the interface. Loopback is thus an intrusive operation that prohibits normal data flow and should be used accordingly.
dot3OamLoopbackEntry	1.3.6.1.2.1.9908.1.3.1		not-accessible	An entry in the table, containing information on the loopback status for a single Ethernet like interface. There is an entry in this table for every Ethernet like interface on which supports OAM and loopback function within OAM (as indicated in dot3OamFunctionsSupported).
INT dot3OamLoopbackCommand	1.3.6.1.2.1.9908.1.3.1.1	INTEGER	read-write	This attribute initiates or terminates remote loopback with an OAM peer. Writing startRemoteLoopback(2) to this attribute cause the local OAM client to send a loopback OAMPDU to the OAM peer with the loopback enable flags set. Writing stopRemoteLoopback(3) to this attribute will cause the local OAM client to send a loopback OAMPDU to the OAM peer with the loopback enable flags cleared. Writing noLoopback to this attribute has no effect. Writes to this attribute are ignored unless the OAM status of this interface is 'operational' (dot3OamOperStatus). The attribute always returns noLoopback on a read. To determine the loopback status, use the attribute dot3OamLoopbackStatus.
INT dot3OamLoopbackStatus	1.3.6.1.2.1.9908.1.3.1.2	INTEGER	read-only	The loopback status of the OAM entity. This status is determined by a combination of the local parser and multiplexer states, the remote parser and multiplexer states, as well as by the actions of the local OAM client. When operating in normal mode with no loopback in progress, the status reads noLoopback(1). If the OAM client has sent an Loopback OAMPDU and is waiting for a response, where the local parser and multiplexer states are DISCARD (see [802.3ah, 57.2.11.1]), the status is 'initiatingLoopback'. In this case, the local OAM entity has yet to receive any acknowledgement that the remote OAM entity has received its loopback command request. If the local OAM client knows that the remote OAM entity is in loopback mode (via the remote state information as described in [802.3ah, 57.2.11.1, 30.3.6.1.15]), the status is remoteLoopback(3). If the local OAM client is in the process of terminating the remote loopback [802.3ah, 57.2.11.3, 30.3.6.1.14], with its local multiplexer and parser states in DISCARD, the status is terminatingLoopback(4). If the remote OAM client has put the local OAM entity in loopback mode as indicated by its local parser state, the status is localLoopback(5). The unknown(6) status indicates the parser and multiplexer combination is unexpected. This status may be returned if the OAM loopback is in a transition state but should not persist. The values of this attribute correspond to the following values of the local and remote parser and multiplexer states. value LclPrsr LclMux RmtPrsr RmtMux noLoopback FWD FWD FWD FWD initLoopback DISCARD DISCARD FWD FWD rmtLoopback DISCARD FWD LPBK DISCARD tmtngLoopback DISCARD DISCARD LPBK DISCARD lclLoopback LPBK DISCARD DISCARD FWD unknown * any other combination *
INT dot3OamLoopbackIgnoreRx	1.3.6.1.2.1.9908.1.3.1.3	INTEGER	read-write	Since OAM loopback is a distruptive operation (user traffic does not pass), this attribute provides a mechanism to provide controls over whether received OAM loopback commands are processed or ignored. When the value is ignore(1), received loopback commands are ignored. When the value is process(2), OAM loopback commands are processed. The default value is to ignore loopback commands (ignore(1)). The attribute has no meaning if the local OAM entity does not support the loopback function (as defined in dot3OamFunctionsSupported).
dot3OamStatsTable	1.3.6.1.2.1.9908.1.4		not-accessible	Statistics for the OAM function on a particular Ethernet like interface.
dot3OamStatsEntry	1.3.6.1.2.1.9908.1.4.1		not-accessible	An entry in the table, containing statistics information on the Ethernet OAM function for a single Ethernet like interface.
C32 dot3OamInformationTx	1.3.6.1.2.1.9908.1.4.1.1	Counter32	read-only	A count of the number of Information OAMPDUs transmitted on this interface. An Information OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, and (4) an OAMPDU code equals the OAM Information code. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
C32 dot3OamInformationRx	1.3.6.1.2.1.9908.1.4.1.2	Counter32	read-only	A count of the number of Information OAMPDUs received on this interface. An Information OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, and (4) an OAMPDU code equals the OAM Information code. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
C32 dot3OamUniqueEventNotificationTx	1.3.6.1.2.1.9908.1.4.1.3	Counter32	read-only	A count of the number of unique Event OAMPDUs transmitted on this interface. Event notifications may be sent in duplicate to increase the probability of successfully being received, given the possiblity that a frame may be lost in transit. An Event Notification OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, and (4) an OAMPDU code equals the OAM Event code. A unique Event Notification OAMPDU is indicated as an Event Notification OAMPDU with a Sequence Number field that is distinct from the previously transmitted Event Notification OAMPDU Sequence Number. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
C32 dot3OamUniqueEventNotificationRx	1.3.6.1.2.1.9908.1.4.1.4	Counter32	read-only	A count of the number of unique Event OAMPDUs received on this interface. Event notification OAMPDUs may be sent in duplicate to increase the probability of successfully being received, given the possiblity that a frame may be lost in transit. An Event Notification OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, and (4) an OAMPDU code equals the OAM Event code. A unique Event Notification OAMPDU is indicated as an Event Notification OAMPDU with a Sequence Number field that is distinct from the previously received Event Notification OAMPDU Sequence Number. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
C32 dot3OamDuplicateEventNotificationTx	1.3.6.1.2.1.9908.1.4.1.5	Counter32	read-only	A count of the number of duplicate Event OAMPDUs transmitted on this interface. Event notification OAMPDUs may be sent in duplicate to increase the probability of successfully being received, given the possiblity that a frame may be lost in transit. An Event Notification OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, and (4) an OAMPDU code equals the OAM Event code. A duplicate Event Notification OAMPDU is indicated as an Event Notification OAMPDU with a Sequence Number field that is identical to the previously transmitted Event Notification OAMPDU Sequence Number. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
C32 dot3OamDuplicateEventNotificationRx	1.3.6.1.2.1.9908.1.4.1.6	Counter32	read-only	A count of the number of duplicate Event OAMPDUs received on this interface. Event notification OAMPDUs may be sent in duplicate to increase the probability of successfully being received, given the possiblity that a frame may be lost in transit. An Event Notification OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, and (4) an OAMPDU code equals the OAM Event code. A duplicate Event Notification OAMPDU is indicated as an Event Notification OAMPDU with a Sequence Number field that is identical to the previously received Event Notification OAMPDU Sequence Number. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
C32 dot3OamLoopbackControlTx	1.3.6.1.2.1.9908.1.4.1.7	Counter32	read-only	A count of the number of Loopback Control OAMPDUs transmitted on this interface. An Loopback Conrol OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, and (4) an OAMPDU code equals the OAM Loopback Control code. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
C32 dot3OamLoopbackControlRx	1.3.6.1.2.1.9908.1.4.1.8	Counter32	read-only	A count of the number of Loopback Control OAMPDUs transmitted on this interface. An Loopback Control OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, and (4) an OAMPDU code equals the OAM Loopback Control code. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
C32 dot3OamVariableRequestTx	1.3.6.1.2.1.9908.1.4.1.9	Counter32	read-only	A count of the number of Variable Request OAMPDUs transmitted on this interface. An Variable Request OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, and (4) an OAMPDU code equals the OAM Variable Request code. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
C32 dot3OamVariableRequestRx	1.3.6.1.2.1.9908.1.4.1.10	Counter32	read-only	A count of the number of Variable Request OAMPDUs received on this interface. An Variable Request OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, and (4) an OAMPDU code equals the OAM Variable Request code. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
C32 dot3OamVariableResponseTx	1.3.6.1.2.1.9908.1.4.1.11	Counter32	read-only	A count of the number of Variable Response OAMPDUs transmitted on this interface. An Variable Response OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, and (4) an OAMPDU code equals the OAM Variable Response code. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
C32 dot3OamVariableResponseRx	1.3.6.1.2.1.9908.1.4.1.12	Counter32	read-only	A count of the number of Variable Response OAMPDUs received on this interface. An Variable Response OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, and (4) an OAMPDU code equals the OAM Variable Response code. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
C32 dot3OamOrgSpecificTx	1.3.6.1.2.1.9908.1.4.1.13	Counter32	read-only	A count of the number of Organization Specific OAMPDUs transmitted on this interface. An Organization Specific OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, and (4) an OAMPDU code equals the OAM Organization Specific code. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
C32 dot3OamOrgSpecificRx	1.3.6.1.2.1.9908.1.4.1.14	Counter32	read-only	A count of the number of Organization Specific OAMPDUs received on this interface. An Organization Specific OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, and (4) an OAMPDU code equals the OAM Organization Specific code. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
C32 dot3OamUnsupportedCodesTx	1.3.6.1.2.1.9908.1.4.1.15	Counter32	read-only	A count of the number of OAMPDUs transmitted on this interface with an unsupported op-code. An unsupported opcode OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, and (4) an OAMPDU code equals the opcode for a function that is not supported by the device. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
C32 dot3OamUnsupportedCodesRx	1.3.6.1.2.1.9908.1.4.1.16	Counter32	read-only	A count of the number of OAMPDUs received on this interface with an unsupported op-code. An unsupported opcode OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, and (4) an OAMPDU code equals the opcode for a function that is not supported by the device. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
C32 dot3OamFramesLostDueToOam	1.3.6.1.2.1.9908.1.4.1.17	Counter32	read-only	A count of the number of frames that were dropped by the OAM multiplexer. Since the OAM mulitplexer has multiple inputs and a single output, there may be cases where frames are dropped due to transmit resource contention. This counter is incremented whenever a frame is dropped by the OAM layer. When this counter is incremented, no other counters in this MIB are incremented. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
dot3OamEventConfigTable	1.3.6.1.2.1.9908.1.5		not-accessible	Ethernet OAM includes the ability to generate and receive event notifications to indicate various link problems. This table contains the mechanisms to configure the thresholds to generate the standard Ethernet OAM events. These events are: - Errored Symbol Period Event. Generated when the number of symbol errors exceeds a threshold within a given window defined by a number of symbols (e.g. 1,000 symbols out of 1,000,000 had errors). - Errored Frame Period Event. Generated when the number of frame errors exceeds a threshold within a given window defined by a number of frames (e.g. 10 frames out of 1000 had errors). - Errored Frame Event. Generated when the number of frame errors exceeds a threshold within a given window defined by a period of time (e.g. 10 frames in 1 second had errors). - Errored Frame Seconds Summary Event. Generated when the number of errored frame seconds exceeds a threshold within a given time period (e.g. 10 errored frame seconds within the last 100 seconds). An errored frame second is defined as a 1 second interval which had >0 frame errors.
dot3OamEventConfigEntry	1.3.6.1.2.1.9908.1.5.1		not-accessible	Event configuration information is available for every Ethernet like interface that supports OAM and the event function of OAM as indicated in the dot3OamFunctionsSupported attribute. Event configuration controls when the local management entity sends Event Notification OAMPDUs to its OAM peer.
U32 dot3OamErrSymPeriodWindowHi	1.3.6.1.2.1.9908.1.5.1.1	Unsigned32	read-write	The two objects dot3OamErrSymPeriodWindowHi and dot3OamErrSymPeriodLo together form an unsigned 64-bit integer representing the number of symbols over which this threshold event is defined. This is defined as dot3OamErrSymPeriodWindow = ((2^32)*dot3OamErrSymPeriodWindowHi) + dot3OamErrSymPeriodWindowLo If dot3OamErrSymPeriodThreshold symbol errors occur within a window of dot3OamErrSymPeriodWindow symbols, an Event Notification OAMPDU should be generated with an Errored Symbol Period Event TLV indicating the threshold has been crossed in this window. The default value for dot3OamErrSymPeriodWindow is the number of symbols in one second for the underlying physical layer.
U32 dot3OamErrSymPeriodWindowLo	1.3.6.1.2.1.9908.1.5.1.2	Unsigned32	read-write	The two objects dot3OamErrSymPeriodWindowHi and dot3OamErrSymPeriodWindowLo together form an unsigned 64-bit integer representing the number of symbols over which this threshold event is defined. This is defined as dot3OamErrSymPeriodWindow = ((2^32)*dot3OamErrSymPeriodWindowHi) + dot3OamErrSymPeriodWindowLo If dot3OamErrSymPeriodThreshold symbol errors occur within a window of dot3OamErrSymPeriodWindow symbols, an Event Notification OAMPDU should be generated with an Errored Symbol Period Event TLV indicating the threshold has been crossed in this window. The default value for dot3OamErrSymPeriodWindow is the number of symbols in one second for the underlying physical layer.
U32 dot3OamErrSymPeriodThresholdHi	1.3.6.1.2.1.9908.1.5.1.3	Unsigned32	read-write	The two objects dot3OamErrSymPeriodThresholdHi and dot3OamErrSymPeriodThresholdLo together form an unsigned 64-bit integer representing the number of symbol errors that must occur within a given window to cause this event. This is defined as dot3OamErrSymPeriodThreshold = ((2^32) * dot3OamErrSymPeriodThresholdHi) + dot3OamErrSymPeriodThresholdLo If dot3OamErrSymPeriodThreshold symbol errors occur within a window of dot3OamErrSymPeriodWindow symbols, an Event Notification OAMPDU should be generated with an Errored Symbol Period Event TLV indicating the threshold has been crossed in this window. The default value for dot3OamErrSymPeriodThreshold is one symbol errors.
U32 dot3OamErrSymPeriodThresholdLo	1.3.6.1.2.1.9908.1.5.1.4	Unsigned32	read-write	The two objects dot3OamErrSymPeriodThresholdHi and dot3OamErrSymPeriodThresholdLo together form an unsigned 64-bit integer representing the number of symbol errors that must occur within a given window to cause this event. This is defined as dot3OamErrSymPeriodThreshold = ((2^32) * dot3OamErrSymPeriodThresholdHi) + dot3OamErrSymPeriodThresholdLo If dot3OamErrSymPeriodThreshold symbol errors occur within a window of dot3OamErrSymPeriodWindow symbols, an Event Notification OAMPDU should be generated with an Errored Symbol Period Event TLV indicating the threshold has been crossed in this window. The default value for dot3OamErrSymPeriodThreshold is one symbol error.
INT dot3OamErrSymPeriodEvNotifEnable	1.3.6.1.2.1.9908.1.5.1.5	INTEGER	read-write	Indicates whether the occurence of Errored Symbol Period Events should result in Event Notification OAMPDUs generated by the OAM layer. By default, this object should have the value enabled(1) for Ethernet like interfaces that support OAM. If the OAM layer does not support event notifications (as indicated via the dot3OamFunctionsSupported attribute), this value is ignored.
U32 dot3OamErrFramePeriodWindow	1.3.6.1.2.1.9908.1.5.1.6	Unsigned32	read-write	The number of frames over which the threshold is defined. The default value of the window is the number of minimum size Ethernet frames that can be received over the physical layer in one second. If dot3OamErrFramePeriodThreshold frame errors occur within a window of dot3OamErrFramePeriodWindow frames, an Event Notification OAMPDU should be generated with an Errored Frame Period Event TLV indicating the threshold has been crossed in this window.
U32 dot3OamErrFramePeriodThreshold	1.3.6.1.2.1.9908.1.5.1.7	Unsigned32	read-write	The number of frame errors that must occur for this event to be triggered. The default value is one frame error. If dot3OamErrFramePeriodThreshold frame errors occur within a window of dot3OamErrFramePeriodWindow frames, an Event Notification OAMPDU should be generated with an Errored Frame Period Event TLV indicating the threshold has been crossed in this window.
INT dot3OamErrFramePeriodEvNotifEnable	1.3.6.1.2.1.9908.1.5.1.8	INTEGER	read-write	Indicates whether the occurence of an Errored Frame Period Event should result in an Event Notification OAMPDU generated by the OAM layer. By default, this object should have the value enabled(1) for Ethernet like interfaces that support OAM. If the OAM layer does not support event notifications (as indicated via the dot3OamFunctionsSupported attribute), this value is ignored.
U32 dot3OamErrFrameWindow	1.3.6.1.2.1.9908.1.5.1.9	Unsigned32	read-write	The amount of time (in 100ms increments) over which the threshold is defined. The default value is 10 (1 second). If dot3OamErrFrameThreshold frame errors occur within a window of dot3OamErrFrameWindow seconds (measured in tenths of seconds), an Event Notification OAMPDU should be generated with an Errored Frame Event TLV indicating the threshold has been crossed in this window.
U32 dot3OamErrFrameThreshold	1.3.6.1.2.1.9908.1.5.1.10	Unsigned32	read-write	The number of frame errors that must occur for this event to be triggered. The default value is one frame error. If dot3OamErrFrameThreshold frame errors occur within a window of dot3OamErrFrameWindow (in tenths of seconds), an Event Notification OAMPDU should be generated with an Errored Frame Event TLV indicating the threshold has been crossed in this window.
INT dot3OamErrFrameEvNotifEnable	1.3.6.1.2.1.9908.1.5.1.11	INTEGER	read-write	Indicates whether the occurence of an Errored Frame Event should result in an Event Notification OAMPDU generated by the OAM layer. By default, this object should have the value enabled(1) for Ethernet like interfaces that support OAM. If the OAM layer does not support event notifications (as indicated via the dot3OamFunctionsSupported attribute), this value is ignored.
I32 dot3OamErrFrameSecsSummaryWindow	1.3.6.1.2.1.9908.1.5.1.12	Integer32	read-write	The amount of time (in 100ms intervals) over which the threshold is defined. The default value is 100 (10 seconds). If dot3OamErrFrameSecsSummaryThreshold frame errors occur within a window of dot3OamErrFrameSecsSummaryWindow (in tenths of seconds), an Event Notification OAMPDU should be generated with an Errored Frame Seconds Summary Event TLV indicating the threshold has been crossed in this window.
I32 dot3OamErrFrameSecsSummaryThreshold	1.3.6.1.2.1.9908.1.5.1.13	Integer32	read-write	The number of errored frame seconds that must occur for this event to be triggered. The default value is one errored frame second. If dot3OamErrFrameSecsSummaryThreshold frame errors occur within a window of dot3OamErrFrameSecsSummaryWindow (in tenths of seconds), an Event Notification OAMPDU should be generated with an Errored Frame Seconds Summary Event TLV indicating the threshold has been crossed in this window.
INT dot3OamErrFrameSecsEvNotifEnable	1.3.6.1.2.1.9908.1.5.1.14	INTEGER	read-write	Indicates whether the occurence of an Errored Frame Seconds Summary Event should result in an Event Notification OAMPDU generated by the OAM layer. By default, this object should have the value enabled(1) for Ethernet like interfaces that support OAM. If the OAM layer does not support event notifications (as indicated via the dot3OamFunctionsSupported attribute), this value is ignored.
INT dot3OamDyingGaspEnable	1.3.6.1.2.1.9908.1.5.1.15	INTEGER	read-write	Indicates whether the local device should attempt to indicate a dying gasp fault via the OAMPDU flags field to its peer OAM entity. If the system does not support dying gasp capability, setting this object has no effect, and reading the object should always result in 'disabled(2)'. By default, this object should have the value enabled(1) for Ethernet like interfaces that support OAM. If the OAM layer does not support event notifications (as indicated via the dot3OamFunctionsSupported attribute), this value is ignored.
INT dot3OamCriticalEventEnable	1.3.6.1.2.1.9908.1.5.1.16	INTEGER	read-write	Indicates whether the local device should attempt to indicate a critical event fault via the OAMPDU flags field to its peer OAM entity. If the system does not support critical event capability, setting this object has no effect, and reading the object should always result in 'disabled(2)'. By default, this object should have the value enabled(1) for Ethernet like interfaces that support OAM. If the OAM layer does not support event notifications (as indicated via the dot3OamFunctionsSupported attribute), this value is ignored.
dot3OamEventLogTable	1.3.6.1.2.1.9908.1.6		not-accessible	This table records a history of the events that have occurred at the Ethernet OAM level. These events can include locally detected events, which may result in locally generated OAMPDUs, and remotely detected events, which are detected by the OAM peer entity and signaled to the local entity via Ethernet OAM. Ethernet OAM events can be signaled by Event Notification OAMPDUs or by the flags field in any OAMPDU.
dot3OamEventLogEntry	1.3.6.1.2.1.9908.1.6.1		not-accessible	An entry in the dot3OamEventLogTable.
U32 dot3OamEventLogIndex	1.3.6.1.2.1.9908.1.6.1.1	Unsigned32	not-accessible	An arbitrary integer for identifiying individual events within the event log.
TIM dot3OamEventLogTimestamp	1.3.6.1.2.1.9908.1.6.1.2	TimeStamp	read-only	The value of sysUpTime at the time of the logged event. For locally generated events, the time of the event can be accurately retrieved from sysUpTime. For remotely generated events, the time of the event is indicated by the reception of the Event Notification OAMPDU indicating the event occurred on the peer. A system may attempt to adjust the timestamp value to more accurately reflect the time of the event at the peer OAM entity by using other information, such as that found in the timestamp found of the Event Notification TLVs, which provides an indication of the relative time between events at the peer entity.
DOT dot3OamEventLogOui	1.3.6.1.2.1.9908.1.6.1.3	Dot3Oui	read-only	The OUI of the entity defining the object type. All IEEE 802.3 defined events (as appearing in [802.3ah] except for the Organizationally Unique Event TLVs) use the IEEE 802.3 OUI of 0x0180C2. Organizations defining their own Event Notification TLVs include their OUI in the Event Notification TLV which gets reflected here.
U32 dot3OamEventLogType	1.3.6.1.2.1.9908.1.6.1.4	Unsigned32	read-only	The type of event that generated this entry in the event log. When the OUI is the IEEE 802.3 OUI of 0x0180C2, the following event types are defined: erroredSymbolEvent(1), erroredFramePeriodEvent (2), erroredFrameEvent(3), erroredFrameSecondsEvent(4), linkFault(256), dyingGaspEvent(257), criticalLinkEvent(258) The first four are considered threshold crossing events as they are generated when a metric exceeds a given value within a specified window. The other three are not threshold crossing events. When the OUI is not 0x0180C2, then some other organization has defined the event space. If event subtyping is known to the implementation, it may be reflected here. Otherwise, this value should return all Fs (0xFFFFFFFF).
INT dot3OamEventLogLocation	1.3.6.1.2.1.9908.1.6.1.5	INTEGER	read-only	Whether this event occurred locally, or was received from the OAM peer via Ethernet OAM.
U32 dot3OamEventLogWindowHi	1.3.6.1.2.1.9908.1.6.1.6	Unsigned32	read-only	If the event represents a threshold crossing event, the two objects dot3OamEventWindowHi and dot3OamEventWindowLo form an unsigned 64-bit integer yielding the window over which the value was measured for the threshold crossing event (e.g. 5, when 11 occurrences happened in 5 seconds while the threshold was 10). The two objects are combined as: dot3OamEventLogWindow = ((2^32) * dot3OamEventLogWindowHi) + dot3OamEventLogWindowLo Otherwise, this value is returned as all F's (0xFFFFFFFF) and adds no useful information.
U32 dot3OamEventLogWindowLo	1.3.6.1.2.1.9908.1.6.1.7	Unsigned32	read-only	If the event represents a threshold crossing event, the two objects dot3OamEventWindowHi and dot3OamEventWindowLo form an unsigned 64-bit integer yielding the window over which the value was measured for the threshold crossing event (e.g. 5, when 11 occurrences happened in 5 seconds while the threshold was 10). The two objects are combined as: dot3OamEventLogWindow = ((2^32) * dot3OamEventLogWindowHi) + dot3OamEventLogWindowLo Otherwise, this value is returned as all F's (0xFFFFFFFF) and adds no useful information.
U32 dot3OamEventLogThresholdHi	1.3.6.1.2.1.9908.1.6.1.8	Unsigned32	read-only	If the event represents a threshold crossing event, the two objects dot3OamEventThresholdHi and dot3OamEventThresholdLo form an unsigned 64-bit integer yielding the value that was crossed for the threshold crossing event (e.g. 10, when 11 occurrences happened in 5 seconds while the threshold was 10). The two objects are combined as: dot3OamEventLogThreshold = ((2^32) * dot3OamEventLogThresholdHi) + dot3OamEventLogThresholdLo Otherwise, this value is returned as all F's (0xFFFFFFFF) and adds no useful information.
U32 dot3OamEventLogThresholdLo	1.3.6.1.2.1.9908.1.6.1.9	Unsigned32	read-only	If the event represents a threshold crossing event, the two objects dot3OamEventThresholdHi and dot3OamEventThresholdLo form an unsigned 64-bit integer yielding the value that was crossed for the threshold crossing event (e.g. 10, when 11 occurrences happened in 5 seconds while the threshold was 10). The two objects are combined as: dot3OamEventLogThreshold = ((2^32) * dot3OamEventLogThresholdHi) + dot3OamEventLogThresholdLo Otherwise, this value is returned as all F's (0xFFFFFFFF) and adds no useful information.
NUM dot3OamEventLogValue	1.3.6.1.2.1.9908.1.6.1.10	CounterBasedGauge64	read-only	If the event represents a threshold crossing event, this value indicates the value of the parameter within the given window that generated this event (e.g. 11, when 11 occurrences happened in 5 seconds while the threshold was 10). Otherwise, this value is returned as all F's (0xFFFFFFFFFFFFFFFF) and adds no useful information.
NUM dot3OamEventLogRunningTotal	1.3.6.1.2.1.9908.1.6.1.11	CounterBasedGauge64	read-only	This value respresents the total number of times this occurence has happened since the last reset (e.g. 3253, when 3253 symbol errors have occurred since the last reset, which has resulted in 51 symbol error threshold crossing events since the last reset).
U32 dot3OamEventLogEventTotal	1.3.6.1.2.1.9908.1.6.1.12	Unsigned32	read-only	This value respresents the total number of times one or ore of these occurences have resulted in an event (e.g. 51 when 3253 symbol errors have occurred since the last reset, which has resulted in 51 symbol error threshold crossing events since the last reset).
dot3OamNotifs	1.3.6.1.2.1.9908.1.7
dot3OamNotifsPrefix	1.3.6.1.2.1.9908.1.7.0
NTF dot3OamThresholdEvent	1.3.6.1.2.1.9908.1.7.0.1			A dot3OamThresholdEvent notification is sent when a local or remote threshold crossing event is detected. A local threshold crossing event is detected by the local entity, while a remote threshold crossing event is detected by the reception of an Ethernet OAM Event Notification OAMPDU indicating a threshold event. This notification should not be sent more than once per second. The management entity should periodically check dot3OamEventLogTable to detect any missed events.
NTF dot3OamNonThresholdEvent	1.3.6.1.2.1.9908.1.7.0.2			A dot3OamNonThresholdEvent notification is sent when a local or remote non-threshold crossing event is detected. A local event is detected by the local entity, while a remote event is detected by the reception of an Ethernet OAM Event Notification OAMPDU indicating a non-threshold crossing event. This notification should not be sent more than once per second. The management entity should periodically check dot3OamEventLogTable to detect any missed events.
dot3OamConformance	1.3.6.1.2.1.9908.2
dot3OamGroups	1.3.6.1.2.1.9908.2.1
dot3OamControlGroup	1.3.6.1.2.1.9908.2.1.1			A collection of objects providing the abilities, configuration, and status of an Ethernet OAM entity.
dot3OamPeerGroup	1.3.6.1.2.1.9908.2.1.2			A collection of objects providing the abilities, configuration, and status of a peer Ethernet OAM entity.
dot3OamStatsBaseGroup	1.3.6.1.2.1.9908.2.1.3			A collection of objects providing the statistics for the number of various transmit and recieve events for OAM on an Ethernet like interface. Note that all of these counters must be supported even if the related function (as described in dot3OamFunctionsSupported) is not supported.
dot3OamLoopbackGroup	1.3.6.1.2.1.9908.2.1.4			A collection of objects for controlling the OAM remote loopback function.
dot3OamErrSymbolPeriodEventGroup	1.3.6.1.2.1.9908.2.1.5			A collection of objects for configuring the thresholds for an Errored Symbol Period Event. Each [802.3ah] defined Event Notification TLV has its own conformance group because each event can be implemented independently of any other.
dot3OamErrFramePeriodEventGroup	1.3.6.1.2.1.9908.2.1.6			A collection of objects for configuring the thresholds for an Errored Frame Period Event. Each [802.3ah] defined Event Notification TLV has its own conformance group because each event can be implemented independently of any other.
dot3OamErrFrameEventGroup	1.3.6.1.2.1.9908.2.1.7			A collection of objects for configuring the thresholds for an Errored Frame Event. Each [802.3ah] defined Event Notification TLV has its own conformance group because each event can be implemented independently of any other.
dot3OamErrFrameSecsSummaryEventGroup	1.3.6.1.2.1.9908.2.1.8			A collection of objects for configuring the thresholds for an Errored Frame Seconds Summary Event. Each [802.3ah] defined Event Notification TLV has its own conformance group because each event can be implemented independently of any other.
dot3OamFlagEventGroup	1.3.6.1.2.1.9908.2.1.9			A collection of objects for configuring the sending OAMPDUs with the critical event flag or dying gasp flag enabled.
dot3OamEventLogGroup	1.3.6.1.2.1.9908.2.1.10			A collection of objects for configuring the thresholds for an Errored Frame Seconds Summary Event and maintaining the event information.
dot3OamNotificationGroup	1.3.6.1.2.1.9908.2.1.11			A collection of notifications used by Ethernet OAM to signal to a management entity that local or remote events have occured on a specified Ethernet link.
dot3OamCompliances	1.3.6.1.2.1.9908.2.2
dot3OamCompliance	1.3.6.1.2.1.9908.2.2.1			The compliance statement for managed entities supporting OAM on Ethernet like interfaces.

RFC description

Ethernet First Mile OAM MIB for managing Ethernet OAM features based on IEEE 802.3ah standard.

Start monitoring Ethernet access/carrier equipment supporting 802.3ah EFM OAM (vendor-neutral IETF standard) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download EFM-COMMON-MIB

What Is EFM-COMMON-MIB?

Supported Devices

Monitoring Examples

This MIB depends on

Related MIBs

RFC description